The experiment about Diode Characteristic had been done. This experiment has a goal. The goal was... more The experiment about Diode Characteristic had been done. This experiment has a goal. The goal was to determine diode characteristics. The methods used in this experiment are by arrange the circuit like in the picture, then turn on the power supply. The voltages on power supply set up. After that, set the oscilloscope so it displays V/div 10 V and time/div by 10 ms/div. Look at the output signal on oscilloscope. Rearrange the circuit by adding variations of capacitors and diodes. This experiment used 1N4001 diodes, a 16 V 100 mikrofarad Elco, a project board, a Power Supply, a 10 kΩ resistor, a CT trafo, and an oscilloscope. The results from this experiments are diode has a characteristic which can rectify the circuit current. The signal made by diode on the oscilosscope variates with the variations on the number of diodes and capacitor. The signal formed by diode in Picture 3.1 was same and arranged above the x-axis. Signal that formed by Picture 3.2 arranged above the x-axis. The signal formed by diode in Picture 3.3 was same and arranged above the x-axis and the signal curve was identical with the signal on Picture 3.1 but without a gap distance between the wave peaks. Signal formed on Picture 3.4 similar with Picture 3.2 but with shorter distance from wave peak to wave hill.
The experiment about BJT DC Analysis had been done. This experiment has three goals. The goals wa... more The experiment about BJT DC Analysis had been done. This experiment has three goals. The goals was to analyze PNP and NPN transistor as a switch, to find Vmin and Imin on Basis to light up the LED (pnp and npn), and to find the Hfe values which is and. The methods used in this experiment are by set up the devices, then the devices arranged as seen on Picture 2.1. After that, the voltage source turned on and the voltage measured using AVO meter. Next, potentio resistance which is used determined. Basis current, emittor current, and voltage between basis and ground measured. The lamp observed. Those steps repeated with variations of potentio resistance. The results from this experiments are transistor can be functioned as a switch by control the sum of current in basis, collector, and emitter terminal; The values of Imin on PNP and NPN transistor needed to light up the LED lamp are 0,154 on PNP and 0,009 on NPN, and the average Hfe values which are and on PNP circuit are XXX and on NPN circuit are 19,4433 and-0,12593; and on NPN circuit are 0,971068 and 316,1754.
Telah dilakukan percobaan spektrometer dengan tujuan untuk mempelajari teori spektrometer prisma ... more Telah dilakukan percobaan spektrometer dengan tujuan untuk mempelajari teori spektrometer prisma dengan pendekatan eksperimental, mengamati spektrum warna cahaya dari panjang gelombang tertentu, menentukan indeks bias prisma kaca, dan menentukan panjang gelombang dengan menggunakan prisma yang telah dikalibrasi. Percobaan ini dilakukan dengan cara mengamati spektrum warna lampu gas melalui teleskop, kemudian diukur besar sudut pelurus kolimator. Dari percobaan yang telah dilakukan, secara fisis telah terjadi penguraian cahaya polikromatik menjadi cahaya-cahaya monokromatik oleh prisma. Kesimpulan dari praktikum ini yaitu cahaya polikromatik dapat diuraikan menjadi cahaya-cahaya monokromatik karena dibiaskan oleh prisma. Dari semua spektrum warna yang diperoleh, panjang gelombang paling besar dimiliki oleh cahaya merah dan paling pendek dimiliki oleh cahaya ungu. Dari percobaan menggunakan lampu gas neon diperoleh indeks bias prisma sebesar 1,427 sedangkan menggunakan lampu gas helium diperoleh indeks bias prisma sebesar 1,4094. Panjang gelombang cahaya dari percobaan menggunakan lampu gas neon yaitu cahaya merah 665,793; kuning 596,555; hijau 533,324; dan ungu 452,044. Pada percobaan dengan lampu gas helium, didapat panjang gelombang merah 733,476; kuning 609,025, hijau 512,151; biru 481,414; dan ungu 429,094.
Telah dilakukan percobaan photovoltaic dengan tujuan agar mampu menjelaskan fenomena photovoltaic... more Telah dilakukan percobaan photovoltaic dengan tujuan agar mampu menjelaskan fenomena photovoltaic pada solar cell, mengetahui pengaruh intensitas cahaya lampu pijar terhadap daya output solar cell, mengetahui pengaruh lebar solar cell terhadap daya output solar cell, dan mengetahui pengaruh panjang gelombang cahaya terhadap daya output solar cell. Percobaan ini dilakukan dengan cara menyinari permukaan solar cell menggunakan lighting module dengan terlebih dahulu diatu nilai V input, kemudian mencatat nilai V ouput dan I outpu yang ditunjukkan oleh rangkaian. Dari percobaan yang telah dilakukan, secara fisis telah terjadi pelepasan elektron dari lapisan semikonduktor sehinggan elektron mengalir pada rangkaian dan menimbulkan arus listrik. Kesimpulan dari praktikum ini yaitu fenomena photovoltaic pada solar cell terjadi karena lightning module dinyalakan dan memancarkan sehingga menyinari permukaan solar cell. P-N junction yang ada pada solar cell akan dibawa menuju proses pemanasan dalam temperatur tinggi dan waktu yang singkat. Bagian p memiliki kelebihan lubang, dan bagian n memiliki kelebihan elektron. Lubang-lubang pada sisi-p akan cenderung untuk berdifusi menuju sisi-n, dan elektron-elektron pada sisi-n akan berdifusi menuju sisi-p. Muatan mengalir sampai muatan total positif tetap pada sisi-n dan pada muatan negatif total tetap pada sisi-p menghasilkan medan listrik yang akan menghentikan proses difusi tersebut; semakin besar tegangan pada rangkaian, maka intensitas nyala lampu yang dikeluarkan oleh lightning module juga akan semakin terang, dan daya output juga semakin besar; semakin lebar ukuran solar cell, maka daya outputnya akan semakin besar, walaupun berdasarkan teori jika ukuran solar cell semakin besar, maka daya outputnya juga akan semakin besar; dan semakin besar panjang gelombang cahaya yang dikenai pada solar cell, maka daya output yang dihasilkan akan semakin kecil.
The experiment about Power Triangle Circuit had been done. This experiment has several goals. Tho... more The experiment about Power Triangle Circuit had been done. This experiment has several goals. Those are to analyze the active power, reactive power, and passive power on AC circuit; and to compare the power triangle on RL circuit and RC circuit. The methods used in this experiment are by measuring the voltage source and currents that passed some points of RL and RC circuit so we can measure the total power on those nodes. This experiment used capacitor and inductor variations, where for RC circuit we used 1 capacitor and 2 parallel capacitors' and for RL circuit we used 1 inductor and 2 series inductors. The results from this experiments are the values of active power is 0,5074 W contained by resistor, the reactive power is 6,6942 VAR contained by inductor and capacitor. and the last is passive power which is 7,2631 as a result from the two powers. And then, the power triangle of RL and RC had the similar result.
Telah dilakukan percobaan cincin newton dengan tujuan untuk mempelajari peristiwa interferensi pa... more Telah dilakukan percobaan cincin newton dengan tujuan untuk mempelajari peristiwa interferensi pada percobaan Cincin Newton, menjelaskan fungsi-fungsi alat pada cincin newton, mengukur panjang gelombang lampu halogen menggunakan metode Cincin Newton, dan mencari keseksamaan panjang gelombang yang terukur dengan yang sebenarnya. Percobaan ini dilakukan dengan cara menyiapkan alat yang terdiri dari lampu halogen dengan sumber tegangan dan satu set alat Newton's Ring. Kemudian, posisi lensa diatur pada tempatnya. Lampu halogen dinyalakan, kemiringan reflektor diatur agar pantulan sinar dari sumber cahaya ke lensa bikonveks membentuk beberapa lingkaran. Putar skala mikrometer sekrup sampai posisi titik pusat tepat pada pola terang ke – n yang ingin kita amati. Skala yang terbaca pada putaran skala diukur dan dicatat pada tabel pengamatan. Dari percobaan yang telah dilakukan, secara fisis telah terjadi proses refleksi dan interferensi dari cahaya yang berasal dari lampu halogen. Kesimpulan dari praktikum ini yaitu peristiwa interferensi yang terjadi pada percobaan Cincin Newton dapat dipelajari melalui fenomena terbentuknya pola gelap-terang yang berasal dari interferensi cahaya refleksi dari lensa dan cermin datar, fungsi-fungsi alat pada percobaan Cincin Newton ini antara lain lampu halogen sebagai sumber cahaya yang akan diamati pola Cincin Newton-nya, pemutar skala untuk mengatur agar penunjuk pada mikroskop dapat tepat posisinya pada pita gelap ke – n yang ingin diketahui jari-jarinya, dan sebagainya; Panjang gelombang lampu halogen yang terukur adalah 0,000695727 mm, dan keseksamaan dari panjang gelombang yang terukur dengan yang sebenarnya adalah 100-6,055894 % = 93,94410569 %.
Telah dilakukan percobaan kisi difraksi dengan tujuan untuk mempelajari mempelajari gejala difrak... more Telah dilakukan percobaan kisi difraksi dengan tujuan untuk mempelajari mempelajari gejala difraksi, menera konstanta kisi difraksi, dan mengetahui pengaruh jarak kisi ke layar terhadap pola gelap terang yang dihasilkan. Percobaan ini dilakukan dengan cara mengamati pola gelap terang pada layar yang dihasilkan setelah cahaya melewati kisi, kemudian diukur kedudukan masing-masing pola terang pada layar dan jarak dari terang pusat terhadap terang ke-n. Dari percobaan yang telah dilakukan, secara fisis telah terjadi pendifraksian cahaya laser ketika melewati kisi. Sesuai dengan prinsip Huygens, cahaya yang lolos dari kisi ini akan menjadi sumber gelombang yang baru. Gelombang-gelombang ini akan membentuk superposisi baik konstruktif maupun destruktif yang akan tampak sebagai pola gelap-terang pada layar. Pola gelap terang akan terjadi pada layar secara selang-seling. Kesimpulan dari praktikum ini yaitu proses terjadinya difraksi cahaya adalah cahaya monokromatik melewati celah sempit dari kisi (celah) seolah-olah menyebar riak-riak gelombang cahaya. Amplitudo kedua gelombang akan bergabung untuk membuat interferensi konstruktif ataupun interferensi destruktif, nilai dari konstanta kisi difraksi pada kisi pertama adalah 110490,6842; sedangkan pada kisi kedua adalah 113482,6046; dan semakin jauh jarak dari kisi ke layar, maka akan semakin jauh pula jarak antara pola gelap-terang yang dihasilkan.
Telah dilakukan percobaan getaran teredam dengan tujuan untuk mengetahui jenis redaman pada perco... more Telah dilakukan percobaan getaran teredam dengan tujuan untuk mengetahui jenis redaman pada percobaan ini, mengetahui nilai amplitudo mula-mula dalam percobaan ini, mengetahui besar konstanta redaman pada percobaan ini, dan mengetahui pengaruh θ terhadap simpangan. Percobaan ini dilakukan dengan cara peralatan dirangkai dengan variasi ketinggian bidang miring yang diatur terhadap lantai. Bola besi digelindingkan dari atas bidang miring ke bagian dasar dimana terdapat sebuah pegas. Waktu beserta simpangan hingga simpangan yang kelima dicatat dengan pengulangan 8 kali. Langkah yang sama dilakukan untuk variasi ketinggian lainnya. Pengolahan data, perhitungan, dan analisis dilakukan hingga diperoleh hasil dari percobaan. Dari percobaan yang telah dilakukan, secara fisis telah terjadi fenomena getaran teredam yang mengakibatkan osilasi dari bola besi akan memiliki amplitudo yang semakin menurun dan akhirnya berhenti...
The experiment about Diode Characteristic had been done. This experiment has a goal. The goal was... more The experiment about Diode Characteristic had been done. This experiment has a goal. The goal was to determine diode characteristics. The methods used in this experiment are by arrange the circuit like in the picture, then turn on the power supply. The voltages on power supply set up. After that, set the oscilloscope so it displays V/div 10 V and time/div by 10 ms/div. Look at the output signal on oscilloscope. Rearrange the circuit by adding variations of capacitors and diodes. This experiment used 1N4001 diodes, a 16 V 100 mikrofarad Elco, a project board, a Power Supply, a 10 kΩ resistor, a CT trafo, and an oscilloscope. The results from this experiments are diode has a characteristic which can rectify the circuit current. The signal made by diode on the oscilosscope variates with the variations on the number of diodes and capacitor. The signal formed by diode in Picture 3.1 was same and arranged above the x-axis. Signal that formed by Picture 3.2 arranged above the x-axis. The signal formed by diode in Picture 3.3 was same and arranged above the x-axis and the signal curve was identical with the signal on Picture 3.1 but without a gap distance between the wave peaks. Signal formed on Picture 3.4 similar with Picture 3.2 but with shorter distance from wave peak to wave hill.
The experiment about BJT DC Analysis had been done. This experiment has three goals. The goals wa... more The experiment about BJT DC Analysis had been done. This experiment has three goals. The goals was to analyze PNP and NPN transistor as a switch, to find Vmin and Imin on Basis to light up the LED (pnp and npn), and to find the Hfe values which is and. The methods used in this experiment are by set up the devices, then the devices arranged as seen on Picture 2.1. After that, the voltage source turned on and the voltage measured using AVO meter. Next, potentio resistance which is used determined. Basis current, emittor current, and voltage between basis and ground measured. The lamp observed. Those steps repeated with variations of potentio resistance. The results from this experiments are transistor can be functioned as a switch by control the sum of current in basis, collector, and emitter terminal; The values of Imin on PNP and NPN transistor needed to light up the LED lamp are 0,154 on PNP and 0,009 on NPN, and the average Hfe values which are and on PNP circuit are XXX and on NPN circuit are 19,4433 and-0,12593; and on NPN circuit are 0,971068 and 316,1754.
Telah dilakukan percobaan spektrometer dengan tujuan untuk mempelajari teori spektrometer prisma ... more Telah dilakukan percobaan spektrometer dengan tujuan untuk mempelajari teori spektrometer prisma dengan pendekatan eksperimental, mengamati spektrum warna cahaya dari panjang gelombang tertentu, menentukan indeks bias prisma kaca, dan menentukan panjang gelombang dengan menggunakan prisma yang telah dikalibrasi. Percobaan ini dilakukan dengan cara mengamati spektrum warna lampu gas melalui teleskop, kemudian diukur besar sudut pelurus kolimator. Dari percobaan yang telah dilakukan, secara fisis telah terjadi penguraian cahaya polikromatik menjadi cahaya-cahaya monokromatik oleh prisma. Kesimpulan dari praktikum ini yaitu cahaya polikromatik dapat diuraikan menjadi cahaya-cahaya monokromatik karena dibiaskan oleh prisma. Dari semua spektrum warna yang diperoleh, panjang gelombang paling besar dimiliki oleh cahaya merah dan paling pendek dimiliki oleh cahaya ungu. Dari percobaan menggunakan lampu gas neon diperoleh indeks bias prisma sebesar 1,427 sedangkan menggunakan lampu gas helium diperoleh indeks bias prisma sebesar 1,4094. Panjang gelombang cahaya dari percobaan menggunakan lampu gas neon yaitu cahaya merah 665,793; kuning 596,555; hijau 533,324; dan ungu 452,044. Pada percobaan dengan lampu gas helium, didapat panjang gelombang merah 733,476; kuning 609,025, hijau 512,151; biru 481,414; dan ungu 429,094.
Telah dilakukan percobaan photovoltaic dengan tujuan agar mampu menjelaskan fenomena photovoltaic... more Telah dilakukan percobaan photovoltaic dengan tujuan agar mampu menjelaskan fenomena photovoltaic pada solar cell, mengetahui pengaruh intensitas cahaya lampu pijar terhadap daya output solar cell, mengetahui pengaruh lebar solar cell terhadap daya output solar cell, dan mengetahui pengaruh panjang gelombang cahaya terhadap daya output solar cell. Percobaan ini dilakukan dengan cara menyinari permukaan solar cell menggunakan lighting module dengan terlebih dahulu diatu nilai V input, kemudian mencatat nilai V ouput dan I outpu yang ditunjukkan oleh rangkaian. Dari percobaan yang telah dilakukan, secara fisis telah terjadi pelepasan elektron dari lapisan semikonduktor sehinggan elektron mengalir pada rangkaian dan menimbulkan arus listrik. Kesimpulan dari praktikum ini yaitu fenomena photovoltaic pada solar cell terjadi karena lightning module dinyalakan dan memancarkan sehingga menyinari permukaan solar cell. P-N junction yang ada pada solar cell akan dibawa menuju proses pemanasan dalam temperatur tinggi dan waktu yang singkat. Bagian p memiliki kelebihan lubang, dan bagian n memiliki kelebihan elektron. Lubang-lubang pada sisi-p akan cenderung untuk berdifusi menuju sisi-n, dan elektron-elektron pada sisi-n akan berdifusi menuju sisi-p. Muatan mengalir sampai muatan total positif tetap pada sisi-n dan pada muatan negatif total tetap pada sisi-p menghasilkan medan listrik yang akan menghentikan proses difusi tersebut; semakin besar tegangan pada rangkaian, maka intensitas nyala lampu yang dikeluarkan oleh lightning module juga akan semakin terang, dan daya output juga semakin besar; semakin lebar ukuran solar cell, maka daya outputnya akan semakin besar, walaupun berdasarkan teori jika ukuran solar cell semakin besar, maka daya outputnya juga akan semakin besar; dan semakin besar panjang gelombang cahaya yang dikenai pada solar cell, maka daya output yang dihasilkan akan semakin kecil.
The experiment about Power Triangle Circuit had been done. This experiment has several goals. Tho... more The experiment about Power Triangle Circuit had been done. This experiment has several goals. Those are to analyze the active power, reactive power, and passive power on AC circuit; and to compare the power triangle on RL circuit and RC circuit. The methods used in this experiment are by measuring the voltage source and currents that passed some points of RL and RC circuit so we can measure the total power on those nodes. This experiment used capacitor and inductor variations, where for RC circuit we used 1 capacitor and 2 parallel capacitors' and for RL circuit we used 1 inductor and 2 series inductors. The results from this experiments are the values of active power is 0,5074 W contained by resistor, the reactive power is 6,6942 VAR contained by inductor and capacitor. and the last is passive power which is 7,2631 as a result from the two powers. And then, the power triangle of RL and RC had the similar result.
Telah dilakukan percobaan cincin newton dengan tujuan untuk mempelajari peristiwa interferensi pa... more Telah dilakukan percobaan cincin newton dengan tujuan untuk mempelajari peristiwa interferensi pada percobaan Cincin Newton, menjelaskan fungsi-fungsi alat pada cincin newton, mengukur panjang gelombang lampu halogen menggunakan metode Cincin Newton, dan mencari keseksamaan panjang gelombang yang terukur dengan yang sebenarnya. Percobaan ini dilakukan dengan cara menyiapkan alat yang terdiri dari lampu halogen dengan sumber tegangan dan satu set alat Newton's Ring. Kemudian, posisi lensa diatur pada tempatnya. Lampu halogen dinyalakan, kemiringan reflektor diatur agar pantulan sinar dari sumber cahaya ke lensa bikonveks membentuk beberapa lingkaran. Putar skala mikrometer sekrup sampai posisi titik pusat tepat pada pola terang ke – n yang ingin kita amati. Skala yang terbaca pada putaran skala diukur dan dicatat pada tabel pengamatan. Dari percobaan yang telah dilakukan, secara fisis telah terjadi proses refleksi dan interferensi dari cahaya yang berasal dari lampu halogen. Kesimpulan dari praktikum ini yaitu peristiwa interferensi yang terjadi pada percobaan Cincin Newton dapat dipelajari melalui fenomena terbentuknya pola gelap-terang yang berasal dari interferensi cahaya refleksi dari lensa dan cermin datar, fungsi-fungsi alat pada percobaan Cincin Newton ini antara lain lampu halogen sebagai sumber cahaya yang akan diamati pola Cincin Newton-nya, pemutar skala untuk mengatur agar penunjuk pada mikroskop dapat tepat posisinya pada pita gelap ke – n yang ingin diketahui jari-jarinya, dan sebagainya; Panjang gelombang lampu halogen yang terukur adalah 0,000695727 mm, dan keseksamaan dari panjang gelombang yang terukur dengan yang sebenarnya adalah 100-6,055894 % = 93,94410569 %.
Telah dilakukan percobaan kisi difraksi dengan tujuan untuk mempelajari mempelajari gejala difrak... more Telah dilakukan percobaan kisi difraksi dengan tujuan untuk mempelajari mempelajari gejala difraksi, menera konstanta kisi difraksi, dan mengetahui pengaruh jarak kisi ke layar terhadap pola gelap terang yang dihasilkan. Percobaan ini dilakukan dengan cara mengamati pola gelap terang pada layar yang dihasilkan setelah cahaya melewati kisi, kemudian diukur kedudukan masing-masing pola terang pada layar dan jarak dari terang pusat terhadap terang ke-n. Dari percobaan yang telah dilakukan, secara fisis telah terjadi pendifraksian cahaya laser ketika melewati kisi. Sesuai dengan prinsip Huygens, cahaya yang lolos dari kisi ini akan menjadi sumber gelombang yang baru. Gelombang-gelombang ini akan membentuk superposisi baik konstruktif maupun destruktif yang akan tampak sebagai pola gelap-terang pada layar. Pola gelap terang akan terjadi pada layar secara selang-seling. Kesimpulan dari praktikum ini yaitu proses terjadinya difraksi cahaya adalah cahaya monokromatik melewati celah sempit dari kisi (celah) seolah-olah menyebar riak-riak gelombang cahaya. Amplitudo kedua gelombang akan bergabung untuk membuat interferensi konstruktif ataupun interferensi destruktif, nilai dari konstanta kisi difraksi pada kisi pertama adalah 110490,6842; sedangkan pada kisi kedua adalah 113482,6046; dan semakin jauh jarak dari kisi ke layar, maka akan semakin jauh pula jarak antara pola gelap-terang yang dihasilkan.
Telah dilakukan percobaan getaran teredam dengan tujuan untuk mengetahui jenis redaman pada perco... more Telah dilakukan percobaan getaran teredam dengan tujuan untuk mengetahui jenis redaman pada percobaan ini, mengetahui nilai amplitudo mula-mula dalam percobaan ini, mengetahui besar konstanta redaman pada percobaan ini, dan mengetahui pengaruh θ terhadap simpangan. Percobaan ini dilakukan dengan cara peralatan dirangkai dengan variasi ketinggian bidang miring yang diatur terhadap lantai. Bola besi digelindingkan dari atas bidang miring ke bagian dasar dimana terdapat sebuah pegas. Waktu beserta simpangan hingga simpangan yang kelima dicatat dengan pengulangan 8 kali. Langkah yang sama dilakukan untuk variasi ketinggian lainnya. Pengolahan data, perhitungan, dan analisis dilakukan hingga diperoleh hasil dari percobaan. Dari percobaan yang telah dilakukan, secara fisis telah terjadi fenomena getaran teredam yang mengakibatkan osilasi dari bola besi akan memiliki amplitudo yang semakin menurun dan akhirnya berhenti...
Uploads
Papers by Rizqi Ahmad Fauzan