-
Structure of rotator phases formed in C$_{13}$-C$_{21}$ alkanes and their mixtures: in bulk and in emulsion drops
Authors:
Diana Cholakova,
Martin Pantov,
Slavka Tcholakova,
Nikolai Denkov
Abstract:
Crystallization of alkane mixtures has been studied extensively for decades. However, majority of the available data consider the behaviour of alkanes with chain length of 21 C-atoms or more. Furthermore, important information about the changes of the unit cell structure with temperature is practically absent. In this work, the phase behavior of several pure alkanes $C_{n}H_{2n+2}$, with $n$ rangi…
▽ More
Crystallization of alkane mixtures has been studied extensively for decades. However, majority of the available data consider the behaviour of alkanes with chain length of 21 C-atoms or more. Furthermore, important information about the changes of the unit cell structure with temperature is practically absent. In this work, the phase behavior of several pure alkanes $C_{n}H_{2n+2}$, with $n$ ranging between 13 and 21, and their binary, ternary or multi-component equimolar mixtures are investigated by X-ray scattering techniques. Both bulk alkanes and oil-in-water emulsions of the same alkanes were studied. The obtained results show formation of mixed rotator phases for all systems with chain length difference between the neighbouring alkanes of $Δn \leqslant 3$. Partial demixing is observed when $Δn = 4 $, yet the main fraction of the alkane molecules arranges in a mixed rotator phase in these samples. This demixing is suppressed if an alkane with intermediate chain length is added to the mixture. Interestingly, a steep temperature dependence of the interlamellar spacing in mixed rotator phases was observed upon cooling at temperatures down to 10°C below the melting temperature of the mixture. The volumetric coefficient of thermal expansion of the rotator phases of mixed alkanes ($α_{V} \approx 2$ x $10^{-3} °C ^{-1} $) is around 10 times bigger compared to that of the rotator phases of pure alkanes. The experiments performed with emulsion drops containing the same alkane mixture while stabilized by different surfactants, showed that the surfactant template also affects the final lattice spacing which is observed at low temperatures. In contrast, no such dependence was observed for drops stabilized by the same surfactant while having different initial diameters - in this case only the initial temperature of the crystallization onset was affected.
△ Less
Submitted 12 December, 2023;
originally announced December 2023.
-
Polymorphic phase transitions in bulk triglyceride mixtures
Authors:
Diana Cholakova,
Slavka Tcholakova,
Nikolai Denkov
Abstract:
Triacylglycerols (TAGs) are among the most important ingredients in food, cosmetic and pharmaceutical products. Many physical properties of such products, incl. morphology, texture and rheology, are determined by the phase behaviour of the included TAGs. Triglycerides are also of special interest for the production of solid lipid nanoparticles, applied for controlled drug delivery and for encapsul…
▽ More
Triacylglycerols (TAGs) are among the most important ingredients in food, cosmetic and pharmaceutical products. Many physical properties of such products, incl. morphology, texture and rheology, are determined by the phase behaviour of the included TAGs. Triglycerides are also of special interest for the production of solid lipid nanoparticles, applied for controlled drug delivery and for encapsulation of bioactive ingredients. In this paper, we study the polymorphic behaviour of complex TAG mixtures, composed of 2 to 6 mixed TAGs, by differential scanning calorimetry and X-ray scattering techniques, aiming to reveal the general rules for their phase behaviour upon cooling and heating. The results show that two or more coexisting phases form upon solidification $(α$, $β'$ and/or $β)$, the number of which depends strongly on the cooling rate and on the number of components in the mixture. No completely miscible $α$- or $β'$-phases were observed. The structure of the most stable $β$ polymorphs, formed upon subsequent heating of the solidified samples, does not depend on the thermal history of the samples. For all mixtures studied, we observed one-component $β$ domains, coexisting with binary mixed $β$ domains with composition and structure which do not depend on the specific TAG ratio in the mixture. In other words, for a mixture with $k$ saturated TAGs we observed $(2k-1)$ different $β$ phases. These conclusions provide some predictive power when analysing the phase transition properties of TAG mixtures.
△ Less
Submitted 23 March, 2023;
originally announced March 2023.
-
Role of particles size on the cohesive strength of non-sintered (green) ceramics
Authors:
M. Hristova,
I. Lesov,
L. Mihaylov,
N. Denkov,
S. Tcholakova
Abstract:
Preparation of particle-loaded foams, followed by drying, sintering and/or cross-linking are widely explored routes for developing lightweight ceramics with high mechanical strength. The non-sintered dry ceramic foams are less studied due to their intricate production and the assumed poor mechanical strength of the obtained "green" materials. Here we produce lightweight ceramics from foamed partic…
▽ More
Preparation of particle-loaded foams, followed by drying, sintering and/or cross-linking are widely explored routes for developing lightweight ceramics with high mechanical strength. The non-sintered dry ceramic foams are less studied due to their intricate production and the assumed poor mechanical strength of the obtained "green" materials. Here we produce lightweight ceramics from foamed particle suspensions containing spherical silica particles with radii varied between 4.5 nm and 7 μm. The wet foams were prepared in the presence of cationic surfactant and were dried at ambient conditions to obtain porous materials with mass densities between 100 and 700 kg/m3. The materials containing smaller particles exhibited much higher strength (up to 2000 times), approaching that of the sintered materials. A new theoretical expression for predicting the mechanical strength of such materials was derived and was used to explain the measured strengths of the produced materials through the van der Waals attractions between the particles in the final dry materials.
△ Less
Submitted 12 September, 2022;
originally announced September 2022.
-
Minimum Surfactant Concentration Required for Inducing Self-shaping of Oil Droplets and Competitive Adsorption Effects
Authors:
Jiale Feng,
Zhulieta Valkova,
E Emily Lin,
Ehsan Nourafkan,
Tiesheng Wang,
Slavka Tcholakova,
Radomir Slavchov,
Stoyan K. Smoukov
Abstract:
Surfactant choice is key in starting the phenomena of artificial morphogenesis, the bottom-up growth of geometric particles from cooled emulsion droplets, as well as the bottom-up self-assembly of rechargeable microswimmer robots from similar droplets. The choice of surfactant is crucial for the formation of a plastic phase at the oil-water interface, for the kinetics, and for the onset temperatur…
▽ More
Surfactant choice is key in starting the phenomena of artificial morphogenesis, the bottom-up growth of geometric particles from cooled emulsion droplets, as well as the bottom-up self-assembly of rechargeable microswimmer robots from similar droplets. The choice of surfactant is crucial for the formation of a plastic phase at the oil-water interface, for the kinetics, and for the onset temperature of these processes. But further details are needed to control these processes for bottom-up manufacturing and understand their molecular mechanisms. Still unknown are the minimum concentration of the surfactant necessary to induce the processes, or competing effects in a mixture of surfactants when only one is capable of inducing shapes. Here we systematically study the effect of surfactant nature and concentration on the shape-inducing behaviour of hexadecane-in-water emulsions with both cationic (CTAB) and non-ionic (Tween, Brij) surfactants over up to five orders of magnitude of concentration. The minimum effective concentration is found approximately equal to the critical micelle concentration (CMC), or the solubility limit below the Krafft point of the surfactant. However, the emulsions show low stability at the vicinity of CMC. In a mixed surfactant experiment (Tween 60 and Tween 20), where only one (Tween 60) can induce shapes we elucidate the role of competition at the interface during mixed surfactant adsorption by varying the composition. We find that a lower bound of ~ 75% surface coverage of the shape-inducing surfactant with C14 or longer chain length is necessary for self-shaping to occur. The resulting technique produces a clear visual readout of otherwise difficult to investigate molecular events and establish basic requirements for minimum concentration and protocols to find % surface coverage to induce oil self-shaping by surfactant mixtures.
△ Less
Submitted 16 August, 2022;
originally announced August 2022.
-
Flow reactor for preparation of lipid nanoparticles via temperature variations
Authors:
I. Lesov,
D. Glushkova,
D. Cholakova,
M. T. Georgiev,
S. Tcholakova,
S. K. Smoukov,
N. Denkov
Abstract:
Lipid nanoemulsions and nanosuspensions are used as flavor carriers and bubble stabilizers in soft drinks and foods, as well as delivery vehicles for lipophilic drugs in pharmaceutics. Common techniques for their formation are the high-pressure and ultrasonic homogenizers. These techniques dissipate most of the input energy, which results in excessive heating and generation of free radicals that m…
▽ More
Lipid nanoemulsions and nanosuspensions are used as flavor carriers and bubble stabilizers in soft drinks and foods, as well as delivery vehicles for lipophilic drugs in pharmaceutics. Common techniques for their formation are the high-pressure and ultrasonic homogenizers. These techniques dissipate most of the input energy, which results in excessive heating and generation of free radicals that might modify sensitive ingredients. Low energy methods are also used in some applications, but they have specific limitations restricting their universal use. In the current study, we propose an alternative approach - a flow reactor with a variable temperature, which utilizes the lipids' polymorphic transitions to induce spontaneous fragmentation of the lipid microparticles into nanoparticles. The reactor allows us to obtain emulsions or suspensions with particle diameters tunable between 20 and 800 nm when appropriate surfactants, temperature profiles, and flow rates are applied. The fragmentation is comparable to that in a high-pressure homogenizer at ca. 500 bars or higher, without creating emulsion overheating or cavitation typical for the conventional methods. The flow reactor can be scaled up to industrial applications using simple scaling rules.
△ Less
Submitted 22 June, 2022;
originally announced June 2022.
-
Self-emulsification in chemical and pharmaceutical technologies
Authors:
D. Cholakova,
Z. Vinarov,
S. Tcholakova,
N. Denkov
Abstract:
The interest in the low energy self-emulsification techniques has exploded in the recent years, driven by three main trends: by the transition to "greener" technologies in both its aspects - less energy consumption and replacement of the petrochemicals by natural ingredients; by the costly and maintenance demanding equipment for nanoemulsification; and by the quest for efficient and robust self-em…
▽ More
The interest in the low energy self-emulsification techniques has exploded in the recent years, driven by three main trends: by the transition to "greener" technologies in both its aspects - less energy consumption and replacement of the petrochemicals by natural ingredients; by the costly and maintenance demanding equipment for nanoemulsification; and by the quest for efficient and robust self-emulsifying formulations for oral drug delivery. Here we first present a brief overview of the main known low-energy methods for nanoemulsion formation, focusing on their mechanistic understanding and discussing some recent advances in their development and applications. Next, we review three conceptually new approaches for self-emulsification in chemical technologies, discovered in the last several years. The colloidal features and the specific requirements of the self-emulsifying drug-delivery systems (SEDDS) are also discussed briefly. Finally, we summarize the current trends and the main challenges in this vivid research area.
△ Less
Submitted 15 February, 2022;
originally announced February 2022.
-
Rheological properties of rotator and crystalline phases of alkanes
Authors:
Diana Cholakova,
Krastina Tsvetkova,
Slavka Tcholakova,
Nikolai Denkov
Abstract:
Linear long-chain organic molecules are known to form lamellar intermediate phases (called also rotator phases) between their fully ordered crystalline phases and their isotropic liquid phases. The properties of intermediate rotator phases are crucially important for various industrial and living nature processes, but the data for their rheological properties are almost missing, due to the specifi…
▽ More
Linear long-chain organic molecules are known to form lamellar intermediate phases (called also rotator phases) between their fully ordered crystalline phases and their isotropic liquid phases. The properties of intermediate rotator phases are crucially important for various industrial and living nature processes, but the data for their rheological properties are almost missing, due to the specific difficulties in the respective experiments. In the current study we describe a methodology for measuring and comparing the shear rheological properties of rotator (R) and crystalline (C) phases formed in bulk hydrocarbons at temperatures below the melting temperature. We apply this approach to characterize the rheological properties of R and C phases formed upon cooling of alkanes with chain length varied between 17 and 30 carbon atoms. For comparison, we study also several alkane mixtures and one alkene with double bond at the end of its chain. The obtained results show that the storage and loss moduli of the rotator phases are ca. 10-times lower than those of the respective crystalline phases. We found also that the rheological properties of the crystal phases depend mainly on the subcooling temperature below the crystallization temperature, while the R phases become softer with the increase of the molecular length. We explain these results by assuming that the rheological properties of the crystal phases are determined mainly by the sliding of the ordered crystal domains with respect to each other, while in the rotator phases we have multiple defects in the molecular packing which increase with the alkane length. The proposed methodology and the obtained results serve as a solid basis for further rheological studies of this important class of technological systems.
△ Less
Submitted 3 November, 2021;
originally announced November 2021.
-
Rechargeable self-assembled droplet microswimmers driven by surface phase transitions
Authors:
Diana Cholakova,
Maciej Lisicki,
Stoyan K. Smoukov,
Slavka Tcholakova,
E. Emily Lin,
Jianxin Chen,
Gabriele De Canio,
Eric Lauga,
Nikolai Denkov
Abstract:
The design of artificial microswimmers is often inspired by the strategies of natural microorganisms. Many of these creatures exploit the fact that elasticity breaks the time-reversal symmetry of motion at low Reynolds numbers, but this principle has been notably absent from model systems of active, self-propelled microswimmers. Here we introduce a class of microswimmer that spontaneously self-ass…
▽ More
The design of artificial microswimmers is often inspired by the strategies of natural microorganisms. Many of these creatures exploit the fact that elasticity breaks the time-reversal symmetry of motion at low Reynolds numbers, but this principle has been notably absent from model systems of active, self-propelled microswimmers. Here we introduce a class of microswimmer that spontaneously self-assembles and swims without using external forces, driven instead by surface phase transitions induced by temperature variations. The swimmers are made from alkane droplets dispersed in aqueous surfactant solution, which start to self-propel upon cooling, pushed by rapidly growing thin elastic tails. When heated, the same droplets recharge by retracting their tails, swimming for up to tens of minutes in each cycle. Thermal oscillations of approximately 5 degrees Celsius induce the swimmers to harness heat from the environment and recharge multiple times. We develop a detailed elastohydrodynamic model of these processes and highlight the molecular mechanisms involved. The system offers a convenient platform for examining symmetry breaking in the motion of swimmers exploiting flagellar elasticity. The mild conditions and biocompatible media render these microswimmers potential probes for studying biological propulsion and interactions between artificial and biological swimmers.
△ Less
Submitted 21 July, 2021;
originally announced July 2021.
-
Rotator phases in hexadecane emulsion drops revealed by X-ray synchrotron techniques
Authors:
Diana Cholakova,
Desislava Glushkova,
Zhulieta Valkova,
Sonya Tsibranska-Gyoreva,
Krastina Tsvetkova,
Slavka Tcholakova,
Nikolai Denkov
Abstract:
Micrometer sized alkane-in-water emulsion drops, stabilized by appropriate long-chain surfactants, spontaneously break symmetry upon cooling and transform consecutively into series of regular shapes (Denkov et al., Nature 2015, 528, 392). Two mechanisms were proposed to explain this phenomenon of drop "self-shaping". One of these mechanisms assumes that thin layers of plastic rotator phase form at…
▽ More
Micrometer sized alkane-in-water emulsion drops, stabilized by appropriate long-chain surfactants, spontaneously break symmetry upon cooling and transform consecutively into series of regular shapes (Denkov et al., Nature 2015, 528, 392). Two mechanisms were proposed to explain this phenomenon of drop "self-shaping". One of these mechanisms assumes that thin layers of plastic rotator phase form at the drop surface around the freezing temperature of the oil. This mechanism has been supported by several indirect experimental findings but direct structural characterization has not been reported so far. We combine small- and wide-angle X-ray scattering (SAXS/WAXS) with optical microscopy and DSC measurements of self-shaping drops in emulsions. In the emulsions exhibiting drop self-shaping, the scattering spectra reveal the formation of intermediate, metastable rotator phases in the alkane drops before their crystallization. In addition, shells of rotator phase were observed to form in hexadecane drops, stabilized by C16EO10 surfactant. This rotator phase melts at ca. 16.6 °C which is significantly lower than the melting temperature of crystalline hexadecane, 18 °C. The scattering results are in a very good agreement with the complementary optical observations and DSC measurements.
△ Less
Submitted 5 July, 2021;
originally announced July 2021.
-
Cold-burst method for nanoparticle formation with natural triglyceride oils
Authors:
Diana Cholakova,
Desislava Glushkova,
Slavka Tcholakova,
Nikolai Denkov
Abstract:
Preparation of nanoemulsions of triglyceride oils in water usually requires high mechanical energy and sophisticated equipment. Recently, we showed that alpha-to-beta (viz. gel-to-crystal) phase transition, observed with most lipid substances (triglycerides, diglycerides, phospholipids, alkanes, etc.), may cause spontaneous disintegration of micro-particles of these lipids, dispersed in aqueous so…
▽ More
Preparation of nanoemulsions of triglyceride oils in water usually requires high mechanical energy and sophisticated equipment. Recently, we showed that alpha-to-beta (viz. gel-to-crystal) phase transition, observed with most lipid substances (triglycerides, diglycerides, phospholipids, alkanes, etc.), may cause spontaneous disintegration of micro-particles of these lipids, dispersed in aqueous solutions of appropriate surfactants, into nanometer particles/drops using a simple cooling/heating cycle of the lipid dispersion (Cholakova et al. ACS Nano 14 (2020) 8594). In the current study we show that this "cold-burst process" is observed also with natural oils of high practical interest, incl. coconut oil, palm kernel oil and cocoa butter. Mean drop diameters of ca. 50 to 100 nm were achieved with some of the studied oils. From the results of dedicated model experiments we conclude that intensive nano-fragmentation is observed when the following requirements are met: (1) The three phase contact angle at the air-water-solid lipid interface is below ca. 30 degrees; (2) The equilibrium surface tension of the surfactant solution is below ca. 30 mN/m and the dynamic surface tension decreases rapidly. (3) The surfactant solution contains non-spherical surfactant micelles. e.g. ellipsoidal micelles or bigger supramolecular aggregates; (4) The three phase contact angle measured at the contact line (frozen oil-melted oil-surfactant solution) is also relatively low. The mechanism(s) of the particle bursting process is revealed and, on this basis, the role of all these factors is clarified and discussed. We explain all main effects observed experimentally and define guiding principles for optimization of the cold-burst process in various, practically relevant lipid-surfactant systems.
△ Less
Submitted 6 July, 2021; v1 submitted 4 February, 2021;
originally announced February 2021.
-
Nanopore and nanoparticle formation with lipids, undergoing polymorphic phase transitions
Authors:
Diana Cholakova,
Desislava Glushkova,
Slavka Tcholakova,
Nikolai Denkov
Abstract:
We describe several unexpected phenomena, caused by a solid-solid phase transition (gel-to-crystal) typical for all main classes of lipid substances - phospholipids, triglycerides, diglycerides, alkanes, etc. We discovered that this transition leads to spontaneous formation of a network of nanopores, spreading across the entire lipid structure. These nanopores are spontaneously impregnated (floode…
▽ More
We describe several unexpected phenomena, caused by a solid-solid phase transition (gel-to-crystal) typical for all main classes of lipid substances - phospholipids, triglycerides, diglycerides, alkanes, etc. We discovered that this transition leads to spontaneous formation of a network of nanopores, spreading across the entire lipid structure. These nanopores are spontaneously impregnated (flooded) by water when appropriate surfactants are present, thus fracturing the lipid structure at a nano-scale. As a result, spontaneous disintegration of the lipid into nanoparticles or formation of double emulsions is observed, just by cooling and heating of an initial coarse lipid-in-water dispersion around the lipid melting temperature. The process of nanoparticle formation is effective even after incorporation of medical drugs of high load, up to 50 % in the lipid phase. The role of the main governing factors is clarified, the procedure is optimized, and the possibility for its scaling-up to industrially relevant amounts is demonstrated.
△ Less
Submitted 25 June, 2020;
originally announced June 2020.
-
Origin of the extremely high elasticity of bulk emulsions, stabilized by Yucca Schidigera saponins
Authors:
Sonya Tsibranska,
Slavka Tcholakova,
Konstantin Golemanov,
Nikolai Denkov,
Luben Arnaudov,
Eddie Pelan,
Simeon D. Stoyanov
Abstract:
We found experimentally that the elasticity of sunflower oil-in-water emulsions (SFO-in-W) stabilized by Yucca Schidigera Roezl saponin extract, is by more than 50 times higher as compared to the elasticity of common emulsions. We revealed that strong specific interactions between the phytosterols from the non-purified oil and the saponins from the Yucca extract lead to the formation of nanostruct…
▽ More
We found experimentally that the elasticity of sunflower oil-in-water emulsions (SFO-in-W) stabilized by Yucca Schidigera Roezl saponin extract, is by more than 50 times higher as compared to the elasticity of common emulsions. We revealed that strong specific interactions between the phytosterols from the non-purified oil and the saponins from the Yucca extract lead to the formation of nanostructured adsorption layers which are responsible for the very high elasticity of the oil-water interface and of the respective bulk emulsions. Remarkably, this extra high emulsion elasticity inhibits the emulsion syneresis even at 65 vol % of the oil drops. These emulsions remain homogeneous and stable even after 30 days of shelf-storage. These results demonstrate that the combination of saponin and phytosterols is a powerful new approach to structure oil-in-water emulsions with potential applications for formulating healthier functional food.
△ Less
Submitted 5 February, 2020;
originally announced February 2020.
-
Role of interfacial elasticity for the rheological properties of saponin-stabilized emulsions
Authors:
Sonya Tsibranska,
Slavka Tcholakova,
Konstantin Golemanov,
Nikolai Denkov,
Eddie Pelan,
Simeon D. Stoyanov
Abstract:
Hypothesis Saponins are natural surfactants which can provide highly viscoelastic interfaces. This property can be used to quantify precisely the effect of interfacial dilatational elasticity on the various rheological properties of bulk emulsions. Experiments We measured the interfacial dilatational elasticity of adsorption layers from four saponins (Quillaja, Escin, Berry, Tea) adsorbed on hexad…
▽ More
Hypothesis Saponins are natural surfactants which can provide highly viscoelastic interfaces. This property can be used to quantify precisely the effect of interfacial dilatational elasticity on the various rheological properties of bulk emulsions. Experiments We measured the interfacial dilatational elasticity of adsorption layers from four saponins (Quillaja, Escin, Berry, Tea) adsorbed on hexadecane-water and sunflower oil-water interfaces. In parallel, the rheological properties under steady and oscillatory shear deformations were measured for bulk emulsions, stabilized by the same saponins (oil volume fraction between 75 and 85 %). Findings Quillaja saponin and Berry saponin formed solid adsorption layers (shells) on the SFO-water interface. As a consequence, the respective emulsions contained non-spherical drops. For the other systems, the interfacial elasticities varied between 2 mN/m and 500 mN/m. We found that this interfacial elasticity has very significant impact on the emulsion shear elasticity, moderate effect on the dynamic yield stress, and no effect on the viscous stress of the respective steadily sheared emulsions. The last conclusion is not trivial, because the dilatational surface elasticity is known to have strong impact on the viscous stress of steadily sheared foams. Mechanistic explanations of all observed effects are described.
△ Less
Submitted 27 December, 2019;
originally announced December 2019.
-
Foamability of aqueous solutions: Role of surfactant type and concentration
Authors:
B. Petkova,
S. Tcholakova,
M. Chenkova,
K. Golemanov,
N. Denkov,
D. Thorley,
S. Stoyanov
Abstract:
In this paper we study the main surface characteristics which control the foamability of solutions of various surfactants. Experiments with anionic, cationic and nonionic surfactants with different head groups and chain lengths are performed in a wide concentration range, from 0.001 mM to 100 mM. The electrolyte concentration is also varied from 0 up to 100 mM. For all surfactants studied, three r…
▽ More
In this paper we study the main surface characteristics which control the foamability of solutions of various surfactants. Experiments with anionic, cationic and nonionic surfactants with different head groups and chain lengths are performed in a wide concentration range, from 0.001 mM to 100 mM. The electrolyte concentration is also varied from 0 up to 100 mM. For all surfactants studied, three regions in the dependence of the foamability, VA, on the logarithm of surfactant concentration, lgCS, are observed. In Region 1, VA is very low and depends weakly on CS. In Region 2, VA increases steeply with CS. In Region 3, VA reaches a plateau. A key new element in our interpretation of the foaming data is that we use the surface tension measurements to determine the dependence of the main surface properties (surfactant adsorption, surface coverage and surface elasticity) on the surface age of the bubbles. In this way we interpret the results from the foaming tests by considering the properties of the dynamic adsorption layers, formed during foaming. The data for the nonionic and ionic surfactants merge around two master curves when plotted as a function of the surface coverage, the surface mobility factor, or the Gibbs elasticity of the dynamic adsorption layers. This difference between the ionic and nonionic surfactants is explained with the important contribution of the electrostatic repulsion between the foam film surfaces for the ionic surfactants which stabilizes the dynamic foam films even at moderate surface coverage and at relatively high ionic strength. In contrast, the films formed from solutions of nonionic surfactants are stabilized via steric repulsion which becomes sufficiently high to prevent bubble coalescence only at rather high surface coverage (> 90 %) which corresponds to related high Gibbs elasticity (> 150 mN/m) and low surface mobility of the dynamic adsorption layers.
△ Less
Submitted 17 December, 2019;
originally announced December 2019.
-
Food grade nanoemulsions preparation by rotor-stator homogenization
Authors:
Dilek Gazolu-Rusanova,
Ivan Lesov,
Slavka Tcholakova,
Nikolai Denkov,
Badreddine Ahtchi
Abstract:
High-pressure homogenizers, typically used for producing nanoemulsions at the industrial scale, are energy and maintenance intensive, and limited to produce only dilute, low viscosity nanoemulsions. We propose an alternative approach to produce dilute to concentrated food-grade nanoemulsions with droplet size ranging between 100 and 500 nm using rotor-stator homogenization. Gum Arabic (GA) or modi…
▽ More
High-pressure homogenizers, typically used for producing nanoemulsions at the industrial scale, are energy and maintenance intensive, and limited to produce only dilute, low viscosity nanoemulsions. We propose an alternative approach to produce dilute to concentrated food-grade nanoemulsions with droplet size ranging between 100 and 500 nm using rotor-stator homogenization. Gum Arabic (GA) or modified starch (MS) was used as both viscosity modifier and emulsion stabilizer. GA and MS have relatively low surface activity compared to the common low-molecular-mass surfactants used typically for nanoemulsion preparation. The main differences between GA and MS are the lower viscosity of the GA solutions, compared to MS solutions, and the faster adsorption of MS, as compared to GA. The obtained results show that stable nanoemulsions are formed by rotor-stator homogenization when the rapidly adsorbing MS is used as emulsifier. Much larger drops are formed during emulsification with GA, which is due to significant drop-drop coalescence in the respective emulsions. The experimental results for the nanoemulsions prepared with MS are well-described by the theoretical expression for emulsification in turbulent viscous regime, after proper account for the effects of temperature and drop-drop interactions in the sheared emulsions.
△ Less
Submitted 17 December, 2019;
originally announced December 2019.
-
Spontaneous particle desorption and "Gorgon" drop formation from particle-armored oil drops upon cooling
Authors:
Diana Cholakova,
Zhulieta Valkova,
Slavka Tcholakova,
Nikolai Denkov,
Bernard P. Binks
Abstract:
Drop "self-shaping" is a phenomenon in which cooled oily emulsion drops undergo a spectacular series of shape transformations (Denkov et al., Nature 528, 2015, 392). Solid particles adsorbed on the oil-water interface could affect this drop self-shaping process in multiple ways which have not been studied. We prepared Pickering emulsions stabilized by spherical latex particles and afterwards added…
▽ More
Drop "self-shaping" is a phenomenon in which cooled oily emulsion drops undergo a spectacular series of shape transformations (Denkov et al., Nature 528, 2015, 392). Solid particles adsorbed on the oil-water interface could affect this drop self-shaping process in multiple ways which have not been studied. We prepared Pickering emulsions stabilized by spherical latex particles and afterwards added surfactant of low concentration which enabled drop self-shaping. Next we observed by optical microscopy the processes which occur upon emulsion cooling. Several new processes were observed: (1) Adsorbed latex particles rearranged into regular hexagonal lattices upon freezing of the surfactant adsorption layer. (2) Spontaneous particle desorption from the drop surface was observed at a certain temperature - this phenomenon is rather remarkable, as the solid particles are known to irreversibly adsorb on fluid interfaces. (3) Very strongly adhered particles to drop surfaces acted as a template to enable the formation of tens to hundreds of semi-liquid fibers, growing outwards from the drop surface, thus creating a shape resembling the Gorgon head from Greek mythology. We provide mechanistic explanations of all observed phenomena using our understanding of the rotator phase formation on the surface of cooled drops.
△ Less
Submitted 26 November, 2019; v1 submitted 2 November, 2019;
originally announced November 2019.
-
Surface phase transitions in foams and emulsions
Authors:
Nikolai Denkov,
Slavka Tcholakova,
Diana Cholakova
Abstract:
Surface phase transitions in surfactant adsorption layers are known to affect the dynamic properties of foams and to induce surface nucleation in freezing emulsion drops. Recently, these transitions were found to play a role in several other phenomena, opening new opportunities for controlling foam and emulsion properties. This review presents a brief outlook of the emerging opportunities in this…
▽ More
Surface phase transitions in surfactant adsorption layers are known to affect the dynamic properties of foams and to induce surface nucleation in freezing emulsion drops. Recently, these transitions were found to play a role in several other phenomena, opening new opportunities for controlling foam and emulsion properties. This review presents a brief outlook of the emerging opportunities in this area. Three topics are emphasized: (1) The use of surfactant mixtures for inducing phase transitions on bubble surfaces in foams; (2) The peculiar properties of natural surfactants saponins which form extremely viscoelastic surface layers; and (3) The main phenomena in emulsions, for which the surface phase transitions are important. The overall conclusion from the reviewed literature is that surface phase transitions could be used as a powerful tool to control many foam and emulsion properties, but we need deeper understanding of the underlying phenomena to explore fully these opportunities.
△ Less
Submitted 11 November, 2019; v1 submitted 7 October, 2019;
originally announced October 2019.
-
Jamming in sheared foams and emulsions, explained by critical instability of the films between neighboring bubbles and drops
Authors:
N. D. Denkov,
S. Tcholakova,
K. Golemanov,
A. Lips
Abstract:
Phenomenon of foam and emulsion jamming at low shear rates is explained by considering the dynamics of thinning in the transient film, formed between the neighboring bubbles and drops. After gradually thinning down to a critical thickness, these films undergo instability transition and thin stepwise, forming the so-called "black films", which are only several nanometers thick and, thereby, lead…
▽ More
Phenomenon of foam and emulsion jamming at low shear rates is explained by considering the dynamics of thinning in the transient film, formed between the neighboring bubbles and drops. After gradually thinning down to a critical thickness, these films undergo instability transition and thin stepwise, forming the so-called "black films", which are only several nanometers thick and, thereby, lead to stronger adhesion between the dispersed particles. Theoretical analysis shows that such film thickness instability occurs only if the contact time between the bubbles/drops in sheared foam/emulsion is sufficiently long, which corresponds to sufficiently low (critical) rate of shear. Explicit expression for this critical rate is proposed and compared to experimental data.
△ Less
Submitted 23 January, 2009;
originally announced January 2009.
-
Theoretical model of viscous friction inside steadily sheared foams and concentrated emulsions
Authors:
S. Tcholakova,
N. D. Denkov,
K. Golemanov,
K. P. Ananthapadmanabhan,
A. Lips
Abstract:
In a recent letter (Denkov et al., Phys. Rev. Lett., vol. 100 (2008) p. 138301) we calculated theoretically the macroscopic viscous stress of steadily sheared foam/emulsion from the energy dissipated inside the transient planar films, formed between neighboring bubbles/drops in the shear flow. The model predicts that the viscous stress in these systems should be a proportional to Ca^1/2, where C…
▽ More
In a recent letter (Denkov et al., Phys. Rev. Lett., vol. 100 (2008) p. 138301) we calculated theoretically the macroscopic viscous stress of steadily sheared foam/emulsion from the energy dissipated inside the transient planar films, formed between neighboring bubbles/drops in the shear flow. The model predicts that the viscous stress in these systems should be a proportional to Ca^1/2, where Ca is the capillary number and n = 1/2 is the power-law index. In the current paper we explain in detail our model and develop it further in several aspects: First, we extend the model to account for the effects of viscous friction in the curved meniscus regions, surrounding the planar films, on the dynamics of film formation and on the total viscous stress. Second, we consider the effects of surface forces (electrostatic, van der Waals, etc.) acting between the surfaces of the neighboring bubbles/drops and show that these forces could be important in emulsions, due to the relatively small thickness of emulsion films (often comparable to the range of action of the surface forces). Third, additional consideration is made for bubbles/drops exhibiting high surface viscosity, for which we demonstrate an additional contribution to the macroscopic viscous stress, created by the surface dissipation of energy. The new upgraded model predicts that the energy dissipation at the bubble/drop surface leads to power-law index n < 1/2, whereas the contribution of the surface forces leads to n > 1/2, which explains the rich variety of foam/emulsion behaviors observed upon steady shear. Various comparisons are made between model predictions and experimental results for both foams and emulsions, and a very good agreement is found.
△ Less
Submitted 28 May, 2008;
originally announced May 2008.
