A split-flow capillary electrophoresis electrospray ionization mass spectrometry (CE/ESI-MS) inte... more A split-flow capillary electrophoresis electrospray ionization mass spectrometry (CE/ESI-MS) interface is introduced, in which the electrical connection to the CE capillary outlet is achieved by diverting part of the CE buffer out of the capillary through an opening near the capillary outlet. The CE buffer exiting the opening contacts a sheath metal tube which acts as the CE outlet/ESI shared electrode. In cases in which the ESI source uses a metal needle, the voltage contact to the CE buffer is achieved by simply inserting the outlet of the CE capillary, which contains an opening, into the existing ESI needle (thereby greatly simplifying the CE to MS interfacing). As a result of the concentration-sensitive nature of ESI, splitting a small percentage of the CE flow has minimal effect on the sensitivity of detection. In addition, because the liquid is flowing through the opening and out of the capillary, there is no dead volume associated with this interface. Moreover, bubble formation due to redox reactions of water at the electrode does not effect CE/ESI-MS performance, because the actual metal/liquid contact occurs outside of the CE capillary. The sensitivity associated with a sheathless CE/MS interface, the ease of fabrication, universality, and lack of any dead volume make this design a superior CE/ESI-MS interface. The performance of this interface is demonstrated by analyses of a peptide standard and a protein digest using a variety of capillary dimensions.
Nonprotein amino acids from nine species of cycad seeds were analyzed as N-ethoxycarbonyl ethyl e... more Nonprotein amino acids from nine species of cycad seeds were analyzed as N-ethoxycarbonyl ethyl ester (ECEE) derivatives by positive chemical-ionization gas chromatography-mass spectrometry. Based on the retention times and mass spectrometry analyses, 12 nonprotein amino acids were identified in these seeds. In addition to the excitatory and putative neurotoxin beta-N-methylamino-L-alanine (BMAA), the known neurotoxin beta-N-oxalylamino-L-alanine (BOAA) was detected from the seeds of Macrozamia moorei and M. communis, and delta-N-oxalyl-ornithine was obtained from the Cycas revoluta seeds. A novel nonprotein amino acid named cycasindene, previously reported from C. revoluta, was also found in the seeds of members of the C. angulata and C. rumphii complex. Eight additional known nonprotein amino acids were also identified. This is the first report of the neurotoxin BOAA from cycad seeds.
A new capillary electrophoresis/mass spectrometry technique is introduced for attomole detection ... more A new capillary electrophoresis/mass spectrometry technique is introduced for attomole detection of primary amines (including several neurotransmitters), amino acids, and their d/l enantiomers in one run through the use of a complexation reagent while using only approximately 1 nL of sample. The technique uses underivatized amino acids in conjunction with an underivatized capillary, which significantly reduces cost and analysis time. It was found that when (+)-(18-crown-6)-2,3,11,12-tetracarboxylic acid (18-C-6-TCA, MW 440) was used as the background electrolyte/complexation reagent during the capillary electrophoresis/electrospray ionization-mass spectrometry (CE/ESI-MS) analysis of underivatized amino acids, stable complexes were formed between the amino acids and the 18-C-6-TCA molecules. These complexes, which exhibited high ionization efficiencies, were detectable at attomole levels for most amino acids. The detection limits of the AA/18-C-6-TCA complexes were on the average more than 2 orders of magnitude lower than that of the free amino acids in solution. In addition to lower detection limits under CE/ESI-MS, a solution of 18-C-6-TCA in the concentration range of 5-30 mM provided high separation efficiency for mixtures of l-amino acids as well as mixtures of d/l-amino acids. By using a solution of 18-C-6-TCA as the background electrolyte in conjunction with an underivatized, 130-cm-long, 20-microm-i.d., 150-microm-o.d. fused-silica capillary and by monitoring the m/z range of the amino acid/18-C-6-TCA complexes (m/z 515-700), most of the standard amino acids and many of their enantiomers were separated and detected with high separation efficiency and high sensitivity (nanomolar concentration detection limits) in one run. The solutions of 18-C-6-TCA also worked well as the CE/ESI-MS BGE for low-level detection of several neurotransmitters and some of their d/l enantiomers as well as for the analysis of amino acids at endogenous levels in lysed red blood cells.
International Journal of Mass Spectrometry and Ion Processes, 1989
... TOWARD QUANTITATION OF ION/ MOLECULE KINETICS IN FOURIER TRANSFORM ION CYCLOTRON RESONANCE MA... more ... TOWARD QUANTITATION OF ION/ MOLECULE KINETICS IN FOURIER TRANSFORM ION CYCLOTRON RESONANCE MASS SPECTROMETRY MEHDI MOINI * and ... 8 RB Cody, SD Goodman, S. Ghaderi and JL Shohet, 35th ASMS Conference on Mass Spectrometry and ...
The conversion of a thermospray ionization (TSI) feature of a Finnigan-MAT TSQ-70 mass spectromet... more The conversion of a thermospray ionization (TSI) feature of a Finnigan-MAT TSQ-70 mass spectrometer to electrospray ionization (ESI) and its performance are described. The existing source, pumping capacity, flanges, and temperature controller of the TSQ-70 TS feature were used with a few modifications. Conversion of the commercial TS option to a simple and economically viable ES option has made the analysis of large biomolecules possible without expensive upgrades. To preserve the simplicity of the conversion, desolvation is effected by a heated-capillary tube (HCT). The HCT and its housing are inserted inside the TSQ-70 TS flange like a solid probe. Mass spectrometric results of low and high molecular weight biomolecules, the mass accuracy, sensitivity, and charge states of the observed ions are comparable to published results by other laboratories. Adequate spectral quality was obtained at short scan times, a required characteristic for interfacing ESI with separation methods such as capillary zone electrophoresis.
It was found that combining capillary electrophoresis (CE) and electrospray ionization mass spect... more It was found that combining capillary electrophoresis (CE) and electrospray ionization mass spectrometry (ESI-MS) overlays two controlled current techniques to form a three-electrode system (CE inlet, CE outlet/ES emitter, and MS inlet electrodes) in which the CE outlet electrode and the ES emitter electrode were shared between the CE and the ESI-MS circuits. Depending on the polarities and magnitudes of the voltages at the CE inlet, CE outlet/ES emitter, and MS inlet electrodes, the nature of the two redox reactions at the shared electrode was the same or different (both reduction, both oxidation, or one oxidation and the other reduction). Several redox buffers were introduced for controlling electrochemical reactions at the shared electrode. By reacting at this electrode, redox buffers were able to maintain electrode potentials below the onset of water electrolysis, thereby eliminating gas bubble formation and/or pH drift. The volume of the gas generated due to water electrolysis was used to quantitate water oxidation or reduction at this electrode. Two types of redox buffers were used. A reactive electrode with an oxidation potential below that of water was used as the electrode under anodic conditions. Also, a reactive compound with a redox potential below that of water was added to the CE and/or ESI running buffer. When the shared electrode was the anode of both CE and ESI-MS circuits, the use of iron or etched and sanded stainless steel (ss) wire, instead of platinum wire, suppressed bubble formation at the shared electrode. Under these conditions, corrosion of the Fe wire and formation of Fe2+ replaced oxidation of water, eliminating O2 gas bubble and H+ formation. When mixtures of peptides were analyzed, iron adducts of peptides were observed. For a fresh wire, however, the intensities of adduct ions were less than 3% of the protonated molecules. After a few days of operation, the intensities of the adduct ions increased to approximately 50%, due to rust formation on the Fe wire. On-column rinsing with a 40% solution of citric acid rejuvenated the Fe wire and reduced the adduct peak intensities to less than 3%. Unmodified ss wire did not quench bubble formation, which was attributed to its passivated surface. When Fe, ss, and Pt wires were used as the shared electrode under forward polarity CE and positive ESI mode, where the shared electrode acted as a cathode with respect to CE inlet and as an anode with respect to MS inlet, reduction of water at the cathodic end of the electrode and, in the case of ss and Pt wires, oxidation of water at the anodic end of the shared electrode produced a significant amount of bubbles. Under these conditions, however, a buffer containing 50 mM p-benzoquinone completely suppressed both cathodic reduction and anodic oxidation of water for CE currents up to 4 microA. Reduction of p-benzoquinone at the cathodic end of the shared electrode to hydroquinone, and oxidation of this hydroquinone at the anodic end of the electrode, replaced reduction and oxidation of water, eliminating bubble formation. A 0.1% acetic acid solution saturated with I2 was also found to suppress bubble formation at the cathode for CE currents up to 3 microA; however, strong iodine adduct ions were observed under CE/ESI-MS when a mixture of peptides was analyzed. The application of iron as an in-capillary electrode for the analysis of a peptide mixture and a protein digest demonstrated a high separation efficiency similar to when hydroquinone was used as a redox buffer.
A split-flow capillary electrophoresis electrospray ionization mass spectrometry (CE/ESI-MS) inte... more A split-flow capillary electrophoresis electrospray ionization mass spectrometry (CE/ESI-MS) interface is introduced, in which the electrical connection to the CE capillary outlet is achieved by diverting part of the CE buffer out of the capillary through an opening near the capillary outlet. The CE buffer exiting the opening contacts a sheath metal tube which acts as the CE outlet/ESI shared electrode. In cases in which the ESI source uses a metal needle, the voltage contact to the CE buffer is achieved by simply inserting the outlet of the CE capillary, which contains an opening, into the existing ESI needle (thereby greatly simplifying the CE to MS interfacing). As a result of the concentration-sensitive nature of ESI, splitting a small percentage of the CE flow has minimal effect on the sensitivity of detection. In addition, because the liquid is flowing through the opening and out of the capillary, there is no dead volume associated with this interface. Moreover, bubble formation due to redox reactions of water at the electrode does not effect CE/ESI-MS performance, because the actual metal/liquid contact occurs outside of the CE capillary. The sensitivity associated with a sheathless CE/MS interface, the ease of fabrication, universality, and lack of any dead volume make this design a superior CE/ESI-MS interface. The performance of this interface is demonstrated by analyses of a peptide standard and a protein digest using a variety of capillary dimensions.
Nonprotein amino acids from nine species of cycad seeds were analyzed as N-ethoxycarbonyl ethyl e... more Nonprotein amino acids from nine species of cycad seeds were analyzed as N-ethoxycarbonyl ethyl ester (ECEE) derivatives by positive chemical-ionization gas chromatography-mass spectrometry. Based on the retention times and mass spectrometry analyses, 12 nonprotein amino acids were identified in these seeds. In addition to the excitatory and putative neurotoxin beta-N-methylamino-L-alanine (BMAA), the known neurotoxin beta-N-oxalylamino-L-alanine (BOAA) was detected from the seeds of Macrozamia moorei and M. communis, and delta-N-oxalyl-ornithine was obtained from the Cycas revoluta seeds. A novel nonprotein amino acid named cycasindene, previously reported from C. revoluta, was also found in the seeds of members of the C. angulata and C. rumphii complex. Eight additional known nonprotein amino acids were also identified. This is the first report of the neurotoxin BOAA from cycad seeds.
A new capillary electrophoresis/mass spectrometry technique is introduced for attomole detection ... more A new capillary electrophoresis/mass spectrometry technique is introduced for attomole detection of primary amines (including several neurotransmitters), amino acids, and their d/l enantiomers in one run through the use of a complexation reagent while using only approximately 1 nL of sample. The technique uses underivatized amino acids in conjunction with an underivatized capillary, which significantly reduces cost and analysis time. It was found that when (+)-(18-crown-6)-2,3,11,12-tetracarboxylic acid (18-C-6-TCA, MW 440) was used as the background electrolyte/complexation reagent during the capillary electrophoresis/electrospray ionization-mass spectrometry (CE/ESI-MS) analysis of underivatized amino acids, stable complexes were formed between the amino acids and the 18-C-6-TCA molecules. These complexes, which exhibited high ionization efficiencies, were detectable at attomole levels for most amino acids. The detection limits of the AA/18-C-6-TCA complexes were on the average more than 2 orders of magnitude lower than that of the free amino acids in solution. In addition to lower detection limits under CE/ESI-MS, a solution of 18-C-6-TCA in the concentration range of 5-30 mM provided high separation efficiency for mixtures of l-amino acids as well as mixtures of d/l-amino acids. By using a solution of 18-C-6-TCA as the background electrolyte in conjunction with an underivatized, 130-cm-long, 20-microm-i.d., 150-microm-o.d. fused-silica capillary and by monitoring the m/z range of the amino acid/18-C-6-TCA complexes (m/z 515-700), most of the standard amino acids and many of their enantiomers were separated and detected with high separation efficiency and high sensitivity (nanomolar concentration detection limits) in one run. The solutions of 18-C-6-TCA also worked well as the CE/ESI-MS BGE for low-level detection of several neurotransmitters and some of their d/l enantiomers as well as for the analysis of amino acids at endogenous levels in lysed red blood cells.
International Journal of Mass Spectrometry and Ion Processes, 1989
... TOWARD QUANTITATION OF ION/ MOLECULE KINETICS IN FOURIER TRANSFORM ION CYCLOTRON RESONANCE MA... more ... TOWARD QUANTITATION OF ION/ MOLECULE KINETICS IN FOURIER TRANSFORM ION CYCLOTRON RESONANCE MASS SPECTROMETRY MEHDI MOINI * and ... 8 RB Cody, SD Goodman, S. Ghaderi and JL Shohet, 35th ASMS Conference on Mass Spectrometry and ...
The conversion of a thermospray ionization (TSI) feature of a Finnigan-MAT TSQ-70 mass spectromet... more The conversion of a thermospray ionization (TSI) feature of a Finnigan-MAT TSQ-70 mass spectrometer to electrospray ionization (ESI) and its performance are described. The existing source, pumping capacity, flanges, and temperature controller of the TSQ-70 TS feature were used with a few modifications. Conversion of the commercial TS option to a simple and economically viable ES option has made the analysis of large biomolecules possible without expensive upgrades. To preserve the simplicity of the conversion, desolvation is effected by a heated-capillary tube (HCT). The HCT and its housing are inserted inside the TSQ-70 TS flange like a solid probe. Mass spectrometric results of low and high molecular weight biomolecules, the mass accuracy, sensitivity, and charge states of the observed ions are comparable to published results by other laboratories. Adequate spectral quality was obtained at short scan times, a required characteristic for interfacing ESI with separation methods such as capillary zone electrophoresis.
It was found that combining capillary electrophoresis (CE) and electrospray ionization mass spect... more It was found that combining capillary electrophoresis (CE) and electrospray ionization mass spectrometry (ESI-MS) overlays two controlled current techniques to form a three-electrode system (CE inlet, CE outlet/ES emitter, and MS inlet electrodes) in which the CE outlet electrode and the ES emitter electrode were shared between the CE and the ESI-MS circuits. Depending on the polarities and magnitudes of the voltages at the CE inlet, CE outlet/ES emitter, and MS inlet electrodes, the nature of the two redox reactions at the shared electrode was the same or different (both reduction, both oxidation, or one oxidation and the other reduction). Several redox buffers were introduced for controlling electrochemical reactions at the shared electrode. By reacting at this electrode, redox buffers were able to maintain electrode potentials below the onset of water electrolysis, thereby eliminating gas bubble formation and/or pH drift. The volume of the gas generated due to water electrolysis was used to quantitate water oxidation or reduction at this electrode. Two types of redox buffers were used. A reactive electrode with an oxidation potential below that of water was used as the electrode under anodic conditions. Also, a reactive compound with a redox potential below that of water was added to the CE and/or ESI running buffer. When the shared electrode was the anode of both CE and ESI-MS circuits, the use of iron or etched and sanded stainless steel (ss) wire, instead of platinum wire, suppressed bubble formation at the shared electrode. Under these conditions, corrosion of the Fe wire and formation of Fe2+ replaced oxidation of water, eliminating O2 gas bubble and H+ formation. When mixtures of peptides were analyzed, iron adducts of peptides were observed. For a fresh wire, however, the intensities of adduct ions were less than 3% of the protonated molecules. After a few days of operation, the intensities of the adduct ions increased to approximately 50%, due to rust formation on the Fe wire. On-column rinsing with a 40% solution of citric acid rejuvenated the Fe wire and reduced the adduct peak intensities to less than 3%. Unmodified ss wire did not quench bubble formation, which was attributed to its passivated surface. When Fe, ss, and Pt wires were used as the shared electrode under forward polarity CE and positive ESI mode, where the shared electrode acted as a cathode with respect to CE inlet and as an anode with respect to MS inlet, reduction of water at the cathodic end of the electrode and, in the case of ss and Pt wires, oxidation of water at the anodic end of the shared electrode produced a significant amount of bubbles. Under these conditions, however, a buffer containing 50 mM p-benzoquinone completely suppressed both cathodic reduction and anodic oxidation of water for CE currents up to 4 microA. Reduction of p-benzoquinone at the cathodic end of the shared electrode to hydroquinone, and oxidation of this hydroquinone at the anodic end of the electrode, replaced reduction and oxidation of water, eliminating bubble formation. A 0.1% acetic acid solution saturated with I2 was also found to suppress bubble formation at the cathode for CE currents up to 3 microA; however, strong iodine adduct ions were observed under CE/ESI-MS when a mixture of peptides was analyzed. The application of iron as an in-capillary electrode for the analysis of a peptide mixture and a protein digest demonstrated a high separation efficiency similar to when hydroquinone was used as a redox buffer.
Uploads
Papers by Mehdi Moini