CB Aut
CB Aut
CB Aut
CB-AUT
AUTO
20°
E 07/14
B 07/14
cod. 4050857
ITALIANO 4 - 6
ENGLISH 7 - 9
FRANÇAIS 10 - 12
DEUTSCH 13 - 15
ESPAÑOL 16 - 18
NEDERLANDS 19 - 21
Italiano
• PRESENTAZIONE
Grazie ad una progettazione d’avanguardia è stato realizzato per il ventilconvettore un comando elettronico auto-
matico con elevato grado di sensibilità. Con questo comando, gestito da microprocessore, è possibile realizzare il
controllo del ventilconvettore grazie alle numerose funzioni ed opzioni previste. Le funzioni del comando sono:
• Accensione e spegnimento del ventilconvettore.
• Controllo della temperatura ambiente.
• Impostazione della temperatura ambiente desiderata (SET).
• Commutazione manuale od automatica delle 3 velocità di Ventilazione.
• Possibilità di selezionare il ciclo di funzionamento estivo o invernale direttamente dalla pulsantiera del comando, oppure:
- con un segnale elettrico: il comando é predisposto per il funzionamento invernale; alimentando con la fase (L = 230V~)
il morsetto IN2 del fan coil verrà azionato il selettore elettronico che commuterà il funzionamento in ciclo estivo.
- negli impianti a due tubi, in modo automatico tramite un CHANGE-OVER ( sonda T2 ).
• Negli impianti a 4 tubi con ventilconvettori corredati di valvole acqua ON-OFF e con presenza costante di due fluidi
( acqua calda e acqua fredda) nei circuiti, è possibile ottenere la commutazione automatica dalla fase riscaldamento
a quella di raffreddamento, e viceversa, in funzione dello scostamento esistente fra la temperatura ambiente e la
temperatura settata, con zona morta di 2°C.
• Inserendo sulla morsettiera (IN1) un segnale elettrico di fase (L = 230V~), tramite un timer o un semplice interrutto-
re, è possibile ottenere la variazione della temperatura-set impostata (-3°C inverno, +3°C estate; DIP5 = ON), oppure
l’esclusione totale del funzionamento del ventilconvettore per i periodi nei quali i locali non sono abitati (DIP5 = OFF).
• Durante il funzionamento estivo, con ventilatore in OFF, un timer metterà in funzione la ventilazione per 2 minuti
ogni 15 minuti.
• Collegando la sonda di minima (accessorio T3, posta tra le alette della batteria di scambio termico), nel ciclo in-
vernale, il ventilatore entrerà in funzione solamente se la temperatura dell’acqua è superiore a 36°C e verrà fermato
quando quest’ultima è inferiore a 32°C.
• Collegando la sonda di minima (accessorio T3, posta tra le alette della batteria di scambio termico), nel ciclo estivo,
il ventilatore entrerà in funzione solamente se la temperatura dell’acqua è inferiore a 20°C e verrà fermato quando
quest’ultima è superiore a 23°C.
Prima di chiudere il comando, verificare che la configurazione di default dei Dip-Switch e del jumper posti sulla
scheda elettronica soddisfi le proprie esigenze; in caso contrario programmare il controllo in relazione alle funzioni
desiderate.
= Estate-aria fredda
= Inverno-aria calda
20°
Attenzione!
Con comando in OFF il ventilconvettore
è ancora alimentato a 230V.
Per qualsiasi manutenzione assicurarsi
di aver tolto la tensione.
4
Italiano
• CARATTERISTICHE TECNICHE DEL CONTROLLO
1) alimentazione: 230V~
2) campo di regolazione del termostato da 9 a 32°C con differenziale 0.7 °C
3) n° 2 ingressi optoisolati per cambio stagionale remoto (IN2) e riduzione set o spegnimento comando (IN1)
4) n° 3 ingressi Sonde: T1 - sonda aria, T2 - sonda Change Over, T3 - Sonda di minima acqua
5) controllo stato sonde: nella situazione in cui la sonda aria risultasse interrotta o in corto, il comando si predispone in fun-
zionamento continuo (uscita valvole eccitate e ventilazione attiva) ed il led rosso posto sul frontalino del comando inizia a
lampeggiare.
• JUMPER MC3
DEFAULT
1-2 = Commutazione
Estate / Inverno locale.
MC3
MC3
2-3 = Commutazione
MC3 Estate / Inverno remota
con “IN2”.
5
Italiano
• NOTE DI INSTALLAZIONE
Dopo aver scelto le funzioni desiderate, fissare con Fig. 1
le viti fornite a corredo la mensolina portacomando
sulla spalla della struttura interna, ricordandosi di
stringere bene la vite. 2
Traslare la copertura in plastica sino al bordo
esterno del supporto (Fig.1).
1
Innestare la morsettiera del comando (MC) nella 2
morsettiera del FanCoil (MFC2). 1
Ricordarsi di stringere bene le viti della morsettiera.
3
Nel caso di attacchi idraulici destri il comando
deve essere installato a sinistra dell’apparecchio.
Dovendo spostare il lato degli attacchi idrauli-
ci in cantiere (possibile solo per le versioni con
motore centrifugo), il comando andrà installato
nella parte opposta al lato attacchi.
Le morsettiere, i cavi e il passacavo vanno rifissa-
ti sul lato opposto, avendo cura di togliere il pre-
tranciato dal foro dove sarà inserito il passacavo.
IMPORTANTE!: Con Fan Manuale, la ventola si attiva alla velocità impostata da commutatore.
6
English
• INTRODUCTION
Avant-garde design has created an easy to programme and highly sensitive automatic electronic control for the FAN COIL.
The fan coil can be operated via the numerous functions and options incorporated in this microprocessor-based control unit.
The basic functions of the control unit consist in:
• Turning the fan coil on and off.
• Control room temperature.
• Impostazione della temperatura ambiente desiderata (SET).
• Manual or automatic selection of the three fan speeds.
• Selecting the summer or winter operating cycle directly from the control switch, or:
- via an electric signal: The control unit is set for winter operation; supplying line voltage (L = 230V~) to the terminal
IN2 of the fan coil activates the electronic selector to switch into summer mode.
- in two-pipe systems, automatically using a CHANGE-OVER ( T2 probe ).
• In four-pipe fan coils with ON/OFF water valves and the two liquids (hot and cold water) constantly present in the circuits,
automatic switching between heating and cooling phases according to the difference between set temperature and
room temperature with a dead zone of ~2°C.
• By connecting a line signal (L = 230V~) on the terminal board (IN1), a timer or simple switch can be used to vary the
set temperature (-3°C winter, +3°C summer; DIP5 = ON), or totally exclude fan coil operation during periods when the
premises are unoccupied (DIP5 = OFF).
• During summer operation with the fan OFF, a timer activates the fan for 2 minutes every 15 minutes.
• In the winter cycle only, if a minimum sensor is connected (T3 accessory located between the fins of the heat
exchange coil), the fan coil will start up only if the water temperature rises above 36°C and shut down when water
temperature drops below 32°C.
• In the summer cycle only, if a minimum sensor is connected (T3 accessory located between the fins of the heat
exchange coil), the fan coil will start up only when water temperature drops below 20°C and shut down if the water
temperature rises above 23°C.
Before closing the control unit, check that the default configuration of the dip switches and the jumper on the electronic
board satisfies the requirements of the installation. If not, program the control unit in accordance with the required
functions.
= Summer-cold air
= Winter-warm air
20°
Attention!
With the control unit on OFF,
the fan coil is still supplied with 230 V.
Before carrying out maintenance,
always disconnect from the voltage.
7
English
• TECHNICAL CHARACTERISTICS OF THE CONTROL UNIT
1) Power supply: 230V~
2) Thermostat control range from 9 to 32°C with differential 0.7°C
3) 2 x optoinsulated inputs for remote seasonal changeover (IN2); reducing set point reduction or turning
off the control unit (IN1)
4) n° 3 inputs probes: T1 - air probe, T2 - Change Over probe, T3 - Probe minimum water
5) Probe status control: if the air probe is disconnected or short-circuited, the control unit switches to continuous opera-
tion (valve outputs energised and fan on) and the red LED on the front of the control unit starts flashing;
• FUNCTION SETTINGS
POSITION
DIP DEFAULT ON OFF
1 OFF THERMAL POWER STATION WITH FAN THERMAL POWER STATION WITH VALVES
• JUMPER MC3
DEFAULT
1-2 = Local Summer/Winter
switching
MC3
MC3
2-3 = Remote Summer /
MC3 Winter switching
with “IN2”.
8
English
• INSTALLATION NOTES
After choosing the required functions, fix the Fig. 1
control support bracket that is included in the
delivery on the edge of the internal structure;
always remember to tighten the screw very well.
2
Move the plastic cover up to the external edge
of the plated support (Fig.1). 1
Insert the terminal board of the control (MC) into
the terminal board of the fan coil (MFC2). 2
Take care and tighten the screws of the terminal
1
board.
3
Since we have to change the side of the water
connections in yard (possible only for versions with
centrifugal motor), the control must be installed in
the opposite side of the connections.
The connecting terminals, the cables and the fair-
lead should be fixed again on the opposite side,
taking care in removing the pre-sheared from
the hole where should be inserted the fair-lead.
IMPORTANT!: With Fan Manual, the fan operates at the speed set by the selector.
9
Français
• PRÉSENTATION
Une conception d’avant-garde a permis de réaliser pour le ventilo-convecteur une commande électronique automa-
tique facilement programmable très sensible. Avec cette commande, gérée par des microprocesseurs, il est possible
de commander le ventilo-convecteur grâce aux nombreuses fonctions et options prévues. Les fonctions de base de la
commande sont:
• Mise en marche et arrêt du ventilo-convecteur.
• Contrôle de la température ambiante.
• Programmation de la température ambiante voulue (SET).
• Sélection manuelle ou automatique des trois vitesses du ventilateur.
• Possibilité de sélectionner le cycle de fonctionnement été ou hiver directement à partir des commutateurs de commande, ou:
- avec un signal électrique: La commande est prévue pour le fonctionnement hiver; en alimentant la borne du ventilocovecteur
avec la phase (L = 230V~), le sélecteur électronique sera actionné et basculera le fonctionnement sur le cycle été (IN2).
- dans les installations à deux tubes, de façon automatique par un inverseur CHANGE-OVER ( Sonde T2 ).
• Dans les installations à quatre tubes avec des ventilo-convecteurs munis de vannes eau ON-OFF et avec la
présence constante des deux fluides (eau chaude et eau froide) dans les circuits, il est possible d’obtenir la com-
mutation automatique de la phase chauffage à celle de refroidissement, et vice versa, en fonction de l’écart entre la
température ambiante et la température programmée, avec une zone morte de ~2°C.
• En branchant sur le bornier (IN1) un signal électrique de ligne (L = 230V~), par l’intermédiaire d’un temporisateur ou
d’un simple interrupteur, on peut obtenir la variation de la température programmée (moins 3°C hiver, plus 3°C été;
DIP5 = ON), ou l’exclusion totale du fonctionnement du ventilo-convecteur pendant les périodes durant lesquelles les
locaux ne sont pas habités (DIP5 = OFF).
• Pendant le fonctionnement été, avec le ventilateur OFF, untemporisateur fera marcher la ventilation pendant 2 minutes
toutes les 15 minutes.
• En connectant la sonde de température minimale (accessoire T3 placée entre les ailettes de la batterie d’échan-
ge thermique), en cycle hiver seulement, le ventilateur ne se mettra en marche que si la température de l’eau est
supérieure à 36°C et s’arrêtera quand celle-ci est inférieure à 32°C.
• En connectant la sonde de température minimale (accessoire T3 placée entre les ailettes de la batterie d’échange
thermique), en cycle été seulement, le ventilateur ne se mettra en marche que si la température de l’eau est inférieu-
re à 20°C et s’arrêtera quand celle-ci est à supérieure 23°C.
Avant de fermer l’unité de commande vérifier que la configuration par défaut des Dip-Switch et du Jumper placés sur
la carte électronique répond aux exigences; si ce n’est pas le cas programmer l’unité de contrôle selon les fonctions
désirées.
= hiver-air chaud
Attention!
Quand la commande est sur OFF
le ventilo-convecteur est encore alimenté à 230V.
Avant toute opération d’entretien
s’assurer d’avoir couper le courant.
10
Français
• CARACTÉRISTIQUES TECHNIQUES DU CONTRÔLE
1) alimentation : 230V~
2) champ de réglage du thermostat de 9 à 32°C avec différentiel 0.7°C
3) n°2 entrées avec isolant optoélectrique pour changement saisonnier à distance (IN2) et réduction set ou arrêt commande (IN1)
4) n°3 entrées sondes: T1 - sonde air, T2 - Sonde pour Change Over, T3 - sonde de minima eau
5) contrôle état sonde: si la sonde de l’air est interrompue ou en court-circuit, la commande est activée pour un fonctionnement
continu (sortie vannes excitées et ventilation activée) et la led rouge placée sur le bandeau de la commande commence à
clignoter.
• PROGRAMMATIONS DE FONCTIONS
POSITION
DIP DÉFAUT ON OFF
• JUMPER MC3
DÉFAUT
1-2 = Commutation
Été/Hiver locale
MC3
MC3
2-3 = Commutation
MC3 Été/Hiver à distance
avec “IN2”
ATTENTION !: Avec la vitesse manuel, le ventilateur s’active à la vitesse définie par le commutateur.
12
Deutsch
• PRÄSENTATION
Dank einer avantgardistischen Projektierung wurde für den Lüftungskonvektor ein programmierbares und hochsensi-
bles elektronisches Automatik-Steuergerät realisiert. Mit dieser Mikroprozessorsteuerung kann der Lüftungskonvektor
über die zahlreichen Funktionen und Optionen kontrolliert werden. Die Grundfunktionen des Steuergeräts sind:
• Ein- und Ausschalten des Lüftungskonvektors.
• Kontrolle der Raumtemperatur.
• Einstellung der gewünschten Raumtemperatur (SET).
• Manuelle oder automatische Einstellung der drei Ventilatordrehzahlen.
• Möglichkeit des Einstellens von Sommer- oder Winterbetrieb direkt an den Schalter oder:
- mit einem elektrischen Signal: Die Steuerung ist für den Winterbetrieb ausgelegt; indem die Klemme des fan coil mit
der Phase (L = 230V~) versorgt wird, wird der elektronische Wählschalter IN2 betätigt, der den Betrieb auf Sommer
umschalter.
- bei 2-Leiter-Systemen, automatisch mittels CHANGE-OVER ( Fühler T2 ).
• Bei 4-Leiter-Systemen mit Lüftungskonvektoren mit Wasserventilen ON-OFF und bei ständiger Präsenz der beiden
Flüssigkeiten (Warmwasser und Kaltwasser) in den Kreisen, ist die automatische Umschaltung von Heiz- zu Kühl-
betrieb und umgekehrt möglich, je nach der vorliegenden Abweichung zwischen Raumtemperatur und eingestellter
Temperatur, mit einem Totbereich von ~2°C.
• Wenn am Klemmenbrett (IN1) ein elektrisches Netzsignal (L = 230V~) eingesetzt wird, kann mit einer Schaltur oder
einem einfachen Schalter die am Thermostat eingestellte Temperatur (minus 3°C beim Winterbetrieb, plus 3°C beim
Sommerbetrieb; DIP5 = ON) geändert, oder der Betrieb des Gebläse-konvektors für die Perioden, in denen die Räume
unbewohnt sind, ganz ausgeschlossen werden (DIP5 = OFF).
• Während des Sommerbetriebs und Ventilator auf OFF setzt eine Schaltur das Gebläse alle 15 Minuten 2 Minuten
lang in Gang.
• Durch Anschließen der Minimumsonde (Zubehör T3 zwischen den Lamellen des Wärmetauscherregisters) im Win-
terbetrieb, wird der Ventilator nur eingeschaltet, wenn die Wassertemperatur über 36°C beträgt, und ausgeschaltet,
wenn sie bis unter 32°C absinkt.
• Durch Anschließen der Minimumsonde (Zubehör T3 zwischen den Lamellen des Wärmetauscherregisters) im Som-
merbetrieb, wird der Ventilator nur eingeschaltet, wenn die Wassertemperatur unter 20°C absinkt, und ausgeschaltet,
wenn sie über 23°C beträgt.
Bevor die Kontrolleinheit geschlossen wird, muss kontrolliert werden, ob die Default-Konfiguration der Dip-Switches
und des Jumpers an der Elektronik-platine den Anforderungen entspricht; andernfalls die Kontrolleinheit entsprechend
der gewünschten Funktionen programmieren.
Achtung!
Bei Steuerung auf OFF
wird der Lüftungskonvektor weiter mit 230V gespeist.
Vor Wartungsarbeiten sicherstellen,
dass die Spannung abgehängt ist.
13
Deutsch
• TECHNISCHE MERKMALE DES STEUERGERÄTES
1) Spannungsversorgung: 230V~
2) Einstellbereich des Thermostats von 9 bis 32°C mit Differential 0.7°C
3) 2 optoisolierte Eingänge für Fern- Saisonumschaltung (IN2) und Verminderung des Einstellwerts oder Ausschalten des
Steuergerätes (IN1)
4) 3 Eingänge Sonden: T1 - LuftSonde, Fühler T2 für Change Over, Mindesttemperatursonde T3.
5) Kontrolle des Sondenstatus: falls die Luftsonde unterbrochen oder kurzgeschlossen ist, stellt sich das Steuergerät auf
(Ausgang Ventile erregt und Belüftung eingeschaltet) und die rote LED an der Bedienblende beginnt zu blinken.
• JUMPER MC3
DEFAULT
1-2 = Sommer/Winterumschaltung
in der bedienung
MC3
MC3
2-3 = Sommer/Winter
MC3 Ferm-Umschaltung “IN2”
1) Über die Tastatur des Steuergeräts anwählbar: Jumper J2 in Default-Position Pin 1-2 geschlossen.
2) Mit Fern-Freigabe anwählbar: Jumper J2 in Position Pin 2-3 geschlossen (Umschalter Sommer-/Winterbetrieb nicht aktiv).
14
Deutsch
• ANMERKUNGEN ZUR INSTALLATION
Nachdemdie gewünschten Funktionen eingestellt
wurden, mit der im Lieferumfang inbegriffenen
Schraube den Steuerungsträger an der Wange Fig. 1
der internen Struktur befestigen; Denken Sie da-
ran, die Schraube festzuziehen.
Die Kunststoff-Abdeckung ßis zum Ausserrand des 2
Halters verschieben (Fig.1).
Die Steuerungsklemmleiste (MC) in die Klemmleiste
1
der Lüfterspule (MFC2) einfügen.
2
Denken Sie daran, die Schrauben der Klemmleiste
anzuziehen.
1
Bei hydraulischen Anschlüssen auf der rechten Seite 3
muß der Antrieb links vom Gerät installiert werden.
Da die Seite der Hydraulischen Anschlüsse am Installa-
tionsort zu verschieben ist (möglich nur für die Versionen
mit Zentrifugalmotor), wird der Antrieb auf der gegenüber-
liegenden Seite, d.h. auf der Anschlußseite montiert.
Die Klemmleisten, die Kabel und die Kabelführung
werden auf der gegenüberliegenden Seite wie-
der befestigt, wobei darauf zu achten ist, die
Stanzrückstände vom Loch zu entfernen, in das
die Kabelführung eingefügt wurde.
ACHTUNG!: Mit Handbetrieb, wird der Lüfter mit der Geschwindigkeit durch die Schalter laufen.
15
Español
• PRESENTACIÓN
Gracias a un proyecto de vanguardia se ha realizado para el ventilador convector un mando electrónico automático,
fácilmente programable y con un alto grado de sensibilidad. Con este mando, gestionado por microprocesadores se
puede realizar el control del ventilador convector gracias a las numerosas funciones y opciones previstas.
Las funciones básicas del mando son:
• Encendido y apagado del ventilador convector.
• Control de la temperatura ambiente.
• Introducción de la temperatura ambiente deseada (SET).
• Selección manual o automática de las tres velocidades del ventilador.
• Posibilidad de seleccionar el ciclo de funcionamiento verano o invierno directamente desde el conmutador del mando, o:
- con una señal eléctrica: El control astá predispuesto para el funcionamiento invernal, alimentando con la
fase (L = 230V~); será accionado el borne del fan coil que conmutará el funcionamiento al ciclo veraniego (IN2).
- en las instalaciones con dos tubos, de forma automática mediante un CHANGE OVER ( Sonda T2 ).
• En las instalaciones con cuatro tubos con ventiladores convectores equipados con válvulas de agua ON-OFF y con
presencia constante de los dos fluidos (agua caliente y agua fría) en los circuitos, se puede obtener la conmutación
automática de la fase de calentamiento a la de enfriamiento, y viceversa, en función de la diferencia existente entre
la temperatura ambiente y la temperatura instaurada, con una zona muerta de ~ 2ºC.
• Aplicando en la borna de conexión (IN1) una señal eléctrica de línea (L = 230V~),mediante un temporizador o un
simple interruptor es posible conseguir la variación de la temperatura establecida (menos 3°C invierno, más 3°C
verano; DIP5 = ON), o la exclusión total del funcionamiento del fan coil durante los periodos en que no se utilizan los
cuartos (DIP5 = OFF).
• Durante el funcionamiento veraniego, con ventilador en OFF, un temporizador pone en marcha la ventilación duren-
te 2 minutos cada 15 minutos.
• Conectando la sonda de mínima (accesorio T3 situado entre las aletas de la batería de cambio térmico), en el ciclo
invernal, el ventilador entrará en función únicamente si la temperatura del agua es superior a 36ºC y se cerrará cuando
esta última sea inferior a 32ºC.
• Conectando la sonda de mínima (accesorio T3 situado entre las aletas de la batería de cambio térmico), en el ciclo
veraniego, el ventilador entrará en función únicamente si la temperatura del agua es inferior a 20ºC y se cerrará cuan-
do esta última sea superior a 23ºC.
Antes de cerrar el control, verificar que la configuración por defecto de los DipSwitch y del Jumper situados en la
ficha electrónica satisface las propias exigencias, en caso contrario programar el control en relación a las funciones
deseadas.
= Verano-aire frio
= Invierno-aire caliente
Atención!
Con el mando en OFF el ventilador convector
aun está alimentado a 230 V.
Antes de realizar cualquier operación de mantenimiento
asegurarse de haber cortado la tensión.
16
Español
• CARACTERÍSTICAS TÉCNICAS DEL CONTROL
1) alimentación: 230V~.
2) campo de regulación del termostato de 9 a 32ºC con diferencial de 0.7ºC.
3) n° 2 entradas optoaisladas para cambio estacional remoto (IN2) y reducción set o corte mando (IN1).
4) n° 3 entradas de sondas: T1 - sonda de aire, T2 - sonda para Change Over, T3 - Sonda de mínima.
5) control del estado de las sondas: si la sonda de aire resultara interrumpida o en cortocircuito, el mando se pone en funcio-
namiento continuo (salida válvulas excitadas y ventilación activada) y el led rojo situado en la parte frontal del mando empieza
a parpadea.
• JUMPER MC3
DEFAULT
1-2 = Conmutación
Verano/Invierno local
MC3
MC3
2-3 = Conmutación
MC3 Verano/Invierno remota
mediante “IN2”.
18
Nederland
• PRESENTATIE
Dankzij een avant-gardistisch ontwerp, werd voor de ventilator-convector een makkelijk te programmeren automati-
sche en elektronische bediening gerealiseerd, met een grote gevoeligheid. Met deze bediening, beheerd door micro-
processoren, kan de ventilator-convector worden bestuurd m.b.v. de talrijke functies en opties. De basisfuncties van
de bediening zijn de volgende:
• In- en uitschakelen van de ventilator-convector.
• Bediening van de omgevingstemperatuur.
• Afstellen van de gewenste omgevingstemperatuur (SET).
• Manuele of automatische instelling van de drie snelheden van de ventilator.
• Mogelijke selectie van zomer-of wintercyclus, rechtstreeks met de drukknoppen van de bediening, of :
- met een elektrisch signaal: De bediening is voor winterwerking voorbereid; door met de fase (L = 230V~) klem IN2 van
de ventilatorconvector te voeden, wordt de elektronische keuzeschakelaar bediend die de werking op de zomercyclus zal
overzetten.
- voor installaties met twee leidingen, op automatische wijze m.b.v. een CHANGE-OVER ( T2-sonde ).
• In de installaties met vier leidingen, voorzien van een ventilator-convector met ON-OFF-waterkleppen en met een con-
stante aanwezigheid van beide vloeistoffen (warm en koud water) in de leidingen, kan de automatische omschakeling
worden bekomen van de verwarmings- en de afkoelingsfasen, in functie van het verschil tussen de omgevingstemperatuur
en de ingestelde temperatuur (SET), met een dode zone van ~2°C.
• Door een elektrisch lijnsignaal (L = 230V~) via een timer of een eenvoudige schakelaar naar het klemmenbord (IN1)
te sturen, kan de variatie van de ingestelde temperatuur (-3°C in de winter, +3°C in de zomer; DIP5 = ON) verkregen
worden, ofwel de totale uitschakeling van de ventilatorconvector in de periodes waarin de vertrekken niet bewoond
zijn (DIP5 = OFF).
• Tijdens de zomerwerking, als de ventilator op OFF staat, schakelt een timer de ventilator elke 15 min. gedurende 2 min. in.
• Door de minimumsonde aan te sluiten (optie T3 gemonteerd tussen de klemmen van de batterij voor de warmtewisse-
ling), alleen in de wintercyclus, treedt de ventilator alleen in werking als de temperatuur van het water 36°C overschrijdt,
en wordt uitgeschakeld als die temperatuur minder dan 32°C bedraagt.
• Door de minimumsonde aan te sluiten (optie T3 gemonteerd tussen de klemmen van de batterij voor de warmtewisse-
ling), alleen in de zomercyclus, treedt de ventilator alleen in werking als de temperatuur minder dan 20°C bedraagt, en
wordt uitgeschakeld als die temperatuur van het water 23°C overschrijdt.
OPGELET!
Met de bediening in de OFF-stand
wordt de ventilator-convector nog gevoed met 230V.
Breng het apparaat buiten spanning
vóór elke onderhoudsbeurt.
19
Nederland
• TECHNISCHE EIGENSCHAPPEN BEDIENING
1) voeding: 230V~
2) Regelbereik thermostaat van 9 tot 32°C met differentiaal 0.7°C
3) 2 optisch geïsoleerde ingangen voor seizoensomschakeling (IN2) van op afstand en reductie afstelling of uitscha-
keling bediening (IN1).
4) 3 ingangen sondes: T1 - luchtsonde, T2-sonde voor Change Over, Uitschakelthermostaat T3
5) Controle toestand sonde: in gevallen waarin de luchtsonde onderbroken is of een kortsluiting ondergaat, gaat de bediening over op de
continue werking (uitgangskleppen bekrachtigd en ventilatie actief) en begint het rood controlelampje vooraan op de bediening te knipperen.
• AFSTELLEN FUNCTIES
POSITIE
DIP DEFAULT ON OFF
THERMOSTATERING MET
1 OFF VENTILATORLUCHTKOELER THERMOSTATERING MET KLEPPEN
• JUMPER MC3
STANDAARDCONFIGURATIE
1-2 = Seizoensschakelaar
van het apparaat
MC3
MC3
2-3 = Omschakeling
MC3 Seizoenen van op
afstand met “IN2”.
20
Nederland
• OPMERKINGEN BIJ DE INSTALLATIE
Na selectie van de gewenste functies, bevestig de
drager van de bediening met de bijgeleverde schro- Fig. 1
ef aan de zijwand van de binnenstructuur. Zet de
schroef goed aan.
Verplaats het plastic lid tot aan de burtenrand van 2
de drager (Fig.1).
Voer het klemmenbord van de bediening (MC) in het 1
klemmenbord van de ventilator-convector (MFC2).
Zet de schroeven van het klemmenbord goed aan. 2
In het geval van rechtse hydraulische aansluitingen, 1
moet de bediening links van het apparaat worden
gemonteerd.
3
Aangezien de zijde van de hydraulische aanslui-
tingen ter plaatse moet worden veranderd (alleen
mogelijk voor de versies CRC met centrifugemotor),
wordt de bediening gemonteerd aan de zijde tegeno-
ver de aansluitingen.
Fixeer de klemmenborden, kabels en kabelgoot opnieuw
aan de tegenoverliggende zijde, en haal de bescherming
uit de uitsparing waar de kabelgoot moet komen.
OPGELET!: Met snelheid handleiding, zal de ventilator draaien op de door de schakelaar snelheid.
21
ISTRUZIONE PER L’INSTALLAZIONE
DELLA SONDA ARIA (T1)
ATTENZIONE: Per un corretto funzionamento
della sonda eseguire l’installazione come indi-
cato nelle istruzioni
• Collegare la sonda aria al connettore T1 sulla
scheda di potenza
MOBILE VERTICALE
VERTICAL CASING
CARROSSERIE VERTICALE
SENKRECHTES GEHÄUSE
MÓVIL VERTICAL
VERTICAAL MEUBEL
22
APPLICAZIONE DELLA SONDA DI MINIMA T3
(optional cod. 3021090)
Se si utilizza la sonda di minima, bisogna procedere nel seguente modo:
Inserire la sonda di minima tra le alette della batteria (1) tenendola
leggermente inclinata verso il basso.
Collegare la sonda al connettore T3 sulla scheda (2).
23
Sonda T2 per Change-Over (optional cod. 9025310)
Solamente sui ventilconvettori in esecuzione per impianti a due tubi, la commutazione estate/inverno può avvenire in
modo automatico applicando, sulla tubazione acqua che alimenta la batteria, la sonda Change-Over T2 (opzionale).
La sonda va posizionata prima della valvola a tre vie.
In base alla temperatura rilevata dalla sonda, l’apparecchio si predispone in funzionamento estivo o invernale.
A = Tubazione acqua
B = Sonda
C = Isolante anticondensa
TH2O>30°C
- INVERNO
15°C 30°C - WINTER
- HIVER
- WINTER
- INVIERNO
- WINTER
T2 TH2O<26°C
TH2O>19°C
- SOLO VENTILAZIONE
- FAN ONLY
- VENTILATION SEULE
- NUR BELUFTUNG
- SOLO VENTILACION
- ALLEEN VENTILATIE
25
• LEGENDA • LEGENDE
E = Elettrovalvola acqua (impianto a 2 tubi) E = Wasserventil (Anlage mit 2 Rohren)
E1 = Valvola acqua calda E1 = Warmwasserventil
E2 = Valvola acqua fredda E2 = Kaltwasserventil
M = Motoventilatore M = Motorventilator
MC = Morsettiera del cablaggio MC = Verkabelungsklemmleiste
MFC2 = Morsettiera del FanCoil MFC2 = Klemmenbrett des Gebläsekonvektors
T1 = Sonda aria T1 = Lufttemperaturfühler
T3 = Sonda di minima NTC (Optional cod. T3 = Mindesttemperatur-Sonde NTC (Optional cod.
3021090) 3021090)
Q1 = Interruttore di manovra sezionatore Q1 = Hauptschalter
EH = Resistenza Elettrica EH = Elektrischer Widerstand
F = Scheda Filtro elettrostatico F = Elektronische Filterplatine
CH = Cambio stagionale esterno CH = Externe Betriebsartwahl
• LEGEND • LEYENDA
E = Water solenoid valve (two tube installation) E = Electroválvula agua (instalación 2 tubos)
E1 = Hot water solenoid valve E1 = Electroválvula agua caliente
E2 = Cold water solenoid valve E2= Electroválvula agua fria
M = Fan M = Motoventilador
MC = Terminal board of the wiring-in MC= Regleta de conexiones
MFC2 = Fan Coil terminal board MFC2= Borna de conexión del ventiloconvector
T1 = Air probe T1 = Sonda aire
T3 = NTC Low temperature cut-out thermostat T3= sonda de minima NTC (agua) (Opción cod.
(Optional cod. 3021090) 3021090)
Q1 = Two Poles Disconnector Q1 = Interruptor General
EH = Electrical heater EH = Resistencia eléctrica
F = Electronic filter F = Ficha filtro electrónico
CH = External season mode switch-over CH = Cambio estacional externo
• LÉGENDE • LEGENDE
E = électrovanne eau (installation 2 tuyauteries) E = Elektromagnetische klep (installane met 2 leidingen)
E1 = électrovanne eau chaude E1 = Elektromagnetische kep warm water
E2 = électrovanne eau froide E2 = Elektromagnetische klep koud water
M = Motoventilateur M = Motorventilator
MC = Boîte à bornes du câblage MFC2 = Klemmenbord ventilator-convector
MFC2 = Bornier du ventilo-convecteur MC = Klemmenbord bekabeling
T1 = Sonde air T1 = Luchtsonde
T3 = Sonde de température minimum NTC T3 = Watersonde NTC (Optie cod. 3021090)
(option cod. 3021090) Q1 = Hoofdschakelaar
Q1 = Interrupteur General EH = Elektrische weerstand
EH = Résistance électrique F = Schakeling elektronische filter
F = Carte filtre électronique CH = Externe seizoensomschakeling
CH = Changement de saison extérieur
26
CB-AUT Code 9066318 CB-AUT Code 9066318
SENZA VALVOLE / WITHOUT VALVES CON 1 VALVOLA / WITH 1 VALVE
OHNE VENTILE / SANS VANNES MIT 1 VENTIL / AVEC 1 VANNE
SIN VÁLVULAS / ZONDER KLEPPEN CON 1 VÁLVULA / MET EEN KLEP
PE L N 4 5 6 7 8 9 10 11 12 13 14 15
MFC2
AUTO
CH-IN2
L(230Vac)
M IN1
230V 50Hz L(230Vac)
20°
1 2 3 4 5 1 2 3 4 5 6 T1 T2 T3
230Vac
50Hz
L N CB-AUT Code 9066318
CON 2 VALVOLE / WITH 2 VALVES
MIT 2 VENTILE / AVEC 2 VANNES
CON 2 VÁLVULAS / MET TWEE KLEPPEN
Q1
PE
1 2 3 4 5 6 7 8 9 10 11 12
MC
PE L N 4 5 6 7 8 9 10 11 12 13 14 15
MFC2
PE L N 4 5 6 7 8 9 10 11 12 13 14 15
MCF2 CH-IN2
L(230Vac)
CH-IN2 M E1 IN1
L(230Vac)
L(230Vac) 230V 50Hz
M IN1
L(230Vac)
230V 50Hz
E2