Numerical Investigation of the Local Scour for Tripod Pile Foundation

Waqed H. Hassan | Zahraa Mohammad Fadhe^* | Rifqa F. Thiab | Karrar Mahdi
Civil Engineering Department, Faculty of Engineering, University of Warith Al-Anbiyaa, Kerbala 56001, Iraq
Civil Engineering Department, Faculty of Engineering, University of Kerbala, Kerbala 56001, Iraq
Corresponding Author Email: Waqed.hammed@uowa.edu.iq

OPEN ACCESS

Abstract:

This work investigates numerically a local scour moves in irregular waves around tripods. It is constructed and proven to use the numerical model of the seabed-tripod-fluid with an RNG k turbulence model. The present numerical model then examines the flow velocity distribution and scour characteristics. After that, the suggested computational model Flow-3D is a useful tool for analyzing and forecasting the maximum scour development and the flow field in random waves around tripods. The scour values affecting the foundations of the tripod must be studied and calculated, as this phenomenon directly and negatively affects the structure of the structure and its design life. The lower diagonal braces and the main column act as blockages, increasing the flow accelerations underneath them. This increases the number of particles that are moved, which in turn creates strong scouring in the area. The numerical model has a good agreement with the experimental model, with a maximum percentage of error of 10% between the experimental and numerical models. In addition, Based on dimensional analysis parameters, an empirical equation has been devised to forecast scour depth with flow depth, median size ratio, Keulegan-Carpenter (Kc), Froud number flow, and wave velocity that the results obtained in this research at various flow velocities and flow depths demonstrated that the maximum scour depth rate depended on wave height with rising velocities and decreasing particle sizes (d₅₀) and the scour depth attains its steady-current value for V_w < 0.75. As the Froude number rises, the maximum scour depth will be large.

Keywords:

local scour, tripod foundation, Flow-3D, waves

1. Introduction

New energy sources have been used by mankind since they become industrialized. The main energy sources have traditionally been timber, coal, oil, and gas, but advances in the science of new energies, such as nuclear energy, have emerged [1, 2]. Clean and renewable energy such as offshore wind has grown significantly during the past few decades. There are numerous different types of foundations regarding offshore wind turbines (OWTs), comprising the tripod, jacket, gravity foundation, suction anchor (or bucket), and monopile [3, 4]. When the water depth is less than 30 meters, Offshore wind farms usually employ the monopile type [4]. Engineers must deal with the wind’s scouring phenomenon turbine foundations when planning and designing wind turbines for an offshore environment [5]. Waves and currents generate scour, this is the erosion of soil near a submerged foundation and at its location [6]. To predict the regional scour depth at a bridge pier, Jalal et al. [7-10] developed an original gene expression algorithm using artificial neural networks. Three monopiles, one main column, and several diagonal braces connecting the monopiles to the main column make up the tripod foundation, which has more complicated shapes than a single pile. The design of the foundation may have an impact on scour depth and scour development since the foundation’s form affects the flow field [11, 12]. Stahlmann [4] conducted several field investigations. He discovered that the main column is where the greatest scour depth occurred. Under the main column is where the maximum scour depth occurs in all experiments. The estimated findings show that higher wave heights correspond to higher flow velocities, indicating that a deeper scour depth is correlated with finer silt granularity [13] recommends as the design value for a single pile. These findings support the assertion that a tripod may cause the seabed to scour more severely than a single pile. The geography of the scour is significantly more influenced by the KC value (Keulegan–Carpenter number)

The capability of computer hardware and software has made computational fluid dynamics (CFD) quite popular to predict the behavior of fluid flow in industrial and environmental applications has increased significantly in recent years [14].

Finding an acceptable piece of land for the turbine’s construction and designing the turbine pile precisely for the local conditions are the biggest challenges. Another concern related to working in a marine environment is the effect of sea waves and currents on turbine piles and foundations. The earth surrounding the turbine’s pile is scoured by the waves, which also render the pile unstable.

In this research, the main objective is to investigate numerically a local scour around tripods in random waves. It is constructed and proven to use the tripod numerical model. The present numerical model is then used to examine the flow velocity distribution and scour characteristics.

2. Numerical Model

To simulate the scouring process around the tripod foundation, the CFD code Flow-3D was employed. By using the fractional area/volume method, it may highlight the intricate boundaries of the solution domain (FAVOR).

This model was tested and validated utilizing data derived experimentally from Schendel et al. [15] and Sumer and Fredsøe [6]. 200 runs were performed at different values of parameters.

2.1 Momentum equations

The incompressible viscous fluid motion is described by the three RANS equations listed below [16]:

(1)

\frac{\partial u}{\partial t}+\frac{1}{{{V}_{F}}}\left( u{{A}_{x}}\frac{\partial u}{\partial x}+v{{A}_{y}}\frac{\partial u}{\partial y}+w{{A}_{z}}\frac{\partial u}{\partial z} \right)=-\frac{1}{\rho }\frac{\partial p}{\partial x}+{{G}_{x}}+fx

(2)

\frac{\partial v}{\partial t}+\frac{1}{{{V}_{F}}}\left( u{{A}_{x}}\frac{\partial v}{\partial x}+v{{A}_{y}}\frac{\partial v}{\partial y}+w{{A}_{z}}\frac{\partial v}{\partial z} \right)=-\frac{1}{\rho }\frac{\partial p}{\partial y}+{{G}_{y}}+\text{f}y

(3)

\frac{\partial w}{\partial t}+\frac{1}{{{V}_{F}}}\left( u{{A}_{x}}\frac{\partial w}{\partial x}+v{{A}_{y}}\frac{\partial w}{\partial y}+w{{A}_{z}}\frac{\partial w}{\partial z} \right)=-\frac{1}{\rho }\frac{\partial p}{\partial z}+{{G}_{z}}+\text{fz}

where, respectively, u, v, and w represent the x, y, and z flow velocity components; volume fraction (VF), area fraction (A_i; I=x, y, z), water density (f), viscous force (f_i), and body force (G_i) are all used in the formula.

2.2 Model of turbulence

Several turbulence models would be combined to solve the momentum equations. A two-equation model of turbulence is the RNG k-model, which has a high efficiency and accuracy in computing the near-wall flow field. Therefore, the flow field surrounding tripods was captured using the RNG k-model.

2.3 Model of sediment scour

2.3.1 Induction and deposition

Eq. (4) can be used to determine the particle entrainment lift velocity [17].

(4)

{{u}_{lift,i}}={{\alpha }_{i}}{{n}_{s}}d_{*}^{0.3}{{\left( \theta -{{\theta }_{cr}} \right)}^{1.5}}\sqrt{\frac{\parallel g\parallel {{d}_{i}}\left( {{\rho }_{i}}-{{\rho }_{f}} \right)}{{{\rho }_{f}}}}

α𝛼_i is the Induction parameter, n_s the normal vector is parallel to the seafloor, and for the present numerical model, n_s=(0,0,1), θ𝜃_cr is the essential Shields variable, g is the accelerated by gravity, d_i is the size of the particles, ρ_i is species density in beds, and d_∗ The diameter of particles without dimensions; these values can be obtained in Eq. (5).

(5)

{{d}_{*}}={{d}_{i}}{{\left( \frac{\parallel g\parallel {{\rho }_{f}}\left( {{\rho }_{i}}-{{\rho }_{f}} \right)}{\mu _{f}^{2}} \right)}^{1/3}}

μ𝜇_f is this equation a dynamic viscosity of the fluid. c_r was determined from an equation based on Soulsby [18].

(6)

{{\theta }_{cr}}=\frac{0.3}{1+1.2{{d}_{*}}}+0.055\left[ 1-\text{exp}\left( -0.02{{d}_{*}} \right) \right]

The equation was used to determine how quickly sand particles set Eq. (7):

(7)

{{\mathbf{u}}_{\text{nsettling},i}}=\frac{{{v}_{f}}}{{{d}_{i}}}\left[ {{\left( {{10.36}^{2}}+1.049d_{*}^{3} \right)}^{0.5}}-10.36 \right]

v_f stands for fluid kinematic viscosity.

2.3.2 Transportation for bed loads

Van Rijn [19] states that the speed of bed load conveyance was determined as:

(8)

{{~}_{\text{bedload},i}}=\frac{{{q}_{b,i}}}{{{\delta }_{i}}{{c}_{b,i}}{{f}_{b}}}

f_b is the essential particle packing percentage, q_b, i is the bed load transportation rate, and c_b, I the percentage of sand by volume i. These variables can be found in Eq. (9), Eq. (10), f_b, δ𝛿_i the bed load thickness.

(9)

{{q}_{b,i}}=8{{\left[ \parallel g\parallel \left( \frac{{{\rho }_{i}}-{{\rho }_{f}}}{{{\rho }_{f}}} \right)d_{i}^{3} \right]}^{\frac{1}{2}}}

(10)

{{\delta }_{i}}=0.3d_{*}^{0.7}{{\left( \frac{\theta }{{{\theta }_{cr}}}-1 \right)}^{0.5}}{{d}_{i}}

In this paper, after the calibration of numerous trials, the selection of parameters for sediment scour is crucial. Maximum packing fraction is 0.64 with a shields number of 0.05, entrainment coefficient of 0.018, the mass density of 2650, bed load coefficient of 12, and entrainment coefficient of 0.01.

3. Model Setup

To investigate the scour characteristics near tripods in random waves, the seabed-tripod-fluid numerical model was created as shown in Figure 1. The tripod basis, a seabed, and fluid and porous medium were all components of the model. The seabed was 240 meters long, 40 meters wide, and three meters high. It had a median diameter of d₅₀ and was composed of uniformly fine sand. The 2.5-meter main column diameter D. The base of the main column was three dimensions above the original seabed. The center of the seafloor was where the tripod was, 130 meters from the offshore and 110 meters from the onshore. To prevent wave reflection, the porous media were positioned above the seabed on the onshore side.

image013.png

Figure 1. An illustration of the numerical model for the seabed-tripod-fluid

3.1 Generation of meshes

Figure 2 displays the model’s mesh for the Flow-3D software grid. The current model made use of two different mesh types: global mesh grid and nested mesh grid. A mesh grid with the following measurements was created by the global hexahedra mesh grid: 240m length, 40m width, and 32m height. Around the tripod, a finer nested mesh grid was made, with dimensions of 0 to 32m on the z-axis, 10 to 30 m on the x-axis, and 25 to 15 m on the y-axis. This improved the calculation’s precision and mesh quality.

image014.png

Figure 2. The mesh block sketch

3.2 Conditional boundaries

To increase calculation efficiency, the top side, The model’s two x-z plane sides, as well as the symmetry boundaries, were all specified. For u, v, w=0, the bottom boundary wall was picked. The offshore end of the wave boundary was put upstream. For the wave border, random waves were generated using the wave spectrum from the Joint North Sea Wave Project (JONSWAP). Boundary conditions are shown in Figure 3.

image015.png

Figure 3. Boundary conditions of the typical problem

The wave spectrum peak enhancement factor (=3.3 for this work) and can be used to express the unidirectional JONSWAP frequency spectrum.

3.3 Mesh sensitivity

Before doing additional research into scour traits and scour depth forecasting, mesh sensitivity analysis is essential. Three different mesh grid sizes were selected for this section: Mesh 1 has a 0.45 by 0.45 nested fine mesh and a 0.6 by 0.6 global mesh size. Mesh 2 has a 0.4 global mesh size and a 0.35 nested fine mesh size, while Mesh 3 has a 0.25 global mesh size and a nested fine mesh size of 0.15. Comparing the relative fine mesh size (such as Mesh 2 or Mesh 3) to the relatively coarse mesh size (such as Mesh 1), a larger scour depth was seen; this shows that a finer mesh size can more precisely represent the scouring and flow field action around a tripod. Significantly, a lower mesh size necessitates a time commitment and a more difficult computer configuration. Depending on the sensitivity of the mesh guideline utilized by Pang et al., when Mesh 2 is applied, the findings converge and the mesh size is independent [20]. In the next sections, scouring the area surrounding the tripod was calculated using Mesh 2 to ensure accuracy and reduce computation time. The working segment generates a total of 14, 800,324 cells.

3.4 Model validation

Comparisons between the predicted outcomes from the current model and to confirm that the current numerical model is accurate and suitably modified, experimental data from Sumer and Fredsøe [6] and Schendel et al. [15] were used. For the experimental results of Run 05, Run 15, and Run 22 from Sumer and Fredsøe [6], the experimental A9, A13, A17, A25, A26, and A27 results from Schendel et al. [15], and the numerical results from the current model are shown in Figure 4. The present model had d₅₀=0.051cm, the height of the water wave(h)=10m, and wave velocity=0.854 m.s^-1.

image016.png

Figure 4. Cell size effect

image017.png

Figure 5. Comparison of the present study’s maximum scour depth with that authored by Sumer and Fredsøe [6] and Schendel et al. [15]

According to Figure 5, the highest discrepancy between the numerical results and experimental data is about 10%, showing that overall, there is good agreement between them. The ability of the current numerical model to accurately depict the scour process and forecast the maximum scour depth (S) near foundations is demonstrated by this. Errors in the simulation were reduced by using the calibrated values of the parameter. Considering these results, a suggested simulated scouring utilizing a Flow-3D numerical model is confirmed as a superior way for precisely forecasting the maximum scour depth near a tripod foundation in random waves.

3.5 Dimensional analysis

The variables found in this study as having the greatest impacts, variables related to flow, fluid, bed sediment, flume shape, and duration all had an impact on local scouring depth (t). Hence, scour depth (S) can be seen as a function of these factors, shown as:

(11)

S=f\left(\rho, v, V, h, g, \rho s, d_{50}, \sigma g, V_w, D, d, T_v, t\right)

With the aid of dimensional analysis, the 14-dimensional parameters in Eq. (11) were reduced to 6 dimensionless variables using Buckingham’s -theorem. D, V, and were therefore set as repetition parameters and others as constants, allowing for the ignoring of their influence. Eq. (12) thus illustrates the relationship between the effect of the non-dimensional components on the depth of scour surrounding a tripod base.

(12)

\frac{S}{D}=f\left(\frac{h}{D}, \frac{d 50}{D}, \frac{V}{V W}, F r, K c\right)

where, SD𝑆𝐷 are scoured depth ratio, VVw𝑉𝑉𝑤 is flow wave velocity, d50D𝑑50𝐷 median size ratio, $Fr representstheFroudnumber,and𝑟𝑒𝑝𝑟𝑒𝑠𝑒𝑛𝑡𝑠𝑡ℎ𝑒𝐹𝑟𝑜𝑢𝑑𝑛𝑢𝑚𝑏𝑒𝑟,𝑎𝑛𝑑Kc$ is the Keulegan-Carpenter.

4. Result and Discussion

4.1 Development of scour

Similar to how the physical model was used, this numerical model was also used. The numerical model’s boundary conditions and other crucial variables that directly influence the outcomes were applied (flow depth, median particle size (d₅₀), and wave velocity). After the initial 0-300 s, the scour rate reduced as the scour holes grew quickly. The scour depths steadied for about 1800 seconds before reaching an asymptotic value. The findings of scour depth with time are displayed in Figure 6.

4.2 Features of scour

Early on (t=400s), the scour hole began to appear beneath the main column and then began to extend along the diagonal bracing connecting to the wall-facing pile. Gradually, the geography of the scour; of these results is similar to the experimental observations of Stahlmann [4] and Aminoroayaie Yamini et al. [1]. As the waves reached the tripod, there was an enhanced flow acceleration underneath the main column and the lower diagonal braces as a result of the obstructing effects of the structural elements. More particles are mobilized and transported due to the enhanced near-bed flow velocity, it also increases bed shear stress, turbulence, and scour at the site. In comparison to a single pile, the main column and structural components of the tripod have a significant impact on the flow velocity distribution and, consequently, the scour process and morphology. The main column and seabed are separated by a gap, therefore the flow across the gap may aid in scouring. The scour hole first emerged beneath the main column and subsequently expanded along the lower structural components, both Aminoroayaie Yamini et al. [1] and Stahlmann [4] made this claim. Around the tripod, there are several different scour morphologies and the flow velocity distribution as shown in Figures 7 and 8.

image023.png

Figure 6. Results of scour depth with time

image024.png

image025.png

image026.png

image027.png

Figure 7. The sequence results of scour depth around tripod development (reached to steady state) simulation time

image028.png

image029.png

image030.png

image031.png

Figure 8. Random waves of flow velocity distribution around a tripod

4.3 Wave velocity’s (V_w) impact on scour depth

In this study’s section, we looked at how variations in wave current velocity affected the scouring depth. Bed scour pattern modification could result from an increase or decrease in waves. As a result, the backflow area produced within the pile would become stronger, which would increase the depth of the sediment scour. The quantity of current turbulence is the primary cause of the relationship between wave height and bed scour value. The current velocity has increased the extent to which the turbulence energy has changed and increased in strength now present. It should be mentioned that in this instance, the Jon swap spectrum random waves are chosen. The scour depth attains its steady-current value for Vw<0.75, Figure 9 (a) shows that effect. When (V) represents the mean velocity=0.5 m.s^-1.

image032.png

(a)

image033.png

(b)

image034.png

(c)

image035.png

(d)

Figure 9. Main effects on maximum scour depth (S_max) as a function of column diameter (D)

4.4 Impact of a median particle (d₅₀) on scour depth

In this section of the study, we looked into how variations in particle size affected how the bed profile changed. The values of various particle diameters are defined in the numerical model for each run numerical modeling, and the conditions under which changes in particle diameter have an impact on the bed scour profile are derived. Based on Figure 9 (b), the findings of the numerical modeling show that as particle diameter increases the maximum scour depth caused by wave contact decreases. When (d₅₀) is the diameter of Sediment (d₅₀). The Shatt Al-Arab soil near Basra, Iraq, was used to produce a variety of varied diameters.

4.5 Impact of wave height and flow depth (h) on scour depth

One of the main elements affecting the scour profile brought on by the interaction of the wave and current with the piles of the wind turbines is the height of the wave surrounding the turbine pile causing more turbulence to develop there. The velocity towards the bottom and the bed both vary as the turbulence around the pile is increased, modifying the scour profile close to the pile. According to the results of the numerical modeling, the depth of scour will increase as water depth and wave height in random waves increase as shown in Figure 9 (c).

4.6 Froude number’s (Fr) impact on scour depth

No matter what the spacing ratio, the Figure 9 shows that the Froude number rises, and the maximum scour depth often rises as well increases in Figure 9 (d). Additionally, it is crucial to keep in mind that only a small portion of the findings regarding the spacing ratios with the smallest values. Due to the velocity acceleration in the presence of a larger Froude number, the range of edge scour downstream is greater than that of upstream. Moreover, the scouring phenomena occur in the region farthest from the tripod, perhaps as a result of the turbulence brought on by the collision of the tripod’s pile. Generally, as the Froude number rises, so does the deposition height and scour depth.

4.7 Keulegan-Carpenter (KC) number

The geography of the scour is significantly more influenced by the KC value. Greater KC causes a deeper equilibrium scour because an increase in KC lengthens the horseshoe vortex’s duration and intensifies it as shown in Figure 10.

The result can be attributed to the fact that wave superposition reduced the crucial KC for the initiation of the scour, particularly under small KC conditions. The primary variable in the equation used to calculate This is the depth of the scouring hole at the bed. The following expression is used to calculate the Keulegan-Carpenter number:

Kc=Vw∗TpD𝐾𝑐=𝑉𝑤∗𝑇𝑝𝐷 (13)

where, the wave period is T_p and the wave velocity is shown by V_w_.

image037.png

Figure 10. Relationship between the relative maximum scour depth and KC

5. Conclusion

(1) The existing seabed-tripod-fluid numerical model is capable of faithfully reproducing the scour process and the flow field around tripods, suggesting that it may be used to predict the scour around tripods in random waves.

(2) Their results obtained in this research at various flow velocities and flow depths demonstrated that the maximum scour depth rate depended on wave height with rising velocities and decreasing particle sizes (d₅₀).

(3) A diagonal brace and the main column act as blockages, increasing the flow accelerations underneath them. This raises the magnitude of the disturbance and the shear stress on the seafloor, which in turn causes a greater number of particles to be mobilized and conveyed, as a result, causes more severe scour at the location.

(4) The Froude number and the scouring process are closely related. In general, as the Froude number rises, so does the maximum scour depth and scour range. The highest maximum scour depth always coincides with the bigger Froude number with the shortest spacing ratio.

Since the issue is that there aren’t many experiments or studies that are relevant to this subject, therefore we had to rely on the monopile criteria. Therefore, to gain a deeper knowledge of the scouring effect surrounding the tripod in random waves, further numerical research exploring numerous soil, foundation, and construction elements as well as upcoming physical model tests will be beneficial.

Nomenclature

CFD	Computational fluid dynamics
FAVOR	Fractional Area/Volume Obstacle Representation
VOF	Volume of Fluid
RNG	Renormalized Group
OWTs	Offshore wind turbines
Greek Symbols
ε, ω	Dissipation rate of the turbulent kinetic energy, m²s^-3
Subscripts
d₅₀	Median particle size
V_f	Volume fraction
G_T	Turbulent energy of buoyancy
K_T	Turbulent velocity
P_T	Kinetic energy of the turbulence
Α_i	Induction parameter
n_s	Induction parameter
ΘΘ_cr	The essential Shields variable
D_i	Diameter of sediment
d_∗	The diameter of particles without dimensions
µ_f	Dynamic viscosity of the fluid
q_b,_i	The bed load transportation rate
C_s,i	Sand particle’s concentration of mass
D	Diameter of pile
D_f	Diffusivity
D	Diameter of main column
Fr	Froud number
Kc	Keulegan–Carpenter number
G	Acceleration of gravity g
H	Flow depth
Vw	Wave Velocity
V	Mean Velocity
Tp	Wave Period
S	Scour depth

References

[1] Aminoroayaie Yamini, O., Mousavi, S.H., Kavianpour, M.R., Movahedi, A. (2018). Numerical modeling of sediment scouring phenomenon around the offshore wind turbine pile in marine environment. Environmental Earth Sciences, 77: 1-15. https://doi.org/10.1007/s12665-018-7967-4

[2] Hassan, W.H., Hashim, F.S. (2020). The effect of climate change on the maximum temperature in Southwest Iraq using HadCM3 and CanESM2 modelling. SN Applied Sciences, 2(9): 1494. https://doi.org/10.1007/s42452-020-03302-z

[3] Fazeres-Ferradosa, T., Rosa-Santos, P., Taveira-Pinto, F., Pavlou, D., Gao, F.P., Carvalho, H., Oliveira-Pinto, S. (2020). Preface: Advanced research on offshore structures and foundation design part 2. In Proceedings of the Institution of Civil Engineers-Maritime Engineering. Thomas Telford Ltd, 173(4): 96-99. https://doi.org/10.1680/jmaen.2020.173.4.96

[4] Stahlmann, A. (2013). Numerical and experimental modeling of scour at foundation structures for offshore wind turbines. In ISOPE International Ocean and Polar Engineering Conference. ISOPE, pp. ISOPE-I.

[5] Petersen, T.U., Sumer, B.M., Fredsøe, J. (2014). Edge scour at scour protections around offshore wind turbine foundations. In 7th International Conference on Scour and Erosion. CRC Press, pp. 587-592.

[6] Sumer, B.M., Fredsøe, J. (2001). Scour around pile in combined waves and current. Journal of Hydraulic Engineering, 127(5): 403-411. https://doi.org/10.1061/(ASCE)0733-9429(2001)127:5(403)

[7] Jalal, H.K., Hassan, W.H. (2020). Effect of bridge pier shape on depth of scour. In IOP Conference Series: Materials Science and Engineering. IOP Publishing, 671(1): 012001. https://doi.org/10.1088/1757-899X/671/1/012001

[8] Hassan, W.H., Jalal, H.K. (2021). Prediction of the depth of local scouring at a bridge pier using a gene expression programming method. SN Applied Sciences, 3(2): 159. https://doi.org/10.1007/s42452-020-04124-9

[9] Jalal, H.K., Hassan, W.H. (2020). Three-dimensional numerical simulation of local scour around circular bridge pier using Flow-3D software. In IOP Conference Series: Materials Science and Engineering. IOP Publishing, 745(1): 012150. https://doi.org/10.1088/1757-899X/745/1/012150

[10] Hassan, W.H., Attea, Z.H., Mohammed, S.S. (2020). Optimum layout design of sewer networks by hybrid genetic algorithm. Journal of Applied Water Engineering and Research, 8(2): 108-124. https://doi.org/10.1080/23249676.2020.1761897

[11] Hassan, W.H., Hussein, H.H., Alshammari, M.H., Jalal, H.K., Rasheed, S.E. (2022). Evaluation of gene expression programming and artificial neural networks in PyTorch for the prediction of local scour depth around a bridge pier. Results in Engineering, 13: 100353. https://doi.org/10.1016/j.rineng.2022.100353

[12] Hassan, W.H., Hh, H., Mohammed, S.S., Jalal, H.K., Nile, B.K. (2021). Evaluation of gene expression programming to predict the local scour depth around a bridge pier. Journal of Engineering Science and Technology, 16(2): 1232-1243. https://doi.org/10.1016/j.rineng.2022.100353

[13] Nerland, C. (2010). Offshore wind energy: Balancing risk and reward. In Proceedings of the Canadian Wind Energy Association’s 2010 Annual Conference and Exhibition, Canada, p. 2000.

[14] Hassan, W.H., Nile, B.K., Mahdi, K., Wesseling, J., Ritsema, C. (2021). A feasibility assessment of potential artificial recharge for increasing agricultural areas in the kerbala desert in Iraq using numerical groundwater modeling. Water, 13(22): 3167. https://doi.org/10.3390/w13223167

[15] Schendel, A., Welzel, M., Schlurmann, T., Hsu, T.W. (2020). Scour around a monopile induced by directionally spread irregular waves in combination with oblique currents. Coastal Engineering, 161: 103751. https://doi.org/10.1016/j.coastaleng.2020.103751

[16] Yakhot, V., Orszag, S.A. (1986). Renormalization group analysis of turbulence. I. Basic theory. Journal of Scientific Computing, 1(1): 3-51. https://doi.org/10.1007/BF01061452

[17] Mastbergen, D.R., Van Den Berg, J.H. (2003). Breaching in fine sands and the generation of sustained turbidity currents in submarine canyons. Sedimentology, 50(4): 625-637. https://doi.org/10.1046/j.1365-3091.2003.00554.x

[18] Soulsby, R. (1997). Dynamics of marine sands. https://doi.org/10.1680/doms.25844

[19] Van Rijn, L.C. (1984). Sediment transport, part I: Bed load transport. Journal of Hydraulic Engineering, 110(10): 1431-1456. https://doi.org/10.1061/(ASCE)0733-9429(1984)110:10(1431)

[20] Pang, A.L.J., Skote, M., Lim, S.Y., Gullman-Strand, J., Morgan, N. (2016). A numerical approach for determining equilibrium scour depth around a mono-pile due to steady currents. Applied Ocean Research, 57: 114-124. https://doi.org/10.1016/j.apor.2016.02.010

Local Scour Depth Around Bridge Piers: Performance Evaluation of Dimensional Analysis-based Empirical Equations and AI Techniques

Abstract

Artificial Intelligence (AI) techniques, such as Artificial Neural Networks (ANN) and Adaptive Neuro-Fuzzy Inference Systems (ANFIS), and dimensional analysis-based empirical equations (DAEEs), can estimate scour depth around bridge piers. AI’s accuracy depends on various architectures, while DAEEs’ performance depends on experimental data. This study evaluated the performance of AI and DAEEs for scour depth estimation using flow velocity, depth, size of bed sediment, critical approach velocity, and pier width. The data from a smooth rectangular (20 m × 1 m) flume and a high-precision particle image velocimetry to study the flow structure around the pier – width: 1.5 – 91.5 cm evaluated DAEEs. Various ANNs (5, 10, and 15 neurons), double layer (DL) and triple layers (TL), and different ANFIS settings were trained, tested, and verified. The Generalized Reduced Gradient optimization identified the parameters of DAEEs, and Nash–Sutcliffe efficiency (NSE) and Mean Square Error (MSE) evaluated the performance of different models. The study revealed that DL ANN-3 with 10 neurons (NSE = 0.986) outperformed ANFIS, other ANN (ANN1, ANN2, ANN4 & ANN5) models, and empirical equations with NSE values between 0.76 and 0.983. The study found pier dimensions to be the most influential parameter for pier scour.

This is a preview of subscription content, log in via an institution to check access.

Abdul Razzaq Ghumman, Husnain Haider, Ibrahim Saleh Al Salamah, Md. Shafiquzzaman, Abdullah Alodah, Mohammad Alresheedi, Rashid Farooq, Afzal Ahmed & Ghufran Ahmed Pasha

Prediction of local scour around bridge piers using the ANFIS method

Article 18 September 2015

Live-Bed Scour Depth Modelling Around the Bridge Pier Using ANN-PSO, ANFIS, MARS, and M5Tree

Article 22 May 2024

Artificial Intelligence Modeling for Scour Depth Prediction Upstream of Bridge Piers

Article 08 November 2023

References

Abadie J (1969) Generalization of the Wolfe reduced gradient method to the case of non-linear constraints. Optimization, 37–47
Abd El-Hady Rady R (2020) Prediction of local scour around bridge piers: Artificial-intelligence-based modeling versus conventional regression methods. Applied Water Science 10(2):57, DOI: https://doi.org/10.1007/s13201-020-1140-4 Article Google Scholar
Afzali SH (2016) New model for determining local scour depth around piers. Arababian Journal of Science and Engineering 41(10):3807–3815, DOI: https://doi.org/10.1007/s13369-015-1983-4 Article Google Scholar
Akhlaghi E, Babarsad MS, Derikvand EM, Abedini M (2020) Assessment the effects of different parameters to rate scour around single piers and pile groups: A review. Archives of Computational Methods in Engineering 27(1):183–197, DOI: https://doi.org/10.1007/s11831-018-09304-w Article Google Scholar
Alharbi S, Mills G (2022) Assessment of exposure to flash flooding in an arid environment: A case study of the jeddah city neighborhood abruq ar rughamah, saudi arabia. In: Wadi Flash Floods: Challenges and Advanced Approaches for Disaster Risk Reduction. Springer Nature Singapore, 383–397Chapter Google Scholar
Annad M, Lefkir A (2022) Analytic network process for local scour formula ranking with parametric sensitivity analysis and soil class clustering. Water Supply 22(11):8287–8304, DOI: https://doi.org/10.2166/ws.2022.357 Article Google Scholar
Annad M, Lefkir A, Mammar-kouadri M, Bettahar I (2021) Development of a local scour prediction model clustered by soil class. Water Practice & Technology 16(4):1159–1172, DOI: https://doi.org/10.2166/wpt.2021.065 Article Google Scholar
Arifin F, Robbani H, Annisa T, Ma’Arof N (2019) Variations in the number of layers and the number of neurons in artificial neural networks: Case study of pattern recognition. Journal of Physics: Conference Series 1413(1):12016, DOI: https://doi.org/10.1088/1742-6596/1413/1/012016 Google Scholar
Arneson LA, Zevenbergen LW, Lagasse PF, Clopper PE (2012) Evaluating scour at bridges. Report No. FHWA-HIF-12-003 HEC-18, National Highway Institute, Arlington, VA, USAGoogle Scholar
Azamathulla HM, Ghani AA, Zakaria NA, Guven A (2010) Genetic programming to predict bridge pier scour. Journal of Hydraulic Engineering 136(3):165, DOI: https://doi.org/10.1061/(ASCE)HY1943-7900.0000133 Article Google Scholar
Benedict ST, Caldwell AW (2014) A pier-scour database: 2427 Field and Laboratory Measurements of Pier Scour, Data Series No. 845, US Department of the Interior, US Geol. Surv. Reston, VA, USAGoogle Scholar
Briaud JL, Ting FCK, Chen HC, Gudavalli R, Perugu S, Wei G (1999) SRICOS: Prediction of scour rate in cohesive soils at bridge piers. Journal of Geotechnical and Geoenvironmental Engineering 125(4): 237–246, DOI: https://doi.org/10.1061/(ASCE)1090-0241(1999)125:4(237)Article Google Scholar
Cao J, Chen J, Zhu D, Wei S (2021) Evaluation of local scour calculation equations for bridge piers in sandy riverbed. IOP Conference Series: Earth and Environmental Science 692(4):042022, DOI: https://doi.org/10.1088/1755-1315/692/4/042022 Google Scholar
Chabert J (1956) Etude des affouillements autour des piles de ponts. Laboratoire National d’Hydraulique, ChatouGoogle Scholar
Chavan R, Gualtieri P, Kumar B (2019) Turbulent flow structures and scour hole characteristics around circular bridge piers over nonuniform sand bed channels with downward seepage. Water 11(8):1580, DOI: https://doi.org/10.3390/w11081580 Article Google Scholar
Chavan R, Kumar B (2020) Downward seepage effects on dynamics of scour depth and migrating dune-like bedforms at tandem piers. Canadian Journal of Civil Engineering 47(1):13–24, DOI: https://doi.org/10.1139/cjce-2017-0640 Article Google Scholar
Choi SU, Choi S (2022) Prediction of local scour around bridge piers in the cohesive bed using support vector machines. KSCE Journal of Civil Engineering 26(5):2174–2182, DOI: https://doi.org/10.1007/s12205-022-1803-9 Article Google Scholar
Ciancimino A, Anastasopoulos I, Foti S, Gajo A (2022) Numerical modelling of the effects of foundation scour on the response of a bridge pier. Acta Geotech 17(9):3697–3717, DOI: https://doi.org/10.1007/s11440-022-01591-9 Article Google Scholar
Cikojević A, Gilja G, Kuspilić N (2019) Sensitivity analysis of empirical equations applicable on bridge piers in sand-bed rivers, Proceedings of the 16th International Symposium on Water Management and Hydraulic Engineering, September 5–7, Skopje, Republic of Macedonia
Dang NM, Tran Anh D, Dang TD (2021) ANN optimized by PSO and Firefly algorithms for predicting scour depths around bridge piers, Engineering with Computers 37(1):293–303, DOI: https://doi.org/10.1007/s00366-019-00824-y Article Google Scholar
Dimitriadis P, Koutsoyiannis D, Iliopoulou T, Papanicolaou P (2021) A global-scale investigation of stochastic similarities in marginal distribution and dependence structure of key hydrological-cycle processes. Hydrology 8(2):59, DOI: https://doi.org/10.3390/hydrology8020059 Article Google Scholar
Ettema R (1980) Scour at bridge piers: A report submitted to the National Roads Board. PhD Thesis, The University of Auckland, Auckland, New ZealandGoogle Scholar
Farooq R, Ghumman AR, Ahmed A, Latif A, Masood A (2021) Performance evaluation of scour protection around a bridge pier through experimental approach. Tehnički Vjesnik 28(6):1975–1982, DOI: https://doi.org/10.17559/TV-20200213211932 Google Scholar
Fattah MY, Hassan WH, Rasheed SE (2018) Behavior of flexible buried pipes under geocell reinforced subbase subjected to repeated loading. International Journal of Geotechnical Earthquake Engineering 9(1):22–41, DOI: https://doi.org/10.4018/IJGEE.2018010102 Article Google Scholar
FHWA (1998) Recording and coding guide for the structural inventory and appraisal of the nations’ bridges. Report No. FHWA-PD-96-001, US Department of Transportation, Federal Highway Administration. Office of Engineering, Washigton DC, USAGoogle Scholar
Fouli H, Elsebaie IH (2016) Reducing local scour at bridge piers using an upstream subsidiary triangular pillar. Arabian Journal of Geosciences 9(12):598, DOI: https://doi.org/10.1007/s12517-016-2615-3 Article Google Scholar
Hafez YI (2016) Mathematical modeling of local scour at slender and wide bridge piers. Journal of Fluids 2016:1–19, DOI: https://doi.org/10.1155/2016/4835253 Article Google Scholar
Hamidifar H, Zanganeh-Inaloo F, Carnacina I (2021) Hybrid scour depth prediction equations for reliable design of bridge piers. Water 13(15):2019, DOI: https://doi.org/10.3390/w13152019 Article Google Scholar
Hassan WH, Hussein HH, Alshammari MH, Jalal HK, Rasheed SE (2022) Evaluation of gene expression programming and artificial neural networks in PyTorch for the prediction of local scour depth around a bridge pier. Results in Engineering 13:100353, DOI: https://doi.org/10.1016/j.rineng.2022.100353 Article Google Scholar
Hassan WH, Jalal HK (2021) Prediction of the depth of local scouring at a bridge pier using a gene expression programming method. SN Applied Sciences 3(2):159, DOI: https://doi.org/10.1007/s42452-020-04124-9 Article Google Scholar
Huang J, Yu H, Guan X, Wang G, Guo R (2016) Accelerated dryland expansion under climate change. Nature Climate Change 6(2):166–171, DOI: https://doi.org/10.1038/nclimate2837 Article Google Scholar
Imhof D (2004) Risk assessment of existing bridge structures. PhD Thesis, University of Cambridge, Cambridge, UKGoogle Scholar
Jalal HK, Hassan WH (2020) Three-dimensional numerical simulation of local scour around circular bridge pier using Flow-3D software. IOP Conference Series: Materials Science and Engineering 745(1): 12150, DOI: https://doi.org/10.1088/1757-899X/745/1/012150 Article Google Scholar
Khassaf SI, Ahmed SI (2021) Development an empirical formula to calculate the scour depth at different shapes of non-uniform piers. Journal of Physics: Conference Series 1973(1):012179, DOI: https://doi.org/10.1088/1742-6596/1973/1/012179 Google Scholar
Lasdon LS, Waren AD, Jain A, Ratner M (1978) Design and testing of a generalized reduced gradient code for non-linear programming. ACM Transactions on Mathematical Software 4(1):34–50, DOI: https://doi.org/10.1145/355769.355773 Article Google Scholar
Liang F, Wang C, Yu X (2019) Performance of existing methods for estimation and mitigation of local scour around bridges: Case studies. Journal of Performance of Constructed Facilities 33(6):4019060, DOI: https://doi.org/10.1061/(ASCE)CF.1943-5509.0001329 Article Google Scholar
Lin C, Han J, Bennett C, Parsons RL (2014) Case history analysis of bridge failures due to scour. Climatic Effects on Pavement and Geotechnical Infrastructure 2014:204–216, DOI: https://doi.org/10.1061/9780784413326.021 Article Google Scholar
Maddison B (2012) Scour failure of bridges. Proceedings of the Institution of Civil Engineers-forensic Engineering 165(1):39–52, DOI: https://doi.org/10.1680/feng.2012.165.1.39 Article Google Scholar
Melville BW (1984) Live-bed scour at bridge piers. Journal of Hydraulic Engineering 110(9):1234–1247, DOI: https://doi.org/10.1061/(ASCE)0733-9429(1984)110:9(1234)Article Google Scholar
Mohammadpour R (2017) Prediction of local scour around complex piers using GEP and M5-Tree. Arabian Journal of Geosciences 10(18):416, DOI: https://doi.org/10.1007/s12517-017-3203-x Article Google Scholar
Mohammadpour R, Ghani AA, Sabzevari T, Fared Murshed M (2021) Local scour around complex abutments. ISH Journal of Hydraulic Engineering 27(1):165–173, DOI: https://doi.org/10.1080/09715010.2019.1607783 Article Google Scholar
Moriasi DN, Arnold JG, Van Liew MW, Bingner RL, Harmel RD, Veith TL (2007) Model evaluation guidelines for systematic quantification of accuracy in watershed simulations. Transactions of ASABE 50(3): 885–900, DOI: https://doi.org/10.13031/2013.23153 Article Google Scholar
Moussa YAM (2013) Modeling of local scour depth downstream hydraulic structures in trapezoidal channel using GEP and ANNs. Ain Shams Engineering Journal 4(4):717–722, DOI: https://doi.org/10.1016/j.asej.2013.04.005 Article Google Scholar
Muzzammil M, Alama J, Danish M (2015) Scour prediction at bridge piers in cohesive bed using gene expression programming. Aquatic Procedia 4:789–796, DOI: https://doi.org/10.1016/j.aqpro.2015.02.098 Article Google Scholar
Namaee MR, Li Y, Sui J, Whitcombe T (2018) Comparison of three commonly used equations for calculating local scour depth around bridge pier under ice covered flow condition. World Journal of Engineering and Technology 6(2):50–62Article Google Scholar
Ogunbo JN, Alagbe OA, Oladapo MI, Shin C (2020) N-hidden layer artificial neural network architecture computer code: Geophysical application example. Heliyon 6(6):e04108, DOI: https://doi.org/10.1016/j.heliyon.2020.e04108 Article Google Scholar
Oğuz K, Bor A (2022) Prediction of local scour around bridge piers using hierarchical clustering and adaptive genetic programming. Applied Artificial Intelligence 36(1), DOI: https://doi.org/10.1080/08839514.2021.2001734
Omara H, Abdeelaal GM, Nadaoka K, Tawfik A (2020) Developing empirical formulas for assessing the scour of vertical and inclined piers. Marine Georesources and Geotechnology 38(2):133–143, DOI: https://doi.org/10.1080/1064119X.2018.1559901 Article Google Scholar
Onen F (2014) Prediction of Scour at a Side-Weir with GEP, ANN and Regression Models. Arabian Journal of Science and Engineering 39(8):6031–6041, DOI: https://doi.org/10.1007/s13369-014-1244-y Article Google Scholar
Pal M, Singh NK, Tiwari NK (2011) Support vector regression based modeling of pier scour using field data. Engineering Applications of Artificial Intelligence 24(5):911–916, DOI: https://doi.org/10.1016/j.engappai.2010.11.002 Article Google Scholar
Pandey M, Zakwan M, Khan MA, Bhave S (2020) Development of scour around a circular pier and its modelling using genetic algorithm. Water Supply 20(8):3358–3367, DOI: https://doi.org/10.2166/ws.2020.244 Article Google Scholar
Park CW, Park HI, Cho YK (2017) Evaluation of the applicability of pier local scour formulae using laboratory and field data. Marine Georesources Geotechnology 35(1):1–7, DOI: https://doi.org/10.1080/1064119X.2014.954658 Article Google Scholar
Parola AC, Hagerty DJ, Mueller DS, Melville BW, Parker G, Usher JS (1997) The need for research on scour at bridge crossings, 1997. Proceedings of the 27th IAHR World Congress. San Fransisco, CA, USA
Pizarro A, Manfreda S, Tubaldi E (2020) The science behind scour at bridge foundations: A review. Water 12(2):374, DOI: https://doi.org/10.3390/w12020374 Article Google Scholar
Pizarro A, Samela C, Fiorentino M, Link O, Manfreda S (2017) BRISENT: An entropy-based model for bridge-pier scour estimation under complex hydraulic scenarios. Water 9(11):889, DOI: https://doi.org/10.3390/w9110889 Article Google Scholar
Pregnolato M, Winter AO, Mascarenas D, Sen AD, Bates P, Motley MR (2022) Assessing flooding impact to riverine bridges: An integrated analysis. Natural Hazards and Earth System Sciences 22(5):1559–1576, DOI: https://doi.org/10.5194/nhess-22-1559-2022 Article Google Scholar
Saad NY, Fattouh EM, Mokhtar M (2021) Effect of L-shaped slots on scour around a bridge abutment. Water Practice and Technology 16(3):935–945, DOI: https://doi.org/10.2166/wpt.2021.037 Article Google Scholar
Sarshari E, Mullhaupt P (2015) Application of artificial neural networks in assessing the equilibrium depth of local scour around bridge piers. ASME 2015 34th International Conference on Ocean, Offshore and Arctic Engineering, May 31–June 5, St. John’s, NL, Canada
Sharafati A, Tafarojnoruz A, Yaseen ZM (2020) New stochastic modeling strategy on the prediction enhancement of pier scour depth in cohesive bed materials. Journal of Hydroinformatics 22(3):457–472, DOI: https://doi.org/10.2166/hydro.2020.047 Article Google Scholar
Sheela KG, Deepa SN (2013) Review on methods to fix number of hidden neurons in neural networks. Mathematical Problems in Engineering 2013:425740, DOI: https://doi.org/10.1155/2013/425740 Article Google Scholar
Sreedhara BM, Patil AP, Pushparaj J, Kuntoji G, Naganna SR (2021) Application of gradient tree boosting regressor for the prediction of scour depth around bridge piers. Journal of Hydroinformatics 23(4): 849–863, DOI: https://doi.org/10.2166/hydro.2021.011 Article Google Scholar
Wang C, Yu X, Liang F (2017) Comparison and estimation of the local scour depth around pile groups and wide piers. In Geotechnical Frontiers, American Scciety of Civil Engineers, Reston, VA, USA, 11–19Google Scholar
Wardhana K, Hadipriono FC (2003) Analysis of recent bridge failures in the United States. Journal of Performance of Constricted Facilities 17(3):144–150, DOI: https://doi.org/10.1061/(ASCE)0887-3828(2003)17:3(144)Article Google Scholar
Youssef AM, Abu-Abdullah MM, AlFadail EA, Skilodimou HD, Bathrellos GD (2018) The devastating flood in the arid region a consequence of rainfall and dam failure: Case study. Al-Lith flood on 23th November 2018, Kingdom of Saudi Arabia, Zeitschrift für Geomorphol 63(1):115–136, DOI: https://doi.org/10.1127/zfg/2021/0672 Google Scholar
Zhang B, Zhao H, Tan C, OBrien EJ, Fitzgerald PC, Kim CW (2022) Laboratory investigation on detecting bridge scour using the indirect measurement from a passing vehicle. Remote Sensing 14(13):3106, DOI: https://doi.org/10.3390/rs14133106 Article Google Scholar

Download references

Acknowledgments

Authors also thank “The US Department of the Interior,” US Geol. Surv. Reston, VA, USA” for providing access to scour data. The Researchers would like to thank the Deanship of Graduate Studies and Scientific Research at Qassim University for financial support (QU-APC-2024-9/1).

Author information

Authors and Affiliations

Dept. of Civil Engineering, College of Engineering, Qassim University, Buraydah, 51452, Saudi ArabiaAbdul Razzaq Ghumman, Husnain Haider, Ibrahim Saleh Al Salamah, Md. Shafiquzzaman, Abdullah Alodah & Mohammad Alresheedi
Dept. of Civil Engineering, International Islamic University, Islamabad, 44000, PakistanRashid Farooq
Dept. of Civil Engineering, University of Engineering and Technology, Taxila, 47050, PakistanAfzal Ahmed & Ghufran Ahmed Pasha

DOIhttps://doi.org/10.1007/s12205-024-1161-x

Keywords

An investigation of the effect of the pulse width and amplitude on sand bed scouring by a vertical submerged pulsed jet

수직 수중 펄스 제트에 의한 모래층 정련에 대한 펄스 폭과 진폭의 영향 조사

Chuan Wang ^abc, Hao Yu ^b, Yang Yang ^b, Zhenjun Gao ^c, Bin Xi ^b, Hui Wang ^b, Yulong Yao ^b

^aInternational Shipping Research Institute, GongQing Institute of Science and Technology, Jiujiang, 332020, China^bCollege of Hydraulic Science and Engineering, Yangzhou University, Yangzhou, 225009, China^cCollege of Mechanical and Power Engineering, China Three Gorges University, Yichang, 443002, China

https://doi.org/10.1016/j.oceaneng.2024.117324

Highlights

Numerical simulations and experiments were combined to investigate pulsed jet scour.
The effect mechanism of pulse amplitude on the variation of scour hole depth was analyzed.
Models for the prediction of relative low pulse width with the inlet pulse amplitude have been developed.

Abstract

This paper investigates the effects of the pulse width and amplitude on the scouring of sand beds by vertical submerged pulsed jets using a combination of experimental and numerical calculations. The reliability of the numerical calculations is verified through a comparison between the numerical simulations with the sedimentation scour model and the experimental data at a low pulse width T₂ of 0, with the result that the various errors are within 5%. The results show that the scour hole depth |h_min| grows with the relative low pulse width T₃ throughout three intervals: a slowly increasing zone I, a rapidly increasing zone II, and a decreasing zone III, producing a unique extreme value of |h_min|. The optimal scouring effect equation was obtained by analytically fitting the relationship curve between the pulse amplitude V and the relatively low pulse width T_3. Including the optimal T₃ and optimal duty cycle ƞ. The difference in the scour hole depth |h_min| under different pulse amplitudes is reflected in the initial period F of the jet. With an increasing pulse amplitude, |h_min| goes through three intervals: an increasing zone M, decreasing zone N, and rebound zone R. It is found that the scouring effect in the pulse jet is not necessarily always stronger with a larger amplitude. The results of the research in this paper can provide guidance for optimizing low-frequency pulsed jets for related engineering practices, such as dredging and rock-breaking projects.

Introduction

Submerged jet scouring technology is widely used in marine engineering and dredging projects due to its high efficiency and low cost, and a wide range of research exists on the topic (Zhang et al., 2017; Thaha et al., 2018; Lourenço et al., 2020). Numerous scholars studied the scouring caused by different forms of jets, such as propeller jets (Curulli et al., 2023; Wei et al., 2020), plane jets (Sharafati et al., 2020; Mostaani and Azimi, 2022), free-fall jets (Salmasi and Abraham, 2022; Salmasi et al., 2023), and moving jets (Wang et al., 2021). Among them, vertical jets were more popular than inclined jets due to theirs simple equipment and good silt-scouring performance (Chen et al., 2023; Wang et al., 2017). So, a large number of scholars have proposed relevant static and dynamic empirical equations for the scour depth of submerged jets. Among them, Chen et al. (2022) and Mao et al. (2023) investigated the influence of jet diameters, jet angles, exit velocities, and impinging distances on scouring effects. Finally, based on a large amount of experimental data and theoretical analysis, a semi-empirical equation for the dynamic scour depth in equilibrium was established. Amin et al. (2021) developed semi-empirical prediction equations for asymptotic lengths and empirical equations for the temporal development of lengths. Shakya et al. (2021, 2022) found that the ANN model in dimensionless form performs better than the ANN model in dimensioned form and proposed an equation for predicting the depth of static scour under submerged vertical jets using MNLR. Kartal and Emiroglu (2021) proposed an empirical equation for predicting the maximum dynamic scour depth for a submerged vertical jet with a plate at the nozzle. The effect of soil properties on jet scour has also been studied by numerous scholars. Among them, Nguyen et al. (2017) investigated the effects of compaction dry density and water content on the scour volume, critical shear stress, linear scour coefficient, and volumetric scour coefficient using a new jet-scour test device. Dong et al. (2020) investigated the effect of water content on scour hole size through experiments with a vertical submerged jet scouring a cohesive sediment bed. It was found that the depth and width of the scour holes increased with the increasing water content of the cohesive sediments, and equations for the scour depth and width in the initial stage of scouring and the calculation of the scouring rate were proposed. Kartal and Emiroglu (2023) studied the scouring characteristics of different nozzle types produced in non-cohesive sands. The results of the study found that the air entrainment rate of venturi nozzles was 2–6.5 times higher than that of circular nozzles. Cihan et al. (2022) investigated the effect of different proportions of clay and sand on propeller water jet scouring. And finally, he proposed an estimation equation for the maximum depth and length of the scour hole under equilibrium conditions. From the above summary, it is clear that a great deal of research has been carried out on submerged jet scouring under continuous jet flows.

Pulsed jets have advantages such as higher erosion rates and entrainment rates compared to continuous jets and have therefore received more attention in the development of engineering fields such as cleaning and rock breaking (Raj et al., 2019; Zhu et al., 2019; Kang et al., 2022; Y. Zhang et al., 2023). In the study of jet structure, Li et al. (2018, 2019a, 2019b, 2023) investigated the effects of the jet hole diameter, the number of jet holes, the jet distance, and the tank pressure on pulse jet cleaning. It was found that the transient pressure below the injection hole gradually increased along the airflow direction of the injection pipe, and the peak positive pressure at the inner surface of the injection pipe also increased. Liu and Shen (2019) investigated the effect of a new venturi structure on the performance of pulse jet dust removal. It was found that the longer the length of the venturi or the shorter the throat diameter of the venturi, the greater the energy loss. Zhang et al. (2023b) studied jet scouring at different angles based on FLOW-3D. It was found that counter flow scouring is better than down flow scouring. In the study of pulsed structure, Li et al. (2020) investigated the effects of different pulse amplitudes, pulse frequencies, and circumferential pressures on the rock-breaking performance. It was found that the rock-breaking performance of the jet increased with increasing pulse amplitude. However, due to the variation in pulse frequency, the rock-breaking performance does not show a clear pattern. The effect of Reynolds number on pulsating jets impinging on a plane was systematically investigated by H. H Medina et al. (2013) It was found that pulsation leads to a shorter core region of the jet, a faster decrease in the centerline axial velocity component, and a wider axial velocity distribution. Bi and Zhu (2021) investigated the effect of nozzle geometry on jet performance at low Reynolds numbers, while Luo et al. (2020) studied pulse jet propulsion at high Reynolds numbers and finally found that higher Reynolds numbers accelerate the formation of irregular vortices and symmetry-breaking instabilities. Cao et al. (2019) investigated the effect of four different pulse flushing methods on diamond core drilling efficiency. It was found that the use of intermittent rinsing methods not only increases penetration rates but also reduces rinse fluid flow and saves power.

Previous research on vertical submerged jet scouring has primarily focused on the effect of jet structure on scouring under continuous jet conditions. However, there have been fewer studies conducted on scouring under pulsed jet conditions. We found that the pulsed jet has a high erosion rate and entrainment rate, which can significantly enhance the scouring effect of the jet. Therefore, to address the research gap, this paper utilizes a combination of numerical calculations and experiments to investigate the effects of high pulse width, low pulse width, and amplitude on the scouring of vertically submerged jets. The study includes analyzing the structure of the pulsed jet flow field, studying the evolution of the scouring effect over time, and examining the relationship between the optimal pulse width, duty cycle, and amplitude. The study’s conclusions of the study can provide a reference for optimizing the performance of pulse jets in the fields of jet scouring applications, such as dredger dredging and pulse rock breaking, as well as a theoretical basis for the development of submerged pulse jets.

Section snippets

Model and calculation settings

Fig. 1 shows the geometric model of the submerged vertical jet impinging on the sand bed, which was built in Flow-3D on a 1:1 dimensional scale corresponding to the experiment. The jet scour simulation was set up between four baffles, where the top baffle was used to ensure that the jet entered only from the brass tube, and the remaining three tank baffles were used to fix the sediment and water body. The computational domain consisted of only solid and liquid components, with the specific

The effects of the pulse width on submerged jet scouring

The blocking pulsed jet, indicated as A and C in Fig. 8(a)–is discontinuous and divided into a water section and a pulse interval section. The water section in region A is not a regular shape, due to part of the water section near the side wall being affected by the wall friction and the falling speed being lower, but this also shows that the wall plays a certain buffer role. Region B of Fig. 8(a) shows the symmetrical vortex generation that occurs below the nozzle as the water section is

conclusions

In this paper, the effects of the pulse width and pulse amplitude on jet scour under submerged low-frequency pulse conditions are discussed and investigated, and the following conclusions have been reached.

(1)The errors of between the Flow-3D simulation and the experimental measurements were within 5%, which proves that the sedimentation scouring model of Flow-3D can reliably perform numerical calculation of the type considered in this paper.
(2)The change in the high pulse width T₁ in the pulse cycle

CRediT authorship contribution statement

Chuan Wang: Data curation, Conceptualization. Hao Yu: Writing – original draft. Yang Yang: Writing – review & editing, Supervision. Zhenjun Gao: Supervision, Writing – review & editing. Bin Xi: Resources, Project administration. Hui Wang: Software, Data curation. Yulong Yao: Validation, Software.

Declaration of competing interest

The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper.

References (44)

X. Bi et al.Effect of nozzle geometry on the performance of pulsed-jet propulsion at low Reynolds numberJ. Fluid Struct.(2021)
J. Chen et al.Experimental investigation of scour of sand beds by submerged circular vertical turbulent jetsOcean Eng.(2022)
K. Cihan et al.Unconfined propeller jet scour on clay/sand mixturesOcean Eng.(2022)
G. Curulli et al.Improved formulation for the geometric characteristics of the scour hole and deposition mound caused by a rotating propeller jet on a mobile bedOcean Eng.(2023)
C. Dong et al.Scouring by submerged steady water jet vertically impinging on a cohesive bedOcean Eng.(2020)
V. Kartal et al.Effect of nozzle type on local scour in water jets: an experimental studyOcean Eng.(2023)
S. Li et al.Influence of injection pipe characteristics on pulse-jet cleaning uniformity in a pleated cartridge filterPowder Technol.(2018)
S. Li et al.Experimental investigation of the optimization of nozzles under an injection pipe in a pulse-jet cartridge filterPowder Technol.(2019)
S. Li et al.Effects of cleaning mode on the performances of pulse-jet cartridge filter under varying particle sizesAdv. Powder Technol.(2019)
H. Li et al.Numerical simulation of rock-breaking under the impact load of self-excited oscillating pulsed waterjetTunn. Undergr. Space Technol.(2020)
J. Mao et al.Experimental investigation on sand bed scour by an oblique planar water jet at varying impinging anglesOcean Eng.(2023)
A. Mostaani et al.Analytical approach for predicting local scour downstream of submerged sluice gate with an apronInt. J. Sediment Res.(2022)
P. Raj et al.Investigation of sandstone erosion by continuous and pulsed water jetsJ. Manuf. Process.(2019)
F. Salmasi et al.Experimental investigation and prediction of free fall jet scouring using machine learning modelsInt. J. Sediment Res.(2023)
A. Sharafati et al.Simulation of the depth scouring downstream sluice gate: the validation of newly developed data-intelligent modelsJ Hydro-Environ Res.(2020)
C. Wang et al.Experimental investigation on impingement of a submerged circular water jet at varying impinging angles and Reynolds numbersExp. Therm. Fluid Sci.(2017)
B. Wang et al.Modeling the hydraulic excavation of cohesive soil by a moving vertical jetOcean Eng.(2021)
M.R. Amin et al.Scouring of sand beds by short impinging turbulent jetsProc. Inst. Civ. Eng. Water Manage.(2021)
M.R. BarkhudarovLagrangian VOF Advection method for FLOW-3DFlow Science Inc(2004)
X. Cao et al.Diamond core drilling process using intermittent flushing modeArabian J. Geosci.(2019)
J. Chen et al.Experimental investigation on flow characteristics of vertical and oblique circular impinging jetPhys. Fluids(2023)
D.A. ChinWater-resources Engineering(2006)

Estimating maximum initial wave amplitude of subaerial landslide tsunamis: A three-dimensional modelling approach

해저 산사태 쓰나미의 최대 초기 파동 진폭 추정: 3차원 모델링 접근법

Ramtin Sabeti ^a, Mohammad Heidarzadeh ^ab

^aDepartment of Architecture and Civil Engineering, University of Bath, Bath BA27AY, UK
^bHydroCoast Consulting Engineers Ltd, Bath, UK

https://doi.org/10.1016/j.ocemod.2024.102360

Highlights

•Landslide travel distance is considered for the first time in a predictive equation.
•Predictive equation derived from databases using 3D physical and numerical modeling.
•The equation was successfully tested on the 2018 Anak Krakatau tsunami event.
•The developed equation using three-dimensional data exhibits a 91 % fitting quality.

Abstract

Landslide tsunamis, responsible for thousands of deaths and significant damage in recent years, necessitate the allocation of sufficient time and resources for studying these extreme natural hazards. This study offers a step change in the field by conducting a large number of three-dimensional numerical experiments, validated by physical tests, to develop a predictive equation for the maximum initial amplitude of tsunamis generated by subaerial landslides. We first conducted a few 3D physical experiments in a wave basin which were then applied for the validation of a 3D numerical model based on the Flow3D-HYDRO package. Consequently, we delivered 100 simulations using the validated model by varying parameters such as landslide volume, water depth, slope angle and travel distance. This large database was subsequently employed to develop a predictive equation for the maximum initial tsunami amplitude. For the first time, we considered travel distance as an independent parameter for developing the predictive equation, which can significantly improve the predication accuracy. The predictive equation was tested for the case of the 2018 Anak Krakatau subaerial landslide tsunami and produced satisfactory results.

Keywords

Tsunami, Subaerial landslide, Physical modelling, Numerical simulation, FLOW-3D HYDRO

1. Introduction and literature review

The Anak Krakatau landslide tsunami on 22nd December 2018 was a stark reminder of the dangers posed by subaerial landslide tsunamis (Ren et al., 2020; Mulia et al. 2020a; Borrero et al., 2020; Heidarzadeh et al., 2020; Grilli et al., 2021). The collapse of the volcano’s southwest side into the ocean triggered a tsunami that struck the Sunda Strait, leading to approximately 450 fatalities (Syamsidik et al., 2020; Mulia et al., 2020b) (Fig. 1). As shown in Fig. 1, landslide tsunamis (both submarine and subaerial) have been responsible for thousands of deaths and significant damage to coastal communities worldwide. These incidents underscored the critical need for advanced research into landslide-generated waves to aid in hazard prediction and mitigation. This is further emphasized by recent events such as the 28th of November 2020 landslide tsunami in the southern coast mountains of British Columbia (Canada), where an 18 million m³ rockslide generated a massive tsunami, with over 100 m wave run-up, causing significant environmental and infrastructural damage (Geertsema et al., 2022).

Physical modelling and numerical simulation are crucial tools in the study of landslide-induced waves due to their ability to replicate and analyse the complex dynamics of landslide events (Kim et al., 2020). In two-dimensional (2D) modelling, the discrepancy between dimensions can lead to an artificial overestimation of wave amplification (e.g., Heller and Spinneken, 2015). This limitation is overcome with 3D modelling, which enables the scaled-down representation of landslide-generated waves while avoiding the simplifications inherent in 2D approaches (Erosi et al., 2019). Another advantage of 3D modelling in studying landslide-generated waves is its ability to accurately depict the complex dynamics of wave propagation, including lateral and radial spreading from the slide impact zone, a feature unattainable with 2D models (Heller and Spinneken, 2015).

Physical experiments in tsunami research, as presented by authors such as Romano et al. (2020), McFall and Fritz (2016), and Heller and Spinneken (2015), have supported 3D modelling works through validation and calibration of the numerical models to capture the complexities of wave generation and propagation. Numerical modelling has increasingly complemented experimental approach in tsunami research due to the latter’s time and resource-intensive nature, particularly for 3D models (Li et al., 2019; Kim et al., 2021). Various numerical approaches have been employed, from Eulerian and Lagrangian frameworks to depth-averaged and Navier–Stokes models, enhancing our understanding of tsunami dynamics (Si et al., 2018; Grilli et al., 2019; Heidarzadeh et al., 2017, 2020; Iorio et al., 2021; Zhang et al., 2021; Kirby et al., 2022; Wang et al., 2021, 2022; Hu et al., 2022). The sophisticated numerical techniques, including the Particle Finite Element Method and the Immersed Boundary Method, have also shown promising results in modelling highly dynamic landslide scenarios (Mulligan et al., 2020; Chen et al., 2020). Among these methods and techniques, FLOW-3D HYDRO stands out in simulating landslide-generated tsunami waves due to its sophisticated technical features such as offering Tru Volume of Fluid (VOF) method for precise free surface tracking (e.g., Sabeti and Heidarzadeh 2022a). TruVOF distinguishes itself through a split Lagrangian approach, adeptly reducing cumulative volume errors in wave simulations by dynamically updating cell volume fractions and areas with each time step. Its intelligent adaptation of time step size ensures precise capture of evolving free surfaces, offering unparalleled accuracy in modelling complex fluid interfaces and behaviour (Flow Science, 2023).

Predictive equations play a crucial role in assessing the potential hazards associated with landslide-generated tsunami waves due to their ability to provide risk assessment and warnings. These equations can offer swift and reasonable evaluations of potential tsunami impacts in the absence of detailed numerical simulations, which can be time-consuming and expensive to produce. Among multiple factors and parameters within a landslide tsunami generation, the initial maximum wave amplitude (Fig. 1) stands out due to its critical role. While it is most likely that the initial wave generated by a landslide will have the highest amplitude, it is crucial to clarify that the term “initial maximum wave amplitude” refers to the highest amplitude within the first set of impulse waves. This parameter is essential in determining the tsunami’s impact severity, with higher amplitudes signalling a greater destructive potential (Sabeti and Heidarzadeh 2022a). Additionally, it plays a significant role in tsunami modelling, aiding in the prediction of wave propagation and the assessment of potential impacts.

In this study, we initially validate the FLOW-3D HYDRO model through a series of physical experiments conducted in a 3D wave tank at University of Bath (UK). Upon confirmation of the model’s accuracy, we use it to systematically vary parameters namely landslide volume, water depth, slope angle, and travel distance, creating an extensive database. Alongside this, we perform a sensitivity analysis on these variables to discern their impacts on the initial maximum wave amplitude. The generated database was consequently applied to derive a non-dimensional predictive equation aimed at estimating the initial maximum wave amplitude in real-world landslide tsunami events.

Two innovations of this study are: (i) The predictive equation of this study is based on a large number of 3D experiments whereas most of the previous equations were based on 2D results, and (ii) For the first time, the travel distance is included in the predictive equation as an independent parameter. To evaluate the performance of our predictive equation, we applied it to a previous real-world subaerial landslide tsunami, i.e., the Anak Krakatau 2018 event. Furthermore, we compare the performance of our predictive equation with other existing equations.

2. Data and methods

The methodology applied in this research is a combination of physical and numerical modelling. Limited physical modelling was performed in a 3D wave basin at the University of Bath (UK) to provide data for calibration and validation of the numerical model. After calibration and validation, the numerical model was employed to model a large number of landslide tsunami scenarios which allowed us to develop a database for deriving a predictive equation.

2.1. Physical experiments

To validate our numerical model, we conducted a series of physical experiments including two sets in a 3D wave basin at University of Bath, measuring 2.50 m in length (W_L), 2.60 m in width (W_W), and 0.60 m in height (W_H) (Fig. 2a). Conducting two distinct sets of experiments (Table 1), each with different setups (travel distance, location, and water depth), provided a robust framework for validation of the numerical model. For wave measurement, we employed a twin wire wave gauge from HR Wallingford (https://equipit.hrwallingford.com). In these experiments, we used a concrete prism solid block, the dimensions of which are outlined in Table 2. In our experiments, we employed a concrete prism solid block with a density of 2600 kg/m³, chosen for its similarity to the natural density of landslides, akin to those observed with the 2018 Anak Krakatau tsunami, where the landslide composition is predominantly solid rather than granular. The block’s form has also been endorsed in prior studies (Watts, 1998; Najafi-Jilani and Ataie-Ashtiani, 2008) as a suitable surrogate for modelling landslide-induced waves. A key aspect of our methodology was addressing scale effects, following the guidelines proposed by Heller et al. (2008) as it is described in Table 1. To enhance the reliability and accuracy of our experimental data, we conducted each physical experiment three times which revealed all three experimental waveforms were identical. This repetition was aimed at minimizing potential errors and inconsistencies in laboratory measurements.

Table 1. The locations and other information of the laboratory setups for making landslide-generated waves in the physical wave basin. This table details the specific parameters for each setup, including slope range (α), slide volume (V), kinematic viscosity (ν), water depth (h), travel distance (D), surface tension coefficient of water (σ), Reynolds number (R), Weber number (W), and the precise coordinates of the wave gauges (WG).

Lab	α(°)	V (m³)	h (m)	D (m)		(ν) (m²/s)	(σ) (N/m)	Acceptable range for avoiding scale effects*	Observed values of W and R ^⁎⁎
Lab 1	45	2.60 × 10⁻³	0.247	0.070	X₁=1.090 m	1.01 × 10⁻⁶	0.073	R > 3.0 × 10⁵	R₁ = 3.80 × 10⁵
					Y₁=1.210 m				R₁ = 3.80 × 10⁵
					Y₁=1.210 m				W₁ = 8.19 × 10⁵
					Z₁=0.050m			W >5.0 × 10³	W₁ = 8.19 × 10⁵
Lab 2	45	2.60 × 10⁻³	0.246	0.045	X₂=1.030 m	1.01 × 10⁻⁶	0.073		R₂ = 3.78 × 10⁵
					Y₂=1.210 m				W₂ = 8.13 × 10⁵
					Z₂=0.050 m				W₂ = 8.13 × 10⁵

⁎

The acceptable ranges for avoiding scale effects are based on the study by Heller et al. (2008).⁎⁎

The Reynolds number (R) is given by g^0.5h^1.5/ν, with ν denoting the kinematic viscosity. The Weber number (W) is W = ρgh²/σ, where σ represents surface tension coefficient and ρ = 1000kg/m³ is the density of water. In our experiments, conducted at a water temperature of approximately 20 °C, the kinematic viscosity (ν) and the surface tension coefficient of water (σ) are 1.01 × 10⁻⁶ m²/s and 0.073 N/m, respectively (Kestin et al., 1978).

Table 2. Specifications of the solid block used in physical experiments for generating subaerial landslides in the laboratory.

Solid-block attributes	Property metrics	Geometric shape
Slide width (b_s)	0.26 m
Slide length (l_s)	0.20 m
Slide thickness (s)	0.10 m
Slide volume (V)	2.60 × 10⁻³ m³
Specific gravity, (γ_s)	2.60
Slide weight (m_s)	6.86 kg

2.2. Numerical simulations applying FLOW-3D hydro

The detailed theoretical framework encompassing the governing equations, the computational methodologies employed, and the specific techniques used for tracking the water surface in these simulations are thoroughly detailed in the study by Sabeti et al. (2024). Here, we briefly explain some of the numerical details. We defined a uniform mesh for our flow domain, carefully crafted with a fine spatial resolution of 0.005 m (i.e., grid size). The dimensions of the numerical model directly matched those of our wave basin used in the physical experiment, being 2.60 m wide, 0.60 m deep, and 2.50 m long (Fig. 2). This design ensures comprehensive coverage of the study area. The output intervals of the numerical model are set at 0.02 s. This timing is consistent with the sampling rates of wave gauges used in laboratory settings. The friction coefficient in the FLOW-3D HYDRO is designated as 0.45. This value corresponds to the Coulombic friction measurements obtained in the laboratory, ensuring that the simulation accurately reflects real-world physical interactions.

In order to simulate the landslide motion, we applied coupled motion objects in FLOW-3D-HYDRO where the dynamics are predominantly driven by gravity and surface friction. This methodology stands in contrast to other models that necessitate explicit inputs of force and torque. This approach ensures that the simulation more accurately reflects the natural movement of landslides, which is heavily reliant on gravitational force and the interaction between sliding surfaces. The stability of the numerical simulations is governed by the Courant Number criterion (Courant et al., 1928), which dictates the maximum time step (Δt) for a given mesh size (Δx) and flow speed (U). According to Courant et al. (1928), this number is required to stay below one to ensure stability of numerical simulations. In our simulations, the Courant number is always maintained below one.

In alignment with the parameters of physical experiments, we set the fluid within the mesh to water, characterized by a density of 1000 kg/m³ at a temperature of 20 °C. Furthermore, we defined the top, front, and back surfaces of the mesh as symmetry planes. The remaining surfaces are designated as wall types, incorporating no-slip conditions to accurately simulate the interaction between the fluid and the boundaries. In terms of selection of an appropriate turbulence model, we selected the k–ω model that showed a better performance than other turbulence methods (e.g., Renormalization-Group) in a previous study (Sabeti et al., 2024). The simulations are conducted using a PC Intel® Core™ i7-10510U CPU with a frequency of 1.80 GHz, and a 16 GB RAM. On this PC, completion of a 3-s simulation required approximately 12.5 h.

2.3. Validation

The FLOW-3D HYDRO numerical model was validated using the two physical experiments (Fig. 3) outlined in Table 1. The level of agreement between observations (O_i) and simulations (S_i) is examined using the following equation:(1)�=|��−��|×100where ε represents the mismatch error, O_i denotes the observed laboratory values, and S_i represents the simulated values from the FLOW-3D HYDRO model. The results of this validation process revealed that our model could replicate the waves generated in the physical experiments with a reasonable degree of mismatch (ε): 14 % for Lab 1 and 8 % for Lab 2 experiments, respectively (Fig. 3). These values indicate that while the model is not perfect, it provides a sufficiently close approximation of the real-world phenomena.

In terms of mesh efficiency, we varied the mesh size to study sensitivity of the numerical results to mesh size. First, by halving the mesh size and then by doubling it, we repeated the modelling by keeping other parameters unchanged. This analysis guided that a mesh size of ∆x = 0.005 m is the most effective for the setup of this study. The total number of computational cells applying mesh size of 0.005 m is 9.269 × 10⁶.

2.4. The dataset

The validated numerical model was employed to conduct 100 simulations, incorporating variations in four key landslide parameters namely water depth, slope angle, slide volume, and travel distance. This methodical approach was essential for a thorough sensitivity analysis of these variables, and for the creation of a detailed database to develop a predictive equation for maximum initial tsunami amplitude. Within the model, 15 distinct slide volumes were established, ranging from 0.10 × 10⁻³ m³ to 6.25 × 10⁻³ m³ (Table 3). The slope angle varied between 35° and 55°, and water depth ranged from 0.24 m to 0.27 m. The travel distance of the landslides was varied, spanning from 0.04 m to 0.07 m. Detailed configurations of each simulation, along with the maximum initial wave amplitudes and dominant wave periods are provided in Table 4.

Table 3. Geometrical information of the 15 solid blocks used in numerical modelling for generating landslide tsunamis. Parameters are: l_s, slide length; b_s, slide width; s, slide thickness; γ_s, specific gravity; and V, slide volume.

Solid block	l_s (m)	b_s (m)	s (m)	V (m³)	γ_s
Block-1	0.310	0.260	0.155	6.25 × 10⁻³	2.60
Block-2	0.300	0.260	0.150	5.85 × 10⁻³	2.60
Block-3	0.280	0.260	0.140	5.10 × 10⁻³	2.60
Block-4	0.260	0.260	0.130	4.39 × 10⁻³	2.60
Block-5	0.240	0.260	0.120	3.74 × 10⁻³	2.60
Block-6	0.220	0.260	0.110	3.15 × 10⁻³	2.60
Block-7	0.200	0.260	0.100	2.60 × 10⁻³	2.60
Block-8	0.180	0.260	0.090	2.11 × 10⁻³	2.60
Block-9	0.160	0.260	0.080	1.66 × 10⁻³	2.60
Block-10	0.140	0.260	0.070	1.27 × 10⁻³	2.60
Block-11	0.120	0.260	0.060	0.93 × 10⁻³	2.60
Block-12	0.100	0.260	0.050	0.65 × 10⁻³	2.60
Block-13	0.080	0.260	0.040	0.41 × 10⁻³	2.60
Block-14	0.060	0.260	0.030	0.23 × 10⁻³	2.60
Block-15	0.040	0.260	0.020	0.10 × 10⁻³	2.60

Table 4. The numerical simulation for the 100 tests performed in this study for subaerial solid-block landslide-generated waves. Parameters are a_M, maximum wave amplitude; α, slope angle; h, water depth; D, travel distance; and T, dominant wave period. The location of the wave gauge is X=1.030 m, Y=1.210 m, and Z=0.050 m. The properties of various solid blocks are presented in Table 3.

Test-	Block No	α (°)	h (m)	D (m)	T(s)	a_M (m)
1	Block-7	45	0.246	0.029	0.510	0.0153
2	Block-7	45	0.246	0.030	0.505	0.0154
3	Block-7	45	0.246	0.031	0.505	0.0156
4	Block-7	45	0.246	0.032	0.505	0.0158
5	Block-7	45	0.246	0.033	0.505	0.0159
6	Block-7	45	0.246	0.034	0.505	0.0160
7	Block-7	45	0.246	0.035	0.505	0.0162
8	Block-7	45	0.246	0.036	0.505	0.0166
9	Block-7	45	0.246	0.037	0.505	0.0167
10	Block-7	45	0.246	0.038	0.505	0.0172
11	Block-7	45	0.246	0.039	0.505	0.0178
12	Block-7	45	0.246	0.040	0.505	0.0179
13	Block-7	45	0.246	0.041	0.505	0.0181
14	Block-7	45	0.246	0.042	0.505	0.0183
15	Block-7	45	0.246	0.043	0.505	0.0190
16	Block-7	45	0.246	0.044	0.505	0.0197
17	Block-7	45	0.246	0.045	0.505	0.0199
18	Block-7	45	0.246	0.046	0.505	0.0201
19	Block-7	45	0.246	0.047	0.505	0.0191
20	Block-7	45	0.246	0.048	0.505	0.0217
21	Block-7	45	0.246	0.049	0.505	0.0220
22	Block-7	45	0.246	0.050	0.505	0.0226
23	Block-7	45	0.246	0.051	0.505	0.0236
24	Block-7	45	0.246	0.052	0.505	0.0239
25	Block-7	45	0.246	0.053	0.510	0.0240
26	Block-7	45	0.246	0.054	0.505	0.0241
27	Block-7	45	0.246	0.055	0.505	0.0246
28	Block-7	45	0.246	0.056	0.505	0.0247
29	Block-7	45	0.246	0.057	0.505	0.0248
30	Block-7	45	0.246	0.058	0.505	0.0249
31	Block-7	45	0.246	0.059	0.505	0.0251
32	Block-7	45	0.246	0.060	0.505	0.0257
33	Block-1	45	0.246	0.045	0.505	0.0319
34	Block-2	45	0.246	0.045	0.505	0.0294
35	Block-3	45	0.246	0.045	0.505	0.0282
36	Block-4	45	0.246	0.045	0.505	0.0262
37	Block-5	45	0.246	0.045	0.505	0.0243
38	Block-6	45	0.246	0.045	0.505	0.0223
39	Block-7	45	0.246	0.045	0.505	0.0196
40	Block-8	45	0.246	0.045	0.505	0.0197
41	Block-9	45	0.246	0.045	0.505	0.0198
42	Block-10	45	0.246	0.045	0.505	0.0184
43	Block-11	45	0.246	0.045	0.505	0.0173
44	Block-12	45	0.246	0.045	0.505	0.0165
45	Block-13	45	0.246	0.045	0.404	0.0153
46	Block-14	45	0.246	0.045	0.404	0.0124
47	Block-15	45	0.246	0.045	0.505	0.0066
48	Block-7	45	0.202	0.045	0.404	0.0220
49	Block-7	45	0.204	0.045	0.404	0.0219
50	Block-7	45	0.206	0.045	0.404	0.0218
51	Block-7	45	0.208	0.045	0.404	0.0217
52	Block-7	45	0.210	0.045	0.404	0.0216
53	Block-7	45	0.212	0.045	0.404	0.0215
54	Block-7	45	0.214	0.045	0.505	0.0214
55	Block-7	45	0.216	0.045	0.505	0.0214
56	Block-7	45	0.218	0.045	0.505	0.0213
57	Block-7	45	0.220	0.045	0.505	0.0212
58	Block-7	45	0.222	0.045	0.505	0.0211
59	Block-7	45	0.224	0.045	0.505	0.0208
60	Block-7	45	0.226	0.045	0.505	0.0203
61	Block-7	45	0.228	0.045	0.505	0.0202
62	Block-7	45	0.230	0.045	0.505	0.0201
63	Block-7	45	0.232	0.045	0.505	0.0201
64	Block-7	45	0.234	0.045	0.505	0.0200
65	Block-7	45	0.236	0.045	0.505	0.0199
66	Block-7	45	0.238	0.045	0.404	0.0196
67	Block-7	45	0.240	0.045	0.404	0.0194
68	Block-7	45	0.242	0.045	0.404	0.0193
69	Block-7	45	0.244	0.045	0.404	0.0192
70	Block-7	45	0.246	0.045	0.505	0.0190
71	Block-7	45	0.248	0.045	0.505	0.0189
72	Block-7	45	0.250	0.045	0.505	0.0187
73	Block-7	45	0.252	0.045	0.505	0.0187
74	Block-7	45	0.254	0.045	0.505	0.0186
75	Block-7	45	0.256	0.045	0.505	0.0184
76	Block-7	45	0.258	0.045	0.505	0.0182
77	Block-7	45	0.259	0.045	0.505	0.0183
78	Block-7	45	0.260	0.045	0.505	0.0191
79	Block-7	45	0.261	0.045	0.505	0.0192
80	Block-7	45	0.262	0.045	0.505	0.0194
81	Block-7	45	0.263	0.045	0.505	0.0195
82	Block-7	45	0.264	0.045	0.505	0.0195
83	Block-7	45	0.265	0.045	0.505	0.0197
84	Block-7	45	0.266	0.045	0.505	0.0197
85	Block-7	45	0.267	0.045	0.505	0.0198
86	Block-7	45	0.270	0.045	0.505	0.0199
87	Block-7	30	0.246	0.045	0.505	0.0101
88	Block-7	35	0.246	0.045	0.505	0.0107
89	Block-7	36	0.246	0.045	0.505	0.0111
90	Block-7	37	0.246	0.045	0.505	0.0116
91	Block-7	38	0.246	0.045	0.505	0.0117
92	Block-7	39	0.246	0.045	0.505	0.0119
93	Block-7	40	0.246	0.045	0.505	0.0121
94	Block-7	41	0.246	0.045	0.505	0.0127
95	Block-7	42	0.246	0.045	0.404	0.0154
96	Block-7	43	0.246	0.045	0.404	0.0157
97	Block-7	44	0.246	0.045	0.404	0.0162
98	Block-7	45	0.246	0.045	0.505	0.0197
99	Block-7	50	0.246	0.045	0.505	0.0221
100	Block-7	55	0.246	0.045	0.505	0.0233

In all these 100 simulations, the wave gauge was consistently positioned at coordinates X=1.09 m, Y=1.21 m, and Z=0.05 m. The dominant wave period for each simulation was determined using the Fast Fourier Transform (FFT) function in MATLAB (MathWorks, 2023). Furthermore, the classification of wave types was carried out using a wave categorization graph according to Sorensen (2010), as shown in Fig. 4a. The results indicate that the majority of the simulated waves are on the border between intermediate and deep-water waves, and they are categorized as Stokes waves (Fig. 4a). Four sample waveforms from our 100 numerical experiments are provided in Fig. 4b.

The dataset in Table 4 was used to derive a new predictive equation that incorporates travel distance for the first time to estimate the initial maximum tsunami amplitude. In developing this equation, a genetic algorithm optimization technique was implemented using MATLAB (MathWorks 2023). This advanced approach entailed the use of genetic algorithms (GAs), an evolutionary algorithm type inspired by natural selection processes (MathWorks, 2023). This technique is iterative, involving selection, crossover, and mutation processes to evolve solutions over several generations. The goal was to identify the optimal coefficients and powers for each landslide parameter in the predictive equation, ensuring a robust and reliable model for estimating maximum wave amplitudes. Genetic Algorithms excel at optimizing complex models by navigating through extensive combinations of coefficients and exponents. GAs effectively identify highly suitable solutions for the non-linear and complex relationships between inputs (e.g., slide volume, slope angle, travel distance, water depth) and the output (i.e., maximum initial wave amplitude, a_M). MATLAB’s computational environment enhances this process, providing robust tools for GA to adapt and evolve solutions iteratively, ensuring the precision of the predictive model (Onnen et al., 1997). This approach leverages MATLAB’s capabilities to fine-tune parameters dynamically, achieving an optimal equation that accurately estimates a_M. It is important to highlight that the nondimensionalized version of this dataset is employed to develop a predictive equation which enables the equation to reproduce the maximum initial wave amplitude (a_M) for various subaerial landslide cases, independent of their dimensional differences (e.g., Heler and Hager 2014; Heller and Spinneken 2015; Sabeti and Heidarzadeh 2022b). For this nondimensionalization, we employed the water depth (h) to nondimensionalize the slide volume (V/h³) and travel distance (D/h). The slide thickness (s) was applied to nondimensionalize the water depth (h/s).

2.5. Landslide velocity

In discussing the critical role of landslide velocity for simulating landslide-generated waves, we focus on the mechanisms of landslide motion and the techniques used to record landslide velocity in our simulations (Fig. 5). Also, we examine how these methods were applied in two distinct scenarios: Lab 1 and Lab 2 (see Table 1 for their details). Regarding the process of landslide movement, a slide starts from a stationary state, gaining momentum under the influence of gravity and this acceleration continues until the landslide collides with water, leading to a significant reduction in its speed before eventually coming to a stop (Fig. 5) (e.g., Panizzo et al. 2005).

To measure the landslide’s velocity in our simulations, we attached a probe at the centre of the slide, which supplied a time series of the velocity data. The slide’s velocity (v_s) peaks at the moment it enters the water (Fig. 5), a point referred to as the impact time (t_Imp). Following this initial impact, the slides continue their underwater movement, eventually coming to a complete halt (t_Stop). Given the results in Fig. 5, it can be seen that Lab 1, with its longer travel distance (0.070 m), exhibits a higher peak velocity of 1.89 m/s. This increase in velocity is attributed to the extended travel distance allowing more time for the slide to accelerate under gravity. Whereas Lab 2, featuring a shorter travel distance (0.045 m), records a lower peak velocity of 1.78 m/s. This difference underscores how travel distance significantly influences the dynamics of landslide motion. After reaching the peak, both profiles show a sharp decrease in velocity, marking the transition to submarine motion until the slides come to a complete stop (t_Stop). There are noticeable differences observable in Fig. 5 between the Lab-1 and Lab-2 simulations, including the peaks at 0.3 s . These variations might stem from the placement of the wave gauge, which differs slightly in each scenario, as well as the water depth’s minor discrepancies and, the travel distance.

2.6. Effect of air entrainment

In this section we examine whether it is required to consider air entrainment for our modelling or not as the FLOW-3D HYDRO package is capable of modelling air entrainment. The process of air entrainment in water during a landslide tsunami and its subsequent transport involve two key components: the quantification of air entrainment at the water surface, and the simulation of the air’s transport within the fluid (Hirt, 2003). FLOW-3D HYDRO employs the air entrainment model to compute the volume of air entrained at the water’s surface utilizing three approaches: a constant density model, a variable density model accounting for bulking, and a buoyancy model that adds the Drift-FLUX mechanism to variable density conditions (Flow Science, 2023). The calculation of the entrainment rate is based on the following equation:(2)��=��[2(��−��−2�/��)]1/2where parameters are: V_air, volume of air; C_air, entrainment rate coefficient; A_s, surface area of fluid; ρ, fluid density; k, turbulent kinetic energy; g_n, gravity normal to surface; L_t, turbulent length scale; and σ, surface tension coefficient. The value of k is directly computed from the Reynolds-averaged Navier-Stokes (RANS) (k–w) calculations in our model.

In this study, we selected the variable density + Drift-FLUX model, which effectively captures the dynamics of phase separation and automatically activates the constant density and variable density models. This method simplifies the air-water mixture, treating it as a single, homogeneous fluid within each computational cell. For the phase volume fractions f₁and f₂, the velocities are expressed in terms of the mixture and relative velocities, denoted as u and u_r, respectively, as follows:(3)��1��+�.(�1�)=��1��+�.(�1�)−�.(�1�2��)=0(4)��2��+�.(�2�)=��2��+�.(�2�)−�.(�1�2��)=0

The outcomes from this simulation are displayed in Fig. 6, which indicates that the influence of air entrainment on the generated wave amplitude is approximately 2 %. A value of 0.02 for the entrained air volume fraction means that, in the simulated fluid, approximately 2 % of the volume is composed of entrained air. In other words, for every unit volume of the fluid-air mixture at that location, 2 % is air and the remaining 98 % is water. The configuration of Test-17 (Table 4) was employed for this simulation. While the effect of air entrainment is anticipated to be more significant in models of granular landslide-generated waves (Fritz, 2002), in our simulations we opted not to incorporate this module due to its negligible impact on the results.

3. Results

In this section, we begin by presenting a sequence of our 3D simulations capturing different time steps to illustrate the generation process of landslide-generated waves. Subsequently, we derive a new predictive equation to estimate the maximum initial wave amplitude of landslide-generated waves and assess its performance.

3.1. Wave generation and propagation

To demonstrate the wave generation process in our simulation, we reference Test-17 from Table 4, where we employed Block-7 (Tables 3, 4). In this configuration, the slope angle was set to 45°, with a water depth of 0.246 m and a travel distance at 0.045 m (Fig. 7). At 0.220 s, the initial impact of the moving slide on the water is depicted, marking the onset of the wave generation process (Fig. 7a). Disturbances are localized to the immediate area of impact, with the rest of the water surface remaining undisturbed. At this time, a maximum water particle velocity of 1.0 m/s – 1.2 m/s is seen around the impact zone (Fig. 7d). Moving to 0.320 s, the development of the wave becomes apparent as energy transfer from the landslide to the water creates outwardly radiating waves with maximum water particle velocity of up to around 1.6 m/s – 1.8 m/s (Fig. 7b, e). By the time 0.670 s, the wave has fully developed and is propagating away from the impact point exhibiting maximum water particle velocity of up to 2.0 m/s – 2.1 m/s. Concentric wave fronts are visible, moving outwards in all directions, with a colour gradient signifying the highest wave amplitude near the point of landslide entry, diminishing with distance (Fig. 7c, f).

3.2. Influence of landslide parameters on tsunami amplitude

In this section, we investigate the effects of various landslide parameters namely slide volume (V), water depth (h), slipe angle (α) and travel distance (D) on the maximum initial wave amplitude (a_M). Fig. 8 presents the outcome of these analyses. According to Fig. 8, the slide volume, slope angle, and travel distance exhibit a direct relationship with the wave amplitude, meaning that as these parameters increase, so does the amplitude. Conversely, water depth is inversely related to the maximum initial wave amplitude, suggesting that the deeper the water depth, the smaller the maximum wave amplitude will be (Fig. 8b).

Fig. 8a highlights the pronounced impact of slide volume on the a_M, demonstrating a direct correlation between the two variables. For instance, in the range of slide volumes we modelled (Fig. 8a), The smallest slide volume tested, measuring 0.10 × 10⁻³ m³, generated a low initial wave amplitude (a_M= 0.0066 m) (Table 4). In contrast, the largest volume tested, 6.25 × 10⁻³ m³, resulted in a significantly higher initial wave amplitude (a_M= 0.0319 m) (Table 4). The extremities of these results emphasize the slide volume’s paramount impact on wave amplitude, further elucidated by their positions as the smallest and largest a_M values across all conducted tests (Table 4). This is corroborated by findings from the literature (e.g., Murty, 2003), which align with the observed trend in our simulations.

The slope angle’s influence on a_M was smooth. A steady increase of wave amplitude was observed as the slope angle increased (Fig. 8c). In examining travel distance, an anomaly was identified. At a travel distance of 0.047 m, there was an unexpected dip in a_M, which deviates from the general increasing trend associated with longer travel distances. This singular instance could potentially be attributed to a numerical error. Beyond this point, the expected pattern of increasing a_M with longer travel distances resumes, suggesting that the anomaly at 0.047 m is an outlier in an otherwise consistent trend, and thus this single data point was overlooked while deriving the predictive equation. Regarding the inverse relationship between water depth and wave amplitude, our result (Fig. 8b) is consistent with previous reports by Fritz et al. (2003), (2004), and Watts et al. (2005).

The insights from Fig. 8 informed the architecture of the predictive equation in the next Section, with slide volume, travel distance, and slope angle being multiplicatively linked to wave amplitude underscoring their direct correlations with wave amplitude. Conversely, water depth is incorporated as a divisor, representing its inverse relationship with wave amplitude. This structure encapsulates the dynamics between the landslide parameters and their influence on the maximum initial wave amplitude as discussed in more detail in the next Section.

3.3. Predictive equation

Building on our sensitivity analysis of landslide parameters, as detailed in Section 3.2, and utilizing our nondimensional dataset, we have derived a new predictive equation as follows:(5)��/ℎ=0.015(tan�)0.10(�ℎ3)0.90(�ℎ)0.10(ℎ�)−0.11where, V is sliding volume, h is water depth, α is slope angle, and s is landslide thickness. It is important to note that this equation is valid only for subaerial solid-block landslide tsunamis as all our experiments were for this type of waves. The performance of this equation in predicting simulation data is demonstrated by the satisfactory alignment of data points around a 45° line, indicating its accuracy and reliability with regard to the experimental dataset (Fig. 9). The quality of fit between the dataset and Eq. (5) is 91 % indicating that Eq. (5) represents the dataset very well. Table 5 presents Eq. (5) alongside four other similar equations previously published. Two significant distinctions between our Eq. (5) and these others are: (i) Eq. (5) is derived from 3D experiments, whereas the other four equations are based on 2D experiments. (ii) Unlike the other equations, our Eq. (5) incorporates travel distance as an independent parameter.

Table 5. Performance comparison among our newly-developed equation and existing equations for estimating the maximum initial amplitude (a_M) of the 2018 Anak Krakatau subaerial landslide tsunami. Parameters: a_M, initial maximum wave amplitude; h, water depth; v_s, landslide velocity; V, slide volume; b_s, slide width; l_s, slide length; s, slide thickness; α, slope angle; and ��, volume of the final immersed landslide. We considered ��= V as the slide volume.

Event	Predictive equations	Author (year)	Observed a_M (m) ^⁎⁎	Calculated a_M (m)	Error, ε (%) ^⁎⁎⁎⁎
2018 Anak Krakatau tsunami (Subaerial landslide) *	��/ℎ=1.32��ℎ	Noda (1970)	134	134	0
	��/ℎ=0.667(0.5(��ℎ)2)0.334(��)0.754(��)0.506(�ℎ)1.631	Bolin et al. (2014) ^⁎⁎⁎	134	5942	4334
	��/ℎ=0.25(��ℎ2)0.8	Robbe-Saule et al. (2021)	134	31	77
	��/ℎ=0.4545(tan�)0.062(�ℎ3)0.296(ℎ�)−0.235	Sabeti and Heidarzadeh (2022b)	134	126	6
	��/ℎ=0.015(tan�)0.10(�ℎ3)0.911(�ℎ)0.10(ℎ�)−0.11	This study	134	130	2.9

⁎

Geometrical and kinematic parameters of the 2018 Anak Krakatau subaerial landslide based on Heidarzadeh et al. (2020), Grilli et al. (2019) and Grilli et al. (2021): V=2.11 × 10⁷ m³, h= 50 m; s= 114 m; α= 45°; l_s=1250 m; b_s= 2700 m; v_s=44.9 m/s; D= 2500 m; a_M= 100 m −150 m.⁎⁎

a_M= An average value of a_M = 134 m is considered in this study.⁎⁎⁎

The equation of Bolin et al. (2014) is based on the reformatted one reported by Lindstrøm (2016).⁎⁎⁎⁎

Error is calculated using Eq. (1), where the calculated a_M is assumed as the simulated value.

Additionally, we evaluated the performance of this equation using the real-world data from the 2018 Anak Krakatau subaerial landslide tsunami. Based on previous studies (Heidarzadeh et al., 2020; Grilli et al., 2019, 2021), we were able to provide a list of parameters for the subaerial landslide and associated tsunami for the 2018 Anak Krakatau event (see footnote of Table 5). We note that the data of the 2018 Anak Krakatau event was not used while deriving Eq. (5). The results indicate that Eq. (5) predicts the initial amplitude of the 2018 Anak Krakatau tsunami as being 130 m indicating an error of 2.9 % compared to the reported average amplitude of 134 m for this event. This performance indicates an improvement compared to the previous equation reported by Sabeti and Heidarzadeh (2022a) (Table 5). In contrast, the equations from Robbe-Saule et al. (2021) and Bolin et al. (2014) demonstrate higher discrepancies of 4200 % and 77 %, respectively (Table 5). Although Noda’s (1970) equation reproduces the tsunami amplitude of 134 m accurately (Table 5), it is crucial to consider its limitations, notably not accounting for parameters such as slope angle and travel distance.

It is essential to recognize that both travel distance and slope angle significantly affect wave amplitude. In our model, captured in Eq. (5), we integrate the slope angle (α) through the tangent function, i.e., tan α. This choice diverges from traditional physical interpretations that often employ the cosine or sine function (e.g., Heller and Hager, 2014; Watts et al., 2003). We opted for the tangent function because it more effectively reflects the direct impact of slope steepness on wave generation, yielding superior estimations compared to conventional methods.

The significance of this study lies in its application of both physical and numerical 3D experiments and the derivation of a predictive equation based on 3D results. Prior research, e.g. Heller et al. (2016), has reported notable discrepancies between 2D and 3D wave amplitudes, highlighting the important role of 3D experiments. It is worth noting that the suitability of applying an equation derived from either 2D or 3D data depends on the specific geometry and characteristics inherent in the problem being addressed. For instance, in the case of a long, narrow dam reservoir, an equation derived from 2D data would likely be more suitable. In such contexts, the primary dynamics of interest such as flow patterns and potential wave propagation are predominantly two-dimensional, occurring along the length and depth of the reservoir. This simplification to 2D for narrow dam reservoirs allows for more accurate modelling of these dynamics.

This study specifically investigates waves initiated by landslides, focusing on those characterized as solid blocks instead of granular flows, with slope angles confined to a range of 25° to 60°. We acknowledge the additional complexities encountered in real-world scenarios, such as dynamic density and velocity of landslides, which could affect the estimations. The developed equation in this study is specifically designed to predict the maximum initial amplitude of tsunamis for the aforementioned specified ranges and types of landslides.

4. Conclusions

Both physical and numerical experiments were undertaken in a 3D wave basin to study solid-block landslide-generated waves and to formulate a predictive equation for their maximum initial wave amplitude. At the beginning, two physical experiments were performed to validate and calibrate a 3D numerical model, which was subsequently utilized to generate 100 experiments by varying different landslide parameters. The generated database was then used to derive a predictive equation for the maximum initial wave amplitude of landslide tsunamis. The main features and outcomes are:

•The predictive equation of this study is exclusively derived from 3D data and exhibits a fitting quality of 91 % when applied to the database.
•For the first time, landslide travel distance was considered in the predictive equation. This inclusion provides more accuracy and flexibility for applying the equation.
•To further evaluate the performance of the predictive equation, it was applied to a real-world subaerial landslide tsunami (i.e., the 2018 Anak Krakatau event) and delivered satisfactory performance.

CRediT authorship contribution statement

Ramtin Sabeti: Conceptualization, Methodology, Validation, Software, Visualization, Writing – review & editing. Mohammad Heidarzadeh: Methodology, Data curation, Software, Writing – review & editing.

Declaration of competing interest

The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper.

Funding

RS is supported by the Leverhulme Trust Grant No. RPG-2022-306. MH is funded by open funding of State Key Lab of Hydraulics and Mountain River Engineering, Sichuan University, grant number SKHL2101. We acknowledge University of Bath Institutional Open Access Fund. MH is also funded by the Great Britain Sasakawa Foundation grant no. 6217 (awarded in 2023).

Acknowledgements

Authors are sincerely grateful to the laboratory technician team, particularly Mr William Bazeley, at the Faculty of Engineering, University of Bath for their support during the laboratory physical modelling of this research. We appreciate the valuable insights provided by Mr. Brian Fox (Senior CFD Engineer at Flow Science, Inc.) regarding air entrainment modelling in FLOW-3D HYDRO. We acknowledge University of Bath Institutional Open Access Fund.

Data availability

All data used in this study are given in the body of the article.

References

Baptista et al., 2020M.A. Baptista, J.M. Miranda, R. Omira, I. El-HussainStudy of the 24 September 2013 Oman Sea tsunami using linear shallow water inversionArab. J. Geosci., 13 (14) (2020), p. 606View in Scopus Google Scholar
Bolin et al., 2014H. Bolin, Y. Yueping, C. Xiaoting, L. Guangning, W. Sichang, J. ZhibingExperimental modeling of tsunamis generated by subaerial landslides: two case studies of the Three Gorges Reservoir, ChinaEnviron. Earth Sci., 71 (2014), pp. 3813-3825View at publisher CrossRef View in Scopus Google Scholar
Borrero et al., 2020J.C. Borrero, T. Solihuddin, H.M. Fritz, P.J. Lynett, G.S. Prasetya, V. Skanavis, S. Husrin, Kushendratno, W. Kongko, D.C. Istiyanto, A. DaulatField survey and numerical modelling of the December 22, 2018, Anak Krakatau TsunamiPure Appl. Geophys, 177 (2020), pp. 2457-2475View at publisher CrossRef View in Scopus Google Scholar
Chen et al., 2020F. Chen, V. Heller, R. BrigantiNumerical modelling of tsunamis generated by iceberg calving validated with large-scale laboratory experimentsAdv. Water Resour., 142 (2020), Article 103647View PDF View article View in Scopus Google Scholar
Courant et al., 1928R. Courant, K. Friedrichs, H. LewyÜber die partiellen Differenzengleichungen der mathematischen PhysikMath. Ann., 100 (1) (1928), pp. 32-74View in Scopus Google Scholar
Ersoy et al., 2019H. Ersoy, M. Karahan, K. Gelişli, A. Akgün, T. Anılan, M.O. Sünnetci, B.K. YahşiModelling of the landslide-induced impulse waves in the Artvin Dam reservoir by empirical approach and 3D numerical simulationEng. Geol., 249 (2019), pp. 112-128View PDF View article View in Scopus Google Scholar
Flow Science 2023Flow Science. (2023). Flow-3D Hydro version 12.0 user’s manual. Santa Fe, NM, USA. Retrieved from https://www.flow3d.com/. 6 Aug 2023.Google Scholar
Fritz, 2002H.M. FritzDoctoral DissertationETH Zurich (2002)Google Scholar
Fritz et al., 2003H.M. Fritz, W.H. Hager, H.E. MinorLandslide generated impulse waves. 1. Instantaneous flow fieldsExp. Fluids, 35 (2003), pp. 505-519View in Scopus Google Scholar
Fritz et al., 2004H.M. Fritz, W.H. Hager, H.E. MinorNear field characteristics of landslide generated impulse wavesJ. Waterw. Port Coastal Ocean Eng., 130 (6) (2004), pp. 287-302View in Scopus Google Scholar
Geertsema et al., 2022M. Geertsema, B. Menounos, G. Bullard, J.L. Carrivick, J.J. Clague, C. Dai, D. Donati, G. Ekstrom, J.M. Jackson, P. Lynett, M. PichierriThe 28 Nov 2020 landslide, tsunami, and outburst flood – a hazard cascade associated with rapid deglaciation at Elliot Creek, BC, CanadaGeophys. Res. Lett., 49 (6) (2022)Google Scholar
Grilli et al., 2021S.T. Grilli, C. Zhang, J.T. Kirby, A.R. Grilli, D.R. Tappin, S.F.L. Watt, J.E. Hunt, A. Novellino, S. Engwell, M.E.M. Nurshal, M. AbdurrachmanModeling of the Dec. 22nd, 2018, Anak Krakatau volcano lateral collapse and tsunami based on recent field surveys: comparison with observed tsunami impactMar. Geol., 440 (2021), Article 106566View PDF View article View in Scopus Google Scholar
Grilli et al., 2019S.T. Grilli, D.R. Tappin, S. Carey, S.F. Watt, S.N. Ward, A.R. Grilli, S.L. Engwell, C. Zhang, J.T. Kirby, L. Schambach, M. MuinModelling of the tsunami from the Dec. 22, 2018, lateral collapse of Anak Krakatau volcano in the Sunda Straits, IndonesiaSci. Rep., 9 (1) (2019), p. 11946 View at publisher This article is free to access.View in Scopus Google Scholar
Heidarzadeh et al., 2023M. Heidarzadeh, A.R. Gusman, I.E. MuliaThe landslide source of the eastern Mediterranean tsunami on 6 Feb 2023 following the Mw 7.8 Kahramanmaraş (Türkiye) inland earthquakeGeosci. Lett., 10 (1) (2023), p. 50 View at publisher This article is free to access.View in Scopus Google Scholar
Heidarzadeh et al., 2022M. Heidarzadeh, A.R. Gusman, A. Patria, B.T. WidyantoroPotential landslide origin of the Seram Island tsunami in Eastern Indonesia on 16 June 2021 following an Mw 5.9 earthquakeBull. Seismol. Soc. Am., 112 (5) (2022), pp. 2487-2498View at publisher CrossRef View in Scopus Google Scholar
Heidarzadeh et al., 2020M. Heidarzadeh, T. Ishibe, O. Sandanbata, A. Muhari, A.B. WijanartoNumerical modeling of the subaerial landslide source of the 22 Dec 2018 Anak Krakatoa volcanic tsunami, IndonesiaOcean. Eng., 195 (2020), Article 106733View PDF View article View in Scopus Google Scholar
Heidarzadeh et al., 2017M. Heidarzadeh, T. Harada, K. Satake, T. Ishibe, T. TakagawaTsunamis from strike-slip earthquakes in the Wharton Basin, northeast Indian Ocean: March 2016 M w7. 8 event and its relationship with the April 2012 M w 8.6 eventGeophys. J. Int., 211 (3) (2017), pp. 1601-1612, 10.1093/gji/ggx395 View at publisher This article is free to access.View in Scopus Google Scholar
Heller et al., 2008V. Heller, W.H. Hager, H.E. MinorScale effects in subaerial landslide generated impulse wavesExp. Fluids, 44 (2008), pp. 691-703View at publisher CrossRef View in Scopus Google Scholar
Heller and Hager, 2014V. Heller, W.H. HagerA universal parameter to predict subaerial landslide tsunamis?J. Mar. Sci. Eng., 2 (2) (2014), pp. 400-412View at publisher CrossRef View in Scopus Google Scholar
Heller and Spinneken, 2015V. Heller, J. SpinnekenOn the effect of the water body geometry on landslide–tsunamis: physical insight from laboratory tests and 2D to 3D wave parameter transformationCoastal Eng., 104 (2015), pp. 113-134View PDF View article View in Scopus Google Scholar
Heller et al., 2016V. Heller, M. Bruggemann, J. Spinneken, B.D. RogersComposite modelling of subaerial landslide–tsunamis in different water body geometries and novel insight into slide and wave kinematicsCoastal Eng., 109 (2016), pp. 20-41View PDF View article View in Scopus Google Scholar
Hirt, 2003C.W. HirtModeling Turbulent Entrainment of Air at a Free SurfaceFlow Science, Inc (2003)Google Scholar
Hu et al., 2023G. Hu, K. Satake, L. Li, P. DuOrigins of the tsunami following the 2023 Turkey–Syria earthquakeGeophys. Res. Lett., 50 (18) (2023)Google Scholar
Hu et al., 2022G. Hu, W. Feng, Y. Wang, L. Li, X. He, Ç. Karakaş, Y. TianSource characteristics and exacerbated tsunami hazard of the 2020 Mw 6.9 Samos earthquake in Eastern Aegean SeaJ. Geophys. Res., 127 (5) (2022)e2022JB023961Google Scholar
Iorio et al., 2021V. Iorio, G. Bellotti, C. Cecioni, S.T. GrilliA numerical model for the efficient simulation of multiple landslide-induced tsunamis scenariosOcean Model, 168 (2021), Article 101899View PDF View article View in Scopus Google Scholar
Kestin et al., 1978J. Kestin, M. Sokolov, W.A. WakehamViscosity of liquid water in the range− 8 C to 150 CJPCRD, 7 (3) (1978), pp. 941-948View at publisher CrossRef View in Scopus Google Scholar
Kim et al., 2020G.B. Kim, W. Cheng, R.C. Sunny, J.J. Horrillo, B.C. McFall, F. Mohammed, H.M. Fritz, J. Beget, Z. KowalikThree-dimensional landslide generated tsunamis: numerical and physical model comparisonsLandslides, 17 (2020), pp. 1145-1161View at publisher CrossRef View in Scopus Google Scholar
Kirby et al., 2022J.T. Kirby, S.T. Grilli, J. Horrillo, P.L.F. Liu, D. Nicolsky, S. Abadie, B. Ataie-Ashtiani, M.J. Castro, L. Clous, C. Escalante, I. Fine, J.M. González-Vida, F. Løvholt, P. Lynett, G. Ma, J. Macías, S. Ortega, F. Shi, S. Yavari-Ramshe, C. ZhangValidation and inter-comparison of models for landslide tsunami generationOcean Model., 170 (2022), Article 101943View PDF View article View in Scopus Google Scholar
Li et al., 2019G. Li, G. Chen, P. Li, H. JingEfficient and accurate 3-D numerical modelling of landslide tsunamiWater, 11 (10) (2019), p. 2033View at publisher CrossRef View in Scopus Google Scholar
MathWorks 2023MathWorksMATLAB User ManualThe MathWorks Inc., MA, USA (2023), p. 282Google Scholar
McFall and Fritz, 2016B.C. McFall, H.M. FritzPhysical modelling of tsunamis generated by three-dimensional deformable granular landslides on planar and conical island slopesProc. R. Soc. A. Math. Phys. Eng. Sci., 472 (2188) (2016), Article 20160052View at publisher CrossRef Google Scholar
Mulia et al., 2020aI.E. Mulia, S. Watada, T.C. Ho, K. Satake, Y. Wang, A. AditiyaSimulation of the 2018 tsunami due to the flank failure of Anak Krakatau volcano and implication for future observing systemsGeophys. Res. Lett., 47 (14) (2020), Article e2020GL087334 View at publisher This article is free to access.View in Scopus Google Scholar
Murty, 2003T.S. MurtyTsunami wave height dependence on landslide volumePure Appl. Geophys., 160 (2003), pp. 2147-2153View in Scopus Google Scholar
Mulia et al., 2020bI.E. Mulia, S. Watada, T.C. Ho, K. Satake, Y. Wang, A. AditiyaSimulation of the 2018 tsunami due to the flank failure of Anak Krakatau volcano and implication for future observing systemsGeophys. Res. Lett., 47 (14) (2020)Google Scholar
Mulligan et al., 2020R.P. Mulligan, A. Franci, M.A. Celigueta, W.A. TakeSimulations of landslide wave generation and propagation using the particle finite element methodJ. Geophys. Res. Oceans, 125 (6) (2020)Google Scholar
Najafi-Jilani and Ataie-Ashtiani, 2008A. Najafi-Jilani, B. Ataie-AshtianiEstimation of near-field characteristics of tsunami generation by submarine landslideOcean Eng., 35 (5) (2008), pp. 545-557View PDF View article View in Scopus Google Scholar
Onnen et al., 1997C. Onnen, R. Babuška, U. Kaymak, J.M. Sousa, H.B. Verbruggen, R. IsermannGenetic algorithms for optimization in predictive controlControl Eng. Pract, 5 (10) (1997), pp. 1363-1372View PDF View article View in Scopus Google Scholar
Panizzo et al. 2005A. Panizzo, P. De Girolamo, M. Di Risio, A. Maistri, A. PetacciaGreat landslid event in Italian artificial reservoirsNat. Hazards Earth Syst. Sci., 5 (5) (2005), pp. 733-740View at publisher CrossRef View in Scopus Google Scholar
Ren et al., 2020Z. Ren, Y. Wang, P. Wang, J. Hou, Y. Gao, L. ZhaoNumerical study of the triggering mechanism of the 2018 Anak Krakatau tsunami: eruption or collapsed landslide?Nat. Hazards, 102 (2020), pp. 1-13View in Scopus Google Scholar
Robbe-Saule et al., 2021M. Robbe-Saule, C. Morize, Y. Bertho, A. Sauret, A. Hildenbrand, P. GondretFrom laboratory experiments to geophysical tsunamis generated by subaerial landslidesSci. Rep., 11 (1) (2021), pp. 1-9Google Scholar
Sabeti and Heidarzadeh, 2022aR. Sabeti, M. HeidarzadehNumerical simulations of water waves generated by subaerial granular and solid-block landslides: validation, comparison, and predictive equationsOcean Eng., 266 (2022), Article 112853View PDF View article View in Scopus Google Scholar
Sabeti and Heidarzadeh, 2022bR. Sabeti, M. HeidarzadehA new empirical equation for predicting the maximum initial amplitude of submarine landslide-generated wavesLandslides, 19 (2) (2022), pp. 491-503 View at publisher This article is free to access.CrossRef View in Scopus Google Scholar
Sabeti et al. 2024R. Sabeti, M. Heidarzadeh, A. Romano, G. Barajas Ojeda, J.L. LaraThree-Dimensional Simulations of Subaerial Landslide-Generated Waves: Comparing OpenFOAM and FLOW-3D HYDRO ModelsPure Appl. Geophys. (2024), 10.1007/s00024-024-03443-x View at publisher This article is free to access.Google Scholar
Si et al., 2018P. Si, H. Shi, X. YuA general numerical model for surface waves generated by granular material intruding into a water bodyCoastal Eng., 142 (2018), pp. 42-51View PDF View article View in Scopus Google Scholar
Sorensen, 2010R.M. SorensenBasic Coastal Engineering(3rd edition), Springer Science & Business Media (2010), p. 324Google Scholar
Syamsidik et al., 2020Benazir Syamsidik, M. Luthfi, A. Suppasri, L.K. ComfortThe 22 December 2018 Mount Anak Krakatau volcanogenic tsunami on Sunda Strait coasts, Indonesia: tsunami and damage characteristicsNat. Hazards Earth Syst. Sci., 20 (2) (2020), pp. 549-565View in Scopus Google Scholar
Synolakis et al., 2002C.E. Synolakis, J.P. Bardet, J.C. Borrero, H.L. Davies, E.A. Okal, E.A. Silver, D.R. TappinThe slump origin of the 1998 Papua New Guinea tsunamiProc. R. Soc. Lond. A Math. Phys. Eng. Sci., 45 (2002), pp. 763-789View in Scopus Google Scholar
Wang et al., 2022Y. Wang, H.Y. Su, Z. Ren, Y. MaSource properties and resonance characteristics of the tsunami generated by the 2021 M 8.2 Alaska earthquakeJ. Geophys. Res. Oceans, 127 (3) (2022), Article e2021JC018308 View at publisher This article is free to access.View in Scopus Google Scholar
Wang et al., 2021Y. Wang, M. Heidarzadeh, K. Satake, G. HuCharacteristics of two tsunamis generated by successive M w 7.4 and M w 8.1 earthquakes in Kermadec Islands on March 4, 2021Nat. Haz. Earth Sys. Sci., 22 (2021), pp. 1073-1082, 10.5194/nhess-22-1073-2022 View at publisher View in Scopus Google Scholar
Watts et al., 2005P. Watts, S.T. Grilli, D.R. Tappin, G.J. FryerTsunami generation by submarine mass failure. II: predictive equations and case studiesJ. Waterw. Port Coast. Ocean Eng., 131 (6) (2005), pp. 298-310View in Scopus Google Scholar
Watts et al., 2003P. Watts, S.T. Grilli, J.T. Kirby, G.J. Fryer, D.R. TappinLandslide tsunami case studies using a Boussinesq model and a fully nonlinear tsunami generation modelNat. Hazards Earth Sys. Sci., 3 (5) (2003), pp. 391-402View at publisher CrossRef View in Scopus Google Scholar
Watts, 1998P. WattsWavemaker curves for tsunamis generated by underwater landslidesJ. Waterw. Port. Coast. Ocean. Eng., 124 (3) (1998), pp. 127-137Google Scholar
Zhang et al., 2021C. Zhang, J.T. Kirby, F. Shi, G. Ma, S.T. GrilliA two-layer non-hydrostatic landslide model for tsunami generation on irregular bathymetry. 2. Numerical discretization and model validationOcean Model., 160 (2021), Article 101769View PDF View article View in Scopus Google Scholar

PDF 원문 보기

Numerical Investigation of the Local Scour for Tripod Pile Foundation.

Hassan, Waqed H.; Fadhe, Zahraa Mohammad; Thiab, Rifqa F.; Mahdi, Karrar

초록

This work investigates numerically a local scour moves in irregular waves around tripods. It is constructed and proven to use the numerical model of the seabed-tripodfluid with an RNG k turbulence model. The present numerical model then examines the flow velocity distribution and scour characteristics. After that, the suggested computational model Flow-3D is a useful tool for analyzing and forecasting the maximum scour development and the flow field in random waves around tripods. The scour values affecting the foundations of the tripod must be studied and calculated, as this phenomenon directly and negatively affects the structure of the structure and its design life. The lower diagonal braces and the main column act as blockages, increasing the flow accelerations underneath them. This increases the number of particles that are moved, which in turn creates strong scouring in the area. The numerical model has a good agreement with the experimental model, with a maximum percentage of error of 10% between the experimental and numerical models. In addition, Based on dimensional analysis parameters, an empirical equation has been devised to forecast scour depth with flow depth, median size ratio, Keulegan-Carpenter (Kc), Froud number flow, and wave velocity that the results obtained in this research at various flow velocities and flow depths demonstrated that the maximum scour depth rate depended on wave height with rising velocities and decreasing particle sizes (d50) and the scour depth attains its steady-current value for Vw < 0.75. As the Froude number rises, the maximum scour depth will be large.

주제어

BUILDING foundations; SURFACE waves (Seismic waves); FLOW velocity; RANDOM fields; DIMENSIONAL analysis; FROUDE number; OCEAN waves

키워드

출판물

Mathematical Modelling of Engineering Problems, 2024, Vol 11, Issue 4, p903

ISSN 2369-0739

저자 소속기관

¹ Civil Engineering Department, Faculty of Engineering, University of Warith Al-Anbiyaa, Kerbala 56001, Iraq
² Civil Engineering Department, Faculty of Engineering, University of Kerbala, Kerbala 56001, Iraq
³ Department of Radiological Techniques, College of Health and Medical Techniques, Al-Zahraa University for Women, Karbala 56100, Iraq
⁴ Soil Physics and Land Management Group, Wageningen University & Research, Wageningen 6708 PB, Netherlands

Embankment Dams Overtopping Breach: A Numerical Investigation of Hydraulic Results

Mahdi Ebrahimi, Mirali Mohammadi, Sayed Mohammad Hadi Meshkati & Farhad Imanshoar

Abstract

The overtopping breach is the most probable reason of embankment dam failures. Hence, the investigation of the mentioned phenomenon is one of the vital hydraulic issues. This research paper tries to utilize three numerical models, i.e., BREACH, HEC-RAS, and FLOW-3D for modeling the hydraulic outcomes of overtopping breach phenomenon. Furthermore, the outputs have been compared with experimental model results given by authors. The BREACH model presents a desired prediction for the peak flow. The HEC-RAS model has a more realistic performance in terms of the peak flow prediction, its occurrence time (5-s difference with observed status), and maximum flow depth. The variations diagram in the reservoir water level during the breach process has a descending trend. Whereas it initially ascended; and then, it experienced a descending trend in the observed status. The FLOW-3D model computes the flow depth, flow velocity, and Froude number due to the physical model breach. Moreover, it revealed a peak flow damping equals to 5% and 5-s difference in the peak flow occurrence time at 4-m distance from the physical model downstream. In addition, the current research work demonstrates the mentioned numerical models and provides a possible comprehensive perspective for a dam breach scope. They also help to achieve the various hydraulic parameters computations. Besides, they may calculate unmeasured parameters using the experimental data.

월류 현상은 제방 댐 실패의 가장 유력한 원인입니다. 따라서 언급된 현상에 대한 조사는 중요한 수리학적 문제 중 하나입니다.

본 연구 논문에서는 월류 침해 현상의 수리적 결과를 모델링하기 위해 BREACH, HEC-RAS 및 FLOW-3D의 세 가지 수치 모델을 활용하려고 합니다. 또한 출력은 저자가 제공한 실험 모델 결과와 비교되었습니다. BREACH 모델은 최대 유량에 대해 원하는 예측을 제시합니다.

HEC-RAS 모델은 최고유량 예측, 발생시간(관찰상태와 5초 차이), 최대유량수심 측면에서 보다 현실적인 성능을 가지고 있습니다. 위반 과정 중 저수지 수위의 변동 다이어그램은 감소하는 추세를 보입니다. 처음에는 상승했지만 그런 다음 관찰된 상태가 감소하는 추세를 경험했습니다.

FLOW-3D 모델은 물리적 모델 위반으로 인한 흐름 깊이, 흐름 속도 및 Froude 수를 계산합니다. 또한, 실제 모델 하류로부터 4m 거리에서 최대유량 발생시간이 5%, 5초 차이에 해당하는 최대유량 감쇠를 나타냈습니다.

또한, 현재 연구 작업은 언급된 수치 모델을 보여주고 댐 침해 범위에 대한 가능한 포괄적인 관점을 제공합니다. 또한 다양한 유압 매개변수 계산을 수행하는 데 도움이 됩니다. 게다가 실험 데이터를 사용하여 측정되지 않은 매개변수를 계산할 수도 있습니다.

Keywords

DOI

https://doi.org/10.1007/s40996-024-01387-9

Fig. 1View in article
Fig. 2
View in article
Fig. 3View in article
Fig. 4View in article
Fig. 5View in article
Fig. 6View in article
Fig. 7View in article
Fig. 8View in article
Fig. 9View in article
Fig. 10View in article

References

Association of state dam safety officials (2023) Kentucky, USA. Available from https://damsafety.org
ASTM D1557 (2007) Standard test methods for laboratory compaction characteristics of soil using standard effort. West Conshohocken, PA, USA
ASTM D422–63 (2002) Standard test method for particle size analysis of soils
Azimi H, Shabanlou S (2016) Comparison of subcritical and supercritical flow patterns within triangular channels along the side weir. Int J Nonlinear Sci Numer Simul 17(7–8):361–368Article MathSciNet Google Scholar
Azimi H, Shabanlou S (2018) Numerical study of bed slope change effect of circular channel with side weir in supercritical flow conditions. Appl Water Sci 8(6):166Article ADS Google Scholar
Azimi H, Shabanlou S, Kardar S (2017) Characteristics of hydraulic jump in U-shaped channels. Arab J Sci Eng 42:3751–3760Article Google Scholar
Brunner GW (2016) HEC-RAS Reference Manual, version 5.0. Hydrologic Engineering Center, Institute for Water Resources, US Army Corps of Engineers, Davis, California
Brunner GW (2016) HEC-RAS user^’s Manual, version 5.0. Hydrologic Engineering Center, Institute for Water Resources, US Army Corps of Engineers, Davis, California
Chanson H, Wang H (2013) Unsteady discharge calibration of a large V-notch weir. Flow Meas Instrum 29:19–24Article Google Scholar
Committee on Dam Safety (2019) ICOLD incident database bulletin 99 update: statistical analysis of dam failures, technical report, international commission on large dams. Available from: https://www.icoldchile.cl/boletines/188.pdf
Engomoen B, Witter DT, Knight K, Luebke TA (2014) Design Standards No 13: Embankment Dams. United States Bureau of Reclamation
Flow Science Corporation (2017) Flow-3D v11.0 User Manual. Available from: http://flow3d.com
Froehlich DC (2016) Predicting peak discharge from gradually breached embankment dam. J Hydrol Eng 21(11):04016041Article Google Scholar
Hakimzadeh H, Nourani V, Amini AB (2014) Genetic programming simulation of dam breach hydrograph and peak outflow discharge. J Hydrol Eng 19:757–768Article Google Scholar
Hooshyaripor F, Tahershamsi A, Golian S (2014) Application of copula method and neural networks for predicting peak outflow from breached embankments. J Hydro-Environ Res 8(3):292–303Article Google Scholar
Irmakunal CI (2019) Two-dimensional dam break analyses of Berdan dam. MSC thesis, Middle East Technical University, Turkey
kumar Gupta A, Narang I, Goyal P, (2020) Dam break analysis of JAWAI dam PALI, Rajasthan using HEC-RAS. IOSR J Mech Civ Eng 17(2):43–52Google Scholar
Mo C, Cen W, Le X, Ban H, Ruan Y, Lai S, Shen Y (2023) Simulation of dam-break flood and risk assessment: a case study of Chengbi river dam in Baise, China. J Hydroinformatics 25(4):1276–1294Article Google Scholar
Morris M, Kortenhaus A, Visser P (2009) Modelling breach initiation and growth. FLOODsite report: T06–08–02, FLOODsite Consortium, Wallingford, UK
Novak P, Moffat AIB, Nalluri C, Narayanan RAIB (2017) Hydraulic structures. CRC PressGoogle Scholar
Pierce MW, Thornton CI, Abt SR (2010) Predicting peak outflow from breached embankment dams. J Hydrol Eng 15(5):338–349Article Google Scholar
Saberi O (2016) Embankment dam failure outflow hydrograph development. PhD thesis, Graz University of Technology, Austria
Sylvestre J, Sylvestre P (2018) User’s guide for BRCH GUI. 2018. Available from: http://rivermechanics.net
USACE) 2004) General design and construction considerations for Earth and rockfill dams, US Army Corps of Engineers, Washington DC, USA
USBR (1987) Design of small dams, Bureau of Reclamation, Water Resources Technical Publication
Versteeg HK, Malalasekera W (2007) An introduction to computational fluid dynamics: the finite volume method. Pearson education
Wang Z, Bowles DS (2006) Three-dimensional non-cohesive earthen dam breach model. Part 1: theory and methodology. Adv Water Resour 29(10):1528–1545Article ADS Google Scholar
Webby MG (1996) Discussion of peak outflow from breached embankment dam by David C. Froehlich. J Water Resour Plan Manag 122(4):316–317
Wu W, Marsooli R, He Z (2012) Depth-averaged two-dimensional model of unsteady flow and sediment transport due to noncohesive embankment break/breaching. J Hydraul Eng 138(6):503–516Article Google Scholar
Xu Y, Zhang LM (2009) Breaching parameters for earth and rockfill dams. J Geotech Geoenviron Eng 135(12):1957–1970Article Google Scholar

Figure 1: Scheme of liquid metal printing process

Effect of Aging Heat Treatment in an Al-4008 Produced byLiquid Metal Printing

C. M. Ladeiro
Department of Metallurgical and Materials Engineering, Faculdade de Engenharia, Universidade do Porto, Rua Dr. Roberto
Frias, 4200-465 PORTO, Portugal (up201806112@fe.up.pt) ORCID 0009-0003-8587-2309
F. L. Nunes
Department of Metallurgical and Materials Engineering, Faculdade de Engenharia, Universidade do Porto, Rua Dr. Roberto
Frias, 4200-465 PORTO, Portugal (up201806193@fe.up.pt) ORCID 0009-0000-0988-4285
M. M. Trindade
Department of Metallurgical and Materials Engineering, Faculdade de Engenharia, Universidade do Porto, Rua Dr. Roberto
Frias, 4200-465 PORTO, Portugal (up201806438@fe.up.pt) ORCID 0009-0008-1397-5321
J. M. Costa
Department of Metallurgical and Materials Engineering, Faculdade de Engenharia, Universidade do Porto and LAETA/INEGI –
Institute of Science and Innovation in Mechanical and Industrial Engineering, Rua Dr. Roberto Frias, 4200-465 PORTO,
Portugal (jose.costa@fe.up.pt) ORCID 0000-0002-1714-4671

Abstract

In today’s world, additive manufacturing (AM) is one of the most popular technologies and has the potential to revolutionize the manufacturing industry. As one of the most recent advances in this industry, liquid metal printing has a growing value in the engineering field. This study aims to evaluate the effect of two heat treatment conditions in an Al-4008 alloy produced by this technique in the microstructure and mechanical properties. It was concluded that the heat treatment (HT) enhances the Si particle coalescence and Fe-rich intermetallic compound precipitation, increasing the sample hardness significantly (50%). Density analysis showed a slight porosity decrease with HT. Tensile tests indicated heat-treated, same-directionally pulled samples exhibited brittleness compared to as-printed ones, while HT increased both yield strength (245 MPa) and ultimate tensile strength (294 MPa).

오늘날 세계에서 적층 제조(AM)는 가장 인기 있는 기술 중 하나이며 제조 산업에 혁명을 일으킬 잠재력을 가지고 있습니다. 이 업계의 가장 최근 발전 중 하나인 액체 금속 인쇄는 엔지니어링 분야에서 그 가치가 커지고 있습니다. 본 연구는 이 기술로 생산된 Al-4008 합금의 두 가지 열처리 조건이 미세 구조 및 기계적 특성에 미치는 영향을 평가하는 것을 목표로 합니다. 열처리(HT)는 Si 입자 유착과 Fe가 풍부한 금속간 화합물 침전을 향상시켜 샘플 경도를 크게(50%) 증가시키는 것으로 결론지었습니다. 밀도 분석에서는 HT를 사용하면 다공성이 약간 감소하는 것으로 나타났습니다. 인장 테스트에서는 동일한 방향으로 당겨진 열처리된 샘플이 인쇄된 샘플에 비해 취성을 보인 반면, HT는 항복 강도(245MPa)와 최대 인장 강도(294MPa)를 모두 증가시켰습니다.

PDF Download

Coupled CFD-DEM simulation of interfacial fluid–particle interaction during binder jet 3D printing

바인더 제트 3D 프린팅 중 계면 유체-입자 상호 작용에 대한 CFD-DEM 결합 시뮬레이션

Joshua J. Wagner, C. Fred Higgs III

https://doi.org/10.1016/j.cma.2024.116747

Abstract

The coupled dynamics of interfacial fluid phases and unconstrained solid particles during the binder jet 3D printing process govern the final quality and performance of the resulting components. The present work proposes a computational fluid dynamics (CFD) and discrete element method (DEM) framework capable of simulating the complex interfacial fluid–particle interaction that occurs when binder microdroplets are deposited into a powder bed. The CFD solver uses a volume-of-fluid (VOF) method for capturing liquid–gas multifluid flows and relies on block-structured adaptive mesh refinement (AMR) to localize grid refinement around evolving fluid–fluid interfaces. The DEM module resolves six degrees of freedom particle motion and accounts for particle contact, cohesion, and rolling resistance. Fully-resolved CFD-DEM coupling is achieved through a fictitious domain immersed boundary (IB) approach. An improved method for enforcing three-phase contact lines with a VOF-IB extension technique is introduced. We present several simulations of binder jet primitive formation using realistic process parameters and material properties. The DEM particle systems are experimentally calibrated to reproduce the cohesion behavior of physical nickel alloy powder feedstocks. We demonstrate the proposed model’s ability to resolve the interdependent fluid and particle dynamics underlying the process by directly comparing simulated primitive granules with one-to-one experimental counterparts obtained from an in-house validation apparatus. This computational framework provides unprecedented insight into the fundamental mechanisms of binder jet 3D printing and presents a versatile new approach for process parameter optimization and defect mitigation that avoids the inherent challenges of experiments.

바인더 젯 3D 프린팅 공정 중 계면 유체 상과 구속되지 않은 고체 입자의 결합 역학이 결과 구성 요소의 최종 품질과 성능을 좌우합니다. 본 연구는 바인더 미세액적이 분말층에 증착될 때 발생하는 복잡한 계면 유체-입자 상호작용을 시뮬레이션할 수 있는 전산유체역학(CFD) 및 이산요소법(DEM) 프레임워크를 제안합니다.

CFD 솔버는 액체-가스 다중유체 흐름을 포착하기 위해 VOF(유체량) 방법을 사용하고 블록 구조 적응형 메쉬 세분화(AMR)를 사용하여 진화하는 유체-유체 인터페이스 주위의 그리드 세분화를 국지화합니다. DEM 모듈은 6개의 자유도 입자 운동을 해결하고 입자 접촉, 응집력 및 구름 저항을 설명합니다.

완전 분해된 CFD-DEM 결합은 가상 도메인 침지 경계(IB) 접근 방식을 통해 달성됩니다. VOF-IB 확장 기술을 사용하여 3상 접촉 라인을 강화하는 향상된 방법이 도입되었습니다. 현실적인 공정 매개변수와 재료 특성을 사용하여 바인더 제트 기본 형성에 대한 여러 시뮬레이션을 제시합니다.

DEM 입자 시스템은 물리적 니켈 합금 분말 공급원료의 응집 거동을 재현하기 위해 실험적으로 보정되었습니다. 우리는 시뮬레이션된 기본 과립과 내부 검증 장치에서 얻은 일대일 실험 대응물을 직접 비교하여 프로세스의 기본이 되는 상호 의존적인 유체 및 입자 역학을 해결하는 제안된 모델의 능력을 보여줍니다.

이 계산 프레임워크는 바인더 제트 3D 프린팅의 기본 메커니즘에 대한 전례 없는 통찰력을 제공하고 실험에 내재된 문제를 피하는 공정 매개변수 최적화 및 결함 완화를 위한 다용도의 새로운 접근 방식을 제시합니다.

Introduction

Binder jet 3D printing (BJ3DP) is a powder bed additive manufacturing (AM) technology capable of fabricating geometrically complex components from advanced engineering materials, such as metallic superalloys and ultra-high temperature ceramics [1], [2]. As illustrated in Fig. 1(a), the process is comprised of many repetitive print cycles, each contributing a new cross-sectional layer on top of a preceding one to form a 3D CAD-specified geometry. The feedstock material is first delivered from a hopper to a build plate and then spread into a thin layer by a counter-rotating roller. After powder spreading, a print head containing many individual inkjet nozzles traverses over the powder bed while precisely jetting binder microdroplets onto select regions of the spread layer. Following binder deposition, the build plate lowers by a specified layer thickness, leaving a thin void space at the top of the job box that the subsequent powder layer will occupy. This cycle repeats until the full geometries are formed layer by layer. Powder bed fusion (PBF) methods follow a similar procedure, except they instead use a laser or electron beam to selectively melt and fuse the powder material. Compared to PBF, binder jetting offers several distinct advantages, including faster build rates, enhanced scalability for large production volumes, reduced machine and operational costs, and a wider selection of suitable feedstock materials [2]. However, binder jetted parts generally possess inferior mechanical properties and reduced dimensional accuracy [3]. As a result, widescale adoption of BJ3DP to fabricate high-performance, mission-critical components, such as those common to the aerospace and defense sectors, is contingent on novel process improvements and innovations [4].

A major obstacle hindering the advancement of BJ3DP is our limited understanding of how various printing parameters and material properties collectively influence the underlying physical mechanisms of the process and their effect on the resulting components. To date, the vast majority of research efforts to uncover these relationships have relied mainly on experimental approaches [5], [6], [7], [8], [9], [10], [11], [12], [13], [14], [15], [16], [17], [18], [19], which are often expensive and time-consuming and have inherent physical restrictions on what can be measured and observed. For these reasons, there is a rapidly growing interest in using computational models to circumvent the challenges of experimental investigations and facilitate a deeper understanding of the process’s fundamental phenomena. While significant progress has been made in developing and deploying numerical frameworks aimed at powder spreading [20], [21], [22], [23], [24], [25], [26], [27] and sintering [28], [29], [30], [31], [32], simulating the interfacial fluid–particle interaction (IFPI) in the binder deposition stage is still in its infancy. In their exhaustive review, Mostafaei et al. [2] point out the lack of computational models capable of resolving the coupled fluid and particle dynamics associated with binder jetting and suggest that the development of such tools is critical to further improving the process and enhancing the quality of its end-use components.

We define IFPI as a multiphase flow regime characterized by immiscible fluid phases separated by dynamic interfaces that intersect the surfaces of moving solid particles. As illustrated in Fig. 1(b), an elaborate IFPI occurs when a binder droplet impacts the powder bed in BJ3DP. The momentum transferred from the impacting droplet may cause powder compaction, cratering, and particle ejection. These ballistic disturbances can have deleterious effects on surface texture and lead to the formation of large void spaces inside the part [5], [13]. After impact, the droplet spreads laterally on the bed surface and vertically into the pore network, driven initially by inertial impact forces and then solely by capillary action [33]. Attractive capillary forces exerted on mutually wetted particles tend to draw them inward towards each other, forming a packed cluster of bound particles referred to as a primitive [34]. A single-drop primitive is the most fundamental building element of a BJ3DP part, and the interaction leading to its formation has important implications on the final part characteristics, such as its mechanical properties, resolution, and dimensional accuracy. Generally, binder droplets are deposited successively as the print head traverses over the powder bed. The traversal speed and jetting frequency are set such that consecutive droplets coalesce in the bed, creating a multi-drop primitive line instead of a single-drop primitive granule. The binder must be jetted with sufficient velocity to penetrate the powder bed deep enough to provide adequate interlayer binding; however, a higher impact velocity leads to more pronounced ballistic effects.

A computational framework equipped to simulate the interdependent fluid and particle dynamics in BJ3DP would allow for unprecedented observational and measurement capability at temporal and spatial resolutions not currently achievable by state-of-the-art imaging technology, namely synchrotron X-ray imaging [13], [14], [18], [19]. Unfortunately, BJ3DP presents significant numerical challenges that have slowed the development of suitable modeling frameworks; the most significant of which are as follows:

1.Incorporating dynamic fluid–fluid interfaces with complex topological features remains a nontrivial task for standard mesh-based CFD codes. There are two broad categories encompassing the methods used to handle interfacial flows: interface tracking and interface capturing [35]. Interface capturing techniques, such as the popular volume-of-fluid (VOF) [36] and level-set methods [37], [38], are better suited for problems with interfaces that become heavily distorted or when coalescence and fragmentation occur frequently; however, they are less accurate in resolving surface tension and boundary layer effects compared to interface tracking methods like front-tracking [39], arbitrary Lagrangian–Eulerian [40], and space–time finite element formulations [41]. Since interfacial forces become increasingly dominant at decreasing length scales, inaccurate surface tension calculations can significantly deteriorate the fidelity of IFPI simulations involving <100 μm droplets and particles.
2.Dynamic powder systems are often modeled using the discrete element method (DEM) introduced by Cundall and Strack [42]. For IFPI problems, a CFD-DEM coupling scheme is required to exchange information between the fluid and particle solvers. Fully-resolved CFD-DEM coupling suggests that the flow field around individual particle surfaces is resolved on the CFD mesh [43], [44]. In contrast, unresolved coupling volume averages the effect of the dispersed solid phase on the continuous fluid phases [45], [46], [47], [48]. Comparatively, the former is computationally expensive but provides detailed information about the IFPI in question and is more appropriate when contact line dynamics are significant. However, since the pore structure of a powder bed is convoluted and evolves with time, resolving such solid–fluid interfaces on a computational mesh presents similar challenges as fluid–fluid interfaces discussed in the previous point. Although various algorithms have been developed to deform unstructured meshes to accommodate moving solid surfaces (see Bazilevs et al. [49] for an overview of such methods), they can be prohibitively expensive when frequent topology changes require mesh regeneration rather than just modification through nodal displacement. The pore network in a powder bed undergoes many topology changes as particles come in and out of contact with each other, constantly closing and opening new flow channels. Non-body-conforming structured grid approaches that rely on immersed boundary (IB) methods to embed the particles in the flow field can be better suited for such cases [50]. Nevertheless, accurately representing these complex pore geometries on Cartesian grids requires extremely high mesh resolutions, which can impose significant computational costs.
3.Capillary effects depend on the contact angle at solid–liquid–gas intersections. Since mesh nodes do not coincide with a particle surface when using an IB method on structured grids, imposing contact angle boundary conditions at three-phase contact lines is not straightforward.

While these issues also pertain to PBF process modeling, resolving particle motion is generally less crucial for analyzing melt pool dynamics compared to primitive formation in BJ3DP. Therefore, at present, the vast majority of computational process models of PBF assume static powder beds and avoid many of the complications described above, see, e.g., [51], [52], [53], [54], [55], [56], [57], [58], [59]. Li et al. [60] presented the first 2D fully-resolved CFD-DEM simulations of the interaction between the melt pool, powder particles, surrounding gas, and metal vapor in PBF. Following this work, Yu and Zhao [61], [62] published similar melt pool IFPI simulations in 3D; however, contact line dynamics and capillary forces were not considered. Compared to PBF, relatively little work has been published regarding the computational modeling of binder deposition in BJ3DP. Employing the open-source VOF code Gerris [63], Tan [33] first simulated droplet impact on a powder bed with appropriate binder jet parameters, namely droplet size and impact velocity. However, similar to most PBF melt pool simulations described in the current literature, the powder bed was fixed in place and not allowed to respond to the interacting fluid phases. Furthermore, a simple face-centered cubic packing of non-contacting, monosized particles was considered, which does not provide a realistic pore structure for AM powder beds. Building upon this approach, we presented a framework to simulate droplet impact on static powder beds with more practical particle size distributions and packing arrangements [64]. In a study similar to [33], [64], Deng et al. [65] used the VOF capability in Ansys Fluent to examine the lateral and vertical spreading of a binder droplet impacting a fixed bimodal powder bed with body-centered packing. Li et al. [66] also adopted Fluent to conduct 2D simulations of a 100 μm diameter droplet impacting substrates with spherical roughness patterns meant to represent the surface of a simplified powder bed with monosized particles. The commercial VOF-based software FLOW-3D offers an AM module centered on process modeling of various AM technologies, including BJ3DP. However, like the above studies, particle motion is still not considered in this codebase. Ur Rehman et al. [67] employed FLOW-3D to examine microdroplet impact on a fixed stainless steel powder bed. Using OpenFOAM, Erhard et al. [68] presented simulations of different droplet impact spacings and patterns on static sand particles.

Recently, Fuchs et al. [69] introduced an impressive multipurpose smoothed particle hydrodynamics (SPH) framework capable of resolving IFPI in various AM methods, including both PBF and BJ3DP. In contrast to a combined CFD-DEM approach, this model relies entirely on SPH meshfree discretization of both the fluid and solid governing equations. The authors performed several prototype simulations demonstrating an 80 μm diameter droplet impacting an unconstrained powder bed at different speeds. While the powder bed responds to the hydrodynamic forces imparted by the impacting droplet, the particle motion is inconsistent with experimental time-resolved observations of the process [13]. Specifically, the ballistic effects, such as particle ejection and bed deformation, were drastically subdued, even in simulations using a droplet velocity ∼ 5× that of typical jetting conditions. This behavior could be caused by excessive damping in the inter-particle contact force computations within their SPH framework. Moreover, the wetted particles did not appear to be significantly influenced by the strong capillary forces exerted by the binder as no primitive agglomeration occurred. The authors mention that the objective of these simulations was to demonstrate their codebase’s broad capabilities and that some unrealistic process parameters were used to improve computational efficiency and stability, which could explain the deviations from experimental observations.

In the present paper, we develop a novel 3D CFD-DEM numerical framework for simulating fully-resolved IFPI during binder jetting with realistic material properties and process parameters. The CFD module is based on the VOF method for capturing binder–air interfaces. Surface tension effects are realized through the continuum surface force (CSF) method with height function calculations of interface curvature. Central to our fluid solver is a proprietary block-structured AMR library with hierarchical octree grid nesting to focus enhanced grid resolution near fluid–fluid interfaces. The GPU-accelerated DEM module considers six degrees of freedom particle motion and includes models based on Hertz-Mindlin contact, van der Waals cohesion, and viscoelastic rolling resistance. The CFD and DEM modules are coupled to achieve fully-resolved IFPI using an IB approach in which Lagrangian solid particles are mapped to the underlying Eulerian fluid mesh through a solid volume fraction field. An improved VOF-IB extension algorithm is introduced to enforce the contact angle at three-phase intersections. This provides robust capillary flow behavior and accurate computations of the fluid-induced forces and torques acting on individual wetted particles in densely packed powder beds.

We deploy our integrated codebase for direct numerical simulations of single-drop primitive formation with powder beds whose particle size distributions are generated from corresponding laboratory samples. These simulations use jetting parameters similar to those employed in current BJ3DP machines, fluid properties that match commonly used aqueous polymeric binders, and powder properties specific to nickel alloy feedstocks. The cohesion behavior of the DEM powder is calibrated based on the angle of repose of the laboratory powder systems. The resulting primitive granules are compared with those obtained from one-to-one experiments conducted using a dedicated in-house test apparatus. Finally, we demonstrate how the proposed framework can simulate more complex and realistic printing operations involving multi-drop primitive lines.

Section snippets

Mathematical description of interfacial fluid–particle interaction

This section briefly describes the governing equations of fluid and particle dynamics underlying the CFD and DEM solvers. Our unified framework follows an Eulerian–Lagrangian approach, wherein the Navier–Stokes equations of incompressible flow are discretized on an Eulerian grid to describe the motion of the binder liquid and surrounding gas, and the Newton–Euler equations account for the positions and orientations of the Lagrangian powder particles. The mathematical foundation for

CFD solver for incompressible flow with multifluid interfaces

This section details the numerical methodology used in our CFD module to solve the Navier–Stokes equations of incompressible flow. First, we introduce the VOF method for capturing the interfaces between the binder and air phases. This approach allows us to solve the fluid dynamics equations considering only a single continuum field with spatial and temporal variations in fluid properties. Next, we describe the time integration procedure using a fractional-step projection algorithm for

DEM solver for solid particle dynamics

This section covers the numerical procedure for tracking the motion of individual powder particles with DEM. The Newton–Euler equations (Eqs. (10), (11)) are ordinary differential equations (ODEs) for which many established numerical integrators are available. In general, the most challenging aspects of DEM involve processing particle collisions in a computationally efficient manner and dealing with small time step constraints that result from stiff materials, such as metallic AM powders. The

Unified CFD-DEM solver

The preceding sections have introduced the CFD and DEM solution algorithms separately. Here, we discuss the integrated CFD-DEM solution algorithm and related details.

Binder jet process modeling and validation experiments

In this section, we deploy our CFD-DEM framework to simulate the IFPI occurring during the binder droplet deposition stage of the BJ3DP process. The first simulations attempt to reproduce experimental single-drop primitive granules extracted from four nickel alloy powder samples with varying particle size distributions. The experiments are conducted with a dedicated in-house test apparatus that allows for the precision deposition of individual binder microdroplets into a powder bed sample. The

Conclusions

This paper introduces a coupled CFD-DEM framework capable of fully-resolved simulation of the interfacial fluid–particle interaction occurring in the binder jet 3D printing process. The interfacial flow of binder and surrounding air is captured with the VOF method and surface tension effects are incorporated using the CSF technique augmented by height function curvature calculations. Block-structured AMR is employed to provide localized grid refinement around the evolving liquid–gas interface.

CRediT authorship contribution statement

Joshua J. Wagner: Conceptualization, Data curation, Formal analysis, Investigation, Methodology, Software, Visualization, Writing – original draft, Writing – review & editing. C. Fred Higgs III: Conceptualization, Funding acquisition, Investigation, Methodology, Project administration, Resources, Supervision, Writing – original draft, Writing – review & editing.

Declaration of competing interest

The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper.

Acknowledgments

This work was supported by a NASA Space Technology Research Fellowship, United States of America, Grant No. 80NSSC19K1171. Partial support was also provided through an AIAA Foundation Orville, USA and Wilbur Wright Graduate Award, USA . The authors would like to gratefully acknowledge Dr. Craig Smith of NASA Glenn Research Center for the valuable input he provided on this project.

References (155)

ZiaeeM. et al.Binder jetting: A review of process, materials, and methodsAddit. Manuf.(2019)
MostafaeiA. et al.Binder jet 3D printing—process parameters, materials, properties, modeling, and challengesProg. Mater. Sci.(2021)
MiyanajiH. et al.Effect of printing speed on quality of printed parts in binder jetting processAddit. Manuf.(2018)
CraneN.B.Impact of part thickness and drying conditions on saturation limits in binder jet additive manufacturingAddit. Manuf.(2020)
ColtonT. et al.Influence of droplet velocity, spacing, and inter-arrival time on line formation and saturation in binder jet additive manufacturingAddit. Manuf.(2021)
InkleyC.G. et al.Impact of controlled prewetting on part formation in binder jet additive manufacturingAddit. Manuf.(2023)
ParteliE.J. et al.Particle-based simulation of powder application in additive manufacturingPowder Technol.(2016)
HaeriS. et al.Discrete element simulation and experimental study of powder spreading process in additive manufacturingPowder Technol.(2017)
MeierC. et al.Critical influences of particle size and adhesion on the powder layer uniformity in metal additive manufacturingJ. Mater Process. Technol.(2019)
HeY. et al.Combined effect of particle size and surface cohesiveness on powder spreadability for additive manufacturingPowder Technol.(2021)

Influences of the Powder Size and Process Parameters on the Quasi-Stability of Molten Pool Shape in Powder Bed Fusion-Laser Beam of Molybdenum

몰리브덴 분말층 융합-레이저 빔의 용융 풀 형태의 준안정성에 대한 분말 크기 및 공정 매개변수의 영향

Abstract

Formation of a quasi-steady molten pool is one of the necessary conditions for achieving excellent quality in many laser processes. The influences of distribution characteristics of powder sizes on quasi-stability of the molten pool shape during single-track powder bed fusion-laser beam (PBF-LB) of molybdenum and the underlying mechanism were investigated.

The feasibility of improving quasi-stability of the molten pool shape by increasing the laser energy conduction effect and preheating was explored. Results show that an increase in the range of powder sizes does not significantly influence the average laser energy conduction effect in PBF-LB process. Whereas, it intensifies fluctuations of the transient laser energy conduction effect.

It also leads to fluctuations of the replenishment rate of metals, difficulty in formation of the quasi-steady molten pool, and increased probability of incomplete fusion and pores defects. As the laser power rises, the laser energy conduction effect increases, which improves the quasi-stability of the molten pool shape. When increasing the laser scanning speed, the laser energy conduction effect grows.

However, because the molten pool size reduces due to the decreased heat input, the replenishment rate of metals of the molten pool fluctuates more obviously and the quasi-stability of the molten pool shape gets worse. On the whole, the laser energy conduction effect in the PBF-LB process of Mo is low (20-40%). The main factor that affects quasi-stability of the molten pool shape is the amount of energy input per unit length of the scanning path, rather than the laser energy conduction effect.

Moreover, substrate preheating can not only enlarge the molten pool size, particularly the length, but also reduce non-uniformity and discontinuity of surface morphologies of clad metals and inhibit incomplete fusion and pores defects.

준안정 용융 풀의 형성은 많은 레이저 공정에서 우수한 품질을 달성하는 데 필요한 조건 중 하나입니다. 몰리브덴의 단일 트랙 분말층 융합 레이저 빔(PBF-LB) 동안 용융 풀 형태의 준안정성에 대한 분말 크기 분포 특성의 영향과 그 기본 메커니즘을 조사했습니다.

레이저 에너지 전도 효과와 예열을 증가시켜 용융 풀 형태의 준안정성을 향상시키는 타당성을 조사했습니다. 결과는 분말 크기 범위의 증가가 PBF-LB 공정의 평균 레이저 에너지 전도 효과에 큰 영향을 미치지 않음을 보여줍니다. 반면, 과도 레이저 에너지 전도 효과의 변동이 강화됩니다.

이는 또한 금속 보충 속도의 변동, 준안정 용융 풀 형성의 어려움, 불완전 융합 및 기공 결함 가능성 증가로 이어집니다. 레이저 출력이 증가함에 따라 레이저 에너지 전도 효과가 증가하여 용융 풀 모양의 준 안정성이 향상됩니다. 레이저 스캐닝 속도를 높이면 레이저 에너지 전도 효과가 커집니다.

그러나 열 입력 감소로 인해 용융 풀 크기가 줄어들기 때문에 용융 풀의 금속 보충 속도의 변동이 더욱 뚜렷해지고 용융 풀 형태의 준안정성이 악화됩니다.

전체적으로 Mo의 PBF-LB 공정에서 레이저 에너지 전도 효과는 낮다(20~40%). 용융 풀 형상의 준안정성에 영향을 미치는 주요 요인은 레이저 에너지 전도 효과보다는 스캐닝 경로의 단위 길이당 입력되는 에너지의 양입니다.

또한 기판 예열은 용융 풀 크기, 특히 길이를 확대할 수 있을 뿐만 아니라 클래드 금속 표면 형태의 불균일성과 불연속성을 줄이고 불완전한 융합 및 기공 결함을 억제합니다.

Fig. 1View in article
Fig. 2View in article
Fig. 3View in article
Fig. 4View in article
Fig. 5View in article
Fig. 6View in article
Fig. 7View in article
Fig. 8View in article
Fig. 9View in article
Fig. 10View in article
Fig. 11View in article
Fig. 12View in article
Fig. 13View in article
Fig. 14View in article
Fig. 15View in article
Fig. 16View in article
Fig. 17View in article
Fig. 18View in article
Fig. 19View in article
Fig. 20View in article

References

M. Sharifitabar, F.O. Sadeq, and M.S. Afarani, Synthesis and Kinetic Study of Mo (Si, Al)2 Coatings on the Surface of Molybdenum Through Hot Dipping into a Commercial Al-12 wt.% Si Alloy Melt, Surf. Interfaces, 2021, 24, p 101044.Article CAS Google Scholar
Z. Zhang, X. Li, and H. Dong, Response of a Molybdenum Alloy to Plasma Nitriding, Int. J. Refract. Met. Hard Mater., 2018, 72, p 388–395.Article CAS Google Scholar
C. Tan, K. Zhou, M. Kuang, W. Ma, and T. Kuang, Microstructural Characterization and Properties of Selective Laser Melted Maraging Steel with Different Build Directions, Sci. Technol. Adv. Mater., 2018, 19(1), p 746–758.Article CAS Google Scholar
C. Tan, F. Weng, S. Sui, Y. Chew, and G. Bi, Progress and Perspectives in Laser Additive Manufacturing of Key Aeroengine Materials, Int. J. Mach. Tools Manuf, 2021, 170, p 103804.Article Google Scholar
S.A. Khairallah and A. Anderson, Mesoscopic Simulation Model of Selective Laser Melting of Stainless Steel Powder, J. Mater. Process. Technol., 2014, 214(11), p 2627–2636.Article CAS Google Scholar
S.A. Khairallah, A.T. Anderson, A. Rubenchik, and W.E. King, Laser Powder-Bed Fusion Additive Manufacturing: Physics of Complex Melt Flow and Formation Mechanisms of Pores, Spatter, and Denudation Zones, Acta Mater., 2016, 108, p 36–45.Article CAS ADS Google Scholar
K.Q. Le, C. Tang, and C.H. Wong, On the Study of Keyhole-Mode Melting in Selective Laser Melting Process, Int. J. Therm. Sci., 2019, 145, p 105992.Article Google Scholar
M. Bayat, A. Thanki, S. Mohanty, A. Witvrouw, S. Yang, J. Thorborg, N.S. Tiedje, and J.H. Hattel, Keyhole-Induced Porosities in Laser-Based Powder Bed Fusion (L-PBF) of Ti6Al4V: High-Fidelity Modelling and Experimental Validation, Addit. Manuf., 2019, 30, p 100835.CAS Google Scholar
B. Liu, G. Fang, L. Lei, and X. Yan, Predicting the Porosity Defects in Selective Laser Melting (SLM) by Molten Pool Geometry, Int. J. Mech. Sci., 2022, 228, p 107478.Article Google Scholar
W. Ge, J.Y.H. Fuh, and S.J. Na, Numerical Modelling of Keyhole Formation in Selective Laser Melting of Ti6Al4V, J. Manuf. Process., 2021, 62, p 646–654.Article Google Scholar
W. Ge, S. Han, S.J. Na, and J.Y.H. Fuh, Numerical Modelling of Surface Morphology in Selective Laser Melting, Comput. Mater. Sci., 2021, 186, p 110062.Article Google Scholar
Y.-C. Wu, C.-H. San, C.-H. Chang, H.-J. Lin, R. Marwan, S. Baba, and W.-S. Hwang, Numerical Modeling of Melt-Pool Behavior In Selective Laser Melting with Random Powder Distribution and Experimental Validation, J. Mater. Process. Technol., 2018, 254, p 72–78.Article Google Scholar
C. Tang, J.L. Tan, and C.H. Wong, A Numerical Investigation on the Physical Mechanisms of Single Track Defects in Selective Laser Melting, Int. J. Heat Mass Transf., 2018, 126, p 957–968.Article CAS Google Scholar
X. Zhou, X. Liu, D. Zhang, Z. Shen, and W. Liu, Balling Phenomena in Selective Laser Melted Tungsten, J. Mater. Process. Technol., 2015, 222, p 33–42.Article CAS Google Scholar
J.D.K. Monroy and J. Ciurana, Study of the Pore Formation on CoCrMo Alloys by Selective Laser Melting Manufacturing Process, Procedia Eng., 2013, 63, p 361–369.Article CAS Google Scholar
L. Kaserer, J. Braun, J. Stajkovic, K.H. Leitz, B. Tabernig, P. Singer, I. Letofsky-Papst, H. Kestler, and G. Leichtfried, Fully Dense and Crack Free Molybdenum Manufactured by Selective Laser Melting Through Alloying with Carbon, Int. J. Refract. Met. Hard Mater., 2019, 84, p 105000.Article CAS Google Scholar
T.B.T. Majumdar, E.M.C. Ribeiro, J.E. Frith, and N. Birbilis, Understanding the Effects of PBF Process Parameter Interplay on Ti-6Al-4V Surface Properties, PLoS ONE, 2019, 14, p e0221198.Article CAS PubMed PubMed Central Google Scholar
A.K.J.-R. Poulin, P. Terriault, and V. Brailovski, Long Fatigue Crack Propagation Behavior of Laser Powder Bed-Fused Inconel 625 with Intentionally- Seeded Porosity, Int. J. Fatigue, 2019, 127, p 144–156.Article CAS Google Scholar
P. Rebesan, M. Ballan, M. Bonesso, A. Campagnolo, S. Corradetti, R. Dima, C. Gennari, G.A. Longo, S. Mancin, M. Manzolaro, G. Meneghetti, A. Pepato, E. Visconti, and M. Vedani, Pure Molybdenum Manufactured by Laser Powder Bed Fusion: Thermal and Mechanical Characterization at Room and High Temperature, Addit. Manuf., 2021, 47, p 102277.CAS Google Scholar
D. Wang, C. Yu, J. Ma, W. Liu, and Z. Shen, Densification and Crack Suppression in Selective Laser Melting of Pure Molybdenum, Mater. Des., 2017, 129, p 44–52.Article CAS Google Scholar
K.-H. Leitz, P. Singer, A. Plankensteiner, B. Tabernig, H. Kestler, and L.S. Sigl, Multi-physical Simulation of Selective Laser Melting, Met. Powder Rep., 2017, 72, p 331–338.Article Google Scholar
D.G.J. Zhang, Y. Yang, H. Zhang, H. Chen, D. Dai, and K. Lin, Influence of Particle Size on Laser Absorption and Scanning Track Formation Mechanisms of Pure Tungsten Powder During Selective Laser Melting, Engineering, 2019, 5, p 736–745.Article CAS Google Scholar
L. Caprio, A.G. Demir, and B. Previtali, Influence of Pulsed and Continuous Wave Emission on Melting Efficiency in Selective Laser Melting, J. Mater. Process. Technol., 2019, 266, p 429–441.Article CAS Google Scholar
D. Gu, M. Xia, and D. Dai, On the Role of Powder Flow Behavior in Fluid Thermodynamics and Laser Processability of Ni-based Composites by Selective Laser Melting, Int. J. Mach. Tools Manuf, 2018, 137, p 67–78.Article Google Scholar
W.-I. Cho, S.-J. Na, C. Thomy, and F. Vollertsen, Numerical Simulation of Molten Pool Dynamics in High Power Disk Laser Welding, J. Mater. Process. Technol., 2012, 212(1), p 262–275.Article CAS Google Scholar
S.W. Han, J. Ahn, and S.J. Na, A Study on Ray Tracing Method for CFD Simulations of Laser Keyhole Welding: Progressive Search Method, Weld. World, 2016, 60, p 247–258.Article CAS Google Scholar
W. Ge, S. Han, Y. Fang, J. Cheon, and S.J. Na, Mechanism of Surface Morphology in Electron Beam Melting of Ti6Al4V Based on Computational Flow Patterns, Appl. Surf. Sci., 2017, 419, p 150–158.Article CAS ADS Google Scholar
W.-I. Cho, S.-J. Na, C. Thomy, and F. Vollertsen, Numerical Simulation of Molten Pool Dynamics in High Power Disk Laser Welding, J. Mater. Process. Technol., 2012, 212, p 262–275.Article CAS Google Scholar
W. Ma, J. Ning, L.-J. Zhang, and S.-J. Na, Regulation of Microstructures and Properties of Molybdenum-Silicon-Boron Alloy Subjected to Selective Laser Melting, J. Manuf. Process., 2021, 69, p 593–601.Article Google Scholar
S. Haeri, Y. Wang, O. Ghita, and J. Sun, Discrete Element Simulation and Experimental Study of Powder Spreading Process in Additive Manufacturing, Powder Technol., 2016, 306, p 45–54.Article Google Scholar
D. Yao, X. Liu, J. Wang, W. Fan, M. Li, H. Fu, H. Zhang, X. Yang, Q. Zou, and X. An, Numerical Insights on the Spreading of Practical 316 L Stainless Steel Powder in SLM Additive Manufacturing, Powder Technol., 2021, 390, p 197–208.Article CAS Google Scholar
S. Vock, B. Klöden, A. Kirchner, T. Weißgärber, and B. Kieback, Powders for Powder Bed Fusion: A Review, Prog. Addit. Manuf., 2019, 4, p 383–397.Article Google Scholar
X. Luo, C. Yang, Z.Q. Fu, L.H. Liu, H.Z. Lu, H.W. Ma, Z. Wang, D.D. Li, L.C. Zhang, and Y.Y. Li, Achieving Ultrahigh-Strength in Beta-Type Titanium Alloy by Controlling the Melt Pool Mode in Selective Laser Melting, Mater. Sci. Eng. A, 2021, 823, p 141731.Article CAS Google Scholar
J. Braun, L. Kaserer, J. Stajkovic, K.-H. Leitz, B. Tabernig, P. Singer, P. Leibenguth, C. Gspan, H. Kestler, and G. Leichtfried, Molybdenum and Tungsten Manufactured by Selective Laser Melting: Analysis of Defect Structure and Solidification Mechanisms, Int. J. Refract. Met. Hard Mater., 2019, 84, p 104999.Article CAS Google Scholar
L. Kaserera, J. Brauna, J. Stajkovica, K.-H. Leitzb, B. Tabernigb, P. Singerb, I. Letofsky-Papstc, H. Kestlerb, and G. Leichtfried, Fully Dense and Crack Free Molybdenum Manufactured by Selective Laser Melting Through Alloying with Carbon, Int. J. Refract Metal Hard Mater., 2019, 84, p 105000.Article Google Scholar

The impacts of profile concavity on turbidite deposits: Insights from the submarine canyons on global continental margins

프로필 오목부가 탁도 퇴적물에 미치는 영향: 전 세계 대륙 경계에 대한 해저 협곡의 통찰력

Kaiqi Yu ^a, Elda Miramontes ^bc, Matthieu J.B. Cartigny ^d, Yuping Yang ^a, Jingping Xu ^a
^aDepartment of Ocean Science and Engineering, Southern University of Science and Technology, 1088 Xueyuan Rd., Shenzhen 518055, Guangdong, China
^bMARUM-Center for Marine Environmental Sciences, University of Bremen, Bremen, Germany^c
Faculty of Geosciences, University of Bremen, Bremen, Germany
^dDepartment of Geography, Durham University, South Road, Durham DH1 3LE, UK

Received 10 August 2023, Revised 13 March 2024, Accepted 13 March 2024, Available online 17 March 2024, Version of Record 20 March 2024.

What do these dates mean?Show lessAdd to MendeleyShareCite

https://doi.org/10.1016/j.geomorph.2024.109157 Get rights and content

Highlights

•The impact of submarine canyon concavity on turbidite deposition was assessed.
•Distribution of turbidite deposits varies with changes in canyon concavity.
•Three distinct deposition patterns were identified.
•The recognized deposition patterns align well with the observed turbidite deposits.

Abstract

Submarine canyons are primary conduits for turbidity currents transporting terrestrial sediments, nutrients, pollutants and organic carbon to the deep sea. The concavity in the longitudinal profile of these canyons (i.e. the downstream flattening rate along the profiles) influences the transport processes and results in variations in turbidite thickness, impacting the transfer and burial of particles. To better understand the controlling mechanisms of canyon concavity on the distribution of turbidite deposits, here we investigate the variation in sediment accumulation as a function of canyon concavity of 20 different modern submarine canyons, distributed on global continental margins. In order to effectively assess the isolated impact of the concavity of 20 different canyons, a series of two-dimensional, depth-resolved numerical simulations are conducted. Simulation results show that the highly concave profile (e.g. Surveyor and Horizon) tends to concentrate the turbidite deposits mainly at the slope break, while nearly straight profiles (e.g. Amazon and Congo) result in deposition focused at the canyon head. Moderately concave profiles with a smoother canyon floor (e.g. Norfolk-Washington and Mukluk) effectively facilitate the downstream transport of suspended sediments in turbidity currents. Furthermore, smooth and steep upper reaches of canyons commonly contribute to sediment bypass (i.e. Mukluk and Chirikof), while low slope angles lead to deposition at upper reaches (i.e. Bounty and Valencia). At lower reaches, the distribution of turbidite deposits is consistent with the occurrence of hydraulic jumps. Under the influence of different canyon concavities, three types of deposition patterns are inferred in this study, and verified by comparison with observed turbidite deposits on the modern or paleo-canyon floor. This study demonstrates a potential difference in sediment transport efficiency of submarine canyons with different concavities, which has potential consequences for sediment and organic carbon transport through submarine canyons.

Introduction

Submarine canyons are pivotal links in source-to-sink systems on continental margins (Sømme et al., 2009; Nyberg et al., 2018; Pope et al., 2022a, Pope et al., 2022b) that provide efficient pathways for moving prodigious volumes of terrestrial materials to the abyssal basin (Spychala et al., 2020; Heijnen et al., 2022). When turbidity currents, the main force that transports the above mentioned sediments (Xu et al., 2004; Xu, 2010; Talling et al., 2013; Stevenson et al., 2015), slow down after entering a flatter and/or wider stretch of the canyon downstream, the laden sediments settle, often rapidly, to form a deposit called turbidite that is known for organic carbon burial, hydrocarbon reserves and the accumulation of microplastics (Galy et al., 2007; Pohl et al., 2020a; Pope et al., 2022b; Pierdomenico et al., 2023). A set of flume experiments by Pohl et al. (2020b) revealed that the variation of bed slope plays a dominant role in controlling the sizes and locations of the deposit: a) a more gently dipping upper slope leads to upstream migration of upslope pinch-out; b) the increase of lower slope results in a decrease of the deposit thickness (Fig. 1a).

From upper continental slopes to deepwater basins, turbidity currents are commonly confined by submarine canyons that facilitate the longer distance transport of sediments (Eggenhuisen et al., 2022; Pope et al., 2022a; Wahab et al., 2022, Li et al., 2023a). The concavity, defined here as the downstream flattening rate of profiles (Covault et al., 2011; Chen et al., 2019; Seybold et al., 2021; Soutter et al., 2021a), of the longitudinal bed profile of the submarine canyons is therefore a key factor that determines hydrodynamic processes of turbidity currents, including the accumulation of sediments along the canyon thalweg (Covault et al., 2014; de Leeuw et al., 2016; Heerema et al., 2022; Heijnen et al., 2022). Due to the comprehensive impacts of sediment supply, grain size, climate change, regional tectonics, associated river and self-incision, the concavity of submarine canyons on global continental margins varies greatly (Parker et al., 1986; Harris and Whiteway, 2011; Casalbore et al., 2018; Nyberg et al., 2018; Soutter et al., 2021a, Li et al., 2023b), which is much more complex than the two constant slope setup of Pohl et al. (2020b)’s flume experiment (Fig. 1a). This raises the question of how the more complex concavity influences the dynamics of turbidity currents and the resultant distribution of turbidite deposits. For instance, the longitudinal profile concavity can also be increased by steepening the upper slope and/or gentling the lower slope of canyons (Fig. 1b). Parameters, known as significant factors influencing flow dynamics, include dip angle (Pohl et al., 2019), bed roughness (Baghalian and Ghodsian, 2020), obstacle presence (Howlett et al., 2019), and confinement conditions (Soutter et al., 2021b). However, the role of channel concavity in determining the downstream evolution of flow dynamics remains poorly understood (Covault et al., 2011; Georgiopoulou and Cartwright, 2013), and it is still unclear whether changes in concavity can result in different locations of pinch-out points and variations in turbidite deposit thicknesses (Pohl et al., 2020b).

In this study, we hypothesize that a more concave profile resulting from a steeper upper slope and a gentler lower slope may lead to a downstream migration of the upslope pinch-out and an increase of deposit thickness (Fig. 1b). This hypothesis is tested in 20 modern submarine canyons (shown in Fig. 2) whose longitudinal profiles are extracted from the GEBCO_2022 grid. Due to the lack of data describing the turbidite thickness trends in these canyons, we used a numerical model (FLOW-3D® software) to simulate the depositional process. The simulation results allow us to address at least two questions: (1) How does the concavity affect the distribution and thickness of turbidite deposits along the canyon thalwegs? (2) What is the impact of canyon concavity on the dynamics of the turbidity currents? Such answers on a global scale are undoubtedly helpful in understanding not only the sediment transport processes but also the efficient transfer and burial of organic carbon along global continental margins.

Section snippets

Submarine canyons used in this study

The longitudinal profiles of 20 modern submarine canyons are obtained using Global Mapper® from a public domain database GEBCO_2022 (doi:https://doi.org/10.5285/e0f0bb80-ab44-2739-e053-6c86abc0289c). The GEBCO_2022 grid provides elevation data, in meters, on a 15 arc-second interval grid. The 20 selected submarine canyons, which span the typical distance covered by turbidity currents, have been chosen from a diverse range of submarine canyon and channel systems that extend at least 250 km

Concavity of longitudinal canyon profiles

The NCI and α values of all 20 canyon profiles utilized in this study are plotted in Fig. 4, indicating the majority of these submarine canyons typically exhibit a concave profile, characterized by a negative NCI, except for the Amazon. In most of the profiles, the NCI is lower than −0.08, with the most concave point (indicated by the minimum ratio α) located closer to the canyon head than to the profile end, and their upper reaches are steeper than lower reaches, typically observed as the

Validation of the hypothesis

As previously mentioned in this paper, one of the primary objectives of this study is to evaluate the hypothesis inferred from the flume tank experiment of Pohl et al. (2020b): whether a more concave canyon profile can exert a comparable influence on turbidite deposits as the steepness of the lower and upper slopes in a slope-break system (Fig. 1). Shown as the modeling results, the deposition pattern of this study is more ‘irregular’ compared with the flume tank experiment (Pohl et al., 2020b

Conclusion

Based on global bathymetry, this study simulates the depositional behavior of turbidity currents flowing through the 20 different submarine canyons on the margins of open ocean and marginal sea. Influenced by the different concavities, the resulted deposition patterns are characterized by a variable distribution of turbidite deposits.

1)The simulation results demonstrate that the accumulation of turbidite deposits is primarily observed in downstream regions near the slope break for highly concave

CRediT authorship contribution statement

Kaiqi Yu: Writing – review & editing, Writing – original draft, Validation, Software, Methodology, Investigation, Conceptualization. Elda Miramontes: Writing – review & editing, Supervision, Conceptualization. Matthieu J.B. Cartigny: Writing – review & editing, Supervision. Yuping Yang: Software, Methodology. Jingping Xu: Writing – review & editing, Supervision, Funding acquisition, Conceptualization.

Declaration of competing interest

The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper.

Acknowledgements

This study is supported by the Shenzhen Natural Science Foundation (JCYJ20210324105211031). Matthieu J. B. Cartigny was supported by Royal Society Research Fellowship (DHF/R1/180166). We thank the Chief Editor Zhongyuan Chen, the associate editor and two reviewers for their constructive comments that helped us improve our manuscript.

References (70)

S. Baghalian et al.Experimental study on the effects of artificial bed roughness on turbidity currents over abrupt bed slope changeInt. J. Sediment Res.(2020)
D.S. Brothers et al.Geomorphic characterization of the U.S. Atlantic continental marginMar. Geol.(2013)
D. Casalbore et al.Characterization of overbanking features on the lower reach of the Gioia-Mesima canyon-channel system (southern Tyrrhenian Sea) through integration of morpho-stratigraphic data and physical modellingProg. Oceanogr.(2018)
A. Festa et al.Does subduction of mass transport deposits (MTDs) control seismic behavior of shallow–level megathrusts at convergent margins?Gondwana Res.(2018)
A. Georgiopoulou et al.A critical test of the concept of submarine equilibrium profileMar. Pet. Geol.(2013)
P.T. Harris et al.Global distribution of large submarine canyons: Geomorphic differences between active and passive continental marginsMar. Geol.(2011)
M.S. Heijnen et al.Fill, flush or shuffle: how is sediment carried through submarine channels to build lobes?Earth Planet. Sci. Lett.(2022)
S. Li et al.Submarine canyon morphology along the Chilean marine forearc (19°S–45°S)Geomorphology(2023)
W. Li et al.Initiation and evolution of an isolated submarine canyon system on a low-gradient continental slopeGeomorphology(2023)
B. Nyberg et al.Revisiting morphological relationships of modern source-to-sink segments as a first-order approach to scale ancient sedimentary systemsSediment. Geol.(2018)
C. Pirmez et al.Reconstruction of turbidity currents in Amazon ChannelMar. Pet. Geol.(2003)
P.J. Talling et al.How are subaqueous sediment density flows triggered, what is their internal structure and how does it evolve? Direct observations from monitoring of active flowsEarth Sci. Rev.(2013)
M. Azpiroz-Zabala et al.Newly recognized turbidity current structure can explain prolonged flushing of submarine canyonsSci. Adv.(2017)
N. Babonneau et al.Sedimentary Architecture in Meanders of a Submarine Channel: Detailed Study of the Present Congo Turbidite Channel (Zaiango Project)J. Sediment. Res.(2010)
R. Basani et al.MassFLOW-3DTM as a simulation tool for turbidity currents: some preliminary results
H.L. Brooks et al.Disconnected submarine lobes as a record of stepped slope evolution over multiple sea-level cyclesGeosphere(2018)
S.A. Chen et al.Aridity is expressed in river topography globallyNature(2019)
J.A. Covault et al.The natural range of submarine canyon-and-channel longitudinal profilesGeosphere(2011)
J.A. Covault et al.Deep-water channel run-out length: insights from seafloor geomorphologyJ. Sediment. Res.(2012)
J.A. Covault et al.Submarine channel initiation, filling and maintenance from sea-floor geomorphology and morphodynamic modelling of cyclic stepsSedimentology(2014)
J. de Leeuw et al.Morphodynamics of submarine channel inception revealed by new experimental approachNat. Commun.(2016)
J. de Leeuw et al.Entrainment and suspension of sand and gravelEarth Surf. Dyn.(2020)
J.T. Eggenhuisen et al.The Sediment Budget Estimator (SBE): a process model for the stochastic estimation of fluxes and budgets of sediment through submarine channel systemsJ. Sediment. Res.(2022)
T.H. Ellison et al.Turbulent entrainment in stratified flowsJ. Fluid Mech.(1959)
R.I. Ferguson et al.A simple universal equation for grain settling velocityJ. Sediment. Res.(2004)
A.M. Fernandes et al.Flow substrate interactions in aggrading and degrading submarine channelsJ. Sediment. Res.(2020)
Flow ScienceFLOW-3D User Manual v11. 2(2018)
V. Galy et al.Efficient organic carbon burial in the Bengal fan sustained by the Himalayan erosional systemNature(2007)
Z. Ge et al.How is a turbidite actually deposited?Sci. Adv.(2022)
B. Gomez et al.An assessment of bed load sediment transport formulae for gravel bed riversWater Resour. Res.(1989)
W.H. Graf et al.Suspension flows in open channels; experimental studyJ. Hydraul. Res.(2010)
C.J. Heerema et al.How distinctive are flood-triggered turbidity currents?J. Sediment. Res.(2022)
D.M. Howlett et al.Response of unconfined turbidity current to deep-water fold and thrust belt topography: orthogonal incidence on solitary and segmented foldsSedimentology(2019)
S. Kim et al.Seismostratigraphic and geomorphic evidence for the glacial history of the Northwestern Chukchi Margin, Arctic OceanJ. Geophys. Res. Earth Surf.(2021)
M. Liu et al.Two distinct types of turbidity currents observed in the Manila Trench, South China SeaCommun. Earth Environ.(2023)

There are more references available in the full text version of this article.

Fig. 3. Free surface and substrate profiles in all Sp and Ls cases at t = 1 s, t = 3 s, and t = 5 s, arranged left to right (note: the colour contours correspond to the horizontal component of the flow velocity (u), expressed in m/s).

Numerical investigation of dam break flow over erodible beds with diverse substrate level variations

다양한 기질 수준 변화를 갖는 침식성 층 위의 댐 파손 흐름에 대한 수치 조사

Alireza Khoshkonesh¹, Blaise Nsom², Saeid Okhravi³*, Fariba Ahmadi Dehrashid⁴, Payam Heidarian⁵,
Silvia DiFrancesco⁶
¹Department of Geography, School of Social Sciences, History, and Philosophy, Birkbeck University of London, London, UK.
² Université de Bretagne Occidentale. IRDL/UBO UMR CNRS 6027. Rue de Kergoat, 29285 Brest, France.
³ Institute of Hydrology, Slovak Academy of Sciences, Dúbravská cesta 9, 84104, Bratislava, Slovak Republic.
⁴Department of Water Science and Engineering, Faculty of Agriculture, Bu-Ali Sina University, 65178-38695, Hamedan, Iran.
⁵Department of Civil, Environmental, Architectural Engineering and Mathematics, University of Brescia, 25123 Brescia, Italy.
⁶Niccol`o Cusano University, via Don C. Gnocchi 3, 00166 Rome, Italy. * Corresponding author. Tel.: +421-944624921. E-mail: saeid.okhravi@savba.sk

Abstract

This study aimed to comprehensively investigate the influence of substrate level difference and material composition on dam break wave evolution over two different erodible beds. Utilizing the Volume of Fluid (VOF) method, we tracked free surface advection and reproduced wave evolution using experimental data from the literature. For model validation, a comprehensive sensitivity analysis encompassed mesh resolution, turbulence simulation methods, and bed load transport equations. The implementation of Large Eddy Simulation (LES), non-equilibrium sediment flux, and van Rijn’s (1984) bed load formula yielded higher accuracy compared to alternative approaches. The findings emphasize the significant effect of substrate level difference and material composition on dam break morphodynamic characteristics. Decreasing substrate level disparity led to reduced flow velocity, wavefront progression, free surface height, substrate erosion, and other pertinent parameters. Initial air entrapment proved substantial at the wavefront, illustrating pronounced air-water interaction along the bottom interface. The Shields parameter experienced a one-third reduction as substrate level difference quadrupled, with the highest near-bed concentration observed at the wavefront. This research provides fresh insights into the complex interplay of factors governing dam break wave propagation and morphological changes, advancing our comprehension of this intricate phenomenon.

이 연구는 두 개의 서로 다른 침식층에 대한 댐 파괴파 진화에 대한 기질 수준 차이와 재료 구성의 영향을 종합적으로 조사하는 것을 목표로 했습니다. VOF(유체량) 방법을 활용하여 자유 표면 이류를 추적하고 문헌의 실험 데이터를 사용하여 파동 진화를 재현했습니다.

모델 검증을 위해 메쉬 해상도, 난류 시뮬레이션 방법 및 침대 하중 전달 방정식을 포함하는 포괄적인 민감도 분석을 수행했습니다. LES(Large Eddy Simulation), 비평형 퇴적물 플럭스 및 van Rijn(1984)의 하상 부하 공식의 구현은 대체 접근 방식에 비해 더 높은 정확도를 산출했습니다.

연구 결과는 댐 붕괴 형태역학적 특성에 대한 기질 수준 차이와 재료 구성의 중요한 영향을 강조합니다. 기판 수준 차이가 감소하면 유속, 파면 진행, 자유 표면 높이, 기판 침식 및 기타 관련 매개변수가 감소했습니다.

초기 공기 포집은 파면에서 상당한 것으로 입증되었으며, 이는 바닥 경계면을 따라 뚜렷한 공기-물 상호 작용을 보여줍니다. 기판 레벨 차이가 4배로 증가함에 따라 Shields 매개변수는 1/3로 감소했으며, 파면에서 가장 높은 베드 근처 농도가 관찰되었습니다.

이 연구는 댐 파괴파 전파와 형태학적 변화를 지배하는 요인들의 복잡한 상호 작용에 대한 새로운 통찰력을 제공하여 이 복잡한 현상에 대한 이해를 향상시킵니다.

Keywords

Dam break; Substrate level difference; Erodible bed; Sediment transport; Computational fluid dynamics CFD.

PDF Download

REFERENCES

Aleixo, R., Soares-Frazão, S., Zech, Y., 2010. Velocity profiles in
dam-break flows: water and sediment layers. In: Proc. Int. Conf.
on Fluvial Hydraulics “River Flow 2010”, pp. 533–540.
An, S., Ku, H., Julien, P.Y., 2015. Numerical modelling of local
scour caused by submerged jets. Maejo Int. J. Sci. Technol., 9, 3,
328–343.
Bahmanpouri, F., Daliri, M., Khoshkonesh, A., Namin, M.M.,
Buccino, M., 2021. Bed compaction effect on dam break flow over
erodible bed; experimental and numerical modeling. J. Hydrol.,
594, 125645. https://doi.org/10.1016/j.jhydrol.2020.125645
Baklanov, A., 2007. Environmental risk and assessment modelling
– scientific needs and expected advancements. In: Ebel, A.,
Davitashvili, T. (Eds.): Air, Water and Soil Quality Modelling
for Risk and Impact Assessment Springer, Dordrecht, pp. 29–44.
Biscarini, C., Di Francesco, S., Nardi, F., Manciola, P., 2013.
Detailed simulation of complex hydraulic problems with
macroscopic and mesoscopic mathematical methods. Math.
Probl. Eng., 928309. https://doi.org/10.1155/2013/928309
Cao, Z., Pender, G., Wallis, S., Carling, P., 2004. Computational
dam-break hydraulics over erodible sediment bed. J. Hydraul.
Eng., 130, 7, 689–703.
Catucci, D., Briganti, R., Heller, V., 2021. Numerical validation of novel
scaling laws for air entrainment in water. Proc. R. Soc. A, 477, 2255,20210339. https://doi.org/10.1098/rspa.2021.0339
Dehrashid, F.A., Heidari, M., Rahimi, H., Khoshkonesh, A., Yuan,
S., Tang, X., Lu, C., Wang, X., 2023. CFD modeling the flow
dynamics in an open channel with double-layered vegetation.
Model. Earth Syst. Environ., 9, 1, 543–555.
Desombre, J., Morichon, D., Mory, M., 2013. RANS v2-f simulation
of a swash event: Detailed flow structure. Coastal Eng., 71, 1–12.
Dodangeh, E., Afzalimehr, H., 2022. Incipient motion of sediment
particles in the presence of bed forms under decelerating and
accelerating flows. J. Hydrol. Hydromech., 70, 1, 89–102.
Dong, Z., Wang, J., Vetsch, D.F., Boes, R.M., Tan, G., 2019.
Numerical simulation of air entrainment on stepped
spillways. In: E-proceedings of the 38th IAHR World Congress
(pp. 1494). September 1–6, 2019, Panama City, Panama. DOI:
10.3850/38WC092019-0755
Flow3D [computer software]. 2023. Santa Fe, NM: Flow Science,
Inc.
Fraccarollo, L., Capart, H., 2002. Riemann wave description of
erosional dam-break flows. J. Fluid Mech., 461, 183–228.
Gu, Z., Wang, T., Meng, W., Yu, C.H., An, R., 2023. Numerical
investigation of silted-up dam-break flow with different silted-up
sediment heights. Water Supply, 23, 2, 599–614.
Gualtieri, P., De Felice, S., Pasquino, V., Doria, G.P., 2018. Use of
conventional flow resistance equations and a model for the
Nikuradse roughness in vegetated flows at high submergence. J.
Hydrol. Hydromech., 66, 1, 107–120.
Heller, V., 2011. Scale effects in physical hydraulic engineering
models. J. Hydraul. Res., 49, 3, 293–306.
Hirt, C.W., 2003. Modeling turbulent entrainment of air at a free
surface. Flow Science, Inc.
Hirt, C.W., Nichols, B.D., 1981. Volume of fluid (VOF) method for
the dynamics of free boundaries. J. Comput. Phys., 39, 1, 201–
225.
Issakhov, A., Zhandaulet, Y., Nogaeva, A., 2018. Numerical
simulation of dam break flow for various forms of the obstacle
by VOF method. Int. J. Multiphase Flow, 109, 191–206.
Khayyer, A., Gotoh, H., 2010. On particle-based simulation of a dam
break over a wet bed. J. Hydraul. Res., 48, 2, 238–249.
Khoshkonesh, A., Daliri, M., Riaz, K., Dehrashid, F.A.,
Bahmanpouri, F., Di Francesco, S., 2022. Dam-break flow
dynamics over a stepped channel with vegetation. J. Hydrol., 613,128395. https://doi.org/10.1016/j.jhydrol.2022.128395
Khoshkonesh, A., Nsom, B., Gohari, S., Banejad, H., 2019.
A comprehensive study on dam-break flow over dry and wet
beds. Ocean Eng., 188, 106279.
https://doi.org/10.1016/j.oceaneng.2019.106279
Khoshkonesh, A., Sadeghi, S.H., Gohari, S., Karimpour, S., Oodi,
S., Di Francesco, S., 2023. Study of dam-break flow over a
vegetated channel with and without a drop. Water Resour.
Manage., 37, 5, 2107–2123.
Khosravi, K., Chegini, A.H.N., Cooper, J., Mao, L., Habibnejad, M.,
Shahedi, K., Binns, A., 2021. A laboratory investigation of bedload transport of gravel sediments under dam break flow. Int. J.
Sediment Res., 36, 2, 229–234.
Kim, Y., Zhou, Z., Hsu, T.J., Puleo, J.A., 2017. Large eddy
simulation of dam‐break‐driven swash on a rough‐planar beach.
J. Geophys. Res.: Oceans, 122, 2, 1274–1296.
Kocaman, S., Ozmen-Cagatay, H., 2012. The effect of lateral
channel contraction on dam break flows: Laboratory experiment.
J. Hydrol., 432, 145–153.
Leal, J.G., Ferreira, R.M., Cardoso, A.H., 2006. Dam-break wavefront celerity. J. Hydraul. Eng., 132, 1, 69–76.
Leal, J.G.A.B., Ferreira, R.M., Cardoso, A.H., 2003. Dam-break
wave propagation over a cohesionless erodible bed. In: Proc.
30rd IAHR Congress, 100, 261–268.
Li, Y. L., Ma, Y., Deng, R., Jiang, D.P., Hu, Z., 2019. Research on
dam-break induced tsunami bore acting on the triangular
breakwater based on high order 3D CLSVOF-THINC/WLICIBM approaching. Ocean Eng., 182, 645–659.
Li, Y.L., Yu, C.H., 2019. Research on dam-break flow induced front
wave impacting a vertical wall based on the CLSVOF and level
set methods. Ocean Eng., 178, 442–462.
Mei, S., Chen, S., Zhong, Q., Shan, Y., 2022. Detailed numerical
modeling for breach hydrograph and morphology evolution
during landslide dam breaching. Landslides, 19, 12, 2925–2949.
Meng, W., Yu, C.H., Li, J., An, R., 2022. Three-dimensional simulation
of silted-up dam-break flow striking a rigid structure. Ocean Eng.,
261, 112042. https://doi.org/10.1016/j.oceaneng.2022.112042
Meyer-Peter, E., Müller, R., 1948. Formulas for bed-load transport.
In: IAHSR 2nd meeting, Stockholm, appendix 2. IAHR.
Nielsen, P., 1984. Field measurements of time-averaged suspended
sediment concentrations under waves. Coastal Eng., 8, 1, 51–72.
Nielsen, P., 2018. Bed shear stress, surface shape and velocity field
near the tips of dam-breaks, tsunami and wave runup. Coastal
Eng., 138, 126–131.
Nsom, B., Latrache, N., Ramifidisoa, L., Khoshkonesh, A., 2019.
Analytical solution to the stability of gravity-driven stratified
flow of two liquids over an inclined plane. In: 24th French
Mechanics Congress in Brest. Brest, p. 244178.
Nsom, B., Ravelo, B., Ndong, W., 2008. Flow regimes in horizontal
viscous dam-break flow of Cayous mud. Appl. Rheol., 18, 4,
43577-1. https://doi.org/10.1515/arh-2008-0012
Oguzhan, S., Aksoy, A.O., 2020. Experimental investigation of the
effect of vegetation on dam break flood waves. J. Hydrol.
Hydromech., 68, 3, 231–241.
Okhravi, S., Gohari, S., Alemi, M., Maia, R., 2022. Effects of bedmaterial gradation on clear water scour at single and group of
piles. J. Hydrol. Hydromech., 70, 1, 114–127.
Okhravi, S., Gohari, S., Alemi, M., Maia, R., 2023. Numerical
modeling of local scour of non-uniform graded sediment for two
arrangements of pile groups. Int. J. Sediment Res., 38, 4, 597–614.
Parambath, A., 2010. Impact of tsunamis on near shore wind power
units. Master’s Thesis. Texas A&M University. Available
electronically from https://hdl.handle.net/1969.1/ETD-TAMU2010-12-8919
Pintado-Patiño, J.C., Puleo, J.A., Krafft, D., Torres-Freyermuth, A.,

Hydrodynamics and sediment transport under a dambreak-driven swash: An experimental study. Coastal Eng., 170,
https://doi.org/10.1016/j.coastaleng.2021.103986
Riaz, K., Aslam, H.M.S., Yaseen, M.W., Ahmad, H.H.,
Khoshkonesh, A., Noshin, S., 2022. Flood frequency analysis
and hydraulic design of bridge at Mashan on river Kunhar. Arch.
Hydroengineering Environ. Mech., 69, 1, 1–12.
Ritter, A., 1892. Die Fortpflanzung der Wasserwellen. Zeitschrift
des Vereines Deutscher Ingenieure, 36, 33, 947–954. (In
German.)
Smagorinsky, J., 1963. General circulation experiments with the
primitive equations: I. The basic experiment. Mon. Weather
Rev., 91, 3, 99–164.
Soulsby, R.L., 1997. Dynamics of marine sands: a manual for
practical applications. Oceanogr. Lit. Rev., 9, 44, 947.
Spinewine, B., Capart, H., 2013. Intense bed-load due to a sudden
dam-break. J. Fluid Mech., 731, 579–614.
Van Rijn, L.C., 1984. Sediment transport, part I: bed load transport.
J. Hydraul. Eng., 110, 10, 1431–1456.
Vosoughi, F., Rakhshandehroo, G., Nikoo, M.R., Sadegh, M.,
Experimental study and numerical verification of
silted-up dam break. J. Hydrol., 590, 125267.
https://doi.org/10.1016/j.jhydrol.2020.125267
Wu, W., Wang, S.S., 2008. One-dimensional explicit finite-volume
model for sediment transport. J. Hydraul. Res., 46, 1, 87–98.
Xu, T., Huai, W., Liu, H., 2023. MPS-based simulation of
dam-break wave propagation over wet beds with a
sediment layer. Ocean Eng., 281, 115035.
https://doi.org/10.1016/j.oceaneng.2023.115035
Yang, S., Yang, W., Qin, S., Li, Q., Yang, B., 2018. Numerical study
on characteristics of dam-break wave. Ocean Eng., 159, 358–371.
Yao, G.F., 2004. Development of new pressure-velocity solvers in
FLOW-3D. Flow Science, Inc., USA.

PDF Download

Figure 1. Experimental setup and materials. (a) Schematic of the DED process, where three types of base materials were adopted—B1 (IN718), B2 (IN625), and B3 (SS316L), and two types of powder materials were adopted—P1 (IN718) and P2 (SS316L). (b) In situ high-speed imaging of powder flow and the SEM images of IN718 and SS316L powder particle. (c) Powder size statistics, and (d) element composition of powder IN718 (P1) and SS316L (P2).

Printability disparities in heterogeneous materialcombinations via laser directed energy deposition:a comparative stud

Jinsheng Ning1,6, Lida Zhu1,6,∗, Shuhao Wang2, Zhichao Yang1, Peihua Xu1,Pengsheng Xue3, Hao Lu1, Miao Yu1, Yunhang Zhao1, Jiachen Li4, Susmita Bose5 and Amit Bandyopadhyay5,∗

Abstract

적층 제조는 바이메탈 및 다중 재료 구조의 제작 가능성을 제공합니다. 그러나 재료 호환성과 접착성은 부품의 성형성과 최종 품질에 직접적인 영향을 미칩니다. 적합한 프로세스를 기반으로 다양한 재료 조합의 기본 인쇄 가능성을 이해하는 것이 중요합니다.

여기에서는 두 가지 일반적이고 매력적인 재료 조합(니켈 및 철 기반 합금)의 인쇄 적성 차이가 레이저 지향 에너지 증착(DED)을 통해 거시적 및 미시적 수준에서 평가됩니다.

증착 프로세스는 현장 고속 이미징을 사용하여 캡처되었으며, 용융 풀 특징 및 트랙 형태의 차이점은 특정 프로세스 창 내에서 정량적으로 조사되었습니다. 더욱이, 다양한 재료 쌍으로 처리된 트랙과 블록의 미세 구조 다양성이 비교적 정교해졌고, 유익한 다중 물리 모델링을 통해 이종 재료 쌍 사이에 제시된 기계적 특성(미세 경도)의 불균일성이 합리화되었습니다.

재료 쌍의 서로 다른 열물리적 특성에 의해 유발된 용융 흐름의 차이와 응고 중 결과적인 요소 혼합 및 국부적인 재합금은 재료 조합 간의 인쇄 적성에 나타난 차이점을 지배합니다.

이 작업은 서로 다른 재료의 증착에서 현상학적 차이에 대한 심층적인 이해를 제공하고 바이메탈 부품의 보다 안정적인 DED 성형을 안내하는 것을 목표로 합니다.

Additive manufacturing provides achievability for the fabrication of bimetallic and
multi-material structures; however, the material compatibility and bondability directly affect the
parts’ formability and final quality. It is essential to understand the underlying printability of
different material combinations based on an adapted process. Here, the printability disparities of
two common and attractive material combinations (nickel- and iron-based alloys) are evaluated
at the macro and micro levels via laser directed energy deposition (DED). The deposition
processes were captured using in situ high-speed imaging, and the dissimilarities in melt pool
features and track morphology were quantitatively investigated within specific process
windows. Moreover, the microstructure diversity of the tracks and blocks processed with varied
material pairs was comparatively elaborated and, complemented with the informative
multi-physics modeling, the presented non-uniformity in mechanical properties (microhardness)
among the heterogeneous material pairs was rationalized. The differences in melt flow induced
by the unlike thermophysical properties of the material pairs and the resulting element
intermixing and localized re-alloying during solidification dominate the presented dissimilarity
in printability among the material combinations. This work provides an in-depth understanding
of the phenomenological differences in the deposition of dissimilar materials and aims to guide
more reliable DED forming of bimetallic parts.

Figure 2. Deposition process and the track morphology. (a)–(c) Display the in situ captured tableaux of melt propagation and some physical
features during depositing for P1B1, P1B2, and P1B3, respectively. (d) The profiles of the melt pool at a frame of (t0 + 1) ms, and the flow
streamlines in the molten pool of each case. (e) The outer surface of the formed tracks, in which the colored arrows mark the scanning
direction. (f) Cross-section of the tracks. The parameter set used for in situ imaging was P-1000 W, S-600 mm·min–1, F-18 g·min–1. All the
scale bars are 2 mm. — Figure 2. Deposition process and the track morphology. (a)–(c) Display the in situ captured tableaux of melt propagation and some physical features during depositing for P1B1, P1B2, and P1B3, respectively. (d) The profiles of the melt pool at a frame of (t0 + 1) ms, and the flow streamlines in the molten pool of each case. (e) The outer surface of the formed tracks, in which the colored arrows mark the scanning direction. (f) Cross-section of the tracks. The parameter set used for in situ imaging was P-1000 W, S-600 mm·min–1, F-18 g·min–1. All the scale bars are 2 mm.

References

[1] Tan C L, Weng F, Sui S, Chew Y and Bi G J 2021 Progress and perspectives in laser additive manufacturing of key aeroengine materials Int. J. Mach. Tools Manuf. 170 103804
[2] Bandyopadhyay A, Traxel K D, Lang M, Juhasz M, Eliaz N and Bose S 2022 Alloy design via additive manufacturing: advantages, challenges, applications and perspectives Mater. Today 52 207–24
[3] Sui S, Chew Y, Weng F, Tan C L, Du Z L and Bi G J 2022 Study of the intrinsic mechanisms of nickel additive for grain refinement and strength enhancement of laser aided additively manufactured Ti–6Al–4V Int. J. Extrem. Manuf. 4 035102
[4] Xue P S, Zhu L D, Xu P H, Ren Y, Xin B, Meng G R, Yang Z C and Liu Z 2021 Research on process optimization and microstructure of CrCoNi medium-entropy alloy formed by laser metal deposition Opt. Laser Technol. 142 107167
[5] Bandyopadhyay A, Traxel K D and Bose S 2021 Nature-inspired materials and structures using 3D printing Mater. Sci. Eng. R 145 100609
[6] Zuback J S, Palmer T A and DebRoy T 2019 Additive manufacturing of functionally graded transition joints between ferritic and austenitic alloys J. Alloys Compd. 770 995–1003
[7] Feenstra D R, Banerjee R, Fraser H L, Huang A, Molotnikov A and Birbilis N 2021 Critical review of the state of the art in multi-material fabrication via directed energy deposition Curr. Opin. Solid State Mater. Sci. 25 100924
[8] Wei C, Zhang Z Z, Cheng D X, Sun Z, Zhu M H and Li L 2021 An overview of laser-based multiple metallic material additive manufacturing: from macro- to micro-scales Int. J. Extrem. Manuf. 3 012003
[9] Gu D D, Shi X Y, Poprawe R, Bourell D L, Setchi R and Zhu J H 2021 Material-structure-performance integrated laser-metal additive manufacturing Science 372 eabg1487
[10] Bandyopadhyay A and Heer B 2018 Additive manufacturing of multi-material structures Mater. Sci. Eng. R 129 1–16
[11] Tammas-Williams S and Todd I 2017 Design for additive manufacturing with site-specific properties in metals and alloys Scr. Mater. 135 105–10
[12] Chen W, Gu D D, Yang J K, Yang Q, Chen J and Shen X F 2022 Compressive mechanical properties and shape memory effect of NiTi gradient lattice structures fabricated by laser powder bed fusion Int. J. Extrem. Manuf. 4 045002
[13] Svetlizky D, Das M, Zheng B L, Vyatskikh A L, Bose S, Bandyopadhyay A, Schoenung J M, Lavernia E J and Eliaz N 2021 Directed energy deposition (DED) additive manufacturing: physical characteristics, defects, challenges and applications Mater. Today 49 271–95
[14] Panwisawas C, Tang Y T and Reed R C 2020 Metal 3D printing as a disruptive technology for superalloys Nat. Commun. 11 2327
[15] Wang S H, Ning J S, Zhu L D, Yang Z C, Yan W T, Dun Y C, Xue P S, Xu P H, Bose S and Bandyopadhyay A 2022 Role of porosity defects in metal 3D printing: formation mechanisms, impacts on properties and mitigation strategies Mater. Today 59 133–60
[16] DebRoy T, Mukherjee T, Milewski J O, Elmer J W, Ribic B, Blecher J J and Zhang W 2019 Scientific, technological and economic issues in metal printing and their solutions Nat. Mater. 18 1026–32
[17] Afrouzian A, Groden C J, Field D P, Bose S and Bandyopadhyay A 2022 Additive manufacturing of Ti-Ni bimetallic structures Mater. Des. 215 110461
[18] Bandyopadhyay A, Zhang Y N and Onuike B 2022 Additive manufacturing of bimetallic structures Virtual Phys. Prototyp. 17 256–94
[19] Onuike B, Heer B and Bandyopadhyay A 2018 Additive manufacturing of Inconel 718—copper alloy bimetallic structure using laser engineered net shaping (LENSTM) Addit. Manuf. 21 133–40
[20] Sahasrabudhe H, Harrison R, Carpenter C and Bandyopadhyay A 2015 Stainless steel to titanium bimetallic structure using LENSTM Addit. Manuf. 5 1–8
[21] Li B Y, Han C J, Lim C W J and Zhou K 2022 Interface formation and deformation behaviors of an additively manufactured nickel-aluminum-bronze/15-5 PH multimaterial via laser-powder directed energy deposition Mater. Sci. Eng. A 829 142101
[22] Zhang X C, Pan T, Chen Y T, Li L, Zhang Y L and Liou F 2021 Additive manufacturing of copper-stainless steel hybrid components using laser-aided directed energy deposition J. Mater. Sci. Technol. 80 100–16
[23] Shinjo J and Panwisawas C 2022 Chemical species mixing during direct energy deposition of bimetallic systems using titanium and dissimilar refractory metals for repair and biomedical applications Addit. Manuf. 51 102654
[24] Wang D et al 2022 Recent progress on additive manufacturing of multi-material structures with laser powder bed fusion Virtual Phys. Prototyp. 17 329–65
[25] Lin X, Yue T M, Yang H O and Huang W D 2005 Laser rapid forming of SS316L/Rene88DT graded material Mater. Sci. Eng. A 391 325–36
[26] Melzer D, Dˇzugan J, Koukolíková M, Rzepa S and Vavˇrík J 2021 Structural integrity and mechanical properties of the functionally graded material based on 316L/IN718 processed by DED technology Mater. Sci. Eng. A 811 141038
[27] Melzer D, Dˇzugan J, Koukolíková M, Rzepa S, Dlouh´y J, Brázda M and Bucki T 2022 Fracture characterisation of vertically build functionally graded 316L stainless steel with Inconel 718 deposited by directed energy deposition process Virtual Phys. Prototyp. 17 821–40
[28] Zhang Y N and Bandyopadhyay A 2018 Direct fabrication of compositionally graded Ti-Al2O3 multi-material structures using laser engineered net shaping Addit. Manuf. 21 104–11
[29] Ben-Artzy A, Reichardt A, Borgonia P J, Dillon R P, McEnerney B, Shapiro A A and Hosemann P 2021 Compositionally graded SS316 to C300 maraging steel using additive manufacturing Mater. Des. 201 109500
[30] Tan C L, Liu Y C, Weng F, Ng F L, Su J L, Xu Z K, Ngai X D and Chew Y 2022 Additive manufacturing of voxelized heterostructured materials with hierarchical phases Addit. Manuf. 54 102775
[31] Chen J, Yang Y Q, Song C H, Zhang M K, Wu S B and Wang D 2019 Interfacial microstructure and mechanical properties of 316L/CuSn10 multi-material bimetallic structure fabricated by selective laser melting Mater. Sci. Eng. A 752 75–85
[32] Wei C, Gu H, Gu Y C, Liu L C, Huang Y H, Cheng D X, Li Z Q and Li L 2022 Abnormal interfacial bonding mechanisms of multi-material additive-manufactured tungsten–stainless steel sandwich structure Int. J. Extrem. Manuf. 4 025002
[33] Zhang Y N and Bandyopadhyay A 2021 Influence of compositionally graded interface on microstructure and compressive deformation of 316L stainless steel to Al12Si aluminum alloy bimetallic structures ACS Appl. Mater. Interfaces 13 9174–85
[34] Wei C et al 2022 Cu10Sn to Ti6Al4V bonding mechanisms in laser-based powder bed fusion multiple material additive 15 Int. J. Extrem. Manuf. 6 (2024) 025001 J Ning et al manufacturing with different build strategies Addit. Manuf. 51 102588
[35] Li W, Karnati S, Kriewall C, Liou F, Newkirk J, Brown Taminger K M and Seufzer W J 2017 Fabrication and characterization of a functionally graded material from Ti-6Al-4V to SS316 by laser metal deposition Addit. Manuf. 14 95–104
[36] Shi Q M, Zhong G Y, Sun Y, Politis C and Yang S F 2021 Effects of laser melting+remelting on interfacial macrosegregation and resulting microstructure and microhardness of laser additive manufactured H13/IN625 bimetals J. Manuf. Process. 71 345–55
[37] Zhang W X, Hou W Y, Deike L and Arnold C 2022 Understanding the Rayleigh instability in humping phenomenon during laser powder bed fusion process Int. J. Extrem. Manuf. 4 015201
[38] Chen Y W, Zhang X, Li M M, Xu R Q, Zhao C and Sun T 2020 Laser powder bed fusion of Inconel 718 on 316 stainless steel Addit. Manuf. 36 101500
[39] Yang Z C, Wang S H, Zhu L D, Ning J S, Xin B, Dun Y C and Yan W T 2022 Manipulating molten pool dynamics during metal 3D printing by ultrasound Appl. Phys. Rev. 9 021416
[40] Hofmann D C, Roberts S, Otis R, Kolodziejska J, Dillon R P, Suh J O, Shapiro A A, Liu Z K and Borgonia J P 2014 Developing gradient metal alloys through radial deposition additive manufacturing Sci. Rep. 4 5357
[41] Tumkur T U et al 2021 Nondiffractive beam shaping for enhanced optothermal control in metal additive manufacturing Sci. Adv. 7 eabg9358
[42] Scipioni Bertoli U, Guss G, Wu S, Matthews M J and Schoenung J M 2017 In-situ characterization of laser-powder interaction and cooling rates through high-speed imaging of powder bed fusion additive manufacturing Mater. Des. 135 385–96
[43] Siva Prasad H, Brueckner F and Kaplan A F H 2020 Powder incorporation and spatter formation in high deposition rate blown powder directed energy deposition Addit. Manuf. 35 101413
[44] Ebrahimi A, Kleijn C R and Richardson I M 2021 Numerical study of molten metal melt pool behaviour during conduction-mode laser spot melting J. Appl. Phys. 54 105304
[45] Mumtaz K A and Hopkinson N 2010 Selective laser melting of thin wall parts using pulse shaping J. Mater. Process. Technol. 210 279–87
[46] Sikandar Iquebal A, Yadav A, Botcha B, Krishna Gorthi R and Bukkapatnam S 2022 Tracking and quantifying spatter characteristics in a laser directed energy deposition process using Kalman filter Manuf. Lett. 33 692–700
[47] Criales L E, Arısoy Y M, Lane B, Moylan S, Donmez A and Özel T 2017 Laser powder bed fusion of nickel alloy 625: experimental investigations of effects of process parameters on melt pool size and shape with spatter analysis Int. J. Mach. Tools Manuf. 121 22–36
[48] Coen V, Goossens L and van Hooreweder B 2022 Methodology and experimental validation of analytical melt pool models for laser powder bed fusion J. Mater. Process. Technol. 304 117547
[49] Zhao C, Shi B, Chen S L, Du D, Sun T, Simonds B J, Fezzaa K and Rollett A D 2022 Laser melting modes in metal powder bed fusion additive manufacturing Rev. Mod. Phys. 94 045002
[50] Wang J H, Han F Z, Chen S F and Ying W S 2019 A novel model of laser energy attenuation by powder particles for laser solid forming Int. J. Mach. Tools Manuf. 145 103440
[51] Haley J C, Schoenung J M and Lavernia E J 2018 Observations of particle-melt pool impact events in directed energy deposition Addit. Manuf. 22 368–74
[52] Chen Y H et al 2021 Correlative synchrotron x-ray imaging and diffraction of directed energy deposition additive manufacturing Acta Mater. 209 116777
[53] Khorasani M, Ghasemi A, Leary M, Cordova L, Sharabian E, Farabi E, Gibson I, Brandt M and Rolfe B 2022 A comprehensive study on meltpool depth in laser-based powder bed fusion of Inconel 718 Int. J. Adv. Manuf. Technol. 120 2345–62
[54] Shamsaei N, Yadollahi A, Bian L and Thompson S M 2015 An overview of direct laser deposition for additive manufacturing; part II: mechanical behavior, process parameter optimization and control Addit. Manuf. 8 12–35
[55] Ghanavati R, Naffakh-Moosavy H, Moradi M and Eshraghi M 2022 Printability and microstructure of directed energy deposited SS316l-IN718 multi-material: numerical modeling and experimental analysis Sci. Rep. 12 16600
[56] Galbusera F, Demir A G, Platl J, Turk C, Schnitzer R and Previtali B 2022 Processability and cracking behaviour of novel high-alloyed tool steels processed by laser powder bed fusion J. Mater. Process. Technol. 302 117435
[57] Wang A et al 2023 Effects of processing parameters on pore defects in blue laser directed energy deposition of aluminum by in and ex situ observation J. Mater. Process. Technol. 319 118068
[58] Hinojos A, Mireles J, Reichardt A, Frigola P, Hosemann P, Murr L E and Wicker R B 2016 Joining of Inconel 718 and 316 stainless steel using electron beam melting additive manufacturing technology Mater. Des. 94 17–27
[59] Yang Z C, Zhu L D, Wang S H, Ning J S, Dun Y C, Meng G R, Xue P S, Xu P H and Xin B 2021 Effects of ultrasound on multilayer forming mechanism of Inconel 718 in directed energy deposition Addit. Manuf. 48 102462
[60] Yao L M, Huang S, Ramamurty U and Xiao Z M 2021 On the formation of “Fish-scale” morphology with curved grain interfacial microstructures during selective laser melting of dissimilar alloys Acta Mater. 220 117331
[61] Ghanavati R, Naffakh-Moosavy H and Moradi M 2021 Additive manufacturing of thin-walled SS316L-IN718 functionally graded materials by direct laser metal deposition J. Mater. Res. Technol. 15 2673–85
[62] Chen N N, Khan H A, Wan Z X, Lippert J, Sun H, Shang S L, Liu Z K and Li J J 2020 Microstructural characteristics and crack formation in additively manufactured bimetal material of 316L stainless steel and Inconel 625 Addit. Manuf. 32 101037
[63] Xiao Y H, Wan Z X, Liu P W, Wang Z, Li J J and Chen L 2022 Quantitative simulations of grain nucleation and growth at additively manufactured bimetallic interfaces of SS316L and IN625 J. Mater. Process. Technol. 302 117506
[64] Mukherjee T, DebRoy T, Lienert T J, Maloy S A and Hosemann P 2021 Spatial and temporal variation of hardness of a printed steel part Acta Mater. 209 116775
[65] Dinda G P, Dasgupta A K and Mazumder J 2021 Texture control during laser deposition of nickel-based superalloy Scr. Mater. 67 503–6
[66] Tan Z E, Pang J H L, Kaminski J and Pepin H 2019 Characterisation of porosity, density, and microstructure of directed energy deposited stainless steel AISI 316L Addit. Manuf. 25 286–96
[67] Wolff S J, Gan Z T, Lin S, Bennett J L, Yan W T, Hyatt G, Ehmann K F, Wagner G J, Liu W K and Cao J 2019 Experimentally validated predictions of thermal history and microhardness in laser-deposited Inconel 718 on carbon steel Addit. Manuf. 27 540–51 16 Int. J. Extrem. Manuf. 6 (2024) 025001 J Ning et al
[68] Zhang L, Wen M, Imade M, Fukuyama S and Yokogawa K 2008 Effect of nickel equivalent on hydrogen gas embrittlement of austenitic stainless steels based on type 316 at low temperatures Acta Mater. 56 3414–21
[69] Zuback J S and DebRoy T 2018 The hardness of additively manufactured alloys Materials 11 2070
[70] Adomako N K, Lewandowski J J, Arkhurst B M, Choi H, Chang H J and Kim J H 2022 Microstructures and mechanical properties of multi-layered materials composed of Ti-6Al-4V, vanadium, and 17–4PH stainless steel produced by directed energy deposition Addit. Manuf. 59 103174

원문 PDF 보기

Fig. 3. (a–c) Snapshots of the CtFD simulation of laser-beam irradiation: (a) Top, (b) longitudinal vertical cross-sectional, and (c) transversal vertical cross-sectional views. (d) z-position of the solid/liquid interface during melting and solidification.

Solute segregation in a rapidly solidified Hastelloy-X Ni-based superalloy during laser powder bed fusion investigated by phase-field simulations and computational thermal-fluid dynamics

Masayuki Okugawa ^ab, Kenji Saito ^a, Haruki Yoshima ^a, Katsuhiko Sawaizumi ^a, Sukeharu Nomoto ^c, Makoto Watanabe ^c, Takayoshi Nakano ^ab, Yuichiro Koizumi ^abShow moreAdd to MendeleyShareCite

https://doi.org/10.1016/j.addma.2024.104079

Get rights and content Under a Creative Commons license open access

Abstract

Solute segregation significantly affects material properties and is a critical issue in the laser powder-bed fusion (LPBF) additive manufacturing (AM) of Ni-based superalloys. To the best of our knowledge, this is the first study to demonstrate a computational thermal-fluid dynamics (CtFD) simulation coupled multi-phase-field (MPF) simulation with a multicomponent-composition model of Ni-based superalloy to predict solute segregation under solidification conditions in LPBF. The MPF simulation of the Hastelloy-X superalloy reproduced the experimentally observed submicron-sized cell structure. Significant solute segregations were formed within interdendritic regions during solidification at high cooling rates of up to 10⁸K s^-1, a characteristic feature of LPBF. Solute segregation caused a decrease in the solidus temperature (T_S), with a reduction of up to 30.4 K, which increases the risk of liquation cracks during LPBF. In addition, the segregation triggers the formation of carbide phases, which increases the susceptibility to ductility dip cracking. Conversely, we found that the decrease in T_S is suppressed at the melt-pool boundary regions, where re-remelting occurs during the stacking of the layer above. Controlling the re-remelting behavior is deemed to be crucial for designing crack-free alloys. Thus, we demonstrated that solute segregation at the various interfacial regions of Ni-based multicomponent alloys can be predicted by the conventional MPF simulation. The design of crack-free Ni-based superalloys can be expedited by MPF simulations of a broad range of element combinations and their concentrations in multicomponent Ni-based superalloys.

Graphical abstract

Keywords

Laser powder-bed fusion, Hastelloy-X Nickel-based superalloy, solute element segregation, computational thermal-fluid dynamics simulation, phase-field method

1. Introduction

Additive manufacturing (AM) technologies have attracted considerable attention as they allow us to easily build three-dimensional (3D) parts with complex geometries. Among the wide range of available AM techniques, laser powder-bed fusion (LPBF) has emerged as a preferred technique for metal AM [1], [2], [3], [4], [5]. In LPBF, metal products are built layer-by-layer by scanning laser, which fuse metal powder particles into bulk solids.

Significant attempts have been made to integrate LPBF techniques within the aerospace industry, with a particular focus on weldable Ni-based superalloys, such as IN718 [6], [7], [8], IN625 [9], [10], and Hastelloy-X (HX) [11], [12], [13], [14]. Non-weldable alloys, such as IN738LC [15], [16] and CMSX-4 [1], [17] are also suitable for their sufficient creep resistance under higher temperature conditions. However, non-weldable alloys are difficult to build using LPBF because of their susceptibility to cracking during the process. In general, a macro solute-segregation during solidification is suppressed by the rapid cooling conditions (up to 10⁸ K s^-1) unique to the LPBF process [18]. However, the solute segregation still occurs in the interdendritic regions that are smaller than the micrometer scale [5], [19], [20], [21]; these regions are suggested to be related to the hot cracks in LPBF-fabricated parts. Therefore, an understanding of solute segregation is essential for the fabrication of reliable LPBF-fabricated parts while avoiding cracks.

The multiphase-field (MPF) method has gained popularity for modeling the microstructure evolution and solute segregation under rapid cooling conditions [5], [20], [21], [22], [23], [24], [25], [26], [27], [28]. Moreover, quantifiable predictions have been achieved by combining the MPF method with temperature distribution analysis methods such as the finite-element method (FEM) [20] and computational thermal-fluid dynamics (CtFD) simulations [28]. These aforementioned studies have used binary-approximated multicomponent systems, such as Ni–Nb binary alloys, to simulate IN718 alloys. While MPF simulations using binary alloy systems can effectively reproduce microstructure formations and segregation behaviors, the binary approximation might be affected by the chemical interactions between the removed solute elements in the target multicomponent alloy. The limit of absolute stability predicted by the Mullins-Sekerka theory [29] is also crucial because the limit velocity is close to the solidification rate in the LPBF process and is different in multicomponent and binary-approximated systems. The difference between the solidus and liquidus temperatures, ΔT₀, directly determines the absolute stability according to the Mullins-Sekerka theory. For example, the ΔT₀ values of IN718 and its binary-approximated Ni–5 wt.%Nb alloy are 134 K [28] and 71 K [30], respectively. The solidification rate compared to the limit of absolute stability, i.e., the relative non-equilibrium of solidification, changes by simplification of the system. It is therefore important to use the composition of the actual multicomponent system in such simulations. However, to the best of our knowledge, there is no MPF simulation using a multicomponent model coupled with a temperature analysis simulation to predict solute segregation in a Ni-based superalloy.

In this study, we demonstrate that the conventional MPF model can reproduce experimentally observed dendritic structures by performing a phase-field simulation using the temperature distribution obtained by a CtFD simulation of a multicomponent Ni-based alloy (conventional solid-solution hardening-type HX). The MPF simulation revealed that the segregation behavior of solute elements largely depends on the regions of the melt pool, such as the cell boundary, the interior of the melt-pool boundary, and heat-affected regions. The sensitivities of the various interfaces to liquation and solidification cracks are compared based on the predicted concentration distributions. Moreover, the feasibility of using the conventional MPF model for LPBF is discussed in terms of the absolute stability limit.

2. Methods

2.1. Laser-beam irradiation experiments

Rolled and recrystallized HX ingots with dimensions of 20 × 50 × 10 mm were used as the specimens for laser-irradiation experiments. The specimens were irradiated with a laser beam scanned along straight lines of 10 mm in length using a laser AM machine (EOS 290 M, EOS) equipped with a 400 W Yb-fiber laser. Irradiation was performed with a beam power of P = 300 W and a scanning speed of V = 600 mm s^-1, which are the conditions generally used in the LPBF fabrication of Ni-based superalloy [8]. The corresponding line energy was 0.5 J mm^-1. The samples were cut perpendicular to the beam-scanning direction for cross-sectional observation using a field-emission scanning electron microscope (FE-SEM, JEOL JSM 6500). Crystal orientation analysis was performed by electron backscatter diffraction (EBSD). The sizes of each crystal grain and their aspect ratios were evaluated by analyzing the EBSD data.

2.2. CtFD simulation

CtFD simulations of the laser-beam irradiation of HX were performed using a 3D thermo-fluid analysis software (Flow Science FLOW-3D® with Flow-3D Weld module). A Gaussian heat source model was used, in which the irradiation intensity distribution of the beam is regarded as a symmetrical Gaussian distribution over the entire beam. The distribution of the beam irradiation intensity is expressed by the following equation.(1)q̇=2ηPπR2exp−2r2R2.

Here, P is the power, R is the effective beam radius, r is the actual beam radius, and η is the beam absorption rate of the substrate. To improve the accuracy of the model, η was calculated by assuming multiple reflections using the Fresnel equation:(2)�=1−121+1−�cos�21+1+�cos�2+�2−2�cos�+2cos2��2+2�cos�+2cos2�.

ε is the Fresnel coefficient and θ is the incident angle of the laser. A local laser melt causes the vaporization of the material and results in a high vapor pressure. This vapor pressure acts as a recoil pressure on the surface, pushing the weld pool down. The recoil pressure is reproduced using the following equation.(3)precoil=Ap0exp∆HLVRTV1−TVT.

Here, p₀ is the atmospheric pressure, ∆H_LV is the latent heat of vaporization, R is the gas constant, and T_V is the boiling point at the saturated vapor pressure. A is a ratio coefficient that is generally assumed to be 0.54, indicating that the recoil pressure due to evaporation is 54% of the vapor pressure at equilibrium on the liquid surface.

Table 1 shows the parameters used in the simulations. Most parameters were evaluated using an alloy physical property calculation software (Sente software JMatPro v11). The values in a previously published study [31] were used for the emissivity and the Stefan–Boltzmann constant, and the values for pure Ni [32] were used for the heat of vaporization and vaporization temperatures. The Fresnel coefficient, which determines the beam absorption efficiency, was used as a fitting parameter to reproduce the morphology of the experimentally observed melt region, and a Fresnel coefficient of 0.12 was used in this study.

Table 1. Parameters used in the CtFD simulations.

Parameter	Symbol	Value	Reference
Density at 298.15 K	ρ	8.24 g cm^-3	[^⁎]
Liquidus temperature	T_L	1628.15 K	[^⁎]
Solidus temperature	T_S	1533.15 K	[^⁎]
Viscosity at T_L	η	6.8 g m^-1 s^-1	[^⁎]
Specific heat at 298.15 K	C_P	0.439 J g^-1 K^-1	[^⁎]
Thermal conductivity at 298.15 K	λ	10.3 W m^-1 K^-1	[^⁎]
Surface tension at T_L	γ_L	1.85 J m^-2	[^⁎]
Temperature coefficient of surface tension	dγ_L/dT	–2.5 × 10⁻⁴ J m^-2 K^-1	[^⁎]
Emissivity	Ε	0.27	[31]
Stefan–Boltzmann constant	σ	5.67 × 10^-8W m^-2 K^-4	[31]
Heat of fusion	ΔH_SL	2.76 × 10² J g^-1	[32]
Heat of vaporization	ΔH_LV	4.29 × 10³J g^-1	[32]
Vaporization temperature	T_V	3110 K	[32]

⁎

Calculated using JMatPro v11.

The dimensions of the computational domain of the numerical model were 4.0 mm in the beam-scanning direction, 0.4 mm in width, and 0.3 mm in height. A uniform mesh size of 10 μm was applied throughout the computational domain. The boundary condition of continuity was applied to all boundaries except for the top surface. The temperature was initially set to 300 K. P and V were set to their experimental values, i.e., 300 W and 600 mm s^-1, respectively. Solidification conditions based on the temperature gradient, G, the solidification rate, R, and the cooling rate were evaluated, and the obtained temperature distribution was used in the MPF simulations.

2.3. MPF simulation

Two-dimensional MPF simulations weakly coupled with the CtFD simulation were performed using the Microstructure Evolution Simulation Software (MICRESS) [33], [34], [35], [36], [37] with the TQ-Interface for Thermo-Calc [38]. A simplified HX alloy composition of Ni-21.4Cr-17.6Fe-0.46Mn-8.80Mo-0.39Si-0.50W-1.10Co-0.08 C (mass %) was used in this study. The Gibbs free energy and diffusion coefficient of the system were calculated using the TCNI9 thermodynamic database [39] and the MOBNi5 mobility database [40]. Τhe equilibrium phase diagram calculated using Thermo-Calc indicates that the face-centered cubic (FCC) and σ phases appear as the equilibrium solid phases [19]. However, according to the time-temperature-transformation (TTT) diagram [41], the phases are formed after the sample is maintained for tens of hours in a temperature range of 1073 to 1173 K. Therefore, only the liquid and FCC phases were assumed to appear in the MPF simulations. The simulation domain was 5 × 100 μm, and the grid size Δx and interface width were set to 0.025 and 0.1 µm, respectively. The interfacial mobility between the solid and liquid phases was set to 1.0 × 10^-8 m⁴ J^-1 s^-1. Initially, one crystalline nucleus with a [100] crystal orientation was placed at the left bottom of the simulation domain, with the liquid phase occupying the remainder of the domain. The model was solidified under the temperature field distribution obtained by the CtFD simulation. The concentration distribution and crystal orientation of the solidified model were examined. The primary dendrite arm space (PDAS) was compared to the experimental PDAS measured by the cross-sectional SEM observation.

In an actual LPBF process, solidified layers are remelted and resolidified during the stacking of the one layer above, thereby greatly affecting solute element distributions in those regions. Therefore, remelting and resolidification simulations were performed to examine the effect of remelting on solute segregation. The solidified model was remelted and resolidified by applying a time-dependent temperature field shifted by 60 μm in the height direction, assuming reheating during the stacking of the upper layer (i.e., the upper 40 μm region of the simulation box was remelted and resolidified). The changes in the composition distribution and formed microstructure were investigated.

3. Results

3.1. Experimental observation of melt pool

Fig. 1 shows a cross-sectional optical microscopy image and corresponding inverse pole figure (IPF) orientation maps obtained from the laser-melted region of HX. The dashed line indicates the fusion line. A deep melted region was formed by keyhole-mode melting due to the vaporization of the metal and resultant recoil pressure. Epitaxial growth from the unmelted region was observed. Columnar crystal grains with an average diameter of 5.46 ± 0.32 μm and an aspect ratio of 3.61 ± 0.13 appeared at the melt regions (Figs. 1b–1d). In addition, crystal grains growing in the z direction could be observed in the lower center.

Fig. 2a shows a cross-sectional backscattering electron image (BEI) obtained from the laser-melted region indicated by the black square in Fig. 1a. The bright particles with a diameter of approximately 2 μm observed outside the melt pool. It is well known that M₆C, M₂₃C₆, σ, and μ precipitate phases are formed in Hastelloy-X [41]. These precipitates mainly consisted of Mo, Cr, Fe, and Ni; The μ and M₆C phases are rich in Mo, while the σ and M₂₃C₆ phases are rich in Cr. The SEM energy dispersive X-ray spectroscopy analysis suggested that the bright particles are the stable precipitates as shown in Fig. S2 and Table S1. Conversely, there are no carbides in the melt pool. This suggests that the cooling rate is extremely high during LPBF, which prevents the formation of a stable carbide during solidification. Figs. 2b–2f show magnified BEI images at different height positions indicated in Fig. 2a. Bright regions are observed between the cells, which become fragmentary at the center of the melt pool, as indicated by the yellow arrow heads in Figs. 2e and 2f.

3.2. CtFD simulation

Figs. 3a–3c show snapshots of the CtFD simulation of HX at 2.72 ms, with the temperature indicated in color. A melt pool with an elongated teardrop shape formed and keyhole-mode melting was observed at the front of the melt region. The cooling rate, temperature gradient (G), and solidification rate (R) were evaluated from the temporal change in the temperature distribution of the CtFD simulation results. The z-position of the solid/liquid interface during the melting and solidification processes is shown in Fig. 3d. The interface goes down rapidly during melting and then rises during solidification. The MPF simulation of the microstructure formation during solidification was performed using the temperature distribution. Moreover, the microstructure formation process during the fabrication of the upper layer was investigated by remelting and resolidifying the solidified layer using the same temperature distribution with a 60 μm upward shift, corresponding to the layer thickness commonly used in the LPBF of Ni-based superalloys.

Figs. 4a–4c show the changes in the cooling rate, temperature gradient, and solidification rate in the center line of the melt pool parallel to the z direction. To output the solidification conditions at the solid/liquid interface in the melt pool, only the data of the mesh where the solid phase ratio was close to 0.5 were plotted. Solidification occurred where the cooling rate was in the range of 2.1 × 10⁵–1.6 × 10⁶K s^-1, G was in the range of 3.6 × 10⁵–1.9 × 10⁷K m^-1, and R was in the range of 8.2 × 10⁻²–6.3 × 10⁻¹ m s^-1. The cooling rate was the highest near the fusion line and decreased as the interface approached the center of the melt region (Fig. 4a). G also exhibited the highest value in the regions near the fusion line and decreased throughout the solid/liquid interface toward the center of the melt pool (Fig. 4b). R had the lowest value near the fusion line and increased as the interface approached the center of the melt region (Fig. 4c).

3.3. MPF simulations coupled with CtFD simulation

MPF simulations of solidification, remelting, and resolidification were performed using the temperature-time distribution obtained by the CtFD simulation. Fig. 5 shows the MPF solidified models colored by phase and Mo concentration. All the computational domains show the FCC phase after the solidification (Fig. 5a). Dendrites grew parallel to the heat flow direction, and solute segregations were observed in the interdendritic regions. At the bottom of the melt pool (Fig. 5d), planar interface growth occurred before the formation of primary dendrites. The bottom of the melt pool is the turning point of the solid/liquid interface from the downward motion in melting to the upward motion in solidification. Thus, the solidification rate at the boundary is zero, and is extremely low immediately above the molt-pool boundary. Here, the lower limit of the solidification rate (R) for dendritic growth can be represented by the constitutional supercooling criterion [29], V_cs = (G × D_L) / ΔT, and planar interface growth occurs at R < V_cs. D_L and ΔT denote the diffusion coefficient in the liquid and the equilibrium freezing range, respectively. The results suggest that planar interface growth occurs at the bottom of the melt pool, resulting in a dark region with a different solute element distribution. Some of the primary dendrites were diminished by competition with other dendrites. In addition, secondary dendrite arms could be seen in the upper regions (Fig. 5c), where solidification occurred at a lower cooling rate. The fragmentation of the solute segregation near the secondary dendrite arms is similar to that observed in the experimental melt pool shown in Figs. 2e and 2f, and the secondary dendrite arms are suggested to have appeared at the center of the melt region. Fig. 6 shows the PDASs measured from the MPF simulation models, compared to the experimental PDASs measured by the cross-sectional SEM observation of the laser-melted regions (Fig. 2). The PDAS obtained by the MPF simulation become larger as the solidification progress. Ghosh et al. [21] evident by the phase-field method that the PDAS decreases as the cooling rate increases under the rapid cooling conditions obtained by the finite element analysis. In this study, the cooling rate was decreased as the interface approached the center of the melt region (Fig. 4a), and the trends in PDAS changes with respect to cooling rate is same as the reported trend [21]. The simulated trends of the PDAS with the position in the melt pool agreed well with the experimental trends. However, all PDASs in the simulation were larger than those observed in the experiment at the same positions. Ode et al. [42] reported that PDAS differences between 2D and 3D MPF simulations can be represented by PDAS_2D = 1.12 × PDAS_3D owing to differences in the effects of the interfacial energy and diffusivity. We also performed 2D and 3D MPF simulations under the solidification conditions of G = 1.94 × 10⁷K m^-1 and R = 0.82 m s^-1 (Fig. S1), and found that the PDAS from the 2D MPF simulation was 1.26 times larger than that from the 3D simulation. Therefore, the cell structure obtained by the CtFD simulation coupled with the 2D MPF simulation agreed well with the experimental results over the entire melt pool region considering the dimensional effects.

Fig. 7b1 and 7c1 show the concentration profiles of the solidified model along the growth direction indicated by dashed lines in Fig. 7a. The differences in concentrations from the alloy composition are also shown in Fig. 7b2 and 7c2. Cr, Mo, C, Mn, and W were segregated to the interdendritic regions, while Si, Fe, and Co were depressed. The solute segregation behavior agrees with the experimentally observation [43] and the prediction by the Scheil-Gulliver simulation [19]. Segregation occurred to the highest degree in Mo, while the ratio of segregation to the alloy composition was remarkable in C. The concentration fluctuations correlated with the position in the melt pool and decreased at the center of the melt pool, which was suggested to correspond to the lower cooling rate in this region. Conversely, droplets that appeared between secondary dendrite arms in the upper regions of the simulation domain exhibited a locally high segregation of solute elements, with the same amount of segregation as that at the bottom of the melt pool.

3.4. Remelting and resolidification simulation

The solidified model was subjected to remelting and resolidification conditions by shifting the temperature profile upward by 60 µm to reveal the effect of reheating on the solute segregation behavior. Figs. 8a and 8b shows the simulation domains of the HX model after resolidification, colored by phase and Mo concentration. The magnified MPF models during the resolidification of the regions indicated by rectangles in Figs. 8a and 8b are also shown as Figs. 8c and 8d. Dendrites grew from the bottom of the remelted region, with the segregation of solute elements occurring in the interdendritic regions. The entire domain become the FCC phase after the resolidification, as shown in Fig. 8a. The bottom of the remelted regions exhibited a different microstructure, and Mo was depressed at the remelted regions, rather than the interdendritic regions. The different solute segregation behavior [44] and the microstructure formation [45] at the melt pool boundary is also observed in LPBF manufactured 316 L stainless steel. We found that this microstructure was formed by further remelting during the resolidification process, which is shown in Fig. 9. Here, the solidified HX model was heated, and the interdendritic regions were preferentially melted while concentration fluctuations were maintained (Fig. 9a1 and 9a2). Subsequently, planer interface growth occurs near the melt pool boundary where the solidification rate is almost zero, and the dendrites outside of the boundary are grown epitaxially (Fig. 9b1 and 9b2). However, these remelted again because of the temperature rise (Fig. 9c1 and 9c2, and the temperature-time profile shown in Fig. 9e). The remelted regions then cooled and solidified with the abnormal solute segregations (Fig. 9d1 and 9d2). Then, dendrite grows from amplified fluctuations under the solidification rate larger than the criterion of constitutional supercooling (Fig. 9d1, 9d2, and Fig. 8d). It has been reported [46], [47] that temperature rising owning to latent heat affects microstructure formation: phase-field simulations of a Ni–Al binary alloy suggest that the release of latent heat during solidification increases the average temperature of the system [46] and strongly influences the solidification conditions [47]. In this study, the release of latent heat during solidification is considered in CtFD simulations for calculating the temperature distribution, and the temperature increase is suggested to have also occurred due to the release of latent heat.

Fig. 10b1 and 10c1 show the solute element concentration line profiles of the resolidified model along the growth direction indicated by dashed lines in Fig. 10a. Fig. 10b2 and 10c2 show the corresponding differences in concentration from the alloy composition. The segregation behavior of solute elements at the interdendritic regions (Fig. 10b1 and 10b2) was the same as that in the solidified model (Figs. 7b1 and 7b2). Here, Cr, Mo, C, Mn, and W were segregated to the interdendritic regions, while Si, Fe, and Co were depressed. However, the concentration fluctuations at the interdendritic regions were larger than those in the solidified model. Moreover, the segregation of the outside of the melt pool, i.e., the heat-affected zone, was remarkable throughout remelting and resolidification. Different segregation behaviors were observed in the re-remelted region: Mo, Si, Mn, and W were segregated, while Ni, Fe, and Co were depressed. These solute segregations caused by remelting are expected to heavily influence the crack behavior.

4. Discussion

4.1. Effect of segregation of solute elements on liquation cracking susceptibility

Strong solute segregation was observed between the interdendritic regions of the solidified alloy (Fig. 7). In addition, the solute segregation behavior was significantly affected by remelting and resolidification and varied across the alloy. Solute segregation can be categorized by the regions shown in Fig. 11a1–11a4, namely the cell boundary (Fig. 11a1), interior of the melt-pool boundary (Fig. 11a2), re-remelted regions (Fig. 11a3), and heat-affected regions (Fig. 11a4). The concentration profiles of these regions are shown in Fig. 11b1–11b4. Solute segregation was the highest in the cell boundary region. The solute segregation in the heat-affected region was almost the same as that in the cell boundary region, but seemed to have been attenuated by reheating during remelting and resolidification. The interior of the melt-pool boundary region also had the same tendency for solute segregation. However, the amount of Cr segregation was smaller than that of Mo. A decrease in the Cr concentration was also mitigated, and the concentration remained the same as that in the alloy composition. Fig. 11c1–11c4 show the chemical potentials of the solute elements for the FCC phase at 1073 K calculated using the compositions of those interfacial regions. All the interfacial regions showed non-constant chemical potentials for each element along the perpendicular direction, but the fluctuations of the chemical potentials differed by the type of interfaces. In particular, the fluctuation of the chemical potential of C at the cell boundary region was the largest, suggesting it can be relaxed easily by heat treatment. On the other hand, the fluctuations of the other elements in all the regions were small. The solute segregations are most likely to remain after the heat treatment and are supposed to affect the cracking susceptibilities.

The solidus temperatures T_S, the difference between the liquidus and solidus temperatures (i.e., the brittle temperature range (BTR)), and the fractions of the equilibrium precipitate phases at 1073 K of the interfacial regions were calculated as the liquation, solidification, and ductility dip cracking susceptibilities, respectively. At the cell boundary (Fig. 12a1), interior of the melt-pool boundary (Fig. 12a1), and heat-affected regions (Fig. 12a1), the internal and interfacial regions exhibited higher and lower T_S compared to that of the alloy composition, respectively. The lowest T_s was obtained with the composition at the cell boundary region, which is the largest solute-segregated region. It has been suggested that strong segregations of solute elements in LPBF lead to liquation cracks [16]. This study also supports this suggestion, and liquation cracks are more likely to occur at the interfacial regions indicated by predicting the solute segregation behavior using the MPF model. Additionally, the BTRs of the cell boundary, interior of the melt-pool boundary, and heat-affected regions were wider at the interdendritic regions, and solidification cracks were also likely to occur in these regions. Moreover, within the solute segregation regions, the fraction of the precipitate phases in these interfacial regions was larger than that calculated using the alloy composition (Fig. 12c1, 12c2, and 12c4). This indicates that ductility dip cracking is also likely to occur at the cell boundary, interior of the melt-pool boundary, and in heat-affected regions. Contrarily, we found that the re-remelted region exhibited a higher T_S and smaller BTR even in the interfacial region (Fig. 12a3 and 12b3), where the solute segregation behavior was different from that of the other regions. In addition, the re-remelting region exhibited less precipitation compared with the other segregated regions (Fig. 12c3). The re-remelting caused by the latent heat can attenuate solute segregation, prevent T_s from decreasing, decrease the BTR, and decrease the amount of precipitate phases. Alloys with a large amount of latent heat are expected to increase the re-remelting region, thereby decreasing the susceptibility to liquation and ductility dip cracks due to solute element segregation. This can be a guide for designing alloys for the LPBF process. As mentioned in Section 3.4, the microstructure [45] and the solute segregation behavior [44] at the melt pool boundary of LPBF-manufactured 316 L stainless steel are observed, and they are different from that of the interdendritic regions. Experimental observations of the solute segregation behavior in the LPBF-fabricated Ni-based alloys are currently underway.

4.2. Applicability of the conventional MPF simulation to microstructure formation under LPBF

As the solidification growth rate increases, segregation coefficients approach 1, and the fluctuation of the solid/liquid interface is suppressed by the interfacial tension. The interface growth occurs in a flat fashion instead of having a cellular morphology at a velocity above the absolute stability limit, R_as, predicted by the Mullins-Sekerka theory [29]: R_as = (ΔT₀ D_L) / (k Γ) where ΔT₀, D_L, k, and Γ are the difference between the liquidus and solidus temperatures, equilibrium segregation coefficient, the diffusivity of liquid, and the Gibbs-Thomson coefficient, respectively.

The R_as of HX was calculated using the equation and the thermodynamic parameters obtained by the TCNI9 thermodynamic database [39]. The calculated R_as of HX was 3.9 m s^-1 and is ten times larger than that of the Ni–Nb alloy (approximately 0.4 m s^-1) [20]. The HX alloy was solidified under R values in the range of 8.2 × 10⁻²–6.3 × 10⁻¹ m s^-1. The theoretically calculated criterion is larger than the evaluated R, and is in agreement with the experiment in which dendritic growth is observed in the melt pool (Fig. 5). In contrast, Karayagiz et al. [20] reported that the R of the Ni–Nb binary alloy under LPBF was as high as approximately 2 m s^-1, and planar interface growth was observed to be predominant under the high-growth-rate conditions. These experimentally observed microstructures agree well with the prediction by the Mullins-Sekerka theory about the relationship between the morphology and solidification rates.

In this study, the solidification microstructure formed by the laser-beam irradiation of an HX multicomponent Ni-based superalloy was reproduced by a conventional MPF simulation, in which the system was assumed to be in a quasi-equilibrium condition. Boussinot et al. [24] also suggested that the conventional phase-field model can be applied to simulate the microstructure of an IN718 multicomponent Ni-based superalloy in LPBF. In contrast, Kagayaski et al. [20] suggested that the conventional MPF simulation cannot be applied to the solidification of the Ni-Nb binary alloy system and that the finite interface dissipation model proposed by Steinbach et al. [48], [49] is necessary to simulate the high solidification rates observed in LPBF. The difference in the applicability of the conventional MPF method to HX and Ni–Nb binary alloys is presumed to arise from the differences in the non-equilibrium degree of these systems under the high solidification rates of LPBF. The results suggest that R_as can be used as a simple index to apply the conventional MPF model for solidification in LPBF. Solidification becomes a non-equilibrium process as the solidification rate approaches the limit of absolute stability, R_as. In this study, the solidification of the HX multicomponent system occurred under a relatively low solidification rate compared to R_as, and the microstructure of the conventional MPF model was successfully reproduced in the physical experiment. However, note that the limit of absolute stability predicted by the Mullins-Sekerka theory was originally proposed for solidification in a binary alloy system, and further investigation is required to consider its applicability to multicomponent alloy systems. Moreover, the fast solidification, such as in the LPBF process, causes segregation coefficient approaching a value of 1 [20], [21], [25] corresponds to a diffusion length that is on the order of the atomic interface thickness. When the segregation coefficient approaches 1, solute undercooling disappears; hence, there is no driving force to amplify fluctuations regardless of whether interfacial tension is present. This phenomenon should be further investigated in future studies.

5. Conclusions

We simulated solute segregation in a multicomponent HX alloy under the LPBF process by an MPF simulation using the temperature distributions obtained by a CtFD simulation. We set the parameters of the CtFD simulation to match the melt pool shape formed in the laser-irradiation experiment and found that solidification occurred under high cooling rates of up to 1.6 × 10⁶K s^-1.

MPF simulations using the temperature distributions from CtFD simulation could reproduce the experimentally observed PDAS and revealed that significant solute segregation occurred at the interdendritic regions. Equilibrium thermodynamic calculations using the alloy compositions of the segregated regions when considering crack sensitivities suggested a decrease in the solidus temperature and an increase in the amount of carbide precipitation, thereby increasing the susceptibility to liquation and ductility dip cracks in these regions. Notably, these changes were suppressed at the melt-pool boundary region, where re-remelting occurred during the stacking of the layer above. This effect can be used to achieve a novel in-process segregation attenuation.

Our study revealed that a conventional MPF simulation weakly coupled with a CtFD simulation can be used to study the solidification of multicomponent alloys in LPBF, contrary to the cases of binary alloys investigated in previous studies. We discussed the applicability of the conventional MPF model to the LPBF process in terms of the limit of absolute stability, R_as, and suggested that alloys with a high limit velocity, i.e., multicomponent alloys, can be simulated using the conventional MPF model even under the high solidification velocity conditions of LPBF.

CRediT authorship contribution statement

Masayuki Okugawa: Writing – review & editing, Writing – original draft, Visualization, Validation, Software, Methodology, Investigation, Formal analysis, Data curation, Conceptualization. Takayoshi Nakano: Writing – review & editing, Validation, Supervision, Funding acquisition. Yuichiro Koizumi: Writing – review & editing, Visualization, Validation, Supervision, Project administration, Methodology, Investigation, Funding acquisition, Formal analysis, Data curation, Conceptualization. Sukeharu Nomoto: Writing – review & editing, Validation, Investigation. Makoto Watanabe: Writing – review & editing, Validation, Supervision, Funding acquisition. Katsuhiko Sawaizumi: Validation, Software, Investigation, Formal analysis, Data curation. Kenji Saito: Visualization, Validation, Software, Methodology, Investigation, Formal analysis, Data curation. Haruki Yoshima: Visualization, Validation, Software, Investigation, Formal analysis, Data curation.

Declaration of Competing Interest

The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper

Acknowledgments

This work was partly supported by the Cabinet Office, Government of Japan, Cross-ministerial Strategic Innovation Promotion Program (SIP), “Materials Integration for Revolutionary Design System of Structural Materials,” (funding agency: The Japan Science and Technology Agency), by JSPS KAKENHI Grant Numbers 21H05018 and 21H05193, and by CREST Nanomechanics: Elucidation of macroscale mechanical properties based on understanding nanoscale dynamics for innovative mechanical materials (Grant Number: JPMJCR2194) from the Japan Science and Technology Agency (JST). The authors would like to thank Mr. H. Kawabata and Mr. K. Kimura for their technical support with the sample preparations and laser beam irradiation experiments.

Appendix A. Supplementary material

Download : Download Word document (654KB)

Supplementary material.

Data availability

Data will be made available on request.

References

[1]M. Ramsperger, R.F. Singer, C. KörnerMicrostructure of the nickel-base superalloy CMSX-4 fabricated by selective electron beam meltingMetall. Mater. Trans. A Phys. Metall. Mater. Sci., 47 (2016), pp. 1469-1480, 10.1007/s11661-015-3300-y View at publisher This article is free to access.View in Scopus Google Scholar
[2]J.H. Martin, B.D. Yahata, J.M. Hundley, J.A. Mayer, T.A. Schaedler, T.M. Pollock3D printing of high-strength aluminium alloysNature, 549 (2017), pp. 365-369, 10.1038/nature23894 View at publisher View in Scopus Google Scholar
[3]K. Hagihara, T. NakanoControl of anisotropic crystallographic texture in powder bed fusion additive manufacturing of metals and ceramics—A reviewJOM, 74 (2021), pp. 1760-1773, 10.1007/s11837-021-04966-7 View at publisher This article is free to access.Google Scholar
[4]Y. Koizumi, M. OkugawaDigital twin science of metal powder bed fusion additive manufacturing: A selective review of simulations for integrated computational materials engineering and scienceISIJ Int, 62 (2022), pp. 2183-2196, 10.2355/isijinternational.ISIJINT-2022-184 View at publisher View in Scopus Google Scholar
[5]S. Ghosh, J. Zollinger, M. Zaloznik, D. Banerjee, C.K. Newman, R. ArroyaveModeling of hierarchical solidification microstructures in metal additive manufacturing: Challenges and opportunitiesAddit. Manuf., 78 (2023), Article 103845, 10.1016/j.addma.2023.103845 View PDF View article View in Scopus Google Scholar
[6]N. Raghavan, R. Dehoff, S. Pannala, S. Simunovic, M. Kirka, J. Turner, N. Carlson, S.S. BabuNumerical modeling of heat-transfer and the influence of process parameters on tailoring the grain morphology of IN718 in electron beam additive manufacturingActa Mater, 112 (2016), pp. 303-314, 10.1016/j.actamat.2016.03.063 View PDF View article View in Scopus Google Scholar
[7]N. Raghavan, S. Simunovic, R. Dehoff, A. Plotkowski, J. Turner, M. Kirka, S. BabuLocalized melt-scan strategy for site specific control of grain size and primary dendrite arm spacing in electron beam additive manufacturingActa Mater, 140 (2017), pp. 375-387, 10.1016/j.actamat.2017.08.038 View PDF View article View in Scopus Google Scholar
[8]O. Gokcekaya, T. Ishimoto, S. Hibino, J. Yasutomi, T. Narushima, T. NakanoUnique crystallographic texture formation in Inconel 718 by laser powder bed fusion and its effect on mechanical anisotropyActa Mater, 212 (2021), Article 116876, 10.1016/j.actamat.2021.116876 View PDF View article View in Scopus Google Scholar
[9]T. Keller, G. Lindwall, S. Ghosh, L. Ma, B.M. Lane, F. Zhang, U.R. Kattner, E.A. Lass, J.C. Heigel, Y. Idell, M.E. Williams, A.J. Allen, J.E. Guyer, L.E. LevineApplication of finite element, phase-field, and CALPHAD-based methods to additive manufacturing of Ni-based superalloysActa Mater, 139 (2017), pp. 244-253, 10.1016/j.actamat.2017.05.003 View PDF View article View in Scopus Google Scholar
[10]F. Zhang, L.E. Levine, A.J. Allen, M.R. Stoudt, G. Lindwall, E.A. Lass, M.E. Williams, Y. Idell, C.E. CampbellEffect of heat treatment on the microstructural evolution of a nickel-based superalloy additive-manufactured by laser powder bed fusionActa Mater, 152 (2018), pp. 200-214, 10.1016/j.actamat.2018.03.017 View PDF View article View in Scopus Google Scholar
[11]N.J. Harrison, I. Todd, K. MumtazReduction of micro-cracking in nickel superalloys processed by Selective Laser Melting: A fundamental alloy design approachActa Mater, 94 (2015), pp. 59-68, 10.1016/j.actamat.2015.04.035 View PDF View article View in Scopus Google Scholar
[12]H. Wang, L. Chen, B. Dovgyy, W. Xu, A. Sha, X. Li, H. Tang, Y. Liu, H. Wu, M.S. PhamMicro-cracking, microstructure and mechanical properties of Hastelloy-X alloy printed by laser powder bed fusion: As-built, annealed and hot-isostatic pressedAddit. Manuf., 39 (2021), Article 101853, 10.1016/j.addma.2021.101853 View PDF View article View in Scopus Google Scholar
[13]D. Tomus, P.A. Rometsch, M. Heilmaier, X. WuEffect of minor alloying elements on crack-formation characteristics of Hastelloy-X manufactured by selective laser meltingAddit. Manuf., 16 (2017), pp. 65-72, 10.1016/j.addma.2017.05.006 View PDF View article View in Scopus Google Scholar
[14]H. Kitano, M. Tsujii, M. Kusano, A. Yumoto, M. WatanabeEffect of plastic strain on the solidification cracking of Hastelloy-X in the selective laser melting processAddit. Manuf., 37 (2020), Article 101742, 10.1016/j.addma.2020.101742 View at publisher Google Scholar
[15]J. Xu, H. Gruber, D. Deng, R.L. Peng, J.J. MoverareShort-term creep behavior of an additive manufactured non-weldable Nickel-base superalloy evaluated by slow strain rate testingActa Mater, 179 (2019), pp. 142-157, 10.1016/j.actamat.2019.08.034 View PDF View article Google Scholar
[16]P. Kontis, E. Chauvet, Z. Peng, J. He, A.K. da Silva, D. Raabe, C. Tassin, J.J. Blandin, S. Abed, R. Dendievel, B. Gault, G. MartinAtomic-scale grain boundary engineering to overcome hot-cracking in additively-manufactured superalloysActa Mater, 177 (2019), pp. 209-221, 10.1016/j.actamat.2019.07.041 View PDF View article View in Scopus Google Scholar
[17]C. Körner, M. Ramsperger, C. Meid, D. Bürger, P. Wollgramm, M. Bartsch, G. EggelerMicrostructure and mechanical properties of CMSX-4 single crystals prepared by additive manufacturingMetall. Mater. Trans. A Phys. Metall. Mater. Sci., 49 (2018), pp. 3781-3792, 10.1007/s11661-018-4762-5 View at publisher This article is free to access.View in Scopus Google Scholar
[18]T. Ishimoto, R. Ozasa, K. Nakano, M. Weinmann, C. Schnitter, M. Stenzel, A. Matsugaki, T. Nagase, T. Matsuzaka, M. Todai, H.S. Kim, T. NakanoDevelopment of TiNbTaZrMo bio-high entropy alloy (BioHEA) super-solid solution by selective laser melting, and its improved mechanical property and biocompatibilityScr. Mater., 194 (2021), Article 113658, 10.1016/j.scriptamat.2020.113658 View PDF View article View in Scopus Google Scholar
[19]M. Okugawa, D. Izumikawa, Y. KoizumiSimulations of non-equilibrium and equilibrium segregation in nickel-based superalloy using modified Scheil-Gulliver and phase-field methodsMater. Trans., 61 (2020), pp. 2072-2078, 10.2320/matertrans.mt-ma2020005 View at publisher View in Scopus Google Scholar
[20]K. Karayagiz, L. Johnson, R. Seede, V. Attari, B. Zhang, X. Huang, S. Ghosh, T. Duong, I. Karaman, A. Elwany, R. ArróyaveFinite interface dissipation phase field modeling of Ni–Nb under additive manufacturing conditionsActa Mater, 185 (2020), pp. 320-339, 10.1016/j.actamat.2019.11.057 View PDF View article View in Scopus Google Scholar
[21]S. Ghosh, L. Ma, N. Ofori-Opoku, J.E. GuyerOn the primary spacing and microsegregation of cellular dendrites in laser deposited Ni-Nb alloysModel. Simul. Mater. Sci. Eng., 25 (2017), 10.1088/1361-651X/aa7369 View at publisher Google Scholar
[22]S. Nomoto, M. Segawa, M. WatanabeNon- and quasi-equilibrium multi-phase field methods coupled with CALPHAD database for rapid-solidification microstructural evolution in laser powder bed additive manufacturing conditionMetals, 11 (2021), p. 626, 10.3390/met11040626 View at publisher View in Scopus Google Scholar
[23]J. Kundin, L. Mushongera, H. EmmerichPhase-field modeling of microstructure formation during rapid solidification in Inconel 718 superalloyActa Mater, 95 (2015), pp. 343-356, 10.1016/j.actamat.2015.05.052 View PDF View article View in Scopus Google Scholar
[24]G. Boussinot, M. Apel, J. Zielinski, U. Hecht, J.H. SchleifenbaumStrongly out-of-equilibrium columnar solidification during laser powder-bed fusion in additive manufacturingPhys. Rev. Appl., 11 (2019), Article 014025, 10.1103/PhysRevApplied.11.014025 View at publisher View in Scopus Google Scholar
[25]K. Ji, E. Dorari, A.J. Clarke, A. KarmaMicrostructural pattern formation during far-from-equilibrium alloy solidificationPhys. Rev. Lett., 130 (2022), p. 26203, 10.1103/PhysRevLett.130.026203 View at publisher Google Scholar
[26]M. Okugawa, Y. Ohigashi, Y. Furishiro, Y. Koizumi, T. NakanoEquiaxed grain formation by intrinsic heterogeneous nucleation via rapid heating and cooling in additive manufacturing of aluminum-silicon hypoeutectic alloyJ. Alloys Compd., 919 (2022), Article 165812, 10.1016/j.jallcom.2022.165812 View PDF View article View in Scopus Google Scholar
[27]M. Okugawa, Y. Furushiro, Y. KoizumiEffect of rapid heating and cooling conditions on microstructure formation in powder bed fusion of Al-Si hypoeutectic alloy: A Phase-Field StudyMaterials, 15 (2022), p. 6092, 10.3390/ma15176092 View at publisher View in Scopus Google Scholar
[28]R. Acharya, J.A. Sharon, A. StaroselskyPrediction of microstructure in laser powder bed fusion processActa Mater, 124 (2017), pp. 360-371, 10.1016/j.actamat.2016.11.018 View PDF View article View in Scopus Google Scholar
[29]M. Rappaz, J.A. DantzigSolidification (first ed.), EFPL Press, Lausanne (2009)Google Scholar
[30]S.M. Elahi, R. Tavakoli, A.K. Boukellal, T. Isensee, I. Romero, D. TourretMultiscale simulation of powder-bed fusion processing of metallic alloysComput. Mater. Sci., 209 (2022), Article 111383, 10.1016/j.commatsci.2022.111383 View PDF View article View in Scopus Google Scholar
[31]C. Tang, J.L. Tan, C.H. WongA numerical investigation on the physical mechanisms of single track defects in selective laser meltingInt. J. Heat Mass Transf., 126 (2018), pp. 957-968, 10.1016/j.ijheatmasstransfer.2018.06.073 View PDF View article View in Scopus Google Scholar
[32]Technical Data for Nickel. Available online: 〈https://periodictable.com/Elements/028/data.html〉 (accessed on 16 January 2023).Google Scholar
[33]MICRostructure Evolution Simulation Software, Phase-Field Software Package. Available online: 〈https://micress.rwth-aachen.de〉 (accessed on 24 March 2023).Google Scholar
[34]J. Eiken, B. Böttger, I. SteinbachMultiphase-field approach for multicomponent alloys with extrapolation scheme for numerical applicationPhys. Rev. E – Stat. Nonlinear, Soft Matter Phys., 73 (2006), pp. 1-9, 10.1103/PhysRevE.73.066122 View at publisher View in Scopus Google Scholar
[35]B. Böttger, M. Apel, M. Budnitzki, J. Eiken, G. Laschet, B. ZhouCalphad coupled phase-field model with mechano-chemical contributions and its application to rafting of γ’ in CMSX-4Comput. Mater. Sci., 184 (2020), Article 109909, 10.1016/j.commatsci.2020.109909 View PDF View article View in Scopus Google Scholar
[36]C. Kumara, A. Ramanathan Balachandramurthi, S. Goel, F. Hanning, J. MoverareToward a better understanding of phase transformations in additive manufacturing of Alloy 718Materialia, 13 (2020), Article 100862View PDF View article View in Scopus Google Scholar
[37]B. Böttger, M. ApelPhase-field simulation of the formation of new grains by fragmentation during melting of an ABD900 superalloyIOP Conf. Ser. Mater. Sci. Eng., 1281 (2023), Article 012008, 10.1088/1757-899x/1281/1/012008 View at publisher This article is free to access.Google Scholar
[38]J.O. Andersson, T. Helander, L. Höglund, P. Shi, B. SundmanThermo-Calc & DICTRA, computational tools for materials scienceCalphad, 26 (2002), pp. 273-312, 10.1016/S0364-5916(02)00037-8 View PDF View article View in Scopus Google Scholar
[39]Thermo-Calc Software, Ni-Based Superalloys Database, Version 9. URL, 〈http://www.thermocalc.com/products-services/databases/thermodynamic/〉.Google Scholar
[40]Thermo-Calc Software, Ni-alloys Mobility Database, Version 5. URL, 〈https://www.thermocalc.com/products-services/databases/mobility/〉.Google Scholar
[41]J.C. Zhao, M. Larsen, V. RavikumarPhase precipitation and time-temperature-transformation diagram of Hastelloy XMater. Sci. Eng. A., 293 (2000), pp. 112-119, 10.1016/S0921-5093(00)01049-2 View PDF View article View in Scopus Google Scholar
[42]M. Ode, S.G. Kim, W.T. Kim, T. SuzukiNumerical prediction of the secondary dendrite arm spacing using a phase-field modelISIJ Int, 41 (2001), pp. 345-349, 10.2355/isijinternational.41.345 View at publisher View in Scopus Google Scholar
[43]S. Banoth, T.N. Palleda, T. Saito, H. Murakami, K. KakehiEffects of yttrium and silicon contents in Hastelloy-X built by selective laser melting processJ. Alloys Compd., 896 (2022), Article 163050, 10.1016/j.jallcom.2021.163050 View PDF View article View in Scopus Google Scholar
[44]K. Sato, S. Takagi, S. Ichikawa, T. Ishimoto, T. NakanoMicrostructure and Solute Segregation around the Melt-Pool Boundary of Orientation-Controlled 316L Austenitic Stainless Steel Produced by Laser Powder Bed FusionMaterials, 16 (2023), 10.3390/ma16010218 View at publisher Google Scholar
[45]Y. Liu, K. Nose, M. Okugawa, Y. Koizumi, T. NakanoFabrication and process monitoring of 316L stainless steel by laser powder bed fusion with µ-helix scanning strategy and narrow scanning line intervalsMater. Trans., 64 (2023), pp. 1135-1142, 10.2320/matertrans.MT-ME2022006 View at publisher View in Scopus Google Scholar
[46]H. Schaar, I. Steinbach, M. TegelerNumerical study of epitaxial growth after partial remelting during selective electron beam melting in the context of ni–alMetals, 11 (2021), pp. 2-13, 10.3390/met11122012 View at publisher Google Scholar
[47]M. Uddagiri, O. Shchyglo, I. Steinbach, B. Wahlmann, C. KoernerPhase-Field Study of the History-Effect of Remelted Microstructures on Nucleation During Additive Manufacturing of Ni-Based SuperalloysMetall. Mater. Trans. A Phys. Metall. Mater. Sci., 54 (2023), pp. 1825-1842, 10.1007/s11661-023-07004-0 View at publisher This article is free to access.View in Scopus Google Scholar
[48]I. Steinbach, L. Zhang, M. PlappPhase-field model with finite interface dissipationActa Mater, 60 (2012), pp. 2689-2701, 10.1016/j.actamat.2012.01.035 View PDF View article View in Scopus Google Scholar
[49]L. Zhang, I. SteinbachPhase-field model with finite interface dissipation: Extension to multi-component multi-phase alloysActa Mater, 60 (2012), pp. 2702-2710, 10.1016/j.actamat.2012.02.032 View PDF View article Google Scholar

Figure 5. Simulation of the molten pool under low-speed scanning (1.06 m/s). (a) Sequential solidification of the molten pool at the end of the melt track for laser powers of 190 and 340 W, respectively. (b) Recoil pressure on the molten pool at the keyhole for laser powers of 190 and 340 W, respectively. (c) The force diagram of the melt at the back of the keyhole at t = 750 μs in case B. (d) Temperature gradient at the solid–liquid interface of the molten pool at the moment the laser is deactivated in case A. (e) Temperature gradient at the solid–liquid interface of the molten pool at the moment the laser is deactivated in case B.

Revealing formation mechanism of end of processdepression in laser powder bed fusion by multiphysics meso-scale simulation

다중물리 메조 규모 시뮬레이션을 통해 레이저 분말층 융합에서 공정 종료의 함몰 형성 메커니즘 공개

Haodong Chen ^a,b, Xin Lin ^a,b,c, Yajing Sund, Shuhao Wang^a,b, Kunpeng Zhu ^a,b,c and Binbin Dan^a,b

To link to this article: https://doi.org/10.1080/17452759.2024.2326599

ABSTRACT

Unintended end-of-process depression (EOPD) commonly occurs in laser powder bed fusion (LPBF), leading to poor surface quality and lower fatigue strength, especially for many implants. In this study, a high-fidelity multi-physics meso-scale simulation model is developed to uncover the forming mechanism of this defect. A defect-process map of the EOPD phenomenon is obtained using this simulation model. It is found that the EOPD formation mechanisms are different under distinct regions of process parameters. At low scanning speeds in keyhole mode, the long-lasting recoil pressure and the large temperature gradient easily induce EOPD. While at high scanning speeds in keyhole mode, the shallow molten pool morphology and the large solidification rate allow the keyhole to evolve into an EOPD quickly. Nevertheless, in the conduction mode, the Marangoni effects along with a faster solidification rate induce EOPD. Finally, a ‘step’ variable power strategy is proposed to optimise the EOPD defects for the case with high volumetric energy density at low scanning speeds. This work provides a profound understanding and valuable insights into the quality control of LPBF fabrication.

의도하지 않은 공정 종료 후 함몰(EOPD)은 LPBF(레이저 분말층 융합)에서 흔히 발생하며, 특히 많은 임플란트의 경우 표면 품질이 떨어지고 피로 강도가 낮아집니다. 본 연구에서는 이 결함의 형성 메커니즘을 밝히기 위해 충실도가 높은 다중 물리학 메조 규모 시뮬레이션 모델을 개발했습니다.

이 시뮬레이션 모델을 사용하여 EOPD 현상의 결함 프로세스 맵을 얻습니다. EOPD 형성 메커니즘은 공정 매개변수의 별개 영역에서 서로 다른 것으로 밝혀졌습니다.

키홀 모드의 낮은 스캔 속도에서는 오래 지속되는 반동 압력과 큰 온도 구배로 인해 EOPD가 쉽게 유발됩니다. 키홀 모드에서 높은 스캐닝 속도를 유지하는 동안 얕은 용융 풀 형태와 큰 응고 속도로 인해 키홀이 EOPD로 빠르게 진화할 수 있습니다.

그럼에도 불구하고 전도 모드에서는 더 빠른 응고 속도와 함께 마랑고니 효과가 EOPD를 유발합니다. 마지막으로, 낮은 스캐닝 속도에서 높은 체적 에너지 밀도를 갖는 경우에 대해 EOPD 결함을 최적화하기 위한 ‘단계’ 가변 전력 전략이 제안되었습니다.

이 작업은 LPBF 제조의 품질 관리에 대한 심오한 이해와 귀중한 통찰력을 제공합니다.

References

[1] Zhang C, Li Z, Zhang J, et al. Additive manufacturing of magnesium matrix composites: comprehensive review of recent progress and research perspectives. J Mag
Alloys. 2023. doi:10.1016/j.jma.2023.02.005
[2] Webster S, Lin H, Carter III FM, et al. Physical mechanisms in hybrid additive manufacturing: a process design framework. J Mater Process Technol. 2022;291:117048. doi:10. 1016/j.jmatprotec.2021.117048
[3] Wang S, Ning J, Zhu L, et al. Role of porosity defects in metal 3D printing: formation mechanisms, impacts on properties and mitigation strategies. Mater Today. 2022. doi:10.1016/j.mattod.2022.08.014
[4] Wei C, Li L. Recent progress and scientific challenges in multi-material additive manufacturing via laser-based powder bed fusion. Virtual Phys Prototyp. 2021;16 (3):347–371. doi:10.1080/17452759.2021.1928520
[5] Lin X, Wang Q, Fuh JYH, et al. Motion feature based melt pool monitoring for selective laser melting process. J Mater Process Technol. 2022;303:117523. doi:10.1016/j. jmatprotec.2022.117523
[6] Gockel J, Sheridan L, Koerper B, et al. The influence of additive manufacturing processing parameters on surface roughness and fatigue life. Int J Fatigue. 2019;124:380–388. doi:10.1016/j.ijfatigue.2019.03.025
[7] Nicoletto G. Influence of rough as-built surfaces on smooth and notched fatigue behavior of L-PBF AlSi10Mg. Addit Manuf. 2020;34:101251. doi:10.1016/j. addma.2020.101251
[8] Spece H, Yu T, Law AW, et al. 3D printed porous PEEK created via fused filament fabrication for osteoconductive orthopaedic surfaces. J Mech Behav Biomed Mater. 2020;109:103850. doi:10.1115/1.0004270v
[9] Andrukhov O, Huber R, Shi B, et al. Proliferation, behavior, and differentiation of osteoblasts on surfaces of different microroughness. Dent Mater. 2016;32(11):1374–1384. doi:10.1016/j.dental.2016.08.217
[10] Dai N, Zhang LC, Zhang J, et al. Corrosion behavior of selective laser melted Ti-6Al-4 V alloy in NaCl solution. Corros Sci. 2016;102:484–489. doi:10.1016/j.corsci.2015. 10.041
[11] Li EL, Wang L, Yu AB, et al. A three-phase model for simulation of heat transfer and melt pool behaviour in laser powder bed fusion process. Powder Technol. 2021;381:298–312. doi:10.1016/j.powtec.2020.11.061
[12] Liao B, Xia RF, Li W, et al. 3D-printed ti6al4v scaffolds with graded triply periodic minimal surface structure for bone tissue engineering. J Mater Eng Perform. 2021;30:4993– 5004. doi:10.1007/s11665-021-05580-z
[13] Li E, Zhou Z, Wang L, et al. Melt pool dynamics and pores formation in multi-track studies in laser powder bed fusion process. Powder Technol. 2022;405:117533. doi:10.1016/j.powtec.2022.117533
[14] Guo L, Geng S, Gao X, et al. Numerical simulation of heat transfer and fluid flow during nanosecond pulsed laser processing of Fe78Si9B13 amorphous alloys. Int J Heat Mass Transfer. 2021;170:121003. doi:10.1016/j.ijheatma sstransfer.2021.121003
[15] Guo L, Li Y, Geng S, et al. Numerical and experimental analysis for morphology evolution of 6061 aluminum alloy during nanosecond pulsed laser cleaning. Surf Coat Technol. 2022;432:128056. doi:10.1016/j.surfcoat. 2021.128056
[16] Li S, Liu D, Mi H, et al. Numerical simulation on evolution process of molten pool and solidification characteristics of melt track in selective laser melting of ceramic powder. Ceram Int. 2022;48(13):18302–18315. doi:10. 1016/j.ceramint.2022.03.089
[17] Aboulkhair NT, Maskery I, Tuck C, et al. On the formation of AlSi10Mg single tracks and layers in selective laser melting: microstructure and nano-mechanical properties. J Mater Process Technol. 2016;230:88–98. doi:10.1016/j. jmatprotec.2015.11.016
[18] Thijs L, Kempen K, Kruth JP, et al. Fine-structured aluminium products with controllable texture by selective laser melting of pre-alloyed AlSi10Mg powder. Acta Mater. 2013;61(5):1809–1819. doi:10.1016/j.actamat.2012.11.052
[19] Qiu C, Adkins NJE, Attallah MM. Microstructure and tensile properties of selectively laser-melted and of HIPed laser-melted Ti–6Al–4 V. Mater Sci Eng A. 2013;578:230–239. doi:10.1016/j.msea.2013.04.099
[20] Kazemi Z, Soleimani M, Rokhgireh H, et al. Melting pool simulation of 316L samples manufactured by selective laser melting method, comparison with experimental results. Int J Therm Sci. 2022;176:107538. doi:10.1016/j. ijthermalsci.2022.107538
[21] Cao L. Workpiece-scale numerical simulations of SLM molten pool dynamic behavior of 316L stainless steel. Comput Math Appl. 2021;96:209–228. doi:10.1016/j. camwa.2020.04.020
[22] Liu B, Fang G, Lei L, et al. Predicting the porosity defects in selective laser melting (SLM) by molten pool geometry. Int J Mech Sci. 2022;228:107478. doi:10.1016/j.ijmecsci. 2022.107478
[23] Ur Rehman A, Pitir F, Salamci MU. Full-field mapping and flow quantification of melt pool dynamics in laser powder bed fusion of SS316L. Materials. 2021;14(21):6264. doi:10. 3390/ma14216264
[24] Chia HY, Wang L, Yan W. Influence of oxygen content on melt pool dynamics in metal additive manufacturing: high-fidelity modeling with experimental validation. Acta Mater. 2023;249:118824. doi:10.1016/j.actamat. 2023.118824
[25] Cheng B, Loeber L, Willeck H, et al. Computational investigation of melt pool process dynamics and pore formation in laser powder bed fusion. J Mater Eng Perform. 2019;28:6565–6578. doi:10.1007/s11665-019- 04435-y
[26] Li X, Guo Q, Chen L, et al. Quantitative investigation of gas flow, powder-gas interaction, and powder behavior under different ambient pressure levels in laser powder bed fusion. Int J Mach Tools Manuf. 2021;170:103797. doi:10.1016/j.ijmachtools.2021.103797
[27] Wu Y, Li M, Wang J, et al. Powder-bed-fusion additive manufacturing of molybdenum: process simulation, optimization, and property prediction. Addit Manuf. 2022;58:103069. doi:10.1016/j.addma.2022.103069
[28] Wu S, Yang Y, Huang Y, et al. Study on powder particle behavior in powder spreading with discrete element method and its critical implications for binder jetting additive manufacturing processes. Virtual Phys Prototyp. 2023;18(1):e2158877. doi:10.1080/17452759.2022.2158877
[29] Klassen A, Schakowsky T, Kerner C. Evaporation model for beam based additive manufacturing using free surface lattice Boltzmann methods. J Phys D Appl Phys. 2014;47 (27):275303. doi:10.1088/0022-3727/47/27/275303
[30] Cao L. Mesoscopic-scale numerical simulation including the influence of process parameters on slm single-layer multi-pass formation. Metall Mater Trans A. 2020;51:4130–4145. doi:10.1007/s11661-020-05831-z
[31] Zhuang JR, Lee YT, Hsieh WH, et al. Determination of melt pool dimensions using DOE-FEM and RSM with process window during SLM of Ti6Al4V powder. Opt Laser Technol. 2018;103:59–76. doi:10.1016/j.optlastec.2018. 01.013
[32] Li Y, Gu D. Thermal behavior during selective laser melting of commercially pure titanium powder: numerical simulation and experimental study. Addit Manuf. 2014;1–4:99–109. doi:10.1016/j.addma.2014.09.001
[33] Dai D, Gu D. Thermal behavior and densification mechanism during selective laser melting of copper matrix composites: simulation and experiments. Mater Des. 2014;55 (0):482–491. doi:10.1016/j.matdes.2013.10.006
[34] Wang S, Zhu L, Dun Y, et al. Multi-physics modeling of direct energy deposition process of thin-walled structures: defect analysis. Comput Mech. 2021;67:c1229– c1242. doi:10.1007/s00466-021-01992-9
[35] Wu J, Zheng J, Zhou H, et al. Molten pool behavior and its mechanism during selective laser melting of polyamide 6 powder: single track simulation and experiments. Mater Res Express. 2019;6. doi:10.1088/2053-1591/ab2747
[36] Cho JH, Farson DF, Milewski JO, et al. Weld pool flows during initial stages of keyhole formation in laser welding. J Phys D Appl Phys. 2009;42. doi:10.1088/0022- 3727/42/17/175502
[37] Sinha KN. Identification of a suitable volumetric heat source for modelling of selective laser melting of Ti6Al4V powder using numerical and experimental validation approach. Int J Adv Manuf Technol. 2018;99:2257–2270. doi:10.1007/s00170-018-2631-4
[38] Fu CH, Guo YB. Three-dimensional temperature gradient mechanism in selective laser melting of Ti-6Al-4V. J Manuf Sci Eng. 2014;136(6):061004. doi:10.1115/1.4028539
[39] Ansari P, Rehman AU, Pitir F, et al. Selective laser melting of 316 l austenitic stainless steel: detailed process understanding using multiphysics simulation and experimentation. Metals. 2021;11(7):1076. doi:10.3390/met11071076
[40] Zhao C, Shi B, Chen S, et al. Laser melting modes in metal powder bed fusion additive manufacturing. Rev Mod Phys. 2022;94(4):045002. doi:10.1103/revmodphys.94. 045002
[41] Bertoli US, Wolfer AJ, Matthews MJ, et al. On the limitations of volumetric energy density as a design parameter for selective laser melting. Mater Des. 2017;113:331–340. doi:10.1016/j.matdes.2016.10.037
[42] Dash A, Kamaraj A. Prediction of the shift in melting mode during additive manufacturing of 316L stainless steel. Mater Today Commun. 2023: 107238. doi:10.1016/j. mtcomm.2023.107238
[43] Majeed M, Khan HM, Rasheed I. Finite element analysis of melt pool thermal characteristics with passing laser in SLM process. Optik. 2019;194:163068. doi:10.1016/j.ijleo. 2019.163068

PDF 원문 보기

Schematic diagram of HP-LPBF melting process.

Modeling and numerical studies of high-precision laser powder bed fusion

Yi Wei ;Genyu Chen;Nengru Tao;Wei Zhou
https://doi.org/10.1063/5.0191504

In order to comprehensively reveal the evolutionary dynamics of the molten pool and the state of motion of the fluid during the high-precision laser powder bed fusion (HP-LPBF) process, this study aims to deeply investigate the specific manifestations of the multiphase flow, solidification phenomena, and heat transfer during the process by means of numerical simulation methods. Numerical simulation models of SS316L single-layer HP-LPBF formation with single and double tracks were constructed using the discrete element method and the computational fluid dynamics method. The effects of various factors such as Marangoni convection, surface tension, vapor recoil, gravity, thermal convection, thermal radiation, and evaporative heat dissipation on the heat and mass transfer in the molten pool have been paid attention to during the model construction process. The results show that the molten pool exhibits a “comet” shape, in which the temperature gradient at the front end of the pool is significantly larger than that at the tail end, with the highest temperature gradient up to 1.69 × 10⁸ K/s. It is also found that the depth of the second track is larger than that of the first one, and the process parameter window has been determined preliminarily. In addition, the application of HP-LPBF technology helps to reduce the surface roughness and minimize the forming size.

Topics

Heat transfer, Nonequilibrium thermodynamics, Solidification process, Computer simulation, Discrete element method, Lasers, Mass transfer, Fluid mechanics, Computational fluid dynamics, Multiphase flows

PDF Download

I. INTRODUCTION

Laser powder bed fusion (LPBF) has become a research hotspot in the field of additive manufacturing of metals due to its advantages of high-dimensional accuracy, good surface quality, high density, and high material utilization.^1,2 With the rapid development of electronics, medical, automotive, biotechnology, energy, communication, and optics, the demand for microfabrication technology is increasing day by day.³ High-precision laser powder bed fusion (HP-LPBF) is one of the key manufacturing technologies for tiny parts in the fields of electronics, medical, automotive, biotechnology, energy, communication, and optics because of its process characteristics such as small focal spot diameter, small powder particle size, and thin powder layup layer thickness.^4–13 Compared with LPBF, HP-LPBF has the significant advantages of smaller focal spot diameter, smaller powder particle size, and thinner layer thickness. These advantages make HP-LPBF perform better in producing micro-fine parts, high surface quality, and parts with excellent mechanical properties.

HP-LPBF is in the exploratory stage, and researchers have already done some exploratory studies on the focal spot diameter, the amount of defocusing, and the powder particle size. In order to explore the influence of changing the laser focal spot diameter on the LPBF process characteristics of the law, Wildman et al.¹⁴ studied five groups of different focal spot diameter LPBF forming 316L stainless steel (SS316L) processing effect, the smallest focal spot diameter of 26 μm, and the results confirm that changing the focal spot diameter can be achieved to achieve the energy control, so as to control the quality of forming. Subsequently, Mclouth et al.¹⁵ proposed the laser out-of-focus amount (focal spot diameter) parameter, which characterizes the distance between the forming plane and the laser focal plane. The laser energy density was controlled by varying the defocusing amount while keeping the laser parameters constant. Sample preparation at different focal positions was investigated, and their microstructures were characterized. The results show that the samples at the focal plane have finer microstructure than those away from the focal plane, which is the effect of higher power density and smaller focal spot diameter. In order to explore the influence of changing the powder particle size on the characteristics of the LPBF process, Qian et al.¹⁶ carried out single-track scanning simulations on powder beds with average powder particle sizes of 70 and 40 μm, respectively, and the results showed that the melt tracks sizes were close to each other under the same process parameters for the two particle-size distributions and that the molten pool of powder beds with small particles was more elongated and the edges of the melt tracks were relatively flat. In order to explore the superiority of HP-LPBF technology, Xu et al.¹⁷ conducted a comparative analysis of HP-LPBF and conventional LPBF of SS316L. The results showed that the average surface roughness of the top surface after forming by HP-LPBF could reach 3.40 μm. Once again, it was verified that HP-LPBF had higher forming quality than conventional LPBF. On this basis, Wei et al.⁶ comparatively analyzed the effects of different laser focal spot diameters on different powder particle sizes formed by LPBF. The results showed that the smaller the laser focal spot diameter, the fewer the defects on the top and side surfaces. The above research results confirm that reducing the laser focal spot diameter can obtain higher energy density and thus better forming quality.

LPBF involves a variety of complex systems and mechanisms, and the final quality of the part is influenced by a large number of process parameters.^18–24 Some research results have shown that there are more than 50 factors affecting the quality of the specimen. The influencing factors are mainly categorized into three main groups: (1) laser parameters, (2) powder parameters, and (3) equipment parameters, which interact with each other to determine the final specimen quality. With the continuous development of technologies such as computational materials science and computational fluid dynamics (CFD), the method of studying the influence of different factors on the forming quality of LPBF forming process has been shifted from time-consuming and laborious experimental characterization to the use of numerical simulation methods. As a result, more and more researchers are adopting this approach for their studies. Currently, numerical simulation studies on LPBF are mainly focused on the exploration of molten pool, temperature distribution, and residual stresses.

Finite element simulation based on continuum mechanics and free surface fluid flow modeling based on fluid dynamics are two common approaches to study the behavior of LPBF molten pool.^25–28 Finite element simulation focuses on the temperature and thermal stress fields, treats the powder bed as a continuum, and determines the molten pool size by plotting the elemental temperature above the melting point. In contrast, fluid dynamics modeling can simulate the 2D or 3D morphology of the metal powder pile and obtain the powder size and distribution by certain algorithms.²⁹ The flow in the molten pool is mainly affected by recoil pressure and the Marangoni effect. By simulating the molten pool formation, it is possible to predict defects, molten pool shape, and flow characteristics, as well as the effect of process parameters on the molten pool geometry.^30–34 In addition, other researchers have been conducted to optimize the laser processing parameters through different simulation methods and experimental data.^35–46 Crystal growth during solidification is studied to further understand the effect of laser parameters on dendritic morphology and solute segregation.^47–54 A multi-scale system has been developed to describe the fused deposition process during 3D printing, which is combined with the conductive heat transfer model and the dendritic solidification model.^55,56
Relevant scholars have adopted various different methods for simulation, such as sequential coupling theory,⁵⁷ Lagrangian and Eulerian thermal models,⁵⁸ birth–death element method,²⁵ and finite element method,⁵⁹ in order to reveal the physical phenomena of the laser melting process and optimize the process parameters. Luo et al.⁶⁰ compared the LPBF temperature field and molten pool under double ellipsoidal and Gaussian heat sources by ANSYS APDL and found that the diffusion of the laser energy in the powder significantly affects the molten pool size and the temperature field.
The thermal stresses obtained from the simulation correlate with the actual cracks,⁶¹ and local preheating can effectively reduce the residual stresses.⁶² A three-dimensional thermodynamic finite element model investigated the temperature and stress variations during laser-assisted fabrication and found that powder-to-solid conversion increases the temperature gradient, stresses, and warpage.⁶³ Other scholars have predicted residual stresses and part deflection for LPBF specimens and investigated the effects of deposition pattern, heat, laser power, and scanning strategy on residual stresses, noting that high-temperature gradients lead to higher residual stresses.^64–67

In short, the process of LPBF forming SS316L is extremely complex and usually involves drastic multi-scale physicochemical changes that will only take place on a very small scale. Existing literature employs DEM-based mesoscopic-scale numerical simulations to investigate the effects of process parameters on the molten pool dynamics of LPBF-formed SS316L. However, a few studies have been reported on the key mechanisms of heating and solidification, spatter, and convective behavior of the molten pool of HP-LPBF-formed SS316L with small laser focal spot diameters. In this paper, the geometrical properties of coarse and fine powder particles under three-dimensional conditions were first calculated using DEM. Then, numerical simulation models for single-track and double-track cases in the single-layer HP-LPBF forming SS316L process were developed at mesoscopic scale using the CFD method. The flow genesis of the melt in the single-track and double-track molten pools is discussed, and their 3D morphology and dimensional characteristics are discussed. In addition, the effects of laser process parameters, powder particle size, and laser focal spot diameter on the temperature field, characterization information, and defects in the molten pool are discussed.

II. MODELING

A. 3D powder bed modeling

HP-LPBF is an advanced processing technique for preparing target parts layer by layer stacking, the process of which involves repetitive spreading and melting of powders. In this process, both the powder spreading and the morphology of the powder bed are closely related to the results of the subsequent melting process, while the melted surface also affects the uniform distribution of the next layer of powder. For this reason, this chapter focuses on the modeling of the physical action during the powder spreading process and the theory of DEM to establish the numerical model of the powder bed, so as to lay a solid foundation for the accuracy of volume of fluid (VOF) and CFD.

1. DEM

DEM is a numerical technique for calculating the interaction of a large number of particles, which calculates the forces and motions of the spheres by considering each powder sphere as an independent unit. The motion of the powder particles follows the laws of classical Newtonian mechanics, including translational and rotational,^38,68–70 which are expressed as follows:��¨=��+∑��ij,

(1)��¨=∑�(�ij×�ij),

(2)

where �� is the mass of unit particle i in kg, ��¨ is the advective acceleration in m/s², And g is the gravitational acceleration in m/s². �ij is the force in contact with the neighboring particle � in N. �� is the rotational inertia of the unit particle � in kg · m². ��¨ is the unit particle � angular acceleration in rad/s². �ij is the vector pointing from unit particle � to the contact point of neighboring particle �⁠.

Equations (1) and (2) can be used to calculate the velocity and angular velocity variations of powder particles to determine their positions and velocities. A three-dimensional powder bed model of SS316L was developed using DEM. The powder particles are assumed to be perfect spheres, and the substrate and walls are assumed to be rigid. To describe the contact between the powder particles and between the particles and the substrate, a non-slip Hertz–Mindlin nonlinear spring-damping model⁷¹ was used with the following expression:�hz=��+��[(��ij−�eff��)−(��+�eff��)],

(3)

where �hz is the force calculated using the Hertzian in M. �� and �� are the radius of unit particles � and � in m, respectively. �� is the overlap size of the two powder particles in m. ��⁠, �� are the elastic constants in the normal and tangential directions, respectively. �ij is the unit vector connecting the centerlines of the two powder particles. �eff is the effective mass of the two powder particles in kg. �� and �� are the viscoelastic damping constants in the normal and tangential directions, respectively. �� and �� are the components of the relative velocities of the two powder particles. �� is the displacement vector between two spherical particles. The schematic diagram of overlapping powder particles is shown in Fig. 1.

FIG. 1.

VIEW LARGE DOWNLOAD SLIDE

Schematic diagram of overlapping powder particles.

Because the particle size of the powder used for HP-LPBF is much smaller than 100 μm, the effect of van der Waals forces must be considered. Therefore, the cohesive force �jkr of the Hertz–Mindlin model was used instead of van der Waals forces,⁷² with the following expression:�jkr=−4��0�*�1.5+4�*3�*�3,

(4)1�*=(1−��2)��+(1−��2)��,

(5)1�*=1��+1��,

(6)

where �* is the equivalent Young’s modulus in GPa; �* is the equivalent particle radius in m; �0 is the surface energy of the powder particles in J/m²; α is the contact radius in m; �� and �� are the Young’s modulus of the unit particles � and �⁠, respectively, in GPa; and �� and �� are the Poisson’s ratio of the unit particles � and �⁠, respectively.

2. Model building

Figure 2 shows a 3D powder bed model generated using DEM with a coarse powder geometry of 1000 × 400 × 30 μm³. The powder layer thickness is 30 μm, and the powder bed porosity is 40%. The average particle size of this spherical powder is 31.7 μm and is normally distributed in the range of 15–53 μm. The geometry of the fine powder was 1000 × 400 × 20 μm³, with a layer thickness of 20 μm, and the powder bed porosity of 40%. The average particle size of this spherical powder is 11.5 μm and is normally distributed in the range of 5–25 μm. After the 3D powder bed model is generated, it needs to be imported into the CFD simulation software for calculation, and the imported geometric model is shown in Fig. 3. This geometric model is mainly composed of three parts: protective gas, powder bed, and substrate. Under the premise of ensuring the accuracy of the calculation, the mesh size is set to 3 μm, and the total number of coarse powder meshes is 1 704 940. The total number of fine powder meshes is 3 982 250.

FIG. 2.

VIEW LARGE DOWNLOAD SLIDE

Three-dimensional powder bed model: (a) coarse powder, (b) fine powder.

FIG. 3.

VIEW LARGE DOWNLOAD SLIDE

Geometric modeling of the powder bed computational domain: (a) coarse powder, (b) fine powder.

B. Modeling of fluid mechanics simulation

In order to solve the flow, melting, and solidification problems involved in HP-LPBF molten pool, the study must follow the three governing equations of conservation of mass, conservation of energy, and conservation of momentum.⁷³ The VOF method, which is the most widely used in fluid dynamics, is used to solve the molten pool dynamics model.

1. VOF

VOF is a method for tracking the free interface between the gas and liquid phases on the molten pool surface. The core idea of the method is to define a volume fraction function F within each grid, indicating the proportion of the grid space occupied by the material, 0 ≤ F ≤ 1 in Fig. 4. Specifically, when F = 0, the grid is empty and belongs to the gas-phase region; when F = 1, the grid is completely filled with material and belongs to the liquid-phase region; and when 0 < F < 1, the grid contains free surfaces and belongs to the mixed region. The direction normal to the free surface is the direction of the fastest change in the volume fraction F (the direction of the gradient of the volume fraction), and the direction of the gradient of the volume fraction can be calculated from the values of the volume fractions in the neighboring grids.⁷⁴ The equations controlling the VOF are expressed as follows:𝛻��+�⋅(��→)=0,

(7)

where t is the time in s and �→ is the liquid velocity in m/s.

FIG. 4.

VIEW LARGE DOWNLOAD SLIDE

Schematic diagram of VOF.

The material parameters of the mixing zone are altered due to the inclusion of both the gas and liquid phases. Therefore, in order to represent the density of the mixing zone, the average density �¯ is used, which is expressed as follows:⁷²�¯=(1−�1)�gas+�1�metal,

(8)

where �1 is the proportion of liquid phase, �gas is the density of protective gas in kg/m³, and �metal is the density of metal in kg/m³.

2. Control equations and boundary conditions

Figure 5 is a schematic diagram of the HP-LPBF melting process. First, the laser light strikes a localized area of the material and rapidly heats up the area. Next, the energy absorbed in the region is diffused through a variety of pathways (heat conduction, heat convection, and surface radiation), and this process triggers complex phase transition phenomena (melting, evaporation, and solidification). In metals undergoing melting, the driving forces include surface tension and the Marangoni effect, recoil due to evaporation, and buoyancy due to gravity and uneven density. The above physical phenomena interact with each other and do not occur independently.

FIG. 5.

VIEW LARGE DOWNLOAD SLIDE

Schematic diagram of HP-LPBF melting process.

Laser heat sourceThe Gaussian surface heat source model is used as the laser heat source model with the following expression:�=2�0��2exp(−2�12��2),(9)where � is the heat flow density in W/m², �0 is the absorption rate of SS316L, �� is the radius of the laser focal spot in m, and �1 is the radial distance from the center of the laser focal spot in m. The laser focal spot can be used for a wide range of applications.
Energy absorptionThe formula for calculating the laser absorption �0 of SS316L is as follows:�0=0.365(�0[1+�0(�−20)]/�)0.5,(10)where �0 is the direct current resistivity of SS316L at 20 °C in Ω m, �0 is the resistance temperature coefficient in ppm/°C, � is the temperature in °C, and � is the laser wavelength in m.
Heat transferThe basic principle of heat transfer is conservation of energy, which is expressed as follows:𝛻𝛻𝛻�(��)��+�·(��→�)=�·(�0��)+��,(11)where � is the density of liquid phase SS316L in kg/m³, �� is the specific heat capacity of SS316L in J/(kg K), 𝛻� is the gradient operator, t is the time in s, T is the temperature in K, 𝛻�� is the temperature gradient, �→ is the velocity vector, �0 is the coefficient of thermal conduction of SS316L in W/(m K), and �� is the thermal energy dissipation term in the molten pool.
Molten pool flowThe following three conditions need to be satisfied for the molten pool to flow:
- Conservation of mass with the following expression:𝛻�·(��→)=0.(12)
- Conservation of momentum (Navier–Stokes equation) with the following expression:𝛻𝛻𝛻𝛻��→��+�(�→·�)�→=�·[−pI+�(��→+(��→)�)]+�,(13)where � is the pressure in Pa exerted on the liquid phase SS316L microelement, � is the unit matrix, � is the fluid viscosity in N s/m², and � is the volumetric force (gravity, atmospheric pressure, surface tension, vapor recoil, and the Marangoni effect).
- Conservation of energy, see Eq. (11)
Surface tension and the Marangoni effectThe effect of temperature on the surface tension coefficient is considered and set as a linear relationship with the following expression:�=�0−��dT(�−��),(14)where � is the surface tension of the molten pool at temperature T in N/m, �� is the melting temperature of SS316L in K, �0 is the surface tension of the molten pool at temperature �� in Pa, and σdσ/ dT is the surface tension temperature coefficient in N/(m K).In general, surface tension decreases with increasing temperature. A temperature gradient causes a gradient in surface tension that drives the liquid to flow, known as the Marangoni effect.
Metal vapor recoilAt higher input energy densities, the maximum temperature of the molten pool surface reaches the evaporation temperature of the material, and a gasification recoil pressure occurs vertically downward toward the molten pool surface, which will be the dominant driving force for the molten pool flow.⁷⁵ The expression is as follows:��=0.54�� exp ��−��0��,(15)where �� is the gasification recoil pressure in Pa, �� is the ambient pressure in kPa, �� is the latent heat of evaporation in J/kg, �0 is the gas constant in J/(mol K), T is the surface temperature of the molten pool in K, and T_e is the evaporation temperature in K.
Solid–liquid–gas phase transitionWhen the laser hits the powder layer, the powder goes through three stages: heating, melting, and solidification. During the solidification phase, mutual transformations between solid, liquid, and gaseous states occur. At this point, the latent heat of phase transition absorbed or released during the phase transition needs to be considered.⁶⁸ The phase transition is represented based on the relationship between energy and temperature with the following expression:�=��,(�<��),�(��)+�−��−��,(��<�<��)�(��)+(�−��)��,(��<�),,(16)where �� and �� are solid and liquid phase density, respectively, of SS316L in kg/m³. �� and �� unit volume of solid and liquid phase-specific heat capacity, respectively, of SS316L in J/(kg K). �� and ��⁠, respectively, are the solidification temperature and melting temperature of SS316L in K. �� is the latent heat of the phase transition of SS316L melting in J/kg.

3. Assumptions

The CFD model was computed using the commercial software package FLOW-3D.⁷⁶ In order to simplify the calculation and solution process while ensuring the accuracy of the results, the model makes the following assumptions:

It is assumed that the effects of thermal stress and material solid-phase thermal expansion on the calculation results are negligible.
The molten pool flow is assumed to be a Newtonian incompressible laminar flow, while the effects of liquid thermal expansion and density on the results are neglected.
It is assumed that the surface tension can be simplified to an equivalent pressure acting on the free surface of the molten pool, and the effect of chemical composition on the results is negligible.
Neglecting the effect of the gas flow field on the molten pool.
The mass loss due to evaporation of the liquid metal is not considered.
The influence of the plasma effect of the molten metal on the calculation results is neglected.

It is worth noting that the formulation of assumptions requires a trade-off between accuracy and computational efficiency. In the above models, some physical phenomena that have a small effect or high difficulty on the calculation results are simplified or ignored. Such simplifications make numerical simulations more efficient and computationally tractable, while still yielding accurate results.

4. Initial conditions

The preheating temperature of the substrate was set to 393 K, at which time all materials were in the solid state and the flow rate was zero.

5. Material parameters

The material used is SS316L and the relevant parameters required for numerical simulations are shown in Table I.^46,77,78

TABLE I.

SS316L-related parameters.

Property	Symbol	Value
Density of solid metal (kg/m³)	�metal	7980
Solid phase line temperature (K)	��	1658
Liquid phase line temperature (K)	��	1723
Vaporization temperature (K)	��	3090
Latent heat of melting (⁠ J/kg⁠)	��	2.60×105
Latent heat of evaporation (⁠ J/kg⁠)	��	7.45×106
Surface tension of liquid phase (N /m⁠)	�	1.60
Liquid metal viscosity (kg/m s)	��	6×10−3
Gaseous metal viscosity (kg/m s)	�gas	1.85×10−5
Temperature coefficient of surface tension (N/m K)	��/�T	0.80×10−3
Molar mass (⁠ kg/mol⁠)	M	0.05 593
Emissivity	�	0.26
Laser absorption	�0	0.35
Ambient pressure (kPa)	��	101 325
Ambient temperature (K)	�0	300
Stefan–Boltzmann constant (W/m² K⁴)	�	5.67×10−8
Thermal conductivity of metals (⁠ W/m K⁠)	�	24.55
Density of protective gas (kg/m³)	�gas	1.25
Coefficient of thermal expansion (/K)	��	16×10−6
Generalized gas constant (⁠ J/mol K⁠)	R	8.314

III. RESULTS AND DISCUSSION

With the objective of studying in depth the evolutionary patterns of single-track and double-track molten pool development, detailed observations were made for certain specific locations in the model, as shown in Fig. 6. In this figure, P1 and P2 represent the longitudinal tangents to the centers of the two melt tracks in the XZ plane, while L1 is the transverse profile in the YZ plane. The scanning direction is positive and negative along the X axis. Points A and B are the locations of the centers of the molten pool of the first and second melt tracks, respectively (x = 1.995 × 10⁻⁴, y = 5 × 10⁻⁷, and z = −4.85 × 10⁻⁵).

FIG. 6.

VIEW LARGE DOWNLOAD SLIDE

Schematic diagram of observation position.

A. Single-track simulation

A series of single-track molten pool simulation experiments were carried out in order to investigate the influence law of laser power as well as scanning speed on the HP-LPBF process. Figure 7 demonstrates the evolution of the 3D morphology and temperature field of the single-track molten pool in the time period of 50–500 μs under a laser power of 100 W and a scanning speed of 800 mm/s. The powder bed is in the natural cooling state. When t = 50 μs, the powder is heated by the laser heat and rapidly melts and settles to form the initial molten pool. This process is accompanied by partial melting of the substrate and solidification together with the melted powder. The molten pool rapidly expands with increasing width, depth, length, and temperature, as shown in Fig. 7(a). When t = 150 μs, the molten pool expands more obviously, and the temperature starts to transfer to the surrounding area, forming a heat-affected zone. At this point, the width of the molten pool tends to stabilize, and the temperature in the center of the molten pool has reached its peak and remains largely stable. However, the phenomenon of molten pool spatter was also observed in this process, as shown in Fig. 7(b). As time advances, when t = 300 μs, solidification begins to occur at the tail of the molten pool, and tiny ripples are produced on the solidified surface. This is due to the fact that the melt flows toward the region with large temperature gradient under the influence of Marangoni convection and solidifies together with the melt at the end of the bath. At this point, the temperature gradient at the front of the bath is significantly larger than at the end. While the width of the molten pool was gradually reduced, the shape of the molten pool was gradually changed to a “comet” shape. In addition, a slight depression was observed at the top of the bath because the peak temperature at the surface of the bath reached the evaporation temperature, which resulted in a recoil pressure perpendicular to the surface of the bath downward, creating a depressed region. As the laser focal spot moves and is paired with the Marangoni convection of the melt, these recessed areas will be filled in as shown in Fig. 7(c). It has been shown that the depressed regions are the result of the coupled effect of Marangoni convection, recoil pressure, and surface tension.⁷⁹ By t = 500 μs, the width and height of the molten pool stabilize and show a “comet” shape in Fig. 7(d).

FIG. 7.

VIEW LARGE DOWNLOAD SLIDE

Single-track molten pool process: (a) t = 50 ��⁠, (b) t = 150 ��⁠, (c) t = 300 ��⁠, (d) t = 500 ��⁠.

Figure 8 depicts the velocity vector diagram of the P1 profile in a single-track molten pool, the length of the arrows represents the magnitude of the velocity, and the maximum velocity is about 2.36 m/s. When t = 50 μs, the molten pool takes shape, and the velocities at the two ends of the pool are the largest. The variation of the velocities at the front end is especially more significant in Fig. 8(a). As the time advances to t = 150 μs, the molten pool expands rapidly, in which the velocity at the tail increases and changes more significantly, while the velocity at the front is relatively small. At this stage, the melt moves backward from the center of the molten pool, which in turn expands the molten pool area. The melt at the back end of the molten pool center flows backward along the edge of the molten pool surface and then converges along the edge of the molten pool to the bottom center, rising to form a closed loop. Similarly, a similar closed loop is formed at the front end of the center of the bath, but with a shorter path. However, a large portion of the melt in the center of the closed loop formed at the front end of the bath is in a nearly stationary state. The main cause of this melt flow phenomenon is the effect of temperature gradient and surface tension (the Marangoni effect), as shown in Figs. 8(b) and 8(e). This dynamic behavior of the melt tends to form an “elliptical” pool. At t = 300 μs, the tendency of the above two melt flows to close the loop is more prominent and faster in Fig. 8(c). When t = 500 μs, the velocity vector of the molten pool shows a stable trend, and the closed loop of melt flow also remains stable. With the gradual laser focal spot movement, the melt is gradually solidified at its tail, and finally, a continuous and stable single track is formed in Fig. 8(d).

FIG. 8.

VIEW LARGE DOWNLOAD SLIDE

Vector plot of single-track molten pool velocity in XZ longitudinal section: (a) t = 50 ��⁠, (b) t = 150 ��⁠, (c) t = 300 ��⁠, (d) t = 500 ��⁠, (e) molten pool flow.

In order to explore in depth the transient evolution of the molten pool, the evolution of the single-track temperature field and the melt flow was monitored in the YZ cross section. Figure 9(a) shows the state of the powder bed at the initial moment. When t = 250 μs, the laser focal spot acts on the powder bed and the powder starts to melt and gradually collects in the molten pool. At this time, the substrate will also start to melt, and the melt flow mainly moves in the downward and outward directions and the velocity is maximum at the edges in Fig. 9(b). When t = 300 μs, the width and depth of the molten pool increase due to the recoil pressure. At this time, the melt flows more slowly at the center, but the direction of motion is still downward in Fig. 9(c). When t = 350 μs, the width and depth of the molten pool further increase, at which time the intensity of the melt flow reaches its peak and the direction of motion remains the same in Fig. 9(d). When t = 400 μs, the melt starts to move upward, and the surrounding powder or molten material gradually fills up, causing the surface of the molten pool to begin to flatten. At this time, the maximum velocity of the melt is at the center of the bath, while the velocity at the edge is close to zero, and the edge of the melt starts to solidify in Fig. 9(e). When t = 450 μs, the melt continues to move upward, forming a convex surface of the melt track. However, the melt movement slows down, as shown in Fig. 9(f). When t = 500 μs, the melt further moves upward and its speed gradually becomes smaller. At the same time, the melt solidifies further, as shown in Fig. 9(g). When t = 550 μs, the melt track is basically formed into a single track with a similar “mountain” shape. At this stage, the velocity is close to zero only at the center of the molten pool, and the flow behavior of the melt is poor in Fig. 9(h). At t = 600 μs, the melt stops moving and solidification is rapidly completed. Up to this point, a single track is formed in Fig. 9(i). During the laser action on the powder bed, the substrate melts and combines with the molten state powder. The powder-to-powder fusion is like the convergence of water droplets, which are rapidly fused by surface tension. However, the fusion between the molten state powder and the substrate occurs driven by surface tension, and the molten powder around the molten pool is pulled toward the substrate (a wetting effect occurs), which ultimately results in the formation of a monolithic whole.^38,80,81

FIG. 9.

VIEW LARGE DOWNLOAD SLIDE

Evolution of single-track molten pool temperature and melt flow in the YZ cross section: (a) t = 0 ��⁠, (b) t = 250 ��⁠, (c) t = 300 ��⁠, (d) t = 350 ��⁠, (e) t = 400 ��⁠, (f) t = 450 ��⁠, (g) t = 500 ��⁠, (h) t = 550 ��⁠, (i) t = 600 ��⁠.

The wetting ability between the liquid metal and the solid substrate in the molten pool directly affects the degree of balling of the melt,^82,83 and the wetting ability can be measured by the contact angle of a single track in Fig. 10. A smaller value of contact angle represents better wettability. The contact angle α can be calculated by�=�1−�22,

(17)

where �1 and �2 are the contact angles of the left and right regions, respectively.

FIG. 10.

VIEW LARGE DOWNLOAD SLIDE

Schematic of contact angle.

Relevant studies have confirmed that the wettability is better at a contact angle α around or below 40°.⁸⁴ After measurement, a single-track contact angle α of about 33° was obtained under this process parameter, which further confirms the good wettability.

B. Double-track simulation

In order to deeply investigate the influence of hatch spacing on the characteristics of the HP-LPBF process, a series of double-track molten pool simulation experiments were systematically carried out. Figure 11 shows in detail the dynamic changes of the 3D morphology and temperature field of the double-track molten pool in the time period of 2050–2500 μs under the conditions of laser power of 100 W, scanning speed of 800 mm/s, and hatch spacing of 0.06 mm. By comparing the study with Fig. 7, it is observed that the basic characteristics of the 3D morphology and temperature field of the second track are similar to those of the first track. However, there are subtle differences between them. The first track exhibits a basically symmetric shape, but the second track morphology shows a slight deviation influenced by the difference in thermal diffusion rate between the solidified metal and the powder. Otherwise, the other characteristic information is almost the same as that of the first track. Figure 12 shows the velocity vector plot of the P2 profile in the double-track molten pool, with a maximum velocity of about 2.63 m/s. The melt dynamics at both ends of the pool are more stable at t = 2050 μs, where the maximum rate of the second track is only 1/3 of that of the first one. Other than that, the rest of the information is almost no significant difference from the characteristic information of the first track. Figure 13 demonstrates a detailed observation of the double-track temperature field and melts flow in the YZ cross section, and a comparative study with Fig. 9 reveals that the width of the second track is slightly wider. In addition, after the melt direction shifts from bottom to top, the first track undergoes four time periods (50 μs) to reach full solidification, while the second track takes five time periods. This is due to the presence of significant heat buildup in the powder bed after the forming of the first track, resulting in a longer dynamic time of the melt and an increased molten pool lifetime. In conclusion, the level of specimen forming can be significantly optimized by adjusting the laser power and hatch spacing.

FIG. 11.

VIEW LARGE DOWNLOAD SLIDE

Double-track molten pool process: (a) t = 2050 ��⁠, (b) t = 2150 ��⁠, (c) t = 2300 ��⁠, (d) t = 2500 ��⁠.

FIG. 12.

VIEW LARGE DOWNLOAD SLIDE

Vector plot of double-track molten pool velocity in XZ longitudinal section: (a) t = 2050 ��⁠, (b) t = 2150 ��⁠, (c) t = 2300 ��⁠, (d) t = 2500 ��⁠.

FIG. 13.

VIEW LARGE DOWNLOAD SLIDE

Evolution of double-track molten pool temperature and melt flow in the YZ cross section: (a) t = 2250 ��⁠, (b) t = 2300 ��⁠, (c) t = 2350 ��⁠, (d) t = 2400 ��⁠, (e) t = 2450 ��⁠, (f) t = 2500 ��⁠, (g) t = 2550 ��⁠, (h) t = 2600 ��⁠, (i) t = 2650 ��⁠.

In order to quantitatively detect the molten pool dimensions as well as the remolten region dimensions, the molten pool characterization information in Fig. 14 is constructed by drawing the boundary on the YZ cross section based on the isothermal surface of the liquid phase line. It can be observed that the heights of the first track and second track are basically the same, but the depth of the second track increases relative to the first track. The molten pool width is mainly positively correlated with the laser power as well as the scanning speed (the laser line energy density �⁠). However, the remelted zone width is negatively correlated with the hatch spacing (the overlapping ratio). Overall, the forming quality of the specimens can be directly influenced by adjusting the laser power, scanning speed, and hatch spacing.

FIG. 14.

VIEW LARGE DOWNLOAD SLIDE

Double-track molten pool characterization information on YZ cross section.

In order to study the variation rule of the temperature in the center of the molten pool with time, Fig. 15 demonstrates the temperature variation curves with time for two reference points, A and B. Among them, the red dotted line indicates the liquid phase line temperature of SS316L. From the figure, it can be seen that the maximum temperature at the center of the molten pool in the first track is lower than that in the second track, which is mainly due to the heat accumulation generated after passing through the first track. The maximum temperature gradient was calculated to be 1.69 × 10⁸ K/s. When the laser scanned the first track, the temperature in the center of the molten pool of the second track increased slightly. Similarly, when the laser scanned the second track, a similar situation existed in the first track. Since the temperature gradient in the second track is larger than that in the first track, the residence time of the liquid phase in the molten pool of the first track is longer than that of the second track.

FIG. 15.

VIEW LARGE DOWNLOAD SLIDE

Temperature profiles as a function of time for two reference points A and B.

C. Simulation analysis of molten pool under different process parameters

In order to deeply investigate the effects of various process parameters on the mesoscopic-scale temperature field, molten pool characteristic information and defects of HP-LPBF, numerical simulation experiments on mesoscopic-scale laser power, scanning speed, and hatch spacing of double-track molten pools were carried out.

1. Laser power

Figure 16 shows the effects of different laser power on the morphology and temperature field of the double-track molten pool at a scanning speed of 800 mm/s and a hatch spacing of 0.06 mm. When P = 50 W, a smaller molten pool is formed due to the lower heat generated by the Gaussian light source per unit time. This leads to a smaller track width, which results in adjacent track not lapping properly and the presence of a large number of unmelted powder particles, resulting in an increase in the number of defects, such as pores in the specimen. The surface of the track is relatively flat, and the depth is small. In addition, the temperature gradient before and after the molten pool was large, and the depression location appeared at the biased front end in Fig. 16(a). When P = 100 W, the surface of the track is flat and smooth with excellent lap. Due to the Marangoni effect, the velocity field of the molten pool is in the form of “vortex,” and the melt has good fluidity, and the maximum velocity reaches 2.15 m/s in Fig. 16(b). When P = 200 W, the heat generated by the Gaussian light source per unit time is too large, resulting in the melt rapidly reaching the evaporation temperature, generating a huge recoil pressure, forming a large molten pool, and the surface of the track is obviously raised. The melt movement is intense, especially the closed loop at the center end of the molten pool. At this time, the depth and width of the molten pool are large, leading to the expansion of the remolten region and the increased chance of the appearance of porosity defects in Fig. 16(c). The results show that at low laser power, the surface tension in the molten pool is dominant. At high laser power, recoil pressure is its main role.

FIG. 16.

VIEW LARGE DOWNLOAD SLIDE

Simulation results of double-track molten pool under different laser powers: (a) P = 50 W, (b) P = 100 W, (c) P = 200 W.

Table II shows the effect of different laser powers on the characteristic information of the double-track molten pool at a scanning speed of 800 mm/s and a hatch spacing of 0.06 mm. The negative overlapping ratio in the table indicates that the melt tracks are not lapped, and 26/29 indicates the melt depth of the first track/second track. It can be seen that with the increase in laser power, the melt depth, melt width, melt height, and remelted zone show a gradual increase. At the same time, the overlapping ratio also increases. Especially in the process of laser power from 50 to 200 W, the melting depth and melting width increased the most, which increased nearly 2 and 1.5 times, respectively. Meanwhile, the overlapping ratio also increases with the increase in laser power, which indicates that the melting and fusion of materials are better at high laser power. On the other hand, the dimensions of the molten pool did not change uniformly with the change of laser power. Specifically, the depth-to-width ratio of the molten pool increased from about 0.30 to 0.39 during the increase from 50 to 120 W, which further indicates that the effective heat transfer in the vertical direction is greater than that in the horizontal direction with the increase in laser power. This dimensional response to laser power is mainly affected by the recoil pressure and also by the difference in the densification degree between the powder layer and the metal substrate. In addition, according to the experimental results, the contact angle shows a tendency to increase and then decrease during the process of laser power increase, and always stays within the range of less than 33°. Therefore, in practical applications, it is necessary to select the appropriate laser power according to the specific needs in order to achieve the best processing results.

TABLE II.

Double-track molten pool characterization information at different laser powers.

Laser power (W)	Depth (μm)	Width (μm)	Height (μm)	Remolten region (μm)	Overlapping ratio (%)	Contact angle (°)
50	16	54	11	/	−10	23
100	26/29	74	14	18	23.33	33
200	37/45	116	21	52	93.33	28

2. Scanning speed

Figure 17 demonstrates the effect of different scanning speeds on the morphology and temperature field of the double-track molten pool at a laser power of 100 W and a hatch spacing of 0.06 mm. With the gradual increase in scanning speed, the surface morphology of the molten pool evolves from circular to elliptical. When � = 200 mm/s, the slow scanning speed causes the material to absorb too much heat, which is very easy to trigger the overburning phenomenon. At this point, the molten pool is larger and the surface morphology is uneven. This situation is consistent with the previously discussed scenario with high laser power in Fig. 17(a). However, when � = 1600 mm/s, the scanning speed is too fast, resulting in the material not being able to absorb sufficient heat, which triggers the powder particles that fail to melt completely to have a direct effect on the bonding of the melt to the substrate. At this time, the molten pool volume is relatively small and the neighboring melt track cannot lap properly. This result is consistent with the previously discussed case of low laser power in Fig. 17(b). Overall, the ratio of the laser power to the scanning speed (the line energy density �⁠) has a direct effect on the temperature field and surface morphology of the molten pool.

FIG. 17.

VIEW LARGE DOWNLOAD SLIDE

Simulation results of double-track molten pool under different scanning speed: (a) � = 200 mm/s, (b) � = 1600 mm/s.

Table III shows the effects of different scanning speed on the characteristic information of the double-track molten pool under the condition of laser power of 100 W and hatch spacing of 0.06 mm. It can be seen that the scanning speed has a significant effect on the melt depth, melt width, melt height, remolten region, and overlapping ratio. With the increase in scanning speed, the melt depth, melt width, melt height, remelted zone, and overlapping ratio show a gradual decreasing trend. Among them, the melt depth and melt width decreased faster, while the melt height and remolten region decreased relatively slowly. In addition, when the scanning speed was increased from 200 to 800 mm/s, the decreasing speeds of melt depth and melt width were significantly accelerated, while the decreasing speeds of overlapping ratio were relatively slow. When the scanning speed was further increased to 1600 mm/s, the decreasing speeds of melt depth and melt width were further accelerated, and the un-lapped condition of the melt channel also appeared. In addition, the contact angle increases and then decreases with the scanning speed, and both are lower than 33°. Therefore, when selecting the scanning speed, it is necessary to make reasonable trade-offs according to the specific situation, and take into account the factors of melt depth, melt width, melt height, remolten region, and overlapping ratio, in order to achieve the best processing results.

TABLE III.

Double-track molten pool characterization information at different scanning speeds.

Scanning speed (mm/s)	Depth (μm)	Width (μm)	Height (μm)	Remolten region (μm)	Overlapping ratio (%)	Contact angle (°)
200	55/68	182	19/32	124	203.33	22
1600	13	50	11	/	−16.67	31

3. Hatch spacing

Figure 18 shows the effect of different hatch spacing on the morphology and temperature field of the double-track molten pool under the condition of laser power of 100 W and scanning speed of 800 mm/s. The surface morphology and temperature field of the first track and second track are basically the same, but slightly different. The first track shows a basically symmetric morphology along the scanning direction, while the second track shows a slight offset due to the difference in the heat transfer rate between the solidified material and the powder particles. When the hatch spacing is too small, the overlapping ratio increases and the probability of defects caused by remelting phenomenon grows. When the hatch spacing is too large, the neighboring melt track cannot overlap properly, and the powder particles are not completely melted, leading to an increase in the number of holes. In conclusion, the ratio of the line energy density � to the hatch spacing (the volume energy density E) has a significant effect on the temperature field and surface morphology of the molten pool.

FIG. 18.

VIEW LARGE DOWNLOAD SLIDE

Simulation results of double-track molten pool under different hatch spacings: (a) H = 0.03 mm, (b) H = 0.12 mm.

Table IV shows the effects of different hatch spacing on the characteristic information of the double-track molten pool under the condition of laser power of 100 W and scanning speed of 800 mm/s. It can be seen that the hatch spacing has little effect on the melt depth, melt width, and melt height, but has some effect on the remolten region. With the gradual expansion of hatch spacing, the remolten region shows a gradual decrease. At the same time, the overlapping ratio also decreased with the increase in hatch spacing. In addition, it is observed that the contact angle shows a tendency to increase and then remain stable when the hatch spacing increases, which has a more limited effect on it. Therefore, trade-offs and decisions need to be made on a case-by-case basis when selecting the hatch spacing.

TABLE IV.

Double-track molten pool characterization information at different hatch spacings.

Hatch spacing (mm)	Depth (μm)	Width (μm)	Height (μm)	Remolten region (μm)	Overlapping ratio (%)	Contact angle (°)
0.03	25/27	82	14	59	173.33	30
0.12	26	78	14	/	−35	33

In summary, the laser power, scanning speed, and hatch spacing have a significant effect on the formation of the molten pool, and the correct selection of these three process parameters is crucial to ensure the forming quality. In addition, the melt depth of the second track is slightly larger than that of the first track at higher line energy density � and volume energy density E. This is mainly due to the fact that a large amount of heat accumulation is generated after the first track, forming a larger molten pool volume, which leads to an increase in the melt depth.

D. Simulation analysis of molten pool with powder particle size and laser focal spot diameter

Figure 19 demonstrates the effect of different powder particle sizes and laser focal spot diameters on the morphology and temperature field of the double-track molten pool under a laser power of 100 W, a scanning speed of 800 mm/s, and a hatch spacing of 0.06 mm. In the process of melting coarse powder with small laser focal spot diameter, the laser energy cannot completely melt the larger powder particles, resulting in their partial melting and further generating excessive pore defects. The larger powder particles tend to generate zigzag molten pool edges, which cause an increase in the roughness of the melt track surface. In addition, the molten pool is also prone to generate the present spatter phenomenon, which can directly affect the quality of forming. The volume of the formed molten pool is relatively small, while the melt depth, melt width, and melt height are all smaller relative to the fine powder in Fig. 19(a). In the process of melting fine powders with a large laser focal spot diameter, the laser energy is able to melt the fine powder particles sufficiently, even to the point of overmelting. This results in a large number of fine spatters being generated at the edge of the molten pool, which causes porosity defects in the melt track in Fig. 19(b). In addition, the maximum velocity of the molten pool is larger for large powder particle sizes compared to small powder particle sizes, which indicates that the temperature gradient in the molten pool is larger for large powder particle sizes and the melt motion is more intense. However, the size of the laser focal spot diameter has a relatively small effect on the melt motion. However, a larger focal spot diameter induces a larger melt volume with greater depth, width, and height. In conclusion, a small powder size helps to reduce the surface roughness of the specimen, and a small laser spot diameter reduces the minimum forming size of a single track.

FIG. 19.

VIEW LARGE DOWNLOAD SLIDE

Simulation results of double-track molten pool with different powder particle size and laser focal spot diameter: (a) focal spot = 25 μm, coarse powder, (b) focal spot = 80 μm, fine powder.

Table V shows the maximum temperature gradient at the reference point for different powder sizes and laser focal spot diameters. As can be seen from the table, the maximum temperature gradient is lower than that of HP-LPBF for both coarse powders with a small laser spot diameter and fine powders with a large spot diameter, a phenomenon that leads to an increase in the heat transfer rate of HP-LPBF, which in turn leads to a corresponding increase in the cooling rate and, ultimately, to the formation of finer microstructures.

TABLE V.

Maximum temperature gradient at the reference point for different powder particle sizes and laser focal spot diameters.

Laser power (W)	Scanning speed (mm/s)	Hatch spacing (mm)	Average powder size (μm)	Laser focal spot diameter (μm)	Maximum temperature gradient (×10⁷ K/s)
100	800	0.06	31.7	25	7.89
100	800	0.06	11.5	80	7.11

IV. CONCLUSIONS

In this study, the geometrical characteristics of 3D coarse and fine powder particles were first calculated using DEM and then numerical simulations of single track and double track in the process of forming SS316L from monolayer HP-LPBF at mesoscopic scale were developed using CFD method. The effects of Marangoni convection, surface tension, recoil pressure, gravity, thermal convection, thermal radiation, and evaporative heat dissipation on the heat and mass transfer in the molten pool were considered in this model. The effects of laser power, scanning speed, and hatch spacing on the dynamics of the single-track and double-track molten pools, as well as on other characteristic information, were investigated. The effects of the powder particle size on the molten pool were investigated comparatively with the laser focal spot diameter. The main conclusions are as follows:

The results show that the temperature gradient at the front of the molten pool is significantly larger than that at the tail, and the molten pool exhibits a “comet” morphology. At the top of the molten pool, there is a slightly concave region, which is the result of the coupling of Marangoni convection, recoil pressure, and surface tension. The melt flow forms two closed loops, which are mainly influenced by temperature gradients and surface tension. This special dynamic behavior of the melt tends to form an “elliptical” molten pool and an almost “mountain” shape in single-track forming.
The basic characteristics of the three-dimensional morphology and temperature field of the second track are similar to those of the first track, but there are subtle differences. The first track exhibits a basically symmetrical shape; however, due to the difference in thermal diffusion rates between the solidified metal and the powder, a slight asymmetry in the molten pool morphology of the second track occurs. After forming through the first track, there is a significant heat buildup in the powder bed, resulting in a longer dynamic time of the melt, which increases the life of the molten pool. The heights of the first track and second track remained essentially the same, but the depth of the second track was greater relative to the first track. In addition, the maximum temperature gradient was 1.69 × 10⁸ K/s during HP-LPBF forming.
At low laser power, the surface tension in the molten pool plays a dominant role. At high laser power, recoil pressure becomes the main influencing factor. With the increase of laser power, the effective heat transfer in the vertical direction is superior to that in the horizontal direction. With the gradual increase of scanning speed, the surface morphology of the molten pool evolves from circular to elliptical. In addition, the scanning speed has a significant effect on the melt depth, melt width, melt height, remolten region, and overlapping ratio. Too large or too small hatch spacing will lead to remelting or non-lap phenomenon, which in turn causes the formation of defects.
When using a small laser focal spot diameter, it is difficult to completely melt large powder particle sizes, resulting in partial melting and excessive porosity generation. At the same time, large powder particles produce curved edges of the molten pool, resulting in increased surface roughness of the melt track. In addition, spatter occurs, which directly affects the forming quality. At small focal spot diameters, the molten pool volume is relatively small, and the melt depth, the melt width, and the melt height are correspondingly small. Taken together, the small powder particle size helps to reduce surface roughness, while the small spot diameter reduces the forming size.

REFERENCES

S. L. Sing and W. Y. Yeong , “ Laser powder bed fusion for metal additive manufacturing: Perspectives on recent developments,” Virtual Phys. Prototyping. 15, 359–370 (2020).https://doi.org/10.1080/17452759.2020.1779999
Google ScholarCrossref
A. M. Khorasani , I. G. Jithin , J. K. Veetil , and A. H. Ghasemi , “ A review of technological improvements in laser-based powder bed fusion of metal printers,” Int. J. Adv. Manuf. Technol. 108, 191–209 (2020).https://doi.org/10.1007/s00170-020-05361-3
Google ScholarCrossref
Y. Qin , A. Brockett , Y. Ma , A. Razali , J. Zhao , C. Harrison , W. Pan , X. Dai , and D. Loziak , “ Micro-manufacturing: Research, technology outcomes and development issues,” Int. J. Adv. Manuf. Technol. 47, 821–837 (2010).https://doi.org/10.1007/s00170-009-2411-2
Google ScholarCrossref
B. Nagarajan , Z. Hu , X. Song , W. Zhai , and J. Wei , “ Development of micro selective laser melting: The state of the art and future perspectives,” Engineering. 5, 702–720 (2019).https://doi.org/10.1016/j.eng.2019.07.002
Google ScholarCrossref
Y. Wei , G. Chen , W. Li , Y. Zhou , Z. Nie , J. Xu , and W. Zhou , “ Micro selective laser melting of SS316L: Single tracks, defects, microstructures and thermal/mechanical properties,” Opt. Laser Technol. 145, 107469 (2022).https://doi.org/10.1016/j.optlastec.2021.107469
Google ScholarCrossref
Y. Wei , G. Chen , W. Li , M. Li , Y. Zhou , Z. Nie , and J. Xu , “ Process optimization of micro selective laser melting and comparison of different laser diameter for forming different powder,” Opt. Laser Technol. 150, 107953 (2022).https://doi.org/10.1016/j.optlastec.2022.107953
Google ScholarCrossref
H. Zhiheng , B. Nagarajan , X. Song , R. Huang , W. Zhai , and J. Wei , “ Formation of SS316L single tracks in micro selective laser melting: Surface, geometry, and defects,” Adv. Mater. Sci. Eng. 2019, 9451406.https://doi.org/10.1155/2019/9451406
Crossref
B. Nagarajan , Z. Hu , S. Gao , X. Song , R. Huang , M. Seita , and J. Wei , “ Effect of in-situ laser remelting on the microstructure of SS316L fabricated by micro selective laser melting,” in Advanced Surface Enhancement, edited by Sho Itoh and Shashwat Shukla , Lecture Notes in Mechanical Engineering ( Springer Singapore, Singapore, 2020), pp. 330–336.
Google ScholarCrossref
H. Zhiheng , B. Nagarajan , X. Song , R. Huang , W. Zhai , and J. Wei , “ Tailoring surface roughness of micro selective laser melted SS316L by in-situ laser remelting,” in Advanced Surface Enhancement, edited by Sho Itoh and Shashwat Shukla , Lecture Notes in Mechanical Engineering ( Springer Singapore, Singapore, 2020), pp. 337–343.
Google Scholar
J. Fu , Z. Hu , X. Song , W. Zhai , Y. Long , H. Li , and M. Fu , “ Micro selective laser melting of NiTi shape memory alloy: Defects, microstructures and thermal/mechanical properties,” Opt. Laser Technol. 131, 106374 (2020).https://doi.org/10.1016/j.optlastec.2020.106374
Google ScholarCrossref
E. Abele and M. Kniepkamp , “ Analysis and optimisation of vertical surface roughness in micro selective laser melting,” Surf. Topogr.: Metrol. Prop. 3, 034007 (2015).https://doi.org/10.1088/2051-672X/3/3/034007
Google ScholarCrossref
S. Qu , J. Ding , J. Fu , M. Fu , B. Zhang , and X. Song , “ High-precision laser powder bed fusion processing of pure copper,” Addit. Manuf. 48, 102417 (2021).https://doi.org/10.1016/j.addma.2021.102417
Google ScholarCrossref
Y. Wei , G. Chen , M. Li , W. Li , Y. Zhou , J. Xu , and Z. wei , “ High-precision laser powder bed fusion of 18Ni300 maraging steel and its SiC reinforcement composite materials,” J. Manuf. Process. 84, 750–763 (2022).https://doi.org/10.1016/j.jmapro.2022.10.049
Google ScholarCrossref
B. Liu , R. Wildman , T. Christopher , I. Ashcroft , and H. Richard , “ Investigation the effect of particle size distribution on processing parameters optimisation in selective laser melting process,” in 2011 International Solid Freeform Fabrication Symposium ( University of Texas at Austin, 2011).
Google Scholar
T. D. McLouth , G. E. Bean , D. B. Witkin , S. D. Sitzman , P. M. Adams , D. N. Patel , W. Park , J.-M. Yang , and R. J. Zaldivar , “ The effect of laser focus shift on microstructural variation of Inconel 718 produced by selective laser melting,” Mater. Des. 149, 205–213 (2018).https://doi.org/10.1016/j.matdes.2018.04.019
Google ScholarCrossref
Y. Qian , Y. Wentao , and L. Feng , “ Mesoscopic simulations of powder bed fusion: Research progresses and conditions,” Electromachining Mould 06, 46–52 (2017).https://doi.org/10.3969/j.issn.1009-279X.2017.06.012
Google Scholar
J. Fu , S. Qu , J. Ding , X. Song , and M. W. Fu , “ Comparison of the microstructure, mechanical properties and distortion of stainless Steel 316L fabricated by micro and conventional laser powder bed fusion,” Addit. Manuf. 44, 102067 (2021).https://doi.org/10.1016/j.addma.2021.102067
Google ScholarCrossref
N. T. Aboulkhair , I. Maskery , C. Tuck , I. Ashcroft , and N. M. Everitt , “ The microstructure and mechanical properties of selectively laser Melted AlSi10Mg: The effect of a conventional T6-like heat treatment,” Mater. Sci. Eng. A 667, 139–146 (2016).https://doi.org/10.1016/j.msea.2016.04.092
Google ScholarCrossref
S. Y. Chen , J. C. Huang , C. T. Pan , C. H. Lin , T. L. Yang , Y. S. Huang , C. H. Ou , L. Y. Chen , D. Y. Lin , H. K. Lin , T. H. Li , J. S. C. Jang , and C. C. Yang , “ Microstructure and mechanical properties of open-cell porous Ti-6Al-4V fabricated by selective laser melting,” J. Alloys Compd. 713, 248–254 (2017).https://doi.org/10.1016/j.jallcom.2017.04.190
Google ScholarCrossref
Y. Bai , Y. Yang , D. Wang , and M. Zhang , “ Influence mechanism of parameters process and mechanical properties evolution mechanism of Maraging steel 300 by selective laser melting,” Mater. Sci. Eng. A 703, 116–123 (2017).https://doi.org/10.1016/j.msea.2017.06.033
Google ScholarCrossref
Y. Bai , Y. Yang , Z. Xiao , M. Zhang , and D. Wang , “ Process optimization and mechanical property evolution of AlSiMg0.75 by selective laser melting,” Mater. Des. 140, 257–266 (2018).https://doi.org/10.1016/j.matdes.2017.11.045
Google ScholarCrossref
Y. Liu , M. Zhang , W. Shi , Y. Ma , and J. Yang , “ Study on performance optimization of 316L stainless steel parts by high-efficiency selective laser melting,” Opt. Laser Technol. 138, 106872 (2021).https://doi.org/10.1016/j.optlastec.2020.106872
Google ScholarCrossref
D. Gu , Y.-C. Hagedorn , W. Meiners , G. Meng , R. J. S. Batista , K. Wissenbach , and R. Poprawe , “ Densification behavior, microstructure evolution, and wear performance of selective laser melting processed commercially pure titanium,” Acta Mater. 60, 3849–3860 (2012).https://doi.org/10.1016/j.actamat.2012.04.006
Google ScholarCrossref
N. Read , W. Wang , K. Essa , and M. M. Attallah , “ Selective laser melting of AlSi10Mg alloy: Process optimisation and mechanical properties development,” Mater. Des. 65, 417–424 (2015).https://doi.org/10.1016/j.matdes.2014.09.044
Google ScholarCrossref
I. A. Roberts , C. J. Wang , R. Esterlein , M. Stanford , and D. J. Mynors , “ A three-dimensional finite element analysis of the temperature field during laser melting of metal powders in additive layer manufacturing,” Int. J. Mach. Tools Manuf. 49(12–13), 916–923 (2009).https://doi.org/10.1016/j.ijmachtools.2009.07.004
Google ScholarCrossref
K. Dai and L. Shaw , “ Finite element analysis of the effect of volume shrinkage during laser densification,” Acta Mater. 53(18), 4743–4754 (2005).https://doi.org/10.1016/j.actamat.2005.06.014
Google ScholarCrossref
K. Carolin , E. Attar , and P. Heinl , “ Mesoscopic simulation of selective beam melting processes,” J. Mater. Process. Technol. 211(6), 978–987 (2011).https://doi.org/10.1016/j.jmatprotec.2010.12.016
Google ScholarCrossref
F.-J. Gürtler , M. Karg , K.-H. Leitz , and M. Schmidt , “ Simulation of laser beam melting of steel powders using the three-dimensional volume of fluid method,” Phys. Procedia 41, 881–886 (2013).https://doi.org/10.1016/j.phpro.2013.03.162
Google ScholarCrossref
P. Meakin and R. Jullien , “ Restructuring effects in the rain model for random deposition,” J. Phys. France 48(10), 1651–1662 (1987).https://doi.org/10.1051/jphys:0198700480100165100
Google ScholarCrossref
J-m Wang , G-h Liu , Y-l Fang , and W-k Li , “ Marangoni effect in nonequilibrium multiphase system of material processing,” Rev. Chem. Eng. 32(5), 551–585 (2016).https://doi.org/10.1515/revce-2015-0067
Google ScholarCrossref
W. Ye , S. Zhang , L. L. Mendez , M. Farias , J. Li , B. Xu , P. Li , and Y. Zhang , “ Numerical simulation of the melting and alloying processes of elemental titanium and boron powders using selective laser alloying,” J. Manuf. Process. 64, 1235–1247 (2021).https://doi.org/10.1016/j.jmapro.2021.02.044
Google ScholarCrossref
U. S. Bertoli , A. J. Wolfer , M. J. Matthews , J.-P. R. Delplanque , and J. M. Schoenung , “ On the limitations of volumetric energy density as a design parameter for selective laser melting,” Mater. Des. 113, 331–340 (2017).https://doi.org/10.1016/j.matdes.2016.10.037
Google ScholarCrossref
W. E. King , H. D. Barth , V. M. Castillo , G. F. Gallegos , J. W. Gibbs , D. E. Hahn , C. Kamath , and A. M. Rubenchik , “ Observation of keyhole-mode laser melting in laser powder-bed fusion additive manufacturing,” J. Mater. Process. Technol. 214(12), 2915–2925 (2014).https://doi.org/10.1016/j.jmatprotec.2014.06.005
Google ScholarCrossref
L. Cao , “ Numerical simulation of the impact of laying powder on selective laser melting single-pass formation,” Int. J. Heat Mass Transfer 141, 1036–1048 (2019).https://doi.org/10.1016/j.ijheatmasstransfer.2019.07.053
Google ScholarCrossref
L. Huang , X. Hua , D. Wu , and F. Li , “ Numerical study of keyhole instability and porosity formation mechanism in laser welding of aluminum alloy and steel,” J. Mater. Process. Technol. 252, 421–431 (2018).https://doi.org/10.1016/j.jmatprotec.2017.10.011
Google ScholarCrossref
K. Q. Le , C. Tang , and C. H. Wong , “ On the study of keyhole-mode melting in selective laser melting process,” Int. J. Therm. Sci. 145, 105992 (2019).https://doi.org/10.1016/j.ijthermalsci.2019.105992
Google ScholarCrossref
J.-H. Cho and S.-J. Na , “ Theoretical analysis of keyhole dynamics in polarized laser drilling,” J. Phys. D: Appl. Phys. 40(24), 7638 (2007).https://doi.org/10.1088/0022-3727/40/24/007
Google ScholarCrossref
W. Ye , “ Mechanism analysis of selective laser melting and metallurgy process based on base element powder of titanium and boron,” Ph.D. dissertation ( Nanchang University, 2021).
Google Scholar
R. Ammer , M. Markl , U. Ljungblad , C. Körner , and U. Rüde , “ Simulating fast electron beam melting with a parallel thermal free surface lattice Boltzmann method,” Comput. Math. Appl. 67(2), 318–330 (2014).https://doi.org/10.1016/j.camwa.2013.10.001
Google ScholarCrossref
H. Chen , Q. Wei , S. Wen , Z. Li , and Y. Shi , “ Flow behavior of powder particles in layering process of selective laser melting: Numerical modeling and experimental verification based on discrete element method,” Int. J. Mach. Tools Manuf. 123, 146–159 (2017).https://doi.org/10.1016/j.ijmachtools.2017.08.004
Google ScholarCrossref
F. Verhaeghe , T. Craeghs , J. Heulens , and L. Pandelaers , “ A pragmatic model for selective laser melting with evaporation,” Acta Mater. 57(20), 6006–6012 (2009).https://doi.org/10.1016/j.actamat.2009.08.027
Google ScholarCrossref
C. H. Fu and Y. B. Guo , “ Three-dimensional temperature gradient mechanism in selective laser melting of Ti-6Al-4V,” J. Manuf. Sci. Eng. 136(6), 061004 (2014).https://doi.org/10.1115/1.4028539
Google ScholarCrossref
Y. Xiang , Z. Shuzhe , L. Junfeng , W. Zhengying , Y. Lixiang , and J. Lihao , “ Numerical simulation and experimental verification for selective laser single track melting forming of Ti6Al4V,” J. Zhejiang Univ. (Eng. Sci.) 53(11), 2102–2109 + 2117 (2019).https://doi.org/10.3785/j.issn.1008-973X.2019.11.007
Google Scholar
Q. He , H. Xia , J. Liu , X. Ao , and S. Lin , “ Modeling and numerical studies of selective laser melting: Multiphase flow, solidification and heat transfer,” Mater. Des. 196, 109115 (2020).https://doi.org/10.1016/j.matdes.2020.109115
Google ScholarCrossref
L. Cao , “ Mesoscopic-scale numerical simulation including the influence of process parameters on SLM single-layer multi-pass formation,” Metall. Mater. Trans. A 51, 4130–4145 (2020).https://doi.org/10.1007/s11661-020-05831-z
Google ScholarCrossref
L. Cao , “ Mesoscopic-scale numerical investigation including the influence of process parameters on LPBF multi-layer multi-path formation,” Comput. Model. Eng. Sci. 126(1), 5–23 (2021).https://doi.org/10.32604/cmes.2021.014693
Google ScholarCrossref
H. Yin and S. D. Felicelli , “ Dendrite growth simulation during solidification in the LENS process,” Acta Mater. 58(4), 1455–1465 (2010).https://doi.org/10.1016/j.actamat.2009.10.053
Google ScholarCrossref
P. Nie , O. A. Ojo , and Z. Li , “ Numerical modeling of microstructure evolution during laser additive manufacturing of a nickel-based superalloy,” Acta Mater. 77, 85–95 (2014).https://doi.org/10.1016/j.actamat.2014.05.039
Google ScholarCrossref
Z. Liu and H. Qi , “ Effects of substrate crystallographic orientations on crystal growth and microstructure formation in laser powder deposition of nickel-based superalloy,” Acta Mater. 87, 248–258 (2015).https://doi.org/10.1016/j.actamat.2014.12.046
Google ScholarCrossref
L. Wei , L. Xin , W. Meng , and H. Weidong , “ Cellular automaton simulation of the molten pool of laser solid forming process,” Acta Phys. Sin. 64(01), 018103–018363 (2015).https://doi.org/10.7498/aps.64.018103
Google ScholarCrossref
R. Acharya , J. A. Sharon , and A. Staroselsky , “ Prediction of microstructure in laser powder bed fusion process,” Acta Mater. 124, 360–371 (2017).https://doi.org/10.1016/j.actamat.2016.11.018
Google ScholarCrossref
M. R. Rolchigo and R. LeSar , “ Modeling of binary alloy solidification under conditions representative of additive manufacturing,” Comput. Mater. Sci. 150, 535–545 (2018).https://doi.org/10.1016/j.commatsci.2018.04.004
Google ScholarCrossref
S. Geng , P. Jiang , L. Guo , X. Gao , and G. Mi , “ Multi-scale simulation of grain/sub-grain structure evolution during solidification in laser welding of aluminum alloys,” Int. J. Heat Mass Transfer 149, 119252 (2020).https://doi.org/10.1016/j.ijheatmasstransfer.2019.119252
Google ScholarCrossref
W. L. Wang , W. Q. Liu , X. Yang , R. R. Xu , and Q. Y. Dai , “ Multi-scale simulation of columnar-to-equiaxed transition during laser selective melting of rare earth magnesium alloy,” J. Mater. Sci. Technol. 119, 11–24 (2022).https://doi.org/10.1016/j.jmst.2021.12.029
Google ScholarCrossref
Q. Xia , J. Yang , and Y. Li , “ On the conservative phase-field method with the N-component incompressible flows,” Phys. Fluids 35, 012120 (2023).https://doi.org/10.1063/5.0135490
Google ScholarCrossref
Q. Xia , G. Sun , J. Kim , and Y. Li , “ Multi-scale modeling and simulation of additive manufacturing based on fused deposition technique,” Phys. Fluids 35, 034116 (2023).https://doi.org/10.1063/5.0141316
Google ScholarCrossref
A. Hussein , L. Hao , C. Yan , and R. Everson , “ Finite element simulation of the temperature and stress fields in single layers built without-support in selective laser melting,” Mater. Des. 52, 638–647 (2013).https://doi.org/10.1016/j.matdes.2013.05.070
Google ScholarCrossref
J. Ding , P. Colegrove , J. Mehnen , S. Ganguly , P. M. Sequeira Almeida , F. Wang , and S. Williams , “ Thermo-mechanical analysis of wire and arc additive layer manufacturing process on large multi-layer parts,” Comput. Mater. Sci. 50(12), 3315–3322 (2011).https://doi.org/10.1016/j.commatsci.2011.06.023
Google ScholarCrossref
Y. Du , X. You , F. Qiao , L. Guo , and Z. Liu , “ A model for predicting the temperature field during selective laser melting,” Results Phys. 12, 52–60 (2019).https://doi.org/10.1016/j.rinp.2018.11.031
Google ScholarCrossref
X. Luo , M. Liu , L. Zhenhua , H. Li , and J. Shen , “ Effect of different heat-source models on calculated temperature field of selective laser melted 18Ni300,” Chin. J. Lasers 48(14), 1402005–1402062 (2021).https://doi.org/10.3788/CJL202148.1402005
Google ScholarCrossref
J. F. Li , L. Li , and F. H. Stott , “ Thermal stresses and their implication on cracking during laser melting of ceramic materials,” Acta Mater. 52(14), 4385–4398 (2004).https://doi.org/10.1016/j.actamat.2004.06.005
Google ScholarCrossref
P. Aggarangsi and J. L. Beuth , “ Localized preheating approaches for reducing residual stress in additive manufacturing,” paper presented at the 2006 International Solid Freeform Fabrication Symposium, The University of Texas in Austin on August 14–16, 2006.
K. Dai and L. Shaw , “ Thermal and mechanical finite element modeling of laser forming from metal and ceramic powders,” Acta Mater. 52(1), 69–80 (2004).https://doi.org/10.1016/j.actamat.2003.08.028
Google ScholarCrossref
A. H. Nickel , D. M. Barnett , and F. B. Prinz , “ Thermal stresses and deposition patterns in layered manufacturing,” Mater. Sci. Eng. A 317(1–2), 59–64 (2001).https://doi.org/10.1016/S0921-5093(01)01179-0
Google ScholarCrossref
M. F. Zaeh and G. Branner , “ Investigations on residual stresses and deformations in selective laser melting,” Prod. Eng. 4(1), 35–45 (2010).https://doi.org/10.1007/s11740-009-0192-y
Google ScholarCrossref
P. Bian , J. Shi , Y. Liu , and Y. Xie , “ Influence of laser power and scanning strategy on residual stress distribution in additively manufactured 316L steel,” Opt. Laser Technol. 132, 106477 (2020).https://doi.org/10.1016/j.optlastec.2020.106477
Google ScholarCrossref
B. M. Marques , C. M. Andrade , D. M. Neto , M. C. Oliveira , J. L. Alves , and L. F. Menezes , “ Numerical analysis of residual stresses in parts produced by selective laser melting process,” Procedia Manuf. 47, 1170–1177 (2020).https://doi.org/10.1016/j.promfg.2020.04.167
Google ScholarCrossref
W. Mu , “ Numerical simulation of SLM forming process and research and prediction of forming properties,” MA thesis ( Anhui Jianzhu University, 2022).
Google Scholar
Y. Zhang , “ Multi-scale multi-physics modeling of laser powder bed fusion process of metallic materials with experiment validation,” Ph.D. dissertation ( Purdue University, 2018).
Google Scholar
Y. Qian , “ Mesoscopic simulation studies of key processing issues for powder bed fusion technology,” Ph.D. dissertation ( Tsinghua University, 2019).
Google Scholar
N. V. Brilliantov , S. Frank , J.-M. Hertzsch , and T. Pöschel , “ Model for collisions in granular gases,” Phys. Rev. E 53(5), 5382–5392 (1996).https://doi.org/10.1103/PhysRevE.53.5382
Google ScholarCrossref
Z. Xiao , “ Research on microscale selective laser melting process of high strength pure copper specimens,” MA thesis ( Hunan University, 2022).
Google Scholar
Z. Li , K. Mukai , M. Zeze , and K. C. Mills , “ Determination of the surface tension of liquid stainless steel,” J. Mater. Sci. 40(9–10), 2191–2195 (2005).https://doi.org/10.1007/s10853-005-1931-x
Google ScholarCrossref
R. Scardovelli and S. Zaleski , “ Analytical relations connecting linear interfaces and volume fractions in rectangular grids,” J. Comput. Phys. 164(1), 228–237 (2000).https://doi.org/10.1006/jcph.2000.6567
Google ScholarCrossref
D.-W. Cho , W.-I. Cho , and S.-J. Na , “ Modeling and simulation of arc: Laser and hybrid welding process,” J. Manuf. Process. 16(1), 26–55 (2014).https://doi.org/10.1016/j.jmapro.2013.06.012
Google ScholarCrossref
76.Flow3D. Version 11.1.0: User Manual ( FlowScience, Santa Fe, NM, USA, 2015).
Y. Tian , L. Yang , D. Zhao , Y. Huang , and J. Pan , “ Numerical analysis of powder bed generation and single track forming for selective laser melting of ss316l stainless steel,” J. Manuf. Process. 58, 964–974 (2020).https://doi.org/10.1016/j.jmapro.2020.09.002
Google ScholarCrossref
C. Tang , K. Q. Le , and C. H. Wong , “ Physics of humping formation in laser powder bed fusion,” Int. J. Heat Mass Transfer 149, 119172 (2020).https://doi.org/10.1016/j.ijheatmasstransfer.2019.119172
Google ScholarCrossref
L. Cao , “ Mesoscopic-scale simulation of pore evolution during laser powder bed fusion process,” Comput. Mater. Sci. 179, 109686 (2020).https://doi.org/10.1016/j.commatsci.2020.109686
Google ScholarCrossref
R. Li , J. Liu , Y. Shi , W. Li , and W. Jiang , “ Balling behavior of stainless steel and nickel powder during selective laser melting process,” Int. J. Adv. Manuf. Technol. 59(9–12), 1025–1035 (2012).https://doi.org/10.1007/s00170-011-3566-1
Google ScholarCrossref
S. A. Khairallah and A. Anderson , “ Mesoscopic simulation model of selective laser melting of stainless steel powder,” J. Mater. Process. Technol. 214(11), 2627–2636 (2014).https://doi.org/10.1016/j.jmatprotec.2014.06.001
Google ScholarCrossref
J. Liu , D. Gu , H. Chen , D. Dai , and H. Zhang , “ Influence of substrate surface morphology on wetting behavior of tracks during selective laser melting of aluminum-based alloys,” J. Zhejiang Univ. Sci. A 19(2), 111–121 (2018).https://doi.org/10.1631/jzus.A1700599
Google ScholarCrossref
L. Li , J. Li , and T. Fan , “ Phase-field modeling of wetting and balling dynamics in powder bed fusion process,” Phys. Fluids 33, 042116 (2021).https://doi.org/10.1063/5.0046771
Google ScholarCrossref
X. Nie , Z. Hu , H. Zhu , Z. Hu , L. Ke , and X. Zeng , “ Analysis of processing parameters and characteristics of selective laser melted high strength Al-Cu-Mg alloys: from single tracks to cubic samples,” J. Mater. Process. Technol. 256, 69–77 (2018).https://doi.org/10.1016/j.jmatprotec.2018.01.030
Google ScholarCrossref

원본 바로가기

Figure 3. Computed contour of velocity magnitude (m/s) for Run 1 to Run 15.

FLOW-3D 소프트웨어를 이용한 유입구 및 배플 위치가 침전조 제거 효율에 미치는 영향

Ali Poorkarimi¹
Khaled Mafakheri²
Shahrzad Maleki²

Journal of Hydraulic Structures
J. Hydraul. Struct., 2023; 9(4): 76-87
DOI: 10.22055/jhs.2024.44817.1265

Abstract

중력에 의한 침전은 부유 물질을 제거하기 위해 물과 폐수 처리 공정에 널리 적용됩니다. 이 연구에서는 침전조의 제거 효율에 대한 입구 및 배플 위치의 영향을 간략하게 설명합니다. 실험은 CCD(중심복합설계) 방법론을 기반으로 수행되었습니다. 전산유체역학(CFD)은 유압 설계, 미래 발전소에 대한 계획 연구, 토목 유지 관리 및 공급 효율성과 관련된 복잡한 문제를 모델링하고 분석하는 데 광범위하게 사용됩니다. 본 연구에서는 입구 높이, 입구로부터 배플까지의 거리, 배플 높이의 다양한 조건에 따른 영향을 조사하였다. CCD 접근 방식을 사용하여 얻은 데이터를 분석하면 축소된 2차 모델이 R² = 0.77의 결정 계수로 부유 물질 제거를 예측할 수 있음이 나타났습니다. 연구 결과, 유입구와 배플의 부적절한 위치는 침전조의 효율에 부정적인 영향을 미칠 수 있음을 보여주었습니다. 입구 높이, 배플 거리, 배플 높이의 최적 값은 각각 0.87m, 0.77m, 0.56m였으며 제거 효율은 80.6%였습니다.

Sedimentation due to gravitation is applied widely in water and wastewater treatment processes to remove suspended solids. This study outlines the effect of the inlet and baffle position on the removal efficiency of sedimentation tanks. Experiments were carried out based on the central composite design (CCD) methodology. Computational fluid dynamics (CFD) is used extensively to model and analyze complex issues related to hydraulic design, planning studies for future generating stations, civil maintenance, and supply efficiency. In this study, the effect of different conditions of inlet elevation, baffle’s distance from the inlet, and baffle height were investigated. Analysis of the obtained data with a CCD approach illustrated that the reduced quadratic model can predict the suspended solids removal with a coefficient of determination of R² = 0.77. The results showed that the inappropriate position of the inlet and the baffle can have a negative effect on the efficiency of the sedimentation tank. The optimal values of inlet elevation, baffle distance, and baffle height were 0.87 m, 0.77 m, and 0.56 m respectively with 80.6% removal efficiency.

Keywords

Sedimentation tank, Particle removal, Central Composite Design, Computational
Fluid Dynamics, Flow-3D

References

Shahrokhi, M., F. Rostami, M.A. Md. Said, S.R.S. Yazdi, and Syafalni, (2013). Experimental
investigation of the influence of baffle position on the flow field, sediment concentration, and
efficiency of rectangular primary sedimentation tanks. Journal of Hydraulic Engineering,.
139(1): p. 88-94.
Shahrokhi, M., F. Rostami, M.A.M. Said, and S.R.S. Yazdi, (2012). The effect of number of
baffles on the improvement efficiency of primary sedimentation tanks. Applied Mathematical
Modelling,. 36(8): p. 3725-3735.
Borna, M., A. Janfeshan, E. Merufinia, and A. Asnaashari, (2014). Numerical simulations of
distribution and sediment transmission in pre-settled pools using Finite Volume Method and
comparison with experimental results. Journal of Civil Engineering and Urbanism,. 4(3): p.
287-292.
Rad, M.J., P.E. Firoozabadi, and F. Rostami, (2022). Numerical Investigation of the Effect
Dimensions of Rectangular Sedimentation Tanks on Its Hydraulic Efficiency Using Flow-3D
Software. Acta Technica Jaurinensis,. 15(4): p. 207-220.
Hirom, K. and T.T. Devi, (2022). Application of computational fluid dynamics in sedimentation
tank design and its recent developments: A review. Water, Air, & Soil Pollution,. 233: p. 1-
26.
Shahrokhi, M., F. Rostami, M.A.M. Said, S.-R. Sabbagh-Yazdi, S. Syafalni, and R. Abdullah,
(2012). The effect of baffle angle on primary sedimentation tank efficiency. Canadian Journal
of Civil Engineering,. 39(3): p. 293-303.
Tarpagkou, R. and A. Pantokratoras, (2014). The influence of lamellar settler in sedimentation
tanks for potable water treatment—A computational fluid dynamic study. Powder
Technology,. 268: p. 139-149.
Ekama, G. and P. Marais, (2004). Assessing the applicability of the 1D flux theory to full-scale
secondary settling tank design with a 2D hydrodynamic model. Water research,. 38(3): p. 495-
506.
Gharagozian, A., (1998). Circular secondary clarifier investigations using a numerical model.,
University of California, Los Angeles.
Shahrokhi, M., F. Rostami, and M.A.M. Said, (2013). Numerical modeling of baffle location
effects on the flow pattern of primary sedimentation tanks. Applied Mathematical Modelling,.
37(6): p. 4486-4496.
Razmi, A.M., R. Bakhtyar, B. Firoozabadi, and D.A. Barry, (2013). Experiments and
numerical modeling of baffle configuration effects on the performance of sedimentation tanks.
Canadian Journal of Civil Engineering,. 40(2): p. 140-150.
Liu, Y., P. Zhang, and W. Wei, (2016). Simulation of effect of a baffle on the flow patterns
and hydraulic efficiency in a sedimentation tank. Desalination and Water Treatment,. 57(54):
p. 25950-25959.
Saeedi, E., E. Behnamtalab, and S. Salehi Neyshabouri, (2020). Numerical simulation of baffle
effect on the performance of sedimentation basin. Water and environment journal,. 34(2): p.
212-222.
Miri, J.K., B. Aminnejad, and A. Zahiri, (2023). Numerical Study of Flow Pattern, Sediment
Field and Effect of the Arrangement of Guiding Blades (Baffles) on Sedimentation in PreSedimentation Basins by Numerical Models. Water Resources,. 50(1): p. 68-81.
Heydari, M.M., M. Rahbani, and S.M.M. Jamal, (2014). Experimental and numerical
investigations of baffle effect on the removal efficiency of sedimentation basin. Advances in
Environmental Biology,: p. 1015-1022.
Guo, H., S.J. Ki, S. Oh, Y.M. Kim, S. Wang, and J.H. Kim, (2017). Numerical simulation of
separation process for enhancing fine particle removal in tertiary sedimentation tank mounting
adjustable baffle. Chemical engineering science,. 158: p. 21-29.

PDF View

Lab-on-a-Chip 시스템의 혈류 역학에 대한 검토: 엔지니어링 관점

Review on Blood Flow Dynamics in Lab-on-a-Chip Systems: An Engineering Perspective

Bin-Jie Lai
,
Li-Tao Zhu
,
Zhe Chen*
,
Bo Ouyang*
, and
Zheng-Hong Luo*

Abstract

다양한 수송 메커니즘 하에서, “LOC(lab-on-a-chip)” 시스템에서 유동 전단 속도 조건과 밀접한 관련이 있는 혈류 역학은 다양한 수송 현상을 초래하는 것으로 밝혀졌습니다.

본 연구는 적혈구의 동적 혈액 점도 및 탄성 거동과 같은 점탄성 특성의 역할을 통해 LOC 시스템의 혈류 패턴을 조사합니다. 모세관 및 전기삼투압의 주요 매개변수를 통해 LOC 시스템의 혈액 수송 현상에 대한 연구는 실험적, 이론적 및 수많은 수치적 접근 방식을 통해 제공됩니다.

전기 삼투압 점탄성 흐름에 의해 유발되는 교란은 특히 향후 연구 기회를 위해 혈액 및 기타 점탄성 유체를 취급하는 LOC 장치의 혼합 및 분리 기능 향상에 논의되고 적용됩니다. 또한, 본 연구는 보다 정확하고 단순화된 혈류 모델에 대한 요구와 전기역학 효과 하에서 점탄성 유체 흐름에 대한 수치 연구에 대한 강조와 같은 LOC 시스템 하에서 혈류 역학의 수치 모델링의 문제를 식별합니다.

전기역학 현상을 연구하는 동안 제타 전위 조건에 대한 보다 실용적인 가정도 강조됩니다. 본 연구는 모세관 및 전기삼투압에 의해 구동되는 미세유체 시스템의 혈류 역학에 대한 포괄적이고 학제적인 관점을 제공하는 것을 목표로 한다.

원문 PDF 다운로드

KEYWORDS:

1. Introduction

1.1. Microfluidic Flow in Lab-on-a-Chip (LOC) Systems

Over the past several decades, the ability to control and utilize fluid flow patterns at microscales has gained considerable interest across a myriad of scientific and engineering disciplines, leading to growing interest in scientific research of microfluidics.

(1) Microfluidics, an interdisciplinary field that straddles physics, engineering, and biotechnology, is dedicated to the behavior, precise control, and manipulation of fluids geometrically constrained to a small, typically submillimeter, scale.

(2) The engineering community has increasingly focused on microfluidics, exploring different driving forces to enhance working fluid transport, with the aim of accurately and efficiently describing, controlling, designing, and applying microfluidic flow principles and transport phenomena, particularly for miniaturized applications.

(3) This attention has chiefly been fueled by the potential to revolutionize diagnostic and therapeutic techniques in the biomedical and pharmaceutical sectorsUnder various driving forces in microfluidic flows, intriguing transport phenomena have bolstered confidence in sustainable and efficient applications in fields such as pharmaceutical, biochemical, and environmental science. The “lab-on-a-chip” (LOC) system harnesses microfluidic flow to enable fluid processing and the execution of laboratory tasks on a chip-sized scale. LOC systems have played a vital role in the miniaturization of laboratory operations such as mixing, chemical reaction, separation, flow control, and detection on small devices, where a wide variety of fluids is adapted. Biological fluid flow like blood and other viscoelastic fluids are notably studied among the many working fluids commonly utilized by LOC systems, owing to the optimization in small fluid sample volumed, rapid response times, precise control, and easy manipulation of flow patterns offered by the system under various driving forces.

(4)The driving forces in blood flow can be categorized as passive or active transport mechanisms and, in some cases, both. Under various transport mechanisms, the unique design of microchannels enables different functionalities in driving, mixing, separating, and diagnosing blood and drug delivery in the blood.

(5) Understanding and manipulating these driving forces are crucial for optimizing the performance of a LOC system. Such knowledge presents the opportunity to achieve higher efficiency and reliability in addressing cellular level challenges in medical diagnostics, forensic studies, cancer detection, and other fundamental research areas, for applications of point-of-care (POC) devices.

(6)

1.2. Engineering Approach of Microfluidic Transport Phenomena in LOC Systems

Different transport mechanisms exhibit unique properties at submillimeter length scales in microfluidic devices, leading to significant transport phenomena that differ from those of macroscale flows. An in-depth understanding of these unique transport phenomena under microfluidic systems is often required in fluidic mechanics to fully harness the potential functionality of a LOC system to obtain systematically designed and precisely controlled transport of microfluids under their respective driving force. Fluid mechanics is considered a vital component in chemical engineering, enabling the analysis of fluid behaviors in various unit designs, ranging from large-scale reactors to separation units. Transport phenomena in fluid mechanics provide a conceptual framework for analytically and descriptively explaining why and how experimental results and physiological phenomena occur. The Navier–Stokes (N–S) equation, along with other governing equations, is often adapted to accurately describe fluid dynamics by accounting for pressure, surface properties, velocity, and temperature variations over space and time. In addition, limiting factors and nonidealities for these governing equations should be considered to impose corrections for empirical consistency before physical models are assembled for more accurate controls and efficiency. Microfluidic flow systems often deviate from ideal conditions, requiring adjustments to the standard governing equations. These deviations could arise from factors such as viscous effects, surface interactions, and non-Newtonian fluid properties from different microfluid types and geometrical layouts of microchannels. Addressing these nonidealities supports the refining of theoretical models and prediction accuracy for microfluidic flow behaviors.

The analytical calculation of coupled nonlinear governing equations, which describes the material and energy balances of systems under ideal conditions, often requires considerable computational efforts. However, advancements in computation capabilities, cost reduction, and improved accuracy have made numerical simulations using different numerical and modeling methods a powerful tool for effectively solving these complex coupled equations and modeling various transport phenomena. Computational fluid dynamics (CFD) is a numerical technique used to investigate the spatial and temporal distribution of various flow parameters. It serves as a critical approach to provide insights and reasoning for decision-making regarding the optimal designs involving fluid dynamics, even prior to complex physical model prototyping and experimental procedures. The integration of experimental data, theoretical analysis, and reliable numerical simulations from CFD enables systematic variation of analytical parameters through quantitative analysis, where adjustment to delivery of blood flow and other working fluids in LOC systems can be achieved.

Numerical methods such as the Finite-Difference Method (FDM), Finite-Element-Method (FEM), and Finite-Volume Method (FVM) are heavily employed in CFD and offer diverse approaches to achieve discretization of Eulerian flow equations through filling a mesh of the flow domain. A more in-depth review of numerical methods in CFD and its application for blood flow simulation is provided in Section 2.2.2.

1.3. Scope of the Review

In this Review, we explore and characterize the blood flow phenomena within the LOC systems, utilizing both physiological and engineering modeling approaches. Similar approaches will be taken to discuss capillary-driven flow and electric-osmotic flow (EOF) under electrokinetic phenomena as a passive and active transport scheme, respectively, for blood transport in LOC systems. Such an analysis aims to bridge the gap between physical (experimental) and engineering (analytical) perspectives in studying and manipulating blood flow delivery by different driving forces in LOC systems. Moreover, the Review hopes to benefit the interests of not only blood flow control in LOC devices but also the transport of viscoelastic fluids, which are less studied in the literature compared to that of Newtonian fluids, in LOC systems.

Section 2 examines the complex interplay between viscoelastic properties of blood and blood flow patterns under shear flow in LOC systems, while engineering numerical modeling approaches for blood flow are presented for assistance. Sections 3 and 4 look into the theoretical principles, numerical governing equations, and modeling methodologies for capillary driven flow and EOF in LOC systems as well as their impact on blood flow dynamics through the quantification of key parameters of the two driving forces. Section 5 concludes the characterized blood flow transport processes in LOC systems under these two forces. Additionally, prospective areas of research in improving the functionality of LOC devices employing blood and other viscoelastic fluids and potentially justifying mechanisms underlying microfluidic flow patterns outside of LOC systems are presented. Finally, the challenges encountered in the numerical studies of blood flow under LOC systems are acknowledged, paving the way for further research.

2. Blood Flow Phenomena

ARTICLE SECTIONS

Jump To

2.1. Physiological Blood Flow Behavior

Blood, an essential physiological fluid in the human body, serves the vital role of transporting oxygen and nutrients throughout the body. Additionally, blood is responsible for suspending various blood cells including erythrocytes (red blood cells or RBCs), leukocytes (white blood cells), and thrombocytes (blood platelets) in a plasma medium.Among the cells mentioned above, red blood cells (RBCs) comprise approximately 40–45% of the volume of healthy blood.

(7) An RBC possesses an inherent elastic property with a biconcave shape of an average diameter of 8 μm and a thickness of 2 μm. This biconcave shape maximizes the surface-to-volume ratio, allowing RBCs to endure significant distortion while maintaining their functionality.

(8,9) Additionally, the biconcave shape optimizes gas exchange, facilitating efficient uptake of oxygen due to the increased surface area. The inherent elasticity of RBCs allows them to undergo substantial distortion from their original biconcave shape and exhibits high flexibility, particularly in narrow channels.RBC deformability enables the cell to deform from a biconcave shape to a parachute-like configuration, despite minor differences in RBC shape dynamics under shear flow between initial cell locations. As shown in Figure 1(a), RBCs initiating with different resting shapes and orientations displaying display a similar deformation pattern

(10) in terms of its shape. Shear flow induces an inward bending of the cell at the rear position of the rim to the final bending position,

(11) resulting in an alignment toward the same position of the flow direction.

Figure 1. Images of varying deformation of RBCs and different dynamic blood flow behaviors. (a) The deforming shape behavior of RBCs at four different initiating positions under the same experimental conditions of a flow from left to right, (10) (b) RBC aggregation, (13) (c) CFL region. (18) Reproduced with permission from ref (10). Copyright 2011 Elsevier. Reproduced with permission from ref (13). Copyright 2022 The Authors, under the terms of the Creative Commons (CC BY 4.0) License https://creativecommons.org/licenses/by/4.0/. Reproduced with permission from ref (18). Copyright 2019 Elsevier.

The flexible property of RBCs enables them to navigate through narrow capillaries and traverse a complex network of blood vessels. The deformability of RBCs depends on various factors, including the channel geometry, RBC concentration, and the elastic properties of the RBC membrane.

(12) Both flexibility and deformability are vital in the process of oxygen exchange among blood and tissues throughout the body, allowing cells to flow in vessels even smaller than the original cell size prior to deforming.As RBCs serve as major components in blood, their collective dynamics also hugely affect blood rheology. RBCs exhibit an aggregation phenomenon due to cell to cell interactions, such as adhesion forces, among populated cells, inducing unique blood flow patterns and rheological behaviors in microfluidic systems. For blood flow in large vessels between a diameter of 1 and 3 cm, where shear rates are not high, a constant viscosity and Newtonian behavior for blood can be assumed. However, under low shear rate conditions (0.1 s

^–1) in smaller vessels such as the arteries and venules, which are within a diameter of 0.2 mm to 1 cm, blood exhibits non-Newtonian properties, such as shear-thinning viscosity and viscoelasticity due to RBC aggregation and deformability. The nonlinear viscoelastic property of blood gives rise to a complex relationship between viscosity and shear rate, primarily influenced by the highly elastic behavior of RBCs. A wide range of research on the transient behavior of the RBC shape and aggregation characteristics under varied flow circumstances has been conducted, aiming to obtain a better understanding of the interaction between blood flow shear forces from confined flows.

For a better understanding of the unique blood flow structures and rheological behaviors in microfluidic systems, some blood flow patterns are introduced in the following section.

2.1.1. RBC Aggregation

RBC aggregation is a vital phenomenon to be considered when designing LOC devices due to its impact on the viscosity of the bulk flow. Under conditions of low shear rate, such as in stagnant or low flow rate regions, RBCs tend to aggregate, forming structures known as rouleaux, resembling stacks of coins as shown in Figure 1(b).

(13) The aggregation of RBCs increases the viscosity at the aggregated region,

(14) hence slowing down the overall blood flow. However, when exposed to high shear rates, RBC aggregates disaggregate. As shear rates continue to increase, RBCs tend to deform, elongating and aligning themselves with the direction of the flow.

(15) Such a dynamic shift in behavior from the cells in response to the shear rate forms the basis of the viscoelastic properties observed in whole blood. In essence, the viscosity of the blood varies according to the shear rate conditions, which are related to the velocity gradient of the system. It is significant to take the intricate relationship between shear rate conditions and the change of blood viscosity due to RBC aggregation into account since various flow driving conditions may induce varied effects on the degree of aggregation.

2.1.2. Fåhræus-Lindqvist Effect

The Fåhræus–Lindqvist (FL) effect describes the gradual decrease in the apparent viscosity of blood as the channel diameter decreases.

(16) This effect is attributed to the migration of RBCs toward the central region in the microchannel, where the flow rate is higher, due to the presence of higher pressure and asymmetric distribution of shear forces. This migration of RBCs, typically observed at blood vessels less than 0.3 mm, toward the higher flow rate region contributes to the change in blood viscosity, which becomes dependent on the channel size. Simultaneously, the increase of the RBC concentration in the central region of the microchannel results in the formation of a less viscous region close to the microchannel wall. This region called the Cell-Free Layer (CFL), is primarily composed of plasma.

(17) The combination of the FL effect and the following CFL formation provides a unique phenomenon that is often utilized in passive and active plasma separation mechanisms, involving branched and constriction channels for various applications in plasma separation using microfluidic systems.

2.1.3. Cell-Free Layer Formation

In microfluidic blood flow, RBCs form aggregates at the microchannel core and result in a region that is mostly devoid of RBCs near the microchannel walls, as shown in Figure 1(c).

(18) The region is known as the cell-free layer (CFL). The CFL region is often known to possess a lower viscosity compared to other regions within the blood flow due to the lower viscosity value of plasma when compared to that of the aggregated RBCs. Therefore, a thicker CFL region composed of plasma correlates to a reduced apparent whole blood viscosity.

(19) A thicker CFL region is often established following the RBC aggregation at the microchannel core under conditions of decreasing the tube diameter. Apart from the dependence on the RBC concentration in the microchannel core, the CFL thickness is also affected by the volume concentration of RBCs, or hematocrit, in whole blood, as well as the deformability of RBCs. Given the influence CFL thickness has on blood flow rheological parameters such as blood flow rate, which is strongly dependent on whole blood viscosity, investigating CFL thickness under shear flow is crucial for LOC systems accounting for blood flow.

2.1.4. Plasma Skimming in Bifurcation Networks

The uneven arrangement of RBCs in bifurcating microchannels, commonly termed skimming bifurcation, arises from the axial migration of RBCs within flowing streams. This uneven distribution contributes to variations in viscosity across differing sizes of bifurcating channels but offers a stabilizing effect. Notably, higher flow rates in microchannels are associated with increased hematocrit levels, resulting in higher viscosity compared with those with lower flow rates. Parametric investigations on bifurcation angle,

(20) thickness of the CFL,

(21) and RBC dynamics, including aggregation and deformation,

(22) may alter the varying viscosity of blood and its flow behavior within microchannels.

2.2. Modeling on Blood Flow Dynamics

2.2.1. Blood Properties and Mathematical Models of Blood Rheology

Under different shear rate conditions in blood flow, the elastic characteristics and dynamic changes of the RBC induce a complex velocity and stress relationship, resulting in the incompatibility of blood flow characterization through standard presumptions of constant viscosity used for Newtonian fluid flow. Blood flow is categorized as a viscoelastic non-Newtonian fluid flow where constitutive equations governing this type of flow take into consideration the nonlinear viscometric properties of blood. To mathematically characterize the evolving blood viscosity and the relationship between the elasticity of RBC and the shear blood flow, respectively, across space and time of the system, a stress tensor (τ) defined by constitutive models is often coupled in the Navier–Stokes equation to account for the collective impact of the constant dynamic viscosity (η) and the elasticity from RBCs on blood flow.The dynamic viscosity of blood is heavily dependent on the shear stress applied to the cell and various parameters from the blood such as hematocrit value, plasma viscosity, mechanical properties of the RBC membrane, and red blood cell aggregation rate. The apparent blood viscosity is considered convenient for the characterization of the relationship between the evolving blood viscosity and shear rate, which can be defined by Casson’s law, as shown in eq 1.

𝜇=𝜏0𝛾˙+2𝜂𝜏0𝛾˙⎯⎯⎯⎯⎯⎯⎯√+𝜂�=�0�˙+2��0�˙+�

(1)where τ

₀ is the yield stress–stress required to initiate blood flow motion, η is the Casson rheological constant, and γ̇ is the shear rate. The value of Casson’s law parameters under blood with normal hematocrit level can be defined as τ

₀ = 0.0056 Pa and η = 0.0035 Pa·s.

(23) With the known property of blood and Casson’s law parameters, an approximation can be made to the dynamic viscosity under various flow condition domains. The Power Law model is often employed to characterize the dynamic viscosity in relation to the shear rate, since precise solutions exist for specific geometries and flow circumstances, acting as a fundamental standard for definition. The Carreau and Carreau–Yasuda models can be advantageous over the Power Law model due to their ability to evaluate the dynamic viscosity at low to zero shear rate conditions. However, none of the above-mentioned models consider the memory or other elastic behavior of blood and its RBCs. Some other commonly used mathematical models and their constants for the non-Newtonian viscosity property characterization of blood are listed in Table 1 below.

(24−26)Table 1. Comparison of Various Non-Newtonian Models for Blood Viscosity

(24−26)

Model	Non-Newtonian Viscosity	Parameters
Power Law	(2)	n = 0.61, k = 0.42
Carreau	(3)	μ₀ = 0.056 Pa·s, μ_∞ = 0.00345 Pa·s, λ = 3.1736 s, m = 2.406, a = 0.254
Walburn–Schneck	(4)	C₁ = 0.000797 Pa·s, C₂ = 0.0608 Pa·s, C₃ = 0.00499, C₄ = 14.585 g^–1, TPMA = 25 g/L
Carreau–Yasuda	(5)	μ₀ = 0.056 Pa·s, μ_∞ = 0.00345 Pa·s, λ = 1.902 s, n = 0.22, a = 1.25
Quemada	(6)	μ_p = 0.0012 Pa·s, k_∞ = 2.07, k₀ = 4.33, γ̇_c = 1.88 s^–1

The blood rheology is commonly known to be influenced by two key physiological factors, namely, the hematocrit value (H

_t) and the fibrinogen concentration (c

_f), with an average value of 42% and 0.252 gd·L

^–1, respectively. Particularly in low shear conditions, the presence of varying fibrinogen concentrations affects the tendency for aggregation and rouleaux formation, while the occurrence of aggregation is contingent upon specific levels of hematocrit.

(27) The study from Apostolidis et al.

(28) modifies the Casson model through emphasizing its reliance on hematocrit and fibrinogen concentration parameter values, owing to the extensive knowledge of the two physiological blood parameters.The viscoelastic response of blood is heavily dependent on the elasticity of the RBC, which is defined by the relationship between the deformation and stress relaxation from RBCs under a specific location of shear flow as a function of the velocity field. The stress tensor is usually characterized by constitutive equations such as the Upper-Convected Maxwell Model

(29) and the Oldroyd-B model

(30) to track the molecule effects under shear from different driving forces. The prominent non-Newtonian features, such as shear thinning and yield stress, have played a vital role in the characterization of blood rheology, particularly with respect to the evaluation of yield stress under low shear conditions. The nature of stress measurement in blood, typically on the order of 1 mPa, is challenging due to its low magnitude. The occurrence of the CFL complicates the measurement further due to the significant decrease in apparent viscosity near the wall over time and a consequential disparity in viscosity compared to the bulk region.In addition to shear thinning viscosity and yield stress, the formation of aggregation (rouleaux) from RBCs under low shear rates also contributes to the viscoelasticity under transient flow

(31) and thixotropy

(32) of whole blood. Given the difficulty in evaluating viscoelastic behavior of blood under low strain magnitudes and limitations in generalized Newtonian models, the utilization of viscoelastic models is advocated to encompass elasticity and delineate non-shear components within the stress tensor. Extending from the Oldroyd-B model, Anand et al.

(33) developed a viscoelastic model framework for adapting elasticity within blood samples and predicting non-shear stress components. However, to also address the thixotropic effects, the model developed by Horner et al.

(34) serves as a more comprehensive approach than the viscoelastic model from Anand et al. Thixotropy

(32) typically occurs from the structural change of the rouleaux, where low shear rate conditions induce rouleaux formation. Correspondingly, elasticity increases, while elasticity is more representative of the isolated RBCs, under high shear rate conditions. The model of Horner et al.

(34) considers the contribution of rouleaux to shear stress, taking into account factors such as the characteristic time for Brownian aggregation, shear-induced aggregation, and shear-induced breakage. Subsequent advancements in the model from Horner et al. often revolve around refining the three aforementioned key terms for a more substantial characterization of rouleaux dynamics. Notably, this has led to the recently developed mHAWB model

(35) and other model iterations to enhance the accuracy of elastic and viscoelastic contributions to blood rheology, including the recently improved model suggested by Armstrong et al.

(36)

2.2.2. Numerical Methods (FDM, FEM, FVM)

Numerical simulation has become increasingly more significant in analyzing the geometry, boundary layers of flow, and nonlinearity of hyperbolic viscoelastic flow constitutive equations. CFD is a powerful and efficient tool utilizing numerical methods to solve the governing hydrodynamic equations, such as the Navier–Stokes (N–S) equation, continuity equation, and energy conservation equation, for qualitative evaluation of fluid motion dynamics under different parameters. CFD overcomes the challenge of analytically solving nonlinear forms of differential equations by employing numerical methods such as the Finite-Difference Method (FDM), Finite-Element Method (FEM), and Finite-Volume Method (FVM) to discretize and solve the partial differential equations (PDEs), allowing for qualitative reproduction of transport phenomena and experimental observations. Different numerical methods are chosen to cope with various transport systems for optimization of the accuracy of the result and control of error during the discretization process.FDM is a straightforward approach to discretizing PDEs, replacing the continuum representation of equations with a set of finite-difference equations, which is typically applied to structured grids for efficient implementation in CFD programs.

(37) However, FDM is often limited to simple geometries such as rectangular or block-shaped geometries and struggles with curved boundaries. In contrast, FEM divides the fluid domain into small finite grids or elements, approximating PDEs through a local description of physics.

(38) All elements contribute to a large, sparse matrix solver. However, FEM may not always provide accurate results for systems involving significant deformation and aggregation of particles like RBCs due to large distortion of grids.

(39) FVM evaluates PDEs following the conservation laws and discretizes the selected flow domain into small but finite size control volumes, with each grid at the center of a finite volume.

(40) The divergence theorem allows the conversion of volume integrals of PDEs with divergence terms into surface integrals of surface fluxes across cell boundaries. Due to its conservation property, FVM offers efficient outcomes when dealing with PDEs that embody mass, momentum, and energy conservation principles. Furthermore, widely accessible software packages like the OpenFOAM toolbox

(41) include a viscoelastic solver, making it an attractive option for viscoelastic fluid flow modeling.

(42)

2.2.3. Modeling Methods of Blood Flow Dynamics

The complexity in the blood flow simulation arises from deformability and aggregation that RBCs exhibit during their interaction with neighboring cells under different shear rate conditions induced by blood flow. Numerical models coupled with simulation programs have been applied as a groundbreaking method to predict such unique rheological behavior exhibited by RBCs and whole blood. The conventional approach of a single-phase flow simulation is often applied to blood flow simulations within large vessels possessing a moderate shear rate. However, such a method assumes the properties of plasma, RBCs and other cellular components to be evenly distributed as average density and viscosity in blood, resulting in the inability to simulate the mechanical dynamics, such as RBC aggregation under high-shear flow field, inherent in RBCs. To accurately describe the asymmetric distribution of RBC and blood flow, multiphase flow simulation, where numerical simulations of blood flows are often modeled as two immiscible phases, RBCs and blood plasma, is proposed. A common assumption is that RBCs exhibit non-Newtonian behavior while the plasma is treated as a continuous Newtonian phase.Numerous multiphase numerical models have been proposed to simulate the influence of RBCs on blood flow dynamics by different assumptions. In large-scale simulations (above the millimeter range), continuum-based methods are wildly used due to their lower computational demands.

(43) Eulerian multiphase flow simulations offer the solution of a set of conservation equations for each separate phase and couple the phases through common pressure and interphase exchange coefficients. Xu et al.

(44) utilized the combined finite-discrete element method (FDEM) to replicate the dynamic behavior and distortion of RBCs subjected to fluidic forces, utilizing the Johnson–Kendall–Roberts model

(45) to define the adhesive forces of cell-to-cell interactions. The iterative direct-forcing immersed boundary method (IBM) is commonly employed in simulations of the fluid–cell interface of blood. This method effectively captures the intricacies of the thin and flexible RBC membranes within various external flow fields.

(46) The study by Xu et al.

(44) also adopts this approach to bridge the fluid dynamics and RBC deformation through IBM. Yoon and You utilized the Maxwell model to define the viscosity of the RBC membrane.

(47) It was discovered that the Maxwell model could represent the stress relaxation and unloading processes of the cell. Furthermore, the reduced flexibility of an RBC under particular situations such as infection is specified, which was unattainable by the Kelvin–Voigt model

(48) when compared to the Maxwell model in the literature. The Yeoh hyperplastic material model was also adapted to predict the nonlinear elasticity property of RBCs with FEM employed to discretize the RBC membrane using shell-type elements. Gracka et al.

(49) developed a numerical CFD model with a finite-volume parallel solver for multiphase blood flow simulation, where an updated Maxwell viscoelasticity model and a Discrete Phase Model are adopted. In the study, the adapted IBM, based on unstructured grids, simulates the flow behavior and shape change of the RBCs through fluid-structure coupling. It was found that the hybrid Euler–Lagrange (E–L) approach

(50) for the development of the multiphase model offered better results in the simulated CFL region in the microchannels.To study the dynamics of individual behaviors of RBCs and the consequent non-Newtonian blood flow, cell-shape-resolved computational models are often adapted. The use of the boundary integral method has become prevalent in minimizing computational expenses, particularly in the exclusive determination of fluid velocity on the surfaces of RBCs, incorporating the option of employing IBM or particle-based techniques. The cell-shaped-resolved method has enabled an examination of cell to cell interactions within complex ambient or pulsatile flow conditions

(51) surrounding RBC membranes. Recently, Rydquist et al.

(52) have looked to integrate statistical information from macroscale simulations to obtain a comprehensive overview of RBC behavior within the immediate proximity of the flow through introduction of respective models characterizing membrane shape definition, tension, bending stresses of RBC membranes.At a macroscopic scale, continuum models have conventionally been adapted for assessing blood flow dynamics through the application of elasticity theory and fluid dynamics. However, particle-based methods are known for their simplicity and adaptability in modeling complex multiscale fluid structures. Meshless methods, such as the boundary element method (BEM), smoothed particle hydrodynamics (SPH), and dissipative particle dynamics (DPD), are often used in particle-based characterization of RBCs and the surrounding fluid. By representing the fluid as discrete particles, meshless methods provide insights into the status and movement of the multiphase fluid. These methods allow for the investigation of cellular structures and microscopic interactions that affect blood rheology. Non-confronting mesh methods like IBM can also be used to couple a fluid solver such as FEM, FVM, or the Lattice Boltzmann Method (LBM) through membrane representation of RBCs. In comparison to conventional CFD methods, LBM has been viewed as a favorable numerical approach for solving the N–S equations and the simulation of multiphase flows. LBM exhibits the notable advantage of being amenable to high-performance parallel computing environments due to its inherently local dynamics. In contrast to DPD and SPH where RBC membranes are modeled as physically interconnected particles, LBM employs the IBM to account for the deformation dynamics of RBCs

(53,54) under shear flows in complex channel geometries.

(54,55) However, it is essential to acknowledge that the utilization of LBM in simulating RBC flows often entails a significant computational overhead, being a primary challenge in this context. Krüger et al.

(56) proposed utilizing LBM as a fluid solver, IBM to couple the fluid and FEM to compute the response of membranes to deformation under immersed fluids. This approach decouples the fluid and membranes but necessitates significant computational effort due to the requirements of both meshes and particles.Despite the accuracy of current blood flow models, simulating complex conditions remains challenging because of the high computational load and cost. Balachandran Nair et al.

(57) suggested a reduced order model of RBC under the framework of DEM, where the RBC is represented by overlapping constituent rigid spheres. The Morse potential force is adapted to account for the RBC aggregation exhibited by cell to cell interactions among RBCs at different distances. Based upon the IBM, the reduced-order RBC model is adapted to simulate blood flow transport for validation under both single and multiple RBCs with a resolved CFD-DEM solver.

(58) In the resolved CFD-DEM model, particle sizes are larger than the grid size for a more accurate computation of the surrounding flow field. A continuous forcing approach is taken to describe the momentum source of the governing equation prior to discretization, which is different from a Direct Forcing Method (DFM).

(59) As no body-conforming moving mesh is required, the continuous forcing approach offers lower complexity and reduced cost when compared to the DFM. Piquet et al.

(60) highlighted the high complexity of the DFM due to its reliance on calculating an additional immersed boundary flux for the velocity field to ensure its divergence-free condition.The fluid–structure interaction (FSI) method has been advocated to connect the dynamic interplay of RBC membranes and fluid plasma within blood flow such as the coupling of continuum–particle interactions. However, such methodology is generally adapted for anatomical configurations such as arteries

(61,62) and capillaries,

(63) where both the structural components and the fluid domain undergo substantial deformation due to the moving boundaries. Due to the scope of the Review being blood flow simulation within microchannels of LOC devices without deformable boundaries, the Review of the FSI method will not be further carried out.In general, three numerical methods are broadly used: mesh-based, particle-based, and hybrid mesh–particle techniques, based on the spatial scale and the fundamental numerical approach, mesh-based methods tend to neglect the effects of individual particles, assuming a continuum and being efficient in terms of time and cost. However, the particle-based approach highlights more of the microscopic and mesoscopic level, where the influence of individual RBCs is considered. A review from Freund et al.

(64) addressed the three numerical methodologies and their respective modeling approaches of RBC dynamics. Given the complex mechanics and the diverse levels of study concerning numerical simulations of blood and cellular flow, a broad spectrum of numerical methods for blood has been subjected to extensive review.

(64−70) Ye at al.

(65) offered an extensive review of the application of the DPD, SPH, and LBM for numerical simulations of RBC, while Rathnayaka et al.

(67) conducted a review of the particle-based numerical modeling for liquid marbles through drawing parallels to the transport of RBCs in microchannels. A comparative analysis between conventional CFD methods and particle-based approaches for cellular and blood flow dynamic simulation can be found under the review by Arabghahestani et al.

(66) Literature by Li et al.

(68) and Beris et al.

(69) offer an overview of both continuum-based models at micro/macroscales and multiscale particle-based models encompassing various length and temporal dimensions. Furthermore, these reviews deliberate upon the potential of coupling continuum-particle methods for blood plasma and RBC modeling. Arciero et al.

(70) investigated various modeling approaches encompassing cellular interactions, such as cell to cell or plasma interactions and the individual cellular phases. A concise overview of the reviews is provided in Table 2 for reference.

Table 2. List of Reviews for Numerical Approaches Employed in Blood Flow Simulation

Reference	Numerical methods
Li et al. (2013) (68)	Continuum-based modeling (BIM), particle-based modeling (LBM, LB-FE, SPH, DPD)
Freund (2014) (64)	RBC dynamic modeling (continuum-based modeling, complementary discrete microstructure modeling), blood flow dynamic modeling (FDM, IBM, LBM, particle-mesh methods, coupled boundary integral and mesh-based methods, DPD)
Ye et al. (2016) (65)	DPD, SPH, LBM, coupled IBM-Smoothed DPD
Arciero et al. (2017) (70)	LBM, IBM, DPD, conventional CFD Methods (FDM, FVM, FEM)
Arabghahestani et al. (2019) (66)	Particle-based methods (LBM, DPD, direct simulation Monte Carlo, molecular dynamics), SPH, conventional CFD methods (FDM, FVM, FEM)
Beris et al. (2021) (69)	DPD, smoothed DPD, IBM, LBM, BIM
Rathnayaka (2022) (67)	SPH, CG, LBM

3. Capillary Driven Blood Flow in LOC Systems

ARTICLE SECTIONS

Jump To

3.1. Capillary Driven Flow Phenomena

Capillary driven (CD) flow is a pivotal mechanism in passive microfluidic flow systems

(9) such as the blood circulation system and LOC systems.

(71) CD flow is essentially the movement of a liquid to flow against drag forces, where the capillary effect exerts a force on the liquid at the borders, causing a liquid–air meniscus to flow despite gravity or other drag forces. A capillary pressure drops across the liquid–air interface with surface tension in the capillary radius and contact angle. The capillary effect depends heavily on the interaction between the different properties of surface materials. Different values of contact angles can be manipulated and obtained under varying levels of surface wettability treatments to manipulate the surface properties, resulting in different CD blood delivery rates for medical diagnostic device microchannels. CD flow techniques are appealing for many LOC devices, because they require no external energy. However, due to the passive property of liquid propulsion by capillary forces and the long-term instability of surface treatments on channel walls, the adaptability of CD flow in geometrically complex LOC devices may be limited.

3.2. Theoretical and Numerical Modeling of Capillary Driven Blood Flow

3.2.1. Theoretical Basis and Assumptions of Microfluidic Flow

The study of transport phenomena regarding either blood flow driven by capillary forces or externally applied forces under microfluid systems all demands a comprehensive recognition of the significant differences in flow dynamics between microscale and macroscale. The fundamental assumptions and principles behind fluid transport at the microscale are discussed in this section. Such a comprehension will lay the groundwork for the following analysis of the theoretical basis of capillary forces and their role in blood transport in LOC systems.

At the macroscale, fluid dynamics are often strongly influenced by gravity due to considerable fluid mass. However, the high surface to volume ratio at the microscale shifts the balance toward surface forces (e.g., surface tension and viscous forces), much larger than the inertial force. This difference gives rise to transport phenomena unique to microscale fluid transport, such as the prevalence of laminar flow due to a very low Reynolds number (generally lower than 1). Moreover, the fluid in a microfluidic system is often assumed to be incompressible due to the small flow velocity, indicating constant fluid density in both space and time.Microfluidic flow behaviors are governed by the fundamental principles of mass and momentum conservation, which are encapsulated in the continuity equation and the Navier–Stokes (N–S) equation. The continuity equation describes the conservation of mass, while the N–S equation captures the spatial and temporal variations in velocity, pressure, and other physical parameters. Under the assumption of the negligible influence of gravity in microfluidic systems, the continuity equation and the Eulerian representation of the incompressible N–S equation can be expressed as follows:

∇·𝐮⇀=0∇·�⇀=0

(7)

−∇𝑝+𝜇∇2𝐮⇀+∇·𝝉⇀−𝐅⇀=0−∇�+�∇2�⇀+∇·�⇀−�⇀=0

(8)Here, p is the pressure, u is the fluid viscosity,

𝝉⇀�⇀ represents the stress tensor, and F is the body force exerted by external forces if present.

3.2.2. Theoretical Basis and Modeling of Capillary Force in LOC Systems

The capillary force is often the major driving force to manipulate and transport blood without an externally applied force in LOC systems. Forces induced by the capillary effect impact the free surface of fluids and are represented not directly in the Navier–Stokes equations but through the pressure boundary conditions of the pressure term p. For hydrophilic surfaces, the liquid generally induces a contact angle between 0° and 30°, encouraging the spread and attraction of fluid under a positive cos θ condition. For this condition, the pressure drop becomes positive and generates a spontaneous flow forward. A hydrophobic solid surface repels the fluid, inducing minimal contact. Generally, hydrophobic solids exhibit a contact angle larger than 90°, inducing a negative value of cos θ. Such a value will result in a negative pressure drop and a flow in the opposite direction. The induced contact angle is often utilized to measure the wall exposure of various surface treatments on channel walls where different wettability gradients and surface tension effects for CD flows are established. Contact angles between different interfaces are obtainable through standard values or experimental methods for reference.

(72)For the characterization of the induced force by the capillary effect, the Young–Laplace (Y–L) equation

(73) is widely employed. In the equation, the capillary is considered a pressure boundary condition between the two interphases. Through the Y–L equation, the capillary pressure force can be determined, and subsequently, the continuity and momentum balance equations can be solved to obtain the blood filling rate. Kim et al.

(74) studied the effects of concentration and exposure time of a nonionic surfactant, Silwet L-77, on the performance of a polydimethylsiloxane (PDMS) microchannel in terms of plasma and blood self-separation. The study characterized the capillary pressure force by incorporating the Y–L equation and further evaluated the effects of the changing contact angle due to different levels of applied channel wall surface treatments. The expression of the Y–L equation utilized by Kim et al.

(74) is as follows:

𝑃=−𝜎(cos𝜃b+cos𝜃tℎ+cos𝜃l+cos𝜃r𝑤)�=−�(cos⁡�b+cos⁡�tℎ+cos⁡�l+cos⁡�r�)

(9)where σ is the surface tension of the liquid and θ

_b, θ

_t, θ

_l, and θ

_r are the contact angle values between the liquid and the bottom, top, left, and right walls, respectively. A numerical simulation through Coventor software is performed to evaluate the dynamic changes in the filling rate within the microchannel. The simulation results for the blood filling rate in the microchannel are expressed at a specific time stamp, shown in Figure 2. The results portray an increasing instantaneous filling rate of blood in the microchannel following the decrease in contact angle induced by a higher concentration of the nonionic surfactant treated to the microchannel wall.

Figure 2. Numerical simulation of filling rate of capillary driven blood flow under various contact angle conditions at a specific timestamp. (74) Reproduced with permission from ref (74). Copyright 2010 Elsevier.

When in contact with hydrophilic or hydrophobic surfaces, blood forms a meniscus with a contact angle due to surface tension. The Lucas–Washburn (L–W) equation

(75) is one of the pioneering theoretical definitions for the position of the meniscus over time. In addition, the L–W equation provides the possibility for research to obtain the velocity of the blood formed meniscus through the derivation of the meniscus position. The L–W equation

(75) can be shown below:

𝐿(𝑡)=𝑅𝜎cos(𝜃)𝑡2𝜇⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯√�(�)=��⁡cos(�)�2�

(10)Here L(t) represents the distance of the liquid driven by the capillary forces. However, the generalized L–W equation solely assumes the constant physical properties from a Newtonian fluid rather than considering the non-Newtonian fluid behavior of blood. Cito et al.

(76) constructed an enhanced version of the L–W equation incorporating the power law to consider the RBC aggregation and the FL effect. The non-Newtonian fluid apparent viscosity under the Power Law model is defined as

𝜇=𝑘·(𝛾˙)𝑛−1�=�·(�˙)�−1

(11)where γ̇ is the strain rate tensor defined as

𝛾˙=12𝛾˙𝑖𝑗𝛾˙𝑗𝑖⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯√�˙=12�˙��˙��. The stress tensor term τ is computed as τ = μγ̇

_ij. The updated L–W equation by Cito

(76) is expressed as

𝐿(𝑡)=𝑅[(𝑛+13𝑛+1)(𝜎cos(𝜃)𝑅𝑘)1/𝑛𝑡]𝑛/𝑛+1�(�)=�[(�+13�+1)(�⁡cos(�)��)1/��]�/�+1

(12)where k is the flow consistency index and n is the power law index, respectively. The power law index, from the Power Law model, characterizes the extent of the non-Newtonian behavior of blood. Both the consistency and power law index rely on blood properties such as hematocrit, the appearance of the FL effect, the formation of RBC aggregates, etc. The updated L–W equation computes the location and velocity of blood flow caused by capillary forces at specified time points within the LOC devices, taking into account the effects of blood flow characteristics such as RBC aggregation and the FL effect on dynamic blood viscosity.Apart from the blood flow behaviors triggered by inherent blood properties, unique flow conditions driven by capillary forces that are portrayed under different microchannel geometries also hold crucial implications for CD blood delivery. Berthier et al.

(77) studied the spontaneous Concus–Finn condition, the condition to initiate the spontaneous capillary flow within a V-groove microchannel, as shown in Figure 3(a) both experimentally and numerically. Through experimental studies, the spontaneous Concus–Finn filament development of capillary driven blood flow is observed, as shown in Figure 3(b), while the dynamic development of blood flow is numerically simulated through CFD simulation.

Figure 3. (a) Sketch of the cross-section of Berthier’s V-groove microchannel, (b) experimental view of blood in the V-groove microchannel, (78) (c) illustration of the dynamic change of the extension of filament from FLOW 3D under capillary flow at three increasing time intervals. (78) Reproduced with permission from ref (78). Copyright 2014 Elsevier.

Berthier et al.

(77) characterized the contact angle needed for the initiation of the capillary driving force at a zero-inlet pressure, through the half-angle (α) of the V-groove geometry layout, and its relation to the Concus–Finn filament as shown below:

𝜃<𝜋2−𝛼sin𝛼1+2(ℎ2/𝑤)sin𝛼<cos𝜃{�<�2−�sin⁡�1+2(ℎ2/�)⁡sin⁡�<cos⁡�

(13)Three possible regimes were concluded based on the contact angle value for the initiation of flow and development of Concus–Finn filament:

𝜃>𝜃1𝜃1>𝜃>𝜃0𝜃0no SCFSCF without a Concus−Finn filamentSCF without a Concus−Finn filament{�>�1no SCF�1>�>�0SCF without a Concus−Finn filament�0SCF without a Concus−Finn filament

(14)Under Newton’s Law, the force balance with low Reynolds and Capillary numbers results in the neglect of inertial terms. The force balance between the capillary forces and the viscous force induced by the channel wall is proposed to derive the analytical fluid velocity. This relation between the two forces offers insights into the average flow velocity and the penetration distance function dependent on time. The apparent blood viscosity is defined by Berthier et al.

(78) through Casson’s law,

(23) given in eq 1. The research used the FLOW-3D program from Flow Science Inc. software, which solves transient, free-surface problems using the FDM in multiple dimensions. The Volume of Fluid (VOF) method

(79) is utilized to locate and track the dynamic extension of filament throughout the advancing interface within the channel ahead of the main flow at three progressing time stamps, as depicted in Figure 3(c).

4. Electro-osmotic Flow (EOF) in LOC Systems

ARTICLE SECTIONS

Jump To

The utilization of external forces, such as electric fields, has significantly broadened the possibility of manipulating microfluidic flow in LOC systems.

(80) Externally applied electric field forces induce a fluid flow from the movement of ions in fluid terms as the “electro-osmotic flow” (EOF).Unique transport phenomena, such as enhanced flow velocity and flow instability, induced by non-Newtonian fluids, particularly viscoelastic fluids, under EOF, have sparked considerable interest in microfluidic devices with simple or complicated geometries within channels.

(81) However, compared to the study of Newtonian fluids and even other electro-osmotic viscoelastic fluid flows, the literature focusing on the theoretical and numerical modeling of electro-osmotic blood flow is limited due to the complexity of blood properties. Consequently, to obtain a more comprehensive understanding of the complex blood flow behavior under EOF, theoretical and numerical studies of the transport phenomena in the EOF section will be based on the studies of different viscoelastic fluids under EOF rather than that of blood specifically. Despite this limitation, we believe these studies offer valuable insights that can help understand the complex behavior of blood flow under EOF.

4.1. EOF Phenomena

Electro-osmotic flow occurs at the interface between the microchannel wall and bulk phase solution. When in contact with the bulk phase, solution ions are absorbed or dissociated at the solid–liquid interface, resulting in the formation of a charge layer, as shown in Figure 4. This charged channel surface wall interacts with both negative and positive ions in the bulk sample, causing repulsion and attraction forces to create a thin layer of immobilized counterions, known as the Stern layer. The induced electric potential from the wall gradually decreases with an increase in the distance from the wall. The Stern layer potential, commonly termed the zeta potential, controls the intensity of the electrostatic interactions between mobile counterions and, consequently, the drag force from the applied electric field. Next to the Stern layer is the diffuse mobile layer, mainly composed of a mobile counterion. These two layers constitute the “electrical double layer” (EDL), the thickness of which is directly proportional to the ionic strength (concentration) of the bulk fluid. The relationship between the two parameters is characterized by a Debye length (λ

_D), expressed as

𝜆𝐷=𝜖𝑘B𝑇2(𝑍𝑒)2𝑐0⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯√��=��B�2(��)2�0

(15)where ϵ is the permittivity of the electrolyte solution, k

_B is the Boltzmann constant, T is the electron temperature, Z is the integer valence number, e is the elementary charge, and c

₀ is the ionic density.

Figure 4. Schematic diagram of an electro-osmotic flow in a microchannel with negative surface charge. (82) Reproduced with permission from ref (82). Copyright 2012 Woodhead Publishing.

When an electric field is applied perpendicular to the EDL, viscous drag is generated due to the movement of excess ions in the EDL. Electro-osmotic forces can be attributed to the externally applied electric potential (ϕ) and the zeta potential, the system wall induced potential by charged walls (ψ). As illustrated in Figure 4, the majority of ions in the bulk phase have a uniform velocity profile, except for a shear rate condition confined within an extremely thin Stern layer. Therefore, EOF displays a unique characteristic of a “near flat” or plug flow velocity profile, different from the parabolic flow typically induced by pressure-driven microfluidic flow (Hagen–Poiseuille flow). The plug-shaped velocity profile of the EOF possesses a high shear rate above the Stern layer.Overall, the EOF velocity magnitude is typically proportional to the Debye Length (λ

_D), zeta potential, and magnitude of the externally applied electric field, while a more viscous liquid reduces the EOF velocity.

4.2. Modeling on Electro-osmotic Viscoelastic Fluid Flow

4.2.1. Theoretical Basis of EOF Mechanisms

The EOF of an incompressible viscoelastic fluid is commonly governed by the continuity and incompressible N–S equations, as shown in eqs 7 and 8, where the stress tensor and the electrostatic force term are coupled. The electro-osmotic body force term F, representing the body force exerted by the externally applied electric force, is defined as

𝐹⇀=𝑝𝐸𝐸⇀�⇀=��⇀, where ρ

_E and

𝐸⇀�⇀ are the net electric charge density and the applied external electric field, respectively.Numerous models are established to theoretically study the externally applied electric potential and the system wall induced potential by charged walls. The following Laplace equation, expressed as eq 16, is generally adapted and solved to calculate the externally applied potential (ϕ).

∇2𝜙=0∇2�=0

(16)Ion diffusion under applied electric fields, together with mass transport resulting from convection and diffusion, transports ionic solutions in bulk flow under electrokinetic processes. The Nernst–Planck equation can describe these transport methods, including convection, diffusion, and electro-diffusion. Therefore, the Nernst–Planck equation is used to determine the distribution of the ions within the electrolyte. The electric potential induced by the charged channel walls follows the Poisson–Nernst–Plank (PNP) equation, which can be written as eq 17.

∇·[𝐷𝑖∇𝑛𝑖−𝑢⇀𝑛𝑖+𝑛𝑖𝐷𝑖𝑧𝑖𝑒𝑘𝑏𝑇∇(𝜙+𝜓)]=0∇·[��∇��−�⇀��+��∇(�+�)]=0

(17)where D

_i, n

_i, and z

_i are the diffusion coefficient, ionic concentration, and ionic valence of the ionic species I, respectively. However, due to the high nonlinearity and numerical stiffness introduced by different lengths and time scales from the PNP equations, the Poisson–Boltzmann (PB) model is often considered the major simplified method of the PNP equation to characterize the potential distribution of the EDL region in microchannels. In the PB model, it is assumed that the ionic species in the fluid follow the Boltzmann distribution. This model is typically valid for steady-state problems where charge transport can be considered negligible, the EDLs do not overlap with each other, and the intrinsic potentials are low. It provides a simplified representation of the potential distribution in the EDL region. The PB equation governing the EDL electric potential distribution is described as

∇2𝜓=(2𝑒𝑧𝑛0𝜀𝜀0)sinh(𝑧𝑒𝜓𝑘b𝑇)∇2�=(2��0��0)⁡sinh(��b�)

(18)where n

₀ is the ion bulk concentration, z is the ionic valence, and ε

₀ is the electric permittivity in the vacuum. Under low electric potential conditions, an even further simplified model to illustrate the EOF phenomena is the Debye–Hückel (DH) model. The DH model is derived by obtaining a charge density term by expanding the exponential term of the Boltzmann equation in a Taylor series.

4.2.2. EOF Modeling for Viscoelastic Fluids

Many studies through numerical modeling were performed to obtain a deeper understanding of the effect exhibited by externally applied electric fields on viscoelastic flow in microchannels under various geometrical designs. Bello et al.

(83) found that methylcellulose solution, a non-Newtonian polymer solution, resulted in stronger electro-osmotic mobility in experiments when compared to the predictions by the Helmholtz–Smoluchowski equation, which is commonly used to define the velocity of EOF of a Newtonian fluid. Being one of the pioneers to identify the discrepancies between the EOF of Newtonian and non-Newtonian fluids, Bello et al. attributed such discrepancies to the presence of a very high shear rate in the EDL, resulting in a change in the orientation of the polymer molecules. Park and Lee

(84) utilized the FVM to solve the PB equation for the characterization of the electric field induced force. In the study, the concept of fractional calculus for the Oldroyd-B model was adapted to illustrate the elastic and memory effects of viscoelastic fluids in a straight microchannel They observed that fluid elasticity and increased ratio of viscoelastic fluid contribution to overall fluid viscosity had a significant impact on the volumetric flow rate and sensitivity of velocity to electric field strength compared to Newtonian fluids. Afonso et al.

(85) derived an analytical expression for EOF of viscoelastic fluid between parallel plates using the DH model to account for a zeta potential condition below 25 mV. The study established the understanding of the electro-osmotic viscoelastic fluid flow under low zeta potential conditions. Apart from the electrokinetic forces, pressure forces can also be coupled with EOF to generate a unique fluid flow behavior within the microchannel. Sousa et al.

(86) analytically studied the flow of a standard viscoelastic solution by combining the pressure gradient force with an externally applied electric force. It was found that, at a near wall skimming layer and the outer layer away from the wall, macromolecules migrating away from surface walls in viscoelastic fluids are observed. In the study, the Phan-Thien Tanner (PTT) constitutive model is utilized to characterize the viscoelastic properties of the solution. The approach is found to be valid when the EDL is much thinner than the skimming layer under an enhanced flow rate. Zhao and Yang

(87) solved the PB equation and Carreau model for the characterization of the EOF mechanism and non-Newtonian fluid respectively through the FEM. The numerical results depict that, different from the EOF of Newtonian fluids, non-Newtonian fluids led to an increase of electro-osmotic mobility for shear thinning fluids but the opposite for shear thickening fluids.Like other fluid transport driving forces, EOF within unique geometrical layouts also portrays unique transport phenomena. Pimenta and Alves

(88) utilized the FVM to perform numerical simulations of the EOF of viscoelastic fluids considering the PB equation and the Oldroyd-B model, in a cross-slot and flow-focusing microdevices. It was found that electroelastic instabilities are formed due to the development of large stresses inside the EDL with streamlined curvature at geometry corners. Bezerra et al.

(89) used the FDM to numerically analyze the vortex formation and flow instability from an electro-osmotic non-Newtonian fluid flow in a microchannel with a nozzle geometry and parallel wall geometry setting. The PNP equation is utilized to characterize the charge motion in the EOF and the PTT model for non-Newtonian flow characterization. A constriction geometry is commonly utilized in blood flow adapted in LOC systems due to the change in blood flow behavior under narrow dimensions in a microchannel. Ji et al.

(90) recently studied the EOF of viscoelastic fluid in a constriction microchannel connected by two relatively big reservoirs on both ends (as seen in Figure 5) filled with the polyacrylamide polymer solution, a viscoelastic fluid, and an incompressible monovalent binary electrolyte solution KCl.

Figure 5. Schematic diagram of a negatively charged constriction microchannel connected to two reservoirs at both ends. An electro-osmotic flow is induced in the system by the induced potential difference between the anode and cathode. (90) Reproduced with permission from ref (90). Copyright 2021 The Authors, under the terms of the Creative Commons (CC BY 4.0) License https://creativecommons.org/licenses/by/4.0/.

In studying the EOF of viscoelastic fluids, the Oldroyd-B model is often utilized to characterize the polymeric stress tensor and the deformation rate of the fluid. The Oldroyd-B model is expressed as follows:

𝜏=𝜂p𝜆(𝐜−𝐈)�=�p�(�−�)

(19)where η

_p, λ, c, and I represent the polymer dynamic viscosity, polymer relaxation time, symmetric conformation tensor of the polymer molecules, and the identity matrix, respectively.A log-conformation tensor approach is taken to prevent convergence difficulty induced by the viscoelastic properties. The conformation tensor (c) in the polymeric stress tensor term is redefined by a new tensor (Θ) based on the natural logarithm of the c. The new tensor is defined as

Θ=ln(𝐜)=𝐑ln(𝚲)𝐑Θ=ln(�)=�⁡ln(�)�

(20)in which Λ is the diagonal matrix and R is the orthogonal matrix.Under the new conformation tensor, the induced EOF of a viscoelastic fluid is governed by the continuity and N–S equations adapting the Oldroyd-B model, which is expressed as

∂𝚯∂𝑡+𝐮·∇𝚯=𝛀Θ−ΘΩ+2𝐁+1𝜆(eΘ−𝐈)∂�∂�+�·∇�=�Θ−ΘΩ+2�+1�(eΘ−�)

(21)where Ω and B represent the anti-symmetric matrix and the symmetric traceless matrix of the decomposition of the velocity gradient tensor ∇u, respectively. The conformation tensor can be recovered by c = exp(Θ). The PB model and Laplace equation are utilized to characterize the charged channel wall induced potential and the externally applied potential.The governing equations are numerically solved through the FVM by RheoTool,

(42) an open-source viscoelastic EOF solver on the OpenFOAM platform. A SIMPLEC (Semi-Implicit Method for Pressure Linked Equations-Consistent) algorithm was applied to solve the velocity-pressure coupling. The pressure field and velocity field were computed by the PCG (Preconditioned Conjugate Gradient) solver and the PBiCG (Preconditioned Biconjugate Gradient) solver, respectively.Ranging magnitudes of an applied electric field or fluid concentration induce both different streamlines and velocity magnitudes at various locations and times of the microchannel. In the study performed by Ji et al.,

(90) notable fluctuation of streamlines and vortex formation is formed at the upper stream entrance of the constriction as shown in Figure 6(a) and (b), respectively, due to the increase of electrokinetic effect, which is seen as a result of the increase in polymeric stress (τ

_xx).

(90) The contraction geometry enhances the EOF velocity within the constriction channel under high E

_app condition (600 V/cm). Such phenomena can be attributed to the dependence of electro-osmotic viscoelastic fluid flow on the system wall surface and bulk fluid properties.

(91)

Figure 6. Schematic diagram of vortex formation and streamlines of EOF depicting flow instability at (a) 1.71 s and (b) 1.75 s. Spatial distribution of the elastic normal stress at (c) high E_app condition. Streamline of an electro-osmotic flow under E_app of 600 V/cm (90) for (d) non-Newtonian and (e) Newtonian fluid through a constriction geometry. Reproduced with permission from ref (90). Copyright 2021 The Authors, under the terms of the Creative Commons (CC BY 4.0) License https://creativecommons.org/licenses/by/4.0/.

As elastic normal stress exceeds the local shear stress, flow instability and vortex formation occur. The induced elastic stress under EOF not only enhances the instability of the flow but often generates an irregular secondary flow leading to strong disturbance.

(92) It is also vital to consider the effect of the constriction layout of microchannels on the alteration of the field strength within the system. The contraction geometry enhances a larger electric field strength compared with other locations of the channel outside the constriction region, resulting in a higher velocity gradient and stronger extension on the polymer within the viscoelastic solution. Following the high shear flow condition, a higher magnitude of stretch for polymer molecules in viscoelastic fluids exhibits larger elastic stresses and enhancement of vortex formation at the region.

(93)As shown in Figure 6(c), significant elastic normal stress occurs at the inlet of the constriction microchannel. Such occurrence of a polymeric flow can be attributed to the dominating elongational flow, giving rise to high deformation of the polymers within the viscoelastic fluid flow, resulting in higher elastic stress from the polymers. Such phenomena at the entrance result in the difference in velocity streamline as circled in Figure 6(d) compared to that of the Newtonian fluid at the constriction entrance in Figure 6(e).

(90) The difference between the Newtonian and polymer solution at the exit, as circled in Figure 6(d) and (e), can be attributed to the extrudate swell effect of polymers

(94) within the viscoelastic fluid flow. The extrudate swell effect illustrates that, as polymers emerge from the constriction exit, they tend to contract in the flow direction and grow in the normal direction, resulting in an extrudate diameter greater than the channel size. The deformation of polymers within the polymeric flow at both the entrance and exit of the contraction channel facilitates the change in shear stress conditions of the flow, leading to the alteration in streamlines of flows for each region.

4.3. EOF Applications in LOC Systems

4.3.1. Mixing in LOC Systems

Rather than relying on the micromixing controlled by molecular diffusion under low Reynolds number conditions, active mixers actively leverage convective instability and vortex formation induced by electro-osmotic flows from alternating current (AC) or direct current (DC) electric fields. Such adaptation is recognized as significant breakthroughs for promotion of fluid mixing in chemical and biological applications such as drug delivery, medical diagnostics, chemical synthesis, and so on.

(95)Many researchers proposed novel designs of electro-osmosis micromixers coupled with numerical simulations in conjunction with experimental findings to increase their understanding of the role of flow instability and vortex formation in the mixing process under electrokinetic phenomena. Matsubara and Narumi

(96) numerically modeled the mixing process in a microchannel with four electrodes on each side of the microchannel wall, which generated a disruption through unstable electro-osmotic vortices. It was found that particle mixing was sensitive to both the convection effect induced by the main and secondary vortex within the micromixer and the change in oscillation frequency caused by the supplied AC voltage when the Reynolds number was varied. Qaderi et al.

(97) adapted the PNP equation to numerically study the effect of the geometry and zeta potential configuration of the microchannel on the mixing process with a combined electro-osmotic pressure driven flow. It was reported that the application of heterogeneous zeta potential configuration enhances the mixing efficiency by around 23% while the height of the hurdles increases the mixing efficiency at most 48.1%. Cho et al.

(98) utilized the PB model and Laplace equation to numerically simulate the electro-osmotic non-Newtonian fluid mixing process within a wavy and block layout of microchannel walls. The Power Law model is adapted to describe the fluid rheological characteristic. It was found that shear-thinning fluids possess a higher volumetric flow rate, which could result in poorer mixing efficiency compared to that of Newtonian fluids. Numerous studies have revealed that flow instability and vortex generation, in particular secondary vortices produced by barriers or greater magnitudes of heterogeneous zeta potential distribution, enhance mixing by increasing bulk flow velocity and reducing flow distance.To better understand the mechanism of disturbance formed in the system due to externally applied forces, known as electrokinetic instability, literature often utilize the Rayleigh (Ra) number,

(1) as described below:

𝑅𝑎𝑣=𝑢ev𝑢eo=(𝛾−1𝛾+1)2𝑊𝛿2𝐸el2𝐻2𝜁𝛿Ra�=�ev�eo=(�−1�+1)2��2�el2�2��

(22)where γ is the conductivity ratio of the two streams and can be written as

𝛾=𝜎el,H𝜎el,L�=�el,H�el,L. The Ra number characterizes the ratio between electroviscous and electro-osmotic flow. A high Ra

_v value often results in good mixing. It is evident that fluid properties such as the conductivity (σ) of the two streams play a key role in the formation of disturbances to enhance mixing in microsystems. At the same time, electrokinetic parameters like the zeta potential (ζ) in the Ra number is critical in the characterization of electro-osmotic velocity and a slip boundary condition at the microchannel wall.To understand the mixing result along the channel, the concentration field can be defined and simulated under the assumption of steady state conditions and constant diffusion coefficient for each of the working fluid within the system through the convection–diffusion equation as below:

∂𝑐𝒊∂𝑡+∇⇀(𝑐𝑖𝑢⇀−𝐷𝑖∇⇀𝑐𝒊)=0∂��∂�+∇⇀(��⇀−��∇⇀��)=0

(23)where c

_i is the species concentration of species i and D

_i is the diffusion coefficient of the corresponding species.The standard deviation of concentration (σ

_sd) can be adapted to evaluate the mixing quality of the system.

(97) The standard deviation for concentration at a specific portion of the channel may be calculated using the equation below:

𝜎sd=∫10(𝐶∗(𝑦∗)−𝐶m)2d𝑦∗∫10d𝑦∗⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯�sd=∫01(�*(�*)−�m)2d�*∫01d�*

(24)where C*(y*) and C

_m are the non-dimensional concentration profile and the mean concentration at the portion, respectively. C* is the non-dimensional concentration and can be calculated as

𝐶∗=𝐶𝐶ref�*=��ref, where C

_ref is the reference concentration defined as the bulk solution concentration. The mean concentration profile can be calculated as

𝐶m=∫10(𝐶∗(𝑦∗)d𝑦∗∫10d𝑦∗�m=∫01(�*(�*)d�*∫01d�*. With the standard deviation of concentration, the mixing efficiency

(97) can then be calculated as below:

𝜀𝑥=1−𝜎sd𝜎sd,0��=1−�sd�sd,0

(25)where σ

_sd_,0 is the standard derivation of the case of no mixing. The value of the mixing efficiency is typically utilized in conjunction with the simulated flow field and concentration field to explore the effect of geometrical and electrokinetic parameters on the optimization of the mixing results.

5. Summary

ARTICLE SECTIONS

Jump To

5.1. Conclusion

Viscoelastic fluids such as blood flow in LOC systems are an essential topic to proceed with diagnostic analysis and research through microdevices in the biomedical and pharmaceutical industries. The complex blood flow behavior is tightly controlled by the viscoelastic characteristics of blood such as the dynamic viscosity and the elastic property of RBCs under various shear rate conditions. Furthermore, the flow behaviors under varied driving forces promote an array of microfluidic transport phenomena that are critical to the management of blood flow and other adapted viscoelastic fluids in LOC systems. This review addressed the blood flow phenomena, the complicated interplay between shear rate and blood flow behaviors, and their numerical modeling under LOC systems through the lens of the viscoelasticity characteristic. Furthermore, a theoretical understanding of capillary forces and externally applied electric forces leads to an in-depth investigation of the relationship between blood flow patterns and the key parameters of the two driving forces, the latter of which is introduced through the lens of viscoelastic fluids, coupling numerical modeling to improve the knowledge of blood flow manipulation in LOC systems. The flow disturbances triggered by the EOF of viscoelastic fluids and their impact on blood flow patterns have been deeply investigated due to their important role and applications in LOC devices. Continuous advancements of various numerical modeling methods with experimental findings through more efficient and less computationally heavy methods have served as an encouraging sign of establishing more accurate illustrations of the mechanisms for multiphase blood and other viscoelastic fluid flow transport phenomena driven by various forces. Such progress is fundamental for the manipulation of unique transport phenomena, such as the generated disturbances, to optimize functionalities offered by microdevices in LOC systems.

The following section will provide further insights into the employment of studied blood transport phenomena to improve the functionality of micro devices adapting LOC technology. A discussion of the novel roles that external driving forces play in microfluidic flow behaviors is also provided. Limitations in the computational modeling of blood flow and electrokinetic phenomena in LOC systems will also be emphasized, which may provide valuable insights for future research endeavors. These discussions aim to provide guidance and opportunities for new paths in the ongoing development of LOC devices that adapt blood flow.

5.2. Future Directions

5.2.1. Electro-osmosis Mixing in LOC Systems

Despite substantial research, mixing results through flow instability and vortex formation phenomena induced by electro-osmotic mixing still deviate from the effective mixing results offered by chaotic mixing results such as those seen in turbulent flows. However, recent discoveries of a mixing phenomenon that is generally observed under turbulent flows are found within electro-osmosis micromixers under low Reynolds number conditions. Zhao

(99) experimentally discovered a rapid mixing process in an AC applied micromixer, where the power spectrum of concentration under an applied voltage of 20 V

_p-p induces a −5/3 slope within a frequency range. This value of the slope is considered as the O–C spectrum in macroflows, which is often visible under relatively high Re conditions, such as the Taylor microscale Reynolds number Re > 500 in turbulent flows.

(100) However, the Re value in the studied system is less than 1 at the specific location and applied voltage. A secondary flow is also suggested to occur close to microchannel walls, being attributed to the increase of convective instability within the system.Despite the experimental phenomenon proposed by Zhao et al.,

(99) the range of effects induced by vital parameters of an EOF mixing system on the enhanced mixing results and mechanisms of disturbance generated by the turbulent-like flow instability is not further characterized. Such a gap in knowledge may hinder the adaptability and commercialization of the discovery of micromixers. One of the parameters for further evaluation is the conductivity gradient of the fluid flow. A relatively strong conductivity gradient (5000:1) was adopted in the system due to the conductive properties of the two fluids. The high conductivity gradients may contribute to the relatively large Rayleigh number and differences in EDL layer thickness, resulting in an unusual disturbance in laminar flow conditions and enhanced mixing results. However, high conductivity gradients are not always achievable by the working fluids due to diverse fluid properties. The reliance on turbulent-like phenomena and rapid mixing results in a large conductivity gradient should be established to prevent the limited application of fluids for the mixing system. In addition, the proposed system utilizes distinct zeta potential distributions at the top and bottom walls due to their difference in material choices, which may be attributed to the flow instability phenomena. Further studies should be made on varying zeta potential magnitude and distribution to evaluate their effect on the slip boundary conditions of the flow and the large shear rate condition close to the channel wall of EOF. Such a study can potentially offer an optimized condition in zeta potential magnitude through material choices and geometrical layout of the zeta potential for better mixing results and manipulation of mixing fluid dynamics. The two vital parameters mentioned above can be varied with the aid of numerical simulation to understand the effect of parameters on the interaction between electro-osmotic forces and electroviscous forces. At the same time, the relationship of developed streamlines of the simulated velocity and concentration field, following their relationship with the mixing results, under the impact of these key parameters can foster more insight into the range of impact that the two parameters have on the proposed phenomena and the microfluidic dynamic principles of disturbances.

In addition, many of the current investigations of electrokinetic mixers commonly emphasize the fluid dynamics of mixing for Newtonian fluids, while the utilization of biofluids, primarily viscoelastic fluids such as blood, and their distinctive response under shear forces in these novel mixing processes of LOC systems are significantly less studied. To develop more compatible microdevice designs and efficient mixing outcomes for the biomedical industry, it is necessary to fill the knowledge gaps in the literature on electro-osmotic mixing for biofluids, where properties of elasticity, dynamic viscosity, and intricate relationship with shear flow from the fluid are further considered.

5.2.2. Electro-osmosis Separation in LOC Systems

Particle separation in LOC devices, particularly in biological research and diagnostics, is another area where disturbances may play a significant role in optimization.

(101) Plasma analysis in LOC systems under precise control of blood flow phenomena and blood/plasma separation procedures can detect vital information about infectious diseases from particular antibodies and foreign nucleic acids for medical treatments, diagnostics, and research,

(102) offering more efficient results and simple operating procedures compared to that of the traditional centrifugation method for blood and plasma separation. However, the adaptability of LOC devices for blood and plasma separation is often hindered by microchannel clogging, where flow velocity and plasma yield from LOC devices is reduced due to occasional RBC migration and aggregation at the filtration entrance of microdevices.

(103)It is important to note that the EOF induces flow instability close to microchannel walls, which may provide further solutions to clogging for the separation process of the LOC systems. Mohammadi et al.

(104) offered an anti-clogging effect of RBCs at the blood and plasma separating device filtration entry, adjacent to the surface wall, through RBC disaggregation under high shear rate conditions generated by a forward and reverse EOF direction.

Further theoretical and numerical research can be conducted to characterize the effect of high shear rate conditions near microchannel walls toward the detachment of binding blood cells on surfaces and the reversibility of aggregation. Through numerical modeling with varying electrokinetic parameters to induce different degrees of disturbances or shear conditions at channel walls, it may be possible to optimize and better understand the process of disrupting the forces that bind cells to surface walls and aggregated cells at filtration pores. RBCs that migrate close to microchannel walls are often attracted by the adhesion force between the RBC and the solid surface originating from the van der Waals forces. Following RBC migration and attachment by adhesive forces adjacent to the microchannel walls as shown in Figure 7, the increase in viscosity at the region causes a lower shear condition and encourages RBC aggregation (cell–cell interaction), which clogs filtering pores or microchannels and reduces flow velocity at filtration region. Both the impact that shear forces and disturbances may induce on cell binding forces with surface walls and other cells leading to aggregation may suggest further characterization. Kinetic parameters such as activation energy and the rate-determining step for cell binding composition attachment and detachment should be considered for modeling the dynamics of RBCs and blood flows under external forces in LOC separation devices.

Figure 7. Schematic representations of clogging at a microchannel pore following the sequence of RBC migration, cell attachment to channel walls, and aggregation. (105) Reproduced with permission from ref (105). Copyright 2018 The Authors under the terms of the Creative Commons (CC BY 4.0) License https://creativecommons.org/licenses/by/4.0/.

5.2.3. Relationship between External Forces and Microfluidic Systems

In blood flow, a thicker CFL suggests a lower blood viscosity, suggesting a complex relationship between shear stress and shear rate, affecting the blood viscosity and blood flow. Despite some experimental and numerical studies on electro-osmotic non-Newtonian fluid flow, limited literature has performed an in-depth investigation of the role that applied electric forces and other external forces could play in the process of CFL formation. Additional studies on how shear rates from external forces affect CFL formation and microfluidic flow dynamics can shed light on the mechanism of the contribution induced by external driving forces to the development of a separate phase of layer, similar to CFL, close to the microchannel walls and distinct from the surrounding fluid within the system, then influencing microfluidic flow dynamics.One of the mechanisms of phenomena to be explored is the formation of the Exclusion Zone (EZ) region following a “Self-Induced Flow” (SIF) phenomenon discovered by Li and Pollack,

(106) as shown in Figure 8(a) and (b), respectively. A spontaneous sustained axial flow is observed when hydrophilic materials are immersed in water, resulting in the buildup of a negative layer of charges, defined as the EZ, after water molecules absorb infrared radiation (IR) energy and break down into H and OH

⁺^–.

Figure 8. Schematic representations of (a) the Exclusion Zone region and (b) the Self Induced Flow through visualization of microsphere movement within a microchannel. (106) Reproduced with permission from ref (106). Copyright 2020 The Authors under the terms of the Creative Commons (CC BY 4.0) License https://creativecommons.org/licenses/by/4.0/.

Despite the finding of such a phenomenon, the specific mechanism and role of IR energy have yet to be defined for the process of EZ development. To further develop an understanding of the role of IR energy in such phenomena, a feasible study may be seen through the lens of the relationships between external forces and microfluidic flow. In the phenomena, the increase of SIF velocity under a rise of IR radiation resonant characteristics is shown in the participation of the external electric field near the microchannel walls under electro-osmotic viscoelastic fluid flow systems. The buildup of negative charges at the hydrophilic surfaces in EZ is analogous to the mechanism of electrical double layer formation. Indeed, research has initiated the exploration of the core mechanisms for EZ formation through the lens of the electrokinetic phenomena.

(107) Such a similarity of the role of IR energy and the transport phenomena of SIF with electrokinetic phenomena paves the way for the definition of the unknown SIF phenomena and EZ formation. Furthermore, Li and Pollack

(106) suggest whether CFL formation might contribute to a SIF of blood using solely IR radiation, a commonly available source of energy in nature, as an external driving force. The proposition may be proven feasible with the presence of the CFL region next to the negatively charged hydrophilic endothelial glycocalyx layer, coating the luminal side of blood vessels.

(108) Further research can dive into the resonating characteristics between the formation of the CFL region next to the hydrophilic endothelial glycocalyx layer and that of the EZ formation close to hydrophilic microchannel walls. Indeed, an increase in IR energy is known to rapidly accelerate EZ formation and SIF velocity, depicting similarity to the increase in the magnitude of electric field forces and greater shear rates at microchannel walls affecting CFL formation and EOF velocity. Such correlation depicts a future direction in whether SIF blood flow can be observed and characterized theoretically further through the lens of the relationship between blood flow and shear forces exhibited by external energy.

The intricate link between the CFL and external forces, more specifically the externally applied electric field, can receive further attention to provide a more complete framework for the mechanisms between IR radiation and EZ formation. Such characterization may also contribute to a greater comprehension of the role IR can play in CFL formation next to the endothelial glycocalyx layer as well as its role as a driving force to propel blood flow, similar to the SIF, but without the commonly assumed pressure force from heart contraction as a source of driving force.

5.3. Challenges

Although there have been significant improvements in blood flow modeling under LOC systems over the past decade, there are still notable constraints that may require special attention for numerical simulation applications to benefit the adaptability of the designs and functionalities of LOC devices. Several points that require special attention are mentioned below:

1.	The majority of CFD models operate under the relationship between the viscoelasticity of blood and the shear rate conditions of flow. The relative effect exhibited by the presence of highly populated RBCs in whole blood and their forces amongst the cells themselves under complex flows often remains unclearly defined. Furthermore, the full range of cell populations in whole blood requires a much more computational load for numerical modeling. Therefore, a vital goal for future research is to evaluate a reduced modeling method where the impact of cell–cell interaction on the viscoelastic property of blood is considered.
2.	Current computational methods on hemodynamics rely on continuum models based upon non-Newtonian rheology at the macroscale rather than at molecular and cellular levels. Careful considerations should be made for the development of a constructive framework for the physical and temporal scales of micro/nanoscale systems to evaluate the intricate relationship between fluid driving forces, dynamic viscosity, and elasticity.
3.	Viscoelastic fluids under the impact of externally applied electric forces often deviate from the assumptions of no-slip boundary conditions due to the unique flow conditions induced by externally applied forces. Furthermore, the mechanism of vortex formation and viscoelastic flow instability at laminar flow conditions should be better defined through the lens of the microfluidic flow phenomenon to optimize the prediction of viscoelastic flow across different geometrical layouts. Mathematical models and numerical methods are needed to better predict such disturbance caused by external forces and the viscoelasticity of fluids at such a small scale.
4.	Under practical situations, zeta potential distribution at channel walls frequently deviates from the common assumption of a constant distribution because of manufacturing faults or inherent surface charges prior to the introduction of electrokinetic influence. These discrepancies frequently lead to inconsistent surface potential distribution, such as excess positive ions at relatively more negatively charged walls. Accordingly, unpredicted vortex formation and flow instability may occur. Therefore, careful consideration should be given to these discrepancies and how they could trigger the transport process and unexpected results of a microdevice.

Author Information

ARTICLE SECTIONS

Jump To

Corresponding Authors
- Zhe Chen – Department of Chemical Engineering, School of Chemistry and Chemical Engineering, State Key Laboratory of Metal Matrix Composites, Shanghai Jiao Tong University, Shanghai 200240, P. R. China; Email: zaccooky@sjtu.edu.cn
- Bo Ouyang – Department of Chemical Engineering, School of Chemistry and Chemical Engineering, State Key Laboratory of Metal Matrix Composites, Shanghai Jiao Tong University, Shanghai 200240, P. R. China; Email: bouy93@sjtu.edu.cn
- Zheng-Hong Luo – Department of Chemical Engineering, School of Chemistry and Chemical Engineering, State Key Laboratory of Metal Matrix Composites, Shanghai Jiao Tong University, Shanghai 200240, P. R. China; https://orcid.org/0000-0001-9011-6020; Email: luozh@sjtu.edu.cn
Authors
- Bin-Jie Lai – Department of Chemical Engineering, School of Chemistry and Chemical Engineering, State Key Laboratory of Metal Matrix Composites, Shanghai Jiao Tong University, Shanghai 200240, P. R. China; https://orcid.org/0009-0002-8133-5381
- Li-Tao Zhu – Department of Chemical Engineering, School of Chemistry and Chemical Engineering, State Key Laboratory of Metal Matrix Composites, Shanghai Jiao Tong University, Shanghai 200240, P. R. China; https://orcid.org/0000-0001-6514-8864
NotesThe authors declare no competing financial interest.

Acknowledgments

ARTICLE SECTIONS

Jump To

This work was supported by the National Natural Science Foundation of China (No. 22238005) and the Postdoctoral Research Foundation of China (No. GZC20231576).

Vocabulary

ARTICLE SECTIONS

Jump To

Microfluidics	the field of technological and scientific study that investigates fluid flow in channels with dimensions between 1 and 1000 μm
Lab-on-a-Chip Technology	the field of research and technological development aimed at integrating the micro/nanofluidic characteristics to conduct laboratory processes on handheld devices
Computational Fluid Dynamics (CFD)	the method utilizing computational abilities to predict physical fluid flow behaviors mathematically through solving the governing equations of corresponding fluid flows
Shear Rate	the rate of change in velocity where one layer of fluid moves past the adjacent layer
Viscoelasticity	the property holding both elasticity and viscosity characteristics relying on the magnitude of applied shear stress and time-dependent strain
Electro-osmosis	the flow of fluid under an applied electric field when charged solid surface is in contact with the bulk fluid
Vortex	the rotating motion of a fluid revolving an axis line

References

ARTICLE SECTIONS

Jump To

This article references 108 other publications.

1Neethirajan, S.; Kobayashi, I.; Nakajima, M.; Wu, D.; Nandagopal, S.; Lin, F. Microfluidics for food, agriculture and biosystems industries. Lab Chip 2011, 11 (9), 1574– 1586, DOI: 10.1039/c0lc00230eView Google Scholar
2Whitesides, G. M. The origins and the future of microfluidics. Nature 2006, 442 (7101), 368– 373, DOI: 10.1038/nature05058View Google Scholar
3Burklund, A.; Tadimety, A.; Nie, Y.; Hao, N.; Zhang, J. X. J. Chapter One – Advances in diagnostic microfluidics; Elsevier, 2020; DOI: DOI: 10.1016/bs.acc.2019.08.001 .View Google Scholar
4Abdulbari, H. A. Chapter 12 – Lab-on-a-chip for analysis of blood. In Nanotechnology for Hematology, Blood Transfusion, and Artificial Blood; Denizli, A., Nguyen, T. A., Rajan, M., Alam, M. F., Rahman, K., Eds.; Elsevier, 2022; pp 265– 283.View Google Scholar
5Vladisavljević, G. T.; Khalid, N.; Neves, M. A.; Kuroiwa, T.; Nakajima, M.; Uemura, K.; Ichikawa, S.; Kobayashi, I. Industrial lab-on-a-chip: Design, applications and scale-up for drug discovery and delivery. Advanced Drug Delivery Reviews 2013, 65 (11), 1626– 1663, DOI: 10.1016/j.addr.2013.07.017View Google Scholar
6Kersaudy-Kerhoas, M.; Dhariwal, R.; Desmulliez, M. P. Y.; Jouvet, L. Hydrodynamic blood plasma separation in microfluidic channels. Microfluid. Nanofluid. 2010, 8 (1), 105– 114, DOI: 10.1007/s10404-009-0450-5View Google Scholar
7Popel, A. S.; Johnson, P. C. Microcirculation and Hemorheology. Annu. Rev. Fluid Mech. 2005, 37 (1), 43– 69, DOI: 10.1146/annurev.fluid.37.042604.133933View Google Scholar
8Fedosov, D. A.; Peltomäki, M.; Gompper, G. Deformation and dynamics of red blood cells in flow through cylindrical microchannels. Soft Matter 2014, 10 (24), 4258– 4267, DOI: 10.1039/C4SM00248BView Google Scholar
9Chakraborty, S. Dynamics of capillary flow of blood into a microfluidic channel. Lab Chip 2005, 5 (4), 421– 430, DOI: 10.1039/b414566fView Google Scholar
10Tomaiuolo, G.; Guido, S. Start-up shape dynamics of red blood cells in microcapillary flow. Microvascular Research 2011, 82 (1), 35– 41, DOI: 10.1016/j.mvr.2011.03.004View Google Scholar
11Sherwood, J. M.; Dusting, J.; Kaliviotis, E.; Balabani, S. The effect of red blood cell aggregation on velocity and cell-depleted layer characteristics of blood in a bifurcating microchannel. Biomicrofluidics 2012, 6 (2), 24119, DOI: 10.1063/1.4717755View Google Scholar
12Nader, E.; Skinner, S.; Romana, M.; Fort, R.; Lemonne, N.; Guillot, N.; Gauthier, A.; Antoine-Jonville, S.; Renoux, C.; Hardy-Dessources, M.-D. Blood Rheology: Key Parameters, Impact on Blood Flow, Role in Sickle Cell Disease and Effects of Exercise. Frontiers in Physiology 2019, 10, 01329, DOI: 10.3389/fphys.2019.01329View Google Scholar
13Trejo-Soto, C.; Lázaro, G. R.; Pagonabarraga, I.; Hernández-Machado, A. Microfluidics Approach to the Mechanical Properties of Red Blood Cell Membrane and Their Effect on Blood Rheology. Membranes 2022, 12 (2), 217, DOI: 10.3390/membranes12020217View Google Scholar
14Wagner, C.; Steffen, P.; Svetina, S. Aggregation of red blood cells: From rouleaux to clot formation. Comptes Rendus Physique 2013, 14 (6), 459– 469, DOI: 10.1016/j.crhy.2013.04.004View Google Scholar
15Kim, H.; Zhbanov, A.; Yang, S. Microfluidic Systems for Blood and Blood Cell Characterization. Biosensors 2023, 13 (1), 13, DOI: 10.3390/bios13010013View Google Scholar
16Fåhræus, R.; Lindqvist, T. THE VISCOSITY OF THE BLOOD IN NARROW CAPILLARY TUBES. American Journal of Physiology-Legacy Content 1931, 96 (3), 562– 568, DOI: 10.1152/ajplegacy.1931.96.3.562View Google Scholar
17Ascolese, M.; Farina, A.; Fasano, A. The Fåhræus-Lindqvist effect in small blood vessels: how does it help the heart?. J. Biol. Phys. 2019, 45 (4), 379– 394, DOI: 10.1007/s10867-019-09534-4View Google Scholar
18Bento, D.; Fernandes, C. S.; Miranda, J. M.; Lima, R. In vitro blood flow visualizations and cell-free layer (CFL) measurements in a microchannel network. Experimental Thermal and Fluid Science 2019, 109, 109847, DOI: 10.1016/j.expthermflusci.2019.109847View Google Scholar
19Namgung, B.; Ong, P. K.; Wong, Y. H.; Lim, D.; Chun, K. J.; Kim, S. A comparative study of histogram-based thresholding methods for the determination of cell-free layer width in small blood vessels. Physiological Measurement 2010, 31 (9), N61, DOI: 10.1088/0967-3334/31/9/N01View Google Scholar
20Hymel, S. J.; Lan, H.; Fujioka, H.; Khismatullin, D. B. Cell trapping in Y-junction microchannels: A numerical study of the bifurcation angle effect in inertial microfluidics. Phys. Fluids (1994) 2019, 31 (8), 082003, DOI: 10.1063/1.5113516View Google Scholar
21Li, X.; Popel, A. S.; Karniadakis, G. E. Blood-plasma separation in Y-shaped bifurcating microfluidic channels: a dissipative particle dynamics simulation study. Phys. Biol. 2012, 9 (2), 026010, DOI: 10.1088/1478-3975/9/2/026010View Google Scholar
22Yin, X.; Thomas, T.; Zhang, J. Multiple red blood cell flows through microvascular bifurcations: Cell free layer, cell trajectory, and hematocrit separation. Microvascular Research 2013, 89, 47– 56, DOI: 10.1016/j.mvr.2013.05.002View Google Scholar
23Shibeshi, S. S.; Collins, W. E. The Rheology of Blood Flow in a Branched Arterial System. Appl. Rheol 2005, 15 (6), 398– 405, DOI: 10.1515/arh-2005-0020View Google Scholar
24Sequeira, A.; Janela, J. An Overview of Some Mathematical Models of Blood Rheology. In A Portrait of State-of-the-Art Research at the Technical University of Lisbon; Pereira, M. S., Ed.; Springer Netherlands: Dordrecht, 2007; pp 65– 87.View Google Scholar
25Walburn, F. J.; Schneck, D. J. A constitutive equation for whole human blood. Biorheology 1976, 13, 201– 210, DOI: 10.3233/BIR-1976-13307View Google Scholar
26Quemada, D. A rheological model for studying the hematocrit dependence of red cell-red cell and red cell-protein interactions in blood. Biorheology 1981, 18, 501– 516, DOI: 10.3233/BIR-1981-183-615View Google Scholar
27Varchanis, S.; Dimakopoulos, Y.; Wagner, C.; Tsamopoulos, J. How viscoelastic is human blood plasma?. Soft Matter 2018, 14 (21), 4238– 4251, DOI: 10.1039/C8SM00061AView Google Scholar
28Apostolidis, A. J.; Moyer, A. P.; Beris, A. N. Non-Newtonian effects in simulations of coronary arterial blood flow. J. Non-Newtonian Fluid Mech. 2016, 233, 155– 165, DOI: 10.1016/j.jnnfm.2016.03.008View Google Scholar
29Luo, X. Y.; Kuang, Z. B. A study on the constitutive equation of blood. J. Biomech. 1992, 25 (8), 929– 934, DOI: 10.1016/0021-9290(92)90233-QView Google Scholar
30Oldroyd, J. G.; Wilson, A. H. On the formulation of rheological equations of state. Proceedings of the Royal Society of London. Series A. Mathematical and Physical Sciences 1950, 200 (1063), 523– 541, DOI: 10.1098/rspa.1950.0035View Google Scholar
31Prado, G.; Farutin, A.; Misbah, C.; Bureau, L. Viscoelastic transient of confined red blood cells. Biophys J. 2015, 108 (9), 2126– 2136, DOI: 10.1016/j.bpj.2015.03.046View Google Scholar
32Huang, C. R.; Pan, W. D.; Chen, H. Q.; Copley, A. L. Thixotropic properties of whole blood from healthy human subjects. Biorheology 1987, 24 (6), 795– 801, DOI: 10.3233/BIR-1987-24630View Google Scholar
33Anand, M.; Kwack, J.; Masud, A. A new generalized Oldroyd-B model for blood flow in complex geometries. International Journal of Engineering Science 2013, 72, 78– 88, DOI: 10.1016/j.ijengsci.2013.06.009View Google Scholar
34Horner, J. S.; Armstrong, M. J.; Wagner, N. J.; Beris, A. N. Investigation of blood rheology under steady and unidirectional large amplitude oscillatory shear. J. Rheol. 2018, 62 (2), 577– 591, DOI: 10.1122/1.5017623View Google Scholar
35Horner, J. S.; Armstrong, M. J.; Wagner, N. J.; Beris, A. N. Measurements of human blood viscoelasticity and thixotropy under steady and transient shear and constitutive modeling thereof. J. Rheol. 2019, 63 (5), 799– 813, DOI: 10.1122/1.5108737View Google Scholar
36Armstrong, M.; Tussing, J. A methodology for adding thixotropy to Oldroyd-8 family of viscoelastic models for characterization of human blood. Phys. Fluids 2020, 32 (9), 094111, DOI: 10.1063/5.0022501View Google Scholar
37Crank, J.; Nicolson, P. A practical method for numerical evaluation of solutions of partial differential equations of the heat-conduction type. Mathematical Proceedings of the Cambridge Philosophical Society 1947, 43 (1), 50– 67, DOI: 10.1017/S0305004100023197View Google Scholar
38Clough, R. W. Original formulation of the finite element method. Finite Elements in Analysis and Design 1990, 7 (2), 89– 101, DOI: 10.1016/0168-874X(90)90001-UView Google Scholar
39Liu, W. K.; Liu, Y.; Farrell, D.; Zhang, L.; Wang, X. S.; Fukui, Y.; Patankar, N.; Zhang, Y.; Bajaj, C.; Lee, J.Immersed finite element method and its applications to biological systems. Computer Methods in Applied Mechanics and Engineering 2006, 195 (13), 1722– 1749, DOI: 10.1016/j.cma.2005.05.049View Google Scholar
40Lopes, D.; Agujetas, R.; Puga, H.; Teixeira, J.; Lima, R.; Alejo, J. P.; Ferrera, C. Analysis of finite element and finite volume methods for fluid-structure interaction simulation of blood flow in a real stenosed artery. International Journal of Mechanical Sciences 2021, 207, 106650, DOI: 10.1016/j.ijmecsci.2021.106650View Google Scholar
41Favero, J. L.; Secchi, A. R.; Cardozo, N. S. M.; Jasak, H. Viscoelastic flow analysis using the software OpenFOAM and differential constitutive equations. J. Non-Newtonian Fluid Mech. 2010, 165 (23), 1625– 1636, DOI: 10.1016/j.jnnfm.2010.08.010View Google Scholar
42Pimenta, F.; Alves, M. A. Stabilization of an open-source finite-volume solver for viscoelastic fluid flows. J. Non-Newtonian Fluid Mech. 2017, 239, 85– 104, DOI: 10.1016/j.jnnfm.2016.12.002View Google Scholar
43Chee, C. Y.; Lee, H. P.; Lu, C. Using 3D fluid-structure interaction model to analyse the biomechanical properties of erythrocyte. Phys. Lett. A 2008, 372 (9), 1357– 1362, DOI: 10.1016/j.physleta.2007.09.067View Google Scholar
44Xu, D.; Kaliviotis, E.; Munjiza, A.; Avital, E.; Ji, C.; Williams, J. Large scale simulation of red blood cell aggregation in shear flows. J. Biomech. 2013, 46 (11), 1810– 1817, DOI: 10.1016/j.jbiomech.2013.05.010View Google Scholar
45Johnson, K. L.; Kendall, K.; Roberts, A. Surface energy and the contact of elastic solids. Proceedings of the royal society of London. A. mathematical and physical sciences 1971, 324 (1558), 301– 313, DOI: 10.1098/rspa.1971.0141View Google Scholar
46Shi, L.; Pan, T.-W.; Glowinski, R. Deformation of a single red blood cell in bounded Poiseuille flows. Phys. Rev. E 2012, 85 (1), 016307, DOI: 10.1103/PhysRevE.85.016307View Google Scholar
47Yoon, D.; You, D. Continuum modeling of deformation and aggregation of red blood cells. J. Biomech. 2016, 49 (11), 2267– 2279, DOI: 10.1016/j.jbiomech.2015.11.027View Google Scholar
48Mainardi, F.; Spada, G. Creep, relaxation and viscosity properties for basic fractional models in rheology. European Physical Journal Special Topics 2011, 193 (1), 133– 160, DOI: 10.1140/epjst/e2011-01387-1View Google Scholar
49Gracka, M.; Lima, R.; Miranda, J. M.; Student, S.; Melka, B.; Ostrowski, Z. Red blood cells tracking and cell-free layer formation in a microchannel with hyperbolic contraction: A CFD model validation. Computer Methods and Programs in Biomedicine 2022, 226, 107117, DOI: 10.1016/j.cmpb.2022.107117View Google Scholar
50Aryan, H.; Beigzadeh, B.; Siavashi, M. Euler-Lagrange numerical simulation of improved magnetic drug delivery in a three-dimensional CT-based carotid artery bifurcation. Computer Methods and Programs in Biomedicine 2022, 219, 106778, DOI: 10.1016/j.cmpb.2022.106778View Google Scholar
51Czaja, B.; Závodszky, G.; Azizi Tarksalooyeh, V.; Hoekstra, A. G. Cell-resolved blood flow simulations of saccular aneurysms: effects of pulsatility and aspect ratio. J. R Soc. Interface 2018, 15 (146), 20180485, DOI: 10.1098/rsif.2018.0485View Google Scholar
52Rydquist, G.; Esmaily, M. A cell-resolved, Lagrangian solver for modeling red blood cell dynamics in macroscale flows. J. Comput. Phys. 2022, 461, 111204, DOI: 10.1016/j.jcp.2022.111204View Google Scholar
53Dadvand, A.; Baghalnezhad, M.; Mirzaee, I.; Khoo, B. C.; Ghoreishi, S. An immersed boundary-lattice Boltzmann approach to study the dynamics of elastic membranes in viscous shear flows. Journal of Computational Science 2014, 5 (5), 709– 718, DOI: 10.1016/j.jocs.2014.06.006View Google Scholar
54Krüger, T.; Holmes, D.; Coveney, P. V. Deformability-based red blood cell separation in deterministic lateral displacement devices─A simulation study. Biomicrofluidics 2014, 8 (5), 054114, DOI: 10.1063/1.4897913View Google Scholar
55Takeishi, N.; Ito, H.; Kaneko, M.; Wada, S. Deformation of a Red Blood Cell in a Narrow Rectangular Microchannel. Micromachines 2019, 10 (3), 199, DOI: 10.3390/mi10030199View Google Scholar
56Krüger, T.; Varnik, F.; Raabe, D. Efficient and accurate simulations of deformable particles immersed in a fluid using a combined immersed boundary lattice Boltzmann finite element method. Computers & Mathematics with Applications 2011, 61 (12), 3485– 3505, DOI: 10.1016/j.camwa.2010.03.057View Google Scholar
57Balachandran Nair, A. N.; Pirker, S.; Umundum, T.; Saeedipour, M. A reduced-order model for deformable particles with application in bio-microfluidics. Computational Particle Mechanics 2020, 7 (3), 593– 601, DOI: 10.1007/s40571-019-00283-8View Google Scholar
58Balachandran Nair, A. N.; Pirker, S.; Saeedipour, M. Resolved CFD-DEM simulation of blood flow with a reduced-order RBC model. Computational Particle Mechanics 2022, 9 (4), 759– 774, DOI: 10.1007/s40571-021-00441-xView Google Scholar
59Mittal, R.; Iaccarino, G. IMMERSED BOUNDARY METHODS. Annu. Rev. Fluid Mech. 2005, 37 (1), 239– 261, DOI: 10.1146/annurev.fluid.37.061903.175743View Google Scholar
60Piquet, A.; Roussel, O.; Hadjadj, A. A comparative study of Brinkman penalization and direct-forcing immersed boundary methods for compressible viscous flows. Computers & Fluids 2016, 136, 272– 284, DOI: 10.1016/j.compfluid.2016.06.001View Google Scholar
61Akerkouch, L.; Le, T. B. A Hybrid Continuum-Particle Approach for Fluid-Structure Interaction Simulation of Red Blood Cells in Fluid Flows. Fluids 2021, 6 (4), 139, DOI: 10.3390/fluids6040139View Google Scholar
62Barker, A. T.; Cai, X.-C. Scalable parallel methods for monolithic coupling in fluid-structure interaction with application to blood flow modeling. J. Comput. Phys. 2010, 229 (3), 642– 659, DOI: 10.1016/j.jcp.2009.10.001View Google Scholar
63Cetin, A.; Sahin, M. A monolithic fluid-structure interaction framework applied to red blood cells. International Journal for Numerical Methods in Biomedical Engineering 2019, 35 (2), e3171 DOI: 10.1002/cnm.3171View Google Scholar
64Freund, J. B. Numerical Simulation of Flowing Blood Cells. Annu. Rev. Fluid Mech. 2014, 46 (1), 67– 95, DOI: 10.1146/annurev-fluid-010313-141349View Google Scholar
65Ye, T.; Phan-Thien, N.; Lim, C. T. Particle-based simulations of red blood cells─A review. J. Biomech. 2016, 49 (11), 2255– 2266, DOI: 10.1016/j.jbiomech.2015.11.050View Google Scholar
66Arabghahestani, M.; Poozesh, S.; Akafuah, N. K. Advances in Computational Fluid Mechanics in Cellular Flow Manipulation: A Review. Applied Sciences 2019, 9 (19), 4041, DOI: 10.3390/app9194041View Google Scholar
67Rathnayaka, C. M.; From, C. S.; Geekiyanage, N. M.; Gu, Y. T.; Nguyen, N. T.; Sauret, E. Particle-Based Numerical Modelling of Liquid Marbles: Recent Advances and Future Perspectives. Archives of Computational Methods in Engineering 2022, 29 (5), 3021– 3039, DOI: 10.1007/s11831-021-09683-7View Google Scholar
68Li, X.; Vlahovska, P. M.; Karniadakis, G. E. Continuum- and particle-based modeling of shapes and dynamics of red blood cells in health and disease. Soft Matter 2013, 9 (1), 28– 37, DOI: 10.1039/C2SM26891DView Google Scholar
69Beris, A. N.; Horner, J. S.; Jariwala, S.; Armstrong, M. J.; Wagner, N. J. Recent advances in blood rheology: a review. Soft Matter 2021, 17 (47), 10591– 10613, DOI: 10.1039/D1SM01212FView Google Scholar
70Arciero, J.; Causin, P.; Malgaroli, F. Mathematical methods for modeling the microcirculation. AIMS Biophysics 2017, 4 (3), 362– 399, DOI: 10.3934/biophy.2017.3.362View Google Scholar
71Maria, M. S.; Chandra, T. S.; Sen, A. K. Capillary flow-driven blood plasma separation and on-chip analyte detection in microfluidic devices. Microfluid. Nanofluid. 2017, 21 (4), 72, DOI: 10.1007/s10404-017-1907-6View Google Scholar
72Huhtamäki, T.; Tian, X.; Korhonen, J. T.; Ras, R. H. A. Surface-wetting characterization using contact-angle measurements. Nat. Protoc. 2018, 13 (7), 1521– 1538, DOI: 10.1038/s41596-018-0003-zView Google Scholar
73Young, T., III. An essay on the cohesion of fluids. Philosophical Transactions of the Royal Society of London 1805, 95, 65– 87, DOI: 10.1098/rstl.1805.0005View Google Scholar
74Kim, Y. C.; Kim, S.-H.; Kim, D.; Park, S.-J.; Park, J.-K. Plasma extraction in a capillary-driven microfluidic device using surfactant-added poly(dimethylsiloxane). Sens. Actuators, B 2010, 145 (2), 861– 868, DOI: 10.1016/j.snb.2010.01.017View Google Scholar
75Washburn, E. W. The Dynamics of Capillary Flow. Physical Review 1921, 17 (3), 273– 283, DOI: 10.1103/PhysRev.17.273View Google Scholar
76Cito, S.; Ahn, Y. C.; Pallares, J.; Duarte, R. M.; Chen, Z.; Madou, M.; Katakis, I. Visualization and measurement of capillary-driven blood flow using spectral domain optical coherence tomography. Microfluid Nanofluidics 2012, 13 (2), 227– 237, DOI: 10.1007/s10404-012-0950-6View Google Scholar
77Berthier, E.; Dostie, A. M.; Lee, U. N.; Berthier, J.; Theberge, A. B. Open Microfluidic Capillary Systems. Anal Chem. 2019, 91 (14), 8739– 8750, DOI: 10.1021/acs.analchem.9b01429View Google Scholar
78Berthier, J.; Brakke, K. A.; Furlani, E. P.; Karampelas, I. H.; Poher, V.; Gosselin, D.; Cubizolles, M.; Pouteau, P. Whole blood spontaneous capillary flow in narrow V-groove microchannels. Sens. Actuators, B 2015, 206, 258– 267, DOI: 10.1016/j.snb.2014.09.040View Google Scholar
79Hirt, C. W.; Nichols, B. D. Volume of fluid (VOF) method for the dynamics of free boundaries. J. Comput. Phys. 1981, 39 (1), 201– 225, DOI: 10.1016/0021-9991(81)90145-5View Google Scholar
80Chen, J.-L.; Shih, W.-H.; Hsieh, W.-H. AC electro-osmotic micromixer using a face-to-face, asymmetric pair of planar electrodes. Sens. Actuators, B 2013, 188, 11– 21, DOI: 10.1016/j.snb.2013.07.012View Google Scholar
81Zhao, C.; Yang, C. Electrokinetics of non-Newtonian fluids: A review. Advances in Colloid and Interface Science 2013, 201-202, 94– 108, DOI: 10.1016/j.cis.2013.09.001View Google Scholar
82Oh, K. W. 6 – Lab-on-chip (LOC) devices and microfluidics for biomedical applications. In MEMS for Biomedical Applications; Bhansali, S., Vasudev, A., Eds.; Woodhead Publishing, 2012; pp 150– 171.View Google Scholar
83Bello, M. S.; De Besi, P.; Rezzonico, R.; Righetti, P. G.; Casiraghi, E. Electroosmosis of polymer solutions in fused silica capillaries. ELECTROPHORESIS 1994, 15 (1), 623– 626, DOI: 10.1002/elps.1150150186View Google Scholar
84Park, H. M.; Lee, W. M. Effect of viscoelasticity on the flow pattern and the volumetric flow rate in electroosmotic flows through a microchannel. Lab Chip 2008, 8 (7), 1163– 1170, DOI: 10.1039/b800185eView Google Scholar
85Afonso, A. M.; Alves, M. A.; Pinho, F. T. Analytical solution of mixed electro-osmotic/pressure driven flows of viscoelastic fluids in microchannels. J. Non-Newtonian Fluid Mech. 2009, 159 (1), 50– 63, DOI: 10.1016/j.jnnfm.2009.01.006View Google Scholar
86Sousa, J. J.; Afonso, A. M.; Pinho, F. T.; Alves, M. A. Effect of the skimming layer on electro-osmotic─Poiseuille flows of viscoelastic fluids. Microfluid. Nanofluid. 2011, 10 (1), 107– 122, DOI: 10.1007/s10404-010-0651-yView Google Scholar
87Zhao, C.; Yang, C. Electro-osmotic mobility of non-Newtonian fluids. Biomicrofluidics 2011, 5 (1), 014110, DOI: 10.1063/1.3571278View Google Scholar
88Pimenta, F.; Alves, M. A. Electro-elastic instabilities in cross-shaped microchannels. J. Non-Newtonian Fluid Mech. 2018, 259, 61– 77, DOI: 10.1016/j.jnnfm.2018.04.004View Google Scholar
89Bezerra, W. S.; Castelo, A.; Afonso, A. M. Numerical Study of Electro-Osmotic Fluid Flow and Vortex Formation. Micromachines (Basel) 2019, 10 (12), 796, DOI: 10.3390/mi10120796View Google Scholar
90Ji, J.; Qian, S.; Liu, Z. Electroosmotic Flow of Viscoelastic Fluid through a Constriction Microchannel. Micromachines (Basel) 2021, 12 (4), 417, DOI: 10.3390/mi12040417View Google Scholar
91Zhao, C.; Yang, C. Exact solutions for electro-osmotic flow of viscoelastic fluids in rectangular micro-channels. Applied Mathematics and Computation 2009, 211 (2), 502– 509, DOI: 10.1016/j.amc.2009.01.068View Google Scholar
92Gerum, R.; Mirzahossein, E.; Eroles, M.; Elsterer, J.; Mainka, A.; Bauer, A.; Sonntag, S.; Winterl, A.; Bartl, J.; Fischer, L. Viscoelastic properties of suspended cells measured with shear flow deformation cytometry. Elife 2022, 11, e78823, DOI: 10.7554/eLife.78823View Google Scholar
93Sadek, S. H.; Pinho, F. T.; Alves, M. A. Electro-elastic flow instabilities of viscoelastic fluids in contraction/expansion micro-geometries. J. Non-Newtonian Fluid Mech. 2020, 283, 104293, DOI: 10.1016/j.jnnfm.2020.104293View Google Scholar
94Spanjaards, M.; Peters, G.; Hulsen, M.; Anderson, P. Numerical Study of the Effect of Thixotropy on Extrudate Swell. Polymers 2021, 13 (24), 4383, DOI: 10.3390/polym13244383View Google Scholar
95Rashidi, S.; Bafekr, H.; Valipour, M. S.; Esfahani, J. A. A review on the application, simulation, and experiment of the electrokinetic mixers. Chemical Engineering and Processing – Process Intensification 2018, 126, 108– 122, DOI: 10.1016/j.cep.2018.02.021View Google Scholar
96Matsubara, K.; Narumi, T. Microfluidic mixing using unsteady electroosmotic vortices produced by a staggered array of electrodes. Chemical Engineering Journal 2016, 288, 638– 647, DOI: 10.1016/j.cej.2015.12.013View Google Scholar
97Qaderi, A.; Jamaati, J.; Bahiraei, M. CFD simulation of combined electroosmotic-pressure driven micro-mixing in a microchannel equipped with triangular hurdle and zeta-potential heterogeneity. Chemical Engineering Science 2019, 199, 463– 477, DOI: 10.1016/j.ces.2019.01.034View Google Scholar
98Cho, C.-C.; Chen, C.-L.; Chen, C. o.-K. Mixing enhancement in crisscross micromixer using aperiodic electrokinetic perturbing flows. International Journal of Heat and Mass Transfer 2012, 55 (11), 2926– 2933, DOI: 10.1016/j.ijheatmasstransfer.2012.02.006View Google Scholar
99Zhao, W.; Yang, F.; Wang, K.; Bai, J.; Wang, G. Rapid mixing by turbulent-like electrokinetic microflow. Chemical Engineering Science 2017, 165, 113– 121, DOI: 10.1016/j.ces.2017.02.027View Google Scholar
100Tran, T.; Chakraborty, P.; Guttenberg, N.; Prescott, A.; Kellay, H.; Goldburg, W.; Goldenfeld, N.; Gioia, G. Macroscopic effects of the spectral structure in turbulent flows. Nat. Phys. 2010, 6 (6), 438– 441, DOI: 10.1038/nphys1674View Google Scholar
101Toner, M.; Irimia, D. Blood-on-a-chip. Annu. Rev. Biomed Eng. 2005, 7, 77– 103, DOI: 10.1146/annurev.bioeng.7.011205.135108View Google Scholar
102Maria, M. S.; Rakesh, P. E.; Chandra, T. S.; Sen, A. K. Capillary flow of blood in a microchannel with differential wetting for blood plasma separation and on-chip glucose detection. Biomicrofluidics 2016, 10 (5), 054108, DOI: 10.1063/1.4962874View Google Scholar
103Tripathi, S.; Varun Kumar, Y. V. B.; Prabhakar, A.; Joshi, S. S.; Agrawal, A. Passive blood plasma separation at the microscale: a review of design principles and microdevices. Journal of Micromechanics and Microengineering 2015, 25 (8), 083001, DOI: 10.1088/0960-1317/25/8/083001View Google Scholar
104Mohammadi, M.; Madadi, H.; Casals-Terré, J. Microfluidic point-of-care blood panel based on a novel technique: Reversible electroosmotic flow. Biomicrofluidics 2015, 9 (5), 054106, DOI: 10.1063/1.4930865View Google Scholar
105Kang, D. H.; Kim, K.; Kim, Y. J. An anti-clogging method for improving the performance and lifespan of blood plasma separation devices in real-time and continuous microfluidic systems. Sci. Rep 2018, 8 (1), 17015, DOI: 10.1038/s41598-018-35235-4View Google Scholar
106Li, Z.; Pollack, G. H. Surface-induced flow: A natural microscopic engine using infrared energy as fuel. Science Advances 2020, 6 (19), eaba0941 DOI: 10.1126/sciadv.aba0941View Google Scholar
107Mercado-Uribe, H.; Guevara-Pantoja, F. J.; García-Muñoz, W.; García-Maldonado, J. S.; Méndez-Alcaraz, J. M.; Ruiz-Suárez, J. C. On the evolution of the exclusion zone produced by hydrophilic surfaces: A contracted description. J. Chem. Phys. 2021, 154 (19), 194902, DOI: 10.1063/5.0043084View Google Scholar
108Yalcin, O.; Jani, V. P.; Johnson, P. C.; Cabrales, P. Implications Enzymatic Degradation of the Endothelial Glycocalyx on the Microvascular Hemodynamics and the Arteriolar Red Cell Free Layer of the Rat Cremaster Muscle. Front Physiol 2018, 9, 168, DOI: 10.3389/fphys.2018.00168View Google Scholar

Schematic view of the experimental set-up

Short-time numerical simulation of ultrasonically assisted electrochemical removal of strontium from water

September 2023

DOI:10.30955/gnc2023.00436

Conference: 18th International Conference on Environmental Science and Technology CEST2023, 30 August to 2 September 2023, Athens, Greece
At: Athens, Greece

Authors:

Katarina Licht

University of Zagreb Faculty of Civil Engineering

Ivan Halkijevic

University of Zagreb

Hana Posavcic

University of Zagreb

Goran Loncar

University of Zagreb

Abstract and Figures

3D numerical simulations and measurements on an electrochemical reactor were used to analyze the efficiency of strontium removal from water, with and without simultaneous ultrasound treatment. Ultrasound was generated using 4 ultrasonic transducers with an operating frequency of 25 kHz. The reactor used 8 aluminum electrodes arranged in two blocks. Strontium ions in water are modeled as particles characterized by a charge of 3.2•10-19 C and a diameter of 1.2•10-8 m. The numerical model was created in Flow-3D software using the basic hydrodynamic module, electrostatic module, and general moving objects module. The performance of the studied reactor variants by numerical simulations is defined by the ratio of the number of model strontium particles permanently retained on the electrodes at the end of the simulation period to the initial number of particles in the water. For the laboratory reactor, the effect of strontium removal is defined by the ratio of the homogeneous strontium concentration in the water at the end and at the beginning of the experiments. The results show that the use of ultrasound increases the effect of strontium removal from 10.3% to 11.2% after 180 seconds of water treatment. The results of numerical simulations agree with the results of measurements on a reactor with the same geometrical characteristics.

Keywords:

numerical model, electrochemical reactor, strontium

1. Introduction

Strontium (Sr) is a naturally occurring element found in many sedimentary rocks and some calcite minerals. Significant anthropogenic sources include industrial activities, fertilizers, and nuclear fallout (Scott et al., 2020). Sr concentrations greater than 1.5 mg L-1 in water can cause strontium rickets and other health problems in humans, especially in children (Epa et al., n.d.; Peng et al., 2021; Scott et al., 2020). Elevated Sr concentrations have been reported in drinking water worldwide, with concentrations as high as 52 mg L-1 in groundwater in the northern USA (Luczaj and Masarik, 2015; Peng et al., 2021; Scott et al., 2020). One of the possible remediation technologies for Sr is an electrochemical process (Kamaraj and Vasudevan, 2015). These processes are based on in-situ coagulant formation through the application of electric current to metal electrodes. The process consists of dissolution of the sacrificial anode, formation of hydroxide ions and hydrogen at the cathode, electrolyte reactions at the electrode surface, adsorption of coagulants on colloidal impurities and electrodes, and removal of the resulting flocs by precipitation or flotation (Mollah et al., 2001). One of the main drawbacks of the process is the polarization and passivation of the electrodes, which can be minimized by combining it with ultrasonication (Dong et al., 2016; Ince, 2018; Moradi et al., 2021). Ultrasonic cavitation can result in solute thermolysis and the formation of reactive species such as hydroxyl radicals and hydrogen peroxide (Mohapatra and Kirpalani, 2019). It also increases the mass transfer rates of solutes and enhances the surface properties of solid particles (Fu et al., 2016; Ziylan et al., 2013). The aim of this research is to evaluate the efficiency of the electrochemical (EC) batch reactor with and without the additional use of ultrasound (US), which is intended for the purification of water mainly contaminated with an increased concentration of Sr. The results of the 3D numerical simulations are verified by measurements in the laboratory EC reactor.

References

https://doi.org/10.1016/J.JHAZMAT.2016.07.007

EPA. (2014), Announcement of Final Regulatory Determinations for Contaminants on the Third Drinking

Water Contaminant Candidate List. Retrieved from http://fdsys.gpo.gov/fdsys/search/home.action

Fu, F., Lu, J., Cheng, Z. and Tang, B. (2016), Removal of selenite by zero-valent iron combined with ultrasound:

Se(IV) concentration changes, Se(VI) generation, and reaction mechanism, Ultrasonics Sonochemistry, 29,

328–336. https://doi.org/10.1016/j.ultsonch.2015.10.007 Ince, N.H. (2018), Ultrasound-assisted advanced oxidation processes for water decontamination, Ultrasonics Sonochemistry, 40, 97–103.

https://doi.org/10.1016/j.ultsonch.2017.04.009

Kamaraj, R. and Vasudevan, S. (2015), Evaluation of electrocoagulation processfor the removal of strontium and cesium from aqueous solution, Chemical Engineering Research and Design, 93, 522–530.

https://doi.org/10.1016/j.cherd.2014.03.021

Luczaj, J. and Masarik, K. (2015), Groundwater Quantity and Quality Issues in a Water-Rich Region: Examples from Wisconsin, USA, Resources, 4(2), 323–357.

https://doi.org/10.3390/resources4020323

Mohapatra, D.P. and Kirpalani, D.M. (2019), Selenium in wastewater: fast analysis method development and advanced oxidation treatment applications, Water Science and Technology: A Journal of the International Association on Water Pollution Research, 79(5), 842–849. https://doi.org/10.2166/wst.2019.010

Mollah, M.Y.A., Schennach, R., Parga, J.R. and Cocke, D.L. (2001), Electrocoagulation (EC)- Science and

applications, Journal of Hazardous Materials, 84(1), 29–41. https://doi.org/10.1016/S0304-3894(01)00176-5 Moradi, M., Vasseghian, Y., Arabzade, H. and Khaneghah, A.M. (2021), Various wastewaters treatment by sono-electrocoagulation process: A comprehensive review of operational parameters and future outlook, Chemosphere, 263, 128314.https://doi.org/10.1016/J.CHEMOSPHERE.2020.128314

Peng, H., Yao, F., Xiong, S., Wu, Z., Niu, G. and Lu, T. (2021), Strontium in public drinking water and associated public health risks in Chinese cities, Environmental Science and Pollution Research International, 28(18), 23048.

https://doi.org/10.1007/S11356-021-12378-Y

Scott, V., Juran, L., Ling, E.J., Benham, B. and Spiller, A. (2020), Assessing strontium and vulnerability to

strontium in private drinking water systems in Virginia, Water, 12(4). https://doi.org/10.3390/w12041053

Ziylan, A., Koltypin, Y., Gedanken, A. and Ince, N.H. (2013), More on sonolytic and sonocatalytic decomposition of Diclofenac using zero-valent iron, Ultrasonics Sonochemistry, 20(1), 580–586.

https://doi.org/10.1016/j.ultsonch.2012.05.005

PDF FullText View

Predicting solid-state phase transformations during metal additive manufacturing: A case study on electron-beam powder bed fusion of Inconel-738

금속 적층 제조 중 고체 상 변형 예측: Inconel-738의 전자빔 분말층 융합에 대한 사례 연구

Nana Kwabena Adomako ^a, Nima Haghdadi ^a, James F.L. Dingle ^bc, Ernst Kozeschnik ^d, Xiaozhou Liao ^bc, Simon P. Ringer ^bc, Sophie Primig ^a

Abstract

Metal additive manufacturing (AM) has now become the perhaps most desirable technique for producing complex shaped engineering parts. However, to truly take advantage of its capabilities, advanced control of AM microstructures and properties is required, and this is often enabled via modeling. The current work presents a computational modeling approach to studying the solid-state phase transformation kinetics and the microstructural evolution during AM. Our approach combines thermal and thermo-kinetic modelling. A semi-analytical heat transfer model is employed to simulate the thermal history throughout AM builds. Thermal profiles of individual layers are then used as input for the MatCalc thermo-kinetic software. The microstructural evolution (e.g., fractions, morphology, and composition of individual phases) for any region of interest throughout the build is predicted by MatCalc. The simulation is applied to an IN738 part produced by electron beam powder bed fusion to provide insights into how γ′ precipitates evolve during thermal cycling. Our simulations show qualitative agreement with our experimental results in predicting the size distribution of γ′ along the build height, its multimodal size character, as well as the volume fraction of MC carbides. Our findings indicate that our method is suitable for a range of AM processes and alloys, to predict and engineer their microstructures and properties.

Graphical Abstract

Keywords

Additive manufacturing, Simulation, Thermal cycles, γ′ phase, IN738

1. Introduction

Additive manufacturing (AM) is an advanced manufacturing method that enables engineering parts with intricate shapes to be fabricated with high efficiency and minimal materials waste. AM involves building up 3D components layer-by-layer from feedstocks such as powder [1]. Various alloys, including steel, Ti, Al, and Ni-based superalloys, have been produced using different AM techniques. These techniques include directed energy deposition (DED), electron- and laser powder bed fusion (E-PBF and L-PBF), and have found applications in a variety of industries such as aerospace and power generation [2], [3], [4]. Despite the growing interest, certain challenges limit broader applications of AM fabricated components in these industries and others. One of such limitations is obtaining a suitable and reproducible microstructure that offers the desired mechanical properties consistently. In fact, the AM as-built microstructure is highly complex and considerably distinctive from its conventionally processed counterparts owing to the complicated thermal cycles arising from the deposition of several layers upon each other [5], [6].

Several studies have reported that the solid-state phases and solidification microstructure of AM processed alloys such as CMSX-4, CoCr [7], [8], Ti-6Al-4V [9], [10], [11], IN738 [6], 304L stainless steel [12], and IN718 [13], [14] exhibit considerable variations along the build direction. For instance, references [9], [10] have reported that there is a variation in the distribution of α and β phases along the build direction in Ti-alloys. Similarly, the microstructure of an L-PBF fabricated martensitic steel exhibits variations in the fraction of martensite [15]. Furthermore, some of the present authors and others [6], [16], [17], [18], [19], [20] have recently reviewed and reported that there is a difference in the morphology and fraction of nanoscale precipitates as a function of build height in Ni-based superalloys. These non-uniformities in the as-built microstructure result in an undesired heterogeneity in mechanical and other important properties such as corrosion and oxidation [19], [21], [22], [23]. To obtain the desired microstructure and properties, additional processing treatments are utilized, but this incurs extra costs and may lead to precipitation of detrimental phases and grain coarsening. Therefore, a through-process understanding of the microstructure evolution under repeated heating and cooling is now needed to further advance 3D printed microstructure and property control.

It is now commonly understood that the microstructure evolution during printing is complex, and most AM studies concentrate on the microstructure and mechanical properties of the final build only. Post-printing studies of microstructure characteristics at room temperature miss crucial information on how they evolve. In-situ measurements and modelling approaches are required to better understand the complex microstructural evolution under repeated heating and cooling. Most in-situ measurements in AM focus on monitoring the microstructural changes, such as phase transformations and melt pool dynamics during fabrication using X-ray scattering and high-speed X-ray imaging [24], [25], [26], [27]. For example, Zhao et al. [25] measured the rate of solidification and described the α/β phase transformation during L-PBF of Ti-6Al-4V in-situ. Also, Wahlmann et al. [21] recently used an L-PBF machine coupled with X-ray scattering to investigate the changes in CMSX-4 phase during successive melting processes. Although these techniques provide significant understanding of the basic principles of AM, they are not widely accessible. This is due to the great cost of the instrument, competitive application process, and complexities in terms of the experimental set-up, data collection, and analysis [26], [28].

Computational modeling techniques are promising and more widely accessible tools that enable advanced understanding, prediction, and engineering of microstructures and properties during AM. So far, the majority of computational studies have concentrated on physics based process models for metal AM, with the goal of predicting the temperature profile, heat transfer, powder dynamics, and defect formation (e.g., porosity) [29], [30]. In recent times, there have been efforts in modeling of the AM microstructure evolution using approaches such as phase-field [31], Monte Carlo (MC) [32], and cellular automata (CA) [33], coupled with finite element simulations for temperature profiles. However, these techniques are often restricted to simulating the evolution of solidification microstructures (e.g., grain and dendrite structure) and defects (e.g., porosity). For example, Zinovieva et al. [33] predicted the grain structure of L-PBF Ti-6Al-4V using finite difference and cellular automata methods. However, studies on the computational modelling of the solid-state phase transformations, which largely determine the resulting properties, remain limited. This can be attributed to the multi-component and multi-phase nature of most engineering alloys in AM, along with the complex transformation kinetics during thermal cycling. This kind of research involves predictions of the thermal cycle in AM builds, and connecting it to essential thermodynamic and kinetic data as inputs for the model. Based on the information provided, the thermokinetic model predicts the history of solid-state phase microstructure evolution during deposition as output. For example, a multi-phase, multi-component mean-field model has been developed to simulate the intermetallic precipitation kinetics in IN718 [34] and IN625 [35] during AM. Also, Basoalto et al. [36] employed a computational framework to examine the contrasting distributions of process-induced microvoids and precipitates in two Ni-based superalloys, namely IN718 and CM247LC. Furthermore, McNamara et al. [37] established a computational model based on the Johnson-Mehl-Avrami model for non-isothermal conditions to predict solid-state phase transformation kinetics in L-PBF IN718 and DED Ti-6Al-4V. These models successfully predicted the size and volume fraction of individual phases and captured the repeated nucleation and dissolution of precipitates that occur during AM.

In the current study, we propose a modeling approach with appreciably short computational time to investigate the detailed microstructural evolution during metal AM. This may include obtaining more detailed information on the morphologies of phases, such as size distribution, phase fraction, dissolution and nucleation kinetics, as well as chemistry during thermal cycling and final cooling to room temperature. We utilize the combination of the MatCalc thermo-kinetic simulator and a semi-analytical heat conduction model. MatCalc is a software suite for simulation of phase transformations, microstructure evolution and certain mechanical properties in engineering alloys. It has successfully been employed to simulate solid-state phase transformations in Ni-based superalloys [38], [39], steels [40], and Al alloys [41] during complex thermo-mechanical processes. MatCalc uses the classical nucleation theory as well as the so-called Svoboda-Fischer-Fratzl-Kozeschnik (SFFK) growth model as the basis for simulating precipitation kinetics [42]. Although MatCalc was originally developed for conventional thermo-mechanical processes, we will show that it is also applicable for AM if the detailed time-temperature profile of the AM build is known. The semi-analytical heat transfer code developed by Stump and Plotkowski [43] is used to simulate these profile throughout the AM build.

1.1. Application to IN738

Inconel-738 (IN738) is a precipitation hardening Ni-based superalloy mainly employed in high-temperature components, e.g. in gas turbines and aero-engines owing to its exceptional mechanical properties at temperatures up to 980 °C, coupled with high resistance to oxidation and corrosion [44]. Its superior high-temperature strength (∼1090 MPa tensile strength) is provided by the L1₂ ordered Ni₃(Al,Ti) γ′ phase that precipitates in a face-centered cubic (FCC) γ matrix [45], [46]. Despite offering great properties, IN738, like most superalloys with high γ′ fractions, is challenging to process owing to its propensity to hot cracking [47], [48]. Further, machining of such alloys is challenging because of their high strength and work-hardening rates. It is therefore difficult to fabricate complex INC738 parts using traditional manufacturing techniques like casting, welding, and forging.

The emergence of AM has now made it possible to fabricate such parts from IN738 and other superalloys. Some of the current authors’ recent research successfully applied E-PBF to fabricate defect-free IN738 containing γ′ throughout the build [16], [17]. The precipitated γ′ were heterogeneously distributed. In particular, Haghdadi et al. [16] studied the origin of the multimodal size distribution of γ′, while Lim et al. [17] investigated the gradient in γ′ character with build height and its correlation to mechanical properties. Based on these results, the present study aims to extend the understanding of the complex and site-specific microstructural evolution in E-PBF IN738 by using a computational modelling approach. New experimental evidence (e.g., micrographs not published previously) is presented here to support the computational results.

2. Materials and Methods

2.1. Materials preparation

IN738 Ni-based superalloy (59.61Ni-8.48Co-7.00Al-17.47Cr-3.96Ti-1.01Mo-0.81W-0.56Ta-0.49Nb-0.47C-0.09Zr-0.05B, at%) gas-atomized powder was used as feedstock. The powders, with average size of 60 ± 7 µm, were manufactured by Praxair and distributed by Astro Alloys Inc. An Arcam Q10 machine by GE Additive with an acceleration voltage of 60 kV was used to fabricate a 15 × 15 × 25 mm³ block (XYZ, Z: build direction) on a 316 stainless steel substrate. The block was 3D-printed using a ‘random’ spot melt pattern. The random spot melt pattern involves randomly selecting points in any given layer, with an equal chance of each point being melted. Each spot melt experienced a dwell time of 0.3 ms, and the layer thickness was 50 µm. Some of the current authors have previously characterized the microstructure of the very same and similar builds in more detail [16], [17]. A preheat temperature of ∼1000 °C was set and kept during printing to reduce temperature gradients and, in turn, thermal stresses [49], [50], [51]. Following printing, the build was separated from the substrate through electrical discharge machining. It should be noted that this sample was simultaneously printed with the one used in [17] during the same build process and on the same build plate, under identical conditions.

2.2. Microstructural characterization

The printed sample was longitudinally cut in the direction of the build using a Struers Accutom-50, ground, and then polished to 0.25 µm suspension via standard techniques. The polished x-z surface was electropolished and etched using Struers A2 solution (perchloric acid in ethanol). Specimens for image analysis were polished using a 0.06 µm colloidal silica. Microstructure analyses were carried out across the height of the build using optical microscopy (OM) and scanning electron microscopy (SEM) with focus on the microstructure evolution (γ′ precipitates) in individual layers. The position of each layer being analyzed was determined by multiplying the layer number by the layer thickness (50 µm). It should be noted that the position of the first layer starts where the thermal profile is tracked (in this case, 2 mm from the bottom). SEM images were acquired using a JEOL 7001 field emission microscope. The brightness and contrast settings, acceleration voltage of 15 kV, working distance of 10 mm, and other SEM imaging parameters were all held constant for analysis of the entire build. The ImageJ software was used for automated image analysis to determine the phase fraction and size of γ′ precipitates and carbides. A 2-pixel radius Gaussian blur, following a greyscale thresholding and watershed segmentation was used [52]. Primary γ′ sizes (>50 nm), were measured using equivalent spherical diameters. The phase fractions were considered equal to the measured area fraction. Secondary γ′ particles (<50 nm) were not considered here. The γ′ size in the following refers to the diameter of a precipitate.

2.3. Hardness testing

A Struers DuraScan tester was utilized for Vickers hardness mapping on a polished x-z surface, from top to bottom under a maximum load of 100 mN and 10 s dwell time. 30 micro-indentations were performed per row. According to the ASTM standard [53], the indentations were sufficiently distant (∼500 µm) to assure that strain-hardened areas did not interfere with one another.

2.4. Computational simulation of E-PBF IN738 build

2.4.1. Thermal profile modeling

The thermal history was generated using the semi-analytical heat transfer code (also known as the 3DThesis code) developed by Stump and Plotkowski [43]. This code is an open-source C++ program which provides a way to quickly simulate the conductive heat transfer found in welding and AM. The key use case for the code is the simulation of larger domains than is practicable with Computational Fluid Dynamics/Finite Element Analysis programs like FLOW-3D AM. Although simulating conductive heat transfer will not be an appropriate simplification for some investigations (for example the modelling of keyholding or pore formation), the 3DThesis code does provide fast estimates of temperature, thermal gradient, and solidification rate which can be useful for elucidating microstructure formation across entire layers of an AM build. The mathematics involved in the code is as follows:

In transient thermal conduction during welding and AM, with uniform and constant thermophysical properties and without considering fluid convection and latent heat effects, energy conservation can be expressed as:(1)��∂�∂�=�∇2�+�̇where � is density, � specific heat, � temperature, � time, � thermal conductivity, and �̇ a volumetric heat source. By assuming a semi-infinite domain, Eq. 1 can be analytically solved. The solution for temperature at a given time (t) using a volumetric Gaussian heat source is presented as:(2)��,�,�,�−�0=33��32∫0�1��exp−3�′�′2��+�′�′2��+�′�′2��′(3)and��=12��−�′+��2for�=�,�,�(4)and�′�′=�−��′Where � is the vector �,�,� and �� is the location of the heat source.

The numerical integration scheme used is an adaptive Gaussian quadrature method based on the following nondimensionalization:(5)�=��xy2�,�′=��xy2�′,�=��xy,�=��xy,�=��xy,�=��xy

A more detailed explanation of the mathematics can be found in reference [43].

The main source of the thermal cycling present within a powder-bed fusion process is the fusion of subsequent layers. Therefore, regions near the top of a build are expected to undergo fewer thermal cycles than those closer to the bottom. For this purpose, data from the single scan’s thermal influence on multiple layers was spliced to represent the thermal cycles experienced at a single location caused by multiple subsequent layers being fused.

The cross-sectional area simulated by this model was kept constant at 1 × 1 mm², and the depth was dependent on the build location modelled with MatCalc. For a build location 2 mm from the bottom, the maximum number of layers to simulate is 460. Fig. 1a shows a stitched overview OM image of the entire build indicating the region where this thermal cycle is simulated and tracked. To increase similarity with the conditions of the physical build, each thermal history was constructed from the results of two simulations generated with different versions of a random scan path. The parameters used for these thermal simulations can be found in Table 1. It should be noted that the main purpose of the thermal profile modelling was to demonstrate how the conditions at different locations of the build change relative to each other. Accurately predicting the absolute temperature during the build would require validation via a temperature sensor measurement during the build process which is beyond the scope of the study. Nonetheless, to establish the viability of the heat source as a suitable approximation for this study, an additional sensitivity analysis was conducted. This analysis focused on the influence of energy input on γ′ precipitation behavior, the central aim of this paper. This was achieved by employing varying beam absorption energies (0.76, 0.82 – the values utilized in the simulation, and 0.9). The direct impact of beam absorption efficiency on energy input into the material was investigated. Specifically, the initial 20 layers of the build were simulated and subsequently compared to experimental data derived from SEM. While phase fractions were found to be consistent across all conditions, disparities emerged in the mean size of γ′ precipitates. An absorption efficiency of 0.76 yielded a mean size of approximately 70 nm. Conversely, absorption efficiencies of 0.82 and 0.9 exhibited remarkably similar mean sizes of around 130 nm, aligning closely with the outcomes of the experiments.

Table 1. A list of parameters used in thermal simulation of E-PBF.

Parameter	Value
Spatial resolution	5 µm
Time step	0.5 s
Beam diameter	200 µm
Beam penetration depth	1 µm
Beam power	1200 W
Beam absorption efficiency	0.82
Thermal conductivity	25.37 W/(m⋅K)
Chamber temperature	1000 °C
Specific heat	711.756 J/(kg⋅K)
Density	8110 kg/m³

2.4.2. Thermo-kinetic simulation

The numerical analyses of the evolution of precipitates was performed using MatCalc version 6.04 (rel 0.011). The thermodynamic (‘mc_ni.tdb’, version 2.034) and diffusion (‘mc_ni.ddb’, version 2.007) databases were used. MatCalc’s basic principles are elaborated as follows:

The nucleation kinetics of precipitates are computed using a computational technique based on a classical nucleation theory [54] that has been modified for systems with multiple components [42], [55]. Accordingly, the transient nucleation rate (�), which expresses the rate at which nuclei are formed per unit volume and time, is calculated as:(6)�=�0��*∙�xp−�*�∙�∙exp−��where �0 denotes the number of active nucleation sites, �* the rate of atomic attachment, � the Boltzmann constant, � the temperature, �* the critical energy for nucleus formation, τ the incubation time, and t the time. � (Zeldovich factor) takes into consideration that thermal excitation destabilizes the nucleus as opposed to its inactive state [54]. Z is defined as follows:(7)�=−12�kT∂2∆�∂�2�*12where ∆� is the overall change in free energy due to the formation of a nucleus and n is the nucleus’ number of atoms. ∆�’s derivative is evaluated at n* (critical nucleus size). �* accounts for the long-range diffusion of atoms required for nucleation, provided that the matrix’ and precipitates’ composition differ. Svoboda et al. [42] developed an appropriate multi-component equation for �*, which is given by:(8)�*=4��*2�4�∑�=1��ki−�0�2�0��0�−1where �* denotes the critical radius for nucleation, � represents atomic distance, and � is the molar volume. �ki and �0� represent the concentration of elements in the precipitate and matrix, respectively. The parameter �0� denotes the rate of diffusion of the i^th element within the matrix. The expression for the incubation time � is expressed as [54]:(9)�=12�*�2

and �*, which represents the critical energy for nucleation:(10)�*=16�3�3∆�vol2where � is the interfacial energy, and ∆Gvol the change in the volume free energy. The critical nucleus’ composition is similar to the γ′ phase’s equilibrium composition at the same temperature. � is computed based on the precipitate and matrix compositions, using a generalized nearest neighbor broken bond model, with the assumption of interfaces being planar, sharp, and coherent [56], [57], [58].

In Eq. 7, it is worth noting that �* represents the fundamental variable in the nucleation theory. It contains �3/∆�vol2 and is in the exponent of the nucleation rate. Therefore, even small variations in γ and/or ∆�vol can result in notable changes in �, especially if �* is in the order of �∙�. This is demonstrated in [38] for UDIMET 720 Li during continuous cooling, where these quantities change steadily during precipitation due to their dependence on matrix’ and precipitate’s temperature and composition. In the current work, these changes will be even more significant as the system is exposed to multiple cycles of rapid cooling and heating.

Once nucleated, the growth of a precipitate is assessed using the radius and composition evolution equations developed by Svoboda et al. [42] with a mean-field method that employs the thermodynamic extremal principle. The expression for the total Gibbs free energy of a thermodynamic system G, which consists of n components and m precipitates, is given as follows:(11)�=∑��0��0�+∑�=1�4��33��+∑�=1��ki�ki+∑�=1�4��2��.

The chemical potential of component � in the matrix is denoted as �0�(�=1,…,�), while the chemical potential of component � in the precipitate is represented by �ki(�=1,…,�,�=1,…,�). These chemical potentials are defined as functions of the concentrations �ki(�=1,…,�,�=1,…,�). The interface energy density is denoted as �, and �� incorporates the effects of elastic energy and plastic work resulting from the volume change of each precipitate.

Eq. (12) establishes that the total free energy of the system in its current state relies on the independent state variables: the sizes (radii) of the precipitates �� and the concentrations of each component �ki. The remaining variables can be determined by applying the law of mass conservation to each component �. This can be represented by the equation:(12)��=�0�+∑�=1�4��33�ki,

Furthermore, the global mass conservation can be expressed by equation:(13)�=∑�=1��When a thermodynamic system transitions to a more stable state, the energy difference between the initial and final stages is dissipated. This model considers three distinct forms of dissipation effects [42]. These include dissipations caused by the movement of interfaces, diffusion within the precipitate and diffusion within the matrix.

Consequently, �̇� (growth rate) and �̇ki (chemical composition’s rate of change) of the precipitate with index � are derived from the linear system of equation system:(14)�ij��=��where �� symbolizes the rates �̇� and �̇ki [42]. Index i contains variables for precipitate radius, chemical composition, and stoichiometric boundary conditions suggested by the precipitate’s crystal structure. Eq. (10) is computed separately for every precipitate �. For a more detailed description of the formulae for the coefficients �ij and �� employed in this work please refer to [59].

The MatCalc software was used to perform the numerical time integration of �̇� and �̇ki of precipitates based on the classical numerical method by Kampmann and Wagner [60]. Detailed information on this method can be found in [61]. Using this computational method, calculations for E-PBF thermal cycles (cyclic heating and cooling) were computed and compared to experimental data. The simulation took approximately 2–4 hrs to complete on a standard laptop.

3. Results

3.1. Microstructure

Fig. 1 displays a stitched overview image and selected SEM micrographs of various γ′ morphologies and carbides after observations of the X-Z surface of the build from the top to 2 mm above the bottom. Fig. 2 depicts a graph that charts the average size and phase fraction of the primary γ′, as it changes with distance from the top to the bottom of the build. The SEM micrographs show widespread primary γ′ precipitation throughout the entire build, with the size increasing in the top to bottom direction. Particularly, at the topmost height, representing the 460th layer (Z = 22.95 mm), as seen in Fig. 1b, the average size of γ′ is 110 ± 4 nm, exhibiting spherical shapes. This is representative of the microstructure after it solidifies and cools to room temperature, without experiencing additional thermal cycles. The γ′ size slightly increases to 147 ± 6 nm below this layer and remains constant until 0.4 mm (∼453rd layer) from the top. At this position, the microstructure still closely resembles that of the 460th layer. After the 453rd layer, the γ′ size grows rapidly to ∼503 ± 19 nm until reaching the 437th layer (1.2 mm from top). The γ′ particles here have a cuboidal shape, and a small fraction is coarser than 600 nm. γ′ continue to grow steadily from this position to the bottom (23 mm from the top). A small fraction of γ′ is > 800 nm.

Besides primary γ′, secondary γ′ with sizes ranging from 5 to 50 nm were also found. These secondary γ′ precipitates, as seen in Fig. 1f, were present only in the bottom and middle regions. A detailed analysis of the multimodal size distribution of γ′ can be found in [16]. There is no significant variation in the phase fraction of the γ′ along the build. The phase fraction is ∼ 52%, as displayed in Fig. 2. It is worth mentioning that the total phase fraction of γ′ was estimated based on the primary γ′ phase fraction because of the small size of secondary γ′. Spherical MC carbides with sizes ranging from 50 to 400 nm and a phase fraction of 0.8% were also observed throughout the build. The carbides are the light grey precipitates in Fig. 1g. The light grey shade of carbides in the SEM images is due to their composition and crystal structure [52]. These carbides are not visible in Fig. 1b-e because they were dissolved during electro-etching carried out after electropolishing. In Fig. 1g, however, the sample was examined directly after electropolishing, without electro-etching.

Table 2 shows the nominal and measured composition of γ′ precipitates throughout the build by atom probe microscopy as determined in our previous study [17]. No build height-dependent composition difference was observed in either of the γ′ precipitate populations. However, there was a slight disparity between the composition of primary and secondary γ′. Among the main γ′ forming elements, the primary γ′ has a high Ti concentration while secondary γ′ has a high Al concentration. A detailed description of the atom distribution maps and the proxigrams of the constituent elements of γ′ throughout the build can be found in [17].

Table 2. Bulk IN738 composition determined using inductively coupled plasma atomic emission spectroscopy (ICP-AES). Compositions of γ, primary γ′, and secondary γ′ at various locations in the build measured by APT. This information is reproduced from data in Ref. [17] with permission.

at%	Ni	Cr	Co	Al	Mo	W	Ti	Nb	C	B	Zr	Ta	Others
Bulk	59.12	17.47	8.48	7.00	1.01	0.81	3.96	0.49	0.47	0.05	0.09	0.56	0.46
γ matrix
Top	50.48	32.91	11.59	1.94	1.39	0.82	0.44	0.8	0.03	0.03	0.02	–	0.24
Mid	50.37	32.61	11.93	1.79	1.54	0.89	0.44	0.1	0.03	0.02	0.02	0.01	0.23
Bot	48.10	34.57	12.08	2.14	1.43	0.88	0.48	0.08	0.04	0.03	0.01	–	0.12
Primary γ′
Top	72.17	2.51	3.44	12.71	0.25	0.39	7.78	0.56	–	0.03	0.02	0.05	0.08
Mid	71.60	2.57	3.28	13.55	0.42	0.68	7.04	0.73	–	0.01	0.03	0.04	0.04
Bot	72.34	2.47	3.86	12.50	0.26	0.44	7.46	0.50	0.05	0.02	0.02	0.03	0.04
Secondary γ′
Mid	70.42	4.20	3.23	14.19	0.63	1.03	5.34	0.79	0.03	–	0.04	0.04	0.05
Bot	69.91	4.06	3.68	14.32	0.81	1.04	5.22	0.65	0.05	–	0.10	0.02	0.11

3.2. Hardness

Fig. 3a shows the Vickers hardness mapping performed along the entire X-Z surface, while Fig. 3b shows the plot of average hardness at different build heights. This hardness distribution is consistent with the γ′ precipitate size gradient across the build direction in Fig. 1, Fig. 2. The maximum hardness of ∼530 HV1 is found at ∼0.5 mm away from the top surface (Z = 22.5), where γ′ particles exhibit the smallest observed size in Fig. 2b. Further down the build (∼ 2 mm from the top), the hardness drops to the 440–490 HV1 range. This represents the region where γ′ begins to coarsen. The hardness drops further to 380–430 HV1 at the bottom of the build.

3.3. Modeling of the microstructural evolution during E-PBF

3.3.1. Thermal profile modeling

Fig. 4 shows the simulated thermal profile of the E-PBF build at a location of 23 mm from the top of the build, using a semi-analytical heat conduction model. This profile consists of the time taken to deposit 460 layers until final cooling, as shown in Fig. 4a. Fig. 4b-d show the magnified regions of Fig. 4a and reveal the first 20 layers from the top, a single layer (first layer from the top), and the time taken for the build to cool after the last layer deposition, respectively.

The peak temperatures experienced by previous layers decrease progressively as the number of layers increases but never fall below the build preheat temperature (1000 °C). Our simulated thermal cycle may not completely capture the complexity of the actual thermal cycle utilized in the E-PBF build. For instance, the top layer (Fig. 4c), also representing the first deposit’s thermal profile without additional cycles (from powder heating, melting, to solidification), recorded the highest peak temperature of 1390 °C. Although this temperature is above the melting range of the alloy (1230–1360 °C) [62], we believe a much higher temperature was produced by the electron beam to melt the powder. Nevertheless, the solidification temperature and dynamics are outside the scope of this study as our focus is on the solid-state phase transformations during deposition. It takes ∼25 s for each layer to be deposited and cooled to the build temperature. The interlayer dwell time is 125 s. The time taken for the build to cool to room temperature (RT) after final layer deposition is ∼4.7 hrs (17,000 s).

3.3.2. MatCalc simulation

During the MatCalc simulation, the matrix phase is defined as γ. γ′, and MC carbide are included as possible precipitates. The domain of these precipitates is set to be the matrix (γ), and nucleation is assumed to be homogenous. In homogeneous nucleation, all atoms of the unit volume are assumed to be potential nucleation sites. Table 3 shows the computational parameters used in the simulation. All other parameters were set at default values as recommended in the version 6.04.0011 of MatCalc. The values for the interfacial energies are automatically calculated according to the generalized nearest neighbor broken bond model and is one of the most outstanding features in MatCalc [56], [57], [58]. It should be noted that the elastic misfit strain was not included in the calculation. The output of MatCalc includes phase fraction, size, nucleation rate, and composition of the precipitates. The phase fraction in MatCalc is the volume fraction. Although the experimental phase fraction is the measured area fraction, it is relatively similar to the volume fraction. This is because of the generally larger precipitate size and similar morphology at the various locations along the build [63]. A reliable phase fraction comparison between experiment and simulation can therefore be made.

Table 3. Computational parameters used in the simulation.

Precipitation domain	γ
Nucleation site γ′	Bulk (homogenous)
Nucleation site MC carbide	Bulk (Homogenous)
Precipitates class size	250
Regular solution critical temperature γ′	2500 K[64]
Calculated interfacial energy	γ′ = 0.080–0.140 J/m² and MC carbide = 0.410–0.430 J/m²

3.3.2.1. Precipitate phase fraction

Fig. 5a shows the simulated phase fraction of γ′ and MC carbide during thermal cycling. Fig. 5b is a magnified view of 5a showing the simulated phase fraction at the center points of the top 70 layers, whereas Fig. 5c corresponds to the first two layers from the top. As mentioned earlier, the top layer (460th layer) represents the microstructure after solidification. The microstructure of the layers below is determined by the number of thermal cycles, which increases with distance to the top. For example, layers 459, 458, 457, up to layer 1 (region of interest) experience 1, 2, 3 and 459 thermal cycles, respectively. In the top layer in Fig. 5c, the volume fraction of γ′ and carbides increases with temperature. For γ′, it decreases to zero when the temperature is above the solvus temperature after a few seconds. Carbides, however, remain constant in their volume fraction reaching equilibrium (phase fraction ∼ 0.9%) in a short time. The topmost layer can be compared to the first deposit, and the peak in temperature symbolizes the stage where the electron beam heats the powder until melting. This means γ′ and carbide precipitation might have started in the powder particles during heating from the build temperature and electron beam until the onset of melting, where γ′ dissolves, but carbides remain stable [28].

During cooling after deposition, γ′ reprecipitates at a temperature of 1085 °C, which is below its solvus temperature. As cooling progresses, the phase fraction increases steadily to ∼27% and remains constant at 1000 °C (elevated build temperature). The calculated equilibrium fraction of phases by MatCalc is used to show the complex precipitation characteristics in this alloy. Fig. 6 shows that MC carbides form during solidification at 1320 °C, followed by γ′, which precipitate when the solidified layer cools to 1140 °C. This indicates that all deposited layers might contain a negligible amount of these precipitates before subsequent layer deposition, while being at the 1000 °C build temperature or during cooling to RT. The phase diagram also shows that the equilibrium fraction of the γ′ increases as temperature decreases. For instance, at 1000, 900, and 800 °C, the phase fractions are ∼30%, 38%, and 42%, respectively.

Deposition of subsequent layers causes previous layers to undergo phase transformations as they are exposed to several thermal cycles with different peak temperatures. In Fig. 5c, as the subsequent layer is being deposited, γ′ in the previous layer (459th layer) begins to dissolve as the temperature crosses the solvus temperature. This is witnessed by the reduction of the γ′ phase fraction. This graph also shows how this phase dissolves during heating. However, the phase fraction of MC carbide remains stable at high temperatures and no dissolution is seen during thermal cycling. Upon cooling, the γ′ that was dissolved during heating reprecipitates with a surge in the phase fraction until 1000 °C, after which it remains constant. This microstructure is similar to the solidification microstructure (layer 460), with a similar γ′ phase fraction (∼27%).

The complete dissolution and reprecipitation of γ′ continue for several cycles until the 50th layer from the top (layer 411), where the phase fraction does not reach zero during heating to the peak temperature (see Fig. 5d). This indicates the ‘partial’ dissolution of γ′, which continues progressively with additional layers. It should be noted that the peak temperatures for layers that underwent complete dissolution were much higher (1170–1300 °C) than the γ′ solvus.

The dissolution and reprecipitation of γ′ during thermal cycling are further confirmed in Fig. 7, which summarizes the nucleation rate, phase fraction, and concentration of major elements that form γ′ in the matrix. Fig. 7b magnifies a single layer (3rd layer from top) within the full dissolution region in Fig. 7a to help identify the nucleation and growth mechanisms. From Fig. 7b, γ′ nucleation begins during cooling whereby the nucleation rate increases to reach a maximum value of approximately 1 × 10²⁰ m⁻³s⁻¹. This fast kinetics implies that some rearrangement of atoms is required for γ′ precipitates to form in the matrix [65], [66]. The matrix at this stage is in a non-equilibrium condition. Its composition is similar to the nominal composition and remains unchanged. The phase fraction remains insignificant at this stage although nucleation has started. The nucleation rate starts declining upon reaching the peak value. Simultaneously, diffusion-controlled growth of existing nuclei occurs, depleting the matrix of γ′ forming elements (Al and Ti). Thus, from (7), (11), ∆�vol continuously decreases until nucleation ceases. The growth of nuclei is witnessed by the increase in phase fraction until a constant level is reached at 27% upon cooling to and holding at build temperature. This nucleation event is repeated several times.

At the onset of partial dissolution, the nucleation rate jumps to 1 × 10²¹ m⁻³s⁻¹, and then reduces sharply at the middle stage of partial dissolution. The nucleation rate reaches 0 at a later stage. Supplementary Fig. S1 shows a magnified view of the nucleation rate, phase fraction, and thermal profile, underpinning this trend. The jump in nucleation rate at the onset is followed by a progressive reduction in the solute content of the matrix. The peak temperatures (∼1130–1160 °C) are lower than those in complete dissolution regions but still above or close to the γ′ solvus. The maximum phase fraction (∼27%) is similar to that of the complete dissolution regions. At the middle stage, the reduction in nucleation rate is accompanied by a sharp drop in the matrix composition. The γ′ fraction drops to ∼24%, where the peak temperatures of the layers are just below or at γ′ solvus. The phase fraction then increases progressively through the later stage of partial dissolution to ∼30% towards the end of thermal cycling. The matrix solute content continues to drop although no nucleation event is seen. The peak temperatures are then far below the γ′ solvus. It should be noted that the matrix concentration after complete dissolution remains constant. Upon cooling to RT after final layer deposition, the nucleation rate increases again, indicating new nucleation events. The phase fraction reaches ∼40%, with a further depletion of the matrix in major γ′ forming elements.

3.3.2.2. γ′ size distribution

Fig. 8 shows histograms of the γ′ precipitate size distributions (PSD) along the build height during deposition. These PSDs are predicted at the end of each layer of interest just before final cooling to room temperature, to separate the role of thermal cycles from final cooling on the evolution of γ′. The PSD for the top layer (layer 460) is shown in Fig. 8a (last solidified region with solidification microstructure). The γ′ size ranges from 120 to 230 nm and is similar to the 44 layers below (2.2 mm from the top).

Further down the build, γ′ begins to coarsen after layer 417 (44th layer from top). Fig. 8c shows the PSD after the 44th layer, where the γ′ size exhibits two peaks at ∼120–230 and ∼300 nm, with most of the population being in the former range. This is the onset of partial dissolution where simultaneously with the reprecipitation and growth of fresh γ′, the undissolved γ′ grows rapidly through diffusive transport of atoms to the precipitates. This is shown in Fig. 8c, where the precipitate class sizes between 250 and 350 represent the growth of undissolved γ′. Although this continues in the 416th layer, the phase fractions plot indicates that the onset of partial dissolution begins after the 411th layer. This implies that partial dissolution started early, but the fraction of undissolved γ′ was too low to impact the phase fraction. The reprecipitated γ′ are mostly in the 100–220 nm class range and similar to those observed during full dissolution.

As the number of layers increases, coarsening intensifies with continued growth of more undissolved γ′, and reprecipitation and growth of partially dissolved ones. Fig. 8d, e, and f show this sequence. Further down the build, coarsening progresses rapidly, as shown in Figs. 8d, 8e, and 8f. The γ′ size ranges from 120 to 1100 nm, with the peaks at 160, 180, and 220 nm in Figs. 8d, 8e, and 8f, respectively. Coarsening continues until nucleation ends during dissolution, where only the already formed γ′ precipitates continue to grow during further thermal cycling. The γ′ size at this point is much larger, as observed in layers 361 and 261, and continues to increase steadily towards the bottom (layer 1). Two populations in the ranges of ∼380–700 and ∼750–1100 nm, respectively, can be seen. The steady growth of γ′ towards the bottom is confirmed by the gradual decrease in the concentration of solute elements in the matrix (Fig. 7a). It should be noted that for each layer, the γ′ class with the largest size originates from continuous growth of the earliest set of the undissolved precipitates.

Fig. 9, Fig. 10 and supplementary Figs. S2 and S3 show the γ′ size evolution during heating and cooling of a single layer in the full dissolution region, and early, middle stages, and later stages of partial dissolution, respectively. In all, the size of γ′ reduces during layer heating. Depending on the peak temperature of the layer which varies with build height, γ′ are either fully or partially dissolved as mentioned earlier. Upon cooling, the dissolved γ′ reprecipitate.

In Fig. 9, those layers that underwent complete dissolution (top layers) were held above γ′ solvus temperature for longer. In Fig. 10, layers at the early stage of partial dissolution spend less time in the γ′ solvus temperature region during heating, leading to incomplete dissolution. In such conditions, smaller precipitates are fully dissolved while larger ones shrink [67]. Layers in the middle stages of partial dissolution have peak temperatures just below or at γ′ solvus, not sufficient to achieve significant γ′ dissolution. As seen in supplementary Fig. S2, only a few smaller γ′ are dissolved back into the matrix during heating, i.e., growth of precipitates is more significant than dissolution. This explains the sharp decrease in concentration of Al and Ti in the matrix in this layer.

The previous sections indicate various phenomena such as an increase in phase fraction, further depletion of matrix composition, and new nucleation bursts during cooling. Analysis of the PSD after the final cooling of the build to room temperature allows a direct comparison to post-printing microstructural characterization. Fig. 11 shows the γ′ size distribution of layer 1 (460th layer from the top) after final cooling to room temperature. Precipitation of secondary γ′ is observed, leading to the multimodal size distribution of secondary and primary γ′. The secondary γ′ size falls within the 10–80 nm range. As expected, a further growth of the existing primary γ′ is also observed during cooling.

3.3.2.3. γ′ chemistry after deposition

Fig. 12 shows the concentration of the major elements that form γ′ (Al, Ti, and Ni) in the primary and secondary γ′ at the bottom of the build, as calculated by MatCalc. The secondary γ′ has a higher Al content (13.5–14.5 at% Al), compared to 13 at% Al in the primary γ′. Additionally, within the secondary γ′, the smallest particles (∼10 nm) have higher Al contents than larger ones (∼70 nm). In contrast, for the primary γ′, there is no significant variation in the Al content as a function of their size. The Ni concentration in secondary γ′ (71.1–72 at%) is also higher in comparison to the primary γ′ (70 at%). The smallest secondary γ′ (∼10 nm) have higher Ni contents than larger ones (∼70 nm), whereas there is no substantial change in the Ni content of primary γ′, based on their size. As expected, Ti shows an opposite size-dependent variation. It ranges from ∼ 7.7–8.7 at% Ti in secondary γ′ to ∼9.2 at% in primary γ′. Similarly, within the secondary γ′, the smallest (∼10 nm) have lower Al contents than the larger ones (∼70 nm). No significant variation is observed for Ti content in primary γ′.

4. Discussion

A combined modelling method is utilized to study the microstructural evolution during E-PBF of IN738. The presented results are discussed by examining the precipitation and dissolution mechanism of γ′ during thermal cycling. This is followed by a discussion on the phase fraction and size evolution of γ′ during thermal cycling and after final cooling. A brief discussion on carbide morphology is also made. Finally, a comparison is made between the simulation and experimental results to assess their agreement.

4.1. γ′ morphology as a function of build height

4.1.1. Nucleation of γ′

The fast precipitation kinetics of the γ′ phase enables formation of γ′ upon quenching from higher temperatures (above solvus) during thermal cycling [66]. In Fig. 7b, for a single layer in the full dissolution region, during cooling, the initial increase in nucleation rate signifies the first formation of nuclei. The slight increase in nucleation rate during partial dissolution, despite a decrease in the concentration of γ′ forming elements, may be explained by the nucleation kinetics. During partial dissolution and as the precipitates shrink, it is assumed that the regions at the vicinity of partially dissolved precipitates are enriched in γ′ forming elements [68], [69]. This differs from the full dissolution region, in which case the chemical composition is evenly distributed in the matrix. Several authors have attributed the solute supersaturation of the matrix around primary γ′ to partial dissolution during isothermal ageing [69], [70], [71], [72]. The enhanced supersaturation in the regions close to the precipitates results in a much higher driving force for nucleation, leading to a higher nucleation rate upon cooling. This phenomenon can be closely related to the several nucleation bursts upon continuous cooling of Ni-based superalloys, where second nucleation bursts exhibit higher nucleation rates [38], [68], [73], [74].

At middle stages of partial dissolution, the reduction in the nucleation rate indicates that the existing composition and low supersaturation did not trigger nucleation as the matrix was closer to the equilibrium state. The end of a nucleation burst means that the supersaturation of Al and Ti has reached a low level, incapable of providing sufficient driving force during cooling to or holding at 1000 °C for further nucleation [73]. Earlier studies on Ni-based superalloys have reported the same phenomenon during ageing or continuous cooling from the solvus temperature to RT [38], [73], [74].

4.1.2. Dissolution of γ′ during thermal cycling

γ′ dissolution kinetics during heating are fast when compared to nucleation due to exponential increase in phase transformation and diffusion activities with temperature [65]. As shown in Fig. 9, Fig. 10, and supplementary Figs. S2 and S3, the reduction in γ′ phase fraction and size during heating indicates γ′ dissolution. This is also revealed in Fig. 5 where phase fraction decreases upon heating. The extent of γ′ dissolution mostly depends on the temperature, time spent above γ′ solvus, and precipitate size [75], [76], [77]. Smaller γ′ precipitates are first to be dissolved [67], [77], [78]. This is mainly because more solute elements need to be transported away from large γ′ precipitates than from smaller ones [79]. Also, a high temperature above γ′ solvus temperature leads to a faster dissolution rate [80]. The equilibrium solvus temperature of γ′ in IN738 in our MatCalc simulation (Fig. 6) and as reported by Ojo et al. [47] is 1140 °C and 1130–1180 °C, respectively. This means the peak temperature experienced by previous layers decreases progressively from γ′ supersolvus to subsolvus, near-solvus, and far from solvus as the number of subsequent layers increases. Based on the above, it can be inferred that the degree of dissolution of γ′ contributes to the gradient in precipitate distribution.

Although the peak temperatures during later stages of partial dissolution are much lower than the equilibrium γ′ solvus, γ′ dissolution still occurs but at a significantly lower rate (supplementary Fig. S3). Wahlmann et al. [28] also reported a similar case where they observed the rapid dissolution of γ′ in CMSX-4 during fast heating and cooling cycles at temperatures below the γ′ solvus. They attributed this to the γ′ phase transformation process taking place in conditions far from the equilibrium. While the same reasoning may be valid for our study, we further believe that the greater surface area to volume ratio of the small γ′ precipitates contributed to this. This ratio means a larger area is available for solute atoms to diffuse into the matrix even at temperatures much below the solvus [81].

4.2. γ′ phase fraction and size evolution

4.2.1. During thermal cycling

In the first layer, the steep increase in γ′ phase fraction during heating (Fig. 5), which also represents γ′ precipitation in the powder before melting, has qualitatively been validated in [28]. The maximum phase fraction of 27% during the first few layers of thermal cycling indicates that IN738 theoretically could reach the equilibrium state (∼30%), but the short interlayer time at the build temperature counteracts this. The drop in phase fraction at middle stages of partial dissolution is due to the low number of γ′ nucleation sites [73]. It has been reported that a reduction of γ′ nucleation sites leads to a delay in obtaining the final volume fraction as more time is required for γ′ precipitates to grow and reach equilibrium [82]. This explains why even upon holding for 150 s before subsequent layer deposition, the phase fraction does not increase to those values that were observed in the previous full γ′ dissolution regions. Towards the end of deposition, the increase in phase fraction to the equilibrium value of 30% is as a result of the longer holding at build temperature or close to it [83].

During thermal cycling, γ′ particles begin to grow immediately after they first precipitate upon cooling. This is reflected in the rapid increase in phase fraction and size during cooling in Fig. 5 and supplementary Fig. S2, respectively. The rapid growth is due to the fast diffusion of solute elements at high temperatures [84]. The similar size of γ′ for the first 44 layers from the top can be attributed to the fact that all layers underwent complete dissolution and hence, experienced the same nucleation event and growth during deposition. This corresponds with the findings by Balikci et al. [85], who reported that the degree of γ′ precipitation in IN738LC does not change when a solution heat treatment is conducted above a certain critical temperature.

The increase in coarsening rate (Fig. 8) during thermal cycling can first be ascribed to the high peak temperature of the layers [86]. The coarsening rate of γ′ is known to increase rapidly with temperature due to the exponential growth of diffusion activity. Also, the simultaneous dissolution with coarsening could be another reason for the high coarsening rate, as γ′ coarsening is a diffusion-driven process where large particles grow by consuming smaller ones [78], [84], [86], [87]. The steady growth of γ′ towards the bottom of the build is due to the much lower layer peak temperature, which is almost close to the build temperature, and reduced dissolution activity, as is seen in the much lower solute concentration in γ′ compared to those in the full and partial dissolution regions.

4.2.2. During cooling

The much higher phase fraction of ∼40% upon cooling signifies the tendency of γ′ to reach equilibrium at lower temperatures (Fig. 4). This is due to the precipitation of secondary γ′ and a further increase in the size of existing primary γ′, which leads to a multimodal size distribution of γ′ after cooling [38], [73], [88], [89], [90]. The reason for secondary γ′ formation during cooling is as follows: As cooling progresses, it becomes increasingly challenging to redistribute solute elements in the matrix owing to their lower mobility [38], [73]. A higher supersaturation level in regions away from or free of the existing γ′ precipitates is achieved, making them suitable sites for additional nucleation bursts. More cooling leads to the growth of these secondary γ′ precipitates, but as the temperature and in turn, the solute diffusivity is low, growth remains slow.

4.3. Carbides

MC carbides in IN738 are known to have a significant impact on the high-temperature strength. They can also act as effective hardening particles and improve the creep resistance [91]. Precipitation of MC carbides in IN738 and several other superalloys is known to occur during solidification or thermal treatments (e.g., hot isostatic pressing) [92]. In our case, this means that the MC carbides within the E-PBF build formed because of the thermal exposure from the E-PBF thermal cycle in addition to initial solidification. Our simulation confirms this as MC carbides appear during layer heating (Fig. 5). The constant and stable phase fraction of MC carbides during thermal cycling can be attributed to their high melting point (∼1360 °C) and the short holding time at peak temperatures [75], [93], [94]. The solvus temperature for most MC carbides exceeds most of the peak temperatures observed in our simulation, and carbide dissolution kinetics at temperatures above the solvus are known to be comparably slow [95]. The stable phase fraction and random distribution of MC carbides signifies the slight influence on the gradient in hardness.

4.4. Comparison of simulations and experiments

4.4.1. Precipitate phase fraction and morphology as a function of build height

A qualitative agreement is observed for the phase fraction of carbides, i.e. ∼0.8% in the experiment and ∼0.9% in the simulation. The phase fraction of γ′ differs, with the experiment reporting a value of ∼51% and the simulation, 40%. Despite this, the size distribution of primary γ′ along the build shows remarkable consistency between experimental and computational analyses. It is worth noting that the primary γ′ morphology in the experimental analysis is observed in the as-fabricated state, whereas the simulation (Fig. 8) captures it during deposition process. The primary γ′ size in the experiment is expected to experience additional growth during the cooling phase. Regardless, both show similar trends in primary γ′ size increments from the top to the bottom of the build. The larger primary γ’ size in the simulation versus the experiment can be attributed to the fact that experimental and simulation results are based on 2D and 3D data, respectively. The absence of stereological considerations [96] in our analysis could have led to an underestimation of the precipitate sizes from SEM measurements. The early starts of coarsening (8th layer) in the experiment compared to the simulation (45th layer) can be attributed to a higher actual γ′ solvus temperature than considered in our simulation [47]. The solvus temperature of γ′ in a Ni-based superalloy is mainly determined by the detailed composition. A high amount of Cr and Co are known to reduce the solvus temperature, whereas Ta and Mo will increase it [97], [98], [99]. The elemental composition from our experimental work was used for the simulation except for Ta. It should be noted that Ta is not included in the thermodynamic database in MatCalc used, and this may have reduced the solvus temperature. This could also explain the relatively higher γ′ phase fraction in the experiment than in simulation, as a higher γ′ solvus temperature will cause more γ′ to precipitate and grow early during cooling [99], [100].

Another possible cause of this deviation can be attributed to the extent of γ′ dissolution, which is mainly determined by the peak temperature. It can be speculated that individual peak temperatures at different layers in the simulation may have been over-predicted. However, one needs to consider that the true thermal profile is likely more complicated in the actual E-PBF process [101]. For example, the current model assumes that the thermophysical properties of the material are temperature-independent, which is not realistic. Many materials, including IN738, exhibit temperature-dependent properties such as thermal conductivity, specific heat capacity, and density [102]. This means that heat transfer simulations may underestimate or overestimate the temperature gradients and cooling rates within the powder bed and the solidified part. Additionally, the model does not account for the reduced thermal diffusivity through unmelted powder, where gas separating the powder acts as insulation, impeding the heat flow [1]. In E-PBF, the unmelted powder regions with trapped gas have lower thermal diffusivity compared to the fully melted regions, leading to localized temperature variations, and altered solidification behavior. These limitations can impact the predictions, particularly in relation to the carbide dissolution, as the peak temperatures may be underestimated.

While acknowledging these limitations, it is worth emphasizing that achieving a detailed and accurate representation of each layer’s heat source would impose tough computational challenges. Given the substantial layer count in E-PBF, our decision to employ a semi-analytical approximation strikes a balance between computational feasibility and the capture of essential trends in thermal profiles across diverse build layers. In future work, a dual-calibration strategy is proposed to further reduce simulation-experiment disparities. By refining temperature-independent thermophysical property approximations and absorptivity in the heat source model, and by optimizing interfacial energy descriptions in the kinetic model, the predictive precision could be enhanced. Further refining the simulation controls, such as adjusting the precipitate class size may enhance quantitative comparisons between modeling outcomes and experimental data in future work.

4.4.2. Multimodal size distribution of γ′ and concentration

Another interesting feature that sees qualitative agreement between the simulation and the experiment is the multimodal size distribution of γ′. The formation of secondary γ′ particles in the experiment and most E-PBF Ni-based superalloys is suggested to occur at low temperatures, during final cooling to RT [16], [73], [90]. However, so far, this conclusion has been based on findings from various continuous cooling experiments, as the study of the evolution during AM would require an in-situ approach. Our simulation unambiguously confirms this in an AM context by providing evidence for secondary γ′ precipitation during slow cooling to RT. Additionally, it is possible to speculate that the chemical segregation occurring during solidification, due to the preferential partitioning of certain elements between the solid and liquid phases, can contribute to the multimodal size distribution during deposition [51]. This is because chemical segregation can result in variations in the local composition of superalloys, which subsequently affects the nucleation and growth of γ′. Regions with higher concentrations of alloying elements will encourage the formation of larger γ′ particles, while regions with lower concentrations may favor the nucleation of smaller precipitates. However, it is important to acknowledge that the elevated temperature during the E-PBF process will largely homogenize these compositional differences [103], [104].

A good correlation is also shown in the composition of major γ′ forming elements (Al and Ti) in primary and secondary γ′. Both experiment and simulation show an increasing trend for Al content and a decreasing trend for Ti content from primary to secondary γ′. The slight composition differences between primary and secondary γ′ particles are due to the different diffusivity of γ′ stabilizers at different thermal conditions [105], [106]. As the formation of multimodal γ′ particles with different sizes occurs over a broad temperature range, the phase chemistry of γ′ will be highly size dependent. The changes in the chemistry of various γ′ (primary, secondary, and tertiary) have received significant attention since they have a direct influence on the performance [68], [105], [107], [108], [109]. Chen et al. [108], [109], reported a high Al content in the smallest γ′ precipitates compared to the largest, while Ti showed an opposite trend during continuous cooling in a RR1000 Ni-based superalloy. This was attributed to the temperature and cooling rate at which the γ′ precipitates were formed. The smallest precipitates formed last, at the lowest temperature and cooling rate. A comparable observation is evident in the present investigation, where the secondary γ′ forms at a low temperature and cooling rate in comparison to the primary. The temperature dependence of γ′ chemical composition is further evidenced in supplementary Fig. S4, which shows the equilibrium chemical composition of γ′ as a function of temperature.

5. Conclusions

A correlative modelling approach capable of predicting solid-state phase transformations kinetics in metal AM was developed. This approach involves computational simulations with a semi-analytical heat transfer model and the MatCalc thermo-kinetic software. The method was used to predict the phase transformation kinetics and detailed morphology and chemistry of γ′ and MC during E-PBF of IN738 Ni-based superalloy. The main conclusions are:

1.The computational simulations are in qualitative agreement with the experimental observations. This is particularly true for the γ′ size distribution along the build height, the multimodal size distribution of particles, and the phase fraction of MC carbides.
2.The deviations between simulation and experiment in terms of γ′ phase fraction and location in the build are most likely attributed to a higher γ′ solvus temperature during the experiment than in the simulation, which is argued to be related to the absence of Ta in the MatCalc database.
3.The dissolution and precipitation of γ′ occur fast and under non-equilibrium conditions. The level of γ′ dissolution determines the gradient in γ′ size distribution along the build. After thermal cycling, the final cooling to room temperature has further significant impacts on the final γ′ size, morphology, and distribution.
4.A negligible amount of γ′ forms in the first deposited layer before subsequent layer deposition, and a small amount of γ′ may also form in the powder induced by the 1000 °C elevated build temperature before melting.

Our findings confirm the suitability of MatCalc to predict the microstructural evolution at various positions throughout a build in a Ni-based superalloy during E-PBF. It also showcases the suitability of a tool which was originally developed for traditional thermo-mechanical processing of alloys to the new additive manufacturing context. Our simulation capabilities are likely extendable to other alloy systems that undergo solid-state phase transformations implemented in MatCalc (various steels, Ni-based superalloys, and Al-alloys amongst others) as well as other AM processes such as L-DED and L-PBF which have different thermal cycle characteristics. New tools to predict the microstructural evolution and properties during metal AM are important as they provide new insights into the complexities of AM. This will enable control and design of AM microstructures towards advanced materials properties and performances.

CRediT authorship contribution statement

Primig Sophie: Writing – review & editing, Supervision, Resources, Project administration, Funding acquisition, Conceptualization. Adomako Nana Kwabena: Writing – original draft, Writing – review & editing, Visualization, Software, Investigation, Formal analysis, Conceptualization. Haghdadi Nima: Writing – review & editing, Supervision, Project administration, Methodology, Conceptualization. Dingle James F.L.: Methodology, Conceptualization, Software, Writing – review & editing, Visualization. Kozeschnik Ernst: Writing – review & editing, Software, Methodology. Liao Xiaozhou: Writing – review & editing, Project administration, Funding acquisition. Ringer Simon P: Writing – review & editing, Project administration, Funding acquisition.

Declaration of Competing Interest

The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper.

Acknowledgements

This research was sponsored by the Department of Industry, Innovation, and Science under the auspices of the AUSMURI program – which is a part of the Commonwealth’s Next Generation Technologies Fund. The authors acknowledge the facilities and the scientific and technical assistance at the Electron Microscope Unit (EMU) within the Mark Wainwright Analytical Centre (MWAC) at UNSW Sydney and Microscopy Australia. Nana Adomako is supported by a UNSW Scientia PhD scholarship. Michael Haines’ (UNSW Sydney) contribution to the revised version of the original manuscript is thankfully acknowledged.

Appendix A. Supplementary material

Download : Download Word document (462KB)

Supplementary material.

Data Availability

Data will be made available on request.

References

[1]T. Debroy, H.L. Wei, J.S. Zuback, T. Mukherjee, J.W. Elmer, J.O. Milewski, A.M. Beese, A. Wilson-heid, A. De, W. ZhangAdditive manufacturing of metallic components – process, structure and propertiesProg. Mater. Sci., 92 (2018), pp. 112-224, 10.1016/j.pmatsci.2017.10.001 View PDF View article View in Scopus Google Scholar
[2]S. Li, Q. Wei, Y. Shi, C.K. Chua, Z. Zhu, D. ZhangMicrostructure characteristics of Inconel 625 superalloy manufactured by selective laser meltingJ. Mater. Sci. Technol., 31 (2015), pp. 946-952, 10.1016/j.jmst.2014.09.020 View PDF View article View in Scopus Google Scholar
[3]M. Gäumann, C. Bezençon, P. Canalis, W. KurzSingle-crystal laser deposition of superalloys: processing-microstructure mapsActa Mater., 49 (2001), pp. 1051-1062, 10.1016/S1359-6454(00)00367-0 View PDF View article View in Scopus Google Scholar
[4]N.K. Adomako, J.J. Lewandowski, B.M. Arkhurst, H. Choi, H.J. Chang, J.H. KimMicrostructures and mechanical properties of multi-layered materials composed of Ti-6Al-4V, vanadium, and 17–4PH stainless steel produced by directed energy depositionAddit. Manuf., 59 (2022), Article 103174, 10.1016/j.addma.2022.103174 View PDF View article View in Scopus Google Scholar
[5]H. Wang, Z.G. Zhu, H. Chen, A.G. Wang, J.Q. Liu, H.W. Liu, R.K. Zheng, S.M.L. Nai, S. Primig, S.S. Babu, S.P. Ringer, X.Z. LiaoEffect of cyclic rapid thermal loadings on the microstructural evolution of a CrMnFeCoNi high-entropy alloy manufactured by selective laser meltingActa Mater., 196 (2020), pp. 609-625, 10.1016/J.ACTAMAT.2020.07.006 View PDF View article View in Scopus Google Scholar
[6]N. Kwabena Adomako, N. Haghdadi, S. PrimigElectron and laser-based additive manufacturing of Ni-based superalloys: a review of heterogeneities in microstructure and mechanical propertiesMater. Des., 223 (2022), Article 111245, 10.1016/J.MATDES.2022.111245 View PDF View article View in Scopus Google Scholar
[7]S.H. Sun, Y. Koizumi, S. Kurosu, Y.P. Li, H. Matsumoto, A. ChibaBuild direction dependence of microstructure and high-temperature tensile property of Co-Cr-Mo alloy fabricated by electron beam meltingActa Mater., 64 (2014), pp. 154-168, 10.1016/j.actamat.2013.10.017 View PDF View article View in Scopus Google Scholar
[8]S.H. Sun, Y. Koizumi, S. Kurosu, Y.P. Li, A. ChibaPhase and grain size inhomogeneity and their influences on creep behavior of Co-Cr-Mo alloy additive manufactured by electron beam meltingActa Mater., 86 (2015), pp. 305-318, 10.1016/j.actamat.2014.11.012 View PDF View article View in Scopus Google Scholar
[9]W. Xu, M. Brandt, S. Sun, J. Elambasseril, Q. Liu, K. Latham, K. Xia, M. QianAdditive manufacturing of strong and ductile Ti-6Al-4V by selective laser melting via in situ martensite decompositionActa Mater., 85 (2015), pp. 74-84, 10.1016/j.actamat.2014.11.028 View PDF View article View in Scopus Google Scholar
[10]S.S. Al-Bermani, M.L. Blackmore, W. Zhang, I. ToddThe origin of microstructural diversity, texture, and mechanical properties in electron beam melted Ti-6Al-4VMetall. Mater. Trans. A Phys. Metall. Mater. Sci., 41 (2010), pp. 3422-3434, 10.1007/s11661-010-0397-x View article View in Scopus Google Scholar
[11]P.L. Stephenson, N. Haghdadi, R. DeMott, X.Z. Liao, S.P. Ringer, S. PrimigEffect of scanning strategy on variant selection in additively manufactured Ti-6Al-4VAddit. Manuf., 36 (2020), Article 101581, 10.1016/j.addma.2020.101581 View PDF View article View in Scopus Google Scholar
[12]Y.K. Kim, K.A. LeeDirect energy deposition of high strength austenitic stainless steel matrix nanocomposite with superior ductility: microstructure, tensile properties, and deformation behaviorMater. Charact., 179 (2021), Article 111358, 10.1016/j.matchar.2021.111358 View PDF View article View in Scopus Google Scholar
[13]H. Helmer, A. Bauereiß, R.F. Singer, C. KörnerErratum to: ‘Grain structure evolution in Inconel 718 during selective electron beam melting’ (Materials Science & Engineering A (2016) 668 (180–187 (S0921509316305536) (10.1016/j.msea.2016.05.046))Mater. Sci. Eng. A., 676 (2016), p. 546, 10.1016/j.msea.2016.09.016 View PDF View article View in Scopus Google Scholar
[14]X. Wang, T. Keya, K. ChouBuild height effect on the Inconel 718 parts fabricated by selective laser meltingProcedia Manuf., 5 (2016), pp. 1006-1017, 10.1016/j.promfg.2016.08.089 View PDF View article View in Scopus Google Scholar
[15]P. Krakhmalev, I. Yadroitsava, G. Fredriksson, I. YadroitsevIn situ heat treatment in selective laser melted martensitic AISI 420 stainless steelsMater. Des., 87 (2015), pp. 380-385, 10.1016/j.matdes.2015.08.045 View PDF View article View in Scopus Google Scholar
[16]N. Haghdadi, E. Whitelock, B. Lim, H. Chen, X. Liao, S.S. Babu, S.P. Ringer, S. PrimigMultimodal γ′ precipitation in Inconel-738 Ni-based superalloy during electron-beam powder bed fusion additive manufacturingJ. Mater. Sci., 55 (2020), pp. 13342-13350, 10.1007/s10853-020-04915-w View article View in Scopus Google Scholar
[17]B. Lim, H. Chen, Z. Chen, N. Haghdadi, X. Liao, S. Primig, S.S. Babu, A. Breen, S.P. RingerMicrostructure–property gradients in Ni-based superalloy (Inconel 738) additively manufactured via electron beam powder bed fusionAddit. Manuf. (2021), Article 102121, 10.1016/j.addma.2021.102121 View PDF View article View in Scopus Google Scholar
[18]P. Karimi, E. Sadeghi, P. Åkerfeldt, J. Ålgårdh, J. AnderssonInfluence of successive thermal cycling on microstructure evolution of EBM-manufactured alloy 718 in track-by-track and layer-by-layer designMater. Des., 160 (2018), pp. 427-441, 10.1016/j.matdes.2018.09.038 View PDF View article View in Scopus Google Scholar
[19]E. Chauvet, P. Kontis, E.A. Jägle, B. Gault, D. Raabe, C. Tassin, J.J. Blandin, R. Dendievel, B. Vayre, S. Abed, G. MartinHot cracking mechanism affecting a non-weldable Ni-based superalloy produced by selective electron Beam MeltingActa Mater., 142 (2018), pp. 82-94, 10.1016/j.actamat.2017.09.047 View PDF View article View in Scopus Google Scholar
[20]M. Ramsperger, R.F. Singer, C. KörnerMicrostructure of the nickel-base superalloy CMSX-4 fabricated by selective electron beam meltingMetall. Mater. Trans. A Phys. Metall. Mater. Sci., 47 (2016), pp. 1469-1480, 10.1007/s11661-015-3300-y View PDF This article is free to access.View in Scopus Google Scholar
[21]B. Zhang, P. Wang, Y. Chew, Y. Wen, M. Zhang, P. Wang, G. Bi, J. WeiMechanical properties and microstructure evolution of selective laser melting Inconel 718 along building direction and sectional dimensionMater. Sci. Eng. A, 794 (2020), Article 139941, 10.1016/j.msea.2020.139941 View PDF View article View in Scopus Google Scholar
[22]C. Körner, M. Ramsperger, C. Meid, D. Bürger, P. Wollgramm, M. Bartsch, G. EggelerMicrostructure and mechanical properties of CMSX-4 single crystals prepared by additive manufacturingMetall. Mater. Trans. A Phys. Metall. Mater. Sci., 49 (2018), pp. 3781-3792, 10.1007/s11661-018-4762-5 View PDF This article is free to access.View in Scopus Google Scholar
[23]B. Lim, H. Chen, K. Nomoto, Z. Chen, A.I. Saville, S. Vogel, A.J. Clarke, A. Paradowska, M. Reid, S. Primig, X. Liao, S.S. Babu, A.J. Breen, S.P. RingerAdditively manufactured Haynes-282 monoliths containing thin wall struts of varying thicknessesAddit. Manuf., 59 (2022), Article 103120, 10.1016/j.addma.2022.103120 View PDF View article View in Scopus Google Scholar
[24]C.L.A. Leung, S. Marussi, R.C. Atwood, M. Towrie, P.J. Withers, P.D. LeeIn situ X-ray imaging of defect and molten pool dynamics in laser additive manufacturingNat. Commun., 9 (2018), pp. 1-9, 10.1038/s41467-018-03734-7 View PDF This article is free to access.View in Scopus Google Scholar
[25]C. Zhao, K. Fezzaa, R.W. Cunningham, H. Wen, F. De Carlo, L. Chen, A.D. Rollett, T. SunReal-time monitoring of laser powder bed fusion process using high-speed X-ray imaging and diffractionSci. Rep., 7 (2017), pp. 1-11, 10.1038/s41598-017-03761-2 View PDF This article is free to access.View in Scopus Google Scholar
[26]C. Kenel, D. Grolimund, X. Li, E. Panepucci, V.A. Samson, D.F. Sanchez, F. Marone, C. LeinenbachIn situ investigation of phase transformations in Ti-6Al-4V under additive manufacturing conditions combining laser melting and high-speed micro-X-ray diffractionSci. Rep., 7 (2017), pp. 1-10, 10.1038/s41598-017-16760-0 View PDF This article is free to access.Google Scholar
[27]W.L. Bevilaqua, J. Epp, H. Meyer, J. Dong, H. Roelofs, A. da, S. Rocha, A. RegulyRevealing the dynamic transformation of austenite to bainite during uniaxial warm compression through in-situ synchrotron X-ray diffractionMetals, 11 (2021), pp. 1-14, 10.3390/met11030467 View article View in Scopus Google Scholar
[28]B. Wahlmann, E. Krohmer, C. Breuning, N. Schell, P. Staron, E. Uhlmann, C. KörnerIn situ observation of γ′ phase transformation dynamics during selective laser melting of CMSX-4Adv. Eng. Mater., 23 (2021), 10.1002/adem.202100112 View PDF This article is free to access.Google Scholar
[29]M. Shiomi, A. Yoshidome, F. Abe, K. OsakadaFinite element analysis of melting and solidifying processes in laser rapid prototyping of metallic powdersInt. J. Mach. Tools Manuf., 39 (1999), pp. 237-252, 10.1016/S0890-6955(98)00036-4 View PDF View article View in Scopus Google Scholar
[30]A. Ilin, R. Logvinov, A. Kulikov, A. Prihodovsky, H. Xu, V. Ploshikhin, B. Günther, F. BechmannComputer aided optimisation of the thermal management during laser beam melting processPhys. Procedia, 56 (2014), pp. 390-399, 10.1016/J.PHPRO.2014.08.142 View PDF View article View in Scopus Google Scholar
[31]R. Acharya, J.A. Sharon, A. StaroselskyPrediction of microstructure in laser powder bed fusion processActa Mater., 124 (2017), pp. 360-371, 10.1016/J.ACTAMAT.2016.11.018 View PDF View article View in Scopus Google Scholar
[32]H.L. Wei, J.W. Elmer, T. DebroyOrigin of grain orientation during solidification of an aluminum alloyActa Mater., 115 (2016), pp. 123-131, 10.1016/J.ACTAMAT.2016.05.057 View PDF View article View in Scopus Google Scholar
[33]O. Zinovieva, A. Zinoviev, V. PloshikhinThree-dimensional modeling of the microstructure evolution during metal additive manufacturingComput. Mater. Sci., 141 (2018), pp. 207-220, 10.1016/J.COMMATSCI.2017.09.018 View PDF View article View in Scopus Google Scholar
[34]M.J. Anderson, C. Panwisawas, Y. Sovani, R.P. Turner, J.W. Brooks, H.C. BasoaltoMean-field modelling of the intermetallic precipitate phases during heat treatment and additive manufacture of Inconel 718Acta Mater., 156 (2018), pp. 432-445, 10.1016/J.ACTAMAT.2018.07.002 View PDF View article View in Scopus Google Scholar
[35]M.J. Anderson, J. Benson, J.W. Brooks, B. Saunders, H.C. BasoaltoPredicting precipitation kinetics during the annealing of additive manufactured Inconel 625 componentsIntegr. Mater. Manuf. Innov., 8 (2019), pp. 154-166, 10.1007/S40192-019-00134-7/FIGURES/11 View PDFThis article is free to access.View in Scopus Google Scholar
[36]H.C. Basoalto, C. Panwisawas, Y. Sovani, M.J. Anderson, R.P. Turner, B. Saunders, J.W. BrooksA computational study on the three-dimensional printability of precipitate-strengthened nickel-based superalloysProc. R. Soc. A, 474 (2018), 10.1098/RSPA.2018.0295 View article Google Scholar
[37]K. McNamara, Y. Ji, F. Lia, P. Promoppatum, S.C. Yao, H. Zhou, Y. Wang, L.Q. Chen, R.P. MartukanitzPredicting phase transformation kinetics during metal additive manufacturing using non-isothermal Johnson-Mehl-Avrami models: application to Inconel 718 and Ti-6Al-4VAddit. Manuf., 49 (2022), Article 102478, 10.1016/J.ADDMA.2021.102478 View PDF View article View in Scopus Google Scholar
[38]R. Radis, M. Schaffer, M. Albu, G. Kothleitner, P. Pölt, E. KozeschnikMultimodal size distributions of γ′ precipitates during continuous cooling of UDIMET 720 LiActa Mater., 57 (2009), pp. 5739-5747, 10.1016/j.actamat.2009.08.002 View PDF View article View in Scopus Google Scholar
[39]A. Drexler, B. Oberwinkler, S. Primig, C. Turk, E. Povoden-karadeniz, A. Heinemann, W. Ecker, M. StockingerMaterials Science & Engineering A Experimental and numerical investigations of the γ ″ and γ ′ precipitation kinetics in Alloy 718Mater. Sci. Eng. A., 723 (2018), pp. 314-323, 10.1016/j.msea.2018.03.013 View PDF View article View in Scopus Google Scholar
[40]M. Pudar, S. Zamberger, K. Spiradek-Hahn, R. Radis, E. KozeschnikComputational analysis of precipitation during continuous casting of microalloyed steelSteel Res. Int., 81 (2010), pp. 372-380, 10.1002/SRIN.201000021 View article View in Scopus Google Scholar
[41]M. Werinos, H. Antrekowitsch, E. Kozeschnik, T. Ebner, F. Moszner, J.F. Löffler, P.J. Uggowitzer, S. PogatscherUltrafast artificial aging of Al–Mg–Si alloysScr. Mater., 112 (2016), pp. 148-151, 10.1016/J.SCRIPTAMAT.2015.09.037 View PDF View article View in Scopus Google Scholar
[42]J. Svoboda, F.D. Fischer, P. Fratzl, E. KozeschnikModelling of kinetics in multi-component multi-phase systems with spherical precipitates I: theoryMater. Sci. Eng. A, 385 (2004), pp. 166-174, 10.1016/j.msea.2004.06.018 View PDF View article View in Scopus Google Scholar
[43]B. Stump, A. PlotkowskiAn adaptive integration scheme for heat conduction in additive manufacturingAppl. Math. Model., 75 (2019), pp. 787-805, 10.1016/j.apm.2019.07.008 View PDF View article View in Scopus Google Scholar
[44]A.V. Sotov, A.V. Agapovichev, V.G. Smelov, V.V. Kokareva, M.O. Dmitrieva, A.A. Melnikov, S.P. Golanov, Y.M. AnurovInvestigation of the IN-738 superalloy microstructure and mechanical properties for the manufacturing of gas turbine engine nozzle guide vane by selective laser meltingInt. J. Adv. Manuf. Technol., 107 (2020), pp. 2525-2535, 10.1007/s00170-020-05197-x View article View in Scopus Google Scholar
[45]F. Theska, A. Stanojevic, B. Oberwinkler, S.P. Ringer, S. PrimigOn conventional versus direct ageing of Alloy 718Acta Mater., 156 (2018), pp. 116-124, 10.1016/j.actamat.2018.06.034 View PDF View article View in Scopus Google Scholar
[46]T.M. Pollock, S. TinNickel-based superalloys for advanced turbine engines: chemistry, microstructure, and propertiesJ. Propuls. Power, 22 (2006), pp. 361-374, 10.2514/1.18239 View article View in Scopus Google Scholar
[47]O.A. Ojo, N.L. Richards, M.C. ChaturvediOn incipient melting during high temperature heat treatment of cast Inconel 738 superalloyJ. Mater. Sci., 39 (2004), pp. 7401-7404, 10.1023/B:JMSC.0000048761.32712.eb View article View in Scopus Google Scholar
[48]A.T. Egbewande, R.A. Buckson, O.A. OjoAnalysis of laser beam weldability of Inconel 738 superalloyMater. Charact., 61 (2010), pp. 569-574, 10.1016/j.matchar.2010.02.016 View PDF View article View in Scopus Google Scholar
[49]S. Sanchez, P. Smith, Z. Xu, G. Gaspard, C.J. Hyde, W.W. Wits, I.A. Ashcroft, H. Chen, A.T. ClarePowder Bed Fusion of nickel-based superalloys: a reviewInt. J. Mach. Tools Manuf., 165 (2021), 10.1016/j.ijmachtools.2021.103729 View PDF This article is free to access.Google Scholar
[50]C.L.A. Leung, R. Tosi, E. Muzangaza, S. Nonni, P.J. Withers, P.D. LeeEffect of preheating on the thermal, microstructural and mechanical properties of selective electron beam melted Ti-6Al-4V componentsMater. Des., 174 (2019), Article 107792, 10.1016/j.matdes.2019.107792 View PDF View article View in Scopus Google Scholar
[51]S. Griffiths, H. Ghasemi Tabasi, T. Ivas, X. Maeder, A. De Luca, K. Zweiacker, R. Wróbel, J. Jhabvala, R.E. Logé, C. LeinenbachCombining alloy and process modification for micro-crack mitigation in an additively manufactured Ni-base superalloyAddit. Manuf., 36 (2020), 10.1016/j.addma.2020.101443 View article Google Scholar
[52]P. Soille, L. Vincent Pierre Soille, L.M. Vincent, Determining watersheds in digital pictures via flooding simulations, Https://Doi.Org/10.1117/12.24211. 1360 (1990) 240–250. https://doi.org/10.1117/12.24211.Google Scholar
[53]ASTM Standard Test Method for Microindentation Hardness of MaterialsKnoop and Vickers Hardness of Materials 1, Annu. B ASTM Stand. i 2010 1 42.Google Scholar
[54]K.C. RussellNucleation in solids: the induction and steady state effectsAdv. Colloid Interface Sci., 13 (1980), pp. 205-318, 10.1016/0001-8686(80)80003-0 View PDF View article View in Scopus Google Scholar
[55]K. Janssens, D. Raabe, E. Kozeschnik, M. Miodownik, B. NestlerComputational Materials Engineering(first ed.), Elsevier (2007), 10.1016/B978-0-12-369468-3.X5000-X View article Google Scholar
[56]B. Sonderegger, E. KozeschnikGeneralized nearest-neighbor broken-bond analysis of randomly oriented coherent interfaces in multicomponent Fcc and Bcc structuresMetall. Mater. Trans. A Phys. Metall. Mater. Sci., 40 (2009), pp. 499-510, 10.1007/S11661-008-9752-6/FIGURES/8View article View in Scopus Google Scholar
[57]B. Sonderegger, E. KozeschnikSize dependence of the interfacial energy in the generalized nearest-neighbor broken-bond approachScr. Mater., 60 (2009), pp. 635-638, 10.1016/J.SCRIPTAMAT.2008.12.025 View PDF View article View in Scopus Google Scholar
[58]B. Sonderegger, E. KozeschnikInterfacial energy of diffuse phase boundaries in the generalized broken-bond approachMetall. Mater. Trans. A Phys. Metall. Mater. Sci., 41 (2010), pp. 3262-3269, 10.1007/S11661-010-0370-8/FIGURES/4View article View in Scopus Google Scholar
[59]E. Kozeschnik, J. Svoboda, F.D. FischerModified evolution equations for the precipitation kinetics of complex phases in multi-component systems28 (2005), pp. 379-382, 10.1016/j.calphad.2004.11.003 View article Google Scholar
[60]R. Kampmann, R. WagnerKInetics of precipitation in metastable binary alloys -theory and application to Cu-1.9 at% Ti AND Ni-14 at% AlDecompos. Alloy. Early Stages, Elsevier (1984), pp. 91-103, 10.1016/B978-0-08-031651-2.50018-5 View PDF View article View in Scopus Google Scholar
[61]E. Kozeschnik, J. Svoboda, P. Fratzl, F.D. FischerModelling of kinetics in multi-component multi-phase systems with spherical precipitates II: numerical solution and applicationMater. Sci. Eng. A, 385 (2004), pp. 157-165, 10.1016/j.msea.2004.06.016 View PDF View article View in Scopus Google Scholar
[62]J. Risse, Additive Manufacturing of Nickel-Base Superalloy IN738LC by Laser Powder Bed Fusion, (2019).Google Scholar
[63]F.L. Reyes Tirado, D.C. DunandIncreasing γ’ volume fraction in Co–Nb–V- and Co–Ta–V-based superalloysJ. Mater. Res. Technol., 11 (2021), pp. 2305-2313, 10.1016/J.JMRT.2021.02.028 View PDF View article View in Scopus Google Scholar
[64]E. KozeschnikModeling Solid-State PrecipitationMomentum Press (2012), 10.5643/9781606500644 View article Google Scholar
[65]B. Wahlmann, F. Galgon, A. Stark, S. Gayer, N. Schell, P. Staron, C. KörnerGrowth and coarsening kinetics of gamma prime precipitates in CMSX-4 under simulated additive manufacturing conditionsActa Mater., 180 (2019), pp. 84-96, 10.1016/j.actamat.2019.08.049 View PDF View article View in Scopus Google Scholar
[66]M. AvramiGranulation, phase change, and microstructure kinetics of phase change. IIIJ. Chem. Phys., 9 (1941), pp. 177-184, 10.1063/1.1750872 View article View in Scopus Google Scholar
[67]P. Strunz, M. Petrenec, J. Polák, U. Gasser, G. FarkasFormation and dissolution of’ precipitates in IN792 superalloy at elevated temperaturesMetals, 6 (2016), 10.3390/met6020037 View article Google Scholar
[68]A.R.P. Singh, S. Nag, J.Y. Hwang, G.B. Viswanathan, J. Tiley, R. Srinivasan, H.L. Fraser, R. BanerjeeInfluence of cooling rate on the development of multiple generations of γ′ precipitates in a commercial nickel base superalloyMater. Charact., 62 (2011), pp. 878-886, 10.1016/j.matchar.2011.06.002 View PDF View article View in Scopus Google Scholar
[69]E. Balikci, A. Raman, R. MirshamsMicrostructure evolution in polycrystalline IN738LC in the range 1120 to 1250C, Zeitschrift FuerMet, 90 (1999), pp. 132-140View in Scopus Google Scholar
[70]E. Balikci, D. ErdenizMultimodal precipitation in the superalloy IN738LCMetall. Mater. Trans. A Phys. Metall. Mater. Sci., 41 (2010), pp. 1391-1398, 10.1007/s11661-010-0241-3 View article View in Scopus Google Scholar
[71]Ł. Rakoczy, M. Grudzień-Rakoczy, F. Hanning, G. Cempura, R. Cygan, J. Andersson, A. Zielińska-LipiecInvestigation of the γ′ precipitates dissolution in a Ni-based superalloy during stress-free short-term annealing at high homologous temperaturesMetall. Mater. Trans. A Phys. Metall. Mater. Sci., 52 (2021), pp. 4767-4784, 10.1007/s11661-021-06420-4 View PDF This article is free to access.View in Scopus Google Scholar
[72]E. Balikci, A. RamanCharacteristics of the γ′ precipitates at high temperatures in Ni-base polycrystalline superalloy IN738LCJ. Mater. Sci., 35 (2000), pp. 3593-3597, 10.1023/A:1004869714854 View article View in Scopus Google Scholar
[73]F. Masoumi, D. Shahriari, M. Jahazi, J. Cormier, A. DevauxKinetics and Mechanisms of γ′ Reprecipitation in a Ni-based SuperalloySci. Rep., 6 (2016), pp. 1-16, 10.1038/srep28650 View article Google Scholar
[74]A.R.P. Singh, S. Nag, S. Chattopadhyay, Y. Ren, J. Tiley, G.B. Viswanathan, H.L. Fraser, R. BanerjeeMechanisms related to different generations of γ′ precipitation during continuous cooling of a nickel base superalloyActa Mater., 61 (2013), pp. 280-293, 10.1016/j.actamat.2012.09.058 View PDF View article View in Scopus Google Scholar
[75]O.M.D.M. Messé, R. Muñoz-Moreno, T. Illston, S. Baker, H.J. StoneMetastable carbides and their impact on recrystallisation in IN738LC processed by selective laser meltingAddit. Manuf., 22 (2018), pp. 394-404, 10.1016/j.addma.2018.05.030 View PDF View article View in Scopus Google Scholar
[76]N.D. Souza, M.C. Hardy, B. Roebuck, W.E.I. Li, G.D. West, D.M. Collins, On the Rate Dependence of Precipitate Formation and Dissolution in a Nickel-Base Superalloy, Metall. Mater. Trans. A. (n.d.). https://doi.org/10.1007/s11661–022-06680–8.Google Scholar
[77]M. Jahazi, A.R. MashreghiDissolution and precipitation kinetics of γ′ in nickel base superalloy Udimet 520Mater. Sci. Technol., 18 (2002), pp. 458-462, 10.1179/026708302225001606 View article View in Scopus Google Scholar
[78]H. Huang, G. Liu, H. Wang, A. Ullah, B. HuDissolution behavior and kinetics of γ′ phase during solution treatment in powder metallurgy nickel-based superalloyMetall. Mater. Trans. A., 51 (2020), pp. 1075-1084, 10.1007/s11661-019-05581-7 View article View in Scopus Google Scholar
[79]H. Huang, G. Liu, H. Wang, A. Ullah, B. HuDissolution behavior and kinetics of γ′ phase during solution treatment in powder metallurgy nickel-based superalloyMetall. Mater. Trans. A Phys. Metall. Mater. Sci., 51 (2020), pp. 1075-1084, 10.1007/s11661-019-05581-7 View article View in Scopus Google Scholar
[80]A.J. Goodfellow, E.I. Galindo-Nava, K.A. Christofidou, N.G. Jones, T. Martin, P.A.J. Bagot, C.D. Boyer, M.C. Hardy, H.J. StoneGamma prime precipitate evolution during aging of a model nickel-based superalloyMetall. Mater. Trans. A Phys. Metall. Mater. Sci., 49 (2018), pp. 718-728, 10.1007/s11661-017-4336-y View PDF This article is free to access.View in Scopus Google Scholar
[81]T.P. Gabb, D.G. Backman, D.Y. Wei, D.P. Mourer, D. Furrer, A. Garg, D.L. Ellis, #947;’ Form. a Nickel-Base Disk Superalloy 2012 405 414 doi: 10.7449/2000/superalloys_2000_405_414.Google Scholar
[82]A. PlatiModelling of γ precipitation in superalloys University of CambridgeMater. Sci. (2003), p. 73Google Scholar
[83]V.V. Rielli, F. Theska, F. Godor, A. Stanojevic, B. Oberwinkler, S. PrimigEvolution of nanoscale precipitates during common Alloy 718 ageing treatmentsMater. Des., 205 (2021), Article 109762, 10.1016/j.matdes.2021.109762 View PDF View article View in Scopus Google Scholar
[84]T. Grosdidier, A. Hazotte, A. SimonPrecipitation and dissolution processes in γ/γ′ single crystal nickel-based superalloysMater. Sci. Eng. A., 256 (1998), pp. 183-196, 10.1016/s0921-5093(98)00795-3 View PDF View article View in Scopus Google Scholar
[85]E. Balikci, A. Raman, R.A. MirshamsInfluence of various heat treatments on the microstructure of polycrystalline IN738LCMetall. Mater. Trans. A Phys. Metall. Mater. Sci., 28 (1997), pp. 1993-2003, 10.1007/s11661-997-0156-9 View article View in Scopus Google Scholar
[86]K. Thornton, N. Akaiwa, P.W. VoorheesLarge-scale simulations of Ostwald ripening in elastically stressed solids: I. Development of microstructureActa Mater., 52 (2004), pp. 1353-1364, 10.1016/j.actamat.2003.11.037 View PDF View article View in Scopus Google Scholar
[87]S. Tang, L.K. Ning, T.Z. Xin, Z. ZhengCoarsening behavior of gamma prime precipitates in a nickel based single crystal superalloyJ. Mater. Sci. Technol., 32 (2016), pp. 172-176, 10.1016/j.jmst.2015.10.005 View PDF View article View in Scopus Google Scholar
[88]S.S. Babu, M.K. Miller, J.M. Vitek, S.A. DavidCharacterization of the microstructure evolution in a nickel base superalloy during continuous cooling conditionsActa Mater., 49 (2001), pp. 4149-4160, 10.1016/S1359-6454(01)00314-7 View PDF View article View in Scopus Google Scholar
[89]M. Zhang, G.Q. Liu, H. Wang, B.F. HuStability of γ′ multimodal microstructure in a Ni-based powder metallurgy superalloySci. China Technol. Sci., 61 (2018), pp. 1824-1828, 10.1007/s11431-018-9372-8 View article View in Scopus Google Scholar
[90]P.M. Sarosi, B. Wang, J.P. Simmons, Y. Wang, M.J. MillsFormation of multimodal size distributions of γ′ in a nickel-base superalloy during interrupted continuous coolingScr. Mater., 57 (2007), pp. 767-770, 10.1016/j.scriptamat.2007.06.014 View PDF View article View in Scopus Google Scholar
[91]F. Theska, W.F. Tse, B. Schulz, R. Buerstmayr, S.R. Street, M. Lison-Pick, S. PrimigReview of microstructure–mechanical property relationships in cast and wrought ni-based superalloys with boron, carbon, and zirconium microalloying additionsAdv. Eng. Mater. (2022), p. 2201514, 10.1002/ADEM.202201514 View PDF This article is free to access.Google Scholar
[92]Y. Li, X. Liang, G. Peng, F. LinEffect of heat treatments on the microstructure and mechanical properties of IN738LC prepared by electron beam powder bed fusionJ. Alloy. Compd., 918 (2022), Article 165807, 10.1016/j.jallcom.2022.165807 View PDF View article View in Scopus Google Scholar
[93]L. Zhang, Y. Li, Q. Zhang, S. ZhangMicrostructure evolution, phase transformation and mechanical properties of IN738 superalloy fabricated by selective laser melting under different heat treatmentsMater. Sci. Eng. A, 844 (2022), Article 142947, 10.1016/j.msea.2022.142947 View PDF View article View in Scopus Google Scholar
[94]J.C. Franco-Correa, E. Martínez-Franco, J.M. Alvarado-Orozco, L.A. Cáceres-Díaz, D.G. Espinosa-Arbelaez, J.A. VilladaEffect of conventional heat treatments on the microstructure and microhardness of IN718 obtained by wrought and additive manufacturingJ. Mater. Eng. Perform., 30 (2021), pp. 7035-7045, 10.1007/s11665-021-06138-9 View article View in Scopus Google Scholar
[95]N. El-Bagoury, M. Waly, A. NofalEffect of various heat treatment conditions on microstructure of cast polycrystalline IN738LC alloyMater. Sci. Eng. A, 487 (2008), pp. 152-161, 10.1016/J.MSEA.2007.10.004 View PDF View article View in Scopus Google Scholar
[96]N. Li, M.J. Anderson, H.C. BasoaltoAutomated stereology and uncertainty quantification considering spherical non-penetrating dispersionsPage 464.Cryst 2023, Vol. 13 (13) (2023), p. 464, 10.3390/CRYST13030464 View article Google Scholar
[97]W.T. Loomis, J.W. Freeman, D.L. SponsellerInfluence of molybdenum on the γ′- phase in experimental nickelbase superalloysMet. Trans., 3 (1972), pp. 989-1000Google Scholar
[98]A.S. Shaikh Development of a γ’ Precipitation Hardening Ni-Base Superalloy for Additive Manufacturing Thesis 2018 102.〈https://odr.chalmers.se/handle/20.500.12380/255645%0Ahttps://www.researchgate.net/profile/Abdul_Shaafi_Shaikh2/publication/326226200%0Ahttps://drive.google.com/open?id=1BIez-aJyBTjnSgazzzTvv3jlrYpFC0N-〉.Google Scholar
[99]P. Caron High. γ′ Solvus N. Gener. Nickel-Based Superalloys Single Cryst. Turbine Bl. Appl. 5 2000 737 746 doi: 10.7449/2000/superalloys_2000_737_746.Google Scholar
[100]R. Rosenthal, D.R.F. WestContinuous γ′ precipitation in directionally solidified IN738 LC alloyMater. Sci. Technol., 15 (1999), pp. 1387-1394, 10.1179/026708399101505518 View article View in Scopus Google Scholar
[101]P. MichalerisModeling metal deposition in heat transfer analyses of additive manufacturing processesFinite Elem. Anal. Des., 86 (2014), pp. 51-60, 10.1016/J.FINEL.2014.04.003 View PDF View article View in Scopus Google Scholar
[102]P.N. Quested, R.F. Brooks, L. Chapman, R. Morrell, Y. Youssef, K.C. MillsMeasurement and estimation of thermophysical properties of nickel based superalloysMater. Sci. Technol., 25 (2009), pp. 154-162, 10.1179/174328408×361454View article View in Scopus Google Scholar
[103]D. Deng, J. Moverare, R.L. Peng, H. SöderbergMicrostructure and anisotropic mechanical properties of EBM manufactured Inconel 718 and effects of post heat treatmentsMater. Sci. Eng. A, 693 (2017), pp. 151-163, 10.1016/j.msea.2017.03.085 View PDF View article View in Scopus Google Scholar
[104]D. Deng, R.L. Peng, H. Söderberg, J. MoverareOn the formation of microstructural gradients in a nickel-base superalloy during electron beam meltingMater. Des., 160 (2018), pp. 251-261, 10.1016/j.matdes.2018.09.006 View PDF View article View in Scopus Google Scholar
[105]B.S. Bokstein, S.Z. Bokstein, I.T. SpitsbergNi self-diffusion in alloyed Ni3AlIntermetallics, 4 (1996), pp. 517-523, 10.1016/0966-9795(96)00038-6 View PDF View article View in Scopus Google Scholar
[106]J. Cermak, V. RothovaConcentration dependence of ternary interdiffusion coefficients in Ni3Al/Ni3Al-X couples with X = Cr, Fe, Nb and TiActa Mater., 51 (2003), pp. 4411-4421, 10.1016/S1359-6454(03)00276-3 View PDF View article View in Scopus Google Scholar
[107]M. Li, J. Coakley, D. Isheim, G. Tian, B. ShollockInfluence of the initial cooling rate from γ′ supersolvus temperatures on microstructure and phase compositions in a nickel superalloyJ. Alloy. Compd., 732 (2018), pp. 765-776, 10.1016/j.jallcom.2017.10.263 View PDF View article View in Scopus Google Scholar
[108]Y.Q. Chen, T.J.A. Slater, E.A. Lewis, E.M. Francis, M.G. Burke, M. Preuss, S.J. HaighMeasurement of size-dependent composition variations for gamma prime (γ’) precipitates in an advanced nickel-based superalloyUltramicroscopy, 144 (2014), pp. 1-8, 10.1016/j.ultramic.2014.04.001 View PDF View article Google Scholar
[109]Y.Q. Chen, E. Francis, J. Robson, M. Preuss, S.J. HaighCompositional variations for small-scale gamma prime (γ′) precipitates formed at different cooling rates in an advanced Ni-based superalloyActa Mater., 85 (2015), pp. 199-206, 10.1016/j.actamat.2014.11.009 View PDF View article View in Scopus Google Scholar

Study on the critical sediment concentration determining the optimal transport capability of submarine sediment flows with different particle size composition

Yupeng Ren ^abc, Huiguang Zhou ^cd, Houjie Wang ^ab, Xiao Wu ^ab, Guohui Xu ^cd, Qingsheng Meng ^cd

Abstract

해저 퇴적물 흐름은 퇴적물을 심해로 운반하는 주요 수단 중 하나이며, 종종 장거리를 이동하고 수십 또는 수백 킬로미터에 걸쳐 상당한 양의 퇴적물을 운반합니다. 그것의 강력한 파괴력은 종종 이동 과정에서 잠수함 유틸리티에 심각한 손상을 초래합니다.

퇴적물 흐름의 퇴적물 농도는 주변 해수와의 밀도차를 결정하며, 이 밀도 차이는 퇴적물 흐름의 흐름 능력을 결정하여 이송된 퇴적물의 최종 퇴적 위치에 영향을 미칩니다. 본 논문에서는 다양한 미사 및 점토 중량비(미사/점토 비율이라고 함)를 갖는 다양한 퇴적물 농도의 퇴적물 흐름을 수로 테스트를 통해 연구합니다.

우리의 테스트 결과는 특정 퇴적물 구성에 대해 퇴적물 흐름이 가장 빠르게 이동하는 임계 퇴적물 농도가 있음을 나타냅니다. 4가지 미사/점토 비율 각각에 대한 임계 퇴적물 농도와 이에 상응하는 최대 속도가 구해집니다. 결과는 점토 함량이 임계 퇴적물 농도와 선형적으로 음의 상관 관계가 있음을 나타냅니다.

퇴적물 농도가 증가함에 따라 퇴적물의 흐름 거동은 흐름 상태에서 붕괴된 상태로 변환되고 흐름 거동이 변화하는 두 탁한 현탁액의 유체 특성은 모두 Bingham 유체입니다.

또한 본 논문에서는 퇴적물 흐름 내 입자 배열을 분석하여 위에서 언급한 결과에 대한 미시적 설명도 제공합니다.

Submarine sediment flows is one of the main means for transporting sediment to the deep sea, often traveling long-distance and transporting significant volumes of sediment for tens or even hundreds of kilometers. Its strong destructive force often causes serious damage to submarine utilities on its course of movement. The sediment concentration of the sediment flow determines its density difference with the ambient seawater, and this density difference determines the flow ability of the sediment flow, and thus affects the final deposition locations of the transported sediment. In this paper, sediment flows of different sediment concentration with various silt and clay weight ratios (referred to as silt/clay ratio) are studied using flume tests. Our test results indicate that there is a critical sediment concentration at which sediment flows travel the fastest for a specific sediment composition. The critical sediment concentrations and their corresponding maximum velocities for each of the four silt/clay ratios are obtained. The results further indicate that the clay content is linearly negatively correlated with the critical sediment concentration. As the sediment concentration increases, the flow behaviors of sediment flows transform from the flow state to the collapsed state, and the fluid properties of the two turbid suspensions with changing flow behaviors are both Bingham fluids. Additionally, this paper also provides a microscopic explanation of the above-mentioned results by analyzing the arrangement of particles within the sediment flow.

Introduction

Submarine sediment flows are important carriers for sea floor sediment movement and may carry and transport significant volumes of sediment for tens or even hundreds of kilometers (Prior et al., 1987; Pirmez and Imran, 2003; Zhang et al., 2018). Earthquakes, storms, and floods may all trigger submarine sediment flow events (Hsu et al., 2008; Piper and Normark, 2009; Pope et al., 2017b; Gavey et al., 2017). Sediment flows have strong forces during the movement, which will cause great harm to submarine structures such as cables and pipelines (Pope et al., 2017a). It was first confirmed that the cable breaking event caused by the sediment flow occurred in 1929. The sediment flow triggered by the Grand Banks earthquake damaged 12 cables. According to the time sequence of the cable breaking, the maximum velocity of the sediment flow is as high as 28 m/s (Heezen and Ewing, 1952; Kuenen, 1952; Heezen et al., 1954). Subsequent research shows that the lowest turbidity velocity that can break the cable also needs to reach 19 m/s (Piper et al., 1988). Since then, there have been many damage events of submarine cables and oil and gas pipelines caused by sediment flows in the world (Hsu et al., 2008; Carter et al., 2012; Cattaneo et al., 2012; Carter et al., 2014). During its movement, the sediment flow will gradually deposit a large amount of sediment carried by it along the way, that is, the deposition process of the sediment flow. On the one hand, this process brings a large amount of terrestrial nutrients and other materials to the ocean, while on the other hand, it causes damage and burial to benthic organisms, thus forming the largest sedimentary accumulation on Earth – submarine fans, which are highly likely to become good reservoirs for oil and gas resources (Daly, 1936; Yuan et al., 2010; Wu et al., 2022). The study on sediment flows (such as, the study of flow velocity and the forces acting on seabed structures) can provide important references for the safe design of seabed structures, the protection of submarine ecosystems, and exploration of turbidity sediments related oil and gas deposits. Therefore, it is of great significance to study the movement of sediment flows.

The sediment flow, as a highly sediment-concentrated fluid flowing on the sea floor, has a dense bottom layer and a dilute turbulent cloud. Observations at the Monterey Canyon indicated that the sediment flow can maintain its movement over long distances if its bottom has a relatively high sediment concentration. This dense bottom layer can be very destructive along its movement path to any facilities on the sea floor (Paull et al., 2018; Heerema et al., 2020; Wang et al., 2020). The sediment flow mentioned in this research paper is the general term of sediment density flow.

The sediment flow, which occurs on the seafloor, has the potential to cause erosion along its path. In this process, the suspended sediment is replenished, allowing the sediment flow to maintain its continuous flow capacity (Zhao et al., 2018). The dynamic force of sediment flow movement stem from its own gravity and density difference with surrounding water. In cases that the gravity drive of the slope is absent (on a flat sea floor), the flow velocity and distance of sediment flows are essentially determined by the sediment composition and concentration of the sediment flows as previous studies have demonstrated. Ilstad et al. (2004) conducted underwater flow tests in a sloped tank and employed high speed video camera to perform particle tracking. The results indicated that the premixed sand-rich and clay-rich slurries demonstrated different flow velocity and flow behavior. Using mixed kaolinite(d50 = 6 μm) and silica flour(d50 = 9 μm) in three compositions with total volumetric concentration ranged 22% or 28%, Felix and Peakall (2006) carried out underwater flow tests in a 5° slope Perspex channel and found that the flow ability of sediment flows is different depending on sediment compositions and concentrations. Sumner et al. (2009) used annular flume experiments to investigate the depositional dynamics and deposits of waning sediment-laden flows, finding that decelerating fast flows with fixed sand content and variable mud content resulted in four different deposit types. Chowdhury and Testik (2011) used lock-exchange tank, and experimented the kaolin clay sediment flows in the concentration range of 25–350 g/L, and predicted the fluid mud sediment flows propagation characteristics, but this study focused on giving sediment flows propagate phase transition time parameters, and is limited to clay. Lv et al. (2017) found through experiments that the rheological properties and flow behavior of kaolin clay (d50 = 3.7 μm) sediment flows were correlated to clay concentrations. In the field monitoring conducted by Liu et al. (2023) at the Manila Trench in the South China Sea in 2021, significant differences in the velocity, movement distance, and flow morphology of turbidity currents were observed. These differences may be attributed to variations in the particle composition of the turbidity currents.

On low and gentle slopes, although sediment flow with sand as the main sediment composition moves faster, it is difficult to propagate over long distances because sand has greater settling velocity and subaqueous angle of repose. Whereas the sediment flows with silt and clay as main composition may maintain relatively stable currents. Although its movement speed is slow, it has the ability to propagate over long distances because of the low settling rate of the fine particles (Ilstad et al., 2004; Liu et al., 2023). In a field observation at the Gaoping submarine canyon, the sediments collected from the sediment flows exhibited grain size gradation and the sediment was mostly composed of silt and clay (Liu et al., 2012). At the largest deltas in the world, for instance, the Mississippi River Delta, the sediments are mainly composed of silt and clay, which generally distributed along the coast in a wide range and provided the sediment sources for further distribution. The sediment flows originated and transported sediment from the coast to the deep sea are therefore share the same sediment compositions as delta sediments. To study the sediment flows composed of silt and clay is of great importance.

The sediment concentration of the sediment flows determines the density difference between the sediment flows and the ambient water and plays a key role in its flow ability. For the sediment flow with sediment composed of silt and clay, low sediment concentration means low density and therefore leads to low flow ability; however, although high sediment concentration results in high density, since there is cohesion between fine particles, it changes fluid properties and leads to low flow ability as well. Therefore, there should be a critical sediment concentration with mixed composition of silt and clay, at which the sediment flow maintains its strongest flow capacity and have the highest movement speed. In other words, the two characteristics of particle diameter and concentration of the sediment flow determine its own motion ability, which, if occurs, may become the most destructive force to submarine structures.

The objectives of this work was to study how the sediment composition (measured in relative weight of silt and clay, and referred as silt/clay ratio) and sediment concentration affect flow ability and behavior of the sediment flows, and to quantify the critical sediment concentration at which the sediment flows reached the greatest flow velocity under the experiment setting. We used straight flume without slope and conducted a series of flume tests with varying sediment compositions (silt-rich or clay-rich) and concentrations (96 to 1212 g/L). Each sediment flow sample was tested and analyzed for rheological properties using a rheometer, in order to characterize the relationship between flow behavior and rheological properties. Combined with the particle diameter, density and viscosity characteristics of the sediment flows measured in the experiment, a numerical modeling study is conducted, which are mutually validated with the experimental results.

The sediment concentration determines the arrangements of the sediment particles in the turbid suspension, and the arrangement impacts the fluid properties of the turbid suspension. The microscopic mode of particle arrangement in the turbid suspension can be constructed to further analyze the relationship between the fluid properties of turbid suspension and the flow behaviors of the sediment flow, and then characterize the critical sediment concentration at which the sediment flow runs the fastest. A simplified microscopic model of particle arrangement in turbid suspension was constructed to analyze the microscopic arrangement characteristics of sediment particles in turbid suspension with the fastest velocity.

Section snippets

Equipment and materials

The sediment flows flow experiments were performed in a Perspex channel with smooth transparent walls. The layout and dimensions of the experimental set-up were shown in Fig. 1. The bottom of the channel was flat and straight, and a gate was arranged to separate the two tanks. In order to study the flow capacity of turbidity currents from the perspective of their own composition (particle size distribution and concentration), we used a straight channel instead of an inclined one, to avoid any

Relationship between sediment flow flow velocity and sediment concentration

After the sediment flow is generated, its movement in the first half (50 cm) of the channel is relatively stable, and there is obvious shock diffusion in the second half. The reason is that the excitation wave (similar to the surge) will be formed during the sediment flow movement, and its speed is much faster than the speed of the sediment flow head. When the excitation wave reaches the tail of the channel, it will be reflected, thus affecting the subsequent flow of the sediment flow.

Sediment flows motion simulation based on FLOW-3D

As a relatively mature 3D fluid simulation software, FLOW-3D can accurately predict the free surface flow, and has been used to simulate the movement process of sediment flows for many times (Heimsund, 2007). The model adopted in this paper is RNG turbulence model, which can better deal with the flow with high strain rate and is suitable for the simulation of sediment flows with variable shape during movement. The governing equations of the numerical model involved include continuity equation,

Conclusions

In this study, we conducted a series of sediment flow flume tests with mixed silt and clay sediment samples in four silt/clay ratios on a flat slope. Rheological measurements were carried out on turbid suspension samples and microstructure analysis of the sediment particle arrangements was conducted, we concluded that:

(1)The flow velocity of the sediment flow is controlled by the sediment concentration and its own particle diameter composition, the flow velocity increased with the increase of the

Declaration of Competing Interest

The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper.

Acknowledgements

This work was supported by the National Natural Science Foundation of China [Grant no. 42206055]; the National Natural Science Foundation of China [Grant no. 41976049]; and the National Natural Science Foundation of China [Grant no. 42272327].

References (39)

M.R. Chowdhury et al.Laboratory testing of mathematical models for high-concentration fluid mud turbidity currentsOcean Eng.(2011)
R. Gavey et al.Frequent sediment density flows during 2006 to 2015, triggered by competing seismic and weather events: Observations from subsea cable breaks off southern TaiwanMar. Geol.(2017)
B.C. Heezen et al.Further evidence for a turbidity current following the 1929 Grand Banks earthquakeDeep-Sea Res.(1954)
T. Ilstad et al.Subaqueous debris flow behaviour and its dependence on the sand/clay ratio: a laboratory study using particle trackingMar. Geol.(2004)
G. ParkerConditions for the ignition of catastrophically erosive turbidity currentsMar. Geol.(1982)
C. Pirmez et al.Reconstruction of turbidity currents in Amazon ChannelMar. Pet. Geol.(2003)
E.L. Pope et al.Which earthquakes trigger damaging submarine mass movements: Insights from a global record of submarine cable breaks?Mar. Geol.(2017)
E.L. Pope et al.Damaging sediment density flows triggered by tropical cyclonesEarth Planet. Sci. Lett.(2017)
Z. Wang et al.Direct evidence of a high-concentration basal layer in a submarine turbidity currentDeep Sea Res. Part(2020)
R.A. BagnoldAuto-suspension of transported sediment; turbidity currentsProc. R. Soc. Lond.(1962)
L. Carter et al.Near-synchronous and delayed initiation of long run-out submarine sediment flows from a record-breaking river flood, offshore TaiwanGeophys. Res. Lett.(2012)
L. Carter et al.Insights into submarine geohazards from breaks in subsea telecommunication cablesOceanography(2014)
A. Cattaneo et al.Searching for the seafloor signature of the 21 May 2003 Boumerdès earthquake offshore Central AlgeriaNat. Hazard. Earth. Sys.(2012)
S. ChoiLayer-averaged modeling of two-dimensional turbidity currents with a dissipative; galerkin finite element method; part i, formulation and application exampleJ. Hydraul. Res.(1998)
S.U. Choi et al.k-ε Turbulence modeling of density currents developing two dimensionally on a slopeJ. Hydraul. Eng.(2002)
R.A. DalyOrigin of submarine canyonsAm. J. Sci.(1936)
M. Felix et al.Transformation of debris flows into turbidity currents : mechanisms inferred from laboratory experimentsSedimentology(2006)
F.H. Harlow et al.Turbulence transport equationsPhys. Fluids(1967)
G.J. Heerema et al.What determines the downstream evolution of turbidity currents?Earth Planet. Sci. Lett.(2020)

There are more references available in the full text version of this article.

원본 보기

Figure 2-15: Système expérimental du plan incliné

새로운 콘크리트의 유체 흐름 모델링

Sous la direction de :
Marc Jolin, directeur de recherche
Benoit Bissonnette, codirecteur de recherche

Modélisation de l’écoulement du béton frais

Abstract

현재의 기후 비상 사태와 기후 변화에 관한 다양한 과학적 보고서를 고려할 때 인간이 만든 오염을 대폭 줄이는 것은 필수적이며 심지어 중요합니다. 최신 IPCC(기후변화에 관한 정부 간 패널) 보고서(2022)는 2030년까지 배출량을 절반으로 줄여야 함을 나타내며, 지구 보존을 위해 즉각적인 조치를 취해야 한다고 강력히 강조합니다.

이러한 의미에서 콘크리트 생산 산업은 전체 인간 이산화탄소 배출량의 4~8%를 담당하고 있으므로 환경에 미치는 영향을 줄이기 위한 진화가 시급히 필요합니다.

본 연구의 주요 목적은 이미 사용 가능한 기술적 품질 관리 도구를 사용하여 생산을 최적화하고 혼합 시간을 단축하며 콘크리트 폐기물을 줄이기 위한 신뢰할 수 있고 활용 가능한 수치 모델을 개발함으로써 이러한 산업 전환에 참여하는 것입니다.

실제로, 혼합 트럭 내부의 신선한 콘크리트의 거동과 흐름 프로파일을 더 잘 이해할 수 있는 수치 시뮬레이션을 개발하면 혼합 시간과 비용을 더욱 최적화할 수 있으므로 매우 유망합니다. 이러한 복잡한 수치 도구를 활용할 수 있으려면 수치 시뮬레이션을 검증, 특성화 및 보정하기 위해 기본 신 콘크리트 흐름 모델의 구현이 필수적입니다.

이 논문에서는 세 가지 단순 유동 모델의 개발이 논의되고 얻은 결과는 신선한 콘크리트 유동의 수치적 거동을 검증하는 데 사용됩니다. 이러한 각 모델은 강점과 약점을 갖고 있으며, 신선한 콘크리트의 유변학과 유동 거동을 훨씬 더 잘 이해할 수 있는 수치 작업 환경을 만드는 데 기여합니다.

따라서 이 연구 프로젝트는 새로운 콘크리트 생산의 완전한 모델링을 위한 진정한 관문입니다.

In view of the current climate emergency and the various scientific reports on climate change, it is essential and even vital to drastically reduce man-made pollution. The latest IPCC (Intergovernmental Panel on Climate Change) report (2022) indicates that emissions must be halved by 2030 and strongly emphasizes the need to act immediately to preserve the planet. In this sense, the concrete production industry is responsible for 4-8% of total human carbon dioxide emissions and therefore urgently needs to evolve to reduce its environmental impact. The main objective of this study is to participate in this industrial transition by developing a reliable and exploitable numerical model to optimize the production, reduce mixing time and also reduce concrete waste by using technological quality control tools already available. Indeed, developing a numerical simulation allowing to better understand the behavior and flow profiles of fresh concrete inside a mixing-truck is extremely promising as it allows for further optimization of mixing times and costs. In order to be able to exploit such a complex numerical tool, the implementation of elementary fresh concrete flow models is essential to validate, characterize and calibrate the numerical simulations. In this thesis, the development of three simple flow models is discussed and the results obtained are used to validate the numerical behavior of fresh concrete flow. Each of these models has strengths and weaknesses and contributes to the creation of a numerical working environment that provides a much better understanding of the rheology and flow behavior of fresh concrete. This research project is therefore a real gateway to a full modelling of fresh concrete production.

Key words

fresh concrete, rheology, numerical simulation, mixer-truck, rheological probe.

Figure 2-19: Essai d'affaissement au cône d'Abrams — Figure 2-19: Essai d’affaissement au cône d’Abrams

Reference

Amziane, S., Ferraris, C. F., & Koehler, E. (2006). Feasibility of Using a Concrete
Mixing Truck as a Rheometer.
Anderson, J. D. (1991). Fundamentals of aerodynamics. McGraw-Hill.
Balmforth, N. J., Craster, R. V., & Sassi, R. (2002). Shallow viscoplastic flow on an
inclined plane. Journal of Fluid Mechanics, 470, 1-29.
https://doi.org/10.1017/S0022112002001660
Banfill, P., Beaupré, D., Chapdelaine, F., de Larrard, F., Domone, P., Nachbaur, L.,
Sedran, T., Wallevik, O., & Wallevik, J. E. (2000). Comparison of concrete
rheometers International tests at LCPC (Nantes, France) in October 2000. In
NIST.
Baracu T. (2012). Computational analysis of the flow around a cylinder and of the
drag force.
Barreto, D., & Leak, J. (2020). A guide to modeling the geotechnical behavior of soils
using the discrete element method. In Modeling in Geotechnical Engineering (p.
79-100). Elsevier. https://doi.org/10.1016/B978-0-12-821205-9.00016-2
Baudez, J. C., Chabot, F., & Coussot, P. (2002). Rheological interpretation of the
slump test. Applied Rheology, 12(3), 133-141. https://doi.org/10.1515/arh-2002-
0008
Beaupre, D. (2012). Mixer-mounted probe measures concrete workability.
Berger, X. (2023). Proposition de recherche et préparation orale de doctorat (GCI8084).
Bergeron, P. (1953). Considérations sur les facteurs influençant l’usure due au
transport hydraulique de matériaux solides. Application plus particulière aux
machines. https://www.persee.fr/doc/jhydr_0000-0001_1953_act_2_1_3256
Bingham, E. (1922). Fluidity and Plasticity (Digitized by the Internet Archive in 2007).
http://www.archive.org/details/fluidityplasticiOObinguoft
Bruschi, G., Nishioka, T., Tsang, K., & Wang, R. (2003). A comparison of analytical
methods drag coefficient of a cylinder.

Caceres, E. C. (2019). Impact de la rhéologie des matériaux cimentaires sur l’aspect
des parements et les procédés de mise en place. https://tel.archivesouvertes.fr/tel-01982159
Chanson, H., Jarny, ; S, & Coussot, P. (2006). Dam Break Wave of Thixotropic Fluid.
https://doi.org/10.1061/ASCE0733-94292006132:3280
Chi, Z. P., Yang, H., Li, R., & Sun, Q. C. (2021). Measurements of unconfined fresh
concrete flow on a slope using spatial filtering velocimetry. Powder Technology,
393, 349-356. https://doi.org/10.1016/j.powtec.2021.07.088
Cochard, S., & Ancey, C. (2009). Experimental investigation of the spreading of
viscoplastic fluids on inclined planes. Journal of Non-Newtonian Fluid
Mechanics, 158(1-3), 73-84. https://doi.org/10.1016/j.jnnfm.2008.08.007
Coussot, Philippe., & Ancey, C. (Christophe). (1999). Rhéophysique des pâtes et
des suspensions. EDP Sciences.
CSA Group. (2019). CSA A23.1:19 / CSA A23.2:19 : Concrete materials and
methods of concret construction / Test methods and standard practices for
concrete.
Daczko, J. A. (2000). A proposal for measuring rheology of production concrete.
De Larrard, F. (1999). Structures granulaires et formulation des bétons.
http://www.lcpc.fr/betonlabpro
De Larrard, F., Ferraris, C. F., & Sedran, T. (1998). Fresh concrete: A HerscheIBulkley material (Vol. 31).
Domone P.L.J., J. J. (1999). Properties of mortar for self-compacting concrete.
RILEM, 109-120.
El-Reedy, M. (2009). Advanced Materials and Techniques for Reinforced Concrete
Structures.
Emborg M. (1999). Rheology tests for self-compacting concrete – how useful are
they for the design of concrete mix for full-scale production.
Fall A. (2008). Rhéophysique des fluides complexes : Ecoulement et Blocage de
suspensions concentrées. https://www.researchgate.net/publication/30515545
Ferraris, C. F., Brower, L. E., Beaupré, D., Chapdelaine, F., Domone, P., Koehler,
E., Shen, L., Sonebi, M., Struble, L., Tepke, D., Wallevik, O., & Wallevik, J. E.

(2003). Comparison of concrete rheometers: International tests at MB.
https://doi.org/10.6028/NIST.IR.7154
Ferraris, C. F., & de Larrard, F. (1998a). Rhéologie du béton frais remanié III – L’essai
au cône d’Abrams modifié.
Ferraris, C. F., & de Larrard, F. (1998b, février). NISTIR 6094 Testing and modelling
of fresh concrete rheology. NISTIR 6094.
https://ciks.cbt.nist.gov/~garbocz/rheologyNISTIR/FR97html.htm
Fischedick, M., Roy, J., Abdel-Aziz, A., Acquaye Ghana, A., Allwood, J., Baiocchi,
G., Clift, R., Nenov, V., Yetano Roche Spain, M., Roy, J., Abdel-Aziz, A.,
Acquaye, A., Allwood, J. M., Ceron, J., Geng, Y., Kheshgi, H., Lanza, A.,
Perczyk, D., Price, L., … Minx, J. (2014). Climate Change 2014.
Fox R., & McDonald A. (2004). Introduction to fluid mechanics.
Franco Correa I.-D. (2019). Étude tribologique à hautes températures de matériaux
céramiques structurés à différentes échelles.
GIEC. (2022). Climate Change 2022 : Mitigation of Climate Change. www.ipcc.ch
Gouvernement du Canada. (2021, mai 31). Déclaration commune : L’industrie
canadienne du ciment et le gouvernement du Canada annoncent un partenariat.
https://www.ic.gc.ca/eic/site/icgc.nsf/fra/07730.html
Grenier, M. (1998). Microstructure et résistance à l’usure de revêtements crées par
fusion laser avec gaz réactifs sur du titane.
Herschel, W. H., & Bulkley, R. (1926). Konsistenzmessungen von GummiBenzollösungen. Kolloid-Zeitschrift, 39(4), 291-300.
https://doi.org/10.1007/BF01432034
Hirt, C. W., & Nichols, B. D. (1981). Volume of fluid (VOF) method for the dynamics
of free boundaries. Journal of Computational Physics, 39(1), 201-225.
https://doi.org/https://doi.org/10.1016/0021-9991(81)90145-5
Hoornahad, H., & Koenders, E. A. B. (2012). Simulation of the slump test based on
the discrete element method (DEM). Advanced Materials Research, 446-449,
3766-3773. https://doi.org/10.4028/www.scientific.net/AMR.446-449.3766

Hu, C., de Larrard, F., Sedran, T., Boulay, C., Bosd, F., & Deflorenne, F. (1996).
Validation of BTRHEOM, the new rheometer for soft-to-fluid concrete. In
Materials and Structures/Mat~riaux et Constructions (Vol. 29).
Jeong, S. W., Locat, J., Leroueil, S., & Malet, J. P. (2007). Rheological properties of
fine-grained sediments in modeling submarine mass movements: The role of
texture. Submarine Mass Movements and Their Consequences, 3rd
International Symposium, 191-198. https://doi.org/10.1007/978-1-4020-6512-
5_20
Kabagire, K. D. (2018). Modélisation expérimentale et analytique des propriétés
rhéologiques des bétons autoplaçants.
Katopodes, N. D. (2019). Volume of Fluid Method. In Free-Surface Flow (p.
766-802). Elsevier. https://doi.org/10.1016/b978-0-12-815485-4.00018-8
Khayat. (2008). Personnal Communication.
Kosmatka, S. (2011). Dosage et contrôle des mélanges de béton (8ème édition).
Li, H., Wu, A., & Cheng, H. (2022). Generalized models of slump and spread in
combination for higher precision in yield stress determination. Cement and
Concrete Research, 159. https://doi.org/10.1016/j.cemconres.2022.106863
Massey, B., & Smith, J. (2012). Mechanics of fluids 9ème édition.
Mokéddem, S. (2014). Contrôle de la rhéologie d’un béton et de son évolution lors
du malaxage par des mesures en ligne à l’aide de la sonde Viscoprobe.
https://tel.archives-ouvertes.fr/tel-00993153
Munson, B. R., & Young, D. R. (2006). Fundamental of Fluid Mechanics (5th éd.).
Munson, M., Young, M. , & Okiishi, M. (2020). Mécanique des fluides (8ème édition).
Murata, J., & Kikukawa, H. (1992). Viscosity Equation for Fresh Concrete.
Nakayama, Y., & Boucher, R. F. (2000). Introduction to fluid mechanics. ButterworthHeinemann.
Němeček, J. (2021). Numerical simulation of slump flow test of cement paste
composites. Acta Polytechnica CTU Proceedings, 30, 58-62.
https://doi.org/10.14311/APP.2021.30.0058
Nikitin, K. D., Olshanskii, M. A., Terekhov, K. M., & Vassilevski, Y. V. (2011). A
numerical method for the simulation of free surface flows of viscoplastic fluid in

3D. Journal of Computational Mathematics, 29(6), 605-622.
https://doi.org/10.4208/jcm.1109-m11si01
Noh, W. F., & Woodward, P. (1976). SLIC (Simple Line Interface Calculation).
Odabas, D. (2018). Effects of Load and Speed on Wear Rate of Abrasive Wear for
2014 Al Alloy. IOP Conference Series: Materials Science and Engineering,
295(1). https://doi.org/10.1088/1757-899X/295/1/012008
Pintaude, G. (s. d.). Characteristics of Abrasive Particles and Their Implications on
Wear. www.intechopen.com
Poullain, P. (2003). Étude comparative de l’écoulement d’un fluide viscoplastique
dans une maquette de malaxeur pour béton.
R. J. Cattolica. (2003). Experiment F2: Water Tunnel. In MAE171A/175A Mechanical
Engineering Laboratory Manual (Winter Quarter).
Raper, R. M. (1966). Drag force and pressure distribution on cylindrical
protuberances immersed in a turbulent channel flow.
RMCAO. (2013). CSA A23.2-5C: Concrete Basics Slump Test.
Roques, A., & School, H. (2006). High resolution seismic imaging applied to the
geometrical characterization of very high voltage electric pylons.
https://www.researchgate.net/publication/281566156
Roussel, N. (2006). Correlation between yield stress and slump: Comparison
between numerical simulations and concrete rheometers results. Materials and
Structures/Materiaux et Constructions, 39(4), 501-509.
https://doi.org/10.1617/s11527-005-9035-2
Roussel, N., & Coussot, P. (2005). “Fifty-cent rheometer” for yield stress
measurements: From slump to spreading flow. Journal of Rheology, 49(3),
705-718. https://doi.org/10.1122/1.1879041
Roussel, N., Geiker, M. R., Dufour, F., Thrane, L. N., & Szabo, P. (2007).
Computational modeling of concrete flow: General overview. Cement and
Concrete Research, 37(9), 1298-1307.
https://doi.org/10.1016/j.cemconres.2007.06.007
Schaer, N. (2019). Modélisation des écoulements à surface libre de fluides nonnewtoniens. https://theses.hal.science/tel-02166968

Schowalter, W. R., & Christensen, G. (1998). Toward a rationalization of the slump
test for fresh concrete: Comparisons of calculations and experiments. Journal
of Rheology, 42(4), 865-870. https://doi.org/10.1122/1.550905
Sofiane Amziane, Chiara F. Ferraris, & Eric P. Koehler. (2005). Measurement of
Workability of Fresh Concrete Using a Mixing Truck. Journal of Research of the
National Institute of Standards Technology, 55-56.
Sooraj, P., Agrawal, A., & Sharma, A. (2018). Measurement of Drag Coefficient for
an Elliptical Cylinder. Journal of Energy and Environmental Sustainability, 5,
1-7. https://doi.org/10.47469/jees.2018.v05.100050
Stachowiak G. (2006). Wear – Materials, Mechanisms and Pratice.
Stachowiak G.W. (1993). Tribology Series (Vol. 24, p. 557-612). Elsevier.
Tattersall, G., & Banfill, P. F. G. (1983). The rheology of fresh concrete.
The European Guidelines for Self-Compacting Concrete Specification, Production
and Use « The European Guidelines for Self Compacting Concrete ». (2005).
www.efnarc.org
University College London. (2010). Pressure around a cylinder and cylinder drag.
Van Oudheusden, B. W., Scarano, F., Roosenboom, E. W. M., Casimiri, E. W. F., &
Souverein, L. J. (2007). Evaluation of integral forces and pressure fields from
planar velocimetry data for incompressible and compressible flows.
Experiments in Fluids, 43(2-3), 153-162. https://doi.org/10.1007/s00348-007-
0261-y
Vasilic, K., Gram, A., & Wallevik, J. E. (2019). Numerical simulation of fresh concrete
flow: Insight and challenges. RILEM Technical Letters, 4, 57-66.
https://doi.org/10.21809/rilemtechlett.2019.92
Viccione, G., Ferlisi, S., & Marra, E. (2010). A numerical investigation of the
interaction between debris flows and defense barriers.
http://www.unisa.it/docenti/giacomoviccione/en/index
Wallevik J. (2006). Relation between the Bingham parameters and slump.
Wallevik, J. E. (2006). Relationship between the Bingham parameters and slump.
Cement and Concrete Research, 36(7), 1214-1221.
https://doi.org/10.1016/j.cemconres.2006.03.001

Wallevik, J. E., & Wallevik, O. H. (2020). Concrete mixing truck as a rheometer.
Cement and Concrete Research, 127.
https://doi.org/10.1016/j.cemconres.2019.105930

PDF 다운로드

Figure 1. US bath modified as an EC reactor

물에서 초음파를 이용한 전기화학적 스트론튬 제거에 대한 단시간 수치 시뮬레이션

전기화학 반응기에 대한 3D 수치 시뮬레이션 및 측정을 사용하여 동시 초음파 처리 유무에 관계없이 물에서 스트론튬 제거 효율을 분석했습니다. 초음파는 작동 주파수가 25kHz인 4개의 초음파 변환기를 사용하여 생성되었습니다. 반응기는 2개의 블록으로 배열된 8개의 알루미늄 전극을 사용했습니다.

LICHT K.¹*, LONČAR G.¹, POSAVČIĆ H.¹, HALKIJEVIĆ I.¹
1 Department of Hydroscience and Engineering, Faculty of Civil Engineering, University of Zagreb, Andrije Kačića-Miošića 26, 10000 Zagreb, Croatia
*corresponding author:
e-mail:katarina.licht@grad.unizg.hr

물 속의 스트론튬 이온은 3.2∙10-19C의 전하와 1.2∙10-8m의 직경을 특징으로 하는 입자로 모델링됩니다. 수치 모델은 기본 유체 역학 모듈, 정전기 모듈 및 일반 이동 객체 모듈을 사용하여 Flow-3D 소프트웨어에서 생성되었습니다.

수치 시뮬레이션을 통해 연구된 원자로 변형의 성능은 시뮬레이션 기간이 끝날 때 전극에 영구적으로 유지되는 모델 스트론튬 입자 수와 물 속의 초기 입자 수의 비율로 정의됩니다. 실험실 반응기의 경우 스트론튬 제거 효과는 실험 종료 시와 시작 시 물 내 균일한 스트론튬 농도의 비율로 정의됩니다.

결과는 초음파를 사용하면 수처리 180초 후에 스트론튬 제거 효과가 10.3%에서 11.2%로 증가한다는 것을 보여줍니다. 수치 시뮬레이션 결과는 동일한 기하학적 특성을 갖는 원자로에 대한 측정 결과와 일치합니다.

3D numerical simulations and measurements on an electrochemical reactor were used to analyze the efficiency of strontium removal from water, with and without simultaneous ultrasound treatment. Ultrasound was generated using 4 ultrasonic transducers with an operating frequency of 25 kHz. The reactor used 8 aluminum electrodes arranged in two blocks. Strontium ions in water are modeled as particles characterized by a charge of 3.2∙10-19 C and a diameter of 1.2∙10-8 m. The numerical model was created in Flow-3D software using the basic hydrodynamic module, electrostatic module, and general moving objects module. The performance of the studied reactor variants by numerical simulations is defined by the ratio of the number of model strontium particles permanently retained on the electrodes at the end of the simulation period to the initial number of particles in the water. For the laboratory reactor, the effect of strontium removal is defined by the ratio of the homogeneous strontium concentration in the water at the end and at the beginning of the experiments. The results show that the use of ultrasound increases the effect of strontium removal from 10.3% to 11.2% after 180 seconds of water treatment. The results of numerical simulations agree with the results of measurements on a reactor with the same geometrical characteristics.

Keywords

numerical model, electrochemical reactor, strontium

Figure 2. Schematic view of the experimental set-up

References

Dong, B., Fishgold, A., Lee, P., Runge, K., Deymier, P. and Keswani, M. (2016), Sono-electrochemical recovery of metal ions from their aqueous solutions, Journal of Hazardous Materials, 318, 379–387.
https://doi.org/10.1016/J.JHAZMAT.2016.07.007
EPA. (2014), Announcement of Final Regulatory Determinations for Contaminants on the Third Drinking
Water Contaminant Candidate List. Retrieved from http://fdsys.gpo.gov/fdsys/search/home.action
Fu, F., Lu, J., Cheng, Z. and Tang, B. (2016), Removal of selenite by zero-valent iron combined with ultrasound: Se(IV) concentration changes, Se(VI) generation, and reaction mechanism, Ultrasonics Sonochemistry, 29, 328–336. https://doi.org/10.1016/j.ultsonch.2015.10.007
Ince, N.H. (2018), Ultrasound-assisted advanced oxidation processes for water decontamination, Ultrasonics Sonochemistry, 40, 97–103.
https://doi.org/10.1016/j.ultsonch.2017.04.009
Kamaraj, R. and Vasudevan, S. (2015), Evaluation of electrocoagulation process for the removal of strontium and cesium from aqueous solution, Chemical
Engineering Research and Design, 93, 522–530.
https://doi.org/10.1016/j.cherd.2014.03.021
Luczaj, J. and Masarik, K. (2015), Groundwater Quantity and Quality Issues in a Water-Rich Region: Examples from Wisconsin, USA, Resources, 4(2), 323–357.
https://doi.org/10.3390/resources4020323
Mohapatra, D.P. and Kirpalani, D.M. (2019), Selenium in wastewater: fast analysis method development and advanced oxidation treatment applications, Water Science and Technology: A Journal of the International Association on Water Pollution Research, 79(5), 842–849. https://doi.org/10.2166/wst.2019.010

Mollah, M.Y.A., Schennach, R., Parga, J.R. and Cocke, D.L.(2001), Electrocoagulation (EC)- Science and
applications, Journal of Hazardous Materials, 84(1), 29–41. https://doi.org/10.1016/S0304-3894(01)00176-5

Moradi, M., Vasseghian, Y., Arabzade, H. and Khaneghah, A.M. (2021), Various wastewaters treatment by sonoelectrocoagulation process: A comprehensive review of operational parameters and future outlook, Chemosphere, 263, 128314. https://doi.org/10.1016/J.CHEMOSPHERE.2020.12831 4
Peng, H., Yao, F., Xiong, S., Wu, Z., Niu, G. and Lu, T. (2021), Strontium in public drinking water and associated public health risks in Chinese cities, Environmental Science and Pollution Research International, 28(18), 23048. https://doi.org/10.1007/S11356-021-12378-Y
Scott, V., Juran, L., Ling, E.J., Benham, B. and Spiller, A. (2020), Assessing strontium and vulnerability to strontium in private drinking water systems in Virginia, Water, 12(4). https://doi.org/10.3390/w12041053
Ziylan, A., Koltypin, Y., Gedanken, A. and Ince, N.H. (2013), More on sonolytic and sonocatalytic decomposition of Diclofenac using zero-valent iron, Ultrasonics Sonochemistry, 20(1), 580–586. https://doi.org/10.1016/j.ultsonch.2012.05.00

원본 PDF

원본 다운로드

Figure 1. Three-dimensional finite element model of local scouring of semi-exposed submarine cable.

반노출 해저케이블의 국부 정련과정 및 영향인자에 대한 수치적 연구

Numerical Study of the Local Scouring Process and Influencing Factors of Semi-Exposed Submarine Cables

by Qishun Li,Yanpeng Hao^*,Peng Zhang,Haotian Tan,Wanxing Tian,Linhao Chen andLin Yang

School of Electric Power Engineering, South China University of Technology, Guangzhou 510640, China

^*Author to whom correspondence should be addressed.J. Mar. Sci. Eng.2023, 11(7), 1349; https://doi.org/10.3390/jmse11071349

Received: 10 June 2023 / Revised: 19 June 2023 / Accepted: 27 June 2023 / Published: 1 July 2023(This article belongs to the Section Ocean Engineering)

일부 수식이 손상되어 표시될 수 있습니다. 이 경우 원문을 참조하시기 바랍니다.

Abstract

Local scouring might result in the spanning of submarine cables, endangering their mechanical and electrical properties. In this contribution, a three-dimensional computational fluid dynamics simulation model is developed using FLOW-3D, and the scouring process of semi-exposed submarine cables is investigated. The effects of the sediment critical Shields number, sediment density, and ocean current velocity on local scouring are discussed, and variation rules for the submarine cables’ spanning time are provided. The results indicate that three scouring holes are formed around the submarine cables. The location of the bottom of the holes corresponds to that of the maximum shear velocity. The continuous development of scouring holes at the wake position leads to the spanning of the submarine cables. The increase in the sediment’s critical Shields number and sediment density, as well as the decrease in the ocean current velocity, will extend the time for maintaining the stability of the upstream scouring hole and retard the development velocity of the wake position and downstream scouring holes. The spanning time has a cubic relationship with the sediment’s critical Shields number, a linear relationship with the sediment density, and an exponential relationship with the ocean current velocity. In this paper, the local scouring process of semi-exposed submarine cables is studied, which provides a theoretical basis for the operation and maintenance of submarine cables.

Keywords:

submarine cable; local scouring; numerical simulation; computational fluid dynamics

1. Introduction

As a key piece of equipment in cross-sea power grids, submarine cables are widely used to connect autonomous power grids, supply power to islands or offshore platforms, and transmit electric power generated by marine renewable energy installations to onshore substations [1]. Once submarine cables break down due to natural disasters or human-made damage, the normal operation of other marine electric power equipment connected to them may be affected. These chain reactions will cause great economic losses and serious social impacts [2].

To protect submarine cables, they are usually buried 1 to 3 m below the seabed [3]. However, submarine cables are still confronted with potential threats from the complex subsea environment. Under the influence of fishing, anchor damage, ocean current scouring, and other factors, the sediment above submarine cables will always inevitably migrate. When a submarine cable is partially exposed, the scouring at this position will be exacerbated; eventually, it will cause the submarine cable to span. According to a field investigation of the 500 kV oil-filled submarine cable that is part of the Hainan networking system, the total length of the span is 49 m [4]. Under strong ocean currents, spanning submarine cables may experience vortex-induced vibrations. Fatigue stress caused by vortex-induced vibrations may lead to metal sheath rupture [5], which endangers the mechanical and electrical properties of submarine cables. Therefore, understanding the local scouring processes of partially exposed submarine cables is crucial for predicting scouring patterns. This is the basis for developing effective operation and maintenance strategies for submarine cables.

The mechanism and influencing factors of sediment erosion have been examined by researchers around the world. In 1988, Sumer [6] conducted experiments to show that the shedding vortex in the wake of a pipeline would increase the Shields parameter by 3–4 times, which would result in severe scouring. In 1991, Chiew [7] performed experiments to prove that the maximum scouring depth could be obtained when the pipeline was located on a flat bed and was scoured by a unidirectional water flow. Based on the test results, they provided a prediction formula for the maximum scouring depth. In 2003, Mastbergen [8] proposed a one-dimensional, steady-state numerical model of turbidity currents, which considered the negative pore pressures in the seabed. The calculated results of this model were basically consistent with the actual scouring of a submarine canyon. In 2007, Dey [9] presented a semitheoretical model for the computation of the maximum clear-water scour depth below underwater pipelines in uniform sediments under a steady flow, and the predicted scour depth in clear water satisfactorily agreed with the observed values. In 2008, Dey [10] conducted experiments on clear-water scour below underwater pipelines under a steady flow and obtained a variation pattern of the depth of the scouring hole. In 2008, Liang [11] used a two-dimensional numerical simulation to study the scouring process of a tube bundle under the action of currents and waves. They discovered that, compared with the scouring of a single tube, the scouring depth of the tube bundle was deeper, and the scouring time was longer. In 2012, Yang [12] found that placing rubber sheets under pipes can greatly accelerate their self-burial. The rubber sheets had the best performance when their length was about 1.5 times the size of the pipe. In 2020, Li [13] investigated the two-dimensional local scour beneath two submarine pipelines in tandem under wave-plus-current conditions via numerical simulation. They found that for conditions involving waves plus a low-strength current, the scour pattern beneath the two pipelines behaved like that in the pure-wave condition. Conversely, when the current had equal strength to the wave-induced flow, the scour pattern beneath the two pipelines resembled that in the pure-current condition. In 2020, Guan [14] studied and discussed the interactive coupling effects among a vibrating pipeline, flow field, and scour process through experiments, and the experimental data showed that the evolution of the scour hole had significant influences on the pipeline vibrations. In 2021, Liu [15] developed a two-dimensional finite element numerical model and researched the local scour around a vibrating pipeline. The numerical results showed that the maximum vibration amplitude of the pipeline could reach about 1.2 times diameter, and the maximum scour depth occurred on the wake side of the vibrating pipeline. In 2021, Huang [16] carried out two-dimensional numerical simulations to investigate the scour beneath a single pipeline and piggyback pipelines subjected to an oscillatory flow condition at a KC number of 11 and captured typical steady-streaming structures around the pipelines due to the oscillatory flow condition. In 2021, Cui [17] investigated the characteristics of the riverbed scour profile for a pipeline buried at different depths under the condition of riverbed sediments with different particle sizes. The results indicated that, in general, the equilibrium scour depth changed in a spoon shape with the gradual increase in the embedment ratio. In 2022, Li [18] used numerical simulation to study the influence of the burial depth of partially buried pipelines on the surrounding flow field, but they did not investigate the scour depth. In 2022, Zhu [19] performed experiments to prove that the scour hole propagation rate under a pipeline decreases with an increasing pipeline embedment ratio and rises with the KC number. In 2022, Najafzadeh [20] proposed equations for the prediction of the scouring propagation rate around pipelines due to currents based on a machine learning model, and the prediction results were consistent with the experimental data. In 2023, Ma [21] used the computational fluid dynamics coarse-grained discrete element method to simulate the scour process around a pipeline. The results showed that this method can effectively reduce the considerable need for computing resources and excessive computation time. In 2023, through numerical simulations, Hu [22] discovered that the water velocity and the pipeline diameter had a significant effect on the depth of scouring.

In the preceding works, the researchers investigated the mechanism of sediment scouring and the effect of various factors on the local scouring of submarine pipelines. However, submarine cables are buried beneath the seabed, while submarine pipelines are erected above the seabed. The difference in laying methods leads to a large discrepancy between their local scouring processes. Therefore, the conclusions of the above investigations are not applicable to the local scouring of submarine cables. Currently, there is no report on the research of the local scouring of partially exposed submarine cables.

In this paper, a three-dimensional computational fluid dynamics (CFD) finite element model, based on two-phase flow, is established using FLOW-3D. The local scouring process of semi-exposed submarine cables under steady-state ocean currents is studied, and the variation rules of the depth and the shape of the scouring holes, as well as the shear velocity with time, are obtained. By setting different critical Shields numbers of the sediment, different sediment densities, and different ocean current velocities, the change rule of the scouring holes’ development rate and the time required for the spanning of submarine cables are explored.

2. Sediment Scouring Model

In the sediment scouring model, the sediment is set as the dispersed particle, which is regarded as a kind of quasifluid. In this context, sediment scouring is considered as a two-phase flow process between the liquid phase and solid particle phase. The sediment in this process is further divided into two categories: one is suspended in the fluid, and the other is deposited on the bottom.When the local Shields number of sediment is greater than the critical Shields number, the deposited sediment will be transformed into the suspended sediment under the action of ocean currents. The calculation formulae of the local Shields numbers θ and the critical Shields numbers

θ_cr of sediment is given as [23,24

]

𝜃=𝑈2𝑓(𝜌𝑠/𝜌𝑓−1)𝑔𝑑50,�=��2(��/��−1)��50,(1)

𝜃𝑐𝑟=0.31+1.2𝐷∗+0.055(1−𝑒−0.02𝐷∗),��=0.31+1.2�*+0.055(1−�−0.02�*),(2)

𝐷∗=𝑑50𝜌𝑓(𝜌𝑠−𝜌𝑓)𝑔/𝜇2−−−−−−−−−−−−−−√3,�*=�50��(��−��)�/�23,(3)where

U_f is the shearing velocity of bed surface,

ρ_s is the density of the sediment particle,

ρ_f is the fluid density, g is the acceleration of gravity, d

₅₀ is the median size of sediment, and μ is the dynamic viscosity of sediment.And each sediment particle suspended in the fluid obeys the equations for mass conservation and energy conservation

∂𝑐𝑠∂𝑡+∇⋅(𝑢𝑐𝑠)=0,∂��∂�+∇⋅(�¯��)=0,(4)

∂𝑢𝑠∂𝑡+𝑢⋅∇𝑢𝑠=−1𝜌𝑠∇𝑃+𝐹−𝐾𝑓𝑠𝜌𝑠𝑢𝑟,∂��∂�+�¯⋅∇��=−1��∇�+�−��,(5)where

c_s is the concentration of the sediment particle,

𝑢�¯ is the mean velocity vector of the fluid and the sediment particle,

u_s is the velocity of the sediment particle,

f_s is the volume fraction of the sediment particle, P is the pressure, F is the volumetric and viscous force, K is the drag force, and

u_r is the relative velocity.

3. Numerical Setup and Modeling

In this paper, a three-dimensional submarine cable local scouring simulation model is established by FLOW-3D. Based on the numerical simulation, the process of the submarine cable, which gradually changes from semi-exposed to the spanning state under the steady-state ocean current, is studied. The geometric modeling, the mesh division, the physical field setup, and the grid independent test of CFD numerical model are as follows.

3.1. Geometric Modeling and Mesh Division

A three-dimensional (3D) numerical model of the local scouring of a semi-exposed submarine cable is established, which is shown in Figure 1. The dimensions of the model are marked in Figure 1. The inlet direction of the ocean current is defined as the upstream of the submarine cable (referred to as upstream), and the outlet direction of the ocean current is defined as the downstream of the submarine cable (referred to as downstream).

Figure 1. Three-dimensional finite element model of local scouring of semi-exposed submarine cable.

The submarine cable with a diameter of 0.2 m is positioned on sediment that is initially in a semi-exposed state. When the length of the span is short, the submarine cable will not show obvious deformation due to gravity or scouring from the ocean current. Therefore, the submarine cable surface is set as the fixed boundary. The model’s left boundary is set as the inlet, the right boundary is set as the outlet, the front and rear boundaries are set as symmetry, and the bottom boundary is set as the non-slip wall. Since the water depth above the submarine cable is more than 0.6 m in practice, the top boundary of the model is also set as symmetry. The sediment near the inlet and the outlet will be carried by ocean currents, which leads to the abnormal scouring terrain. At each end of the sediment, a baffle (thickness of 3 cm) is installed to ensure that the simulation results can reflect the real situation.

Due to the fact that the flow field around the semi-exposed submarine cable is not a simple two-dimensional symmetrical distribution, it should be solved by three-dimensional numerical simulation. Considering the accuracy and efficiency of the calculation, the size of mesh is set to 0.02 m. The total number of meshes after the dissection is 133,254.

3.2. Physical Field Setup

The CFD finite element model contains four physical field modules: sediment scouring module, gravity and non-inertial reference frame module, density evaluation module, and viscosity and turbulence module. In this paper, the renormalization group (RNG) k–ε turbulence model is used, which has high computational accuracy for turbulent vortices. Therefore, this turbulence model is suitable for calculating the sediment scouring process around the semi-exposed submarine cable [25]. The key parameters of the numerical simulation are referring to the survey results of submarine sediments in the Korean Peninsula [26], as listed in Table 1.Table 1. Key parameters of numerical simulation.

3.3. Mesh Independent Test

In order to eliminate errors caused by the quantity of grids in the calculation process, two sizes of mesh are set on the validation model, and the scour profiles under different mesh sizes are compared. The validation model is shown in Figure 2, and the scouring terrain under different mesh size is given in Figure 3.

Figure 2. Validation model.

Figure 3. Scouring terrain under different mesh sizes.

It can be seen from Figure 3 that with the increase in the number of meshes, the scouring terrain of the verification model changes slightly, and the scouring depth is basically unchanged. Considering the accuracy of the numerical simulation and the calculation’s time cost, it is reasonable to consider setting the mesh size to 0.02 m.

4. Results and Analysis

4.1. Analysis of Local Scouring Process

Based on the CFD finite element numerical simulation, the local scouring process of the submarine cable under the steady-state ocean current is analyzed. The end time of the simulation is 9 h, the initial time step is 0.01 s, and the fluid velocity is 0.40 m/s. Simulation results are saved every minute. Figure 4 illustrates the scouring terrain around the semi-exposed submarine cable, which has been scoured by the steady-state current for 5 h.

Figure 4. Scouring terrain around semi-exposed submarine cable (scour for 5 h).

As can be seen from Figure 4, three scouring holes were separately formed in the upstream wake position and downstream of the semi-exposed submarine cable. The scouring holes are labeled according to their locations. The variation of the scouring terrain around the semi-exposed submarine cable over time is given in Figure 5. The red circle in the picture corresponds to the position of the submarine cable, and the red box in the legend marks the time when the submarine cable is spanning.

Figure 5. Variation of scouring terrain around semi-exposed submarine cable adapted to time.

From Figure 5, in the first hour of scouring, the upstream (−0.5 m to −0.1 m) and downstream (0.43 m to 1.5 m) scouring holes appeared. The upstream scouring hole was relatively flat with depth of 0.04 m. The depth of the downstream scouring hole increased with the increase in distance, and the maximum depth was 0.13 m. The scouring hole that developed at the wake position was very shallow, and its depth was only 0.007 m.

In the second hour of scouring, the upstream scouring hole’s depth remained nearly constant. The depth of the downstream scouring hole only increased by 0.002 m. The scouring hole at the wake position developed steadily, and its depth increased from 0.007 m to 0.014 m.

The upstream and downstream scouring holes did not continue to develop during the third to the sixth hour. Compared to the first two hours, the development of scouring holes at the wake position accelerated significantly, with an average growth rate of 0.028 m/h. The growth rate in the fifth hour of the scouring hole at the wake position was slightly faster than the other times. After 6 h of scouring, the sediment on the right side of the submarine cable had been hollowed out.

In the seventh and the eighth hour of scouring, the upstream scouring hole’s depth increased slightly, the downstream scouring hole still remained stable, and the depth of the scouring hole at wake position increased by 0.019 m. The sediment under the submarine cable was gradually eroded as well. By the end of the eighth hour, the lower right part of the submarine cable had been exposed to water as well.

At 8 h 21 min of the scouring, the submarine cable was completely spanned, and the scouring holes were connected to each other. Within the next 10 min, the development of the scouring holes sped up significantly, and the maximum depth of scouring holes increased greatly to 0.27 m.

In reference [17], researchers have studied the local scouring process of semi-buried pipelines in sandy riverbeds through experiments. The test results show that the scouring process can be divided into a start-up stage, micropore formation stage, extension stage, and equilibrium stage. In this paper, the first three stages are simulated, and the results are in good agreement with the experiment, which proves the accuracy of the present numerical model.

In this research, the velocity of ocean currents at the sediment surface is defined as the shear velocity, which plays an important role in the process of local scouring. Figure 6 provides visual data on how the shear velocity varies over time.

Figure 6. Shear velocity changes in the scouring process.

The semi-exposed submarine cable protrudes from the seabed, which makes the shear velocity of its surface much higher than other locations. After the submarine cable is spanned, the shear velocity of the scouring hole surface below it is taken. This is the reason for the sudden change of shear velocity at the submarine cable’s location in Figure 6.The shear velocity in the initial state of the upstream scouring hole is obviously greater than in subsequent times. After 1 h of scouring, the shear velocity in the upstream scouring hole rapidly decreased from 1.1 × 10

⁻² m/s to 3.98 × 10

⁻³ m/s and remained stable until the end of the sixth hour. This phenomenon explains why the upstream scouring hole developed rapidly in the first hour but remained stable for the following 5 h.The shear velocity in the downstream scouring hole reduced at first and then increased; its initial value was 1.41 × 10

⁻² m/s. It took approximately 5 h for the shear velocity to stabilize, and the stable shear velocity was 2.26 × 10

⁻³ m/s. Therefore, compared with the upstream scouring hole, the downstream scouring hole was deeper and required more time to reach stability.The initial shear velocity in the scouring hole at the wake position was only 7.1 × 10

⁻³ m/s, which almost does not change in the first hour. This leads to a very slow development of the scouring hole at the wake position in the early stages. The maximum shear velocity in this scouring hole gradually increased to 1.05 × 10

⁻² m/s from the second to the fifth hour, and then decreased to 6.61 × 10

⁻³ m/s by the end of the eighth hour. This is why the scouring hole at the wake position grows fastest around the fifth hour. Consistent with the pattern of change in the scouring hole’s terrain, the location of the maximal shear velocity also shifted to the right with time.

The shear velocity of all three scouring holes rose dramatically in the last hour. Combined with the terrain in Figure 5, this can be attributed to the complete spanning of the submarine cable.

From Equations (3)–(5), one can see the movement of the sediment is related directly with the sediment’s critical Shields number, sediment density, and ocean current velocity. Based on the parameters in Table 1, the influence of the above parameters on the local scouring process of semi-exposed submarine cables will be discussed.

4.2. Influence Factors

4.2.1. Sediment’s Critical Shields Number

The sediment’s critical Shields number

θ_cr is set as 0.02, 0.03, 0.04, 0.05, 0.06, and 0.07, and the variations of scouring terrain over time under each

θ_cr are displayed in Figure 7.

Figure 7. Influence of sediment’s critical Shields number

θ_cr on local scouring around semi-exposed submarine cable: (a

) θ_cr = 0.02; (b

) θ_cr = 0.03; (c

) θ_cr = 0.04; (d

) θ_cr = 0.05; (e

) θ_cr = 0.06; and (f

) θ_cr = 0.07.From Figure 7, one can see that a change in

θ_cr will affect the depth of the upstream scouring hole and the development speed of the scouring hole at the wake position, but it will have no significant impact on the expansion of the downstream scouring hole.Under conditions of different

θ_cr, the upstream scouring hole will reach a temporary plateau within 1 h, at which time the stable depth will be about 0.04 m. When

θ_cr ≤ 0.05, the upstream scouring hole will continue to expand after a few hours. The stable time is obviously affected by

θ_cr, which will gradually increase from 1 h to 11 h with the increase in

θ_cr. The terrain of the upstream scouring hole will gradually convert to deep on the left and to shallow on the right. Since the scouring hole at the wake position has not been stable, its state at the time of submarine cable spanning is studied emphatically. In the whole process of scouring, the scouring hole at the wake position continues to develop and does not reach a stable state. With the increase in

θ_cr, the development velocity of the scouring hole at the wake position will decrease considerably. Its average evolution velocity decreases from 3.88 cm/h to 1.62 cm/h, and its depth decreases from 21.9 cm to 18.8 cm. Under the condition of each

θ_cr, the downstream scouring hole will stabilize within 1 h, and the stable depth will be basically unchanged (all about 13.5 cm).As

θ_cr increases, so does the sediment’s ability to withstand shearing forces, which will cause it to become increasingly difficult to be eroded or carried away by ocean currents. This effect has been directly reflected in the depth of scouring holes (upstream and wake position). Due to the blocking effect of semi-exposed submarine cables, the wake is elongated, which is why the downstream scouring hole develops before the scouring hole at the wake position and quickly reaches a stable state. However, due to the high wake intensity, this process is not significantly affected by the change of

θ_cr.

4.2.2. Sediment Density

The density of sediment

ρ_s is set as 1550 kg/m

³, 1600 kg/m

³, 1650 kg/m

³, 1700 kg/m

³, 1750 kg/m

³, and 1800 kg/m

³, and the variation of scouring terrain over time under each

ρ_s are displayed in Figure 8.

Figure 8. Influence of sediment density

ρ_s on local scouring around semi-exposed submarine cable: (a

) ρ_s = 1550 kg/m

³; (b) ρ_s = 1600 kg/m

³; (c) ρ_s = 1650 kg/m

³; (d) ρ_s = 1700 kg/m

³; (e) ρ_s = 1750 kg/m

³; and (f

) ρ_s = 1800 kg/m

³.From Figure 8, one can see that a change in

ρ_s will also affect the depth of the upstream scouring hole and the development speed of the scouring hole at the wake position. In addition, it can even have an impact on the downstream scouring hole depth.Under different

ρ_s conditions, the upstream scouring hole will always reach a temporary stable state in 1 h, at which time the stable depth will be 0.04 m. When

ρ_s ≤ 1750 kg/m

³, the upstream scouring hole will continue to expand after a few hours. The stabilization time of upstream scouring hole is more clearly affected by

ρ_s, which will gradually increase from 3 h to 13 h with the increase in

ρ_s. The terrain of the upstream scouring hole will gradually change to deep on the left and to shallow on the right. Since the scouring hole at the wake position has not been stable, its state at the time of the submarine cable spanning is studied emphatically, too. In the whole process of scouring, the scouring hole at the wake position continues to develop and does not reach a stable state. When

ρ_s is large, the development rate of scouring hole obviously decreased with time. With the increase in

ρ_s, the development velocity of the scouring hole at the wake position reduces from 3.38 cm/h to 1.14 cm/h, and the depth of this scouring hole declines from 20 cm to 15 cm. As

ρ_s increases, the stabilization time of the downstream scouring hole increases from less than 1 h to about 2 h, but the stabilization depth of the downstream scouring hole remains essentially the same (all around 13.5 cm).As can be seen from Equation (1), the increase in

ρ_s will reduce the Shields number, thus weakening the shear action of the sediment by the ocean current, which explains the extension of the stability time of the upstream scouring hole. At the same time, with the increase in the depth of scouring hole at the wake position, its shear velocity will decreases. Therefore, under a larger

ρ_s value, the development speed of scouring hole at the wake position will decrease significantly with time. Possibly for the same reason,

ρ_s can affect the development rate of downstream scouring hole.

4.2.3. Ocean Current Velocity

The ocean current velocity v is set as 0.35 m/s, 0.40 m/s, 0.45 m/s, 0.50 m/s, 0.55 m/s, and 0.60 m/s. Figure 9 presents the variation in scouring terrain with time for each v.

Figure 9. Influence of ocean current velocity v on local scouring around semi-exposed submarine cable: (a) v = 0.35 m/s; (b) v = 0.40 m/s; (c) v = 0.45 m/s; (d) v = 0.50 m/s; (e) v = 0.55 m/s; and (f) v = 0.60 m/s.

Changes in v affect the depth of the upstream and downstream scouring holes, as well as the development velocity of the wake position and downstream scouring holes.

When v ≤ 0.45 m/s, the upstream scouring hole will reach a temporary stable state within 1 h, at which point the stable depth will be 0.04 m. The stabilization time of the upstream scouring hole is affected by v, which will gradually decrease from 15 h to 3 h with the increase in v. When v > 0.45 m/s, the upstream scouring hole is going to expand continuously. With the increase in v, its average development velocity increases from 6.68 cm/h to 8.66 cm/h, and its terrain changes to deep on the left and to shallow on the right. When the submarine cable is spanning, special attention should be paid to the depth of the scouring hole at the wake position. Throughout whole scouring process, the scouring hole at the wake position continues to develop and does not reach a stable state. With the increase in v, the depth of scouring hole at the wake position will increase from 14 cm to 20 cm, and the average development velocity will increase from 0.91 cm/h to 10.43 cm/h. As v increases, the time required to stabilize the downstream scouring hole is shortened from 1to 2 h to less than 1 h, but the stable depth is remains nearly constant at 13.5 cm.

An increase in v will increase the shear velocity. Therefore, when the depth of the scouring hole increases, the shear velocity in the hole will also increase, which can deepen both the upstream and downstream scouring hole. According to Equation (1), the Shields number is proportional to the square of the shear velocity. The increase in shear velocity significantly intensifies local scouring, which increases the development rate of scouring holes at the wake position and downstream.

4.3. Variation Rule of Spanning Time

In this paper, the spanning time is defined as the time taken for a semi-exposed submarine cable (initial state) to become a spanning submarine cable. Figure 10 illustrates the effect of the above parameters on the spanning time of the semi-exposed submarine cable.

Figure 10. Influence of different parameters on spanning time of the semi-exposed submarine cable: (a) Sediment critical Shields number; (b) Sediment density; and (c) Ocean current velocity.From Figure 10a, the spanning time monotonically increases with the increase in the critical Shields number of sediment. However, the slope of the curve decreases first and then increases, and the inflection point is at

θ_cr = 4.59 × 10

⁻². The relationship between spanning time t and sediment’s critical Shields number

θ_cr can be formulated by a cubic function as shown in Equation (6):

𝑡=−2.98+6.76𝜃𝑐𝑟−1.45𝜃2𝑐𝑟+0.11𝜃3𝑐𝑟.�=−2.98+6.76��−1.45��2+0.11��3.(6)It can be seen from Figure 10b that with the increase in the sediment density, the spanning time increases monotonically and linearly. The relationship between the spanning time t and the sediment’s density

ρ_s can be formulated by the first order function as shown in Equation (7):

𝑡=−41.59+30.54𝜌𝑠.�=−41.59+30.54��.(7)Figure 10c shows that with the increase in the ocean current velocity, the spanning time decreases monotonically. The slope of the curve increases with the increase in the ocean current velocity, so it can be considered that there is saturation of the ocean current velocity effect. The relationship between the spanning time t and the ocean current velocity v can be formulated by the exponential function

𝑡=0.15𝑣−4.38.�=0.15�−4.38.(8)

5. Conclusions

In this paper, a three-dimensional CFD finite element numerical simulation model is established, which is used to research the local scouring process of the semi-exposed submarine cable under the steady-state ocean current. The relationship between shear velocity and scouring terrain is discussed, the influence of sediment critical Shields number, sediment density and ocean current velocity on the local scouring process is analyzed, and the variation rules of the spanning time of the semi-exposed submarine cable is given. The conclusions are as follows:

Under the steady-state ocean currents, scouring holes will be formed at the upstream, wake position and downstream of the semi-exposed submarine cable. The upstream and downstream scouring holes develop faster, which will reach a temporary stable state at about 1 h after the start of the scouring. The scouring hole at the wake position will continue to expand at a slower rate and eventually lead to the spanning of the submarine cable.
There is a close relationship between the distribution of shear velocity and the scouring terrain. As the local scouring process occurs, the location of the maximum shear velocity within the scouring hole shifts and causes the bottom of the hole to move as well.
When the sediment’s critical Shields number and density are significantly large and ocean current velocity is sufficiently low, the duration of the stable state of the upstream scouring hole will be prolonged, and the average development velocity of the scouring holes at the wake position and downstream will be reduced.
The relationship between the spanning time and the critical Shields number θ_cr can be formulated as a cubic function, in which the curve’s inflection point is θ_cr = 4.59 × 10⁻². The relationship between spanning time and sediment density can be formulated as a linear function. The relationship between spanning time and ocean current velocity can be formulated by exponential function.

Based on the conclusions of this paper, even when it is too late to take measures or when the exposed position of the submarine cable cannot be located, the degree of burial depth development still can be predicted. This prediction is important for the operation and maintenance of the submarine cable. However, the study still leaves something to be desired. Only the local scouring process under the steady-state ocean current was studied, which is an extreme condition. In practice, exposed submarine cables are more likely to be scoured by reciprocating ocean currents. In the future, we will investigate the local scouring of submarine cables under the reciprocating ocean current.

Author Contributions

Conceptualization, Y.H. and Q.L.; methodology, Q.L., P.Z. and H.T.; software, Q.L.; validation, Q.L., L.C. and W.T.; writing—original draft preparation, Q.L.; writing—review and editing, Y.H. and Q.L.; supervision, Y.H. and L.Y. All authors have read and agreed to the published version of the manuscript.

Funding

This research was funded by the [Smart Grid Joint Fund Key Project between National Natural Science Foundation of China and State Grid Corporation] grant number [U1766220].

Institutional Review Board Statement

Not applicable.

Informed Consent Statement

Not applicable.

Data Availability Statement

The data supporting the reported results cannot be shared at this time, as they have been used in producing more publications on this research.

Acknowledgments

This work is supported by the Smart Grid Joint Fund Key Project of the National Natural Science Foundation of China and State Grid Corporation (Grant No. U1766220).

Conflicts of Interest

The authors declare no conflict of interest.

References

Taormina, B.; Bald, J.; Want, A.; Thouzeau, G.; Lejart, M.; Desroy, N.; Carlier, A. A review of potential impacts of submarine power cables on the marine environment: Knowledge gaps, recommendations and future directions. Renew. Sust. Energ. Rev. 2018, 96, 380–391. [Google Scholar] [CrossRef]
Gulski, E.; Anders, G.J.; Jogen, R.A.; Parciak, J.; Siemiński, J.; Piesowicz, E.; Paszkiewicz, S.; Irska, I. Discussion of electrical and thermal aspects of offshore wind farms’ power cables reliability. Renew. Sust. Energ. Rev. 2021, 151, 111580. [Google Scholar] [CrossRef]
Wang, W.; Yan, X.; Li, S.; Zhang, L.; Ouyang, J.; Ni, X. Failure of submarine cables used in high-voltage power transmission: Characteristics, mechanisms, key issues and prospects. IET Gener. Transm. Distrib. 2021, 15, 1387–1402. [Google Scholar] [CrossRef]
Chen, H.; Chen, Z.; Lu, H.; Wu, C.; Liang, J. Protection method for submarine cable detection and exposed suspension problem in Qiongzhou straits. Telecom Pow. Technol. 2019, 36, 60–61+63. [Google Scholar]
Zhu, J.; Ren, B.; Dong, P.; Chen, W. Vortex-induced vibrations of a free spanning submarine power cable. Ocean Eng. 2023, 272, 113792. [Google Scholar] [CrossRef]
Sumer, B.M.; Jensen, H.R.; Mao, Y.; Fredsøe, J. Effect of lee-wake on scour below pipelines in current. J. Waterw. Port Coast. Ocean. Eng. 1988, 114, 599–614. [Google Scholar] [CrossRef]
Chiew, Y.M. Prediction of maximum scour depth at submarine pipelines. J. Hydraul. Eng. 1991, 117, 452–466. [Google Scholar] [CrossRef]
Mastbergen, D.R.; Vandenberg, J.H. Breaching in fine sands and the generation of sustained turbidity currents in submarine canyons. Sedimentology 2003, 50, 625–637. [Google Scholar] [CrossRef]
Dey, S.; Singh, N.P. Clear-water scour depth below underwater pipelines. J. Hydro-Env. Res. 2007, 1, 157–162. [Google Scholar] [CrossRef]
Dey, S.; Singh, N.P. Clear-water scour below underwater pipelines under steady flow. J. Hydraul. Eng. 2008, 134, 588–600. [Google Scholar] [CrossRef]
Liang, D.; Cheng, L. Numerical study of scour around a pipeline bundle. Proc. Inst. Civil Eng. Mar. Eng. 2008, 161, 89–95. [Google Scholar] [CrossRef]
Yang, L.; Guo, Y.; Shi, B.; Kuang, C.; Xu, W.; Cao, S. Study of scour around submarine pipeline with a rubber plate or rigid spoiler in wave conditions. J. Waterw. Port Coast. Ocean Eng. 2012, 138, 484–490. [Google Scholar] [CrossRef]
Li, Y.; Ong, M.C.; Fuhrman, D.R.; Larsen, B.E. Numerical investigation of wave-plus-current induced scour beneath two submarine pipelines in tandem. Coast. Eng. 2020, 156, 103619. [Google Scholar] [CrossRef]
Guan, D.; Hsieh, S.C.; Chiew, Y.M.; Low, Y.M.; Wei, M. Local scour and flow characteristics around pipeline subjected to vortex-induced vibrations. J. Hydraul. Eng. 2020, 146, 04019048. [Google Scholar] [CrossRef]
Liu, M.M.; Jin, X.; Wang, L.; Yang, F.; Tang, J. Numerical investigation of local scour around a vibrating pipeline under steady currents. Ocean Eng. 2021, 221, 108546. [Google Scholar] [CrossRef]
Huang, J.; Yin, G.; Ong, M.C.; Myrhaug, D.; Jia, X. Numerical investigation of scour beneath pipelines subjected to an oscillatory flow condition. J. Mar. Sci. Eng. 2021, 9, 1102. [Google Scholar] [CrossRef]
Cui, F.; Du, Y.; Hao, X.; Peng, S.; Bao, Z.; Peng, S. Experimental study on local scour and related mechanical effects at river-crossing underwater oil and gas pipelines. Adv. Civ. Eng. 2021, 2021, 6689212. [Google Scholar] [CrossRef]
Li, B.; Ma, H. Scouring mechanism of suspended and partially-buried pipelines under steady flow. Coast. Eng. 2022, 177, 104201. [Google Scholar] [CrossRef]
Najafzadeh, M.; Oliveto, G. Scour propagation rates around offshore pipelines exposed to currents by applying data-driven models. Water 2022, 14, 493. [Google Scholar] [CrossRef]
Zhu, Y.; Xie, L.; Wong, T.; Su, T. Development of three-dimensional scour below pipelines in regular waves. J. Mar. Sci. Eng. 2022, 10, 124. [Google Scholar] [CrossRef]
Ma, H.; Li, B. CFD-CGDEM coupling model for scour process simulation of submarine pipelines. Ocean Eng. 2023, 271, 113789. [Google Scholar] [CrossRef]
Hu, K.; Bai, X.; Vaz, M.A. Numerical simulation on the local scour processing and influencing factors of submarine pipeline. J. Mar. Sci. Eng. 2023, 11, 234. [Google Scholar] [CrossRef]
Yang, B.; Gao, F.; Wu, Y. Experimental study on local scour of sandy seabed under submarine pipeline in unidirectional currents. Eng. Mech. 2008, 25, 206–210. [Google Scholar]
Cheng, Y.; Wang, X.; Luo, W.; Huang, X.; Lyu, X. Experimental study of local scour around a downstream inclined pile under combined waves and current. Adv. Eng. Sci. 2021, 53, 64–71. [Google Scholar]
Lu, Y.; Zhou, L.; Shen, X. Different turbulence models for simulating a liquid-liquid hydro cyclone. J. Tsinghua Univ. 2001, 41, 105–109. [Google Scholar]
Yun, D.H.; Kim, Y.T. Experimental study on settlement and scour characteristics of artificial reef with different reinforcement type and soil type. Geotext. Geomembr. 2018, 46, 448–454. [Google Scholar] [CrossRef]

원문 바로가기

미세한 퇴적물이 강바닥에 침투하고 하천 환경에 미치는 영향 – 연구 검토

Intrusion of fine sediments into river bed and its effect on river environment – a research review

Nilav Karna,K.S. Hari Prasad, Sanjay Giri & A.S. Lodhi

Abstract

Fine sediments enter into the river through various sources such as channel bed, bank, and catchment. It has been regarded as a type of pollution in river. Fine sediments present in a river have a significant effect on river health. Benthic micro-organism, plants, and large fishes, all are part of food chain of river biota. Any detrimental effect on any of these components of food chain misbalances the entire riverine ecosystem. Numerous studies have been carried out on the various environmental aspects of rivers considering the presence of fine sediment in river flow. The present paper critically reviews many of these aspects to understand the various environmental impacts of suspended sediment on river health, flora and fauna.

Keywords:

Introduction
The existence of fine sediment in a river system is a natural phenomenon. But in many cases it is exacerbated by the manmade activities. The natural cause of fines being in flow generally keeps the whole system in equilibrium except during some calamites whereas anthropogenic activities leading to fines entering into the flow puts several adverse impacts on the entire river system and its ecology. Presence of fines in flow is considered as a type of pollution in water. In United States,
the fine sediment in water along with other non point source pollution is considered as a major obstacle in providing quality water for fishes and recreation activities (Diplas and Parker 1985).
Sediments in a river are broadly of two types, organic and inorganic, and they both move in two ways either along the bed of the channel called bed load or in suspension called suspended load and their movements depend upon fluid flow and sediment characteristics. Further many investigators have divided the materials in suspension into two different types.
One which originates from channel bed and bank is called bed material suspended load and another that migrates from feeding catchment area is called wash load. A general perception is that wash loads are very fine materials like clay, silt but it may not always be true (Woo et al. 1986). In general, suspended materials are of size less than 2 mm. The impact of sand on the various aspects of river is comparatively less than that of silt and clay. The latter are chemically active and good carrier of many contaminants and nutrients such as dioxins, phosphorous, heavy and trace metals, polychlorinated biphenyl (PCBs), radionuclide, etc. (Foster and Charlesworth 1996; Horowitz et al. 1995; Owens et al. 2001; Salomons and Förstner 1984; Stone and Droppo 1994; Thoms 1987). Foy and Bailey-Watt (1998) reported that out of 129 lakes in England and Wales, 69% have phosphorous contamination. Ten percent lakes, rivers, and bays of United States have sediment contaminants with chemicals as reported by USEPA. Several field and experimental studies have been conducted
considering, sand, silt, and clay as suspended material. Hence, the subject reported herein is based on considering the fine sediment size smaller than 2 mm.
Fine sediments have the ability to alter the hydraulics of the flow. Presence of fines in flow can change the magnitude of turbulence, it can change the friction resistance to flow. Fines can change the mobility and permeability of the bed material. In some extreme cases, fines in flow may even change the morphology of the river (Doeg and Koehn 1994; Nuttall 1972; Wright and Berrie 1987). Fines in the flow adversely affect the producer by increasing the turbidity, hindering the
photosynthesis process by limiting the light penetration. This is ultimately reflected in the entire food ecosystem of river (Davis-Colley et al. 1992; Van Niewenhuyre and Laparrieve 1986). In addition, abrasion due to flowing sediment kills the aquatic flora (Edwards 1969; Brookes 1986). Intrusion of fines into the pores of river bed reduces space for several invertebrates, affects the spawning process (Petts 1984; Richards and Bacon 1994; Schalchli 1992). There are several other direct
or indirect, short-term or long-term impacts of fines in river.
The present paper reports the physical/environmental significance of fines in river. The hydraulic significance of presence of fines in the river has been reviewed in another paper (Effect of fine sediments on river hydraulics – a research review – http://dx.doi.org/10.1080/09715010.2014.982001).

References

Adams, J.N., and Beschta, R.L. (1980). “Gravel bed composition in oregon coastal streams.” Can. J. Fish. Aquat.Sci., 37, 1514–1521.10.1139/f80-196 [Crossref], [Web of Science ®], [Google Scholar]
Alabaster, J.S., and Llyod, R.L. (1980). Water quality criteria for fresh water, Butterworth, London, 297. [Google Scholar]
Aldridge, D.W., Payne, B.S., and Miller, A.C. (1987). “The effects of intermittent exposure to suspended solids and turbulence on three species of freshwater mussels.” Environ. Pollution, 45, 17–28.10.1016/0269-7491(87)90013-3 [Crossref], [PubMed], [Web of Science ®], [Google Scholar]
Barton, B.A. (1977). “Short-term effects of highway construction on the limnology of a small stream in southern Ontario.” Freshwater Biol., 7, 99–108.10.1111/fwb.1977.7.issue-2 [Crossref], [Web of Science ®], [Google Scholar]
Bash, J., Berman, C., and Bolton, S. (2001). Effects of turbidity and suspended solids on salmonids, Center for Streamside Studies, University of Washington, Seattle, WA. [Google Scholar]
Baxter, C.V., and Hauer, F.R. (2000). “Geomorphology, hyporheic exchange, and selection of spawning habitat by bull trout (Salvelinus confuentus).” Can. J. Fish. Aquat.Sci., 57, 1470–1481.10.1139/f00-056 [Crossref], [Web of Science ®], [Google Scholar]
Berkman, H.E., and Rabeni, C.F. (1987). “Effect of siltation on stream fish communities.” Environ. Biol. Fish., 18, 285–294.10.1007/BF00004881 [Crossref], [Web of Science ®], [Google Scholar]
Beschta, R.L., and Jackson, W.L. (1979). “The intrusion of fine sediments into a stable gravel bed.” J. Fish. Res. Board Can., 36, 204–210.10.1139/f79-030 [Crossref], [Google Scholar]
Boon, P.J. (1988). “The impact of river regulation on invertebrate communities in the UK.” Reg. River Res. Manage., 2, 389–409.10.1002/(ISSN)1099-1646 [Crossref], [Google Scholar]
Brookes, A. (1986). “Response of aquatic vegetation to sedimentation downstream from river channelization works in England and Wales.” Biol. Conserv., 38, 352–367. [Crossref], [Web of Science ®], [Google Scholar]
Bruton, M.N. (1985). “The effects of suspensoids on fish.” Hydrobiologia, 125, 221–241.10.1007/BF00045937 [Crossref], [Web of Science ®], [Google Scholar]
Carling, P.A. (1984). “Deposition of fine and coarse sand in an open-work gravel bed.” Can. J. Fish. Aquat. Sci., 41, 263–270.10.1139/f84-030 [Crossref], [Web of Science ®], [Google Scholar]
Carling, P.A., and McCahon, C.P. (1987). “Natural siltation of brown trout (Salmo trutta L.) spawning gravels during low-flow conditions.” Regulated streams, J.F. Craig and J.B. Kemper, eds., Plenum Press, New York, NY, 229–244.10.1007/978-1-4684-5392-8 [Crossref], [Google Scholar]
Carter, J., Owens, P.N., Walling, D.E., and Leeks, G.J.L. (2003). “Fingerprinting suspended sediment sources in a large urban river system.” Sci. Total Environ., 314–316, 513–534.10.1016/S0048-9697(03)00071-8 [Crossref], [PubMed], [Web of Science ®], [Google Scholar]
Chang, H.H. (1988). Fluvial processes in river engineering, Krieger, Malabar Florida, 432. [Google Scholar]
Chapman, D.W. (1988). “Critical review of variables used to define effects of fines in redds of large salmonids.” Trans. Am. Fish. Soc., 117, 1–21.10.1577/1548-8659(1988)117<0001:CROVUT>2.3.CO;2 [Taylor & Francis Online], [Web of Science ®], [Google Scholar]
Church, M.A., Mclean, D.G., and Wolcott, J.F. (1987). “River bed gravel sampling and analysis.” Sediment transport in gravel-bed rivers, C.R. Thorne, J.C. Bathrust, and R.D. Hey, eds., John Willey, Chichester, 43–79. [Google Scholar]
Cline, L.D., Short, R.A., and Ward, J.V. (1982). “The influence of highway construction on the macroinvertebrates and epilithic algae of a high mountain stream.” Hydrobiologia, 96, 149–159.10.1007/BF02185430 [Crossref], [Web of Science ®], [Google Scholar]
Collins, A.L., Walling, D.E., and Leeks, G.J.L. (1997). “Fingerprinting the origin of fluvial suspended sediment in larger river basins: combining assessment of spatial provenance and source type.” Geografiska Annaler, 79A, 239–254.10.1111/1468-0459.00020 [Crossref], [Google Scholar]
Cordone, A.J., and Kelly, D.W. (1961). “The influence of inorganic sediment on the aquatic life of stream.” Calif. Fish Game, 47, 189–228. [Google Scholar]
Culp, J.M., Wrona, F.J., and Davies, R.W. (1985). “Response of stream benthos and drift to fine sediment depositionversus transport.” Can. J. Zool., 64, 1345–1351. [Crossref], [Web of Science ®], [Google Scholar]
Davies-Colley, R.J., Hickey, C.W., Quinn, J.M., and Ryan, P.A. (1992). “Effects of clay discharges on streams.” Hydrobiologia, 248, 215–234.10.1007/BF00006149 [Crossref], [Web of Science ®], [Google Scholar]
Dhamotharan, S., Wood, A., Parker, G., and Stefan, H. (1980). Bed load transport in a model gravel stream. Project Report No. 190. St. Anthony Falls Hydraulic Laboratory, University of Minnesota. [Google Scholar]
Diplas, P., and Parker, G. (1985). Pollution of gravel spawning grounds due to fine sediment. Project Report, No. 240. St. Anthony Falls Laboratory, University of Minnesota, Minneapolis, MN. [Google Scholar]
Doeg, T.J., and Koehn, J.D. (1994). “Effects of draining and desilting a small weir on downstream fish and macroinvertebrates.” Reg. River Res. Manage., 9, 263–277.10.1002/(ISSN)1099-1646 [Crossref], [Web of Science ®], [Google Scholar]
Droppo, I.G. (2001). “Rethinking what constitutes suspended sediment.” Hydrol. Process., 15, 1551–1564.10.1002/(ISSN)1099-1085 [Crossref], [Web of Science ®], [Google Scholar]
Droppo, I.G., and Ongley, E.D. (1994). “Flocculation of suspended sediment in rivers of southeastern Canada.” Water Res., 28, 1799–1809.10.1016/0043-1354(94)90253-4 [Crossref], [Web of Science ®], [Google Scholar]
Einstein, H.A. (1968). “Deposition of suspended particles in a gravel bed.” J. Hydraul. Eng., 94, 1197–1205. [Google Scholar]
Erman, D.C., and Ligon, F.K. (1988). “Effects of discharge fluctuation and the addition of fine sediment on stream fish and macroinvertebrates below a water-filtration facility.” Environ. Manage., 12, 85–97.10.1007/BF01867380 [Crossref], [Web of Science ®], [Google Scholar]
Farnsworth, K.L., and Milliman, J.D. (2003). “Effects of climatic and anthropogenic change on small mountainous rivers: the Salinas River example.” Global Planet. Change, 39, 53–64.10.1016/S0921-8181(03)00017-1 [Crossref], [Web of Science ®], [Google Scholar]
Foster, I.D.L., and Charlesworth, S.M. (1996). “Heavy metals in the hydrological cycle: trends and explanation.” Hydrol. Process., 10, 227–261.10.1002/(ISSN)1099-1085 [Crossref], [Web of Science ®], [Google Scholar]
Foy, R.H., and Bailey-Watts, A.E. (1998). “Observations on the spatial and temporal variation in the phosphorus status of lakes in the British Isles.” Soil Use Manage., 14, 131–138.10.1111/sum.1998.14.issue-s4 [Crossref], [Web of Science ®], [Google Scholar]
Frostick, L.E., Lucas, P.M., and Reid, I. (1984). “The infiltration of fine matrices into coarse-grained alluvial sediments and its implications for stratigraphical interpretation.” J. Geol. Soc. London, 141, 955–965.10.1144/gsjgs.141.6.0955 [Crossref], [Web of Science ®], [Google Scholar]
Gagnier, D.L., and Bailey, R.C. (1994). “Balancing loss of information and gains in efficiency in characterizing stream sediment samples.” J. North Am. Benthol. Soc., 13, 170–180.10.2307/1467236 [Crossref], [Web of Science ®], [Google Scholar]
Gammon, J.R. (1970). The effect of inorganic sediment on stream biota. Environmental Protection Agency, Water Pollution Control Research, Series, 18050 DWC 12/70. USGPO, Washington, DC. [Google Scholar]
Graham, A.A. (1990). “Siltation of stone-surface periphyton in rivers by clay-sized particles from low concentrations in suspention.” Hydrobiologia, 199, 107–115.10.1007/BF00005603 [Crossref], [Web of Science ®], [Google Scholar]
Greig, S.M., Sear, D.A., and Carling, P.A. (2005). “The impact of fine sediment accumulation on the survival of incubating salmon progeny: Implications for sediment management.” Sci. Total Environ., 344, 241–258.10.1016/j.scitotenv.2005.02.010 [Crossref], [PubMed], [Web of Science ®], [Google Scholar]
Harrod, T.R., and Theurer, F.D. (2002). “Sediment.” Agriculture, hydrology and water quality, P.M. Haygarth and S.C. Jarvis, eds., CABI, Wallingford, 502. [Crossref], [Google Scholar]
Horowitz, A.J., Elrick, K.A., Robbins, J.A., and Cook, R.B. (1995). “Effect of mining and related activities on the sediment trace element geochemistry of Lake Coeur D’Alene, Idaho, USA part II: Subsurface sediments.” Hydrol. Process., 9, 35–54.10.1002/(ISSN)1099-1085 [Crossref], [Web of Science ®], [Google Scholar]
Hynes, H.B.N. (1970). The ecology of running waters, Liverpool University Press, Liverpool. [Google Scholar]
Khullar, N.K. (2002). “Effect of wash load on transport of uniform and nonuniform sediments.” Ph.D. thesis, Indian Institute of Technology Roorkee. [Google Scholar]
Kondolf, G.M. (1995). “Managing bedload sediment in regulated rivers: Examples from California, USA.” Geophys. Monograph, 89, 165–176. [Google Scholar]
Kondolf, G.M. (1997). “Hungry water: effects of dams and gravel mining on river channels.” Environ. Manage., 21, 533–551.10.1007/s002679900048 [Crossref], [PubMed], [Web of Science ®], [Google Scholar]
Langer, O.E. (1980). “Effects of sedimentation on salmonid stream life.” Report on the Technical Workshop on Suspended Solids and the Aquatic Environment, K. Weagle, ed., Whitehorse. [Google Scholar]
Lemly, A.D. (1982). “Modification of benthic insect communities in polluted streams: combined effects of sedimentation and nutrient enrichment.” Hydrobiologia, 87, 229–245.10.1007/BF00007232 [Crossref], [Web of Science ®], [Google Scholar]
Levasseur, M., Bergeron, N.E., Lapointe, M.F., and Bérubé, F. (2006). “Effects of silt and very fine sand dynamics in Atlantic salmon (Salmo salar) redds on embryo hatching success.” Can. J. Fish. Aquat. Sci., 63, 1450–1459.10.1139/f06-050 [Crossref], [Web of Science ®], [Google Scholar]
Lewis, K. (1973a). “The effect of suspended coal particles on the life forms of the aquatic moss Eurhynchium riparioides (Hedw.).” Fresh Water Biol., 3, 251–257.10.1111/fwb.1973.3.issue-3 [Crossref], [Google Scholar]
Lewis, K. (1973b). “The effect of suspended coal particles on the life forms of the aquatic moss Eurhynchium riparioides (Hedw.).” Fresh Water Biol., 3, 391–395.10.1111/fwb.1973.3.issue-4 [Crossref], [Google Scholar]
Lisle, T. (1980). “Sedimentation of Spawning Areas during Storm Flows, Jacoby Creek, North Coastal California.” Presented at the fall meeting of the American Geophysical Union, San Francisco, CA. [Google Scholar]
Marchant, R. (1989). “Changes in the benthic invertebrate communities of the thomson river, southeastern Australia, after dam construction.” Reg. River Res. Manage., 4, 71–89.10.1002/(ISSN)1099-1646 [Crossref], [Google Scholar]
McNeil, W.J., and Ahnell, W.H. (1964). Success of pink salmon spawning relative to size of spawning bed material. US Fish and Wildlife Service. Special Scientific Report, Fisheries 469. Washington, DC. [Google Scholar]
Milhous, R.T. (1973). “Sediment transport in a gravel bottomed stream.” Ph.D. thesis, Oregon State University, Corvallis, OR. [Google Scholar]
Milliman, J.D., and Syvitski, J.P.M. (1992). “Geomorphic/tectonic control of sediment discharge to the oceans: the importance of small mountainous rivers.” J. Geol., 100, 525–544.10.1086/jg.1992.100.issue-5 [Crossref], [Web of Science ®], [Google Scholar]
Mohnakrishnan, A. (2001). Reservoir sedimentation, Seminar on Reservoir Sedimentation, Ooty. [Google Scholar]
Mohta, J.A., Wallbrink, P.J., Hairsine, P.B., and Grayson, R.B. (2003). “Determining the sources of suspended sediment in a forested catchment in southeastern Australia.” Water Resour. Res., 39, 1056. [Web of Science ®], [Google Scholar]
Morris, G.L. (1993). “A global perspective of sediment control measures in reservoirs.” Notes on sediment management in reservoirs, S. Fan and G. Morris, eds., Water Resources Publications, Colorado, 13–44. [Google Scholar]
Morris, L.G., and Fan, J. (2010). Reservoir Sedimentation hand book – design and management of dams, reservoirs and watershed for sustainable use. McGraw-Hill, 440 and 499. [Google Scholar]
Newcombe, C.P., and Macdonald, D.D. (1991). “Effects of suspended sediments on aquatic ecosystems.” North Am. J. Fish. Manage., 11, 72–82.10.1577/1548-8675(1991)011<0072:EOSSOA>2.3.CO;2 [Taylor & Francis Online], [Google Scholar]
Nuttal, P.M. (1972). “The effects of sand deposition upon the macroinvertebrate fauna of the River Camel, Cornwall.” Freshwater Biol., 2, 181–186.10.1111/fwb.1972.2.issue-3 [Crossref], [Google Scholar]
Olsson, T.I., and Petersen, B. (1986). “Effects of gravel size and peat material on embryo survival and alevin emergence of brown trout, Salmo trutta L.” Hydrobiologia, 135, 9–14.10.1007/BF00006453 [Crossref], [Web of Science ®], [Google Scholar]
Owens, P.N., Walling, D.E., and Leeks, G.J.L. (2000). “Tracing fluvial suspended sediment sources in the catchment of the River Tweed, Scotland, using composite fingerprints and a numerical mixing model.” Tracers in eomorphology, I.D.L. Foster, ed., Wiley, Chichester, 291–308. [Google Scholar]
Owens, P.N., Walling, D.E., Carton, J., Meharg, A.A., Wright, J., and Leeks, G.J.L. (2001). “Downstream changes in the transport and storage of sediment-associated contaminants (P, Cr and PCBs) in agricultural and industrialized drainage basins.” Sci. Total Environ., 266, 177–186.10.1016/S0048-9697(00)00729-4 [Crossref], [PubMed], [Web of Science ®], [Google Scholar]
Petts, G.E. (1984). Impounded rivers: Perspectives for ecological management, Wiley, Chichester, 326. [Google Scholar]
Phillips, J.M., and Walling, D.E. (1995). “An assessment of the effects of sample collection, storage and resuspension on the representativeness of measurements of the effective particle size distribution of fluvial suspended sediment.” Water Res., 29, 2498–2508.10.1016/0043-1354(95)00087-2 [Crossref], [Web of Science ®], [Google Scholar]
Quinn, J.M., Davies-Coley, R.J., Hickey, C.W., Vickers, M.L., and Ryan, P.A. (1992). “Effects of clay discharges on streams.” Hydrobiologia, 248, 235–247.10.1007/BF00006150 [Crossref], [Web of Science ®], [Google Scholar]
Reiser, D.W., and White, R.G. (1990). “Effects of stream flow reduction on Chinook salmon egg incubation and fry quality.” Rivers, 1, 110–118. [Google Scholar]
Richards, C., and Bacon, K.L. (1994). “Influence of fine sediment on macroibvertebrates colonization of surface and hyporheic stream substrate.” Great Basin Nat., 54, 106–113. [Google Scholar]
Richards, C., Host, G.H., and Arthur, J.W. (1993). “Identification of predominant environmental factors structuring stream macroinvertebrate communities within a large agricultural catchment.” Freshwater Biol., 29, 285–294.10.1111/fwb.1993.29.issue-2 [Crossref], [Web of Science ®], [Google Scholar]
Rosenberg, D.M., and Wiens, A.P. (1978). “Effects of sediment addition on macrobenthic invertebrates in a Northern Canadian River.” Water Res., 12, 753–763.10.1016/0043-1354(78)90024-6 [Crossref], [Web of Science ®], [Google Scholar]
Ryan, P.A. (1991). “Environmental effects of sediment on New Zealand streams: A review.” New Zeal. J. Mar. Freshwater Res., 25, 207–221.10.1080/00288330.1991.9516472 [Taylor & Francis Online], [Web of Science ®], [Google Scholar]
Salomons, W., and Förstner, U. (1984). Metals in the hydrocycle, Sringer Verglag, New York, NY.10.1007/978-3-642-69325-0 [Crossref], [Google Scholar]
Schalchli, U. (1992). “The clogging of coarse gravel river beds by fine sediment.” Hydrobiologia, 235–236, 189–197.10.1007/BF00026211 [Crossref], [Web of Science ®], [Google Scholar]
Scrivener, J.C., and Brownlee, M.J. (1989). “Effects of forest harvesting on spawning gravel and incubation survival of chum (Oncorhynchus keta) andcoho salmon (O. kisutch) in Carnation Creek, British Columbia.” Can. J. Fish. Aquat. Sci., 46, 681–696.10.1139/f89-087 [Crossref], [Web of Science ®], [Google Scholar]
Sear, D.A. (1993). “Fine sediment infiltration into gravel spawning beds within a regulated river experiencing floods: Ecological implications for salmonids.” Reg Rivers Res. Manage., 8, 373–390.10.1002/(ISSN)1099-1646 [Crossref], [Google Scholar]
Soutar, R.G. (1989). “Afforestation and sediment yields in British fresh waters.” Soil Use Manage., 5, 82–86.10.1111/sum.1989.5.issue-2 [Crossref], [Web of Science ®], [Google Scholar]
Stone, M., and Droppo, I.G. (1994). “In-channel surficial fine-grained sediment laminae: Part II: Chemical characteristics and implications for contaminant transport in fluvial systems.” Hydrol. Process., 8, 113–124.10.1002/(ISSN)1099-1085 [Crossref], [Web of Science ®], [Google Scholar]
Thoms, M.C. (1987). “Channel sedimentation within the urbanized River Tame, UK.” Reg. Rivers Res. Manage., 1, 229–246.10.1002/(ISSN)1099-1646 [Crossref], [Google Scholar]
Trimble, S.W. (1983). “A sediment budget for Coon Creek, Driftless area, Wisconsin, 1853–1977.” Am. J. Sci., 283, 454–474.10.2475/ajs.283.5.454 [Crossref], [Web of Science ®], [Google Scholar]
U.S. Department of Health, Education and Welfare. (1965). Environmental Health Practices in recreational Areas, Public Health Service, Publication No. 1195. [Google Scholar]
Van Nieuwenhuyse, E.E., and LaPerriere, J.D. (1986). “Effects of placer gold mining on primary production in subarctic streams of Alaska.” J. Am. Water Res. Assoc., 22, 91–99. [Crossref], [Google Scholar]
Vörösmarty, C.J., Meybeck, M., Fekete, B., Sharma, K., Green, P., and Syvitski, J.P.M. (2003). “Anthropogenic sediment retention: major global impact from registered river impoundments.” Global Planet. Change, 39, 169–190.10.1016/S0921-8181(03)00023-7 [Crossref], [Web of Science ®], [Google Scholar]
Walling, D.E. (1995). “Suspended sediment yields in a changing environment.” Changing river channels, A. Gurnell and G. Petts, eds., Wiley, Chichester, 149–176. [Google Scholar]
Walling, D.E., and Moorehead, D.W. (1989). “The particle size characteristics of fluvial suspended sediment: an overview.” Hydrobiologia, 176–177, 125–149.10.1007/BF00026549 [Crossref], [Web of Science ®], [Google Scholar]
Walling, D.E., Owens, P.N., and Leeks, G.J.L. (1999). “Fingerprinting suspended sediment sources in the catchment of the River Ouse, Yorkshire, UK.” Hydrol. Process., 13, 955–975.10.1002/(ISSN)1099-1085 [Crossref], [Web of Science ®], [Google Scholar]
Walling, D.E., Owens, P.N., Waterfall, B.D., Leeks, G.J.L., and Wass, P.D. (2000). “The particle size characteristics of fluvial suspended sediment in the Humber and Tweed catchments, UK.” Sci. Total Environ., 251–252, 205–222.10.1016/S0048-9697(00)00384-3 [Crossref], [PubMed], [Web of Science ®], [Google Scholar]
Wilbur, C.G. (1983). Turbidity in the aquatic environment: an environmental factor in fresh and oceanic waters, Charles C. Thomas, Springfield, IL, 133. [Google Scholar]
Woo, H.S., Julien, P.Y., and Richardson, E.V. (1986). “Washload and fine sediment load.” J. Hydraul. Eng., 112, 541–545.10.1061/(ASCE)0733-9429(1986)112:6(541) [Crossref], [Google Scholar]
Wood, P.J., and Armitage, P.D. (1997). “Biological effects of fine sediment in the lotic environment.” Environ. Manage., 21, 203–217.10.1007/s002679900019 [Crossref], [PubMed], [Web of Science ®], [Google Scholar]
Wooster, J.K., Dusterhoff, S.R., Cui, Y., Sklar, L.S., Dietrich, W.E., and Malko, M. (2008). “Sediment supply and relative size distribution effects on fine sediment infiltration into immobile gravels.” Water Res. Res., 44, 1–18. [Crossref], [Web of Science ®], [Google Scholar]
Wren, G.Daniel, Bennett, J.Sean, Barkdoll, D.Brian, and Khunle, A.Roger. (2000). Studies in suspended sediment and turbulence in open channel flows, USDA, Agriculture Research Service, Research Report No. 18. [Google Scholar]
Wright, J.F., and Berrie, A.D. (1987). “Ecological effects of groundwater pumping and a natural drought on the upper reaches of a chalk stream.” Reg. River Res. Manage., 1, 145–160.10.1002/(ISSN)1099-1646 [Crossref], [Google Scholar]
Zhang, H., Xia, M., Chen, S.J., Li, Z., and Xia, H.B. (1976). “Regulation of sediments in some medium and small-sized reservoirs on heavily silt-laden streams in China.” 12th International Commission on Large Dams (ICOLD) Congress, Q. 47, R. 32, Mexico City, 1123–1243. [Google Scholar]

Effects of pile-cap elevation on scour and turbulence around a complex bridge pier

복잡한 교각 주변의 세굴 및 난기류에 대한 말뚝 뚜껑 높이의 영향

ABSTRACT

이 연구에서는 세 가지 다른 말뚝 뚜껑 높이에서 직사각형 말뚝 캡이 있는 복잡한 부두 주변의 지역 세굴 및 관련 흐름 유체 역학을 조사합니다. 말뚝 캡 높이가 초기 모래층에 대해 선택되었으며, 말뚝 캡이 흐름에 노출되지 않고(사례 I), 부분적으로 노출되고(사례 II) 완전히 노출(사례 III)되도록 했습니다. 실험은 맑은 물 세굴 조건 하에서 재순환 수로에서 수행되었으며, 입자 이미지 유속계 (PIV) 기술을 사용하여 다른 수직면에서 순간 유속을 얻었습니다. 부분적으로 노출된 파일 캡 케이스는 최대 수세미 깊이(MSD)를 보여주었습니다. 사례 II에서 MSD가 발생한 이유는 난류 유동장 분석을 통해 밝혀졌는데, 이는 말뚝 캡이 흐름에 노출됨에 따라 더 높은 세굴 깊이를 담당하는 말뚝 가장자리에서 와류 생성에 지배적으로 영향을 미친다는 것을 보여주었습니다. 유동장에 대한 파일 캡의 영향은 평균 속도, 소용돌이, 레이놀즈 전단 응력 및 난류 운동 에너지 윤곽을 통해 사례 III에서 두드러지게 나타났지만 파일 캡이 베드에서 떨어져 있었기 때문에 파일 캡 모서리는 수세미에 직접적인 영향을 미치지 않았습니다.

In this study, the local scour and the associated flow hydrodynamics around a complex pier with rectangular pile-cap at three different pile-cap elevations are investigated. The pile-cap elevations were selected with respect to the initial sand bed, such that the pile-cap was unexposed (case I), partially exposed (case II), and fully exposed (case III) to the flow. The experiments were performed in a recirculating flume under clear-water scour conditions, and the instantaneous flow velocity was obtained at different vertical planes using the particle image velocimetry (PIV) technique. The partially exposed pile-cap case showed the maximum obtained scour-depth (MSD). The reason behind the MSD occurrence in case II was enunciated through the analysis of turbulent flow field which showed that as the pile-cap got exposed to the flow, it dominantly affected the generation of vortices from the pile-cap corners responsible for the higher scour depth. The effect of the pile-cap on the flow field was prominently seen in case III through the mean velocities, vorticity, Reynolds shear stresses and turbulent kinetic energy contours, but since the pile-cap was away from the bed, the pile-cap corners did not show any direct effect on the scour.

KEYWORDS:

References

Adrian, R. J. (2013). Structure of turbulent boundary layers. In Jeremy G. Venditti, James L. Best, Michael Church, & Richard J. Hardy (Eds.), Coherent flow structures at earth’s surface (pp. 17–24). John Wiley and Sons. [Crossref], [Google Scholar]
Adrian, R. J., & Westerweel, J. (2011). Particle image velocimetry, No. 30. Cambridge University Press. [Google Scholar]
Alemi, M., & Maia, R. (2018). Numerical simulation of the flow and local scour process around single and complex bridge piers. International Journal of Civil Engineering, 16(5), 475–487. https://doi.org/10.1007/s40999-016-0137-8 [Crossref], [Google Scholar]
Alemi, M., Pêgo, J. P., & Maia, R. (2019). Numerical simulation of the turbulent flow around a complex bridge pier on the scoured bed. European Journal of Mechanics – B/Fluids, 76, 316–331. https://doi.org/10.1016/j.euromechflu.2019.03.011 [Crossref], [Web of Science ®], [Google Scholar]
Amini, A., Hamidi, S., Shirzadi, A., Behmanesh, J., & Akib, S. (2021). Efficiency of artificial neural networks in determining scour depth at composite bridge piers. International Journal of River Basin Management, 19(3), 327–333. https://doi.org/10.1080/15715124.2020.1742138 [Taylor & Francis Online], [Web of Science ®], [Google Scholar]
Arneson, L. A., Zevenbergen, L. W., Lagasse, P. F., & Clopper, P. E. (2015). Evaluating scour at bridges, 5th ed. hydraulic engineering circular No. 18 (HEC-18). Federal Highway Administration. [Google Scholar]
Ataie-Ashtiani, B., & Aslani-Kordkandi, A. (2012). Flow field around side-by-side piers with and without a scour hole. European Journal of Mechanics – B/Fluids, 36, 152–166. https://doi.org/10.1016/j.euromechflu.2012.03.007 [Crossref], [Web of Science ®], [Google Scholar]
Ataie-Ashtiani, B., Baratian-Ghorghi, Z., & Beheshti, A. A. (2010). Experimental investigation of clear-water local scour of compound piers. Journal of Hydraulic Engineering, 136(6), 343–351. https://doi.org/10.1061/(ASCE)0733-9429(2010)136:6(343) [Crossref], [Web of Science ®], [Google Scholar]
Avallone, F., Discetti, S., Astarita, T., & Cardone, G. (2015). Convergence enhancement of single-pixel PIV with symmetric double correlation. Experiments in Fluids, 56(4), 71. https://doi.org/10.1007/s00348-015-1938-2 [Crossref], [Web of Science ®], [Google Scholar]
Beheshti, A. A., & Ataie-Ashtiani, B. (2010). Experimental study of three-dimensional flow field around a complex bridge pier. Journal of Engineering Mechanics, 136(2), 143–154. https://doi.org/10.1061/(ASCE)EM.1943-7889.0000073 [Crossref], [Web of Science ®], [Google Scholar]
Beheshti, A. A., & Ataie-Ashtiani, B. (2016). Scour hole influence on turbulent flow field around complex bridge piers. Flow, Turbulence and Combustion, 97(2), 451–474. https://doi.org/10.1007/s10494-016-9707-8 [Crossref], [Web of Science ®], [Google Scholar]
Cameron, S. M., Nikora, V. I., & Marusic, I. (2019). Drag forces on a bed particle in open-channel flow: Effects of pressure spatial fluctuations and very-large-scale motions. Journal of Fluid Mechanics, 863, 494–512. https://doi.org/10.1017/jfm.2018.1003 [Crossref], [Web of Science ®], [Google Scholar]
Cheng, N., & Emadzadeh, A. (2017). Laboratory measurements of vortex-induced sediment pickup rates. International Journal of Sediment Research, 32(1), 98–104. https://doi.org/10.1016/j.ijsrc.2016.04.005 [Crossref], [Web of Science ®], [Google Scholar]
Coleman, S. E. (2005). Clearwater local scour at complex piers. Journal of Hydraulic Engineering, 131(4), 330–334. https://doi.org/10.1061/(ASCE)0733-9429(2005)131:4(330) [Crossref], [Web of Science ®], [Google Scholar]
Das, S., & Mazumdar, A. (2015). Turbulence flow field around two eccentric circular piers in scour hole. International Journal of River Basin Management, 13(3), 343–361. https://doi.org/10.1080/15715124.2015.1012515 [Taylor & Francis Online], [Web of Science ®], [Google Scholar]
Esmaeili Varaki, M., Radice, A., Samira Hossini, S., & Fazl Ola, R. (2019). Local scour at a complex pier with inclined columns footed on capped piles: Effect of the pile arrangement and of the cap thickness and elevation. ISH Journal of Hydraulic Engineering, 1–10. https://doi.org/10.1080/09715010.2019.1702109 [Taylor & Francis Online], [Google Scholar]
Ferraro, D., Tafarojnoruz, A., Gaudio, R., & Cardoso, A. H. (2013). Effects of pile cap thickness on the maximum scour depth at a complex pier. Journal of Hydraulic Engineering, 139(5), 482–491. https://doi.org/10.1061/(ASCE)HY.1943-7900.0000704 [Crossref], [Web of Science ®], [Google Scholar]
Gaudio, R., Tafarojnoruz, A., & Calomino, F. (2012). Combined flow-altering countermeasures against bridge pier scour. Journal of Hydraulic Research, 50(1), 35–43. https://doi.org/10.1080/00221686.2011.649548 [Taylor & Francis Online], [Web of Science ®], [Google Scholar]
Gautam, P., Eldho, T., & Behera, M. (2016). Experimental study of scour around a complex pier with elliptical pile-cap. In J. Harris, R. Whitehouse, & S. Moxon (Eds.), Scour and Erosion: Proceedings of the 8th International Conference on Scour and Erosion (Oxford, UK, 12-15 September 2016) (pp. 759–765). CRC Press. [Crossref], [Google Scholar]
Gautam, P., Eldho, T. I., Mazumder, B. S., & Behera, M. R. (2019). Experimental study of flow and turbulence characteristics around simple and complex piers using PIV. Experimental Thermal and Fluid Science, 100, 193–206. https://doi.org/10.1016/j.expthermflusci.2018.09.010 [Crossref], [Web of Science ®], [Google Scholar]
Graf, W. H., & Istiarto, I. (2002). Flow pattern in the scour hole around a cylinder. Journal of Hydraulic Research, 40(1), 13–20. https://doi.org/10.1080/00221680209499869 [Taylor & Francis Online], [Web of Science ®], [Google Scholar]
Hjulstrom, F. (1935). Study of the morphological activity of Rivers as illustrated by the River fyris bulletin, vol. 25. Geological Institute of Upsala. [Google Scholar]
Kumar, A., & Kothyari, U. C. (2012). Three-dimensional flow characteristics within the scour hole around circular uniform and compound piers. Journal of Hydraulic Engineering, 138(5), 420–429. https://doi.org/10.1061/(ASCE)HY.1943-7900.0000527 [Crossref], [Web of Science ®], [Google Scholar]
Mashahir, M. B., Zarrati, A. R., & Rezayi, M. J. (2004). Time development of scouring around a bridge pier protected by collar. In Proceedings 2nd International Conference on Scour and Erosion (ICSE-2). November 14–17, 2004, Singapore. [Google Scholar]
Melville, B. W. (2008). The physics of local scour at bridge piers. In Proceedings of the 4th International Conference on Scour and Erosion (ICSE-4). November 5-7, 2008, Tokyo, Japan (pp. 28–40). [Google Scholar]
Melville, B. W., & Chiew, Y. M. (1999). Time scale for local scour at bridge piers. Journal of Hydraulic Engineering, 125(1), 59–65. https://doi.org/10.1061/(ASCE)0733-9429(1999)125:1(59) [Crossref], [Web of Science ®], [Google Scholar]
Melville, B. W., & Raudkivi, A. J. (1977). Flow characteristics in local scour at bridge piers. Journal of Hydraulic Research, 15(4), 373–380. https://doi.org/10.1080/00221687709499641 [Taylor & Francis Online], [Web of Science ®], [Google Scholar]
Moreno, M., Maia, R., & Couto, L. (2016a). Effects of relative column width and pile-cap elevation on local scour depth around complex piers. Journal of Hydraulic Engineering, 142(2), 04015051. https://doi.org/10.1061/(ASCE)HY.1943-7900.0001080 [Crossref], [Web of Science ®], [Google Scholar]
Moreno, M., Maia, R., & Couto, L. (2016b). Prediction of equilibrium local scour depth at complex bridge piers. Journal of Hydraulic Engineering, 142(11), 04016045. https://doi.org/10.1061/(ASCE)HY.1943-7900.0001153 [Crossref], [Web of Science ®], [Google Scholar]
Nezu, I., & Rodi, W. (1986). Open-channel flow measurements with a laser Doppler anemometer. Journal of Hydraulic Engineering, 112(5), 335–355. https://doi.org/10.1061/(ASCE)0733-9429(1986)112:5(335) [Crossref], [Web of Science ®], [Google Scholar]
Radice, A., & Tran, C. K. (2012). Study of sediment motion in scour hole of a circular pier. Journal of Hydraulic Research, 50(1), 44–51. https://doi.org/10.1080/00221686.2011.641764 [Taylor & Francis Online], [Web of Science ®], [Google Scholar]
Richardson, J. R., & York, K. (1999). Hydrodynamic countermeasures for local pier scour. Transportation Research Record: Journal of the Transportation Research Board, 1690(1), 186–192. https://doi.org/10.3141/1690-21 [Crossref], [Google Scholar]
Saw, E., Debue, P., Kuzzay, D., Daviaud, F., & Dubrulle, B. (2018). On the universality of anomalous scaling exponents of structure functions in turbulent flows. Journal of Fluid Mechanics, 837, 657–669. https://doi.org/10.1017/jfm.2017.848 [Crossref], [Web of Science ®], [Google Scholar]
Schlichting, H. (1968). Boundary layer theory (Vol. 960). McGraw-Hill. [Google Scholar]
Sheppard, D. M., Demir, H., & Melville, B. W. (2011). Scour at wide piers and long skewed piers (Vol. 682). Transportation Research Board. [Google Scholar]
Tafarojnoruz, A., Gaudio, R., & Calomino, F. (2012). Bridge pier scour mitigation under steady and unsteady flow conditions. Acta Geophysica, 60(4), 1076–1097. https://doi.org/10.2478/s11600-012-0040-x [Crossref], [Web of Science ®], [Google Scholar]
Tafarojnoruz, A., Gaudio, R., & Dey, S. (2010). Flow-altering countermeasures against scour at bridge piers: A review. Journal of Hydraulic Research, 48(4), 441–452. https://doi.org/10.1080/00221686.2010.491645 [Taylor & Francis Online], [Web of Science ®], [Google Scholar]
Tennekes, H., & Lumley, J. L. (1972). A first course in turbulence. MIT press. [Crossref], [Google Scholar]
Veerappadevaru, G., Gangadharaiah, T., & Jagadeesh, T. R. (2011). Vortex scouring process around bridge pier with a caisson. Journal of Hydraulic Research, 49(3), 378–383. https://doi.org/10.1080/00221686.2011.568195 [Taylor & Francis Online], [Web of Science ®], [Google Scholar]
Veerappadevaru, G., Gangadharaiah, T., & Jagadeesh, T. R. (2012). Temporal variation of vortex scour process around caisson piers. Journal of Hydraulic Research, 50(2), 200–207. https://doi.org/10.1080/00221686.2012.666832 [Taylor & Francis Online], [Web of Science ®], [Google Scholar]
Vijayasree, B. A., Eldho, T. I., Mazumder, B. S., & Ahmad, N. (2019). Influence of bridge pier shape on flow field and scour geometry. International Journal of River Basin Management, 17(1), 109–129. https://doi.org/10.1080/15715124.2017.1394315 [Taylor & Francis Online], [Web of Science ®], [Google Scholar]
Yang, Y., Melville, B. W., Sheppard, D. M., & Shamseldin, A. Y. (2018). Clear-water local scour at skewed complex bridge piers. Journal of Hydraulic Engineering, 144(6), 04018019. https://doi.org/10.1061/(ASCE)HY.1943-7900.0001458 [Crossref], [Web of Science ®], [Google Scholar]
Yang, Y., Melville, B. W., Macky, G. H., & Shamseldin, A. Y. (2020). Temporal evolution of clear-water local scour at aligned and skewed complex bridge piers. Journal of Hydraulic Engineering, 146(4), 04020026. https://doi.org/10.1061/(ASCE)HY.1943-7900.0001732 [Crossref], [Web of Science ®], [Google Scholar]

원문 보기

Figure 11. Sketch of scour mechanism around USAF under random waves.

Scour Characteristics and Equilibrium Scour Depth Prediction around Umbrella Suction Anchor Foundation under Random Waves

by Ruigeng Hu¹,Hongjun Liu²,Hao Leng¹,Peng Yu³ andXiuhai Wang^1,2,*

¹College of Environmental Science and Engineering, Ocean University of China, Qingdao 266000, China

²Key Lab of Marine Environment and Ecology (Ocean University of China), Ministry of Education, Qingdao 266000, China

³Qingdao Geo-Engineering Survering Institute, Qingdao 266100, China

^*Author to whom correspondence should be addressed.

J. Mar. Sci. Eng. 2021, 9(8), 886; https://doi.org/10.3390/jmse9080886

Received: 6 July 2021 / Revised: 8 August 2021 / Accepted: 13 August 2021 / Published: 17 August 2021

(This article belongs to the Section Ocean Engineering)

Download

Abstract

A series of numerical simulation were conducted to study the local scour around umbrella suction anchor foundation (USAF) under random waves. In this study, the validation was carried out firstly to verify the accuracy of the present model. Furthermore, the scour evolution and scour mechanism were analyzed respectively. In addition, two revised models were proposed to predict the equilibrium scour depth S_eq around USAF. At last, a parametric study was carried out to study the effects of the Froude number F_r and Euler number E_u for the S_eq. The results indicate that the present numerical model is accurate and reasonable for depicting the scour morphology under random waves. The revised Raaijmakers’s model shows good agreement with the simulating results of the present study when KC_s,p < 8. The predicting results of the revised stochastic model are the most favorable for n = 10 when KC_rms,a < 4. The higher F_r and E_u both lead to the more intensive horseshoe vortex and larger S_eq.

Keywords:

scour; numerical investigation; random waves; equilibrium scour depth; KC number

1. Introduction

The rapid expansion of cities tends to cause social and economic problems, such as environmental pollution and traffic jam. As a kind of clean energy, offshore wind power has developed rapidly in recent years. The foundation of offshore wind turbine (OWT) supports the upper tower, and suffers the cyclic loading induced by waves, tides and winds, which exerts a vital influence on the OWT system. The types of OWT foundation include the fixed and floating foundation, and the fixed foundation was used usually for nearshore wind turbine. After the construction of fixed foundation, the hydrodynamic field changes in the vicinity of the foundation, leading to the horseshoe vortex formation and streamline compression at the upside and sides of foundation respectively [1,2,3,4]. As a result, the neighboring soil would be carried away by the shear stress induced by vortex, and the scour hole would emerge in the vicinity of foundation. The scour holes increase the cantilever length, and weaken the lateral bearing capacity of foundation [5,6,7,8,9]. Moreover, the natural frequency of OWT system increases with the increase of cantilever length, causing the resonance occurs when the system natural frequency equals the wave or wind frequency [10,11,12]. Given that, an innovative foundation called umbrella suction anchor foundation (USAF) has been designed for nearshore wind power. The previous studies indicated the USAF was characterized by the favorable lateral bearing capacity with the low cost [6,13,14]. The close-up of USAF is shown in Figure 1, and it includes six parts: 1-interal buckets, 2-external skirt, 3-anchor ring, 4-anchor branch, 5-supporting rod, 6-telescopic hook. The detailed description and application method of USAF can be found in reference [13].

Figure 1. The close-up of umbrella suction anchor foundation (USAF).

Numerical and experimental investigations of scour around OWT foundation under steady currents and waves have been extensively studied by many researchers [1,2,15,16,17,18,19,20,21,22,23,24]. The seabed scour can be classified as two types according to Shields parameter θ, i.e., clear bed scour (θ < θ_cr) or live bed scour (θ > θ_cr). Due to the set of foundation, the adverse hydraulic pressure gradient exists at upstream foundation edges, resulting in the streamline separation between boundary layer flow and seabed. The separating boundary layer ascended at upstream anchor edges and developed into the horseshoe vortex. Then, the horseshoe vortex moved downstream gradually along the periphery of the anchor, and the vortex shed off continually at the lee-side of the anchor, i.e., wake vortex. The core of wake vortex is a negative pressure center, liking a vacuum cleaner. Hence, the soil particles were swirled into the negative pressure core and carried away by wake vortexes. At the same time, the onset of scour at rear side occurred. Finally, the wake vortex became downflow when the turbulence energy could not support the survival of wake vortex. According to Tavouktsoglou et al. [25], the scale of pile wall boundary layer is proportional to 1/ln(R_d) (R_d is pile Reynolds), which means the turbulence intensity induced by the flow-structure interaction would decrease with R_d increases, but the effects of R_d can be neglected only if the flow around the foundation is fully turbulent [26]. According to previous studies [1,15,27,28,29,30,31,32], the scour development around pile foundation under waves was significantly influenced by Shields parameter θ and KC number simultaneously (calculated by Equation (1)). Sand ripples widely existed around pile under waves in the case of live bed scour, and the scour morphology is related with θ and KC. Compared with θ, KC has a greater influence on the scour morphology [21,27,28]. The influence mechanism of KC on the scour around the pile is reflected in two aspects: the horseshoe vortex at upstream and wake vortex shedding at downstream.

KC=UwmTD��=�wm��(1)

where, U_wm is the maximum velocity of the undisturbed wave-induced oscillatory flow at the sea bottom above the wave boundary layer, T is wave period, and D is pile diameter.

There are two prerequisites to satisfy the formation of horseshoe vortex at upstream pile edges: (1) the incoming flow boundary layer with sufficient thickness and (2) the magnitude of upstream adverse pressure gradient making the boundary layer separating [1,15,16,18,20]. The smaller KC results the lower adverse pressure gradient, and the boundary layer cannot separate, herein, there is almost no horseshoe vortex emerging at upside of pile. Sumer et al. [1,15] carried out several sets of wave flume experiments under regular and irregular waves respectively, and the experiment results show that there is no horseshoe vortex when KC is less than 6. While the scale and lifespan of horseshoe vortex increase evidently with the increase of KC when KC is larger than 6. Moreover, the wake vortex contributes to the scour at lee-side of pile. Similar with the case of horseshoe vortex, there is no wake vortex when KC is less than 6. The wake vortex is mainly responsible for scour around pile when KC is greater than 6 and less than O(100), while horseshoe vortex controls scour nearly when KC is greater than O(100).

Sumer et al. [1] found that the equilibrium scour depth was nil around pile when KC was less than 6 under regular waves for live bed scour, while the equilibrium scour depth increased with the increase of KC. Based on that, Sumer proposed an equilibrium scour depth predicting equation (Equation (2)). Carreiras et al. [33] revised Sumer’s equation with m = 0.06 for nonlinear waves. Different with the findings of Sumer et al. [1] and Carreiras et al. [33], Corvaro et al. [21] found the scour still occurred for KC ≈ 4, and proposed the revised equilibrium scour depth predicting equation (Equation (3)) for KC > 4.

Rudolph and Bos [2] conducted a series of wave flume experiments to investigate the scour depth around monopile under waves only, waves and currents combined respectively, indicting KC was one of key parameters in influencing equilibrium scour depth, and proposed the equilibrium scour depth predicting equation (Equation (4)) for low KC (1 < KC < 10). Through analyzing the extensive data from published literatures, Raaijmakers and Rudolph [34] developed the equilibrium scour depth predicting equation (Equation (5)) for low KC, which was suitable for waves only, waves and currents combined. Khalfin [35] carried out several sets of wave flume experiments to study scour development around monopile, and proposed the equilibrium scour depth predicting equation (Equation (6)) for low KC (0.1 < KC < 3.5). Different with above equations, the Khalfin’s equation considers the Shields parameter θ and KC number simultaneously in predicting equilibrium scour depth. The flow reversal occurred under through in one wave period, so sand particles would be carried away from lee-side of pile to upside, resulting in sand particles backfilled into the upstream scour hole [20,29]. Considering the backfilling effects, Zanke et al. [36] proposed the equilibrium scour depth predicting equation (Equation (7)) around pile by theoretical analysis, and the equation is suitable for the whole range of KC number under regular waves and currents combined.

S/D=1.3(1−exp([−m(KC−6)])�/�=1.3(1−exp(−�(��−6))(2)

where, m = 0.03 for linear waves.

S/D=1.3(1−exp([−0.02(KC−4)])�/�=1.3(1−exp(−0.02(��−4))(3)

S/D=1.3γKwaveKhw�/�=1.3��wave�ℎw(4)

where, γ is safety factor, depending on design process, typically γ = 1.5, K_wave is correction factor considering wave action, K_hw is correction factor considering water depth.

S/D=1.5[tanh(hwD)]KwaveKhw�/�=1.5tanh(ℎw�)�wave�ℎw(5)

where, h_w is water depth.

S/D=0.0753(θθcr−−−√−0.5)0.69KC0.68�/�=0.0753(��cr−0.5)0.69��0.68(6)

where, θ is shields parameter, θ_cr is critical shields parameter.

S/D=2.5(1−0.5u/uc)xrelxrel=xeff/(1+xeff)xeff=0.03(1−0.35ucr/u)(KC−6)⎫⎭⎬⎪⎪�/�=2.5(1−0.5�/��)��=��/(1+��)��=0.03(1−0.35�cr/�)(��−6)(7)

where, u is near-bed orbital velocity amplitude, u_c is critical velocity corresponding the onset of sediment motion.

S/D=1.3{1−exp[−0.03(KC2lnn+36)1/2−6]}�/�=1.31−exp−0.03(��2ln�+36)1/2−6(8)

where, n is the 1/n’th highest wave for random waves

For predicting equilibrium scour depth under irregular waves, i.e., random waves, Sumer and Fredsøe [16] found it’s suitable to take Equation (2) to predict equilibrium scour depth around pile under random waves with the root-mean-square (RMS) value of near-bed orbital velocity amplitude U_m and peak wave period T_P to calculate KC. Khalfin [35] recommended the RMS wave height H_rms and peak wave period T_P were used to calculate KC for Equation (6). References [37,38,39,40] developed a series of stochastic theoretical models to predict equilibrium scour depth around pile under random waves, nonlinear random waves plus currents respectively. The stochastic approach thought the 1/n’th highest wave were responsible for scour in vicinity of pile under random waves, and the KC was calculated in Equation (8) with U_m and mean zero-crossing wave period T_z. The results calculated by Equation (8) agree well with experimental values of Sumer and Fredsøe [16] if the 1/10′th highest wave was used. To author’s knowledge, the stochastic approach proposed by Myrhaug and Rue [37] is the only theoretical model to predict equilibrium scour depth around pile under random waves for the whole range of KC number in published documents. Other methods of predicting scour depth under random waves are mainly originated from the equation for regular waves-only, waves and currents combined, which are limited to the large KC number, such as KC > 6 for Equation (2) and KC > 4 for Equation (3) respectively. However, situations with relatively low KC number (KC < 4) often occur in reality, for example, monopile or suction anchor for OWT foundations in ocean environment. Moreover, local scour around OWT foundations under random waves has not yet been investigated fully. Therefore, further study are still needed in the aspect of scour around OWT foundations with low KC number under random waves. Given that, this study presents the scour sediment model around umbrella suction anchor foundation (USAF) under random waves. In this study, a comparison of equilibrium scour depth around USAF between this present numerical models and the previous theoretical models and experimental results was presented firstly. Then, this study gave a comprehensive analysis for the scour mechanisms around USAF. After that, two revised models were proposed according to the model of Raaijmakers and Rudolph [34] and the stochastic model developed by Myrhaug and Rue [37] respectively to predict the equilibrium scour depth. Finally, a parametric study was conducted to study the effects of the Froude number (F_r) and Euler number (E_u) to equilibrium scour depth respectively.

2. Numerical Method

2.1. Governing Equations of Flow

The following equations adopted in present model are already available in Flow 3D software. The authors used these theoretical equations to simulate scour in random waves without modification. The incompressible viscous fluid motion satisfies the Reynolds-averaged Navier-Stokes (RANS) equation, so the present numerical model solves RANS equations:

∂u∂t+1VF(uAx∂u∂x+vAy∂u∂y+wAz∂u∂z)=−1ρf∂p∂x+Gx+fx∂�∂�+1��(��∂�∂�+��∂�∂�+��∂�∂�)=−1�f∂�∂�+��+��(9)

∂v∂t+1VF(uAx∂v∂x+vAy∂v∂y+wAz∂v∂z)=−1ρf∂p∂y+Gy+fy∂�∂�+1��(��∂�∂�+��∂�∂�+��∂�∂�)=−1�f∂�∂�+��+��(10)

∂w∂t+1VF(uAx∂w∂x+vAy∂w∂y+wAz∂w∂z)=−1ρf∂p∂z+Gz+fz∂�∂�+1��(��∂�∂�+��∂�∂�+��∂�∂�)=−1�f∂�∂�+��+��(11)

where, V_F is the volume fraction; u, v, and w are the velocity components in x, y, z direction respectively with Cartesian coordinates; A_i is the area fraction; ρ_f is the fluid density, f_i is the viscous fluid acceleration, G_i is the fluid body acceleration (i = x, y, z).

2.2. Turbulent Model

The turbulence closure is available by the turbulent model, such as one-equation, the one-equation k-ε model, the standard k-ε model, RNG k-ε turbulent model and large eddy simulation (LES) model. The LES model requires very fine mesh grid, so the computational time is large, which hinders the LES model application in engineering. The RNG k-ε model can reduce computational time greatly with high accuracy in the near-wall region. Furthermore, the RNG k-ε model computes the maximum turbulent mixing length dynamically in simulating sediment scour model. Therefore, the RNG k-ε model was adopted to study the scour around anchor under random waves [41,42].

∂kT∂T+1VF(uAx∂kT∂x+vAy∂kT∂y+wAz∂kT∂z)=PT+GT+DiffkT−εkT∂��∂�+1��(��∂��∂�+��∂��∂�+��∂��∂�)=��+��+��−��(12)

∂εT∂T+1VF(uAx∂εT∂x+vAy∂εT∂y+wAz∂εT∂z)=CDIS1εTkT(PT+CDIS3GT)+Diffε−CDIS2ε2TkT∂��∂�+1��(��∂��∂�+��∂��∂�+��∂��∂�)=��1��(��+��3��)+��−��2��2��(13)

where, k_T is specific kinetic energy involved with turbulent velocity, G_T is the turbulent energy generated by buoyancy; ε_T is the turbulent energy dissipating rate, P_T is the turbulent energy, Diff_ε and Diff_kT are diffusion terms associated with V_F, A_i; CDIS1, CDIS2 and CDIS3 are dimensionless parameters, and CDIS1, CDIS3 have default values of 1.42, 0.2 respectively. CDIS2 can be obtained from P_T and k_T.

2.3. Sediment Scour Model

The sand particles may suffer four processes under waves, i.e., entrainment, bed load transport, suspended load transport, and deposition, so the sediment scour model should depict the above processes efficiently. In present numerical simulation, the sediment scour model includes the following aspects:

2.3.1. Entrainment and Deposition

The combination of entrainment and deposition determines the net scour rate of seabed in present sediment scour model. The entrainment lift velocity of sand particles was calculated as [43]:

ulift,i=αinsd0.3∗(θ−θcr)1.5∥g∥di(ρi−ρf)ρf−−−−−−−−−−−−√�lift,i=��*0.3(�−�cr)1.5��(��−�f)�f(14)

where, α_i is the entrainment parameter, n_s is the outward point perpendicular to the seabed, d_* is the dimensionless diameter of sand particles, which was calculated by Equation (15), θ_cr is the critical Shields parameter, g is the gravity acceleration, d_i is the diameter of sand particles, ρ_i is the density of seabed species.

d∗=di(∥g∥ρf(ρi−ρf)μ2f)1/3�*=��(��f(��−�f)�f2)1/3(15)

where μ_f is the fluid dynamic viscosity.

In Equation (14), the entrainment parameter α_i confirms the rate at which sediment erodes when the given shear stress is larger than the critical shear stress, and the recommended value 0.018 was adopted according to the experimental data of Mastbergen and Von den Berg [43]. n_s is the outward pointing normal to the seabed interface, and n_s = (0,0,1) according to the Cartesian coordinates used in present numerical model.

The shields parameter was obtained from the following equation:

θ=U2f,m(ρi/ρf−1)gd50�=�f,m2(��/�f−1)��50(16)

where, U_f,m is the maximum value of the near-bed friction velocity; d₅₀ is the median diameter of sand particles. The detailed calculation procedure of θ was available in Soulsby [44].

The critical shields parameter θ_cr was obtained from the Equation (17) [44]

θcr=0.31+1.2d∗+0.055[1−exp(−0.02d∗)]�cr=0.31+1.2�*+0.0551−exp(−0.02�*)(17)

The sand particles begin to deposit on seabed when the turbulence energy weaken and cann’t support the particles suspending. The setting velocity of the particles was calculated from the following equation [44]:

usettling,i=νfdi[(10.362+1.049d3∗)0.5−10.36]�settling,�=�f��(10.362+1.049�*3)0.5−10.36(18)

where ν_f is the fluid kinematic viscosity.

2.3.2. Bed Load Transport

This is called bed load transport when the sand particles roll or bounce over the seabed and always have contact with seabed. The bed load transport velocity was computed by [45]:

ubedload,i=qb,iδicb,ifb�bedload,�=�b,��b,��b(19)

where, q_b,i is the bed load transport rate, which was obtained from Equation (20), δ_i is the bed load thickness, which was calculated by Equation (21), c_b,i is the volume fraction of sand i in the multiple species, f_b is the critical packing fraction of the seabed.

qb,i=8[∥g∥(ρi−ρfρf)d3i]1/2�b,�=8�(��−�f�f)��31/2(20)

δi=0.3d0.7∗(θθcr−1)0.5di��=0.3�*0.7(��cr−1)0.5��(21)

2.3.3. Suspended Load Transport

Through the following transport equation, the suspended sediment concentration could be acquired.

∂Cs,i∂t+∇(us,iCs,i)=∇∇(DfCs,i)∂�s,�∂�+∇(�s,��s,�)=∇∇(�f�s,�)(22)

where, C_s,i is the suspended sand particles mass concentration of sand i in the multiple species, u_s,i is the sand particles velocity of sand i, D_f is the diffusivity.

The velocity of sand i in the multiple species could be obtained from the following equation:

us,i=u¯¯+usettling,ics,i�s,�=�¯+�settling,��s,�(23)

where, u¯�¯ is the velocity of mixed fluid-particles, which can be calculated by the RANS equation with turbulence model, c_s,i is the suspended sand particles volume concentration, which was computed from Equation (24).

cs,i=Cs,iρi�s,�=�s,��(24)

3. Model Setup

The seabed-USAF-wave three-dimensional scour numerical model was built using Flow-3D software. As shown in Figure 2, the model includes sandy seabed, USAF model, sea water, two baffles and porous media. The dimensions of USAF are shown in Table 1. The sandy bed (210 m in length, 30 m in width and 11 m in height) is made up of uniform fine sand with median diameter d₅₀ = 0.041 cm. The USAF model includes upper steel tube with the length of 20 m, which was installed in the middle of seabed. The location of USAF is positioned at 140 m from the upstream inflow boundary and 70 m from the downstream outflow boundary. Two baffles were installed at two ends of seabed. In order to eliminate the wave reflection basically, the porous media was set at the outflow side on the seabed.

Figure 2. (a) The sketch of seabed-USAF-wave three-dimensional model; (b) boundary condation:Wv-wave boundary, S-symmetric boundary, O-outflow boundary; (c) USAF model.

Table 1. Numerical simulating cases.

3.1. Mesh Geometric Dimensions

In the simulation of the scour under the random waves, the model includes the umbrella suction anchor foundation, seabed and fluid. As shown in Figure 3, the model mesh includes global mesh grid and nested mesh grid, and the total number of grids is 1,812,000. The basic procedure for building mesh grid consists of two steps. Step 1: Divide the global mesh using regular hexahedron with size of 0.6 × 0.6. The global mesh area is cubic box, embracing the seabed and whole fluid volume, and the dimensions are 210 m in length, 30 m in width and 32 m in height. The details of determining the grid size can see the following mesh sensitivity section. Step 2: Set nested fine mesh grid in vicinity of the USAF with size of 0.3 × 0.3 so as to shorten the computation cost and improve the calculation accuracy. The encryption range is −15 m to 15 m in x direction, −15 m to 15 m in y direction and 0 m to 32 m in z direction, respectively. In order to accurately capture the free-surface dynamics, such as the fluid-air interface, the volume of fluid (VOF) method was adopted for tracking the free water surface. One specific algorithm called FAVORTM (Fractional Area/Volume Obstacle Representation) was used to define the fractional face areas and fractional volumes of the cells which are open to fluid flow.

Figure 3. The sketch of mesh grid.

3.2. Boundary Conditions

As shown in Figure 2, the initial fluid length is 210 m as long as seabed. A wave boundary was specified at the upstream offshore end. The details of determining the random wave spectrum can see the following wave parameters section. The outflow boundary was set at the downstream onshore end. The symmetry boundary was used at the top and two sides of the model. The symmetric boundaries were the better strategy to improve the computation efficiency and save the calculation cost [46]. At the seabed bottom, the wall boundary was adopted, which means the u = v = w= 0. Besides, the upper steel tube of USAF was set as no-slip condition.

3.3. Wave Parameters

The random waves with JONSWAP wave spectrum were used for all simulations as realistic representation of offshore conditions. The unidirectional JONSWAP frequency spectrum was described as [47]:

S(ω)=αg2ω5exp[−54(ωpω)4]γexp[−(ω−ωp)22σ2ω2p]�(�)=��2�5exp−54(�p�)4�exp−(�−�p)22�2�p2(25)

where, α is wave energy scale parameter, which is calculated by Equation (26), ω is frequency, ω_p is wave spectrum peak frequency, which can be obtained from Equation (27). γ is wave spectrum peak enhancement factor, in this study γ = 3.3. σ is spectral width factor, σ equals 0.07 for ω ≤ ω_p and 0.09 for ω > ω_p respectively.

α=0.0076(gXU2)−0.22�=0.0076(��2)−0.22(26)

ωp=22(gU)(gXU2)−0.33�p=22(��)(��2)−0.33(27)

where, X is fetch length, U is average wind velocity at 10 m height from mean sea level.

In present numerical model, the input key parameters include X and U for wave boundary with JONSWAP wave spectrum. The objective wave height and period are available by different combinations of X and U. In this study, we designed 9 cases with different wave heights, periods and water depths for simulating scour around USAF under random waves (see Table 2). For random waves, the wave steepness ε and Ursell number U_r were acquired form Equations (28) and (29) respectively

ε=2πgHsT2a�=2��s�a2(28)

Ur=Hsk2h3w�r=�s�2ℎw3(29)

where, H_s is significant wave height, T_a is average wave period, k is wave number, h_w is water depth. The Shield parameter θ satisfies θ _> θ_cr for all simulations in current study, indicating the live bed scour prevails.

Table 2. Numerical simulating cases.

3.4. Mesh Sensitivity

In this section, a mesh sensitivity analysis was conducted to investigate the influence of mesh grid size to results and make sure the calculation is mesh size independent and converged. Three mesh grid size were chosen: Mesh 1—global mesh grid size of 0.75 × 0.75, nested fine mesh grid size of 0.4 × 0.4, and total number of grids 1,724,000, Mesh 2—global mesh grid size of 0.6 × 0.6, nested fine mesh grid size of 0.3 × 0.3, and total number of grids 1,812,000, Mesh 3—global mesh grid size of 0.4 × 0.4, nested fine mesh grid size of 0.2 × 0.2, and total number of grids 1,932,000. The near-bed shear velocity U_* is an important factor for influencing scour process [1,15], so U_* at the position of (4,0,11.12) was evaluated under three mesh sizes. As the Figure 4 shown, the maximum error of shear velocity ∆U_*1,2 is about 39.8% between the mesh 1 and mesh 2, and 4.8% between the mesh 2 and mesh 3. According to the mesh sensitivity criterion adopted by Pang et al. [48], it’s reasonable to think the results are mesh size independent and converged with mesh 2. Additionally, the present model was built according to prototype size, and the mesh size used in present model is larger than the mesh size adopted by Higueira et al. [49] and Corvaro et al. [50]. If we choose the smallest cell size, it will take too much time. For example, the simulation with Mesh3 required about 260 h by using a computer with Intel Xeon Scalable Gold 4214 CPU @24 Cores, 2.2 GHz and 64.00 GB RAM. Therefore, in this case, considering calculation accuracy and computation efficiency, the mesh 2 was chosen for all the simulation in this study.

Figure 4. Comparison of near-bed shear velocity U_* with different mesh grid size.

The nested mesh block was adopted for seabed in vicinity of the USAF, which was overlapped with the global mesh block. When two mesh blocks overlap each other, the governing equations are by default solved on the mesh block with smaller average cell size (i.e., higher grid resolution). It is should be noted that the Flow 3D software used the moving mesh captures the scour evolution and automatically adjusts the time step size to be as large as possible without exceeding any of the stability limits, affecting accuracy, or unduly increasing the effort required to enforce the continuity condition [51].

3.5. Model Validation

In order to verify the reliability of the present model, the results of present study were compared with the experimental data of Khosronejad et al. [52]. The experiment was conducted in an open channel with a slender vertical pile under unidirectional currents. The comparison of scour development between the present results and the experimental results is shown in Figure 5. The Figure 5 reveals that the present results agree well with the experimental data of Khosronejad et al. [52]. In the first stage, the scour depth increases rapidly. After that, the scour depth achieves a maximum value gradually. The equilibrium scour depth calculated by the present model is basically corresponding with the experimental results of Khosronejad et al. [52], although scour depth in the present model is slightly larger than the experimental results at initial stage.

Figure 5. Comparison of time evolution of scour between the present study and Khosronejad et al. [52], Petersen et al. [17].

Secondly, another comparison was further conducted between the results of present study and the experimental data of Petersen et al. [17]. The experiment was carried out in a flume with a circular vertical pile in combined waves and current. Figure 4 shows a comparison of time evolution of scour depth between the simulating and the experimental results. As Figure 5 indicates, the scour depth in this study has good overall agreement with the experimental results proposed in Petersen et al. [17]. The equilibrium scour depth calculated by the present model is 0.399 m, which equals to the experimental value basically. Overall, the above verifications prove the present model is accurate and capable in dealing with sediment scour under waves.

In addition, in order to calibrate and validate the present model for hydrodynamic parameters, the comparison of water surface elevation was carried out with laboratory experiments conducted by Stahlmann [53] for wave gauge No. 3. The Figure 6 depicts the surface wave profiles between experiments and numerical model results. The comparison indicates that there is a good agreement between the model results and experimental values, especially the locations of wave crest and trough. Comparison of the surface elevation instructs the present model has an acceptable relative error, and the model is a calibrated in terms of the hydrodynamic parameters.

Figure 6. Comparison of surface elevation between the present study and Stahlmann [53].

Finally, another comparison was conducted for equilibrium scour depth or maximum scour depth under random waves with the experimental data of Sumer and Fredsøe [16] and Schendel et al. [22]. The Figure 7 shows the comparison between the numerical results and experimental data of Run01, Run05, Run21 and Run22 in Sumer and Fredsøe [16] and test A05 and A09 in Schendel et al. [22]. As shown in Figure 7, the equilibrium scour depth or maximum scour depth distributed within the ±30 error lines basically, meaning the reliability and accuracy of present model for predicting equilibrium scour depth around foundation in random waves. However, compared with the experimental values, the present model overestimated the equilibrium scour depth generally. Given that, a calibration for scour depth was carried out by multiplying the mean reduced coefficient 0.85 in following section.

Figure 7. Comparison of equilibrium (or maximum) scour depth between the present study and Sumer and Fredsøe [16], Schendel et al. [22].

Through the various examination for hydrodynamic and morphology parameters, it can be concluded that the present model is a validated and calibrated model for scour under random waves. Thus, the present numerical model would be utilized for scour simulation around foundation under random waves.

4. Numerical Results and Discussions

4.1. Scour Evolution

Figure 8 displays the scour evolution for case 1–9. As shown in Figure 8a, the scour depth increased rapidly at the initial stage, and then slowed down at the transition stage, which attributes to the backfilling occurred in scour holes under live bed scour condition, resulting in the net scour decreasing. Finally, the scour reached the equilibrium state when the amount of sediment backfilling equaled to that of scouring in the scour holes, i.e., the net scour transport rate was nil. Sumer and Fredsøe [16] proposed the following formula for the scour development under waves

St=Seq(1−exp(−t/Tc))�t=�eq(1−exp(−�/�c))(30)

where T_c is time scale of scour process.

Figure 8. Time evolution of scour for case 1–9: (a) Case 1–5; (b) Case 6–9.

The computing time is 3600 s and the scour development curves in Figure 8 kept fluctuating, meaning it’s still not in equilibrium scour stage in these cases. According to Sumer and Fredsøe [16], the equilibrium scour depth can be acquired by fitting the data with Equation (30). From Figure 8, it can be seen that the scour evolution obtained from Equation (30) is consistent with the present study basically at initial stage, but the scour depth predicted by Equation (30) developed slightly faster than the simulating results and the Equation (30) overestimated the scour depth to some extent. Overall, the whole tendency of the results calculated by Equation (30) agrees well with the simulating results of the present study, which means the Equation (30) is applicable to depict the scour evolution around USAF under random waves.

4.2. Scour Mechanism under Random Waves

The scour morphology and scour evolution around USAF are similar under random waves in case 1~9. Taking case 7 as an example, the scour morphology is shown in Figure 9.

Figure 9. Scour morphology under different times for case 7.

From Figure 9, at the initial stage (t < 1200 s), the scour occurred at upstream foundation edges between neighboring anchor branches. The maximum scour depth appeared at the lee-side of the USAF. Correspondingly, the sediments deposited at the periphery of the USAF, and the location of the maximum accretion depth was positioned at an angle of about 45° symmetrically with respect to the wave propagating direction in the lee-side of the USAF. After that, when t > 2400 s, the location of the maximum scour depth shifted to the upside of the USAF at an angle of about 45° with respect to the wave propagating direction.

According to previous studies [1,15,16,19,30,31], the horseshoe vortex, streamline compression and wake vortex shedding were responsible for scour around foundation. The Figure 10 displays the distribution of flow velocity in vicinity of foundation, which reflects the evolving processes of horseshoe vertex.

Figure 10. Velocity profile around USAF: (a) Flow runup and down stream at upstream anchor edges; (b) Horseshoe vortex at upstream anchor edges; (c) Flow reversal during wave through stage at lee side.

As shown in Figure 10, the inflow tripped to the upstream edges of the USAF and it was blocked by the upper tube of USAF. Then, the downflow formed the horizontal axis clockwise vortex and rolled on the seabed bypassing the tube, that is, the horseshoe vortex (Figure 11). The Figure 12 displays the turbulence intensity around the tube on the seabed. From Figure 12, it can be seen that the turbulence intensity was high-intensity with respect to the region of horseshoe vortex. This phenomenon occurred because of drastic water flow momentum exchanging in the horseshoe vortex. As a result, it created the prominent shear stress on the seabed, causing the local scour at the upstream edges of USAF. Besides, the horseshoe vortex moved downstream gradually along the periphery of the tube and the wake vortex shed off continually at the lee-side of the USAF, i.e., wake vortex.

Figure 11. Sketch of scour mechanism around USAF under random waves.

Figure 12. Turbulence intensity: (a) Turbulence intensity of horseshoe vortex; (b) Turbulence intensity of wake vortex; (c) Turbulence intensity of accretion area.

The core of wake vortex is a negative pressure center, liking a vacuum cleaner [11,42]. Hence, the soil particles were swirled into the negative pressure core and carried away by wake vortex. At the same time, the onset of scour at rear side occurred. Finally, the wake vortex became downflow at the downside of USAF. As is shown in Figure 12, the turbulence intensity was low where the downflow occurred at lee-side, which means the turbulence energy may not be able to support the survival of wake vortex, leading to accretion happening. As mentioned in previous section, the formation of horseshoe vortex was dependent with adverse pressure gradient at upside of foundation. As shown in Figure 13, the evaluated range of pressure distribution is −15 m to 15 m in x direction. The t = 450 s and t = 1800 s indicate that the wave crest and trough arrived at the upside and lee-side of the foundation respectively, and the t = 350 s was neither the wave crest nor trough. The adverse gradient pressure reached the maximum value at t = 450 s corresponding to the wave crest phase. In this case, it’s helpful for the wave boundary separating fully from seabed, which leads to the formation of horseshoe vortex with high turbulence intensity. Therefore, the horseshoe vortex is responsible for the local scour between neighboring anchor branches at upside of USAF. What’s more, due to the combination of the horseshoe vortex and streamline compression, the maximum scour depth occurred at the upside of the USAF with an angle of about 45° corresponding to the wave propagating direction. This is consistent with the findings of Pang et al. [48] and Sumer et al. [1,15] in case of regular waves. At the wave trough phase (t = 1800 s), the pressure gradient became positive at upstream USAF edges, which hindered the separating of wave boundary from seabed. In the meantime, the flow reversal occurred (Figure 10) and the adverse gradient pressure appeared at downstream USAF edges, but the magnitude of adverse gradient pressure at lee-side was lower than the upstream gradient pressure under wave crest. In this way, the intensity of horseshoe vortex behind the USAF under wave trough was low, which explains the difference of scour depth at upstream and downstream, i.e., the scour asymmetry. In other words, the scour asymmetry at upside and downside of USAF was attributed to wave asymmetry for random waves, and the phenomenon became more evident for nonlinear waves [21]. Briefly speaking, the vortex system at wave crest phase was mainly related to the scour process around USAF under random waves.

Figure 13. Pressure distribution around USAF.

4.3. Equilibrium Scour Depth

The KC number is a key parameter for horseshoe vortex emerging and evolving under waves. According to Equation (1), when pile diameter D is fixed, the KC depends on the maximum near-bed velocity U_wm and wave period T. For random waves, the U_wm can be denoted by the root-mean-square (RMS) value of near-bed velocity amplitude U_wm,rms or the significant value of near-bed velocity amplitude U_wm,s. The U_wm,rms and U_wm,s for all simulating cases of the present study are listed in Table 3 and Table 4. The T can be denoted by the mean up zero-crossing wave period T_a, peak wave period T_p, significant wave period T_s, the maximum wave period T_m, 1/10′th highest wave period T_{n = 1/10} and 1/5′th highest wave period T_{n = 1/5} for random waves, so the different combinations of U_wm and T will acquire different KC. The Table 3 and Table 4 list 12 types of KC, for example, the KC_rms,s was calculated by U_wm,rms and T_s. Sumer and Fredsøe [16] conducted a series of wave flume experiments to investigate the scour depth around monopile under random waves, and found the equilibrium scour depth predicting equation (Equation (2)) for regular waves was applicable for random waves with KC_rms,p. It should be noted that the Equation (2) is only suitable for KC > 6 under regular waves or KC_rms,p > 6 under random waves.

Table 3. U_wm,rms and KC for case 1~9.

Table 4. U_wm,s and KC for case 1~9.

Raaijmakers and Rudolph [34] proposed the equilibrium scour depth predicting model (Equation (5)) around pile under waves, which is suitable for low KC. The format of Equation (5) is similar with the formula proposed by Breusers [54], which can predict the equilibrium scour depth around pile at different scour stages. In order to verify the applicability of Raaijmakers’s model for predicting the equilibrium scour depth around USAF under random waves, a validation of the equilibrium scour depth S_eq between the present study and Raaijmakers’s equation was conducted. The position where the scour depth S_eq was evaluated is the location of the maximum scour depth, and it was depicted in Figure 14. The Figure 15 displays the comparison of S_eq with different KC between the present study and Raaijmakers’s model.

Figure 14. Sketch of the position where the S_eq was evaluated.

Figure 15. Comparison of the equilibrium scour depth between the present model and the model of Raaijmakers and Rudolph [34]: (a) KC_rms,s, KC_rms,a; (b) KC_rms,p, KC_rms,m; (c) KC_{rms,n = 1/10}, KC_{rms,n = 1/5}; (d) KC_s,s, KC_s,a; (e) KC_s,p, KC_s,m; (f) KC_{s,n = 1/10}, KC_{s,n = 1/5}.

As shown in Figure 15, there is an error in predicting S_eq between the present study and Raaijmakers’s model, and Raaijmakers’s model underestimates the results generally. Although the error exists, the varying trend of S_eq with KC obtained from Raaijmakers’s model is consistent with the present study basically. What’s more, the error is minimum and the Raaijmakers’s model is of relatively high accuracy for predicting scour around USAF under random waves by using KC_s,p. Based on this, a further revision was made to eliminate the error as much as possible, i.e., add the deviation value ∆S/D in the Raaijmakers’s model. The revised equilibrium scour depth predicting equation based on Raaijmakers’s model can be written as

S′eq/D=1.95[tanh(hD)](1−exp(−0.012KCs,p))+ΔS/D�eq′/�=1.95tanh(ℎ�)(1−exp(−0.012��s,p))+∆�/�(31)

As the Figure 16 shown, through trial-calculation, when ∆S/D = 0.05, the results calculated by Equation (31) show good agreement with the simulating results of the present study. The maximum error is about 18.2% and the engineering requirements have been met basically. In order to further verify the accuracy of the revised model for large KC (KC_s,p > 4) under random waves, a validation between the revised model and the previous experimental results [21]. The experiment was conducted in a flume (50 m in length, 1.0 m in width and 1.3 m in height) with a slender vertical pile (D = 0.1 m) under random waves. The seabed is composed of 0.13 m deep layer of sand with d₅₀ = 0.6 mm and the water depth is 0.5 m for all tests. The significant wave height is 0.12~0.21 m and the KC_s,p is 5.52~11.38. The comparison between the predicting results by Equation (31) and the experimental results of Corvaro et al. [21] is shown in Figure 17. From Figure 17, the experimental data evenly distributes around the predicted results and the prediction accuracy is favorable when KC_s,p < 8. However, the gap between the predicting results and experimental data becomes large and the Equation (31) overestimates the equilibrium scour depth to some extent when KC_s,p > 8.

Figure 16. Comparison of S_eq between the simulating results and the predicting values by Equation (31).

Figure 17. Comparison of S_eq/D between the Experimental results of Corvaro et al. [21] and the predicting values by Equation (31).

In ocean environment, the waves are composed of a train of sinusoidal waves with different frequencies and amplitudes. The energy of constituent waves with very large and very small frequencies is relatively low, and the energy of waves is mainly concentrated in a certain range of moderate frequencies. Myrhaug and Rue [37] thought the 1/n’th highest wave was responsible for scour and proposed the stochastic model to predict the equilibrium scour depth around pile under random waves for full range of KC. Noteworthy is that the KC was denoted by KC_rms,a in the stochastic model. To verify the application of the stochastic model for predicting scour depth around USAF, a validation between the simulating results of present study and predicting results by the stochastic model with n = 2,3,5,10,20,500 was carried out respectively.

As shown in Figure 18, compared with the simulating results, the stochastic model underestimates the equilibrium scour depth around USAF generally. Although the error exists, the varying trend of S_eq with KC_rms,a obtained from the stochastic model is consistent with the present study basically. What’s more, the gap between the predicting values by stochastic model and the simulating results decreases with the increase of n, but for large n, for example n = 500, the varying trend diverges between the predicting values and simulating results, meaning it’s not feasible only by increasing n in stochastic model to predict the equilibrium scour depth around USAF.

Figure 18. Comparison of S_eq between the simulating results and the predicting values by Equation (8).

The Figure 19 lists the deviation value ∆S_eq/D′ between the predicting values and simulating results with different KC_rms,a and n. Then, fitted the relationship between the ∆S′and n under different KC_rms,a, and the fitting curve can be written by Equation (32). The revised stochastic model (Equation (33)) can be acquired by adding ∆S_eq/D′ to Equation (8).

ΔSeq/D=0.052*exp(−n/6.566)+0.068∆�eq/�=0.052*exp(−�/6.566)+0.068(32)

S′eq¯/D=S′eq/D+0.052*exp(−n/6.566)+0.068�eq′¯/�=�eq′/�+0.052*exp(−�/6.566)+0.068(33)

Figure 19. The fitting line between ∆S′and n.

The comparison between the predicting results by Equation (33) and the simulating results of present study is shown in Figure 20. According to the Figure 20, the varying trend of S_eq with KC_rms,a obtained from the stochastic model is consistent with the present study basically. Compared with predicting results by the stochastic model, the results calculated by Equation (33) is favorable. Moreover, comparison with simulating results indicates that the predicting results are the most favorable for n = 10, which is consistent with the findings of Myrhaug and Rue [37] for equilibrium scour depth predicting around slender pile in case of random waves.

Figure 20. Comparison of S_eq between the simulating results and the predicting values by Equation (33).

In order to further verify the accuracy of the Equation (33) for large KC (KC_rms,a > 4) under random waves, a validation was conducted between the Equation (33) and the previous experimental results of Sumer and Fredsøe [16] and Corvaro et al. [21]. The details of experiments conducted by Corvaro et al. [21] were described in above section. Sumer and Fredsøe [16] investigated the local scour around pile under random waves. The experiments were conducted in a wave basin with a slender vertical pile (D = 0.032, 0.055 m). The seabed is composed of 0.14 m deep layer of sand with d₅₀ = 0.2 mm and the water depth was maintained at 0.5 m. The JONSWAP wave spectrum was used and the KC_rms,a was 5.29~16.95. The comparison between the predicting results by Equation (33) and the experimental results of Sumer and Fredsøe [16] and Corvaro et al. [21] are shown in Figure 21. From Figure 21, contrary to the case of low KC_rms,a (KC_rms,a < 4), the error between the predicting values and experimental results increases with decreasing of n for KC_rms,a > 4. Therefore, the predicting results are the most favorable for n = 2 when KC_rms,a > 4.

Figure 21. Comparison of S_eq between the experimental results of Sumer and Fredsøe [16] and Corvaro et al. [21] and the predicting values by Equation (33).

Noteworthy is that the present model was built according to prototype size, so the errors between the numerical results and experimental data of References [16,21] may be attribute to the scale effects. In laboratory experiments on scouring process, it is typically impossible to ensure a rigorous similarity of all physical parameters between the model and prototype structure, leading to the scale effects in the laboratory experiments. To avoid a cohesive behaviour, the bed material was not scaled geometrically according to model scale. As a consequence, the relatively large-scaled sediments sizes may result in the overestimation of bed load transport and underestimation of suspended load transport compared with field conditions. What’s more, the disproportional scaled sediment presumably lead to the difference of bed roughness between the model and prototype, and thus large influences for wave boundary layer on the seabed and scour process. Besides, according to Corvaro et al. [21] and Schendel et al. [55], the pile Reynolds numbers and Froude numbers both affect the scour depth for the condition of non fully developed turbulent flow in laboratory experiments.

4.4. Parametric Study

4.4.1. Influence of Froude Number

As described above, the set of foundation leads to the adverse pressure gradient appearing at upstream, leading to the wave boundary layer separating from seabed, then horseshoe vortex formatting and the horseshoe vortex are mainly responsible for scour around foundation (see Figure 22). The Froude number F_r is the key parameter to influence the scale and intensity of horseshoe vortex. The F_r under waves can be calculated by the following formula [42]

Fr=UwgD−−−√�r=�w��(34)

where U_w is the mean water particle velocity during 1/4 cycle of wave oscillation, obtained from the following formula. Noteworthy is that the root-mean-square (RMS) value of near-bed velocity amplitude U_wm,rms is used for calculating U_wm.

Uw=1T/4∫0T/4Uwmsin(t/T)dt=2πUwm�w=1�/4∫0�/4�wmsin(�/�)��=2��wm(35)

Figure 22. Sketch of flow field at upstream USAF edges.

Tavouktsoglou et al. [25] proposed the following formula between F_r and the vertical location of the stagnation y

yh∝Fer�ℎ∝�r�(36)

where e is constant.

The Figure 23 displays the relationship between S_eq/D and F_r of the present study. In order to compare with the simulating results, the experimental data of Corvaro et al. [21] was also depicted in Figure 23. As shown in Figure 23, the equilibrium scour depth appears a logarithmic increase as F_r increases and approaches the mathematical asymptotic value, which is also consistent with the experimental results of Corvaro et al. [21]. According to Figure 24, the adverse pressure gradient pressure at upstream USAF edges increases with the increase of F_r, which is benefit for the wave boundary layer separating from seabed, resulting in the high-intensity horseshoe vortex, hence, causing intensive scour around USAF. Based on the previous study of Tavouktsoglou et al. [25] for scour around pile under currents, the high F_r leads to the stagnation point is closer to the mean sea level for shallow water, causing the stronger downflow kinetic energy. As mentioned in previous section, the energy of downflow at upstream makes up the energy of the subsequent horseshoe vortex, so the stronger downflow kinetic energy results in the more intensive horseshoe vortex. Therefore, the higher F_r leads to the more intensive horseshoe vortex by influencing the position of stagnation point y presumably. Qi and Gao [19] carried out a series of flume tests to investigate the scour around pile under regular waves, and proposed the fitting formula between S_eq/D and F_r as following

lg(Seq/D)=Aexp(B/Fr)+Clg(�eq/�)=�exp(�/�r)+�(37)

where A, B and C are constant.

Figure 23. The fitting curve between S_eq/D and F_r.

Figure 24. Sketch of adverse pressure gradient at upstream USAF edges.

Took the Equation (37) to fit the simulating results with A = −0.002, B = 0.686 and C = −0.808, and the results are shown in Figure 23. From Figure 23, the simulating results evenly distribute around the Equation (37) and the varying trend of S_eq/D and F_r in present study is consistent with Equation (37) basically, meaning the Equation (37) is applicable to express the relationship of S_eq/D with F_r around USAF under random waves.

4.4.2. Influence of Euler Number

The Euler number E_u is the influencing factor for the hydrodynamic field around foundation. The E_u under waves can be calculated by the following formula. The E_u can be represented by the Equation (38) for uniform cylinders [25]. The root-mean-square (RMS) value of near-bed velocity amplitude U_m,rms is used for calculating U_m.

Eu=U2mgD�u=�m2��(38)

where U_m is depth-averaged flow velocity.

The Figure 25 displays the relationship between S_eq/D and E_u of the present study. In order to compare with the simulating results, the experimental data of Sumer and Fredsøe [16] and Corvaro et al. [21] were also plotted in Figure 25. As shown in Figure 25, similar with the varying trend of S_eq/D and F_r, the equilibrium scour depth appears a logarithmic increase as E_u increases and approaches the mathematical asymptotic value, which is also consistent with the experimental results of Sumer and Fredsøe [16] and Corvaro et al. [21]. According to Figure 24, the adverse pressure gradient pressure at upstream USAF edges increases with the increasing of E_u, which is benefit for the wave boundary layer separating from seabed, inducing the high-intensity horseshoe vortex, hence, causing intensive scour around USAF.

Figure 25. The fitting curve between S_eq/D and E_u.

Therefore, the variation of F_r and E_u reflect the magnitude of adverse pressure gradient pressure at upstream. Given that, the Equation (37) also was used to fit the simulating results with A = 8.875, B = 0.078 and C = −9.601, and the results are shown in Figure 25. From Figure 25, the simulating results evenly distribute around the Equation (37) and the varying trend of S_eq/D and E_u in present study is consistent with Equation (37) basically, meaning the Equation (37) is also applicable to express the relationship of S_eq/D with E_u around USAF under random waves. Additionally, according to the above description of F_r, it can be inferred that the higher F_r and E_u both lead to the more intensive horseshoe vortex by influencing the position of stagnation point y presumably.

5. Conclusions

A series of numerical models were established to investigate the local scour around umbrella suction anchor foundation (USAF) under random waves. The numerical model was validated for hydrodynamic and morphology parameters by comparing with the experimental data of Khosronejad et al. [52], Petersen et al. [17], Sumer and Fredsøe [16] and Schendel et al. [22]. Based on the simulating results, the scour evolution and scour mechanisms around USAF under random waves were analyzed respectively. Two revised models were proposed according to the model of Raaijmakers and Rudolph [34] and the stochastic model developed by Myrhaug and Rue [37] to predict the equilibrium scour depth around USAF under random waves. Finally, a parametric study was carried out with the present model to study the effects of the Froude number F_r and Euler number E_u to the equilibrium scour depth around USAF under random waves. The main conclusions can be described as follows.(1)

The packed sediment scour model and the RNG k−ε turbulence model were used to simulate the sand particles transport processes and the flow field around UASF respectively. The scour evolution obtained by the present model agrees well with the experimental results of Khosronejad et al. [52], Petersen et al. [17], Sumer and Fredsøe [16] and Schendel et al. [22], which indicates that the present model is accurate and reasonable for depicting the scour morphology around UASF under random waves.(2)

The vortex system at wave crest phase is mainly related to the scour process around USAF under random waves. The maximum scour depth appeared at the lee-side of the USAF at the initial stage (t < 1200 s). Subsequently, when t > 2400 s, the location of the maximum scour depth shifted to the upside of the USAF at an angle of about 45° with respect to the wave propagating direction.(3)

The error is negligible and the Raaijmakers’s model is of relatively high accuracy for predicting scour around USAF under random waves when KC is calculated by KC_s,p. Given that, a further revision model (Equation (31)) was proposed according to Raaijmakers’s model to predict the equilibrium scour depth around USAF under random waves and it shows good agreement with the simulating results of the present study when KC_s,p < 8.(4)

Another further revision model (Equation (33)) was proposed according to the stochastic model established by Myrhaug and Rue [37] to predict the equilibrium scour depth around USAF under random waves, and the predicting results are the most favorable for n = 10 when KC_rms,a < 4. However, contrary to the case of low KC_rms,a, the predicting results are the most favorable for n = 2 when KC_rms,a > 4 by the comparison with experimental results of Sumer and Fredsøe [16] and Corvaro et al. [21].(5)

The same formula (Equation (37)) is applicable to express the relationship of S_eq/D with E_u or F_r, and it can be inferred that the higher F_r and E_u both lead to the more intensive horseshoe vortex and larger S_eq.

Author Contributions

Conceptualization, H.L. (Hongjun Liu); Data curation, R.H. and P.Y.; Formal analysis, X.W. and H.L. (Hao Leng); Funding acquisition, X.W.; Writing—original draft, R.H. and P.Y.; Writing—review & editing, X.W. and H.L. (Hao Leng); The final manuscript has been approved by all the authors. All authors have read and agreed to the published version of the manuscript.

Funding

This research was funded by the Fundamental Research Funds for the Central Universities (grant number 202061027) and the National Natural Science Foundation of China (grant number 41572247).

Institutional Review Board Statement

Not applicable.

Informed Consent Statement

Not applicable.

Data Availability Statement

The data presented in this study are available on request from the corresponding author.

Conflicts of Interest

The authors declare no conflict of interest.

References

Sumer, B.M.; Fredsøe, J.; Christiansen, N. Scour Around Vertical Pile in Waves. J. Waterw. Port. Coast. Ocean Eng. 1992, 118, 15–31. [Google Scholar] [CrossRef]
Rudolph, D.; Bos, K. Scour around a monopile under combined wave-current conditions and low KC-numbers. In Proceedings of the 6th International Conference on Scour and Erosion, Amsterdam, The Netherlands, 1–3 November 2006; pp. 582–588. [Google Scholar]
Nielsen, A.W.; Liu, X.; Sumer, B.M.; Fredsøe, J. Flow and bed shear stresses in scour protections around a pile in a current. Coast. Eng. 2013, 72, 20–38. [Google Scholar] [CrossRef]
Ahmad, N.; Bihs, H.; Myrhaug, D.; Kamath, A.; Arntsen, Ø.A. Three-dimensional numerical modelling of wave-induced scour around piles in a side-by-side arrangement. Coast. Eng. 2018, 138, 132–151. [Google Scholar] [CrossRef]
Li, H.; Ong, M.C.; Leira, B.J.; Myrhaug, D. Effects of Soil Profile Variation and Scour on Structural Response of an Offshore Monopile Wind Turbine. J. Offshore Mech. Arct. Eng. 2018, 140, 042001. [Google Scholar] [CrossRef]
Li, H.; Liu, H.; Liu, S. Dynamic analysis of umbrella suction anchor foundation embedded in seabed for offshore wind turbines. Géoméch. Energy Environ. 2017, 10, 12–20. [Google Scholar] [CrossRef]
Fazeres-Ferradosa, T.; Rosa-Santos, P.; Taveira-Pinto, F.; Vanem, E.; Carvalho, H.; Correia, J.A.F.D.O. Editorial: Advanced research on offshore structures and foundation design: Part 1. Proc. Inst. Civ. Eng. Marit. Eng. 2019, 172, 118–123. [Google Scholar] [CrossRef]
Chavez, C.E.A.; Stratigaki, V.; Wu, M.; Troch, P.; Schendel, A.; Welzel, M.; Villanueva, R.; Schlurmann, T.; De Vos, L.; Kisacik, D.; et al. Large-Scale Experiments to Improve Monopile Scour Protection Design Adapted to Climate Change—The PROTEUS Project. Energies 2019, 12, 1709. [Google Scholar] [CrossRef][Green Version]
Wu, M.; De Vos, L.; Chavez, C.E.A.; Stratigaki, V.; Fazeres-Ferradosa, T.; Rosa-Santos, P.; Taveira-Pinto, F.; Troch, P. Large Scale Experimental Study of the Scour Protection Damage Around a Monopile Foundation Under Combined Wave and Current Conditions. J. Mar. Sci. Eng. 2020, 8, 417. [Google Scholar] [CrossRef]
Sørensen, S.P.H.; Ibsen, L.B. Assessment of foundation design for offshore monopiles unprotected against scour. Ocean Eng. 2013, 63, 17–25. [Google Scholar] [CrossRef]
Prendergast, L.; Gavin, K.; Doherty, P. An investigation into the effect of scour on the natural frequency of an offshore wind turbine. Ocean Eng. 2015, 101, 1–11. [Google Scholar] [CrossRef][Green Version]
Fazeres-Ferradosa, T.; Chambel, J.; Taveira-Pinto, F.; Rosa-Santos, P.; Taveira-Pinto, F.; Giannini, G.; Haerens, P. Scour Protections for Offshore Foundations of Marine Energy Harvesting Technologies: A Review. J. Mar. Sci. Eng. 2021, 9, 297. [Google Scholar] [CrossRef]
Yang, Q.; Yu, P.; Liu, Y.; Liu, H.; Zhang, P.; Wang, Q. Scour characteristics of an offshore umbrella suction anchor foundation under the combined actions of waves and currents. Ocean Eng. 2020, 202, 106701. [Google Scholar] [CrossRef]
Yu, P.; Hu, R.; Yang, J.; Liu, H. Numerical investigation of local scour around USAF with different hydraulic conditions under currents and waves. Ocean Eng. 2020, 213, 107696. [Google Scholar] [CrossRef]
Sumer, B.M.; Christiansen, N.; Fredsøe, J. The horseshoe vortex and vortex shedding around a vertical wall-mounted cylinder exposed to waves. J. Fluid Mech. 1997, 332, 41–70. [Google Scholar] [CrossRef]
Sumer, B.M.; Fredsøe, J. Scour around Pile in Combined Waves and Current. J. Hydraul. Eng. 2001, 127, 403–411. [Google Scholar] [CrossRef]
Petersen, T.U.; Sumer, B.M.; Fredsøe, J. Time scale of scour around a pile in combined waves and current. In Proceedings of the 6th International Conference on Scour and Erosion, Paris, France, 27–31 August 2012. [Google Scholar]
Petersen, T.U.; Sumer, B.M.; Fredsøe, J.; Raaijmakers, T.C.; Schouten, J.-J. Edge scour at scour protections around piles in the marine environment—Laboratory and field investigation. Coast. Eng. 2015, 106, 42–72. [Google Scholar] [CrossRef]
Qi, W.; Gao, F. Equilibrium scour depth at offshore monopile foundation in combined waves and current. Sci. China Ser. E Technol. Sci. 2014, 57, 1030–1039. [Google Scholar] [CrossRef][Green Version]
Larsen, B.E.; Fuhrman, D.R.; Baykal, C.; Sumer, B.M. Tsunami-induced scour around monopile foundations. Coast. Eng. 2017, 129, 36–49. [Google Scholar] [CrossRef][Green Version]
Corvaro, S.; Marini, F.; Mancinelli, A.; Lorenzoni, C.; Brocchini, M. Hydro- and Morpho-dynamics Induced by a Vertical Slender Pile under Regular and Random Waves. J. Waterw. Port. Coast. Ocean Eng. 2018, 144, 04018018. [Google Scholar] [CrossRef]
Schendel, A.; Welzel, M.; Schlurmann, T.; Hsu, T.-W. Scour around a monopile induced by directionally spread irregular waves in combination with oblique currents. Coast. Eng. 2020, 161, 103751. [Google Scholar] [CrossRef]
Fazeres-Ferradosa, T.; Taveira-Pinto, F.; Romão, X.; Reis, M.; das Neves, L. Reliability assessment of offshore dynamic scour protections using copulas. Wind. Eng. 2018, 43, 506–538. [Google Scholar] [CrossRef]
Fazeres-Ferradosa, T.; Welzel, M.; Schendel, A.; Baelus, L.; Santos, P.R.; Pinto, F.T. Extended characterization of damage in rubble mound scour protections. Coast. Eng. 2020, 158, 103671. [Google Scholar] [CrossRef]
Tavouktsoglou, N.S.; Harris, J.M.; Simons, R.R.; Whitehouse, R.J.S. Equilibrium Scour-Depth Prediction around Cylindrical Structures. J. Waterw. Port. Coast. Ocean Eng. 2017, 143, 04017017. [Google Scholar] [CrossRef][Green Version]
Ettema, R.; Melville, B.; Barkdoll, B. Scale Effect in Pier-Scour Experiments. J. Hydraul. Eng. 1998, 124, 639–642. [Google Scholar] [CrossRef]
Umeda, S. Scour Regime and Scour Depth around a Pile in Waves. J. Coast. Res. Spec. Issue 2011, 64, 845–849. [Google Scholar]
Umeda, S. Scour process around monopiles during various phases of sea storms. J. Coast. Res. 2013, 165, 1599–1604. [Google Scholar] [CrossRef]
Baykal, C.; Sumer, B.; Fuhrman, D.R.; Jacobsen, N.; Fredsøe, J. Numerical simulation of scour and backfilling processes around a circular pile in waves. Coast. Eng. 2017, 122, 87–107. [Google Scholar] [CrossRef][Green Version]
Miles, J.; Martin, T.; Goddard, L. Current and wave effects around windfarm monopile foundations. Coast. Eng. 2017, 121, 167–178. [Google Scholar] [CrossRef][Green Version]
Miozzi, M.; Corvaro, S.; Pereira, F.A.; Brocchini, M. Wave-induced morphodynamics and sediment transport around a slender vertical cylinder. Adv. Water Resour. 2019, 129, 263–280. [Google Scholar] [CrossRef]
Yu, T.; Zhang, Y.; Zhang, S.; Shi, Z.; Chen, X.; Xu, Y.; Tang, Y. Experimental study on scour around a composite bucket foundation due to waves and current. Ocean Eng. 2019, 189, 106302. [Google Scholar] [CrossRef]
Carreiras, J.; Larroudé, P.; Seabra-Santos, F.; Mory, M. Wave Scour Around Piles. In Proceedings of the Coastal Engineering 2000, American Society of Civil Engineers (ASCE), Sydney, Australia, 16–21 July 2000; pp. 1860–1870. [Google Scholar]
Raaijmakers, T.; Rudolph, D. Time-dependent scour development under combined current and waves conditions—Laboratory experiments with online monitoring technique. In Proceedings of the 4th International Conference on Scour and Erosion, Tokyo, Japan, 5–7 November 2008; pp. 152–161. [Google Scholar]
Khalfin, I.S. Modeling and calculation of bed score around large-diameter vertical cylinder under wave action. Water Resour. 2007, 34, 357. [Google Scholar] [CrossRef][Green Version]
Zanke, U.C.; Hsu, T.-W.; Roland, A.; Link, O.; Diab, R. Equilibrium scour depths around piles in noncohesive sediments under currents and waves. Coast. Eng. 2011, 58, 986–991. [Google Scholar] [CrossRef]
Myrhaug, D.; Rue, H. Scour below pipelines and around vertical piles in random waves. Coast. Eng. 2003, 48, 227–242. [Google Scholar] [CrossRef]
Myrhaug, D.; Ong, M.C.; Føien, H.; Gjengedal, C.; Leira, B.J. Scour below pipelines and around vertical piles due to second-order random waves plus a current. Ocean Eng. 2009, 36, 605–616. [Google Scholar] [CrossRef]
Myrhaug, D.; Ong, M.C. Random wave-induced onshore scour characteristics around submerged breakwaters using a stochastic method. Ocean Eng. 2010, 37, 1233–1238. [Google Scholar] [CrossRef]
Ong, M.C.; Myrhaug, D.; Hesten, P. Scour around vertical piles due to long-crested and short-crested nonlinear random waves plus a current. Coast. Eng. 2013, 73, 106–114. [Google Scholar] [CrossRef]
Yakhot, V.; Orszag, S.A. Renormalization group analysis of turbulence. I. Basic theory. J. Sci. Comput. 1986, 1, 3–51. [Google Scholar] [CrossRef]
Yakhot, V.; Smith, L.M. The renormalization group, the e-expansion and derivation of turbulence models. J. Sci. Comput. 1992, 7, 35–61. [Google Scholar] [CrossRef]
Mastbergen, D.R.; Berg, J.V.D. Breaching in fine sands and the generation of sustained turbidity currents in submarine canyons. Sedimentology 2003, 50, 625–637. [Google Scholar] [CrossRef]
Soulsby, R. Dynamics of Marine Sands; Thomas Telford Ltd.: London, UK, 1998. [Google Scholar] [CrossRef]
Van Rijn, L.C. Sediment Transport, Part I: Bed Load Transport. J. Hydraul. Eng. 1984, 110, 1431–1456. [Google Scholar] [CrossRef][Green Version]
Zhang, Q.; Zhou, X.-L.; Wang, J.-H. Numerical investigation of local scour around three adjacent piles with different arrangements under current. Ocean Eng. 2017, 142, 625–638. [Google Scholar] [CrossRef]
Yu, Y.X.; Liu, S.X. Random Wave and Its Applications to Engineering, 4th ed.; Dalian University of Technology Press: Dalian, China, 2011. [Google Scholar]
Pang, A.; Skote, M.; Lim, S.; Gullman-Strand, J.; Morgan, N. A numerical approach for determining equilibrium scour depth around a mono-pile due to steady currents. Appl. Ocean Res. 2016, 57, 114–124. [Google Scholar] [CrossRef]
Higuera, P.; Lara, J.L.; Losada, I.J. Three-dimensional interaction of waves and porous coastal structures using Open-FOAM®. Part I: Formulation and validation. Coast. Eng. 2014, 83, 243–258. [Google Scholar] [CrossRef]
Corvaro, S.; Crivellini, A.; Marini, F.; Cimarelli, A.; Capitanelli, L.; Mancinelli, A. Experimental and Numerical Analysis of the Hydrodynamics around a Vertical Cylinder in Waves. J. Mar. Sci. Eng. 2019, 7, 453. [Google Scholar] [CrossRef][Green Version]
Flow3D User Manual, version 11.0.3; Flow Science, Inc.: Santa Fe, NM, USA, 2013.
Khosronejad, A.; Kang, S.; Sotiropoulos, F. Experimental and computational investigation of local scour around bridge piers. Adv. Water Resour. 2012, 37, 73–85. [Google Scholar] [CrossRef]
Stahlmann, A. Experimental and Numerical Modeling of Scour at Foundation Structures for Offshore Wind Turbines. Ph.D. Thesis, Franzius-Institute for Hydraulic, Estuarine and Coastal Engineering, Leibniz Universität Hannover, Hannover, Germany, 2013. [Google Scholar]
Breusers, H.N.C.; Nicollet, G.; Shen, H. Local Scour Around Cylindrical Piers. J. Hydraul. Res. 1977, 15, 211–252. [Google Scholar] [CrossRef]
Schendel, A.; Hildebrandt, A.; Goseberg, N.; Schlurmann, T. Processes and evolution of scour around a monopile induced by tidal currents. Coast. Eng. 2018, 139, 65–84. [Google Scholar] [CrossRef]

Publisher’s Note: MDPI stays neutral with regard to jurisdictional claims in published maps and institutional affiliations.

© 2021 by the authors. Licensee MDPI, Basel, Switzerland. This article is an open access article distributed under the terms and conditions of the Creative Commons Attribution (CC BY) license (https://creativecommons.org/licenses/by/4.0/).

Share and Cite

MDPI and ACS Style

Hu, R.; Liu, H.; Leng, H.; Yu, P.; Wang, X. Scour Characteristics and Equilibrium Scour Depth Prediction around Umbrella Suction Anchor Foundation under Random Waves. J. Mar. Sci. Eng. 2021, 9, 886. https://doi.org/10.3390/jmse9080886

AMA Style

Hu R, Liu H, Leng H, Yu P, Wang X. Scour Characteristics and Equilibrium Scour Depth Prediction around Umbrella Suction Anchor Foundation under Random Waves. Journal of Marine Science and Engineering. 2021; 9(8):886. https://doi.org/10.3390/jmse9080886Chicago/Turabian Style

Hu, Ruigeng, Hongjun Liu, Hao Leng, Peng Yu, and Xiuhai Wang. 2021. “Scour Characteristics and Equilibrium Scour Depth Prediction around Umbrella Suction Anchor Foundation under Random Waves” Journal of Marine Science and Engineering 9, no. 8: 886. https://doi.org/10.3390/jmse9080886

Find Other Styles

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

For more information on the journal statistics, click here.

Multiple requests from the same IP address are counted as one view.

원본 다운로드

레이저 보조 분말 기반 직접 에너지 증착에서 용융 풀 거동에 대한 감쇠 레이저 빔 강도 프로파일의 영향에 대한 열유체 모델링

Thermo-fluid modeling of influence of attenuated laser beam intensity profile on melt pool behavior in laser-assisted powder-based direct energy deposition

Mohammad Sattari, Amin Ebrahimi, Martin Luckabauer, Gert-willem R.B.E. Römer

Team Marcel Hermans

Research output: Chapter in Book/Conference proceedings/Edited volume › Conference contribution › Professional

5Downloads (Pure)

Abstract

A numerical framework based on computational fluid dynamics (CFD), using the finite volume method (FVM) and volume of fluid (VOF) technique is presented to investigate the effect of the laser beam intensity profile on melt pool behavior in laser-assisted powder-based directed energy deposition (L-DED). L-DED is an additive manufacturing (AM) process that utilizes a laser beam to fuse metal powder particles. To assure high-fidelity modeling, it was found that it is crucial to accurately model the interaction between the powder stream and the laser beam in the gas region above the substrate. The proposed model considers various phenomena including laser energy attenuation and absorption, multiple reflections of the laser rays, powder particle stream, particle-fluid interaction, temperature-dependent properties, buoyancy effects, thermal expansion, solidification shrinkage and drag, and Marangoni flow. The latter is induced by temperature and element-dependent surface tension. The model is validated using experimental results and highlights the importance of considering laser energy attenuation. Furthermore, the study investigates how the laser beam intensity profile affects melt pool size and shape, influencing the solidification microstructure and mechanical properties of the deposited material. The proposed model has the potential to optimize the L-DED process for a variety of materials and provides insights into the capability of numerical modeling for additive manufacturing optimization.

Original language	English
Title of host publication	Flow-3D World Users Conference
Publication status	Published – 2023
Event	Flow-3D World User Conference – Strasbourg, France Duration: 5 Jun 2023 → 7 Jun 2023

Conference

Conference	Flow-3D World User Conference
Country/Territory	France
City	Strasbourg
Period	5/06/23 → 7/06/23

What’s New – FLOW-3D 2023R2

FLOW-3D 소프트웨어 제품군의 모든 제품은 2023R1에서 IT 관련 개선 사항을 받았습니다. FLOW-3D 2023R1은 이제 Windows 11 및 RHEL 8을 지원합니다. 누락된 종속성을 보고하도록 Linux 설치 프로그램이 개선되었으며 더 이상 루트 수준 권한이 필요하지 않으므로 설치가 더 쉽고 안전해집니다. 또한 워크플로를 자동화한 사용자를 위해 입력 파일 변환기에 명령줄 인터페이스를 추가하여 스크립트 환경에서도 워크플로가 업데이트된 입력 파일로 작동하는지 확인할 수 있습니다.

확장된 PQ ² 분석

제조에 사용되는 유압 시스템은 PQ ² 곡선을 사용하여 모델링할 수 있습니다. 장치의 세부 사항을 건너뛰고 흐름에 미치는 영향을 포함하기 위해 질량-운동량 소스 또는 속도 경계 조건을 사용하여 유압 시스템을 근사화하는 것이 편리한 단순화인 경우가 많습니다. 기존 PQ ² 분석 모델을 확장하여 이러한 유형의 기하학적 단순화를 허용하면서도 여전히 현실적인 결과를 제공합니다. 이것은 시뮬레이션 시간과 모델 복잡성의 감소로 해석됩니다.

FLOW-3D 2022R2 의 새로운 기능

FLOW-3D 2022R2 제품군 의 출시와 함께 Flow Science는 워크스테이션과 FLOW-3D 의 HPC 버전 을 통합하여 단일 노드 CPU 구성에서 다중 구성에 이르기까지 모든 유형의 하드웨어 아키텍처를 활용할 수 있는 단일 솔버 엔진을 제공합니다. 노드 병렬 고성능 컴퓨팅 실행. 추가 개발에는 점탄성 흐름을 위한 새로운 로그 구조 텐서 방법, 지속적인 솔버 속도 성능 개선, 고급 냉각 채널 및 팬텀 구성 요소 제어, 향상된 연행 공기 기능이 포함됩니다.

통합 솔버

FLOW-3D 제품을 단일 통합 솔버로 마이그레이션하여 로컬 워크스테이션 또는 고성능 컴퓨팅 하드웨어 환경에서 원활하게 실행했습니다.

많은 사용자가 노트북이나 로컬 워크스테이션에서 모델을 실행하지만 고성능 컴퓨팅 클러스터에서 더 큰 모델을 실행합니다. 2022R2 릴리스에서는 통합 솔버를 통해 사용자가 HPC 솔루션에서 OpenMP/MPI 하이브리드 병렬화의 동일한 이점을 활용하여 워크스테이션 및 노트북에서 실행할 수 있습니다.

메쉬 분해의 예 — OpenMP/MPI 하이브리드 병렬화를 위한 메시 분해의 예

솔버 성능 개선

멀티 소켓 워크스테이션

멀티 소켓 워크스테이션은 이제 매우 일반적이며 대규모 시뮬레이션을 실행할 수 있습니다. 새로운 통합 솔버를 통해 이러한 유형의 하드웨어를 사용하는 사용자는 일반적으로 HPC 클러스터 구성에서만 사용할 수 있었던 OpenMP/MPI 하이브리드 병렬화를 활용하여 모델을 실행할 수 있는 성능 이점을 볼 수 있습니다.

낮은 수준의 루틴으로 벡터화 및 메모리 액세스 개선

대부분의 테스트 사례에서 10%에서 20% 정도의 성능 향상이 관찰되었으며 일부 사례에서는 20%를 초과하는 런타임 이점이 있었습니다.

정제된 체적 대류 안정성 한계

시간 단계 안정성 한계는 모델 런타임의 주요 동인입니다. 2022R2에서는 새로운 시간 단계 안정성 한계인 3D 대류 안정성 한계를 숫자 위젯에서 사용할 수 있습니다. 실행 중이고 대류가 제한된(cx, cy 또는 cz 제한) 모델의 경우 새 옵션은 30% 정도의 일반적인 속도 향상을 보여주었습니다.

압력 솔버 프리 컨디셔너

경우에 따라 까다로운 흐름 구성의 경우 과도한 압력 솔버 반복으로 인해 실행 시간이 길어질 수 있습니다. 어려운 경우 2022R2에서는 모델이 너무 많이 반복될 때 FLOW-3D가 자동으로 새로운 프리 컨디셔너를 활성화하여 압력 수렴을 돕습니다. 테스트의 런타임이 1.9배에서 335배까지 빨라졌습니다!

점탄성 유체에 대한 로그 형태 텐서 방법

점탄성 유체에 대한 새로운 솔버 옵션을 사용자가 사용할 수 있으며 특히 높은 Weissenberg 수치에 효과적입니다.

점탄성 흐름을 위한 개선된 솔루션 — 로그 구조 텐서 솔루션을 사용하여 점탄성 흐름에 대한 높은 Weissenberg 수에서 개선된 솔루션의 예. Courtesy MF Tome, et al., J. Non-Newton. 체액. 기계 175-176 (2012) 44–54

활성 시뮬레이션 제어 확장

능동 시뮬레이션 제어 기능은 연속 주조 및 적층 제조 응용 프로그램과 주조 및 기타 여러 열 관리 응용 프로그램에 사용되는 냉각 채널에 일반적으로 사용되는 팬텀 개체를 포함하도록 확장되었습니다.

가상 물체 속도 제어의 예 — 산업용 탱크 적용을 위한 동적 냉각 채널 제어의 예

연행 공기 기능 개선

디퓨저 및 유사한 산업용 기포 흐름 응용 분야의 경우 이제 대량 공급원을 사용하여 물 기둥에 공기를 도입할 수 있습니다. 또한 혼입 공기 및 용존 산소의 난류 확산에 대한 기본값이 업데이트되었으며 매우 낮은 공기 농도에 대한 모델 정확도가 향상되었습니다.

디퓨저 모델의 예: 질량원을 사용하여 물기둥에 공기를 도입할 수 있습니다.

Figure 14. Defects: (a) Unmelt defects(Scheme NO.4);(b) Pores defects(Scheme NO.1); (c); Spattering defect (Scheme NO.3); (d) Low overlapping rate defects(Scheme NO.5).

Molten pool structure, temperature and velocity
flow in selective laser melting AlCu5MnCdVA alloy

용융 풀 구조, 선택적 온도 및 속도 흐름 레이저 용융 AlCu5MnCdVA 합금

Pan Lu1 , Zhang Cheng-Lin^2,6,Wang Liang³, Liu Tong⁴ and Liu Jiang-lin⁵
¹ Aviation and Materials College, Anhui Technical College of Mechanical and Electrical Engineering, Wuhu Anhui 241000, People’s
Republic of China 2 School of Engineering Science, University of Science and Technology of China, Hefei Anhui 230026, People’s Republic of China 3 Anhui Top Additive Manufacturing Technology Co., Ltd., Wuhu Anhui 241300, People’s Republic of China 4 Anhui Chungu 3D Printing Institute of Intelligent Equipment and Industrial Technology, Anhui 241300, People’s Republic of China 5 School of Mechanical and Transportation Engineering, Taiyuan University of Technology, Taiyuan Shanxi 030024, People’s Republic of
China 6 Author to whom any correspondence should be addressed.
E-mail: ahjdpanlu@126.com, jiao__zg@126.com, ahjdjxx001@126.com,tongliu1988@126.com and liujianglin@tyut.edu.cn

Keywords

SLM, molten pool, AlCu5MnCdVA alloy, heat flow, velocity flow, numerical simulation

Abstract

선택적 레이저 용융(SLM)은 열 전달, 용융, 상전이, 기화 및 물질 전달을 포함하는 복잡한 동적 비평형 프로세스인 금속 적층 제조(MAM)에서 가장 유망한 기술 중 하나가 되었습니다. 용융 풀의 특성(구조, 온도 흐름 및 속도 흐름)은 SLM의 최종 성형 품질에 결정적인 영향을 미칩니다. 이 연구에서는 선택적 레이저 용융 AlCu5MnCdVA 합금의 용융 풀 구조, 온도 흐름 및 속도장을 연구하기 위해 수치 시뮬레이션과 실험을 모두 사용했습니다.

그 결과 용융풀의 구조는 다양한 형태(깊은 오목 구조, 이중 오목 구조, 평면 구조, 돌출 구조 및 이상적인 평면 구조)를 나타냈으며, 용융 풀의 크기는 약 132 μm × 107 μm × 50 μm였습니다. : 용융풀은 초기에는 여러 구동력에 의해 깊이 15μm의 깊은 오목형상이었으나, 성형 후기에는 장력구배에 의해 높이 10μm의 돌출형상이 되었다. 용융 풀 내부의 금속 흐름은 주로 레이저 충격력, 금속 액체 중력, 표면 장력 및 반동 압력에 의해 구동되었습니다.

AlCu5MnCdVA 합금의 경우, 금속 액체 응고 속도가 매우 빠르며(3.5 × 10-4 S), 가열 속도 및 냉각 속도는 각각 6.5 × 107 K S-1 및 1.6 × 106 K S-1 에 도달했습니다. 시각적 표준으로 표면 거칠기를 선택하고, 낮은 레이저 에너지 AlCu5MnCdVA 합금 최적 공정 매개변수 창을 수치 시뮬레이션으로 얻었습니다: 레이저 출력 250W, 부화 공간 0.11mm, 층 두께 0.03mm, 레이저 스캔 속도 1.5m s-1 .

또한, 실험 프린팅과 수치 시뮬레이션과 비교할 때, 용융 풀의 폭은 각각 약 205um 및 약 210um이었고, 인접한 두 용융 트랙 사이의 중첩은 모두 약 65um이었다. 결과는 수치 시뮬레이션 결과가 실험 인쇄 결과와 기본적으로 일치함을 보여 수치 시뮬레이션 모델의 정확성을 입증했습니다.

Selective Laser Melting (SLM) has become one of the most promising technologies in Metal Additive Manufacturing (MAM), which is a complex dynamic non-equilibrium process involving heat transfer, melting, phase transition, vaporization and mass transfer. The characteristics of the molten pool (structure, temperature flow and velocity flow) have a decisive influence on the final forming quality of SLM. In this study, both numerical simulation and experiments were employed to study molten pool structure, temperature flow and velocity field in Selective Laser Melting AlCu5MnCdVA alloy. The results showed the structure of molten pool showed different forms(deep-concave structure, double-concave structure, plane structure, protruding structure and ideal planar structure), and the size of the molten pool was approximately 132 μm × 107 μm × 50 μm: in the early stage, molten pool was in a state of deep-concave shape with a depth of 15 μm due to multiple driving forces, while a protruding shape with a height of 10 μm duo to tension gradient in the later stages of forming. The metal flow inside the molten pool was mainly driven by laser impact force, metal liquid gravity, surface tension and recoil pressure. For AlCu5MnCdVA alloy, metal liquid solidification speed was extremely fast(3.5 × 10−4 S), the heating rate and cooling rate reached 6.5 × 107 K S−1 and 1.6 × 106 K S−1 , respectively. Choosing surface roughness as a visual standard, low-laser energy AlCu5MnCdVA alloy optimum process parameters window was obtained by numerical simulation: laser power 250 W, hatching space 0.11 mm, layer thickness 0.03 mm, laser scanning velocity 1.5 m s−1 . In addition, compared with experimental printing and numerical simulation, the width of the molten pool was about 205 um and about 210 um, respectively, and overlapping between two adjacent molten tracks was all about 65 um. The results showed that the numerical simulation results were basically consistent with the experimental print results, which proved the correctness of the numerical simulation model.

Figure 1. AlCu5MnCdVA powder particle size distribution.

Figure 3. Finite element model and calculation domains of SLM.

Figure 17. Two-pass molten tracks overlapping for Scheme NO.2.

References

[1] Cuiyun H 2008 Phase diagram determination and thermodynamic study of Al–Cu–Mn, Al–Cu–Si, Al–Mg–Ni and Ni–Ti–Si systems Central South University
[2] Zhanfei Z 2017 Study on theta phase segregation and room temperature properties of high strength cast Al–Cu–Mn alloy Lanzhou University of Technology
[3] Nie X et al 2018 Analysis of processing parameters and characteristics of selective laser melted high strength Al–Cu–Mg alloys: from single tracks to cubic samplesJ. Mater. Process. Technol. 256 69–77
[4] Shenping Y et al 2017 Laser absorptance measurement of commonly used metal materials in laser additive manufacturing technology Aviation Manufacturing Technology 12 23–9
[5] Wenqing W 2007 Relationship between cooling rate and grain size of AlCu5MnCdVA alloy Harbin University of Technology
[6] Majeed M, Vural M, Raja S and Bilal Naim Shaikh M 2019 Finite element analysis of thermal behavior in maraging steel during SLM process Optik 208 113–24
[7] Khairallah S A, Anderson A T, Rubenchik A and King W E 2016 Laser powder-bed fusion additive manufacturing: physics of complex melt flow and formation mechanisms of pores, spatter, and denudation zones Acta Mater. 108 36–45
[8] Bo C, Zhiyu X, Quanquan Z, Yuanbiao W, Liping W and Jin C 2020 Process optimization and microstructure and properties of SLM forming Cu6AlNiSnInCe imitation gold alloy Chin. J. Nonferr. Met. 30 372–82
[9] Li W 2012 Research on performance of metal parts formed by selective laser melting Huazhong University of Science and Technology
[10] Yu Q 2013 The influence of different laser heat sources on the surface shape of the molten pool in laser cladding Surf. Technol. 42 40–3

[11] Xianfeng J, Xiangchen M, Rongwei S, Xigen Y and Ming Y 2015 Research on the influence of material state change on temperature field
in SLM processing Applied Laser 35 155–9
[12] Körner C, Attar E and Heinl P 2011 Mesoscopic simulation of selective beam melting processesJ. Mater. Process. Technol. 211 978–87
[13] Yadroitsev I, Gusarov A, Yadroitsava I and Smurov I 2010 Single track formation in selective laser melting of metal powdersJ. Mater.
Process. Technol. 210 1624–31
[14] King W, Anderson A T, Ferencz R M, Hodge N E, Kamath C and Khairallah S A 2014 Overview of modelling and simulation of metal
powder bed fusion process at Lawrence Livermore National Laboratory Mater. Sci. Technol. 31 957–68
[15] Hussein A, Hao L, Yan C and Everson R 2013 Finite element simulation of the temperature and stress fields in single layers built
without-support in selective laser melting Materials & Design (1980–2015) 52 638–47
[16] Qiu C, Panwisawas C, Ward M, Basoalto H C, Brooks J W and Attallah M M 2015 On the role of melt flow into the surface structure and
porosity development during selective laser melting Acta Mater. 96 72–9
[17] Weihao Y, Hui C and Qingsong W 2020 Thermodynamic behavior of laser selective melting molten pool under the action of recoil
pressure Journal of Mechanical Engineering 56 213–9
[18] Weijuan Y 2019 Numerical simulation of melt pool temperature field and morphology evolution during laser selective melting process
Xi’an University of Technology
[19] Genwang W 2017 Research on the establishment of laser heat source model based on energy distribution and its simulation application
Harbin Institute of Technology
[20] FLOW-3D 2017 User Manual (USA: FLOW SCIENCE)
[21] Hirt C and Nichols B 1981 Volume of fluid (VOF) method for the dynamics of free boundariesJ. Comput. Phys. 39 201–25
[22] Hu Z, Zhang H, Zhu H, Xiao Z, Nie X and Zeng X 2019 Microstructure, mechanical properties and strengthening mechanisms of
AlCu5MnCdVA aluminum alloy fabricated by selective laser melting Materials Science and Engineering: A 759 154–66
[23] Ketai H, Liu Z and Lechang Y 2020 Simulation of temperature field, microstructure and mechanical properties of 316L stainless steel in
selected laser melting Progress in Laser and Optoelectronics 9 1–18
[24] Cao L 2020 Workpiece-scale numerical simulations of SLM molten pool dynamic behavior of 316L stainless steel Comput. Math. Appl.
4 22–34
[25] Dening Z, Yongping L, Tinglu H and Junyi S 2000 Numerical study of fluid flow and heat transfer in molten pool under the condition of
moving heat source J. Met. 4 387–90
[26] Chengyun C, Cui F and Wenlong Z 2018 The effect of Marangoni flow on the thermal behavior and melt flow behavior of laser cladding
Applied Laser 38 409–16
[27] Peiying B and Enhuai Y 2020 The effect of laser power on the morphology and residual stress of the molten pool of metal laser selective
melting Progress in Laser and Optoelectronics 7 1–12 http://kns.cnki.net/kcms/detail/31.1690.TN.20190717.0933.032.html
[28] Zhen L, Dongyun Z, Zhe F and Chengjie W 2017 Numerical simulation of the influence of overlap rate on the forming quality of
Inconel 718 alloy by selective laser melting processing Applied Laser 37 187–93
[29] Wei W, Qi L, Guang Y, Lanyun Q and Xiong X 2015 Numerical simulation of electromagnetic field, temperature field and flowfield of
laser melting pool under the action of electromagnetic stirring China Laser 42 48–55
[30] Hu Y, He X, Yu G and Zhao S 2016 Capillary convection in pulsed—butt welding of miscible dissimilar couple Proc. Inst. Mech. Eng.
Part C J. Mech. Eng. Sci. 231 2429–40
[31] Li R 2010 Research on the key basic problems of selective laser melting forming of metal powder Huazhong University of Science and
Technology
[32] Zijue T, Weiwei L, Zhaorui Y, Hao W and Hongchao Z 2019 Study on the shape evolution behavior of metal laser melting deposition
based on molten pool dynamic characteristicsJournal of Mechanical Engineering 55 39–47
[33] Pan L, Cheng-Lin Z, Hai-Yi L, Liang W and Tong L 2020 A new two-step selective laser remelting of 316L stainless steel: process,
density, surface roughness, mechanical properties, microstructure Mater. Res. Express 7 056503
[34] Pan L, Cheng-Lin Z, Hai-Yi L, Jiang H, Tong L and Liang W 2019 The influence and optimization of forming process parameters of
316L stainless steel prepared by laser melting on the density Forging Technology 44 103–9

원본보기

Figure 5 A schematic of the water model of reactor URO 200.

Physical and Numerical Modeling of the Impeller Construction Impact on the Aluminum Degassing Process

알루미늄 탈기 공정에 미치는 임펠러 구성의 물리적 및 수치적 모델링

Kamil Kuglin,¹ Michał Szucki,² Jacek Pieprzyca,³ Simon Genthe,² Tomasz Merder,³ and Dorota Kalisz^1,^*

Mikael Ersson, Academic Editor

Author information Article notes Copyright and License information Disclaimer

Associated Data

Data Availability Statement

Go to:

Abstract

This paper presents the results of tests on the suitability of designed heads (impellers) for aluminum refining. The research was carried out on a physical model of the URO-200, followed by numerical simulations in the FLOW 3D program. Four design variants of impellers were used in the study. The degree of dispersion of the gas phase in the model liquid was used as a criterion for evaluating the performance of each solution using different process parameters, i.e., gas flow rate and impeller speed. Afterward, numerical simulations in Flow 3D software were conducted for the best solution. These simulations confirmed the results obtained with the water model and verified them.

Keywords: aluminum, impeller construction, degassing process, numerical modeling, physical modeling

Go to:

1. Introduction

Constantly increasing requirements concerning metallurgical purity in terms of hydrogen content and nonmetallic inclusions make casting manufacturers use effective refining techniques. The answer to this demand is the implementation of the aluminum refining technique making use of a rotor with an original design guaranteeing efficient refining [1,2,3,4]. The main task of the impeller (rotor) is to reduce the contamination of liquid metal (primary and recycled aluminum) with hydrogen and nonmetallic inclusions. An inert gas, mainly argon or a mixture of gases, is introduced through the rotor into the liquid metal to bring both hydrogen and nonmetallic inclusions to the metal surface through the flotation process. Appropriately and uniformly distributed gas bubbles in the liquid metal guarantee achieving the assumed level of contaminant removal economically. A very important factor in deciding about the obtained degassing effect is the optimal rotor design [5,6,7,8]. Thanks to the appropriate geometry of the rotor, gas bubbles introduced into the liquid metal are split into smaller ones, and the spinning movement of the rotor distributes them throughout the volume of the liquid metal bath. In this solution impurities in the liquid metal are removed both in the volume and from the upper surface of the metal. With a well-designed impeller, the costs of refining aluminum and its alloys can be lowered thanks to the reduced inert gas and energy consumption (optimal selection of rotor rotational speed). Shorter processing time and a high degree of dehydrogenation decrease the formation of dross on the metal surface (waste). A bigger produced dross leads to bigger process losses. Consequently, this means that the choice of rotor geometry has an indirect impact on the degree to which the generated waste is reduced [9,10].

Another equally important factor is the selection of process parameters such as gas flow rate and rotor speed [11,12]. A well-designed gas injection system for liquid metal meets two key requirements; it causes rapid mixing of the liquid metal to maintain a uniform temperature throughout the volume and during the entire process, to produce a chemically homogeneous metal composition. This solution ensures effective degassing of the metal bath. Therefore, the shape of the rotor, the arrangement of the nozzles, and their number are significant design parameters that guarantee the optimum course of the refining process. It is equally important to complete the mixing of the metal bath in a relatively short time, as this considerably shortens the refining process and, consequently, reduces the process costs. Another important criterion conditioning the implementation of the developed rotor is the generation of fine diffused gas bubbles which are distributed throughout the metal volume, and whose residence time will be sufficient for the bubbles to collide and adsorb the contaminants. The process of bubble formation by the spinning rotors differs from that in the nozzles or porous molders. In the case of a spinning rotor, the shear force generated by the rotor motion splits the bubbles into smaller ones. Here, the rotational speed, mixing force, surface tension, and fluid density have a key effect on the bubble size. The velocity of the bubbles, which depends mainly on their size and shape, determines their residence time in the reactor and is, therefore, very important for the refining process, especially since gas bubbles in liquid aluminum may remain steady only below a certain size [13,14,15].

The impeller designs presented in the article were developed to improve the efficiency of the process and reduce its costs. The impellers used so far have a complicated structure and are very pricey. The success of the conducted research will allow small companies to become independent of external supplies through the possibility of making simple and effective impellers on their own. The developed structures were tested on the water model. The results of this study can be considered as pilot.

Go to:

2. Materials and Methods

Rotors were realized with the SolidWorks computer design technique and a 3D printer. The developed designs were tested on a water model. Afterward, the solution with the most advantageous refining parameters was selected and subjected to calculations with the Flow3D package. As a result, an impeller was designed for aluminum refining. Its principal lies in an even distribution of gas bubbles in the entire volume of liquid metal, with the largest possible participation of the bubble surface, without disturbing the metal surface. This procedure guarantees the removal of gaseous, as well as metallic and nonmetallic, impurities.

2.1. Rotor Designs

The developed impeller constructions, shown in Figure 1, Figure 2, Figure 3 and Figure 4, were printed on a 3D printer using the PLA (polylactide) material. The impeller design models differ in their shape and the number of holes through which the inert gas flows. Figure 1, Figure 2 and Figure 3 show the same impeller model but with a different number of gas outlets. The arrangement of four, eight, and 12 outlet holes was adopted in the developed design. A triangle-shaped structure equipped with three gas outlet holes is presented in Figure 4.

An external file that holds a picture, illustration, etc.
Object name is materials-15-05273-g001.jpg

Figure 1

A 3D model—impeller with four holes—variant B4.

An external file that holds a picture, illustration, etc.
Object name is materials-15-05273-g002.jpg

Figure 2

A 3D model—impeller with eight holes—variant B8.

An external file that holds a picture, illustration, etc.
Object name is materials-15-05273-g003.jpg

Figure 3

A 3D model—impeller with twelve holes—variant B12.

An external file that holds a picture, illustration, etc.
Object name is materials-15-05273-g004.jpg

Figure 4

A 3D model—‘red triangle’ impeller with three holes—variant RT3.

2.2. Physical Models

Investigations were carried out on a water model of the URO 200 reactor of the barbotage refining process (see Figure 5).

An external file that holds a picture, illustration, etc.
Object name is materials-15-05273-g005.jpg

Figure 5

A schematic of the water model of reactor URO 200.

The URO 200 reactor can be classified as a cyclic reactor. The main element of the device is a rotor, which ends the impeller. The whole system is attached to a shaft via which the refining gas is supplied. Then, the shaft with the rotor is immersed in the liquid metal in the melting pot or the furnace chamber. In URO 200 reactors, the refining process lasts 600 s (10 min), the gas flow rate that can be obtained ranges from 5 to 20 dm³·min⁻¹, and the speed at which the rotor can move is 0 to 400 rpm. The permissible quantity of liquid metal for barbotage refining is 300 kg or 700 kg [8,16,17]. The URO 200 has several design solutions which improve operation and can be adapted to the existing equipment in the foundry. These solutions include the following [8,16]:

URO-200XR—used for small crucible furnaces, the capacity of which does not exceed 250 kg, with no control system and no control of the refining process.
URO-200SA—used to service several crucible furnaces of capacity from 250 kg to 700 kg, fully automated and equipped with a mechanical rotor lift.
URO-200KA—used for refining processes in crucible furnaces and allows refining in a ladle. The process is fully automated, with a hydraulic rotor lift.
URO-200KX—a combination of the XR and KA models, designed for the ladle refining process. Additionally, refining in heated crucibles is possible. The unit is equipped with a manual hydraulic rotor lift.
URO-200PA—designed to cooperate with induction or crucible furnaces or intermediate chambers, the capacity of which does not exceed one ton. This unit is an integral part of the furnace. The rotor lift is equipped with a screw drive.

Studies making use of a physical model can be associated with the observation of the flow and circulation of gas bubbles. They require meeting several criteria regarding the similarity of the process and the object characteristics. The similarity conditions mainly include geometric, mechanical, chemical, thermal, and kinetic parameters. During simulation of aluminum refining with inert gas, it is necessary to maintain the geometric similarity between the model and the real object, as well as the similarity related to the flow of liquid metal and gas (hydrodynamic similarity). These quantities are characterized by the Reynolds, Weber, and Froude numbers. The Froude number is the most important parameter characterizing the process, its magnitude is the same for the physical model and the real object. Water was used as the medium in the physical modeling. The factors influencing the choice of water are its availability, relatively low cost, and kinematic viscosity at room temperature, which is very close to that of liquid aluminum.

The physical model studies focused on the flow of inert gas in the form of gas bubbles with varying degrees of dispersion, particularly with respect to some flow patterns such as flow in columns and geysers, as well as disturbance of the metal surface. The most important refining parameters are gas flow rate and rotor speed. The barbotage refining studies for the developed impeller (variants B4, B8, B12, and RT3) designs were conducted for the following process parameters:

Rotor speed: 200, 300, 400, and 500 rpm,
Ideal gas flow: 10, 20, and 30 dm³·min⁻¹,
Temperature: 293 K (20 °C).

These studies were aimed at determining the most favorable variants of impellers, which were then verified using the numerical modeling methods in the Flow-3D program.

2.3. Numerical Simulations with Flow-3D Program

Testing different rotor impellers using a physical model allows for observing the phenomena taking place while refining. This is a very important step when testing new design solutions without using expensive industrial trials. Another solution is modeling by means of commercial simulation programs such as ANSYS Fluent or Flow-3D [18,19]. Unlike studies on a physical model, in a computer program, the parameters of the refining process and the object itself, including the impeller design, can be easily modified. The simulations were performed with the Flow-3D program version 12.03.02. A three-dimensional system with the same dimensions as in the physical modeling was used in the calculations. The isothermal flow of liquid–gas bubbles was analyzed. As in the physical model, three speeds were adopted in the numerical tests: 200, 300, and 500 rpm. During the initial phase of the simulations, the velocity field around the rotor generated an appropriate direction of motion for the newly produced bubbles. When the required speed was reached, the generation of randomly distributed bubbles around the rotor was started at a rate of 2000 per second. Table 1 lists the most important simulation parameters.

Table 1

Values of parameters used in the calculations.

Parameter	Value	Unit
Maximum number of gas particles	1,000,000	–
Rate of particle generation	2000	1·s⁻¹
Specific gas constant	287.058	J·kg⁻¹·K⁻¹
Atmospheric pressure	1.013 × 10⁵	Pa
Water density	1000	kg·m⁻³
Water viscosity	0.001	kg·m⁻¹·s⁻¹
Boundary condition on the walls	No-slip	–
Size of computational cell	0.0034	m

Open in a separate window

In the case of the CFD analysis, the numerical solutions require great care when generating the computational mesh. Therefore, computational mesh tests were performed prior to the CFD calculations. The effect of mesh density was evaluated by taking into account the velocity of water in the tested object on the measurement line A (height of 0.065 m from the bottom) in a characteristic cross-section passing through the object axis (see Figure 6). The mesh contained 3,207,600, 6,311,981, 7,889,512, 11,569,230, and 14,115,049 cells.

An external file that holds a picture, illustration, etc.
Object name is materials-15-05273-g006.jpg

Figure 6

The velocity of the water depending on the size of the computational grid.

The quality of the generated computational meshes was checked using the criterion skewness angle Q_EAS [18]. This criterion is described by the following relationship:

QEAS=max{βmax−βeq180−βeq,βeq−βminβeq},

(1)

where β_max, β_min are the maximal and minimal angles (in degrees) between the edges of the cell, and β_eq is the angle corresponding to an ideal cell, which for cubic cells is 90°.

Normalized in the interval [0;1], the value of Q_EAS should not exceed 0.75, which identifies the permissible skewness angle of the generated mesh. For the computed meshes, this value was equal to 0.55–0.65.

Moreover, when generating the computational grids in the studied facility, they were compacted in the areas of the highest gradients of the calculated values, where higher turbulence is to be expected (near the impeller). The obtained results of water velocity in the studied object at constant gas flow rate are shown in Figure 6.

The analysis of the obtained water velocity distributions (see Figure 6) along the line inside the object revealed that, with the density of the grid of nodal points, the velocity changed and its changes for the test cases of 7,889,512, 11,569,230, and 14,115,049 were insignificant. Therefore, it was assumed that a grid containing not less than 7,900,000 (7,889,512) cells would not affect the result of CFD calculations.

A single-block mesh of regular cells with a size of 0.0034 m was used in the numerical calculations. The total number of cells was approximately 7,900,000 (7,889,512). This grid resolution (see Figure 7) allowed the geometry of the system to be properly represented, maintaining acceptable computation time (about 3 days on a workstation with 2× CPU and 12 computing cores).

An external file that holds a picture, illustration, etc.
Object name is materials-15-05273-g007.jpg

Figure 7

Structured equidistant mesh used in numerical calculations: (a) mesh with smoothed, surface cells (the so-called FAVOR method) used in Flow-3D; (b) visualization of the applied mesh resolution.

The calculations were conducted with an explicit scheme. The timestep was selected by the program automatically and controlled by stability and convergence. From the moment of the initial velocity field generation (start of particle generation), it was 0.0001 s.

When modeling the degassing process, three fluids are present in the system: water, gas supplied through the rotor head (impeller), and the surrounding air. Modeling such a multiphase flow is a numerically very complex issue. The necessity to overcome the liquid backpressure by the gas flowing out from the impeller leads to the formation of numerical instabilities in the volume of fluid (VOF)-based approach used by Flow-3D software. Therefore, a mixed description of the analyzed flow was used here. In this case, water was treated as a continuous medium, while, in the case of gas bubbles, the discrete phase model (DPM) model was applied. The way in which the air surrounding the system was taken into account is later described in detail.

The following additional assumptions were made in the modeling:

—The liquid phase was considered as an incompressible Newtonian fluid.
—The effect of chemical reactions during the refining process was neglected.
—The composition of each phase (gas and liquid) was considered homogeneous; therefore, the viscosity and surface tension were set as constants.
—Only full turbulence existed in the liquid, and the effect of molecular viscosity was neglected.
—The gas bubbles were shaped as perfect spheres.
—The mutual interaction between gas bubbles (particles) was neglected.

2.3.1. Modeling of Liquid Flow

The motion of the real fluid (continuous medium) is described by the Navier–Stokes Equation [20].

dudt=−1ρ∇p+ν∇2u+13ν∇(∇⋅ u)+F,

(2)

where du/dt is the time derivative, u is the velocity vector, t is the time, and F is the term accounting for external forces including gravity (unit components denoted by X, Y, Z).

In the simulations, the fluid flow was assumed to be incompressible, in which case the following equation is applicable:

∂u∂t+(u⋅∇)u=−1ρ∇p+ν∇2u+F.

(3)

Due to the large range of liquid velocities during flows, the turbulence formation process was included in the modeling. For this purpose, the k–ε model turbulence kinetic energy k and turbulence dissipation ε were the target parameters, as expressed by the following equations [21]:

∂(ρk)∂t+∂(ρkvi)∂xi=∂∂xj[(μ+μtσk)⋅∂k∂xi]+Gk+Gb−ρε−Ym+Sk,

(4)

∂(ρε)∂t+∂(ρεui)∂xi=∂∂xj[(μ+μtσε)⋅∂k∂xi]+C1εεk(Gk+G3εGb)+C2ερε2k+Sε,

(5)

where ρ is the gas density, σ_κ and σ_ε are the Prandtl turbulence numbers, k and ε are constants of 1.0 and 1.3, and G_k and G_b are the kinetic energy of turbulence generated by the average velocity and buoyancy, respectively.

As mentioned earlier, there are two gas phases in the considered problem. In addition to the gas bubbles, which are treated here as particles, there is also air, which surrounds the system. The boundary of phase separation is in this case the free surface of the water. The shape of the free surface can change as a result of the forming velocity field in the liquid. Therefore, it is necessary to use an appropriate approach to free surface tracking. The most commonly used concept in liquid–gas flow modeling is the volume of fluid (VOF) method [22,23], and Flow-3D uses a modified version of this method called TrueVOF. It introduces the concept of the volume fraction of the liquid phase f_l. This parameter can be used for classifying the cells of a discrete grid into areas filled with liquid phase (f_l = 1), gaseous phase, or empty cells (f_l = 0) and those through which the phase separation boundary (f_l ∈ (0, 1)) passes (free surface). To determine the local variations of the liquid phase fraction, it is necessary to solve the following continuity equation:

dfldt=0.

(6)

Then, the fluid parameters in the region of coexistence of the two phases (the so-called interface) depend on the volume fraction of each phase.

ρ=flρl+(1−fl)ρg,

(7)

ν=flνl+(1−fl)νg,

(8)

where indices l and g refer to the liquid and gaseous phases, respectively.

The parameter of fluid velocity in cells containing both phases is also determined in the same way.

u=flul+(1−fl)ug.

(9)

Since the processes taking place in the surrounding air can be omitted, to speed up the calculations, a single-phase, free-surface model was used. This means that no calculations were performed in the gas cells (they were treated as empty cells). The liquid could fill them freely, and the air surrounding the system was considered by the atmospheric pressure exerted on the free surface. This approach is often used in modeling foundry and metallurgical processes [24].

2.3.2. Modeling of Gas Bubble Flow

As stated, a particle model was used to model bubble flow. Spherical particles (gas bubbles) of a given size were randomly generated in the area marked with green in Figure 7b. In the simulations, the gas bubbles were assumed to have diameters of 0.016 and 0.02 m corresponding to the gas flow rates of 10 and 30 dm³·min⁻¹, respectively.

Experimental studies have shown that, as a result of turbulent fluid motion, some of the bubbles may burst, leading to the formation of smaller bubbles, although merging of bubbles into larger groupings may also occur. Therefore, to be able to observe the behavior of bubbles of different sizes (diameter), the calculations generated two additional particle types with diameters twice smaller and twice larger, respectively. The proportion of each species in the system was set to 33.33% (Table 2).

Table 2

Data assumed for calculations.

No	Rotor Speed (Rotational Speed) rpm	Bubbles Diameter m	Corresponding Gas Flow Rate dm³·min⁻¹	No	Rotor Speed (Rotational Speed) rpm	Bubbles Diameter m	Corresponding Gas Flow Rate dm³·min⁻¹
A	200	0.016	10	D	200	0.02	30
0.008	0.01
0.032	0.04
B	300	0.016	10	E	300	0.02	30
0.008	0.01
0.032	0.04
C	500	0.016	10	F	500	0.02	30
0.008	0.01
0.032	0.04

Open in a separate window

The velocity of the particle results from the generated velocity field (calculated from Equation (3) in the liquid ul around it and its velocity resulting from the buoyancy force ub. The effect of particle radius r on the terminal velocity associated with buoyancy force can be determined according to Stokes’ law.

ub=29 (ρg−ρl)μlgr2,

(10)

where g is the acceleration (9.81).

The DPM model was used for modeling the two-phase (water–air) flow. In this model, the fluid (water) is treated as a continuous phase and described by the Navier–Stokes equation, while gas bubbles are particles flowing in the model fluid (discrete phase). The trajectories of each bubble in the DPM system are calculated at each timestep taking into account the mass forces acting on it. Table 3 characterizes the DPM model used in our own research [18].

Table 3

Characteristic of the DPM model.

Method	Equations
Euler–Lagrange	Balance equation: dugdt=FD(u−ug)+g(ϱg−ϱ)ϱg+F. F_D (u − u_p) denotes the drag forces per mass unit of a bubble, and the expression for the drag coefficient F_D is of the form FD=18μCDReϱ⋅gd2g24. The relative Reynolds number has the form Re≡ρdg\|ug−u\|μ. On the other hand, the force resulting from the additional acceleration of the model fluid has the form F=12dρdtρg(u−ug), where u_g is the gas bubble velocity, u is the liquid velocity, d_g is the bubble diameter, and C_D is the drag coefficient.

Method

Equations

Euler–Lagrange

Balance equation:
dugdt=FD(u−ug)+g(ϱg−ϱ)ϱg+F.
F_D (u − u_p) denotes the drag forces per mass unit of a bubble, and the expression for the drag coefficient F_D is of the form
FD=18μCDReϱ⋅gd2g24.
The relative Reynolds number has the form
Re≡ρdg|ug−u|μ.
On the other hand, the force resulting from the additional acceleration of the model fluid has the form
F=12dρdtρg(u−ug),
where u_g is the gas bubble velocity, u is the liquid velocity, d_g is the bubble diameter, and C_D is the drag coefficient.

Open in a separate window

Go to:

3. Results and Discussion

3.1. Calculations of Power and Mixing Time by the Flowing Gas Bubbles

One of the most important parameters of refining with a rotor is the mixing power induced by the spinning rotor and the outflowing gas bubbles (via impeller). The mixing power of liquid metal in a ladle of height (h) by gas injection can be determined from the following relation [15]:

pgVm=ρ⋅g⋅uB,

(11)

where p_g is the mixing power, V_m is the volume of liquid metal in the reactor, ρ is the density of liquid aluminum, and u_B is the average speed of bubbles, given below.

uB=n⋅R⋅TAc⋅Pm⋅t,

(12)

where n is the number of gas moles, R is the gas constant (8.314), A_c is the cross-sectional area of the reactor vessel, T is the temperature of liquid aluminum in the reactor, and P_m is the pressure at the middle tank level. The pressure at the middle level of the tank is calculated by a function of the mean logarithmic difference.

Pm=(Pa+ρ⋅g⋅h)−Paln(Pa+ρ⋅g⋅h)Pa,

(13)

where P_a is the atmospheric pressure, and h is the the height of metal in the reactor.

Themelis and Goyal [25] developed a model for calculating mixing power delivered by gas injection.

pg=2Q⋅R⋅T⋅ln(1+m⋅ρ⋅g⋅hP),

(14)

where Q is the gas flow, and m is the mass of liquid metal.

Zhang [26] proposed a model taking into account the temperature difference between gas and alloy (metal).

pg=QRTgVm[ln(1+ρ⋅g⋅hPa)+(1−TTg)],

(15)

where T_g is the gas temperature at the entry point.

Data for calculating the mixing power resulting from inert gas injection into liquid aluminum are given below in Table 4. The design parameters were adopted for the model, the parameters of which are shown in Figure 5.

Table 4

Data for calculating mixing power introduced by an inert gas.

Parameter	Value	Unit
Height of metal column	0.7	m
Density of aluminum	2375	kg·m⁻³
Process duration	20	s
Gas temperature at the injection site	940	K
Cross-sectional area of ladle	0.448	m²
Mass of liquid aluminum	546.25	kg
Volume of ladle	0.23	M³
Temperature of liquid aluminum	941.15	K

Open in a separate window

Table 5 presents the results of mixing power calculations according to the models of Themelis and Goyal and of Zhang for inert gas flows of 10, 20, and 30 dm³·min⁻¹. The obtained calculation results significantly differed from each other. The difference was an order of magnitude, which indicates that the model is highly inaccurate without considering the temperature of the injected gas. Moreover, the calculations apply to the case when the mixing was performed only by the flowing gas bubbles, without using a rotor, which is a great simplification of the phenomenon.

Table 5

Mixing power calculated from mathematical models.

Mathematical Model	Mixing Power (W·t⁻¹) for a Given Inert Gas Flow (dm³·min⁻¹)
	10	20	30
Themelis and Goyal	11.49	23.33	35.03
Zhang	0.82	1.66	2.49

Open in a separate window

The mixing time is defined as the time required to achieve 95% complete mixing of liquid metal in the ladle [27,28,29,30]. Table 6 groups together equations for the mixing time according to the models.

Table 6

Models for calculating mixing time.

Authors	Model	Remarks
Szekely [31]	τ=800ε−0.4	ε—W·t⁻¹
Chiti and Paglianti [27]	τ=CVQl	V—volume of reactor, m³ Ql—flow intensity, m³·s⁻¹
Iguchi and Nakamura [32]	τ=1200⋅Q−0.4D1.97h−1.0υ0.47	υ—kinematic viscosity, m²·s⁻¹ D—diameter of ladle, m h—height of metal column, m Q—liquid flow intensity, m³·s⁻¹

Open in a separate window

Figure 8 and Figure 9 show the mixing time as a function of gas flow rate for various heights of the liquid column in the ladle and mixing power values.

An external file that holds a picture, illustration, etc.
Object name is materials-15-05273-g008.jpg

Figure 8

Mixing time as a function of gas flow rate for various heights of the metal column (Iguchi and Nakamura model).

An external file that holds a picture, illustration, etc.
Object name is materials-15-05273-g009.jpg

Figure 9

Mixing time as a function of mixing power (Szekly model).

3.2. Determining the Bubble Size

The mechanisms controlling bubble size and mass transfer in an alloy undergoing refining are complex. Strong mixing conditions in the reactor promote impurity mass transfer. In the case of a spinning rotor, the shear force generated by the rotor motion separates the bubbles into smaller bubbles. Rotational speed, mixing force, surface tension, and liquid density have a strong influence on the bubble size. To characterize the kinetic state of the refining process, parameters k and A were introduced. Parameters k, A, and u_B can be calculated using the below equations [33].

k=2D⋅uBdB⋅π−−−−−−√,

(16)

A=6Q⋅hdB⋅uB,

(17)

uB=1.02g⋅dB,−−−−−√

(18)

where D is the diffusion coefficient, and d_B is the bubble diameter.

After substituting appropriate values, we get

dB=3.03×104(πD)−2/5g−1/5h4/5Q0.344N−1.48.

(19)

According to the last equation, the size of the gas bubble decreases with the increasing rotational speed (see Figure 10).

An external file that holds a picture, illustration, etc.
Object name is materials-15-05273-g010.jpg

Figure 10

Effect of rotational speed on the bubble diameter.

In a flow of given turbulence intensity, the diameter of the bubble does not exceed the maximum size d_max, which is inversely proportional to the rate of kinetic energy dissipation in a viscous flow ε. The size of the gas bubble diameter as a function of the mixing energy, also considering the Weber number and the mixing energy in the negative power, can be determined from the following equations [31,34]:

—Sevik and Park:

dBmax=We0.6kr⋅(σ⋅103ρ⋅10−3)0.6⋅(10⋅ε)−0.4⋅10−2.

(20)

—Evans:

dBmax=⎡⎣Wekr⋅σ⋅1032⋅(ρ⋅10−3)13⎤⎦35 ⋅(10⋅ε)−25⋅10−2.

(21)

The results of calculating the maximum diameter of the bubble d_Bmax determined from Equation (21) are given in Table 7.

Table 7

The results of calculating the maximum diameter of the bubble using Equation (21).

Model	Mixing Energy ĺ (m²·s⁻³)	Weber Number (We_kr)
0.59	1.0	1.2
Zhang and Taniguchi d_max	0.1	0.0167	0.0230	0.026
0.5	0.0088	0.0121	0.013
1.0	0.0067	0.0091	0.010
1.5	0.0057	0.0078	0.009
Sevik and Park d_B_max	0.1	0.265	0.36	0.41
0.5	0.139	0.19	0.21
1.0	0.106	0.14	0.16
1.5	0.090	0.12	0.14
Evans d_B_max	0.1	0.247	0.340	0.38
0.5	0.130	0.178	0.20
1.0	0.098	0.135	0.15
1.5	0.084	0.115	0.13

Open in a separate window

3.3. Physical Modeling

The first stage of experiments (using the URO-200 water model) included conducting experiments with impellers equipped with four, eight, and 12 gas outlets (variants B4, B8, B12). The tests were carried out for different process parameters. Selected results for these experiments are presented in Figure 11, Figure 12, Figure 13 and Figure 14.

An external file that holds a picture, illustration, etc.
Object name is materials-15-05273-g011.jpg

Figure 11

Impeller variant B4—gas bubbles dispersion registered for a gas flow rate of 10 dm³·min⁻¹ and rotor speed of (a) 200, (b) 300, (c) 400, and (d) 500 rpm.

An external file that holds a picture, illustration, etc.
Object name is materials-15-05273-g012.jpg

Figure 12

Impeller variant B8—gas bubbles dispersion registered for a gas flow rate of 10 dm³·min⁻¹ and rotor speed of (a) 200, (b) 300, (c) 400, and (d) 500 rpm.

An external file that holds a picture, illustration, etc.
Object name is materials-15-05273-g013.jpg

Figure 13

Gas bubble dispersion registered for different processing parameters (impeller variant B12).

An external file that holds a picture, illustration, etc.
Object name is materials-15-05273-g014.jpg

Figure 14

Gas bubble dispersion registered for different processing parameters (impeller variant RT3).

The analysis of the refining variants presented in Figure 11, Figure 12, Figure 13 and Figure 14 reveals that the proposed impellers design model is not useful for the aluminum refining process. The number of gas outlet orifices, rotational speed, and flow did not affect the refining efficiency. In all the variants shown in the figures, very poor dispersion of gas bubbles was observed in the object. The gas bubble flow had a columnar character, and so-called dead zones, i.e., areas where no inert gas bubbles are present, were visible in the analyzed object. Such dead zones were located in the bottom and side zones of the ladle, while the flow of bubbles occurred near the turning rotor. Another negative phenomenon observed was a significant agitation of the water surface due to excessive (rotational) rotor speed and gas flow (see Figure 13, cases 20; 400, 30; 300, 30; 400, and 30; 500).

Research results for a ‘red triangle’ impeller equipped with three gas supply orifices (variant RT3) are presented in Figure 14.

In this impeller design, a uniform degree of bubble dispersion in the entire volume of the modeling fluid was achieved for most cases presented (see Figure 14). In all tested variants, single bubbles were observed in the area of the water surface in the vessel. For variants 20; 200, 30; 200, and 20; 300 shown in Figure 14, the bubble dispersion results were the worst as the so-called dead zones were identified in the area near the bottom and sidewalls of the vessel, which disqualifies these work parameters for further applications. Interestingly, areas where swirls and gas bubble chains formed were identified only for the inert gas flows of 20 and 30 dm³·min⁻¹ and 200 rpm in the analyzed model. This means that the presented model had the best performance in terms of dispersion of gas bubbles in the model liquid. Its design with sharp edges also differed from previously analyzed models, which is beneficial for gas bubble dispersion, but may interfere with its suitability in industrial conditions due to possible premature wear.

3.4. Qualitative Comparison of Research Results (CFD and Physical Model)

The analysis (physical modeling) revealed that the best mixing efficiency results were obtained with the RT3 impeller variant. Therefore, numerical calculations were carried out for the impeller model with three outlet orifices (variant RT3). The CFD results are presented in Figure 15 and Figure 16.

An external file that holds a picture, illustration, etc.
Object name is materials-15-05273-g015.jpg

Figure 15

Simulation results of the impeller RT3, for given flows and rotational speeds after a time of 1 s: simulation variants (a) A, (b) B, (c) C, (d) D, (e) E, and (f) F.

An external file that holds a picture, illustration, etc.
Object name is materials-15-05273-g016.jpg

Figure 16

Simulation results of the impeller RT3, for given flows and rotational speeds after a time of 5.4 s.: simulation variants (a) A, (b) B, (c) C, (d) D, (e) E, and (f) F.

CFD results are presented for all analyzed variants (impeller RT3) at two selected calculation timesteps of 1 and 5.40 s. They show the velocity field of the medium (water) and the dispersion of gas bubbles.

Figure 15 shows the initial refining phase after 1 s of the process. In this case, the gas bubble formation and flow were observed in an area close to contact with the rotor. Figure 16 shows the phase when the dispersion and flow of gas bubbles were advanced in the reactor area of the URO-200 model.

The quantitative evaluation of the obtained results of physical and numerical model tests was based on the comparison of the degree of gas dispersion in the model liquid. The degree of gas bubble dispersion in the volume of the model liquid and the areas of strong turbulent zones formation were evaluated during the analysis of the results of visualization and numerical simulations. These two effects sufficiently characterize the required course of the process from the physical point of view. The known scheme of the below description was adopted as a basic criterion for the evaluation of the degree of dispersion of gas bubbles in the model liquid.

Minimal dispersion—single bubbles ascending in the region of their formation along the ladle axis; lack of mixing in the whole bath volume.
Accurate dispersion—single and well-mixed bubbles ascending toward the bath mirror in the region of the ladle axis; no dispersion near the walls and in the lower part of the ladle.
Uniform dispersion—most desirable; very good mixing of fine bubbles with model liquid.
Excessive dispersion—bubbles join together to form chains; large turbulence zones; uneven flow of gas.

The numerical simulation results give a good agreement with the experiments performed with the physical model. For all studied variants (used process parameters), the single bubbles were observed in the area of water surface in the vessel. For variants presented in Figure 13 (200 rpm, gas flow 20 and dm³·min⁻¹) and relevant examples in numerical simulation Figure 16, the worst bubble dispersion results were obtained because the dead zones were identified in the area near the bottom and sidewalls of the vessel, which disqualifies these work parameters for further use. The areas where swirls and gas bubble chains formed were identified only for the inert gas flows of 20 and 30 dm³·min⁻¹ and 200 rpm in the analyzed model (physical model). This means that the presented impeller model had the best performance in terms of dispersion of gas bubbles in the model liquid. The worst bubble dispersion results were obtained because the dead zones were identified in the area near the bottom and side walls of the vessel, which disqualifies these work parameters for further use.

Figure 17 presents exemplary results of model tests (CFD and physical model) with marked gas bubble dispersion zones. All variants of tests were analogously compared, and this comparison allowed validating the numerical model.

An external file that holds a picture, illustration, etc.
Object name is materials-15-05273-g017.jpg

Figure 17

Compilations of model research results (CFD and physical): A—single gas bubbles formed on the surface of the modeling liquid, B—excessive formation of gas chains and swirls, C—uniform distribution of gas bubbles in the entire volume of the tank, and D—dead zones without gas bubbles, no dispersion. (a) Variant B; (b) variant F.

It should be mentioned here that, in numerical simulations, it is necessary to make certain assumptions and simplifications. The calculations assumed three particle size classes (Table 2), which represent the different gas bubbles that form due to different gas flow rates. The maximum number of particles/bubbles (Table 1) generated was assumed in advance and related to the computational capabilities of the computer. Too many particles can also make it difficult to visualize and analyze the results. The size of the particles, of course, affects their behavior during simulation, while, in the figures provided in the article, the bubbles are represented by spheres (visualization of the results) of the same size. Please note that, due to the adopted Lagrangian–Eulerian approach, the simulation did not take into account phenomena such as bubble collapse or fusion. However, the obtained results allow a comprehensive analysis of the behavior of gas bubbles in the system under consideration.

The comparative analysis of the visualization (quantitative) results obtained with the water model and CFD simulations (see Figure 17) generated a sufficient agreement from the point of view of the trends. A precise quantitative evaluation is difficult to perform because of the lack of a refraction compensating system in the water model. Furthermore, in numerical simulations, it is not possible to determine the geometry of the forming gas bubbles and their interaction with each other as opposed to the visualization in the water model. The use of both research methods is complementary. Thus, a direct comparison of images obtained by the two methods requires appropriate interpretation. However, such an assessment gives the possibility to qualitatively determine the types of the present gas bubble dispersion, thus ultimately validating the CFD results with the water model.

A summary of the visualization results for impellers RT3, i.e., analysis of the occurring gas bubble dispersion types, is presented in Table 8.

Table 8

Summary of visualization results (impeller RT3)—different types of gas bubble dispersion.

No Exp.	A	B	C	D	E	F
Gas flow rate, dm³·min⁻¹	10	30
Impeller speed, rpm	200	300	500	200	300	500
Type of dispersion	Accurate	Uniform	Uniform/excessive	Minimal	Excessive	Excessive

Open in a separate window

Tests carried out for impeller RT3 confirmed the high efficiency of gas bubble distribution in the volume of the tested object at a low inert gas flow rate of 10 dm³·min⁻¹. The most optimal variant was variant B (300 rpm, 10 dm³·min⁻¹). However, the other variants A and C (gas flow rate 10 dm³·min⁻¹) seemed to be favorable for this type of impeller and are recommended for further testing. The above process parameters will be analyzed in detail in a quantitative analysis to be performed on the basis of the obtained efficiency curves of the degassing process (oxygen removal). This analysis will give an unambiguous answer as to which process parameters are the most optimal for this type of impeller; the results are planned for publication in the next article.

It should also be noted here that the high agreement between the results of numerical calculations and physical modelling prompts a conclusion that the proposed approach to the simulation of a degassing process which consists of a single-phase flow model with a free surface and a particle flow model is appropriate. The simulation results enable us to understand how the velocity field in the fluid is formed and to analyze the distribution of gas bubbles in the system. The simulations in Flow-3D software can, therefore, be useful for both the design of the impeller geometry and the selection of process parameters.

Go to:

4. Conclusions

The results of experiments carried out on the physical model of the device for the simulation of barbotage refining of aluminum revealed that the worst results in terms of distribution and dispersion of gas bubbles in the studied object were obtained for the black impellers variants B4, B8, and B12 (multi-orifice impellers—four, eight, and 12 outlet holes, respectively).

In this case, the control of flow, speed, and number of gas exit orifices did not improve the process efficiency, and the developed design did not meet the criteria for industrial tests. In the case of the ‘red triangle’ impeller (variant RT3), uniform gas bubble dispersion was achieved throughout the volume of the modeling fluid for most of the tested variants. The worst bubble dispersion results due to the occurrence of the so-called dead zones in the area near the bottom and sidewalls of the vessel were obtained for the flow variants of 20 dm³·min⁻¹ and 200 rpm and 30 dm³·min⁻¹ and 200 rpm. For the analyzed model, areas where swirls and gas bubble chains were formed were found only for the inert gas flow of 20 and 30 dm³·min⁻¹ and 200 rpm. The model impeller (variant RT3) had the best performance compared to the previously presented impellers in terms of dispersion of gas bubbles in the model liquid. Moreover, its design differed from previously presented models because of its sharp edges. This can be advantageous for gas bubble dispersion, but may negatively affect its suitability in industrial conditions due to premature wearing.

The CFD simulation results confirmed the results obtained from the experiments performed on the physical model. The numerical simulation of the operation of the ‘red triangle’ impeller model (using Flow-3D software) gave good agreement with the experiments performed on the physical model. This means that the presented model impeller, as compared to other (analyzed) designs, had the best performance in terms of gas bubble dispersion in the model liquid.

In further work, the developed numerical model is planned to be used for CFD simulations of the gas bubble distribution process taking into account physicochemical parameters of liquid aluminum based on industrial tests. Consequently, the obtained results may be implemented in production practice.

Go to:

Funding Statement

This paper was created with the financial support grants from the AGH-UST, Faculty of Foundry Engineering, Poland (16.16.170.654 and 11/990/BK_22/0083) for the Faculty of Materials Engineering, Silesian University of Technology, Poland.

Go to:

Author Contributions

Conceptualization, K.K. and D.K.; methodology, J.P. and T.M.; validation, M.S. and S.G.; formal analysis, D.K. and T.M.; investigation, J.P., K.K. and S.G.; resources, M.S., J.P. and K.K.; writing—original draft preparation, D.K. and T.M.; writing—review and editing, D.K. and T.M.; visualization, J.P., K.K. and S.G.; supervision, D.K.; funding acquisition, D.K. and T.M. All authors have read and agreed to the published version of the manuscript.

Go to:

Institutional Review Board Statement

Not applicable.

Go to:

Informed Consent Statement

Not applicable.

Go to:

Data Availability Statement

Data are contained within the article.

Go to:

Conflicts of Interest

The authors declare no conflict of interest.

Go to:

Footnotes

Publisher’s Note: MDPI stays neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Go to:

References

1. Zhang L., Xuewei L., Torgerson A.T., Long M. Removal of Impurity Elements from Molten Aluminium: A Review. Miner. Process. Extr. Metall. Rev. 2011;32:150–228. doi: 10.1080/08827508.2010.483396. [CrossRef] [Google Scholar]

2. Saternus M. Impurities of liquid aluminium-methods on their estimation and removal. Met. Form. 2015;23:115–132. [Google Scholar]

3. Żak P.L., Kalisz D., Lelito J., Gracz B., Szucki M., Suchy J.S. Modelling of non-metallic particle motion process in foundry alloys. Metalurgija. 2015;54:357–360. [Google Scholar]

4. Kalisz D., Kuglin K. Efficiency of aluminum oxide inclusions rmoval from liquid steel as a result of collisions and agglomeration on ceramic filters. Arch. Foundry Eng. 2020;20:43–48. [Google Scholar]

5. Kuglin K., Kalisz D. Evaluation of the usefulness of rotors for aluminium refining. IOP Conf. Ser. Mater. Sci. Eng. 2021;1178:012036. doi: 10.1088/1757-899X/1178/1/012036. [CrossRef] [Google Scholar]

6. Saternus M., Merder T. Physical modeling of the impeller construction impact o the aluminium refining process. Materials. 2022;15:575. doi: 10.3390/ma15020575. [PMC free article] [PubMed] [CrossRef] [Google Scholar]

7. Saternus M., Merder T. Physical modelling of aluminum refining process conducted in batch reactor with rotary impeller. Metals. 2018;8:726. doi: 10.3390/met8090726. [CrossRef] [Google Scholar]

8. Saternus M., Merder T., Pieprzyca J. The influence of impeller geometry on the gas bubbles dispersion in uro-200 reactor—RTD curves. Arch. Metall. Mater. 2015;60:2887–2893. doi: 10.1515/amm-2015-0461. [CrossRef] [Google Scholar]

9. Hernández-Hernández M., Camacho-Martínez J., González-Rivera C., Ramírez-Argáez M.A. Impeller design assisted by physical modeling and pilot plant trials. J. Mater. Process. Technol. 2016;236:1–8. doi: 10.1016/j.jmatprotec.2016.04.031. [CrossRef] [Google Scholar]

10. Mancilla E., Cruz-Méndez W., Garduño I.E., González-Rivera C., Ramírez-Argáez M.A., Ascanio G. Comparison of the hydrodynamic performance of rotor-injector devices in a water physical model of an aluminum degassing ladle. Chem. Eng. Res. Des. 2017;118:158–169. doi: 10.1016/j.cherd.2016.11.031. [CrossRef] [Google Scholar]

11. Michalek K., Socha L., Gryc K., Tkadleckova M., Saternus M., Pieprzyca J., Merder T. Modelling of technological parameters of aluminium melt refining in the ladle by blowing of inert gas through the rotating impeller. Arch. Metall. Mater. 2018;63:987–992. [Google Scholar]

12. Walek J., Michalek K., Tkadlecková M., Saternus M. Modelling of Technological Parameters of Aluminium Melt Refining in the Ladle by Blowing of Inert Gas through the Rotating Impeller. Metals. 2021;11:284. doi: 10.3390/met11020284. [CrossRef] [Google Scholar]

13. Michalek K., Gryc K., Moravka J. Physical modelling of bath homogenization in argon stirred ladle. Metalurgija. 2009;48:215–218. [Google Scholar]

14. Michalek K. The Use of Physical Modeling and Numerical Optimization for Metallurgical Processes. VSB; Ostrawa, Czech Republic: 2001. [Google Scholar]

15. Chen J., Zhao J. Light Metals. TMS; Warrendale, PA, USA: 1995. Bubble distribution in a melt treatment water model; pp. 1227–1231. [Google Scholar]

16. Saternus M. Model Matematyczny do Sterowania Procesem Rafinacji Ciekłych Stopów Aluminium Przy Zastosowaniu URO-200. Katowice, Poland: 2004. Research Project Nr 7 T08B 019 21. [Google Scholar]

17. Pietrewicz L., Wężyk W. Urządzenia do rafinacji gazowej typu URO-200 sześć lat produkcji i doświadczeń; Proceedings of the Aluminum Conference; Zakopane, Poland. 12–16 October 1998. [Google Scholar]

18. Flow3d User’s Guide. Flow Science, Inc.; Santa Fe, NM, USA: 2020. [Google Scholar]

19. Sinelnikov V., Szucki M., Merder T., Pieprzyca J., Kalisz D. Physical and numerical modeling of the slag splashing process. Materials. 2021;14:2289. doi: 10.3390/ma14092289. [PMC free article] [PubMed] [CrossRef] [Google Scholar]

20. White F. Fluid Mechanics. McGraw-Hill; New York, NY, USA: 2010. (McGraw-Hill Series in Mechanical Engineering). [Google Scholar]

21. Yang Z., Yang L., Cheng T., Chen F., Zheng F., Wang S., Guo Y. Fluid Flow Characteristic of EAF Molten Steel with Different Bottom-Blowing Gas Flow Rate Distributions. ISIJ. 2020;60:1957–1967. doi: 10.2355/isijinternational.ISIJINT-2019-794. [CrossRef] [Google Scholar]

22. Nichols B.D., Hirt C.W. Methods for calculating multi-dimensional, transient free surface flows past bodies; Proceedings of the First International Conference on Numerical Ship Hydrodynamics; Gaithersburg, MD, USA. 20–22 October 1975. [Google Scholar]

23. Hirt C.W., Nichols B.D. Volume of Fluid (VOF) Method for the Dynamics of Free Boundaries. J. Comput. Phys. 1981;39:201–255. doi: 10.1016/0021-9991(81)90145-5. [CrossRef] [Google Scholar]

24. Szucki M., Suchy J.S., Lelito J., Malinowski P., Sobczyk J. Application of the lattice Boltzmann method for simulation of the mold filling process in the casting industry. Heat Mass Transf. 2017;53:3421–3431. doi: 10.1007/s00231-017-2069-5. [CrossRef] [Google Scholar]

25. Themelis N.J., Goyal P. Gas injection in steelmaking. Candian Metall. Trans. 1983;22:313–320. [Google Scholar]

26. Zhang L., Jing X., Li Y., Xu Z., Cai K. Mathematical model of decarburization of ultralow carbon steel during RH treatment. J. Univ. Sci. Technol. Beijing. 1997;4:19–23. [Google Scholar]

27. Chiti F., Paglianti A., Bujalshi W. A mechanistic model to estimate powder consumption and mixing time in aluminium industries. Chem. Eng. Res. Des. 2004;82:1105–1111. doi: 10.1205/cerd.82.9.1105.44156. [CrossRef] [Google Scholar]

28. Bouaifi M., Roustan M. Power consumption, mixing time and homogenization energy in dual-impeller agitated gas-liquid reactors. Chem. Eng. Process. 2011;40:87–95. doi: 10.1016/S0255-2701(00)00128-8. [CrossRef] [Google Scholar]

29. Kang J., Lee C.H., Haam S., Koo K.K., Kim W.S. Studies on the overall oxygen transfer rate and mixing time in pilot-scale surface aeration vessel. Environ. Technol. 2001;22:1055–1068. doi: 10.1080/09593332208618215. [PubMed] [CrossRef] [Google Scholar]

30. Moucha T., Linek V., Prokopov E. Gas hold-up, mixing time and gas-liquid volumetric mass transfer coefficient of various multiple-impeller configurations: Rushton turbine, pitched blade and techmix impeller and their combinations. Chem. Eng. Sci. 2003;58:1839–1846. doi: 10.1016/S0009-2509(02)00682-6. [CrossRef] [Google Scholar]

31. Szekely J. Flow phenomena, mixing and mass transfer in argon-stirred ladles. Ironmak. Steelmak. 1979;6:285–293. [Google Scholar]

32. Iguchi M., Nakamura K., Tsujino R. Mixing time and fluid flow phenomena in liquids of varying kinematic viscosities agitated by bottom gas injection. Metall. Mat. Trans. 1998;29:569–575. doi: 10.1007/s11663-998-0091-1. [CrossRef] [Google Scholar]

33. Hjelle O., Engh T.A., Rasch B. Removal of Sodium from Aluminiummagnesium Alloys by Purging with Cl₂. Aluminium-Verlag GmbH; Dusseldorf, Germany: 1985. pp. 343–360. [Google Scholar]

34. Zhang L., Taniguchi S. Fundamentals of inclusion removal from liquid steel by bubble flotation. Int. Mat. Rev. 2000;45:59–82. doi: 10.1179/095066000101528313. [CrossRef] [Google Scholar]

원문 보기

Development of macro-defect-free PBF-EB-processed Ti–6Al–4V alloys with superior plasticity using PREP-synthesized powder and machine learning-assisted process optimization

Yunwei Gui^abKenta Aoyagi^bAkihiko Chiba^b
^aDepartment of Materials Processing, Graduate School of Engineering, Tohoku University, 6-6 Aramaki Aza Aoba, Aoba-ku, Sendai, 980-8579, Japan
^bInstitute for Materials Research, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai, 980-8577, Japan

Received 14 October 2022, Revised 23 December 2022, Accepted 3 January 2023, Available online 5 January 2023.Show lessAdd to MendeleyShareCite

https://doi.org/10.1016/j.msea.2023.144595 Get rights and content

Abstract

The elimination of internal macro-defects is a key issue in Ti–6Al–4V alloys fabricated via powder bed fusion using electron beams (PBF-EB), wherein internal macro-defects mainly originate from the virgin powder and inappropriate printing parameters. This study compares different types powders by combining support vector machine techniques to determine the most suitable powder for PBF-EB and to predict the processing window for the printing parameters without internal macro-defects. The results show that powders fabricated via plasma rotating electrode process have the best sphericity, flowability, and minimal porosity and are most suitable for printing. Surface roughness criterion was also applied to determine the quality of the even surfaces, and support vector machine was used to construct processing maps capable of predicting a wide range of four-dimensional printing parameters to obtain macro-defect-free samples, offering the possibility of subsequent development of Ti–6Al–4V alloys with excellent properties. The macro-defect-free samples exhibited good elongation, with the best overall mechanical properties being the ultimate tensile strength and elongation of 934.7 MPa and 24.3%, respectively. The elongation of the three macro-defect-free samples was much higher than that previously reported for additively manufactured Ti–6Al–4V alloys. The high elongation of the samples in this work is mainly attributed to the elimination of internal macro-defects.

Introduction

Additive manufacturing (AM) technologies can rapidly manufacture complex or custom parts, reducing process steps and saving manufacturing time [[1], [2], [3], [4]], and are widely used in the aerospace, automotive, and other precision industries [5,6]. Powder bed fusion using an electron beam (PBF-EB) is an additive manufacturing method that uses a high-energy electron beam to melt metal powders layer by layer to produce parts. In contrast to selective laser melting, PBF-EB involves the preparation of samples in a high vacuum environment, which effectively prevents the introduction of impurities such as O and N. It also involves a preheating process for the print substrate and powder, which reduces residual thermal stress on the sample and subsequent heat treatment processes [[2], [3], [4],7]. Due to these features and advantages, PBF-EB technology is a very important AM technology with great potential in metallic materials. Moreover, PBF-EB is the ideal AM technology for the manufacture of complex components made of many alloys, such as titanium alloys, nickel-based superalloys, aluminum alloys and stainless steels [[2], [3], [4],8].

Ti–6Al–4V alloy is one of the prevalent commercial titanium alloys possessing high specific strength, excellent mechanical properties, excellent corrosion resistance, and good biocompatibility [9,10]. It is widely used in applications requiring low density and excellent corrosion resistance, such as the aerospace industry and biomechanical applications [11,12]. The mechanical properties of PBF-EB-processed Ti–6Al–4V alloys are superior to those fabricated by casting or forging, because the rapid cooling rate in PBF-EB results in finer grains [[12], [13], [14], [15], [16], [17], [18]]. However, the PBF-EB-fabricated parts often include internal macro-defects, which compromises their mechanical properties [[19], [20], [21], [22]]. This study focused on the elimination of macro-defects, such as porosity, lack of fusion, incomplete penetration and unmelted powders, which distinguishes them from micro-defects such as vacancies, dislocations, grain boundaries and secondary phases, etc. Large-sized fusion defects cause a severe reduction in mechanical strength. Smaller defects, such as pores and cracks, lead to the initiation of fatigue cracking and rapidly accelerate the cracking process [23]. The issue of internal macro-defects must be addressed to expand the application of the PBF-EB technology. The main studies for controlling internal macro-defects are online monitoring of defects, remelting and hot isostatic pressing (HIP). The literatures [24,25] report the use of infrared imaging or other imaging techniques to identify defects, but the monitoring of smaller sized defects is still not adequate. And in some cases remelting does not reduce the internal macro-defects of the part, but instead causes coarsening of the macrostructure and volatilization of some metal elements [23]. The HIP treatment does not completely eliminate the internal macro-defects, the original defect location may still act as a point of origin of the crack, and the subsequent treatment will consume more time and economic costs [23]. Therefore, optimizing suitable printing parameters to avoid internal macro-defects in printed parts at source is of great industrial value and research significance, and is an urgent issue in PBF-EB related technology.

There are two causes of internal macro-defects in the AM process: gas pores trapped in the virgin powder and the inappropriate printing parameters [7,23]. Gui et al. [26] classify internal macro-defects during PBF-EB process according to their shape, such as spherical defects, elongated shape defects, flat shape defects and other irregular shape defects. Of these, spherical defects mainly originate from raw material powders. Other shape defects mainly originate from lack of fusion or unmelted powders caused by unsuitable printing parameters, etc. The PBF-EB process requires powders with good flowability, and spherical powders are typically chosen as raw materials. The prevalent techniques for the fabrication of pre-alloyed powders are gas atomization (GA), plasma atomization (PA), and the plasma rotating electrode process (PREP) [27,28]. These methods yield powders with different characteristics that affect the subsequent fabrication. The selection of a suitable powder for PBF-EB is particularly important to produce Ti–6Al–4V alloys without internal macro-defects. The need to optimize several printing parameters such as beam current, scan speed, line offset, and focus offset make it difficult to eliminate internal macro-defects that occur during printing [23]. Most of the studies [11,12,22,[29], [30], [31], [32], [33]] on the optimization of AM processes for Ti–6Al–4V alloys have focused on samples with a limited set of parameters (e.g., power–scan speed) and do not allow for the guidance and development of unknown process windows for macro-defect-free samples. In addition, process optimization remains a time-consuming problem, with the traditional ‘trial and error’ method demanding considerable time and economic costs. The development of a simple and efficient method to predict the processing window for alloys without internal macro-defects is a key issue. In recent years, machine learning techniques have increasingly been used in the field of additive manufacturing and materials development [[34], [35], [36], [37]]. Aoyagi et al. [38] recently proposed a novel and efficient method based on a support vector machine (SVM) to optimize the two-dimensional process parameters (current and scan speed) and obtain PBF-EB-processed CoCr alloys without internal macro-defects. The method is one of the potential approaches toward effective optimization of more than two process parameters and makes it possible for the machine learning techniques to accelerate the development of alloys without internal macro-defects.

Herein, we focus on the elimination of internal macro-defects, such as pores, lack of fusion, etc., caused by raw powders and printing parameters. The Ti–6Al–4V powders produced by three different methods were compared, and the powder with the best sphericity, flowability, and minimal porosity was selected as the feedstock for subsequent printing. The relationship between the surface roughness and internal macro-defects in the Ti–6Al–4V components was also investigated. The combination of SVM and surface roughness indices (Sdr) predicted a wider four-dimensional processing window for obtaining Ti–6Al–4V alloys without internal macro-defects. Finally, we investigated the tensile properties of Ti–6Al–4V alloys at room temperature with different printing parameters, as well as the corresponding microstructures and fracture types.

Section snippets

Starting materials

Three types of Ti–6Al–4V alloy powders, produced by GA, PA, and PREP, were compared. The particle size distribution of the powders was determined using a laser particle size analyzer (LS230, Beckman Coulter, USA), and the flowability was measured using a Hall flowmeter (JIS-Z2502, Tsutsui Scientific Instruments Co., Ltd., Japan), according to the ASTM B213 standard. The powder morphology and internal macro-defects were determined using scanning electron microscopy (SEM, JEOL JCM-6000) and X-ray

Comparison of the characteristics of GA, PA, and PREP Ti–6Al–4V powders

The particle size distributions (PSDs) and flowability of the three types of Ti–6Al–4V alloy powders produced by GA, PA, and PREP are shown in Fig. 2. Although the average particle sizes are similar (89.4 μm for GA, 82.5 μm for PA, and 86.1μm for PREP), the particle size range is different for the three types of powder (6.2–174.8 μm for GA, 27.3–139.2 μm for PA, and 39.4–133.9 μm for PREP). The flowability of the GA, PA, and PREP powders was 30.25 ± 0.98, 26.54 ± 0.37, and 25.03 ± 0.22 (s/50

Conclusions

The characteristics of the three types of Ti–6Al–4V alloy powders produced via GA, PA, and PREP were compared. The PREP powder with the best sphericity, flowability, and low porosity was found to be the most favorable powder for subsequent printing of Ti–6Al–4V alloys without internal macro-defects. The quantitative criterion of Sdr <0.015 for even surfaces was also found to be applicable to Ti–6Al–4V alloys. The process maps of Ti–6Al–4V alloys include two regions, high beam current/scan speed

Uncited references

[55]; [56]; [57]; [58]; [59]; [60]; [61]; [62]; [63]; [64]; [65].

CRediT authorship contribution statement

Yunwei Gui: Writing – original draft, Visualization, Validation, Investigation. Kenta Aoyagi: Writing – review & editing, Supervision, Resources, Methodology, Funding acquisition, Conceptualization. Akihiko Chiba: Supervision, Funding acquisition.

Declaration of competing interest

The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper.

Acknowledgments

This study was based on the results obtained from project JPNP19007, commissioned by the New Energy and Industrial Technology Development Organization (NEDO). This work was also supported by JSPS KAKENHI (Proposal No. 21K03801) and the Inter-University Cooperative Research Program (Proposal nos. 18G0418, 19G0411, and 20G0418) of the Cooperative Research and Development Center for Advanced Materials, Institute for Materials Research, Tohoku University. It was also supported by the Council for

References (65)

P. Edwards et al.Fatigue performance evaluation of selective laser melted Ti-6Al-4VMater. Sci. Eng.(2014)
S. Leuders et al.On the mechanical behaviour of titanium alloy TiAl6V4 manufactured by selective laser melting: fatigue resistance and crack growth performanceInt. J. Fatig.(2013)
D.A. Hollander et al.Structural, mechanical and in vitro characterization of individually structured Ti-6Al-4V produced by direct laser formingBiomaterials(2006)
B.E. Carroll et al.Anisotropic tensile behavior of Ti-6Al-4V components fabricated with directed energy deposition additive manufacturingActa Mater.(2015)
Y. Zhai et al.Microstructure, static properties, and fatigue crack growth mechanisms in Ti-6Al-4V fabricated by additive manufacturing: LENS and EBMEng. Fail. Anal.(2016)
S.L. Lu et al.Massive transformation in Ti-6Al-4V additively manufactured by selective electron beam meltingActa Mater.(2016)
Y. Zhao et al.Manipulating local heat accumulation towards controlled quality and microstructure of a Co-Cr-Mo alloy in powder bed fusion with electron beamMater. Lett.(2019)
X. Huang et al.Indefinite kernels in least squares support vector machines and principal component analysisAppl. Comput. Harmon. Anal.(2017)
Y. Cui et al.Effects of plasma rotating electrode process parameters on the particle size distribution and microstructure of Ti-6Al-4 V alloy powderPowder Technol.(2020)
Y. Zhao et al.Molten pool behavior and effect of fluid flow on solidification conditions in selective electron beam melting (SEBM) of a biomedical Co-Cr-Mo alloyAddit. Manuf.(2019)

View more references

Cited by (0)

Effect of tailwater depth on non-cohesive earth dam failure due to overtopping

범람으로 인한 비점착성 흙댐 붕괴에 대한 테일워터 깊이의 영향

ShaimaaAman^aMohamedAbdelrazek Rezk^bRabieaNasr^c

Abstract

본 연구에서는 범람으로 인한 토사댐 붕괴에 대한 테일워터 깊이의 영향을 실험적으로 조사하였다. 테일워터 깊이의 네 가지 다른 값을 검사합니다. 각 실험에 대해 댐 수심 측량 프로파일의 진화, 고장 기간, 침식 체적 및 유출 수위곡선을 관찰하고 기록합니다.

결과는 tailwater 깊이를 늘리면 고장 시간이 최대 57% 감소하고 상대적으로 침식된 마루 높이가 최대 77.6% 감소한다는 것을 보여줍니다. 또한 상대 배수 깊이가 3, 4, 5인 경우 누적 침식 체적의 감소는 각각 23, 36.5 및 75%인 반면 최대 유출량의 감소는 각각 7, 14 및 17.35%입니다.

실험 결과는 침식 과정을 복제할 때 Flow 3D 소프트웨어의 성능을 평가하는 데 활용됩니다. 수치 모델은 비응집성 흙댐의 침식 과정을 성공적으로 시뮬레이션합니다.

The influence of tailwater depth on earth dam failure due to overtopping is investigated experimentally in this work. Four different values of tailwater depths are examined. For each experiment, the evolution of the dam bathymetry profile, the duration of failure, the eroded volume, and the outflow hydrograph are observed and recorded. The results reveal that increasing the tailwater depth reduces the time of failure by up to 57% and decreases the relative eroded crest height by up to 77.6%. In addition, for relative tailwater depths equal to 3, 4, and 5, the reduction in the cumulative eroded volume is 23, 36.5, and 75%, while the reduction in peak discharge is 7, 14, and 17.35%, respectively. The experimental results are utilized to evaluate the performance of the Flow 3D software in replicating the erosion process. The numerical model successfully simulates the erosion process of non-cohesive earth dams.

Keywords

Earth dam, Eroded volume, Flow 3D model, Non-cohesive soil, Overtopping failure, Tailwater depth

Notation

d₅₀

Mean partical diameterW_c

Optimum water contentZ_o

Dam height (cm)d_o

Tailwater depth (cm)Z_eroded

Eroded height of the dam measured at distance of 0.7 m from the dam heel (cm)t

Total time of failure (sec)t₁

Time of crest width erosion (sec)Z_crest

The crest height (cm)V_total

Total volume of the dam (m³)V_eroded

Cumulative eroded volume (m³)RMSE

The statistical variable root- mean- square errord

Degree of agreement indexy_u.s.

The upstream water depth (cm)y_d.s

The downstream water depth (cm)H

Water surface elevation over sharp crested weir (cm)Q

Outflow discharge (liter/sec)Q_peak

Peak discharge (liter/sec)

1. Introduction

Earth dams are compacted structures composed of natural materials that are usually mined or quarried from local locations. The failures of the earth dams have proven to be deadly, destructive, and costly. According to People’s Daily, two earthen dams, Yong’an Dam and Xinfa Dam located in Hulun Buir City in North China’s Inner Mongolia failed on 2021, due to a surge in the water level of the Nuomin River caused by heavy rain. The dam breach affected 16,660 people, flooded 325,622 mu of farmland (21708.1 ha), and destroyed 22 bridges, 124 culverts, and 15.6 km of roadways. Also, the failure of south fork dam (earth and rock fill dam) near Johnstown on 1889 is considered the worst U.S dam disaster in terms of loss of life. The dam was overtopped and washed away due to unexpected heavy rains, releasing 20 million tons of water which destroyed Johnstown and resulted in 2209 deaths, [1], [2]. Piping or shear sliding, failure due to natural factors, and failure due to overtopping are all possible causes of earth dam failure. However, overtopping failure is the most frequent cause of dam failure. According to The International Committee on Large Dams (ICOLD, 1995), and [3], more than one-third of the total known dam failures were caused by dam overtopping.

Overtopping occurs as the result of insufficient flood design or freeboard in some cases. Extreme rainstorms can cause floods which can overtop the dam and cause it to fail. The size and geometry of the reservoir or the dam (side slopes, top width, height, etc.), the homogeneity of the material used in the construction of the dam, overtopping depth, and the presence or absence of tailwater are all elements that influence this type of failure which will be illustrated in the following literature. Overtopping failures of earth dams may be divided into several failure mechanisms based on the material composition and the inner structure of the dam. For cohesive earth dams because of low permeability, no seepage exists on the slopes. Erosion often begins at the earth dam toe during turbulent erosion and moves upstream, undercutting the slope, causing the removal of large chunks of materials. While for non-cohesive earth dams the downstream face of the dam flattens progressively and is often said to rotate around a point near the downstream toe [4], [5], [6] In the last few decades, the study of failures due to overtopping has gained popularity among researchers. The overtopping failure, in fact, has been widely investigated in coastal and river hydraulics and morpho dynamic. In addition, several laboratory experimental studies have been conducted in this field in order to better understand different involved factors. Also, many numerical types of research have been conducted to investigate the process of overtopping failure as well as the elements that influence this type of failure.

Tabrizi et al. [5] conducted a series of embankment overtopping tests to find the effect of compaction on the failure of a homogenous sand embankment. A plane breach process occurred across the flume width due to the narrow flume width. They measured the downstream hydrographs and embankment surface profile for every case. They concluded that the peak discharge decreased with a high compaction level, while the time to peak increased. Kansoh et al. [6] studied experimentally the failure of compacted homogeneous non-cohesive earthen embankment due to overtopping. They investigated the influence of different shape parameters including the downstream slope, the crest width, and the height of the embankment on the erosion process. The erosion process was initiated by carving a pilot channel into the embankment crest. They evaluated the time of embankment failure for different shape parameters. They concluded that the failure time increases with increasing the downstream slope and the crest width. Zhu et al. [7] investigated experimentally the breaching of five embankments, one constructed with pure sand, and four with different sand-silt–clay mixtures. The erosion pattern was similar across the flume width. They stated that for cohesive soil mixtures the head cut erosion was the most important factor that affected the breach growth, while for non-cohesive soil the breach erosion was affected by shear erosion.

Amaral et al. [8] studied experimentally the failure by overtopping for two embankments built from silt sand material. They studied the effect of the degree of compaction of the embankment and the geometry of the pilot channel carved at the centre of the dam crest. They studied two shapes of pilot channel a rectangular shape and triangular shape. They stated that the breach development is influenced by a higher degree of compaction, however, the pilot channel geometry did not influence the breach’s final form. Bereta et al. [9] studied experimentally the breach formation of five dam models, three of them were homogenous clay soil while two were sandy-clay mixtures. The erosion process was initiated by cutting a pilot channel at the centre of the dam crest. They observed the initiation of erosion, flow shear erosion, sidewall bottom erosion, and distinguished the soil mechanical slope mass failure from the head cut vertically and laterally during these tests. Verma et al. [10] investigated experimentally a two-dimensional erosion phenomenon due to overtopping by using a wooden fuse plug model and five different soils. They concluded that the erosion process was affected mostly by cohesiveness and degree of compaction. For cohesive soils, a head cut erosion was observed, while for non-cohesive soils surface erosion occurred gradually. Also, the dimensions of fuse plug, type of fill material, reservoir capacity, and inflow were found to affect the behaviour of the overall breaching process.

Wu and Qin [11] studied the effect of adding coarse grains to the downstream face of a non-cohesive dam as a result of tailings deposition. The process of overtopping during tailings dam failures is analyzed and its effect on delaying the dam-break process and disaster mitigation are investigated. They found that the tested protective measures decreased the breach area, the maximum breaching flow discharge and flow velocity, and the downstream inundated area. Khankandi et al. [12] studied experimentally the effect of reservoir geometry on dam break flow in case of dry and wet bed conditions. They considered four different reservoir shapes, a long reservoir, a wide, a trapezoidal shaped and one with a 90◦ bend all with identical water volume and horizontal bed. The dam break is simulated by the sudden gate removal using a pneumatic jack. They measured the variation of water level over time with ultrasonic sensors and flow velocity component with an acoustic Doppler velocimeter. Also, the experimental results of water level variation are compared with Ritters solution (1892) [13]. They stated that for dry bed condition the long and 90 bend reservoirs results are close to the analytical solution by ritter also in these two shapes a 1D flow is noticed. However, for wide and trapezoidal reservoirs a 2D effect is significant due to flow contraction at channel entrance.

Rifai et al. [14] conducted a series of experiments to investigate the effect of tailwater depth on the outflow discharge and breach geometry during non-cohesive homogenous fluvial dikes overtopping failure. They cut an initial notch in the crest at 0.8 m from the upstream end of the dike to initiate overtopping. They compared their results to previous experiments under different main channel inflow discharges combined with a free floodplain. They divided the dike breaching process into three stages: gradual start of overtopping flow resulting in slow initiation of dike erosion, deepening and widening breach due to large flow depth and velocity, finally the flow depth starts stabilizing at its minimal level with or without sustained breach expansion. They stated that breach discharge has lower values than in free floodplain tests. Jiang [15] studied the effect of bed slope on breach parameters and peak discharge in non-cohesive embankment failure. An initial triangular breach with a depth and width of 4 cm was pre-set on one side of the dam. He stated that peak discharge increases with the increase of bed slope and then decreases.

Ozmen-cagatay et al. [16] studied experimentally flood wave propagation resulted from a sudden dam break event. For dam-break modelling, they used a mechanism that permitted the rapid removal of a vertical plate with a thickness of 4 mm and made of rigid plastic. They conducted three tests, one with dry bed condition and two tests with tailwater depths equal 0.025 m and 0.1 m respectively. They recorded the free surface profile during initial stages of dam break by using digital image processing. Finally, they compared the experimental results with the with a commercially available VOF-based CFD program solving the Reynolds-averaged Navier –Stokes equations (RANS) with the k– Ɛ turbulence model and the shallow water equations (SWEs). They concluded that Wave breaking was delayed with increasing the tailwater depth to initial reservoir depth ratio. They also stated that the SWE approach is sufficient more to represent dam break flows for wet bed condition. Evangelista [17] investigated experimentally and numerically using a depth-integrated two-phase model, the erosion of sand dike caused by the impact of a dam break wave. The dam break is simulated by a sudden opening of an upstream reservoir gate resulting in the overtopping of a downstream trapezoidal sand dike. The evolution of the water wave caused from the gate opening and dike erosion process are recorded by using a computer-controlled camera. The experimental results demonstrated that the progression of the wave front and dike erosion have a considerable influence on each other during the process. In addition, the dike constructed from fine sands was more resistant to erosion than the one built with coarse sand. They also stated that the numerical model can is capable of accurately predicting wave front position and dike erosion. Also, Di Cristo et al. [18] studied the effect of dam break wave propagation on a sand embankment both experimentally and numerically using a two-phase shallow-water model. The evolution of free surface and of the embankment bottom are recorded and used in numerical model assessment. They stated that the model allows reasonable simulation of the experimental trends of the free surface elevation regardeless of the geofailure operator.

Lots of numerical models have been developed over the past few years to simulate the dam break flooding problem. A one-dimensional model, such as Hec-Ras, DAMBRK and MIKE 11, ect. A two-dimensional model such as iRIC Nay2DH is used in earth embankment breach simulation. Other researchers studied the failure process numerically using (3D) computational fluid dynamics (CFD) models, such as FLOW-3D, and FLUENT. Goharnejad et al. [19] determined the outflow hydrograph which results from the embankment dam break due to overtopping. Hu et al. [20] performed a comparison between Flow-3D and MIKE3 FM numerical models in simulating a dam break event under dry and wet bed conditions with different tailwater depths. Kaurav et al. [21] simulated a planar dam breach process due to overtopping. They conducted a sensitivity analysis to find the effect of dam material, dam height, downstream slope, crest width, and inlet discharge on the erosion process and peak discharge through breach. They concluded that downstream slope has a significant influence on breaching process. Yusof et al. [22] studied the effect of embankment sediment sizes and inflow rates on breaching geometric and hydrodynamic parameters. They stated that the peak outflow hydrograph increases with increasing sediment size and inflow rates while time of failure decreases.

In the present work, the effect of tailwater depth on earth dam failure during overtopping is studied experimentally. The relation between the eroded volume of the dam and the tailwater depth is presented. Also, the percentage of reduction in peak discharge due to tailwater existence is calculated. An assessment of Flow 3D software performance in simulating the erosion process during earth dam failure is introduced. The statistical variable root- mean- square error, RMSE, and the agreement degree index, d, are used in model assessment.

2. Material and methods

The tests are conducted in a straight rectangular flume in the laboratory of Irrigation Engineering and Hydraulics Department, Faculty of Engineering, Alexandria University, Egypt. The flume dimensions are 10 m long, 0.86 m wide, and 0.5 m deep. The front part of the flume is connected to a storage basin 1 m long by 0.86 m wide. The storage basin is connected to a collecting tank for water recirculation during the experiments as shown in Fig. 1, Fig. 2. A sharp-crested weir is placed at a distance of 4 m downstream the constructed dam to keep a constant tailwater depth in each experiment and to measure the outflow discharge.

To measure the eroded volume with time a rods technique is used. This technique consists of two parallel wooden plates with 10 cm distance in between and five rows of stainless-steel rods passing vertically through the wooden plates at a spacing of 20 cm distributed across flume width. Each row consists of four rods with 15 cm spacing between them. Also, a graph board is provided to measure the drop in each rod with time as shown in Fig. 3, Fig. 4. After dam construction the rods are carefully rested on the dam, with the first line of rods resting in the middle of the dam crest and then a constant distance of 15 cm between rods lines is maintained.

A soil sample is taken and tested in the laboratory of the soil mechanics to find the soil geotechnical parameters. The soil particle size distribution is also determined by sieve analysis as shown in Fig. 5. The soil mean diameter d₅₀,equals 0.38 mm and internal friction angle equals 32.6°.

2.1. Experimental procedures

To investigate the effect of the tailwater depth (d_o), the tailwater depth is changed four times 5, 15, 20, and 25 cm on the sand dam model. The dam profile is 35 cm height, with crest width = 15 cm, the dam base width is 155 cm, and the upstream and downstream slopes are 2:1 as shown in Fig. 6. The dam dimensions are set as the flume permitted to allow observation of the dam erosion process under the available flume dimensions and conditions. All of the conducted experiments have the same dimensions and configurations.

The optimum water content, W_c, from the standard proctor test is found to be 8 % and the maximum dry unit weight is 19.42 kN/m³. The soil and water are mixed thoroughly to ensure consistency and then placed on three horizontal layers. Each layer is compacted according to ASTM standard with 25 blows by using a rammer (27 cm × 20.5 cm) weighing 4 kg. Special attention is paid to the compaction of the soil to guarantee the repeatability of the tests.

After placing and compacting the three layers, the dam slopes are trimmed carefully to form the trapezoidal shape of the dam. A small triangular pilot channel with 1 cm height and 1:1 side slopes is cut into the dam crest to initiate the erosion process. The position of triangular pilot channel is presented in Fig. 1. Three digital video cameras with a resolution of 1920 × 1080 pixels and a frame rate of 60 fps are placed in three different locations. One camera on one side of the flume to record the progress of the dam profile during erosion. Another to track the water level over the sharp-crested rectangular weir placed at the downstream end of the flume. And the third camera is placed above the flume at the downstream side of the dam and in front of the rods to record the drop of the tip of the rods with time as shown previously in Fig. 1.

Before starting the experiment, the water is pumped into the storage basin by using pump with capacity 360 m³/hr, and then into the upstream section of the flume. The upstream boundary is an inflow condition. The flow discharge provided to the storage basin is kept at a constant rate of 6 L/sec for all experiments, while the downstream boundary is an outflow boundary condition.

Also, the required tailwater depth for each experiment is filled to the desired depth. A dye container valve is opened to color the water upstream of the dam to make it easy to distinguish the dam profile from the water profile. A wooden board is placed just upstream of the dam to prevent water from overtopping the dam until the water level rises to a certain level above the dam crest and then the wooden board is removed slowly to start the experiment.

2.2. Repeatability

To verify the accuracy of the results, each experiment is repeated two times under the same conditions. Fig. 7 shows the relative eroded crest height, Z_eroded / Z_o, with time for 5 cm tailwater depth. From the Figure, it can be noticed that results for all runs are consistent, and accuracy is achieved.

3. Numerical model

The commercially available numerical model, Flow 3D is used to simulate the dam failure due to overtopping for the cases of 15 cm, 20 cm and 25 cm tailwater depths. For numerical model calibration, experimental results for dam surface evolution are used. The numerical model is calibrated for selection of the optimal turbulence model (RNG, K-e, and k-w) and sediment scour equations (Van Rin, Meyer- peter and Muller, and Nielsen) that produce the best results. In this, the flow field is solved by the RNG turbulence model, and the van Rijn equation is used for the sediment scour model. A geometry file is imported before applying the mesh.

A Mesh sensitivity is analyzed and checked for various cell sizes, and it is found that decreasing the cell size significantly increases the simulation time with insignificant differences in the result. It is noticed that the most important factor influencing cell size selection is the value of the dam’s upstream and downstream slopes. For example, the slopes in the dam model are 2:1, thus the cell size ratio in X and Z directions should be 2:1 as well. The cell size in a mesh block is set to be 0.02 m, 0.025 m, and 0.01 m in X, Y and Z directions respectively.

In the numerical computations, the boundary conditions employed are the walls for sidewalls and the channel bottom. The pressure boundary condition is applied at the top, at the air–water interface, to account for atmospheric pressure on the free surface. The upstream boundary is volume flow rate while the downstream boundary is outflow discharge.

The initial condition is a fluid region, which is used to define fluid areas both upstream and downstream of the dam. To assess the model accuracy, the statistical variable root- mean- square error, RMSE, and the agreement degree index, d, are calculated as(1)RMSE=1N∑i=1N(Pi-Mi)2(2)d=1-∑Mi-Pi2∑Mi-M¯+Pi-P¯2

where N is the number of samples, P_i and M_i are the models and experimental values, P and M are the means of the model and experimental values. The best fit between the experimental and model results would have an RMSE = 0 and degree of agreement, d = 1.

4. Results of experimental work

The results of the total time of failure, t (defined as the time from when the water begins to overtop the dam crest until the erosion reaches a steady state, when no erosion occurs), time of crest width erosion t₁, cumulative eroded volume V_eroded, and peak discharge Q_peak for each experiment are listed in Table 1. The case of 5 cm tailwater depth is considered as a reference case in this work.

Table 1. Results of experimental work.

*Tailwater depth, d_o* (cm)**	*Total time of failure, t (sec)*	*Time of crest width erosion, t₁ (sec)*	*cumulative eroded volume, V_eroded* (m³)**	*Peak discharge, Q_peak* (liter/sec)**
5	255	22	0.21	13.12
15	165	30	0.16	12.19
20	140	34	0.13	11.29
25	110	39	0.05	10.84

5. Discussion

5.1. Side erosion

The evolution of the bathymetry of the erosion line recorded by the video camera1. The videos are split into frames (60 frames/sec) by the Free Video to JPG Converter v.5.063 build and then converted into an excel spreadsheet using MATLAB code as shown in Fig. 8.

Fig. 9 shows a sample of numerical model output. Fig. 10, Fig. 11, Fig. 12 show a dam profile development for different time steps from both experimental and numerical model, for tailwater depths equal 15 cm, 20 cm and 25 cm. Also, the values of RMSE and d for each figure are presented. The comparison shows that the Flow 3D software can simulate the erosion process of non-cohesive earth dam during overtopping with an RMSE value equals 0.023, 0.0218, and 0.0167 and degree of agreement, d, equals 0.95, 0.968, and 0.988 for relative tailwater depths, d_o/(d_o)_ref, = 3, 4 and 5, respectively. The low values of RMSE and high values of d show that the Flow 3D can effectively simulate the erosion process. From Fig. 10, Fig. 11, Fig. 12, it can be noticed that the model is not capable of reproducing the head cut, while it can simulate well the degradation of the crest height with a minor difference from experimental work. The reason of this could be due to inability of simulation of all physical conditions which exists in the experimental work, such as channel friction and the grain size distribution of the dam soil which is surely has a great effect on the erosion process and breach development. In the experimental work the grain size distribution is shown in Fig. 5, while the numerical model considers that the soil is uniform and exactly 50 % of the dam particles diameter are equal to the d₅₀ value. Another reason is that the model is not considering the increased resistance of the dam due to the apparent cohesion which happens due to dam saturation [23].

It is clear from both the experimental and numerical results that for a 5 cm tailwater depth, d_o/(d_o)_ref = 1.0, erosion begins near the dam toe and continues upward on the downstream slope until it reaches the crest. After eroding the crest width, the crest is lowered, resulting in increased flow rates and the speeding up of the erosion process. While for relative tailwater depths, d_o/(d_o)_ref = 3, 4, and 5 erosion starts at the point of intersection between the downstream slope and tailwater. The existence of tailwater works as an energy dissipater for the falling water which reduces the erosion process and prevents the dam from failure as shown in Fig. 13. It is found that the time of the failure decreases with increasing the tailwater depth because most of the dam height is being submerged with water which decreases the erosion process. The reduction in time of failure from the referenced case is found to be 35.3, 45, and 57 % for relative tailwater depth, d_o /(d_o)_ref equals 3, 4, and 5, respectively.

The relation between the relative eroded crest height, Z_eroded /Z_o, with time is drawn as shown in Fig. 14. It is found that the relative eroded crest height decreases with increasing tailwater depth by 10, 41, and 77.6 % for relative tailwater depth, d_o /(d_o)_ref equals 3, 4, and 5, respectively. The time required for the erosion of the crest width, t₁, is calculated for each experiment. The relation between relative tailwater depth and relative time of crest width erosion is shown in Fig. 15. It is found that the time of crest width erosion increases linearly with increasing, d_o /Z_o. The percent of increase is 36.4, 54.5 and 77.3 % for relative tailwater depth, d_o /(d_o)_ref = 3, 4 and 5, respectively.

Crest height, Z_crest is calculated from the experimental results and the Flow 3D results for relative tailwater depths, d_o/(d_o)_ref, = 3, 4, and 5. A relation between relative crest height, Z_crest/Z_o with time from experimental and numerical results is presented in Fig. 16. From Fig. 16, it is seen that there is a good consistency between the results of numerical model and the experimental results in the case of tracking the erosion of the crest height with time.

5.2. Upstream and downstream water depths

It is noticed that at the beginning of the erosion process, both upstream and downstream water depths increase linearly with time as long as erosion of the crest height did not take place. However, when the crest height starts to lower the upstream water depth decreases with time while the downstream water depth increases. At the end of the experiment, the two depths are nearly equal. A relation between relative downstream and upstream water depths with time is drawn for each experiment as shown in Fig. 17.

5.3. Eroded volume

A MATLAB code is used to calculate the cumulative eroded volume every time interval for each experiment. The total volume of the dam, V_total is 0.256 m³. The cumulative eroded volume, V_eroded is 0.21, 0.16, 0.13, and 0.05 m³ for tailwater depths, d_o = 5, 15, 20, and 25 cm, respectively. Fig. 18 presents the relation between cumulative eroded volume, V_eroded and time. From Fig. 18, it is observed that the cumulative eroded volume decreases with increasing the tailwater depth. The reduction in cumulative eroded volume is 23, 36.5, and 75 % for relative tailwater depth, d_o /(d_o)_ref = 3, 4, and 5, respectively. The relative remained volume of the dam equals 0.18, 0.375, 0.492, and 0.8 for tailwater depths = 5, 15, 20, and 25 cm, respectively. Fig. 19 shows a relation between relative tailwater depth and relative cumulative eroded volume from experimental results. From that figure, it is noticed that the eroded volume decreases exponentially with increasing relative tailwater depth.

5.4. The outflow discharge

The inflow discharge provided to the storage tank is maintained constant for all experiments. The water surface elevation, H, over the sharp-crested weir placed at the downstream side is recorded by the video camera 2. For each experiment, the outflow discharge is then calculated by using the sharp-crested rectangular weir equation every 10 sec.

The outflow discharge is found to increase rapidly until it reaches its peak then it decreases until it is constant. For high values of tailwater depths, the peak discharge becomes less than that in the case of small tailwater depth as shown in Fig. 20 which agrees well with the results of Rifai et al. [14] The reduction in peak discharge is 7, 14, and 17.35 % for relative tailwater depth, d_o /(d_o)_ref = 3, 4, and 5, respectively.

The scenario presented in this article in which the tailwater depth rises due to unexpected heavy rainfall, is investigated to find the effect of rising tailwater depth on earth dam failure. The results revealed that rising tailwater depth positively affects the process of dam failure in terms of preventing the dam from complete failure and reducing the outflow discharge.

6. Conclusions

The effect of tailwater depth on earth dam failure due to overtopping is investigated experimentally in this work. The study focuses on the effect of tailwater depth on side erosion, upstream and downstream water depths, eroded volume, outflow hydrograph, and duration of the failure process. The Flow 3D numerical software is used to simulate the dam failure, and a comparison is made between the experimental and numerical results to find the ability of this software to simulate the erosion process. The following are the results of the investigation:

The existence of tailwater with high depths prevents the dam from completely collapsing thereby turning it into a broad crested weir. The failure time decreases with increasing the tailwater depth and the reduction from the reference case is found to be 35.3, 45, and 57 % for relative tailwater depth, d_o /(d_o)_ref = 3, 4, and 5, respectively. The difference between the upstream and downstream water depths decreases with time till it became almost negligible at the end of the experiment. The reduction in cumulative eroded volume is 23, 36.5, and 75 % for relative tailwater depth, d_o /(d_o)_ref = 3, 4, and 5, respectively. The peak discharge decreases by 7, 14, and 17.35 % for relative tailwater depth, d_o /(d_o)_ref = 3, 4, and 5, respectively. The relative eroded crest height decreases linearly with increasing the tailwater depth by 10, 41, and 77.6 % for relative tailwater depth, d_o /(d_o)_ref = 3, 4, and 5, respectively. The numerical model can reproduce the erosion process with a minor deviation from the experimental results, particularly in terms of tracking the degradation of the crest height with time.

Declaration of Competing Interest

The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper.

Reference

[1]

D. McCullough

The Johnstown Flood

Simon and Schuster, NY (1968)

Google Scholar [2]Rose AT. The influence of dam failures on dam safety laws in Pennsylvania. Association of State Dam Safety Officials Annual Conference 2013, Dam Safety 2013. 2013;1:738–56.

Google Scholar [3]

M. Foster, R. Fell, M. Spannagle

The statistics of embankment dam failures and accidents

Can Geotech J, 37 (5) (2000), pp. 1000-1024, 10.1139/t00-030 View PDF

View Record in Scopus Google Scholar [4]Pickert, G., Jirka, G., Bieberstein, A., Brauns, J. Soil/water interaction during the breaching process of overtopped embankments. In: Greco, M., Carravetta, A., Morte, R.D. (Eds.), Proceedings of the Conference River-Flow 2004, Balkema.

Google Scholar [5]

A. Asghari Tabrizi, E. Elalfy, M. Elkholy, M.H. Chaudhry, J. Imran

Effects of compaction on embankment breach due to overtopping

J Hydraul Res, 55 (2) (2017), pp. 236-247, 10.1080/00221686.2016.1238014 View PDF

View Record in Scopus Google Scholar [6]

R.M. Kansoh, M. Elkholy, G. Abo-Zaid

Effect of Shape Parameters on Failure of Earthen Embankment due to Overtopping

KSCE J Civ Eng, 24 (5) (2020), pp. 1476-1485, 10.1007/s12205-020-1107-x View PDF

View Record in Scopus Google Scholar [7]

YongHui Zhu, P.J. Visser, J.K. Vrijling, GuangQian Wang

Experimental investigation on breaching of embankments

Experimental investigation on breaching of embankments, 54 (1) (2011), pp. 148-155 View PDF

CrossRef View Record in Scopus Google Scholar [8]Amaral S, Jónatas R, Bento AM, Palma J, Viseu T, Cardoso R, et al. Failure by overtopping of earth dams. Quantification of the discharge hydrograph. Proceedings of the 3rd IAHR Europe Congress: 14-15 April 2014, Portugal. 2014;(1):182–93.

Google Scholar [9]

G. Bereta, P. Hui, H. Kai, L. Guang, P. Kefan, Y.Z. Zhao

Experimental study of cohesive embankment dam breach formation due to overtopping

Periodica Polytechnica Civil Engineering, 64 (1) (2020), pp. 198-211, 10.3311/PPci.14565 View PDF

View Record in Scopus Google Scholar [10]

D.K. Verma, B. Setia, V.K. Arora

Experimental study of breaching of an earthen dam using a fuse plug model

Int J Eng Trans A, 30 (4) (2017), pp. 479-485, 10.5829/idosi.ije.2017.30.04a.04 View PDF

View Record in Scopus Google Scholar [11]Wu T, Qin J. Experimental Study of a Tailings Impoundment Dam Failure Due to Overtopping. Mine Water and the Environment [Internet]. 2018;37(2):272–80. Available from: doi: 10.1007/s10230-018-0529-x.

Google Scholar [12]

A. Feizi Khankandi, A. Tahershamsi, S. Soares-Frazo

Experimental investigation of reservoir geometry effect on dam-break flow

J Hydraul Res, 50 (4) (2012), pp. 376-387 View PDF

CrossRef View Record in Scopus Google Scholar [13]

A. Ritter

Die Fortpflanzung der Wasserwellen (The propagation of water waves)

Zeitschrift Verein Deutscher Ingenieure, 36 (33) (1892), pp. 947-954

[in German]

View Record in Scopus Google Scholar [14]

I. Rifai, K. El Kadi Abderrezzak, S. Erpicum, P. Archambeau, D. Violeau, M. Pirotton, et al.

Floodplain Backwater Effect on Overtopping Induced Fluvial Dike Failure

Water Resour Res, 54 (11) (2018), pp. 9060-9073 View PDF

This article is free to access.

CrossRef View Record in Scopus Google Scholar [15]

X. Jiang

Laboratory Experiments on Breaching Characteristics of Natural Dams on Sloping Beds

Advances in Civil Engineering, 2019 (2019), pp. 1-14

View Record in Scopus Google Scholar [16]

H. Ozmen-Cagatay, S. Kocaman

Dam-break flows during initial stage using SWE and RANS approaches

J Hydraul Res, 48 (5) (2010), pp. 603-611 View PDF

CrossRef View Record in Scopus Google Scholar [17]

S. Evangelista

Experiments and numerical simulations of dike erosion due to a wave impact

Water (Switzerland), 7 (10) (2015), pp. 5831-5848 View PDF

CrossRef View Record in Scopus Google Scholar [18]

C. Di Cristo, S. Evangelista, M. Greco, M. Iervolino, A. Leopardi, A. Vacca

Dam-break waves over an erodible embankment: experiments and simulations

J Hydraul Res, 56 (2) (2018), pp. 196-210 View PDF

CrossRef View Record in Scopus Google Scholar [19]Goharnejad H, Sm M, Zn M, Sadeghi L, Abadi K. Numerical Modeling and Evaluation of Embankment Dam Break Phenomenon (Case Study : Taleghan Dam) ISSN : 2319-9873. 2016;5(3):104–11.

Google Scholar [20]Hu H, Zhang J, Li T. Dam-Break Flows : Comparison between Flow-3D , MIKE 3 FM , and Analytical Solutions with Experimental Data. 2018;1–24. doi: 10.3390/app8122456.

Google Scholar [21]

R. Kaurav, P.K. Mohapatra, D. Ph

Studying the Peak Discharge through a Planar Dam Breach, 145 (6) (2019), pp. 1-8 View PDF

CrossRef [22]

Z.M. Yusof, Z.A.L. Shirling, A.K.A. Wahab, Z. Ismail, S. Amerudin

A hydrodynamic model of an embankment breaching due to overtopping flow using FLOW-3D

IOP Conference Series: Earth and Environmental Science, 920 (1) (2021)

Google Scholar [23]

G. Pickert, V. Weitbrecht, A. Bieberstein

Breaching of overtopped river embankments controlled by apparent cohesion

J Hydraul Res, 49 (2) (Apr. 2011), pp. 143-156, 10.1080/00221686.2011.552468 View PDF

View Record in Scopus Google Scholar

Cited by (0)

My name is Shaimaa Ibrahim Mohamed Aman and I am a teaching assistant in Irrigation and Hydraulics department, Faculty of Engineering, Alexandria University. I graduated from the Faculty of Engineering, Alexandria University in 2013. I had my MSc in Irrigation and Hydraulic Engineering in 2017. My research interests lie in the area of earth dam Failures.

Peer review under responsibility of Ain Shams University.

PDF 원문보기

Nanoparticle-enabled increase of energy efficiency during laser metal additive manufacturing

레이저 금속 적층 제조 중 나노 입자로 에너지 효율 증가

Minglei Quo ^bQilin Guo ^a bLuis ^IzetEscano ^a bAli Nabaa ^a bKamel Fezzaa ^cLianyi Chen ^a b

레이저 금속 적층 제조(AM) 공정의 낮은 에너지 효율은 대규모 산업 생산에서 잠재적인 지속 가능성 문제입니다. 레이저 용융을 위한 에너지 효율의 명시적 조사는 용융 금속의 불투명한 특성으로 인해 매우 어려운 용융 풀 치수 및 증기 내림의 직접적인 특성화를 요구합니다.

여기에서 우리는 현장 고속 고에너지 x-선 이미징에 의해 Al6061의 레이저 분말 베드 융합(LPBF) 동안 증기 강하 및 용융 풀 형성에 대한 TiC 나노 입자의 효과에 대한 직접적인 관찰 및 정량화를 보고합니다. 정량 결과를 바탕으로, 우리는 Al6061의 LPBF 동안 TiC 나노 입자가 있거나 없을 때 레이저 용융 에너지 효율(여기서 재료를 용융하는 데 필요한 에너지 대 레이저 빔에 의해 전달되는 에너지의 비율로 정의)을 계산했습니다.

결과는 TiC 나노 입자를 Al6061에 추가하면 레이저 용융 에너지 효율이 크게 증가한다는 것을 보여줍니다(평균 114% 증가, 312에서 521% 증가). W 레이저 출력, 0.4m /s 스캔 속도). 체계적인 특성 측정, 시뮬레이션 및 x-선 이미징 연구를 통해 우리는 처음으로 세 가지 메커니즘이 함께 작동하여 레이저 용융 에너지 효율을 향상시킨다는 것을 확인할 수 있었습니다.

(1) TiC 나노 입자를 추가하면 흡수율이 증가합니다. (2) TiC 나노입자를 추가하면 열전도율이 감소하고, (3) TiC 나노입자를 추가하면 더 낮은 레이저 출력에서 증기 억제 및 다중 반사를 시작할 수 있습니다(즉, 키홀링에 대한 레이저 출력 임계값을 낮춤).

여기서 보고한 Al6061의 LPBF 동안 레이저 용융 에너지 효율을 증가시키기 위해 TiC 나노입자를 사용하는 방법 및 메커니즘은 보다 에너지 효율적인 레이저 금속 AM을 위한 공급원료 재료의 개발을 안내할 수 있습니다.

The low energy efficiency of the laser metal additive manufacturing (AM) process is a potential sustainability concern for large-scale industrial production. Explicit investigation of the energy efficiency for laser melting requires the direct characterization of melt pool dimension and vapor depression, which is very difficult due to the opaque nature of the molten metal. Here we report the direct observation and quantification of effects of the TiC nanoparticles on the vapor depression and melt pool formation during laser powder bed fusion (LPBF) of Al6061 by in-situ high-speed high-energy x-ray imaging. Based on the quantification results, we calculated the laser melting energy efficiency (defined here as the ratio of the energy needed to melt the material to the energy delivered by the laser beam) with and without TiC nanoparticles during LPBF of Al6061. The results show that adding TiC nanoparticles into Al6061 leads to a significant increase of laser melting energy efficiency (114% increase on average, 521% increase under 312 W laser power, 0.4 m/s scan speed). Systematic property measurement, simulation, and x-ray imaging studies enable us, for the first time, to identify that three mechanisms work together to enhance the laser melting energy efficiency: (1) adding TiC nanoparticles increases the absorptivity; (2) adding TiC nanoparticles decreases the thermal conductivity, and (3) adding TiC nanoparticles enables the initiation of vapor depression and multiple reflection at lower laser power (i.e., lowers the laser power threshold for keyholing). The method and mechanisms of using TiC nanoparticles to increase the laser melting energy efficiency during LPBF of Al6061 we reported here may guide the development of feedstock materials for more energy efficient laser metal AM.

Keywords

Additive manufacturing

laser powder bed fusion

energy efficiency

keyhole

melt pool

x-ray imaging

metal matrix nanocomposites

원문보기

The failure propagation of weakly stable sediment: A reason for the formation of high-velocity turbidity currents in submarine canyons

약한 안정 퇴적물의 실패 전파: 해저 협곡에서 고속 탁도 흐름이 형성되는 이유

Yupeng Ren, Yi Zhang, Guohui Xu, Xingbei Xu, Houjie Wang & Zhiyuan Chen

Abstract

Abstract해저 협곡에서 탁도의 장거리 이동은 많은 양의 퇴적물을 심해 평원으로 운반할 수 있습니다. 이전 연구에서는 5.9~28.0m/s 범위의 다중 케이블 손상 이벤트에서 파생된 탁도 전류 속도와 0.15~7.2m/s 사이의 현장 관찰 결과에서 명백한 차이가 있음을 보여줍니다. 따라서 해저 환경의 탁한 유체가 해저 협곡을 고속으로 장거리로 흐를 수 있는지에 대한 질문이 남아 있습니다. 연구실 시험의 결합을 통해 해저협곡의 탁류의 고속 및 장거리 운동을 설명하기 위해 약안정 퇴적물 기반의 새로운 모델(약안정 퇴적물에 대한 파손 전파 모델 제안, 줄여서 WSS-PFP 모델)을 제안합니다. 및 수치 아날로그. 이 모델은 두 가지 메커니즘을 기반으로 합니다. 1) 원래 탁도류는 약하게 안정한 퇴적층의 불안정화를 촉발하고 연질 퇴적물의 불안정화 및 하류 방향으로의 이동을 촉진하고 2) 원래 탁도류가 협곡으로 이동할 때 형성되는 여기파가 불안정화로 이어진다. 하류 방향으로 약하게 안정한 퇴적물의 수송. 제안된 모델은 심해 퇴적, 오염 물질 이동 및 광 케이블 손상 연구를 위한 동적 프로세스 해석을 제공할 것입니다.

The long-distance movement of turbidity currents in submarine canyons can transport large amounts of sediment to deep-sea plains. Previous studies show obvious differences in the turbidity current velocities derived from the multiple cables damage events ranging from 5.9 to 28.0 m/s and those of field observations between 0.15 and 7.2 m/s. Therefore, questions remain regarding whether a turbid fluid in an undersea environment can flow through a submarine canyon for a long distance at a high speed. A new model based on weakly stable sediment is proposed (proposed failure propagation model for weakly stable sediments, WSS-PFP model for short) to explain the high-speed and long-range motion of turbidity currents in submarine canyons through the combination of laboratory tests and numerical analogs. The model is based on two mechanisms: 1) the original turbidity current triggers the destabilization of the weakly stable sediment bed and promotes the destabilization and transport of the soft sediment in the downstream direction and 2) the excitation wave that forms when the original turbidity current moves into the canyon leads to the destabilization and transport of the weakly stable sediment in the downstream direction. The proposed model will provide dynamic process interpretation for the study of deep-sea deposition, pollutant transport, and optical cable damage.

Keyword

turbidity current
excitation wave
dense basal layer
velocity
WSS-PFP model

References

Azpiroz-Zabala M, Cartigny M J B, Talling P J et al. 2017. Newly recognized turbidity current structure can explain prolonged flushing of submarine canyons. Science Advances, 3(10): e1700200, https://doi.org/10.1126/sciadv.1700200.Article Google Scholar
Bagnold R A. 1962. Auto-suspension of transported sediment; turbidity currents. Proceedings of the Royal Society A: Mathematical, Physical and Engineering Sciences, 265(1322): 315–319, https://doi.org/10.1098/rspa.1962.0012.Google Scholar
Carter L, Gavey R, Talling P J et al. 2014. Insights into submarine geohazards from breaks in subsea telecommunication cables. Oceanography, 27(2): 58–67, https://doi.org/10.5670/oceanog.2014.40.Article Google Scholar
Carter L, Milliman J D, Talling P J et al. 2012. Near-synchronous and delayed initiation of long run-out submarine sediment flows from a record-breaking river flood, offshore Taiwan. Geophysical Research Letters, 39(12): L12603, https://doi.org/10.1029/2012gl051172.Article Google Scholar
Cooper C, Wood J, Imran J et al. 2016. Designing for turbidity currents in the Congo Canyon. In: Offshore Technology Conference. OTC, Houston, TX. OTC-26919-MSp, https://doi.org/10.4043/26919-ms.Google Scholar
Dengler A T, Wilde P, Noda E K et al. 1984. Turbidity currents generated by Hurricane Iwa. Geo-Marine Letters, 4(1): 5–11, https://doi.org/10.1007/bf02237967.Article Google Scholar
Fang A M, Li J L, Hou Q L. 1998. Sedimentation of turbidity currents and relative gravity flows: a review. Geological Review, 44(3): 270–280, https://doi.org/10.16509/j.georeview.1998.03.009. (in Chinese with English abstract)Google Scholar
Felix M, Peakall J. 2006. Transformation of debris flows into turbidity currents: mechanisms inferred from laboratory experiments. Sedimentology, 53(1): 107–123, https://doi.org/10.1111/j.1365-3091.2005.00757.x.Article Google Scholar
Gavey R, Carter L, Liu J T et al. 2017. Frequent sediment density flows during 2006 to 2015, triggered by competing seismic and weather events: observations from subsea cable breaks off southern Taiwan. Marine Geology, 384: 147–158, https://doi.org/10.1016/j.margeo.2016.06.001.Article Google Scholar
Heerema C J, Talling P J, Cartigny M J et al. 2020. What determines the downstream evolution of turbidity currents?. Earth and Planetary Science Letters, 532: 116023, https://doi.org/10.1016/j.epsl.2019.116023.Article Google Scholar
Heezen B C, Ericson D B, Ewing M. 1954. Further evidence for a turbidity current following the 1929 Grand Banks earthquake. Deep Sea Research (1953), 1(4): 193–202, https://doi.org/10.1016/0146-6313(54)90001-5.Article Google Scholar
Heezen B C, Ewing M. 1955. Orleansville earthquake and turbidity currents. AAPG Bulletin, 39(12): 2505–2514, https://doi.org/10.1306/5ceae2e6-16bb-11d7-8645000102c1865d.Google Scholar
Heezen B C, Ewing W M. 1952. Turbidity currents and submarine slumps, and the 1929 Grand Banks earthquake. American Journal of Science, 250(12): 849–873, https://doi.org/10.2475/ajs.250.12.849.Article Google Scholar
Hsu S K, Kuo J, Lo C L et al. 2008. Turbidity currents, submarine landslides and the 2006 Pingtung earthquake off SW Taiwan. Terrestrial, Atmospheric and Oceanic Sciences, 19(6): 767–772, https://doi.org/10.3319/tao.2008.19.6.767(pt).Article Google Scholar
Krause D C, White W C, Piper D J W et al. 1970. Turbidity currents and cable breaks in the western New Britain Trench. GSA Bulletin, 81(7): 2153–2160, https://doi.org/10.1130/0016-7606(1970)81[2153:tcacbi]2.0.co;2.Article Google Scholar
Kuenen P H. 1952. Estimated size of the Grand Banks turbidity current. American Journal of Science, 250(12): 874–884, https://doi.org/10.2475/ajs.250.12.874.Article Google Scholar
Lambert A M, Kelts K R, Marshall N F. 1976. Measurements of density underflows from Walensee, Switzerland. Sedimentology, 23(1): 87–105, https://doi.org/10.1111/j.1365-3091.1976.tb00040.x.Article Google Scholar
Liu J T, Wang Y H, Yang R J et al. 2012. Cyclone-induced hyperpycnal turbidity currents in a submarine canyon. Journal of Geophysical Research, 117(C4): C04033, https://doi.org/10.1029/2011jc007630.Article Google Scholar
Maier K L, Gales J A, Paull C K et al. 2019. Linking direct measurements of turbidity currents to submarine canyon-floor deposits. Frontiers in Earth Science, 7: 144, https://doi.org/10.3389/feart.2019.00144.Article Google Scholar
Mulder T, Syvitski J P M, Migeon S et al. 2003. Marine hyperpycnal flows: initiation, behavior and related deposits. A review. Marine and Petroleum Geology, 20(6–8): 861–882, https://doi.org/10.1016/j.marpetgeo.2003.01.003.Article Google Scholar
Nie X, Luo W D, Zhou J. 2017. Depositional characteristics of the Penghu submarine canyon in the northeastern South China Sea. Marine Geology Frontiers, 33(8): 18–23, https://doi.org/10.16028/j.1009-2722.2017.08003. (in Chinese with English abstract)Google Scholar
Nilsen T H, Shew R D, Steffens G S et al. 2008. Atlas of Deep-Water Outcrops. AAPG, Tulsa, https://doi.org/10.1306/St561240.Book Google Scholar
Parker G, Fukushima Y, Pantin H M. 1986. Self-accelerating turbidity currents. Journal of Fluid Mechanics, 171: 145–181, https://doi.org/10.1017/s0022112086001404.Article Google Scholar
Parker G. 1982. Conditions for the ignition of catastrophically erosive turbidity currents. Marine Geology, 46(3–4): 307–327, https://doi.org/10.1016/0025-3227(82)90086-x.Article Google Scholar
Paull C K, Caress D W, Lundsten E et al. 2013. Anatomy of the La Jolla Submarine Canyon system; offshore southern California. Marine Geology, 335: 16–34, https://doi.org/10.1016/j.margeo.2012.10.003.Article Google Scholar
Paull C K, Caress D W, Ussler III B et al. 2011. High-resolution bathymetry of the axial channels within Monterey and Soquel submarine canyons, offshore central California. Geosphere, 7(5): 1077–1101, https://doi.org/10.1130/GES00636.1.Article Google Scholar
Paull C K, Talling P J, Maier K L et al. 2018. Powerful turbidity currents driven by dense basal layers. Nature Communications, 9(1): 4114, https://doi.org/10.1038/s41467-018-06254-6.Article Google Scholar
Piper D J W, Shor A N, Clarke J E H. 1988. The 1929 “Grand banks” earthquake, slump, and turbidity current. In: Clifton H E ed. Sedimentologic Consequences of Convulsive Geologic Events. Geological Society of America. p.77–92, https://doi.org/10.1130/SPE229-p77.
Sequeiros O E, Mosquera R, Pedocchi F. 2018. Internal structure of a self-accelerating turbidity current. Journal of Geophysical Research, 123(9): 6260–6276, https://doi.org/10.1029/2018jc014061.Article Google Scholar
Sequeiros O E, Naruse H, Endo N et al. 2009. Experimental study on self-accelerating turbidity currents. Journal of Geophysical Research, 114(C5): C05025, https://doi.org/10.1029/2008jc005149.Article Google Scholar
Shepard F P. 1954. High-velocity turbidity currents, a discussion. Proceedings of the Royal Society of Series A: Mathematical, Physical and Engineering Sciences, 222(1150): 323–326, https://doi.org/10.1098/rspa.1954.0072.Google Scholar
Stetson H C, Smith J F. 1938. Behavior of suspension currents and mud slides on the continental slope. American Journal of Science, s5–35(205): 1–13, https://doi.org/10.2475/ajs.s5-35.205.1.Article Google Scholar
Symons W Q, Sumner E J, Paull C K et al. 2017. A new model for turbidity current behavior based on integration of flow monitoring and precision coring in a submarine canyon. Geology, 45(4): 367–370, https://doi.org/10.1130/g38764.1.Article Google Scholar
Talling P J, Allin J, Armitage D A et al. 2015. Key future directions for research on turbidity currents and their deposits. Journal of Sedimentary Research, 85(2): 153–169, https://doi.org/10.2110/jsr.2015.03.Article Google Scholar
Wang Z W, Xu J P, Talling P J et al. 2020. Direct evidence of a high-concentration basal layer in a submarine turbidity current. Deep Sea Research Part I: Oceanographic Research Papers, 161: 103300, https://doi.org/10.1016/j.dsr.2020.103300.Article Google Scholar
Winterwerp J C. 2006. Stratification effects by fine suspended sediment at low, medium, and very high concentrations. Journal of Geophysical Research, 111(C5): C05012, https://doi.org/10.1029/2005jc003019.Article Google Scholar
Xu J P. 2014. Turbidity Current research in the past century: an overview. Periodical of Ocean University of China, 44(10): 98–105, https://doi.org/10.16441/j.cnki.hdxb.2014.10.014.Google Scholar
Zeng J J, Lowe D R, Prior D B et al. 1991. Flow properties of turbidity currents in Bute Inlet, British Columbia. Sedimentology, 38(6): 975–996, https://doi.org/10.1111/j.1365-3091.1991.tb00367.x.Article Google Scholar
Zhang X, Wang L, Krabbenhoft K et al. 2020. A case study and implication: particle finite element modelling of the 2010 Saint-Jude sensitive clay landslide. Landslides, 17(5): 1117–1127, https://doi.org/10.1007/s10346-019-01330-4.Article Google Scholar
Zhang Y W, Liu Z F, Zhao Y L et al. 2018. Long-term in situ observations on typhoon-triggered turbidity currents in the deep sea. Geology, 46(8): 675–678, https://doi.org/10.1130/g45178.1.Article Google Scholar
Zhou H G. 2020. Experimental study on flow ability and fixed sand bed shear force of turbid suspension.

Download references

Acknowledgment

We thank Hanru WU from Ocean University of China for his help in thesis writing, and Hao TIAN and Chenxi WANG from Ocean University of China for their helps in the preparation of the experimental materials. Guohui XU is responsible for the development of the initial concept, processing of test data, and management of coauthor contributions to the paper; Yupeng REN for the experiment setup and drafting of the paper; Yi ZHANG and Xingbei XU for the simulation part of the experiment; Houjie WANG for writing guidance; Zhiyuan CHEN for the experiment setup.

Author information

Authors and Affiliations

Shandong Provincial Key Laboratory of Marine Environment and Geological Engineering, Qingdao, 266100, ChinaYupeng Ren, Yi Zhang, Guohui Xu, Xingbei Xu & Zhiyuan Chen
Shandong Provincial Key Laboratory of Marine Environment and Geological Engineering, Ocean University of China, Qingdao, 266100, ChinaYupeng Ren & Houjie Wang
Key Laboratory of Marine Environment and Ecology, Ocean University of China, Ministry of Education, Qingdao, 266100, ChinaYi Zhang, Guohui Xu, Xingbei Xu & Zhiyuan Chen

Corresponding author

Correspondence to Guohui Xu.

Additional information

Supported by the National Natural Science Foundation of China (Nos. 41976049, 41720104001) and the Taishan Scholar Project of Shandong Province (No. TS20190913), and the Fundamental Research Funds for the Central Universities (No. 202061028)

Data Availability Statement

The datasets generated and/or analyzed during the current study are available from the corresponding author upon reasonable request.

Rights and permissions

Reprints and Permissions

About this article

Cite this article

Ren, Y., Zhang, Y., Xu, G. et al. The failure propagation of weakly stable sediment: A reason for the formation of high-velocity turbidity currents in submarine canyons. J. Ocean. Limnol. (2022). https://doi.org/10.1007/s00343-022-1285-0

원문보기

Fig. 1. (a) Dimensions of the casting with runners (unit: mm), (b) a melt flow simulation using Flow-3D software together with Reilly's model[44], predicted that a large amount of bifilms (denoted by the black particles) would be contained in the final casting. (c) A solidification simulation using Pro-cast software showed that no shrinkage defect was contained in the final casting.

AZ91 합금 주물 내 연행 결함에 대한 캐리어 가스의 영향

TianLi^abJ.M.T.Davies^aXiangzhenZhu^c
^aUniversity of Birmingham, Birmingham B15 2TT, United Kingdom
^bGrainger and Worrall Ltd, Bridgnorth WV15 5HP, United Kingdom
^cBrunel Centre for Advanced Solidification Technology, Brunel University London, Kingston Ln, London, Uxbridge UB8 3PH, United Kingdom

Abstract

An entrainment defect (also known as a double oxide film defect or bifilm) acts a void containing an entrapped gas when submerged into a light-alloy melt, thus reducing the quality and reproducibility of the final castings. Previous publications, carried out with Al-alloy castings, reported that this trapped gas could be subsequently consumed by the reaction with the surrounding melt, thus reducing the void volume and negative effect of entrainment defects. Compared with Al-alloys, the entrapped gas within Mg-alloy might be more efficiently consumed due to the relatively high reactivity of magnesium. However, research into the entrainment defects within Mg alloys has been significantly limited. In the present work, AZ91 alloy castings were produced under different carrier gas atmospheres (i.e., SF₆/CO₂, SF₆/air). The evolution processes of the entrainment defects contained in AZ91 alloy were suggested according to the microstructure inspections and thermodynamic calculations. The defects formed in the different atmospheres have a similar sandwich-like structure, but their oxide films contained different combinations of compounds. The use of carrier gases, which were associated with different entrained-gas consumption rates, affected the reproducibility of AZ91 castings.

연행 결함(이중 산화막 결함 또는 이중막이라고도 함)은 경합금 용융물에 잠길 때 갇힌 가스를 포함하는 공극으로 작용하여 최종 주물의 품질과 재현성을 저하시킵니다. Al-합금 주물을 사용하여 수행된 이전 간행물에서는 이 갇힌 가스가 주변 용융물과의 반응에 의해 후속적으로 소모되어 공극 부피와 연행 결함의 부정적인 영향을 줄일 수 있다고 보고했습니다. Al-합금에 비해 마그네슘의 상대적으로 높은 반응성으로 인해 Mg-합금 내에 포집된 가스가 더 효율적으로 소모될 수 있습니다. 그러나 Mg 합금 내 연행 결함에 대한 연구는 상당히 제한적이었습니다. 현재 작업에서 AZ91 합금 주물은 다양한 캐리어 가스 분위기(즉, SF6/CO2, SF6/공기)에서 생산되었습니다. AZ91 합금에 포함된 연행 결함의 진화 과정은 미세 조직 검사 및 열역학 계산에 따라 제안되었습니다. 서로 다른 분위기에서 형성된 결함은 유사한 샌드위치 구조를 갖지만 산화막에는 서로 다른 화합물 조합이 포함되어 있습니다. 다른 동반 가스 소비율과 관련된 운반 가스의 사용은 AZ91 주물의 재현성에 영향을 미쳤습니다.

Keywords

Magnesium alloy, Casting, Oxide film, Bifilm, Entrainment defect, Reproducibility

1. Introduction

As the lightest structural metal available on Earth, magnesium became one of the most attractive light metals over the last few decades. The magnesium industry has consequently experienced a rapid development in the last 20 years [1,2], indicating a large growth in demand for Mg alloys all over the world. Nowadays, the use of Mg alloys can be found in the fields of automobiles, aerospace, electronics and etc.[3,4]. It has been predicted that the global consumption of Mg metals will further increase in the future, especially in the automotive industry, as the energy efficiency requirement of both traditional and electric vehicles further push manufactures lightweight their design [3,5,6].

The sustained growth in demand for Mg alloys motivated a wide interest in the improvement of the quality and mechanical properties of Mg-alloy castings. During a Mg-alloy casting process, surface turbulence of the melt can lead to the entrapment of a doubled-over surface film containing a small quantity of the surrounding atmosphere, thus forming an entrainment defect (also known as a double oxide film defect or bifilm) [7], [8], [9], [10]. The random size, quantity, orientation, and placement of entrainment defects are widely accepted to be significant factors linked to the variation of casting properties [7]. In addition, Peng et al. [11] found that entrained oxides films in AZ91 alloy melt acted as filters to Al₈Mn₅ particles, trapping them as they settle. Mackie et al. [12] further suggested that entrained oxide films can act to trawl the intermetallic particles, causing them to cluster and form extremely large defects. The clustering of intermetallic compounds made the entrainment defects more detrimental for the casting properties.

Most of the previous studies regarding entrainment defects were carried out on Al-alloys [7,[13], [14], [15], [16], [17], [18], and a few potential methods have been suggested for diminishing their negative effect on the quality of Al-alloy castings. Nyahumwa et al.,[16] shows that the void volume within entrainment defects could be reduced by a hot isostatic pressing (HIP) process. Campbell [7] suggested the entrained gas within the defects could be consumed due to reaction with the surrounding melt, which was further verified by Raiszedeh and Griffiths [19].The effect of the entrained gas consumption on the mechanical properties of Al-alloy castings has been investigated by [8,9], suggesting that the consumption of the entrained gas promoted the improvement of the casting reproducibility.

Compared with the investigation concerning the defects within Al-alloys, research into the entrainment defects within Mg-alloys has been significantly limited. The existence of entrainment defects has been demonstrated in Mg-alloy castings [20,21], but their behaviour, evolution, as well as entrained gas consumption are still not clear.

In a Mg-alloy casting process, the melt is usually protected by a cover gas to avoid magnesium ignition. The cavities of sand or investment moulds are accordingly required to be flushed with the cover gas prior to the melt pouring [22]. Therefore, the entrained gas within Mg-alloy castings should contain the cover gas used in the casting process, rather than air only, which may complicate the structure and evolution of the corresponding entrainment defects.

SF₆ is a typical cover gas widely used for Mg-alloy casting processes [23], [24], [25]. Although this cover gas has been restricted to use in European Mg-alloy foundries, a commercial report has pointed out that this cover is still popular in global Mg-alloy industry, especially in the countries which dominated the global Mg-alloy production, such as China, Brazil, India, etc. [26]. In addition, a survey in academic publications also showed that this cover gas was widely used in recent Mg-alloy studies [27]. The protective mechanism of SF₆ cover gas (i.e., the reaction between liquid Mg-alloy and SF₆ cover gas) has been investigated by several previous researchers, but the formation process of the surface oxide film is still not clearly understood, and even some published results are conflicting with each other. In early 1970s, Fruehling [28] found that the surface film formed under SF₆ was MgO mainly with traces of fluorides, and suggested that SF₆ was absorbed in the Mg-alloy surface film. Couling [29] further noticed that the absorbed SF₆ reacted with the Mg-alloy melt to form MgF₂. In last 20 years, different structures of the Mg-alloy surface films have been reported, as detailed below.(1)

Single-layered film. Cashion [30,31] used X-ray Photoelectron Spectroscopy (XPS) and Auger Spectroscopy (AES) to identify the surface film as MgO and MgF₂. He also found that composition of the film was constant throughout the thickness and the whole experimental holding time. The film observed by Cashion had a single-layered structure created from a holding time from 10 min to 100 min.(2)

Double-layered film. Aarstad et. al [32] reported a doubled-layered surface oxide film in 2003. They observed several well-distributed MgF₂ particles attached to the preliminary MgO film and grew until they covered 25–50% of the total surface area. The inward diffusion of F through the outer MgO film was the driving force for the evolution process. This double-layered structure was also supported by Xiong’s group [25,33] and Shih et al. [34].(3)

Triple-layered film. The triple-layered film and its evolution process were reported in 2002 by Pettersen [35]. Pettersen found that the initial surface film was a MgO phase and then gradually evolved to the stable MgF₂ phase by the inward diffusion of F. In the final stage, the film has a triple-layered structure with a thin O-rich interlayer between the thick top and bottom MgF₂ layers.(4)

Oxide film consisted of discrete particles. Wang et al [36] stirred the Mg-alloy surface film into the melt under a SF₆ cover gas, and then inspect the entrained surface film after the solidification. They found that the entrained surface films were not continues as the protective surface films reported by other researchers but composed of discrete particles. The young oxide film was composed of MgO nano-sized oxide particles, while the old oxide films consist of coarse particles (about 1 µm in average size) on one side that contained fluorides and nitrides.

The oxide films of a Mg-alloy melt surface or an entrained gas are both formed due to the reaction between liquid Mg-alloy and the cover gas, thus the above-mentioned research regarding the Mg-alloy surface film gives valuable insights into the evolution of entrainment defects. The protective mechanism of SF₆ cover gas (i.e., formation of a Mg-alloy surface film) therefore indicated a potential complicated evolution process of the corresponding entrainment defects.

However, it should be noted that the formation of a surface film on a Mg-alloy melt is in a different situation to the consumption of an entrained gas that is submerged into the melt. For example, a sufficient amount of cover gas was supported during the surface film formation in the studies previously mentioned, which suppressed the depletion of the cover gas. In contrast, the amount of entrained gas within a Mg-alloy melt is finite, and the entrained gas may become fully depleted. Mirak [37] introduced 3.5%SF₆/air bubbles into a pure Mg-alloy melt solidifying in a specially designed permanent mould. It was found that the gas bubbles were entirely consumed, and the corresponding oxide film was a mixture of MgO and MgF₂. However, the nucleation sites (such as the MgF₂ spots observed by Aarstad [32] and Xiong [25,33]) were not observed. Mirak also speculated that the MgF₂ formed prior to MgO in the oxide film based on the composition analysis, which was opposite to the surface film formation process reported in previous literatures (i.e., MgO formed prior to MgF₂). Mirak’s work indicated that the oxide-film formation of an entrained gas may be quite different from that of surface films, but he did not reveal the structure and evolution of the oxide films.

In addition, the use of carrier gas in the cover gases also influenced the reaction between the cover gas and the liquid Mg-alloy. SF₆/air required a higher content of SF₆ than did a SF₆/CO₂ carrier gas [38], to avoid the ignition of molten magnesium, revealing different gas-consumption rates. Liang et.al [39] suggested that carbon was formed in the surface film when CO₂ was used as a carrier gas, which was different from the films formed in SF₆/air. An investigation into Mg combustion [40] reported a detection of Mg₂C₃ in the Mg-alloy sample after burning in CO₂, which not only supported Liang’s results, but also indicated a potential formation of Mg carbides in double oxide film defects.

The work reported here is an investigation into the behaviour and evolution of entrainment defects formed in AZ91 Mg-alloy castings, protected by different cover gases (i.e., SF₆/air and SF₆/CO₂). These carrier gases have different protectability for liquid Mg alloy, which may be therefore associated with different consumption rates and evolution processes of the corresponding entrained gases. The effect of the entrained-gas consumption on the reproducibility of AZ91 castings was also studied.

2. Experiment

2.1. Melting and casting

Three kilograms AZ91 alloy was melted in a mild steel crucible at 700 ± 5 °C. The composition of the AZ91 alloy has been shown in Table 1. Prior to heating, all oxide scale on the ingot surface was removed by machining. The cover gases used were 0.5%SF₆/air or 0.5%SF₆/CO₂ (vol.%) at a flow rate of 6 L/min for different castings. The melt was degassed by argon with a flow rate of 0.3 L/min for 15 min [41,42], and then poured into sand moulds. Prior to pouring, the sand mould cavity was flushed with the cover gas for 20 min [22]. The residual melt (around 1 kg) was solidified in the crucible.

Table 1. Composition (wt.%) of the AZ91 alloy used in this study.

Al	Zn	Mn	Si	Fe	Ni	Mg
9.4	0.61	0.15	0.02	0.005	0.0017	Residual

Fig. 1(a) shows the dimensions of the casting with runners. A top-filling system was deliberately used to generate entrainment defects in the final castings. Green and Campbell [7,43] suggested that a top-filling system caused more entrainment events (i.e., bifilms) during a casting process, compared with a bottom-filling system. A melt flow simulation (Flow-3D software) of this mould, using Reilly’s model [44] regarding the entrainment events, also predicted that a large amount of bifilms would be contained in the final casting (denoted by the black particles in Fig. 1b).

Shrinkage defects also affect the mechanical properties and reproducibility of castings. Since this study focused on the effect of bifilms on the casting quality, the mould has been deliberately designed to avoid generating shrinkage defects. A solidification simulation using ProCAST software showed that no shrinkage defect would be contained in the final casting, as shown in Fig. 1c. The casting soundness has also been confirmed using a real time X-ray prior to the test bar machining.

The sand moulds were made from resin-bonded silica sand, containing 1wt. % PEPSET 5230 resin and 1wt. % PEPSET 5112 catalyst. The sand also contained 2 wt.% Na₂SiF₆ to act as an inhibitor [45]. The pouring temperature was 700 ± 5 °C. After the solidification, a section of the runner bars was sent to the Sci-Lab Analytical Ltd for a H-content analysis (LECO analysis), and all the H-content measurements were carried out on the 5th day after the casting process. Each of the castings was machined into 40 test bars for a tensile strength test, using a Zwick 1484 tensile test machine with a clip extensometer. The fracture surfaces of the broken test bars were examined using Scanning Electron Microscope (SEM, Philips JEOL7000) with an accelerating voltage of 5–15 kV. The fractured test bars, residual Mg-alloy solidified in the crucible, and the casting runners were then sectioned, polished and also inspected using the same SEM. The cross-section of the oxide film found on the test-bar fracture surface was exposed by the Focused Ion Beam milling technique (FIB), using a CFEI Quanta 3D FEG FIB-SEM. The oxide film required to be analysed was coated with a platinum layer. Then, a gallium ion beam, accelerated to 30 kV, milled the material substrate surrounding the platinum coated area to expose the cross section of the oxide film. EDS analysis of the oxide film’s cross section was carried out using the FIB equipment at accelerating voltage of 30 kV.

2.2. Oxidation cell

As previously mentioned, several past researchers investigated the protective film formed on a Mg-alloy melt surface [38,39,[46], [47], [48], [49], [50], [51], [52]. During these experiments, the amount of cover gas used was sufficient, thus suppressing the depletion of fluorides in the cover gas. The experiment described in this section used a sealed oxidation cell, which limited the supply of cover gas, to study the evolution of the oxide films of entrainment defects. The cover gas contained in the oxidation cell was regarded as large-size “entrained bubble”.

As shown in Fig. 2, the main body of the oxidation cell was a closed-end mild steel tube which had an inner length of 400 mm, and an inner diameter of 32 mm. A water-cooled copper tube was wrapped around the upper section of the cell. When the tube was heated, the cooling system created a temperature difference between the upper and lower sections, causing the interior gas to convect within the tube. The temperature was monitored by a type-K thermocouple located at the top of the crucible. Nie et al. [53] suggested that the SF₆ cover gas would react with the steel wall of the holding furnace when they investigated the surface film of a Mg-alloy melt. To avoid this reaction, the interior surface of the steel oxidation cell (shown in Fig. 2) and the upper half section of the thermocouple were coated with boron nitride (the Mg-alloy was not in contact with boron nitride).

Fig. 2. Schematic of the oxidation cell used to study the evolution of the oxide films of the entrainment defects (unit mm).

During the experiment, a block of solid AZ91 alloy was placed in a magnesia crucible located at the bottom of the oxidation cell. The cell was heated to 100 °C in an electric resistance furnace under a gas flow rate of 1 L/min. The cell was held at this temperature for 20 min, to replace the original trapped atmosphere (i.e. air). Then, the oxidation cell was further heated to 700 °C, melting the AZ91 sample. The gas inlet and exit valves were then closed, creating a sealed environment for oxidation under a limited supply of cover gas. The oxidation cell was then held at 700 ± 10 °C for periods of time from 5 min to 30 min in 5-min intervals. At the end of each holding time, the cell was quenched in water. After cooling to room temperature, the oxidised sample was sectioned, polished, and subsequently examined by SEM.

3. Results

3.1. Structure and composition of the entrainment defects formed in SF₆/air

The structure and composition of the entrainment defect formed in the AZ91 castings under a cover gas of 0.5%SF₆/air was observed by SEM and EDS. The results indicate that there exist two types of entrainment defects which are sketched in Fig. 3: (1) Type A defect whose oxide film has a traditional single-layered structure and (2) Type B defect, whose oxide film has two layers. The details of these defects were introduced in the following. Here it should be noticed that, as the entrainment defects are also known as biofilms or double oxide film, the oxide films of Type B defect were referred to as “multi-layered oxide film” or “multi-layered structure” in the present work to avoid a confusing description such as “the double-layered oxide film of a double oxide film defect”.

Fig. 3. Schematic of the different types of entrainment defects found in AZ91 castings. (a) Type A defect with a single-layered oxide film and (b) Type B defect with two-layered oxide film.

Fig. 4(a-b) shows a Type A defect having a compact single-layered oxide film with about 0.4 µm thickness. Oxygen, fluorine, magnesium and aluminium were detected in this film (Fig. 4c). It is speculated that oxide film is the mixture of fluoride and oxide of magnesium and aluminium. The detection of fluorine revealed that an entrained cover gas was contained in the formation of this defect. That is to say that the pores shown in Fig. 4(a) were not shrinkage defects or hydrogen porosity, but entrainment defects. The detection of aluminium was different with Xiong and Wang’s previous study [47,48], which showed that no aluminium was contained in their surface film of an AZ91 melt protected by a SF₆ cover gas. Sulphur could not be clearly recognized in the element map, but there was a S-peak in the corresponding ESD spectrum.

Fig. 4. (a) A Type A entrainment defect formed in SF6/air and having a single-layered oxide film, (b) the oxide film of this defect, (c) SEM-EDS element maps (using Philips JEOL7000) corresponding to the area highlighted in (b).

Fig. 5(a-b) shows a Type B entrainment defect having a multi-layered oxide film. The compact outer layers of the oxide films were enriched with fluorine and oxygen (Fig. 5c), while their relatively porous inner layers were only enriched with oxygen (i.e., poor in fluorine) and partly grew together, thus forming a sandwich-like structure. Therefore, it is speculated that the outer layer is the mixture of fluoride and oxide, while the inner layer is mainly oxide. Sulphur could only be recognized in the EDX spectrum and could not be clearly identified in the element map, which might be due to the small S-content in the cover gas (i.e., 0.5% volume content of SF₆ in the cover gas). In this oxide film, aluminium was contained in the outer layer of this oxide film but could not be clearly detected in the inner layer. Moreover, the distribution of Al seems to be uneven. It can be found that, in the right side of the defect, aluminium exists in the film but its concentration can not be identified to be higher than the matrix. However, there is a small area with much higher aluminium concentration in the left side of the defect. Such an uneven distribution of aluminium was also observed in other defects (shown in the following), and it is the result of the formation of some oxide particles in or under the film.

Fig. 5. (a) A Type B entrainment defect formed in SF6/air and having a multi-layered oxide film, (b) the oxide films of this defect have grown together, (c) SEM-EDS element maps (using Philips JEOL7000) corresponding to the area shown in (b).

Figs. 4 and 5 show cross sectional observations of the entrainment defects formed in the AZ91 alloy sample cast under a cover gas of SF₆/air. It is not sufficient to characterize the entrainment defects only by the figures observed from the two-dimensional section. To have a further understanding, the surface of the entrainment defects (i.e. the oxide film) was further studied by observing the fracture surface of the test bars.

Fig. 6(a) shows fracture surfaces of an AZ91 alloy tensile test bar produced in SF₆/air. Symmetrical dark regions can be seen on both sides of the fracture surfaces. Fig. 6(b) shows boundaries between the dark and bright regions. The bright region consisted of jagged and broken features, while the surface of the dark region was relatively smooth and flat. In addition, the EDS results (Fig. 6c-d and Table 2) show that fluorine, oxygen, sulphur, and nitrogen were only detected in the dark regions, indicating that the dark regions were surface protective films entrained into the melt. Therefore, it could be suggested that the dark regions were an entrainment defect with consideration of their symmetrical nature. Similar defects on fracture surfaces of Al-alloy castings have been previously reported [7]. Nitrides were only found in the oxide films on the test-bar fracture surfaces but never detected in the cross-sectional samples shown in Figs. 4 and 5. An underlying reason is that the nitrides contained in these samples may have hydrolysed during the sample polishing process [54].

Fig. 6. (a) A pair of the fracture surfaces of a AZ91 alloy tensile test bar produced under a cover gas of SF6/air. The dimension of the fracture surface is 5 mm × 6 mm, (b) a section of the boundary between the dark and bright regions shown in (a), (c-d) EDS spectrum of the (c) bright regions and (d) dark regions, (e) schematic of an entrainment defect contained in a test bar.

Table 2. EDS results (wt.%) corresponding to the regions shown in Fig. 6 (cover gas: SF₆/air).

Empty Cell	C	O	Mg	F	Al	Zn	S	N
Dark region in Fig. 6(b)	3.48	1.32	79.13	0.47	13.63	0.57	0.08	0.73
Bright region in Fig. 6(b)	3.58	–	84.48	–	11.25	0.68	–	–

In conjunction with the cross-sectional observation of the defects shown in Figs. 4 and 5, the structure of an entrainment defect contained in a tensile test bar was sketched as shown in Fig. 6(e). The defect contained an entrained gas enclosed by its oxide film, creating a void section inside the test bar. When the tensile force applied on the defect during the fracture process, the crack was initiated at the void section and propagated along the entrainment defect, since cracks would be propagated along the weakest path [55]. Therefore, when the test bar was finally fractured, the oxide films of entrainment defect appeared on both fracture surfaces of the test bar, as shown in Fig. 6(a).

3.2. Structure and composition of the entrainment defects formed in SF₆/CO₂

Similar to the entrainment defect formed in SF₆/air, the defects formed under a cover gas of 0.5%SF₆/CO₂ also had two types of oxide films (i.e., single-layered and multi-layered types). Fig. 7(a) shows an example of the entrainment defects containing a multi-layered oxide film. A magnified observation to the defect (Fig. 7b) shows that the inner layers of the oxide films had grown together, presenting a sandwich-like structure, which was similar to the defects formed in an atmosphere of SF₆/air (Fig. 5b). An EDS spectrum (Fig. 7c) revealed that the joint area (inner layer) of this sandwich-like structure mainly contained magnesium oxides. Peaks of fluorine, sulphur, and aluminium were recognized in this EDS spectrum, but their amount was relatively small. In contrast, the outer layers of the oxide films were compact and composed of a mixture of fluorides and oxides (Fig. 7d-e).

Fig. 7. (a) An example of entrainment defects formed in SF6/CO2 and having a multi-layered oxide film, (b) magnified observation of the defect, showing the inner layer of the oxide films has grown together, (c) EDS spectrum of the point denoted in (b), (d) outer layer of the oxide film, (e) SEM-EDS element maps (using Philips JEOL7000) corresponding to the area shown in (d).

Fig. 8(a) shows an entrainment defect on the fracture surfaces of an AZ91 alloy tensile test bar, which was produced in an atmosphere of 0.5%SF₆/CO₂. The corresponding EDS results (Table 3) showed that oxide film contained fluorides and oxides. Sulphur and nitrogen were not detected. Besides, a magnified observation (Fig. 8b) indicated spots on the oxide film surface. The diameter of the spots ranged from hundreds of nanometres to a few micron meters.

Fig. 8. (a) A pair of the fracture surfaces of a AZ91 alloy tensile test bar, produced in an atmosphere of SF6/CO2. The dimension of the fracture surface is 5 mm × 6 mm, (b) surface appearance of the oxide films on the fracture surfaces, showing spots on the film surface.

To further reveal the structure and composition of the oxide film clearly, the cross-section of the oxide film on a test-bar fracture surface was onsite exposed using the FIB technique (Fig. 9). As shown in Fig. 9a, a continuous oxide film was found between the platinum coating layer and the Mg-Al alloy substrate. Fig. 9 (b-c) shows a magnified observation to oxide films, indicating a multi-layered structure (denoted by the red box in Fig. 9c). The bottom layer was enriched with fluorine and oxygen and should be the mixture of fluoride and oxide, which was similar to the “outer layer” shown in Figs. 5 and 7, while the only-oxygen-enriched top layer was similar to the “inner layer” shown in Figs. 5 and 7.

Fig. 9. (a) A cross-sectional observation of the oxide film on the fracture surface of the AZ91 casting produced in SF6/CO2, exposed by FIB, (b) a magnified observation of area highlighted in (a), and (c) SEM-EDS elements map of the area shown in (b), obtained by CFEI Quanta 3D FEG FIB-SEM.

Except the continuous film, some individual particles were also observed in or below the continuous film, as shown in Fig. 9. An Al-enriched particle was detected in the left side of the oxide film shown in Fig. 9b and might be speculated to be spinel Mg₂AlO₄ because it also contains abundant magnesium and oxygen elements. The existing of such Mg₂AlO₄ particles is responsible for the high concentration of aluminium in small areas of the observed film and the uneven distribution of aluminium, as shown in Fig. 5(c). Here it should be emphasized that, although the other part of the bottom layer of the continuous oxide film contains less aluminium than this Al-enriched particle, the Fig. 9c indicated that the amount of aluminium in this bottom layer was still non-negligible, especially when comparing with the outer layer of the film. Below the right side of the oxide film shown in Fig. 9b, a particle was detected and speculated to be MgO because it is rich in Mg and O. According to Wang’s result [56], lots of discrete MgO particles can be formed on the surface of the Mg melt by the oxidation of Mg melt and Mg vapor. The MgO particles observed in our present work may be formed due to the same reasons. While, due to the differences in experimental conditions, less Mg melt can be vapored or react with O₂, thus only a few of MgO particles formed in our work. An enrichment of carbon was also found in the film, revealing that CO₂ was able to react with the melt, thus forming carbon or carbides. This carbon concentration was consistent with the relatively high carbon content of the oxide film shown in Table 3 (i.e., the dark region). In the area next to the oxide film.

Table 3. EDS results (wt.%) corresponding to the regions shown in Fig. 8 (cover gas: SF₆/ CO₂).

Empty Cell	C	O	Mg	F	Al	Zn	S	N
Dark region in Fig. 8(a)	7.25	3.64	69.82	3.82	7.03	0.86	–	–
Bright region in Fig. 8(a)	2.10	0.44	82.83	–	13.26	1.36	–	–

This cross-sectional observation of the oxide film on a test bar fracture surface (Fig. 9) further verified the schematic of the entrainment defect shown in Fig. 6(e). The entrainment defects formed in different atmospheres of SF₆/CO₂ and SF₆/air had similar structures, but their compositions were different.

3.3. Evolution of the oxide films in the oxidation cell

The results in Section 3.1 and 3.2 have shown the structures and compositions of entrainment defects formed in AZ91 castings under cover gases of SF₆/air and SF₆/CO₂. Different stages of the oxidation reaction may lead to the different structures and compositions of entrainment defects. Although Campbell has conjectured that an entrained gas may react with the surrounding melt, it is rarely reported that the reaction occurring between the Mg-alloy melt and entrapped cover gas. Previous researchers normally focus on the reaction between a Mg-alloy melt and the cover gas in an open environment [38,39,[46], [47], [48], [49], [50], [51], [52], which was different from the situation of a cover gas trapped into the melt. To further understand the formation of the entrainment defect in an AZ91 alloy, the evolution process of oxide films of the entrainment defect was further studied using an oxidation cell.

Fig. 10 (a and d) shows a surface film held for 5 min in the oxidation cell, protected by 0.5%SF₆/air. There was only one single layer consisting of fluoride and oxide (MgF₂ and MgO). In this surface film. Sulphur was detected in the EDS spectrum, but its amount was too small to be recognized in the element map. The structure and composition of this oxide film was similar to the single-layered films of entrainment defects shown in Fig. 4.

Fig. 10. Oxide films formed in the oxidation cell under a cover gas of 0.5%SF6/air and held at 700 °C for (a) 5 min; (b) 10 min; (c) 30 min, and (d-f) the SEM-EDS element maps (using Philips JEOL7000) corresponding to the oxide film shown in (a-c) respectively, (d) 5 min; (e) 10 min; (f) 30 min. The red points in (c and f) are the location references, denoting the boundary of the F-enriched layer in different element maps.

After a holding time of 10 min, a thin (O, S)-enriched top layer (around 700 nm) appeared upon the preliminary F-enriched film, forming a multi-layered structure, as shown in Fig. 10(b and e). The thickness of the (O, S)-enriched top layer increased with increased holding time. As shown in Fig. 10(c and f), the oxide film held for 30 min also had a multi-layered structure, but the thickness of its (O, S)-enriched top layer (around 2.5 µm) was higher than the that of the 10-min oxide film. The multi-layered oxide films shown in Fig. 10(b-c) presented a similar appearance to the films of the sandwich-like defect shown in Fig. 5.

The different structures of the oxide films shown in Fig. 10 indicated that fluorides in the cover gas would be preferentially consumed due to the reaction with the AZ91 alloy melt. After the depletion of fluorides, the residual cover gas reacted further with the liquid AZ91 alloy, forming the top (O, S)-enriched layer in the oxide film. Therefore, the different structures and compositions of entrainment defects shown in Figs. 4 and 5 may be due to an ongoing oxidation reaction between melt and entrapped cover gas.

This multi-layered structure has not been reported in previous publications concerning the protective surface film formed on a Mg-alloy melt [38,[46], [47], [48], [49], [50], [51]. This may be due to the fact that previous researchers carried out their experiments with an un-limited amount of cover gas, creating a situation where the fluorides in the cover gas were not able to become depleted. Therefore, the oxide film of an entrainment defect had behaviour traits similar to the oxide films shown in Fig. 10, but different from the oxide films formed on the Mg-alloy melt surface reported in [38,[46], [47], [48], [49], [50], [51].

Similar with the oxide films held in SF₆/air, the oxide films formed in SF₆/CO₂ also had different structures with different holding times in the oxidation cell. Fig. 11(a) shows an oxide film, held on an AZ91 melt surface under a cover gas of 0.5%SF₆/CO₂ for 5 min. This film had a single-layered structure consisting of MgF₂. The existence of MgO could not be confirmed in this film. After the holding time of 30 min, the film had a multi-layered structure; the inner layer was of a compact and uniform appearance and composed of MgF₂, while the outer layer is the mixture of MgF₂ and MgO. Sulphur was not detected in this film, which was different from the surface film formed in 0.5%SF₆/air. Therefore, fluorides in the cover gas of 0.5%SF₆/CO₂ were also preferentially consumed at an early stage of the film growth process. Compared with the film formed in SF₆/air, the MgO in film formed in SF₆/CO₂ appeared later and sulphide did not appear within 30 min. It may mean that the formation and evolution of film in SF₆/air is faster than SF₆/CO_2. CO₂ may have subsequently reacted with the melt to form MgO, while sulphur-containing compounds accumulated in the cover gas and reacted to form sulphide in very late stage (may after 30 min in oxidation cell).

Fig. 11. Oxide films formed in the oxidation cell under a cover gas of 0.5%SF6/CO2, and their SEM-EDS element maps (using Philips JEOL7000). They were held at 700 °C for (a) 5 min; (b) 30 min. The red points in (b) are the location references, denoting the boundary between the top and bottom layers in the oxide film.

4. Discussion

4.1. Evolution of entrainment defects formed in SF₆/air

HSC software from Outokumpu HSC Chemistry for Windows (http://www.hsc-chemistry.net/) was used to carry out thermodynamic calculations needed to explore the reactions which might occur between the trapped gases and liquid AZ91 alloy. The solutions to the calculations suggest which products are most likely to form in the reaction process between a small amount of cover gas (i.e., the amount within a trapped bubble) and the AZ91-alloy melt.

In the trials, the pressure was set to 1 atm, and the temperature set to 700 °C. The amount of the cover gas was assumed to be 7 × 10⁻⁷ kg, with a volume of approximately 0.57 cm³ (3.14 × 10⁻⁸ kmol) for 0.5%SF₆/air, and 0.35 cm³ (3.12 × 10⁻⁸ kmol) for 0.5%SF₆/CO₂. The amount of the AZ91 alloy melt in contact with the trapped gas was assumed to be sufficient to complete all reactions. The decomposition products of SF₆ were SF₅, SF₄, SF₃, SF₂, F₂, S(g), S₂(g) and F(g) [57], [58], [59], [60].

Fig. 12 shows the equilibrium diagram of the thermodynamic calculation of the reaction between the AZ91 alloy and 0.5%SF₆/air. In the diagram, the reactants and products with less than 10⁻¹⁵ kmol have not been shown, as this was 5 orders of magnitude less than the amount of SF₆ present (≈ 1.57 × 10⁻¹⁰ kmol) and therefore would not affect the observed process in a practical way.

Fig. 12. An equilibrium diagram for the reaction between 7e-7 kg 0.5%SF6/air and a sufficient amount of AZ91 alloy. The X axis is the amount of AZ91 alloy melt having reacted with the entrained gas, and the vertical Y-axis is the amount of the reactants and products.

This reaction process could be divided into 3 stages.

Stage 1: The formation of fluorides. the AZ91 melt preferentially reacted with SF₆ and its decomposition products, producing MgF₂, AlF₃, and ZnF₂. However, the amount of ZnF₂ may have been too small to be detected practically (1.25 × 10⁻¹² kmol of ZnF₂ compared with 3 × 10⁻¹⁰ kmol of MgF₂), which may be the reason why Zn was not detected in any the oxide films shown in Sections 3.1–3.3. Meanwhile, sulphur accumulated in the residual gas as SO₂.

Stage 2: The formation of oxides. After the liquid AZ91 alloy had depleted all the available fluorides in the entrapped gas, the amount of AlF₃ and ZnF₂ quickly reduced due to a reaction with Mg. O₂(g) and SO₂ reacted with the AZ91 melt, forming MgO, Al₂O₃, MgAl₂O₄, ZnO, ZnSO₄ and MgSO₄. However, the amount of ZnO and ZnSO₄ would have been too small to be found practically by EDS (e.g. 9.5 × 10⁻¹² kmol of ZnO,1.38 × 10⁻¹⁴ kmol of ZnSO₄, in contrast to 4.68 × 10⁻¹⁰ kmol of MgF₂, when the amount of AZ91 on the X-axis is 2.5 × 10⁻⁹ kmol). In the experimental cases, the concentration of F in the cover gas is very low, whole the concentration f O is much higher. Therefore, the stage 1 and 2, i.e, the formation of fluoride and oxide may happen simultaneously at the beginning of the reaction, resulting in the formation of a singer-layered mixture of fluoride and oxide, as shown in Figs. 4 and 10(a). While an inner layer consisted of oxides but fluorides could form after the complete depletion of F element in the cover gas.

Stages 1- 2 theoretically verified the formation process of the multi-layered structure shown in Fig. 10.

The amount of MgAl₂O₄ and Al₂O₃ in the oxide film was of a sufficient amount to be detected, which was consistent with the oxide films shown in Fig. 4. However, the existence of aluminium could not be recognized in the oxide films grown in the oxidation cell, as shown in Fig. 10. This absence of Al may be due to the following reactions between the surface film and AZ91 alloy melt:(1)

Al₂O₃ + 3Mg + = 3MgO + 2Al, △G(700 °C) = -119.82 kJ/mol(2)

Mg + MgAl₂O₄ = MgO + Al, △G(700 °C) =-106.34 kJ/molwhich could not be simulated by the HSC software since the thermodynamic calculation was carried out under an assumption that the reactants were in full contact with each other. However, in a practical process, the AZ91 melt and the cover gas would not be able to be in contact with each other completely, due to the existence of the protective surface film.

Stage 3: The formation of Sulphide and nitride. After a holding time of 30 min, the gas-phase fluorides and oxides in the oxidation cell had become depleted, allowing the melt reaction with the residual gas, forming an additional sulphur-enriched layer upon the initial F-enriched or (F, O)-enriched surface film, thus resulting in the observed multi-layered structure shown in Fig. 10 (b and c). Besides, nitrogen reacted with the AZ91 melt until all reactions were completed. The oxide film shown in Fig. 6 may correspond to this reaction stage due to its nitride content. However, the results shows that the nitrides were not detected in the polished samples shown in Figs. 4 and 5, but only found on the test bar fracture surfaces. The nitrides may have hydrolysed during the sample preparation process, as follows [54]:(3)

Mg₃N₂ + 6H₂O =3Mg(OH)₂ + 2NH₃↑(4)

AlN+ 3H₂O =Al(OH)₃ + NH₃↑

In addition, Schmidt et al. [61] found that Mg₃N₂ and AlN could react to form ternary nitrides (Mg₃Al_nN_n+2, n= 1, 2, 3…). HSC software did not contain the database of ternary nitrides, and it could not be added into the calculation. The oxide films in this stage may also contain ternary nitrides.

4.2. Evolution of entrainment defects formed in SF₆/CO₂

Fig. 13 shows the results of the thermodynamic calculation between AZ91 alloy and 0.5%SF₆/CO₂. This reaction processes can also be divided into three stages.

Fig. 13. An equilibrium diagram for the reaction between 7e-7 kg 0.5%SF6/CO2 and a sufficient amount of AZ91 alloy. The X axis denotes the amount of Mg alloy melt having reacted with the entrained gas, and the vertical Y-axis denotes the amounts of the reactants and products.

Stage 1: The formation of fluorides. SF₆ and its decomposition products were consumed by the AZ91 melt, forming MgF₂, AlF₃, and ZnF₂. As in the reaction of AZ91 in 0.5%SF₆/air, the amount of ZnF₂ was too small to be detected practically (1.51 × 10⁻¹³ kmol of ZnF₂ compared with 2.67 × 10⁻¹⁰ kmol of MgF₂). Sulphur accumulated in the residual trapped gas as S₂(g) and a portion of the S₂(g) reacted with CO₂, to form SO₂ and CO. The products in this reaction stage were consistent with the film shown in Fig. 11(a), which had a single layer structure that contained fluorides only.

Stage 2: The formation of oxides. AlF₃ and ZnF₂ reacted with the Mg in the AZ91 melt, forming MgF₂, Al and Zn. The SO₂ began to be consumed, producing oxides in the surface film and S₂(g) in the cover gas. Meanwhile, the CO₂ directly reacted with the AZ91 melt, forming CO, MgO, ZnO, and Al₂O₃. The oxide films shown in Figs. 9 and 11(b) may correspond to this reaction stage due to their oxygen-enriched layer and multi-layered structure.

The CO in the cover gas could further react with the AZ91 melt, producing C. This carbon may further react with Mg to form Mg carbides, when the temperature reduced (during solidification period) [62]. This may be the reason for the high carbon content in the oxide film shown in Figs. 8–9. Liang et al. [39] also reported carbon-detection in an AZ91 alloy surface film protected by SO₂/CO₂. The produced Al₂O₃ may be further combined with MgO, forming MgAl₂O₄ [63]. As discussed in Section 4.1, the alumina and spinel can react with Mg, causing an absence of aluminium in the surface films, as shown in Fig. 11.

Stage 3: The formation of Sulphide. the AZ91 melt began to consume S₂(g) in the residual entrapped gas, forming ZnS and MgS. These reactions did not occur until the last stage of the reaction process, which could be the reason why the S-content in the defect shown Fig. 7(c) was small.

In summary, thermodynamic calculations indicate that the AZ91 melt will react with the cover gas to form fluorides firstly, then oxides and sulphides in the last. The oxide film in the different reaction stages would have different structures and compositions.

4.3. Effect of the carrier gases on consumption of the entrained gas and the reproducibility of AZ91 castings

The evolution processes of entrainment defects, formed in SF₆/air and SF₆/CO₂, have been suggested in Sections 4.1 and 4.2. The theoretical calculations were verified with respect to the corresponding oxide films found in practical samples. The atmosphere within an entrainment defect could be efficiently consumed due to the reaction with liquid Mg-alloy, in a scenario dissimilar to the Al-alloy system (i.e., nitrogen in an entrained air bubble would not efficiently react with Al-alloy melt [64,65], however, nitrogen would be more readily consumed in liquid Mg alloys, commonly referred to as “nitrogen burning” [66]).

The reaction between the entrained gas and the surrounding liquid Mg-alloy converted the entrained gas into solid compounds (e.g. MgO) within the oxide film, thus reducing the void volume of the entrainment defect and hence probably causing a collapse of the defect (e.g., if an entrained gas of air was depleted by the surrounding liquid Mg-alloy, under an assumption that the melt temperature is 700 °C and the depth of liquid Mg-alloy is 10 cm, the total volume of the final solid products would be 0.044% of the initial volume taken by the entrapped air).

The relationship between the void volume reduction of entrainment defects and the corresponding casting properties has been widely studied in Al-alloy castings. Nyahumwa and Campbell [16] reported that the Hot Isostatic Pressing (HIP) process caused the entrainment defects in Al-alloy castings to collapse and their oxide surfaces forced into contact. The fatigue lives of their castings were improved after HIP. Nyahumwa and Campbell [16] also suggested a potential bonding of the double oxide films that were in contact with each other, but there was no direct evidence to support this. This binding phenomenon was further investigated by Aryafar et.al.[8], who re-melted two Al-alloy bars with oxide skins in a steel tube and then carried out a tensile strength test on the solidified sample. They found that the oxide skins of the Al-alloy bars strongly bonded with each other and became even stronger with an extension of the melt holding time, indicating a potential “healing” phenomenon due to the consumption of the entrained gas within the double oxide film structure. In addition, Raidszadeh and Griffiths [9,19] successfully reduced the negative effect of entrainment defects on the reproducibility of Al-alloy castings, by extending the melt holding time before solidification, which allowed the entrained gas to have a longer time to react with the surrounding melt.

With consideration of the previous work mentioned, the consumption of the entrained gas in Mg-alloy castings may diminish the negative effect of entrainment defects in the following two ways.

(1) Bonding phenomenon of the double oxide films. The sandwich-like structure shown in Fig. 5 and 7 indicated a potential bonding of the double oxide film structure. However, more evidence is required to quantify the increase in strength due to the bonding of the oxide films.

(2) Void volume reduction of entrainment defects. The positive effect of void-volume reduction on the quality of castings has been widely demonstrated by the HIP process [67]. As the evolution processes discussed in Section 4.1–4.2, the oxide films of entrainment defects can grow together due to an ongoing reaction between the entrained gas and surrounding AZ91 alloy melt. The volume of the final solid products was significant small compared with the entrained gas (i.e., 0.044% as previously mentioned).

Therefore, the consumption rate of the entrained gas (i.e., the growth rate of oxide films) may be a critical parameter for improving the quality of AZ91 alloy castings. The oxide film growth rate in the oxidization cell was accordingly further investigated.

Fig. 14 shows a comparison of the surface film growth rates in different cover gases (i.e., 0.5%SF₆/air and 0.5%SF₆/CO₂). 15 random points on each sample were selected for film thickness measurements. The 95% confidence interval (95%CI) was computed under an assumption that the variation of the film thickness followed a Gaussian distribution. It can be seen that all the surface films formed in 0.5%SF₆/air grew faster than those formed in 0.5%SF₆/CO₂. The different growth rates suggested that the entrained-gas consumption rate of 0.5%SF₆/air was higher than that of 0.5%SF₆/CO₂, which was more beneficial for the consumption of the entrained gas.

Fig. 14. A comparison of the AZ91 alloy oxide film growth rates in 0.5%SF6/air and 0.5%SF6/CO2

It should be noted that, in the oxidation cell, the contact area of liquid AZ91 alloy and cover gas (i.e. the size of the crucible) was relatively small with consideration of the large volume of melt and gas. Consequently, the holding time for the oxide film growth within the oxidation cell was comparatively long (i.e., 5–30 min). However, the entrainment defects contained in a real casting are comparatively very small (i.e., a few microns size as shown in Figs. 3–6, and [7]), and the entrained gas is fully enclosed by the surrounding melt, creating a relatively large contact area. Hence the reaction time for cover gas and the AZ91 alloy melt may be comparatively short. In addition, the solidification time of real Mg-alloy sand castings can be a few minutes (e.g. Guo [68] reported that a Mg-alloy sand casting with 60 mm diameter required 4 min to be solidified). Therefore, it can be expected that an entrained gas trapped during an Mg-alloy melt pouring process will be readily consumed by the surrounding melt, especially for sand castings and large-size castings, where solidification times are long.

Therefore, the different cover gases (0.5%SF₆/air and 0.5%SF₆/CO₂) associated with different consumption rates of the entrained gases may affect the reproducibility of the final castings. To verify this assumption, the AZ91 castings produced in 0.5%SF₆/air and 0.5%SF₆/CO₂ were machined into test bars for mechanical evaluation. A Weibull analysis was carried out using both linear least square (LLS) method and non-linear least square (non-LLS) method [69].

Fig. 15(a-b) shows a traditional 2-p linearized Weibull plot of the UTS and elongation of the AZ91 alloy castings, obtained by the LLS method. The estimator used is P= (i-0.5)/N, which was suggested to cause the lowest bias among all the popular estimators [69,70]. The casting produced in SF₆/air has an UTS Weibull moduli of 16.9, and an elongation Weibull moduli of 5.0. In contrast, the UTS and elongation Weibull modulus of the casting produced in SF₆/CO₂ are 7.7 and 2.7 respectively, suggesting that the reproducibility of the casting protected by SF₆/CO₂ were much lower than that produced in SF₆/air.

Fig. 15. The Weibull modulus of AZ91 castings produced in different atmospheres, estimated by (a-b) the linear least square method, (c-d) the non-linear least square method, where SSR is the sum of residual squares.

In addition, the author’s previous publication [69] demonstrated a shortcoming of the linearized Weibull plots, which may cause a higher bias and incorrect R² interruption of the Weibull estimation. A Non-LLS Weibull estimation was therefore carried out, as shown in Fig. 15 (c-d). The UTS Weibull modulus of the SF₆/air casting was 20.8, while the casting produced under SF₆/CO₂ had a lower UTS Weibull modulus of 11.4, showing a clear difference in their reproducibility. In addition, the SF₆/air elongation (El%) dataset also had a Weibull modulus (shape = 5.8) higher than the elongation dataset of SF₆/CO₂ (shape = 3.1). Therefore, both the LLS and Non-LLS estimations suggested that the SF₆/air casting has a higher reproducibility than the SF₆/CO₂ casting. It supports the method that the use of air instead of CO₂ contributes to a quicker consumption of the entrained gas, which may reduce the void volume within the defects. Therefore, the use of 0.5%SF₆/air instead of 0.5%SF₆/CO₂ (which increased the consumption rate of the entrained gas) improved the reproducibility of the AZ91 castings.

However, it should be noted that not all the Mg-alloy foundries followed the casting process used in present work. The Mg-alloy melt in present work was degassed, thus reducing the effect of hydrogen on the consumption of the entrained gas (i.e., hydrogen could diffuse into the entrained gas, potentially suppressing the depletion of the entrained gas [7,71,72]). In contrast, in Mg-alloy foundries, the Mg-alloy melt is not normally degassed, since it was widely believed that there is not a ‘gas problem’ when casting magnesium and hence no significant change in tensile properties [73]. Although studies have shown the negative effect of hydrogen on the mechanical properties of Mg-alloy castings [41,42,73], a degassing process is still not very popular in Mg-alloy foundries.

Moreover, in present work, the sand mould cavity was flushed with the SF₆ cover gas prior to pouring [22]. However, not all the Mg-alloy foundries flushed the mould cavity in this way. For example, the Stone Foundry Ltd (UK) used sulphur powder instead of the cover-gas flushing. The entrained gas within their castings may be SO₂/air, rather than the protective gas.

Therefore, although the results in present work have shown that using air instead of CO₂ improved the reproducibility of the final casting, it still requires further investigations to confirm the effect of carrier gases with respect to different industrial Mg-alloy casting processes.

7. Conclusion

Entrainment defects formed in an AZ91 alloy were observed. Their oxide films had two types of structure: single-layered and multi-layered. The multi-layered oxide film can grow together forming a sandwich-like structure in the final casting.2.

Both the experimental results and the theoretical thermodynamic calculations demonstrated that fluorides in the trapped gas were depleted prior to the consumption of sulphur. A three-stage evolution process of the double oxide film defects has been suggested. The oxide films contained different combinations of compounds, depending on the evolution stage. The defects formed in SF₆/air had a similar structure to those formed in SF₆/CO₂, but the compositions of their oxide films were different. The oxide-film formation and evolution process of the entrainment defects were different from that of the Mg-alloy surface films previous reported (i.e., MgO formed prior to MgF₂).3.

The growth rate of the oxide film was demonstrated to be greater under SF₆/air than SF₆/CO₂, contributing to a quicker consumption of the damaging entrapped gas. The reproducibility of an AZ91 alloy casting improved when using SF₆/air instead of SF₆/CO₂.

Acknowledgements

The authors acknowledge funding from the EPSRC LiME grant EP/H026177/1, and the help from Dr W.D. Griffiths and Mr. Adrian Carden (University of Birmingham). The casting work was carried out in University of Birmingham.

Reference

[1]

M.K. McNutt, SALAZAR K.

Magnesium, Compounds & Metal, U.S. Geological Survey and U.S. Department of the Interior

Reston, Virginia (2013)

Google Scholar [2]

Magnesium

Compounds & Metal, U.S. Geological Survey and U.S. Department of the Interior

(1996)

Google Scholar [3]

I. Ostrovsky, Y. Henn

ASTEC’07 International Conference-New Challenges in Aeronautics, Moscow (2007), pp. 1-5

Aug 19-22

View Record in Scopus Google Scholar [4]

Y. Wan, B. Tang, Y. Gao, L. Tang, G. Sha, B. Zhang, N. Liang, C. Liu, S. Jiang, Z. Chen, X. Guo, Y. Zhao

Acta Mater., 200 (2020), pp. 274-286

Article Download PDF View Record in Scopus [5]

J.T.J. Burd, E.A. Moore, H. Ezzat, R. Kirchain, R. Roth

Appl. Energy, 283 (2021), Article 116269

Article Download PDF View Record in Scopus [6]

A.M. Lewis, J.C. Kelly, G.A. Keoleian

Appl. Energy, 126 (2014), pp. 13-20

Article Download PDF View Record in Scopus [7]

J. Campbell

Castings

Butterworth-Heinemann, Oxford (2004)

Google Scholar [8]

M. Aryafar, R. Raiszadeh, A. Shalbafzadeh

J. Mater. Sci., 45 (2010), pp. 3041-3051 View PDF

CrossRef View Record in Scopus [9]

R. Raiszadeh, W.D. Griffiths

Metall. Mater. Trans. B-Process Metall. Mater. Process. Sci., 42 (2011), pp. 133-143 View PDF

CrossRef View Record in Scopus [10]

R. Raiszadeh, W.D. Griffiths

J. Alloy. Compd., 491 (2010), pp. 575-580

Article Download PDF View Record in Scopus [11]

L. Peng, G. Zeng, T.C. Su, H. Yasuda, K. Nogita, C.M. Gourlay

JOM, 71 (2019), pp. 2235-2244 View PDF

CrossRef View Record in Scopus [12]

S. Ganguly, A.K. Mondal, S. Sarkar, A. Basu, S. Kumar, C. Blawert

Corros. Sci., 166 (2020)[13]

G.E. Bozchaloei, N. Varahram, P. Davami, S.K. Kim

Mater. Sci. Eng. A-Struct. Mater. Prop. Microstruct. Process., 548 (2012), pp. 99-105

View Record in Scopus [14]

S. Fox, J. Campbell

Scr. Mater., 43 (2000), pp. 881-886

Article Download PDF View Record in Scopus [15]

M. Cox, R.A. Harding, J. Campbell

Mater. Sci. Technol., 19 (2003), pp. 613-625

View Record in Scopus [16]

C. Nyahumwa, N.R. Green, J. Campbell

Metall. Mater. Trans. A-Phys. Metall. Mater. Sci., 32 (2001), pp. 349-358

View Record in Scopus [17]

A. Ardekhani, R. Raiszadeh

J. Mater. Eng. Perform., 21 (2012), pp. 1352-1362 View PDF

CrossRef View Record in Scopus [18]

X. Dai, X. Yang, J. Campbell, J. Wood

Mater. Sci. Technol., 20 (2004), pp. 505-513

View Record in Scopus [19]

E.M. Elgallad, M.F. Ibrahim, H.W. Doty, F.H. Samuel

Philos. Mag., 98 (2018), pp. 1337-1359 View PDF

CrossRef View Record in Scopus [20]

W.D. Griffiths, N.W. Lai

Metall. Mater. Trans. A-Phys. Metall. Mater. Sci., 38A (2007), pp. 190-196 View PDF

CrossRef View Record in Scopus [21]

A.R. Mirak, M. Divandari, S.M.A. Boutorabi, J. Campbell

Int. J. Cast Met. Res., 20 (2007), pp. 215-220 View PDF

CrossRef View Record in Scopus [22]

C. Cingi

Laboratory of Foundry Engineering

Helsinki University of Technology, Espoo, Finland (2006)

Google Scholar [23]

Y. Jia, J. Hou, H. Wang, Q. Le, Q. Lan, X. Chen, L. Bao

J. Mater. Process. Technol., 278 (2020), Article 116542

Article Download PDF View Record in Scopus [24]

S. Ouyang, G. Yang, H. Qin, S. Luo, L. Xiao, W. Jie

Mater. Sci. Eng. A, 780 (2020), Article 139138

Article Download PDF View Record in Scopus [25]

S.-m. Xiong, X.-F. Wang

Trans. Nonferrous Met. Soc. China, 20 (2010), pp. 1228-1234

Article Download PDF View Record in Scopus [26]

G.V. Research

Grand View Research

(2018)

USA

Google Scholar [27]

T. Li, J. Davies

Metall. Mater. Trans. A, 51 (2020), pp. 5389-5400 View PDF

CrossRef View Record in Scopus [28]J.F. Fruehling, The University of Michigan, 1970.

Google Scholar [29]

S. Couling

36th Annual World Conference on Magnesium, Norway (1979), pp. 54-57

View Record in Scopus Google Scholar [30]

S. Cashion, N. Ricketts, P. Hayes

J. Light Met., 2 (2002), pp. 43-47

Article Download PDF View Record in Scopus [31]

S. Cashion, N. Ricketts, P. Hayes

J. Light Met., 2 (2002), pp. 37-42

Article Download PDF View Record in Scopus [32]

K. Aarstad, G. Tranell, G. Pettersen, T.A. Engh

Various Techniques to Study the Surface of Magnesium Protected by SF6

TMS (2003)

Google Scholar [33]

S.-M. Xiong, X.-L. Liu

Metall. Mater. Trans. A, 38 (2007), pp. 428-434 View PDF

CrossRef View Record in Scopus [34]

T.-S. Shih, J.-B. Liu, P.-S. Wei

Mater. Chem. Phys., 104 (2007), pp. 497-504

Article Download PDF View Record in Scopus [35]

G. Pettersen, E. Øvrelid, G. Tranell, J. Fenstad, H. Gjestland

Mater. Sci. Eng. A, 332 (2002), pp. 285-294

Article Download PDF View Record in Scopus [36]

H. Bo, L.B. Liu, Z.P. Jin

J. Alloy. Compd., 490 (2010), pp. 318-325

Article Download PDF View Record in Scopus [37]

A. Mirak, C. Davidson, J. Taylor

Corros. Sci., 52 (2010), pp. 1992-2000

Article Download PDF View Record in Scopus [38]

B.D. Lee, U.H. Beak, K.W. Lee, G.S. Han, J.W. Han

Mater. Trans., 54 (2013), pp. 66-73 View PDF

View Record in Scopus [39]

W.Z. Liang, Q. Gao, F. Chen, H.H. Liu, Z.H. Zhao

China Foundry, 9 (2012), pp. 226-230 View PDF

CrossRef [40]

U.I. Gol’dshleger, E.Y. Shafirovich

Combust. Explos. Shock Waves, 35 (1999), pp. 637-644[41]

A. Elsayed, S.L. Sin, E. Vandersluis, J. Hill, S. Ahmad, C. Ravindran, S. Amer Foundry

Trans. Am. Foundry Soc., 120 (2012), pp. 423-429[42]

E. Zhang, G.J. Wang, Z.C. Hu

Mater. Sci. Technol., 26 (2010), pp. 1253-1258

View Record in Scopus [43]

N.R. Green, J. Campbell

Mater. Sci. Eng. A-Struct. Mater. Prop. Microstruct. Process., 173 (1993), pp. 261-266

Article Download PDF View Record in Scopus [44]

C Reilly, MR Jolly, NR Green

Proceedings of MCWASP XII – 12th Modelling of Casting, Welding and Advanced Solidifcation Processes, Vancouver, Canada (2009)

Google Scholar [45]H.E. Friedrich, B.L. Mordike, Springer, Germany, 2006.

Google Scholar [46]

C. Zheng, B.R. Qin, X.B. Lou

Proceedings of the 2010 International Conference on Mechanical, Industrial, and Manufacturing Technologies, ASME (2010), pp. 383-388

Mimt 2010 View PDF

CrossRef View Record in Scopus Google Scholar [47]

S.M. Xiong, X.F. Wang

Trans. Nonferrous Met. Soc. China, 20 (2010), pp. 1228-1234

Article Download PDF View Record in Scopus [48]

S.M. Xiong, X.L. Liu

Metall. Mater. Trans. A-Phys. Metall. Mater. Sci., 38A (2007), pp. 428-434 View PDF

CrossRef View Record in Scopus [49]

T.S. Shih, J.B. Liu, P.S. Wei

Mater. Chem. Phys., 104 (2007), pp. 497-504

Article Download PDF View Record in Scopus [50]

K. Aarstad, G. Tranell, G. Pettersen, T.A. Engh

Magn. Technol. (2003), pp. 5-10[51]

G. Pettersen, E. Ovrelid, G. Tranell, J. Fenstad, H. Gjestland

Mater. Sci. Eng. A-Struct. Mater. Prop. Microstruct. Process., 332 (2002), pp. 285-294

Article Download PDF View Record in Scopus [52]

X.F. Wang, S.M. Xiong

Corros. Sci., 66 (2013), pp. 300-307

Article Download PDF View Record in Scopus [53]

S.H. Nie, S.M. Xiong, B.C. Liu

Mater. Sci. Eng. A-Struct. Mater. Prop. Microstruct. Process., 422 (2006), pp. 346-351

Article Download PDF View Record in Scopus [54]

C. Bauer, A. Mogessie, U. Galovsky

Zeitschrift Fur Metallkunde, 97 (2006), pp. 164-168 View PDF

CrossRef[55]

Q.G. Wang, D. Apelian, D.A. Lados

J. Light Met., 1 (2001), pp. 73-84

Article Download PDF View Record in Scopus [56]

S. Wang, Y. Wang, Q. Ramasse, Z. Fan

Metall. Mater. Trans. A, 51 (2020), pp. 2957-2974[57]

S. Hayashi, W. Minami, T. Oguchi, H.J. Kim

Kag. Kog. Ronbunshu, 35 (2009), pp. 411-415 View PDF

CrossRef View Record in Scopus [58]

K. Aarstad

Norwegian University of Science and Technology

(2004)

Google Scholar [59]

R.L. Wilkins

J. Chem. Phys., 51 (1969), p. 853

View Record in Scopus [60]

O. Kubaschewski, K. Hesselemam

Thermo-Chemical Properties of Inorganic Substances

Springer-Verlag, Belin (1991)

Google Scholar [61]

R. Schmidt, M. Strobele, K. Eichele, H.J. Meyer

Eur. J. Inorg. Chem. (2017), pp. 2727-2735 View PDF

CrossRef View Record in Scopus [62]

B. Hu, Y. Du, H. Xu, W. Sun, W.W. Zhang, D. Zhao

J. Min. Metall. Sect. B-Metall., 46 (2010), pp. 97-103

View Record in Scopus [63]

O. Salas, H. Ni, V. Jayaram, K.C. Vlach, C.G. Levi, R. Mehrabian

J. Mater. Res., 6 (1991), pp. 1964-1981

View Record in Scopus [64]

S.S.S. Kumari, U.T.S. Pillai, B.C. Pai

J. Alloy. Compd., 509 (2011), pp. 2503-2509

Article Download PDF View Record in Scopus [65]

H. Scholz, P. Greil

J. Mater. Sci., 26 (1991), pp. 669-677

View Record in Scopus [66]

P. Biedenkopf, A. Karger, M. Laukotter, W. Schneider

Magn. Technol., 2005 (2005), pp. 39-42

View Record in Scopus [67]

H.V. Atkinson, S. Davies

Metall. Mater. Trans. A, 31 (2000), pp. 2981-3000 View PDF

CrossRef View Record in Scopus [68]

E.J. Guo, L. Wang, Y.C. Feng, L.P. Wang, Y.H. Chen

J. Therm. Anal. Calorim., 135 (2019), pp. 2001-2008 View PDF

CrossRef View Record in Scopus [69]

T. Li, W.D. Griffiths, J. Chen

Metall. Mater. Trans. A-Phys. Metall. Mater. Sci., 48A (2017), pp. 5516-5528 View PDF

CrossRef View Record in Scopus [70]

M. Tiryakioglu, D. Hudak

J. Mater. Sci., 42 (2007), pp. 10173-10179 View PDF

CrossRef View Record in Scopus [71]

Y. Yue, W.D. Griffiths, J.L. Fife, N.R. Green

Proceedings of the 1st International Conference on 3d Materials Science (2012), pp. 131-136 View PDF

CrossRef View Record in Scopus Google Scholar [72]

R. Raiszadeh, W.D. Griffiths

Metall. Mater. Trans. B-Process Metall. Mater. Process. Sci., 37 (2006), pp. 865-871

View Record in Scopus [73]

Z.C. Hu, E.L. Zhang, S.Y. Zeng

Mater. Sci. Technol., 24 (2008), pp. 1304-1308 View PDF

CrossRef View Record in Scopus

원문보기

Numerical study of the dam-break waves and Favre waves down sloped wet rigid-bed at laboratory scale

WenjunLiu^a BoWang^a YakunGuo^b^aState Key Laboratory of Hydraulics and Mountain River Engineering, College of Water Resource and Hydropower, Sichuan University, Chengdu 610065, China^bFaculty of Engineering & Informatics, University of Bradford, BD7 1DP, UK

Highlights

경사진 습윤층에서 댐파괴유동과 FFavre 파를 수치적으로 조사하였다.
수직 대 수평 속도의 비율이 먼저 정량화됩니다.
유동 상태는 유상 경사가 큰 후기 단계에서 크게 변경됩니다.
Favre 파도는 수직 속도와 수직 가속도에 큰 영향을 미칩니다.
베드 전단응력의 변화는 베드 기울기와 꼬리물의 영향을 받습니다.

Abstract

The bed slope and the tailwater depth are two important ones among the factors that affect the propagation of the dam-break flood and Favre waves. Most previous studies have only focused on the macroscopic characteristics of the dam-break flows or Favre waves under the condition of horizontal bed, rather than the internal movement characteristics in sloped channel. The present study applies two numerical models, namely, large eddy simulation (LES) and shallow water equations (SWEs) models embedded in the CFD software package FLOW-3D to analyze the internal movement characteristics of the dam-break flows and Favre waves, such as water level, the velocity distribution, the fluid particles acceleration and the bed shear stress, under the different bed slopes and water depth ratios. The results under the conditions considered in this study show that there is a flow state transition in the flow evolution for the steep bed slope even in water depth ratio α = 0.1 (α is the ratio of the tailwater depth to the reservoir water depth). The flow state transition shows that the wavefront changes from a breaking state to undular. Such flow transition is not observed for the horizontal slope and mild bed slope. The existence of the Favre waves leads to a significant increase of the vertical velocity and the vertical acceleration. In this situation, the SWEs model has poor prediction. Analysis reveals that the variation of the maximum bed shear stress is affected by both the bed slope and tailwater depth. Under the same bed slope (e.g., S₀ = 0.02), the maximum bed shear stress position develops downstream of the dam when α = 0.1, while it develops towards the end of the reservoir when α = 0.7. For the same water depth ratio (e.g., α = 0.7), the maximum bed shear stress position always locates within the reservoir at S₀ = 0.02, while it appears in the downstream of the dam for S₀ = 0 and 0.003 after the flow evolves for a while. The comparison between the numerical simulation and experimental measurements shows that the LES model can predict the internal movement characteristics with satisfactory accuracy. This study improves the understanding of the effect of both the bed slope and the tailwater depth on the internal movement characteristics of the dam-break flows and Favre waves, which also provides a valuable reference for determining the flood embankment height and designing the channel bed anti-scouring facility.

Fig. 1. Sketch of related variables involved in shallow water model.

Fig. 2. Flume model in numerical simulation.

Fig. 3. Grid sensitivity analysis (a) water surface profile; (b) velocity profile.

Fig. 4. Sketch of experimental set-up for validating the velocity profile.

Fig. 5. Sketch of experimental set-up for validating the bed shear stress.

Fig. 6. Model validation results (a) variation of the velocity profile; (b) error value of the velocity profile; (c) variation of the bed shear stress; (d) error value of the bed shear stress.

Fig. 7. Schematic diagram of regional division.

Fig. 8. Variation of water surface profile (a) α = 0.1; (b) α = 0.3; (c) α = 0.5; (d) α = 0.7.

Fig. 9. Froude number for α = 0.1 (a) variation with time; (b) variation with wavefront position.

Fig. 10. Characteristics of velocity distribution (a) α = 0.1; (b) α = 0.3; (c) α = 0.5; (d) α = 0.7.

Fig. 11. Average proportion of the vertical velocity (a) α = 0.1; (b) α = 0.3; (c) α = 0.5; (d) α = 0.7.

Fig. 12. Bed shear stress distribution (a) α = 0.1; (b) α = 0.3; (c) α = 0.5; (d) α = 0.7.

Fig. 13. Variation of the maximum bed shear stress position with time (a) α = 0.1; (b) α = 0.3; (c) α = 0.5; (d) α = 0.7.

Fig. 14. Time when the maximum bed shear stress appears at different positions (a) α = 0.1; (b) α = 0.3; (c) α = 0.5; (d) α = 0.7.

Fig. 15. Movement characteristics of the fluid particles (a) α = 0.1; (b) α = 0.3; (c) α = 0.5; (d) α = 0.7.

Keywords

Dam-break flow, Bed slope, Wet bed, Velocity profile, Bed shear stress, Large eddy simulation

References

Barnes, M.P., Baldock, T.E. 2006. Bed shear stress measurements in dam break and swash
flows. Proceedings of International Conference on Civil and Environmental
Engineering. Hiroshima University, Japan, 28–29 September.
Biscarini, C., Francesco, S.D., Manciola, P., 2010. CFD modelling approach for dam break
flow studies. Hydrol. Earth Syst. Sc. 14, 705–718. https://doi.org/10.5194/hess-14-
705-2010.
Fig. 15. (continued).
W. Liu et al.
Journal of Hydrology 602 (2021) 126752
19
Bristeau, M.-O., Goutal, N., Sainte-Marie, J., 2011. Numerical simulations of a nonhydrostatic shallow water model. Comput. Fluids. 47 (1), 51–64. https://doi.org/
10.1016/j.compfluid.2011.02.013.
Bung, D.B., Hildebrandt, A., Oertel, M., Schlenkhoff, A., Schlurmann, T. 2008. Bore
propagation over a submerged horizontal plate by physical and numerical
simulation. Proc. 31st Intl.Conf. Coastal Eng., Hamburg, Germany, 3542–3553.
Cantero-Chinchilla, F.N., Castro-Orgaz, O., Dey, S., Ayuso, J.L., 2016. Nonhydrostatic
dam break flows. I: physical equations and numerical schemes. J. Hydraul. Eng. 142
(12), 04016068. https://doi.org/10.1061/(ASCE)HY.1943-7900.0001205.
Castro-Orgaz, O., Chanson, H., 2020. Undular and broken surges in dam-break flows: A
review of wave breaking strategies in a boussinesq-type framework. Environ. Fluid
Mech. 154 https://doi.org/10.1007/s10652-020-09749-3.
Chang, T.-J., Kao, H.-M., Chang, K.-H., Hsu, M.-H., 2011. Numerical simulation of
shallow-water dam break flows in open channels using smoothed particle
hydrodynamics. J. Hydrol. 408 (1-2), 78–90. https://doi.org/10.1016/j.
jhydrol.2011.07.023.
Chen, H., Xu, W., Deng, J., Xue, Y., Li, J., 2009. Experimental investigation of pressure
load exerted on a downstream dam by dam-break flow. J. Hydraul. Eng. 140,
199–207. https://doi.org/10.1061/(ASCE)HY.1943-7900.0000743.
Favre H. 1935. Etude th´eorique et exp´erimentale des ondes de translation dans les
canaux d´ecouverts. Dunod, Paris. (in French).
Flow Science Inc. 2016. Flow-3D User’s Manuals. Santa Fe NM.
Fraccarollo, L., Toro, E.F., 1995. Experimental and numerical assessment of the shallow
water model for two-dimensional dam-break type problems. J. Hydraul. Res. 33 (6),
843–864. https://doi.org/10.1080/00221689509498555.
Guo, Y., Wu, X., Pan, C., Zhang, J., 2012. Numerical simulation of the tidal flow and
suspended sediment transport in the qiantang estuary. J Waterw. Port Coastal. 138
(3), 192–202. https://doi.org/10.1061/(ASCE)WW.1943-5460.0000118.
Guo, Y., Zhang, Z., Shi, B., 2014. Numerical simulation of gravity current descending a
slope into a linearly stratified environment. J. Hydraulic Eng. 140 (12), 04014061.
https://doi.org/10.1061/(ASCE)HY.1943-7900.0000936.
Khosronejad, A., Kang, S., Flora, K., 2019. Fully coupled free-surface flow and sediment
transport modelling of flash floods in a desert stream in the mojave desert, california.
Hydrol. Process 33 (21), 2772–2791. https://doi.org/10.1002/hyp.v33.2110.1002/
hyp.13527.
Khosronejad, A., Arabi, M.G., Angelidis, D., Bagherizadeh, E., Flora, K., Farhadzadeh, A.,
2020a. A comparative study of rigid-lid and level-set methods for LES of openchannel flows: morphodynamics. Environ. Fluid Mech. 20 (1), 145–164. https://doi.
org/10.1007/s10652-019-09703-y.
Khosronejad, A., Flora, K., Zhang, Z.X., Kang, S., 2020b. Large-eddy simulation of flash
flood propagation and sediment transport in a dry-bed desert stream. Int. J.
Sediment Res. 35 (6), 576–586. https://doi.org/10.1016/j.ijsrc.2020.02.002.
Khoshkonesh, A., Nsom, B., Gohari, S., Banejad, H., 2019. A comprehensive study of dam
break over the dry and wet beds. Ocean Eng. 188, 106279.1–106279.18. https://doi.
org/10.1016/j.oceaneng.2019.106279.
Kocaman, S., Ozmen-Cagatay, H., 2012. The effect of lateral channel contraction on dam
break flows: laboratory experiment. J. Hydrol. 432–433, 145–153. https://doi.org/
10.1016/j.jhydrol.2012.02.035.
Kocaman, S., Ozmen-Cagatay, H., 2015. Investigation of dam-break induced shock waves
impact on a vertical wall. J. Hydrol. 525, 1–12. https://doi.org/10.1016/j.
jhydrol.2015.03.040.
LaRocque, L.A., Imran, J., Chaudhry, M.H., 2013a. Experimental and numerical
investigations of two-dimensional dam-break flows. J. Hydraul. Eng. 139 (6),
569–579. https://doi.org/10.1061/(ASCE)HY.1943-7900.0000705.
Larocque, L.A., Imran, J., Chaudhry, M.H., 2013b. 3D numerical simulation of partial
breach dam-break flow using the LES and k-ε turbulence models. J. Hydraul. Res. 51,
145–157. https://doi.org/10.1080/00221686.2012.734862.
Lauber, G., Hager, W.H., 1998a. Experiments to dam break wave: Horizontal channel.
J. Hydraul. Res. 36 (3), 291–307. https://doi.org/10.1080/00221689809498620.
Lauber, G., Hager, W.H., 1998b. Experiments to dam break wave: Sloping channel.
J. Hydraul. Res. 36 (5), 761–773. https://doi.org/10.1080/00221689809498601.
Leal, J.G., Ferreira, R.M., Cardoso, A.H., 2006. Dam-break wave-front celerity.
J. Hydraul. Eng. 132 (1), 69–76. https://doi.org/10.1061/(ASCE)0733-9429(2006)
132:1(69).
Liu, W., Wang, B., Guo, Y., Zhang, J., Chen, Y., 2020. Experimental investigation on the
effects of bed slope and tailwater on dam-break flows. J. Hydrol. 590, 125256.
https://doi.org/10.1016/j.jhydrol.2020.125256.
Marche, C., Beauchemin P. EL Kayloubi, A. 1995. Etude num´erique et exp´erimentale des
ondes secondaires de Favre cons´ecutives a la rupture d’un harrage. Can. J. Civil Eng.
22, 793–801, (in French). https://doi.org/10.1139/l95-089.
Marra, D., Earl, T., Ancey, C. 2011. Experimental investigations of dam break flows down
an inclined channel. Proceedings of the 34th World Congress of the International
Association for Hydro-Environment Research and Engineering: 33rd Hydrology and
Water Resources Symposium and 10th Conference on Hydraulics in Water
Engineering, Brisbane, Australia.
Marsooli, R., Wu, W., 2014. 3-D finite-volume model of dam-break flow over uneven
beds based on vof method. Adv. Water Resour. 70, 104–117. https://doi.org/
10.1016/j.advwatres.2014.04.020.
Miller, S., Chaudhry, M.H., 1989. Dam-break flows in curved channel. J. Hydraul. Eng.
115 (11), 1465–1478. https://doi.org/10.1061/(ASCE)0733-9429(1989)115:11
(1465).
Mohapatra, P.K., Chaudhry, M.H., 2004. Numerical solution of Boussinesq equations to
simulate dam-break flows. J. Hydraul. Eng. 130 (2), 156–159. https://doi.org/
10.1061/(ASCE)0733-9429(2004)130:2(156).
Oertel, M., Bung, D.B., 2012. Initial stage of two-dimensional dam-break waves:
laboratory versus VOF. J. Hydraul. Res. 50 (1), 89–97. https://doi.org/10.1080/
00221686.2011.639981.
Ozmen-Cagatay, H., Kocaman, S., 2012. Investigation of dam-break flow over abruptly
contracting channel with trapezoidal-shaped lateral obstacles. J. Fluids Eng. 134,
081204 https://doi.org/10.1115/1.4007154.
Ozmen-Cagatay, H., Kocaman, S., Guzel, H., 2014. Investigation of dam-break flood
waves in a dry channel with a hump. J. Hydro-environ. Res. 8 (3), 304–315. https://
doi.org/10.1016/j.jher.2014.01.005.
Park, I.R., Kim, K.S., Kim, J., Van, S.H., 2012. Numerical investigation of the effects of
turbulence intensity on dam-break flows. Ocean Eng. 42, 176–187. https://doi.org/
10.1016/j.oceaneng.2012.01.005.
Peregrine, D.H., 1966. Calculations of the development of an undular bore. J. Fluid
Mech. 25 (2), 321–330. https://doi.org/10.1017/S0022112066001678.
Savic, L.j., Holly, F.M., 1993. Dam break flood waves computed by modified Godunov
method. J. Hydraul. Res. 31 (2), 187–204. https://doi.org/10.1080/
00221689309498844.
Shigematsu, T., Liu, P., Oda, K., 2004. Numerical modeling of the initial stages of dambreak waves. J. Hydraul. Res. 42 (2), 183–195. https://doi.org/10.1080/
00221686.2004.9628303.
Smagorinsky, J., 1963. General circulation experiments with the primitive equations.
Part I: the basic experiment. Mon. Weather Rev. 91, 99–164. https://doi.org/
10.1126/science.27.693.594.
Soares-Frazao, S., Zech, Y., 2002. Undular bores and secondary waves – Experiments and
hybrid finite-volume modeling. J. Hydraul. Res. 40, 33–43. https://doi.org/
10.1080/00221680209499871.
Stansby, P.K., Chegini, A., Barnes, T.C.D., 1998. The initial stages of dam-break flow.
J. Fluid Mech. 370, 203–220. https://doi.org/10.1017/022112098001918.
Treske, A., 1994. Undular bores (favre-waves) in open channels – experimental studies.
J. Hydraul. Res. 32 (3), 355–370. https://doi.org/10.1080/00221689409498738.
Wang, B., Chen, Y., Wu, C., Dong, J., Ma, X., Song, J., 2016. A semi-analytical approach
for predicting peak discharge of floods caused by embankment dam failures. Hydrol.
Process 30 (20), 3682–3691. https://doi.org/10.1002/hyp.v30.2010.1002/
hyp.10896.
Wang, B., Chen, Y., Wu, C., Peng, Y., Ma, X., Song, J., 2017. Analytical solution of dambreak flood wave propagation in a dry sloped channel with an irregular-shaped
cross-section. J. Hydro-environ. Res. 14, 93–104. https://doi.org/10.1016/j.
jher.2016.11.003.
Wang, B., Chen, Y., Wu, C., Peng, Y., Song, J., Liu, W., Liu, X., 2018. Empirical and semianalytical models for predicting peak outflows caused by embankment dam failures.
J. Hydrol. 562, 692–702. https://doi.org/10.1016/j.jhydrol.2018.05.049.
Wang, B., Zhang, J., Chen, Y., Peng, Y., Liu, X., Liu, W., 2019. Comparison of measured
dam-break flood waves in triangular and rectangular channels. J. Hydrol. 575,
690–703. https://doi.org/10.1016/j.jhydrol.2019.05.081.
Wang, B., Liu, W., Zhang, J., Chen, Y., Wu, C., Peng, Y., Wu, Z., Liu, X., Yang, S., 2020a.
Enhancement of semi-theoretical models for predicting peak discharges in breached
embankment dams. Environ. Fluid Mech. 20 (4), 885–904. https://doi.org/10.1007/
s10652-019-09730-9.
Wang, B., Chen, Y., Peng, Y., Zhang, J., Guo, Y., 2020b. Analytical solution of shallow
water equations for ideal dam-break flood along a wet bed slope. J. Hydraul. Eng.
146 (2), 06019020. https://doi.org/10.1061/(ASCE)HY.1943-7900.0001683.
Wang, B., Liu, W., Wang, W., Zhang, J., Chen, Y., Peng, Y., Liu, X., Yang, S., 2020c.
Experimental and numerical investigations of similarity for dam-break flows on wet
bed. J. Hydrol. 583, 124598. https://doi.org/10.1016/j.jhydrol.2020.124598.
Wang, B., Liu, X., Zhang, J., Guo, Y., Chen, Y., Peng, Y., Liu, W., Yang, S., Zhang, F.,
2020d. Analytical and experimental investigations of dam-break flows in triangular
channels with wet-bed conditions. J. Hydraul. Eng. 146 (10), 04020070. https://doi.
org/10.1061/(ASCE)HY.1943-7900.0001808.
Wu, W., Wang, S., 2007. One-dimensional modeling of dam-break flow over movable
beds. J. Hydraul. Eng. 133 (1), 48–58. https://doi.org/10.1061/(ASCE)0733-9429
(2007)133:1(48).
Xia, J., Lin, B., Falconer, R.A., Wang, G., 2010. Modelling dam-break flows over mobile
beds using a 2d coupled approach. Adv. Water Resour. 33 (2), 171–183. https://doi.
org/10.1016/j.advwatres.2009.11.004.
Yang, S., Yang, W., Qin, S., Li, Q., Yang, B., 2018a. Numerical study on characteristics of
dam-break wave. Ocean Eng. 159, 358–371. https://doi.org/10.1016/j.
oceaneng.2018.04.011.
Yang, S., Yang, W., Qin, S., Li, Q., 2018b. Comparative study on calculation methods of
dam-break wave. J. Hydraul. Res. 57 (5), 702–714. https://doi.org/10.1080/
00221686.2018.1494057.

Figure 3. Comparison of water surface profiles over porous media with 12 mm particle diameter in laboratory measurements (symbols) and numerical results (lines).

다공층에 대한 돌발 댐 붕괴의 3차원 유동 수치해석 시뮬레이션

A. Safarzadeh1*, P. Mohsenzadeh2, S. Abbasi3
1 Professor of Civil Eng., Water Engineering and Mineral Waters Research Center, Univ. of Mohaghegh Ardabili,Ardabil, Iran
2 M.Sc., Graduated of Civil-Hydraulic Structures Eng., Faculty of Eng., Univ. of Mohaghegh Ardabili, Ardabil, Iran
3 M.Sc., Graduated of Civil -Hydraulic Structures Eng., Faculty of Eng., Univ. of Mohaghegh Ardabili, Ardabil, Iran Safarzadeh@uma.ac.ir

Highlights

유체 이동에 의해 생성된 RBF는 Ls-Dyna에서 Fluent, ICFD ALE 및 SPH 방법으로 시뮬레이션되었습니다.
RBF의 과예측은 유체가 메인 도메인에서 고속으로 분리될 때 발생합니다.
이 과잉 예측은 요소 크기, 시간 단계 크기 및 유체 모델에 따라 다릅니다.
유체 성능을 검증하려면 최대 RBF보다 임펄스가 권장됩니다.

Abstract

Dam break is a very important problem due to its effects on economy, security, human casualties and environmental consequences. In this study, 3D flow due to dam break over the porous substrate is numerically simulated and the effect of porosity, permeability and thickness of the porous bed and the water depth in the porous substrate are investigated. Classic models of dam break over a rigid bed and water infiltration through porous media were studied and results of the numerical simulations are compared with existing laboratory data. Validation of the results is performed by comparing the water surface profiles and wave front position with dam break on rigid and porous bed. Results showed that, due to the effect of dynamic wave in the initial stage of dam break, a local peak occurs in the flood hydrograph. The presence of porous bed reduces the acceleration of the flood wave relative to the flow over the solid bed and it decreases with the increase of the permeability of the bed. By increasing the permeability of the bed, the slope of the ascending limb of the flood hydrograph and the peak discharge drops. Furthermore, if the depth and permeability of the bed is such that the intrusive flow reaches the rigid substrate under the porous bed, saturation of the porous bed, results in a sharp increase in the slope of the flood hydrograph. The maximum values of the peak discharge at the end of the channel with porous bed occurred in saturated porous bed conditions.

댐 붕괴는 경제, 보안, 인명 피해 및 환경적 영향으로 인해 매우 중요한 문제입니다. 본 연구에서는 다공성 기재에 대한 댐 파괴로 인한 3차원 유동을 수치적으로 시뮬레이션하고 다공성 기재의 다공성, 투과도 및 다공성 층의 두께 및 수심의 영향을 조사합니다. 단단한 바닥에 대한 댐 파괴 및 다공성 매체를 통한 물 침투의 고전 모델을 연구하고 수치 시뮬레이션 결과를 기존 실험실 데이터와 비교합니다. 결과 검증은 강체 및 다공성 베드에서 댐 파단과 수면 프로파일 및 파면 위치를 비교하여 수행됩니다. 그 결과 댐파괴 초기의 동적파동의 영향으로 홍수수문곡선에서 국부첨두가 발생하는 것으로 나타났다. 다공성 베드의 존재는 고체 베드 위의 유동에 대한 홍수파의 가속을 감소시키고 베드의 투과성이 증가함에 따라 감소합니다. 베드의 투수성을 증가시켜 홍수 수문곡선의 오름차순 경사와 첨두방류량이 감소한다. 더욱이, 만약 층의 깊이와 투과성이 관입 유동이 다공성 층 아래의 단단한 기질에 도달하는 정도라면, 다공성 층의 포화는 홍수 수문곡선의 기울기의 급격한 증가를 초래합니다. 다공층이 있는 채널의 끝단에서 최대 방전 피크값은 포화 다공층 조건에서 발생하였다.

Keywords

Keywords: Dams Break, 3D modeling, Porous Bed, Permeability, Flood wave

Reference

[1] D.L. Fread, In: Maidment, D.R. (Ed.), Flow Routing in Handbook of Hydrology, McGraw-Hill Inc., New York, USA, pp. 10(1) (1993) 1-36.
[2] M. Morris, CADAM: Concerted Action on Dambreak Modeling – Final Report, Rep. SR 571. HR Wallingford, 2000.
[3] H. Chanson, The Hydraulics of Open Channel Flows: an Introduction, ButterworthHeinemann, Oxford, 2004.
[4] A. Ritter, Die Fortpflanzung der Wasserwellen (The Propagation of Water Waves), Zeitschrift Verein Deutscher Ingenieure, 36 (33) (1892) 947–954 [in German].
[5] B. Ghimire, Hydraulic Analysis of Free-Surface Flows into Highly Permeable Porous Media and its Applications, Phd. Thesis, Kyoto University, 2009.
[6] R. Dressler, Hydraulic Resistance Effect Upon the Dam-Break Function, Journal of Research of the National Bureau of Standards, 49 (3) 1952.
[7] G. Lauber, and W.H. Hager, Experiments to Dambreak Wave: horizontal channel, Journal of Hydraulic Research. 36 (3) (1998) 291–307.
[8] L.W. Tan, and V.H. Chu, Lagrangian Block Hydrodynamics of Macro Resistance in a River-Flow Model,
[9] L. Tan, V.H. Lauber and Hager’s Dam-Break Wave Data for Numerical Model Validation, Journal of Hydraulic Research, 47 (4) (2009) 524-528.
[10] S. Mambretti, E.D. Larcan, and D. Wrachien, 1D Modelling of Dam-Break Surges with Floating Debris, J. of Biosystems engineering, 100 (2) (2008) 297-308.
[11] M. Pilotti, M. Tomirotti, G. Valerio, and B. Bacchi, Simplified Method for the Characterization of the Hydrograph Following a Sudden Partial Dam Break, Journal of Hydraulic Engineering, 136 (10) (2010) 693-704.
[12] T.J. Chang, H.M. Kao, K.H. Chang, and Mi.H. Hsu, Numerical Simulation of ShallowWater Dam Break Flows in Open Channels Using Smoothed Particle Hydrodynamics, J. Hydraul. Eng., 408 (78–90) 2011.
[13] T. Tawatchai, and W. Rattanapitikon, 2-D Modelling of Dambreak Wave Propagation on Initially Dry Bed, Thammasat Int. J. Sc. 4 (3) 1999.
[14] Y.F. Le, Experimental Study of landslide Dam-Break Flood over Erodible Bed in open Channels. Journal of Hydrodynamics, Ser. B, 21 (5) 2006.
[15] O. Castro-Orgaz, & H. Chanson, Ritter’s Dry-Bed Dam-Break Flows: Positive and Negative Wave Dynamics, J. of Environmental Fluid Mechanics, 17 (4) (2017) 665-694.
[16] A. Jozdani, A.R. Kabiri-Samani, Application of Image Processing Method to Analysis of Flood Behavior Due to Dam Break, 9th Iranian Hydraulic Conference. Univ. of Tarbiat Moddares, 2011.(in persian)
[17] A. Safarzadeh, Three Dimensional Hydrodynamics of Sudden Dam Break in Curved Channels, Journal of Modares Civil Engineering, 17(3) (2017) 77-86. (in persian)
[18] P. C. Carman, Fluid Flow Through Granular Beds, Transactions, Institution of Chem. Eng. Res. Des. 75 (Dec): S32–S48, London, 15, (1937) 150-166.
[19] P. Forchheimer, Wasserbewegung Durch Boden. Z. Ver. Deutsch. Ing. 45 (1901) 1782– 1788.
[20] S. Ergun, Fluid Flow through Packed Columns. Chemical Engineering Progress, 48(2) (1952) 89-93.
[21] A. Parsaei, S. Dehdar-Behbahani, Numerical Modeling of Cavitation on Spillway’s Flip Bucket, Frontiers of Structural and Civil Engineering, 10 (4) (2016) 438-444.
[22] S. Dehdar-Behbahani, A. Parsaei, Numerical Modeling of Flow Pattern in Dam Spillway’s Guide Wall. Case study: Balaroud dam, Iran, Alexandria Engineering Journal, 55(1) (2016) 467-473.
[23] A. Parsaei, AH. Haghiabi, A. Moradnejad, CFD Modeling of Flow Pattern in Spillway’s ACCEPTED MANUSCRIPT 19 Approach Channel, Sustainable Water Resources Management, 1(3) (2015) 245-251.
[24] SH. Najafian, H. Yonesi, A. Parsaei, PH. Torabi, Physical and Numerical Modeling of Flow in Heterogeneous Roughness Non-Prismatic Compound Open Channel, Irrigation and Drainage Structures Engineering Research, 17(66) (2016) 87-104.
[25] SH. Najafian, H. Yonesi, A. Parsaei, PH. Torabi, Physical and Numerical Modeling of Flow Properties in Prismatic Compound Open Channel with Heterogeneous Roughness, Irrigation and Drainage Structures Engineering Research, 18(68) (2017) 1-16.
[26] A. Safarzadeh, S.H. Mohajeri, Hydrodynamics of Rectangular Broad-Crested Porous Weirs, Journal of Irrig. & Drain. Eng., 144(10) (2018) 1-12.
[27] M. Fathi-moghaddam, M.T. Sadrabadi, M, Rahamnshahi, Numerical Simulation of the Hydraulic Performance of Triangular and Trapezoidal Gabion Weirs in Free Flow Condition, Journal of Flow Measurement & Instrumentation, 62 (2018) 93-104.
[28] A. Parsaei, A. Moradnejad, Numerical Modeling of Flow Pattern in Spillway Approach Channel, Jordan Journal of Civil Engineering, 12(1) (2018) 1-9.

PDF VIEW

Fig. 1 Multi-physics phenomena in the laser-material interaction zone

COMPARISON BETWEEN GREEN AND
INFRARED LASER IN LASER POWDER BED
FUSION OF PURE COPPER THROUGH HIGH
FIDELITY NUMERICAL MODELLING AT MESOSCALE

316-L 스테인리스강의 레이저 분말 베드 융합 중 콜드 스패터 형성의 충실도 높은 수치 모델링

W.E. ALPHONSO¹*, M. BAYAT¹ and J.H. HATTEL¹
*Corresponding author
1Technical University of Denmark (DTU), 2800, Kgs, Lyngby, Denmark

ABSTRACT

L-PBF(Laser Powder Bed Fusion)는 금속 적층 제조(MAM) 기술로, 기존 제조 공정에 비해 부품 설계 자유도, 조립품 통합, 부품 맞춤화 및 낮은 툴링 비용과 같은 여러 이점을 산업에 제공합니다.

전기 코일 및 열 관리 장치는 일반적으로 높은 전기 및 열 전도성 특성으로 인해 순수 구리로 제조됩니다. 따라서 순동의 L-PBF가 가능하다면 기하학적으로 최적화된 방열판과 자유형 전자코일을 제작할 수 있습니다.

그러나 L-PBF로 조밀한 순동 부품을 생산하는 것은 적외선에 대한 낮은 광 흡수율과 높은 열전도율로 인해 어렵습니다. 기존의 L-PBF 시스템에서 조밀한 구리 부품을 생산하려면 적외선 레이저의 출력을 500W 이상으로 높이거나 구리의 광흡수율이 높은 녹색 레이저를 사용해야 합니다.

적외선 레이저 출력을 높이면 후면 반사로 인해 레이저 시스템의 광학 구성 요소가 손상되고 렌즈의 열 광학 현상으로 인해 공정이 불안정해질 수 있습니다. 이 작업에서 FVM(Finite Volume Method)에 기반한 다중 물리학 중간 규모 수치 모델은 Flow-3D에서 개발되어 용융 풀 역학과 궁극적으로 부품 품질을 제어하는 물리적 현상 상호 작용을 조사합니다.

녹색 레이저 열원과 적외선 레이저 열원은 기판 위의 순수 구리 분말 베드에 단일 트랙 증착을 생성하기 위해 개별적으로 사용됩니다.

용융 풀 역학에 대한 레이저 열원의 유사하지 않은 광학 흡수 특성의 영향이 탐구됩니다. 수치 모델을 검증하기 위해 단일 트랙이 구리 분말 베드에 증착되고 시뮬레이션된 용융 풀 모양과 크기가 비교되는 실험이 수행되었습니다.

녹색 레이저는 광흡수율이 높아 전도 및 키홀 모드 용융이 가능하고 적외선 레이저는 흡수율이 낮아 키홀 모드 용융만 가능하다. 레이저 파장에 대한 용융 모드의 변화는 궁극적으로 기계적, 전기적 및 열적 특성에 영향을 미치는 열 구배 및 냉각 속도에 대한 결과를 가져옵니다.

Laser Powder Bed Fusion (L-PBF) is a Metal Additive Manufacturing (MAM) technology which offers several advantages to industries such as part design freedom, consolidation of assemblies, part customization and low tooling cost over conventional manufacturing processes. Electric coils and thermal management devices are generally manufactured from pure copper due to its high electrical and thermal conductivity properties. Therefore, if L-PBF of pure copper is feasible, geometrically optimized heat sinks and free-form electromagnetic coils can be manufactured. However, producing dense pure copper parts by L-PBF is difficult due to low optical absorptivity to infrared radiation and high thermal conductivity. To produce dense copper parts in a conventional L-PBF system either the power of the infrared laser must be increased above 500W, or a green laser should be used for which copper has a high optical absorptivity. Increasing the infrared laser power can damage the optical components of the laser systems due to back reflections and create instabilities in the process due to thermal-optical phenomenon of the lenses. In this work, a multi-physics meso-scale numerical model based on Finite Volume Method (FVM) is developed in Flow-3D to investigate the physical phenomena interaction which governs the melt pool dynamics and ultimately the part quality. A green laser heat source and an infrared laser heat source are used individually to create single track deposition on pure copper powder bed above a substrate. The effect of the dissimilar optical absorptivity property of laser heat sources on the melt pool dynamics is explored. To validate the numerical model, experiments were conducted wherein single tracks are deposited on a copper powder bed and the simulated melt pool shape and size are compared. As the green laser has a high optical absorptivity, a conduction and keyhole mode melting is possible while for the infrared laser only keyhole mode melting is possible due to low absorptivity. The variation in melting modes with respect to the laser wavelength has an outcome on thermal gradient and cooling rates which ultimately affect the mechanical, electrical, and thermal properties.

Keywords

Pure Copper, Laser Powder Bed Fusion, Finite Volume Method, multi-physics

Fig. 2 Framework for single laser track simulation model including powder bed and substrate (a) computational domain with boundaries (b) discretization of the domain with uniform quad mesh.

Fig. 3 2D melt pool contours from the numerical model compared to experiments [16] for (a) VED = 65 J/mm3 at 7 mm from the beginning of the single track (b) VED = 103 J/mm3 at 3 mm from the beginning of the single track (c) VED = 103 J/mm3 at 7 mm from the beginning of the single track. In the 2D contour, the non-melted region is indicated in blue, and the melted region is indicated by red and green when the VED is 65 J/mm3 and 103 J/mm3 respectively.

Fig. 4 3D temperature contour plots of during single track L-PBF process at time1.8 µs when (a) VED = 65 J/mm3 (b) VED = 103 J/mm3 along with 2D melt pool contours at 5 mm from the laser initial position. In the 2D contour, the non-melted region is indicated in blue, and the melted region is indicated by red and green when the VED is 65 J/mm3 and 103 J/mm3 respectively.

References

[1] L. Jyothish Kumar, P. M. Pandey, and D. I. Wimpenny, 3D printing and additive
manufacturing technologies. Springer Singapore, 2018. doi: 10.1007/978-981-13-0305-0.
[2] T. DebRoy et al., “Additive manufacturing of metallic components – Process, structure
and properties,” Progress in Materials Science, vol. 92, pp. 112–224, 2018, doi:
10.1016/j.pmatsci.2017.10.001.
[3] C. S. Lefky, B. Zucker, D. Wright, A. R. Nassar, T. W. Simpson, and O. J. Hildreth,
“Dissolvable Supports in Powder Bed Fusion-Printed Stainless Steel,” 3D Printing and
Additive Manufacturing, vol. 4, no. 1, pp. 3–11, 2017, doi: 10.1089/3dp.2016.0043.
[4] J. L. Bartlett and X. Li, “An overview of residual stresses in metal powder bed fusion,”
Additive Manufacturing, vol. 27, no. January, pp. 131–149, 2019, doi:
10.1016/j.addma.2019.02.020.
[5] I. H. Ahn, “Determination of a process window with consideration of effective layer
thickness in SLM process,” International Journal of Advanced Manufacturing
Technology, vol. 105, no. 10, pp. 4181–4191, 2019, doi: 10.1007/s00170-019-04402-w.

[6] R. McCann et al., “In-situ sensing, process monitoring and machine control in Laser
Powder Bed Fusion: A review,” Additive Manufacturing, vol. 45, no. May, 2021, doi:
10.1016/j.addma.2021.102058.
[7] M. Bayat et al., “Keyhole-induced porosities in Laser-based Powder Bed Fusion (L-PBF)
of Ti6Al4V: High-fidelity modelling and experimental validation,” Additive
Manufacturing, vol. 30, no. August, p. 100835, 2019, doi: 10.1016/j.addma.2019.100835.
[8] M. Bayat, S. Mohanty, and J. H. Hattel, “Multiphysics modelling of lack-of-fusion voids
formation and evolution in IN718 made by multi-track/multi-layer L-PBF,” International
Journal of Heat and Mass Transfer, vol. 139, pp. 95–114, 2019, doi:
10.1016/j.ijheatmasstransfer.2019.05.003.
[9] S. D. Jadhav, L. R. Goossens, Y. Kinds, B. van Hooreweder, and K. Vanmeensel, “Laserbased powder bed fusion additive manufacturing of pure copper,” Additive Manufacturing,
vol. 42, no. March, 2021, doi: 10.1016/j.addma.2021.101990.
[10] S. D. Jadhav, S. Dadbakhsh, L. Goossens, J. P. Kruth, J. van Humbeeck, and K.
Vanmeensel, “Influence of selective laser melting process parameters on texture evolution
in pure copper,” Journal of Materials Processing Technology, vol. 270, no. January, pp.
47–58, 2019, doi: 10.1016/j.jmatprotec.2019.02.022.
[11] H. Siva Prasad, F. Brueckner, J. Volpp, and A. F. H. Kaplan, “Laser metal deposition of
copper on diverse metals using green laser sources,” International Journal of Advanced
Manufacturing Technology, vol. 107, no. 3–4, pp. 1559–1568, 2020, doi: 10.1007/s00170-
020-05117-z.
[12] L. R. Goossens, Y. Kinds, J. P. Kruth, and B. van Hooreweder, “On the influence of
thermal lensing during selective laser melting,” Solid Freeform Fabrication 2018:
Proceedings of the 29th Annual International Solid Freeform Fabrication Symposium – An
Additive Manufacturing Conference, SFF 2018, no. December, pp. 2267–2274, 2020.
[13] M. Bayat, V. K. Nadimpalli, D. B. Pedersen, and J. H. Hattel, “A fundamental investigation
of thermo-capillarity in laser powder bed fusion of metals and alloys,” International
Journal of Heat and Mass Transfer, vol. 166, p. 120766, 2021, doi:
10.1016/j.ijheatmasstransfer.2020.120766.
[14] H. Chen, Q. Wei, Y. Zhang, F. Chen, Y. Shi, and W. Yan, “Powder-spreading mechanisms
in powder-bed-based additive manufacturing: Experiments and computational modeling,”
Acta Materialia, vol. 179, pp. 158–171, 2019, doi: 10.1016/j.actamat.2019.08.030.
[15] S. K. Nayak, S. K. Mishra, C. P. Paul, A. N. Jinoop, and K. S. Bindra, “Effect of energy
density on laser powder bed fusion built single tracks and thin wall structures with 100 µm
preplaced powder layer thickness,” Optics and Laser Technology, vol. 125, May 2020, doi:
10.1016/j.optlastec.2019.106016.
[16] G. Nordet et al., “Absorptivity measurements during laser powder bed fusion of pure
copper with a 1 kW cw green laser,” Optics & Laser Technology, vol. 147, no. April 2021,
p. 107612, 2022, doi: 10.1016/j.optlastec.2021.107612.
[17] M. Hummel, C. Schöler, A. Häusler, A. Gillner, and R. Poprawe, “New approaches on
laser micro welding of copper by using a laser beam source with a wavelength of 450 nm,”
Journal of Advanced Joining Processes, vol. 1, no. February, p. 100012, 2020, doi:
10.1016/j.jajp.2020.100012.
[18] M. Hummel, M. Külkens, C. Schöler, W. Schulz, and A. Gillner, “In situ X-ray
tomography investigations on laser welding of copper with 515 and 1030 nm laser beam
sources,” Journal of Manufacturing Processes, vol. 67, no. April, pp. 170–176, 2021, doi:
10.1016/j.jmapro.2021.04.063.
[19] L. Gargalis et al., “Determining processing behaviour of pure Cu in laser powder bed
fusion using direct micro-calorimetry,” Journal of Materials Processing Technology, vol.
294, no. March, p. 117130, 2021, doi: 10.1016/j.jmatprotec.2021.117130.
[20] A. Mondal, D. Agrawal, and A. Upadhyaya, “Microwave heating of pure copper powder
with varying particle size and porosity,” Journal of Microwave Power and
Electromagnetic Energy, vol. 43, no. 1, pp. 4315–43110, 2009, doi:
10.1080/08327823.2008.11688599.

PDF 원문보기

Fig 3. Front view of the ejected powder particles due to the plume movement. Powder particles are colored by their respective temperature while trajectory colors show their magnitude at 0.007 seconds.

316-L 스테인리스강의 레이저 분말 베드 융합 중 콜드 스패터 형성의 충실도 높은 수치 모델링

M. BAYAT1,* , AND J. H. HATTEL1

Corresponding author
1 Technical University of Denmark (DTU), Building 425, Kgs. 2800 Lyngby, Denmark

ABSTRACT

Spatter and denudation are two very well-known phenomena occurring mainly during the laser powder bed fusion process and are defined as ejection and displacement of powder particles, respectively. The main driver of this phenomenon is the formation of a vapor plume jet that is caused by the vaporization of the melt pool which is subjected to the laser beam. In this work, a 3-dimensional transient turbulent computational fluid dynamics model coupled with a discrete element model is developed in the finite volume-based commercial software package Flow-3D AM to simulate the spatter phenomenon. The numerical results show that a localized low-pressure zone forms at the bottom side of the plume jet and this leads to a pseudo-Bernoulli effect that drags nearby powder particles into the area of influence of the vapor plume jet. As a result, the vapor plume acts like a momentum sink and therefore all nearby particles point are dragged towards this region. Furthermore, it is noted that due to the jet’s attenuation, powder particles start diverging from the central core region of the vapor plume as they move vertically upwards. It is moreover observed that only particles which are in the very central core region of the plume jet get sufficiently accelerated to depart the computational domain, while the rest of the dragged particles, especially those which undergo an early divergence from the jet axis, get stalled pretty fast as they come in contact with the resting fluid. In the last part of the work, two simulations with two different scanning speeds are carried out, where it is clearly observed that the angle between the departing powder particles and the vertical axis of the plume jet increases with increasing scanning speed.

스패터와 denudation은 주로 레이저 분말 베드 융합 과정에서 발생하는 매우 잘 알려진 두 가지 현상으로 각각 분말 입자의 배출 및 변위로 정의됩니다.

이 현상의 주요 동인은 레이저 빔을 받는 용융 풀의 기화로 인해 발생하는 증기 기둥 제트의 형성입니다. 이 작업에서 이산 요소 모델과 결합된 3차원 과도 난류 전산 유체 역학 모델은 스패터 현상을 시뮬레이션하기 위해 유한 체적 기반 상용 소프트웨어 패키지 Flow-3D AM에서 개발되었습니다.

수치적 결과는 플룸 제트의 바닥면에 국부적인 저압 영역이 형성되고, 이는 근처의 분말 입자를 증기 플룸 제트의 영향 영역으로 끌어들이는 의사-베르누이 효과로 이어진다는 것을 보여줍니다.

결과적으로 증기 기둥은 운동량 흡수원처럼 작용하므로 근처의 모든 입자 지점이 이 영역으로 끌립니다. 또한 제트의 감쇠로 인해 분말 입자가 수직으로 위쪽으로 이동할 때 증기 기둥의 중심 코어 영역에서 발산하기 시작합니다.

더욱이 플룸 제트의 가장 중심 코어 영역에 있는 입자만 계산 영역을 벗어날 만큼 충분히 가속되는 반면, 드래그된 나머지 입자, 특히 제트 축에서 초기 발산을 겪는 입자는 정체되는 것으로 관찰됩니다. 그들은 휴식 유체와 접촉하기 때문에 꽤 빠릅니다.

작업의 마지막 부분에서 두 가지 다른 스캔 속도를 가진 두 가지 시뮬레이션이 수행되었으며, 여기서 출발하는 분말 입자와 연기 제트의 수직 축 사이의 각도가 스캔 속도가 증가함에 따라 증가하는 것이 명확하게 관찰되었습니다.

Fig 1. Two different views of the computational domain for the fluid domain. The vapor plume is simulated by a moving momentum source with a prescribed temperature of 3000 K.

Fig 2. (a) and (b) are two snapshots taken at an x-y plane parallel to the powder layer plane before and 0.008 seconds after the start of the scanning process. (c) Shows a magnified view of (b) where detailed powder particles' movement along with their velocity magnitude and directions are shown. — Fig 2. (a) and (b) are two snapshots taken at an x-y plane parallel to the powder layer plane before and 0.008 seconds after the start of the scanning process. (c) Shows a magnified view of (b) where detailed powder particles’ movement along with their velocity magnitude and directions are shown.

References

[1] T. DebRoy et al., “Additive manufacturing of metallic components – Process, structure
and properties,” Prog. Mater. Sci., vol. 92, pp. 112–224, 2018, doi:
10.1016/j.pmatsci.2017.10.001.
[2] M. Markl and C. Körner, “Multiscale Modeling of Powder Bed–Based Additive
Manufacturing,” Annu. Rev. Mater. Res., vol. 46, no. 1, pp. 93–123, 2016, doi:
10.1146/annurev-matsci-070115-032158.
[3] A. Zinoviev, O. Zinovieva, V. Ploshikhin, V. Romanova, and R. Balokhonov, “Evolution
of grain structure during laser additive manufacturing. Simulation by a cellular automata
method,” Mater. Des., vol. 106, pp. 321–329, 2016, doi: 10.1016/j.matdes.2016.05.125.
[4] Y. Zhang and J. Zhang, “Modeling of solidification microstructure evolution in laser
powder bed fusion fabricated 316L stainless steel using combined computational fluid
dynamics and cellular automata,” Addit. Manuf., vol. 28, no. July 2018, pp. 750–765,
2019, doi: 10.1016/j.addma.2019.06.024.
[5] A. A. Martin et al., “Ultrafast dynamics of laser-metal interactions in additive
manufacturing alloys captured by in situ X-ray imaging,” Mater. Today Adv., vol. 1, p.
100002, 2019, doi: 10.1016/j.mtadv.2019.01.001.
[6] Y. C. Wu et al., “Numerical modeling of melt-pool behavior in selective laser melting
with random powder distribution and experimental validation,” J. Mater. Process.
Technol., vol. 254, no. July 2017, pp. 72–78, 2018, doi:
10.1016/j.jmatprotec.2017.11.032.
[7] W. Gao, S. Zhao, Y. Wang, Z. Zhang, F. Liu, and X. Lin, “Numerical simulation of
thermal field and Fe-based coating doped Ti,” Int. J. Heat Mass Transf., vol. 92, pp. 83–
90, 2016, doi: 10.1016/j.ijheatmasstransfer.2015.08.082.
[8] A. Charles, M. Bayat, A. Elkaseer, L. Thijs, J. H. Hattel, and S. Scholz, “Elucidation of
dross formation in laser powder bed fusion at down-facing surfaces: Phenomenonoriented multiphysics simulation and experimental validation,” Addit. Manuf., vol. 50,
2022, doi: 10.1016/j.addma.2021.102551.
[9] C. Meier, R. W. Penny, Y. Zou, J. S. Gibbs, and A. J. Hart, “Thermophysical phenomena
in metal additive manufacturing by selective laser melting: Fundamentals, modeling,
simulation and experimentation,” arXiv, 2017, doi:
10.1615/annualrevheattransfer.2018019042.
[10] W. King, A. T. Anderson, R. M. Ferencz, N. E. Hodge, C. Kamath, and S. A. Khairallah,
“Overview of modelling and simulation of metal powder bed fusion process at Lawrence
Livermore National Laboratory,” Mater. Sci. Technol. (United Kingdom), vol. 31, no. 8,
pp. 957–968, 2015, doi: 10.1179/1743284714Y.0000000728.

PDF 원문보기

Fig. 1. Schematic figure showing the PREP with additional gas flowing on the end face of electrode.

플라즈마 회전 전극 공정 중 분말 형성에 대한 공정 매개변수 및 냉각 가스의 영향

Yujie Cui^a Yufan Zhao^a1Haruko Numata^b Kenta Yamanaka^a Huakang Bian^aKenta Aoyagi^aAkihikoChiba^a
^aInstitute for Materials Research, Tohoku University, Sendai 980-8577, Japan^bDepartment of Materials Processing, Graduate School of Engineering, Tohoku University, Sendai 980-8577, Japan

Highlights

•The limitation of increasing the rotational speed in decreasing powder size was clarified.

•Cooling and disturbance effects varied with the gas flowing rate.

•Inclined angle of the residual electrode end face affected powder formation.

•Additional cooling gas flowing could be applied to control powder size.

Abstract

The plasma rotating electrode process (PREP) is rapidly becoming an important powder fabrication method in additive manufacturing. However, the low production rate of fine PREP powder limits the development of PREP. Herein, we investigated different factors affecting powder formation during PREP by combining experimental methods and numerical simulations. The limitation of increasing the rotation electrode speed in decreasing powder size is attributed to the increased probability of adjacent droplets recombining and the decreased tendency of granulation. The effects of additional Ar/He gas flowing on the rotational electrode on powder formation is determined through the cooling effect, the disturbance effect, and the inclined effect of the residual electrode end face simultaneously. A smaller-sized powder was obtained in the He atmosphere owing to the larger inclined angle of the residual electrode end face compared to the Ar atmosphere. Our research highlights the route for the fabrication of smaller-sized powders using PREP.

플라즈마 회전 전극 공정(PREP)은 적층 제조 에서 중요한 분말 제조 방법으로 빠르게 자리잡고 있습니다. 그러나 미세한 PREP 분말의 낮은 생산율은 PREP의 개발을 제한합니다. 여기에서 우리는 실험 방법과 수치 시뮬레이션을 결합하여 PREP 동안 분말 형성에 영향을 미치는 다양한 요인을 조사했습니다. 분말 크기 감소에서 회전 전극 속도 증가의 한계는 인접한 액적 재결합 확률 증가 및 과립화 경향 감소에 기인합니다.. 회전 전극에 흐르는 추가 Ar/He 가스가 분말 형성에 미치는 영향은 냉각 효과, 외란 효과 및 잔류 전극 단면의 경사 효과를 통해 동시에 결정됩니다. He 분위기에서는 Ar 분위기에 비해 잔류 전극 단면의 경사각이 크기 때문에 더 작은 크기의 분말이 얻어졌다. 우리의 연구는 PREP를 사용하여 더 작은 크기의 분말을 제조하는 경로를 강조합니다.

Keywords

Plasma rotating electrode process

Ti-6Al-4 V alloy, Rotating speed, Numerical simulation, Gas flowing, Powder size

Introduction

With the development of additive manufacturing, there has been a significant increase in high-quality powder production demand [1,2]. The initial powder characteristics are closely related to the uniform powder spreading [3,4], packing density [5], and layer thickness observed during additive manufacturing [6], thus determining the mechanical properties of the additive manufactured parts [7,8]. Gas atomization (GA) [9–11], centrifugal atomization (CA) [12–15], and the plasma rotating electrode process (PREP) are three important powder fabrication methods.

Currently, GA is the dominant powder fabrication method used in additive manufacturing [16] for the fabrication of a wide range of alloys [11]. GA produces powders by impinging a liquid metal stream to droplets through a high-speed gas flow of nitrogen, argon, or helium. With relatively low energy consumption and a high fraction of fine powders, GA has become the most popular powder manufacturing technology for AM.

The entrapped gas pores are generally formed in the powder after solidification during GA, in which the molten metal is impacted by a high-speed atomization gas jet. In addition, satellites are formed in GA powder when fine particles adhere to partially molten particles.

The gas pores of GA powder result in porosity generation in the additive manufactured parts, which in turn deteriorates its mechanical properties because pores can become crack initiation sites [17]. In CA, a molten metal stream is poured directly onto an atomizer disc spinning at a high rotational speed. A thin film is formed on the surface of the disc, which breaks into small droplets due to the centrifugal force. Metal powder is obtained when these droplets solidify.

Compared with GA powder, CA powder exhibits higher sphericity, lower impurity content, fewer satellites, and narrower particle size distribution [12]. However, very high speed is required to obtain fine powder by CA. In PREP, the molten metal, melted using the plasma arc, is ejected from the rotating rod through centrifugal force. Compared with GA powder, PREP-produced powders also have higher sphericity and fewer pores and satellites [18].

For instance, PREP-fabricated Ti6Al-4 V alloy powder with a powder size below 150 μm exhibits lower porosity than gas-atomized powder [19], which decreases the porosity of additive manufactured parts. Furthermore, the process window during electron beam melting was broadened using PREP powder compared to GA powder in Inconel 718 alloy [20] owing to the higher sphericity of the PREP powder.

In summary, PREP powder exhibits many advantages and is highly recommended for powder-based additive manufacturing and direct energy deposition-type additive manufacturing. However, the low production rate of fine PREP powder limits the widespread application of PREP powder in additive manufacturing.

Although increasing the rotating speed is an effective method to decrease the powder size [21,22], the reduction in powder size becomes smaller with the increased rotating speed [23]. The occurrence of limiting effects has not been fully clarified yet.

Moreover, the powder size can be decreased by increasing the rotating electrode diameter [24]. However, these methods are quite demanding for the PREP equipment. For instance, it is costly to revise the PREP equipment to meet the demand of further increasing the rotating speed or electrode diameter.

Accordingly, more feasible methods should be developed to further decrease the PREP powder size. Another factor that influences powder formation is the melting rate [25]. It has been reported that increasing the melting rate decreases the powder size of Inconel 718 alloy [26].

In contrast, the powder size of SUS316 alloy was decreased by decreasing the plasma current within certain ranges. This was ascribed to the formation of larger-sized droplets from fluid strips with increased thickness and spatial density at higher plasma currents [27]. The powder size of NiTi alloy also decreases at lower melting rates [28]. Consequently, altering the melting rate, varied with the plasma current, is expected to regulate the PREP powder size.

Furthermore, gas flowing has a significant influence on powder formation [27,29–31]. On one hand, the disturbance effect of gas flowing promotes fluid granulation, which in turn contributes to the formation of smaller-sized powder [27]. On the other hand, the cooling effect of gas flowing facilitates the formation of large-sized powder due to increased viscosity and surface tension. However, there is a lack of systematic research on the effect of different gas flowing on powder formation during PREP.

Herein, the authors systematically studied the effects of rotating speed, electrode diameter, plasma current, and gas flowing on the formation of Ti-6Al-4 V alloy powder during PREP as additive manufactured Ti-6Al-4 V alloy exhibits great application potential [32]. Numerical simulations were conducted to explain why increasing the rotating speed is not effective in decreasing powder size when the rotation speed reaches a certain level. In addition, the different factors incited by the Ar/He gas flowing on powder formation were clarified.

References

[1] W. Ding, G. Chen, M. Qin, Y. He, X. Qu, Low-cost Ti powders for additive manufacturing treated by fluidized bed, Powder Technol. 350 (2019) 117–122, https://doi.org/
10.1016/j.powtec.2019.03.042.
[2] W.S.W. Harun, M.S.I.N. Kamariah, N. Muhamad, S.A.C. Ghani, F. Ahmad, Z. Mohamed,
A review of powder additive manufacturing processes for metallic biomaterials,
Powder Technol. 327 (2018) 128–151, https://doi.org/10.1016/j.powtec.2017.12.
058.
[3] M. Ahmed, M. Pasha, W. Nan, M. Ghadiri, A simple method for assessing powder
spreadability for additive manufacturing, Powder Technol. 367 (2020) 671–679,
https://doi.org/10.1016/j.powtec.2020.04.033.
[4] W. Nan, M. Pasha, M. Ghadiri, Numerical simulation of particle flow and segregation
during roller spreading process in additive manufacturing, Powder Technol. 364
(2020) 811–821, https://doi.org/10.1016/j.powtec.2019.12.023.
[5] A. Averardi, C. Cola, S.E. Zeltmann, N. Gupta, Effect of particle size distribution on the
packing of powder beds : a critical discussion relevant to additive manufacturing,
Mater. Today Commun. 24 (2020) 100964, https://doi.org/10.1016/j.mtcomm.
2020.100964.
[6] K. Riener, N. Albrecht, S. Ziegelmeier, R. Ramakrishnan, L. Haferkamp, A.B. Spierings,
G.J. Leichtfried, Influence of particle size distribution and morphology on the properties of the powder feedstock as well as of AlSi10Mg parts produced by laser powder bed fusion (LPBF), Addit. Manuf. 34 (2020) 101286, https://doi.org/10.1016/j.
addma.2020.101286.
[7] W.S.W. Harun, N.S. Manam, M.S.I.N. Kamariah, S. Sharif, A.H. Zulkifly, I. Ahmad, H.
Miura, A review of powdered additive manufacturing techniques for Ti-6Al-4V biomedical applications, Powder Technol. 331 (2018) 74–97, https://doi.org/10.1016/j.
powtec.2018.03.010.
[8] A.T. Sutton, C.S. Kriewall, M.C. Leu, J.W. Newkirk, Powder characterisation techniques and effects of powder characteristics on part properties in powder-bed fusion processes, Virtual Phys. Prototyp. 12 (2017) (2017) 3–29, https://doi.org/10.
1080/17452759.2016.1250605.
[9] G. Chen, Q. Zhou, S.Y. Zhao, J.O. Yin, P. Tan, Z.F. Li, Y. Ge, J. Wang, H.P. Tang, A pore
morphological study of gas-atomized Ti-6Al-4V powders by scanning electron microscopy and synchrotron X-ray computed tomography, Powder Technol. 330
(2018) 425–430, https://doi.org/10.1016/j.powtec.2018.02.053.
[10] Y. Feng, T. Qiu, Preparation, characterization and microwave absorbing properties of
FeNi alloy prepared by gas atomization method, J. Alloys Compd. 513 (2012)
455–459, https://doi.org/10.1016/j.jallcom.2011.10.079.

[11] I.E. Anderson, R.L. Terpstra, Progress toward gas atomization processing with increased uniformity and control, Mater. Sci. Eng. A 326 (2002) 101–109, https://
doi.org/10.1016/S0921-5093(01)01427-7.
[12] P. Phairote, T. Plookphol, S. Wisutmethangoon, Design and development of a centrifugal atomizer for producing zinc metal powder, Int. J. Appl. Phys. Math. 2 (2012)
77–82, https://doi.org/10.7763/IJAPM.2012.V2.58.
[13] L. Tian, I. Anderson, T. Riedemann, A. Russell, Production of fine calcium powders by
centrifugal atomization with rotating quench bath, Powder Technol. 308 (2017)
84–93, https://doi.org/10.1016/j.powtec.2016.12.011.
[14] M. Eslamian, J. Rak, N. Ashgriz, Preparation of aluminum/silicon carbide metal matrix composites using centrifugal atomization, Powder Technol. 184 (2008) 11–20,
https://doi.org/10.1016/j.powtec.2007.07.045.
[15] T. Plookphol, S. Wisutmethangoon, S. Gonsrang, Influence of process parameters on
SAC305 lead-free solder powder produced by centrifugal atomization, Powder
Technol. 214 (2011) 506–512, https://doi.org/10.1016/j.powtec.2011.09.015.
[16] M.Z. Gao, B. Ludwig, T.A. Palmer, Impact of atomization gas on characteristics of austenitic stainless steel powder feedstocks for additive manufacturing, Powder
Technol. 383 (2021) 30–42, https://doi.org/10.1016/j.powtec.2020.12.005.
[17] X. Shui, K. Yamanaka, M. Mori, Y. Nagata, A. Chiba, Effects of post-processing on cyclic fatigue response of a titanium alloy additively manufactured by electron beam
melting, Mater. Sci. Eng. A 680 (2017) 239–248, https://doi.org/10.1016/j.msea.
2016.10.059.
[18] C. Wang, X.H. Zhao, Y.C. Ma, Q.X. Wang, Y.J. Lai, S.J. Liang, Study of the spherical
HoCu powders prepared by supreme-speed plasma rotating electrode process,
Powder Metallurgy Technology 38 (3) (2020) 227–233, https://doi.org/10.19591/
j.cnki.cn11-1974/tf.2020.03.011 (in Chinese).
[19] G. Chen, S.Y. Zhao, P. Tan, J. Wang, C.S. Xiang, H.P. Tang, A comparative study of Ti6Al-4V powders for additive manufacturing by gas atomization, plasma rotating
electrode process and plasma atomization, Powder Technol. 333 (2018) 38–46,
https://doi.org/10.1016/j.powtec.2018.04.013.
[20] Y. Zhao, K. Aoyagi, Y. Daino, K. Yamanaka, A. Chiba, Significance of powder feedstock
characteristics in defect suppression of additively manufactured Inconel 718, Addit.
Manuf. 34 (2020) 101277, https://doi.org/10.1016/j.addma.2020.101277.
[21] Y. Nie, J. Tang, B. Yang, Q. Lei, S. Yu, Y. Li, Comparison in characteristic and atomization behavior of metallic powders produced by plasma rotating electrode process,
Adv. Powder Technol. 31 (2020) 2152–2160, https://doi.org/10.1016/j.apt.2020.03.
006.
[22] Y. Cui, Y. Zhao, H. Numata, H. Bian, K. Wako, K. Yamanaka, K. Aoyagi, C. Zhang, A.
Chiba, Effects of plasma rotating electrode process parameters on the particle size
distribution and microstructure of Ti-6Al-4 V alloy powder, Powder Technol 376
(2020) 363–372, https://doi.org/10.1016/j.powtec.2020.08.027.
[23] J. Tang, Y. Nie, Q. Lei, Y. Li, Characteristics and atomization behavior of Ti-6Al-4V
powder produced by plasma rotating electrode process Adv, Powder Technol. 10
(2019) 2330–2337, https://doi.org/10.1016/j.apt.2019.07.015.
[24] M. Zdujić, D. Uskoković, Production of atomized metal and alloy powders by the rotating electrode process, Sov. Powder Metall. Met. Ceram. 29 (1990) 673–683,
https://doi.org/10.1007/BF00795571.
[25] L. Zhang, Y. Zhao, Particle size distribution of tin powder produced by centrifugal
atomisation using rotating cups, Powder Technol. 318 (2017) 62–67, https://doi.
org/10.1016/j.powtec.2017.05.038.
[26] Y. Liu, S. Liang, Z. Han, J. Song, Q. Wang, A novel model of calculating particle sizes in
plasma rotating electrode process for superalloys, Powder Technol. 336 (2018)
406–414, https://doi.org/10.1016/j.powtec.2018.06.002.
[27] Y. Zhao, Y. Cui, H. Numata, H. Bian, K. Wako, K. Yamanaka, Centrifugal granulation
behavior in metallic powder fabrication by plasma rotating electrode process, Sci.
Rep. (2020) 1–15, https://doi.org/10.1038/s41598-020-75503-w.
[28] T. Hsu, C. Wei, L. Wu, Y. Li, A. Chiba, M. Tsai, Nitinol powders generate from plasma
rotation electrode process provide clean powder for biomedical devices used with
suitable size, spheroid surface and pure composition, Sci. Rep. 8 (2018) 1–8,
https://doi.org/10.1038/s41598-018-32101-1.
[29] M. Wei, S. Chen, M. Sun, J. Liang, C. Liu, M. Wang, Atomization simulation and preparation of 24CrNiMoY alloy steel powder using VIGA technology at high gas pressure, Powder Technol. 367 (2020) 724–739, https://doi.org/10.1016/j.powtec.
2020.04.030.
[30] Y. Tan, X. Zhu, X.Y. He, B. Ding, H. Wang, Q. Liao, H. Li, Granulation characteristics of
molten blast furnace slag by hybrid centrifugal-air blast technique, Powder Technol.
323 (2018) 176–185, https://doi.org/10.1016/j.powtec.2017.09.040.
[31] P. Xu, D.H. Liu, J. Hu, G.Y. Lin, Synthesis of Ni-Ti composite powder by radio frequency plasma spheroidization process, Nonferrous Metals Science and Engineering
39 (1) (2020) 67–71 , (in Chinese) 10.13264/j.cnki.ysjskx.2020.01.011.
[32] H. Mehboob, F. Tarlochan, A. Mehboob, S.H. Chang, S. Ramesh, W.S.W. Harun, K.
Kadirgama, A novel design, analysis and 3D printing of Ti-6Al-4V alloy bioinspired porous femoral stem, J. Mater. Sci. Mater. Med. 31 (2020) 78, https://doi.
org/10.1007/s10856-020-06420-7.
[33] FLOW-3D® Version 11.2 [Computer software]. , Flow Science, Inc., Santa Fe, NM,
2017https://www.flow3d.com.
[34] M. Boivineau, C. Cagran, D. Doytier, V. Eyraud, M.H. Nadal, B. Wilthan, G. Pottlacher,
Thermophysical properties of solid and liquid Ti-6Al-4V (TA6V) alloy, Int. J.
Thermophys. 27 (2006) 507–529, https://doi.org/10.1007/PL00021868.
[35] J. Liu, Q. Qin, Q. Yu, The effect of size distribution of slag particles obtained in dry
granulation on blast furnace slag cement strength, Powder Technol. 362 (2020)
32–36, https://doi.org/10.1016/j.powtec.2019.11.115.
[36] M. Tanaka, S. Tashiro, A study of thermal pinch effect of welding arcs, J. Japan Weld.
Soc. 25 (2007) 336–342, https://doi.org/10.2207/qjjws.25.336 (in Japanese).
[37] T. Kamiya, A. Kayano, Disintegration of viscous fluid in the ligament state purged
from a rotating disk, J. Chem. Eng. JAPAN. 4 (1971) 364–369, https://doi.org/10.
1252/jcej.4.364.
[38] T. Kamiya, An analysis of the ligament-type disintegration of thin liquid film at the
edge of a rotating disk, J. Chem. Eng. Japan. 5 (1972) 391–396, https://doi.org/10.
1252/jcej.5.391.
[39] J. Burns, C. Ramshaw, R. Jachuck, Measurement of liquid film thickness and the determination of spin-up radius on a rotating disc using an electrical resistance technique, Chem. Eng. Sci. 58 (2003) 2245–2253, https://doi.org/10.1016/S0009-2509
(03)00091-5.
[40] J. Rauscher, R. Kelly, J. Cole, An asymptotic solution for the laminar flow of a thin film
on a rotating disk, J. Appl. Mech. Trans. ASME 40 (1973) 43–47, https://doi.org/10.
1115/1.3422970

원문보기

Flow Field in a Sloped Channel with Damaged and Undamaged Piers: Numerical and Experimental Studies

Ehsan Oveici, Omid Tayari & Navid Jalalkamali
KSCE Journal of Civil Engineering volume 25, pages4240–4251 (2021)Cite this article

Abstract

본 논문은 경사가 완만한 수로에서 손상되거나 손상되지 않은 교각 주변의 유동 패턴을 분석했습니다. 실험은 길이가 12m이고 기울기가 0.008인 직선 수로에서 수행되었습니다. Acoustic Doppler Velocimeter(ADV)를 이용하여 3차원 유속 데이터를 수집하였고, 그 결과를 PIV(Particle Image Velocimetry) 데이터와 분석하여 비교하였습니다.

다중 블록 옵션이 있는 취수구의 퇴적물 시뮬레이션(SSIIM)은 이 연구에서 흐름의 수치 시뮬레이션을 위해 통합되었습니다. 일반적으로 비교에서 얻은 결과는 수치 데이터와 실험 데이터 간의 적절한 일치를 나타냅니다. 결과는 모든 경우에 수로 입구에서 2m 거리에서 기복적 수압 점프가 발생했음을 보여주었습니다.

경사진 수로의 최대 베드 전단응력은 2개의 손상 및 손상되지 않은 교각을 설치하기 위한 수평 수로의 12배였습니다. 이와 같은 경사수로 교각의 위치에 따라 상류측 수위는 수평수로의 유사한 조건에 비해 72.5% 감소한 반면, 이 감소량은 경사면에서 다른 경우에 비해 8.3% 감소하였다. 채널 또한 두 교각이 있는 경우 최대 Froude 수는 수평 수로의 5.7배였습니다.

This paper analyzed the flow pattern around damaged and undamaged bridge piers in a channel with a mild slope. The experiments were carried out on a straight channel with a length of 12 meters and a slope of 0.008. Acoustic Doppler velocimeter (ADV) was employed to collect three-dimensional flow velocity data, and the results were analyzed and compared with particle image velocimetry (PIV) data. Sediment Simulation in Intakes with Multiblock option (SSIIM) was incorporated for the numerical simulation of the flow in this study. Generally, the results obtained from the comparisons referred to the appropriate agreement between the numerical and the experimental data. The results showed that an undular hydraulic jump occurred at a distance of two meters from the channel entrance in every case; the maximum bed shear stress in the sloped channel was 12 times that in a horizontal channel for installing two damaged and undamaged piers. With this position of the piers in the sloped channel, the upstream water level underwent a 72.5% reduction compared to similar conditions in a horizontal channel, while the amount of this water level decrease was equal to 8.3% compared to the other cases in a sloped channel. In addition, with the presence of both piers, the maximum Froude number was 5.7 times that in a horizontal channel.

This is a preview of subscription content, access via your institution.

References

Adak TI (2018) Bathometer user guide. Adak Tajhiz Iranian, Tabriz, IranGoogle Scholar
Akbari M, Vaghefi M (2017) Experimental investigation on streamlines in a 180° sharp bend. Acta Scientiarum Technology 39:425–432, DOI: https://doi.org/10.4025/actascitechnol.v39i4.29032 Article Google Scholar
Akbari M, Vaghefi M, Chiew YM (2021) Effect of T-shaped spur dike length on mean flow characteristics along a 180-degree sharp bend. Journal of Hydrology and Hydromechanics 69(1):98–107, DOI: https://doi.org/10.2478/johh-2020-0045 Article Google Scholar
Alemi M, Maia R (2018) Numerical simulation of the flow and local scour process around single and complex bridge piers. International Journal of Civil Engineering 16:475–487, DOI: https://doi.org/10.1007/s40999-016-0137-8 Article Google Scholar
Alsaydalani MO (2020) Failure mechanism of a granular bed induced by a horizontal water jet using particle image velocimetry. KSCE Journal of Civil Engineering 24(6):1696–1705, DOI: https://doi.org/10.1007/s12205-020-0574-4 Article Google Scholar
Asadollahi M, Vaghefi M, Akbari M (2020) Effect of the position of perpendicular pier groups in a sharp bend on flow and scour patterns: Numerical simulation. Journal of the Brazilian Society of Mechanical Sciences and Engineering 42:422, DOI: https://doi.org/10.1007/s40430-020-02503-2 Article Google Scholar
Asadollahi M, Vaghefi M, Tabib Nazhad Motlagh MJ (2019) Experimental and numerical comparison of flow and scour patterns around a single and triple bridge piers located at a sharp 180 degrees bend. Scientia Iranica, DOI: https://doi.org/10.24200/sci.2019.5637.1391
Bozkus Z, Çesme M (2010) Reduction of scouring depth by using inclined piers. Canadian Journal of Civil Engineering 37:1621–1630, DOI: https://doi.org/10.1139/L10-099 Article Google Scholar
Bozkus Z, Özalp MC, Dinçer AE (2018) Effect of pier inclination angle on local scour depth around bridge pier groups. Arabian Journal for Science and Engineering 43:5413–5421, DOI: https://doi.org/10.1007/s13369-018-3141-2 Article Google Scholar
Breusers HNC, Raudkivi AJ (1991) Scouring, hydraulic structures design manual. IAHR, AA Balkema, Rotterdam, NetherlandsGoogle Scholar
Chavan R, Kumar B (2018) Prediction of scour depth and dune morphology around circular bridge piers in seepage affected alluvial channels. Environmental Fluid Mechanics 18:923–945, DOI: https://doi.org/10.1007/s10652-018-9574-z Article Google Scholar
Chiew YM, Melville BW (1986) Local scour around bridge piers. Journal of Hydraulic Research 25:15–26, DOI: https://doi.org/10.1080/00221688709499285 Article Google Scholar
Chiew YM, Melville BW (1996) Temporal development of local scour depth at bridge piers. Proceedings of North American Water and Environment Congress, ASCE, Anaheim, CA, USAGoogle Scholar
Das S, Das R, Mazumdar A (2015) Comparison of local scour characteristics around two eccentric piers of different shapes. Arabian Journal for Science and Engineering 41:1199–1213, DOI: https://doi.org/10.1007/s13369-015-1817-4 Article Google Scholar
Hurther D, Lemmin U (2001) A correction method for turbulence measurements with a 3D acoustic Doppler velocity profiler. Journal of Atmospheric and Oceanic Technology 18:446–458, DOI: https://doi.org/10.1175/1520-0426(2001)018<0446:ACMFTM>2.0.CO;2Article Google Scholar
Islam SU, Rahman H, Ying ZC, Saha SC (2016) Comparison of wake structures and force measurements behind three side-by-side cylinders. Journal of the Brazilian Society of Mechanical Sciences and Engineering 38:843–858, DOI: https://doi.org/10.1007/s40430-014-0297-x Article Google Scholar
Ismael A, Gunal M, Hussein H (2015) Effect of bridge pier position on scour reduction according to flow direction. Arabian Journal for Science and Engineering 40:1579–1590, DOI: https://doi.org/10.1007/s13369-015-1625-x Article Google Scholar
Kara S, Stoesser T, Sturm TW (2012) Turbulence statistics in compound channels with deep and shallow overbank flows. Journal of Hydraulic Research 50:482–493, DOI: https://doi.org/10.1080/00221686.2012.724194 Article Google Scholar
Karami H, Hosseinjanzadeh H, Hosseini K, Ardeshir A (2018) Scour and three-dimensional flow field measurement around short vertical-wall abutment protected by collar. KSCE Journal of Civil Engineering 22(1):141–152, DOI: https://doi.org/10.1007/s12205-017-0521-1 Article Google Scholar
Keshavarzi A, Shrestha CK, Melville B, Khabbaz H, Ranjbar-Zahedani M, Ball J (2018) Estimation of maximum scour depths at upstream of front and rear piers for two in-line circular columns. Environmental Fluid Mechanics 18:537–550, DOI: https://doi.org/10.1007/s10652-017-9572-6 Article Google Scholar
Khajeh SBM, Vaghefi M, Mahmoodi A (2017) The scour pattern around an inclined cylindrical pier in a sharp 180-degree bend: An experimental study. International Journal of River Basin Management 15:207–218, DOI: https://doi.org/10.1080/15715124.2016.1274322 Article Google Scholar
Khan MA, Sharma N (2019) Investigation of coherent flow turbulence in the proximity of mid-channel bar. KSCE Journal of Civil Engineering 23(12):5098–5108, DOI: https://doi.org/10.1007/s12205-019-1430-2 Article Google Scholar
Kumcu SY (2017) Investigation of flow over spillway modeling and comparison between experimental data and CFD analysis. KSCE Journal of Civil Engineering 21(3):994–1003, DOI: https://doi.org/10.1007/s12205-016-1257-z Article Google Scholar
Liu C, Tang X, Wei H, Wang P, Zhao H (2020) Model tests of jacked-pile penetration into sand using transparent soil and incremental particle image velocimetry. KSCE Journal of Civil Engineering 24(4):1128–1145, DOI: https://doi.org/10.1007/s12205-020-1643-4 Article Google Scholar
Nabipour M, Neyshabouri AAS, Dodaran RS, Zarrati AR, Mohajeri H, Zabetian M (2018) Experimental study of side looking ADV probe accuracy in a turbulent flow field. Journal of Mechanical Engineering 18:406–412Google Scholar
Nguyen THT, Lee J, Park SW, Ahn J (2018) Two-dimensional numerical analysis on the flow and turbulence structures in artificial dunes. KSCE Journal of Civil Engineering 22(12):4922–4929, DOI: https://doi.org/10.1007/s12205-018-0103-x Article Google Scholar
Nortek AS (2009) Vectrino velocimeter user guide. Nortek AS, Vangkroken, NorwayGoogle Scholar
Olsen NRB (1999) Computational fluid dynamics in hydraulic and sedimentation engineering. The Norwegian University of Science and Technology, Trondheim, NorwayGoogle Scholar
Olsen NRB (2001) CFD modeling for hydraulic structures. The Norwegian University of Science and Technology, Trondheim, NorwayGoogle Scholar
Olsen NRB (2003) Three-dimensional CFD modeling of self-forming meandering channel. Journal of Hydraulic Engineering 129:366–372, DOI: https://doi.org/10.1061/(ASCE)0733-9429(2003)129:5(366)Article Google Scholar
Omara H, Elsayed SM, Abdeelaal GM, Abd-Elhamid AF, Tawfik A (2018) Hydromorphological numerical model of the local scour process around bridge piers. Arabian Journal for Science and Engineering 44:4183–4199, DOI: https://doi.org/10.1007/s13369-018-3359-z Article Google Scholar
Oveici E (2020) Experimental study of large bed elements on positive surge propagation in sloping canals. PhD Thesis, Islamic Azad University, Kerman, IranGoogle Scholar
Oveici E, Tayari O, Jalalkamali, N (2020) Experimental (ADV & PIV) and numerical (CFD) comparisons of 3D flow pattern around intact and damaged bridge piers. Pertanika Journal of Science & Technology 28:523–544Google Scholar
Padova DD, Mossa M, Sibilla S (2017) SPH modelling of hydraulic jump oscillations at an abrupt drop. Water 9:790, DOI: https://doi.org/10.3390/w9100790 Article Google Scholar
Pandey M, Sharma PK, Ahmad Z, Singh UK (2018) Experimental investigation of clear-water temporal scour variation around bridge pier in gravel. Environmental Fluid Mechanics 18:871–890, DOI: https://doi.org/10.1007/s10652-017-9570-8 Article Google Scholar
Raffel M, Willert CE, Scarano F, Kähler CJ, Wereley ST, Kompenhans J (2018) Particle image velocimetry: A practical guide. Springer, Berlin, Germany
Raudkivi AJ, Ettema R (1983) Clear-water scour at cylindrical piers. Journal of Hydraulic Engineering 109:338–350, DOI: https://doi.org/10.1061/(ASCE)0733-9429(1983)109:3(338)Article Google Scholar
Schlichting H (1979) Boundary layer theory, 7th edition. McGraw Hill Education, New York, NY, USAMATH Google Scholar
Shaheed R Mohammadian A, Kheirkhah Gildeh HA (2018) A comparison of standard k-e and realizable k-e turbulence models in curved and confluent channels. Environmental Fluid Mechanics 19:543–568, DOI: https://doi.org/10.1007/s10652-018-9637-1 Article Google Scholar
Tominaga A, Nezu I (1991) Turbulent structure in compound open-channel. Journal of Hydraulic Engineering 117:21–41, DOI: https://doi.org/10.1061/(ASCE)0733-9429(1991)117:1(21)Article Google Scholar
Vaghefi M, Faraji B, Akbari M, Eghbalzadeh A (2018) Numerical investigation of flow pattern around a T-shaped spur dike in the vicinity of attractive and repelling protective structures. Journal of the Brazilian Society of Mechanical Sciences and Engineering 40:93–107, DOI: https://doi.org/10.1007/s40430-017-0954-y Article Google Scholar
Vaghefi M, Radan P, Akbari M (2019) Flow pattern around attractive, vertical, and repelling T-shaped spur dikes in a mild bend using CFD modeling. International Journal of Civil Engineering 17:607–617, DOI: https://doi.org/10.1007/s40999-018-0340-x Article Google Scholar
Vaghefi M, Safarpoor Y, Akbari M (2016) Numerical investigation of flow pattern and components of three-dimensional velocity around a submerged T-shaped spur dike in a 90 bend. Journal of Central South University 23(11):2984–2998, DOI: https://doi.org/10.1007/s11771-016-3362-z Article Google Scholar
Vaghefi M, Safarpoor Y, Akbari M (2017) Numerical comparison of the parameters influencing the turbulent flow using a T-shaped spur dike in a 90 bend. Journal of Applied Fluid Mechanics 10:231–241, DOI: https://doi.org/10.18869/acadpub.jafm.73.238.26175 Article Google Scholar
Voulgaris G, Trowbridge JH (1998) Evaluation of the acoustic Doppler velocimeter (ADV) for turbulence measurements. Journal of Atmospheric and Oceanic Technology 15:272–289, DOI: https://doi.org/10.1175/1520-0426(1998)015<0272:EOTADV>2.0.CO;2Article Google Scholar
Wang H, Tang H, Liu Q, Zhao X (2019) Topographic evolution around twin piers in a tandem arrangement. KSCE Journal of Civil Engineering 23(7):2889–2897, DOI: https://doi.org/10.1007/s12205-019-0585-1 Article Google Scholar
Xiang Q, Wei K, Li Y, Zhang M, Qin S (2020) Experimental and numerical investigation of local scour for suspended square caisson under steady flow. KSCE Journal of ivil Engineering 24(9):2682–2693, DOI: https://doi.org/10.1007/s12205-020-2343-9 Article Google Scholar
Yeow SC, Chanson H, Wang H (2016) Impact of a large cylindrical roughness on tidal bore propagation. Canadian Journal of Civil Engineering 43:724–734, DOI: https://doi.org/10.1139/cjce-2015-0557 Article Google Scholar
Zarrati AR, Nazariha M, Mashahir MB (2006) Reduction of local scour in the vicinity of bridge pier groups using collars and riprap. Journal of Hydraulic Engineering 132:154–162, DOI: https://doi.org/10.1061/(ASCE)0733-9429(2006)132:2(154)Article Google Scholar

Download references

The Study of the effect of step penetration depth on exchanges between surface and subsurface fluxes

Authors

¹ irrigation department, university of Tehran

² Dep. of Water Engineering, Faculty of Water and Soil, Gorgan University of Agricultural Sciences and Natural Resources, Golestan.

³ Assistant Professor, Department of Irrigation and Reclamation Engineering, Faculty of Agricultural Engineering and Technology, University College of Agriculture and Natural Resources, University of Tehran, P. O. Box 4111, Karaj, 31587-77871, Iran.

Abstract

The exchange of surface and subsurface flows in riverbeds, especially upstream of control structures as an important ecological area, is very important and noteworthy. The natural morphology of rivers and various in-stream structures along the flow path are important factors in the formation of such flows. Since the in-stream structures in the flow path have a more controlled and effective role than the morphology of rivers in the formation of these exchanges, in this study the effect of the penetration depth of these structures in the porous bed on the characteristics of exchange flows through experiments and Numerical simulation has been investigated. The experiments were performed in a flume with a length of 10 m, width of 20 cm, depth of 30 cm and a slope of 0.01, for three different penetration depths. Potassium permanganate detector was used for tracking the flow. In addition, to obtain exchange flow characteristics; the mainstream and the exchange pattern were simulated by particle tracking method using Flow 3D software. The results showed that in the Reynolds range 1020 to 3450, with increasing the penetration depth of the structure from 0.09 to 0.13 m, the retention time of the exchange flow increases up to 6.6%. In addition, the length of the effect of the structure up to 9%, the length of the exchange path up to 4.6% and the penetration depth of the exchange increases up to 7.7% while the exchange rate decreases to 22%. Therefore, in order to increase the exchange rate, it is recommended to use a structure with a lower penetration depth and to increase the retention time, a structure with a greater penetration depth is recommended.

중요한 생태 지역으로서 특히 제어 구조물의 상류 하천 바닥에서 지표 및 지하 흐름의 교환은 매우 중요하고 주목할 만합니다. 하천의 자연적 형태와 유동 경로를 따라 흐르는 다양한 하천 구조는 이러한 유동 형성에 중요한 요소입니다.

흐름 경로의 유류 구조는 이러한 교환의 형성에서 강의 형태보다 더 제어되고 효과적인 역할을 하기 때문에 본 연구에서는 다공성 층에서 이러한 구조의 침투 깊이가 교환의 특성에 미치는 영향 실험과 수치 시뮬레이션을 통한 흐름이 조사되었습니다.

실험은 길이 10m, 너비 20cm, 깊이 30cm, 기울기 0.01의 수로에서 세 가지 다른 침투 깊이에 대해 수행되었습니다. 흐름을 추적하기 위해 과망간산 칼륨 검출기가 사용되었습니다. 또한, 교환 흐름 특성을 얻기 위해; Flow 3D 소프트웨어를 사용하여 입자 추적 방법으로 주류 및 교환 패턴을 시뮬레이션했습니다.

결과는 Reynolds 범위 1020 ~ 3450에서 구조물의 침투 깊이가 0.09에서 0.13m로 증가함에 따라 교환 흐름의 체류 시간이 최대 6.6%까지 증가함을 보여주었습니다. 또한 구조의 효과 길이는 최대 9%, 교환 경로의 길이는 최대 4.6%, 교환의 침투 깊이는 최대 7.7%까지 증가하는 반면 환율은 22%로 감소합니다.

따라서 환율을 높이기 위해서는 침투깊이가 낮은 구조를 사용하는 것이 좋으며, 머무름 시간을 늘리기 위해서는 침투깊이가 큰 구조를 사용하는 것이 좋습니다.

Keywords

원문보기

Fig. 1. Model geometry with the computational domain, extrusion nozzle, toolpath, and boundary conditions. The model is presented while printing the fifth layer.

재료 압출 적층 제조에서 증착된 층의 안정성 및 변형

Md Tusher Mollah Raphaël 사령관 Marcin P. Serdeczny David B. Pedersen Jon Spangenberg덴마크 공과 대학 기계 공학과, Kgs. 덴마크 링비

2020년 12월 22일 접수, 2021년 5월 1일 수정, 2021년 7월 15일 수락, 2021년 7월 21일 온라인 사용 가능, 기록 버전 2021년 8월 17일 .

Abstract

이 문서는 재료 압출 적층 제조 에서 여러 레이어를 인쇄하는 동안 증착 흐름의 전산 유체 역학 시뮬레이션 을 제공합니다 . 개발된 모델은 증착된 레이어의 형태를 예측하고 점소성 재료 를 인쇄하는 동안 레이어 변형을 캡처합니다 . 물리학은 일반화된 뉴턴 유체 로 공식화된 Bingham 구성 모델의 연속성 및 운동량 방정식에 의해 제어됩니다. . 증착된 층의 단면 모양이 예측되고 재료의 다양한 구성 매개변수에 대해 층의 변형이 연구됩니다. 층의 변형은 인쇄물의 정수압과 압출시 압출압력으로 인한 것임을 알 수 있다. 시뮬레이션에 따르면 항복 응력이 높을수록 변형이 적은 인쇄물이 생성되는 반면 플라스틱 점도 가 높을수록 증착된 레이어에서변형이 커 집니다 . 또한, 인쇄 속도, 압출 속도 의 영향, 층 높이 및 인쇄된 층의 변형에 대한 노즐 직경을 조사합니다. 마지막으로, 이 모델은 후속 인쇄된 레이어의 정수압 및 압출 압력을 지원하기 위해 증착 후 점소성 재료가 요구하는 항복 응력의 필요한 증가에 대한 보수적인 추정치를 제공합니다.

This paper presents computational fluid dynamics simulations of the deposition flow during printing of multiple layers in material extrusion additive manufacturing. The developed model predicts the morphology of the deposited layers and captures the layer deformations during the printing of viscoplastic materials. The physics is governed by the continuity and momentum equations with the Bingham constitutive model, formulated as a generalized Newtonian fluid. The cross-sectional shapes of the deposited layers are predicted, and the deformation of layers is studied for different constitutive parameters of the material. It is shown that the deformation of layers is due to the hydrostatic pressure of the printed material, as well as the extrusion pressure during the extrusion. The simulations show that a higher yield stress results in prints with less deformations, while a higher plastic viscosity leads to larger deformations in the deposited layers. Moreover, the influence of the printing speed, extrusion speed, layer height, and nozzle diameter on the deformation of the printed layers is investigated. Finally, the model provides a conservative estimate of the required increase in yield stress that a viscoplastic material demands after deposition in order to support the hydrostatic and extrusion pressure of the subsequently printed layers.

키워드

점성 플라스틱 재료, 재료 압출 적층 제조(MEX-AM), 다층 증착, 전산유체역학(CFD), 변형 제어
Viscoplastic Materials, Material Extrusion Additive Manufacturing (MEX-AM), Multiple-Layers Deposition, Computational Fluid Dynamics (CFD), Deformation Control

Introduction

Three-dimensional printing of viscoplastic materials has grown in popularity over the recent years, due to the success of Material Extrusion Additive Manufacturing (MEX-AM) [1]. Viscoplastic materials, such as ceramic pastes [2,3], hydrogels [4], thermosets [5], and concrete [6], behave like solids when the applied load is below their yield stress, and like a fluid when the applied load exceeds their yield stress [7]. Viscoplastic materials are typically used in MEX-AM techniques such as Robocasting [8], and 3D concrete printing [9,10]. The differences between these technologies lie in the processing of the material before the extrusion and in the printing scale (from microscale to big area additive manufacturing). In these extrusion-based technologies, the structure is fabricated in a layer-by-layer approach onto a solid surface/support [11, 12]. During the process, the material is typically deposited on top of the previously printed layers that may be already solidified (wet-on-dry printing) or still deformable (wet-on-wet printing) [1]. In wet-on-wet printing, control over the deformation of layers is important for the stability and geometrical accuracy of the prints. If the material is too liquid after the deposition, it cannot support the pressure of the subsequently deposited layers. On the other hand, the material flowability is a necessity during extrusion through the nozzle. Several experimental studies have been performed to analyze the physics of the extrusion and deposition of viscoplastic materials, as reviewed in Refs. [13–16]. The experimental measurements can be supplemented with Computational Fluid Dynamics (CFD) simulations to gain a more complete picture of MEX-AM. A review of the CFD studies within the material processing and deposition in 3D concrete printing was presented by Roussel et al. [17]. Wolfs et al. [18] predicted numerically the failure-deformation of a cylindrical structure due to the self-weight by calculating the stiffness and strength of the individual layers. It was found that the deformations can take place in all layers, however the most critical deformation occurs in the bottom layer. Comminal et al. [19,20] presented three-dimensional simulations of the material deposition in MEX-AM, where the fluid was approximated as Newtonian. Subsequently, the model was experimentally validated in Ref. [21] for polymer-based MEX-AM, and extended to simulate the deposition of multiple layers in Ref. [22], where the previously printed material was assumed solid. Xia et al. [23] simulated the influence of the viscoelastic effects on the shape of deposited layers in MEX-AM. A numerical model for simulating the deposition of a viscoplastic material was recently presented and experimentally validated in Refs. [24] and [25]. These studies focused on predicting the cross-sectional shape of a single printed layer for different processing conditions (relative printing speed, and layer height). Despite these research efforts, a limited number of studies have focused on investigating the material deformations in wet-on-wet printing when multiple layers are deposited on top of each other. This paper presents CFD simulations of the extrusion-deposition flow of a viscoplastic material for several subsequent layers (viz. three- and five-layers). The material is continuously printed one layer over another on a fixed solid surface. The rheology of the viscoplastic material is approximated by the Bingham constitutive equation that is formulated using the Generalized Newtonian Fluid (GNF) model. The CFD model is used to predict the cross-sectional shapes of the layers and their deformations while printing the next layers on top. Moreover, the simulations are used to quantify the extrusion pressure applied by the deposited material on the substrate, and the previously printed layers. Numerically, it is investigated how the process parameters (i.e., the extrusion speed, printing speed, nozzle diameter, and layer height) and the material rheology affect the deformations of the deposited layers. Section 2 describes the methodology of the study. Section 3 presents and discusses the results. The study is summarized and concluded in Section 4.

References

[1] R.A. Buswell, W.R. Leal De Silva, S.Z. Jones, J. Dirrenberger, 3D printing using
concrete extrusion: a roadmap for research, Cem. Concr. Res. 112 (2018) 37–49.
[2] Z. Chen, Z. Li, J. Li, C. Liu, C. Lao, Y. Fu, C. Liu, Y. Li, P. Wang, Y. He, 3D printing of
ceramics: a review, J. Eur. Ceram. Soc. 39 (4) (2019) 661–687.
[3] A. Bellini, L. Shor, S.I. Guceri, New developments in fused deposition modeling of
ceramics, Rapid Prototyp. J. 11 (4) (2005) 214–220.
[4] S. Aktas, D.M. Kalyon, B.M. Marín-Santib´
anez, ˜ J. P´erez-Gonzalez, ´ Shear viscosity
and wall slip behavior of a viscoplastic hydrogel, J. Rheol. 58 (2) (2014) 513–535.
[5] J. Lindahl, A. Hassen, S. Romberg, B. Hedger, P. Hedger Jr., M. Walch, T. Deluca,
W. Morrison, P. Kim, A. Roschli, D. Nuttall, Large-scale Additive Manufacturing
with Reactive Polymers, Oak Ridge National Lab.(ORNL), Oak Ridge, TN (United
States), 2018.
[6] V.N. Nerella, V. Mechtcherine, Studying the printability of fresh concrete for
formwork-free Concrete onsite 3D Printing Technology (CONPrint3D), 3D Concr.
Print. Technol. (2019) 333–347.
[7] C. Tiu, J. Guo, P.H.T. Uhlherr, Yielding behaviour of viscoplastic materials, J. Ind.
Eng. Chem. 12 (5) (2006) 653–662.
[8] B. Dietemann, F. Bosna, M. Lorenz, N. Travitzky, H. Kruggel-Emden, T. Kraft,
C. Bierwisch, Modeling robocasting with smoothed particle hydrodynamics:
printing gapspanning filaments, Addit. Manuf. 36 (2020), 101488.
[9] B. Khoshnevis, R. Russell, H. Kwon, S. Bukkapatnam, Contour crafting – a layered
fabrication, Spec. Issue IEEE Robot. Autom. Mag. 8 (3) (2001) 33–42.
[10] D. Asprone, F. Auricchio, C. Menna, V. Mercuri, 3D printing of reinforced concrete
elements: technology and design approach, Constr. Build. Mater. 165 (2018)
218–231.
[11] J. Jiang, Y. Ma, Path planning strategies to optimize accuracy, quality, build time
and material use in additive manufacturing: a review, Micromachines 11 (7)
(2020) 633.
[12] J. Jiang, A novel fabrication strategy for additive manufacturing processes,
J. Clean. Prod. 272 (2020), 122916.
[13] F. Bos, R. Wolfs, Z. Ahmed, T. Salet, Additive manufacturing of concrete in
construction: potentials and challenges, Virtual Phys. Prototyp. 11 (3) (2016)
209–225.
[14] P. Wu, J. Wang, X. Wang, A critical review of the use of 3-D printing in the
construction industry, Autom. Constr. 68 (2016) 21–31.
[15] T.D. Ngo, A. Kashani, G. Imbalzano, K.T. Nguyen, D. Hui, Additive manufacturing
(3D printing): a review of materials, methods, applications and challenges,
Compos. Part B: Eng. 143 (2018) 172–196.
[16] M. Valente, A. Sibai, M. Sambucci, Extrusion-based additive manufacturing of
concrete products: revolutionizing and remodeling the construction industry,
J. Compos. Sci. 3 (3) (2019) 88.
[17] N. Roussel, J. Spangenberg, J. Wallevik, R. Wolfs, Numerical simulations of
concrete processing: from standard formative casting to additive manufacturing,
Cem. Concr. Res. 135 (2020), 106075.
[18] R.J.M. Wolfs, F.P. Bos, T.A.M. Salet, Early age mechanical behaviour of 3D printed
concrete: numerical modelling and experimental testing, Cem. Concr. Res. 106
(2018) 103–116.
[19] R. Comminal, M.P. Serdeczny, D.B. Pedersen, J. Spangenberg, Numerical modeling
of the strand deposition flow in extrusion-based additive manufacturing, Addit.
Manuf. 20 (2018) 68–76.
[20] R. Comminal, M.P. Serdeczny, D.B. Pedersen, J. Spangenberg, Numerical modeling
of the material deposition and contouring precision in fused deposition modeling,
in Proceedings of the 29th Annual International Solid Freeform Fabrication
Symposium, Austin, TX, USA, 2018, pp. 1855–1864.
[21] M.P. Serdeczny, R. Comminal, D.B. Pedersen, J. Spangenberg, Experimental
validation of a numerical model for the strand shape in material extrusion additive
manufacturing, Addit. Manuf. 24 (2018) 145–153.
[22] M.P. Serdeczny, R. Comminal, D.B. Pedersen, J. Spangenberg, Numerical
simulations of the mesostructure formation in material extrusion additive
manufacturing, Addit. Manuf. 28 (2019) 419–429.
[23] H. Xia, J. Lu, G. Tryggvason, A numerical study of the effect of viscoelastic stresses
in fused filament fabrication, Comput. Methods Appl. Mech. Eng. 346 (2019)
242–259.
[24] R. Comminal, W.R.L. da Silva, T.J. Andersen, H. Stang, J. Spangenberg, Influence
of processing parameters on the layer geometry in 3D concrete printing:
experiments and modelling, in: Proceedings of the Second RILEM International
Conference on Concrete and Digital Fabrication, vol. 28, 2020, pp. 852–862.
[25] R. Comminal, W.R.L. da Silva, T.J. Andersen, H. Stang, J. Spangenberg, Modelling
of 3D concrete printing based on computational fluid dynamics, Cem. Concr. Res.
38 (2020), 106256.
[26] E.C. Bingham, An investigation of the laws of plastic flow, US Bur. Stand. Bull. 13
(1916) 309–352.
[27] N. Casson, A flow equation for pigment-oil suspensions of the printing ink type,
Rheol. Disperse Syst. (1959) 84–104.
[28] W.H. Herschel, R. Bulkley, Konsistenzmessungen von Gummi-Benzollosungen, ¨
Kolloid Z. 39 (1926) 291–300.
[29] “FLOW-3D | We solve The World’s Toughest CFD Problems,” FLOW SCIENCE.
〈https://www.flow3d.com/〉. (Accessed 27 June 2020).
[30] S. Jacobsen, R. Cepuritis, Y. Peng, M.R. Geiker, J. Spangenberg, Visualizing and
simulating flow conditions in concrete form filling using pigments, Constr. Build.
Mater. 49 (2013) 328–342.
[31] E.J. O’Donovan, R.I. Tanner, Numerical study of the Bingham squeeze film
problem, J. Non-Newton. Fluid Mech. 15 (1) (1984) 75–83.
[32] C.W. Hirt, B.D. Nichols, Volume of fluid (VOF) method for the dynamics of free
boundaries, J. Comput. Phys. 39 (1) (1981) 201–225.
[33] R. Comminal, J. Spangenberg, J.H. Hattel, Cellwise conservative unsplit advection
for the volume of fluid method, J. Comput. Phys. 283 (2015) 582–608.
[34] A. Negar, S. Nazarian, N.A. Meisel, J.P. Duarte, Experimental prediction of material
deformation in large-scale additive manufacturing of concrete, Addit. Manuf. 37
(2021), 101656.

원문 보기

Gating System Design Based on Numerical Simulation and Production Experiment Verification of Aluminum Alloy Bracket Fabricated by Semi-solid Rheo-Die Casting Process

반고체 레오 다이 캐스팅 공정으로 제작된 알루미늄 합금 브래킷의 수치 시뮬레이션 및 생산 실험 검증을 기반으로 한 게이팅 시스템 설계

International Journal of Metalcasting volume 16, pages878–893 (2022)Cite this article

Abstract

In this study a gating system including sprue, runner and overflows for semi-solid rheocasting of aluminum alloy was designed by means of numerical simulations with a commercial software. The effects of pouring temperature, mold temperature and injection speed on the filling process performance of semi-solid die casting were studied. Based on orthogonal test analysis, the optimal die casting process parameters were selected, which were metal pouring temperature 590 °C, mold temperature 260 °C and injection velocity 0.5 m/s. Semi-solid slurry preparation process of Swirled Enthalpy Equilibration Device (SEED) was used for die casting production experiment. Aluminum alloy semi-solid bracket components were successfully produced with the key die casting process parameters selected, which was consistent with the simulation result. The design of semi-solid gating system was further verified by observing and analyzing the microstructure of different zones of the casting. The characteristic parameters, particle size and shape factor of microstructure of the produced semi-solid casting showed that the semi-solid aluminum alloy components are of good quality.

이 연구에서 알루미늄 합금의 반고체 레오캐스팅을 위한 스프루, 러너 및 오버플로를 포함하는 게이팅 시스템은 상용 소프트웨어를 사용한 수치 시뮬레이션을 통해 설계되었습니다. 주입 온도, 금형 온도 및 사출 속도가 반고체 다이캐스팅의 충전 공정 성능에 미치는 영향을 연구했습니다. 직교 테스트 분석을 기반으로 금속 주입 온도 590°C, 금형 온도 260°C 및 사출 속도 0.5m/s인 최적의 다이 캐스팅 공정 매개변수가 선택되었습니다. Swirled Enthalpy Equilibration Device(SEED)의 반고체 슬러리 제조 공정을 다이캐스팅 생산 실험에 사용하였다. 알루미늄 합금 반고체 브래킷 구성 요소는 시뮬레이션 결과와 일치하는 주요 다이 캐스팅 공정 매개변수를 선택하여 성공적으로 생산되었습니다. 반고체 게이팅 시스템의 설계는 주조의 다른 영역의 미세 구조를 관찰하고 분석하여 추가로 검증되었습니다. 생산된 반고체 주조물의 특성 매개변수, 입자 크기 및 미세 구조의 형상 계수는 반고체 알루미늄 합금 부품의 품질이 양호함을 보여주었습니다.

References

G. Li, H. Lu, X. Hu et al., Current progress in rheoforming of wrought aluminum alloys: a review. Met. Open Access Metall. J. 10(2), 238 (2020)CAS Google Scholar
G. Eisaabadi, A. Nouri, Effect of Sr on the microstructure of electromagnetically stirred semi-solid hypoeutectic Al–Si alloys. Int. J. Metalcast. 12, 292–297 (2018). https://doi.org/10.1007/s40962-017-0161-8 CAS Article Google Scholar
C. Xghab, D. Qza, E. Spma et al., Blistering in semi-solid die casting of aluminium alloys and its avoidance. Acta Mater. 124, 446–455 (2017)Article Google Scholar
M. Modigell, J. Koke, Rheological modelling on semi-solid metal alloys and simulation of thixocasting processes. J. Mater. Process. Technol. 111(1–3), 53–58 (2001)CAS Article Google Scholar
A. Pola, M. Tocci, P. Kapranos, Microstructure and properties of semi-solid aluminum alloys: a literature review. Met. Open Access Metall. J. 8(3), 181 (2018)Google Scholar
M.C. Flemings, Behavior of metal alloys in the semisolid state. Metall. Trans. B 22, 269–293 (1991). https://doi.org/10.1007/BF02651227 Article Google Scholar
Q. Zhu, Semi-solid moulding: competition to cast and machine from forging in making automotive complex components. Trans. Nonferrous Met. Soc. China 20, 1042–1047 (2010)Article Google Scholar
K. Prapasajchavet, Y. Harada, S. Kumai, Microstructure analysis of Al–5.5 at.%Mg alloy semi-solid slurry by Weck’s reagent. Int. J. Metalcast. 11(1), 123 (2017). https://doi.org/10.1007/s40962-016-0084-9 Article Google Scholar
P. Das, S.K. Samanta, S. Tiwari, P. Dutta, Die filling behaviour of semi solid A356 Al alloy slurry during rheo pressure die casting. Trans. Indian Inst. Met. 68(6), 1215–1220 (2015). https://doi.org/10.1007/s12666-015-0706-6 CAS Article Google Scholar
B. Zhou, S. Lu, K. Xu et al., Microstructure and simulation of semisolid aluminum alloy castings in the process of stirring integrated transfer-heat (SIT) with water cooling. Int. J. Metalcast. 14(2), 396–408 (2019). https://doi.org/10.1007/s40962-019-00357-6 CAS Article Google Scholar
S. Ji, Z. Fan, Solidification behavior of Sn–15 wt Pct Pb alloy under a high shear rate and high intensity of turbulence during semisolid processing. Metall. Mater. Trans. A. 33(11), 3511–3520 (2002). https://doi.org/10.1007/s11661-002-0338-4 Article Google Scholar
P. Kapranos, P.J. Ward, H.V. Atkinson, D.H. Kirkwood, Near net shaping by semi-solid metal processing. Mater. Des. 21, 387–394 (2000). https://doi.org/10.1016/S0261-3069(99)00077-1 Article Google Scholar
H.V. Atkinson, Alloys for semi-solid processing. Solid State Phenom. 192–193, 16–27 (2013)Google Scholar
L. Rogal, Critical assessment: opportunities in developing semi-solid processing: aluminium, magnesium, and high-temperature alloys. Mater. Sci. Technol. Mst A Publ. Inst. Met. 33, 759–764 (2017)CAS Article Google Scholar
H. Guo, Rheo-diecasting process for semi-solid aluminum alloys. J. Wuhan Univ. Technol. Mater. Sci. Ed. 22(004), 590–595 (2007)CAS Article Google Scholar
T. Chucheep, J. Wannasin, R. Canyook, T. Rattanochaikul, S. Janudom, S. Wisutmethangoon, M.C. Flemings, Characterization of flow behavior of semi-solid slurries with low solid fractions. Metall. Mater. Trans. A 44(10), 4754–4763 (2013)CAS Article Google Scholar
M. Li, Y.D. Li, W.L. Yang et al., Effects of forming processes on microstructures and mechanical properties of A356 aluminum alloy prepared by self-inoculation method. Mater. Res. 22(3) (2019)
P. Côté, M.E. Larouche, X.G. Chen et al., New developments with the SEED technology. Solid State Phenom. 192(3), 373–378 (2012)Article Google Scholar
I. Dumanić, S. Jozić, D. Bajić et al., Optimization of semi-solid high-pressure die casting process by computer simulation, Taguchi method and grey relational analysis. Inter Metalcast. 15, 108–118 (2021). https://doi.org/10.1007/s40962-020-00422-5 Article Google Scholar
Y. Bai et al., Numerical simulation on the rheo-diecasting of the semi-solid A356 aluminum alloy. Int. J. Miner. Metall. Mater. 16, 422 (2009). https://doi.org/10.1016/S1674-4799(09)60074-1 CAS Article Google Scholar
B.C. Bhunia, Studies on die filling of A356 Al alloy and development of a steering knuckle component using rheo pressure die casting system. J. Mater. Process. Technol. 271, 293–311 (2019). https://doi.org/10.1016/j.jmatprotec.2019.04.014 CAS Article Google Scholar
A. Guo, J. Zhao, C. Xu et al., Effects of pouring temperature and electromagnetic stirring on porosity and mechanical properties of A357 aluminum alloy rheo-diecasting. J. Mater. Eng. Perform. (2018). https://doi.org/10.1007/s11665-018-3310-1 Article Google Scholar
C.G. Kang, S.M. Lee, B.M. Kim, A study of die design of semi-solid die casting according to gate shape and solid fraction. J. Mater. Process. Technol. 204(1–3), 8–21 (2008)CAS Article Google Scholar
Z. Liu, W. Mao, T. Wan et al., Study on semi-solid A380 aluminum alloy slurry prepared by water-cooling serpentine channel and its rheo-diecasting. Met. Mater. Int. (2020). https://doi.org/10.1007/s12540-020-00672-2 Article Google Scholar
Z.Y. Liu, W.M. Mao, W.P. Wang et al., Investigation of rheo-diecasting mold filling of semi-solid A380 aluminum alloy slurry. Int. J. Miner. Metall. Mater. 24(006), 691–700 (2017)CAS Article Google Scholar
M. Arif, M.Z. Omar, N. Muhamad et al., Microstructural evolution of solid-solution-treated Zn–22Al in the semisolid state. J. Mater. Sci. Technol. 29(008), 765–774 (2013)CAS Article Google Scholar

Keywords

semi-solid rheo-die casting
gating system
process parameters
numerical simulation
microstructure

원문보기

Figure 2. Schematic diagram for pilot-scale cooling-water circulation system (a) along with a real picture of the system (b).

Application of Computational Fluid Dynamics in Chlorine-Dynamics Modeling of In-Situ Chlorination Systems for Cooling Systems

Jongchan Yi 1, Jonghun Lee 1, Mohd Amiruddin Fikri 2,3, Byoung-In Sang 4 and Hyunook Kim 1,*

Abstract

염소화는 상대적인 효율성과 저렴한 비용으로 인해 발전소 냉각 시스템에서 생물학적 오염을 제어하는데 선호되는 방법입니다. 해안 지역에 발전소가 있는 경우 바닷물을 사용하여 현장에서 염소를 전기화학적으로 생성할 수 있습니다. 이를 현장 전기염소화라고 합니다. 이 접근 방식은 유해한 염소화 부산물이 적고 염소를 저장할 필요가 없다는 점을 포함하여 몇 가지 장점이 있습니다. 그럼에도 불구하고, 이 전기화학적 공정은 실제로는 아직 초기 단계에 있습니다. 이 연구에서는 파일럿 규모 냉각 시스템에서 염소 붕괴를 시뮬레이션하기 위해 병렬 1차 동역학을 적용했습니다. 붕괴가 취수관을 따라 발생하기 때문에 동역학은 전산유체역학(CFD) 코드에 통합되었으며, 이후에 파이프의 염소 거동을 시뮬레이션하는데 적용되었습니다. 실험과 시뮬레이션 데이터는 강한 난류가 형성되는 조건하에서도 파이프 벽을 따라 염소 농도가 점진적인 것으로 나타났습니다. 염소가 중간보다 파이프 표면을 따라 훨씬 더 집중적으로 남아 있다는 사실은 전기 염소화를 기반으로 하는 시스템의 전체 염소 요구량을 감소시킬 수 있었습니다. 현장 전기 염소화 방식의 냉각 시스템은 직접 주입 방식에 필요한 염소 사용량의 1/3만 소비했습니다. 따라서 현장 전기염소화는 해안 지역의 발전소에서 바이오파울링 제어를 위한 비용 효율적이고 환경 친화적인 접근 방식으로 사용될 수 있다고 결론지었습니다.

Chlorination is the preferred method to control biofouling in a power plant cooling system due to its comparative effectiveness and low cost. If a power plant is located in a coastal area, chlorine can be electrochemically generated in-situ using seawater, which is called in-situ electrochlorination; this approach has several advantages including fewer harmful chlorination byproducts and no need for chlorine storage. Nonetheless, this electrochemical process is still in its infancy in practice. In this study, a parallel first-order kinetics was applied to simulate chlorine decay in a pilot-scale cooling system. Since the decay occurs along the water-intake pipe, the kinetics was incorporated into computational fluid dynamics (CFD) codes, which were subsequently applied to simulate chlorine behavior in the pipe. The experiment and the simulation data indicated that chlorine concentrations along the pipe wall were incremental, even under the condition where a strong turbulent flow was formed. The fact that chlorine remained much more concentrated along the pipe surface than in the middle allowed for the reduction of the overall chlorine demand of the system based on the electro-chlorination. The cooling system, with an in-situ electro-chlorination, consumed only 1/3 of the chlorine dose demanded by the direct injection method. Therefore, it was concluded that in-situ electro-chlorination could serve as a cost-effective and environmentally friendly approach for biofouling control at power plants on coastal areas.

Keywords

computational fluid dynamics; power plant; cooling system; electro-chlorination; insitu chlorination

Figure 1. Electrodes and batch experiment set-up. (a) Two cylindrical electrodes used in this study. (b) Batch experiment set-up for kinetic tests.

Figure 3. Free chlorine decay curves in seawater with different TOC and initial chlorine concentration. Each line represents the predicted concentration of chlorine under a given condition. (a) Artificial seawater solution with 1 mg L−1 of TOC; (b) artificial seawater solution with 2 mg L−1 of TOC; (c) artificial seawater solution with 3 mg L−1 of TOC; (d) West Sea water (1.3 mg L−1 of TOC).

Figure 4. Correlation between model and experimental data in the chlorine kinetics using seawater.

Figure 5. Free chlorine concentrations in West Sea water under different current conditions in an insitu electro-chlorination system.

Figure 6. Free chlorine distribution along the sampling ports under different flow rates. Each dot represents experimental data, and each point on the black line is the expected chlorine concentration obtained from computational fluid dynamics (CFD) simulation with a parallel first-order decay model. The red-dotted line is the desirable concentration at the given flow rate: (a) 600 L min−1 of flow rate, (b) 700 L min−1 of flow rate, (c) 800 L min−1 of flow rate, (d) 900 L min−1 of flow rate.

Figure 7. Fluid contour images from CFD simulation of the electro-chlorination experiment. Inlet flow rate is 800 L min−1. Outlet pressure was set to 10.8 kPa. (a) Chlorine concentration; (b) expanded view of electrode side in image (a); (c) velocity magnitude; (d) pressure.

Figure 8. Chlorine concentration contour in the simulation of full-scale in-situ electro-chlorination with different cathode positions. The pipe diameter is 2 m and the flow rate is 14 m3 s−1. The figure shows 10 m of the pipeline. (a) The simulation result when the cathode is placed on the surface of the pipe wall. (b) The simulation result when the cathode is placed on the inside of the pipe with 100 mm of distance from the pipe wall.

Figure 9. Comparison of in-situ electro-chlorination and direct chlorine injection in full-scale applications. (a) Estimated chlorine concentrations along the pipe surface. (b) Relative chlorine demands.

References

Macknick, J.; Newmark, R.; Heath, G.; Hallett, K.C. Operational water consumption and withdrawal factors for electricity generating technologies: A review of existing literature. Environ. Res. Lett. 2012, 7, 045802.
Pan, S.-Y.; Snyder, S.W.; Packman, A.I.; Lin, Y.J.; Chiang, P.-C. Cooling water use in thermoelectric power generation and its associated challenges for addressing water-energy nexus. Water-Energy Nexus 2018, 1, 26–41.
Feeley, T.J., III; Skone, T.J.; Stiegel, G.J., Jr.; McNemar, A.; Nemeth, M.; Schimmoller, B.; Murphy, J.T.;
Manfredo, L. Water: A critical resource in the thermoelectric power industry. Energy 2008, 33, 1–11.
World Nuclear Association. World Nuclear Performance Report 2016; World Nuclear Association: London, UK, 2016.
Pugh, S.; Hewitt, G.; Müller-Steinhagen, H. Fouling during the use of seawater as coolant—The development of a user guide. Heat Transf. Eng. 2005, 26, 35–43.
Satpathy, K.K.; Mohanty, A.K.; Sahu, G.; Biswas, S.; Prasad, M.; Slvanayagam, M. Biofouling and its control in seawater cooled power plant cooling water system—A review. Nucl. Power 2010, 17, 191–242.
Cristiani, P.; Perboni, G. Antifouling strategies and corrosion control in cooling circuits. Bioelectrochemistry 2014, 97, 120–126.
Walker, M.E.; Safari, I.; Theregowda, R.B.; Hsieh, M.-K.; Abbasian, J.; Arastoopour, H.; Dzombak, D.A.; Miller, D.C. Economic impact of condenser fouling in existing thermoelectric power plants. Energy 2012,44, 429–437.
Yi, J.; Ahn, Y.; Hong, M.; Kim, G.-H.; Shabnam, N.; Jeon, B.; Sang, B.-I.; Kim, H. Comparison between OCl−-Injection and In Situ Electrochlorination in the Formation of Chlorate and Perchlorate in Seawater. Appl.Sci. 2019, 9, 229.
Xue, Y.; Zhao, J.; Qiu, R.; Zheng, J.; Lin, C.; Ma, B.; Wang, P. In Situ glass antifouling using Pt nanoparticle coating for periodic electrolysis of seawater. Appl. Surf. Sci. 2015, 357, 60–68.
Mahfouz, A.B.; Atilhan, S.; Batchelor, B.; Linke, P.; Abdel-Wahab, A.; El-Halwagi, M.M. Optimal scheduling of biocide dosing for seawater-cooled power and desalination plants. Clean Technol. Environ. Policy 2011, 13, 783–796.
Rubio, D.; López-Galindo, C.; Casanueva, J.F.; Nebot, E. Monitoring and assessment of an industrial antifouling treatment. Seasonal effects and influence of water velocity in an open once-through seawater cooling system. Appl. Therm. Eng. 2014, 67, 378–387.
European Integrated Pollution Prevention and Control (IPPC) Bureau, European Commission. Reference Document on the Application of Best Available Techniques to Industrial Cooling Systems December 2001; European Commission, Tech. Rep: Brussels, Belgium, 2001.
Venkatesan R.; Murthy P. S. Macrofouling Control in Power Plants. In Springer Series on Biofilms; Springer: Berlin/Heidelberg, Germany, 2008.
Kastl, G.; Fisher, I.; Jegatheesan, V. Evaluation of chlorine decay kinetics expressions for drinking water distribution systems modelling. J. Water Supply Res. Technol. AQUA 1999, 48, 219–226.
Fisher, I.; Kastl, G.; Sathasivan, A.; Cook, D.; Seneverathne, L. General model of chlorine decay in blends of surface waters, desalinated water, and groundwaters. J. Environ. Eng. 2015, 141, 04015039.
Fisher, I.; Kastl, G.; Sathasivan, A.; Jegatheesan, V. Suitability of chlorine bulk decay models for planning and management of water distribution systems. Crit. Rev. Environ. Sci. Technol. 2011, 41, 1843–1882.
Fisher, I.; Kastl, G.; Sathasivan, A. Evaluation of suitable chlorine bulk-decay models for water distribution systems. Water Res. 2011, 45, 4896–4908.
Haas, C.N.; Karra, S. Kinetics of wastewater chlorine demand exertion. J. (Water Pollut. Control Fed.) 1984, 56, 170–173.
Zeng, J.; Jiang, Z.; Chen, Q.; Zheng, P.; Huang, Y. The decay kinetics of residual chlorine in cooling seawater simulation experiments. Acta Oceanol. Sin. 2009, 28, 54–59.
Saeed, S.; Prakash, S.; Deb, N.; Campbell, R.; Kolluru, V.; Febbo, E.; Dupont, J. Development of a sitespecific kinetic model for chlorine decay and the formation of chlorination by-products in seawater. J. Mar. Sci. Eng. 2015, 3, 772–792.
Al Heboos, S.; Licskó, I. Application and comparison of two chlorine decay models for predicting bulk chlorine residuals. Period. Polytech. Civ. Eng. 2017, 61, 7–13.
Shadloo, M.S.; Oger, G.; Le Touzé, D. Smoothed particle hydrodynamics method for fluid flows, towards industrial applications: Motivations, current state, and challenges. Comput. Fluids 2016, 136, 11–34.
Wols, B.; Hofman, J.; Uijttewaal, W.; Rietveld, L.; Van Dijk, J. Evaluation of different disinfection calculation methods using CFD. Environ. Model. Softw. 2010, 25, 573–582.
Angeloudis, A.; Stoesser, T.; Falconer, R.A. Predicting the disinfection efficiency range in chlorine contact tanks through a CFD-based approach. Water Res. 2014, 60, 118–129.
Zhang, J.; Tejada-Martínez, A.E.; Zhang, Q. Developments in computational fluid dynamics-based modeling for disinfection technologies over the last two decades: A review. Environ. Model. Softw. 2014, 58,71–85.
Lim, Y.H.; Deering, D.D. In Modeling Chlorine Residual in a Ground Water Supply Tank for a Small Community in Cold Conditions, World Environmental and Water Resources Congress 2017; American Society of Civil Engineers: Reston, Virginia, USA, 2017; pp. 124–138.
Hernández-Cervantes, D.; Delgado-Galván, X.; Nava, J.L.; López-Jiménez, P.A.; Rosales, M.; Mora Rodríguez, J. Validation of a computational fluid dynamics model for a novel residence time distribution analysis in mixing at cross-junctions. Water 2018, 10, 733.
Hua, F.; West, J.; Barker, R.; Forster, C. Modelling of chlorine decay in municipal water supplies. Water Res. 1999, 33, 2735–2746.
Jonkergouw, P.M.; Khu, S.-T.; Savic, D.A.; Zhong, D.; Hou, X.Q.; Zhao, H.-B. A variable rate coefficient chlorine decay model. Environ. Sci. Technol. 2009, 43, 408–414.
Nejjari, F.; Puig, V.; Pérez, R.; Quevedo, J.; Cugueró, M.; Sanz, G.; Mirats, J. Chlorine decay model calibration and comparison: Application to a real water network. Procedia Eng. 2014, 70, 1221–1230.
Kohpaei, A.J.; Sathasivan, A.; Aboutalebi, H. Effectiveness of parallel second order model over second and first order models. Desalin. Water Treat. 2011, 32, 107–114.
Powell, J.C.; Hallam, N.B.; West, J.R.; Forster, C.F.; Simms, J. Factors which control bulk chlorine decay rates. Water Res. 2000, 34, 117–126.
Clark, R.M.; Sivaganesan, M. Predicting chlorine residuals in drinking water: Second order model. J. Water Resour. Plan. Manag. 2002, 128, 152–161.
Li, X.; Li, C.; Bayier, M.; Zhao, T.; Zhang, T.; Chen, X.; Mao, X. Desalinated seawater into pilot-scale drinking water distribution system: Chlorine decay and trihalomethanes formation. Desalin. Water Treat. 2016, 57,19149–19159.
United States Environmental Protection Agency (EPA). Chlorine, Total Residual (Spectrophotometric, DPD); EPA-NERL: 330.5; EPA: Cincinnati, OH, USA, 1978.
Polman, H.; Verhaart, F.; Bruijs, M. Impact of biofouling in intake pipes on the hydraulics and efficiency of pumping capacity. Desalin. Water Treat. 2013, 51, 997–1003.
Rajagopal, S.; Van der Velde, G.; Van der Gaag, M.; Jenner, H.A. How effective is intermittent chlorination to control adult mussel fouling in cooling water systems? Water Res. 2003, 37, 329–338.
Bruijs, M.C.; Venhuis, L.P.; Daal, L. Global Experiences in Optimizing Biofouling Control through PulseChlorination®. 2017. Available online: https://www.researchgate.net/publication/318561645_Global_Experiences_in_Optimizing_Biofouling_Co ntrol_through_Pulse-ChlorinationR (accessed on 1 May 2020).
Kim, H.; Hao, O.J.; McAvoy, T.J. Comparison between model-and pH/ORP-based process control for an AAA system. Tamkang J. Sci. Eng. 2000, 3, 165–172.
Brdys, M.; Chang, T.; Duzinkiewicz, K. Intelligent Model Predictive Control of Chlorine Residuals in Water Distribution Systems, Bridging the Gap: Meeting the World’s Water and Environmental Resources Challenges. In Proceedings of the ASCE Water Resource Engineering and Water Resources Planning and Management, July 30–August 2, 2000; pp. 1–11

PDF 원문 보기

Fig 2(b) Observed velocity field for aspect ratio 0.25(Sukhodolov 2002)

고정 베드의 불침투성 토양에서 흐름 패턴의 수치 시뮬레이션

NUMERICAL SIMULATION OF FLOW PATTERN IN SERIES OF IMPERMEABLE GROYNES IN FIXED BED

Kafle, Mukesh Raj¹
¹Asst. Professor, Department of Civil Engineering, Institute of Engineering, Pulchowk Campus, Nepal
Email: mkafle@pcampus.edu.np

Abstract

This paper presents a numerical simulation of recirculating flow patterns in groyne fields. Moreover, it entails the concept determination of proper spacing of vertical unsubmerged and impermeable groynesin seriesto control the bank erosion. Flow pattern between the groynes varies along their space. The flow in groyne field may significantly affect the flow change, bed change, bank erosion and condition of habitat. In this regard, an assessment of flow along the space of groynes will yield important data needed to diversify the object of groyne installation. So, knowledge about determination of the proper spacing of groynes in groyne field is important. Space of vertical groynes was set from 1.5 to 10 times the length of groynes. The velocity field between groynes was simulated by using Computational Fluid Dynamics (CFD) model Nays 2D. Simulated velocity field was compared with existing experimentaldata for the same parameter, which agreed satisfactorily. Based on simulated results,the optimal spacing of vertical groynes to control the bank erosion was recommended.

이 논문은 groyne 필드에서 재순환 흐름 패턴의 수치 시뮬레이션을 제공합니다. 더욱이, 그것은 제방 침식을 제어하기 위해 수직 비침수 및 불침투성 그로이네신 시리즈의 적절한 간격의 개념 결정을 수반합니다. groynes 사이의 흐름 패턴은 공간에 따라 다릅니다. groyne field의 흐름은 흐름 변화, 하상 변화, 제방 침식 및 서식지 상태에 중대한 영향을 미칠 수 있습니다. 이와 관련하여, groyne 공간을 따른 흐름의 평가는 groyne 설치 대상을 다양화하는 데 필요한 중요한 데이터를 산출할 것입니다. 따라서, groyne field에서 groyne의 적절한 간격 결정에 대한 지식이 중요합니다. 수직 여백의 간격은 여아 길이의 1.5배에서 10배 사이로 설정하였다. groyne 사이의 속도장은 CFD(Computational Fluid Dynamics) 모델 Nays 2D를 사용하여 시뮬레이션되었습니다. 시뮬레이션된 속도장은 동일한 매개변수에 대해 기존 실험 데이터와 비교되었으며 만족스럽게 일치했습니다. 모의 결과를 바탕으로 제방 침식을 억제하기 위한 최적의 수직 제방 간격을 제안하였다.

Introduction
Spur dikes or groynes are used to protect river banks from erosion and also keep the channel
navigable.Depending upon the flow characteristics, spur-dikes may be classified as submerged and unsubmerged. Also, based on the permeability, spur dikes are further classified as permeable and
impermeable. Herein, un-submerged !impermeable spur dikes are dealt. These structures are built from the river bank into the stream flow and usually built in group. Construction of groyne against the flow causes significant changes in flow pattern in channel. Those changes may result in scour phenomenon around groynes which may lead structure instability and changes in river morphology. Moreover, in series of groynes, spacing of groynes leads different types of recirculating flow patterns.Therefore, investigating the characteristics of flow pattern around groynes have been a great interest in river engineering. Numerous researchers like Sukhodolov et al. (2002), Hao Zhang et al.(2009), Beheshti (2010), Duan (2009), Naji(2010), Karami(2011) made a variety of experiments in order to determine the flow pattern around groynes. Most of these researchers studied effect of single groyne, while using series of groynes is more effective in protection of rivers. Besides experimental studies, variety of CFD models have been developed for computing flow pattern around hydraulic structures; like Fluent, Flow 3D, Nays 2D, Nays CUBE and SSIIM. In this study, Nays 2D numerical modelling has been used to investigate flow and recirculating pattern around a series of groynes and streamlines including components of velocities.

Flow pattern in groyne fields
Under conditions where the groynes are not submerged, the groyne fields are not really part of the wetted cross section of a river. Because of that, the flow pattern in the groyne-field is not directly the result of the discharge in the main channel. Reducing the main stream velocity has no effect on the flow pattern itself, whereas lowering the water level does (Uijttewaal et al.2001). Moreover, the flow pattern inside a groyne field may change with the change of its geometry, location along the river (inner curve, outer curve, or straight part), and/ or the groynes orientation( Przedwojski et al.1995). However, there is an indirect effect of the discharge on the flow pattern in the groyne field. Because of the flow that is diverted from the main channel into the groyne fields, water flows into the groyne field with low velocity through the downstream half of the interfacial section between the groyne field and the main channel. This water flows back to the main channel through a small width of, just downstream the upstream groyne of the groyne field ( Termes et al.1991). Flow separates on a groyne head and forms a secondary flow represented by a large scale vortex with a vertical axis of rotation called primary gyre. Deflection of the flow inside the groyne field by banks and upstream groynes leads to the development of a secondary gyre with an opposite direction of rotation to the primary gyre. Location, mutual interactions, and energy exchange between gyres are the factors that create a specific recirculation pattern, and, consequently assuming correspondence with sedimentation processes, they define deposition patterns.
Model Formulation
The CFD model selected for this study is the publically available software NAYS 2D (iRIC 2.0), which is an analytical solver for calculation of unsteady two-dimensional plane flow and riverbed deformation using boundary-fitted coordinates within general curvilinear coordinates. A numerical channel of length 8.0m and width 0.9m was created with grid size of 0.01m im stream wise and 0.03m in cross stream directions. Groynes or spur dikes of length 0.15 and width 0.01m were chosen in series. Groyne field with various aspect ratio (b/x) 0.7, 0.25, 0.17, 0.125 and 0.10, where b=length of spur dike, x=spacing of two dikes. Discharge of 0.0175 m3 /s was applied. For boundary conditions, water surface at downstream and velocity at upstream were considered as uniform flow. Relaxation coefficient for water surface calculation was considered as 0.8. For the finite-difference method, the CIP method was applied to the advection terms in equations of motion. For the turbulent field calculation, Constant eddy viscosity, Zero-equation model and k-G models were applied and compared. The model!s accuracy in predicting the velocity magnitudes is evaluated using statistical parameters- mean absolute error (MAE), mean square error(MSE), and root mean square error (RMSE). The comparison of results shows the importance of selecting an appropriate turbulence model in simulating flow field around a spur dike. From the comparison, k-I model is found superior over zero energy model and eddy viscosity model. So, k-I model is chosen as appropriate turbulence closure model.
Model!s Validation
The capability of CFD model Nays 2D to simulate the velocity field and recirculation pattern in groyne field was compared with experimental data of laboratory experiments by Sukhodolov et al. (2002). The numerical simulation was validated for aspect ratio (R=b/x=0.7) and R=0.25. For aspect ratio R=0.7, one gyre system occupies the whole area of the groyne field. The areas with lower-than-average velocity values are clearly seen in the central part of the gyre and near its corners. Velocities increase towards the margins of the gyre. For aspect ratio R=0.25, two gyre velocity fields were observed in the groyne field. In the downstream part of the groyne field a large gyre, covering two-thirds of the area is clearly visible. The left part(upstream) contains second gyre rotating much more slowly and in the direction opposed to the primary gyre. The simulated and observed velocity field pattern and gyre found satisfactorily agreed. Now, after validation, the model was used for further analysis of velocity field for various aspect ratios.

Results and Discussions
The calibrated model was applied to five different cases of un-submerged and impermeable groyne fields with aspect ratios R=0.70,0.25,0.17,0.125 & 0.10 and flow pattern was numerically simulated. For aspect ratio R=0.7 i.e x/b=1.5, Fig 1(a) only one lateral primary gyre was formed inside the groyne field. The circulation pattern in this case is distinguished by the main flow that is deflected outside the groyne field. The developed primary gyre prevents the main flow from penetrating the groyne field. Therefore, this pattern is desirable for navigation purposes as a continuous deep channel is maintained along the face of the groyne field. Simulated velocity pattern satisfactorily agrees with the observed velocity field Fig 1(b) for the same aspect ratio by Sukhodolov (2002). The spacing of the groyne was further increased maintaining aspect ratio R= 0.25 i. e x/b=4 Fig 2(a) and flow pattern inside the groyne field was simulated. In this case, in the downstream part of the groyne field, a primary gyre occupying almost two-third area was formed. In addition, deflection of the flow inside the groyne field by banks and upstream groynes leads to the development of a secondary gyre with an opposite direction of rotation to the primary gyre covering almost one-third part of the groyne field. Likewise in the first case, the main current is maintained deflected outside the groyne field. Simulated velocity pattern satisfactorily agrees with the observed velocity field Fig 2(b) for the same aspect ratio by Sukhodolov (2002). The spacing of the groyne was further increased maintaining aspect ratio R=0.17 i.e x/b=6. In this case the flow pattern was similar to the aspect ratio R=0.25. The spacing of the groynes was further increased maintaining aspect ratio R=0.125 i. e x/b=8. In this case, similar to the previous scenarios two longitudinal gyres but with different positions are formed. The main current is directed in to the groyne field (Fig 3) creating a much more stronger eddy near the upstream groyne and greater turbulence along the upstream face and at the groyne lower head. As the spacing between groynes increased maintaining aspect ratio R=0.10 i. e x/b=10 (Fig 4), still primary and secondary gyres are generated. The formed gyres deflect the main flow thus preventing to enter in to the groyne field in upstream part. However, in the downstream of the primary gyre and just upstream of the second groyne, the flow attacks the bank directly. The resultant velocity profiles at the deflected region y/b=3 were plotted and how the spacing of second groyne affect the result was analyzed. Spacing of groynes makes little change in upstream resultant velocity. However, in the deflected region, its effect is significant. Higher value of spacing of groyne leads higher average deviation in resultant velocity. For aspect ratio R=0.7, the average deviation estimated as 0.02%. In the case of aspect ratio R=0.25, this value was reached to 1.57%. Further increment of spacing i. e decreasing the aspect ratio R=0.17, average deviation was found 3.82%. For the aspect ratio R=0.125, that value was estimated as 4.16%.
Conclusions
Geometry of the groyne fields; width and length of the groyne field mainly cause the specific flow patterns including number and shape of eddies or gyres. Eddies developed inside the groyne field deflects the main flow preventing it entering into the dead zone. An aspect ratio close to unity gives rise to a single eddy. A smaller aspect ratio (higher spacing between groynes) gives room to two stationary eddies, a large one called primary eddy, in the downstream part of the groyne field, and a smaller secondary eddy emerges near the upstream groyne. The extreme long groyne field -case of length to width ratio of larger thaneight shows penetration of main flow into the groyne field. The two eddies remain in a relatively stable position, while the main flow zone starts to penetrate into groyne field further downstream. In all cases, there is an eddy detaches from the upstream groyne tip that travels along the main channel groyne field interface and eventually merges with the primary eddy. The simulated results indicate that the spacing of groynes or spur dikes from the controlling of bank erosion point of view should be limited within six times the length of groyne.

Fig 3 Computed velocity field for aspect ratio 0.125

Fig 4 Computed velocity field for aspect ratio 0.10

Fig 5 Resultant velocity profiles at y/b=3

References

Holtz, K.P Numerical simulation of recirculating flow at groynes.Å Computer Methods in Water Resources, Vol 2, No 2 (1991).
Hossein, Bassar; Abdollah, Ardeshir; Hojat, Karami. Numerical simulation of flow pattern around spur dikes series in rigid bed.Å 9th international congress on civil engineering, May 8- 10,2012, Isfahan University of Technology (IUT) , Isfahan, Iran (2012).
Kang, J.G; Yeo, H.K; Kim,S.J An experimental study on a characteristics of flow around groyne area by install conditions.Å www.SciRP.org/journal/eng(2012).
Shimizu,Y; Nelson,JIntroduction of Nays solver in iRIC.Åwww.i-ric.org(2012).
Sukhodolov, A. Uijttewaal, W. S. J., and Engelhardt, C. On the correspondence between morphological and hydro dynamical patterns of groyne fields.Å Earth Surf. Processes Landforms, 27(3) (2002).
Uijttewall, W.S.J; Lehman,D; VanMazijk,A. Exchange process between a river and its groyne fields-model experiments.Å Journal of Hydraulic Engineering, ASCE, 127(11) (2001).
Uijttewall, W.S.J Groyne field velocity patterns determined with particle tracking
velocimetryÅ.28th IAHR congress, Graz, Austria (1999).
Yossef, Mohamed Flow details near groynes: Experimental investigations.Å Journal of Hydraulic Engineering, ASCE, 137 (2011).

CFD 사용: 유압 구조 및 농업에서의 응용

USO DE CFD COMO HERRAMIENTA PARA LA MODELACIÓN Y PREDICCIÓN NUMÉRICA DE LOS FLUIDOS: APLICACIONES EN ESTRUCTURAS HIDRÁULICAS Y AGRICULTURA

Cruz Ernesto Aguilar-Rodriguez^1*; Candido Ramirez-Ruiz²; Erick Dante Mattos Villarroel³

¹Tecnológico Nacional de México/ITS de Los Reyes. Carretera Los Reyes-Jacona, Col. Libertad. 60300. Los Reyes de Salgado, Michoacán. México.

ernesto.ar@losreyes.tecnm.mx – 3541013901 (*Autor de correspondencia)

²Instituto de Ciencias Aplicadas y Tecnología, UNAM. Cto. Exterior S/N, C.U., Coyoacán, 04510, Ciudad de México. México. ³Riego y Drenaje. Instituto Mexicano de Tecnología del Agua. Paseo Cuauhnáhuac 8532, Progreso, Jiutepec, Morelos, C.P. 62550. México.

Abstract

공학에서 유체의 거동은 설명하기에 광범위하고 복잡한 과정이며, 유체역학은 유체의 거동을 지배하는 방정식을 통해 유체 역학 현상을 분석할 수 있는 과학 분야이지만 이러한 방정식에는 전체 솔루션이 없습니다. . 전산유체역학(Computational Fluid Dynamics, 이하 CFD)은 수치적 기법을 통해 방정식의 해에 접근할 수 있는 도구로, 신뢰할 수 있는 계산 모델을 얻기 위해서는 물리적 모델의 실험 데이터로 평가해야 합니다. 수력구조물에서 선형 및 미로형 여수로에서 시뮬레이션을 수행하고 배출 시트의 거동과 현재의 폭기 조건을 분석했습니다. 침강기에서 유체의 특성화를 수행하고 필요한 특성에 따라 사체적, 피스톤 또는 혼합의 분수를 수정하는 것이 가능합니다. 농업에서는 온실 환경을 특성화하고 환경에 대한 재료의 디자인, 방향 및 유형 간의 관계를 찾는 데 사용할 수 있습니다. 발견된 가장 중요한 결과 중 온실의 길이와 설계가 환기율에 미칠 수 있는 영향으로 온실의 길이는 높이의 6배 미만인 것이 권장됩니다.

키워드: Computational Fluid Dynamics, 온실,

Spillway, Settler 기사: COMEII-21048 소개

CFD는 유체 운동 문제에 대한 수치적 솔루션을 얻어 수리학적 현상을 더 잘 이해할 수 있게 함으로써 공간 시각화를 가능하게 하는 수치 도구입니다. 예를 들어, 수력 공학에서 벤츄리(Xu, Gao, Zhao, & Wang, 2014) 워터 펌핑(ȘCHEAUA, 2016) 또는 개방 채널 적용( Wu et 알., 2000).

문헌 검토는 실험 연구에서 검증된 배수로의 흐름 거동에 대한 수리학적 분석을 위한 CFD 도구의 효율성을 보여줍니다. 이 검토는 둑의 흐름 거동에 대한 수리학적 분석을 위한 CFD의 효율성을 보여줍니다. Crookston et al. (2012)는 미로 여수로에 대해 Flow 3D로 테스트를 수행했으며, 배출 계수의 결과는 3%에서 7%까지 다양한 오류로 실험적으로 얻은 결과로 허용 가능했으며 연구 결과 측면에 저압 영역이 있음을 발견했습니다. 익사 방식으로 작업할 때 위어의 벽. Zuhair(2013)는 수치 모델링 결과를 Mandali weir 원형의 실험 데이터와 비교했습니다.

최근 연구에서는 다양한 난류 모델을 사용하여 CFD를 적용할 가능성이 있음을 보여주었습니다. 그리고 일부만이 음용수 처리를 위한 침적자의 사례 연구를 제시했으며, 다른 설계 변수 중에서 기하학적인 대안, 수온 변화 등을 제안했습니다. 따라서 기술 개발로 인해 설계 엔지니어가 유체 거동을 분석하는 데 CFD 도구를 점점 더 많이 사용하게 되었습니다.

보호 농업에서 CFD는 온실 환경을 모델링하고 보조 냉방 또는 난방 시스템을 통해 온실의 미기후 관리를 위한 전략을 제안하는 데 사용되는 기술이었습니다(Aguilar Rodríguez et al., 2020).

2D 및 3D CFD 모델을 사용한 본격적인 온실 시뮬레이션은 태양 복사 모델과 현열 및 잠열 교환 하위 모델의 통합을 통해 온실의 미기후 분포를 연구하는 데 사용되었습니다(Majdoubi, Boulard, Fatnassi, & Bouirden, 2009). 마찬가지로 이 모델을 사용하여 온실 설계(Sethi, 2009), 덮개 재료(Baxevanou, Fidaros, Bartzanas, & Kittas, 2018), 시간, 연중 계절( Tong, Christopher, Li, & Wang, 2013), 환기 유형 및 구성(Bartzanas, Boulard, & Kittas, 2004).

CFD 거래 프로그램은 사용자 친화적인 플랫폼으로 설계되어 결과를 쉽게 관리하고 이해할 수 있습니다.

…

Figura 1. Distribución de presiones y velocidades en un vertedor de pared delgada.

Figura 2. Perfiles de velocidad y presión en la cresta vertedora.

Figura 3. Condiciones de aireación en vertedor tipo laberinto. (A)lámina adherida a la pared del
vertedor, (B) aireado, (C) parcialmente aireado, (D) ahogado.

Figura 4. Realización de prueba de riego.

Figura 5. Efecto de la posición y dirección de los calefactores en un invernadero a 2 m del suelo.

Figura 6. Indicadores ambientales para medir el confort ambiental de los cultivos.

Figura 7. Líneas de corriente dentro del sedimentador experimental en estado estacionario (Ramirez-Ruiz, 2019).

Referencias Bibliográficas

Aguilar-Rodriguez, C.; Flores-Velazquez, J.; Ojeda-Bustamante, W.; Rojano, F.; Iñiguez-
Covarrubias, M. 2020. Valuation of the energyperformance of a greenhouse with

an electric heater using numerical simulations. Processes, 8, 600.

Aguilar-Rodriguez, C.; Flores-Velazquez, J.; Rojano, F.; Ojeda-Bustamante, W.; Iñiguez-
Covarrubias, M. 2020. Estimación del ciclo de cultivo de tomate (Solanum

lycopersicum L.) en invernadero, con base en grados días calor (GDC) simulados
con CFD. Tecnología y ciencias del agua, ISSN 2007-2422, 11(4), 27-57.
Al-Sammarraee, M., y Chan, A. (2009). Large-eddy simulations of particle sedimentation
in a longitudinal sedimentation basin of a water treatment plant. Part 2: The effects
of baffles. Chemical Engineering Journal, 152(2-3), 315-321.
doi:https://doi.org/10.1016/j.cej.2009.01.052.
Bartzanas, T.; Boulard, T.; Kittas, C. 2004. Effect of vent arrangement on windward
ventilation of a tunnel greenhouse. Biosystems Engineering, 88(4).
Baxevanou, C.; Fidaros, D.; Bartzanas, T.; Kittas, C. 2018. Yearly numerical evaluation of
greenhouse cover materials. Computers and Electronics in Agriculture, 149, 54–

DOI: https://doi.org/10.1016/j.compag.2017.12.006.
Crookston, B. M., & Tullis, B. P. 2012. Labyrinth weirs: Nappe interference and local
submergence. Journal of Irrigation and Drainage Engineering, 138(8), 757-765.
Fernández, J. M. 2012. Técnicas numéricas en Ingeniería de Fluidos: Introducción a la
Dinámica de Fluidos Computacional (CFD) por el Método de Volumen Finito;
Reverté, Barcelona, pp. 98-294.
Goula, A., Kostoglou, M., Karapantsios, T., y Zouboulis, A. (2008). The effect of influent
temperature variations in a sedimentation tank for potable water treatment— A
computational fluid dynamics study. Water Research, 42(13), 3405-3414.
doi://doi.org/10.1016/j.watres.2008.05.002.
Majdoubi, H.; Boulard, T.; Fatnassi, H.; Bouirden, L. 2009. Airflow and microclimate
patterns in a one-hectare Canary type greenhouse: an experimental and CFD
assisted study. Agricultural and Forest Meteorology, 149(6-7), 1050-1062.
Ramirez-Ruiz Candido (2019). Estudio hidrodinámico de sedimentadores de alta tasa en
plantas potabilizadoras utilizando dinámica de fluidos computacional (CFD).
Universidad Nacional Autónoma de México. Tesis de maestría.
Sánchez, J. M. C., & Elsitdié, L. G. C. 2011. Consideraciones del mallado aplicadas al
cálculo de flujos bifásicos con las técnicas de dinámica de fluidos computacional.
J. Introd. Inv. UPCT., 4, 33-35.
Sethi, V.P. 2009. On the selection of shape and orientation of a greenhouse: Thermal
modeling and experimental validation, Sol. Energy, 83, 21–38.
ȘCHEAUA, F. 2016. AGRICULTURAL FIELD IRRIGATION SOLUTION BASED ON
VENTURI NOZZLE γ 2 g γ 2 g. JOURNAL OF INDUSTRIAL DESIGN AND
ENGINEERING GRAPHICS, 2(1), 31–35.

Tong, G.; Christopher, D.; Li, T.; Wang, T. 2013. Passive solar energy utilization: a review
of cross-section building parameter selection for Chinese solar greenhouses.
Renewable and Sustainable Energy Reviews, 26, 540-548.

Xu, Y., Gao, L., Zhao, Y., & Wang, H. 2014. Wet gas overreading characteristics of a long-
throat Venturi at high pressure based on CFD. Flow Measurement and

Instrumentation, 40, 247–255. https://doi.org/10.1016/j.flowmeasinst.2014.09.004
Wu, W., Rodi, W y Wenka, T. 2000. 3D numerical modeling of flow and sediment transport
in open channels. ASCE Journal of Hydraulic Engineering. Vol 126 Num 1.
Zuhair al zubaidy, Riyadh. 2013. Numerical Simulation of Two-Phase Flow.
En:International Journal of Structural and Civil Engineering Research. Vol 2, No 3;
13p

원문 보기

Fig. 4. Meshed quarter aluminum model with HAZ regions and support steel plates.

Benchmark study on slamming response of flat-stiffened plates considering fluid-structure interaction

유체-구조 상호작용을 고려한 평판 보강판의 슬래밍 응답에 대한 벤치마크 연구

Dac DungTruong^abBeom-SeonJang^aCarl-ErikJanson^cJonas W.Ringsberg^cYasuhiraYamada^dKotaTakamoto^fYasumiKawamura^eHan-BaekJu^a
^aResearch Institute of Marine Systems Engineering, Department of Naval Architecture and Ocean Engineering, Seoul National University, Seoul, South Korea
^bDepartment of Engineering Mechanics, Nha Trang University, Nha Trang, Viet Nam
^cDivision of Marine Technology, Department of Mechanics and Maritime Sciences, Chalmers University of Technology, Gothenburg, Sweden
^dNational Maritime Research Institute, National Institute of Maritime, Port and Aviation Technology, Tokyo, Japan
^eDepartment of Systems Design for Ocean-Space, Yokohama National University, Kanagawa, Japan
^fDepartment of Mechanical Systems Engineering, Tokyo University of Agriculture and Technology, Tokyo, Japan

ABSTRACT

이 논문은 해양구조물의 평보강판의 슬래밍 반응에 대한 벤치마크 연구를 제시합니다. 목표는 유체-구조 상호작용(FSI) 시뮬레이션 방법론, 모델링 기술 및 슬래밍 압력 예측에 대한 기존 연구원의 경험을 비교하는 것이었습니다.

수치 FSI 시뮬레이션을 위해 가장 일반적인 상용 소프트웨어 패키지를 사용하는 3개의 연구 그룹(예: LS-Dyna ALE, LS-Dyna ICFD, ANSYS CFX 및 Star-CCM+/ABAQUS)이 이 연구에 참여했습니다.

공개 문헌에서 입수할 수 있는 경량 선박과 같은 바닥 구조의 평평한 강화 알루미늄 판에 대한 습식 낙하 시험 데이터는 FSI 모델링의 검증에 활용되었습니다. 형상 모델 및 재료 속성을 포함한 실험 조건의 요약은 시뮬레이션 전에 참가자에게 배포되었습니다.

충돌 속도와 강판의 강성이 슬래밍 응답에 미치는 영향을 조사하기 위해 해양 설비에 사용되는 실제 치수를 갖는 평판 보강 강판에 대한 매개변수 연구를 수행했습니다. 보강판에 작용하는 전체 수직력에 대한 FE 시뮬레이션 결과와 이러한 힘에 대한 구조적 반응을 참가자로부터 획득하여 분석 및 비교하였다.

앞서 언급한 상용 FSI 소프트웨어 패키지를 사용하여 슬래밍 부하에 대한 신뢰할 수 있고 정확한 예측을 평가했습니다. 또한 FSI 시뮬레이션에서 관찰된 동일한 영구 처짐을 초래하는 등가 정적 슬래밍 압력을 보고하고 분류 표준 DNV에서 제안한 해석 모델 및 슬래밍 압력 계산을 위한 기존 실험 데이터와 비교했습니다.

연구 결과는 등가 하중 모델이 물 충돌 속도와 플레이트 강성에 의존한다는 것을 보여주었습니다. 즉, 등가정압계수는 충돌속도가 증가함에 따라 감소하고 충돌구조가 더 단단해지면 증가한다.

This paper presents a benchmark study on the slamming responses of offshore structures’ flat-stiffened plates. The objective was to compare the fluid-structure interaction (FSI) simulation methodologies, modeling techniques, and established researchers’ experiences in predicting slamming pressure. Three research groups employing the most common commercial software packages for numerical FSI simulations (i.e. LS-Dyna ALE, LS-Dyna ICFD, ANSYS CFX, and Star-CCM+/ABAQUS) participated in this study. Wet drop test data on flat-stiffened aluminum plates of light-ship-like bottom structures available in the open literature was utilized for validation of the FSI modeling. A summary of the experimental conditions including the geometry model and material properties, was distributed to the participants prior to their simulations. A parametric study on flat-stiffened steel plates having actual scantlings used in marine installations was performed to investigate the effect of impact velocity and plate rigidity on slamming response. The FE simulation results for the total vertical forces acting on the stiffened plates and their structural responses to those forces, as obtained from the participants, were analyzed and compared. The reliable and accurate predictions of slamming loads using the aforementioned commercial FSI software packages were evaluated. Additionally, equivalent static slamming pressures resulting in the same permanent deflections, as observed from the FSI simulations, were reported and compared with analytical models proposed by the Classification Standards DNV and existing experimental data for calculation of the slamming pressure. The study results showed that the equivalent load model depends on the water impact velocity and plate rigidity; that is, the equivalent static pressure coefficient decreases with an increase in impact velocity, and increases when impacting structures become stiffer.

Fig. 6. (a) Boundary conditions of water hitting case and (b) water jets at end of the simulation.

Fig. 7. Comparison of prediction and test results for deflection time history of (a) D1 and (b) D2 for Vi = 2.3 m/s.

Fig. 8. Comparison of prediction and test results for maximum deflection with different impact velocities.

Fig. 16. Boundary conditions applied to present FSI simulations (Sym. denotes symmetric, and Cons. denotes constrained)

Fig. 24. Distribution of deflections at moment of maximum deflection in: (a) LS-Dyna ALE, (b) Star-CCM+/ABAQUS, (c) ANSYS CFD, and (d) LSDyna ICFD (unit: m).

Keywords

Benchmark studyEquivalent static pressureFlat-stiffened plateFluid-structure interactionPermanent deflectionSlamming pressure coefficient

References

[1] Von Karman TH. The impact on seaplane floats during landing. Washington, DC: National Advisory Committee for Aeronautics; 1929. Technical note No.: 321.
[2] Wagner VH. Über Stoß- und Gleitvorgange ¨ an der Oberflache ¨ von Flüssigkeiten. Z Angew Math Mech 1932;12(4):193–215.
[3] Chuang SL. Experiments on flat-bottom slamming. J Ship Res 1966;10:10–7.
[4] Chuang SL. Investigation of impact of rigid and elastic bodies with water. Report for Department of the Navy. Washington, DC: United States Department of the
Navy; 1970. Report No.: 3248.
[5] Mori K. Response of the bottom plate of high-speed crafts under impulsive water pressure. J Soc Nav Archit Jpn 1977;142:297–305 [Japanese].
[6] Cheon JS, Jang BS, Yim KH, Lee HSD, Koo BY, Ju HB. A study on slamming pressure on a flat stiffened plate considering fluid–structure interaction. J Mar Sci
Technol 2016;21:309–24.
[7] Truong DD, Jang BS, Ju HB, Han SW. Prediction of slamming pressure considering fluid-structure interaction. Part I: Numerical simulations. Ships Offshore
Struct. https://doi.org/10.1080/17445302.2020.1816732.
[8] Truong DD, Jang BS, Ju HB, Han SW. Prediction of slamming pressure considering fluid-structure interaction. Part II: Derivation of empirical formulations. Mar
Struct. https://doi.org/10.1016/j.marstruc.2019.102700.
[9] Greenhow M, Lin W. Numerical simulation of nonlinear free surface flows generated by wedge entry and wave maker motions. In: Proceedings of the 4th
international conference on numerical ship hydrodynamics, Washington, DC; 1985.
[10] Sun H, Faltinsen OM. Water impact of horizontal circular cylinders and cylindrical shells. Appl Ocean Res 2006;28(5):299–311.
[11] Gingold RA, Monaghan JJ. Smoothed particle hydrodynamics: theory and application to non-spherical stars. Royal Astronomical Society 1977;181:375–89.
[12] Shao S. Incompressible SPH simulation of water entry of a free-falling object. Int J Numer Methods Fluid 2009;59(1):91–115.
[13] Souli M, Ouahsine A, Lewin L. ALE formulation for fluid-structure interaction problems. Comput Methods Appl Mech Eng 2000;190(5):659–75.
[14] Livermore Software Technology Corporation (LSTC). ICFD theory manual incompressible fluid solver in LS-DYNA. Livermore Software Technology Corporation;

[15] Livermore Software Technology Corporation (LSTC). LS-DYNA theoretical manual. Livermore Software Technology Corporation; 2006.
[16] FLOW-3D user’s manual. 2018., version 12.0.
[17] Cd-adapco. STAR-CCM+ User’s manual. 2012., version 7.06.
[18] ANSYS fluent user’s guide. 2015.
[19] ANSYS CFX user’s guide. 2014.
[20] Abaqus user’s manual, version 6.13. SIMULIA; 2013.
[21] Luo HB, Hu J, Guedes Soares C. Numerical simulation of hydroelastic responses of flat stiffened panels under slamming loads. In: Proceedings of the 29th
international conference on ocean, offshore and arctic engineering (OMAE2010); 2010 [Shanghai, China].[22] Yamada Y, Takami T, Oka M. Numerical study on the slamming impact of wedge shaped obstacles considering fluid-structure interaction (FSI). In: Proceedings
of the 22nd international offshore and polar engineering conference (ISOPE2012); 2012 [Rhodes, Greece].
[23] Luo HB, Wang H, Guedes Soares C. Numerical and experimental study of hydrodynamic impact and elastic response of one free-drop wedge with stiffened
panels. Ocean Eng 2012;40:1–14.
[24] Sun H, Wang DY. Experimental and numerical analysis of hydrodynamic impact on stiffened side of three dimensional elastic stiffened plates. Adv Mech Eng
2018;10(4):1–23.
[25] Ma S, Mahfuz H. Finite element simulation of composite ship structures with fluid structure interaction. Ocean Eng 2012;52:52–9.
[26] LSTC. Turek & hron’s FSI benchmark problem. 2012.
[27] Califano A, Brinchmann K. Evaluation of loads during a free-fall lifeboat drop. In: Proceedings of the ASME 32nd international conference on ocean, offshore
and arctic engineering (OMAE2013); 2013 [Nantes, France].
[28] LSTC. 3D fluid elastic body interaction problem. 2014.
[29] Yamada Y, Takamoto K, Nakanishi T, Ma C, Komoriyama Y. Numerical study on the slamming impact of stiffened flat panel using ICFD method – effect of
structural rigidity on the slamming impact. In: Proceedings of the ASME 39th international conference on ocean, offshore and arctic engineering (OMAE2020);
2020 [Florida, USA].
[30] Nicolici S, Bilegan RM. Fluid structure interaction modeling of liquid sloshing phenomena in flexible tanks in flexible tanks. Nucl Eng Des 2013;258:51–6.
[31] DNV. DNV-RP-C205 environmental conditions and environmental loads. Det Norske Veritas; October 2010.
[32] Ahmed YM. Numerical simulation for the free surface flow around a complex ship hull form at different froude numbers. Alex Eng J 2011;50(3):229–35.
[33] Ghadimi P, Feizi Chekab MA, Dashtimanesh A. Numerical simulation of water entry of different arbitrary bow sections. J Nav Architect Mar Eng 2014;11:
117–29.
[34] Park BW, Cho S-R. Simple design formulae for predicting the residual damage of unstiffened and stiffened plates under explosive loadings. Int J Impact Eng
2006;32:1721–36.
[35] Truong DD, Shin HK, Cho S-R. Permanent set evolution of aluminium-alloy plates due to repeated impulsive pressure loadings induced by slamming. J Mar Sci
Technol 2018;23:580–95.
[36] Jones N. Structural impact. first ed. Cambridge, UK: Cambridge University Press; 1989.
[37] Zha Y, Moan T. Ultimate strength of stiffened aluminium panels with predominantly torsional failure modes. Thin-Walled Struct 2001;39:631–48.
[38] Sensharma P, Collette M, Harrington J. Effect of welded properties on aluminum structures. Ship Structure Committee SSC-4 2010.
[39] ABS. Guide for slamming loads and strength assessment for vessels. 2011.
[40] Villavicencio R, Sutherland L, Guedes Soares C. Numerical simulation of transversely impacted, clamped circular aluminium plates. Ships Offshore Struct 2012;7(1):31–45.
[41] Material properties database. https://www.varmintal.com/aengr.htm, Assessed date: 16 May 2020.
[42] Ringsberg JW, Andri´c J, Heggelund SE, Homma N, Huang YT, Jang BS, et al. Report of the ISSC technical committee II.1 on quasi-static response. In:
Kaminski ML, Rigo P, editors. Proceedings of the 20th international ship and offshore structures congress (ISSC 2018), vol. 1. IOS Press BV; 2018. p. 226–31.
[43] Shin HK, Kim S-C, Cho S-R. Experimental investigations on slamming impacts by drop tests. J Soc Nav Archit Korea 2010;47(3):410–20 [Korean].
[44] Huera-Huarte FJ, Jeon D, Gharib M. Experimental investigation of water slamming loads on panels. Ocean Eng 2011;38:1347–55.

PDF View

Fig. 8. Pressure distribution during the infiltration of preform with the 50 ¯m particles and 20 % starches: (a) 25 % filled, (b) 57 % filled, and (c) 99 % filled.

Experimental study and numerical simulation of infiltration of AlSi12 alloys into Si porous preforms with micro-computed tomography inspection characteristics

마이크로 컴퓨터 단층 촬영 검사 특성을 가진 Si 다공성 프리폼에 AlSi12 합금의 침투에 대한 실험적 연구 및 수치 시뮬레이션

Ruizhe LIU¹ and Haidong ZHAO¹,³
¹National Engineering Research Center of Near-Net-Shape Forming for Metallic Materials, South China University of Technology,
Guangzhou 510640, China

Abstract

전분 함량(10, 20 및 30%)과 입자 크기(20, 50 및 90 m)가 다른 실리콘 입자 예비 성형체는 압축 성형 및 열처리를 통해 제작되었습니다. 프리폼의 기공 특성은 고해상도(³1 m) 3차원(3D) X선 마이크로 컴퓨터 단층 촬영(V-CT)으로 검사되었습니다. AlSi12 합금의 프리폼으로의 침투는 진공 보조 압력 침투 장치에서 800 °C 및 400 kPa의 조건에서 서로 다른 압력 적용 시간(3, 8 및 15초)으로 수행되었습니다. 고해상도(³500 nm) 수직 주사 백색광 간섭 프로파일로미터를 사용하여 복합 재료의 전면을 감지했습니다. Navier-Stokes 방정식을 기반으로 하는 ¯-CT 검사에서 실제 기공 형상을 고려하여 침투를 미시적으로 시뮬레이션했습니다. 그 결과 전분 함량과 입자크기가 증가할수록 복합재료의 표면적이 증가하는 것으로 나타났다. 전분 함량과 비교하여 입자 크기는 전면 표면적에 더 많은 영향을 미칩니다. 시뮬레이션에서 침투가 진행됨에 따라 액체 AlSi12의 압력이 감소했습니다. 복합재의 잔류 기공은 침투와 함께 증가했습니다. 실험 및 시뮬레이션 결과에 따르면 침투 방향을 따라 더 큰 압력 강하가 복합 재료의 더 많은 잔류 기공을 유도합니다.

Silicon particle preforms with different starch contents (10, 20 and 30%) and particle sizes (20, 50 and 90 ¯m) were fabricated by compression mold forming and heat treatment. The pore characteristics of preforms were inspected with a high-resolution (³1 ¯m) three-dimensional (3D) X-ray micro-computed tomography (¯-CT). The infiltration of AlSi12 alloys into the preforms were carried out under the condition of 800 °C and 400 kPa with different pressure-applied times (3, 8 and 15 s) in a vacuum-assisted pressure infiltration apparatus. A highresolution (³500 nm) vertical scanning white light interfering profilometer was used to detect the front surfaces of composites. The infiltration was simulated at micro-scale by considering the actual pore geometry from the ¯- CT inspection based on the Navier-Stokes equation. The results demonstrated that as the starch content and particle size increased, the front surface area of composite increased. Compared with the starch content, the particle size has more influence on the front surface area. In the simulation, as the infiltration progressed, the pressure of liquid AlSi12 decreased. The residual pores of composites increased with infiltration. According to the experiment and simulation results, a larger pressure drop along the infiltration direction leads to more residual pores of composites.

Fig. 1. Size distributions of Si particles.

Fig. 2. Schematic of different locations of composites.

Fig. 3. Three-dimensional geometry with the reconstruction technology, enmeshment and infiltration parameters of Si preforms: (a) geometry, and (b) meshes and flow direction.

Fig. 4. Number-based frequencies of effective pore radius and throat radius: (a) effective pore radius of preforms with the 50 ¯m particles, (b) effective throat radius of preforms with the 50 ¯m particles, (c) effective pore radius of preforms with the 20 % starches, and (d) effective throat radius of preforms with the 20 % starches.

Fig. 5. 3D topological morphologies of front surfaces of composites: (a) 50 ¯m-10 %, (b) 50 ¯m-20 %, (c) 50 ¯m-30 %, (d) 20 ¯m-20 %, and (e) 90 ¯m-20 %.

Fig. 9. Pressure distributions of liquid AlSi12 during the infiltration of preforms: (a) different fill fractions, (b) different starch contents, and (c) different particle sizes.

Fig. 10. Metallographs of composites: (a) different locations of composite with the 20 ¯m particles and 20 % starches, and (b) different locations of composite with the 90 ¯m particles and 20 % starches.

Fig. 11. Area fractions of residual pores of composites: (a) 50 ¯m (different starch contents), and (b) 20 % (different particle sizes).

References

1) V. G. Resmi, K. M. Sree Manu, V. Lakshmi, M.
Brahmakumar, T. P. D. Rajan, C. Pavithran and B. C.
Pai, J. Porous Mat., 22, 14451454 (2015).
2) C. García-Cordovilla, E. Louis and J. Narciso, Acta
Mater., 47, 44614479 (1999).
3) D. B. Miracle, Compos. Sci. Technol., 65, 25262540
(2005).
4) J. M. Chiou and D. D. L. Chung, J. Mater. Sci., 28,
14471470 (1993).
5) Q. G. Zhang and M. Y. Gu, J. Compos. Mater., 40, 471
478 (2006).
6) C. M. Lawrence Wu and G. W. Han, Compos. Part AAppl. S., 37, 18581862 (2006).
7) X. Y. Cai, X. W. Yin, X. K. Ma, X. M. Fan, Y. Z. Cai,
J. P. Li, L. F. Cheng and L. T. Zhang, Ceram. Int., 42,
1014410150 (2016).
8) J. M. Molina, E. Piñero, J. Narciso, C. GarcíaCordovilla and E. Louis, Curr. Opin. Solid St. M., 9,
202210 (2005).
9) A. Léger, L. Weber and A. Mortensen, Acta Mater., 91,
5769 (2015).
10) Y. Q. Ma, L. H. Qi, W. G. Zheng, J. M. Zhou and L. Y.
Ju, T. Nonferr. Metal. Soc., 23, 19151921 (2013).
11) J. T. Tian, E. Piñero, J. Narciso and E. Louis, Scripta
Mater., 53, 14831488 (2005).
12) J. Narciso, A. Alonso, A. Pamies, C. García-Cordovilla
and E. Louis, Metall. Mater. Trans. A, 26A, 983990
(1995).
13) J. Roger, M. Avenel and L. Lapuyade, J. Eur. Ceram.
Soc., 40, 18591868 (2020).
14) J. Roger, M. Avenel and L. Lapuyade, J. Eur. Ceram.
Soc., 40, 18691876 (2020).
15) R. Scardovelli and S. Zaleski, Annu. Rev. Fluid Mech.,
31, 567603 (1999).
16) H. D. Zhao, I. Ohnaka and J. D. Zhu, Appl. Math.
Model., 32, 185194 (2008).
17) Y. He, A. E. Bayly, A. Hassanpour, F. Muller, K. Wu
and D. M. Yang, Powder Technol., 338, 548562
(2018).
18) K. D. Nikitin, K. M. Terekhov and Y. V. Vassilevski,
Appl. Math. Lett., 86, 236242 (2018).
19) J. F. Xiao, X. Liu, Y. M. Luo, J. C. Cai and J. F. Xu,
Colloid. Surface. A, 591, 124572 (2020).
20) N. Birgle, R. Masson and L. Trenty, J. Comput. Phys.,
368, 210235 (2018).
21) M. Chaaban, Y. Heider and B. Markert, Int. J. Heat
Fluid Fl., 83, 108566 (2020).
22) S. Zhang, M. J. Zhu, X. Zhao, D. G. Xiong, H. Wan,
S. X. Bai and X. D. Wang, Compos. Part A-Appl. S., 90,
7181 (2016).
23) J. Roger, L. Guesnet, A. Marchais and Y. Le Petitcorps,
J. Alloy. Compd., 747, 484494 (2018).
24) Q. Wan, H. D. Zhao and C. Zou, ISIJ Int., 54, 511515
(2014).
25) F. Liu, H. D. Zhao, R. S. Yang and F. Z. Sun, Mater.
Today Commun., 19, 114123 (2019).
26) D. Roussel, A. Lichtner, D. Jauffrès, J. Villanova, R. K.
Bordia and C. L. Martin, Scripta Mater., 113, 250253
(2016).
27) M. Fukushima, T. Ohji, H. Hyuga, C. Matsunaga and Y.
Yoshizawa, J. Mater. Res., 32, 32863293 (2017).
28) M. Fukushima, H. Hyuga, C. Matsunaga and Y.
Yoshizawa, J. Am. Ceram. Soc., 101, 32663270
(2018).
29) R. Z. Liu, H. D. Zhao, H. Long and B. Xie, Mater.
Charact., 137, 370378 (2017).
30) B. Xie, H. D. Zhao, H. Long, J. L. Peng and R. Z. Liu,
Ceram. Int., 45, 2392423933 (2019).
31) R. Z. Liu, H. D. Zhao and B. Xie, Transport Porous
Med., 131, 10531063 (2020).
32) Y. Li, H. W. Chen, F. Q. Wang, X. L. Xia and H. P. Tan,
Infrared Phys. Techn., 113, 103646 (2021).
33) P. Tahmasebi, M. Sahimi, A. H. Kohanpur and A.
Valocchi, J. Petrol. Sci. Eng., 155, 2133 (2017).
34) B. Gharedaghloo, S. J. Berg and E. A. Sudicky, Adv.
Water Resour., 143, 103681 (2020).
35) A. Viswanath, M. V. Manu, S. Savithri and U. T. S.
Pillai, J. Mater. Process. Tech., 244, 320330 (2017).
36) D. Silin and T. Patzek, Physica A, 371, 336360 (2006).
37) W. Hui, Y. S. Wang, D. Z. Ren and H. Jin, J. Petrol. Sci.
Eng., 192, 107295 (2020).
38) H. Nakae and H. Katoh, J. Jpn. I. Met. Mater., 63,
13561362 (1999).

PDF View

Effect of roughness on separation zone dimensions.

Experimental and numerical study of flow at a 90 degree lateral turnout with enhanced roughness coefficient and invert level changes

조도 계수 및 역전 수준 변화가 개선된 90도 측면 분출구에서의 유동에 대한 실험적 및 수치적 연구

Maryam Bagheri; Seyed M. Ali Zomorodian; Masih Zolghadr; H. Md. Azamathulla; C. Venkata Siva Rama Prasad

Abstract

측면 분기기(흡입구)의 상류 측에서 흐름 분리는 분기기 입구에서 와류를 일으키는 중요한 문제입니다. 이는 흐름의 유효 폭, 출력 용량 및 효율성을 감소시킵니다. 따라서 분리지대의 크기를 파악하고 크기를 줄이기 위한 방안을 제시하는 것이 필수적이다. 본 연구에서는 분리 구역의 치수를 줄이기 위한 방법으로 7가지 유형의 거칠기 요소를 분기구 입구에 설치하고 4가지 다른 배출(총 84번의 실험을 수행)과 함께 3개의 서로 다른 베드 반전 레벨을 조사했습니다. 또한 3D CFD(Computational Fluid Dynamics) 모델을 사용하여 분리 영역의 흐름 패턴과 치수를 평가했습니다. 결과는 거칠기 계수를 향상시키면 분리 영역 치수를 최대 38%까지 줄일 수 있는 반면, 드롭 구현 효과는 사용된 거칠기 계수를 기반으로 이 영역을 다르게 축소할 수 있음을 보여주었습니다. 두 가지 방법을 결합하면 분리 영역 치수를 최대 63%까지 줄일 수 있습니다.

Flow separation at the upstream side of lateral turnouts (intakes) is a critical issue causing eddy currents at the turnout entrance. It reduces the effective width of flow, turnout capacity and efficiency. Therefore, it is essential to identify the dimensions of the separation zone and propose remedies to reduce its dimensions. Installation of 7 types of roughening elements at the turnout entrance and 3 different bed invert levels, with 4 different discharges (making a total of 84 experiments) were examined in this study as a method to reduce the dimensions of the separation zone. Additionally, a 3-D Computational Fluid Dynamic (CFD) model was utilized to evaluate the flow pattern and dimensions of the separation zone. Results showed that enhancing the roughness coefficient can reduce the separation zone dimensions up to 38% while the drop implementation effect can scale down this area differently based on the roughness coefficient used. Combining both methods can reduce the separation zone dimensions up to 63%.

HIGHLIGHTS

Listen

Flow separation at the upstream side of lateral turnouts (intakes) is a critical issue causing eddy currents at the turnout entrance.
Installation of 7 types of roughening elements at the turnout entrance and 3 different bed level inverts were investigated.
Additionally, a 3-D Computational Fluid Dynamic (CFD) model was utilized to evaluate the flow.
Combining both methods can reduce the separation zone dimensions by up to 63%.

Experimental and numerical study of flow at a 90 degree lateral turnout with enhanced roughness coefficient and invert level changes

Keywords

discharge ratio, flow separation zone, intake, three dimensional simulation

INTRODUCTION

Listen

Turnouts or intakes are amongst the oldest and most widely used hydraulic structures in irrigation networks. Turnouts are also used in water distribution, transmission networks, power generation facilities, and waste water treatment plants etc. The flows that enter a turnout have a strong momentum in the direction of the main waterway and that is why flow separation occurs inside the turnout. The horizontal vortex formed in the separation area is a suitable place for accumulation and deposition of sediments. The separation zone is a vulnerable area for sedimentation and for reduction of effective flow due to a contracted flow region in the lateral channel. Sedimentaion in the entrance of the intake can gradually be transfered into the lateral channel and decrease the capacity of the higher order channels over time (Jalili et al. 2011). On the other hand, the existence of coarse-grained materials causes erosion and destruction of the waterway side walls and bottom. In addition, sedimentation creates conditions for vegetation to take root and damage the waterway cover, which causes water to leak from its perimeter. Therefore, it is important to investigate the pattern of the flow separation area in turnouts and provide solutions to reduce the dimensions of this area.

The three-dimensional flow structure at turnouts is quite complex. In an experimental study by Neary & Odgaard (1993) in a 90-degree water turnout it was found that the secondary currents and separation zone varies from the bed to the water surface. They also found that at a 90-degree water turnout, the bed roughness and discharge ratio play a critical role in flow structure. They asserted that an explanation of sediment behavior at a diversion entrance requires a comprehensive understanding of 3D flow patterns around the lateral-channel entrance. In addition, they suggested that there is a strong similarity between flow in a channel bend and a diversion channel, and that this similarity can rationalize the use of bend flow models for estimation of 3D flow structures in diversion channels.

Some of the distinctive characteristics of dividing flow in a turnout include a zone of separation immediately near the entrance of the lateral turnout (separation zone), a contracted flow region in the branch channel (contracted flow), and a stagnation point near the downstream corner of the junction (stagnation zone). In the region downstream of the junction, along the continuous far wall, separation due to flow expansion may occur (Ramamurthy et al. 2007), that is, a separation zone. This can both reduce the turnout efficiency and the effective width of flow while increasing the sediment deposition in the turnout entrance (Jalili et al. 2011). Installation of submerged vanes in the turnout entrance is a method which is already applied to reduce the size of flow separation zones. The separation zone draws sediments and floating materials into themselves. This reduces effective cross-section area and reduces transmission capacity. These results have also been obtained in past studies, including by Ramamurthy et al. (2007) and in Jalili et al. (2011). Submerged vanes (Iowa vanes) are designed in order to modify the near-bed flow pattern and bed-sediment motion in the transverse direction of the river. The vanes are installed vertically on the channel bed, at an angle of attack which is usually oriented at 10–25 degrees to the local primary flow direction. Vane height is typically 0.2–0.5 times the local water depth during design flow conditions and vane length is 2–3 times its height (Odgaard & Wang 1991). They are vortex-generating devices that generate secondary circulation, thereby redistributing sediment within the channel cross section. Several factors affect the flow separation zone such as the ratio of lateral turnout discharge to main channel discharge, angle of lateral channel with respect to the main channel flow direction and size of applied submerged vanes. Nakato et al. (1990) found that sediment management using submerged vanes in the turnout entrance to Station 3 of the Council Bluffs plant, located on the Missouri River, is applicable and efficient. The results show submerged vanes are an appropriate solution for reduction of sediment deposition in a turnout entrance. The flow was treated as 3D and tests results were obtained for the flow characteristics of dividing flows in a 90-degree sharp-edged, junction. The main and lateral channel were rectangular with the same dimensions (Ramamurthy et al., 2007).

Keshavarzi & Habibi (2005) carried out experiments on intake with angles of 45, 67, 79 and 90 degrees in different discharge ratios and reported the optimum angle for inlet flow with the lowest flow separation area to be about 55 degrees. The predicted flow characteristics were validated using experimental data. The results indicated that the width and length of the separation zone increases with the increase in the discharge ratio Qr (ratio of outflow per unit width in the turnout to inflow per unit width in the main channel).

Abbasi et al. (2004) performed experiments to investigate the dimensions of the flow separation zone at a lateral turnout entrance. They demonstrated that the length and width of the separation zone decreases with the increasing ratio of lateral turn-out discharge. They also found that with a reducing angle of lateral turnout, the length of the separation zone scales up and width of separation zone reduces. Then they compared their observations with results of Kasthuri & Pundarikanthan (1987) who conducted some experiments in an open-channel junction formed by channels of equal width and an angle of lateral 90 degree turnout, which showed the dimensions of the separation zone in their experiments to be smaller than in previous studies. Kasthuri & Pundarikanthan (1987) studied vortex and flow separation dimensions at the entrance of a 90 degree channel. Results showed that increasing the diversion discharge ratio can reduce the length and width of the vortex area. They also showed that the length and width of the vortex area remain constant at diversion ratios greater than 0.7. Karami Moghaddam & Keshavarzi (2007) analyzed the flow characteristics in turnouts with angles of 55 and 90 degrees. They reported that the dimensions of the separation zone decrease by increasing the discharge ratio and reducing the turnout angle with respect to the main channel. Studies about flow separation zone can be found in Jalili et al. (2011), Nikbin & Borghei (2011), Seyedian et al. (2008).

Jamshidi et al. (2016) measured the dimensions of a flow separation zone in the presence of submerged vanes with five arrangements (parallel, stagger, compound, piney and butterflies). Results showed that the ratio of the width to the length of the separation zone (shape index) was between 0.2 and 0.28 for all arrangements.

Karami et al. (2017) developed a 3D computational fluid dynamic (CFD) code which was calibrated by measured data. They used the model to evaluate flow pattern, diversion ratio of discharge, strength of the secondary flow, and dimensions of the vortex inside the channel in various dikes and submerged vane installation scenarios. Results showed that the diversion ratio of discharge in the diversion channel is dependent on the width of the flow separation area in the main channel. A dike, perpendicular to the flow, doubles the ratio of diverted discharge and reduces the suspended sediment load compared with the base-line situation by creating outer arch conditions. In addition, increasing the longitudinal distance between vanes increases the velocity gradient between the vanes and leads to a more severe erosion of the bed near the vanes.Figure 1VIEW LARGEDOWNLOAD SLIDE

Laboratory channel dimensions.

Al-Zubaidy & Hilo (2021) used the Navier–Stokes equation to study the flow of incompressible fluids. Using the CFD software ANSYS Fluent 19.2, 3D flow patterns were simulated at a diversion channel. Their results showed good agreement using the comparison between the experimental and numerical results when the k-omega turbulence viscous model was employed. Simulation of the flow pattern was then done at the lateral channel junction using a variety of geometry designs. These improvements included changing the intake’s inclination angle and chamfering and rounding the inner corner of the intake mouth instead of the sharp edge. Flow parameters at the diversion including velocity streamlines, bed shear stress, and separation zone dimensions were computed in their study. The findings demonstrated that changing the 90° lateral intake geometry can improve the flow pattern and bed shear stress at the intake junction. Consequently, sedimentation and erosion problems are reduced. According to the conclusions of their study, a branching angle of 30° to 45° is the best configuration for increasing branching channel discharge, lowering branching channel sediment concentration.

The review of the literature shows that most of the studies deal with turnout angle, discharge ratio and implementation of vanes as techniques to reduce the area of the separation zone. This study examines the effect of roughness coefficient and drop implementation at the entrance of a 90-degree lateral turnout on the dimensions of the separation zone. As far as the authors are aware, these two variables have never been studied as a remedy to decrease the separation zone dimensions whilst enhancing turnout efficiency. Additionally, a three-dimensional numerical model is applied to simulate the flow pattern around the turnout. The numerical results are verified against experimental data.

METHOD

Experimental setup

Listen

The experiments were conducted in a 90 degree dividing flow laboratory channel. The main channel is 15 m long, 0.5 m wide and 0.4 m high and the branch channel is 3 m long, 0.35 m wide and 0.4 m high, as shown in Figure 1. The tests were carried out at 9.65 m from the beginning of the flume and were far enough from the inlet, so we were sure that the flow was fully developed. According to Kirkgöz & Ardiçlioğlu (1997) the length of the developing region would be approximantly 65 and 72 times the flow depth. In this study, the depth is 9 cm, which makes this condition.

Both the main and lateral channel had a slope of 0.0003 with side walls of concrete. A 100 hp pump discharged the water into a stilling basin at the entrance of the main flume. The discharge was measured using an ultrasonic discharge meter around the discharge pipe. Eighty-four experiments in total were carried out at range of 0.1<Fr<0.4 (Froude numbers in main channel and upstream of turnout). The depth of water in the main channel in the experiments was 9 cm, in which case the effect of surface tension can be considered; according to research by Zolghadr & Shafai Bejestan (2020) and Zolghadr et al. (2021), when the water depth is more than 6 cm, the effect of surface tension is reduced and can be ignored given that the separation phenomenon occurs in the boundary layer, the height of the roughness creates disturbances in growth and development of the boundary layer and, as a result, separation growth is also faced with disruption and its dimensions grow less compared to smooth surfaces. Similar conditions occur in case of drop implementation. A disturbance occurs in the growth of the boundary layer and as a result the separation zone dimensions decrease. In order to investigate the effect of roughness coefficient and drop implementation on the separation zone dimensions, four different discharges (16, 18, 21, 23 l/s) in subcritical conditions, seven Manning (Strickler) roughness coefficients (0.009, 0.011, 0.017, 0.023, 0.028, 0.030, 0.032) as shown in Figure 2 and three invert elevation differences between the main channel and lateral turnout invert (0, 5 and 10 cm) at the entrance of the turnout were considered. The Manning roughness coefficient values were selected based on available and feasible values for real conditions, so that 0.009 is equivalent to galvanized sheet roughness and selected for the baseline tests. 0.011 is for concrete with neat surface, 0.017 and 0.023 are for unfinished and gunite concrete respectively. 0.030 and 0.032 values are for concrete on irregular excavated rock (Chow 1959). The roughness coefficients were created by gluing sediment particles on a thin galvanized sheet which was installed at the upstream side of the lateral turnout. The values of roughness coefficients were calculated based on the Manning-Strickler formula. For this purpose, some uniformly graded sediment samples were prepared and the Manning roughness coefficient of each sample was determined with respect to the median size (D₅₀) value pasted into the Manning-Strickler formula. Some KMnO₄ was sifted in the main channel upstream to visualize and measure the dimensions of the separation zone. Consequently, when KMnO₄ approached the lateral turnout a photo of the separation zone was taken from a top view. All the experiments were recorded and several photos were taken during the experiment after stablishment of steady flow conditions. The photos were then imported to AutoCAD to measure the separation zone dimensions. Because all the shooting was done with a high-definition camera and it was possible to zoom in, the results are very accurate.Figure 2 VIEW LARGEDOWNLOAD SLIDE

Roughness plates.

The velocity values were also recorded by a one-dimensional velocity meter at 15 cm distance from the turnout entrance and in transverse direction (perpendicular to the flow direction).

The water level was also measured by depth gauges with a accuracy of 0.1 mm, and velocity in one direction with a single-dimensional KENEK LP 1100 with an accuracy of ±0.02 m/s (0–1 m/s), ± 0.04 m/s (1–2 m/s), ± 0.08 m/s (2–4 m/s), ±0.10 m/s (4–5 m/s).

Numerical simulation

ListenA FLOW-3D numerical model was utilized as a solver of the Navier-Stokes equation to simulate the three-dimensional flow field at the entrance of the turnout. The governing equations included continuity momentum equations. The continuity equation, regardless of the density of the fluid in the form of Cartesian coordinates x, y, and z, is as follows:

(1)where u, v, and w represent the velocity components in the x, y, and z directions, respectively; A_x, A_y, and A_z are the surface flow fractions in the x, y, and z directions, respectively; V_F denotes flow volume fraction; r is the density of the fluid; t is time; and R_sor refers to the source of the mass. Equations (2)–(4) show momentum equations in x, y and z dimensions respectively :

(2)

(3)

(4)where G_x, G_y, and G_z are the accelerations caused by gravity in the x, y, and z directions, respectively; and f_x, f_y, and f_z are the accelerations caused by viscosity in the x, y, and z directions, respectively.

The turbulence models used in this study were the renormalized group (RNG) models. Evaluation of the concordance of the mentioned models with experimental studies showed that the RNG model provides more accurate results.

Two blocks of mesh were used to simulate the main channels and lateral turnout. The meshes were denser in the vicinity of the entrance of the turnout in order to increase the accuracy of computations. Boundary conditions for the main mesh block included inflow for the channel entrance (volumetric flow rate), outflow for the channel exit, ‘wall’ for the bed and the right boundary and ‘symmetry’ for the top (free surface) and left boundaries (turnout). The side wall roughness coefficient was given to the software as the Manning number in surface roughness of any component. Considering the restrictions in the available processor, a main mesh block with appropriate mesh size was defined to simulate the main flow field in the channel, while the nested mesh-block technique was utilized to create a very dense solution field near the roughness plate in order to provide accurate results around the plates and near the entrance of the lateral turnout. This technique reduced the number of required mesh elements by up to 60% in comparison with the method in which the mesh size of the main solution field was decreased to the required extent.

The numerical outputs are verified against experimental data. The hydraulic characteristics of the experiment are shown in Table 1.Table 1

Hydraulic conditions of the flow

Q(L/s)	Fr	Y₁ (m)	Q₂/Q₁
16	0.449	0.09	0.22
18	0.335	0.09	0.61
21	0.242	0.09	0.71
23	0.180	0.09	1.04

RESULTS AND DISCUSSION

Experimental results

Listen

During the experiments, the dimensions of the separation zone were recorded with an HD camera. Some photos were imported to AutoCad software. Then, the separation zones dimensions were measured and compared in different scenarios.

At the beginning, the flow pattern in the separation zone for four different hydraulic conditions was studied for seven different Manning roughness coefficients from 0.009 to 0.032. To compare the obtained results, roughness of 0.009 was considered as the base line. The percentage of reduction in separation zone area in different roughness coefficients is shown in Figure 3. According to this figure, by increasing the roughness of the turnout side wall, the separation zone area ratio reduces (ratio of separation zone area to turnout area). In other words, in any desired Froud number, the highest dimensions of the separation zone area are related to the lowest roughness coefficients. In Figure 3, ‘A’ is the area of the separation zone and ‘A_i’ represents the total area of the turnout.Figure 3VIEW LARGEDOWNLOAD SLIDE

Effect of roughness on separation zone dimensions.Figure 4 VIEW LARGEDOWNLOAD SLIDE

Effect of roughness on separation zone dimensions.

It should be mentioned that the separation zone dimensions change with depth, so that the area is larger at the surface than near the bed. This study measured the dimensions of this area at the surface. Figure 4 show exactly where the roughness elements were located.Figure 5 VIEW LARGEDOWNLOAD SLIDE

Comparison of separation zone for n=0.023 and n=0.032.

Figure 5 shows images of the separation zone at n=0.023 and n=0.032 as examples, and show that the separation area at n=0.032 is smaller than that of n=0.023.

The difference between the effect of the two 0.032 and 0.030 roughnesses is minor. In other words, the dimensions of the separation zone decreased by increasing roughness up to 0.030 and then remained with negligable changes.

In the next step, the effect of intake invert relative to the main stream (drop) on the dimensions of the separation zone was investigated. To do this, three different invert levels were considered: (1) without drop; (2) a 5 cm drop between the main canal and intake canal; and (3) a 10 cm drop between the main canal and intake canal. The without drop mode was considered as the control state. Figure 6 shows the effect of drop implementation on separation zone dimensions. Tables 2 and 3 show the reduced percentage of separation zone areas in 5 and 10 cm drop compared to no drop conditions as the base line. It was found that the best results were obtained when a 10 cm drop was implemented.Table 2

Decrease percentage of separation zone area in 5 cm drop

Fr	n=0.011	n=0.017	n=0.023	n=0.028	n=0.030	n=0.032
0.08	10.56	11.06	25.27	33.03	35.57	36.5
0.121	7.66	11.14	11.88	15.93	34.59	36.25
0.353	1.38	2.63	8.17	14.39	31.20	31.29
0.362	3	11.54	19.56	25.73	37.89	38.31

Table 3

Decrease percentage of separation zone area in 10 cm drop

Fr	n=0.011	n=0.017	n=0.023	n=0.028	n=0.030	n=0.032
0.047	4.30	8.75	23.47	31.22	34.96	35.13
0.119	11.01	13.16	15.02	21.48	39.45	40.68
0.348	3.89	5.71	9.82	16.09	29	30.96
0.354	2.84	10.44	18.42	25.45	35.68	35.76

Figure 6 VIEW LARGEDOWNLOAD SLIDE

Effect of drop implementation on separation zone dimensions.

The combined effect of drop and roughness is shown in Figure 7. According to this figure, by installing a drop structure at the entrance of the intake, the dimensions of the separation zone scales down in any desired roughness coefficient. Results indicated that by increasing the roughness coefficient or drop implementation individually, the separation zone area decreases up to 38 and 25% respectively. However, employing both techniques simultaneously can reduce the separation zone area up to 63% (Table 4). The reason for the reduction of the dimensions of the separation zone area by drop implementation can be attributed to the increase of discharge ratio. This reduces the dimensions of the separation zone area.Table 4

Reduction in percentage of combined effect of roughness and 10 cm drop

Qi	n=0.011	n=0.017	n=0.023	n=0.028	n=0.030	n=0.032
16	32.3	35.07	37.2	45.7	58.01	59.1
18	44.5	34.15	36.18	48.13	54.2	56.18
21	43.18	32.33	42.30	37.79	57.16	63.2
23	40.56	34.5	34.09	46.25	50.12	57.2

Figure 7VIEW LARGEDOWNLOAD SLIDE

Combined effect of roughness and drop on separation zone dimensions.

This method increases the discharge ratio (ratio of turnout to main channel discharge). The results are compatible with the literature. Some other researchers reported that increasing the discharge ratio can scale down the separation zone dimensions (Karami Moghaddam & Keshavarzi 2007; Ramamurthy et al. 2007). However, these researchers employed other methods to enhance the discharge ratio. Drop implementation is simple and applicable in practice, since there is normally an elevation difference between the main and lateral canal in irrigation networks to ensure gravity flow occurance.

Table 4 depicts the decrease in percentage of the separation zone compared to base line conditions in different arrangements of the combined tests.Figure 8VIEW LARGEDOWNLOAD SLIDE

Velocity profiles for various roughness coefficients along turnout width.

A comparison between the proposed methods introduced in this paper and traditional methods such as installation of submerged vanes, and changing the inlet geometry (angle, radius) was performed. Figure 8 shows the comparison of the results. The comparison shows that the new techniques can be highly influential and still practical. In this research, with no change in structural geometry (enhancement of roughness coefficient) or minor changes with respect to drop implementation, the dimensions of the separation zone are decreased noticeably. The velocity values were also recorded by a one-dimensional velocity meter at 15 cm distance from the turnout entrance and in a transverse direction (perpendicular to the flow direction). The results are shown in Figure 9.Figure 9VIEW LARGEDOWNLOAD SLIDE

Effect of roughness on separation zone dimensions in numerical study.

Numerical results

Listen

This study examined the flow patterns around the entrance of a diversion channel due to various wall roughnesses in the diversion channel. Results indicated that increasing the discharge ratio in the main channel and diversion channel reduces the area of the separation zone in the diversion channel.Figure 10 VIEW LARGEDOWNLOAD SLIDE

Comparision of the vortex area (software output) for three roughnesses (0.009, 0.023 and 0.032).A laboratory and numerical error rate of 0.2605 was calculated from the following formula,

where U_exp is the experimental result, Unum is the numerical result, and N is the number of data.

Figure 9 shows the effect of roughness on separation zone dimensions in numerical study. Figure 10 compares the vortex area (software output) for three roughnesses, 0.009, 0.023 and 0.032 and Figure 11 shows the flow lines (tecplot output) that indicate the effect of roughness on flow in the separation zone. Numerical analysis shows that by increasing the roughness coefficient, the dimensions of the separation zone area decrease, as shown in Figure 10 where the separation zone area at n=0.032 is less than the separation zone area at n=0.009.Figure 11 VIEW LARGEDOWNLOAD SLIDE

Comparison of vortex area in 3D mode (tecplot output) with two roughnesses (a) 0.009 and (b) 0.032.Figure 12 VIEW LARGEDOWNLOAD SLIDE

Velocity vector for flow condition Q1/422 l/s, near surface.

The velocities intensified moving midway toward the turnout showing that the effective area is scaled down. The velocity values were almost equal to zero near the side walls as expected. As shown in Figure 12 the approach vortex area velocity decreases. Experimental and numerical measured velocity at x=0.15 m of the diversion channel compared in Figure 13 shows that away from the separation zone area, the velocity increases. All longitudinal velocity contours near the vortex area are distinctly different between different roughnesses. The separation zone is larger at less roughness both in length and width.Figure 13 VIEW LARGEDOWNLOAD SLIDE

Exprimental and numerical measured velocity.

CONCLUSION

Listen

This study introduces practical and feasible methods for enhancing turnout efficiency by reducing the separation zone dimensions. Increasing the roughness coefficient and implementation of inlet drop were considered as remedies for reduction of separation zone dimensions. A data set has been compiled that fully describes the complex, 3D flow conditions present in a 90 degree turnout channel for selected flow conditions. The aim of this numerical model was to compare the results of a laboratory model in the area of the separation zone and velocity. Results showed that enhancing roughness coefficient reduce the separation zone dimensions up to 38% while the drop implementation effect can scale down this area differently based on roughness coefficient used. Combining both methods can reduce the separation zone dimensions up to 63%. Further research is proposed to investigate the effect of roughness and drop implementation on sedimentation pattern at lateral turnouts. The dimensions of the separation zone decreases with the increase of the non-dimensional parameter, due to the reduction ratio of turnout discharge increasing in all the experiments.

This method increases the discharge ratio (ratio of turnout to main channel discharge). The results are compatible with the literature. Other researchers have reported that intensifying the discharge ratio can scale down the separation zone dimensions (Karami Moghaddam & Keshavarzi 2007; Ramamurthy et al. 2007). However, they employed other methods to enhance the discharge ratio. Employing both techniques simultaneously can decrease the separation zone dimensions up to 63%. A comparison between the new methods introduced in this paper and traditional methods such as installation of submerged vanes, and changing the inlet geometry (angle, radius) was performed. The comparison shows that the new techniques can be highly influential and still practical. The numerical and laboratory models are in good agreement and show that the method used in this study has been effective in reducing the separation area. This method is simple, economical and can prevent sediment deposition in the intake canal. Results show that CFD prediction of the fluid through the separation zone at the canal intake can be predicted reasonably well and the RNG model offers the best results in terms of predictability.

DATA AVAILABILITY STATEMENT

Listen

All relevant data are included in the paper or its Supplementary Information.

REFERENCES

Abbasi A., Ghodsian M., Habibi M. & Salehi Neishabouri S. A. 2004 Experimental investigation on dimensions of flow separation zone at lateral intakeentrance. Research & Construction; Pajouhesh va Sazandegi 62, 38–44. (In Persian).Google Scholar Al-Zubaidy R. & Hilo A. 2021 Numerical investigation of flow behavior at the lateral intake using Computational Fluid Dynamics (CFD). Materials Today: Proceedings. https://doi.org/10.1016/j.matpr.2021.11.172.Google Scholar Chow V. T. 1959 Open Channel Hydraulics. McGraw-Hill, New York.Jalili H., Hosseinzadeh Dalir A. & Farsadizadeh D. 2011 Effect of intake geometry on the sediment transport and lateral flow pattern. Iranian Water Research Journal 5 (9), 1–10. (In Persian).Google Scholar Jamshidi A., Farsadizadeh D. & Hosseinzadeh Dalir A. 2016 Variations of flow separation zone at lateral intake entrance using submerged vanes. Journal of Civil Engineering Urban 6 (3), 54–63. Journal homepage. Available from: www.ojceu.ir/main.Google Scholar Karami Moghaddam K. & Keshavarzi A. 2007 Investigation of flow structure in lateral intakes of 55° and 90° with rounded entrance edge. In: 03 National Congress on Civil Engineering University of Tabriz. Available from: https://civilica.com/doc/16317. (In Persian).Google Scholar Karami H., Farzin S., Sadrabadi M. T. & Moazeni H. 2017 Simulation of flow pattern at rectangular lateral intake with different dike and submerged vane scenarios. Journal of Water Science and Engineering 10 (3), 246–255. https://doi.org/10.1016/j.wse.2017.10.001.Google Scholar Crossref Kasthuri B. & Pundarikanthan N. V. 1987 Discussion on separation zone at open- channel junction. Journal of Hydraulic Engineering 113 (4), 543–548.Google Scholar Crossref Keshavarzi A. & Habibi L. 2005 Optimizing water intake angle by flow separation analysis. Journal of Irrigation and Drain 54, 543–552. https://doi.org/10.1002/ird.207.Google Scholar Crossref Kirkgöz M. S. & Ardiçlioğlu M. 1997 Velocity profiles of developing and developed open channel flow. Journal of Hydraulic Engineering 1099–1105. 10.1061/(ASCE)0733-9429(1997)123:12(1099).Google Scholar Nakato T., Kennedy J. F. & Bauerly D. 1990 Pumpstation intake-shoaling control with submerge vanes. Journal of Hydraulic Engineering. https://doi.org/10.1061/(ASCE)0733-9429(1990)116:1(119).Google Scholar Neary V. S. & Odgaard J. A. 1993 Three-dimensional flow structure at open channel diversions. Journal of Hydraulic Engineering. ASCE 119 (11), 1224–1230. https://doi.org/10.1061/(ASCE)0733-9429(1993)119:11(1223).Google Scholar Crossref Nikbin S. & Borghei S. M. 2011 Experimental investigation of submerged vanes effect on dimensions of flow separation zone at a 90° openchannel junction. In: 06rd National Congress on Civil Engineering University of Semnan. (In Persian). Available from: https://civilica.com/doc/120494.Google Scholar Odgaard J. A. & Wang Y. 1991 Sediment management with submerged vanes, I: theory. Journal of Hydraulic Engineering 117 (3), 267–283.Google Scholar Crossref Ramamurthy A. S., Junying Q. & Diep V. 2007 Numerical and experimental study of dividing open-channel flows. Journal of Hydraulic Engineering. See: https://doi.org/10.1061/(ASCE)0733-9429(2007)133:10(1135).Google Scholar Seyedian S., Karami Moghaddam K. & Shafai Begestan M. 2008 Determining the optimal radius in lateral intakes of 55° and 90° using variation of flow velocity. In: 07th Iranian Hydraulic Conference. Power & Water University of Technology (PWUT). (In Persian). Available from: https://civilica.com/doc/56251.Google Scholar Zolghadr M. & Shafai Bejestan M. 2020 Six legged concrete (SLC) elements as scour countermeasures at wing wall bridge abutments. International Journal of River Basin Management. doi: 10.1080/15715124.2020.1726357.Google Scholar Zolghadr M., Zomorodian S. M. A., Shabani R. & Azamatulla H.Md. 2021 Migration of sand mining pit in rivers: an experimental, numerical and case study. Measurement. https://doi.org/10.1016/j.measurement.2020.108944.Google Scholar © 2022 The AuthorsThis is an Open Access article distributed under the terms of the Creative Commons Attribution Licence (CC BY-NC-ND 4.0), which permits copying and redistribution for non-commercial purposes with no derivatives, provided the original work is properly cited (http://creativecommons.org/licenses/by-nc-nd/4.0/).

PDF View

Tag: Particle

Abstract

Similar content being viewed by others

References

Acknowledgments

Author information

Authors and Affiliations

Keywords

수직 수중 펄스 제트에 의한 모래층 정련에 대한 펄스 폭과 진폭의 영향 조사

Highlights

Abstract

Introduction

Section snippets

Model and calculation settings

The effects of the pulse width on submerged jet scouring

conclusions

CRediT authorship contribution statement

Declaration of competing interest

References (44)

해저 산사태 쓰나미의 최대 초기 파동 진폭 추정: 3차원 모델링 접근법

Highlights

Abstract

Keywords

1. Introduction and literature review

2. Data and methods

2.1. Physical experiments

2.2. Numerical simulations applying FLOW-3D hydro

2.3. Validation

2.4. The dataset

2.5. Landslide velocity

2.6. Effect of air entrainment

3. Results

3.1. Wave generation and propagation

3.2. Influence of landslide parameters on tsunami amplitude

3.3. Predictive equation

4. Conclusions

CRediT authorship contribution statement

Declaration of competing interest

Funding

Acknowledgements

Data availability

References

초록

주제어

키워드

출판물

저자 소속기관

Abstract

Keywords

DOI

References

Abstract

바인더 제트 3D 프린팅 중 계면 유체-입자 상호 작용에 대한 CFD-DEM 결합 시뮬레이션

Abstract

Introduction

Section snippets

Mathematical description of interfacial fluid–particle interaction

CFD solver for incompressible flow with multifluid interfaces

DEM solver for solid particle dynamics

Unified CFD-DEM solver

Binder jet process modeling and validation experiments

Conclusions

CRediT authorship contribution statement

Declaration of competing interest

Acknowledgments

References (155)

몰리브덴 분말층 융합-레이저 빔의 용융 풀 형태의 준안정성에 대한 분말 크기 및 공정 매개변수의 영향

Abstract

References

프로필 오목부가 탁도 퇴적물에 미치는 영향: 전 세계 대륙 경계에 대한 해저 협곡의 통찰력

Highlights

Abstract

Introduction

Section snippets

Submarine canyons used in this study

Concavity of longitudinal canyon profiles

Validation of the hypothesis

Conclusion

CRediT authorship contribution statement

Declaration of competing interest