-
Particle Re-Suspension in Two-Phase Dispersed Rayleigh-Bénard Convection
Authors:
Xianyang Chen,
Rodolfo Ostilla Monico,
Daniel Floryan,
Andrea Prosperetti
Abstract:
The process by which particles are entrained by the fluid in Rayleigh-Bénard convection is studied by means of particle-resolved numerical simulations in a periodic domain at a Rayleigh number of $10^7$. The fluid Prandtl number is 1 and the particle-to-fluid density ratio 1.1. The results show that the horizontal velocity field near the bottom of the cell accumulates particles in heaps, or `dunes…
▽ More
The process by which particles are entrained by the fluid in Rayleigh-Bénard convection is studied by means of particle-resolved numerical simulations in a periodic domain at a Rayleigh number of $10^7$. The fluid Prandtl number is 1 and the particle-to-fluid density ratio 1.1. The results show that the horizontal velocity field near the bottom of the cell accumulates particles in heaps, or `dunes', at the base of ascending plumes. The dunes deflect the incoming flow, conferring to it a vertical velocity component which entrains the particles up the dune and into the plume. An experimental observation of this mechanism was briefly reported by Solomatov et al. (Earth Planet. Sc. Lett. 120, 387, 1993) but has not been considered further in the literature. By its very nature, such a process cannot be simulated by the point particle model. The final particle load carried by the convection depends both on the available gravitational energy of the fluid and on the effectiveness of the re-suspension mechanism.
△ Less
Submitted 3 October, 2024;
originally announced October 2024.
-
Crown formation from a cavitating bubble close to a free surface
Authors:
Youssef Saade,
Maziyar Jalaal,
Andrea Prosperetti,
Detlef Lohse
Abstract:
A rapidly growing bubble close to a free surface induces jetting: a central jet protruding outwards and a crown surrounding it at later stages. While the formation mechanism of the central jet is known and documented, that of the crown remains unsettled. We perform axisymmetric simulations of the problem using the free software program basilisk, where a finite-volume compressible solver has been i…
▽ More
A rapidly growing bubble close to a free surface induces jetting: a central jet protruding outwards and a crown surrounding it at later stages. While the formation mechanism of the central jet is known and documented, that of the crown remains unsettled. We perform axisymmetric simulations of the problem using the free software program basilisk, where a finite-volume compressible solver has been implemented, that uses a geometric Volume-of-Fluid method (VoF) for the tracking of the interface. We show that the mechanism of crown formation is a combination of a pressure distortion over the curved interface, inducing flow focusing, and of a flow reversal, caused by the second expansion of the toroidal bubble that drives the crown. The work culminates in a parametric study with the Weber number, the Reynolds number, the pressure ratio and the dimensionless bubble distance to the free surface as control parameters. Their effects on both the central jet and the crown are explored. For high Weber numbers, we observe the formation of weaker "secondary crowns", highly correlated with the third oscillation cycle of the bubble.
△ Less
Submitted 10 July, 2021;
originally announced July 2021.
-
Marangoni instability of a drop in a stably stratified liquid
Authors:
Yanshen Li,
Christian Diddens,
Andrea Prosperetti,
Detlef Lohse
Abstract:
Marangoni instabilities can emerge when a liquid interface is subjected to a concentration or temperature gradient. It is generally believed that for these instabilities bulk effects like buoyancy are negligible as compared to interfacial forces, especially on small scales. Consequently, the effect of a stable stratification on the Marangoni instability has hitherto been ignored. Here we report, f…
▽ More
Marangoni instabilities can emerge when a liquid interface is subjected to a concentration or temperature gradient. It is generally believed that for these instabilities bulk effects like buoyancy are negligible as compared to interfacial forces, especially on small scales. Consequently, the effect of a stable stratification on the Marangoni instability has hitherto been ignored. Here we report, for an immiscible drop immersed in a stably stratified ethanol-water mixture, a new type of oscillatory solutal Marangoni instability which is triggered once the stratification has reached a critical value. We experimentally explore the parameter space spanned by the stratification strength and the drop size and theoretically explain the observed crossover from levitating to bouncing by balancing the advection and diffusion around the drop. Finally, the effect of the stable stratification on the Marangoni instability is surprisingly amplified in confined geometries, leading to an earlier onset.
△ Less
Submitted 10 March, 2021; v1 submitted 27 January, 2021;
originally announced January 2021.
-
Plasmonic Microbubble Dynamics in Binary Liquids
Authors:
Xiaolai Li,
Yuliang Wang,
Binglin Zeng,
Marvin Detert,
Andrea Prosperetti,
Harold J. W. Zandvliet,
Detlef Lohse
Abstract:
The growth of surface plasmonic microbubbles in binary water/ethanol solutions is experimentally studied. The microbubbles are generated by illuminating a gold nanoparticle array with a continuous wave laser. Plasmonic bubbles exhibit ethanol concentration-dependent behaviors. For low ethanol concentrations (f_e) of < 67.5%, bubbles do not exist at the solid-liquid interface. For high f_e values o…
▽ More
The growth of surface plasmonic microbubbles in binary water/ethanol solutions is experimentally studied. The microbubbles are generated by illuminating a gold nanoparticle array with a continuous wave laser. Plasmonic bubbles exhibit ethanol concentration-dependent behaviors. For low ethanol concentrations (f_e) of < 67.5%, bubbles do not exist at the solid-liquid interface. For high f_e values of >80%, the bubbles behave as in pure ethanol. Only in an intermediate window of 67.5% < f_e < 80% do we find sessile plasmonic bubbles with a highly nontrivial temporal evolution, in which as a function of time three phases can be discerned. (1) In the first phase, the microbubbles grow, while wiggling. (2) As soon as the wiggling stops, the microbubbles enter the second phase in which they suddenly shrink, followed by (3) a steady reentrant growth phase. Our experiments reveal that the sudden shrinkage of the microbubbles in the second regime is caused by a depinning event of the three phase contact line. We systematically vary the ethanol concentration, laser power, and laser spot size to unravel water recondensation as the underlying mechanism of the sudden bubble shrinkage in phase 2.
△ Less
Submitted 1 January, 2021;
originally announced January 2021.
-
Dynamics of a toroidal bubble on a cylinder surface with an application to geophysical exploration
Authors:
Shuai Li,
Andrea Prosperetti,
Devaraj van der Meer
Abstract:
During the operation of a seismic airgun source, a certain amount of compressed high-pressure air is released from the airgun chamber into the surrounding water, generating an expanding toroidal bubble attached to the airgun-body. The subsequent oscillations of the bubble generate low-frequency pressure waves, which are used to map the ocean subbottom, e.g., to locate oil and gas reserves. The bub…
▽ More
During the operation of a seismic airgun source, a certain amount of compressed high-pressure air is released from the airgun chamber into the surrounding water, generating an expanding toroidal bubble attached to the airgun-body. The subsequent oscillations of the bubble generate low-frequency pressure waves, which are used to map the ocean subbottom, e.g., to locate oil and gas reserves. The bubble dynamic behavior and the emitted pressure waves are inevitably influenced by the airgun-body. However, the bubble-airgun-body interaction is far from well understood. This paper investigates the strong interaction between a long cylinder and an attached toroidal bubble via hundreds of boundary integral simulations, aiming to provide new physical insights for airgun-bubble dynamics. Firstly, the overall physical phenomena are discussed and three types of bubble collapse patterns are identified, namely (i) upward jetting due to gravity, (ii) annular jet toward the cylinder body and (iii) weak/no jet. Thereafter, we investigate the effects of the cylinder radius, initial bubble pressure and Froude number on the bubble oscillation period and the pressure wave induced by the bubble. At last, the impact of a cylinder on a Sercel type airgun-bubble is discussed with a particular focus on the spectrum of the pressure waves.
△ Less
Submitted 8 June, 2020;
originally announced June 2020.
-
Gas-Vapor Interplay in Plasmonic Bubble Shrinkage
Authors:
Mikhail E. Zaytsev,
Yuliang Wang,
Yuhang Zhang,
Guillaume Lajoinie,
Xuehua Zhang,
Andrea Prosperetti,
Harold J. W. Zandvliet,
Detlef Lohse
Abstract:
The understanding of the shrinkage dynamics of plasmonic bubbles formed around metallic nanoparticles immersed in liquid and irradiated by a resonant light source is crucial for the usage of these bubbles in numerous applications. In this paper we experimentally show and theoretically explain that a plasmonic bubble during its shrinkage undergoes two different phases: first, a rapid partial bubble…
▽ More
The understanding of the shrinkage dynamics of plasmonic bubbles formed around metallic nanoparticles immersed in liquid and irradiated by a resonant light source is crucial for the usage of these bubbles in numerous applications. In this paper we experimentally show and theoretically explain that a plasmonic bubble during its shrinkage undergoes two different phases: first, a rapid partial bubble shrinkage governed by vapor condensation and, second, a slow diffusion-controlled bubble dissolution. The history of the bubble formation plays an important role in the shrinkage dynamics during the first phase, as it determines the gas-vapor ratio in the bubble composition. Higher laser powers lead to more vaporous bubbles, while longer pulses and higher dissolved air concentrations lead to more gaseous bubbles. The dynamics of the second phase barely depends on the history of bubble formation, i.e. laser power and pulse duration, but strongly on the dissolved air concentration, which defines the concentration gradient at the bubble interface. Finally, for the bubble dissolution in the second phase, with decreasing dissolved air concentration, we observe a gradual transition from a $R(t) \propto (t_0 - t) ^{1/3}$ scaling law to a $R(t) \propto (t_0 - t) ^{1/2}$ scaling law, where $t_0$ is the lifetime of the bubble and theoretically explain this transition.
△ Less
Submitted 23 April, 2020;
originally announced April 2020.
-
Modelling large scale airgun-bubble dynamics with highly non-spherical features
Authors:
Shuai Li,
Devaraj van der Meer,
A-Man Zhang,
Andrea Prosperetti,
Detlef Lohse
Abstract:
A thorough understanding of the dynamics of meter-sized airgun-bubbles is very crucial to seabed geophysical exploration. In this study, we use the boundary integral method to investigate the highly non-spherical airgun-bubble dynamics and its corresponding pressure wave emission. Moreover, a model is proposed to also consider the process of air release from the airgun port, which is found to be t…
▽ More
A thorough understanding of the dynamics of meter-sized airgun-bubbles is very crucial to seabed geophysical exploration. In this study, we use the boundary integral method to investigate the highly non-spherical airgun-bubble dynamics and its corresponding pressure wave emission. Moreover, a model is proposed to also consider the process of air release from the airgun port, which is found to be the most crucial factor to estimate the initial peak of the pressure wave. The numerical simulations show good agreement with experiments, in terms of non-spherical bubble shapes and pressure waves. Thereafter, the effects of the port opening time $T\rm_{open}$, airgun firing depth, heat transfer, and gravity are numerically investigated. We find that a smaller $T\rm_{open}$ leads to a more violent air release that consequently causes stronger high-frequency pressure wave emissions; however, the low-frequency pressure waves are little affected. Additionally, the non-spherical bubble dynamics is highly dependent on the Froude number $Fr$. Starting from $Fr=2$, as $Fr$ increases, the jet contains lower kinetic energy, resulting in a stronger energy focusing of the bubble collapse itself and thus a larger pressure peak during the bubble collapse phase. For $Fr \ge 7$, the spherical bubble theory becomes an appropriate description of the airgun-bubble. The new findings of this study may provide a reference for practical operations and designing environmentally friendly airguns in the near future.
△ Less
Submitted 6 February, 2020;
originally announced February 2020.
-
A bouncing oil droplet in a stratified liquid and its sudden death
Authors:
Yanshen Li,
Christian Diddens,
Andrea Prosperetti,
Kai Leong Chong,
Xuehua Zhang,
Detlef Lohse
Abstract:
Droplets can self-propel when immersed in another liquid in which a concentration gradient is present. Here we report the experimental and numerical study of a self-propelling oil droplet in a vertically stratified ethanol/water mixture: At first, the droplet sinks slowly due to gravity, but then, before having reached its density matched position, jumps up suddenly. More remarkably, the droplet b…
▽ More
Droplets can self-propel when immersed in another liquid in which a concentration gradient is present. Here we report the experimental and numerical study of a self-propelling oil droplet in a vertically stratified ethanol/water mixture: At first, the droplet sinks slowly due to gravity, but then, before having reached its density matched position, jumps up suddenly. More remarkably, the droplet bounces repeatedly with an ever increasing jumping distance, until all of a sudden it stops after about 30 min. We identify the Marangoni stress at the droplet/liquid interface as responsible for the jumping: its strength grows exponentially because it pulls down ethanol-rich liquid, which in turn increases its strength even more. The jumping process can repeat because gravity restores the system. Finally, the sudden death of the jumping droplet is also explained. Our findings have demonstrated a type of prominent droplet bouncing inside a continuous medium with no wall or sharp interface.
△ Less
Submitted 4 December, 2018;
originally announced December 2018.
-
Tribonucleation of bubbles
Authors:
Sander Wildeman,
Henri Lhuissier,
Chao Sun,
Detlef Lohse,
Andrea Prosperetti
Abstract:
We report on the nucleation of bubbles on solids that are gently rubbed against each other in a liquid. The phenomenon is found to depend strongly on the material and roughness of the solid surfaces. For a given surface, temperature, and gas content, a trail of growing bubbles is observed if the rubbing force and velocity exceed a certain threshold. Direct observation through a transparent solid s…
▽ More
We report on the nucleation of bubbles on solids that are gently rubbed against each other in a liquid. The phenomenon is found to depend strongly on the material and roughness of the solid surfaces. For a given surface, temperature, and gas content, a trail of growing bubbles is observed if the rubbing force and velocity exceed a certain threshold. Direct observation through a transparent solid shows that each bubble in the trail results from the early coalescence of several microscopic bubbles, themselves detaching from microscopic gas pockets forming between the solids. From a detailed study of the wear tracks, with atomic force and scanning electron microscopy imaging, we conclude that these microscopic gas pockets originate from a local fracturing of the surface asperities, possibly enhanced by chemical reactions at the freshly created surfaces. Our findings will be useful either for preventing undesired bubble formation or, on the contrary, for "writing with bubbles," i.e., creating controlled patterns of microscopic bubbles.
△ Less
Submitted 15 April, 2016;
originally announced April 2016.
-
Dynamic Leidenfrost effect: relevant time- and length-scales
Authors:
Minori Shirota,
Michiel A. J. van Limbeek,
Chao Sun,
Andrea Prosperetti,
Detlef Lohse
Abstract:
When a liquid droplet impacts a hot solid surface, enough vapor may be generated under it as to prevent its contact with the solid. The minimum solid temperature for this so-called Leidenfrost effect to occur is termed the Leidenfrost temperature, or the dynamic Leidenfrost temperature when the droplet velocity is non-negligible. We observe the wetting/drying and the levitation dynamics of the dro…
▽ More
When a liquid droplet impacts a hot solid surface, enough vapor may be generated under it as to prevent its contact with the solid. The minimum solid temperature for this so-called Leidenfrost effect to occur is termed the Leidenfrost temperature, or the dynamic Leidenfrost temperature when the droplet velocity is non-negligible. We observe the wetting/drying and the levitation dynamics of the droplet impacting on an (isothermal) smooth sapphire surface using high speed total internal reflection imaging, which enables us to observe the droplet base up to about 100 nm above the substrate surface. By this method we are able to reveal the processes responsible for the transitional regime between the fully wetting and the fully levitated droplet as the solid temperature increases, thus shedding light on the characteristic time- and length-scales setting the dynamic Leidenfrost temperature for droplet impact on an isothermal substrate.
△ Less
Submitted 12 February, 2016; v1 submitted 16 November, 2015;
originally announced November 2015.
-
Heat transport in boiling turbulent Rayleigh-Bénard convection
Authors:
Rajaram Lakkaraju,
Richard J. A. M. Stevens,
Paolo Oresta,
Roberto Verzicco,
Detlef Lohse,
Andrea Prosperetti
Abstract:
Boiling is an extremely effective way to promote heat transfer from a hot surface to a liquid due to several mechanisms many of which are not understood in quantitative detail. An important component of the overall process is that the buoyancy of the bubbles compounds with that of the liquid to give rise to a much enhanced natural convection. In this paper we focus specifically on this enhancement…
▽ More
Boiling is an extremely effective way to promote heat transfer from a hot surface to a liquid due to several mechanisms many of which are not understood in quantitative detail. An important component of the overall process is that the buoyancy of the bubbles compounds with that of the liquid to give rise to a much enhanced natural convection. In this paper we focus specifically on this enhancement and present a numerical study of the resulting two-phase Rayleigh-Bénard convection process. We make no attempt to model other aspects of the boiling process such as bubble nucleation and detachment. We consider a cylindrical cell with a diameter equal to its height. The cell base and top are held at temperatures above and below the boiling point of the liquid, respectively. By keeping the temperature difference constant and changing the liquid pressure we study the effect of the liquid superheat in a Rayleigh number range that, in the absence of boiling, would be between $2\times10^6$ and $5\times10^9$. We find a considerable enhancement of the heat transfer and study its dependence on the bubble number, the degree of superheat of the hot cell bottom and the Rayleigh number. The increased buoyancy provided by the bubbles leads to more energetic hot plumes detaching from the hot cell bottom and, as a consequence, the strength of the circulation in the cell is significantly increased. Our results are in general agreement with recent experimental results of Zhong et al., Phys. Rev. Lett. {\bf 102}, 124501 (2009) for boiling Rayleigh-Bénard convection.
△ Less
Submitted 22 December, 2014;
originally announced December 2014.
-
Leidenfrost temperature increase for impacting droplets on carbon-nanofiber surfaces
Authors:
Hrudya Nair,
Hendrik J. J. Staat,
Tuan Tran,
Arie van Houselt,
Andrea Prosperetti,
Detlef Lohse,
Chao Sun
Abstract:
Droplets impacting on a superheated surface can either exhibit a contact boiling regime, in which they make direct contact with the surface and boil violently, or a film boiling regime, in which they remain separated from the surface by their own vapor. The transition from the contact to the film boiling regime depends not only on the temperature of the surface and kinetic energy of the droplet, b…
▽ More
Droplets impacting on a superheated surface can either exhibit a contact boiling regime, in which they make direct contact with the surface and boil violently, or a film boiling regime, in which they remain separated from the surface by their own vapor. The transition from the contact to the film boiling regime depends not only on the temperature of the surface and kinetic energy of the droplet, but also on the size of the structures fabricated on the surface. Here we experimentally show that surfaces covered with carbon-nanofibers delay the transition to film boiling to much higher temperature compared to smooth surfaces. We present physical arguments showing that, because of the small scale of the carbon fibers, they are cooled by the vapor flow just before the liquid impact, thus permitting contact boiling up to much higher temperatures than on smooth surfaces. We also show that, as long as the impact is in the film boiling regime, the spreading factor of impacting droplets follows the same $\We^{3/10}$ scaling (with $\We$ the Weber number) found for smooth surfaces, which is caused by the vapor flow underneath the droplet.
△ Less
Submitted 3 September, 2013;
originally announced September 2013.
-
Growing bubbles in a slightly supersaturated liquid solution
Authors:
Oscar R. Enríquez,
Christian Hummelink,
Gert-Wim Bruggert,
Detlef Lohse,
Andrea Prosperetti,
Devaraj van der Meer,
Chao Sun
Abstract:
We have designed and constructed an experimental system to study gas bubble growth in slightly supersatu- rated liquids. This is achieved by working with carbon dioxide dissolved in water, pressurized at a maximum of 1 MPa and applying a small pressure drop from saturation conditions. Bubbles grow from hydrophobic cavities etched on silicon wafers, which allows us to control their number and posit…
▽ More
We have designed and constructed an experimental system to study gas bubble growth in slightly supersatu- rated liquids. This is achieved by working with carbon dioxide dissolved in water, pressurized at a maximum of 1 MPa and applying a small pressure drop from saturation conditions. Bubbles grow from hydrophobic cavities etched on silicon wafers, which allows us to control their number and position. Hence, the experiment can be used to investigate the interaction among bubbles growing in close proximity when the main mass transfer mechanism is diffusion and there is a limited availability of the dissolved species.
△ Less
Submitted 24 May, 2013;
originally announced May 2013.
-
Taming Acoustic Cavitation
Authors:
David Fernandez Rivas,
Bram Verhaagen,
Oscar R. Enriquez,
Michel Versluis,
Andrea Prosperetti,
Han Gardeniers,
Detlef Lohse
Abstract:
In this fluid dynamics video we show acoustic cavitation occurring from pits etched on a silicon surface. By immersing the surface in a liquid, gas pockets are entrapped in the pits which upon ultrasonic insonation, are observed to shed cavitation bubbles. Modulating the driving pressure it is possible to induce different behaviours based on the force balance that determines the interaction among…
▽ More
In this fluid dynamics video we show acoustic cavitation occurring from pits etched on a silicon surface. By immersing the surface in a liquid, gas pockets are entrapped in the pits which upon ultrasonic insonation, are observed to shed cavitation bubbles. Modulating the driving pressure it is possible to induce different behaviours based on the force balance that determines the interaction among bubbles and the silicon surface. This system can be used for several applications like sonochemical water treatment, cleaning of surfaces with deposited materials such as biofilms.
△ Less
Submitted 12 October, 2012;
originally announced October 2012.
-
Efficient Sonochemistry through Microbubbles Generated with Micromachined Surfaces
Authors:
David Fernandez Rivas,
Andrea Prosperetti,
Aaldert G. Zijlstra,
Detlef Lohse,
Han J. G. E. Gardeniers
Abstract:
Sonochemical reactors are used in water treatment, the synthesis of fine chemicals, pharmaceutics and others. The low efficiency of sonoreactors have prevented its massive usage at industrial scales. Controlling the appearance of bubbles in place and time is the most limiting factor. A novel type of sonochemical reactor was designed making use of micro-fabrication techniques to control the nucleat…
▽ More
Sonochemical reactors are used in water treatment, the synthesis of fine chemicals, pharmaceutics and others. The low efficiency of sonoreactors have prevented its massive usage at industrial scales. Controlling the appearance of bubbles in place and time is the most limiting factor. A novel type of sonochemical reactor was designed making use of micro-fabrication techniques to control the nucleation sites of micro-bubbles. The efficiency was increased first by locating the nucleation sites in the most active region of a micro-chamber; additionally the desired chemical effect was significantly higher at the same powers than when not controlled. Silicon substrates were micromachined with "artificial nucleation sites" or pits, and placed at the bottom of the micro-chamber. The pits entrap gas which, upon ultrasonic excitation, sheds off a stream of microbubbles. The gas content of the pits is not depleted but is replenished by diffusion and the emission of microbubbles can continue for hours.
△ Less
Submitted 3 August, 2012;
originally announced August 2012.
-
Oscillations of a gas pocket on a liquid-covered solid surface
Authors:
Hanneke Gelderblom,
Aaldert G. Zijlstra,
Leen van Wijngaarden,
Andrea Prosperetti
Abstract:
The dynamic response of a gas bubble entrapped in a cavity on the surface of a submerged solid subject to an acoustic field is investigated in the linear approximation. We derive semi-analytical expressions for the resonance frequency, damping and interface shape of the bubble. For the liquid phase, we consider two limit cases: potential flow and unsteady Stokes flow. The oscillation frequency and…
▽ More
The dynamic response of a gas bubble entrapped in a cavity on the surface of a submerged solid subject to an acoustic field is investigated in the linear approximation. We derive semi-analytical expressions for the resonance frequency, damping and interface shape of the bubble. For the liquid phase, we consider two limit cases: potential flow and unsteady Stokes flow. The oscillation frequency and interface shape are found to depend on two dimensionless parameters: the ratio of the gas stiffness to the surface tension stiffness, and the Ohnesorge number, representing the relative importance of viscous forces. We perform a parametric study and show, among others, that an increase in the gas pressure or a decrease in the surface tension leads to an increase in the resonance frequency until an asymptotic value is reached.
△ Less
Submitted 17 December, 2012; v1 submitted 29 June, 2012;
originally announced June 2012.
-
Highly focused supersonic microjets: numerical simulations
Authors:
Ivo R. Peters,
Yoshiyuki Tagawa,
Nikolai Oudalov,
Chao Sun,
Andrea Prosperetti,
Detlef Lohse,
Devaraj van der Meer
Abstract:
By focusing a laser pulse inside a capillary partially filled with liquid, a vapour bubble is created which emits a pressure wave. This pressure wave travels through the liquid and creates a fast, focused axisymmetric microjet when it is reflected at the meniscus. We numerically investigate the formation of this microjet using axisymmetric boundary-integral simulations, where we model the pressure…
▽ More
By focusing a laser pulse inside a capillary partially filled with liquid, a vapour bubble is created which emits a pressure wave. This pressure wave travels through the liquid and creates a fast, focused axisymmetric microjet when it is reflected at the meniscus. We numerically investigate the formation of this microjet using axisymmetric boundary-integral simulations, where we model the pressure wave as a pressure pulse applied on the bubble. We find a good agreement between the simulations and experimental results in terms of the time evolution of the jet and on all parameters that can be compared directly. We present a simple analytical model that accurately predicts the velocity of the jet after the pressure pulse and its maximum velocity.
△ Less
Submitted 27 September, 2012; v1 submitted 22 March, 2012;
originally announced March 2012.
-
Highly focused supersonic microjets
Authors:
Yoshiyuki Tagawa,
Nikolai Oudalov,
Claas Willem Visser,
Ivo R. Peters,
Deveraj van der Meer,
Chao Sun,
Andrea Prosperetti,
Detlef Lohse
Abstract:
The paper describes the production of thin, focused microjets with velocities up to 850 m/s by the rapid vaporization of a small mass of liquid in an open liquid-filled capillary. The vaporization is caused by the absorption of a low-energy laser pulse. A likely explanation of the observed phenomenon is based on the impingement of the shock wave caused by the nearly-instantaneous vaporization on t…
▽ More
The paper describes the production of thin, focused microjets with velocities up to 850 m/s by the rapid vaporization of a small mass of liquid in an open liquid-filled capillary. The vaporization is caused by the absorption of a low-energy laser pulse. A likely explanation of the observed phenomenon is based on the impingement of the shock wave caused by the nearly-instantaneous vaporization on the free surface of the liquid. An experimental study of the dependence of the jet velocity on several parameters is conducted, and a semi-empirical relation for its prediction is developed. The coherence of the jets, their high velocity and good reproducibility and controllability are unique features of the system described. A possible application is to the development of needle-free drug injection systems which are of great importance for global health care.
△ Less
Submitted 27 April, 2012; v1 submitted 12 December, 2011;
originally announced December 2011.
-
Spatial distribution of heat flux and fluctuations in turbulent Rayleigh-Bénard convection
Authors:
Rajaram Lakkaraju,
Richard. J. A. M. Stevens,
Roberto Verzicco,
Siegfried Grossmann,
Andrea Prosperetti,
Chao Sun,
Detlef Lohse
Abstract:
We numerically investigate the radial dependence of the velocity and temperature fluctuations and of the time-averaged heat flux $\bar{j}(r)$ in a cylindrical Rayleigh-Bénard cell with aspect ratio Γ=1 for Rayleigh numbers Ra between $2 \times 10^6$ and $2\times 10^{9}$ at a fixed Prandtl number Pr = 5.2. The numerical results reveal that the heat flux close to the sidewall is larger than in the c…
▽ More
We numerically investigate the radial dependence of the velocity and temperature fluctuations and of the time-averaged heat flux $\bar{j}(r)$ in a cylindrical Rayleigh-Bénard cell with aspect ratio Γ=1 for Rayleigh numbers Ra between $2 \times 10^6$ and $2\times 10^{9}$ at a fixed Prandtl number Pr = 5.2. The numerical results reveal that the heat flux close to the sidewall is larger than in the center and that, just as the global heat transport, it has an effective power law dependence on the Rayleigh number, $\bar{j}(r)\propto Ra^{γ_j(r)}$. The scaling exponent $γ_j(r)$ decreases monotonically from 0.43 near the axis ($r \approx 0$) to 0.29 close to the side walls ($r \approx D/2$). The effective exponents near the axis and the side wall agree well with the measurements of Shang et al. (Phys.\ Rev.\ Lett.\ \textbf{100}, 244503, 2008) and the predictions of Grossmann and Lohse (Phys.\ Fluids \textbf{16}, 1070, 2004). Extrapolating our results to large Rayleigh number would imply a crossover at $Ra\approx 10^{15}$, where the heat flux near the axis would begin to dominate. In addition, we find that the local heat flux is more than twice as high at the location where warm or cold plumes go up or down, than in the plume depleted regions.
△ Less
Submitted 16 April, 2012; v1 submitted 2 December, 2011;
originally announced December 2011.
-
Drop impact on superheated surfaces
Authors:
Tuan Tran,
Hendrik J. J. Staat,
Andrea Prosperetti,
Chao Sun,
Detlef Lohse
Abstract:
At impact of a liquid droplet on a smooth surface heated above the liquid's boiling point, the droplet either immediately boils when it contacts the surfaces (``contact boiling''), or without any surface contact forms a Leidenfrost vapor layer towards the hot surface and bounces back (``gentle film boiling''), or both forms the Leidenfrost layer and ejects tiny droplets upward (``spraying film boi…
▽ More
At impact of a liquid droplet on a smooth surface heated above the liquid's boiling point, the droplet either immediately boils when it contacts the surfaces (``contact boiling''), or without any surface contact forms a Leidenfrost vapor layer towards the hot surface and bounces back (``gentle film boiling''), or both forms the Leidenfrost layer and ejects tiny droplets upward (``spraying film boiling''). We experimentally determine conditions under which impact behaviors in each regime can be realized. We show that the dimensionless maximum spreading $γ$ of impacting droplets on the heated surfaces in both gentle and spraying film boiling regimes shows a universal scaling with the Weber number $\We$ ($γ\sim\We^{2/5}$) -- regardless of surface temperature and of liquid properties -- which is much steeper than for the impact on non-heated (hydrophilic or hydrophobic) surfaces ($γ\sim\We^{1/4}$). We also intereferometrically measure the vapor thickness under the droplet.
△ Less
Submitted 2 November, 2011;
originally announced November 2011.
-
Improved procedure for the computation of Lamb's coefficients in the Physalis method for particle simulation
Authors:
Kristjan Gudmundsson,
Andrea Prosperetti
Abstract:
The Physalis method is suitable for the simulation of flows with suspended spherical particles. It differs from standard immersed boundary methods due to the use of a local spectral representation of the solution in the neighborhood of each particle, which is used to bridge the gap between the particle surface and the underlying fixed Cartesian grid. This analytic solution involves coefficients wh…
▽ More
The Physalis method is suitable for the simulation of flows with suspended spherical particles. It differs from standard immersed boundary methods due to the use of a local spectral representation of the solution in the neighborhood of each particle, which is used to bridge the gap between the particle surface and the underlying fixed Cartesian grid. This analytic solution involves coefficients which are determined by matching with the finite-difference solution farther away from the particle. In the original implementation of the method this step was executed by solving an over-determined linear system via the singular-value decomposition. Here a more efficient method to achieve the same end is described. The basic idea is to use scalar products of the finite-difference solutions with spherical harmonic functions taken over a spherical surface concentric with the particle. The new approach is tested on a number of examples and is found to posses a comparable accuracy to the original one, but to be significantly faster and to require less memory. An unusual test case that we describe demonstrates the accuracy with which the method conserves the fluid angular momentum in the case of a rotating particle.
△ Less
Submitted 8 September, 2011;
originally announced September 2011.
-
Nucleation threshold and deactivation mechanisms of nanoscopic cavitation nuclei
Authors:
Bram M. Borkent,
Stephan Gekle,
Andrea Prosperetti,
Detlef Lohse
Abstract:
The acoustic nucleation threshold for bubbles trapped in cavities has theoretically been predicted within the crevice theory by Atchley & Prosperetti [J. Acoust. Soc. Am. 86, 1065-1084 (1989)]. Here, we determine this threshold experimentally, by applying a single pressure pulse to bubbles trapped in cylindrical nanoscopic pits ("artificial crevices") with radii down to 50 nm. By decreasing the…
▽ More
The acoustic nucleation threshold for bubbles trapped in cavities has theoretically been predicted within the crevice theory by Atchley & Prosperetti [J. Acoust. Soc. Am. 86, 1065-1084 (1989)]. Here, we determine this threshold experimentally, by applying a single pressure pulse to bubbles trapped in cylindrical nanoscopic pits ("artificial crevices") with radii down to 50 nm. By decreasing the minimum pressure stepwise, we observe the threshold for which the bubbles start to nucleate. The experimental results are quantitatively in excellent agreement with the theoretical predictions of Atchley & Prosperetti. In addition, we provide the mechanism which explains the deactivation of cavitation nuclei: gas diffusion together with an aspherical bubble collapse. Finally, we present superhydrophobic nuclei which cannot be deactivated, unless with a high-speed liquid jet directed into the pit.
△ Less
Submitted 2 June, 2009;
originally announced June 2009.
-
Heat transfer mechanisms in bubbly Rayleigh-Benard convection
Authors:
Paolo Oresta,
Roberto Verzicco,
Detlef Lohse,
Andrea Prosperetti
Abstract:
The heat transfer mechanism in Rayleigh-Benard convection in a liquid with a mean temperature close to its boiling point is studied through numerical simulations with point-like vapor bubbles, which are allowed to grow or shrink through evaporation and condensation and which act back on the flow both thermally and mechanically. It is shown that the effect of the bubbles is strongly dependent on…
▽ More
The heat transfer mechanism in Rayleigh-Benard convection in a liquid with a mean temperature close to its boiling point is studied through numerical simulations with point-like vapor bubbles, which are allowed to grow or shrink through evaporation and condensation and which act back on the flow both thermally and mechanically. It is shown that the effect of the bubbles is strongly dependent on the ratio of the sensible heat to the latent heat as embodied in the Jacob number Ja. For very small Ja the bubbles stabilize the flow by absorbing heat in the warmer regions and releasing it in the colder regions. With an increase in Ja, the added buoyancy due to the bubble growth destabilizes the flow with respect to single-phase convection and considerably increases the Nusselt number.
△ Less
Submitted 12 November, 2008;
originally announced November 2008.
-
A note on the effective slip properties for microchannel flows with ultra-hydrophobic surfaces
Authors:
Mauro Sbragaglia,
Andrea Prosperetti
Abstract:
A type of super-hydrophobic surface consists of a solid plane boundary with an array of grooves which, due to the effect of surface tension, prevent a complete wetting of the wall. The effect is greatest when the grooves are aligned with the flow. The pressure difference between the liquid and the gas in the grooves causes a curvature of the liquid surface resisted by surface tension. The effect…
▽ More
A type of super-hydrophobic surface consists of a solid plane boundary with an array of grooves which, due to the effect of surface tension, prevent a complete wetting of the wall. The effect is greatest when the grooves are aligned with the flow. The pressure difference between the liquid and the gas in the grooves causes a curvature of the liquid surface resisted by surface tension. The effects of this surface deformation are studied in this paper. The corrections to the effective slip length produced by the curvature are analyzed theoretically and a comparison with available data and related mathematical models is presented.
△ Less
Submitted 4 November, 2006;
originally announced November 2006.
-
Effective velocity boundary condition at a mixed slip surface
Authors:
M. Sbragaglia,
A. Prosperetti
Abstract:
This paper studies the nature of the effective velocity boundary conditions for liquid flow over a plane boundary on which small free-slip islands are randomly distributed. It is found that, to lowest order in the area fraction $β$ covered by free-slip regions with characteristic size $a$, a macroscopic Navier-type slip condition emerges with a slip length of the order of $aβ$. The study is moti…
▽ More
This paper studies the nature of the effective velocity boundary conditions for liquid flow over a plane boundary on which small free-slip islands are randomly distributed. It is found that, to lowest order in the area fraction $β$ covered by free-slip regions with characteristic size $a$, a macroscopic Navier-type slip condition emerges with a slip length of the order of $aβ$. The study is motivated by recent experiments which suggest that gas nano-bubbles may form on solid walls and may be responsible for the appearance of a partial slip boundary conditions for liquid flow. The results are also relevant for ultra-hydrophobic surfaces exploiting the so-called ``lotus effect''.
△ Less
Submitted 1 July, 2006;
originally announced July 2006.
-
Giant bubble pinch-off
Authors:
Raymond Bergmann,
Devaraj van der Meer,
Mark Stijnman,
Marijn Sandtke,
Andrea Prosperetti,
Detlef Lohse
Abstract:
Self-similarity has been the paradigmatic picture for the pinch-off of a drop. Here we will show through high-speed imaging and boundary integral simulations that the inverse problem, the pinch-off of an air bubble in water, is not self-similar in a strict sense: A disk is quickly pulled through a water surface, leading to a giant, cylindrical void which after collapse creates an upward and a do…
▽ More
Self-similarity has been the paradigmatic picture for the pinch-off of a drop. Here we will show through high-speed imaging and boundary integral simulations that the inverse problem, the pinch-off of an air bubble in water, is not self-similar in a strict sense: A disk is quickly pulled through a water surface, leading to a giant, cylindrical void which after collapse creates an upward and a downward jet. Only in the limiting case of large Froude number the neck radius $h$ scales as $h(-\log h)^{1/4} \propto τ^{1/2}$, the purely inertial scaling. For any finite Froude number the collapse is slower, and a second length-scale, the curvature of the void, comes into play. Both length-scales are found to exhibit power-law scaling in time, but with different exponents depending on the Froude number, signaling the non-universality of the bubble pinch-off.
△ Less
Submitted 24 January, 2006;
originally announced January 2006.