Search Results (2,149)

In this study, we used the depth-sensing indentation technique to determine the cracking resistance of different PVD hard coatings deposited on tool steel substrates. By comparison, with the load–displacement curves, measured at the sites of carbide inclusion and a tempered martensite matrix in the D2 tool steel substrate surface, we observed different fracture mechanisms on TiAlN hard coating prepared by sputtering. Additional information about the deformation and fracture phenomena was obtained from the SEM images of FIB cross-sections of both types of indents. We found that the main deformation mechanism in the coating is the shear sliding along the columnar boundaries, which causes the formation of steps on the substrate surface under individual columns. Using nanoindentation test, we also analyzed the cracking resistance of a set of nl-(Cr,Al)N nanolayer coatings with different Cr/Al atomic ratios, which were sputter deposited in a single batch. From the indentation curves, we determined the loads (F_c) at which the first pop-in appears and compared them with the plasticity index H³/E². A good correlation of both parameters was found. We also compared the indentation curves of the TiAlN coating, which were prepared by cathodic arc evaporation using 1-fold, 2-fold and 3-fold rotation of the substrates. Additionally, on the same set of samples, the fracture toughness measurements were performed by micro-cantilever deflection test. The impact of growth defects on the cracking resistance of the hard coatings was also confirmed. Full article

The positive effect of plasma electrolytic treatment on CrWMn tool steel to increase the wear resistance of its surface is shown. The effect of plasma electrolytic nitriding and subsequent polishing on the structure, phase and elemental composition, microhardness of the surface layer, and surface morphology is established. Steel nitriding leads to the formation of a modified surface layer including Fe_2–3N iron nitride and nitrogen martensite, below which hardening martensite is formed, reaching a microhardness value of 1200 HV. Subsequent polishing leads to a decrease in surface roughness by 42–68%. Tribological tests were carried out according to the shaft-bushing scheme. A decrease in the friction coefficient and weight wear of up to 2.6 and 30.1 times, respectively, is shown. The formed structure of the surface layer compensates for the effect of the counter body and determines the destruction of friction bonds by plastic displacement. The wear mechanism has been established and is defined as fatigue wear under dry friction and plastic contact. Full article

Wear at the male–female interface of retentive elements in implant-supported removable prostheses is the most frequent complication in such applications. The lack of an ideal/optimal insertion path, as well as the fabrication inaccuracies, are the primary contributors to this issue. A male attachment with a common ball anchor enhanced by lateral flexibility was investigated as a solution, compared to the widely used rigid ball anchor design. A parametric finite element analysis was performed to compare the wear-inducing maximum strain at the female polymer counterpart by various attachment designs made from titanium and Nitinol. The evolution of mechanical strains causing wear in the female part, as well as the contribution of stresses and martensitic transformation in the implant’s flexible shaft, were evaluated under several insertion misfit scenarios. Results indicate that introducing a long flexible shaft in the titanium implant reduced maximum strains in the female attachment part by up to 61% as compared to the solid ball anchor. Further improvement was observed by using the shape memory alloy Nitinol as shaft material, leading to a minor reduction in stress and strain at the contact surface but allowing for a shorter abutment. Finally, the optimized Nitinol implant design with a short, necked flexible shaft promoting martensitic transformation at low plateau stress resulted in an approximate 90% reduction in maximum strains at the inner surface of the female part during manual insertion, which indicates a significantly reduced wear phenomenon at the contact. Full article

Press-hardened steels (PHS), as an alternative to traditional steels and aluminum alloys, combine great mechanical performance with low manufacturing costs. PHS are martensitic steels with ultimate tensile strength (UTS) up to 2000 MPa. These steels are commonly coated with zinc-based coatings (PHS GI) consisting of multiple Zn–Fe phases to enhance corrosion resistance. However, similar to all high-strength steels, PHS are known for their elevated susceptibility to hydrogen embrittlement (HE). Absorption of atomic hydrogen into the steel lattice can lead to a transition from a ductile to a brittle fracture mechanism and decrease the stress necessary for fracture initiation. This review examines the microstructure of PHS GI with a focus on how the manufacturing process influences key parameters of the coating. The material’s susceptibility to HE is discussed in the following sections, along with the potential for hydrogen introduction through corrosion in atmospheric environments. The relationship between the content of hydrogen and its effects on fracture behavior is discussed, along with the corrosion behavior of PHS GI. The potential areas for future research and development of PHS GI with increased HE resistance are proposed. Full article

In recent years, the issue of increasing the wear resistance of the working bodies of agricultural machinery designed for cutting and breaking the soil has received special attention. The surface layers of working bodies of agricultural machinery during operation are subjected to intensive abrasive wear, which leads to rapid wear of equipment and a reduction in its service life. The induction cladding method using materials such as Sormait-1 is widely used to increase the wear resistance of tool working surfaces. However, after coating, additional heat treatment is required to improve the physical and mechanical properties of the material and increase its durability. In electrofriction technology (EFT) hardening, the surfaces of the parts are subjected to melting under the influence of electric arcs. In this work, three types of surface treatment of L53 steel have been investigated: induction cladding using Sormait-1, electrofriction treatment, and a combination of induction cladding followed by electrofriction treatment. The microstructure was analyzed using optical microscopy and scanning electron microscopy. Erosion and abrasion tests were carried out in accordance with ASTM G65 and ASTM G76-04 international standards to evaluate the wear resistance of the materials under mechanical stress. A dendritic structure was formed after the induction cladding of the Sormait-1 material, but subsequent electrofriction treatment resulted in a reduction of this dendritic structure, which contributed to an increase in the hardness of the material. However, the highest hardness, reaching 965 HV, was recorded after electrofriction treatment of L53 steel. This is explained by needle martensite in the structure, which is formed as a result of quenching. Further, the influence of structural characteristics and hardness on erosion and abrasion wear resistance was examined. The analysis showed that the material microstructure and hardness have a decisive influence on the improvement of wear resistance, especially under conditions of intensive erosion and abrasive friction. Full article

The use of a rapid heating method to achieve heterogeneity of Mn in medium-manganese steel and improve its comprehensive performance has been widely studied and these techniques have been widely applied. However, the heating rate (from α to γ) has not received sufficient attention with respect to its microstructure-evolution mechanism. In this study, the effect of heating rate on the microstructure evolution and hardness of heterogeneous medium-manganese steel was investigated by using X-ray diffraction (XRD), scanning electron microscopy (SEM), electron backscatter diffraction (EBSD), transmission electron microscopy (TEM) and DICTRA simulation. The results showed that the Mn distribution was heterogeneous in the initial microstructure of pearlite due to strong partitioning of Mn between ferrite and cementite. At low heating rates (<10 °C/s), the heterogeneity of Mn distribution was diminished to some extent due to the long-distance diffusion of Mn in high-temperature austenite. Contrastingly, at high heating rates, the initial heterogeneity of the Mn element could be largely preserved due to insufficient diffusion of Mn, which resulted in more ghost pearlite (GP: pearlite-like microstructure with film martensite/RA). Moreover, the high heating rate not only refines the prior austenite grain but also increases the total RA content, which is mainly composed of additional film RA. As the heating rate increases, the hardness gradually increases from 628.1 HV to 663.3 HV, due to grain refinement and increased dislocation density. Dynamic simulations have also demonstrated a strong correlation between this interesting microstructure and the non-equilibrium diffusion of Mn. Full article

The strength of ultra-low carbon maraging stainless steels can be significantly enhanced by precipitating nanoscale intermetallic secondary phases. Retained or reversed austenite in the steel can improve its toughness, which is key to achieving an ideal combination of strength and toughness. Ti and Al are often used as cost-effective strengthening elements in maraging stainless steels but the synergistic toughening and strengthening mechanisms of Ti and Al have not been studied. To investigate the synergistic toughening and strengthening mechanisms of Ti and Al in Co-free maraging stainless steels, this paper focuses on the microstructure and mechanical properties of three alloys: Fe-12Cr-11Ni-1.7Al-0.5Ti (Steel A), Fe-12Cr-11Ni-0.5Ti (Steel B), and Fe-12Cr-11Ni-1.7Al (Steel C). The impact of Ti and Al on the microstructure and mechanical properties was investigated using X-ray diffraction (XRD), high-resolution transmission electron microscopy (TEM), and thermodynamic simulations. The relationship between microstructure, strength, and toughness is also discussed. The results indicated that Steel A, containing both Al and Ti, exhibited the highest strength level after solution treatment at 900 °C, with an ultimate tensile strength reaching 1571 MPa after aging at 540 °C. This is attributed to the simultaneous precipitation of spherical β-NiAl and rod-shaped η-Ni₃Ti phases. Steel B, with only Ti, formed a significant amount of Ni-rich reversed austenite during aging, reducing its ultimate tensile strength to 1096 MPa. Steel C, with only Al, showed a high strength–toughness combination, which was achieved by forming dispersive nano-sized intermetallic precipitates of β-NiAl in the martensitic matrix with a slight amount of austenite. It is highlighted that Al has superior toughening and strengthening effects compared to Ti in the alloy system. Full article

The evolution of microstructures and mechanical properties with tempering temperature of a novel 2.5 GPa grade ultra-high strength steel with synergistic precipitation strengthening was investigated. With increasing tempering temperature, the experimental steel initially progressed from ε-carbides to M₃C and then to M₂C, followed by further coarsening of the M₂C carbides and β-NiAl. Concurrently, the martensite matrix gradually decomposed and austenitized. The ultimate tensile strength and yield strength initially increased and subsequently decreased with rising tempering temperature, reaching peak value at 460 and 470 °C, respectively. Conversely, the ductility and toughness initially decreased and then increased with rising tempering temperature, reaching a minimum at 440 °C. The increase in strength was attributed to the secondary hardening effects resulting from carbide evolution and the precipitation of β-NiAl. The subsequent decrease in strength was due to the recovery of martensite and coarsening of precipitates. The decrease in ductility and toughness was linked to the precipitation of M₃C, while their subsequent increase was primarily attributed to the dissolution of M₃C and an increase in the volume fraction of reverted austenite. The high dislocation density of martensite, the film of reverted austenite, nanoscale M₂C carbides, and ultrafine β-NiAl obtained during tempering at 480 °C resulted in the optimal mechanical properties of the experimental steel. The strength contributions from M₂C carbides and β-NiAl were 1081 and 597 MPa, respectively. Full article

This study provides a thorough analysis of the fatigue resistance of two low-alloy ultrahigh-strength steels (UHSSs): Steel A (fully martensitic) and Steel B (martensitic–bainitic). The investigation focused on the fatigue behaviour, damage mechanisms, and failure modes across different microstructures. Fatigue strength was determined through fully reversed tension–compression stress-controlled fatigue tests. Microstructural evolution, fracture surface characteristics, and crack-initiation mechanisms were investigated using laser scanning confocal microscopy and scanning electron microscopy. Microindentation hardness (H_IT) tests were conducted to examine the cyclic hardening and softening of the steels. The experimental results revealed that Steel A exhibited superior fatigue resistance compared to Steel B, with fatigue limits of 550 and 500 MPa, respectively. Fracture surface analysis identified non-metallic inclusions (NMIs) comprising the complex MnO-SiO₂ as critical sites for crack initiation during cyclic loading in both steels. The H_IT results after fatigue indicated significant cyclic softening for Steel A, with H_IT values decreasing from 7.7 ± 0.36 to 5.66 ± 0.26 GPa. In contrast, Steel B exhibited slight cyclic hardening, with H_IT values increasing from 5.24 ± 0.23 to 5.41 ± 0.31 GPa. Furthermore, the martensitic steel demonstrated superior yield and tensile strengths of 1145 and 1870 MPa, respectively. Analysis of the fatigue behaviour revealed the superior fatigue resistance of martensitic steel. The complex morphology and shape of the NMIs, examined using the 3D microstructure characterisation technique, demonstrated their role as stress concentrators, leading to localised plastic deformation and crack initiation. Full article

High-strength steels are widely used in various mechanical production and construction industries for their low cost, high strength and high toughness. Among these, bainitic steels have better comprehensive performance relative to martensite and ferrite. In this paper, from the point of view of its microscopic fine structure and mechanical properties, the high-carbon silicon-containing steel Fe-0.99C-1.37Si-0.44Mn-1.04Cr-0.03Ni was austenitized at high temperature after a brief isothermal treatment at 280 °C and is briefly reviewed. We have used EBSD, TEM and 3D-APT to observe a unique transformation in which high-carbon silicon-containing steels form nanostructured bainite with nanometer widths. Intriguingly, as the isothermal duration decreases, the beam bainite width becomes increasingly finer. When the beam bainite width falls below 50 nm, there is a sudden shift in defect type from the conventional edge-type dislocations to a defect characterized by the insertion of a semi-atomic surface in the opposite direction, which leads to different degrees of reduction in the micro- and macro-mechanical properties of high-carbon silicon-containing steels from 1754 MPa to 1667 MPa. This sudden change in the sub-structural properties is typical of the reverse Hall–Petch effect. Full article

Multiple phase transformations were carried out during dehydrogenation process of TiH2-based powder metallurgy. The influence of phase transformation on the microstructure is highly worthy of attention. In situ synchrotron radiation was employed to investigate the phase transformation sequence of TiH2 powder compact during the vacuum sintering process. It was found that a transformation route TiH1.971 → TiH2 + TiH + TiH0.71 + α(H) → TiH + TiH0.71 + α(H) → TiH + TiH0.71 + α(H) + β(H) → α(H) → α took place, resulting in an equiaxed microstructure. Increasing heating rate and avoiding the intense dehydrogenation to retain hydrogen-rich β (β(H)) and TiHx aciculae at the interfaces is found to be a feasible method to fabricate hierarchical α-Ti structures. A fully dense fine martensitic microstructure was produced after fast heating the TiH2 powder compact to 1100 °C and an immediate hot extrusion. Subsequently, by vacuum annealing treatment at 700 °C, composite α/βt lamellar structures were generated and a simultaneously enhanced tensile strength of 746 MPa and excellent elongation to fracture of 33.8% were achieved. It is suggested that adjusting the dehydrogenation reactions of TiH2-based powder metallurgy is conductive to generating hierarchical lamellar structures with a highly promising combination of strength and ductility for pure Ti. Full article

This paper deals with the influence of micro-pulsed direct current on microstructure and mechanical properties of gas tungsten arc welding (GTAW) weldments of Ti-6Al-4V (Ti-64). Bead-on-plate GTA welds were made on the samples in the un-pulsed and micro-pulsed (125 Hz and 250 Hz) conditions. Post-weld heat treatment (PWHT) was performed on a few coupons at 700 °C for 3 h in an inert atmosphere, followed by furnace cooling. In the microstructure, the fusion zone (FZ), base metal (BM), and heat-affected zone (HAZ) can be easily distinguished. The top surface of the FZ has large columnar grains because of lower heat loss to the surrounding atmosphere, and the bottom region of the FZ has comparatively smaller equiaxed grains. The micro-pulsed samples’ FZ grain size was lower than that of those made without pulsing. This shows that high-frequency current has substantially refined prior β grains. The microstructure of the FZ is characterized by an acicular morphology composed of α, martensitic α′, and retained β phases. The FZ’s hardness was higher than the BM due to the presence of martensitic α′. Additionally, the hardness in the HAZ was elevated due to the formation of finer martensitic α′. Micro-pulsed DC welding led to improved mechanical properties, including higher hardness, ultimate tensile strength (UTS), and ductility compared to un-pulsed welding. This enhancement is attributed to the grain refinement achieved with micro-pulsed DC. After PWHT, the prior β grain size remained relatively unchanged compared to the as-welded condition. However, the hardness in the FZ decreased due to the decomposition of α′ into α and β phases. The ductility of all samples improved as a result of the widening of the diffusional α phase. Full article

The cladding process reduces manufacturing costs by depositing super austenitic stainless steel onto low-carbon steel. Arc welding techniques, especially gas tungsten arc welding (GTAW), are commonly used for this purpose. This study evaluates the influence of heat input on cladding performance. Macroscopic analysis showed good fusion of the weld beads to the base metal with no defects. Higher heat input resulted in a lower dilution rate due to increased reinforcement. A microstructural analysis of the heat-affected zones revealed similar characteristics, with martensite formation attributed to cooling conditions. Increased microhardness was observed at the interface between the cladding and base metal, corroborating the microstructural findings. Additionally, a significant enhancement in corrosion resistance was noted in the deposited layers. This research contributes to optimizing cladding processes, ensuring better material performance in industrial applications. Full article

In the present study, the effect of the Nb element on the lattice parameters, phase stability and martensitic transformation behaviors of Ti-Zr-based shape memory alloys was extensively investigated using the first-principles calculation. The lattice parameters of both the β parent phase and α′ martensite phase gradually decreased with Nb content increasing. For the α″ martensite phase, the lattice constant (a) gradually increased with the increase in Nb content, whereas the lattice constants (b and c) continuously decreased due to the addition of Nb. Based on the formation energy and density of state, β→α′ martensitic transformation occurred, as the Nb content was not more than 12.5 at.%. However, the Ti-Zr-Nb shape memory alloys with a Nb content higher than 12.5 at.% possessed the β→α″ martensitic transformation. However, both the largest transformation strain and sensitivity of critical stress to temperature (dσ/dT) can be optimized by controlling 12.5 at.% Nb in the Ti-Zr-Nb shape memory alloy, which was favorable to obtaining the largest elastocaloric effect. Full article

P92 steel is widely used in ultra-supercritical units due to its excellent high-temperature performance. This paper studies the microstructure of P92 steel steam pipes in three conditions: as-supplied, after 80,000 h of service at 67.06 MPa stress, and after 100,000 h of service at 80.28 MPa stress. After prolonged service, the P92 steel retains its martensitic structure, but the lath width increases and the dislocation density decreases. In addition to M₂₃C₆, MX, and Laves phases, Z phase was also observed among the precipitates. The results indicate that the sizes of M₂₃C₆ and Laves phases increase with the progression of creep life consumption, with the coarsening rate of Laves phase being significantly higher than that of M₂₃C₆. However, the coarsening of MX phase is not evident. Compared to the Laves phase, the formation of the Z phase requires a longer period of time. The precipitation of the Z phase consumes MX carbonitrides, and it has been observed that the Z phase precipitates from the MX phase, with the two phases exhibiting a coexisting state. Full article