Search Results (157)

The water retention capacity of porous materials is crucial in various geotechnical and environmental engineering applications such as slope stability analysis, landfill management, and mining operations. Filtered tailings stacks are considered an alternative to traditional tailings dams. Nevertheless, the mechanical behaviour and stability of the material under different water content conditions are of concern because these stacks can reach considerable heights. The water behaviour in these structures is poorly understood, particularly the effects of the water content on the stability and potential for liquefaction of the stacks. This study aims to investigate the water retention and flow characteristics of compacted iron ore tailings in high columns to better understand their hydromechanical behaviour. The research used 5 m high columns filled with iron ore tailings from the Quadrilátero Ferrífero region in Minas Gerais, Brazil. The columns were prepared in layers, compacted, and instrumented with moisture content sensors and suction sensors to monitor the water movement during various stages of saturation, drainage, infiltration, and evaporation. The sensors provided consistent data and revealed that the tailings exhibited high drainage capacity. The moisture content and suction profiles were effectively established over time and revealed the dynamic water retention behaviour. The comparison of the data with the theoretical soil water retention curve (SWRC) demonstrated a good correlation which indicates that there was no hysteresis in the material response. The study concludes that the column setup effectively captures the water retention and flow characteristics of compacted tailings and provides valuable insights for the hydromechanical analysis of filtered tailings stacks. These findings can significantly help improve numerical models, calibrate material parameters, and contribute to the safer and more efficient management of tailings storage facilities. Full article

The southeastern rock base sea area is the most abundant wind resource area, and it is also the mainstream construction site of offshore wind farms (OWFs) in China. The weathered residual soil is the main seabed component in the rock base area, which is the important bearing stratum of the offshore wind turbine foundation. Previous studies on the mechanical properties of seabed materials and bearing characteristics of the pile foundations in OWFs have mainly focused on the submarine soil-based seabed, resulting in a lack of direct reference for the construction of offshore wind power in the rocky seabed. Therefore, the mechanical properties of weathered residual soil and the bearing behaviors of monopile foundations are mainly investigated in this study. Firstly, dynamic triaxial tests are conducted on the weathered residual soil, and experiments analyze insight into the evolution law of the hysteresis curve, cumulative strain, and stiffness attenuation. Then, the horizontal loading behaviors of monopile foundations in residual soil are analyzed by numerical simulations; more critically, the service performances under wind and wave coupling loads are evaluated, which provide a direct theoretical basis for the construction and design of offshore wind turbine foundations in rock base seabeds. Full article

Piezoelectric inkjet printing technology, known for its high precision and cost-effectiveness, has found extensive applications in various fields. However, the issue of residual vibration significantly limits its printing quality and efficiency. This paper presents a method for suppressing residual vibration based on the particle swarm optimization (PSO) algorithm. Initially, an improved PI model considering the nonlinear hysteresis characteristics of piezoelectric ceramics is established, and the model is identified through a strain gauge circuit to ensure its accuracy in describing the nonlinear hysteresis characteristics. Subsequently, a dynamic model of the piezoelectric inkjet printing system is constructed, with precise parameter identification achieved using the self-induction principle. This enables precise simulation of residual vibration. Finally, the driving waveform is optimized based on the PSO algorithm, with iterative calculations employed to find the optimal combination of driving waveform parameters, effectively suppressing residual vibration while ensuring sufficient injection energy. The results indicate that this method significantly reduces the amplitude of residual vibration, thereby effectively enhancing printing quality and stability. This research offers a novel solution for residual vibration suppression in piezoelectric inkjet printing technology, potentially advancing its applications in printing and biofabrication. Full article

Accurate estimation of soil moisture content (SMC) is vital for effective farmland water management and informed irrigation decision-making. The utilization of unmanned aerial vehicle (UAV)-based remote sensing technology to monitor SMC offers advantages such as mobility, high timeliness, and high spatial resolution, thereby compensating for the limitations of in-situ observations and satellite remote sensing. However, previous research has primarily focused on SMC diagnostics for the entire crop growth period, often neglecting the development of targeted soil moisture modeling paradigms that account for the specific characteristics of the canopy and root zone at different growth stages. Furthermore, the variations in soil moisture status between fields, resulting from the hysteresis of water flow in irrigation channels at different levels, may influence the development of soil moisture modeling schemes, an area that has been seldom explored. In this study, SMC models based on UAV spectral information were constructed using Random Forest (RF) and Particle Swarm Optimization-Support Vector Machine (PSO-SVM) algorithms. The soil moisture modeling paradigms (i.e., input–output mapping) under different growth stages and soil moisture conditions of summer maize were systematically compared and discussed, along with the corresponding physical interpretability. Our results showed that (1) the SMC modeling schemes differ significantly across the various growth stages, with distinct input–output mappings recommended for the early (i.e., jointing, tasselling, and silking stages), middle (i.e., blister and milk stages), and late (i.e., maturing stage) periods. (2) these machine learning-based models performed best at the jointing stage, while subsequently, their accuracy generally exhibited a downward trend as the maize grew. (3) the RF model demonstrates superior robustness in estimating soil moisture status across different fields (moisture conditions), achieving optimal estimation accuracy in fields with overall higher SMC in line with the PSO-SVM model. (4) unlike the RF model’s robustness in spatial SMC diagnostics, the PSO-SVM model more reliably captured the temporal dynamics of SMC across different growth stages of summer maize. This study offers technical references for future modelers in UAV-based SMC modeling across various spatial and temporal conditions, addressing both the types of models as well as their input features. Full article

Ocean circulation plays an important role in the formation and occurrence of extreme climate events. The study shows that the periodic variation of ocean circulation under strong wind stress is closely related to climate oscillation. Ocean circulation is a nonlinear dynamic system, which shows complex nonlinear characteristics, so the essence behind ocean circulation has not been clearly explained. Therefore, the response and evolution of the circulation system to wind stress are studied based on the bifurcation and catastrophe theories in nonlinear dynamics. First, the quasi-geostrophic gyre equation and the normalized gravity model are introduced and developed to study ocean circulation driven by wind stress, and solved using the Galerkin method. Then, the bifurcation and catastrophe behaviors of the system governed by the low-order ocean circulation model during the change in wind stress intensity and the coexistence of multiple equilibria in the circulation system are studied in detail. The results show that saddle and unstable nodes appear in the system after a cusp catastrophe. With the change in model parameters, the unstable node becomes the unstable focus, and then the subcritical Hopf bifurcation occurs. The system forms a bistable interval when the system undergoes a catastrophe twice, and the system shows hysteresis. In addition, multiple equilibrium states are coexisting in the circulating system, and the unstable equilibrium state always changes into a stable equilibrium state through vortex movement. Therefore, there is a route for the system to induce short-term climate oscillation, that is, in the multi-stable equilibrium state of the system, the vortex oscillates after being subject to small disturbances, and then triggers climate oscillation. Full article

This study conducted dynamic triaxial tests on a typical poured asphalt concrete material of core walls in Xinjiang, exploring the dynamic characteristics of poured asphalt concrete under various confining pressures, principal stress ratios, and vibration frequencies. On this basis, the dynamic constitutive relationship of poured asphalt concrete was investigated using the Hardin–Drnevich model. The results indicate that under different confining pressures, principal stress ratios, and vibration frequencies, the variation patterns of the backbone lines of dynamic stress-strain of poured asphalt concrete are basically identical, consistent with a hyperbolic curve. The confining pressure and principal stress ratio significantly affect the backbone line of dynamic stress-strain. By comparison, frequency has a minimal effect. The changing trends of dynamic elasticity modulus and damping ratio of poured asphalt concrete under various factors are almost the same. When the material has high dynamic stress and strain, the hysteresis loop is large. When the curve of the damping ratio becomes flat, the asymptotic constant can be used as the maximum damping ratio. The relationship between the reciprocal of the dynamic elasticity modulus and the dynamic strain of poured asphalt concrete exhibits a linear distribution. Under different ratios of confining pressure to principal stress, there are large discrepancies between the calculated values from the formula and the experimental fitting values of the maximum dynamic elasticity modulus, and the maximum relative errors reach 16.65% and 18.15%, respectively. Therefore, the expression for the maximum dynamic elasticity modulus was modified, and the calculated values using the modified formula were compared with the experimental fitting values. The relative errors are significantly reduced, and the maximum relative errors are 3.02% and 2.04%, respectively, in good agreement with the fitting values of the experimental data. The findings of this article render a theoretical basis and reference for the promotion and application of poured asphalt concrete. Full article

The application of tree of heaven (Ailanthus altissima (Mill.) Swingle) is constrained by its poor durability and dimensional stability. Despite exhibiting promising physical and mechanical properties comparable to ash wood (Fraxinus excelsior L.), it is regarded as an invasive species and receives limited attention in wood property enhancement research. This study subjected tree of heaven to heat treatment at 180 °C and 200 °C to investigate its sorption characteristics using dynamic vapor sorption tests. The results revealed a 13% reduction in equilibrium moisture content at 95% relative humidity and 25 °C after thermal modification at 180 °C and a 25% reduction after thermal modification at 200 °C. Increasing the treatment temperature lowered the moisture content ratio to 0.76 and shortened the conditioning time by up to 10%. The highest hysteresis, ranging from 3.39% to 3.88%, was observed at 70% relative humidity. Full article

Directional ionic migration in ultra-thin metal-oxide semiconductors under applied electric fields is a key mechanism for developing various electronic nanodevices. However, understanding charge transfer dynamics is challenging due to rapid ionic migration and uncontrolled charge transfer, which can reduce the functionality of microelectronic devices. This research investigates the supercapacitive-coupled memristive characteristics of ultra-thin heterostructured metal-oxide semiconductor films at TiO₂-In₂O₃/Au Schottky junctions. Using atomic layer deposition (ALD), we nano-engineered In₂O₃/Au-based metal/semiconductor heterointerfaces. TEM studies followed by XPS elemental analysis revealed the chemical and structural characteristics of the heterointerfaces. Subsequent AFM studies of the hybrid heterointerfaces demonstrated supercapacitor-like behavior in nanometer-thick TiO₂-In₂O₃/Au junctions, resembling ultra-thin supercapacitors, pseudocapacitors, and nanobatteries. The highest specific capacitance of 2.6 × 10⁴ F.g⁻¹ was measured in the TiO₂-In₂O₃/Au junctions with an amorphous In₂O₃ electron gate. Additionally, we examined the impact of crystallization, finding that thermal annealing led to the formation of crystalline In₂O₃ films with higher oxygen vacancy content at TiO₂-In₂O₃ heterointerfaces. This crystallization process resulted in the evolution of non-zero I-V hysteresis loops into zero I-V hysteresis loops with supercapacitive-coupled memristive characteristics. This research provides a platform for understanding and designing adjustable ultra-thin Schottky junctions with versatile electronic properties. Full article

The horizontal axis tidal turbine, as a crucial device for capturing tidal energy, has gained significant attention because it has better energy efficiency performance. Enhancing the performance of foils, a vital part of tidal turbine blades, can significantly improve tidal turbine performance. Among numerous methods to enhance the foil performance, the Gurney flap has gained significant attention due to its avoidance of complex structural design. Currently, there is limited research on optimizing the design of Gurney flaps while considering the dynamic performance of foils. In this study, the S809 foil with a blade cross-section was selected as the research subject, a multi-objective optimization design platform was created by integrating a multi-objective optimization algorithm with Computational Fluid Dy-namics (CFD) numerical simulation techniques. The objective of this platform is to enhance the dynamic performance of the hydrofoil by optimizing the geometric structure of the Gurney flap. The improvement of dynamic lift and the size of the dynamic stall hysteresis loop are used as objective variables in this study to evaluate the hydrofoil’s dynamic performance. The optimal Latin hypercube design method is used in the optimization process to choose sample locations, and the Kriging approximation model is used to determine the relationship between the design variables and the objective variables. Meanwhile, the Non-Dominated Sorting Genetic Algorithm-II (NSGA-II) is used to create a multi-objective optimization platform for solving the optimization problem, and the optimized results are validated using CFD. Comparative validation results show that quantifying the dynamic performance during hydrofoil pitching oscillation and using the optimal Latin hypercube design method and Kriging approximation model for optimizing the Gurney flap structure is rational and accurate. This study explores the mechanism of the Gurney flap through in-depth CFD numerical simulations and finds that the Gurney flap affects the flow characteristics at the hydrofoil’s trailing edge, thereby influencing the performance. It increases the pressure difference between the pressure and suction surfaces, thus enhancing the hydrofoil’s lift. Finally, this article provides three recommended parameters to improve the dynamic performance of the hydrofoil. This research can serve as a reference for the application of Gurney flaps in tidal turbine blade design. Full article

Quickly sensing humidity changes is required in some fields, such as in fuel cell vehicles. The micro humidity sensor used for the relative humidity (RH) measurement with fast response characteristics, and its numerical model and method are rare. This paper firstly presents a numerical model and method for a parallel plate capacitor and a numerical analysis of its dynamic characteristics. The fabrication of this sensor was carried out based on the numerical results, and, the main characteristics of its moisture-sensitive element are shown. This parallel plate capacitor is made using complementary metal-oxide semiconductor (CMOS)-compatible technology, with a P-type monocrystalline silicon wafer used as the substrate, a thin polyimide film (PI) between the upper grid electrode and the lower parallel plate electrode, and electrodes with a molybdenum–aluminum bilayer structure. The shape of the micro sensor is square with 3 mm on the side of the source field. The humidity sensor has a linearity of 0.9965, hysteresis at 7.408% RH, and a sensitivity of 0.4264 pF/%RH. The sensor displays an average adsorption time of 1 s and a minimum adsorption time of 850 ms when the relative humidity increases from 33.2% RH to 75.8% RH. The sensor demonstrates very good stability during a 240 h test in a 25 °C environment. The numerical model and method provided by this study are very useful for predicting the performance of a parallel plate capacitor. Full article

Carbon steel materials are widely used in mechanical transmission. Under different temperature and pressure service conditions, the microscopic changes of stress and strain that are difficult to detect and analyze by experimental means will lead to failure deformation, thus affecting their operational stability and life. In this study, the molecular dynamics method is used to simulate the heating–cooling phase transition process of common carbon steel materials. Austenite transformation temperatures of 980 K (0.2 wt.%) and 1095 K (0.5 wt.%) are acquired which is determined by the volume hysteresis before and after transformation, which is consistent with the results of JMatPro phase diagram analysis. The internal stress state of the material varies between compressive stress and tensile stress due to the change of phase structure, and the dislocation characteristics during the phase transition period are observed to change significantly. Then, an $\mathsf{\alpha }/\mathsf{\gamma }$ two-phase interface model is constructed to study the migration of the phase interface and the change of the phase structure by applying a continuously changing external load. At the same time, the transition pressure of $\mathsf{\alpha }\to \mathsf{ϵ}$ is obtained with a value of 37 GPa under three different initial loads showing the independence of the initial load and the historical path. Based on the molecular dynamics simulation and the phase diagram calculation of the carbon steel, the analysis method for the microstructure transformation and the stress–strain behavior of the phase interface under the external load can provide a reference for the design of microstructure and mechanical properties of alloy steel in the future. Full article

This paper studies a rotor dynamic stall control method using an alternating current dielectric barrier discharge (AC DBD) plasma actuator through numerical simulation methods. The flow field evolution during a dynamic stalling process under the excitation of AC DBD plasma discharge is analyzed using the two-dimensional Reynolds time-averaged (RANS) method. The impact of the AC DBD plasma discharge on the flow field is then simulated using the phenomenological method. The influence of the position and intensity of the plasma excitation on the static stall characteristics of the NACA0012 airfoil is also studied. Deformed mesh and dynamic mesh techniques are used to simulate an aerodynamic environment with variable incoming flow and variable angles of attraction on a rotor airfoil. The application of AC DBD plasma excitation for controlling mild and deep dynamic stalls of rotor blades is investigated. The obtained results show that the AC DBD plasma excitation accelerated the evolution and shedding of dynamic stall vortices and facilitated the reattachment of airflow. The application of plasma excitation allowed for significantly increasing the static stall angle of the airfoil and improving the lift coefficient. In addition, the intensity of the plasma excitation is a key factor affecting the control. Moreover, the application of AC DBD plasma excitation for rotor dynamic stalls allowed for reducing the size of the dynamic stall vortex, which helped mitigate the aerodynamic hysteresis effect caused by the dynamic stall and accelerated the recovery from aerodynamic forces. Full article

This study investigates viscoelastic guided wave properties (e.g., complex–wavenumber–, phase–velocity–, and attenuation–frequency relations) for multiple modes, including different orders of antisymmetric, symmetric, and shear horizontal modes in viscoelastic anisotropic laminated composites. To obtain those frequency–dependent relations, a guided wave characteristic equation is formulated based on a Legendre orthogonal polynomials expansion (LOPE)–assisted viscoelastodynamic model, which fuses the hysteretic viscoelastic model–based wave dynamics and the LOPE–based mode shape approximation. Then, the complex–wavenumber–frequency solutions are obtained by solving the characteristic equation using an improved root–finding algorithm, which leverages coefficient matrix determinant ratios and our proposed local tracking windows. To trace the solutions on the dispersion curves of different wave modes and avoid curve–tracing misalignment in regions with phase–velocity curve crossing, we presented a curve–tracing strategy considering wave attenuation. With the LOPE–assisted viscoelastodynamic model, the effects of material viscosity and fiber orientation on different guided wave modes are investigated for unidirectional carbon–fiber–reinforced composites. The results show that the viscosity in the hysteresis model mainly affects the frequency–dependent attenuation of viscoelastic guided waves, while the fiber orientation influences both the phase–velocity and attenuation curves. We expect the theoretical work in this study to facilitate the development of guided wave–based techniques for the NDT and SHM of viscoelastic anisotropic laminated composites. Full article

Benefiting from its high thermal conductivity, simple structure, and light weight, the pulsating heat pipe (PHP) can meet the requirements for high efficiency, flexibility, and low cost in industrial heat transfer applications such as aerospace detector cooling and vehicle thermal management. Compared to a PHP working at room temperature, the mechanism of a PHP with hydrogen as the working fluid differs significantly due to the unique thermal properties of hydrogen. In this paper, a two-dimensional model of a hydrogen PHP with a filling ratio of 51% was established to study the flow characteristics and thermal performance. The volume of fluid (VOF) method was used to capture the phase distribution and interface dynamics, and the Lee model was employed to account for phase change. To validate the model, a comparison was conducted between the simulation results and experimental data obtained in our laboratory. The simulation results show that the pressure and temperature errors were within 25% and 5%, respectively. Throughout a pressure oscillation cycle, the occurrence of uniform flow velocity, acceleration, and flow reversal can be attributed to the changes in the vapor–liquid phase distribution resulting from the effect of condensation and evaporation. In addition, when the fluid velocity was greater than 0.6 m/s, dynamic contact angle hysteresis was observed in the condenser. The results contribute to a deeper understanding of the flow and heat transfer mechanism of the hydrogen PHPs, which have not been yet achieved through visualization experiments. Full article

Wire rope is a complex structure made by twisting wires of various sizes in the longitudinal direction. It is used to support or move engineering structures and is subject to various tensions. Dynamic properties are important parameters to evaluate the resistance to bending deformation and vibration reduction of various structures. They are affected by the magnitude of tension. In this study, an experimental method for measuring the frequency-dependent characteristics of wire rope under tension is proposed. The study analyzed flexural wave propagation employing a vibration transfer function. Experimental results showed that the transfer function of wire rope under tension is affected by tension and bending stiffness. The Newton–Raphson method was employed to numerically measure wavenumbers of the wire rope. The bending stiffness and loss factor were determined from the wavenumbers. Changes in the bending stiffness and loss factor as the tension increased were explained by the dynamic behavior of the structure under tension. As the tension increased, the bending stiffness increased, and the loss factor decreased. Hysteresis analysis indicated that the energy dissipation of wire rope is greater than that of a steel beam due to the friction between the wires. Statistical analysis confirmed a significant correlation between dynamic characteristics and tension in wire rope. Full article