Abtract: This paper presents the results of structural analysis of reinforced concrete deep beams... more Abtract: This paper presents the results of structural analysis of reinforced concrete deep beams with openings. The investigation parameter is the location of opening. Nonlinear structural analysis computer code SAFIR is used in simulation. Verifying works have been done for models using SAFIR code. Results from parametric studies show that when the location of the opening is far from the load path, the load resistance of the beam, with opening is similar to that of the solid beam. 1. Giới thiệu chung Dầm được gọi là dầm cao (Deep Beam) khi mang một trong các đặc điểm sau đây [1]: tỉ số giữa nhịp thông thủy và chiều cao dầm bé hơn hoặc bằng 4; trên dầm xuất hiện tải trọng tập trung trong khoảng bé hơn 2 lần chiều cao dầm tính từ mép gối đỡ. Dưới tác dụng của tải trọng, trong dầm hình thành các thanh chống chịu nén nối giữa vị trí đặt tải trọng và gối đỡ (hình 1). Đối với các cấu kiện dầm thông thường, chúng ta thường sử dụng giả thiết biến dạng phẳng để lập sơ đồ ứng suất cho tiết diện và giải bài toán tính toán cốt thép dựa trên các sơ đồ ứng suất tại trạng thái phá hoại. Tuy nhiên, đối với dầm cao giả thiết về biến dạng phẳng trong lý thuyết uốn không còn đúng nữa. Để tính toán dầm cao phải sử dụng phương pháp phân tích với phân bố biến dạng phi tuyến, hoặc quy về đơn giản bằng cách sử dụng mô hình giàn ảo (strut-and-tie method). Hình 1. Các trường hợp định nghĩa của dầm cao Với các dầm cao có khoét lỗ cho các đường ống kỹ thuật chạy qua, phân bố ứng suất biến dạng trong dầm càng trở nên phức tạp. Dựa trên các thí nghiệm được công bố tại tài liệu [2], tác giả đã sử dùng phần mềm phân tích phi tuyến kết cấu SAFIR để mô phỏng dầm có kể đến tính phi tuyến của vật liệu. Kết quả mô phỏng tương đối trùng khớp với kết quả thí nghiệm. Dùng mô hình vừa kiểm chứng, dầm cao bê tông được khảo sát với các vị trí lỗ khoét thay đổi. 2. Mô phỏng dầm bằng phần mềm SAFIR SAFIR là phần mềm máy tính được phát triển tại trường đại học Liège-Vương quốc Bỉ với mục
Tham khảo toàn diện từ cơ bản đến nâng cao Nhiều ví dụ & bài tập thực hành CÔNG THỨC VÀ HÀM MICRO... more Tham khảo toàn diện từ cơ bản đến nâng cao Nhiều ví dụ & bài tập thực hành CÔNG THỨC VÀ HÀM MICROSOFT EXCEL 97-2013 CÔNG CỤ TUYỆT VỜI CỦA BẠN Tổng hợp & trình bày TRẦN THANH PHONG TP. HCM, 02/07/2014 Tài liệu cần thiết cho người sử dụng bảng tính
QUÁ TRÌNH NGHIÊN CỨU VÀ KẾT QUẢ 1. Đặc điểm dầm chuyển Ưu điểm Giải quyết được việc trốn cột, tạo... more QUÁ TRÌNH NGHIÊN CỨU VÀ KẾT QUẢ 1. Đặc điểm dầm chuyển Ưu điểm Giải quyết được việc trốn cột, tạo không gian lớn cho tầng bên dưới, kết cấu chuyển có khả năng vượt nhịp lớn, nhịp có thể lên đến 16-20m, giảm kích thước cấu kiện của các tầng trên kết cấu chuyển. Khuyết điểm Tải trọng tập trung bên trên kết cấu chuyển khá lớn, khi xảy ra động đất kết cấu rất dễ phá hoại. Tính toán, thi công dầm chuyển tương đối phức tạp, khó khăn trong lắp dựng giàn giáo cũng như đổ bê tông toàn khối cấu kiện lớn. Trọng lượng bản thân công trình phân bố không đồng điều, tập trung khối lượng lớn ở tầng có dầm chuyển làm cho công trình dễ mất ổn định khi có ngoại lực tác dụng vào công trình (động đất, gió bão) và các kết cấu bên dưới của dầm chuyển dễ mất ổn định. 2. Phân loại và hướng dẫn sử dụng các phần tử trong việc mô hình kết cấu bằng phần mềm 2.1. Theo hình học kết cấu chuyển có 4 dạng cơ bản sau
grading-phân tích thành phần hạt sự xếp loại các hạt vật liệu giữa các kích cỡ khác nhau; thường ... more grading-phân tích thành phần hạt sự xếp loại các hạt vật liệu giữa các kích cỡ khác nhau; thường được diễn đạt bằng phần trăm tích luỹ lớn hơn hoặc nhỏ hơn của các cỡ sàng (sàng hở) hoặc phần trăm giữa từng loại của kích cỡ (sàng mở). grout-vữa rót một hỗn hợp vật liệu gốc xi măng và nước, có hoặc không có cốt liệu, theo tỉ lệ để tạo độ sệt có thể rót được mà không có sự phân tầng giữa các yếu tố tạo thành; cũng là hỗn hợp của các thành phần khác nhưng có độ sệt tương tự. grouting-rót vữa quá trình lắp đầy bằng vữa rót. (xem grout.) hardener-chất làm cứng 1. hoá chất (gồm một số fluosilicates hoặc silicate natri) thi công lên sàn bê tông để giảm mài mòn và bụi; hoặc 2. dưới dạng chất dính hoặc phủ hai thành phần, thành phần hóa học gây ra sự đóng sắn của thành phần nhựa. joint, construction-khe nối thi công bề mặt nơi mà hai bộ phận bê tông kế tiếp gặp nhau, nơi cắt ngang có thể cần độ kết dính mặc dù có thép đi qua. joint, expansion-khe nối giãn nỡ 1.sự chia cắt giữa các bộ phận nằm sát nhau trong một kết cấu để cho phép kết cấu dịch chuyển cho những nơi sự giãn nỡ có khả năng vượt quá sự co lại, hoặc 2.sự ngăn cách trên sàn lớn được chèn bằng vật liệu lấp đầy. 3.khe cô lập có khuynh hướng di chuyển độc lập giữa các phần sát nhau loss, slump-mất độ sụt lượng độ sụt của bê tông tươi đã trộn thay đổi trong một khoảng thời gian sau khi đã tiến hành đo độ sụt ban đầu trên mẫu. mix design-cấp phối xem mixture proportioning (thuật ngữ thường dùng). paste, cement-hồ xi măng chất kết dính cho bê tông và vữa bao gồm xi
Abtract: This paper presents the results of structural analysis of reinforced concrete deep beams... more Abtract: This paper presents the results of structural analysis of reinforced concrete deep beams with openings. The investigation parameter is the location of opening. Nonlinear structural analysis computer code SAFIR is used in simulation. Verifying works have been done for models using SAFIR code. Results from parametric studies show that when the location of the opening is far from the load path, the load resistance of the beam, with opening is similar to that of the solid beam. 1. Giới thiệu chung Dầm được gọi là dầm cao (Deep Beam) khi mang một trong các đặc điểm sau đây [1]: tỉ số giữa nhịp thông thủy và chiều cao dầm bé hơn hoặc bằng 4; trên dầm xuất hiện tải trọng tập trung trong khoảng bé hơn 2 lần chiều cao dầm tính từ mép gối đỡ. Dưới tác dụng của tải trọng, trong dầm hình thành các thanh chống chịu nén nối giữa vị trí đặt tải trọng và gối đỡ (hình 1). Đối với các cấu kiện dầm thông thường, chúng ta thường sử dụng giả thiết biến dạng phẳng để lập sơ đồ ứng suất cho tiết diện và giải bài toán tính toán cốt thép dựa trên các sơ đồ ứng suất tại trạng thái phá hoại. Tuy nhiên, đối với dầm cao giả thiết về biến dạng phẳng trong lý thuyết uốn không còn đúng nữa. Để tính toán dầm cao phải sử dụng phương pháp phân tích với phân bố biến dạng phi tuyến, hoặc quy về đơn giản bằng cách sử dụng mô hình giàn ảo (strut-and-tie method). Hình 1. Các trường hợp định nghĩa của dầm cao Với các dầm cao có khoét lỗ cho các đường ống kỹ thuật chạy qua, phân bố ứng suất biến dạng trong dầm càng trở nên phức tạp. Dựa trên các thí nghiệm được công bố tại tài liệu [2], tác giả đã sử dùng phần mềm phân tích phi tuyến kết cấu SAFIR để mô phỏng dầm có kể đến tính phi tuyến của vật liệu. Kết quả mô phỏng tương đối trùng khớp với kết quả thí nghiệm. Dùng mô hình vừa kiểm chứng, dầm cao bê tông được khảo sát với các vị trí lỗ khoét thay đổi. 2. Mô phỏng dầm bằng phần mềm SAFIR SAFIR là phần mềm máy tính được phát triển tại trường đại học Liège-Vương quốc Bỉ với mục
Tham khảo toàn diện từ cơ bản đến nâng cao Nhiều ví dụ & bài tập thực hành CÔNG THỨC VÀ HÀM MICRO... more Tham khảo toàn diện từ cơ bản đến nâng cao Nhiều ví dụ & bài tập thực hành CÔNG THỨC VÀ HÀM MICROSOFT EXCEL 97-2013 CÔNG CỤ TUYỆT VỜI CỦA BẠN Tổng hợp & trình bày TRẦN THANH PHONG TP. HCM, 02/07/2014 Tài liệu cần thiết cho người sử dụng bảng tính
QUÁ TRÌNH NGHIÊN CỨU VÀ KẾT QUẢ 1. Đặc điểm dầm chuyển Ưu điểm Giải quyết được việc trốn cột, tạo... more QUÁ TRÌNH NGHIÊN CỨU VÀ KẾT QUẢ 1. Đặc điểm dầm chuyển Ưu điểm Giải quyết được việc trốn cột, tạo không gian lớn cho tầng bên dưới, kết cấu chuyển có khả năng vượt nhịp lớn, nhịp có thể lên đến 16-20m, giảm kích thước cấu kiện của các tầng trên kết cấu chuyển. Khuyết điểm Tải trọng tập trung bên trên kết cấu chuyển khá lớn, khi xảy ra động đất kết cấu rất dễ phá hoại. Tính toán, thi công dầm chuyển tương đối phức tạp, khó khăn trong lắp dựng giàn giáo cũng như đổ bê tông toàn khối cấu kiện lớn. Trọng lượng bản thân công trình phân bố không đồng điều, tập trung khối lượng lớn ở tầng có dầm chuyển làm cho công trình dễ mất ổn định khi có ngoại lực tác dụng vào công trình (động đất, gió bão) và các kết cấu bên dưới của dầm chuyển dễ mất ổn định. 2. Phân loại và hướng dẫn sử dụng các phần tử trong việc mô hình kết cấu bằng phần mềm 2.1. Theo hình học kết cấu chuyển có 4 dạng cơ bản sau
grading-phân tích thành phần hạt sự xếp loại các hạt vật liệu giữa các kích cỡ khác nhau; thường ... more grading-phân tích thành phần hạt sự xếp loại các hạt vật liệu giữa các kích cỡ khác nhau; thường được diễn đạt bằng phần trăm tích luỹ lớn hơn hoặc nhỏ hơn của các cỡ sàng (sàng hở) hoặc phần trăm giữa từng loại của kích cỡ (sàng mở). grout-vữa rót một hỗn hợp vật liệu gốc xi măng và nước, có hoặc không có cốt liệu, theo tỉ lệ để tạo độ sệt có thể rót được mà không có sự phân tầng giữa các yếu tố tạo thành; cũng là hỗn hợp của các thành phần khác nhưng có độ sệt tương tự. grouting-rót vữa quá trình lắp đầy bằng vữa rót. (xem grout.) hardener-chất làm cứng 1. hoá chất (gồm một số fluosilicates hoặc silicate natri) thi công lên sàn bê tông để giảm mài mòn và bụi; hoặc 2. dưới dạng chất dính hoặc phủ hai thành phần, thành phần hóa học gây ra sự đóng sắn của thành phần nhựa. joint, construction-khe nối thi công bề mặt nơi mà hai bộ phận bê tông kế tiếp gặp nhau, nơi cắt ngang có thể cần độ kết dính mặc dù có thép đi qua. joint, expansion-khe nối giãn nỡ 1.sự chia cắt giữa các bộ phận nằm sát nhau trong một kết cấu để cho phép kết cấu dịch chuyển cho những nơi sự giãn nỡ có khả năng vượt quá sự co lại, hoặc 2.sự ngăn cách trên sàn lớn được chèn bằng vật liệu lấp đầy. 3.khe cô lập có khuynh hướng di chuyển độc lập giữa các phần sát nhau loss, slump-mất độ sụt lượng độ sụt của bê tông tươi đã trộn thay đổi trong một khoảng thời gian sau khi đã tiến hành đo độ sụt ban đầu trên mẫu. mix design-cấp phối xem mixture proportioning (thuật ngữ thường dùng). paste, cement-hồ xi măng chất kết dính cho bê tông và vữa bao gồm xi
Must-have management strategies for construction supervisors working in the field C onstruction S... more Must-have management strategies for construction supervisors working in the field C onstruction Supervision inspires supervisory excellence with proven tactics and techniques applied by thousands of construction supervisors over the past decade. Recognizing the unique and critical role the supervisor plays in project success, the book's leadership guidelines carve out a practical blueprint for motivating work performance and increasing productivity through effective communication. Key lessons emphasize adaptable strategies for managing risk and unexpected workflow challenges. Beginning with the definition and importance of supervision and ending with the increasingly important role construction supervisors will hold in the future, this book covers a wide range of topics, such as best practices for accomplishing project objectives, managing physical resources, schedules and costs, team building, and much more. Construction Supervision features: • A unique focus on field supervision and crew management • Coverage of supervision from the foreman to the superintendent level • An overview of technical skills whose mastery will build confidence and success for the supervisor • A detailed view of "soft" management and communication skills From planning and executing in the field to juggling responsibilities on the fly, Construction Supervision fosters preparedness with a broad range of supervisory situations one is likely to encounter on a commercial, residential, industrial, or institutional construction project, and offers sound advice for solving the most complex management issues. Jerald l. rounds, Phd, Pe, is Associated General Contractors Endowed Chair in Construction Management and Construction Engineering at the University of New Mexico. As a certified Class "A" construction superintendent in Denver, he served as project manager on a number of commercial building projects prior to more than thirty years as a construction educator. Concurrently, he has developed numerous training programs in project management and supervision for the construction industry. Most recently, he codeveloped the NECA Electrical Project Supervision training program with Robert Segner, with whom he has conducted "train the trainer" sessions for the past decade. robert o. segner Jr. is a professor of construction science in the College of Architecture at Texas A&M University. He followed years of construction practice with four decades in construction higher education. He has served as president of the American Council for Construction Education. Segner codeveloped the NECA Electrical Project Supervision training program with Jerald Rounds and has conducted "train the trainer" sessions for the past decade. He has developed and taught numerous other continuing education programs.
Uploads
Papers by Phuoc Dang