Search Results (717)

Radiative natural convection is of vital importance in the process of energy storage, power generation, and thermal storage technology. As the attenuation coefficients of many heat transfer media in these fields are high enough to be considered as optically thick media, like nanofluids or molten salts in concentrated solar power or phase change thermal storage, Rosseland approximation is commonly used. In this paper, we delve into the impact of thermal radiation on the Rayleigh-Bénard (RB) convection. Theoretical analysis has been conducted by modifying the Grossmann-Lohse (GL) model. Based on turbulent dissipation theory, the corresponding scaling laws in four main regimes are proposed. Direct numerical simulation (DNS) was also performed, revealing that radiation exerts a notable influence on both flow and heat transfer, particularly on the formation of large-scale circulation. By comparing with DNS results, it is found that due to the presence of radiation, the modified Nu scaling law in small Pr range of the GL model is more suitable for predicting the transport characteristics of optical thick media with large Pr. The maximum deviation between the results of DNS and prediction model is about 10%, suggesting the summarized scaling law can effectively predict the Nu of radiative RB convection. Full article

This paper presents a solar chimney that acts as a heat accumulator. It is based on its alternating charging (melting of the phase change material—PCM) and discharging (solidification), which helps to save energy and ensures stable operation of the solar chimney. In this paper, special attention has been paid to the heat dissipation process (solidification of the PCM). The theoretical model of solidification has been solved in an original way. This paper presents a new simple theoretical model for the solidification of the PCM on a flat plate and presents the results of numerical tests. The theoretical model presents a method for determining the heat transfer coefficient at the solidification front of the PCM. In addition, the heat transfer coefficient from the flowing air to the outer surface of the solidifying front plate was determined experimentally in an original way. The heat transfer coefficient values resulting from the experiments may be employed in order to calculate the heat transfer coefficient for air flowing through the slot of the collector in the solar chimney. The calculated value of the heat transfer coefficient was 18.55 W/m²K. Full article

This research article introduces a novel chaotic satellite system based on fractional derivatives. The study explores the characteristics of various fractional derivative satellite systems through detailed phase portrait analysis and computational simulations, employing fractional calculus. We provide illustrations and tabulate the phase portraits of these satellite systems, highlighting the influence of different fractional derivative orders and parameter values. Notably, our findings reveal that chaos can occur even in systems with fewer than three dimensions. To validate our results, we utilize a range of analytical tools, including equilibrium point analysis, dissipative measures, Lyapunov exponents, and bifurcation diagrams. These methods confirm the presence of chaos and offer insights into the system’s dynamic behavior. Additionally, we demonstrate effective control of chaotic dynamics using feedback active control techniques, providing practical solutions for managing chaos in satellite systems. Full article

It is highly desired yet challenging to develop advanced elastomers with excellent mechanical properties, including high strength and toughness. In this work, strong and tough rubber/rubber compound vulcanizates were facilely prepared by blending ethylene-propylene-methylene (EPM) and isoprene rubber (IR) together with dicumyl peroxide (DCP) and subsequent vulcanization, since both EPM and IR can be vulcanized synchronously by DCP and the well-crosslinked structure of EPM/IR vulcanizate presented a stable phase separation state. By tuning their composition, EPM/IR vulcanizates could present remarkably improved mechanical strength and toughness, as well as excellent energy dissipation and deformation recovery abilities. Furthermore, EPM/IR/SiO₂ nanocomposites with better properties were prepared by introducing silica nanoparticles into EPM/IR vulcanizates. It was found that the high toughness and strength of EPM/IR vulcanizates and EPM/IR/SiO₂ nanocomposites mainly resulted from the combination of stretchability of EPM and strain hardening of IR. Their excellent energy dissipation and deformation recovery abilities were related to the macromolecular characteristics of EPM and IR, compatibility between EPM and IR, and their crosslinking dynamics. Full article

Background: During the dissolution of amorphous solid dispersion (ASD) formulations, the drug load (DL) often impacts the release mechanism and the occurrence of loss of release (LoR). The ASD/water interfacial gel layer and its specific phase behavior in connection with DL strongly dictate the release mechanism and LoR of ASDs, as reported in the literature. Thermodynamically driven liquid-liquid phase separation (LLPS) and/or drug crystallization at the interface are the key phase transformations that drive LoR. Methods: In this study, a combination of Perturbed-Chain Statistical Associating Fluid Theory (PC-SAFT) thermodynamic modeling and in silico molecular simulation was applied to investigate the release mechanism and the occurrence LoR of an ASD formulation consisting of ritonavir as the active pharmaceutical ingredient (API) and the polymer, polyvinylpyrrolidone-co-vinyl acetate (PVPVA64). A thermodynamically modeled ternary phase diagram of ritonavir (PVPVA64) and water was applied to predict DL-dependent LLPS in the ASD/water interfacial gel layer. Microscopic Erosion Time Testing (METT) was used to experimentally validate the phase diagram predictions. Additionally, in silico molecular simulation was applied to provide further insights into the phase separation, the release mechanism, and aggregation behavior on a molecular level. Results: Thermodynamic modeling, molecular simulation, and experimental results were consistent and complementary, providing evidence that ASD/water interactions and phase separation are essential factors driving the dissolution behavior and LoR at 40 wt% DL of the investigated ritonavir/PVPVA64 ASD system, consistent with previous studies. Conclusions: This study provides insights into the potential of blending thermodynamic modeling, molecular simulation, and experimental research to comprehensively understand ASD formulations. Such a combined approach can be leveraged as a computational framework to gain insights into the ASD dissolution mechanism, thereby facilitating in silico screening, designing, and optimization of formulations with the benefit of significantly reducing the number of experimental tests. Full article

This study aims to investigate the toughening effects of rubber and thermoplastic particles on epoxy resin (EP), and to understand the mechanism underlying their synergistic effect. For this purpose, three EP systems were prepared using diglycidyl ether of bisphenol-A (DGEBA) epoxy resin (E-54) and 4,4-Diamino diphenyl methane (Ag-80) as matrix resin, 4,4-diaminodiphenyl sulfone (DDS) as a curing agent, and phenolphthalein poly (aryl ether ketone) particles (PEK-C) and carboxyl-terminated butyl liquid rubber (CTBN) as toughening agents. These systems are classified as an EP/PEK-C toughening system, EP/CTBN toughening system, and EP/PEK-C/CTBN synergistic toughening system. The curing behavior, thermal properties, mechanical properties, and phase structure of the synergistic-toughened EP systems were comprehensively investigated. The results showed that PEK-C did not react with EP, while CTBN reacted with EP to form a flexible block polymer. The impact toughness of EP toughened by PEK-C/CTBN was improved obviously without significantly increasing viscosity or decreasing thermal stability, flexural strength, and modulus, and the synergistic toughening effect was significantly higher than that of the single toughening system. The notable improvement in toughness is believed to be due to the synergistic energy dissipation effect of PEK-C/CTBN. Full article

Phase-change materials (PCMs) are widely used in the thermal management of electronic devices by effectively lowering the hot end temperature and increasing the energy conversion efficiency. In this article, numerical studies were performed to understand how temperature instability during the periodic utilization of electronic devices affects the heat-dissipation effectiveness of a phase-change material heat sink embedded in an electronic device. Firstly, three amplitudes of 10 °C, 15 °C, and 20 °C for fixed periods of time, namely, 10 min, 20 min, and 40 min, respectively, were performed to investigate the specific effect of amplitude on the PCM melting rate. Next, the amplitude was fixed, and the impact of the period on heat sink performance was evaluated. The results indicate that under the 40 min time period, the averaged melting rate of PCMs with amplitudes of 20 °C, 15 °C, and 10 °C reaches the highest at 19 min, which saves 14 min, 10 min, and 8 min, respectively, compared with the constant input of the same melting rate. At a fixed amplitude of 20 °C, the PCM with a period of 40 min, 20 min, and 10 min has the highest averaged melting rate at 6 min, 11 min, and 19 min, saving the heat dissipation time of 3 min, 8 min, and 14 min, respectively. Overall, it was observed that under identical amplitude conditions, the peak melting rate remains consistent, with longer periods resulting in a longer promotion of melting. On the other hand, under similar conditions, larger amplitude values result in faster melting rates. This is attributed to the fact that the period increases the heat flux output by extending the temperature rise, while the amplitude affects the heat flux by adjusting the temperature. Full article

This study investigates the micro-mechanical behavior of mortar under uniaxial compression using a three-phase model in PFC^3D. By simulating mortar as a composite of cement, sand, and the interfacial transition zone (ITZ), the research examines the impact of particle size on stress–strain behavior, crack propagation, porosity distribution, contact forces, and energy transformation. The simulations reveal that reducing sand particle size from 1–2 mm to 0.25–0.5 mm leads to a significant increase in uniaxial compressive strength, with peak strength values rising from 65.3 MPa to 89.6 MPa. The elastic modulus similarly improves by approximately 20% as particle size decreases. The study also finds that tensile cracks dominate failure, accounting for over 95% of total cracks, with their onset occurring at lower strains as the particle size is reduced. Porosity analysis shows that smaller particles result in a more uniform distribution, with the final porosity at peak strength ranging between 0.26 and 0.29, compared to 0.22 to 0.31 for larger particles. Additionally, energy dissipation patterns reveal that as particle size decreases, the boundary energy transformation into strain energy becomes more efficient, with a 15% increase in strain energy storage observed. These findings provide critical insights into optimizing mortar microstructure for enhanced mechanical performance in construction applications. Full article

The crystal structure has a great influence on the dielectric and piezoelectric performance of poly(vinylidene fluoride) (PVDF). In this work, we prepared PVDF films with two typical crystalline phases (α and β). In situ Kelvin probe force microscopy (KPFM) and Piezoelectric force microscopy (PFM) were employed to investigate the responses of different PVDF crystalline phases to charge mobility, polarization, and piezoelectric properties. We used a homemade Kelvin probe force microscope (KPFM) to inject charges into the two crystalline phases to investigate the differences in the response of different crystalline phases of PVDF to electrical excitation on a microscopic scale. It was found that the α-phase has a lower charge injection barrier and is more susceptible to charge injection and that the α-phase is accompanied by a faster charge dissipation rate, which makes it easier to accumulate charge at the interface between the α-phase and β-phase PVDF. Moreover, the PFM polarization manipulation showed no change in the amplitude and phase diagram of the α-phase under ±10 V bias. In contrast, the β-phase showed a clear polarization reversal phenomenon and a significant increase in piezoelectric amplitude, which is consistent with its polar intrinsic properties. This study provides valuable insights into the multiphase contributions and a reference for designing advanced PVDF dielectrics. Full article

The features of rock shear-slip fracturing are closely related to the stability of rock mass engineering. Granite, white sandstone, red sandstone, and yellow sandstone specimens were selected in this study. The loading phase of “shear failure > slow slip > fast slip” was set up to explore the correlation between fracture type, acoustic emission (AE) features, and energy dissipation during the rock fracturing process. The results show that there is a strong correlation between fracture type, energy dissipation, and AE features. The energy dissipation ratio of tension-shear (T-S) composite, shear, and tensile types is 10:100:1. The fracture types in the shear failure phase are mainly tensile and TS composite types. The differential mechanism of energy dissipation of different rocks during the shear-slip process is revealed from the physical property perspectives of mineral composition, particle size, and diagenetic mode. These results provide a necessary research basis for energy dissipation research in rock failure and offer an important scientific foundation for analyzing the fracture propagation problem in the shear-slip process. They also provide a research basis for further understanding the acoustic emission characteristics and crack type evolution during rock shear and slip processes, which helps to better understand the shear failure mechanism of natural joints and provides a reference for the identification of precursors of shear disasters in geotechnical engineering. Full article

This article aims to propose a highly reliable permanent magnet synchronous machine (PMSM) for flywheel energy-storage systems. Flywheel energy-storage systems are large-capacity energy storage technologies suitable for the short-term storage of electrical energy. PMSMs have been used in the flywheel energy-storage systems due to their advantages. One of the key requirements for PMSMs in flywheel energy-storage systems is high reliability. A double redundant winding structure is adopted to ensure fault-tolerant operation of the PMSM. The stator is designed with auxiliary teeth to reduce the short-circuit current. Moreover, the number of slots and poles is determined to ensure the winding factor, heat dissipation, and reduce losses. Moreover, the dual three-phase stator winding structure and auxiliary teeth are adopted on the PMSM to improve reliability. Afterward, the electromagnetic performance is analyzed, and the mechanical stress is investigated to ensure mechanical strength. Finally, a prototype is built and tested to verify the theoretical analysis and performance of the PMSM. Full article

The hydraulic performance of pooled stepped spillways has received less recognition compared to the traditional stepped spillways. Regarding the effectiveness of pooled stepped spillways in managing flow dynamics, previous studies have focused on investigating how different step configurations and varying chute angles can enhance energy dissipation in gravity flow over the chute. However, the potential for optimal performance and the importance of proper design have not been thoroughly explored in the existing literature. This study aims to explore new configurations of pooled stepped spillways and compare them to traditional stepped spillway designs to enhance hydraulic efficiency and maximize energy dissipation. The study examines two types of configurations of stepped spillways—two flat and two pooled configurations, each with ten steps. Using the computational Fluid Dynamics (CFD) technique, such as Volume of Fluid Method (VOF) and the realizable k-ε turbulence model for two-phase flow analysis with a 26.6° chute slope. Initially, the model was validated with experimental data by comparing various hydraulic parameters. These parameters include water depth, roller length, jump length, ratio of critical depth, and sequent depth. The hydraulic performance of both stepped geometric configurations was evaluated through numerical simulations to examine how the geometries of flat and pooled stepped spillways influence flow characteristics, energy dissipation, velocity, pressure distribution, and the Froude number at the downstream. The study analyzed downstream flow characteristics, maximum energy dissipation rates, depth-averaged velocity, static pressure, and pressure contours at the lateral direction under six different flow rates in flat and pooled stepped spillways. The findings indicate that flat-step configurations exhibit lower energy dissipation compared to pooled configurations. The relative energy loss of flow on pooled steps dissipates more energy than on flat steps. Furthermore, it is observed that the pooled configurations performed better for energy dissipation and flow stability compared to the flat configurations. The energy dissipation increased in pooled stepped spillways by 34.68% and 25.81%, respectively. Additionally, the depth-averaged flow velocity and pressure distribution decreased in case 2 and case 4 compared to the flat-step configurations. Full article

Focusing on solving the adverse laser-inducing damage problem, high-power laser-resistant strategies have attracted more attention. In order to improve the laser-resistant property, a novel dynamic porous structure generation idea for laser irradiation was presented in this study, both of high-reflection and reaction endothermic effects. A detailed investigation on phase structure change, optical properties variation, micro-structure evolution, and substrate temperature development during laser irradiation was performed. The initial reflectivity of two coatings at 1064 nm was high, around 80–90%. During laser irradiation, the reflectivity grew continuously, reaching a maximum of 93%. During laser irradiation, a skeleton porous structure formed, promoted by the endothermic reaction of aluminum tri-hydroxide, whose structure contributes to the heat insulation from surface to interior. Thus, the prepared coating showed excellent anti-laser ablation performance, being dependent on its thermal insulation by the reaction-generated porous structure; high reflectivity by surface; and heat dissipation by endothermic reaction. Under 2000 W/cm², 10 s laser irradiation (spot area is 10 mm × 10 mm), the back-surface temperature is just 159 °C, which is far away from the melting point of aluminum substrate. The coatings and strategy mentioned in this study have a great potential to be applied in the anti-laser field. Full article

This paper proposes an adaptive acceleration lock compensation technology for phase-locked loops (PLLs) based on a novel dual-mode programmable ring voltage-controlled oscillator (ring-VCO). In addition, a time-to-digital converter (TDC) is designed to accurately quantify the phase difference from the phase frequency detector (PFD) in order to optimize the dead-zone effect while dynamically switching an auxiliary charge pump (CP) module to realize fast phase locking. Furthermore, a TDC-controlled three/five-stage dual-mode adaptively continuously switched VCO is proposed to optimize the phase noise (PN) and power efficiency, leading to an optimal performance tradeoff of the PLL. Based on the 180 nm/1.8 V standard CMOS technology, the complete PLL design and a corresponding simulation analysis are implemented. The results show that, with a 1 GHz reference signal as the input, the output frequency is 50–324 MHz, with a wide tuning range of 260 MHz and a low phase noise of −98.07 dBc/Hz@1 MHz. The key phase-locking time is reduced to 1.11 μs, and the power dissipation is lowered to 1.86 mW with a layout area of 66 μm × 128 μm. A significantly remarkable multiobjective performance tradeoff with topology optimization is realized, which is in contrast to several similar design cases of PLLs. Full article

To solve the problem of the oscillation stability of direct-driven wind-powered grid-connected systems with a low-voltage crossing control, a method of oscillation stability analysis for these systems, based on interactive energy, is proposed in this paper. Firstly, a dynamic energy model of a direct-driven wind-powered grid-connected system is established, considering a low-voltage traverse control. Secondly, the energy is divided into four parts—the line parameter energy, current inner loop energy, PLL energy, and current inner loop–PLL interaction energy—and the conduction path of the energy during a low-voltage crossing is described. On this basis, the aperiodic components of each energy path are analyzed, the stability level of the system is quantified, the influence of the different control parameters on the interactive energy dissipation is deduced, the key interactive control links affecting the stability of the system are screened, and the influence rules of the parameters are expounded. Finally, a direct-driven wind-powered grid-connected system model is built on the Rt-lab platform, and it is verified by a simulation test. The results show that the interaction energy generated by the interaction of the current inner loop and phase-locked loop is a key factor affecting the stability of the direct-driven wind-powered grid-connected system. The simulation test parameters of the control group were adjusted as the current inner loop’s proportion parameter increased from 1.32 to 5.28, the current inner loop’s integral parameter increased from 4.48 to 6.42, the PLL’s proportion parameter decreased from 9.45 to 6.3, and the PLL’s integral parameter decreased from 50.25 to 40.2. Both the theoretical and experimental results show that increasing the current inner loop’s integral and proportion parameters can improve the stability level of the direct-driven wind-powered grid-connected system; reducing the phase-locked loop’s proportion and integral parameters can also improve the stability level of the grid-connected system. Full article