Panasonic PT-50LC14

ORDER NO.
MKE0406850C1 B2
Multi Media Display
PT-43LC14 PT-50LC14 PT-60LC14
2004 Matsushita Kotobuki Electronics Industries LTD. All rights reserved. Unauthorized copying and distribution is a violation of law.
PT-43LC14 / PT-50LC14 / PT-60LC14
CONTENTS
Page
1 SAFETY PRECAUSIONS 1.1. GENERAL GUIDELINES 1.2. LEAKAGE CURRENT COLD CHECK 1.3. LEAKAGE CURRENT HOT CHECK 1.4. UV-PRECAUTION 2 PREVENTION OF ELECTROSTATIC DISCHARGE (ESD) TO ELECTROSTATICALLY SENSITIVE (ES) DEVICES 3 ABOUT LEAD FREE SOLDER (PbF) 4 SERVICE NOTES 5 DISASSEMBLY / ASSEMBLY PROCEDURES 5.1. CABINET SECTION 6 ADJUSTMENT PROCEDURES 1 7 ADJUSTMENT PROCEDURES 2 8 TROUBLESHOOTING HINTS FOR BLOCK LEVEL REPAIR 9 BLOCK DIAGRAMS 10 SCHEMATIC DIAGRAMS NOTES 10.2. INTERCONNECTION SCHEMATIC DIAGRAM 10.3. FRONT JACK SCHEMATIC DIAGRAM 10.4. NETWORK / OPERATION / DIAGRAMS 10.5. AUDIO AMP SCHEMATIC DIAGRAM 10.6. TUNER SCHEMATIC DIAGRAM THERMISTOR 1 / THERMISTOR 2 / 13.4. ELECTRICAL REPLACEMENT PARTS LIST 70 71 72 COVER SWITCH SCHEMATIC 4 5 6 18 18 45 48 51 57 67 67 68 69 3 3 3 3 3 10.7. VOLTAGE CHART 11 CIRCUIT BOARD LAYOUT 11.1. FRONT JACK C.B.A. / NETWORK C.B.A. 11.2. AUDIO AMP C.B.A. / 11.3. TUNER C.B.A. 12 EXPLODED VIEWS 12.1. MAIN PARTS SECTION 12.2. FRONT AND BASE SECTION 12.3. DISPLAY SECTION 12.4. SCREEN SECTION 12.5. PROJECTION SECTION 12.6. TV AND TUNER SECTION 12.7. PACKING PARTS AND ACCESSORIES SECTION 12.8. OPTIONAL ACCESSORY SECTION 13 REPLACEMENT PARTS LIST 13.1. REPLACEMENT NOTES 13.2. MECHANICAL REPLACEMENT PARTS LIST THERMISTOR 1 C.B.A. / COVER SWITCH C.B.A. 76 77 79 79 80 81 83 85 86 87 88 90 90 91 92 93 96 14 SCHEMATIC DIAGRAMS FOR PRINTING WITH LETTER SIZE THERMISTOR 2 C.B.A. / OPERATION C.B.A. / 75
Page
73 75
10.1. SCHEMATIC DIAGRAM AND CIRCUIT BOARD LAYOUT
13.3. OPTIONAL ACCESSORY REPLACEMENT PARTS LIST
PT-43LC14 / PT-50LC14 / PT-60LC14
1 SAFETY PRECAUSIONS
1.1. GENERAL GUIDELINES
1. For continued safety, no modification of any circuit should be attempted. 2. Disconnect AC Plug before disassembling this unit. 3. It is advisable to use an isolation transformer in the AC supply before servicing. 4. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. 5. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers, shield, and isolation R-C combinations etc. are properly installed. 6. After servicing, be sure to restore the wires, leads, insulation barriers, shields, etc. 7. After servicing, make the leakage current checks to prevent the customer from being exposed to shock hazards. Caution: Use a separate Isolation Transformer for this unit when servicing.
not exceed 1/2 mA. In case a measurement is outside of the limits specified, there is a possibility of shock hazard, and thereceivershouldbe repaired and rechecked before it is returned to the customer.
Figure 1
1.4.
UV-PRECAUTION
1. Be sure to disconnect the AC Plug when replacing the lamp. 2. Since the lamp reaches a very high temperature during its operation, wait until it has completely cooled off when replacing the Lamp Unit. 3. The lamp emits small amounts of UV-Radiation. Avoid direct-eye contact by covering the Lamp and wearing the UV cut protective glass. 4. The high pressure lamp involves a risk of explosion.
1.2.
LEAKAGE CURRENT COLD CHECK
1. Unplug the AC cord and connect a jumper between the two prongs on the plug. 2. For physically operated power switches, turn power on. Otherwise skip step 2. 3. Measure the resistance value, with an ohmmeter, between the jumpered AC plug and each exposed metallic cabinet part on the receiver, such as screwheads, connectors, etc. When the exposed metallic part has a return path to the chassis, the readingshouldbebetween 1 M and 12 M. When the exposed metal does not have a return path to the chassis, the reading must be infinity.
1.3.
LEAKAGE CURRENT HOT CHECK
Figure 2
1. Plug the AC cord directly into the AC outlet. Do not use a isolation transformer for this check. 2. Connect a 1.5 k, 10 W resistor, in parallel with a 0.15 F capacitor, between each exposed metallic part on the set and a good earth ground, as shown in Figure 1. 3. Use an AC voltmeter, with 1 k/V or more sensitivity, to measure the potential across the resistor. 4. Check each exposed metallic part, and measure the voltage at each point. 5. Reverse the AC plug in the AC outlet and repeat each of the above measurements. 6. The potential at any point should not exceed 0.75 V RMS. A leakage current tester (Simpson Model 229 equivalent) may be used to make the hot checks. Leakage current must 3
PT-43LC14 / PT-50LC14 / PT-60LC14
2 PREVENTION OF ELECTROSTATIC DISCHARGE (ESD) TO ELECTROSTATICALLY SENSITIVE (ES) DEVICES

Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistorsandsemiconductor"chip" components. The following techniques should be used to help reduce the incidence of component damage caused by electro static discharge (ESD). 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,whichshouldbe removed for potential shock reasons prior to applying power to the unit under test. 2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly. 3. Use only a grounded-tip soldering iron to solder or unsolder ES devices. 4. Use only an antistatic solder removal device. Some solder removal devices not classified as "antistatic (ESD protected)" can generate electrical charge sufficient to damage ES devices. 5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices. 6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparableconductivematerial). 7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. CAUTION : Be sure no power is applied to the chassis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD)sufficienttodamage an ES device).
PT-43LC14 / PT-50LC14 / PT-60LC14
3 ABOUT LEAD FREE SOLDER (PbF)
PT-43LC14 / PT-50LC14 / PT-60LC14
4 SERVICE NOTES
LED INDICATIONS FOR ERROR CONDITION
Each LED indication facilitates finding the cause of the error. When an error is detected, the Lamp comes off and the LED on the front will flash.
POWER LED
TV/VIDEO
TEMP LED
LAMP LED
(Note 2) Error No.

1) 2) 3) 4) 5) 6) 7) 8) 9) 10) 11) 12) 13) 14) 15) 16) 17)
(Note 3) LAMP OFF
Error Information
Fan1, Fan2 or Fan3 stopped Lamp Cover open Temperature Sensor shorted or open (Thermistor 1 C.B.A.) Abnormal Temperature (Thermistor 1 C.B.A.) Ballast Error (abnormal Lamp or Ballast)
POWER LED
flashes orange once every 5 seconds flashes orange twice every 5 seconds -
TEMP LED
flashes once every 5 seconds flashes twice every 5 seconds -
LAMP LED
-
OSD
flashes once every 5 seconds flashes twice every 5 seconds flashes 3 times every 5 seconds flashes 4 times every 5 seconds flashes once every 5 seconds flashes twice every 5 seconds flashes 3 times every 5 seconds flashes 4 times every 5 seconds flashes 5 times every 5 seconds flashes 6 times every 5 seconds -
Ballast Error (abnormal Lamp voltage) Ballast Error (abnormal temperature) Ballast Error (other causes) Abnormal Voltage on 30 V line Abnormal Voltage on 9 V line Abnormal Voltage on 5 V line Abnormal Voltage on 3.3 V line Abnormal Voltage on -5 V line Abnormal Voltage on 6 V line Temperature Sensor shorted or open (Thermistor 2 C.B.A.) Abnormal Temperature (Thermistor 2 C.B.A.) Clogged air filter
flashes orange 5 times every 5 seconds flashes orange 6 times every 5 seconds flashes orange 7 times every 5 seconds flashes orange 8 times every 5 seconds flashes orange 9 times every 5 seconds flashes orange 10 times every 5 seconds -
flashes once every 5 seconds flashes twice every 5 seconds flashes 3 times every 5 seconds flashes 4 times every 5 seconds flashes 5 times every 5 seconds flashes 6 times every 5 seconds flashes 3 times every 5 seconds flashes 4 times every 5 seconds flashes 5 times every 5 seconds
Note: 1. When two or more errors have occurred at the same time, the LED will alternate flash patterns as shown above every 5 seconds. 2. Warning OSD appears when the air filter is clogged. 3. LAMP OFF: The LED will flash immediately after the Lamp comes off.
PT-43LC14 / PT-50LC14 / PT-60LC14
MAIN PARTS LOCATION

<Front View>
Network C.B.A.
Lamp Cover Cover Switch C.B.A.
TEMP LED LAMP LED Network C.B.A.
Optical Cover Front Cover Unit Operation C.B.A. POWER LED
<Rear View>
Projection Unit Thermal Fuse Unit Thermistor 1 C.B.A. Air Filter Fan Case Unit (Fan 1) Thermistor 2 C.B.A. Fan 3
Front Jack C.B.A. Main C.B.A.
Ballast C.B.A. Tuner C.B.A.
Air Filter Air Filter
Fan 2 LCD Drive C.B.A.
Audio Amp C.B.A.
Fan 4
Rear Cover Power C.B.A. Rear Jack C.B.A. TV/Tuner Unit
PT-43LC14 / PT-50LC14 / PT-60LC14
SERVICE MODE
In this mode, the following information can be confirmed on the screen: Service Mode (1/3) Current Lamp elapsed time The number of Lamp ON (For reference only) BKSV number read-out Service Mode (2/3) Key detection check Communication check for IIC bus and serial bus on the Main C.B.A. Total Lamp elapsed time Communication check for IIC bus on the Main C.B.A. EEPROM IC6006 version and build version (For reference only) EEPROM IC6306 version and build version (For reference only) IC6003 software version and build version (For reference only) IC6302 software version and build version (For reference only) Service Mode (3/3) IC6003 Port information IC6302 Port information Note: IC6003: Main Microcontroller on the Main C.B.A. IC6302: Sub Microcontroller on the Main C.B.A.
Service Mode Map

Enter : VOLUME DOWN button + TV/VIDEO key
(on the front) (on the remote)
(for more than 5 seconds in power off condition) Power ON

SERVICE LAMP CUR OSD LON BKSV MODE TIME 2000 O 15 CA F h N 3 B 1/3
OPERATION RENT LAMP: DISPLAY : COUNT : : 4B 7E 3D
< Service Mode (1/3) >
CH DOWN key
SERVICE IC3 5 6 TO IC7 5 0 0 T 5 0 0 0 A 0 1 4 5 L 1 MODE :1 :1 :1 :1 IR 3502 5103 6006 MTNR E F V V : : : : : : : : : 1 1 1 1 1 1 0 0 0 0 4 0 4 4 U 3 5 9 2 S 0 0 0 0 N 5 3 0 3 T 5 0 5 5
CH UP key
2 : : : : h : 0 2 0 /3 1 1 1 1 1
IC6003 IC6302
I 0 0 0 4 N 2 0 2 2
T 4 1 4 5 R 5 0 5 0
CH DOWN key
SE I P0 P1 P2 I P0 P1 P2 P3 P4 R C : : : C : : : : : V 6 0 1 1 6 0 0 1 I 0 0 0 1 3 0 0 0 1 C 0 0 0 1 0 1 0 1 E 3 0 0 1 2 0 0 0 1 MODE PORT 1110 0001 1111 PORT 1111 -1-1 0111 0111 0011 P P P P P P P P P P P 6 3 4 5 7 8 5 6 7 8 A : : : : : : : : : : : 0 0 1 1 1 1 1 1 0 0 0 0 0 1 1 1 0 0 0 1 0 1 0 0 -
CH UP key
0 0 0 1 1 0 1 0 0 0 0 1 0 1 1 1 0 1 0 0 0 0 0 1 0 0 1 1 1 1 0 1 0 0 1 0 0 0 1 1 1 0 0 0 0 1 1 1 0 1 1 3/3
CH DOWN key Exit: Power OFF. (When turning the power on again after once turning off, wait for approx. 10 seconds. Or, the unit can not be released from Service Mode.) Fig. 1-1
PT-43LC14 / PT-50LC14 / PT-60LC14
BEFORE REMOVING THE MAIN C.B.A. OR THE TV/TUNER UNIT FROM THE UNIT AT THE USERS LOCATION
Note: The TV/Tuner Unit includes the Main C.B.A. CAUTION: 1. Be sure to make a note of the CURRENT LAMP value (value A) in Service Mode (1/3):
WHEN REINSTALLING THE MAIN C.B.A. OR THE TV/TUNER UNIT INTO THE UNIT AT THE USERS LOCATION
CAUTION: 1. Set CURRENT LAMP value to original value as follows. 1) Select CURRENT LAMP in Service Mode (1/3). 2) Press the VOLUME UP/DOWN key on the remote to change to the original value (value A) that was noted before removing the Main C.B.A. or the TV/Tuner Unit at the users location.
SERVICE LAMP MODE TIME 2000 O 15 CD 6 h N 3 6 1/3
OPERATION RENT LAMP: DISPLAY : COUNT : : B0 3A 59
Value A (Changeable)
CUR OSD LON BKSV
Value A (Changeable)
<Service Mode (1/3)> Fig. 2 LAMP OPERATION TIME is stored in EEPROM on the Main C.B.A. Therefore, before removing the Main C.B.A. or the TV/Tuner Unit at the users location, make a note of the CURRENT LAMP value (value A) in Service Mode (1/3). Then, after installing the new Main C.B.A. or the TV/Tuner Unit at the users location, set the CURRENT LAMP value to the original value (value A) in Service Mode. Otherwise, OSD and LED Lamp replacement indications will be displayed at the wrong time. Note: In case it is impossible to make a note of the CURRENT LAMP value because of a defective Main C.B.A., ask the customer their daily average use and the approximate age of the current Lamp. Then, calculate the CURRENT LAMP value as follows and make a note.
<Service Mode (1/3)> Fig. 3
Service Mode Map

Enter : VOLUME DOWN button + TV/VIDEO key
(on the front) (on the remote)
(for more than 5 seconds in power off condition) Power ON

CH DOWN key
SERVICE IC3 5 6 TO IC7 5 0 0 T 5 0 0 0 A 0 1 4 5 L 1 MODE :1 :1 :1 :1 IR 3502 5103 6006 MTNR E F V V : : : : : : : : : 1 1 1 1 1 1 0 0 0 0 4 0 4 4 U 3 5 9 2 S 0 0 0 0 N 5 3 0 3 T 5 0 5 5
CH UP key
2 : : : : h : 0 2 0 /3 1 1 1 1 1
Daily average use X (hours)
Approx. age (days)
CURRENT LAMP (hours)
Note: The TOTAL value can be set to the original value in Service Mode (2/3) by similar method: Before removing the Main C.B.A. at the users location, make a note of the TOTAL value in Service Mode (2/3). Then, after installing the new Main C.B.A. at the users location, set the TOTAL value to the original value in Service Mode.
IC6003 IC6302
I 0 0 0 4 N 2 0 2 2
T 4 1 4 5 R 5 0 5 0
CH DOWN key
SE I P0 P1 P2 I P0 P1 P2 P3 P4 R C : : : C : : : : : V 6 0 1 1 6 0 0 1 I 0 0 0 1 3 0 0 0 1 C 0 0 0 1 0 1 0 1 E 3 0 0 1 2 0 0 0 1 MODE PORT 1110 0001 1111 PORT 1111 -1-1 0111 0111 0011 P P P P P P P P P P P 6 3 4 5 7 8 5 6 7 8 A : : : : : : : : : : : 0 0 1 1 1 1 1 1 0 0 0 0 0 1 1 1 0 0 0 1 0 1 0 0 -
CH UP key
0 0 0 1 1 0 1 0 0 0 0 1 0 1 1 1 0 1 0 0 0 0 0 1 0 0 1 1 1 1 0 1 0 0 1 0 0 0 1 1 1 0 0 0 0 1 1 1 0 1 1 3/3
CH DOWN key Exit: Power OFF. (When turning the power on again after once turning off, wait for approx. 10 seconds. Or, the unit can not be released from Service Mode.)
9
PT-43LC14 / PT-50LC14 / PT-60LC14
REPLACEMENT OF LAMP
Lamp Time Reset Procedure:
Be sure to reset the Lamp time to "0" after replacing the new Lamp. 1. Plug in the AC Cord, and turn on the power by pressing the POWER button. 2. Press and hold the VOLUME DOWN button on the unit and the SPLIT key on the remote together for over 5 seconds in power on condition. When the reset is finished, the display as shown in Fig. 51 appears and the LAMP LED goes out.
Lamp Replacement Procedure:

1. Press the POWER button on the remote to turn off the power. 2. Wait for about 1 minute until the cooling fan stops. Note: The lamp cooling fan will continue to operate for about 1 minute after the power is turned off. Do not unplug the AC Cord from the outlet until the fan has stopped. Avoid interrupting the power by using circuit breakers or switchable power strips. 3. After the cooling fan has stopped, unplug the AC Cord from the outlet. Note: Please wait more than one hour before replacing the lamp. [ Forced cooling function ] If you need to replace the lamp more urgently: The Projection display has a forced cooling feature. After the POWER button is turned OFF, and sometime during about the first minute of the normal cooling fan operation, press the VOLUME UP button on the unit and CH UP key on the remote at the same time for more than 5 seconds. The cooling fan will operate for about 10 minutes. (LAMP LED will flash 5 times every 5 second and POWER LED will flash red for 10 minutes.) 4. Remove the Front Cover Unit from the latches. 5. Remove the Lamp Cover by loosening the Screw.
Fig. 5-1 Note: 1. The unit will detect when the Lamps end of life is approaching and the following message will be displayed. And the LAMP indicator light will be lit when the Lamps end of life is approaching.
Lamp Cover Screw
Fig. 5-2 2. Influences of frequent lighting, continuous light use for over 24 hours, the number of times lit, the length of time between lightings, etc. may shorten lamp life. (Because of this, we recommend having a replacement lamp on hand.) WARNING: The high-pressure lamp could explode if not properly handled and lamp fragments could cause injury. Because the temperature of the lamp unit is elevated immediately after its use, touching it may cause burns. Please allow the lamp to cool before handling or replacing the lamp unit. Wear gloves and safety eyeglasses when replacing the lamp unit. If replacement of the lamp unit becomes necessary during the operation of the TV, follow the procedure to turn off the power and wait until the lamp unit cools completely. Cautions for Lamp Unit Replacement: Do not disassemble the Lamp. The lamp may be hot. Be careful when handling. Wear gloves. Under no circumstance should you touch the actual bulb. At this high operating temperature the natural oil on your finger can cause the glass to weaken where touched and the bulb can crack or explode.
10
Fig. 5-3 6. Loosen the Screw on the Lamp. Then, pull the Lamp. Note: Because the Lamp may still be hot, use caution when handling.
Lamp Screw
Fig. 5-4 7. Install the new Lamp, and tighten the Screw. 8. Install the Lamp Cover securely, and tighten the Screw. 9. Install the Front Cover Unit. Note: After replacing the Lamp, use caution to reset the Lamp time.
PT-43LC14 / PT-50LC14 / PT-60LC14
CLEANING METHOD
THE SCREEN UNIT AND THE MIRROR THE SCREEN UNIT (Lenticular Screen, Fresnel Lens) It is strongly recommended that the Lenticular Screen surface (outside) and the Fresnel Lens surface (inside) should be wiped gently with a clean, soft, dry cloth to remove the dirt. Note: 1. If the dirt cannot be removed by wiping with a clean, soft, dry cloth, use a clean, soft, dry cloth moistened with diluted neutral pH liquid cleanser or a lens cleaner (usually containing a small amount of ethyl alcohol) and wipe lightly. Take care not to leave any streaks. Do not use cleaning materials containing methyl alcohol, acetone, or dichloromethane. 2. Use an air blower to clean the inner surface of the Lenticular Screen and the outer surface of the Fresnel Lens (the surfaces that one another). These surfaces must not be wiped with a cloth. THE MIRROR Remove any dirt with an air blower or wipe with a clean, soft, dry cloth. If wiped too forcefully, the surface of the Mirror can be damaged. If wiping with a clean, dry cloth does not remove the dirt, the Mirror must be replaced.
Mirror
THE FILTER ON THE PROJECTION UNIT CAUTION: Operating with torn or damaged Air Filter may cause damage to the Projection unit. Remove the Projection Unit from rear. Then, clean the filters on the Projection Unit. Gently remove any accumulated dust from filter with a vacuum cleaner.
Air Filter
Screen Unit
<Bottom View>
Fig. 6-3 THE PROJECTION LENS Use lens cleaning paper and cleaner available at your local camera shop, etc. Dampen the cleaning paper with cleaner and gently wipe the surface of the lens from the center outward to remove dust. Lens
Lenticular Screen surface (outside)
Fresnel Lens surface (inside)
Fig. 6-1 THE LAMP Gently wipe the surface of the glass of the Lamp with cleaning paper or soft cloth.
Surface of glass
Fig. 6-4 THE POLARIZER UNIT, THE FIELD LENS, THE RELAY LENS, THE CONDENSER LENS, THE DICHROIC MIRROR, THE FULL MIRRORS, THE INTEGRATOR AND THE P/S CONVERTER Make sure that no dust gets on the optical components such as the Polarizer Unit, the Field Lens, the Relay Lens, the Condenser Lens, the Dichroic Mirror, the Full Mirrors, the Integrator and the P/S Converter. Clean these optical components with cleaning paper moistened with pure ethyl alcohol or a lens cleaner which contains no water or oil. THE LCD PANEL OF THE LCD/PRISM UNIT 1) Clean the surface of the LCD Panel of the LCD/Prism Unit with an air blower or wipe with a clean, or soft blush lightly. 2) If any dirt remains, lightly wipe the surface with a cotton swab moistened with pure ethyl alcohol or a lens cleaner which contains no water or oil. Use a new swab after each wiping so that dirt will not be re-deposited on the surface.
11
Fig. 6-2
PT-43LC14 / PT-50LC14 / PT-60LC14
TO DISTINGUISH THE PROJECTION LENS UNIT OR THE PROJECTION UNIT

The only difference between the 43 inch model and the 50 inch model of the Projection Unit is the Projection Lens. To distinguish, see marking (Z or A) on the Projection Lens. And the 60 inch model of the Projection Unit is placed label on the Projection Lens.
43/50 inch model as shown
RESET USERS MEMORY FUNCTIONS

Be sure to reset the users memory: After replacing the Main C.B.A. (included in the TV/Tuner Unit) If the secret code of V-chip is forgotten. When moving the unit to a new location. 1. Turn on the power. 2. Press the MENU key on the remote to display the MENU screen. 3. Select LOCK by pressing CH UP/DOWN key on the remote. Then, press the OK key.
X X X A
Z or A
4. Press and hold the VOLUME DOWN button on the unit and the OK key on the remote for more than 5 seconds while this LOCK menu is displayed. When reset is finished, power shuts off automatically (the users memory is reset).
<Front View> Z with red: for 43 inch model A with black: for 50 inch model 60 inch model as shown
CLOGGED AIR FILTER DETECTION

When a dirty or clogged air filter is detected, the OSD display appears for 1 minute. And then the Lamp is turned OFF. When this OSD display appears, remove the Projection Unit from rear, and clean the air filters gently on the Projection Unit.
AIR FILTER CLEANING IS RECOMMANDED AT THIS TIME. FIRST TURN THE UNIT OFF. PLEASE CALL FOR SERVICE. UNIT WILL BE TURNED OFF AFTER 1 MINUTE.
LSDL0248
<Front View> LSDL0248 with Yellowish green label: for 60 inch model
Note: LSDL0248 is not the part numbers of the Projection Lens as a replacement part.
12
PT-43LC14 / PT-50LC14 / PT-60LC14
BEFORE REMOVING THE PROJECTION UNIT FROM THE UNIT AT THE USERS LOCATION
1. When removing the Projection Unit, remove the Lamp from the Projection Unit and keep it. Then, reinstall this Lamp into the new Projection Unit. 2. When removing the Projection Unit, remove the Fan 3 Unit, the Top Duct 3 Unit and the 20-pin Cable from the Projection Unit and keep them. Then, reinstall the Fan 3 Unit, the Top Duct 3 Unit and the 20-pin Cable into the new Projection Unit.
21 Projection Unit
DO NOT UNPLUG AC CORD DURING COOLING OPERATION

The lamp cooling fan will continue to operate for approximately 1 minute after the power is turned off. At the same time, the POWER LED will flash red. Do not disconnect the AC Cord from the power outlet and do not open any circuit breakers while the cooling fan is still operating.
HOT CIRCUIT
Primary circuit exists on the Audio Amp C.B.A., the Ballast C.B.A. and the Power C.B.A. This circuit is identified as "HOT" on the C.B.A. and in the Service Manual. Use extreme care to prevent accidental shock when servicing.
Screw for lamp
Lamp
Clamper
Fan 3 Unit
MODEL NO. IDENTIFICATION MARK

Use Marks shown in the chart below to distinguish the different models included in this Service Manual.
P2904
402
MODEL
GND Wire
MARK A B C PT
421
402
PT-43LC14 PT-50LC14 PT-60LC14 NOT USED
421
Top Duct 3 Unit
Note: Refer to Item 3 of Schematic Diagram Notes of Schematic Diagram and Circuit Board Layout Notes, for mark "PT."
13
PT-43LC14 / PT-50LC14 / PT-60LC14
WIRE AND LEAD POSITION DIAGRAM OF THE UNIT
After servicing, make sure that all wires, leads, and clampers are placed in their original position. It is important for the best operation of the unit. Note: Use extreme care especially for the following.
Clamper Clamper RF Input Terminal Thermal Fuse Unit
Fan 3
GND Wire AC Cord

Fig. 9-1
14
PT-43LC14 / PT-50LC14 / PT-60LC14
P2303 (From Thermistor 1 C.B.A.)
Thermistor 2 C.B.A.
P2902 (From Fan 1) Lamp Cable
Lamp Sockets
P2501 (From Main C.B.A.)
P2901 (From Main C.B.A.)
P2904 (From Fan 3)
P2502 (From Cover Switch C.B.A.)
Clamper P2304 (From Thermistor 2 C.B.A.)
P2903 (From Fan 2)
Clamper Fan 4
Ballast C.B.A. P1306 (From Thermal Fuse Unit)

Fig. 9-2
15
PT-43LC14 / PT-50LC14 / PT-60LC14
After servicing, make sure that all wires, leads, and clampers are placed in their original position. It is important for the best operation of the unit. Note: Use extreme care especially for the following. P6305 (From Operation C.B.A.) No connection
Speaker Connector Leads
P5501 (From Front Jack C.B.A.)
P6004 (From Tuner C.B.A.)
Clampers
P3501 (From Tuner C.B.A.)
P3502 (From Front Jack C.B.A.) P4505 (To Tuner C.B.A.) P4501 (From Power C.B.A.) Clamper P6002 (From Ballast C.B.A.) GND Plate A P3401 (From Power C.B.A.) Clamper P3504 (From Front Jack C.B.A.) P3603 (From Audio Amp C.B.A.)
P4503 (From Speaker)
P3402 (From LCD Drive C.B.A.) P5302 (From LCD Drive C.B.A.)
P805 (From Ballast C.B.A.) Clamper
20-pin Cable
Connector Cable Fig. 9-3
16
PT-43LC14 / PT-50LC14 / PT-60LC14
P1001 (To Ballast C.B.A.)
P3401 (To Main C.B.A.)
P805 (To Ballast C.B.A.)
Clamper P4501 (To Audio Amp C.B.A.) P1009 P1010 P1011
P1007
Clamper
P804 P1006 (To Fan 4) AC Cord

Fig. 9-4
17
PT-43LC14 / PT-50LC14 / PT-60LC14
5 DISASSEMBLY / ASSEMBLY PROCEDURES

5.1. CABINET SECTION
CABINET SECTION
DISASSEMBLY METHOD OF CABINET SECTION
Cabinet section contains following removal procedures:
REMOVAL OF THE BALLAST C.B.A. AND THE TV/TUNER UNIT FROM THE CABINET REMOVAL OF THE PROJECTION UNIT FROM THE CABINET REMOVAL OF THE TUNER C.B.A., THE MAIN C.B.A., THE REAR JACK C.B.A., THE AUDIO AMP C.B.A., THE POWER C.B.A. FROM THE TV/TUNER UNIT REMOVAL OF THE SCREEN UNIT AND THE SPEAKER FROM THE DISPLAY REMOVAL OF THE MIRROR FROM THE BACK COVER REMOVAL OF THE FRONT JACK C.B.A. AND THE OPERATION C.B.A. FROM THE CABINET REMOVAL OF THE COVER SWITCH C.B.A. FROM THE CABINET
DISASSEMBLY FLOWCHART
This flow chart indicates the disassembly steps of the cabinet parts and the P.C.Boards in order to gain access to item (s) to be serviced. When reassembling, perform the step (s) in the reverse order. Bend, route and dress the wires as they were originally.
REAR COVER LAMP COVER FRONT COVER UNIT SPEAKER
OPTICAL COVER NETWORK C.B.A.
PROJECTION UNIT BALLAST C.B.A. THERMISTOR 2 C.B.A. FAN 3 UNIT
SCREEN UNIT
MIRROR
OPERATION C.B.A.
TV/TUNER UNIT TUNER C.B.A.
THERMAL FUSE UNIT
TOP DUCT 3 UNIT
BACK PANEL (DISPLAY)
FRONT JACK C.B.A. MAIN C.B.A. AUDIO AMP C.B.A. REAR JACK C.B.A.
POWER C.B.A.
THERMISTOR 1 C.B.A. (LCD/PRISM UNIT, LIGHT IN POLARIZER, ETC) COVER SWITCH C.B.A.
Note : a. Place a cloth or some other soft material under the P.C. Boards or Unit to prevent damage. b. When reinstalling, ensure that the connectors are connected firmly and electrical components have not been damaged. c. Do not supply power to the unit during disassembly and reassembly.
18
PT-43LC14 / PT-50LC14 / PT-60LC14
REMOVAL OF THE BALLAST C.B.A. AND THE TV/TUNER UNIT FROM THE CABINET
1. (PT-43LC14/PT-50LC14) Remove the Rear Cover by removing the 18 Screws (401).
Rear Cover
401
Fig. D1-1-1 1. (PT-60LC14) Remove the Rear Cover by removing the 20 Screws (401, 464).
Rear Cover
401
464
Fig. D1-1-2
19
PT-43LC14 / PT-50LC14 / PT-60LC14
2. Remove the Rear Support Plate by removing the 4 Screws (401, 452).
Rear Support Plate

401
401
Fig. D1-2
452
20
PT-43LC14 / PT-50LC14 / PT-60LC14
3. 1) 2) 3) 4) 5)
Remove the 5 Screws (402) and remove Clamper-1. Remove the 2 Screws (451) on the Lamp Socket. Disconnect the Lamp Connector. Avoiding the Ballast C.B.A., disconnect Connector P1306 (Thermal Fuse Unit) inside of the Ballast C.B.A. Remove the Clamper from the Ballast C.B.A.
Clamper-1
402
Lamp Socket
451
Lamp Connector Note: Do not remove the Thermal Fuse Unit. Ballast C.B.A. Clamper-1
451
Clamper
P1306
Fig. D1-3
402
Replacement Note of Ballast C.B.A.: These parts will be necessary when replacing the Ballast C.B.A. Set aside, and keep and re-use. The Clamper on Ballast C.B.A. The Thermal Fuse Unit
21
PT-43LC14 / PT-50LC14 / PT-60LC14
4. 1) Disconnect Connector P2901 (Connector Cable) and release them from the clamper. 2) Disconnect Connector P2501 (20-pin Cable) and release it from the clamper. CAUTION: Take extreme care not to damage the 20-pin Cable when disconnecting. 5. 1) Disconnect Connectors P3502, P3504, P5501, P4503, P6305 and release them from the clampers. 2) Remove the Screw (452) on the GND Plate A. 3) Remove the Screw (401) on the TV/Tuner Assy. 4) Lift up and slide the TV/Tuner Assy by releasing the 7 Guide Tabs. CAUTION: Do not slide the TV/Tuner Unit before removing the 20-pin Cable.
GND Plate A
452
P2501 P2901 Clamper
P5302
CAUTION: 20-pin Cable

P5501 P6305
Connector Cable
452
TV/Tuner Ass'y P4503 P3504 P3502 Clampers

401
Fig. D1-4
Slot holes
holes
TV/Tuner Ass'y
Guide Tabs (X5)
Guide Tabs (X2)
Rear <Bottom View of TV/Tuner Ass'y>

Fig. D1-5 Replacement Note of TV/Tuner Unit: These parts will be necessary when replacing the TV/Tuner Unit. Set aside, and keep and re-use. 20-pin Cable
22
PT-43LC14 / PT-50LC14 / PT-60LC14
6. 1) Pull off the TV/Tuner Assy with the Ballast C.B.A. while taking care with the cables. 2) Remove the GND Plate A from the TV/Tuner Unit by removing the Screw (452). 3) Remove the SD Door Unit from the TV/Tuner Unit by releasing the 2 Locking Tabs.
holes Locking Tabs Slide SD Door Unit
Ballast C.B.A.
GND Plate A
452
TV/Tuner Unit
Fig. D1-7-1 Reassembly Note: When installing the SD Door Unit, install the SD Door Unit with the 2 Locking Tabs from the front of the cabinet after installing the TV/Tuner Unit into the cabinet.
Reassembly Note: Locking Tabs SD Door Unit <Front View>

Fig. D1-7-2
Replacement Note of TV/Tuner Unit: These parts will be necessary when replacing the TV/Tuner Unit. Set aside, and keep and re-use. The GND Plate A The SD Door Unit
23
PT-43LC14 / PT-50LC14 / PT-60LC14
7. 1) Disconnect Connectors P6002, P805, P1001 and release them from the clampers. 2) Then, remove the Ballast C.B.A.
P6002 Clamper P1001 Clamper P805

Fig. D1-8
Ballast C.B.A.
24
PT-43LC14 / PT-50LC14 / PT-60LC14
REMOVAL OF THE PROJECTION UNIT FROM THE CABINET

1. Remove the Ballast C.B.A. and the TV/Tuner Unit. Refer to Steps 1~6 in "REMOVAL OF THE BALLAST C.B.A. AND THE TV/ TUNER UNIT FROM THE CABINET." 2. 1) Disconnect Connector P2502. Then, hook the P2502 cable to the pin. 2) Remove the 7 Screws (401) on the Projection Unit. 3) Lift up and slide the Projection Unit by releasing the 5 Guide Tabs. Tips on removal of the Projection Unit: First, slide the Projection Unit to the rear (approx. 1.5 inch (4 cm)). Then, lift up the front and the rear portions of the Projection Unit by both hand to release the Guide Tabs. Then, slide out the Projection Unit. Or, remove the Fan 3 Unit from the Projection Unit at first. Refer to Fig. D2-3.
CAUTION: Disconnect Connector P2502 and hook it as follows. P2502 Pin Cable
Cover Switch C.B.A. Boss
Tips on removal of the Projection Unit
Slide
4 1 3 2
P2502
Up
<Side View>
by approx. 1.5 inch (4 cm).
Up
1 Lift up and slide the Projection Unit 2 2 Lift up the front portion. 3 Lift up the rear portion. 4 Slide out the Projection Unit.
Up
Up
401
Fig. D2-1
25
PT-43LC14 / PT-50LC14 / PT-60LC14
CAUTION: Disconnect Connector P2502 and hook it as follows. P2502 Pin Cable
Guide Tabs (X5)
Cover Switch C.B.A.
<Bottom View of Projection Unit>
Rear
Projection Unit Slide
holes
Fig. D2-2 Reassembly Note: Before installing the Projection Unit, confirm that the P2502 cable is hooked to the pin. Then, install the Projection Unit to the cabinet.
26
PT-43LC14 / PT-50LC14 / PT-60LC14
3. 1) Disconnect Connector P2904, and remove the Fan 3 Unit by removing the 2 Screw (402). 2) Remove the Top Duct 3 Unit by removing the 4 Screws (421). CAUTION: When removing the Screws (421) on the Top Duct 3 Unit, plastic dust may be produced. Therefore, confirm that there is no dust on the Top Duct 3 Unit. If there is dust, clean the Top Duct 3 Unit with a brush, etc. Otherwise, dust may adhere to the inside of the screen. 3) Remove the Lamp from the Projection Unit by loosening the Screw.
21 Projection Unit
Screw for lamp
Lamp
Clamper
Fan 3 Unit
P2904
402
GND Wire
421
402
421
Fig. D2-3
Top Duct 3 Unit
Replacement Note of Projection Unit (Ref. No. 21): These parts will be necessary when replacing the Projection Unit (Ref.No. 21). Set aside, and keep and re-use. Fan 3 Unit Top Duct 3 Unit
27
PT-43LC14 / PT-50LC14 / PT-60LC14
REMOVAL OF THE TUNER C.B.A., THE MAIN C.B.A., THE REAR JACK C.B.A., THE AUDIO AMP C.B.A., THE POWER C.B.A. FROM THE TV/TUNER UNIT
CAUTION: 1. Be sure to make a note of the CURRENT LAMP value (value A) in Service Mode (1/3): LAMP OPERATION TIME is stored in EEPROM on the Main C.B.A. Therefore, before removing the Main C.B.A. or the TV/Tuner Unit at the users location, make a note of the CURRENT LAMP value (value A) in Service Mode (1/3). Then, after installing the new Main C.B.A. or the TV/Tuner Unit at the users location, set the CURRENT LAMP value to the original value (value A) in Service Mode. Otherwise, OSD and LED Lamp replacement indications will be displayed at the wrong time. Note: In case it is impossible to make a note of the CURRENT LAMP value because of a defective Main C.B.A., ask the customer their daily average use and the approximate age of the current Lamp. Then, calculate the CURRENT LAMP value as follows and make a note. Daily average use Approx. age CURRENT LAMP X = (hours) (days) (hours) 1. Remove the TV/Tuner Unit and the Ballast C.B.A. Refer to Steps 1~7 in "REMOVAL OF THE BALLAST C.B.A. AND THE TV/ TUNER UNIT FROM THE CABINET." 2. 1) Disconnect Connectors P6004, P3501 and release from the clampers. 2) Remove the Tuner C.B.A. by removing the 4 Screws (402).
TV/Tuner Unit
402
Tuner C.B.A.
P6004
Clampers
Fig. D3-1
P3501
28
PT-43LC14 / PT-50LC14 / PT-60LC14
3. 1) 2) 3) 4) 5)
Disconnect Connector P3401 and release from the clamper. Disconnect Connector P3402 and remove the Connector Cable. Remove the Tuner P.C.B. Frame by removing the 6 Screws (402). Release the AC Cord from the slot of the Rear Jack Holder. Remove the Rear Jack Holder by removing the 4 Screws (402).
402
Tuner P.C.B. Frame
Connector Cable
P3401
P3402
402
Rear Jack Holder
Slot
AC Cord
Clamper
402 402
Fig. D3-2
29
PT-43LC14 / PT-50LC14 / PT-60LC14
4. Remove the Main C.B.A. by removing the 6 Screws (402) and disconnecting Connector P3403 and P3404.
402
Main C.B.A.
P3404 P3403
Fig. D3-3
30
PT-43LC14 / PT-50LC14 / PT-60LC14
5. 1) Disconnect Connector P3603 and release from the clamper. 2) Remove the Rear Jack C.B.A. and the GND Plate C from the slots by removing the 2 Screws (402).
Slots
Rear Jack C.B.A. GND Plate C
P3603
402
Fig. D3-4 6. 1) Disconnect Connector P4501 and release from the clamper. 2) Remove the Audio Amp C.B.A. by removing the 4 Screws (402). Note: The Audio Amp C.B.A. can be removed from the TV/Tuner Unit at any time.
Audio Amp C.B.A.

402
402
Clamper P4501
Fig. D3-5
31
PT-43LC14 / PT-50LC14 / PT-60LC14
7. 1) 2) 3) 4)
Disconnect Connector P1006 and release from the clamper. Remove the Main P.C.B. Frame by removing the 6 Screws (402), and remove the Fan 4 by removing the 2 Screws (435). Remove the Power C.B.A. by removing the 5 Screws (411). Disconnect Connector P804 (AC Cord) and release from the clamper.
402
Fan 4 Clamper
435
Main P.C.B. Frame
Air Flow
Name Plate
402
411
Power C.B.A.
Clampers P804
AC Cord
P1006
411
Fig. D3-6 Reassembly Note for Fan 4: Install the Fan 4 with the 2 Screws (435) so that the name plate (manufactures name etc.) face out (visible from the outside).
Note: After servicing the Power C.B.A., be sure to connect the Connector P1006 on the Power C.B.A. to install the Fan 4.
32
PT-43LC14 / PT-50LC14 / PT-60LC14
REMOVAL OF THE SCREEN UNIT AND THE SPEAKER FROM THE DISPLAY
1. 1) Remove the Front Cover Unit from the 8 latches. 2) Remove the Optical Cover by removing the 2 Screws (454). 3) Remove the 2 Screws (401) from front side.
latches
Optical Cover
454
401
latches
401 454
Front Cover Unit

Fig. D4-1 2. (PT-43LC14/PT-50LC14) Remove the Rear Cover by removing the 18 Screws (401), refer to Fig. D1-1-1. (PT-60LC14) Remove the Rear Cover by removing the 20 Screws (401, 464), refer to Fig. D1-1-2.
33
PT-43LC14 / PT-50LC14 / PT-60LC14
3. 1) Disconnect Connector P4503 (speaker cables) and release it from the clamper. 2) Remove the 2 Screws (401) from rear side, and remove the Display.
Display
401
401
P4503 Clamper
Fig. D4-3
34
PT-43LC14 / PT-50LC14 / PT-60LC14
4. 1) Remove the Speaker-L and the Speaker-R by removing the 6 Screws (477, 478) and disconnect the connectors P4553. 2) (PT-43LC14/PT-50LC14) Remove the Screen Unit by removing the 16 Screws (401).
Screen Unit
Speaker L
401 477
P4553
477 478 401
Speaker R
P4553
477
Fig. D4-4-1
478 477
35
PT-43LC14 / PT-50LC14 / PT-60LC14
2) (PT-60LC14) Remove the Screen Unit by removing the 26 Screws (401).
Screen Unit
Speaker L
401 477
P4553
478 401
477
Speaker R
P4553
477
Fig. D4-4-2
478 477
36
PT-43LC14 / PT-50LC14 / PT-60LC14
5. (PT-43LC14) Remove the 2 Screen Plate H and 2 Screen Plate V by removing 26 Screws (401), and remove the Fresnel Lens and the Lenticular Screen. (PT-50LC14) Remove the 2 Screen Plate H and 2 Screen Plate V by removing 30 Screws (401), and remove the Fresnel Lens and the Lenticular Screen.
Screen Unit
Escutcheon
Screen Lenticular Plate H Screen Fresnel Lens Screen Plate V
401
Serial No. Label Screen Plate V
401
Screen Plate H
Front Serial No. Label of Lenticular Screen Serial No. Label of Fresnel Lens
Fig. D4-5-1 Reassembly Note: Install them so that Serial No. Labels are on the each outside as shown above. Replacement Note for Screen Unit: The Screen Unit is supplied as a unit, or the individual parts (Fresnel Lens, Lenticular Screen) in the Screen Unit are also supplied. When replacing the Fresnel Lens and the Lenticular Screen, take care that dust, etc., does not adhere between the Fresnel Lens and the Lenticular Screen. Due to this risk, it is strongly recommended to replace the Screen Unit as a unit.
37
PT-43LC14 / PT-50LC14 / PT-60LC14
(PT-50LC14) Reassembly Note for 4 Spacers: Wind the string for screen spacer on the Fresnel Lens a shown.
Fresnel Lens
string for screen spacer
Serial No. Label string for screen spacer hook string for screen spacer hook
knot hook hook
38
PT-43LC14 / PT-50LC14 / PT-60LC14
(PT60LC14) Remove the 2 Screen Plate H and 2 Screen Plate V by removing 40 Screws (465), and remove the Fresnel Lens and the Lenticular Screen.
Screen Unit
Lenticular Screen
Screen Fresnel Spacer Plate H Lens Screen Plate V
Escutcheon Spacer Spacer
465
Serial No. Label Spacer
465
Screen Plate V
Screen Plate H
Front Serial No. Label of Lenticular Screen Serial No. Label of Fresnel Lens
Spacer
Fig. D4-5-2 Reassembly Note: Install them so that Serial No. Labels are on the each outside as shown above. Replacement Note for Screen Unit: The Screen Unit is supplied as a unit, or the individual parts (Fresnel Lens, Lenticular Screen) in the Screen Unit are also supplied. When replacing the Fresnel Lens and the Lenticular Screen, take care that dust, etc., does not adhere between the Fresnel Lens and the Lenticular Screen. Due to this risk, it is strongly recommended to replace the Screen Unit as a unit.
39
PT-43LC14 / PT-50LC14 / PT-60LC14
(PT-60LC14) Reassembly Note for 4 Spacers: Place the 4 Spacers on the Lenticular Screen as shown.
Approx. 1330.5 mm ~ 1332.0 mm 11.0 mm ~ 12.5 mm 18.5 mm 2.0 mm Spacer

2.5 mm 1.5 mm
11.0 mm ~ 12.5 mm 18.5 mm 2.0 mm Spacer

2.5 mm 1.5 mm
Lenticular Screen
Lenticular Screen
Edge of Escutcheon Spacer 2.5 mm 1.5 mm
Edge of Escutcheon Spacer 2.5 mm 1.5 mm
Escutcheon
Approx. 725.5 mm ~ 754.0 mm
Lenticular Screen Spacer
Spacer
2.5 mm 1.5 mm Edge of Escutcheon
2.5 mm 1.5 mm Edge of Escutcheon
Spacer
2.5 mm 1.5 mm
Lenticular Screen Touch the bosses
Serial No. Label
2.5 mm 1.5 mm
Lenticular Screen Touch the boss
Spacer 18.5 mm 2.0 mm 11.0 mm ~ 12.5 mm
Spacer 18.5 mm 2.0 mm 11.0 mm ~ 12.5 mm
Approx. 1330.5 mm ~ 1332.0 mm
40
PT-43LC14 / PT-50LC14 / PT-60LC14
REMOVAL OF THE MIRROR FROM THE BACK COVER

(PT-43LC14/PT-50LC14) 1. Remove the Screen Unit. Refer to Steps 1~4 in "REMOVAL OF THE SCREEN UNIT AND THE SPEAKER FROM THE DISPLAY." 2. 1) Remove the 2 Mirror Holder H and the 2 Mirror Holder V Unit by removing the 12 Screws (401). 2) Remove the Mirror from the top by releasing the Back Cover slots. Note: Be careful that the Mirror does not fall down when removing.
Mirror Holder H Back Cover slots
401 401
401 401
Mirror Holder V Unit

Fig. D4-6-1 Reassembly Notes for Mirror: Install the Mirror as following procedures: 1) Place the 3 sheets on the top and bottom edges of the Mirror.
(PT-43LC14)
0 mm ~ 5 mm Sheet Sheet 0 mm ~ 5 mm 60 mm 10 mm Sheet
(PT-50LC14)
Sheet 60 mm 10 mm
Top edge of Mirror
10 mm ~ 15 mm
10 mm ~ 15 mm
10 mm ~ 15 mm
10 mm ~ 15 mm
Sheet
15 mm ~ 20 mm
15 mm ~ 20 mm
15 mm ~ 20 mm
Mirror surface
Mirror surface
15 mm ~ 20 mm
Sheet Bottom edge of Mirror
3 mm
5 mm
Sheet
3 mm
5 mm
20 mm
5 mm
Sheet
20 mm
5 mm
<Front View>
<Front View>
Fig. D4-7-1 2) Hold the sheet portions of the Mirror, and insert the Mirror from the top into the Back Cover slots carefully. When handling the Mirror, do not touch the Mirror surface. 3) Install the 2 Mirror Holder H and the 2 Mirror Holder V on the Mirror and tighten the 12 Screws (401).
41
PT-43LC14 / PT-50LC14 / PT-60LC14
REMOVAL OF THE MIRROR FROM THE BACK COVER

(PT-60LC14) 1. Remove the Screen Unit. Refer to Steps 1~4 in "REMOVAL OF THE SCREEN UNIT AND THE SPEAKER FROM THE DISPLAY." 2. 1) Remove the 3 Mirror Holder H and the 2 Mirror Holder V Unit by removing the 15 Screws (401). 2) Remove the Mirror from the top by releasing the Back Cover slots. Note: Be careful that the Mirror does not fall down when removing.
Mirror Holder H Back Cover slots
401
Mirror Holder V Unit
401
Fig. D4-6-2 Reassembly Notes for Mirror: Install the Mirror as following procedures: 1) Place the 3 sheets on the top and bottom edges of the Mirror.
10 mm ~ 20 mm
10 mm ~ 15 mm
Sheet
Sheet
Sheet
10 mm ~ 20 mm
10 mm ~ 15 mm
Top edge of Mirror
Sheet
15 mm ~ 20 mm
Mirror surface
15 mm ~ 20 mm
Sheet Bottom edge of Mirror
18 mm ~ 28 mm
Sheet <Front View>
18 mm ~ 28 mm
Fig. D4-7-2 2) Hold the sheet portions of the Mirror, and insert the Mirror from the top into the Back Cover slots carefully. When handling the Mirror, do not touch the Mirror surface. 3) Install the 3 Mirror Holder H and the 2 Mirror Holder V on the Mirror and tighten the 15 Screws (401).
42
PT-43LC14 / PT-50LC14 / PT-60LC14
REMOVAL OF THE FRONT JACK C.B.A. AND THE OPERATION C.B.A. FROM THE CABINET
1. 1) 2) 2. 1) 2) 3) 4) 5) Remove the Rear Cover by removing the 18 Screws or 20 Screws (PT-60LC14). Disconnect Connector P6305 and release it from the clamper. Remove the Front Cover Unit from the 8 latches. Remove the Screw (454). Slide the Front Side Cover R with the Operation C.B.A. as indicated by the arrow to release the 4 slots. Pull off the Operation C.B.A. from front side. Remove the Operation C.B.A. and the Operation Button Unit from the Front Side Cover R by removing the 4 Screws (421).
slots
Operation Operation Button Unit C.B.A. 421
P6305 Slide
421
Bosses Front Cover Unit

3. 1) 2) 3) 4)
Clampers <Rear View>
454 Front Side
Cover R
Fig. D5-1
Disconnect Connectors P3502, P3504, P5501 and release them from the clampers. Remove the 2 Screw (401). Pull off the Front Jack C.B.A. from front side. Remove the Front Jack C.B.A. from the Side Jack Holder by removing the 2 Screws (421) and releasing the 2 Locking Tabs.
Front Jack C.B.A.

421
P5501
Boss Locking Tabs Side Jack Holder

Fig. D5-2
P3504 P3502 Clampers <Rear View>
401
43
PT-43LC14 / PT-50LC14 / PT-60LC14
REMOVAL OF THE COVER SWITCH C.B.A. FROM THE CABINET

1. Remove the Projection Unit. Refer to Steps 1~2 in "REMOVAL OF THE PROJECTION UNIT FROM THE CABINET." 2. 1) Remove the Front Cover Unit from the 8 latches. 2) Remove the Optical Cover by removing the 2 Screws (454). 3) Remove the Screw (401) from the front side.
latches
Optical Cover
454
401
latches
454
Front Cover Unit

Fig. D6-1 4) To remove the Cover Switch C.B.A., remove the Display Support Plate L with the Cover Switch C.B.A. by removing the 2 Screws (401). 5) Remove the Cover Switch C.B.A. by removing the Screw (402).
Bosses
Cover Switch C.B.A.

402
Display Support Plate L

Fig. D6-2
401
Reassembly Note: When installing the Display Support Plate L with the Cover Switch C.B.A., install it with the Lamp Cover removed.
44
PT-43LC14 / PT-50LC14 / PT-60LC14
6 ADJUSTMENT PROCEDURES 1
WHEN REINSTALLING THE PROJECTION UNIT INTO THE UNIT AT THE USERS LOCATION:
The following ADJUSTMENT of the Projection Unit must be performed. a. Mechanical Picture Position Adjustment b. Focus Adjustment Note: Perform this adjustment only if necessary. (Normally, it will not be necessary.) c. Electrical Picture Position Adjustment Preparation of ADJUSTMENT: 1. Install all parts except the Front Cover Unit and the Optical Cover. 4. 1) Then, press and hold the VOLUME DOWN button on the unit and the SWAP key on the remote for more than 1 second. The unit will go into the Factory Adjust Mode. (FACTORY ADJUST menu will appear.)
F 4 D U N H R A 0 E N CTORY ADJUST 1/1 5252 S:04052002 O ADJ D
M: V S F O P
0 I O A T A
ER TIAL
DEFAULT SET (SELF CHECK)
<Factory Adjust mode>
Fig. M1-3 2) Then, press the CH UP/DOWN key on the remote to select "OTHER" on menu and press the OK key. (OTHER menu will appear.) Projection Unit
OTHER 1/1 RGB1
O O F G
P P I C
T H T V LTE :04
POSI POSI R DET 0525
0C 06 6B
(With Front Cover Unit and Optical Cover removed) <Front View> Fig. M1-1 Note: When the rear cover is disassembled, the screen can be moved back and forth, which could affect the video display vertical position. This could also cause the vertical adjust to be at or near its limit. Only try the picture position adjustment with the rear cover assembled! 2. Turn the power on. 3. Press and hold the VOLUME DOWN button on the unit and the RECALL key on the remote for more than 5 seconds in power on condition. The unit will go into Work Mode. ("WORK MODE" will appear on the screen.)
<Factory Adjust Mode> (OTHER menu 1/1)

Fig. M1-4 5. Press the VOLUME UP/DOWN key on the remote. (Focus screen will appear.)
O P T O P T
H P O S I V P O S I
0 C 0 6
RGB1
<Focus Screen>
To release this mode: 1. After completing the ADJUSTMENT, press the CH UP/ DOWN key on the remote to return to the OTHER menu. 2. Then, press RECALL key twice to return to Work Mode, and press and hold the VOLUME DOWN button on the unit and the RECALL key on the remote for more than 5 seconds. Alternatively, turn off the power. 3. Then, install the Optical Cover with the 2 Screws and the Front Cover Unit.
C-COR/GAM/W-BAL PUSH RECALL 5SEC WORK MODE
<Work Mode> Fig. M1-2
45
PT-43LC14 / PT-50LC14 / PT-60LC14
a. Mechanical Picture Position Adjustment (Tilt)

1) Loosen the 4 Screws on the Projection Unit.
b. Focus Adjustment
1) Confirm that each of the pixels in the nine portions is clearly visible.
Projection Lens Screw Screw Screw Screw

O P T O P T H P O S I V P O S I 0 C 0 6
Twist
Twist
<Focus Screen> 2) If not, loosen the Knob on the Projection Lens until the Knob can be moved.
<Front View>
Knob Tighten Loosen
Fig. M1-5 2) Adjust the Projection Lens by twisting so that the long line "g" and the long line "h" are within 4 dots. (The long line "g" and the long line "h" will be almost aligned horizontally.)
(PT-60LC14) CAUTION: Do not turn the screw and nut.
Up
O P T O P T O P T O P T H P O S I H P O S I V P O S I V P O S I 0 7 0 C 0 9 0 6
Down
"G" long line "g"
<Focus Screen> long line "h"
"H"
<Front View>
Fig. M1-6 3) Adjust the Knob by moving up or down so that each of the pixels in the nine portions is clearly visible to obtain the best focus. 4) Tighten the Knob. Note: Focus Adjustment is not normally necessary. Perform this adjustment only if necessary.
"G"
within 4 dots
"H"
Note: If the Projection Lens is twisted left, the Focus Screen twists left. If the Projection Lens is twisted right, the Focus Screen twists right. 3) Tighten the 4 Screws while fixing the Projection Lens.
46
PT-43LC14 / PT-50LC14 / PT-60LC14
c. Electrical Picture Position Adjustment

1) Adjust OPT HPOSI so that "C" is symmetrical to "D." by pressing the VOLUME UP/DOWN key on the remote to change the value. 2) Press the CH UP/DOWN key on the remote to return to the OTHER menu. 3) Select OPT VPOSI by pressing CH UP/DOWN key on the remote. 4) Adjust OPT VPOSI so that "A" is symmetrical to B by pressing the VOLUME UP/DOWN key on the remote to change the value.
"E" "I"
O P T O P T H P O S I V P O S I 0 C 0 6
"A"
"F" "J"
"C"
"D"
"K" "G" "B" <Focus Screen> "H"
"L"
"C"
"D" width "c" = width "d" width "c" "A" width "a" width "a" = width "b" width "b" "B" width "d"
5) Confirm that all "A", "B", "C", "D", "E", "F", "G", "H", "I", "J", "K", "L" are each almost symmetrical. 6) If not, adjust the "OPT HPOSI" and "OPT VPOSI" (repeat steps 1-6) until the picture is in the correct position. 7) Press the CH UP/DOWN key on the remote to return to the OTHER menu.
47
PT-43LC14 / PT-50LC14 / PT-60LC14
7 ADJUSTMENT PROCEDURES 2
INITIAL GUIDELINE
The table below shows which adjustments are necessary according to the unit parts and individual parts to be replaced. Make sure to perform these adjustments shown below as necessary.
Tuner C.B.A. is included in TV/Tuner Unit Tuner1 (Main Tuner) IC7501 (MTS/SAP Signal Process)
Replacement Parts Adjustment Item Tuner C.B.A. Separation Adjustment (VR Adjustment) Adjustment Section Note: : Adjustment Item Fig. E1-1
Section
Adjustment Item
Necessary Equipment
MTS/SAP Signal Generator Oscilloscope Plastic Tip Driver
Input
MTS Signal (Only L CH, 300Hz, 30% Modulating) RF (TV)
Tuner C.B.A. Separation Adjustment Adjustment (VR Adjustment) Section
Fig. E1-2
TEST EQUIPMENT
To do all of these electrical adjustments, the following equipment is required. 1. Dual-Trace Oscilloscope Voltage Range: 0.001 V to 50 V/Div. Frequency Range: DC to 50 MHz Probes: 10:1, 1:1 2. NTSC Video Pattern Generator 3. Plastic Tip Driver and Non-Metal Driver 4. MTS/SAP Signal Generator (TV Multi-Channel Sound Modulator (U.S.A.))
48
PT-43LC14 / PT-50LC14 / PT-60LC14
HOW TO READ THE ADJUSTMENT PROCEDURES

Connecting Point (Test Point) of Oscilloscope Adjustment component
Supply NTSC COLOR BAR SIGNAL to the Video Input Connector
SEPARATION ADJUSTMENT (VR ADJUSTMENT)

Purpose: To separate the L and R Channels of Stereo Signal. Symptom of Misadjustment: The L and R Channels of Stereo Signal will not be separated properly resultin in no stereophonic effect.
TP TP3602 TP3603
ADJ. R3662
INPUT
TP
(Video input Connector) NTSC Color Bar Signal
ADJ. R7514
INPUT (RF Input Terminal) MTS (ONLY L CH) 300 Hz5 Hz 30 % Modulating SPECIFICATION Refer to Description below
TP7501
EQUIPMENT Oscilloscope, NTSC Video Pattern Generator
SPECIFICATION A=0.2 V 0.06 V DC
EQUIPMENT
Equipment required for adjustment Specification for Adjustment
Oscilloscope MTS/SAP Signal Generator Plastic Tip Driver
Fig. E2-1 Note: TP7501, R7514: Tuner C.B.A.

CH1
CH2
CH1: TP3603 2V
1 2
CH2: TP3602 10 s 1
6 4 5 2 Volts/DIV (CH1) 4 Connecting Point 6 Trigger Channel of the Scope 1 : CH1 2 : CH2
1V
3
1. Connect the MTS/SAP Signal Generator to the RF Input Terminal. Then, set the MTS/SAP Signal Generator as follows. MTS (ONLY L CH) 300 Hz 5 Hz 30 % Modulating 2. Set to TV mode by pressing TV/VIDEO key on the remote and then set to STEREO audio mode by pressing SAP key on the remote. 3. Connect the Oscilloscope to TP7501 on the Tuner C.B.A. 4. Adjust R7514 (SEPARATION) on the Tuner C.B.A. so that the signal level is minimum.
1 Connecting Point 3 Volts/DIV (CH2) 5 Time/DIV
Minimum
Fig. E2-2
75 % White
100 % White
TP7501(R CH) 20 mV
Fig. E3
1 ms
75 % Color Bar Signal (Standard)

Fig. E2-3
49
PT-43LC14 / PT-50LC14 / PT-60LC14
TEST POINTS AND CONTROL LOCATION Tuner C.B.A.
SEPARATION R7514 TP7501
(Component Side)
Test Point Information Test Point with a Test Pin. Test Point with a jumper wire across a hole in the P.C.B. Test Point with no Test Pin. Test Point with a Hook.
50
PT-43LC14 / PT-50LC14 / PT-60LC14
8 TROUBLESHOOTING HINTS FOR BLOCK LEVEL REPAIR

MAIN PARTS LOCATION
<Front View>
Network C.B.A.
Lamp Cover Cover Switch C.B.A.
TEMP LED LAMP LED Network C.B.A.
Optical Cover Front Cover Unit Operation C.B.A. POWER LED
<Rear View>
Projection Unit Thermal Fuse Unit Thermistor 1 C.B.A. Air Filter Fan Case Unit (Fan 1) Thermistor 2 C.B.A. Fan 3
Front Jack C.B.A. Main C.B.A.
Ballast C.B.A. Tuner C.B.A.
Fan 2 LCD Drive C.B.A.
Audio Amp C.B.A.
Fan 4
Rear Cover Power C.B.A. Rear Jack C.B.A. TV/Tuner Unit
51
PT-43LC14 / PT-50LC14 / PT-60LC14
ERROR INDICATION INFORMATION

Each LED indication facilitates finding the cause of the error. When an error is detected, the Lamp comes off and the LED on the front will flash.
POWER LED
TV/VIDEO
TEMP LED
LAMP LED
(Note 2) (Note 3) LAMP OFF
Error No.
1) 2) 3) 4) 5) 6) 7) 8) 9) 10) 11) 12) 13) 14) 15) 16) 17)
Error Information
Fan1, Fan2 or Fan3 stopped Lamp Cover open Temperature Sensor shorted or open (Thermistor 1 C.B.A.) Abnormal Temperature (Thermistor 1 C.B.A.) Ballast Error (abnormal Lamp or Ballast)
POWER LED
flashes orange once every 5 seconds flashes orange twice every 5 seconds -
TEMP LED
flashes once every 5 seconds flashes twice every 5 seconds -
LAMP LED
-
OSD
flashes once every 5 seconds flashes twice every 5 seconds flashes 3 times every 5 seconds flashes 4 times every 5 seconds flashes once every 5 seconds flashes twice every 5 seconds flashes 3 times every 5 seconds flashes 4 times every 5 seconds flashes 5 times every 5 seconds flashes 6 times every 5 seconds -
Ballast Error (abnormal Lamp voltage) Ballast Error (abnormal temperature) Ballast Error (other causes) Abnormal Voltage on 30 V line Abnormal Voltage on 9 V line Abnormal Voltage on 5 V line Abnormal Voltage on 3.3 V line Abnormal Voltage on -5 V line Abnormal Voltage on 6 V line Temperature Sensor shorted or open (Thermistor 2 C.B.A.) Abnormal Temperature (Thermistor 2 C.B.A.) Clogged air filter
flashes orange 5 times every 5 seconds flashes orange 6 times every 5 seconds flashes orange 7 times every 5 seconds flashes orange 8 times every 5 seconds flashes orange 9 times every 5 seconds flashes orange 10 times every 5 seconds -
flashes once every 5 seconds flashes twice every 5 seconds flashes 3 times every 5 seconds flashes 4 times every 5 seconds flashes 5 times every 5 seconds flashes 6 times every 5 seconds flashes 3 times every 5 seconds flashes 4 times every 5 seconds flashes 5 times every 5 seconds
Note: 1. When two or more errors have occurred at the same time, the LED will alternate flash patterns as shown above every 5 seconds. 2. Warning OSD appears when the air filter is clogged. 3. LAMP OFF: The LED will flash immediately after the Lamp comes off. 4.The detected error data will be stored in the EEPROM.
52
PT-43LC14 / PT-50LC14 / PT-60LC14
How to solve the problem indicated by the Error Indication of LED

(All symptom is that Lamp turns off or Lamp does not light up) Note: Before performing the troubleshooting, confirm that all connector cables in the unit are connected to connectors correctly. Error No.
1)
Problem
Cooling Fan (Fan1, Fan2 and/or Fan3) malfunction. NO
Possible Solution
Replace the Power C.B.A.Still NG, replace the Projection Unit. Still NG, replace the Main C.B.A. Replace the Projection Unit. Replace the Projection Unit. Replace the Fan3.
Are the Fan1, Fan2 and Fan3 operating?
Only the Fan1 stops. Only the Fan2 stops. Only the Fan3 stops.
2)
Mis-installed the Lamp Cover (the Lamp cover is open).
1. Tighten the screw of the Lamp Cover. 2. If still NG, replace the Cover SW (SW2911) on the Cover Switch C.B.A. 3. If still NG, replace the Main C.B.A. 4. If still NG, replace the Projection Unit. Remove P2303 connector on the LCD Drive C.B.A. and check if the resistance between pin1 and pin2 of P2811 on the Thermistor 1 C.B.A. is 5k 200k . If NG, replace the Temperature Sensor (R2811) on the Thermistor 1 C.B.A. Still NG, replace the Projection Unit. Still NG, replace the Main C.B.A. Note: The Projection Unit includes LCD Drive C.B.A.
3)
The temperature sensor (R2811) on the Thermistor 1 C.B.A. on the Fan 1 is short or open.
4)
It indicates when the temperature detected by the Temperature Sensor (R2811) on Thermistor 1 C.B.A. exceeds 55 C (131 F). 1. The surrounding temperature of the place of use may be too high. 2. The vents on the rear may be blocked.
1. Relocate the unit to a proper location. Do not place in direct sunlight and other sources of direct heat. Do not place the unit in humid or dusty location, or areas exposed to smokeor steam. (surrounding temperature should be between 0 C (32 F) and 40 C (104 F) and humidity should be between 20 % and 80 % (with no condensation).) The vents are not blocked. It is recommended that a gap of at least 10 cm is left all around the unit even when it is placed inside a cabinet or between shelves. 2. Check if the fans are operating properly.
5)
1. Confirm that the Thermal Fuse Unit (115C(239F)) on the Lamp House is not open. The Lamp is not cooled off. Thermal Fuse Unit (115C (239F)) is defective (open). 2. Wait until the Lamp is cooled off and try to turn the power back on. If same error LED The Lamp is defective (crack). indication continues, remove the Lamp and visually inspect it. If it is cracked, it must be The Lamp voltage becomes more over 130V or less replaced. If the Lamp is not cracked, replace the Ballast C.B.A. than 30V. 3. If still NG, replace the Main C.B.A. 5. The Ballast C.B.A. is defective. 6. The Main C.B.A. is defective. 1. 2. 3. 4. The Lamp is defective (short of the Lamp). Thermal fuse (F1302) 117 C (243 F) on the Ballast C.B.A. is open due to abnormal temperature rise. The Ballast C.B.A. is defective. +30V line on the Main C.B.A. error. Replace the Lamp. Replace the Ballast C.B.A. If the Lamp does not light up after attempting turning on the power 2 or 3 times, replace the Ballast C.B.A. 1. Replace the Power C.B.A. 2. If still NG, replace the Main C.B.A. 3. If still NG, replace the Tuner C.B.A. 1. Replace the Power C.B.A. 2. If still NG, replace the Main C.B.A. 3. If still NG, replace the Rear Jack C.B.A. 4. If still NG, replace the Projection Unit. 1. Replace the Power C.B.A. 2. If still NG, replace the Main C.B.A. 3. If still NG, replace the Rear Jack C.B.A. 4. If still NG, replace the Tuner C.B.A. 5. If still NG, replace the Projection Unit. 1. Replace the Power C.B.A. 2. If still NG, replace the Main C.B.A. 1. Replace the Power C.B.A. 2. If still NG, replace the Main C.B.A. 1. Replace the Power C.B.A. 2. If still NG, replace the Main C.B.A. Remove P2304 connector on the LCD Drive C.B.A. and check if the resistance between pin1 and pin2 of P2821 on the Thermistor 2 C.B.A. is 5k 1M . If NG, replace the Temperature Sensor (R2821) on the Thermistor 2 C.B.A. Still NG, replace the Projection Unit. Still NG, replace the Main C.B.A. Note: The Projection Unit includes LCD Drive C.B.A.
6) 7) 8) 9)
10)
+9V line on the Main C.B.A. error.
11)
+5V line on the Main C.B.A. error.
12) 13) 14) 15)
+3.3V line on the Main C.B.A. error. -5V line on the Main C.B.A. error. +6V line on the Main C.B.A. error. The temperature sensor (R2821) on the Thermistor 2 C.B.A. on the Lamp House is short or open.
16)
It indicates when the temperature detected by the Temperature Sensor (R2821) on Thermistor 2 C.B.A. exceeds 85 C (185 F). 1. The surrounding temperature of the place of use may be too high. 2. The vents on the rear may be blocked.
1. Relocate the unit to a proper location. Do not place in direct sunlight and other sources of direct heat. Do not place the unit in humid or dusty location, or areas exposed to smokeor steam. (surrounding temperature should be between 0 C (32 F) and 40 C (104 F) and humidity should be between 20 % and 80 % (with no condensation).) The vents are not blocked. It is recommended that a gap of at least 10 cm is left all around the unit even when it is placed inside a cabinet or between shelves. 2. Check if the fans are operating properly. 1. Cleaning the Air Filter on the Projection Unit. 2. If still NG, replace the Projection Unit. 3. If still NG, replace the Main C.B.A.
17)
Clogged air filter of the Fan Case Unit.
53
PT-43LC14 / PT-50LC14 / PT-60LC14
No picture or abnormal picture
Check that there is no picture or abnormal picture on the screen from all input terminals.
ABNORMAL PICTURE: No Color Picture (Black and White picture) Abnormal Color Picture No Synchronisation Picture Dark Picture
(All input are NG.)
Does the OSD appear on the screen? YES Replace the Main C.B.A.
NO
Replace the Projection Unit. Still NG, replace the Main C.B.A.
(Only Video1 OR 2 input is NG.) Replace the Rear Jack C.B.A.
(Only Video3 input is NG.)
Replace the Front Jack C.B.A. Still NG, replace Rear Jack C.B.A.
(Only tuner input is NG.)
Replace the Tuner C.B.A. Still NG, replace the Rear Jack C.B.A.
(Only RGB 1 input is NG.)
Replace the Main C.B.A.
Replace the Front Jack C.B.A. Still NG,replace the Main C.B.A.
(Only Component 1, 2, 3 OR 4 input is NG.)
In the case that one or some input is NG, it can be judged that the Projection Unit is OK.
Replace the Rear Jack C.B.A.
(Component 1, 2, 3 AND 4 input is NG.)
Replace the Main C.B.A. Still NG, replace the Rear Jack C.B.A.
(Only HDMI input is NG.)
(Tuner, Component AND Video input is NG.)
Replace the Rear Jack C.B.A.
(PC/SD Card input is NG.)
54
PT-43LC14 / PT-50LC14 / PT-60LC14
No sound from built-in both L-CH and R-CH Speakers

Check that there is an audio signal to the Audio Out Terminal from all input terminals. (All input are NG.) (Only Audio1, 2, Component 1, 2, 3, OR 4 input is NG.) Replace the Rear Jack C.B.A. Replace the Rear Jack C.B.A.
(Only Audio3 input is NG.)
Replace the Front Jack C.B.A. Still NG, replace the Rear Jack C.B.A.
(Only Tuner input is NG.)
Replace the Tuner C.B.A. Still NG, replace the Rear Jack C.B.A.
Replace the Front Jack C.B.A. Still NG, replace the Main C.B.A.
(Only HDMI input is NG.) OK
Replace the Audio Amp C.B.A. Still NG, Replace the Rear Jack C.B.A. Still NG, Replace the Power C.B.A.
No sound from built-in L-CH Speaker only

Press "MENU" button on the remote and select "BALANCE" in MENU screen. Then press "OK." NO
Does the "BALANCE" becomes center position? YES Replace the L-CH Speaker.
Set to the center position.
No sound from built-in R-CH Speaker only

Press "MENU" button on the remote and select "BALANCE" in MENU screen. Then press "OK." NO
Does the "BALANCE" becomes center position? YES Replace the R-CH Speaker.
Set to the center position.
55
PT-43LC14 / PT-50LC14 / PT-60LC14
56
PT-43LC14 / PT-50LC14 / PT-60LC14
9 BLOCK DIAGRAMS
OVERALL BLOCK DIAGRAM
REAR JACK C.B.A.
IC3502
COMPONENT AUDIO IN 1 (L/R) COMPONENT AUDIO IN 2 (L/R) COMPONENT AUDIO IN 3 (L/R) COMPONENT AUDIO IN 4 (L/R) AUDIO IN 1 (L/R) AUDIO IN 2(L/R) COMPONENT AUDIO IN1(L/R) COMPONENT AUDIO IN2(L/R) COMPONENT AUDIO IN3(L/R) COMPONENT AUDIO IN4(L/R) AUDIO IN 1(L/R) AUDIO IN 2(L/R) TUNER AUDIO(L/R) AUDIO IN 3(L/R) RGB2 AUDIO IN(L/R) RGB1/HDMI/DVI AUDIO IN(L/R)
AUDIO AMP C.B.A.

IC3501
P3603 P4505
NETWORK C.B.A. (FOR R-CH)

IC4501
P4552 P4503 P4553 P4551 SPEAKER-R (TWEETER) SPEAKER-R (WOOFER)
SOUND PROCESSOR
AUDIO AMP
NETWORK C.B.A. (FOR L-CH)

P4552
AUDIO SW
P4553
SPEAKER-L (WOOFER) P4551 SPEAKER-L (TWEETER)
MAIN C.B.A.
IC5004 IC5301 IC5304
FIFO I/F SDRAM I/F DATA BUS (32bit)
MAIN VIDEO SIGNAL PROCESS
64M SDRAM
<FOR SCALER(720p CONVERTER)>
LCD DRIVE C.B.A.

IC2503 IC2505
IC5302,5303
IC5702
IC5705
FPGA
AUDIO OUT (L/R) VIDEO OUT AUDIO OUT(L/R) VIDEO OUT
P5302 R DATA (8bit) TTL PARALLEL TO LVDS SERIAL CONVERTER
P2501
LVDS RECEIVER
LVDS SERIAL TO TTL PARALLEL CONVERTER
SIGNAL PROCESS FOR LCD PANEL

R DATA (8bit)
IC2001 P2001
R DATA (10bit)
A/D
IC3504
3D Y/C SEPARATION NTSC DECODER
YUV DATA (10bit)
SW GC3FM
I/P CONVERTER R DATA (8bit) PICTURE CONTROL MULTI WINDOW G DATA (8bit) PICTURE IN PICTURE SPLIT SCREEN SEARCH B DATA (8bit) SCALER(720p CONVERTER)
OSD MIX D/D CONVERTER
G DATA (8bit) B DATA (8bit)
LVDS DATA/CLOCK
COLOR CORRECTION
SAMPLING HOLD
D/A
R DATA (12bit)
LCD(R)
LEVEL SHIFTER
COMPONENT IN 1(Y/PB/PR) COMPONENT IN 2(Y/PB/PR) COMPONENT IN 3(Y/PB/PR) COMPONENT IN 4(Y/PB/PR) VIDEO IN 1 VIDEO IN 2 S-VIDEO IN 1 S-VIDEO IN 2
COMPONENT1 Y/PB/PR P3601 COMPONENT2 Y/PB/PR COMPONENT3 Y/PB/PR COMPONENT4 Y/PB/PR DATA BUS (32bit) OSD DATA (0-3) MAIN Y/V, PB/C, PR P3403
LVDS TRANSMITTER
IC2002 P2002
G DATA (8bit)
COLOR CORRECTION
G DATA (10bit)
SAMPLING HOLD
D/A
G DATA (12bit)
VIDEO IN 1 VIDEO IN 2 S-VIDEO IN 1 S-VIDEO IN 2 TUNER VIDEO 1
VIDEO SW
IC5104
SUB Y/V, PB/C, PR
IC5103
IC5707
LCD(G)
LEVEL SHIFTER IC5306
SUB VIDEO SIGNAL PROCESS
64M SDRAM
Y DATA (8bit) UV DATA (8bit) DATA BUS (32bit)
SW
A/D
2D Y/C SEPARATION NTSC DECODER
64M SDRAM
<FOR IP CONVERTER, MULTI WINDOW, 3D Y/C SEPARATION, ETC>
IC2003 P2003
B DATA (8bit)
GC3FS
TUNER VIDEO 2 VIDEO IN 3 S-VIDEO IN 3
GC3I VIDEO SIGNAL PROCESS
COLOR CORRECTION
B DATA (10bit)
SAMPLING HOLD
D/A
B DATA (12bit)
LCD(B)
NON-UNIFORMITY COLOR COMPENSATION GAMMA CORRECTION WHITE BALANCE CONTROL LEVEL SHIFTER
TUNER C.B.A.
U7001 (MAIN TUNER) RF-IN RF-OUT AUDIO VIDEO
IC7501
P7002 TUNER AUDIO (L/R)
P3501
MTS/SAP AUDIO SIGNAL PROCESS
TIMING GENERATOR
IC9001
128M SDRAM
DATA BUS (16bit) P7003 P9002
CARD YUV DATA (8bit)
FAN1 SPEED CONTROL
IC2902
P2902
(FAN 1)
U7101 (SUB TUNER) RF-IN VIDEO
IC2301
DRIVE EEPROM
IC2903
IC9004
DATA BUS (4bit)
ADJUSTMENT DATA/SETTING DATA OF EACH IC's FOR LCD DRIVE C.B.A. IC6005 IC2304
P2903
SD CARD
FRONT JACK C.B.A.
P3902 VIDEO IN 3 S-VIDEO IN 3 AUDIO IN 3 (L/R) P3903 RGB AUDIO IN2(L/R) P3504 P3502 P9201
(FAN 2)
DRIVE
FAN2 SPEED CONTROL
IC9207,IC9208
PC CARD
TRANSCEIVER
DATA BUS (16bit)
SD/PC CARD SIGNAL PROCESS
EEPROM
LAMP TIME DATA ADJUSTMENT DATA SERIAL DATA/CLOCK
LCD MICROCONTROLLER
DATA BUS (8bit)
IC6006
IC9007
EEPROM
SETTING DATA OF EACH IC's FOR MAIN C.B.A. USER ADJUSTMENT DATA
FAN3 SPEED CONTROL FAN1 ON(H) FAN2 ON(H) FAN3 ON(H)
IC2904
P2904
(FAN 3)
DRIVE
FLASH MEMORY
PROGRAM FOR CARD PROCESSOR (IC9004)
IC4002
HDMI AUDIO IN2(L/R) RGB AUDIO IN1(L/R) DVI AUDIO IN(L/R) P3404 P3602
IC6003
I2C SERIAL DATA/CLOCK FILTER ERROR DETECTION LAMP COVER OPEN(H)
COVER SWITCH C.B.A.

P2502
LAMP COVER OPEN(H)
I2C SERIAL DATA/CLOCK
P3601
P3403
P2912 COVER SW
SW
P6004 SERIAL DATA/CLOCK
IC2905
P3901 RGB IN2
P5501
MAIN MICROCONTROLLER
I2C SERIAL DATA/CLOCK
OP AMP
LAMP ON(H) LAMP STATUS(ERROR) THERMO TEMP DATA 3
THERMISTOR 1 C.B.A.
P2303 P2811 TEMPERATURE SENSOR
IC5501
RGB2 R RGB1 R RGB2 G RGB1 G RGB2 B RGB1 B
SW SW SW
R G B
Q5510-Q5514
RGB-->YUV CONVERTER
SERIAL DATA/CLOCK SERIAL DATA/CLOCK
IC6302
THERMO TEMP DATA 3 THERMO TEMP DATA 1 FAN(1,2,3) LOCK (H) FAN1 SPEED CONTROL
THERMISTOR 2 C.B.A.
P2304
THERMO TEMP DATA 1
RGB AUDIO IN1(L/R)
P2821
(PT-50LC14/PT-60LC14) IC5802
RGB IN1 I2C SERIAL DATA/CLOCK
TEMPERATURE SENSOR
EEPROM
HDMI INFORMATION DATA I2C SERIAL DATA/CLOCK TMDS DATA/CLOCK
IC5803
HDMI Y DATA (8bit)
+3.3V TEMP LAMP POWER DRIVE
DVI AUDIO IN(L/R)
SUB MICROCONTROLLER
BALLAST C.B.A.
P1302
POWER C.B.A.
P805 IC1006 P1006
HDMI IN
HDMI INTERFACE
HDMI UV DATA (8bit) I2C SERIAL DATA/CLOCK
P6701
P6305
IC5805
D/A
HDMI AUDIO IN2(L/R)
OPERATION BUTTON (KEY MATRIX)
REMOTE SENSOR
P6002
P1305
(FAN 4)
BALLAST CIRCUIT
LAMP
AC IN
POWER SUPPLY CIRCUIT
DRIVE
OVERALL BLOCK DIAGRAM PT-43LC14/PT-50LC14/PT-60LC14

57
PT-43LC14 / PT-50LC14 / PT-60LC14
POWER SUPPLY BLOCK DIAGRAM

POWER C.B.A.
TP1021 P804-1 P804-2 F801 6.3A 125V/250V L802 AC LINE FILTER L803 AC LINE FILTER F1001 5A 125V/250V L1001 AC LINE FILTER D1002-1005 FULL-WAVE RETIFIER T1001 PR1010
1 10
AUDIO AMP C.B.A.

TP1004 P1009 TP1005
11
TUNER C.B.A.
P6004-6 P6004-5 P7003-6 P7003-5 +30V +5V
AC IN
P4501-1 P4501-2 P4501-3
+16V
IC1001 (SWITCHING CONTROL)

4
P1010 TP1003 PR1011 P1011 TP1007 TP1008 (+30V) (+12V) (+3.3V) (+6V) (-5V) (+9V) (+17V)
VCC OVER VOLTAGE PROTECTION DRIVE CONTROL D S

1 3 12
REAR JACK C.B.A.

-16V P3404-1, 2 P3404-4, 5 P3602-1, 2 P3602-4, 5 +9V +5V
RL801
5
TP1015 Q801 POWER ON(H) <FROM IC6302 (72)>
TP1020
2 4
MAIN C.B.A.
P1007-1 P1007-3 P1007-6,7 P1007-5 P1007-8 P1007-4 P1007-2 P3401-1 P3401-3 P3401-6,7 P3401-5 P3401-8 P3401-4 P3401-2 +30V +3.3V +6V -5V +9V +5V
4
13
TP1022 PR1012
6 14
TP1009 TP1010 TP1006
TP1023 (18.5V) TP1024 TP1025 (17V) RL802
Q1001-1003 +19V REGULATOR
PR1001
7 15
PR1013 PR1014
8 16
IC3402
2
PR1003
+9V REG.
IC3401
2
Q1004-1006 +17V REGULATOR
17
TP1012
+5V REG.
IC6303
5
R809 (RUSH CURRENT PROTECTOR)
IC1002 FEED BACK
IC1005 (SHUNT REGULATOR)

3 1
P3402-1 P3402-2 P3402-3 P3402-4
IC6302
4 11
+3.3V REG.
IC6003
32 77
Q6303 REG.
56
SUB MICROCONTROLLER
MAIN MICROCONTROLLER
V-REF(2.495V) IC1006 (FAN4 DRIVE) (8V) PR1008

3
LCD DRIVE C.B.A.

DC/DC CONVERTER (STEP-DOWN CHOPPER SYSTEM) IC1003 IC2901 (+15.5V REGULATOR) (+6V) P2901-1 P2901-2 P2901-3 P2901-4 (+17V) (+12V) (+5V) (+3.3V)
2
TP1013
REG.
4
(+12V)
18 19 20 21
SWITCHING
11 12 13 14 3 2 32
+15.5V REG.
1 5
TP2906
4
TP2901 SW +15.5V SW +15.5V CONTROL <FROM IC2304 (26)> LCD ON (H) <FROM IC2304 (51)>
STANDBY POWER CIRCUIT

T801
6 4 3 2 1
VCC
OVER CURR. LIMITER CONSTANT VOLTAGE CONTROL
IC2902 (FAN1 DRIVE)

2
+5V TP2907
4
TP2911 (7.75V) P2902-1 P2902-2 P2902-3
FAN 1
TP804
D803-806 FULL-WAVE RETIFIER
TP803
TP810
REG.
1 5
(STBY+9V)
IC2905 (OP AMP)

7 5 6
FAN1 SPEED CONTROL <FROM IC2503(7)>
FAN1 OH (H) <FROM IC2304 (53)> FAN4 P1006-1 P1006-2 IC2903 (FAN2 DRIVE)
2
TP2908
4
TP2912 (8.75V) P2903-1 P2903-2 P2903-3
FAN2
REG.
1 5
BALLAST C.B.A.
THERMAL FUSE UNIT F001 115 C (239 F) P1306-1 P1306-2 P805-1 P805-2 P1302 P1303 F1301 5A/250V L1301 AC LINE FILTER TP1301 VOLTAGE MULTIPLYING RECTIFIER C1305 C1306 D1302 TP1302 Q1307 Q1309 L1303, C1309-1311 NOISE REDUCTION DC/DC CONVERTER (STEP-DOWN CHOPPER SYSTEM) TP1305 Q1304 R1321 WATTAGE Q1306 Q1308 IC2904 (FAN3 DRIVE)
2
FAN2 SPEED CONTROL <FROM IC2304 (28)> FAN2 OH (H) <FROM IC2304 (55)> DC/AC INVERTER TP2909
4
TP2913 (7.75V) P2904-1 P2904-2 P2904-3
FAN3
REG.
1 5
FAN3 SPEED CONTROL <FROM IC2304 (30)> FAN3 ON (H) <FROM IC2304 (73)>
+17V +11V F1302 THERMAL FUSE 117 C (243 F) Q1305 P1001-4 P1001-5 P1001-1 P1001-2 P1301-4 P1301-5 P1301-1 P1301-2 (17V) Q1301 (18.5V) TP1306 TP1303 +5V +3.3V FAN(1,2,3) LOCK (H) <TO IC6302 (6)>
Q1302
VCC(+19V) VCC(+17V) THERMISTOR PWM CONTROL LAMP GND ERROR CURRENT DET ERROR VOLTAGE DET
T1301
MAIN C.B.A.
IC1303 OPTICAL ISOLATOR IC1304 OPTICAL ISOLATOR FROM SYSTEM CONTROL BLOCK DIAGRAM STANDBY(L)/POWER ON(H) LAMP ON(H) LAMP STATUS(ERROR) P6002-1 P6002-2 P6002-3 P1305-1 P1305-2 P1305-3 IC1302 OPTICAL ISOLATOR TP1304
LAMP
INVERTER DRIVE3 INVERTER DRIVE1 INVERTER DRIVE2 INVERTER DRIVE4 HV ON(H) D1315
LAMP ON(L)
LAMP STATUS LAMP ON LAMP OFF ERROR 1 ERROR 2 ERROR 3 ERROR 4
SIGNAL H L PULSE (T=128 msec) PULSE (T=96 msec) PULSE (T=64 msec) PULSE (T=32 msec) "2T" (ERROR PULSE)
LAMP ERROR PULSE
BALLAST CONTROL CIRCUIT U1301(HIC)
Q1310
Q1310 TURNS ON WHEN LAMP STARTS UP.
POWER SUPPLY BLOCK DIAGRAM PT-43LC14/PT-50LC14/PT-60LC14

58
PT-43LC14 / PT-50LC14 / PT-60LC14
VIDEO SIGNAL PATH I BLOCK DIAGRAM (1/2)

REAR JACK C.B.A.
IC3504 (VIDEO SW) JK3601 COMPONENT -Y1 COMPONENT -PB1 COMPONENT -PR1 JK3602 COMPONENT -Y2 COMPONENT -PB2 COMPONENT -PR2 JK3603 COMPONENT -Y3 COMPONENT -PB3 COMPONENT -PR3 JK3604 COMPONENT -Y4 COMPONENT -PB4 COMPONENT -PR4
39 33 27 21
MAIN C.B.A.
IC5004 (MAIN VIDEO SIGNAL PROCESS)
1,12,23,32,73,90, 105,113,114
+3.3V IC5002
5
VCC
GC3FM
3-5,136-143
23
25
TP3603
+2.5V REG.
66,71,79,84 4
VCC
115-122,125-132
IC5003
5
+2.5V REG.
38,40,45,47,52,54,58 4
VCC
V-SYNC 109 H-SYNC 110 CLOCK 111 FR CLOCK1 24
TP3602
29
IC5001
8
31
+2.5V REG.
VCC
10,21,30,75,88,114, 123,135
TP3601 MAIN Y/V

35
60
Q3503 Q3504 Q3505
B B B
P3601-6 P3601-8 P3601-9
P3403-6 P3403-8 P3403-9
Q5002 Q5003 Q5004
B B B
LPF LPF LPF
Q5005 Q5006 Q5007
B B B
Q5008 Q5010 Q5009
B B B
56 42
Y/V PB/C
A/D A/D A/D 3D Y/C SEPARATION NTSC DECODER YUV DATA

8,9,13-20
MAIN PB/C 59
37
YUV DATA (10BIT)
MAIN PR
58
PR 49
41
H-SYNC H-SYNC V-SYNC CLOCK

6 104 7 2
43
IC5104 (SW) SUB Y/V SUB PB/C

56 55 54
IC5103 (SUB VIDEO SIGNAL PROCESS) Q5111 Q5113 Q5112 +9V Y/V PB/C PR
Q3506 Q3507 Q3508
B B B TP3604
P3601-11 P3601-13 P3601-14
P3403-11 P3403-13 P3403-14 JK5501
Q5103 Q5106 Q5107
B B B
LPF LPF LPF
Q5105 Q5109 Q5110
B B B
Q5108
S-VIDEO IN1
JK3501 Y C
17 77 3 9 15
SUB PR
(PT-50LC14/PT-60LC14)
1 16 9 8 14 11
H L H L H L
3 6 5
B B B
40 30 35
A/D A/D A/D V-SYNC 72 H-SYNC 73 CLOCK 94 FR CLOCK1 68 FR CLOCK2 70 2D Y/C SEPARATION NTSC DECODER
74-76,78-80,83,84 85,86,88-93
Y DATA (8BIT) UV DATA (8BIT)
VCC 13
12 7 2
VIDEO IN1 Y C
VIDEO INPUT SELECT TP3605 RGB-IN 1
S-VIDEO IN2
R G B H-SYNC V-SYNC
RGB(L) <FROM IC6003 (11)> VCC +3.3V VCC IC5101
8,15,53,66,82,95 6,12,17,51,62,69, 81,97
VIDEO IN2
TP3606 +2.5V REG.

49,57 4
79 5 11
FRONT JACK C.B.A.

JK3901 R G B H-SYNC V-SYNC P3901-1 P3901-3 P3901-5 P3901-7 P3901-9 P5501-1 P5501-3 P5501-5 P5501-7 P5501-9 IC5501 (SW)
1 7
VCC
IC5102 Q5503
21
H L H L H L
B Q5504
Q5512 RGB --> Y CONVERT
Q5516 B
+2.5V REG.
28,33,38,41 4
VCC
RGB-IN 2
1 7 13
S-VIDEO IN3 VIDEO IN3
JK4801 Y C
3 9
19
B Q5505
Q5510,Q5511 Q5515 RGB --> PB B CONVERT Q5513,Q5514 Q5517 RGB --> PR B CONVERT Q5509, Q5518-Q5520 IC5505 (OR GATE)
1 2 4
GC3FS
IC5502 (INVERTER)
6 2
19 20
P3902-3 P3902-5 P3902-7
P3502-3 P3502-5 P3502-7
5 11
15
IC5105 (SW)
3 2
H L
24 23
H L
22
DELAY
VCC
5
VCC
8
TUNER C.B.A.
U7001 (MAIN TUNER) TP7001 RF-IN VIDEO 17 RF-OUT P7002-1 P3501-1
51 12 13
+3.3V H L VCC
14 16
+3.3V
6 5
H L
RGB1(H)RGB2(L) <FROM IC6003(22)>

1
VCC 16
+3.3V
+5V
20
RGB(L) <FROM IC6003 (11)> IC5803 (HDMI INTERFACE)
U7101 (SUB TUNER) TP7101 RF-IN VIDEO 17 P7002-3 P3501-3

8,47,53,57
JK5801 TMDS DATA0(+) TMDS DATA0(-) TMDS DATA1(+) TMDS DATA1(-) TMDS DATA2(+) TMDS DATA2(-) TMDS CLOCK(+) TMDS CLOCK(-) I2C SERIAL CLOCK I2C SERIAL DATA IC5802 (EEPROM) Q5803 I2C SERIAL CLOCK 6 I2C SERIAL DATA 5
DRIVE 77 76 87 86 92 91 97 96 84 83
XOR MASK TMDS DECODER
MODE CONTROL
YUV CONVERTER COLOR RANGE SCALING COLOR SPACE CONVERSION UP/DOWN CONVERSION
Y
49-55,58
WF65
HDMI Y DATA (8BIT)
UV
36-39,42-44,48
WF66
HDMI UV DATA (8BIT)

WF68 WF69
HDMI-IN +9V VCC
WF67
V-SYNC 34 H-SYNC 33 HDMI CLOCK(76MHz) 46 IC5805 (D/A CONVERTER)

32 30 31 27 2 3 4
IC5804 (OP AMP) D/A D/A

10 11 3 5 1 7
H-SYNC V-SYNC
FRONT JACK C.B.A.
I2C SERIAL CLOCK I2C SERIAL DATA
Q5802
DRIVE
AUDIO DATA DECODER
AUDIO DATA INTERFACE
HDMI AUDIO (R) HDMI AUDIO (L) -5V +5V
TO AUDIO BLOCK DIAGRAM
4.4 dB VEE 4 MAIN CLOCK GENERATOR JK3502 VIDEO OUT VCC 8 +5V VCC
1,6,11,14,17,,21,40, 47,56,64,67,82,89, 93,95,100 23,80 26 1
VCC 8 VCC 14 +5V
VCC
IC5801 +3.3V +5V

5
+3.3V 4 REG.
VIDEO SIGNAL PATH I BLOCK DIAGRAM (1/2) PT-43LC14/PT-50LC14/PT-60LC14

59
PT-43LC14 / PT-50LC14 / PT-60LC14
VIDEO SIGNAL PATH I BLOCK DIAGRAM (2/2)

MAIN VIDEO SIGNAL
IC5301 (VIDEO SIGNAL PROCESS)
SUB VIDEO SIGNAL
VIDEO SIGNAL(MAIN/SUB)
CARD Y/PB/PR SIGNAL
IC5304 (64M MEMORY) <FOR SCALER(720p COVERTER)>

E1,E2,E4, F1-F5,G2-G4 G1,H1-H3,J1-J5, K1-K5,L1,L5 L2 L3 L4
FIFO INTERFACE
SDRAM INTERFACE
Y22-Y25,AA23-AA26,AB18,AB19,AC22, AD17,AD18,AD21-AD24,AE17,AE18, AE21-AE26,AF17,AF18,AF21-AF25
DATA BUS(32BIT)
64M MEMORY
V-SYNC H-SYNC CLOCK
1,3,9,15,29,35,41, 43,49,55,75,81
VCC
+3.3V
IC5303 (BUS SW)

10,13 9,12
VCC 14
8,11
+5V OSD DATA 3 FROM OSD DATA 2 SYSTEM CONTROL OSD DATA 1 BLOCK DIAGRAM OSD DATA 0 OSD BLANKING MAIN SIGNAL PATH IC5702 (FPGA)
B1-B3,C1-C4,D2-D4 D1 E5 E3 98 97 96 95 94
IC5302 (BUS SW)

55
VCC 17 BUS SW
29-37,39,40
+5V
YUV DATA (10BIT)
16,18,20-28
IC5705 (LVDS TRANSMITTER)
CARD(L) <FROM IC6003 (79)> CARD YUV DATA(8BIT) FROM CARD CARD V-SYNC SIGNAL PROCESS CARD H-SYNC BLOCK DIAGRAM 27MHz CLOCK Y DATA (8BIT) UV DATA (8BIT)
56
V-SYNC H-SYNC CLOCK
FOR MAIN SIGNAL IP CONVERTER PICTURE CONTROL MULTI WINDOW PICTURE IN PICTURE SPLIT SCREEN SEARCH SCALER(720p CONVERTER) R DATA (8BIT) G DATA (8BIT) B DATA (8BIT)
A25,B24-B26, C24-C26,D24 V3,W1-W3, Y2,Y3,Y5 V24-V26,W26, Y1,AA1-AA3 147-154 157-164 166-173 110-112,115-119
R DATA (8BIT) G DATA (8BIT) B DATA (8BIT) V-SYNC H-SYNC
2-4,6,7,54-56 8,10-12,14-16,18 19,20,22-25,27,28 51 52
3-7,9-14
BUS SW
42-48,50-53
D/D CONVERTER (76MHz ---> 76MHz)
OSD MIX
122-124,127-131 134,135,138-143
SUB SIGNAL PATH

A6,A7,B6,B7, C5,C6,D5,E6 A8,A9,B8,C7, C8,C9,D7,D8 A5 B5 B9 A2
TTL PARALLEL TO LVDS SERIAL CONVERTER
H-SYNC W24 V-SYNC W25 CLOCK Y26
175 176
H-SYNC
V-SYNC 102 V-SYNC 101
V-SYNC CLOCK(76MHz) 178 CLOCK(76MHz) 81

1,10,24,36,46,54,68, 76,78,93,100,105,114, 126,137,145,180,201 17,42,61,86,108, 156,174,207 31
47 48 45 46 41 42 37 38 39 40
P5302-14 P5302-15 P5302-11 P5302-12 P5302-8 P5302-9 P5302-2 P5302-3 P5302-5 P5302-6
LVDS DATA A(+) LVDS DATA A(-) LVDS DATA B(+) LVDS DATA B(-) TO VIDEO II LVDS DATA C(+) SIGNAL PATH LVDS DATA C(-) BLOCK DIAGRAM LVDS DATA D(+) LVDS DATA D(-) LVDS CLOCK(+) LVDS CLOCK(-)
V-SYNC H-SYNC FOR SUB SIGNAL CLOCK HDMI CLOCK FR CLOCK2
PLL
9,26,34,44
CLOCK(76MHz) 92 VCC
B4
VCCE
VCCI
3-8,11-15,18-22,25-30,32-35,37,39-41,43,44
X5702 76M OSC
IC5706
4
+3.3V REG.
+5V
IC5708 +3.3V
8
+1.8V REG.
IC5707 (64M SDRAM)
DATA BUS(32BIT)
64M MEMORY
1,3,9,15,29,35,41, 43,49,55,75,81
VCC
+3.3V
IC5306 (64M SDRAM) <FOR IP COVERTER, MULTI WINDOW, 3D Y/C SEPARATION, ETC>
8AB1-AB5,AB8,AC2-AC4,AC8,AD5-AD8,AD11, AD12,AE4-AE8,AE11,AE12,AF4-AF8,AF10-AF12
DATA BUS(32BIT)
28,33,38,41
64M MEMORY
AVS(GND)
1,3,9,15,29,35,41, 43,49,55,75,81 P1,P2,ETC
VCC
+3.3V
VSS(GND)
L5307
P3,P4,ETC
AVD
+3.3V IC5305
1
L5304
D23,F23,ETC
VDDE
+1.8V REG.
U5,V5,ETC 3
VDDI
GC3I
VIDEO SIGNAL PATH I BLOCK DIAGRAM (2/2) PT-43LC14/PT-50LC14/PT-60LC14

60
PT-43LC14 / PT-50LC14 / PT-60LC14
VIDEO SIGNAL PATH II BLOCK DIAGRAM (Models: PT-43LC14 / PT-50LC14)

LCD DRIVE C.B.A.
IC2503 (LVDS RECEIVER) IC2505 (SIGNAL PROCESS FOR LCD PANEL)
+15.5V P2001-1 P2001-2 P2001-3 P2001-4 P2001-5 P2001-6 P2001-(7-18) P2001-19 P2001-20 P2001-21 P2001-22 P2001-23 P2001-24 P2001-25 P2001-26 P2001-27 P2001-28 P2001-29 P2001-30 P2001-31 P2001-32 P2001-33 P2001-34 P2001-35 P2001-36
LCD(R)
IC2001 (SAMPLING HOLD) LVDS DATA A(+) LVDS DATA A(-) LVDS DATA B(+) LVDS DATA B(-) LVDS DATA C(+) LVDS DATA C(-) LVDS DATA D(+) LVDS DATA D(-) LVDS CLOCK(+) LVDS CLOCK(-) P2501-14 P2501-15 P2501-11 P2501-12 P2501-8 P2501-9 P2501-2 P2501-3 P2501-5 P2501-6
10 9 12 11 16 15 20 19 18 17 30,32-35, 37-39
TP2001 (IC2001 PIN52 LINE) INVERTER AMP ON/OFF SW

52,54,56,58,60,62, 64,66,68,70,72,74
TP2004
R DATA (8BIT)
A5-A7,B6-B8, C7,C8

41-43,45-47, 49,50
NON UNIFORMITY COLOR COMPENSATION G DATA (8BIT)

A10-A12,B10-B12, C10,C11
W4-W6,Y1-Y7 S/H CLOCK(R) V2 XFR(R) V1 STSQO(R) W3 FRP U1
R DATA (10BIT)
GAMMA CORRECTION WHITE BALANCE CONTROL TIMING GENERATOR FOR PANEL DRIVE DY M19 DX ENABLE 4 ENABLE 3 ENABLE 2 ENABLE 1 NRG
Y10 V9 W9 Y9 W10 M1
86-95 96 97 98 99 100 24 23 33 37 36 35 34 27 22 38 25 3 5 4
D/A CONVERTER CONTROL LOGIC & DAC LATCH
VCC(A) 15,26,53,57,61,65,69,73,82 VCC(D) 1,50

19 18 39 43 42 41 40 28 44 45 20 21 81 80 79 77 78 13
+15.5V +3.3V
PLL
1-3,5,51, 53-55
B DATA (8BIT)
A15,A16,B14-B16, C14-C16
LEVEL SHIFTER (3.3V --> 15.5V)
CLX W8 CLY M18 H-SYNC 29 V-SYNC 27

26 E2 D2 E1
H-SYNC V-SYNC CLOCK(76 MHz) V-REF-H(+7V) V-REF-L(+5V)
SERIAL INTERFACE SCALE CONTROL D/A CONVERTER
12 11 10
SCALE CONTROL V1 V2 AMP SW
V-REF-H(+7.5V) V-REF-L(+7V) LCDCOM P2002-1 P2002-2 P2002-3 P2002-4 P2002-5 P2002-6 P2002-36 P2002-(7-18) P2002-19 P2002-20 P2002-21 P2002-22 P2002-23 P2002-24 P2002-25 P2002-26 P2002-27 P2002-28 P2002-29 P2002-30 P2002-31 P2002-32 P2002-33 P2002-34 P2002-35 P2002-36
LCD(G)
IC2002 (SAMPLING HOLD)

W15-W19,Y16-Y20 S/H CLOCK(G) W13 XFR(G) V13 STSQO(G) Y15 XFRP Y13

52,54,56,58,60,62, 64,66,68,70,72,74
TP2005
G DATA (10BIT)
IC2502 +5V
5
+3.3V 4 REG.
13,23,31,40,48,56
86-95 96 97 98 99 100 24 23 33 37 36 35 34 27 22 38 25 3 5 4
VCC(A) 15,26,53,57,61,65,69,73,82 VCC(D) 1,50

19 18 39 43 42 41 40 28 17 44 45 20 21 81 80 79 77 78 13
+15.5V +3.3V
VCC
V-REF-H(+7V) V-REF-L(+5V)
12 11 10
V-REF-H(+7.5V) V-REF-L(+7V) LCDCOM P2003-1 P2003-2 P2003-3 P2003-4 P2003-5 P2003-6 P2003-(7-18) P2003-19 P2003-20 P2003-21 P2003-22 P2003-23 P2003-24 P2003-25 P2003-26 P2003-27 P2003-28 P2003-29 P2003-30 P2003-31 P2003-32 P2003-33 P2003-34 P2003-35 P2003-36
LCD(B)

D20,E19,E20,F19,F20, G19,G20,H19,H20,J18

52,54,56,58,60,62, 64,66,68,70,72,74
TP2006
B DATA (10BIT)
S/H CLOCK(B) K20 XFR(B) K18 STSQO(B) J19 <FROM IC2304(52)> RESET(L) <FROM IC2304(57)> CORRECT ON(L)
C19 H2
RESET(L) CORRECT ON(L)
86-95 96 97 98 99 100 24 23 33 37 36 35 34 27 22 38 25 3 5 4
VCC(A) 15,26,53,57,61,65,69,73,82 VCC(D) 1,50

19 18 39 43 42 41 40 28 44 45 20 21 81 80 79 77 78 13
+15.5V +3.3V
12 11 10
V-REF-H(+7.5V) V-REF-L(+7V) LCDCOM TP2901
Q2003 XDIR-X <FROM IC2304 (60)> DIR-X <FROM IC2304 (59)> DIR-Y <FROM IC2304 (50)> SERIAL DATA 0 SERIAL CLOCK IC2001 CS(L) IC2002 CS(L) IC2003 CS(L) IC2505CS(L) FROM SYSTEM CONTROL BLOCK DIAGRAM LEVEL SHIFTER
H4,H5,ETC
IC2504 (BUFFER) SERIAL DATA 0 B18

2 3 7 5 4 18 17 13 15 16 14
+3.3V IC2501
VDD2(+3.3V) SERIAL CLOCK B20
D7,D8,ETC 8
+1.8V REG.
VDD1(+1.8V)
CS(L) B19
VIDEO SIGNAL PATH II BLOCK DIAGRAM PT-43LC14/PT-50LC14

61
PT-43LC14 / PT-50LC14 / PT-60LC14
VIDEO SIGNAL PATH II BLOCK DIAGRAM (Model: PT-60LC14)

LCD DRIVE C.B.A.
IC2503 (LVDS RECEIVER) IC2505 (SIGNAL PROCESS FOR LCD PANEL)
+15.5V P2001-36 P2001-35 P2001-34 P2001-33 P2001-32 P2001-31 P2001-(19-30) P2001-18 P2001-17 P2001-16 P2001-15 P2001-14 P2001-13 P2001-12 P2001-11 P2001-10 P2001-9 P2001-8 P2001-7 P2001-6 P2001-5 P2001-4 P2001-3 P2001-2 P2001-1
LCD(R)
IC2001 (SAMPLING HOLD) LVDS DATA A(+) LVDS DATA A(-) LVDS DATA B(+) LVDS DATA B(-) LVDS DATA C(+) LVDS DATA C(-) LVDS DATA D(+) LVDS DATA D(-) LVDS CLOCK(+) LVDS CLOCK(-) P2501-14 P2501-15 P2501-11 P2501-12 P2501-8 P2501-9 P2501-2 P2501-3 P2501-5 P2501-6
10 9 12 11 16 15 20 19 18 17 30,32-35, 37-39

52,54,56,58,60,62, 64,66,68,70,72,74
TP2004 TP2007
R DATA (8BIT)
A5-A7,B6-B8, C7,C8
FROM VIDEO I SIGNAL PATH BLOCK DIAGRAM

41-43,45-47, 49,50
NON UNIFORMITY COLOR COMPENSATION G DATA (8BIT)

A10-A12,B10-B12, C10,C11
W4-W6,Y1-Y7 S/H CLOCK(R) V2 XFR(R) V1 STSQO(R) W3 FRP U1
R DATA (10BIT)
GAMMA CORRECTION WHITE BALANCE CONTROL TIMING GENERATOR FOR PANEL DRIVE DY DX ENABLE 4 ENABLE 3 ENABLE 2 ENABLE 1 NRG CLX CLY
M19 Y10 V9 W9 Y9 W10 M1 W8 M18
86-95 96 97 98 99 100 24 23 33 37 36 35 34 27 22 38 25 3 5 4
VCC(A)
15,26,53,57,61,65,69,73,82
+15.5V +3.3V
VCC(D)
1,50 19 18 39 43 42 41 40 28 44 45 20 21 81 80 79 77 78 13
PLL
1-3,5,51, 53-55
B DATA (8BIT)
A15,A16,B14-B16, C14-C16
H-SYNC V-SYNC
29 27 26
E2 D2 E1
H-SYNC V-SYNC CLOCK(76 MHz) V-REF-H(+7V) V-REF-L(+5V)
12 11 10
V-REF-H(+7.5V) V-REF-L(+7V) LCDCOM
Q2006,Q2009, Q2014,Q2015, Q2020,Q2021 BUFFER
LCD(G)
P2002-36 P2002-35 P2002-34 P2002-33 P2002-32 P2002-31 P2002-36 P2002-(19-30) P2002-18 P2002-17 P2002-16 P2002-15 P2002-14 P2002-13 P2002-12 P2002-11 P2002-10 P2002-9 P2002-8 P2002-7 P2002-6 P2002-5 P2002-4 P2002-3 P2002-2 P2002-1

W15-W19,Y16-Y20 S/H CLOCK(G) W13 XFR(G) V13 STSQO(G) Y15 XFRP Y13

52,54,56,58,60,62, 64,66,68,70,72,74
TP2005
G DATA (10BIT)
IC2502 +5V
5
+3.3V REG.
13,23,31,40,48,56 4
86-95 96 97 98 99 100 24 23 33 37 36 35 34 27 22 38 25 3 5 4
VCC(A)
15,26,53,57,61,65,69,73,82
+15.5V +3.3V
VCC
VCC(D)
1,50 19 18 39 43 42 41 40 28 17 44 45 20 21 81 80 79 77 78 13
12 11 10
Q2004,Q2007, Q2010,Q2011, Q2016,Q2017 BUFFER
LCD(B)
P2003-36 P2003-35 P2003-34 P2003-33 P2003-32 P2003-31 P2003-(19-30) P2003-18 P2003-17 P2003-16 P2003-15 P2003-14 P2003-13 P2003-12 P2003-11 P2003-10 P2003-9 P2003-8 P2003-7 P2003-6 P2003-5 P2003-4 P2003-3 P2003-2 P2003-1

D20,E19,E20,F19,F20, G19,G20,H19,H20,J18

52,54,56,58,60,62, 64,66,68,70,72,74
TP2006
B DATA (10BIT)
S/H CLOCK(B) XFR(B) STSQO(B) <FROM IC2304(52)> RESET(L) <FROM IC2304(57)> CORRECT ON(L)
C19 H2
K20 K18 J19
RESET(L) CORRECT ON(L)
86-95 96 97 98 99 100 24 23 33 37 36 35 34 27 22 38 25 3 5 4
VCC(A)
15,26,53,57,61,65,69,73,82
+15.5V +3.3V
VCC(D)
1,50 19 18 39 43 42 41 40 28 44 45 20 21 81 80 79 77 78 13
12 11 10
Q2005,Q2008, Q2012,Q2013, Q2018,Q2019 BUFFER TP2901
Q2003 XDIR-X <FROM IC2304 (60)> DIR-X <FROM IC2304 (59)> DIR-Y <FROM IC2304 (50)> SERIAL DATA 0 SERIAL CLOCK IC2001 CS(L) IC2002 CS(L) IC2003 CS(L) IC2505CS(L) FROM SYSTEM CONTROL BLOCK DIAGRAM +15.5V IC2004 (SW)
5 3 2 1
H4,H5,ETC
IC2504 (BUFFER) SERIAL DATA 0

B18 B20 2 3 7 5 4 18 17 13 15 16 14
+3.3V IC2501
VDD2(+3.3V) SERIAL CLOCK
L H L H
D7,D8,ETC 8
15
+1.8V REG.
VDD1(+1.8V)
9 10
Q2001,Q2002 LEVEL SHIFTER
CS(L)
B19
VIDEO SIGNAL PATH II BLOCK DIAGRAM PT-60LC14

62
PT-43LC14 / PT-50LC14 / PT-60LC14
SD/PC CARD SIGNAL PROCESS BLOCK DIAGRAM

MAIN C.B.A.
IC9004 (SD/PC CARD SIGNAL PROCESS) +5V SD DATA(0-3)
160-162,165
CARD Y/PB/PR SIGNAL

IC9011 (+3.3V REG.)
5
P9002
4
+3.3V REG.
VCC(+3.3V) SD DATA(0-3) SD CLOCK SD WRITE PROTECT(L) SD CARD DETECT(L)
SD CARD
SD CLOCK CARD YUV DATA (0-7) CARD V-SYNC CARD H-SYNC 27MHz CLOCK CARD YUV DATA (8BIT) : 480i
106-110, 113-115 118 119
169
TO VIDEO I SIGNAL PATH BLOCK DIAGRAM
IC9207 (TRANSCEIVER) SD/PC CARD SIGNAL PROCESS

122-128,131-137, 140,141 2 3 4 5 6 7 8 9 1 DIRECTION 19 ENABLE 18 17 16 15 14 13 12 11
CARD V-SYNC CARD H-SYNC
PC DATA(0-15)
P9201 PC DATA(0-15) PC ADDRESS(0-9) PC CARD DETECT1(L) PC CARD DETECT2(L) CHIP ENABLE2 CHIP ENABLE1 OUTPUT ENABLE I/O READ CONTROL WRITE ENABLE I/O WRITE CONTROL VS1 VS2 REG RESET(L)
VCC IC9008 +6V

2 1,18,27,51,59,68,75,92, 99,104,111,130,148,157, 159,164,183,193,201
20
PC CARD
+3.5V REG.
VCC
IC9208 (TRANSCEIVER)
2 3 4 5 6 7 8 9 1 DIRECTION 19 ENABLE 18 17 16 15 14 13 12 11
+5V(PC CARD DETECTED)/0V(NO PC CARD)
IC9002 +3.3V
2
+2.8V REG.
4
9,35,44,83,121,139,172 3
VCC
VCC
20
+3.3V Q9001 PC ADDRESS 0 PC ADDRESS 1

154 155
IC9209 (BUFFER) IC9205 (D-FLIP/FLOP)

3 4 7 8 13 14 17 18 F/F F/F F/F F/F F/F F/F F/F F/F 2 5 6 9 12 15 16 19 11 2 3 4 5 6 7 8 9 19 ENABLE 18 17 16 15 14 13 12 11
IC9001 (128M SDRAM)
VCC
20
128M SDRAM 94.5MHz

1,3,9,14,27,43,49 38
SDRAM DATA (0-15) TP9001
+3.3V
77-82,85-90, 93-96 102
20
VCC IC9211 (BUFFER)

20
94.5MHz
H RESET(L)
145
IC9201 (D-FLIP/FLOP) +3.3V

16
VCC
+3.3V
VCC
F/F F/F F/F 10 12 15
11 13 14
2 3 4 5 6 7 8 9 19 ENABLE
VCC
18 17 16 15 14 13 12 11
IC9206 (OR GATE) CARD RESET(L) LCS1(L)

24 174 1 9 1 2 4 5 10 9 5 3
IC9204 (+5V REG.)

6
TP9202
4
+3.3V
IC9202 (D-FLIP/FLOP)
1 2 3 4 10 11 12 13
+6V
8
+5V REG.
1
F/F
VCC
14
+3.3V
TP9201
PC CARD ON(H)
HCS3(L) HRD
153 150
F/F
VCC
14
IC9203 (2 TO 4LINE DECODER)

1 2 3 13 14 15
+3.3V
16
IC9212 (BUFFER)
1
VCC IO/MEM
158
2 TO 4LINE DECODER
4 2 5 11 12
VCC
5 4
+3.3V IC9210 (BUFFER)

2 3 4 5 6 7 8 9 20
IC9003 (INVERTER) HWR

149
2 TO 4LINE DECODER
VCC
18 17 16 15 14 13 12 11
13
12
116
27MHz CLOCK 27MHz CLOCK 27MHz CLOCK 27MHz CLOCK
HCS1(L)
152
DATA(8-15) IC9007 (FLASH MEMORY)
X9001
1 11 10 117
27MHz OSC
2
IC9010
4 1
105
178-182,185-191, 194-197
DATA(0-15)
DATA(0-7)
FLASH MEMORY
12
PROGRAM FOR CARD PROCESSOR (IC9004)
VCC
37
+3.3V
19
ENABLE
SPECTRUM SPLITTER VCC

7
RESET(L)
49
+3.3V
14
VCC
CARD RESET(L) <FROM IC6003(43)> LCS2(L) CARD SERIAL DATA 1 CARD SERIAL CLOCK CARD CS(L) CARD READY(L)
175 142 143 166 167
+3.3V
SERIAL DATA 0 SERIAL DATA 1 SERIAL CLOCK CARD CS(L) CARD READY(L)
TO/FROM SYSTEM CONTROL BLOCK DIAGRAM
SD/PC CARD SIGNAL PROCESS BLOCK DIAGRAM PT-43LC14/PT-50LC14/PT-60LC14

63
PT-43LC14 / PT-50LC14 / PT-60LC14
AUDIO SIGNAL PATH BLOCK DIAGRAM

TUNER C.B.A. REAR JACK C.B.A. AUDIO AMP C.B.A.
IC4503 +12V 3 REG. RL4501
AUDIO SIGNAL
U7001 (MAIN TUNER) AUDIO 13 R7514 SEPARATION
IC7501 (MTS/SAP SIGNAL PROCESS) MTS/SAP SIGNAL PROCESS VCC

19
IC3502 (AUDIO SW) Q7501 B B Q7502 TP7501 P7002-7 P7002-5 TP7502 P3501-7 P3501-5
34 4 2 36 16 14 6 8 10 12
IC3501 (SOUND PROCESSOR) IC4501 (AUDIO AMP)
+16V
R-CH L-CH
29 30
21
+5V
TV LINE 1 LINE 2 LINE 3 RGB 2 DVI/RGB 1/HDMI COMPONENT 1 COMPONENT 2 COMPONENT 3 COMPONENT 4
NETWORK C.B.A. (FOR R-CH)

AUDIO INPUT SELECT (R-CH)
29 30
SOUND PROCESS (R-CH)
23
Q3502 B
P3603-3
P4505-3
11
AUDIO AMP (R-CH)
P4503-1 P4503-2 P4503-3 P4503-4
P4553-1 P4553-2
P4552-1 P4552-2
SPEAKER (R-CH) WOOFER
25
JK3501 AUDIO IN1 (R) AUDIO IN1 (L) AUDIO IN2 (R) AUDIO IN2 (L)
33 3 1 35 15 13 5 7 9 11 6
P4551-1 P4551-2
SPEAKER (R-CH) TWEETER
NETWORK C.B.A. (FOR L-CH)

P4553-1 P4553-2 P4552-1 P4552-2 SPEAKER (L-CH) WOOFER
FRONT JACK C.B.A.

JK4801 AUDIO IN3 (R) AUDIO IN3 (L) JK4802 R L P3902-11 P3902-9 P3502-11 P3502-9
TV LINE 1 LINE 2 LINE 3 RGB 2 DVI/RGB 1/HDMI COMPONENT 1 COMPONENT 2 COMPONENT 3 COMPONENT 4
AUDIO INPUT SELECT (L-CH)
30
SOUND PROCESS (L-CH)
Q3501 B
P3603-1
P4505-1
AUDIO AMP (L-CH) VEE VEE VCC

5
P4551-1 P4551-2
SPEAKER (L-CH) TWEETER
26
-16V +16V VCC 16 +9V
1 6 3
Q4504
VCC VCC P3903-2 P3903-1 P3504-2 P3504-1

31 32
RGB AUDIO IN2
Q4501 +9V
DRIVE Q4505
MAIN C.B.A.
IC4002 (SW) (R-CH) HDMI AUDIO(R) FROM VIDEO I BLOCK DIAGRAM HDMI AUDIO(L)
1 5 4
AMP MUTE(L) <FROM IC6003(13)>
HDMI RGB1 DVI (L-CH)
P3404-12
P3602-12
12 14 11
HDMI RGB1 DVI
13
P3404-14 +5V -5V
P3602-14
RGB AUDIO IN1
JK4001 R L JK4003 SWITCHING CONTROL

9 10
VCC 16 VEE 7
DVI AUDIO IN (R) DVI AUDIO IN (L) <FROM IC6003(62)> AUDIO SW CONTROL 2 <FROM IC6003(64)> AUDIO SW CONTROL 1 Q4002
Q4001
JK3601 COMPONENT AUDIO IN1 (R) COMPONENT AUDIO IN1 (L) JK3602 COMPONENT AUDIO IN2 (R) COMPONENT AUDIO IN2 (L) JK3603 COMPONENT AUDIO IN3 (R) COMPONENT AUDIO IN3 (L) JK3604 COMPONENT AUDIO IN4 (R) COMPONENT AUDIO IN4 (L) JK3502 AUDIO OUT (R) AUDIO OUT (L) Q3510 MUTE-ON Q3512 MUTE-ON
DRIVE
Q3509 LINE OUT MUTE(H) <FROM IC6003(9)>
AUDIO SIGNAL PATH BLOCK DIAGRAM PT-43LC14/PT-50LC14/PT-60LC14

64
PT-43LC14 / PT-50LC14 / PT-60LC14
SYSTEM CONTROL BLOCK DIAGRAM

REAR JACK C.B.A.
IC3501 (SOUND PROCESSOR) +9V
16
MAIN C.B.A.
IC6003 (MAIN MICROCONTROLLER) IC6007 (BUFFER) P3601-2 P3601-3 P3403-2 P3403-3 IC5803 (HDMI INTERFACE)
70 71 73
TUNER C.B.A.
U7001 (MAIN TUNER) OSD DATA 0 27 OSD DATA 1 26 OSD DATA 2 24 OSD DATA 3 23
5 2 9 12 6 3 8 11
VCC
I2C SERIAL CLOCK1 14 I2C SERIAL DATA1 13
I2C SERIAL CLOCK1 I2C SERIAL DATA1 RESET(L) I2C SERIAL CLOCK0 I2C SERIAL DATA0
OSD DATA 0 OSD DATA 1 OSD DATA 2 OSD DATA 3 +3.3V TO VIDEO I SIGNAL PATH BLOCK DIAGRAM
P6004-3 P6004-4
P7003-3 P7003-4
10 11
IC3504 (VIDEO SW) +9V

8,47,53,57
U7101 (SUB TUNER)

10 11
VCC
I2C SERIAL CLOCK0 74 I2C SERIAL DATA0 75 RESET(L) 72 IC5004 (MAIN VIDEO SIGNAL PROCESS) I2C SERIAL CLOCK0 25 I2C SERIAL DATA0 26 RESET(L) 33 IC5103 (SUB VIDEO SIGNAL PROCESS) I2C SERIAL CLOCK0 65 I2C SERIAL DATA0 64 RESET(L) 61
78 80
VCC 14 IC6008 (BUFFER)
IC3502 (AUDIO SW) +9V

31,32
VCC 14 OSD BLANKING 8

12 11
+3.3V OSD BLANKING
IC7501 (MTS/SAP SIGNAL PROCESS)

27 24
VCC
VCC 19
+5V
LCD DRIVE C.B.A.

IC2504 (BUFFER) Q6004 STANDBY(L)/NORMAL(H) 48 Q6003 Q6001 LAMP ON(H) 44 LAMP STATUS 19 Q6011 Q6002 STANDBY(L) /POWER ON(H) LAMP ON(H) LAMP STATUS TO POWER SUPPLY BLOCK DIAGRAM
17 18 14 13 15 16 3 2 6 7 5 4 D7,D8,ETC
IC2505 (COLOR CORRECTION/TIMING GENERATOR)

B20 B18 B19
SERIAL CLOCK SERIAL DATA 0 CS(L)

H4,H5,ETC
+3.3V VDD2 IC2501 VDD1

1
IC6005 (EEPROM) +5V

8
VCC LAMP TIME DATA ADJUSTMENT DATA
IC5301 (VIDEO SIGNAL PROCESS) I2C SERIAL CLOCK0 A3 I2C SERIAL DATA0 A4 RESET(L) A22
+1.8V 8 REG.
VCC 20 +3.3V
+3.3V IC2001 (SAMPLING HOLD RED)

5
IC6006 (EEPROM) +5V

8
VCC(A) 15,26,53,57,61,65,69,73,82 VCC(D) 1,50
+15.5V +3.3V
VCC SETTING DATA OF EACH IC's FOR MAIN C.B.A. USER ADJUSTMENT DATA
IC6002 +3.3V
2
3 5
RESET 1 X6001 4 MHz OSC
RESET(L)
FILTER ERROR DETECTION 65 LAMP COVER OPEN(H) 66
IC2301 (EEPROM)
2 6 5 1
75 76
OSC2 OSC1
SERIAL DATA 1 SERIAL CLOCK SERIAL DATA 0 CS(L)
ADJUSTMENT DATA/ SETTING DATA OF VCC 8 EACH IC'S FOR LCD DRIVE C.B.A.
IC2002 (SAMPLING HOLD GREEN) +5V

5 3
VCC(A) 15,26,53,57,61,65,69,73,82 VCC(D) 1,50
+15.5V +3.3V
+3.3V Q6010 +3.3V

REG.
32 77 41
VCC VCC VCC
IC2304 (LCD MICROCONTROLLER)

58 69 68 61 62 23 24 22
IC2003 (SAMPLING HOLD BLUE)

5 3 4
CARD CS(L) CARD READY(L) FROM/TO SD/PC CARD SIGNAL PROCESS BLOCK DIAGRAM IC6001 (BUFFER)
4 5 13 12
SERIAL DATA 1 SERIAL DATA 0 51 CARD READY(L) SERIAL CLOCK SUB MICROCONTROLLER CS(L)
50
CARD CS(L)
82 1 81 49
VCC 14
6 11
+3.3V
EEPROM CS(L) IC2003 CS(L) IC2002 CS(L) IC2001 CS(L) IC2505 CS(L) SERIAL DATA 1 SERIAL CLOCK SERIAL DATA 0
VCC(A) 15,26,53,57,61,65,69,73,82 VCC(D) 1,50
+15.5V +3.3V
V-REF 10 VCC 11 VCC 56
+5V
SERIAL CLOCK SERIAL DATA 1 SERIAL DATA 0
+3.3V IC6302 (SUB MICROCONTROLLER) VCC 11 IC6303 +3.3V 5 4 REG. Q6303

REG.
9 48 47
+3.3V LINE DETECT (NORMAL(H)/ABNORMAL(L)) +17V LINE DETECT (NORMAL(H)/ABNORMAL(L)) +11V LINE DETECT (NORMAL(H)/ABNORMAL(L))
TXD 39 RXD 40 +5V +11V IC2902

2 5 1
P2302-7 P2302-8
TXD RXD
RS-232C
+17V +11V STBY+9V
IC5702 (FPGA) RESET(L) 88

1,10,24,36,46,54,68, 76,78,93,100,105,114, 126,137,145,180,201
FAN 1 DRIVE 4 P2902-1 P2902-2 P2902-3 FAN 2 DRIVE 4 P2903-1 P2903-2 P2903-3 FAN 3 DRIVE 4 P2904-1 P2904-2 P2904-3
VCC 56
19 21 20 76
FAN1 ON(H) 53 SERIAL DATA 0 SERIAL CLOCK SERIAL DATA 1 SCALER CS(L) Q6302 I2C SERIAL CLOCK 38 I2C SERIAL DATA 36
2 6 7 1
SERIAL DATA 0 205 SERIAL CLOCK 203 SERIAL DATA 1 208 CS(L) 204 IC5701 (INVERTER)
+3.3V
VCC
CS(L) SERIAL DATA 0 SERIAL CLOCK SERIAL DATA 1
33 23 24 22
IC2903 IC2303 +5V B B RESET X2301 8 MHz OSC

18
RESET (L)
+1.8V
VCC
17,42,61,83,86,108, 156,174,207
FAN2 SPEED CONTROL 28 FAN2 ON(H) 55
2 5 1
Q6301
+3.3V
VCC
12 13
X1 X2
IC2904 FAN3 SPEED CONTROL 30 FAN3 ON(H) 73

2 5 1
FAN1 SPEED CONTROL 26
COVER SWITCH C.B.A.

X6302 8 MHz OSC X6301 32.768kHz OSC U6301 REMOTE SENSOR IC6301
12 13 16 15
OSC2 OSC1 XO XI IR DATA
RESET(L) 18 +3.3V LINE DETECT (NORMAL(H)/ABNORMAL(L)) +5V LINE DETECT (NORMAL(H)/ABNORMAL(L)) +6V LINE DETECT (NORMAL(H)/ABNORMAL(L)) +30V LINE DETECT (NORMAL(H)/ABNORMAL(L)) -5V LINE DETECT (NORMAL(H)/ABNORMAL(L)) +9V LINE DETECT (NORMAL(H)/ABNORMAL(L))
7 63 60 61 62 64
RESET 2
+3.3V +3.3V +5V +6V +30V -5V +9V
IC5705 (LVDS TRANSMITTER)

50
IC2503
47 48 45 46 41 42 37 38 39 40
32
OPERATION C.B.A.
+3.3V D6303 TEMP

80
FAN1 SPEED LVDS DATA A(+) CONTROL LVDS DATA A(-) LVDS DATA B(+) LVDS DATA B(-) LVDS DATA C(+) LVDS DATA C(-) LVDS DATA D(+) LVDS DATA D(-) LVDS CLOCK(+) LVDS CLOCK(-)
P5302-14 P5302-15 P5302-11 P5302-12 P5302-8 P5302-9 P5302-2 P5302-3 P5302-5 P5302-6
P2501-14 P2501-15 P2501-11 P2501-12 P2501-8 P2501-9 P2501-2 P2501-3 P2501-5 P2501-6
10 9 12 11 16 15 20 19 18 17
LVDS DATA A(+) LVDS DATA A(-) FAN1 SPEED 7 CONTROL LVDS DATA B(+) LVDS DATA B(-) LVDS DATA C(+) LVDS DATA C(-) LVDS DATA D(+) LVDS DATA D(-) LVDS CLOCK(+) LVDS CLOCK(-)
IC2905 (OP AMP)

5 6 7
SW2911 COVER SW P2502-1 P2502-2 P2912-1 P2912-2
THERMISTOR 1 C.B.A.
IC2905 (OP. AMP)
3 2
R2811 TEMPERATURE SENSOR P2303-2 P2303-1 P2811-2 P2811-1
D6701 POWER +5V Q6701 Q6702 RED GREEN P6701-6 P6701-7 P6701-3 P6701-4 P6701-5 P6701-1 P6701-2 P6305-6 P6305-7 P6305-3 P6305-4 P6305-5 P6305-1 P6305-2
78 77 46 47 48 42 43
TEMP LED ON(L) LAMP LED ON(L)
D6304 LAMP
79
(NEAR THE FAN1)
+3.3V
+3.3V P5302-18 P5302-16 P5302-17 P5302-20 P5302-19 P2501-18 P2501-16 P2501-17 P2501-20 P2501-19 P2304-2 P2304-1
KEY MATRIX
(OPERATION BUTTON)
POWER LED-R ON(L) POWER LED-G ON(L) SCAN 0 SCAN 1 SCAN 2 KEY DATA 0 KEY DATA 1
FAN(1,2,3) LOCK(H) 6 TEMPERATURE DATA 3 4 TEMPERATURE DATA 4 5 TEMPERATURE DATA 1 2 TEMPERATURE DATA 2 3
THERMISTOR 2 C.B.A.
R2821 TEMPERATURE SENSOR P2821-2 P2821-1
(NEAR THE LAMP)
SYSTEM CONTROL BLOCK DIAGRAM PT-43LC14/PT-50LC14/PT-60LC14

65
PT-43LC14 / PT-50LC14 / PT-60LC14
OPTICAL BLOCK DIAGRAM
SCREEN
Blue Light Path Green Light Path Red Light Path

MIRROR
PROJECTION UNIT
PROJECTION LENS LIGHT IN POLARIZER BLUE
LIGHT IN POLARIZER BLUE UNIT
LCD/PRISM UNIT
DICHROIC PRISM LIGHT OUT POLARIZER RED
LIGHT IN POLARIZER RED UNIT
OPTICAL BLOCK UNIT

FIELD LENS RED
(PT-60LC14) FIELD LENS BLUE (PT-43/50LC14) RELAY LENS 1
LCD BLUE
FULL MIRROR BLUE
LCD RED
FULL MIRROR RED
RELAY LENS 2
LIGHT OUT POLARIZER BLUE UV CUT FILTER ND FILTER FIELD LENS GREEN
LCD GREEN
LIGHT OUT POLARIZER GREEN
LIGHT IN POLARIZER GREEN LIGHT IN POLARIZER GREEN UNIT
CONDENSER LENS
FULL MIRROR BLUE
DICHROIC (PT-60LC14) RELAY LENS 1 MIRROR GREEN
DICHROIC MIRROR RED INTEGRATOR P/S CONVERTER LAMP
(PT-43/50LC14) RELAY LENS 1
OPTICAL BLOCK DIAGRAM PT-43LC14/PT-50LC14/PT-60LC14

66
PT-43LC14 / PT-50LC14 / PT-60LC14
10 SCHEMATIC DIAGRAMS
10.1. SCHEMATIC DIAGRAM AND CIRCUIT BOARD LAYOUT NOTES
1. Important safety notice have special Components identified by the sign characteristics important for safety. When replacing any of these components. Use only the specified parts. 2. Do not use the part number shown on this drawing for ordering. The correct part number and part value is shown in the parts list, and may be slightly different or amended since this drawing was prepared. 3. Use only original replacement parts: To maintain original function and reliability of repaired units, use only original replacement parts which are listed with their part numbers in the parts list section of the service manual. 4. Parts different in shape or size may be used. However, only interchangeable parts will be supplied as service replacement parts. 5. Test point information : Test point with a jumper wire across a hole in P.C.B. : Test point with no test pin. 3. Parts marked "PT" are not used in any models included in this service model.
Example:
C6011 100P PT
C6011 PT
R6097 PT
4. Jumper wires are used for WA10, WA5 etc and these are not supplied as replacement parts.
Circuit Board Layout Note

Circuit Board Layout shows components installed for various models. For proper parts content for the model you are servicing, please refer to the schematic diagram and parts list. NOTE: Circuit Board Layout includes components which are not used.
Schematic Diagram Notes

1. Indication for Zener Voltage of Zener Diodes The Zener Voltage of Zener Diodes are indicated as such on Schematic Diagrams. Example: (6.2V)......Zener Voltage 2. How to identify Connectors Each connector is labeled with a Connector No. and Pin No. Indicating what it is connected to, in other words, its counter part. Use the interconnection schematic diagram to find the connection between associated connectors.
Example: The connections between C.B.A.s are shown below.

Ref. No. of the connection parts such as lead cable, flexible cable which is supplied as a replacement parts.
POWER SUPPLY C.B.A. P1503
The Number of pins of the Connector.
MAIN C.B.A. P3004

244 (10 Pins) Connector No. on Main C.B.A.
SCHEMATIC DIAGRAM AND CIRCUIT BOARD LAYOUT NOTES PT-43LC14/PT-50LC14/PT-60LC14

67
PT-43LC14 / PT-50LC14 / PT-60LC14
10.2. INTERCONNECTION SCHEMATIC DIAGRAM
INTERCONNECTION SCHEMATIC DIAGRAM

IMPORTANT SAFETY NOTICE: COMPONENTS IDENTIFIED BY THE SIGN HAVE SPECIAL CHARACTERISTICS IMPORTANT FOR SAFETY. WHEN REPLACING ANY OF THESE COMPONENTS, USE ONLY THE SPECIFIED PARTS.
THERMAL FUSE UNIT REPLACEMENT NOTE: CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE SAME TYPE NUMBER LSJA0464-FE (115 ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQUES D INCENDIE N UTILISERQUE DES FUSIBLE DE MME TYPE NUMRO LSJA0464-FE (115 ) ).
NOTE: For placing a purchase order of the parts, be sure to use the part number listed in the parts list. NOTE: Do not use the part number on this diagram. FOR SCHEMATIC DIAGRAM AND CIRCUIT BOARD LAYOUT NOTES, REFER TO BEGINNING OF SCHEMATIC SECTION.
NOTE: FOR SCHEMATIC DIAGRAM AND CIRCUIT BOARD LAYOUT NOTES, NOTE: REFER TO BEGINNING OF SCHEMATIC SECTION.
NOTE: SUPPLIED AS A OPTIONAL ACCESSORY. PARTS MARKED "PT" ARE NOT USED.
THE LAMP UNIT IS NOT SUPPLIED AS A REPLACEMENT PART. WHEN REPLACING, REPLACE THE LAMP UNIT WHICH IS
TV/TUNER UNIT MAIN C.B.A. P3401 P1007 (14 Pins) POWER C.B.A. P1007 P804 P1006 (3 Pins)
73
AC CORD FAN 4
HDMI IN P805 P1001 HDMI AUDIO IN L-CH HDMI AUDIO IN R-CH BALLAST C.B.A. P1302 P1303 P1305 P1305 (4 Pins) RGB AUDIO IN 1 PT-50LC14, PT-60LC14 OPERATION C.B.A. P6701 P6701 (9 Pins) P6305 P1306 F001 115 THERMAL (239 F) FUSE UNIT FAN 2 P2903 (3 Pins) P1301 (5 Pins) P1301 LAMP UNIT P2902 (3 Pins) FAN 1 PROJECTION UNIT FAN CASE UNIT P1009 P1010 P1011 P1009 (3 Pins)
P1302 (2 Pins) RGB IN 1 P6002
LCD DRIVE C.B.A. FRONT JACK C.B.A. S-VIDEO IN 3 VIDEO IN 3 AUDIO IN 3 L-CH AUDIO IN 3 R-CH P3902 RGB IN 2 P3903 RGB AUDIO IN 2 P3902 (12 Pins) P3903 (3 Pins) P6301 (8 Pins) P6301 USED FOR ADJUSTMENT AT FACTORY ONLY P7003 UHF/VHF MAIN TUNER UHF/VHF IN P7003 (7 Pins) P6003 P3403 P3404 P3901 P3901 (10 Pins) P5501 P6001 (6 Pins) P6001 USED FOR ADJUSTMENT AT FACTORY ONLY P6007 (4 Pins) P6007 USED FOR ADJUSTMENT AT FACTORY ONLY P6008 (5 Pins) P6008 USED FOR ADJUSTMENT AT FACTORY ONLY P3402
97 (8 Pins)
LCD / PRISM UNIT LCD PANEL (RED) FAN 3 P2904 (3 Pins) LCD PANEL (GREEN)
P5302
14 (20 Pins)
P2501
P2001 (36 Pins)
P2002 (36 Pins) P2502 LCD PANEL (BLUE) P2901 P2003 (36 Pins) P2912 (2 Pins)
COVER SWITCH C.B.A. P2912
THERMISTOR 1 C.B.A. P2303 (2 Pins) P2302 (8 Pins) P2302 USED FOR ADJUSTMENT OF LCD DRIVE C.B.A. P2304
762 (2 Pins)
P2811
THERMISTOR 2 C.B.A. P2821
TUNER C.B.A.
PIN (25 Pins) PIN

758 (1 Pin)
(14 Pins) REAR JACK C.B.A. P3502 P3504 P7002 P3501 P7002 (8 Pins) P3601
(14 Pins) AUDIO AMP C.B.A. NETWORK C.B.A. P2901 (4 Pins) P4553 P4552 (2 Pins) SPEAKER (R-CH) WOOFER SPEAKER (R-CH) TWEETER SPEAKER (L-CH) WOOFER SPEAKER (L-CH) TWEETER P4501 P4503
P3602
P3603
P4505 (6 Pins)
P4505 P4551 NETWORK C.B.A. (2 Pins)
UHF/VHF SUB TUNER
COMPONENT IN 2
PB COMPONENT IN 1
PB COMPONENT IN 3
PB COMPONENT IN 4
AUDIO OUT R-CH
AUDIO OUT L-CH
COMPONENT AUDIO IN 3 R-CH
AUDIO IN 1 R-CH
AUDIO IN 2 R-CH
COMPONENT AUDIO IN 3 L-CH
AUDIO IN 1 L-CH
AUDIO IN 2 L-CH
P4553 P4552
(2 Pins)
S-VIDEO IN 1
S-VIDEO IN 2
PIN (25 Pins) PIN
VIDEO OUT
VIDEO IN 1
VIDEO IN 2
PR
PR
PR
PR
PB
P4551
(2 Pins)
INTERCONNECTION SCHEMATIC DIAGRAM PT-43LC14/PT-50LC14/PT-60LC14
68
PT-43LC14 / PT-50LC14 / PT-60LC14
10.3. FRONT JACK SCHEMATIC DIAGRAM
FRONT JACK SCHEMATIC DIAGRAM

VIDEO SIGNAL(MAIN/SUB) SUB VIDEO SIGNAL AUDIO SIGNAL
NOTE: For placing a purchase order of the parts, be sure to use the part number listed in the parts list. Do not use the part number on this diagram.
NOTE: FOR SCHEMATIC DIAGRAM AND CIRCUIT BOARD LAYOUT NOTES, REFER TO BEGINNING OF SCHEMATIC SECTION.
NOTE: PARTS MARKED "PT" ARE NOT USED.
R3914
100 JK4801 K1U412A00006 0 1 2 3 4 5 6 D3911 PT 0 D3912 PT 7 8 9 VIDEO IN3 PT
C3561 R3911
TO REAR JACK C.B.A. P3502 L3_CPS_NOSIG_L L3_S_IN_L LINE3_Y GND LINE3_C GND LINE3_V GND LINE3_L_AUDIO GND LINE3_R_AUDIO GND
75
PT
L3901
P3902 1 2 3 4 5 6 7 8 9 10 11 12 L3902 0
Y C
S-VIDEO IN3
L3903
LSJA0471 PT P4591 7 SW_IN_L 6 SW_OUT_L 5 H/P_IN_L 4 AMP_GND 3 H/P_IN_R 2 SW_IN_R 1 SW_OUT_R
JK4590 PT K2HC103A0017 7 6 1 2 3 4 5
R3912
75
D4593
R3913
PT D4592
PT R4595
HEADPHONE
75
L4801
10 11 12 13 D4801 PT D4802 PT D3913 PT AUDIO IN3(R) L3904 0 AUDIO IN3(L)
L4802
R3901
PT 75[F]
JK3901 K1FB115A0015 L3905 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 R3918 PT R3919 PT D3901 B0BD6R200002 (6.2V) R3920 PT RED GREEN BLUE NC CSYNC(MAC2) RED RETURN GREEN RETURN BLUE RETURN NC GND GND I2C DATA HSYNC VSYNC I2C SCK
TO REAR JACK C.B.A. P3504 RGB2_L_AUDIO RGB2_R_AUDIO GND
P3903 1 2 3
L4803 L4804
R3903
75[F]
0 0 D4803 D4804
R3915
R3916
L3907
PT
PT
L3908
R3917
7 6 1 2 3 4 5
RGB AUDIO IN2
RGB2_R GND RGB2_G GND RGB2_B GND RGB2_H GND RGB2_V GND
R3902
75[F]
JK4802 K2HC103A0017
TO MAIN C.B.A. P5501
P3901 1 2 3 4 5 6 7 8 9 10
L3906
RGB IN2
LSJB3129 FRONT JACK SCHEMATIC DIAGRAM PT-43LC14/PT-50LC14/PT-60LC14
69
PT-43LC14 / PT-50LC14 / PT-60LC14
10.4. NETWORK / THERMISTOR 1 / THERMISTOR 2 / OPERATION / COVER SWITCH SCHEMATIC DIAGRAMS
NETWORK SCHEMATIC DIAGRAM

(FOR L-CH SPEAKER)
J4551 WA5 TO L-CH SPEAKER (TWEETER) P4551 SP_OUT_L_TW 2 AMP_GND 1 P4552 C4551 3R3/63V R4551 PT P4553 2 1 TO AUDIO AMP C.B.A. P4503 AUDIO SIGNAL
OPERATION SCHEMATIC DIAGRAM

R6702 R6706 R6704 180 R6705
R 1 3 G
10K
TO L-CH SPEAKER (WOOFER)
R6703
R6707
10K
2 D6701 B3AGA0000072 POWER LED
LSJB3097
TO MAIN C.B.A. P6305 GND STBY5V P_LED_G P_LED_R SCAN2 SCAN1 SCAN0 KEY_IN1 KEY_IN0

(FOR R-CH SPEAKER)
AUDIO SIGNAL J4551 WA5 TO R-CH SPEAKER (TWEETER) P4551 2 1 P4552 C4551 3R3/63V R4551 PT TO AUDIO AMP C.B.A. P4503 P4553 2 P4503-1 SP_OUT_R P4503-2 AMP_GND 1
SP_OUT_R_TW AMP_GND TO R-CH SPEAKER (WOOFER)
P6701 9 8 7 6 5 4 3 2 1 SW6701 EVQ11G05R CH_UP
SW6703 EVQ11G05R VOL_UP
SW6706 EVQ11G05R INPUT
SP_OUT_R_WF 2 AMP_GND 1
LSJB3097
THERMISTOR 1 SCHEMATIC DIAGRAM

TO LCD DRIVE C.B.A. P2303 P2811 1 THERMO_4 2 THERMO_3
SW6702 EVQ11G05R CH_DOWN
SW6704 EVQ11G05R VOL_DOWN
SW6705 EVQ11G05R POWER
10K
SP_OUT_L_WF 2 AMP_GND 1
SP_OUT_L AMP_GND
P4503-3 P4503-4
100
Q6701 2SB1218A0L (LED DRIVE)
10K
LSJB3128
R2811 D4CA35030002
LSJB3136
COVER SWITCH SCHEMATIC DIAGRAM

J2911 PT

TO LCD DRIVE P2821 C.B.A. P2304 1 THERMO_2 2 THERMO_1
TO LCD DRIVE C.B.A. P2502 P2912 1 COVER SW 2 GND
SW2911 K0L1BA000070
LINK TO VOLTAGE CHART LSJB3098 NETWORK SCHEMATIC DIAGRAM THERMISTOR 1 SCHEMATIC DIAGRAM THERMISTOR 2 SCHEMATIC DIAGRAM OPERATION SCHEMATIC DIAGRAM COVER SWITCH SCHEMATIC DIAGRAM PT-43LC14/PT-50LC14/PT-60LC14
R2821 D4CE31330001
LAMP COVER SW
LSJB3137
70
PT-43LC14 / PT-50LC14 / PT-60LC14
10.5. AUDIO AMP SCHEMATIC DIAGRAM
AUDIO AMP SCHEMATIC DIAGRAM
AUDIO SIGNAL

PT 10K R4537 PT
PT 0 R4540
PT R4539
R4541
PT R4538
PT 2700
C4521 PT 0.1[KB]
PT 10/16V
C4520
C4534 C4535 PT100/6.3V
PT PT 2R7 2R7
PT 0.1[KB] C4523
R4521
R4520
J4502 PT Q4506 PT 2SB710ARS R4533
R4542
R4536 PT22
MUTE_L IC4503 C0CAAKE00013 (+12V REG.) +12V REG. 2
POWER_G
VCC
R4532
PT 330
10
PT 47K C4536 PT
3 POWER ON_H 1 2 PRE_G 3 4 5 C4522 PT 22/6.3V R4516 PT 47K IC4501 C1AA00000660 (AUDIO AMP) C4533 PT C4532 PT
R4535
PT 10K
IC4502 PT
Q4507 PT 2SD601A
PT 10/16V R4534 PT1K
PT 100/6.3V
C4514 10/50V
C4516 10/16V
Q4508 PT 2SD601A
R4517 PT 47K ( TO POWER C.B.A. P1009 P1010 P1011 P4501 ) +Vs 1 GND 2 -Vs 3 C4512 0.1 C4513 0.1 C4501 1000/35V C4502 1000/35V R4501 4700 D4501 MAZ40510MF (5.1V) R4506 15K R4508 33K C4506
-Vs +Vs -Vs
C4529
P4505 6 5 4 3 2 1 J4501 WA7.5
TO REAR JACK C.B.A. P3603
PT 1/50V[N]
GND
10
11 C4511 C4510 1/50V[N]
R4544 0 R4543 0
C4531
PT C4530
C4503 10/16V
R4502 15K
0.047[KB] R4507 R4509 15K 33K C4507 0.047[KB] 3.3V
R4503
C4508
10/16V[N]
C4526
PT
R4504
C4505
MAC16700E
D4504
C4504
TO NETWORK C.B.A. P4553 (FOR L-CH SPEAKER) TO NETWORK C.B.A. P4553 (FOR R-CH SPEAKER)
Q4504 2SD0601AHL SWITCHING AUDIO MUTE-ON
R4527
4700
820
4R7/25V
C4528
SP_OUT_L AMP_GND SP_OUT_R AMP_GND
P4503 4 3 2 1
R4526
Q4505 2SD0601AHL SWITCHING AUDIO MUTE-ON
0.1
0.1
J4505 WA5
4R7 ERX1SJ4R7P
C4527
1200
10/16V[N]
1K
R4505
R4546 0
RL4501 K6B2AGA00038
4R7 ERX1SJ4R7P
SW_IN_L SW_OUT_L H/P_IN_L AMP_GND H/P_IN_R SW_IN_R SW_OUT_R
J4504 1K R4530 WA5
R4512
470
R4529 1200 R4531
R4510
R4528
470 R4513 C4509
R4545
470
0.068[KB] R4511
470
0.068[KB]
10K
TO FRONT JACK C.B.A. P4591
P4502 PT 7 6 5 4 3 2 1
Q4501 2SD0601AHL SWITCHING AUDIO MUTE-ON R4524 PT
R4525 0
PT
1/50V[N]
PT 1/50V[N]
+-
-+
5V AMP_MUTE_L AUDIO_G AMP_R_AUDIO AUDIO_G AMP_L_AUDIO
R4519
R4518 C4518
PT 0
C4519
PT 0
LINK TO VOLTAGE CHART LSJB3092 AUDIO AMP SCHEMATIC DIAGRAM PT-43LC14/PT-50LC14/PT-60LC14
71
PT-43LC14 / PT-50LC14 / PT-60LC14
10.6. TUNER SCHEMATIC DIAGRAM
TUNER SCHEMATIC DIAGRAM

Z7001 U7001 ENGF6302GF LSJA0468 U7101 ENG36A08GF
VIDEO SIGNAL(MAIN/SUB) AUDIO SIGNAL
NC(CONTROL)
NC(CONTROL)
MAIN_TUNER
NC(AUDIO IN) NC(VIDEO IN) NC AGC_CONT AUDIO OUT VIDEO OUT NC(CH SW) AGC_VR NC(IF OUT) NC(XTAL) AGC SIF_OUT NC(BT) AFT SCK SDA BTL NC BC
SUB_TUNER
NC(VIDEO IN) NC AGC_CONT AUDIO OUT VIDEO OUT NC(IF OUT) NC(XTAL) AGC SIF_OUT NC(BT) SCK SDA AFT BTL NC
NC(AUDIO IN)
NC(CH SW) AGC_VR
BC
10
11 12 R7005 0
13
14
15
16
17
10
11 12 R7106 0
13
14
15
16
17
R7009 PT
C7003
C7012
C7103
PT C7005
PT
ESD GND
R7008 22
PT
P7001 1
PT C7004
PT C7104
PT C7105
C7112
C7009 10/16V
0.01[KB]
PT
PT C7110
C7011
C7010
Q7002 PT
C7109
C7111
L7001
L7101
10U
PT C7007 PT C7008
100 100 100
10U
PT C7107 PT C7108
R7007 PT
100
PT
PT
R7006
R7001 R7004 R7002 R7003
R7101
R7102
TP7001 WA10
TP7101 WA10
Q7001 PT
TO REAL JACK C.B.A. P3501 M_TNR_VIDEO GND S_TNR_VIDEO GND M_TNR_L_AUDIO GND M_TNR_R_AUDIO GND
P7002 1 2 3 4 5 6 7 8 R7514 R7517 D7501 PT D7502 PT 50KB 33K SEPARATION
R7103
PT
100
100
Q7101 PT
C7006
C7106
PT
C7002 1000/6.3V
C7102 1000/6.3V
R7104 22
PT
R7105 PT
C7001 2200P[KB]
C7101 2200P[KB]
PT
PT
P7003 1 2 3 4 5 6 7
TO MAIN C.B.A. P6004 S_AFC M_AFC I2C_SCK_5V I2C_DATA_5V 5V 30V GND
R7512 PT
R7515 R7516 PT 50KB PT
B/B IN
TP7501 WA10
R7501 C7501 100 100K C7509 100/6.3V PT PT 180K PT 2200 R7503 PT R7505 0.01 2R2/50V 2R2/50V 0.22[KB] 0.33/50V 10/16V 0.1[KB] 100 100K
L7501 100U
PT
PT
0.01
R7508 R7509
C7512
C7517
R7510 R7511
C7515
C7520
C7510
C7511
R7506 0
C7502
TP7502 WA10
R7502 2200
32
31
NC
R7504
30
AGC
29
R7507 C7506
28
27
IIC DECORDER
26
NC
25
GND
24
23
22
21
SIF DEMOD
C7513
20
OFFSET CANCEL STEREO FILTER
19
Vcc
18
PLL
17
PILOT DET L-R FILTER
Q7502 2SB1218A0L (BUFFER)
MATRIX & MODE SW
L+R
OFFSET CANCEL
75us DE-EMPH
INPUT VCA SIF/BB SW
L+R FILTER
PILOT CANCEL
L-R/SAP
IC7501 AN5832SA-E1V MTS/SAP SIGNAL PROCESS 1 2 3
OFFSET CANCEL
WIDEBAND EXPAND
SPECTRAL EXPAND SPECTRAL RMS DET
dbx DE-EMPH SPECTRAL FILTER WIDEBAND FILTER MUTE L-R/SAP SW
NOISE FILTER SAP OUT FILTER SAP DEMOD NOISE DET SIF/BB FOMO SAP FILTER SAP DET
WIDEBAND RMS DET IIC/PARA AGC SW
MODE
NC
10
11
12
13
14
15
16
0.022[KB]
C7519
R7513 3300
3R3/50V C7507
0.033[KB] C7518
0.33/50V C7505
0.1[KB] C7508
0.1[KB] C7516
2R2/50V
10/16V C7504
C7503
C7514
LINK TO VOLTAGE CHART LSJB3133 TUNER SCHEMATIC DIAGRAM PT-43LC14/PT-50LC14/PT-60LC14
72
PT-43LC14 / PT-50LC14 / PT-60LC14
10.7. VOLTAGE CHART
TUNER C.B.A.
PIN NO.
IC7501 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 Q7501 E C B Q7502 E C B TP7001 TP7101 TP7501 TP7502
AUDIO AMP C.B.A.

PIN NO. VOLTAGE PIN NO. VOLTAGE PIN NO. VOLTAGE
OPERATION C.B.A.
PIN NO.
Q6701 E C B Q6702 E C B
VOLTAGE
0 0.3 2.4 0.5 2.4 2.0 4.8 0 2.4 2.4 2.0 0 1.5 2.6 2.5 2.2 3.3 3.3 4.9 0 2.2 1.8 2.1 0 0 1.7 4.8 1.9 2.2 2.2 0 2.2
VOLTAGE
3.3 -2.1 3.3 3.3 3.2 2.6
PIN NO.
VOLTAGE
PIN NO.
VOLTAGE
PIN NO.
VOLTAGE
PIN NO.
VOLTAGE
PIN NO.
VOLTAGE
PIN NO.
VOLTAGE
PIN NO.
VOLTAGE
IC4501 1 -19.2 2 0 3 19.2 4 0 5 15.0 6 -19.2 7 0 8 0 9 0 10 0 11 0 IC4503 1 19.2 2 0 3 12.0 Q4501 E C B Q4504 E C B Q4505 E C B
0 15.0 0 0 12.0 0 0 12.0 0
2.9 0 2.3 2.9 0 2.3 2.6 2.8 2.9 2.9
VOLTAGE CHART PT-43LC14/PT-50LC14/PT-60LC14
73
PT-43LC14 / PT-50LC14 / PT-60LC14
74
PT-43LC14 / PT-50LC14 / PT-60LC14
11 CIRCUIT BOARD LAYOUT

11.1. FRONT JACK C.B.A. / OPERATION C.B.A. / NETWORK C.B.A.
FRONT JACK C.B.A. LSEP3129A
NOTE: CIRCUIT BOARD LAYOUT INCLUDES COMPONENTS WHICH ARE NOT USED. PLEASE REFER TO THE SCHEMATIC DIAGRAM AND PARTS LIST FOR PROPER PARTS CONTENT. NOTE: FOR SCHEMATIC DIAGRAM AND CIRCUIT BOARD LAYOUT NOTES, REFER TO BEGINNING OF SCHEMATIC SECTION.
NETWORK C.B.A. LSEP3097A

NOTE: CIRCUIT BOARD LAYOUT INCLUDES COMPONENTS WHICH ARE NOT USED. PLEASE REFER TO THE SCHEMATIC DIAGRAM AND PARTS LIST FOR PROPER PARTS CONTENT.
(COMPONENT SIDE)
12
(FOIL SIDE)
R3912 R3911
R3920
L3902
L3901
R3914 C3561 RGB2 JK3901
D3911 S
D3912
P4551 2 1 C4551
P4552 2 1
1 R3919
P3902
L3905
L3906
11
P3901
R3902 R3901
L3904
15
10
5 D3913
LINE3 JK4801
R4551 J4551
R3913
R3915 R3916
L3907
V D4804 L3903
R3903
R3917 D3901 10
L3908
2 1 P4553 LSJB3097
R3918
AUDIO JK4802
D4802
P3903
1 3
L4803
L4804
D4803
R D4801
P4591
1 L4802
R4595 D4593 D4592 7 LSJB3129 LSJB3129 HEAD PHONE JK4590
(DUAL PATTERNS) OPERATION C.B.A. LSEP3128A

(DUAL PATTERNS)
(COMPONENT SIDE)
R6707
Q6701 Q6702
EB C EB C
R6703 R6702
R6704
L4801
(FOIL SIDE)
R6706
R6705
P6701 1
POWER LED D6701 SW6705 POWER

LSJB3128
VOL. UP SW6703
VOL. DOWN SW6704
CH.UP SW6701
CH. DOWN SW6702
INPUT SW6706
LSJB3128
(DUAL PATTERNS)
75
(DUAL PATTERNS)
FRONT JACK C.B.A. LSEP3129A OPERATION C.B.A. LSEP3128A NETWORK C.B.A. LSEP3097A PT-43LC14/PT-50LC14/PT-60LC14
PT-43LC14 / PT-50LC14 / PT-60LC14
11.2. AUDIO AMP C.B.A. / THERMISTOR 1 C.B.A. / THERMISTOR 2 C.B.A. / COVER SWITCH C.B.A.
AUDIO AMP C.B.A. LSEP3092A

NOTE: CIRCUIT BOARD LAYOUT INCLUDES COMPONENTS WHICH ARE NOT USED. PLEASE REFER TO THE SCHEMATIC DIAGRAM AND PARTS LIST FOR PROPER PARTS CONTENT. NOTE: FOR SCHEMATIC DIAGRAM AND CIRCUIT BOARD LAYOUT NOTES, REFER TO BEGINNING OF SCHEMATIC SECTION.
THERMISTOR 1 C.B.A. LSEP3136A1

2 1 P2811
C4505
C4504
R2811
LSJB3136
R4505 R4504
C4534
R4512 R4510
R4509 C4507
R4507
R4508 R4506 C4506 2 R4528 R4529
THERMISTOR 2 C.B.A. LSEP3137A

J4504
C4535
C4509 C4521 R4537 R4538

C4520 R4520
R4513 C4508 R4511 10
C4510
R4533 R4517
Q4506
C BE
R4502
C BE
IC4502 10 6 1 5 R4541 R4540 C4522 C4531 R4539 R4544 R4516
D4504
R4521
C4511
IC4501 11 1
RL4501 R4527
C BE
C4503
R4503
J4502
C4526
C BE
J4505 R4530 R4531
Q4505
R4532
C4518
R4524
R4536
R4518
Q4501
D4501
C4527 C4512 4
Q4504 R4526 R4545 P4502 1 R4546
R2821
R4542
C4523
1 2 P2821 LSJB3137
C4536
C4532
C4529
Q4507 Q4508 R4535 R4534 6

EB C
C4533
C BE
R4519
C4530
R4501 C4513 C4502
R4525 C4501 R4547
P4503 1
C4519 R4543 R4548
P4505 1 3 J4501 IC4503 C4528 C4516 3 1 P4501 1
COVER SWITCH C.B.A. LSEP3098A

C4514
J2911
LSJB3092
SW2911 LAMP COVER 2 1 P2912
LSJB3098
AUDIO AMP C.B.A. LSEP3092A THERMISTOR 1 C.B.A. LSEP3136A1 THERMISTOR 2 C.B.A. LSEP3137A COVER SWITCH C.B.A. LSEP3098A PT-43LC14/PT-50LC14/PT-60LC14
76
PT-43LC14 / PT-50LC14 / PT-60LC14
11.3. TUNER C.B.A.
TUNER C.B.A. LSEP3133A
P7003 1
C7102
P7002 1
L7101 TP7001 R7009 R7008 1 R7106 C7101 Q7002

EB C
R7105
TP7101
L7501
L7001 R7515 SEPARATION R7514 17
C7509
R7502 R7501
TP7502
C7501
TP7501
R7507
C7506
EB C
EB C
C7513 C7517 C7512
C7103 C7104 C7105 C7106 C7107 C7108 C7109 C7110 C7112
R7516
R7512
D7502
R7517 C7009 R7006 C7008 C7007 Q7001 C7006 EB C C7005 C7004 C7003
R7004
C7012 C7011 C7010 R7003 R7002 R7001
D7501 R7509 R7511 R7513 C7519
C7111 R7104 Q7101 17

EB C
R7505 R7506 R7503 R7504
R7007
R7101 R7102 R7103
R7510
R7508
C7510
C7511
Q7502 Q7501
C7515
32 C7502 1 IC7501
17 16
C7520 C7002
C7518
U7101 UHF/VHF TUNER/TV DEMODULATOR UNIT
C7001
C7514
C7507 C7508
C7503 C7504 C7505
C7516
P7001
U7001 UHF/VHF TUNER/TV DEMODULATOR UNIT
R7005
LSJB3133
TUNER C.B.A. LSEP3133A PT-43LC14/PT-50LC14/PT-60LC14
77
PT-43LC14 / PT-50LC14 / PT-60LC14
78
PT-43LC14 / PT-50LC14 / PT-60LC14
12 EXPLODED VIEWS
12.1. MAIN PARTS SECTION
79
PT-43LC14 / PT-50LC14 / PT-60LC14
12.2. FRONT AND BASE SECTION
80
PT-43LC14 / PT-50LC14 / PT-60LC14
12.3. DISPLAY SECTION

(Models: A, B)
81
PT-43LC14 / PT-50LC14 / PT-60LC14
(Model: C)
82
PT-43LC14 / PT-50LC14 / PT-60LC14
12.4. SCREEN SECTION

(Models: A, B)
83
PT-43LC14 / PT-50LC14 / PT-60LC14
(Model: C)
84
PT-43LC14 / PT-50LC14 / PT-60LC14
12.5. PROJECTION SECTION
85
PT-43LC14 / PT-50LC14 / PT-60LC14
12.6. TV AND TUNER SECTION
86
PT-43LC14 / PT-50LC14 / PT-60LC14
12.7. PACKING PARTS AND ACCESSORIES SECTION
87
PT-43LC14 / PT-50LC14 / PT-60LC14
12.8. OPTIONAL ACCESSORY SECTION

(Model: TY-43LC14C)
88
PT-43LC14 / PT-50LC14 / PT-60LC14
(Models: TY-50LC14C, TY-60LC14C)
89
PT-43LC14 / PT-50LC14 / PT-60LC14
13 REPLACEMENT PARTS LIST

BEFORE REPLACING PARTS, READ THE FOLLOWING:
13.1.3.
Electrical Replacement Notes
1. Unless otherwise specified;
13.1. REPLACEMENT NOTES

13.1.1. General Notes
1. Use only original replacement parts: To maintain original function and reliability of repaired units, use only original replacement parts which are listed with their part numbers in the parts list. 2. IMPORTANT SAFETY NOTICE Components identified by the sign have special characteristics important for safety. When replacing any of these components, use only the specified parts. 3. SPECIAL NOTE All integrated circuits and many other semiconductor devices are electrostatically sensitive and therefore require the special handling techniques described under the "ELECTROSTATICALLY SENSITIVE (ES) DEVICES" section of this service manual. 4. Parts with no Ref. No. in "EXPLODED VIEWS" are not supplied. And some Ref. No. will be skipped. Be sure to make your orders of replacement parts according to the parts list. 5. Parts different in shape or size may be used. However, only interchangeable parts will be supplied as service replacement parts. 6. Definition of Parts supplier: a. Parts with mark "MKE" in the Remarks column are supplied from MKE. b. Parts without mark in the Remarks column are supplied from MKA. 7. Item numbers with capital letter E (Example: E10, E20,...) in the Ref. No. column are shown in the exploded views. 8. Parts whose Ref. Nos. are the same are interchangeable as replacement parts. Any of these parts may be ordered and used as a replacement part.
All resistors are in , K = 1,000 , M = 1,000 k. 2. Abbreviation RTL: Retention Time Limited This indicates that the retention time is limited for this item. After the discontinuation of this item in production, it will no longer be available. Non Repairable Board Assy Metal Glaze Film Chip Ceramic Chip Complex Component Wirewound Flameproof Circuit Board Assembly Printed Circuit Board Electrostatically Sensitive Devices
NR: MGF CHIP: C CHIP: COMPLX CMP: W FLMPRF: C.B.A.: P.C.B.: E.S.D.:
3. When replacing 0 resistor, a wire can be substituted for it. 4. Since MAIN TUNER,UHF/VHF and SUB TUNER,UHF/VHF (Ref. No. 756 and 757) have already been pre-adjusted at the factory, do not try to adjust them. The replacement parts for them are available as a complete assembly unit only.
13.1.2.
Main Parts Replacement Notes
1. Section No. of parts shown in Exploded Views are indicated in the Remarks column. 2. Abbreviation RTL: Retention Time Limited This indicates that the retention time is limited for this item. After the discontinuation of this item in production, it will no longer be available. 3. After replacing the Projection Unit (Ref. No. 21), be sure to perform "ADJUSTMENT of the Projection Unit." Refer to "WHEN REINSTALLING THE PROJECTION UNIT INTO THE UNIT AT THE USERS LOCATION"; in ADJUSTMENT PROCEDURES 1. 4. The Infrared Remote Control Unit (Ref. No. 109) replacement part is available as a complete assembly unit only. Do not try to disassemble the Infrared Remote Control Unit. 90
PT-43LC14 / PT-50LC14 / PT-60LC14
13.2. MECHANICAL REPLACEMENT PARTS LIST
Definition of Parts supplier: 1. Parts with mark "MKE" in the Remarks column are supplied from MKE. 2. Parts without mark in the Remarks column are supplied from MKA.
MECHANICAL REPLACEMENT PARTS
Ref. No. 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 21 21 22 22 22 23 24 25 25 26 31 32 33 34 35 36 38 39 40 41 42 44 44 Part No. LSYK1384 LSYK1406 LSXY0507 LSXA0531 LSQL1662 LSGL0390 LSMA0688 LSMA0697 LSMA0696 LSYK1382 LSKG0043 LSYY0147 LSKF0573 LSYK1383 LSJA0467 LSSC0648 LSMA0686 LSGV0086 STL450-3-1BK SLCSE2-500-3 LSXA0478 LSXA0571-HB LSXA0572-HB LSXA0573-HB LSYK1378 LSYK1403 LSYK1405 TMM14414 FBL12G12L2CS LSXY0618 LSXY0633 LSGV0073 EASG5PH519A2 EASG10P581A2 LSMF0290 LSGQ0088 LSGQ0089 TMMJ058 LSGQ0109 LSGQ0110 LSMG0147 LSKG0045 LSXU0014 LSJH0077 LSJH0066 Part Name & Description BASE BODY UNIT ( A,B ) BASE BODY UNIT ( C ) EXAUST FAN UNIT TOP DUCT 3 UNIT CAUTION LABEL INFRARED PIECE LAMP COVER FIX PLATE,STEEL DISPLAY SUPPORT PLATE R,STEEL DISPLAY SUPPORT PLATE L,STEEL FRONT COVER UNIT FRONT SIDE COVER L SD DOOR UNIT OPTICAL COVER LAMP COVER UNIT 20PIN CABLE GROUNDING PLATE A,STEEL REAR SUPORT PLATE,STEEL REAR COVER CLAMPER CLAMPER CLAMPER UNIT PROJECTION UNIT ( A ) Remarks
2 2 5 5 1 2 2 2 2 1 2 1 1 2 1 1 1 1 1 1 1 5 MKE PROJECTION UNIT ( B ) 5 MKE PROJECTION UNIT ( C ) 5 MKE SCREEN UNIT ( A ) 3,4 SCREEN UNIT ( B ) 3,4 SCREEN UNIT ( C ) 3,4 STRIKE 1 FAN3 5 TV/TUNER UNIT ( A ) 1,6 TV/TUNER UNIT ( B,C ) 1,6 60 REAR COVER ( C ) 1 TWEETER 3 WOOFER 3 SPACER 3 SPEAKER BOX FRONT 3 SPEAKER BOX REAR 3 SPEAKER RUBBER 3 SPACER ( C ) 4 SPACER ( C ) 4 STRING FOR SCREEN SPACER ( B 4 ) FRONT SIDE COVER R 2 OPERATION BUTTON UNIT 2 SIDE JACK HOLDER ( A ) 2 SIDE JACK HOLDER ( B,C ) 2
RTL RTL RTL
RTL RTL
Ref. No. 51 51 51 52 52 52 53 53 53 54 54 54 55 55 55 56 57 57 57 58 58 58 59 59 60 60 60 61 62 62 63 63 64 64 65 66 66 66 67 68 69 72 73 74 75 76 77 78 79 80 81 83 84 85 95 96 96 97 101 101 101 102 102 102 103 103 103 104 104
Part No. LSGY0226 LSGY0230 LSGY0231 LSGP0410 LSGP0365 LSGP0373 LSGP0411 LSGP0431 LSGP0374 LSXA0567 LSXA0548 LSXA0541 LSXA0568 LSXA0549 LSXA0542 TBM2AA0071-1 LSGV0085 LSGV0056 LSGV0091 LSDL0277 LSDL0278 LSDL0247 LSMF0280 LSMF0337 LSMF0320 LSMF0338 LSMF0311 LSGQ0092 LSYF0541 LSYF0543 LSMA0700 LSMA0715 LSMF0347 LSMF0288 LSMF0289 LSJA0535 LSJA0474 LSJA0475 LSMF0291 LSMF0292 TMM77409 LSMA0755 LSJA0531 LSJH0072 LSSC0672 LSMP0440 LSMA0693 LSMA0694 LSMA0695 LSSC0646 LSMA0690 TMM5439-1 TMM7464-1 TMM6425-1 LSMZ0376 LSGH0048 LSGH0049 LSJA0530 LSPG1740 LSPG1765 LSPG1772 LSPG1741 LSPG1548 LSPG1605 LSPN0476 LSPN0496 LSPN0418 LSPN0477 LSPN0497
Part Name & Description ESCUTCHEON ( A ) ESCUTCHEON ( B ) ESCUTCHEON ( C ) LENTICULAR SCREEN ( A ) LENTICULAR SCREEN ( B ) LENTICULAR SCREEN ( C ) FRESNEL LENS ( A ) FRESNEL LENS ( B ) FRESNEL LENS ( C ) SCREEN ANGLE H UNIT ( A ) SCREEN ANGLE H UNIT ( B ) SCREEN PLATE H UNIT ( C ) SCREEN ANGLE V UNIT ( A ) SCREEN ANGLE V UNIT ( B ) SCREEN PLATE V UNIT ( C ) BADGE,ABS RESIN BACK COVER ( A ) BACK COVER ( B ) BACK COVER ( C ) MIRROR ( A ) MIRROR ( B ) MIRROR ( C ) SPACER ( A,C ) SPACER ( B ) SPACER ( A ) SPACER ( B ) SPACER ( C ) MIRROR HOLDER H MIRROR HOLDER V UNIT ( A,B ) MIRROR HOLDER V UNIT ( C ) BACK COVER PLATE,STEEL ( B ) BACK COVER PLATE,STEEL ( C ) SPACER ( A ) SPACER ( B,C ) SPACER CONENCTOR CABLE W/PLUG ( A ) CONENCTOR CABLE W/PLUG ( B ) CONNECTOR CABLE W/PLUG ( C ) SPACER SPACER CLAMPER TNR PCB FRAME AC CORD W/PLUG REAR JACK HOLDER EARTH PLATE C PCB FRAME PCB FRAME PLATE LEFT,STEEL PCB FRAME PLATE RIGHT,STEEL PCB FRAME PLATE CENTER,STEEL BOTTOM SHIELD PLATE,STEEL MAIN PCB FRAME CLAMPER CLAMPER CLAMPER HDMI SHEET REAR JACK SHEET ( A ) REAR JACK SHEET ( B,C ) CONNECTOR CABLE W/PLUG CARTON BOX ( A ) CARTON BOX ( B ) CARTON BOX ( C ) CARTON BOX BOTTOM ( A ) CARTON BOX BOTTOM ( B ) CARTON BOX BOTTOM ( C ) CUSHION TOP LEFT,STYROFORM ( A ) CUSHION TOP LEFT,STYROFORM ( B ) CUSHION TOP LEFT,STYROFORM ( C ) CUSHION TOP RIGHT,STYROFORM ( A ) CUSHION TOP RIGHT,STYROFORM ( B )
Remarks 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 1 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 7 7 7 7 7 7 7 7 7 7 7
91
PT-43LC14 / PT-50LC14 / PT-60LC14
Ref. No. 104 105 105 105 106 106 106 107 107 107 108 108 109 110 111 113 252 253 255 330 331 332 333 401 402 406 411 417 421 435 451 452 454 455 456 464 465 466 477 478 714 751 756 757 758 759 762 E10 E10 E20 E30 E40 E50 E60 E70 E80 E90 E100 E120 E130
Part No. LSPN0419 LSPN0478 LSPN0498 LSPN0420 LSPN0479 LSPN0499 LSPN0421 LSPG1742 LSPG1549 LSPG1604 LSPF0054 LSPF0111 EUR7627Z20 LSJA0239 LSQF0834 LSPN0430 LSJA0464 LSMP0420 L6FAKCDH0007 LSMF0269 LSMF0270 LSMF0271 LSMF0272 XTV4+16A XTV3+8J XTV3+10J XYE3+FF8 XYN3+K10 XTV3+8G XTV3+20J XTW3+8Q XTV3+8F XTV4+16AFZ XTV3+12J XTV3+6F XTV4+20A XTV4+12A XTV3+10G LSHD0100 LSHD0099 VMTS0035 J0KA00000044 ENGF6302GF ENG36A08GF LSJA0468 LSSC0634 LSJA0533 LSXY0629 LSXY0641 LSEP3130A LSEB3131A LSEP3129A LSXY0620 LSEP3133A LSEP3092A LSEP3128A LSEP3097A LSEP3098A LSEP3136A LSEP3137A
Part Name & Description CUSHION TOP RIGHT,STYROFORM ( C ) CUSHION BOTTOM LEFT,STYROFORM ( A ) CUSHION BOTTOM LEFT,STYROFORM ( B ) CUSHION BOTTOM LEFT,STYROFORM ( C ) CUSHION BOTTOM RIGHT,STYROFORM ( A ) CUSHION BOTTOM RIGHT,STYROFORM ( B ) CUSHION BOTTOM RIGHT,STYROFORM ( C ) INSIDE CARTON ( A ) INSIDE CARTON ( B ) INSIDE CARTON ( C ) BAG,POLYETHYLENE ( A ) BAG,POLYETHYLENE ( B,C ) INFRARED REMOTE CONTROL UNIT VGA CABLE W/PLUG FAN BAG FRONT CUSHION ( B ) THERMAL FUSE UNIT SENSOR HOLDER FAN4 TOP DUCT 3 SPONGE 1 TOP DUCT 3 SPONGE 2 TOP DUCT 3 SPONGE 3 TOP DUCT 3 SPONGE 4 TAPPING SCREW,STEEL TAPPING SCREW,STEEL TAPPING SCREW,STEEL SCREW W/WASHER,STEEL SCREW,STEEL TAPPING SCREW,STEEL TAPPING SCREW,STEEL SCREW,STEEL TAPPING SCREW,STEEL TAPPING SCREW,STEEL SCREW,STEEL TAPPING SCREW,STEEL TAPPING SCREW,STEEL ( C ) TAPPING SCREW,STEEL TAPPING SCREW,STEEL SCREW,STEEL SCREW,STEEL CUSHION,RUBBER FERRITE CORE MAIN TUNER,UHF/VHF NR SUB TUNER,UHF/VHF NR CONNECTOR CABLE W/PLUG HEAT SINK CONNECTOR CABLE W/PLUG MAIN C.B.A. ( A ) MAIN C.B.A. ( B,C ) POWER C.B.A. BALLAST C.B.A. NR FRONT JACK C.B.A. REAR JACK C.B.A. TUNER C.B.A. AUDIO AMP C.B.A. OPERATION C.B.A. NETWORK C.B.A. COVER SWITCH C.B.A. THERMISTOR 1 C.B.A. THERMISTOR 2 C.B.A.
Remarks 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 5 MKE 5 MKE 6 5 5 5 5 1,2,3 1,2,5,6 3 6 6 2,5 6 1 1 1,2 5 5 MKE 1 4 6 3 3 6 2,6 6 6 6 6 5 MKE 6 RTL 6 RTL 6 RTL 1 2 RTL 6 RTL 6 RTL 6 RTL 2 RTL 3 RTL 2 RTL 5 RTL MKE 5 RTL MKE
13.3. OPTIONAL ACCESSORY REPLACEMENT PARTS LIST

Definition of Parts supplier: 1. All parts are supplied from MKA.
13.3.1.
Ref. No. 312 313 321 322 323 324 325 460 480
TV STAND (TY-43LC14C)
Part No. Part Name & Description SIDE PANEL L SIDE PANEL R SHELF PANEL INSTRUCTION BOOK SHELF ANGLE SIDE SHELF ANGLE CENTER CONNECTING ANGLE TAPPING SCREW,STEEL SCREW,STEEL Remarks 8 8 8 8 8 8 8 8 8
LSGP0420 LSGP0421 LSGP0364 LSQT0841-A LSXA0535 LSXA0536 LSMA0701 XTV4+25AK LSHD0090
13.3.2.
Ref. No. 321 322 323 325 480 481
Part No. Part Name & Description SHELF PANEL INSTRUCTION BOOK SHELF ANGLE SIDE CONNECTING ANGLE SCREW,STEEL SCREW,STEEL Remarks 8 8 8 8 8 8
LSGP0417 LSQT0843-A LSXA0613 LSMA0773 LSHD0090 XSN5+20
13.3.3.
Ref. No. 321 322 323 325 480 481
Part No. Part Name & Description SHELF PANEL INSTRUCTION BOOK SHELF ANGLE SIDE CONNECTING ANGLE SCREW,STEEL SCREW,STEEL Remarks 8 8 8 8 8 8
LSGP0424 LSQT0843-A LSXA0613 LSMA0774 LSHD0090 XSN5+20
13.3.4.
Ref. No.2 320
LAMP UNIT
Part No. Part Name & Description LAMP UNIT Remarks 5 NOTE
TY-LA1000
NOTE: The Lamp Unit (TY-LA1000) is not supplied as a replacement part. It is sold separately. To purchase a replacement, call the Panasonic accessory department.
92
PT-43LC14 / PT-50LC14 / PT-60LC14
13.4. ELECTRICAL REPLACEMENT PARTS LIST
Ref. No. L4803 L4804
Part No. ERJ3GEY0R00V ERJ3GEY0R00V
Part Name & Description MGF CHIP 1/16W 0 MGF CHIP 1/16W 0
Remarks
PIN HEADERS
Ref. No. P3901 P3902 P3903 Part No. LSJA0526 LSJA0470 LSJA0528 Part Name & Description CONNECTOR CABLE W/PLUG CONNECTOR CABLE W/PLUG,5V CONNECTOR CABLE W/PLUG Remarks
JACKS
Ref. No. JK3901 JK4801 JK4802 Part No. K1FB115A0015 K1U412A00008 K2HC103A0017 Part Name & Description D-SUB MINI JACK SOCKET S-JACK SOCKET EARPHONE JACK SOCKET Remarks
Definition of Parts supplier: 1. Parts with mark "MKE" in the Remarks column are supplied from MKE. 2. Parts without mark in the Remarks column are supplied from MKA.
PRINTED CIRCUIT BOARD ASSEMBLY
Ref. No. E10 E10 E20 E30 E40 E50 E60 E70 E80 E90 E100 E120 E130 Part No. LSXY0629 LSXY0641 LSEP3130A LSEB3131A LSEP3129A LSXY0620 LSEP3133A LSEP3092A LSEP3128A LSEP3097A LSEP3098A LSEP3136A LSEP3137A Part Name & Description MAIN C.B.A. ( A ) MAIN C.B.A. ( B,C ) POWER C.B.A. BALLAST C.B.A. NR FRONT JACK C.B.A. REAR JACK C.B.A. TUNER C.B.A. AUDIO AMP C.B.A. OPERATION C.B.A. NETWORK C.B.A. COVER SWITCH C.B.A. THERMISTOR 1 C.B.A. THERMISTOR 2 C.B.A. Remarks E.S.D. RTL E.S.D. RTL RTL RTL RTL RTL RTL RTL RTL RTL RTL MKE RTL MKE
MISCELLANEOUS
Ref. No. 751 Part No. J0KA00000044 Part Name & Description FERRITE CORE Remarks
13.4.2.
Ref. No. IC7501
TUNER C.B.A.
INTEGRATED CIRCUITS
Part No. Part Name & Description IC, LINEAR Remarks
AN5832SA-E1V
TRANSISTORS
Ref. No. Q7501 Q7501 Q7501 Q7502 Q7502 Q7502 Part No. 2SB1218A0L B1ADCF000063 B1ADCF000075 2SB1218A0L B1ADCF000063 B1ADCF000075 Part Name & Description TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR SI SI SI SI SI SI PNP PNP PNP PNP PNP PNP CHIP CHIP CHIP CHIP CHIP CHIP Remarks
RESISTORS
Ref. No. R7001 R7002 R7003 R7004 R7005 R7008 R7101 R7102 R7103 R7104 R7106 R7501 R7502 R7504 R7506 R7508 R7509 R7510 R7511 R7513 R7514 R7517 Part No. ERJ3GEYJ101V ERJ3GEYJ101V ERJ3GEYJ101V ERJ3GEY0R00V ERJ3GEY0R00V ERJ3GEYJ220V ERJ3GEYJ101V ERJ3GEYJ101V ERJ3GEYJ101V ERJ3GEYJ220V ERJ3GEY0R00V ERJ3GEYJ222V ERJ3GEYJ222V ERJ3GEY0R00V ERJ3GEY0R00V ERJ3GEYJ101V ERJ3GEYJ104V ERJ3GEYJ101V ERJ3GEYJ104V ERJ3GEYJ332V EVNCYAA03B54 ERJ3GEYJ333V Part Name & Description MGF CHIP MGF CHIP MGF CHIP MGF CHIP MGF CHIP MGF CHIP MGF CHIP MGF CHIP MGF CHIP MGF CHIP MGF CHIP MGF CHIP MGF CHIP MGF CHIP MGF CHIP MGF CHIP MGF CHIP MGF CHIP MGF CHIP MGF CHIP VARIABLE MGF CHIP 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 50K 1/16W 100 100 100 0 0 22 100 100 100 22 0 2.2K 2.2K 0 0 100 100K 100 100K 3.3K 33K Remarks
13.4.1.
Ref. No. D3901
FRONT JACK C.B.A.

DIODES
Part No. Part Name & Description DIODE ZENER 6.2V Remarks
B0BD6R200002
RESISTORS
Ref. No. R3901 R3902 R3903 R3911 R3912 R3913 R3914 R3915 R3916 R3917 Part No. ERJ6ENF75R0V ERJ6ENF75R0V ERJ6ENF75R0V ERJ6GEYJ750V ERJ6GEYJ750V ERJ6GEYJ750V ERJ6GEYJ101V ERJ3GEY0R00V ERJ3GEY0R00V ERJ3GEY0R00V MGF MGF MGF MGF MGF MGF MGF MGF MGF MGF Part Name & Description CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/16W 1/16W 1/16W 75 75 75 75 75 75 100 0 0 0 Remarks
COILS
Ref. No. L3901 L3902 L3903 L3904 L3905 L3906 L3907 L3908 L4801 L4802 Part No. ERJ3GEY0R00V ERJ3GEY0R00V ERJ3GEY0R00V ERJ3GEY0R00V ERJ3GEY0R00V ERJ3GEY0R00V ERJ3GEY0R00V ERJ3GEY0R00V ERJ3GEY0R00V ERJ3GEY0R00V MGF MGF MGF MGF MGF MGF MGF MGF MGF MGF Part Name & Description CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 0 0 0 0 0 0 0 0 0 0 Remarks
CAPACITORS
Ref. No. C7001 C7002 C7009 C7011 C7101 C7102 C7501 C7502 Part No. ECJ1VB1H222K ECA0JM102B ECEA1CKA100 ECJ1VB1H103K ECJ1VB1H222K ECA0JM102B ECJ1VF1H103Z ECEA1HKA2R2 Part Name & Description C CHIP 50V 0.0022UF ELECTROLYTIC 6.3V 1000UF ELECTROLYTIC 16V 10UF C CHIP 50V 0.01UF C CHIP 50V 0.0022UF ELECTROLYTIC 6.3V 1000UF C CHIP 50V 0.01UF ELECTROLYTIC 50V 2.2UF Remarks
93
PT-43LC14 / PT-50LC14 / PT-60LC14
Ref. No. C7503 C7504 C7505 C7507 C7508 C7509 C7510 C7513 C7514 C7515 C7516 C7517 C7518 C7519 C7520
Part No. ECEA1CKA100 ECEA1HKAR33 ECEA1HKA3R3I ECJ1VB1C104K ECJ1VB1E223K ECEA0JKA101 ECEA1HKA2R2 ECEA1CKA100 ECJ1VB1C104K ECJ1VF1H103Z ECJ1VB1E333K ECJ1VB1A224K ECEA1HKA2R2 ECJ1VB1C104K ECEA1HKAR33
Part Name & Description ELECTROLYTIC 16V 10UF ELECTROLYTIC 50V 0.33UF ELECTROLYTIC 50V 3.3UF C CHIP 16V 0.1UF C CHIP 25V 0.022UF ELECTROLYTIC 6.3V 100UF ELECTROLYTIC 50V 2.2UF ELECTROLYTIC 16V 10UF C CHIP 16V 0.1UF C CHIP 50V 0.01UF C CHIP 25V 0.033UF C CHIP 10V 0.22UF ELECTROLYTIC 50V 2.2UF C CHIP 16V 0.1UF ELECTROLYTIC 50V 0.33UF
Remarks
Ref. No. R4508 R4509 R4510 R4511 R4512 R4513 R4525 R4526 R4527 R4543 R4544 R4545 R4546
Part No. ERJ6GEYJ333V ERJ6GEYJ333V ERJ6GEYJ471V ERJ6GEYJ471V ERJ6GEYJ471V ERJ6GEYJ471V ERJ6GEY0R00V ERJ6GEYJ821V ERJ6GEYJ472V ERJ6GEY0R00V ERJ6GEY0R00V ERJ6GEY0R00V ERJ6GEY0R00V MGF MGF MGF MGF MGF MGF MGF MGF MGF MGF MGF MGF MGF
Part Name & Description CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 33K 33K 470 470 470 470 0 820 4.7K 0 0 0 0
Remarks
CAPACITORS
Ref. No. C4501 C4502 C4503 C4504 C4505 C4506 C4507 C4508 C4509 C4510 C4511 C4512 C4513 C4514 C4516 C4526 C4527 C4528 Part No. ECA1VM102B ECA1VM102B ECEA1CKA100 ECQB1H104KF ECQB1H104KF ECJ2VB1E473K ECJ2VB1E473K ECJ2VB1E683K ECJ2VB1E683K ECEA1HKN010B ECEA1HKN010B ECJ2VF1H104Z ECJ2VF1H104Z ECA1HM100B ECEA1CKA100 ECEA1CKN100 ECEA1CKN100 ECEA1EKA4R7 Part Name & Description ELECTROLYTIC 35V 1000UF ELECTROLYTIC 35V 1000UF ELECTROLYTIC 16V 10UF POLYESTER 50V 0.1UF POLYESTER 50V 0.1UF C CHIP 25V 0.047UF C CHIP 25V 0.047UF C CHIP 25V 0.068UF C CHIP 25V 0.068UF ELECTROLYTIC 50V 1UF ELECTROLYTIC 50V 1UF C CHIP 50V 0.1UF C CHIP 50V 0.1UF ELECTROLYTIC 50V 10UF ELECTROLYTIC 16V 10UF ELECTROLYTIC 16V 10UF ELECTROLYTIC 16V 10UF ELECTROLYTIC 25V 4.7UF Remarks
COILS
Ref. No. L7001 L7101 L7501 Part No. VLQSAB7D100K VLQSAB7D100K ELESN101KA Part Name & Description COIL 10UH COIL 10UH COIL 100UH Remarks
PIN HEADERS
Ref. No. P7002 P7003 Part No. LSJA0524 LSJA0525 Part Name & Description CONNECTOR CABLE W/PLUG CONNECTOR CABLE W/PLUG Remarks
MISCELLANEOUS
Ref. No. 756 757 758 Part No. ENGF6302GF ENG36A08GF LSJA0468 Part Name & Description MAIN TUNER,UHF/VHF NR SUB TUNER,UHF/VHF NR CONNECTOR CABLE W/PLUG Remarks
13.4.3.
Ref. No. IC4501 IC4503
AUDIO AMP C.B.A.

INTEGRATED CIRCUITS
Part No. Part Name & Description IC, LINEAR IC, LINEAR Remarks Ref. No. P4501 P4503 P4505 Part No. K1KA03A00008 K1KA04A00192 LSJA0473
PIN HEADERS
Part Name & Description CONNECTOR 3P CONNECTOR 2P CONNECTOR CABLE W/PLUG Remarks
C1AA00000660 C0CAAKE00013
TRANSISTORS
Ref. No. Q4501 Q4501 Q4501 Q4504 Q4504 Q4504 Q4505 Q4505 Q4505 Part No. 2SD0601AHL B1ABCF000011 B1ABCF000106 2SD0601AHL B1ABCF000011 B1ABCF000106 2SD0601AHL B1ABCF000011 B1ABCF000106 Part Name & Description TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR SI SI SI SI SI SI SI SI SI NPN NPN NPN NPN NPN NPN NPN NPN NPN CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP CHIP Remarks
RELAY
Ref. No. RL4501 Part No. K6B2AGA00038 Part Name & Description RELAY Remarks
MISCELLANEOUS
Ref. No. 83 417 466 714 759 Part No. TMM5439-1 XYN3+K10 XTV3+10G VMTS0035 LSSC0634 Part Name & Description CLAMPER SCREW,STEEL TAPPING SCREW,STEEL CUSHION,RUBBER HEAT SINK Remarks
DIODES
Ref. No. D4501 D4501 D4501 D4504 D4504 Part No. MAZ40510MF HZS5C2TD HZS5C3TD MA2C16700E B0AAEL000001 Part Name & Description DIODE DIODE DIODE DIODE DIODE ZENER 5.1V ZENER 5.1V ZENER 5.1V SI SI Remarks
13.4.4.
Ref. No. Q6701 Q6701 Q6701 Q6702 Q6702 Q6702
OPERATION C.B.A.
TRANSISTORS
Part No. Part Name & Description TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR SI SI SI SI SI SI PNP PNP PNP PNP PNP PNP CHIP CHIP CHIP CHIP CHIP CHIP Remarks
RESISTORS
Ref. No. R4501 R4502 R4503 R4504 R4505 R4506 R4507 Part No. ERJ6GEYJ472V ERJ6GEYJ153V ERJ6GEYJ103V ERX1SJ4R7P ERX1SJ4R7P ERJ6GEYJ153V ERJ6GEYJ153V Part Name & Description MGF CHIP 1/10W MGF CHIP 1/10W MGF CHIP 1/10W METAL OXIDE 1W METAL OXIDE 1W MGF CHIP 1/10W MGF CHIP 1/10W 4.7K 15K 10K 4.7 4.7 15K 15K Remarks
2SB1218A0L B1ADCF000063 B1ADCF000075 2SB1218A0L B1ADCF000063 B1ADCF000075
DIODES
Ref. No. D6701 Part No. B3AGA0000072 Part Name & Description LIGHT EMITTING DIODE GREEN Remarks
94
PT-43LC14 / PT-50LC14 / PT-60LC14
RESISTORS
Ref. No. R6702 R6703 R6704 R6705 R6706 R6707 Part No. ERJ6GEYJ103V ERJ6GEYJ103V ERJ6GEYJ181V ERJ6GEYJ101V ERJ6GEYJ103V ERJ6GEYJ103V MGF MGF MGF MGF MGF MGF Part Name & Description CHIP CHIP CHIP CHIP CHIP CHIP 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 10K 10K 180 100 10K 10K Remarks
PIN HEADERS
Ref. No. P6701 Part No. LSJA0527 Part Name & Description CONNECTOR CABLE W/PLUG Remarks
SWITCHES
Ref. No. SW6701 SW6702 SW6703 SW6704 SW6705 SW6706 Part No. EVQ11G05R EVQ11G05R EVQ11G05R EVQ11G05R EVQ11G05R EVQ11G05R Part Name & Description SWITCH SWITCH SWITCH SWITCH SWITCH SWITCH PUSH PUSH PUSH PUSH PUSH PUSH Remarks
13.4.5.
Ref. No. C4551
NETWORK C.B.A.
CAPACITORS
Part No. Part Name & Description ELECTROLYTIC 63V 3.3UF Remarks
F2J1J3R3A003
PIN HEADERS
Ref. No. P4551 P4552 P4553 Part No. K1KA02A00229 K1KA02A00188 K1KA02A00008 Part Name & Description CONNECTOR 2P CONNECTOR 2P CONNECTOR 2P Remarks
13.4.6.
Ref. No. P2912
COVER SWITCH C.B.A.

PIN HEADERS
Part No. Part Name & Description CONNECTOR CABLE W/PLUG Remarks
LSJA0476
SWITCHES
Ref. No. SW2911 Part No. K0L1BA000070 Part Name & Description SWITCH PUSH Remarks
13.4.7.
Ref. No. R2811
THERMISTOR 1 C.B.A.
RESISTORS
Part No. Part Name & Description THERMISTOR Remarks MKE
D4CA35030002
PIN HEADERS
Ref. No. P2811 Part No. K1KA02A00229 Part Name & Description CONNECTOR 2P Remarks MKE
13.4.8.
Ref. No. R2821
THERMISTOR 2 C.B.A.
RESISTORS
Part No. Part Name & Description THERMISTOR Remarks MKE
D4CE31330001
PIN HEADERS
Ref. No. P2821 Part No. K1KA02A00100 Part Name & Description CONNECTOR 2P Remarks MKE
MISCELLANEOUS
Ref. No. 762 Part No. LSJA0533 Part Name & Description CONNECTOR CABLE W/PLUG Remarks MKE
95
PT-43LC14 / PT-50LC14 / PT-60LC14
PT-43LC14 / PT-50LC14 / PT-60LC14
10.2. INTERCONNECTION SCHEMATIC DIAGRAM
14 SCHEMATIC DIAGRAMS FOR PRINTING WITH LETTER SIZE
INTERCONNECTION SCHEMATIC DIAGRAM

THERMAL FUSE UNIT REPLACEMENT NOTE: CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE SAME TYPE NUMBER LSJA0464-FE (115 ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQUES D INCENDIE N UTILISERQUE DES FUSIBLE DE MME TYPE NUMRO LSJA0464-FE (115 ) ).
NOTE: For placing a purchase order of t be sure to use the part number li NOTE: Do not use the part number on th FOR SCHEMATIC DIAGRAM AND CIRCUIT BOARD LAY REFER TO BEGINNING OF SCHEMATIC SECTION.
TV/TUNER UNIT MAIN C.B.A. P3401 P1007 (14 Pins) POWER C.B.A. P1007 P804 P1006 (3 Pins)
73
AC CORD FAN 4
HDMI IN P805 P1001 HDMI AUDIO IN L-CH HDMI AUDIO IN R-CH BALLAST C.B.A. P1302 P1303 P1305 P1305 (4 Pins) RGB AUDIO IN 1 P1306 OPERATION C.B.A. P6701 P6701 (9 Pins) P6305 F001 115 THERMAL (239 F) FUSE UNIT FAN 2 P2903 (3 Pins) P1301 (5 Pins) P1301 LAMP UNIT P2902 (3 Pins) FAN 1 PROJECTION UNIT FAN CASE UNIT P1009 P1010 P1011 P1009 (3 Pins)
96
RGB IN 1 P6002 FRONT JACK C.B.A. S-VIDEO IN 3 VIDEO IN 3 AUDIO IN 3 L-CH AUDIO IN 3 R-CH P3902 RGB IN 2 P3903 RGB AUDIO IN 2 P3902 (12 Pins) P3903 (3 Pins) P6301 (8 Pins) P6301 USED FOR ADJUSTMENT AT FACTORY ONLY P7003 UHF/VHF MAIN TUNER UHF/VHF IN P7003 (7 Pins) P6003 P3403 P3404 P3901 P3901 (10 Pins) P5501 P6001 (6 Pins) P6001 USED FOR ADJUSTMENT AT FACTORY ONLY P6007 (4 Pins) P6007 USED FOR ADJUSTMENT AT FACTORY ONLY P6008 (5 Pins) P6008 USED FOR ADJUSTMENT AT FACTORY ONLY P3402 P5302 TUNER C.B.A. PIN (14 Pins) REAR JACK C B A (14 Pins)
P1302 (2 Pins)
LCD DRIVE C.B.A. P2501 P2001 (36 Pins)
LCD / PRISM UNIT LCD PANEL (RED) FAN 3 P2904 (3 Pins) LCD PANEL (GREEN)
14 (20 Pins)
P2002 (36 Pins) P2502 LCD PANEL (BLUE)

97 (8 Pins)
COVER SWITCH C.B.A. P2912 (2 Pins) P2912
P2901
P2003 (36 Pins) THERMISTOR 1 C.B.A. P2303 (2 Pins) P2302 (8 Pins) P2302 USED FOR ADJUSTMENT OF LCD DRIVE C.B.A. P2304
762 (2 Pins)
P2811
RE HAZARD, 0464-FE (115 RISQUES
).
NOTE: For placing a purchase order of the parts, be sure to use the part number listed in the parts list. NOTE: Do not use the part number on this diagram. FOR SCHEMATIC DIAGRAM AND CIRCUIT BOARD LAYOUT NOTES, REFER TO BEGINNING OF SCHEMATIC SECTION.
NOTE: FOR SCHEMATIC DIAGRAM AND CIRCUIT BOARD LAYOUT NOTES, NOTE: REFER TO BEGINNING OF SCHEMATIC SECTION.
NOTE: SUPPLIED AS A OPTIONAL ACCESSORY. PARTS MARKED "PT" ARE NOT USED.
THE LAMP UNIT IS NOT SUPPLIED AS A REPLACEMENT PART. WHEN REPLACING, REPLACE THE LAMP UNIT WHICH IS
TV/TUNER UNIT
73
P804 P1006
AC CORD FAN 4 (3 Pins)
P1009 P1010 P1011
P1009 (3 Pins)
PROJECTION UNIT FAN CASE UNIT FAN 1 LAMP UNIT P2902 (3 Pins)
97
ns) ns) ns) ED FOR MENT OF E C.B.A.
F001 115 THERMAL (239 F) FUSE UNIT
FAN 2 P2903 (3 Pins)
LCD / PRISM UNIT LCD PANEL (RED) P2904 (3 Pins) LCD PANEL (GREEN) COVER SWITCH C.B.A. P2502 LCD PANEL (BLUE) P2912 (2 Pins) P2912 FAN 3
THERMISTOR 1 C.B.A.
PT-43LC14 / PT-50LC14 / PT-60LC14
P2303 (2 Pins)
P2811

762 (2 Pins)
P2821
AUDIO AMP C B A
PT-43LC14 / PT-50LC14 / PT-60LC14
10.3. FRONT JACK SCHEMATIC DIAGRAM
FRONT JACK SCHEMATIC DIAGRAM

VIDEO SIGNAL(MAIN/SUB) SUB VIDEO SIGNAL AUDIO SIGNAL
NOTE: For placing a purchase order of t be sure to use the part number li Do not use the part number on th
R3914
100 JK4801 K1U412A00006 0 1 2 3 4 5 6 D3911 PT 0 D3912 PT 7 8 9 VIDEO IN3
C3561 R3911
TO REAR JACK C.B.A. P3502 L3_CPS_NOSIG_L L3_S_IN_L LINE3_Y GND LINE3_C GND LINE3_V GND LINE3_L_AUDIO GND LINE3_R_AUDIO GND
75
PT
L3901
P3902 1 2 3 4 5 6 7 8 9 10 11 12 L3902 0
Y C
S-VIDEO IN3
L3903
R3912
75
D4593
PT D4592
R3913
PT R4595
75
L4801
10 11 12 13 D4801 PT D4802 PT D3913 PT AUDIO IN3(R) L3904 0 AUDIO IN3(L)
L4802
R3901
TO MAIN C.B.A. P5501 RGB2_R GND RGB2_G GND RGB2_B GND RGB2_H GND RGB2_V GND
PT 75[F]
L3905
R3902
TO REAR JACK C.B.A. P3504 RGB2_L_AUDIO RGB2_R_AUDIO GND
P3903 1 2 3
L4803 L4804
R3903
D4803
D4804
75[F]
0 0
7 6 1 2 3 4 5
75[F]
98
JK4802 K2HC103A0017
RGB AUDIO IN2
PT
PT
P3901 1 2 3 4 5 6 7 8 9 10
L3906
L3907
L3908
PT-43LC14 / PT-50LC14 / PT-60LC14
PT JK4590 PT K2HC103A0017 7 6 1 2 3 4 5
D4593
PT D4592
PT R4595
HEADPHONE
) L3904 0
R3901
PT 75[F]
R3903
IO IN2
RGB2_R GND RGB2_G GND RGB2_B GND RGB2_H GND RGB2_V GND
R3902
75[F]
75[F]
R3915
R3916
L3907
R3917
99
JK3901 K1FB115A0015 L3905 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 R3918 PT R3919 PT D3901 B0BD6R200002 (6.2V) R3920 PT RED GREEN BLUE NC CSYNC(MAC2) RED RETURN GREEN RETURN BLUE RETURN NC GND GND I2C DATA HSYNC VSYNC I2C SCK TO MAIN C.B.A. P5501 P3901 1 2 3 4 5 6 7 8 9 10 0 L3906 0 RGB IN2
PT-43LC14 / PT-50LC14 / PT-60LC14
L3908
PT-43LC14 / PT-50LC14 / PT-60LC14
PT-43LC14 / PT-50LC14 / PT-60LC14
10.4. NETWORK / THERMISTOR 1 / THERMISTOR 2 / OPERATION / COVER SWITCH SCHEMATIC DIAGRAMS
(FOR L-CH SPEAKER)

J4551 WA5 C4551 3R3/63V R4551 PT P4553 2 1 TO AUDIO AMP C.B.A. P4503 AUDIO SIGNAL
OPERATION SCHEMATIC DIAGRA

R6702 R6703
TO MAIN C.B.A. P6305 GND STBY5V P_LED_G P_LED_R SCAN2 SCAN1 SCAN0 KEY_IN1 KEY_IN0 P6701 9 8 7 6 5 4 3 2 1 SW6701 EVQ11G05R CH_UP SW6702 EVQ11G05R CH_DOWN
P4503-3 P4503-4
TO L-CH SPEAKER (TWEETER)
P4551 SP_OUT_L_TW 2 AMP_GND 1 P4552
TO L-CH SPEAKER (WOOFER)
LSJB3097
(FOR R-CH SPEAKER)

AUDIO SIGNAL TO R-CH SPEAKER (TWEETER) J4551 WA5 P4551 2 1 C4551 3R3/63V R4551 PT TO AUDIO AMP C.B.A. P4553 P4503 2 SP_OUT_R P4503-1 AMP_GND P4503-2 1
SP_OUT_R_TW AMP_GND TO R-CH SPEAKER (WOOFER)
P4552
SP_OUT_R_WF 2 AMP_GND 1
LSJB3097

TO LCD DRIVE C.B.A. P2303 P2811 1 THERMO_4 2 THERMO_3
R2811 D4CA35030002
LSJB3136
COVER SWITCH SCHEMATIC DIAG

J2911 PT
P2912
TO LCD DRIVE C.B.A. P2502
10K
SP_OUT_L_WF 2 AMP_GND 1
SP_OUT_L AMP_GND
10K
100
OVER SWITCH SCHEMATIC DIAGRAMS
OPERATION SCHEMATIC DIAGRAM

R6702 R6706 R6704 180 R6705
R 1 3 G
10K
R6703
100
R6707
10K
2 D6701 B3AGA0000072 POWER LED
TO MAIN C.B.A. P6305 GND STBY5V P_LED_G P_LED_R SCAN2 SCAN1 SCAN0 KEY_IN1 KEY_IN0
P6701 9 8 7 6 5 4 3 2 1 SW6701 EVQ11G05R CH_UP
SW6703 EVQ11G05R VOL_UP
SW6706 EVQ11G05R INPUT
SW6702 EVQ11G05R CH_DOWN
SW6704 EVQ11G05R VOL_DOWN
SW6705 EVQ11G05R POWER
10K
10K
101
LSJB3128
PT-43LC14 / PT-50LC14 / PT-60LC14
COVER SWITCH SCHEMATIC DIAGRAM

J2911 PT
P2912
TO LCD DRIVE C.B.A. P2502
PT-43LC14 / PT-50LC14 / PT-60LC14
10.5. AUDIO AMP SCHEMATIC DIAGRAM

AUDIO AMP SCHEMATIC DIAGRAM
AUDIO SIGNAL
PT 0 R4540
PT 10K R4537 PT
PT R4539
R4541
PT R4538
PT 2700
C4521 PT 0.1[KB]
PT 10/16V
C4520
C4534 C4535 PT100/6.3V PT 100/6.3V
PT PT 2R7 2R7
PT 0.1[KB] C4523
R4521
R4520
R4542
Q4506 PT 2SB710ARS R4533
PT 330
IC4503 C0CAAKE00013 (+12V REG.) +12V REG. 2
MUTE_L
POWER_G
VCC
R4532
10
PT 47 C4536 PT
3 POWER ON_H 1 2 PRE_G 3 4 5 C4522 PT 22/6.3V R4516 PT 47K IC4501 C1AA00000660 (AUDIO AMP) C4533 PT C4532 PT
C4514 10/50V
C4516 10/16V
R4517 PT 47K ( TO POWER C.B.A. P1009 P1010 P1011 ) P4501 +Vs 1 GND 2 -Vs 3 C4512 0.1 C4513 0.1 C4501 1000/35V C4502 1000/35V R4501 4700 D4501 MAZ40510MF (5.1V) R4506 15K R4508 33K C4506
-Vs +Vs -Vs
R4519
R4518
PT 0
PT 1/50V[N]
GND
10
11 C4511 C4510 1/50V[N]
R4544 0 R4543 0
C4531
PT C4530
C4503 10/16V
R4502 15K
0.047[KB] R4507 R4509 15K 33K C4507 0.047[KB] 3.3V
R4503
C4508
16V[N]
C4526
PT
7P
C4527
1200
16V[N]
1K
R4505
R4546 0
RL4501 K6B2AGA00038
4R7 RX1SJ4R7P
SW_IN_L SW_OUT_L H/P_IN_L AMP_GND H/P_IN_R SW_IN_R SW_OUT_R
J4504 WA5
R4512
470
R4529 1200 R4531
R4510
R4528 1K R4530
R4513
470
470 C4509
R4545
0.068[KB] R4511
470
0.068[KB]
10K
TO FRONT JACK C.B.A. P4591
P4502 PT 7 6 5 4 3 2 1
Q4501 2SD0601AHL SWITCHING AUDIO MUTE-ON R4524 PT
R4525 0
PT
1/50V[N]
PT 1/50V[N]
+-
-+
C4519
C4518
PT 0
R4535
IC4502 PT
Q4507 PT 2SD601A
102
PT-43LC14 / PT-50LC14 / PT-60LC14

PT 10K R4537 PT
PT 0 R4540
PT R4539
R4541
PT R4538
PT 2700
C4521 PT 0.1[KB]
PT 10/16V
C4520
C4534 C4535 PT100/6.3V
PT PT 2R7 2R7
PT 0.1[KB] C4523
R4521
R4520
J4502 PT Q4506 PT 2SB710ARS R4533
R4542
R4536 PT22
PT 330
MUTE_L
POWER_G
VCC
R4532
10
PT 47K C4536 PT
R4535
PT 10K
IC4502 PT
Q4507 PT 2SD601A
PT 10/16V R4534 PT1K
PT 100/6.3V
POWER ON_H 1 2
PRE_G 3 4 5 C4522 PT 22/6.3V R4516 PT 47K
Q4508 PT 2SD601A
R4517 PT 47K
C4529
R4519
R4518
PT 0
PT 1/50V[N]
GND
PT 1/50V[N]
+7 8 9 10
-+ 11 C4511 C4510 1/50V[N]
C4519
C4518
PT 0
C4531
PT C4530
R4508 33K C4506
0.047[KB] 7 R4509 33K C4507 0.047[KB] 3.3V
PT
0.068[KB] R4511
R4510
R4512
470
R4513
470
470 C4509
/16V[N]
C4526
C4527
/16V[N]
470
0.068[KB]
C4508
103
1/50V[N]
P4505 6 5 4 3 2 1 J4501 WA7.5
TO REAR JACK C.B.A. P3603
C4533 PT
C4532 PT
5V AMP_MUTE_L AUDIO_G AMP_R_AUDIO AUDIO_G AMP_L_AUDIO
R4544 0 R4543 0
PT-43LC14 / PT-50LC14 / PT-60LC14
PT-43LC14 / PT-50LC14 / PT-60LC14
PT-43LC14 / PT-50LC14 / PT-60LC14
10.6. TUNER SCHEMATIC DIAGRAM

TUNER SCHEMATIC DIAGRAM
Z7001 U7001 ENGF6302GF LSJA0468 U7101 ENG36A08GF
VIDEO SIGNAL(MAIN/SUB) AUDIO SIG
NC(CONTROL)
NC(CONTROL)
MAIN_TUNER
NC(AUDIO IN) NC(VIDEO IN) NC AGC_CONT AUDIO OUT VIDEO OUT NC(CH SW) AGC_VR NC(IF OUT) NC(XTAL) AGC SIF_OUT NC(BT) AFT SCK SDA BTL NC BC
SUB_T
NC(VIDEO IN) NC(IF OUT) NC(XTAL) AGC NC(BT) SCK SDA NC AFT
NC(AUDIO IN)
NC(CH SW) AGC_VR
BC
10
11 12 R7005 0
13
14
15
16
17
10
11 12 R7106 0
PT C7005
ESD GND
PT
P7001 1
C7003
R7009 PT
C7012
C7103
PT C7004
PT C7104
PT C7105
C7001 2200P[KB] C7002 1000/6.3V

L7001 10U
C7101 2200P[KB] C7102 1000/6.3V
PT
R7008 22
C7009 10/16V
C7010
C7011
Q7002 PT
L7101
PT C7007 PT C7008
100 100 100
10U
PT C7107 PT C7108
R7007 PT
100
PT
PT
R7006
R7001 R7004 R7002 R7003
R7101
R7102
TP7001 WA10 TO REAL JACK C.B.A. P3501 M_TNR_VIDEO GND S_TNR_VIDEO GND M_TNR_L_AUDIO GND M_TNR_R_AUDIO GND
TP7101 WA10
Q7001 PT
P7002 1 2 3 4 5 6 7 8 R7514 R7517 D7501 PT D7502 PT 50KB 33K SEPARATION
R7512 PT
R7515 R7516 PT 50KB PT
B/B IN
TP7501 WA10
R7501 C7501 100 100K C7509 100/6.3V PT PT 180K PT 2200 R7503 PT R7505 0.01 2R2/50V 2R2/50V 0.22[KB] 0.33/50V 10/16V 0.1[KB] 100 100K
L7501 100U
PT
PT
0.01
R7508 R7509
C7512
C7517
R7510 R7511
C7515
C7520
C7510
C7511
R7506 0
C7502
TP7502 WA10
32
31
R7504
30
29
R7507 C7506
28
27
26
25
24
23
22
21
C7513
20
19
18
17
C7519
R7513 3300
R7103
PT
100
100
C7109
C7006
0.01[KB]
PT
C7106
PT
104
JA0468 U7101 ENG36A08GF VIDEO SIGNAL(MAIN/SUB) AUDIO SIGNAL
SUB_TUNER
NC(CONTROL) NC(AUDIO IN) NC(VIDEO IN) NC AGC_CONT AUDIO OUT VIDEO OUT NC(CH SW) AGC_VR NC(IF OUT) NC(XTAL) AGC SIF_OUT NC(BT) SCK SDA AFT BTL NC BC
10
11 12 R7106 0
13
14
15
16
17
C7103
PT C7104
PT C7105
C7112
PT
PT C7110
C7109
C7111
L7101
10U
PT C7107 PT C7108
100
PT
PT
R7101
100
R7102
R7103
100
Q7101 PT
C7106
PT
C7102 1000/6.3V
PT
R7104 22
PT
R7105 PT
PT
C7101 2200P[KB]
PT
0.22[KB]
0.33/50V
10/16V
PT
R7513 3300
C7512
C7517
C7515
C7520
C7513
C7519
0.1[KB]
0.01
105
P7003 1 2 3 4 5 6 7
TO MAIN C.B.A. P6004 S_AFC M_AFC I2C_SCK_5V I2C_DATA_5V 5V 30V GND
R7514 R7517 50KB 33K
SEPARATION
R7512 PT
R7515 R7516 PT 50KB PT
B/B IN
L7501 100U
PT-43LC14 / PT-50LC14 / PT-60LC14

Panasonic PT-50LC14

Uploaded by

Copyright:

Available Formats

Panasonic PT-50LC14

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Panasonic PT-50LC14

Uploaded by

Copyright:

Available Formats

ORDER NO.

Multi Media Display

PT-43LC14 PT-50LC14 PT-60LC14

PT-43LC14 / PT-50LC14 / PT-60LC14

10.1. SCHEMATIC DIAGRAM AND CIRCUIT BOARD LAYOUT

13.3. OPTIONAL ACCESSORY REPLACEMENT PARTS LIST

PT-43LC14 / PT-50LC14 / PT-60LC14

LEAKAGE CURRENT COLD CHECK

LEAKAGE CURRENT HOT CHECK

PT-43LC14 / PT-50LC14 / PT-60LC14

2 PREVENTION OF ELECTROSTATIC DISCHARGE (ESD) TO ELECTROSTATICALLY SENSITIVE (ES) DEVICES

PT-43LC14 / PT-50LC14 / PT-60LC14

3 ABOUT LEAD FREE SOLDER (PbF)

PT-43LC14 / PT-50LC14 / PT-60LC14

(Note 2) Error No.

(Note 3) LAMP OFF

PT-43LC14 / PT-50LC14 / PT-60LC14

MAIN PARTS LOCATION

Lamp Cover Cover Switch C.B.A.

TEMP LED LAMP LED Network C.B.A.

Optical Cover Front Cover Unit Operation C.B.A. POWER LED

Front Jack C.B.A. Main C.B.A.

Ballast C.B.A. Tuner C.B.A.

Air Filter Air Filter

Fan 2 LCD Drive C.B.A.

Audio Amp C.B.A.

Rear Cover Power C.B.A. Rear Jack C.B.A. TV/Tuner Unit

PT-43LC14 / PT-50LC14 / PT-60LC14

Service Mode Map

(for more than 5 seconds in power off condition) Power ON

OPERATION RENT LAMP: DISPLAY : COUNT : : 4B 7E 3D

< Service Mode (1/3) >

< Service Mode (2/3) >

< Service Mode (3/3) >

PT-43LC14 / PT-50LC14 / PT-60LC14

OPERATION RENT LAMP: DISPLAY : COUNT : : 4B 7E 3D

OPERATION RENT LAMP: DISPLAY : COUNT : : B0 3A 59

CUR OSD LON BKSV

<Service Mode (1/3)> Fig. 3

Service Mode Map

(for more than 5 seconds in power off condition) Power ON

OPERATION RENT LAMP: DISPLAY : COUNT : : 4B 7E 3D

< Service Mode (1/3) >

Daily average use X (hours)

Approx. age (days)

CURRENT LAMP (hours)

< Service Mode (2/3) >

< Service Mode (3/3) >

PT-43LC14 / PT-50LC14 / PT-60LC14

Lamp Replacement Procedure:

Lamp Cover Screw

PT-43LC14 / PT-50LC14 / PT-60LC14

Air Filter Air Filter

Fresnel Lens surface (inside)

PT-43LC14 / PT-50LC14 / PT-60LC14

TO DISTINGUISH THE PROJECTION LENS UNIT OR THE PROJECTION UNIT

RESET USERS MEMORY FUNCTIONS

CLOGGED AIR FILTER DETECTION

PT-43LC14 / PT-50LC14 / PT-60LC14