Search Results (95)

Shear thickening fluids (STFs) have garnered attention as potential enhancers of protective capabilities and for the optimization of Kevlar^® armor design. To assess the possible shear thickening properties and potential application in ballistic protection, ten formulations were developed by employing polyethylene glycol (PEG) or polypropylene glycol (PPG), along with fumed silica or Aerosil HDK^®. Rheological characterization facilitated the identification of formulations displaying shear thickening behavior. The potential integration of the selected shear thickening fluids (STFs) into Kevlar^®-based composites was investigated by studying the impact resistance of Kevlar^® soft armor structures. Also, high-velocity impact testing revealed that the distance between aramid layers plays a crucial role in the impact resistance effectiveness of Kevlar^®–STF composite structures and that there is a very narrow domain between optimal and undesired scenarios in which STF could facilitate the penetration of Kevlar. The introduction of STF between the Kevlar sheets disrupted this packing and the energy absorption capacity of the material was not improved. Only one formulation (PEG400, Aerosil 27 wt.%) led to a less profound traumatic imprint and stopped the bullet when it was placed between layers no.1 and no.2 from a total of 11 layers of Kevlar XP. These experimental findings align with the modeling and simulation of Kevlar^®–STF composites using Ansys simulation software (Ansys® AutoDyn 2022 R2). Full article

This study describes the development of hydrogel formulations with ionic crosslinking capacity and photocatalytic characteristics. The objective of this research is to provide an effective, accessible, “green”, and facile route for the decontamination of chemical warfare agents (CWAs, namely the blistering agent—mustard gas/sulfur mustard (HD)) from contaminated surfaces, by decomposition and entrapment of CWAs and their degradation products inside the hydrogel films generated “on-site”. The decontamination of the notorious warfare agent HD was successfully achieved through a dual hydrolytic–photocatalytic degradation process. Subsequently, the post-decontamination residues were encapsulated within a hydrogel membrane film produced via an ionic crosslinking mechanism. Polyvinyl alcohol (PVA) and sodium alginate (ALG) are the primary constituents of the decontaminating formulations. These polymeric components were chosen for this application due to their cost-effectiveness, versatility, and their ability to form hydrogen bonds, facilitating hydrogel formation. In the presence of divalent metallic ions, ALG undergoes ionic crosslinking, resulting in rapid gelation. This facilitated prompt PVA-ALG film curing and allowed for immediate decontamination of targeted surfaces. Additionally, bentonite nanoclay, titanium nanoparticles, and a tetrasulfonated nickel phthalocyanine (NiPc) derivative were incorporated into the formulations to enhance absorption capacity, improve mechanical properties, and confer photocatalytic activity to the hydrogels obtained via Zn²⁺—mediated ionic crosslinking. The resulting hydrogels underwent characterization using a variety of analytical techniques, including scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), viscometry, and mechanical analysis (shear, tensile, and compression tests), as well as swelling investigations, to establish the optimal formulations for CWA decontamination applications. The introduction of the fillers led to an increase in the maximum strain up to 0.14 MPa (maximum tensile resistance) and 0.39 MPa (maximum compressive stress). The UV-Vis characterization of the hydrogels allowed the determination of the band-gap value and absorption domain. A gas chromatography–mass spectrometry assay was employed to evaluate the decontamination efficacy for a chemical warfare agent (sulfur mustard—HD) and confirmed that the ionic crosslinked hydrogel films achieved decontamination efficiencies of up to 92.3%. Furthermore, the presence of the photocatalytic species can facilitate the degradation of up to 90% of the HD removed from the surface and entrapped inside the hydrogel matrix, which renders the post-decontamination residue significantly less dangerous. Full article

This paper presents research on several factors influencing the stabbing behaviour of stratified panels made of aramid fabric Twaron^® SRM509 Teijin Aramid BV (Arnhem, The Netherlands). The inputs in the test campaign were the number of layers, the impact energy, and the sample size. Tests were performed on small samples (130 mm × 130 mm) on an Instron^® CEAST 9350 drop-tower impact system (Norwood, MA, USA) and on larger samples (400 mm × 400 mm) using a test installation with the same values of the impact energy. Knife type S1 was used, with the geometry recommended in NIJ Standard 0115.00 Stab Resistance of Body Armor SEM, and macro photography investigations revealed the failure mechanisms of panel, layers and fibres. A very important conclusion of this study regarding the stabbing performance of fabric Twaron^® SRM 509 in particular, but also in general for panels for body protection is that a research study could start on small size samples, with an accurately instrumented machine, in order to establish the influence of significant factors of stab resistance (energy level, number of layers in a panel, etc.), as these samples are less expensive and less time consuming, but the study should be continued to examine larger size samples. The obtained data are useful for the prototype. Full article

Due to advances in additive manufacturing and prototyping, affordable and rapid microfluidic sensor-integrated assays can be fabricated using additive manufacturing, xurography and electrode shadow masking to create versatile platform technologies aimed toward qualitative assessment of acute cytotoxic or cytolytic events using stand-alone biochip platforms in the context of environmental risk assessment. In the current study, we established a nasal mucosa biosensing platform using RPMI2650 mucosa cells inside a membrane-integrated impedance-sensing biochip using exclusively rapid prototyping technologies. In a final proof-of-concept, we applied this biosensing platform to create human cell models of nasal mucosa for monitoring the acute cytotoxic effect of zinc oxide reference nanoparticles. Our data generated with the biochip platform successfully monitored the acute toxicity and cytolytic activity of 6 mM zinc oxide nanoparticles, which was non-invasively monitored as a negative impedance slope on nasal epithelial models, demonstrating the feasibility of rapid prototyping technologies such as additive manufacturing and xurography for cell-based platform development. Full article

Therapeutic vaccines are a promising alternative for active immunotherapy for different types of cancers. Therapeutic cancer vaccines aim to prevent immune system responses that are not targeted at the tumors only, but also boost the anti-tumor immunity and promote regression or eradication of the malignancy without, or with minimal, adverse events. Clinical trial data have pushed the development of cancer vaccines forward, and the US Food and Drug Administration authorized the first therapeutic cancer vaccine. In the present review, we discuss the various types of cancer vaccines and different approaches for the development of therapeutic cancer vaccines, along with the current state of knowledge and future prospects. We also discuss how tumor-induced immune suppression limits the effectiveness of therapeutic vaccinations, and strategies to overcome this barrier to design efficacious, long-lasting anti-tumor immune responses in the generation of vaccines. Full article

Unexpected atypical isolates of Bacillus cereus s.l. occasionally challenge conventional microbiology and even the most advanced techniques for anthrax detection. For anticipating and gaining trust, 65 isolates of Bacillus cereus s.l. of diverse origin were sequenced and characterized. The BTyper3 tool was used for assignation to genomospecies B. mosaicus (34), B. cereus s.s (29) and B. toyonensis (2), as well as virulence factors and toxin profiling. None of them carried any capsule or anthrax-toxin genes. All harbored the non-hemolytic toxin nheABC and sphygomyelinase spH genes, whereas 41 (63%), 30 (46%), 11 (17%) and 6 (9%) isolates harbored cytK-2, hblABCD, cesABCD and at least one insecticidal toxin gene, respectively. Matrix-assisted laser desorption ionization-time of flight mass spectrometry confirmed the production of cereulide (ces genes). Phylogeny inferred from single-nucleotide polymorphisms positioned isolates relative to the B. anthracis lineage. One isolate (BC38B) was of particular interest as it appeared to be the closest B. anthracis neighbor described so far. It harbored a large plasmid similar to other previously described B. cereus s.l. megaplasmids and at a lower extent to pXO1. Whereas bacterial collection is enriched, these high-quality public genetic data offer additional knowledge for better risk assessment using future NGS-based technologies of detection. Full article

Objectives: In the context of COVID-19, patients with a severe or critical illness may be more susceptible to developing secondary bacterial infections. This study aims to investigate the relationship between the use of prophylactic antibiotic therapy and the occurrence of bacterial or fungal isolates following the administration of tocilizumab in hospitalized COVID-19 patients who had previously received steroids during the first and second waves of the pandemic in Spain. Methods: This retrospective observational study included 70 patients hospitalized with COVID-19 who received tocilizumab and steroids between January and December 2020. Data on demographics, comorbidities, laboratory tests, microbiologic results, treatment, and outcomes were collected from electronic health records. The patients were divided into two groups based on the use of antibiotic prophylaxis, and the incidence of bacterial and fungal colonizations/infections was analyzed. Results: Among the included patients, 45 patients received antibiotic prophylaxis. No significant clinical differences were observed between the patients based on prophylaxis use regarding the number of clinically diagnosed infections, ICU admissions, or mortality rates. However, the patients who received antibiotic prophylaxis showed a higher incidence of colonization by multidrug-resistant bacteria compared to that of the subgroup that did not receive prophylaxis. The most commonly isolated microorganisms were Candida albicans, Enterococcus faecalis, Staphylococcus aureus, and Staphylococcus epidermidis. Conclusions: In this cohort of hospitalized COVID-19 patients treated with tocilizumab and steroids, the use of antibiotic prophylaxis did not reduce the incidence of secondary bacterial infections. However, it was associated with an increased incidence of colonization by multidrug-resistant bacteria. Full article

The contemporary geopolitical environment and strategic uncertainty shaped by asymmetric and hybrid threats urge the future development of hands-on training in realistic environments. Training in immersive, virtual environments is a promising approach. Immersive training can support training for contexts that are otherwise hard to access, dangerous, or have high costs. This paper discusses the challenges for virtual reality training in the CBRN (chemical, biological, radioactive, nuclear) domain. Based on initial considerations and a literature review, we conducted a survey and three workshops to gather requirements for CBRN training in virtual environments. We structured the gathered insights into four overarching themes—the future of CBRN training, ethical and safety requirements, evaluation and feedback, and tangible objects and tools. We provide insights on these four themes and discuss recommendations. Full article

The removal yield of organic substances present in water depends on the environmental conditions, on the chemical composition of the water and on the chemical substance dissolved in the water, which constitutes the substrate of the metabolic activities of the microalgae that use these substances in the biochemical reactions of cellular enzyme complexes. o-Chlorobenzylidene malononitrile (CS, to use its military designation) was synthesized in-house, for research purposes, by a condensing reaction between o-chlorobenzaldehide and malononitrilein the presence of diethylamine. The detection, identification and confirmation of o-chlorobenzylidenemalononitrile (coded CBM in this experimental study) was performed using gas chromatography–mass spectrometry (GC-MS) and the purity of CBM was 99%. The biodegradation capacity in the samples that contained the biological suspension, after 24 h and 96 h of incubation, was determined via GC-MS analysis, and no evidence of the presence of CBM or some metabolites of CBM was detected. In the parallel samples, a hydrolysis process of CBM at room temperature, without biological treatment, revealed two main metabolites, malononitrile and o-chlorobenzaldehyde, respectively. This study is focused on evaluating the biodegradation capacity of o-chlorobenzylidene malononitrile in the presence of a biological material, culture of Chlorella sp., in comparison with a classical hydrolysis process. The tests performed indicate that the suspension of Chlorella sp. consumed the entire amount of CBM and metabolites from the analyzed samples. The tests prove that the biological material can be used to decontaminate the affected areas. Full article

Background: Ceftobiprole is a fifth-generation cephalosporin that has been approved in Europe solely for the treatment of community-acquired and nosocomial pneumonia. The objective was to analyze the use of ceftobiprole medocaril (Cefto-M) in Spanish clinical practice in patients with infections in hospital or outpatient parenteral antimicrobial therapy (OPAT). Methods: This retrospective, observational, multicenter study included patients treated from 1 September 2021 to 31 December 2022. Results: A total of 249 individuals were enrolled, aged 66.6 ± 15.4 years, of whom 59.4% were male with a Charlson index of four (IQR 2–6), 13.7% had COVID-19, and 4.8% were in an intensive care unit (ICU). The most frequent type of infection was respiratory (55.8%), followed by skin and soft tissue infection (21.7%). Cefto-M was administered to 67.9% of the patients as an empirical treatment, in which was administered as monotherapy for 7 days (5–10) in 53.8% of cases. The infection-related mortality was 11.2%. The highest mortality rates were identified for ventilator-associated pneumonia (40%) and infections due to methicillin-resistant Staphylococus aureus (20.8%) and Pseudomonas aeruginosa (16.1%). The mortality-related factors were age (OR: 1.1, 95%CI (1.04–1.16)), ICU admission (OR: 42.02, 95%CI (4.49–393.4)), and sepsis/septic shock (OR: 2.94, 95%CI (1.01–8.54)). Conclusions: In real life, Cefto-M is a safe antibiotic, comprising only half of prescriptions for respiratory infections, that is mainly administered as rescue therapy in pluripathological patients with severe infectious diseases. Full article

In cases of accidental or deliberate incidents involving a harmful agent in urban areas, a detailed modelling approach is required to include the building shapes and spatial locations. Simultaneously, when applied to crisis management, a simulation tool must meet strict time constraints. This work presents a Lagrangian particle model (LPM) for computing atmospheric dispersion. The model is implemented in the nuclear decision support system ESTE CBRN, a software tool developed to calculate the atmospheric dispersion of airborne hazardous materials and radiological impacts in the built-up area. The implemented LPM is based on Thomson’s solution for the nonstationary, three-dimensional Langevin equation model for turbulent diffusion. The simulation results are successfully analyzed by testing compatibility with Briggs sigma functions in the case of continuous release. The implemented LPM is compared with the Joint Urban 2003 Street Canyon Experiment for instantaneous puff releases. We compare the maximum concentrations and peak times measured during two intensive operational periods. The modeled peak times are mostly 10–20% smaller than the measured. Except for a few detector locations, the maximum concentrations are reproduced consistently. In the end, we demonstrate via calculation on single computers utilizing general-purpose computing on graphics processing units (GPGPU) that the implementation is well suited for an actual emergency response since the computational times (including dispersion and dose calculation) for an acceptable level of result accuracy are similar to the modeled event duration itself. Full article

Outbreaks of viral hemorrhagic fever caused by filoviruses have become more prevalent in recent years, with outbreaks of Ebola virus (EBOV), Sudan virus (SUDV), and Marburg virus (MARV) all occurring in 2022 and 2023. While licensed vaccines are now available for EBOV, vaccine candidates for SUDV and MARV are all in preclinical or early clinical development phases. During the recent outbreak of SUDV virus disease, the Biomedical Advanced Research and Development Authority (BARDA), as part of the Administration for Strategic Preparedness and Response within the U.S. Department of Health and Human Services, implemented key actions with our existing partners to advance preparedness and enable rapid response to the outbreak, while also aligning with global partners involved in the implementation of clinical trials in an outbreak setting. Beyond pre-existing plans prior to the outbreak, BARDA worked with product sponsors to expedite manufacturing of vaccine doses that could be utilized in clinical trials. While the SUDV outbreak has since ended, a new outbreak of MARV disease has emerged. It remains critical that we continue to advance a portfolio of vaccines against SUDV and MARV while also expediting manufacturing activities ahead of, or in parallel if needed, outbreaks. Full article

The use of personal protective equipment (PPE) is essential to protect the human body in hazardous environments or where there is a risk of CBRN agents. However, PPE also poses a barrier to evaporative heat dissipation, therefore increasing heat accumulation in the body. In our research, we investigated the applicability of thermophysiological models for the prediction of thermal strain and the permissible working time in a contaminated environment when the usage of protective ensembles is required. We investigated the relationship between the thermal insulation characteristics of four types of PPE against CBRN agents and the induced thermal strain in a set of real physiological strain tests with human probands wearing the PPE in a climatic chamber. Based on the results, we compared the predictions using two thermophysiological models—Predicted Heat Strain Index (PHS) and FIALA-based model of thermal comfort (FMTK)—with the experimental data. In order to provide a user-friendly platform for the estimation of thermal stress in PPE, a user-friendly computational tool, Predictor of Thermal Stress (PTS), was developed. The PTS tool is based on an extensive database of simulated calculations using an FMTK model based on PPE characteristics, environmental conditions, individual parameters, and expected workload. The PTS tool was validated by means of the results from real tests in a climatic chamber. The PTS was shown to be an easy-to-use computational tool, which can be run on a regular PC, based on real data applicable for the estimation of the permissible work time limit with regard to thermal strain in PPE under various conditions. Full article

Skin infections are frequently treated via intravenous or oral administration of antibiotics, which can lead to serious adverse effects and may sometimes contribute to the proliferation of resistant bacterial strains. Skin represents a convenient pathway for delivering therapeutic compounds, ensured by the high number of blood vessels and amount of lymphatic fluids in the cutaneous tissues, which are systematically connected to the rest of the body. This study provides a novel, straightforward method to obtain nafcillin-loaded photocrosslinkable nanocomposite hydrogels and demonstrates their performance as drug carriers and antimicrobial efficacy against Gram-positive bacteria. The novel formulations obtained, based on polyvinylpyrrolidone, tri(ethylene glycol) divinyl ether crosslinker, hydrophilic bentonite nanoclay, and/or two types of photoactive (TiO₂ and ZnO) nanofillers, were characterized using various analytical methods (transmission electron microscopy (TEM), scanning electron microscopy–energy-dispersive X-ray analysis (SEM-EDX), mechanical tests (tension, compression, and shear), ultraviolet-visible spectroscopy (UV-Vis), swelling investigations, and via specific microbiological assays (“agar disc diffusion method” and “time-kill test”). The results reveal that the nanocomposite hydrogel possessed high mechanical resistance, good swelling abilities, and good antimicrobial activity, demonstrating a decrease in the bacteria growth between 3log₁₀ and 2log₁₀ after one hour of direct contact with S. aureus. Full article

Aerosolized anthrax (Bacillus anthracis) spores are of extreme health concern and can remain airborne for hours and contaminate all kinds of surfaces, constituting reservoirs from which resuspension is easily produced. The assessment of decontamination techniques must therefore consider both air and surfaces. In the present study, several kinds of disinfecting fogs were experimentally tested against Bacillus thuringiensis spores, which served as a surrogate for Bacillus anthracis, both as aerosols released into the air and spread on porous and non-porous surfaces with different positions and orientations. This technology removed Bacillus thuringiensis spores from the air in 20 min with just a 1 min application of fog. The dynamics and characteristics of the fog, related to aerosol and surface interactions, proved to be critical for optimal performance and decontamination. An optimal configuration could provide effective disinfection even on indirectly reached surfaces. In all cases, 8% hydrogen peroxide (H₂O₂) provided a higher disinfection rate than 2% glutaraldehyde. Full article