Search Results (126)

A wavelength-swept laser (WSL) demodulation system offers a unique time-domain analysis solution for high-sensitivity optical fiber sensors, providing a high-resolution and high-speed method compared to optical spectrum analysis. However, most traditional WSL-demodulated sensing systems require a synchronous trigger signal or an additional optical dispersion link for sensing analysis and typically use a fiber Bragg grating (FBG) as the sensing unit, which limits displacement sensitivity and increases fabrication costs. We present a novel displacement sensing system that combines a trigger-free WSL demodulation method with a cascaded balloon-like interferometer, featuring a simple structure, high sensitivity, and low temperature cross-sensitivity. The sensor is implemented by bending a short length of single-mode fiber with an optimal radius of around 4 mm to excite cladding modes, which form an interference spectral response with the core mode. Experimental findings reveal that the system achieves a high sensitivity of 397.6 pm/μm for displacement variation, corresponding to 19.88 ms/μm when demodulated using a WSL with a sweeping speed of 20 nm/s. At the same time, the temperature cross-sensitivity is as low as 5 pm/°C or 0.25 ms/°C, making it a strong candidate for displacement sensing in harsh environments with significant temperature interference. Full article

In this paper we demonstrate a new approach to the measurement of dispersion of light reflected in integrated optical devices. The approach utilizes the fact that light reflected from the end facet of an integrated waveguide will interfere with light reflected from points inside the device under test (DUT), effectively creating a Michelson interferometer. The distance between the measured fringes of this interferometric signal will depend directly on the group delay experienced in the device under test, allowing for fast and easy measurement of waveguide dispersion. This approach has been used to determine the dispersion of a fabricated linearly chirped Bragg gratings waveguide and the result agrees well with the designed value. Full article

With the introduction of advanced Fiber Bragg Grating (FBG) technology, Fabry–Pérot (FP) interferometers have become widely used in fiber-optic ultrasound detection. In these applications, the slope of the reflectance is a critical factor influencing detection results. Due to the intensity limitations of the laser source in fiber-optic ultrasound detection, the reflectance of the FBG is generally increased to enhance the signal-to-noise ratio (SNR). However, increasing reflectance can cause the reflectance curve to deviate from a sinusoidal shape, which in turn affects the slope of the reflectance and introduces greater errors. This paper first investigates the relationship between the transmission curve of the FP interferometer and reflectance, with a focus on the errors introduced by simplified assumptions. Further research shows that in sensors with asymmetric reflectance slopes, their transmittance curves deviate significantly from sinusoidal signals. This discrepancy highlights the importance of achieving symmetrical slopes to ensure consistent and accurate detection. To address this issue, this paper proposes an innovative method to adjust the rear-end reflectance of the FP interferometer by combining stress modulation, UV adhesive, and a high-reflectivity metal disk. Additionally, by adjusting the rear-end reflectance to ensure that the transmittance curve approximates a sinusoidal signal, the symmetry of the slope is maintained. Finally, through practical ultrasound testing, by adjusting the incident wavelength to the positions of slope extrema (or zero) at equal intervals, the expected ultrasound signals at extrema (or zero) can be detected. This method converts the problem of approximating a sinusoidal signal into a problem of the slope adjustment of the transmittance curve, making it easier and more direct to determine its impact on detection results. The proposed method not only improves the performance of fiber-optic ultrasound sensors but also reduces costs, paving the way for broader applications in medical diagnostics and structural health monitoring. Full article

Implementation of edge-filter detection for interrogating optical interferometric ultrasonic sensors is often hindered by the lack of cost-effective laser sources with agile wavelength tunability and good noise performance. The detected signal can also be affected by optical power variations and locking-point drift, negatively affecting the sensor accuracy. Here, we report the use of laser single-sideband generation with a dual-parallel Mach–Zehnder interferometer (DP-MZI) for laser wavelength tuning and locking in edge-filter detection of fiber-optic ultrasonic sensors. We also demonstrate real-time in situ calibration of the sensor response to ultrasound-induced wavelength shift tuning. The DP-MZI is employed to generate a known wavelength modulation of the laser, whose response is used to gauge the sensor response to the ultrasound-induced wavelength shifts in real time and in situ. Experiments were performed on a fiber-optic ultrasonic sensor based on a high-finesse Fabry–Perot interferometer formed by two fiber Bragg gratings. The results demonstrated the effectiveness of the laser locking against laser wavelength drift and temperature variations and the effectiveness of the calibration method against optical power variations and locking-point drift. These techniques can enhance the operational robustness and increase the measurement accuracy of optical ultrasonic sensors. Full article

In the field of fiber-optic sensing, effectively reducing the noise of sensing spectra and achieving a high signal-to-noise ratio (SNR) has consistently been a focal point of research. This study proposes a deep-learning-based denoising method for fiber-optic sensors, which involves pre-processing the sensor spectrum into a 2D image and training with a cycle-consistent generative adversarial network (Cycle-GAN) model. The pre-trained algorithm demonstrates the ability to effectively denoise various spectrum types and noise profiles. This study evaluates the denoising performance of simulated spectra obtained from four different types of fiber-optic sensors: fiber Fabry–Perot interferometer (FPI), regular fiber Bragg grating (FBG), chirped FBG, and FBG pair. Compared to traditional denoising algorithms such as wavelet transform (WT) and empirical mode decomposition (EMD), the proposed method achieves an SNR improvement of up to $13.71 \mathrm{dB}$, an RMSE that is up to three times smaller, and a minimum correlation coefficient ($R^2$) of no less than 99.70% with the original high-SNR signals. Additionally, the proposed algorithm was tested for multimode noise reduction, demonstrating an excellent linearity in temperature response with a $R^2$ of 99.95% for its linear fitting and $99.74\%$ for the temperature response obtained from single-mode fiber sensors. The proposed denoising approach effectively reduces the impact of various noises from the sensing system, enhancing the practicality of fiber-optic sensing, especially for specialized fiber applications in research and industrial domains. Full article

This study introduces a Sagnac Interferometer (SI) fiber sensor that integrates Polarization-Maintaining Fibers (PMFs) with a Tilted Fiber Bragg Grating (TFBG) for the dual-parameter measurement of strain and lateral pressure. By incorporating a 6° TFBG with PMFs into the SI sensor, its sensitivity is significantly enhanced, enabling advanced multi-parameter sensing capabilities. The sensor demonstrates a temperature sensitivity of −1.413 nm/°C and a lateral pressure sensitivity of −4.264 dB/kPa, as validated by repeated experiments. The results exhibit excellent repeatability and high precision, underscoring the sensor’s potential for robust and accurate multi-parameter sensing applications. Full article

The unique diffractive properties of gratings have made them essential in a wide range of applications, including spectral analysis, precision measurement, optical data storage, laser technology, and biomedical imaging. With advancements in micro- and nanotechnologies, the demand for more precise and efficient grating fabrication has increased. This review discusses the latest advancements in grating manufacturing techniques, particularly highlighting laser interference lithography, which excels in sub-beam generation through wavefront and amplitude division. Techniques such as Lloyd’s mirror configurations produce stable interference fringe fields for grating patterning in a single exposure. Orthogonal and non-orthogonal, two-axis Lloyd’s mirror interferometers have advanced the fabrication of two-dimensional gratings and large-area gratings, respectively, while laser interference combined with concave lenses enables the creation of concave gratings. Grating interferometry, utilizing optical interference principles, allows for highly precise measurements of minute displacements at the nanometer to sub-nanometer scale. This review also examines the application of grating interferometry in high-precision, absolute, and multi-degree-of-freedom measurement systems. Progress in grating fabrication has significantly advanced spectrometer technology, with integrated structures such as concave gratings, Fresnel gratings, and grating–microlens arrays driving the miniaturization of spectrometers and expanding their use in compact analytical instruments. Full article

In this paper, we propose a novel approach to coordinate-based acoustic emission (AE) source localization to address the challenges of limited and imbalanced datasets from fiber-optic AE sensors used for structural health monitoring (SHM). We have developed a hybrid deep learning model combining four generative adversarial network (GAN) variants for data augmentation with an adapted inception neural network for regression-based prediction. The experimental setup features a single fiber-optic AE sensor based on a tightly coiled fiber-optic Fabry-Perot interferometer formed by two identical fiber Bragg gratings. AE signals were generated using the Hsu-Nielsen pencil lead break test on a grid-marked thin aluminum plate with 35 distinct locations, simulating real-world structural monitoring conditions in bounded isotropic plate-like structures. It is demonstrated that the single-sensor configuration can achieve precise localization, avoiding the need for a multiple sensor array. The GAN-based signal augmentation expanded the dataset from 900 to 4500 samples, with the Wasserstein distance between the original and synthetic datasets decreasing by 83% after 2000 training epochs, demonstrating the high fidelity of the synthetic data. Among the GAN variants, the standard GAN architecture proved the most effective, outperforming other variants in this specific application. The hybrid model exhibits superior performance compared to non-augmented deep learning approaches, with the median error distribution comparisons revealing a significant 50% reduction in prediction errors, accompanied by substantially improved consistency across various AE source locations. Overall, this developed hybrid approach offers a promising solution for enhancing AE-based SHM in complex infrastructures, improving damage detection accuracy and reliability for more efficient predictive maintenance strategies. Full article

A fiber Bragg grating (FBG) pulse and systolic blood pressure (SBP) measurement system based on the edge-filtering method is proposed. The edge filter is the Mach–Zehnder interferometer (MZI) fabricated by two fiber couplers with a linear slope of 52.45 dBm/nm. The developed system consists of a broadband light source, an edge filter, fiber Bragg gratings (FBGs), a coarse wavelength-division multiplexer (CWDM), and signal-processing circuits based on a field-programmable gate array (FPGA). It can simultaneously measure pulse pulsations of the radial artery in the wrist at three positions: Cun, Guan and Chi. The SBP can be calculated based on the pulse transit time (PTT) principle. The measurement results compared to a standard blood pressure monitor showed the mean absolute error (MAE) and standard deviation (STD) of the SBP were 0.93 ± 3.13 mmHg. The system meets the requirements of the Association for the Advancement of Medical Instrumentation (AAMI) equipment standards. The proposed system can achieve continuous real-time measurement of pulse and SBP and has the advantages of fast detection speed, stable performance, and no compression sensation for subjects. The system has important application value in the fields of human health monitoring and medical device development. Full article

In this study, based on the principle of grating interferometer-based acoustic sensors, design guidelines for the grating interferometric module were obtained and analyzed considering various factors in order to obtain high sensitivity, and a glass-based grating interference component and its acoustic sensor device were developed. The key parameters of the grating interference structure were extracted, and their effects on the acoustic response sensitivity were quantified for multiple mechanisms. For the development of the acoustic sensor, the grating-on-convex-platform structure and the micromachining processes of the glass-based components were designed and developed. The developed acoustic sensor samples achieved high sensitivity. In particular, the sample suitable for low-frequency application obtained a sensitivity of 0.776 V/Pa @ 1 kHz, and the spectrum of its sensitivity was flat from 50 Hz to 8 Hz with a deviation less than 1.5 dB and a sensitivity of 0.408 V/Pa @ 20 Hz. Full article

Fiber-optic sensors, such as fiber Bragg grating (FBG) sensors and fiber-optic interferometers, have excellent sensing capabilities for industrial, chemical, and biomedical engineering applications. This paper used machine learning to enhance the number of fiber-optic sensing placement points and promote the cost-effectiveness and diversity of fiber-optic sensing applications. In this paper, the framework adopted is the FBG cascading an interferometer, and a deep belief network (DBN) is used to demodulate the wavelength of the sampled complex spectrum. As the capacity of the fiber-optic sensor arrangement is optimized, the peak spectra from FBGs undergoing strain or temperature changes may overlap. In addition, overlapping FBG spectra with interferometer spectra results in periodic modulation of the spectral intensity, making the spectral intensity variation more complex as a function of different strains or temperature levels. Therefore, it may not be possible to analyze the sensed results of FBGs with the naked eye, and it would be ideal to use machine learning to demodulate the sensed results of FBGs and the interferometer. Experimental results show that DBN can successfully interpret the wavelengths of individual FBG peaks, and peaks of the interferometer spectrum, from the overlapping spectrum of peak-overlapping FBGs and the interferometer. Full article

A vector curvature and temperature sensor based on an in-fiber hybrid microstructure is proposed and experimentally demonstrated. The proposed scheme enables the dimensions of the Fabry–Perot and Mach–Zehnder hybrid interferometer to be adjusted for the formation of the Vernier effect by simply changing the length of a single optical fiber. The sensor is fabricated using a fiber Bragg grating (FBG), multimode fiber (MMF), and a single-hole dual-core fiber (SHDCF). The sensor exhibits different curvature sensitivities in four vertical directions, enabling two-dimensional curvature sensing. The temperature and curvature sensitivities of the sensor were enhanced to 100 pm/°C and −25.55 nm/m⁻¹, respectively, and the temperature crosstalk was minimal at −3.9 × 10⁻³ m⁻¹/°C. This hybrid microstructure sensor technology can be applied to high-sensitivity two-dimensional vector curvature and temperature detection for structural health monitoring of buildings, bridge engineering, and other related fields. Full article

In this paper, we demonstrated a distributed feedback fiber-laser- (DFB-FL) based ultrasound detection system with a high signal-to-noise ratio (SNR), high sensitivity and wide frequency response range. The DFB-FL was fabricated by UV-inscribing a π phase-shifted grating in the Erbium–Ytterbium co-doped fiber using the phase mask method. The theory of DFB-FL and the sensing principle has been discussed and analyzed. The sensing signal was demodulated via an unbalanced Mach–Zehnder interferometer (MZI) system. The experimental results showed that the sensitivity of the sensor reached 75.18 mV/kPa and the flat frequency response range covered over 30 MHz, which covered the ultrasonic detection frequency range of abnormal discharge in the electric power system. The SNR of this DFB-FL was 42.9 dB, and the corresponding noise-equivalent pressure was calculated as 0.12 kPa. Full article

We demonstrate fast writing of strong fiber Bragg grating (FBG) without hydrogen loading using 343 nm femtosecond pulses of only 7 $\mathsf{\mu }$J energy at 60 kHz repetition rates and a two-mask interferometer. The beam was focused to a 30–50 $\mathsf{\mu }$m diameter along the fiber axis, greatly enhancing the peak power while avoiding damage to the masks. A refractive index modulation of more than ${10}^{-3}$ could be obtained in less than one minute exposure. To avoid the observed strong temperature gradient observed in the SMF-28 fiber, a galvo scanner was used to rapidly move the beam back and forth laterally up to 1 mm. FBG were written in SMF-28, as well as 20/400 $\mathsf{\mu }$m fiber. In the latter fiber, better heat dissipation allowed us to write the FBG with the standard phase mask scanning technique, and a 0.28 mm Gaussian apodized FBG could be written. Full article

Conventional optical fiber temperature/strain sensors often have to make compromises between the resolution and the dynamic range. Here we present a new method that meets the measurement requirements for both high resolution and large dynamic range. A high-quality optical fiber Fabry-Perot Interferometer (FPI) constructed using a pair of chirped fiber Bragg gratings is employed as the sensor and a dual-mode direct spectrum interrogation method is proposed to identify the small drift of external temperature or strain. As a proof-of-concept illustration, a temperature resolution of 0.2 °C within 30–130 °C is demonstrated. For strain sensing, the resolution can be 10 µε within 0–1000 µε. The measurement resolution can be improved further by routinely increasing the reflectivity of the CFBG and the cavity length and the sensor can also be mass-produced. This new sensing schema not only resolves the conflict between the resolution and the dynamic range of fiber-optic temperature/strain sensors but can also be extended to other sensors and measurands. Full article