Rectificadores Controlados

SC6006: Operation Manual
N T S R G1 K1 G2 K2 G3 K3 G4 K4 G5 K5 G6 K6
SEMICODE
ELECTRONICA
®
PWR
SC6006
LCD CONTRAST
FIRING
FAULT
OV CURR
EXT BLK
MENU OK
RESET
COARSE FINE
U_SENS I_SENS I_SET U_SET I_SENS U_SENS ALPHA
SC6006
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
130320 Rev.:2.4
Index of contents
1 GENERAL.................................................................................................................................................... 4
1.1 Special Features................................................................................................................................... 4
1.2 Warranty............................................................................................................................................... 4
2 SAFETY INSTRUCTIONS............................................................................................................................ 5
2.1 Operator and personnel requirements.................................................................................................. 5
2.2 Proper and intended use...................................................................................................................... 5
2.3 Use and operation of the device........................................................................................................... 5
3 FUNCTIONS................................................................................................................................................. 6
3.1 Topology configuration.......................................................................................................................... 6
3.2 Operating modes.................................................................................................................................. 6
3.3 Setpoint signals processing.................................................................................................................. 9
3.3.1 Analog or digital references / setpoints.........................................................................................9
3.3.2 Setpoints signal processing diagrams.......................................................................................... 9
3.4 Feedback signals processing.............................................................................................................. 11
3.5 Setpoints and feedback live input signals configuration.....................................................................12
3.6 Control Modes.................................................................................................................................... 12
3.7 Soft power ON and soft power OFF................................................................................................... 13
3.8 Fault sources and pulse inhibition...................................................................................................... 14
3.9 Start up mode..................................................................................................................................... 15
3.10 Autoset function................................................................................................................................ 15
3.11 Output assignation option................................................................................................................. 16
3.12 Saving all the changes and configurations.......................................................................................16
3.13 Restore default configurations.......................................................................................................... 16
4 SETTINGS AND OPERATION................................................................................................................... 17
4.1 PCB connectors overview................................................................................................................... 17
4.2 Connectors......................................................................................................................................... 18
4.2.1 Power supply connector (J1)...................................................................................................... 18
4.2.2 Synchronism connector (J11)..................................................................................................... 18
4.2.3 Feedback voltage signal connector (J12)...................................................................................19
4.2.4 External block and dry output fault connector (J13)....................................................................19
4.2.5 Current input feedback connector (J14).....................................................................................20
4.2.6 Setpoints and inhibit connector (J15)......................................................................................... 21
4.2.7 Feedback and alpha setpoint input connector (J16)...................................................................22
4.2.8 Output SCR firing connectors (SCR1-SCR6).............................................................................23
4.2.9 Serial communications DB-9 connector (J32).............................................................................23
4.3 LCD menu settings and navigation..................................................................................................... 24
4.3.1 Main Menu:................................................................................................................................. 24
4.3.1.1 LCD contrast adjusting potentiometer................................................................................25
4.3.1.2 LCD backlight..................................................................................................................... 25
4.3.2 Settings menu............................................................................................................................. 25
4.3.2.1 Topology option.................................................................................................................. 25
4.3.2.2 Mode option........................................................................................................................ 26
4.3.2.3 Reference submenu........................................................................................................... 26
4.3.2.4 Live-zero input submenu.................................................................................................... 26
4.3.2.5 Control option..................................................................................................................... 26
4.3.2.6 Soft ON/OFF ramps submenu............................................................................................ 26
4.3.2.7 Faults submenu.................................................................................................................. 27
4.3.2.8 Start up option.................................................................................................................... 27
4.3.2.9 Autoset options submenu................................................................................................... 28
4.3.2.10 Outputs assignation submenu.......................................................................................... 28
4.3.2.11 Communications submenu............................................................................................... 28
4.3.2.12 Save changes option........................................................................................................ 28
4.3.2.13 Restore option.................................................................................................................. 29
4.3.3 Registers menu.......................................................................................................................... 29
4.3.4 Debug menu............................................................................................................................... 30
4.4 Jumpers and DIP Switches configurations......................................................................................... 30
2
4.4.1 Jumpers J7 and J20 to J24........................................................................................................ 30
4.4.2 DIP Switches.............................................................................................................................. 31
4.4.3 Setting the gain for direct voltage feedback input.......................................................................32
4.5 LED Indications.................................................................................................................................. 32
5 SERIAL COMMUNICATION....................................................................................................................... 33
5.1 Overview available command set....................................................................................................... 34
5.2 Query instruction set........................................................................................................................... 34
5.2.1 “?ver” query version command................................................................................................... 34
5.2.2 “?S” query status register........................................................................................................... 34
5.2.3 “?A” query alpha register............................................................................................................ 34
5.2.4 “?U” query voltage register......................................................................................................... 34
5.2.5 “?I” query current register........................................................................................................... 34
5.3 Signal instruction set.......................................................................................................................... 34
5.3.1 “*OK” signal command............................................................................................................... 35
5.3.2 “*MENU” signal command.......................................................................................................... 35
5.3.3 “*UP” signal command................................................................................................................ 35
5.3.4 “*DW” signal command............................................................................................................... 35
5.3.5 “*RMT” signal command............................................................................................................. 35
5.3.6 “*ECHO” signal command.......................................................................................................... 35
5.3.7 “*HOME” signal command.......................................................................................................... 35
5.3.8 “*RST” signal command............................................................................................................. 35
5.3.9 “*SV” signal command................................................................................................................ 35
5.4 Memory read instruction..................................................................................................................... 36
5.5 Memory write instruction..................................................................................................................... 36
6 INTERNAL MEMORY AND REGISTERS................................................................................................... 37
6.1 Readable registers............................................................................................................................. 37
6.1.1 status registers........................................................................................................................... 37
6.1.2 p_status registers....................................................................................................................... 38
6.2 Writable registers................................................................................................................................ 40
7 INSTALLATION........................................................................................................................................... 41
7.1 Typical application circuits.................................................................................................................. 41
7.2 Control AC/AC applications................................................................................................................ 41
7.2.1 W3C topology connection example............................................................................................ 41
7.2.2 W3C current and voltage feedback scheme...............................................................................42
7.2.3 Load connection types for W3C scheme....................................................................................42
7.2.4 M6CK and M3.2CK schemes of connection...............................................................................43
7.3 Control AC/DC applications. B6C scheme.......................................................................................... 44
7.3.1 B6C topology connection example............................................................................................. 44
7.3.2 DC current sense feedback using a shunt..................................................................................44
7.3.3 Feedback using a current and voltage isolated sensors.............................................................45
7.4 Direct drive mode with block signal.................................................................................................... 46
7.5 Mounting recommendations............................................................................................................... 48
7.5.1 General mounting recommendations.......................................................................................... 48
7.5.2 Recommended start up procedure............................................................................................. 48
7.5.3 Notes about the control card in systems controlled by microcontrollers or PLC.........................49
8 AVAILABLE ACCESSORIES...................................................................................................................... 50
8.1 SCRP6006.......................................................................................................................................... 50
8.1.1 Interfacing SC6006 with remote panel SCRP6006.....................................................................50
8.2 SCGI24............................................................................................................................................... 51
8.2.1 Galvanically isolated current loop with shunt using SCGI24.......................................................51
8.3 SCST700............................................................................................................................................ 52
8.3.1 Obtaining a neutral reference using SCST700 for improved synchronism aquisition.................52
9 FIRMWARE REVISIONS............................................................................................................................ 53
10 TECHNICAL SPECIFICATIONS............................................................................................................... 54
10.1 Mechanical dimensions.................................................................................................................... 58
10.2 Connectors overview........................................................................................................................ 58
3
1 GENERAL
These operation instructions describe the configuration and functions of the SC6006 and are designed to
enable qualified personnel to perform the planning, commissioning and maintenance of this equipment.
These operation instructions comply with the current technical specifications of the device at the time of
publication. The contents do not constitute a subject matter of the contract, but serve for information
purposes only.
We reserve the right to alter any specification given in these operating instructions, especially with regard to
technical data and operation. SEMICODE reserves the right to make modifications with regard to the content
and technical data in these operation instructions.
Versatility and ruggedness are the main features of SC6006 providing a lot of regulation options and a great
performance in many different applications and environments.
SC6006 is designed to adapt to most common rectification and control schemes, like W3C, B6C, M6C and
M3.2C. Optionally can also be applied to W3H, B6H and M3C. The power adjustment can be made by
current or voltage through potentiometers or by external analog signals. SC6006 also has protection against
current peaks, soft start up ramp, inhibit input by external relay, possibility of a shunt terminal + or -, current
transformer direct input, etc.
The SC6006 is also a communication-capable thyristor power controller. It can be used wherever alternating
voltages, alternating currents or outputs in thermal process technology e.g. need to be controlled. Main
applications for this circuit are those where is needed a safe control for large currents through thyristors, for
example thermal process, surfaced treatments, electrolytic process, ovens, lightning, etc.
1.1 Special Features

• Wide voltage range for supply the entire system up to 480 VAC.
• High SCR voltage applications up to 700 VAC.
• Soft start and soft stop .
• Autoset mode. Automatic sync, rotation and output assignation.
• Operating modes: phase regulation, burst regulation,relay mode or 6 independent SCR drivers.
• Open-loop or closed-loop with U and I control modes.
• Connectivity and system control through RS-232 interface.
1.2 Warranty
In the event of any claims in connection with the SC6006, please contact us quoting:
• Fabrication number / serial number.
• Reason for the complaint.
• Environmental conditions of the device.
• Operating mode.
• Period of use.
Goods and services are subject to the general conditions of supply for products of the electrical industry, and our general sales
conditions.
Claims in connection with supplied goods must be submitted within one week of receip, along with the delivery note. SEMICODE Will
rescind all obligations such as warranty agreements, service contacts, etc. entered into by SEMICODE Or its representatives without
prior notice if maintenance and repair work is carried out using anything other than original SEMICODE spare parts or spare parts
purchased from SEMICODE
4
2 SAFETY INSTRUCTIONS
The safety instructions and operating manual are to be carefully read prior to installation and
commissioning
2.1 Operator and personnel requirements

The operator must ensure the following:
• The safety regulations of the operating instructions are observed.
• The accident prevention regulations valid in the respective country of use and general, national and
regional safety regulations are observed.
• The operating conditions and restrictions resulting from the technical data are observed.
• Only qualified electro-technical personnel who are familiar with the pertinent safety and installation
regulations may perform the connection installation testing and operation of the device.
• This operating instructions must be read carefully prior to the installation and initial start-up.
2.2 Proper and intended use

• SC6006 SCR power controller is a component which may only be used for control and regulation of
electrical energy.
• It is not permitted to make any unauthorized modifications to the unit or to use any spare parts or
replacements parts not approved by SEMICODE, or to use the unit for any other purpose.
• The device is a component that cannot function alone.
• The Thyristor Power Controller may at most be operated between the maximum admissible ranges
specified by its datasheet.
• The Thyristor Power Controller may only be operated in connection with a suitable and series
connected power supply disconnecting device.
• As a component, the SC6006 SCR controller is unable to operate alone and must be projected for its
intended use to minimize residual risks.
• Despite proper use, it is possible in the event of fault, that the device will not control the currents,
voltages and power in the load circuit, the following reactions are possible: current interrupted, half
wave operation, permanent flow of power.
2.3 Use and operation of the device

• Only power on the mains voltage at the device when there is no danger to persons, system or load.
• Protect the device against dust and damp.
• Install the device in a upright or flat position and ensure a minimum ventilation distance between
surroundings.
• If mounted in a cabinet ensure sufficient ventilation.
• Observe minimum spacing (clearance: 150 mm above and below).
• Ground the device in accordance with local regulations.
• Connect the device with the power stack and load in accordance with the connection diagrams.
• The device is configured and calibrated when delivered with standard parameters. Check default
settings and adjust them to the application conditions if necessary (e.g. operating mode, control
mode, monitoring, faults, etc.)
5
3 FUNCTIONS
In order to adapt as best as possible to a wide range of applications SC6006 has numerous functions which
had to be properly configured before its use along with a SCR power stack. All the functions available and its
proper configuration are described in the following chapter.
3.1 Topology configuration

SC6006 has 2 topology configurations: B6C and W3C. The topology must be configured according the
application and the SCRs power stack topology which will be used.
This option enables or disables a 30º shift in output firing control signal of the SCRs with regard the input
mains phase sync signal in order to properly fire the topology in use. For W3C schemes no phase delay
between the input phase and the triggering pulse is needed, for B6C schemes it is needed a 30º delay to
correctly fire the SCRs.
System firing topology can be configured by software, please refer to chapter 4.3.2.1 in page 25 for a more
detailed explanation for the procedure and check on chapter 7 the topology which must be set on each case
regarding the converter in use.
3.2 Operating modes

SC6006 has 4 different operating modes: PSA (Phase-Shift Angle mode) working as a phase delay switch
controller, FWS (Full Wave Switch mode) working as proportional ON/OFF controller, RLY (Relay mode)
working as 3 independent zero-cross static relays and DRV (Independent multidriver firing mode) working as
6 direct SCR switching drivers.
- Phase-shift angle controller mode (PSA)

In this operating mode, the firing phase of the sinus wave of the mains voltage is shifted. The shift depends
on the setpoint value. In phase angle firing mode the controller fires over a variable portion of the incoming
AC cycle in response to the control input signal. Characteristic of this operating mode are the high control
dynamics but when phase-shift angle control PS is used, harmonics of the mains voltage should be
expected as drawback.
The following image (figure 1) shows an example of PSA waveform according the alpha setpoint going from
0 to full wave switch.
alpha
setpoint
100%
0%
time
PSA
waveform
time
figure 1: PSA waveform example versus alpha setpoint.
6
- Full wave switch mode (FWS)
In FWS operating mode, the mains voltage is switched periodically firing in burst packets of AC waves,
relative to the defined setpoint. Integer multiples of the mains periods are switched to avoid D.C.
components. The operating mode full wave switch principle FWS is particularly suited for loads with a high
thermal inertia.
This mode only works along with alpha set input J15[p12]-ALPHA_INP or D_ALPHA_REG[M011] software
register in open loop and switches packets of 100 semi periods in the zero-cross of the mains, proportionally
to the value of alpha set.
In figure 2 is shown a FWS waveform example according the alpha setpoint. In this image and for sake of
simplicity the wave packets are of 5 periods.
alpha
setpoint
100%
0%
time
FWS
waveform
time
figure 2: FWS waveform example versus alpha setpoint.
When using this mode it is also possible to define a number of periods in which PSA will be applied as an
initializing slope on each packet. Please read a more detailed description of this option on chapter 3.7 -Soft
power ON and soft power OFF.
- Relay mode (RLY)

Relay mode switches the outputs in the next zero-cross event after a triggering signal. When a switching
signal is applied to card's input control, the SCRs will switch when the voltage across its terminals crosses
the 0 V. The switch off is produced naturally when the control signal is off and the direct current flowing
through SCRs extinguishes.
figure 3: Example of picket fence gate driving.
Using all 6 firing outputs it is possible to implement up to 3 static relays driving an antiparallel SCR power
scheme each. There are available 3 different static relays (one for each phase.) You can configure which
outputs will fire. This mode works as a switch controller for 3 static relays with a W3C topology or as 3
independent static relay firing W1C.
7
Working as a relay mode the inputs voltage setpoint (J15[p15]-U_SETPOINT), current setpoint (J15[p14]-
I_SETPOINT) and alpha setpoint (J16[p21]-ALPHA_INP) works as digital triggering inputs (according to its
configuration: TTL, 0-10 V, 0-20 mA or 4-20mA) and firing the outputs SCR1 & SCR2, SCR3 & SCR4, SCR5
& SCR6 respectively.
System mode of operation can be configured by software, please refer to chapter 4.3.2.2 on page 26 for a
more detailed explanation.
- Independent multidriver firing mode (DRV)

Independent multidrive mode switches the outputs according 6 independent triggering signals. When a
switching signal is applied to card's input control, SC6006 will switch ON the corresponding SCRs gate.
In this mode SC6006 will not sense the mains synchronism and acts just like 6 independent SCR drivers.
Fault signaling due synchronization and overcurrent will be disabled automatically in this operation mode as
well as the inhibit signal working as a source for Halt fault.
In independent multidriver firing mode the inputs current setpoint (J15[p14]-I_SETPOINT), voltage setpoint
(J15[p15]-I_SETPOINT), current measure (J16[p19]-I_SENS), voltage measure(J16[p20]-U_SENS) and
alpha setpoint (J16[p21]-ALPHA_INP) works as digital firing inputs (according to its configuration: TTL, 0-10
V, 0-20 mA or 4-20mA) and firing the outputs SCR1,SCR2, SCR4, SCR5, SCR6 respectively.
Inhibit input (J15[p16]-INHIBIT) works as digital firing CMOS level input for SCR3.
System mode of operation can be configured by software, please refer to chapter 4.3.2.2 on page 26 for a
more detailed explanation. An example of connection is given at chapter 7.4 on page 46.
8
3.3 Setpoint signals processing
There are 3 different analog input setpoints available: voltage setpoint (J15[p15]-U_SETPOINT), current
setpoint (J15[p14]-I_SETPOINT) and alpha setpoint (J16[p21]-ALPHA_INP ), this signals works as external
references which should be provided by the operator or PLC to the controller (SC6006) giving the
corresponding setpoint when regulating the ouptut voltage of the converter, the output current of the
converter or the firing phase angle of the converter respectively.
As mentioned before all these input setpoint signals can be configured to work as 0-5 V or 0-10 V and also
0-20 mA and live input 4-20 mA. This configurations are made using the PCB DIP switches and LCD screen.
Furthermore all this inputs can be digitally overrode. There are 3 software setpoint registers which can be set
by the operator through LCD and push-buttons on board or by using the serial communication port.
3.3.1 Analog or digital references / setpoints

Input signals of current setpoint, voltage setpoint and alpha setpoint for the open or closed loop control can
be configured, independently, as a digital reference or analog reference.
If an input reference is set as digital, its value must be set through software using the on-board LCD menu or
through RS-232 serial communications interface, the following are the corresponding software registers:
alpha_setpoint: D_ALPHA_REG[M011]
u_setpoint: D_VOLTAGE_REG[M034]
i_setpoint: D_CURRENT_REG[M035]
All the digital setpoint are 10 bits registers and can be set with decimal values from 0 to 1023.
Please refer to chapter 5-SERIAL COMMUNICATION for further explanation regarding the communications
interface and communications protocol of the system if it is needed to change this registers remotely.
If an input reference is set as analog the corresponding value is obtained by his assigned PCB input:
alpha_setpoint: J16[p21]-ALPHA_INP
u_setpoint: J15[p15]-U_SETPOINT
i_setpoint: J15[p14]-I_SETPOINT
Note:
All analog setpoint input signals can be configured to work as 0-5 V or 0-10 V and also 0-20 mA. Additionally they can be
interfaced connecting a potentiometer (2 included). The recommended value of this potentiometers is 4.7 kΩ.
Configuration are made using the PCB DIP switches. Please refer to chapter 4.4.2 on page 31 for the DIP-switches
configurations.
Also all inputs can be configured as 4-20 mA (Live Input). The Live Input is enabled through software. Please refer to
chapter 4.3.2.4 on page 26.
3.3.2 Setpoints signal processing diagrams

This chapter provides several simplified diagrams and blocks regarding the different sources of setpoints
available with the aim of clarify the way this setpoints are processed and routed or selected by SC6006.
This diagrams depicts, when necessary, the input impedance or resistive charge for the input signal, the
filtering (low pass) and shaping modules (live input shaping) as well the hardware and software setting which
selects or switchs one or other signal path depending on selected signal source by the operator.
Please take them as a guidance planned for the sake of a more in-depth and comprehensive scheme of the
SC6006 signal path and setpoint signal process.
9
Alpha setpoint signal processing.
In figure 4 is shown the diagram for acquisition and setting of alpha setpoint.
ALPHA_INP
0
J16 21 ADC
0-5V / 0-20mA ALPHA_REG[M005]
U13-A 0-5V / 0-10V : U13-B
J16 18 0-20/4-20mA : Live inp. D_ALPHA_REG[M011] 1
ALPHA: [An / Dig]
figure 4: alpha setpoint signal processing diagram.
By default SC6006 takes the alpha setpoint from the analog ALPHA_INP input configured as 0-5 V DC.
Voltage setpoint signal processing.

In figure 5 is shown the diagram of acquisition and setting of voltage setpoint.
U_SETPOINT
0
J15 15 ADC
0-5V / 0-20mA U_REF_REG[M008]
U11-C 0-5V / 0-10V : U11-D
0-20/4-20mA : Live inp. D_UREF_REG[M012] 1
J15 13
VOLTAGE: [An / Dig]
figure 5: Voltage setpoint signal processing diagram.
By default SC6006 takes the voltage setpoint from the analog U_SETPOINT input configured as 0-5 V DC.
Current setpoint signal processing.

In figure 6 is shown the diagram of acquisition and setting of current setpoint.
I_SETPOINT
0
J15 14 ADC
0-5V / 0-20mA I_REF_REG[M009]
U11-A 0-5V / 0-10V : U11-B
0-20/4-20mA : Live inp. D_IREF_REG[M013] 1
J15 13
CURRENT: [An / Dig]
figure 6: Current setpoint signal processing diagram.
By default SC6006 takes the current setpoint from the analog I_SETPOINT input configured as 0-5 V DC.
10
3.4 Feedback signals processing
SC6006 have 2 independent feedback signals: current feedback signal and voltage feedback signal. This
signals are used when a closed loop control is needed.
As on the previous chapter, following, simplified diagrams are provided regarding the different sources of
feedback signals available with the aim of clarify the way this feedback signals are processed and routed or
selected by SC6006.
Current feedback signal processing.

There are 3 different analogic sources available for the current feedback signal:
• Current transformers: AC currents. The current feedback signal can be obtained directly from
standard 200 mA AC current transformers (J14[p9..11]-I_AUX).
• Shunt: DC currents. By interfacing a standard 60 mV shunt (J14[p12]-I_SHUNT) .
• Analog configurable input: current feedback signal also can be obtained with an analog (0-5 V , 0-10
V, 0-20 mA or 4-20 mA) current signal (J16[p19]-I_SENS).
I_SHUNT
J15 14
0-60 mV
J15 13 J21
J22
I_AUX
J14 09 ADC IMEAS_REG[M007]
J14 10
J14 11
I_SENS
J16 19
0-5V / 0-20mA
U11-A 0-5V / 0-10V : U11-B
0-20/4-20mA : Live inp.
J16 18
figure 7: Current feedback signal processing diagram.
The operator must choose and configure which source for current and voltage feedback signal wants to work
with according the application, the configuration of current feedback signal processing, filters and selection
or routing is as shown in figure 7.
By default SC6006 takes the current feedback signal from the analog I_SENS input configured as 0-5 V
signal.
11
Voltage feedback signal processing.
The voltage feedback signal can be obtained with direct output voltage connection (J12[p1]-V_REAL) or with
an analog (0-5 V or 0-10 V and also 0-20 mA or 4-20 mA) voltage signal ( J16[p20]-U_SENS). The operator
must ensure and configure which source for voltage feedback signal wants to be used in his application as
shown in figure 8.
R01
U_REAL
J12 01
0-700 VDC
J12 02 J20
ADC UMEAS_REG[M006]
U_SENS
J16 20
0-5V / 0-20mA
U11-C 0-5V / 0-10V : U11-D
J16 18 0-20/4-20mA : Live inp.
figure 8: Voltage feedback signal processing diagram.
By default SC6006 takes the voltage feedback signal from the analog U_SENS input configured as 0-5 V.
3.5 Setpoints and feedback live input signals configuration

All inputs, setpoints and feedback signals, can be configured to work as 0-5 V or 0-10 V and also 0-20 mA.
This configuration is made using the PCB DIP switches (chapter 4.4.2 on page 31).
Also all setpoint and feedback inputs can be configured as 4-20 mA (Live Input). The Live Input mode is
enabled through software. How to set this option it is explained at chapter 4.3.2.4 on page 26.
3.6 Control Modes

The system can work with all its regulating operating modes (PSA and FWS) as open loop scheme setting
the output direct with alpha reference.
In PSA mode it is also possible to make a voltage and current regulation through a PID closed loop scheme.
SC6006 has different control modes:
· OL: Open Loop control mode. Direct regulation of the output according alpha setpoint.
· V: Voltage feedback control. Voltage regulation of the output according voltage setpoint.
· I: Current feedback control. Current regulation of the output according current setpoint.
·IV: Both current and voltage feedback control. Voltage and current regulation of the output
according the most restrictive between current and voltage setpoints.
The control mode is set by software, please refer to chapter 4.3.2.5 on page 26 for further information about
how to set the working control mode of the system.
12
3.7 Soft power ON and soft power OFF
• Soft init slope and soft turn off slope for phase-shift mode (PSA)
When working in PSA mode SC6006 can operate making a soft power ON and soft power OFF. When soft
power ON is set and the unit is started, the phase delay will be gradually decreased until it reaches the
setpoint. The soft power ON time can also be set by software.
Same way, when soft power off is set and the unit is being stop, the phase delay will be gradually increased
from the actual setpoint until it reaches the off state.
In the image is shown a soft power on from 0 to 100%.
alpha
setpoint
100%
0%
time
PSA
waveform
time
figure 9: PSA soft power on waveform example.
The power on and the power off times can be set by software varying from 1 to 30 seconds, how to set the
soft power on and off and the timings is further explained in chapter 4.3.2.6 on page 26.
• Soft init slope and soft turn off slope for proportional mode (FWS). Avoiding transformer
inrush current.
It is recommended to use this configuration in order to reduce the inrush current when controlling a
transformer primary driving resistive loads on its secondary on proportional mode. When a transformer is
first energized a high transient current can flow for several cycles due core saturation. Usually the worst
case inrush happens when the primary winding is connected at an instant around the zero-crossing of the
primary voltage as it occurs every starting period on each mains wave packet when operating in FWS mode.
The inrush current is greater than the nominal operating current of transformer and the ratio can vary from a
few percent up to many times the operating current, this can blow up fuses and trip circuit breaker it also
causes causes harmonics which can excite system resonances and cause dynamic overvoltage, all this
effects may lead to the breakdown of the power equipment.
figure 10: Pulse train example with a soft init on FWS mode.
In many cases a single period (1 st period of the pulse train) fired at 90º will suffice to reduce to its minimum
the inrush peak. In other cases a specific number periods of soft on would reduce at its maximum the initial
inrush current. A recommendation would be to initially set a single cycle of soft turn on, monitorize the initial
peak current and compare it with different number of cycles and select the most suitable for the application.
On figure 10 is depicted as example the initial transient on each packet working with FWS with 5 cycles of
PSA soft init. In this image and for sake of simplicity the wave packets are of 7 periods.
You can find more information regarding the procedure to configure SC6006 to operate with this firing mode
in chapter 4.3.2.6 Soft ON/OFF ramps submenu on page 26 of this manual.
13
3.8 Fault sources and pulse inhibition
When the system is in ON state, the output pulse inhibition it is produced when an enabled fault source in
working condition occurs.
There are 3 different sources that triggers a fault: incorrect mains sync or rotation, external blocking signal
through an external logic inhibit signal or contact block signal and overcurrrent condition.
All this fault conditions can be masked through software or some of them modified. The triggering of fault
signal is made as it is shown in diagram on figure 11.
Sync signal: When unmasked, it is triggered when the phase rotation of mains is reversed than the
configured one or triggered when mains is out of sync, for example by its disconnection or by the
disconnection or out of phasing of one of its phases.
Halt signal: When unmasked, it is triggered when inhibition input (J15[p16]-INHIBIT) or block input (J13[p6]-
BLK) switches on activation state given by signals en_inh and en_ext_blq set by software (chapter 4.3.2.7
on page 27).
OvCurr signal: When unmasked, it is triggered when the measured feedback current exceeds the maximum
set by OV_CURRENT_REG[M036].
EN_SYNC sync_bit
SYNC
EN_INH EN_FAULT
EN_HALT
INH
halt_bit FAULT
EN_EXT_BLQ
BLQ
: SETTABLE CONF. BIT

EN_OV_CURR
: INTERNAL STATE
OV_CURR ov_curr_bit
figure 11: Logic diagram for fault signal.
When any of this 3 fault signals is triggered and fault generation is enabled, a fault condition will occur and
will stop (if it is in working state) the system and set the fault fault flags, those are visible in main menu of on-
board display and with signaling LEDs.
The fault condition will be reset when all fault signals returns to OFF state. Then the system can be triggered
ON again or, if it is set this way, it will resume its previous operation mode.
Output fault dry relay

When fault condition occurs and sets fault signal the output dry relay will be triggered ON following the fault
signal. User can use this output to externally detect and properly set its PLC or uP control system to act
according when a fault is produced.
Fault interlock
SC6006 can interlock a fault condition by using its interlock function. When fault interlock mode is enabled
(see chapter 4.3.2.7 in page 27.) any fault signal will stop the firing mode, and the system will not resume its
previous working and release the fault state mode until all the fault sources are deactivated again and the
system put on OFF state by pressing [OK] push-button on the main menu.
14
3.9 Start up mode
Using the start up setting SC6006 can be configured to, when powered on, start in ON mode, OFF mode or
remembering the last state before it was powered down. By default the unit is configured to start up with the
last system state. This option is software set (chapter 4.3.2.8 on page 27).
3.10 Autoset function
Autoset function SC6006 automatically checks the mains frequency mode, the SCR output assignation and
the phase rotation. By default Autoset function is executed automatically every SC6006 startup, but user can
mask or unmask which properties will set up this function. All its options can be software configured. Also,
Autoset function can be triggered by software in any moment with no need to turn on and off the system. See
chapter 4.3.2.9 on page 28.
Note:
When powered on, SC6006 automatically starts the autoset function before initialize all the system. So, in order to work
properly all the power system must be connected and powered on at the same time or before power on the SC6006.
Otherwise the Autoset function would be unable to determine the frequency of mains or rotation or output assignation
and will be configured in a default mode or with the previous detected configuration.
Mains frequency configuration:

By default every time the board is powered up checks the mains frequency mode (50 Hz or 60 Hz) and then
it can automatically configure itself to work at the corresponding mains frequency. The operator can also
mask this option and manually set through software the frequency of operation.
Mains frequency autodetect option can be masked and configured by software:
SUBMENU 1.8: AUTOSET > AC freq > [Auto/50Hz/60Hz]
If the mains frequency autoset is enabled but during the autoset process the system cannot determine it, the
working frequency will be set the same as the last time used.
Phase rotation autoset:

SC6006 can autodetect and correct a change in phase rotation. This occurs when, in the mains, 2 phases
were swapped (e.g.: S and T swaps yelding R-S-T → R-T-S).
Phase rotation autodetect option can be masked and configured by software:
SUBMENU 1.8: AUTOSET > Rotation > [Auto/CW/ACW]
By default phase rotation autoset is executed automatically every SC6006 startup and checks if there is any
change since the last configuration. If there is any change the system autoconfigures itself. This
autoconfiguration can also be masked.
If the phase rotation autoset is enabled but during the autoset process the system cannot determine it, the
phase rotation will be set the same as the last time used.
SCRs automatic output assignation:

SC6006 can autodetect how the SCRs has been connected to the PCB and autoconfigure correctly the
corresponding output signals.
The SCRs automatic assignation detects and corrects the output signal assignation scheme in the following
cases:
– A swap between the SCRs in a same branch (W3C or B6C) or module. e.g. : SCR1 ↔ SCR2.
– A swap between 2 pairs of SCRs of different branches or between 2 modules. E. g. : SCR1 ↔
SCR3 and SCR2 ↔ SCR4.
15
If the operator wants to use this option SC6006 must be connected to a resistive load in B6C scheme, and in
a delta or wye resistive load in W3C. It is also recommended to connect the neutral.
In some cases outputs autoset may be unable to find the correct outputs assignation and, by default will
disable all the outputs (0). The user can override the automatic configuration by manually setting up the
output assignation.
SCRs output assignation option can be disabled and configured by software:
SUBMENU 1.8: AUTOSET > Outputs > [No/Auto]
By default outputs autoset is disabled. Can be useful to use this function when installing the power stack the
first time to get a quick and easy configuration and, then, save the configuration and disabling the outputs
autoset mode.
If the automatic outputs detection in autoset is enabled but during the autoset process the system cannot
determine it, the outputs assignation will be the same as the last time was saved in EEPROM.
Note:
The SCRs automatic assignation option works only for W3C and B6C schemes with resistive loads. For other topologies
the user must leave disabled the outputs autoset option and configure the system according the SCRs connection
scheme through SUBMENU 1.9: OUTPUTS.
3.11 Output assignation option

Each output of the SC6006 can be software set independently to operate according R, S, or T phase and for
the positive semi-cycle (r,s,t) or the negative semi-cycle (r',s',t'). Also can be permanently disabled (0).
The output assignation option is found at:
SUBMENU 1.9: OUTPUTS
Please refer to chapter 7 on page 41 for the standard topologies and its corresponding outputs configuration.
3.12 Saving all the changes and configurations

When the operator has made some settings change or properly configured all the options of the system the
new configuration must be saved in the internal EEPROM through:
SUBMENU 1.11: SAVE > [OK]
All changes not properly saved in the EEPROM will be lost during a power down and the previous EEPROM
saved configuration will be restored in the next power up of the system.
Note:
Remember to save the configurations to the internal EEPROM every time a change is made or all the changes will be
lost when system is powered off.
3.13 Restore default configurations

The factory default software configurations of the system can be restored at any moment using the menu
option:
SUBMENU 1.12: RESTORE > [OK]
When restored, the system will be automatically rebooted and all software configurations back to default
factory set.
16
4 SETTINGS AND OPERATION
In this chapter is given a complete device overview, with a description of all available input/output signals
and connections available and a brief description of all software options and on-board hardware
configurations made by jumpers and DIP-switches.
4.1 PCB connectors overview

J11 - SYNCHRONISM OUTPUT SCR FIRING
CONNECTOR CONNECTORS
SEMICODE
ELECTRONICA
®
PWR
SC6006
LCD CONTRAST
FIRING
SIGNALING LEDS
FAULT
OV CURR
EXT BLK
MENU OK
RESET
COARSE FINE
J32 - DB-9 (DCE) RS-232

COM CONNECTOR
U_SENS I_SENS I_ SET U _SET I_ SENS U _SEN S ALPH A
SC6006
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
J1 - POWER J12 - FEEDBACK J13 - EXTERNAL BLOCK J14 - CURRENT J15 - SETPOINTS J16 - FEEDBACK AND
SUPPLY VOLTAGE AND DRY OUTPUT FAULT INPUT FEEDBACK AND INHIBIT ALPHA SETPOINT
figure 12: Connectors PCB overview.
Terminal Name Description Terminal Name Description

AC_IN1 AC / DC power supply input. 8 GND Signal ground.
J1
AC_IN2 AC / DC power supply input. 9 AUX_I_R R phase input for CT.
R R_SYNCH Mains R phase input. J14 10 AUX_I_S S phase input for CT.
S S_SYNCH Mains S phase input. 11 AUX_I_T T phase input for CT
J11
T T_SYNCH Mains T phase input. 12 I_SHUNT Shunt input terminal.
N NEUTRAL Mains neutral input. 13 GND Signal ground.
1 V_REAL Direct voltage input feedback. 14 I_SETPOINT Input current setpoint.
J12
2 GND Signal ground. J15 15 U_SETPOINT Input voltage setpoint.
3 K1_NC Output dry relay N/C contact. 16 INHIBIT inhibit input signal.
4 K1_COM Output dry relay COM contact. 17 VCC +5 VDC output reference.
J13 5 K1_NO Output dry relay N/O contact. 18 GND Signal ground.
6 BLK Blocking signal input. 19 I_SENS Input current feedback.
7 VDD +15 VDC from SC6006. J16 20 U_SENS Input voltage feedback.
21 ALPHA_INP Input alpha setpoint.
22 VDD +15 VDC from SC6006.
table 1: List of connectors and pinning.
17
4.2 Connectors
Following is listed and described every connector and every output/input signal available of the SC6006.
4.2.1 Power supply connector (J1)

Connector J1 is the input mains supply connection for the switched mode power supply on board.
The system can be powered with AC (or DC) power source from 195 VAC to 480 VAC. For more technical
details or maximum and recommended values and parameters please refer to chapter: 10-TECHNICAL
SPECIFICATIONS.
J1
figure 13: Detail of mains supply input connector.
The connector type is a MSTBVA series (or equivalent) from Phoenix Contact (ref. MSTBVA2,5/3-G-5,08).
The board is also provided with the matching plug connector (ref. MSTB2,5/3-ST-5,08).
4.2.2 Synchronism connector (J11)

Synchronism connector is labelled (PCB silkscreen) indicating the three phases R, S, T and neutral N. Mains
connection must guarantee concordance with the SCRs to get sure that the synchronism and phase rotation
is correct.
If the concordance is wrong this can be fixed without reconnecting the SCRs by means Autoset function or
manually assigning the correct outputs by software.
In case the phase rotation is wrong the PCB can autodetect and solve it using the Autoset function or, if it is
enabled phase rotation autoset during the power on, just by reset the system.
J11
figure 14: Detail of sync input connector.
The connector type is an MSTBA series (or equivalent) from Phoenix Contact (ref. MSTBA 2,5/7-G-5,08).
The board is also provided with the matching plug connector (ref. MSTB 2,5/7-ST-5,08).
18
4.2.3 Feedback voltage signal connector (J12)
Direct voltage feedback input is made on J12 connector. Please note that in those cases where control
board is controlled by external equipments, like PLC, microcontrollers, etc, without isolated outputs, it must
be considered to have all the feedback elements isolated. Using elements like shunts to close the current
loop, and voltage feedback could not be done directly if galvanic isolation is required.
There are available isolated feedback modules designed to work with this control board. Please see chapter
8 -AVAILABLE ACCESSORIES on page 50 for a list and explanation of suitable accessories for SC6006.
- J12 PINOUT:
• Terminal 1 (V_REAL): Direct voltage input feedback signal.
• Terminal 2 (GND): PCB signal ground.
J12
The connector type is an MSTBVA series (or equivalent) from Phoenix Contact (ref. MSTBVA2,5/3-G-5,08).
The board is also provided with the matching plug connector (ref. MSTB2,5/3-ST-5,08).
4.2.4 External block and dry output fault connector (J13)

The external block connector and dry output fault connector provides the user an input blocking signal (using
for example an external contactor or switch) and an output dry relay for fault signaling.
- J13 PINOUT:
• Terminal 3 (K_NC): Output dry relay N/C contact.
• Terminal 4 (K_COM): Output dry relay COM contact.
• Terminal 5 (K_NO): Output dry relay N/O contact.
• Terminal 6 (BLQ): Input terminal of the blocking signal.
• Terminal 7 (VDD): Positive terminal blocking signal (15 VDC).(*) J13
(*) please do not use this terminal to power other external devices. Refer to ELECTRICAL CHARACTERISTICS TABLE for further
information.
Terminal 6 (BLQ) must be shortcircuited with Terminal 7 (VDD) for trigger ON the input blocking signal.
Terminals 3-5 are those corresponding to the dry output fault relay. Relay switches ON (Terminal 4
connected with Terminal 5) when fault occurs. Otherwise, if there is no fault, relay switchs OFF (Terminal 4
connected with Terminal 3). Please see the connection diagram for J13 in figure 15.
output fault
signaling relay
K1
2 3 4 5 6 7 8 9
external block
switch
figure 15: Connection example diagram for J13.
19
The J13 connector type is an MCV series (or equivalent) from Phoenix Contact (ref. 1803442). SC6006 is
also provided with the matching plug connector (ref. 1803604).
Note:
By default SC6006 is configured to operate with a normally-off blocking contactor. To work without the blocking mode or
with a normally-on contact you must set this option through software. Please see chapter 4.3.2.7 in page 27.
4.2.5 Current input feedback connector (J14)

When necessary AC/DC current measurement can be achieved by using current transformers (CT) or shunt
respectively. J14 interfaces those feedback current signals.
- J14 PINOUT:
• Terminal 8 (GND): Ground connection
• Terminal 9 (AUX_I_R): R phase input for auxiliary CT feedback.
• Terminal 10 (AUX_I_S): S phase input for auxiliary CT feedback.
• Terminal 11 (AUX_I_T): T phase input for auxiliary CT feedback.
• Terminal 12 (I_SHUNT): Shunt input terminal.
J14
U_SENS
6 7 8 9 10 11 12
I_R
I_S
I_T
current
sensors
figure 16: Connection diagram example for J14.
The J14 connector type is an MCV series (or equivalent) from Phoenix Contact (ref. 1803442). The board is
Note:
Auxiliary feedback uses the signal from a current transformer (200 mA output), in order to be able to regulate AC
currents. Below are indicated our recommended current transformers:
Current Transformers
TTS017 25-50-100A/0.2A Input current: 25, 50 or 100 A
TTS040 200-300-400/0.2A Input current: 200, 300 or 400 A
TTS040 600/0.2A Input current: 600 A
20
4.2.6 Setpoints and inhibit connector (J15)
Voltage and current setpoints and inhibit signal are interfaced with this connector. It also provides a 5 V
reference in case setpoint potentiometers are used.
- J15 PINOUT:
• Terminal 13 (GND): Negative terminal from the regulator
potentiometers or GND reference.
• Terminal 14 (I_SETPOINT): Adjustment terminal from the current
regulator potentiometer or current setpoint input.
• Terminal 15 (U_SETPOINT): Adjustment terminal from the voltage
regulator potentiometer or voltage setpoint input. J15
• Terminal 16 (INHIBIT): Inhibit input signal.

• Terminal 17 (VCC): Positive terminal from the regulator potentiometers or 5 V reference(*).
information.
U_SENS I_SENS I_SET U_SET
11 12 13 14 15 16 17
Current reg. Voltage reg.

Potentiometer Potentiometer
Notes:
- Inputs can be driven by potentiometers. This potentiometers can be any type, but with a recommended value of 4.7 kΩ.
- When the adjustment cursor of the potentiometer is situated to the positive side, the supplying voltage is at the
maximum level.
- It is also possible to control the inputs with 0-5 V, 0-10 V, 0-20 mA or 4-20 mA signals applied to the adjustment
terminals (referred to ground).
21
4.2.7 Feedback and alpha setpoint input connector (J16)
Voltage and current feedback signals and alpha setpoint signal are interfaced with this connector.
- J16 PINOUT:
• Terminal 18 (GND): Negative terminal from the regulator
potentiometers or GND reference.
• Terminal 19 (I_SENS): Current feedback signal input.
• Terminal 20 (U_SENS): Voltage feedback signal input.
• Terminal 21 (ALPHA_INP): Alpha reference input.
• Terminal 22 (VDD): Positive terminal from 15 V reference(*). J16
information.
I_SENS U_SENS ALPHA
Current
18 19 20 21 22
sensor
SCRs POWER STACK
+5 VDC
Alpha reg.
Potentiometer
COM GND
Voltage
sensor
Notes:
- ALPHA_INP setpoint can be driven by a potentiometer. This potentiometer can be any type, but with a recommended
value of 4.7 kΩ. If a potentiometer is used its positive +5 V DC reference can be wired to J15:17 (VCC) and GND
reference to J16:18 (GND).
I_SENS, U_SENS and ALPHA_INP can work with 0-5 V, 0-10 V, 0-20 mA or 4-20 mA signals level.
22
4.2.8 Output SCR firing connectors (SCR1-SCR6)
The output SCR firing connectors are labelled (PCB silkscreen) indicating the six outputs SCR1 to SCR6
and its correspondent G and K connections, please see figure 19. Mains connection must guarantee
concordance with the SCRs to get sure that the synchronism and phase rotation is correct.
If the concordance is wrong this can be fixed without reconnecting the SCRs by means Autoset function or
manually assigning the correct outputs by software.
In case the phase rotation is wrong the PCB can autodetect and solve it using the Autoset function or, if it is
enabled phase rotation autoset during the power on, just by reset the system.
TO SCRs (SCR1-SCR6)
figure 19: Detail of output SCR firing connectors.
Connector Gate Cathode

SCR1 G1 K1
SCR2 G2 K2
SCR3 G3 K3 SCR6
SCR5
SCR4
SCR4 G4 K4 SCR3
SCR2
SCR5 G5 K5 SCR1
SCR6 G6 K6
The connectors type is an MSTBVA series (or equivalent) from Phoenix Contact (ref. 1755736). The board is
also provided with the matching plug connectors (ref. 1757019).
Notes:
- For thyristor connection, see chapter 7 where there are the most typical circuits. And please read the mounting
recommendations on page 48,
- Avoid long cables in the firing system, and always use twisted or shielded cables (preferred).
4.2.9 Serial communications DB-9 connector (J32)

The connector type is a specific DB-9 male (DTE) connector.
Can be interfaced to a standard PC serial port or PLC RS232
port.
Please check chapter 5 -SERIAL COMMUNICATION on page

for a more detailed information regarding te use of the SC6006
serial communication port.
J32
23
4.3 LCD menu settings and navigation
SC6006 has an on-board integrated alphanumeric LCD that provides an user interface to easy set up and
monitor every configuration or setting of the system.
When initializes SC6006 starts on main menu as is shown in figure 20 and there are a total of 3 menus. The
main menu (on top of the figure), settings menu, and registers menu. User can go cyclically through this
menus clicking the [MENU] push-button.
[MENU]
[MENU]
REGISTERS MENU SETTINGS MENU
[MENU]
figure 20: menu sequence of SC6006.
The [OK] push button triggers ON the SCR controller when its pushed at main menu and accepts the
introduced changes or access to the submenus when it's pressed in the other menus.
The [UP] an [DOWN] push buttons move up and down in the menus and, when selected, increases or
decreases the settings variables.
4.3.1 Main Menu:

In the main menu you can see in a glimpse the actual state of the system.
– Faults: If there is any fault condition it will appear “FLT!” at the left LCD corner.
– ON/OFF system status. At the right LCD corner.
– Halt (H), sync (S) and overcurrent (I) fault flags.
– Voltage and current setpoint references or alpha reference.
– Voltage and current measurements.
– Firmware version.
fault mode sign halt and synch flags firmware version
PWR
FIRING
FAULT
OV CURR
EXT BLK
MENU OK
RESET
voltage setpoint current setpoint ON/OFF system status
figure 21: Detail of main menu in LCD display.
By default SC6006 will show in the first line of main menu its version and if there is any fault. In the second
line the values (in %) of the reference inputs (current and voltage).
By pressing the push-button [UP] the first line of main menu will switch to the default information to show the
24
actual values (in %) of the sensed current and voltage. If the SC6006 is in fault mode then the first line
always will show the default information.
By pressing the push-button [DOWN] the second line of the main menu will switch to the default information
to show the actual value (in %) of the alpha reference.
When during the initialization SC6006 could not determine the phase-rotation, frequency or output
assignation and its default configuration it is ben made a “!” character will be shown on the fist position of the
second line.
4.3.1.1 LCD contrast adjusting potentiometer

By means the potentiometer P5 (see figure 22) operator or user can readjust the contrast of LCD in case
more or less contrast is needed according the environmental light or visual conditions.
The contrast is in factory adjusted for an optimal LCD reading.
PWR
SC6006
LCD CONTRAST
FIRING
FAULT
OV CURR
EXT BLK
MENU OK
RESET
COARSE FINE
U_SENS I_SENS I_ SET U _SE T I_S ENS U_SE NS ALPHA
SC6006
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
figure 22: P5 LCD contrast adjusting potentiometer
4.3.1.2 LCD backlight

When SC6006 is in the main menu you can switch the LCD backlight OFF by pressing and hold for a second
the push-button [DW].
The LCD backlight can be turned ON again by pressing and hold for a second the push-button [UP].
By default LCD backlight is ON.
Note:
All the changes of visualization, information and backlight state introduced in the main menu can be saved in EEPROM
by submenu 1.11 (submenu save).
4.3.2 Settings menu

In settings menu it is possible to change all the internal characteristics and modes
of operation of the system. We can access this menu pressing [MENU] push-
button when we are in main menu. SETTINGS MENU
4.3.2.1 Topology option

MENU 1: SETTINGS > Topology > [B6C / W3C]
TOPOLOGY OPTION
By pressing [OK] button we can change between B6C topology and W3C topology operation.
By default SC6006 is configured in W3C topology.
25
4.3.2.2 Mode option
MENU 1: SETTINGS > Mode > [PSA / FWS / RLY / DRV]
MODE OPTION
By pressing [OK] button we can change between PSA, FWS, RLY and DRV modes of operation.
By default SC6006 is configured in PSA mode.
4.3.2.3 Reference submenu

SUBMENU 1.2: REFERENCE > alpha > [An / Dig]
> voltage > [An / Dig]
> current > [An / Dig] REFERENCE SUBMENU
By pressing [OK] button we access to the Reference submenu. In this submenu we can change the
references which SC6006 uses to calculate the setpoint. It is possible to choose between analog references
for alpha, voltage and current or use the digital registers for this setpoints .
By default SC6006 is configured with all of its inputs as analog references.
4.3.2.4 Live-zero input submenu

SUBMENU 1.3: INPUTS > i_ref > [0 mA/ 4 mA]
> i_meas > [0 mA/ 4 mA]
LIVE INPUT SUBMENU
> u_ref > [0 mA/ 4 mA]
> u_meas > [0 mA/ 4 mA]
> alpha_inp > [0 mA/ 4 mA]
By pressing [OK] button we access to the Live-inputs submenu. In this submenu we can set each input
working as a normal input or as live input (4-20 mA). Please note that the DIP-Switches configuration must
be set according the voltage or current levels required.
By default all inputs in SC6006 are configured in zero mode (no live-input).
4.3.2.5 Control option

MENU 1: SETTINGS > Control > [OL / I / V / IV]
CONTROL OPTION
By pressing [OK] button system changes between “OL” (open loop), “I” (current regulation), “V” (voltage
regulation) or “IV” (both current and voltage regulation).
By default SC6006 is configured in OL mode.
4.3.2.6 Soft ON/OFF ramps submenu

SUBMENU 1.6: ON/OFF Ramps > Soft ON > [OFF / ON]
> Time ON > [1..30]s/c(+ -)
ON/OFF RAMPS SUBMENU
> Soft OFF > [OFF / ON]
> Time OFF > [1..30]s/c(+ -)
26
• When SC6006 is operating on PSA Mode:
By pressing [OK] button it access to the Soft ON/OFF ramps submenu. In this submenu you can activate or
deactivate the soft turn on and soft turn off and set up the both times.
By default SC6006 is configured with 10 seconds (both UP and DOWN) ramps but with soft on and off
options disabled.
• When SC6006 is operating on FWS Mode:
By pressing [OK] button it access to the Soft ON/OFF ramps submenu. In this submenu you can activate or
deactivate the soft turn on and soft turn off on FWS mode and set up the both number of cycles in which
PSA will be used.
By default SC6006 is configured with 10 cycles (both UP and DOWN) ramps but with soft on and off options
disabled.
Note:
On cases where a determinated number of cycles of turn on is set, the minimum firing packet will be this number of
cycles A. On those cases where a determinated number of cycles B of turn off where set the minimum firing packet will
be B. On those cases where turn on and turn off is set with A and B cycles respectively the minimum firing packet will be
A+B cycles. Additionally, if alpha setpoint is set to 0% SC6006 will not fire, alternatively if alpha setpoint is set to 100%
the board will be permanently activated ignoring turn on and turn off clycles.
4.3.2.7 Faults submenu

SUBMENU 1.7: Faults > Blq > [N.OFF / N.ON]
> Inh > [N.OFF / N.ON]
> Halt > [En / Dis] FAULTS SUBMENU
> Sync > [En / Dis]

> OvCurr > [En / Dis]
> Fault > [En / Dis]
> Interlock > [En / Dis]
In this submenu we can enable or disable each one of the sources of fault (Halt, Sync and OvCurr) and even
the fault signal itself (Fault). We also can set if the signals block and inhibit works as a normally-on or
normally-off signals. Besides, the last option in submenu (Lock fault) interlocks the fault signal in case of fault
event and stops the system and blocks it until all faults are gone and the SC6006 is in OFF mode by
pressing [OK] push button in main menu.
By default SC6006 is configured with all the faults enabled and block and inhibit signals normally off.
Interlock fault disabled.
4.3.2.8 Start up option

MENU 1: SETTINGS > StartUp > [OFF / ON / Last]
START UP OPTION
By pressing [OK] button we can change between ON, OFF or Last state.
Mode “ON” enables the firing every time the system is powered up. Mode “OFF” starts always SC6006
stopped. In “Last state” mode starts the system maintaining the last state when it was powered down.
27
By default SC6006 is configured with LAST state when start up the system.
4.3.2.9 Autoset options submenu

SUBMENU 1.9: Autoset > AC Freq > [50Hz / 60Hz / Auto]
> Outputs > [No / Auto]
> Rotation > [No / Auto] AUTOSET SUBMENU
> Autoset?
By pressing [OK] button we access to the Autoset submenu. In this submenu we can configure the mains
frequency (50 or 60 Hz) or leave the SC6006 finds by itself the working frequency. Also SC6006 can set up
by itself the outputs configuration and the phase rotation.
With the last option the SC6006 will start the autoset procedure.
The autoset is launched every time the system is powered on autosetting the enabled configurations.
By default SC6006 is configured as 50 Hz mains frequency with the outputs detect disabled and automatic
rotation enabled.
4.3.2.10 Outputs assignation submenu

SUBMENU 1.10: Outputs > SCR1 > [0 / r / r' / s / s' / t / t' / 1] (+ -)
> SCR2 > [0 / r / r' / s / s' / t / t' / 1] (+ -)
> SCR3 > [0 / r / r' / s / s' / t / t' / 1] (+ -)
> SCR4 > [0 / r / r' / s / s' / t / t' / 1] (+ -)
> SCR5 > [0 / r / r' / s / s' / t / t' / 1] (+ -)
> SCR6 > [0 / r / r' / s / s' / t / t' / 1] (+ -)
By pressing [UP] and [DOWN] we can select the SCRs outputs phase assignation. Pressing [OK] and then
UP] and [DOWN] we can move through each phase and assign the output SCR.
By default SC6006 outputs are configured as: r – r ' – s – s' – t – t'.

r: meaning this output will switch during the positive semi-cycle of R-phase.
r': meaning its output will switch during the negative semi-cycle of R-phase, and similarly for the
other phases.
4.3.2.11 Communications submenu

SUBMENU 1.9: COM > RS232 > [En / Dis]
> Remote > [En / Dis]
COMMUNICATIONS SUBMENU
By pressing [OK] in “RS232” option we can activate or deactivate the serial communication of the unit.
By pressing [OK] in “Remote” option we can activate or deactivate the serial communication of the unit when
operating with a SCRP6006 remote panel please read on chapter 8.1 - SCRP6006 for further information.
By default SC6006 is configured with its serial port activated and the communication with a SCRP6006
deactivated.
4.3.2.12 Save changes option

SUBMENU 1.10: Save all?
SAVE CHANGES
By pressing [OK] in “Save all?” a warning message will be displayed and then, if we push another time [OK]
28
all changes introduced will be saved in the internal EEPROM. By pressing [MENU] we will return to previous
menu.
4.3.2.13 Restore option

SUBMENU 1.10: Restore?
RESTORE CHANGES
By pressing [OK] in “Restore?” a warning message will be displayed and then, if we push another time [OK]
all configurations will be restored to the factory settings and then the controller rebooted.
4.3.3 Registers menu

In this menu it is possible to read and change some of the internal registers as
digital setpoints or frequency and duty cycle of the train pulse of the SCRs.
The registers can be highlighted with [UP] and [DOWN] push-buttons, selected by
pressing [OK] and then using [UP] and [DOWN] we can adjust, manually, its REGISTERS MENU
values.
Next will be briefly explained each of this set registers.
Digital setpoints registers

> alpha_d: This is the corresponding digital register to adjust the alpha setpoint when the unit is
configurated to operate with the digital alpha setpoint register.
This is a 10 bit register and can be set from 0 (0%) to 1023 (100%).
> uref_d: This is the corresponding digital register to adjust the voltage setpoint when the unit is
configurated to operate with the digital voltage setpoint register.
> iref_d: This is the corresponding digital register to adjust the current setpoint when the unit is
configurated to operate with the digital current setpoint register.
By default all digital setpoints registers are set to 0.
Overcurrent threshold register

> o_curr: This register adjust the maximum rate of overcurrent when the overcurrent fault signal
is triggered.
The o_curr register can be manually set from 50% to 300% of the measured input current with steps of 50%.
By default overcurrent register is set to 200%.
Output pulse gate train registers

> fsw: This register adjust the switching frequency for the output pulse gate train. Can be set from
1 to 25 kHz and by default it is set for a frequency of 12 kHz.
> duty: This register adjust the duty cycle for the output pulse gate train. Can be set from 5% to
30% and by default it is set for a duty of 25%.
Topology sync delay registers

> dly1: This register adjust the firing delay when W3C topology is used. It is, by default,
configured to adjust the firing signal to the mains signal and normally there is no need to change its value.
> dly2: This register adjust the firing delay when B6C topology is used. It is, by default, configured
to adjust the firing signal to the mains signal and normally there is no need to change its value.
29
4.3.4 Debug menu
If, when power on the SC6006, we maintain pressed the [UP] push-button we will enter in debug mode. In
this mode we can access to another menu called debug menu. In this menu we can see with the on board
LCD the values of many internal registers of the system. This mode is intended only for debug purposes.
Note: All configuration changes introduced by user must be saved before power down or resetting the equipment or all
changes will be lost.
4.4 Jumpers and DIP Switches configurations

There are some configurations that can not set in software and must be set using the jumpers and DIP
switches of the board. Following you will find an explanation of all the configurations set by jumpers and DIP
switches.
4.4.1 Jumpers J7 and J20 to J24

Jumpers allow to configure the different input options of the control board. In table below, there are indicated
the possible jumper configuration options.
Jumper Description
J7 Used to control the gain of the direct voltage feedback input. Further description in 4.4.3.
Used to change the source of voltage feedback signal between direct voltage feedback input
JP20
and analog input voltage signal input.
JP21 Used to select between auxiliary current transformers or shunt.
Used to change the source of current feedback signal between auxiliary current transformers or
JP22
shunt and analog input current signal input.
It will be used for feedback with shunt in positive terminal and inverted voltage feedback. See
JP23
chapter 7.3.2 on page 44.
JP24 Do not use this jumper, leave all its pins unconnected.
Notes:
In case of using an isolated sensor for the DC current feedback with J16[p19]-I_SENS, please double check
the measuring direction of the sensor. Current feedback signal must be always positive.
In the following table can find the correct jumper configuration for common application schemes.
APPLICATION JP20 JP21 JP22 JP23

Rectifier (shunt + controlled) UP UP UP UP
Rectifier (shunt - controlled) UP UP UP DW
AC control (aux. feedback) UP DW UP DW
External voltage and current control DW DW DW DW
Feedback by SCCAVO2 OA UP DW DW DW
Warning notes:
- Make sure and double check the position of the plugging connectors (jumpers), following previous indications.
- JP70 and JP71 are reserved, do not use them, they always must be connected.
- Do not let any jumper unconnected except for the J24 jumper.
30
4.4.2 DIP Switches
DIP switches sets the type of signal input for current and voltage references (I_SET, U_SET, voltage and
current references (I_SENS, U_SENS) and alpha reference (ALPHA).
All this signals can be configured with DIP switches to work as 0-5 V, 0-10 V and 0-20 mA. For live input (4-
20 mA) the configuration is made through software.
J11 J12 J13
ON DIP ON DIP ON DIP
1 2 3 4 1 2 3 4 1 2 3 4
I_SET U_SET I_SENS U_SENS ALPHA
figure 23: Detail of the default configuration of DIP

switches.
There are 2 switches assigned to each input as we can see in figure 23. In this figure is shown the default
configuration of the switches. With this configuration all inputs are set to work as 0-5 V signals.
0-5 V mode (ON-OFF):
ON If we want to adjust I_SET (e.g.) input for 0-5 V mode the 2 correspondig switches must be set as
follows: first switch ON (up position) and second switch OFF (down position). Same way for the
1 2 other input signals.
0-10 V mode (OFF-OFF):

ON If we want to adjust I_SET (e.g.) input for 0-10V mode the 2 corresponding switches must be set as
OFF (down position). Same way for the other input signals.
1 2
0-20 mA / 4-20 mA mode (ON-ON):

ON If we want to adjust I_SET (e.g.) input for 0-20 mA / 4-20 mA mode the 2 corresponding switches
must be ON (up position). Same way for the other input signals.
1 2
Warning note:
Please double check if the configuration set by the DIP switches corresponds to the input signals you use. And avoid by
all means the OFF-ON configuration.
31
4.4.3 Setting the gain for direct voltage feedback input
Voltage input feedback gain for J12[p1]-V_REAL input can be precisely adjusted for work correctly sensing a
wide range of load voltages (see technical specification and maximum rated values). The gain of direct
voltage feedback is adjusted by regulating R01 resistance using a pair of potentiometers (R01C and R01F)
and a jumper on board (J7).
- How to adjust R01

The voltage input feedback gain is adjusted by setting the R01 resistor. This resistance can be adjusted
setting the potentiometers R01C (coarse) and R01F (fine). With a multimeter the user can measure the R01
resistance value measuring between the points A and B of the figure 24 with all the system powered OFF.
Jumper J7 adds 2.2 kΩ when down and 220 kΩ when up in order to adjust more widely the total resistance
value.
MENU
A
COARSE FINE
R01
PWR
B
SC6006
LCD CONTR AST
MENU
COARSE FINE
U_SENS I_SENS I _S E T U_S E T I_S E NS U_S E NS ALP HA
SC6006
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
figure 24: Detail of test points for R01.
R01 resistance for the maximum voltage regulation, it must be calculated and regulated with R01C
and R01F potentiometers following the indications below:
For direct feedback (without galvanic isolation): R01=2230/Vr

R01=[kΩ], Vr=[V] (rectifier bridge maximum output voltage or DC maximum input voltage)
For feedback through SCCAV02-OA (galvanically isolated): R01=220 kΩ
Note: When gain is properly regulated according the input voltage, the signal present in the upper pin of J20 must go
from 0 to 5 V when input voltage go from 0 to 100%.
In case R01 has been set but the output regulation do not reach the 100% try to decrease gradually the gain voltage
feedback to the point where the unit regulation go from 0 to 100%.
By default SC6006 is factory calibrated for measurement of 400 VAC through bridge rectifier input (565 VDC
input).
4.5 LED Indications

There are a total of 5 LEDs in the PCB that shows the
state of the system. If it is firing, in fault mode or there
PWR is an overcurrent or blocking event:
PWR LED: (Green) it indicates when the system is

powered.
FIRING LED: (Orange) it indicates the system is in ON
state and firing.
FAULT LED: (Red) it indicates there are a fault signal
FIRING
FAULT
active and the outputs disabled.
OV CURR
EXT BLK
OV CURR LED: (Red) indicates the situation of over
RESET
current.
EXT BLK LED: (Red) indicates, when enabled, if there
is an external blocking signal.
32
5 SERIAL COMMUNICATION
SC6006 has a serial communication port (J32) to make basic operations of control and configuration of the
system through a RS232 interface with, for example, a remote PC or a PLC.
The default configuration of the serial link is as follows:
Baud rate: 9600bps
Parity bit: none
Stop: 1 bit
Flow control: none
To interface it with a standard RS-232 serial communication port, you will need a specific DB-9 null modem
cable. You can, additionally, order the cable with the SC6006 board.
PIN #1 PIN #5
PIN #6 PIN #9
figure 25: J32 Connector (male D-SUB9) pinning detail. SC6006 lateral view.
Pin No. Name Dir Notes / Description

1 VAUX OUT Do not use.
2 TD OUT Transmit serial data from SC6006.
3 RD IN Received serial data from remote DTE.
4 DTR OUT Data Terminal Ready. Loopback with DSR, internally connected.
5 SGND - Signal ground (SC6006).
6 DSR IN Data Set Ready. Loopback with DTR, internally connected.
7 RTS OUT Not connected.
8 CTS IN Not connected.
9 RI IN Not connected.
When powered on SC6006 sends a welcome message and awaits for the user instructions. If we interface
SC6006 with a PC with HyperTerminal (e.g.) when system is power up we will see the following:
SC6006 - Command line
>
Then the communication it has been correctly established.
33
5.1 Overview available command set
SC6006 has 4 different types of instructions:
– Query instructions (?).
– Signal instructions (*).
– Memory read instructions (R).
– Memory write instructions (S).
To send any instruction to SC6006 and for being processed this instruction must end with a 0x10[“NL”]
character (or an enter pulsation if HyperTerminal is used).
All the sent instructions will return back to the user (at least) the 0x10[“NL”] character plus the character of
waiting for a new instruction: 0x3E[“>”]. This 2 characters will always be sent back even when the echo
mode is deactivated.
5.2 Query instruction set

The query instructions which starts with 0x3F[“?”] character, gives the user a fast read of usual registers as
voltage feedback register, current feedback register, alpha register, etc. And also get information about the
software version installed in the system and its serial number.
5.2.1 “?ver” query version command

Returns the version of the firmware and hardware of the unit.
>?ver
PCB:v1.0 firmware:v1.28
5.2.2 “?S” query status register

Returns the value of the status register. This register is described in chapter 6.1.1 on page 37. This
instruction is equivalent to read the register M000.
5.2.3 “?A” query alpha register

Returns the value of the alpha register. This instruction is equivalent to read the register M005.
5.2.4 “?U” query voltage register

Returns the value of the current register. This instruction is equivalent to read the register M008.
5.2.5 “?I” query current register

Returns the value of the status register. This instruction is equivalent to read the register M009.
5.3 Signal instruction set

The signal instructions starts with the 0x2A[“*”] character; this instructions makes a change in the system or
sends a signal. Allowing to send a remote push-button signal, remote reset signal, etc. This instructions
returns no value response but the 0x10[“NL”] and 0x03[“>”] when the instruction has been processed.
34
5.3.1 “*OK” signal command
Sends a remote pulsation of the [OK] push-button.
5.3.2 “*MENU” signal command

Sends a remote pulsation of the [MENU] push-button.
5.3.3 “*UP” signal command

Sends a remote pulsation of the [UP] push-button.
5.3.4 “*DW” signal command

Sends a remote pulsation of the [DW] push-button.
5.3.5 “*RMT” signal command

Enables or disables the remote mode for the SC6006 in order to use it with a remote control LCD as
SCRP6006, this command activates a new set of reserved instructions less verbose and more M2M
oriented. The description of this additional instruction set is out of the scope of this manual.
5.3.6 “*ECHO” signal command

Enables or disables the echo in serial communication.
When the echoing option is enabled, SC6006 transmits (echoes) data characters it receives back to the
sender. When the echoing option is disabled, SC6006 will not echo the characters back to the sender; this,
of course, does not prevent SC6006 from responding to data characters received.
This option is intended for a more man-machine friendly interface, for M2M communications disabling echo
mode reduces the redundant information sent.
Echo mode is, by default, activated.
5.3.7 “*HOME” signal command

Returns the on-board LCD displayed menu to the main menu.
5.3.8 “*RST” signal command

Sends a reset signal to the unit. SC6006 will restart itself.
5.3.9 “*SV” signal command

Sends a save signal to the unit. SC6006 will save all the configuration changes introduced.
35
5.4 Memory read instruction
The memory read instructions starts with 0x4D[“M”] character followed by 3 numeric characters which
specifies the memory address to read through communications port.
This instruction returns the decimal value of the specified register.
>M001
SC6006: 65460d
Note:
The table 2 in page 37 shows the a list of available registers to read with its corresponding brief description.
5.5 Memory write instruction

The memory write instruction starts with “S” character followed by 5 numeric characters which specifies the
value (in decimal) which will be overwritten in the previously read memory. All the writable registers are 16
bits long, so the maximum allowed decimal value is 65,536.
For example, if we want to set the digital alpha setpoint from scratch to a decimal value of 128, first we must
send a read instruction to register 011-d_alpha_reg (“M011”) and then overwrite its value using the
instruction “S00128”. If then we want to change once again the same register we only need to send again
the write instruction “S00000”. If we would change another different register we must proceed the same way
from the beginning. Please see the following example.
>M011
SC6006: 00000d
>S00128
SC6006: 00128d
>S00000
SC6006: 00000d
Note:
The table 8 in page 40 shows a list of available registers to write with its corresponding brief description.
36
6 INTERNAL MEMORY AND REGISTERS
Following you will find a list of some important internal software registers of SC6006 and its description. Most
of the features of SC6006 can be set using the on-board LCD menu but the operator/installer can also
access or set a great deal of internal configurations making use of RS-232 communications port described in
last chapter.
6.1 Readable registers

SC6006 can provide to the unit operator some information about its internal parameters, and settings.
Operator can access some of this registers from registers menu with the LCD (on chapter 4.3.3) but also can
access to all this registers by using the communications port, in table 2 appears the list of available-to-read
SC6006 internal registers:
Register Name Description

M000 status0 System status register 0.
M001 status1 System status register 1.
M002 p_status0 System status register 2.
M005 alpha_reg Phase angle register.
M006 u_meas_reg Voltage feedback measure register.
M007 i_meas_reg Current measure register.
M008 u_ref_reg Voltage setpoint register.
M009 i_ref_reg Current setpoint register.
M010 alpha_ext_reg Alpha setpoint register.
M011 d_alpha_reg Digital alpha setpoint register.
M016 autoconf_reg Autoconfiguration status bits.
M017 freq_reg Switching freqüency of SCR gates register.
M018 duty_reg Duty cycle of SCRs gates register.
M021 f_meas_reg Measured mains frequency register.
M022 enh_curr_reg Enhanced current measure register.
M023 delay1_reg delay for W3C mode register.
M024 delay2_reg delay for B6C mode register.
M031 autoset_reg Enable register for autoconfiguration.
M032 rmp_timeon_reg Time to on register.
M033 rmp_timeoff_reg Time to stop register.
M034 d_voltage_reg Digital voltage setpoint register.
M035 d_current_reg Digital current setpoint register.
table 2: List of readable registers.
6.1.1 status registers

The internal registers STATUS0[M000] and STATUS1[M001] are read-only registers. This registers are
internal status bits with some of the actual state or system settings as all the fault signals, ON/OFF firing
state of the unit and so on.
Following the tables with the description of some of the control bits contained in this registers.
37
M000: STATUS0 register
bit Name Description
0 on system status. ON(1)/OFF(0)
1 fault system status. Fault bit signal
2 halt halt bit signal
3 inh inhibit bit signal
4 ext_blq external block bit signal
5 sync system status. Sync bit signal
6 ov_curr system status. Overcurrent bit signal
7 N/A
8 N/A
9 N/A
10 N/A
11 N/A
12 N/A
13 N/A
14 N/A
15 N/A
table 3: bit list for status0 register.
M001: STATUS1 register

0 on_rmp on ramp activated bit
1 off_rmp off ramp activated bit
2 N/A
3 N/A
4 rotation phase rotation bit. 0 for CW.
5 mains_f mains freq. 0 for 50Hz
6 on_led ON LED bit signal
7 N/A
8 N/A
9 N/A
10 N/A
11 N/A
12 N/A
13 N/A
14 N/A
15 N/A
table 4: bit list for status1 register.
6.1.2 p_status registers

The internal registers P_STATUS0[M002], P_STATUS1[M003] and P_STATUS2[M004] are read/write
configuration registers. This registers had the masking and enable bits for many system configurations. For
example; comparison bits for normally-ON or normally-OFF blocking input signals, fault signals masking bits,
mode of operation bits, topology and live zero bits, etc.
The below tables gives a brief description of this status bit registers.
38
M002: P_STATUS0 register
0 en_on enable ON (firing) mode
1 en_fault enable fault signal
2 en_halt enable halt signal
3 en_inh enable inhibit signal
4 en_ext_blq enable external block signal
5 en_sync enable sync fault signal
6 en_ovcurr enable overcurrent fault signal
7 sw_fault enable interlock fault
8 N/A
9 N/A
10 topo0 topology bit. B6C=0, W3C=1
11 N/A
12 N/A
13 backlight enable LCD backlight
14 N/A
15 N/A
table 5: bit list for p_status0 register.

0 en_on_rmp enable soft on bit
1 en_of f_rmp enable soft off bit
2 en_auto_pw ron enable startup bit
3 en_last_state enable last state start up bit
4 N/A
5 u_meas_lz voltage feedback live zero
6 i_meas_lz current feedback live zero
7 u_ref_lz voltage setpoint live zero
8 i_ref_lz current setpoint live zero
9 alpha_lz alpha setpoint live zero
10 N/A
11 N/A
12 N/A
13 N/A
14 N/A
15 N/A
39
0 u_ref_src voltage setpoint reference bit
1 i_ref _src current setpoint reference bit
2 N/A
3 N/A
4 alpha_ref_src alpha setpoint reference bit
5 N/A
6 N/A
7 echo comm. echo mode
8 mode0 mode0 bit. PSA=0 FWS=1
9 mode1 mode1 bit. RLY=1
10 N/A
11 N/A
12 fb0 feedback mode bits:
13 fb1 00:I, 01:V, 10:IV, 11:OL
14 N/A
15 N/A
Warning note:
Take special care when attempting to change any of the configuration bits of p_status registers, if accidentally a wrong
value is written the system can stop working or malfunction.
6.2 Writable registers

In table 8 appears the list of available-to-write SC6006 internal settings registers and its brief description. It is
also specified the valid value range (decimal integer) for each register.
Register Name Description Range

M002 p_status0 System status register 2. N/A
M011 d_alpha_reg Digital alpha setpoint register. [0..1023]
M017 freq_reg Switching freqüency of SCR gates register. [10..20]
M018 duty_reg Duty cycle of SCRs gates register. [10..30]
M023 delay1_reg delay for W3C mode register. [0..400]
M024 delay2_reg delay for B6C mode register. [0..400]
M032 rmp_timeon_reg Time to on register. [1..30]
M033 rmp_timeoff_reg Time to stop register. [1..30]
M034 d_voltage_reg Digital voltage setpoint register. [0..1023]
M035 d_current_reg Digital current setpoint register. [0..1023]
M036 ov_current_reg Maximum overcurrent reference. [50..300]
table 8: list of writable registers.
Warning note:
Please do not attempt to make a writing in a register not appearing in table 8.And do not write to a register a value out of
the defined range.
40
7 INSTALLATION
In the following chapter it is given a walk-through for the most common configurations and topologies where
a SC6006 can be used, and examples on how to properly connect the SCR scheme or how the feedback
loop (V/I) can be set. Also is given some mounting recommendations.
7.1 Typical application circuits
Below there are some schematics of the most common applications (different combinations of rectifiers and
antiparallel thyristors), as well as feedback connections by shunt, transformer, etc.
The following descriptions are made separately for what concerns the firing and feedback, because they can
combine in different ways (for example, it can be done an antiparallel control (AC) taking the feedback from a
rectifier (DC), a typical application of this example would be the primary control of a transformer of a surface
treatment).
In the application examples SCR are labeled with concordance with standard output software configuration
(r-r'-s-s'-t-t').
At the end of this descriptions some advice as mounting recommendations are given, with the aim to
improve the working security and prevent possible external problems along the installation process.
7.2 Control AC/AC applications.

In AC/AC control application, SC6006 controls a three-phase group of antiparallel thyristors.
The most common cases are:
- Control in the primary:
SC6006 card controls the voltage in the primary of a transformer. Feedbacks can be for current or voltage in
the transformer primary or in the load connected in the secondary. In some cases, with applications based in
microcontrollers, PLC, etc, it’s necessary to have isolated sensors to proceed with the feedback loop.
- Direct control:
It is applied to motor start up, heating through resistor, dynamics compensation of reactive, etc.
7.2.1 W3C topology connection example

SCR1
R U
SCR2
SCR3
LOAD
S V
SCR4
SCR5
T W
SCR6
figure 26: W3C circuit connection

example.
41
7.2.2 W3C current and voltage feedback scheme
In figure 27 is shown a typical feedback connection for a W3C scheme. Current feedback made with current
transformers and voltage feedback using an auxiliar rectifier. Please note that if we use this configuration
with an auxiliary bridge connected to J12[p1]-V_REAL it not provides a galvanic isolation.
SCR1 CURRENT
TRANSF.
R U
SCR2
SCR3 CURRENT
TRANSF.
S V
SCR4
SCR5 CURRENT
T TRANSF. W
SCR6
AUX_I_T J14 11 U_REAL
J12 01
AUX_I_S J14 10
J12 02 GND
AUX_I_R J14 09 AUXILIAR
RECTIFIER
figure 27: Feedback connection W3C example.
7.2.3 Load connection types for W3C scheme

- Loads in wye connection:
To control loads in wye connection, see figure 28, the card must be synchronized with the voltages phase –
neutral, so it is very important to connect the neutral from the net to the neutral of the card (J11[pN]-
NEUTRAL).
SCR1
R
SCR2
SCR3
S
SCR4
SCR5
T
SCR6
figure 28: Load in wye circuit.
- Loads in delta circuit:

To control loads in delta connection, in case of the antiparallel thyristors are in the line, see figure, the card
must be synchronisated with the voltages phase-neutral, so it is very important to connect the neutral from
the net to the neutral of the card (J11[pN]-NEUTRAL).
42
SCR1
R
SCR2
SCR3
S
SCR4
SCR5
T
SCR6
figure 29: Load in delta circuit.
- Loads inside delta circuit or open delta circuit:

In case of the antiparallel thyristors would be connected “inside” the delta circuit, see figure 30, the card will
be configured as B6C topology.
SCR1
R
SCR2
SCR3
S
SCR4
SCR5
T
SCR6
figure 30: Load in open delta circuit.
7.2.4 M6CK and M3.2CK schemes of connection

When configuring M6CK or M3.2CK topology it is necessary to follow the diagrams of figure 31. In both
cases software output assignation is the assignation by default (r-r'-s-s'-t-t').
For M6CK configuration SC6006 must be set to work as B6C topology mode, and connect the SCR power
stack as specified in the diagram below.
For M3.2CK configuration SC6006 must be set to work as W3C topology mode, and connect the SCR power
stack as specified in the diagram below.
43
R R
T S T S
M6CK connection scheme M3.2CK connection scheme

figure 31: M6CK and M3.2CK connection schemes.
Note:
Autoset function will not be capable to determine the output connection for this topologies due its common cathode
connection. The user must check the concordance between the software output phase assignation and the wiring to the
SCRs.
7.3 Control AC/DC applications. B6C scheme.

In AC/DC control application, SC6006 controls a three-phase thyristors bridge. They have a wide range of
applications from electro-chemical processes, traction equipment, controlled power supplies, etc.
7.3.1 B6C topology connection example
SCR1 SCR3 SCR5

LOAD
R
S
T
SCR2 SCR4 SCR6
-
figure 32: B6C topology connection example.
7.3.2 DC current sense feedback using a shunt

If a shunt is used to sense the output current in a AC/DC topology then it must be checked, or decided, if the
shunt is placed on the positive ouptut terminal or on the negative one. Then the controller board should be
configured according this configuration and wired (the connections for current and voltage feedback signals)
following the next specifications.
- Shunt on positive terminal
When a shunt is used on the positive output terminal and the voltage feedback measure is done with direct
voltage input feedback J12[p1]-V_REAL, shunt negative reference must be connected to J14[p8]-GND and
its positive sensing terminal to J14[p12]-I_SHUNT. Jumper JP23 must be set in UP position as specified in
chapter 4.4.1 on page 30. So, if a current measure through shunt and a direct voltage measurement is done,
voltage and current measures must be connected as is shown in figure 33.
44
I_SHUNT SHUNT
MENU
J14 12
COARSE FINE
GND JP23
LOAD
J14 08 PWR
SC6006
U_REAL
L CD CONTRAST
J12 01 MENU
UP
C OARSE F INE
0-700 VDC
U_SENS I_SENS I_SET U_SET I _SENS U_SE NS ALPHA
SC60 06 2 3
1 2 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
figure 33: Example of connection for shunt on positive terminal.
- Shunt in negative terminal

When a shunt is used on the negative output terminal and also a direct voltage input feedback is wired,
SC6006 must be connected as is shown in figure 34.
MENU
U_REAL
J12 01
COARSE FINE
JP23
I_SHUNT
LOAD
PWR
J14 12
SC6006
LCD CONTRAST
GND MENU
DOWN
J14 08 COARSE FINE
U_SENS I_SENS I _SET U_SET I _SENS U_SE NS ALPHA
2 3
SHUNT SC60 06
1 2 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
figure 34: Example of connection for shunt on negative terminal.
Warning note:
By default jumper JP23 is in DW configuration. Only change it to UP position when using a shunt in positive terminal and
direct voltage input feedback.
7.3.3 Feedback using a current and voltage isolated sensors

Here is an example of a feedback scheme for an AC-DC application using a current isolated sensor (LA55-
P) and a voltage optoisolated sensor (SCCAVOA) from transformer in primary side and with sensor signal
outputs meeting the specifications of SC6006.
SCR1
U
R
SCR2
S SCR3
V
SCR4
T SCR5
W
SCR6
figure 35: AC/DC converter example with current and voltage feedback from transformer in primary side.
For this example circuit U_SENS and I_SENS inputs must be set through DIP-switches as 0-10 V inputs.
45
7.4 Direct drive mode with block signal
When SC6006 is operated in 'DRV' mode please note overcurrent fault and synchronism fault are
automatically disabled, and also the inhibition signal is no longer a source for halt fault.
SCR's POWER CONNECTION
SCR1
SCR2
SCR3
SCR5
SCR6
SCR4
PWR
SC6006
LCD CONTRAST
FIRING
FAULT
OV CURR
EXT BLK
MENU OK
RESET
COARSE FINE
SC6006
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
SCR1_CTL COM COM

GND GND
external block J15 14
switch or relay
SCR2_CTL
J15 15
SCR3_CTL
R S
J15 16
MAINS POWER SUPPLY
SCR's control SCR4_CTL
signals
J16 19
SCR5_CTL
J16 20
SCR6_CTL
J16 21
figure 36: 'DRV' mode recommended application circuit.
46
Following you will find a walkthrough to set up this operation mode according the circuit example given at
figure 36.
- DIRECT DRIVE MODE SETUP WALKTHROUGH:

1. Previous SC6006 operation mode configuration.
a) Power ON the board without any power connection or SCR connected to the board, just the power supply (J1).
b) Make sure the PCA is in its default factory values. Go to submenu “Restore?” and restore the default values and wait
until SC6006 reinitializes.
c) Power OFF the board.
2. Hardware test connection and configuration.

a) Connect all input signals but do not connect any SCR output power connectors.
b) Set jumpers as follows:
JP20 JP21 JP22 JP23

DW DW DW DW
c) Set on-board DIP-switches as follows:
3. Operation mode configuration.

a) Set and check that all logic inputs to 0 V and BLQ contact closed.
b) Power ON the board.
c) Go to “Mode” submenu and change to “DRV” mode.
d) Go to “Reference” and check that “Alpha”, “Voltage” and “Current” are set to “An” (Analog).
e) Go to “Live Inp.” submenu and check that all inputs are set to “0 mA”.
f) Go to “Start up” submenu and check it is in “Last” mode.
g) In “Autoset” submenu check value in option “Outputs” set as “No”.
h) Go to “Outputs” submenu and check that combination is: “ r – r' – s – s' – t – t' ”.
i) Go to Main Menu and set SC6006 in ON state.
j) At this point FAULT LED and HALT LED must be ON, the rest OFF.
4. Test correct operation.

a) Open BLQ contact. SC6006 resets FAULT and FIRING LED ON.
b) Set SCR1_CTL input (J15[p14]) to 5 V.
c) Check that SCR1 LED (D71) changes to ON following SCR1_CTL signal.
d) Repeat b) and c) points for each SCR control input.
e) Save all your software configurations: “Save all?”.
5. Hardware final set up.

a) Power OFF the SC6006 and connect all SCR output power connectors as shown in figure 36.
b) Now the board is ready to work as 6 independent multidriver mode with a block signal.
47
7.5 Mounting recommendations
7.5.1 General mounting recommendations
1- Avoid long cables in the firing system, or use twisted or shielded cables. Apply it also for the
potentiometer cables.
2- Ground the device in accordance with local regulations.
3- Make sure that the board is not in environments of strong magnetic fields, for example, high power
transformers, or apply it a conductive envelop connected to ground.
3- For use it in inductive or capacitive loads, with regular connection cycles, it’s recommended to use a
fixed resistive load (with low value), in order to avoid any kind of error during the start up process
(this is valid for all assemblies).
4- Is convenient to realize working tests with small loads (for example, bulbs or resistors), in this way if
there is any connection error will be detected without further consequences. It’s important to know
that the feedback susceptibility couldn’t be enough with loads which consumes very low current,
thus, the control operation can be wrong.
5- In AC current control applications with voltage regulation, it must be added the auxiliary rectifier
module SCCAV02, knowing that the galvanic isolation disappears with the net, otherwise use the
isolated version SCCAV02 OA.
6- Shunt elements doesn’t provide galvanic isolation in current feedback power stage. If galvanic
isolation is a requirement, it must be used isolated current sensors (Hall sensors).
7- In applications with presence of variable loads, parasitic in the net, regulations with minimums voltage
and currents, can cause non desired oscillation regulations. For this cases, please contact to our
technical department.
8- Install the device in a upright or flat position and ensure a minimum ventilation distance between
surroundings. If mounted in a cabinet ensure sufficient ventilation and always observe minimum
spacing (clearance: 150 mm above and below).
8- For specific applications, there is the possibility to realize customized software and hardware
adaptations and include auxiliary control modules, so please, don’t hesitate to ask about your
application.
7.5.2 Recommended start up procedure
CAUTION:
Before plugging the supply voltage for the control unit, be sure that the card is locked or will be start up in OFF mode
and set the regulation potentiometers to the minimum level.
1- Lock the card through external blocking switch.
2- Regulate to the minimum level all the voltage and current or alpha potentiometers or setpoints.
3- If Autoset mode is configured for check and set the mains frequency operation, the phase rotation or
outputs assignation, it will be done when the control board is powered up. Then SC6006 must be
powered after or at the same time as the power stack.
48
4- Check operation and configuration settings are correct for your application.
7.5.3 Notes about the control card in systems controlled by

microcontrollers or PLC
In those cases SC6006 is controlled by a external system, microcontroller, PLC, etc, it’s essential to guaranty
galvanic isolation between control signals and power circuits. The lack of isolation may cause a current
circulation between the power stage and the power control circuits, thus, most cases the control elements
get damaged.
The personal in charge of the design of this system should be qualified enough to manage isolation tests.
In case of doubt, please contact to our technical department where we can look for the best option.
49
8 AVAILABLE ACCESSORIES
There are available several accessories to work with the SC6006 which will be briefly described in this
section, those accessories are normally used in applications with the firing board to enhance or complete its
integration in a power converter.
8.1 SCRP6006
SCRP6006 (datasheet) is specially designed to interface our SC6006 SCR digital firing board. It provides a
neat and easy way to remotely monitor and set up SC6006 SCR controller board using its serial interface.
This panel expands the on-board LCD screen, buttons and status LEDs for mounting in a cabinet door.
Additionally provides an extension to SC6006 serial link communication port.
Typical application
8.1.1 Interfacing SC6006 with remote panel SCRP6006.

To use a remote panel interfacing SC6006 for a door cabinet e.g. on figure 37 is shown how to connect it
with SC6006. An standard DB-9 cable M to F is needed and on SC6006 the jumper 24 must be set on down
position and configure, through LCD on board, the communication with the remote panel.
SUBMENU 1.9: COM > Remote > [En / Dis]
SEMICODE
ELECTRONICA
®
PWR
Standard Male-Female DB-9 Cable.

SC6006
(Provided with SCRP6006)

LCD CONTRAST
FIRING
FAULT
OV CURR
EXT BLK
MENU OK
RESET
COARSE FINE
SC6006
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
J24 - SCRP6006 COM

JUMPER
SCRP6006 BACKSIDE SCRP6006 FRONTSIDE

figure 37: Example of connection between SC6006 and SCRP6006.
50
8.2 SCGI24
SCGI24 (datasheet) is a single-channel universal galvanical isolator well suited to interface standard 60 mV
shunt current loops and direct voltage feedback signaling with a great input range (up to 700 V).
Typical applications
8.2.1 Galvanically isolated current loop with shunt using SCGI24.

Using SCGI24 with SC6006 to provide galvanic isolation on those applications with current loop made
through a shunt. On figure 38 is depicted the scheme for a shunt mounted on positive or negative terminal
(for a B6C application e.g.) using a 4-20 mA signal for the current loop connection between SCGI24 and
SC6006.
SHUNT ON NEGATIVE TERMINAL SHUNT ON POSITIVE TERMINAL
SHUNT
POS. TERM.
POS. TERM. SCGI24 02
SCGI24 02
LOAD
LOAD
NEG. TERM.
NEG. TERM. SCGI24 03
SCGI24 03
SHUNT
TO POS. TERM.
TO NEG. TERM.
6 5 4
3 2 1
SEMICODE
ELECTRONICA
GRUESO FINO
SCGI24
CERO
®
PWR
Input : 0-60 mV
Output: 4-20 mA
SPAN
SC6006
GRUESO FINO
LCD CONTRAST
FIRING
FAULT
OV CURR
EXT BLK
MENU OK
RESET
COARSE FINE
9 8 7
12 11 10
SCGI24:9
SCGI24:8
SC6006
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 0V +24V
J16:19
J16:18
figure 38: Interfacing 60 mV shunt application with SCGI24 and 4-20 mA current loop signal.
51
8.3 SCST700
SCST700 (datasheet) is a 3-phase signal transformer for synchronism signaling which also provides a
neutral signal to the controller card in installations without neutral take which is necessary to acquire a good
synchronizing signal for SC6006. It is recommended to use it in those cases neutral connection is not
available on the installation.
Typical applications
8.3.1 Obtaining a neutral reference using SCST700 for improved synchronism

aquisition.
In those cases a neutral connection is not available or in cases the amplitude of the mains voltage where the
SC6006 card is taking the reference synchronism is under 50 VAC, it is very recommended to use SCST700
to improve synchronism acquisition for SC6006.
On figure 39 and figure 40 are represented two cases of typical connection for SCST700 where no neutral
connection available on mains. For up-to-date and more in-depth and complete information please read
SCST700 datasheet.
R
MAINS
S J11 - SC6006
SYNCHRONISM
T CONNECTOR
SCST700 J2 CONNECTOR
N T S R N T S R G1 K1 G2 K2
T S R
SEMICODE
ELECTRONICA
RG140902
N T S R
®
figure 39: Interfacing SC6006 with mains voltage from 200 to 700 VAC.
N T S R N T S R G1 K1 G2 K2
T S R
SEMICODE
ELECTRONICA
RG140902
N T S R
®
R
MAINS
S
T
figure 40: Interfacing SC6006 with mains voltage from 65 to 200 VAC.
52
9 FIRMWARE REVISIONS
Changes introduced on each firmware version of SC6006 along the initial serial number from each firmware
revision has been released are listed in the following table and described in detail below.
Please note that is possible to upgrade an old control card with the newest revision available on request.
Firmware Date Initial S/N Changes Introduced
v1.00 2013-03-20 123979 ● First firmware version released.
● Added a new mode of operation called "DRV" giving the option of fire
v1.05 2013-06-25 126553 each of the 6 channels independently from the rest and from
synchronism.
● Added Interlock function, an over current event interlocks the system

until current drops below threshold current limit and SC6006 switches
from ON state to OFF.
v1.20 2014-01-13 129519 ● Block and inhibit ON/OFF signal mode. Block and inhibit can work as
board's ON/OFF signals.
● Remote mode introduced. Enables the comunication between SC6006

and SCRP6006 remote panel.
● Improved outputs assignation algorithm.
● Saving last correct outputs assignation for use when the board is
unable to autoset outputs.
v1.25 2015-04-10 138426
● Improved given on-screen information for autoset and autoconf.
● Added new instruction set for enhancing comunication with SCRP6006

remote panel adding new remote funcionalities.
● With FWS mode now it is possible to make a PSA ramp specifying on
the time ramp the number of periods.
v1.28 2016-02-11 138440 ● Rugged behaviour on FWS with slope in for temperature treatments
with resistors controlled on primary.
● Other minor internal firmware changes introduced.
53
10 TECHNICAL SPECIFICATIONS
TECHNICAL SPECIFICATIONS
Description Symbol Notes / Test Conditions Min Typ Max Units
Input supply voltage VIN RMS 50Hz - 60Hz 195 230 480 VRMS
Input AC voltage (sync) Vsync 10 700 VRMS
Direct input voltage sense VREAL 10 700 VDC
Thyristor triggering current IOUT Vout = 5V 600 mA
Working frequency fw 50 / 60 Hz
Load Delta / wye
Topologies W3C, B6C, M6C, M3.2C, W3H, B6H, M3C…
Working modes Phase angle modulation, Full wave switch and relay mode
Protection degree IP-00
Pollution degree III
Humidity 50% Rh @ 35ºC / 70% Rh @ 20ºC
Power-to-control isolation voltage VISOp-c 50 Hz @1min 5300 VAC
SUPPLY SPECIFICATIONS
Line voltage VIN RMS ±10% 195 230 480 VRMS
Frequency range fw 47 63 Hz
Power output Pout 25 W
Typical input current Full load @ 230VAC IN 180 mA
Full load @ 400 VAC IN 130 mA
Inrush current limiting @ 230VAC IN 11,5 A
@ 400 VAC IN 20 A
Isolation between mains and output @ 1min 4000 VRMS
Isolation between secondaries @ 1min 4000 VRMS
Power supply starting time 1.5 s
System start up time without sync signals 5 s
Data at Ta = 25 °C, VIN = 230 VAC and rated v alues, unless otherwise indicated
BOARD CONNECTIONS AND CONFIGURATIONS

Description Notes / Test Conditions Units
Board configuration Jumpers, DIP switches & software configurations
Supply, control & trigger signals Plug connectors, with screw
54
BLOCK DIAGRAM
4
Line IN EMI RECTIFIERS POWER RECTIFIERS
FILTER & SWITCHING &
FILTER FILTERS
Vdd
Cathode synch. detector
GND PWM SCR drivers Pulse transformers

DETECTION
CONTROL CIRCUIT
PULSE
TRAIN 6
SHAPING
SMPS Power Supply To
CIRCUIT
SCRs
Synch block
Vcc
R, S, T IN
3
Synch C.T. feedback input
Neutral
3
Digital I/O
From mains
current
Block DSPa transformers
2 Shunt feedback input
Ext. Block
Inhibit OV. CURR.

DETECTOR
From
shunt
Fault
Fault
DSPb
Direct voltage feedback input
2
Setpoints & reference inputs

Alpha, current 7
3
& 5
Setpoints voltage RS232 From
load
Serial
References
2
Interface LCD Display 20x2 char.
To
COM
SCR FIRING BOARD
Device
INPUT REFERENCE AND FEEDBACK SIGNALS

Voltage setpoint VIN ref 0 20 mA
Current setpoint IIN ref 4 20 mA
depending of the on board DIP-
Alpha setpoint αIN ref switches conf iguration and sof tware 0 10 V
settings.
Voltage feedback signal VIN fb 0 5 V
Current feedback signal [1] IIN fb
Voltage direct feedback VIN dfb 10 700 Vpeak
Current feedback (from curr. Trans.) [1] IIN trf 0 200 mA
Current feedback (from shunt.) IIN shunt 0 60 mV
External lock NO/NC software configurab le External relay
Inhibit NO/NC software configurab le 5 V
Output fault dry relay current IK2 1.5 A
Output fault dry relay voltage VK2 250 VRMS
[1] Current inputs allows a peak input 3 times the maximum nominal current sensing.
55
PROTECTIONS AND TIMMINGS
Phase los s, sync or rotation fault
External block signal Disables thyristor f iring
Overcurrent fault Fault auto-reset sof tw are conf igurable
Max. time detect and stop phase loss tph_dly 50 60 ms
Maximum time ext. Block to stop tblk_dly 0.25 ms
Maximum time to response RS232 op. tRS232_dly 0.2 ms
Tim e to get mains sync tsync 50 cycles
SOFTWARE ADJUSTMENTS
Description Notes / Test Conditions
Maximum/minimum voltage limit 0 – 100%
Maximum/minimum current limit 0 – 100%
Soft start and stop time 1 – 30 s (independently adjustable)
Overcurrent 0 – 300%
LCD ON-BOARD SIGNAL & COM MONITORIZATION

Description
Voltage setpoint
Current setpoint All signals monitorized at on-board LCD
Alpha setpoint and through serial communications port
Voltage feedback signal
Current feedback signal
56
OUTPUT FIRING PULSE TRAIN
Description Symbol Notes/Test conditions Min Typ Max Units
Thyristor triggering current IOUT Vout = 5V 600 mA
Maximum output voltage VOUT max 7.5 V
Max transferred power to load POUT max 3 W
Output firing train frequency f OUT 1 12 25 kHz
Output firing train duty cycle Dc OUT 5 25 30 %
OUTPUT POWER vs. LOAD
3,50
3,00
2,50
2,00
Power [W]
1,50
1,00
0,50
0,00
0 2,5 5 7,5 10 12,5 15 17,5 20 22,5 25
Load [Ω]
CONFORMALS
Conformal coating MIL-1-46058, Type UR
Security EN60950-1, UL60950-1
EMC DIRECTIVE
This Thyristor power controller is intended to work as part of an industrial fixed installation and is not for itself a functional
unit destined to an end user. According 2004/108/CE directive, CE marking for this device not apply.
57
10.1 Mechanical dimensions
Description Notes/Test conditions Units
Board 225 x 170 x 45 mm
Fixations fixation holes diameter 4.5 mm
Weight (aprox) 700 gr
SEMICODE
ELECTRONICA
®
PWR
SC6006
LCD CONTRAST
FIRING
FAULT
OV CURR
EXT BLK
MENU OK
RESET
COARSE FINE
SC6006
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
(All dimensions in mm)
10.2 Connectors overview

J11 - SYNCHRONISM OUTPUT SCR FIRING
CONNECTOR CONNECTORS
SEMICODE
ELECTRONICA
®
PWR
SC6006
LCD CONTRAST
FIRING
SIGNALING LEDS
FAULT
OV CURR
EXT BLK
MENU OK
RESET
COARSE FINE
J32 - DB-9 (DCE) RS-232

COM CONNECTOR
U_SENS I_SENS I_SE T U_S ET I_SE NS U_SE NS A LPHA
SC6006
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
J1 - POWER J12 - FEEDBACK J13 - EXTERNAL BLOCK J14 - CURRENT J15 - SETPOINTS J16 - FEEDBACK AND
SUPPLY VOLTAGE AND DRY OUTPUT FAULT INPUT FEEDBACK AND INHIBIT ALPHA SETPOINT
figure 41: Connectors overview of SC6006.
58
Cost Effective Products
SEMICODE ELECTRONICA
Offers to the market a comprehensive range of products from recognized manufacturers at the best
price/quality relationship, this products are provided with a basic reference code that allows maintaining the
same product reference even if the original device manufacturer is replaced. SEMICODE product reference
has to be considered as a generic brand.
Seeking the market needs and trends, we are constantly increasing the product portfolio with new products
and suppliers, please ask for the updated information available to our local contacts.
SEMICODE products include semiconductors, passive components and accessories focused in power
electronics market.
Datasheet Annotations:
SEMICODE ELECTRONICA annotate datasheets in the top left hard corner of the front page, to indicate
product status. The annotations are as follows:
Tentative information: This is the most tentative form of information and represents a very preliminary
specification. No actual design work on the product has been started.
Preliminary Information: The product is in design and development. The datasheet represents the product
as it is understood but details may change.
Advance Information: The product design is complete and final characterisation for volume production is
well in hand.
No Annotation: The product parameters are fixed and the product is available to datasheet specification.
NOTICE: The technical data are to specify components, not to guarantee their properties.No warranty or guarantee expressed or
implied is made regarding delivery or performance. The Company reserves the right to alter without prior notice the specification of any
product. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such
methods of use will be satisfactory in a specific piece of equipment. It is the user’s responsibility to fully determine the performance and
suitability of any equipment using such information and to ensure that any publication or data used is up to date.
All brand names and product names used in this publication are trademarks, registered trademarks or trade names of their respective
owners.
© SEMICODE ELECTRONICA 2013. TECHNICAL DOCUMENTATION – NOT FOR RESALE

130320 Rev.:2.4
59

Rectificadores Controlados

Cargado por

Copyright:

Formatos disponibles

Rectificadores Controlados

Cargado por

Información del documento

Descripción original:

Título original

Derechos de autor

Formatos disponibles

Compartir este documento

Compartir o incrustar documentos

Opciones para compartir

¿Le pareció útil este documento?

¿Este contenido es inapropiado?

Copyright:

Formatos disponibles

Rectificadores Controlados

Cargado por

Copyright:

Formatos disponibles

SC6006: Operation Manual

U_SENS I_SENS I_SET U_SET I_SENS U_SENS ALPHA

1.1 Special Features

2.1 Operator and personnel requirements

2.2 Proper and intended use

2.3 Use and operation of the device

3.1 Topology configuration

3.2 Operating modes

- Phase-shift angle controller mode (PSA)

figure 1: PSA waveform example versus alpha setpoint.

figure 2: FWS waveform example versus alpha setpoint.

- Relay mode (RLY)

figure 3: Example of picket fence gate driving.

- Independent multidriver firing mode (DRV)

3.3.1 Analog or digital references / setpoints

3.3.2 Setpoints signal processing diagrams

ALPHA: [An / Dig]

figure 4: alpha setpoint signal processing diagram.

Voltage setpoint signal processing.

VOLTAGE: [An / Dig]

figure 5: Voltage setpoint signal processing diagram.

Current setpoint signal processing.

CURRENT: [An / Dig]

figure 6: Current setpoint signal processing diagram.

Current feedback signal processing.

figure 7: Current feedback signal processing diagram.

figure 8: Voltage feedback signal processing diagram.

3.5 Setpoints and feedback live input signals configuration

3.6 Control Modes

figure 9: PSA soft power on waveform example.

: SETTABLE CONF. BIT

figure 11: Logic diagram for fault signal.

Output fault dry relay

3.10 Autoset function

Mains frequency configuration:

Phase rotation autoset:

SCRs automatic output assignation:

3.11 Output assignation option

3.12 Saving all the changes and configurations

3.13 Restore default configurations

4.1 PCB connectors overview

J32 - DB-9 (DCE) RS-232

U_SENS I_SENS I_ SET U _SET I_ SENS U _SEN S ALPH A

figure 12: Connectors PCB overview.

Terminal Name Description Terminal Name Description

4.2.1 Power supply connector (J1)

4.2.2 Synchronism connector (J11)

4.2.4 External block and dry output fault connector (J13)

figure 15: Connection example diagram for J13.

4.2.5 Current input feedback connector (J14)

• Terminal 16 (INHIBIT): Inhibit input signal.

U_SENS I_SENS I_SET U_SET

Current reg. Voltage reg.

figure 17: Connection diagram example for J15.

I_SENS U_SENS ALPHA

SCRs POWER STACK

figure 19: Detail of output SCR firing connectors.

Connector Gate Cathode