Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 2K views

    HDB-Supervision Guide For Electrical Engineering Works

    Uploaded by

    Zhu Qi Wang
    This document provides guidance for supervising electrical engineering works. It outlines requirements for quality control, specific installation requirements, document submissions, good practices, and common defects. Key points include no-drill zones for electrical accessories, lightning protection system details, TV system security measures, first story trunking routes, inspection of concealed conduits, and electrical finishes meeting CONQUAS standards.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd

    HDB-Supervision Guide For Electrical Engineering Works

    Uploaded by

    Zhu Qi Wang
    2K views24 pages
    This document provides guidance for supervising electrical engineering works. It outlines requirements for quality control, specific installation requirements, document submissions, good practices, and common defects. Key points include no-drill zones for electrical accessories, lightning protection system details, TV system security measures, first story trunking routes, inspection of concealed conduits, and electrical finishes meeting CONQUAS standards.

    Original Title

    HDB-Supervision Guide for Electrical Engineering Works

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides guidance for supervising electrical engineering works. It outlines requirements for quality control, specific installation requirements, document submissions, good practices, and common defects. Key points include no-drill zones for electrical accessories, lightning protection system details, TV system security measures, first story trunking routes, inspection of concealed conduits, and electrical finishes meeting CONQUAS standards.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    2K views24 pages

    HDB-Supervision Guide For Electrical Engineering Works

    Uploaded by

    Zhu Qi Wang
    This document provides guidance for supervising electrical engineering works. It outlines requirements for quality control, specific installation requirements, document submissions, good practices, and common defects. Key points include no-drill zones for electrical accessories, lightning protection system details, TV system security measures, first story trunking routes, inspection of concealed conduits, and electrical finishes meeting CONQUAS standards.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 24

    Supervision Guide for Electrical Engineering Works

    Introduction To develop quality management system and checklists / forms for supervising Electrical Engineering Works

    Quality Control
    Material Timber mock up Trades Demonstration Sample units In-process checking Delivery and storage Testing & commissioning Handover inspection

    Specific Requirement
    No Drill Zone
    150mm bandwidth to the left, right, above and below w.r.t. all conceal electrical accessory and also below ceiling

    Specific Requirement
    Lightning Protection System

    HDB use aluminium lightning tape on the roof top and run the aluminium down conductor on surface of external wall/column.

    The aluminum down conductor is connect to copper tape using bi-metallic aluminum/copper connector at a height of 2.5m. The copper tape shall be properly concealed or embedded to prevent it from being removed

    Specific Requirement
    TV System

    All distribution amplifiers are to be properly secured with locking device and engrossed with Serial number. All Tee units in the Telecom Riser and distribution amplifiers are to be spray painted

    Submission
    Services coordination drawings

    First Storey trunking route and penetration

    Good Practices / Common Defects

    Good Practices/Common Defects


    Electrical Installation

    Conceal conduits should be gradually bent and has no more than 2 nos. of 90 degree bend between two points and the crossing of conduits should be kept to a minimum so that the covering of the conduit should be sufficient

    Good Practices/Common Defects


    Electrical Installation

    Location of conceal conduit w.r.t. the precast component must be checked Proper conduit accessories are to be used

    Good Practices/Common Defects


    Electrical Installation

    Conceal conduit running outside the no drill zone

    Good Practices/Common Defects


    Electrical Installation

    For those socket outlets to be installed at the brick wall

    The Consultant can consider casting the socket outlets separately to ensure that the socket outlets are in level position and also reduce the need to hack the brick wall later for the installation of conduits.

    Good Practices/Common Defects


    Electrical Installation

    No cable should be exposed without the protection of a conduit, trunking or some other form of protection

    Good Practices/Common Defects


    Electrical Installation

    The Consultant should inspect and paid attention on the running of the conceal conduit in block walls.

    X X

    In this case, metal conduit should be used

    Good Practices/Common Defects


    Electrical Installation

    In instances where two residential units share one common riser duct, PowerGrid meter boxes should be placed logically for identification

    Good Practices/Common Defects


    Electrical Installation

    The Consultant should check to ensure that the main door does not hit the CCU when fully opened.

    Good Practices/Common Defects


    Earth System

    The Consultant should ensure all necessary information of the earth system engraved on a durable identification tag to be fixed onto the inside top of the earth pit

    Good Practices/Common Defects


    ELV Installation

    Proper separations between Switched socket outlet box and TV outlet box

    Good Practices/Common Defects


    Lightning Protection System

    Location of the aluminium air terminal should be check and relocated appropriately with consideration of the ladder or railing installed at the roof

    Good Practices/Common Defects


    Lightning Protection System Re-entrant loop should be avoided

    CONQUAS

    Finishes must be even, level, align & consistent No stain marks and visible damages / defects

    Thank You

    Timber Mock Up

    The Consultant should inspect and verify the position of all electrical provision, esp at toilet and balcony - heater point at toilet - power point for the washing machine

    In Process Checking

    The Consultant should verify that the Electrical Sub-contractor is - BCA registered contractor of at least L2 grade - Registered with Qualified Electrical Contractors Registry maintained by IES/ACES

    You might also like