Abstract
The application of magnesium in the automotive industry contributes to reduced fuel consumption and CO2 emissions. Nowadays, most magnesium components in automobiles are manufactured by die casting. In this paper, simulation of the low pressure die casting process of a magnesium wheel that adopts FDM (finite difference method) is presented. Through calculating the temperature and velocity fields during filling and solidification stages, the evolution of temperature and liquid fraction is analyzed. Then, potential defects including gas pores in the middle of the spokes, shrinkage at the top of the rim and the rim/spokes junctions are predicted. The reasons for these defects are also analyzed and the solutions to eliminate them are presented. The air gas pores and shrinkage at the top of the rim are eliminated effectively by reducing the pouring velocity. Furthermore, the cooling capacity at the rim/spokes junctions is also investigated in the paper. Through analysis of the shrinkage defects generated in various cooling modes, it is proven that the cooling pipe system set in the side mould alone is a valid way to enhance the cooling capacity at the rim/spoke junction areas. Finally, the strength analysis is carried out for further verification of the effectiveness of the new cooling method.
Similar content being viewed by others
References
Schumann S, Friedrich H (2003) Current and future use of magnesium in the automobile industry. Mate Sci Forum 419:51–56
Robert E (2001) Magnesium alloys and their applications. Light Met Age 5:54–56
Benedyk JC (2001) 58th annual world magnesium conference: automotive, environmental, supply/demand, and quality developments. Light Met Age 7:103–106
Mirbagheri SMH, Esmaeileian H, Serajzadeh S, Varahram N, Davami P (2003) Simulation of melt flow in coated mould cavity in the casting process. J Mater Process Technol 142:493–507
Chow WK (1996) Application of computational fluid dynamics in building services engineering. Build Environ 5:425–436
Katzarova IH, Arsova YB, Stoyanovb P, Zeunerb T, Buehrig-Polaczekb A, Sahmb PR (2001) Porosity formation in axi-symmetric castings produced by counter-pressure casting method. Int J Heat Mass Tran 44:111–119
Katzarov IH (1999) Finite element method for simulation of 3-D form filling with incompressible fluid. Int J Heat Mass Tran 42:3331–3336
Zhang YF, Liu WK, Wang HP (1995) Casing filling simulations of thin-walled cavities. Comp Meth Appl Mech Eng 128:199–230
Shepel SV, Paolucci S (2002) Numerical simulation of filling and solidification of permanent mold castings. Appl Therm Eng 22:229–248
Dahle AK, Sannes SS, John DH, Westengen H (2001) Formation of defect bands in high pressure die cast magnesium alloys. J Light Metals 2:99–103
Wang QG, Apelian D, Lados DA (2001) Fatigue behavior of A356-T6 aluminum cast alloys. Part I, effect of casting defects. J Light Metals 1:73–84
Nadot Y, Mendez J, Ranganathan N (2004) Influence of casting defects on the fatigue limit of nodular cast iron. Int J Fatigue 3:311–319
Avalle M, Belingardi G, Cavatorta MP, Doglione R (2002) Casting defects and fatigue strength of a die cast aluminium alloy: a comparison between standard specimens and production components. Int J Fatigue 1:1–9
Acknowledgement
The authors would like to acknowledge financial support of the National High-Tech Research and Development Program of China (863 Program) (grant No. 2002AA331120).
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Wang, Yc., Li, Dy., Peng, Yh. et al. Numerical simulation of low pressure die casting of magnesium wheel. Int J Adv Manuf Technol 32, 257–264 (2007). https://doi.org/10.1007/s00170-005-0325-1
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-005-0325-1