Pamukkale University Journal of Engineering Sciences, 1997
The effects of deformation temperature and strain rate to the mechanical properties of Aluminum (... more The effects of deformation temperature and strain rate to the mechanical properties of Aluminum (Al 99.0) were investigated by tensile experiment at different deformation temperatures and strain rate. At the end of investigation; it was determined that, with increasing deformation temperature, yield and tensile strenghts of the material decrease, strain rate and decrease of area increase, when plastic deformation exponent (n) decreases, strain rate accuracy exponent (m) increases. At a fixed temperature an increase in deformation speed increased all mechanical properties.
ÖZET Toz metalden üretilen makine parçaları küçük hacimli olduklarından tek bir makine parçası ol... more ÖZET Toz metalden üretilen makine parçaları küçük hacimli olduklarından tek bir makine parçası olarak kullanılır ve birleştirmek veya onarmak için kaynak işlemine gerek duyulmaz. Ancak kullanım alanlarının yaygınlaşması toz metal parçaların boyutlarını da arttırmıştır. Son zamanlarda toz metal parçaların kaynakla birleştirme tekniği üzerinde çalışmalar yoğunlaşmaktadır. Bu çalışmada demir esaslı sinterlenmiş toz metal numuneler elektrik ark kaynağı, MAG ve TIG kaynak yöntemleri ile birleştirilmiştir. Numunelerin kaynak bölgesindeki sertlik dağılımı ve iç yapı değişimleri incelenmiştir. Anahtar kelimeler: Toz Metal, Kaynak. 1. GİRİŞ Malzeme üretimindeki gelişmeler farklı uygulama alanları için farklı malzemeler geliştirilmesini [1] gerektirmiştir. Bu farklı özellikteki malzemelerden birisi de toz metalurjisi (TM) ile üretilen makine parçalarıdır. TM ile üretim yöntemi, istenilen kimyasal kompozisyonu verecek şekilde karıştırılmış metal tozlarının oda sıcaklığında, üretilecek parça şe...
As known, 2XXX and 7XXX Aluminium wrought alloys can have high strength values by means of precip... more As known, 2XXX and 7XXX Aluminium wrought alloys can have high strength values by means of precipitation hardening heat treatment. Determination of the precipitation hardening conditions, which can give the most suitable strength values of an alloy, requires numerous tests. But the results of this process which require long time and high cost can be obtained in a shorter time and at a lower cost with less data by means of Artificial Neural Networks method. Since this method is used, less number of experiments and therefore less data are needed. Then other values are found by means of Artificial Neural Networks (ANN) method. This paper, presents the feed forward ANN to determine hardness of alloy for different temperatures. For this purpose, a classic Back-Propagation Algorithm was used that is structure as 1:2:4.
Kaymali yatak malzemesi olarak bakir esasli alasimlardan pirinc ve ozellikle bronz yaygin bir sek... more Kaymali yatak malzemesi olarak bakir esasli alasimlardan pirinc ve ozellikle bronz yaygin bir sekilde kullanilmaktadir. Bu alasimlar kaymali yataklardan beklenen ozellikleri saglamaktadirlar. Iyi bir tribolojik performansa sahip bu malzemeler, kaymali yataklarda iyi sonuclar vermektedir. Bu calismada; CuSn10 bronzu ile CuZn30 pirincinden uretilen kaymali yataklarin surtunme ve asinma ozellikleri belirlenip, birbiriyle karsilastirilmistir. Karsi asindirici olarak SAE 1050 celik mil kullanilmistir. Deneyler radyal kaymali yatak asinma test cihazinda 20 N yuk, 1500 d/dak ve 2.5 saatte yapilmistir. Sonuc olarak, kuru ortamda yapilan deneylerde yuksek surtunme katsayisi ve agirlik kaybi, yagli ortamda ise cok daha dusuk elde edilmistir.
Plastik malzeme turleri gunden gune artmakta ve bu malzemelerden farkli ozellikler elde etmek ici... more Plastik malzeme turleri gunden gune artmakta ve bu malzemelerden farkli ozellikler elde etmek icin kompozitleri uretilmektedir. Kullanimi yaygin bir plastik turu olan polyestere, asinma dayanimini arttirmak uzere farkli agirlik oranlarinda Al2O3 partikulleri takviye edilerek plastik matriksli partikul takviyeli kompozit malzemeler uretilmistir. Uretilen kompozit malzemeler Pim-Disk modeli bir asinma deney duzeneginde ayni tribolojik sartlarda asinma deneyine tabi tutulmustur. Ayni tribolojik sartlar altinda asinma deneyleri yapilan Polyester-Al2O3 kompozitlerinin asinma dayanimlarinin, polyester icindeki Al2O3 oraninin artisiyla yukseldigi belirlenmistir. Asinma dayanimi ile sertlik arasinda bir iliski belirlenememistir.
Kaymal yatak malzemesi olarak bak r esasl ala mlardan bronzlar yayg n bir ekilde kullan lmaktad r... more Kaymal yatak malzemesi olarak bak r esasl ala mlardan bronzlar yayg n bir ekilde kullan lmaktad r. Bu ala mlar kaymal yataklardan beklenen ozellikleri sa lamaktad rlar. yi bir tribolojik ozelli e sahip bu malzemeler, kaymal yataklarda iyi sonuclar vermektedir. Bu cal mada; CuSn10 bronzundan uretilen kaymalyataklar n farkl yuk ve h zlarda kuru ve ya l ortamlardaki surtunme ve a nma ozellikleri incelenmi ve kar la t r lm t r. Kar a nd r c olarak SAE 1050 celik mil kullan lm t r. Deneyler radyal kaymal yatak a nma test cihaz nda 10 N ve 20 N yukleme ve 750 d/dak ve 1500 d/dak da kuru ve ya l ortamda toplam 2.5 saatte yap lm t r. Sonuc olarak, kuru ortamda yap lan deneylerde yuksek, ya l ortamda ise cok daha du uk surtunme katsay s ve a nma kayb gorulmu tur
Abstract Mechanical and microstructural properties of quenched steel are directly related to temp... more Abstract Mechanical and microstructural properties of quenched steel are directly related to tempering time and temperature. In many applications, conventionally quenched and tempered steel is widely used for acquiring high strength and toughness. The present study was carried out to investigate the variation in mechanical properties, observation of diminished energy consumption and evaluation of the microstructural properties in SAE-AISI 6150 steel components by induction heating, compared with those of steel tempered by conventional method. Induction quenched and tempered steel provides a shorter process time, less energy consumption and improved mechanical properties through the inhibition of grain growth. In this study, quenching and tempering processes were carried out on medium and low frequency induction units and by using a conventional electrical resistance furnace for the sake of comparison. It was observed that cementite particles began changing their shape from spherical to fine-grained in the induction tempered samples. The sample tempered by low frequency induction manifests superior mechanical properties and offers a potential advantage for significant cost savings.
Brass and especially bronze in copper based alloys are widely used as journal bearing material. P... more Brass and especially bronze in copper based alloys are widely used as journal bearing material. Pure copper materials are not used as journal bearing material due to their low mechanical and hardness properties. These materials having acceptable tribological and mechanical performance give satisfactory results in journal bearings. In this study, tribological and mechanical properties of journal bearings manufactured from copper based CuSn10 bronze and CuZn30 brass were investigated. Moreover, the effect of alloy elements of Cu, Sn and Zn on tribological and mechanical properties of journal bearings was evaluated. SAE 1050 steel shaft (journal) was used as counter abrader. Wear experiments were carried out at 20N loads, 1500rpm for 2.5h by using radial journal bearing wear test rig.
ÖZET Kaymalı yatak malzemesi olarak kalay-kurşun esaslı alaşımlar otomotiv endüstrisinde yaygın b... more ÖZET Kaymalı yatak malzemesi olarak kalay-kurşun esaslı alaşımlar otomotiv endüstrisinde yaygın bir şekilde kullanılmaktadır. Bu malzemelerin esasını oluşturan saf kalay ve kurşun ise iyi kayma özelliği olmasına rağmen çok düşük sertliğe sahip olduğundan düşük aşınma dayanımı göstermekte ve düşük mekanik özellikleri nedeniyle tek başına yatak malzemesi olarak kullanılmamaktadır. İyi bir kayma özelliğine sahip bu malzemelerin içerisine Al, Zn gibi elementler ilave edildiğinde kaymalı yataklarda iyi sonuçlar vermektedir. Bu çalışmada; kalay kurşun esaslı SnPbAlZn alaşımı ve bu malzemelerin esasını oluşturan saf Sn, saf Pb ve alaşım elementlerinden saf Al ve saf Zn dan üretilen kaymalı yatakların sürtünme ve aşınma özellikleri belirlenip, birbiriyle karşılaştırılmıştır. Karşı aşındırıcı olarak SAE 1050 çelik mil kullanılmıştır. Deneyler radyal kaymalı yatak aşınma deney cihazında 20 N yük, 1500 d/dak ve 2.5 saatte yapılmıştır. Sonuç olarak, SnPbAlZn malzemesi, saf durumda üretilen numu...
PurposeThis paper aims to determine the usage time of the test lubricant N0, prepared from base o... more PurposeThis paper aims to determine the usage time of the test lubricant N0, prepared from base oils of Aliaga Plant, Izmir, in gasoline and diesel‐engines, and the investigations of high‐temperature oxidation, engine‐protective properties, and property changes of the lubricant in performance time.Design/methodology/approachPhysical and chemical properties of the lubricating oil were initially established, and the oil was then subjected to Petter W‐1 gasoline and Petter AV‐1 diesel test engines. Dismantling of the engine parts was followed by the examination of pistons, piston rings and bearings, and analysis of the lubricant was also undertaken. The engine performance test results and the quality control of the lubricating oil assessments were evaluated according to the International Engine Lubricant Specifications.FindingsThe lubricating oil, under sluggish experimental conditions, appears to meet a 40‐hour test in gasoline engines and a 120‐hour test in diesel engines with the sp...
Pamukkale University Journal of Engineering Sciences, 1997
The effects of deformation temperature and strain rate to the mechanical properties of Aluminum (... more The effects of deformation temperature and strain rate to the mechanical properties of Aluminum (Al 99.0) were investigated by tensile experiment at different deformation temperatures and strain rate. At the end of investigation; it was determined that, with increasing deformation temperature, yield and tensile strenghts of the material decrease, strain rate and decrease of area increase, when plastic deformation exponent (n) decreases, strain rate accuracy exponent (m) increases. At a fixed temperature an increase in deformation speed increased all mechanical properties.
ÖZET Toz metalden üretilen makine parçaları küçük hacimli olduklarından tek bir makine parçası ol... more ÖZET Toz metalden üretilen makine parçaları küçük hacimli olduklarından tek bir makine parçası olarak kullanılır ve birleştirmek veya onarmak için kaynak işlemine gerek duyulmaz. Ancak kullanım alanlarının yaygınlaşması toz metal parçaların boyutlarını da arttırmıştır. Son zamanlarda toz metal parçaların kaynakla birleştirme tekniği üzerinde çalışmalar yoğunlaşmaktadır. Bu çalışmada demir esaslı sinterlenmiş toz metal numuneler elektrik ark kaynağı, MAG ve TIG kaynak yöntemleri ile birleştirilmiştir. Numunelerin kaynak bölgesindeki sertlik dağılımı ve iç yapı değişimleri incelenmiştir. Anahtar kelimeler: Toz Metal, Kaynak. 1. GİRİŞ Malzeme üretimindeki gelişmeler farklı uygulama alanları için farklı malzemeler geliştirilmesini [1] gerektirmiştir. Bu farklı özellikteki malzemelerden birisi de toz metalurjisi (TM) ile üretilen makine parçalarıdır. TM ile üretim yöntemi, istenilen kimyasal kompozisyonu verecek şekilde karıştırılmış metal tozlarının oda sıcaklığında, üretilecek parça şe...
As known, 2XXX and 7XXX Aluminium wrought alloys can have high strength values by means of precip... more As known, 2XXX and 7XXX Aluminium wrought alloys can have high strength values by means of precipitation hardening heat treatment. Determination of the precipitation hardening conditions, which can give the most suitable strength values of an alloy, requires numerous tests. But the results of this process which require long time and high cost can be obtained in a shorter time and at a lower cost with less data by means of Artificial Neural Networks method. Since this method is used, less number of experiments and therefore less data are needed. Then other values are found by means of Artificial Neural Networks (ANN) method. This paper, presents the feed forward ANN to determine hardness of alloy for different temperatures. For this purpose, a classic Back-Propagation Algorithm was used that is structure as 1:2:4.
Kaymali yatak malzemesi olarak bakir esasli alasimlardan pirinc ve ozellikle bronz yaygin bir sek... more Kaymali yatak malzemesi olarak bakir esasli alasimlardan pirinc ve ozellikle bronz yaygin bir sekilde kullanilmaktadir. Bu alasimlar kaymali yataklardan beklenen ozellikleri saglamaktadirlar. Iyi bir tribolojik performansa sahip bu malzemeler, kaymali yataklarda iyi sonuclar vermektedir. Bu calismada; CuSn10 bronzu ile CuZn30 pirincinden uretilen kaymali yataklarin surtunme ve asinma ozellikleri belirlenip, birbiriyle karsilastirilmistir. Karsi asindirici olarak SAE 1050 celik mil kullanilmistir. Deneyler radyal kaymali yatak asinma test cihazinda 20 N yuk, 1500 d/dak ve 2.5 saatte yapilmistir. Sonuc olarak, kuru ortamda yapilan deneylerde yuksek surtunme katsayisi ve agirlik kaybi, yagli ortamda ise cok daha dusuk elde edilmistir.
Plastik malzeme turleri gunden gune artmakta ve bu malzemelerden farkli ozellikler elde etmek ici... more Plastik malzeme turleri gunden gune artmakta ve bu malzemelerden farkli ozellikler elde etmek icin kompozitleri uretilmektedir. Kullanimi yaygin bir plastik turu olan polyestere, asinma dayanimini arttirmak uzere farkli agirlik oranlarinda Al2O3 partikulleri takviye edilerek plastik matriksli partikul takviyeli kompozit malzemeler uretilmistir. Uretilen kompozit malzemeler Pim-Disk modeli bir asinma deney duzeneginde ayni tribolojik sartlarda asinma deneyine tabi tutulmustur. Ayni tribolojik sartlar altinda asinma deneyleri yapilan Polyester-Al2O3 kompozitlerinin asinma dayanimlarinin, polyester icindeki Al2O3 oraninin artisiyla yukseldigi belirlenmistir. Asinma dayanimi ile sertlik arasinda bir iliski belirlenememistir.
Kaymal yatak malzemesi olarak bak r esasl ala mlardan bronzlar yayg n bir ekilde kullan lmaktad r... more Kaymal yatak malzemesi olarak bak r esasl ala mlardan bronzlar yayg n bir ekilde kullan lmaktad r. Bu ala mlar kaymal yataklardan beklenen ozellikleri sa lamaktad rlar. yi bir tribolojik ozelli e sahip bu malzemeler, kaymal yataklarda iyi sonuclar vermektedir. Bu cal mada; CuSn10 bronzundan uretilen kaymalyataklar n farkl yuk ve h zlarda kuru ve ya l ortamlardaki surtunme ve a nma ozellikleri incelenmi ve kar la t r lm t r. Kar a nd r c olarak SAE 1050 celik mil kullan lm t r. Deneyler radyal kaymal yatak a nma test cihaz nda 10 N ve 20 N yukleme ve 750 d/dak ve 1500 d/dak da kuru ve ya l ortamda toplam 2.5 saatte yap lm t r. Sonuc olarak, kuru ortamda yap lan deneylerde yuksek, ya l ortamda ise cok daha du uk surtunme katsay s ve a nma kayb gorulmu tur
Abstract Mechanical and microstructural properties of quenched steel are directly related to temp... more Abstract Mechanical and microstructural properties of quenched steel are directly related to tempering time and temperature. In many applications, conventionally quenched and tempered steel is widely used for acquiring high strength and toughness. The present study was carried out to investigate the variation in mechanical properties, observation of diminished energy consumption and evaluation of the microstructural properties in SAE-AISI 6150 steel components by induction heating, compared with those of steel tempered by conventional method. Induction quenched and tempered steel provides a shorter process time, less energy consumption and improved mechanical properties through the inhibition of grain growth. In this study, quenching and tempering processes were carried out on medium and low frequency induction units and by using a conventional electrical resistance furnace for the sake of comparison. It was observed that cementite particles began changing their shape from spherical to fine-grained in the induction tempered samples. The sample tempered by low frequency induction manifests superior mechanical properties and offers a potential advantage for significant cost savings.
Brass and especially bronze in copper based alloys are widely used as journal bearing material. P... more Brass and especially bronze in copper based alloys are widely used as journal bearing material. Pure copper materials are not used as journal bearing material due to their low mechanical and hardness properties. These materials having acceptable tribological and mechanical performance give satisfactory results in journal bearings. In this study, tribological and mechanical properties of journal bearings manufactured from copper based CuSn10 bronze and CuZn30 brass were investigated. Moreover, the effect of alloy elements of Cu, Sn and Zn on tribological and mechanical properties of journal bearings was evaluated. SAE 1050 steel shaft (journal) was used as counter abrader. Wear experiments were carried out at 20N loads, 1500rpm for 2.5h by using radial journal bearing wear test rig.
ÖZET Kaymalı yatak malzemesi olarak kalay-kurşun esaslı alaşımlar otomotiv endüstrisinde yaygın b... more ÖZET Kaymalı yatak malzemesi olarak kalay-kurşun esaslı alaşımlar otomotiv endüstrisinde yaygın bir şekilde kullanılmaktadır. Bu malzemelerin esasını oluşturan saf kalay ve kurşun ise iyi kayma özelliği olmasına rağmen çok düşük sertliğe sahip olduğundan düşük aşınma dayanımı göstermekte ve düşük mekanik özellikleri nedeniyle tek başına yatak malzemesi olarak kullanılmamaktadır. İyi bir kayma özelliğine sahip bu malzemelerin içerisine Al, Zn gibi elementler ilave edildiğinde kaymalı yataklarda iyi sonuçlar vermektedir. Bu çalışmada; kalay kurşun esaslı SnPbAlZn alaşımı ve bu malzemelerin esasını oluşturan saf Sn, saf Pb ve alaşım elementlerinden saf Al ve saf Zn dan üretilen kaymalı yatakların sürtünme ve aşınma özellikleri belirlenip, birbiriyle karşılaştırılmıştır. Karşı aşındırıcı olarak SAE 1050 çelik mil kullanılmıştır. Deneyler radyal kaymalı yatak aşınma deney cihazında 20 N yük, 1500 d/dak ve 2.5 saatte yapılmıştır. Sonuç olarak, SnPbAlZn malzemesi, saf durumda üretilen numu...
PurposeThis paper aims to determine the usage time of the test lubricant N0, prepared from base o... more PurposeThis paper aims to determine the usage time of the test lubricant N0, prepared from base oils of Aliaga Plant, Izmir, in gasoline and diesel‐engines, and the investigations of high‐temperature oxidation, engine‐protective properties, and property changes of the lubricant in performance time.Design/methodology/approachPhysical and chemical properties of the lubricating oil were initially established, and the oil was then subjected to Petter W‐1 gasoline and Petter AV‐1 diesel test engines. Dismantling of the engine parts was followed by the examination of pistons, piston rings and bearings, and analysis of the lubricant was also undertaken. The engine performance test results and the quality control of the lubricating oil assessments were evaluated according to the International Engine Lubricant Specifications.FindingsThe lubricating oil, under sluggish experimental conditions, appears to meet a 40‐hour test in gasoline engines and a 120‐hour test in diesel engines with the sp...
Uploads
Papers by Enver Atik