Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 44 views

    Praktikum V DSP Dengan Menggunakan ARM: Hariyanto (1310125026) Selvira Rahadiningrum Ramelan (1310125027)

    Uploaded by

    Primaridha Saputra
    This document describes three experiments in digital signal processing using an ARM processor: 1) Generation of a sinusoidal wave. 2) Generation of a square wave. 3) Generation of a triangular wave. C code is provided to configure the ADC, DAC, and timers necessary to generate and output the signals. Diagrams of the expected signal shapes are included.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as DOC, PDF, TXT or read online from Scribd

    Praktikum V DSP Dengan Menggunakan ARM: Hariyanto (1310125026) Selvira Rahadiningrum Ramelan (1310125027)

    Uploaded by

    Primaridha Saputra
    44 views6 pages
    This document describes three experiments in digital signal processing using an ARM processor: 1) Generation of a sinusoidal wave. 2) Generation of a square wave. 3) Generation of a triangular wave. C code is provided to configure the ADC, DAC, and timers necessary to generate and output the signals. Diagrams of the expected signal shapes are included.

    Original Title

    Percobaan 5

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    DOC, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document describes three experiments in digital signal processing using an ARM processor: 1) Generation of a sinusoidal wave. 2) Generation of a square wave. 3) Generation of a triangular wave. C code is provided to configure the ADC, DAC, and timers necessary to generate and output the signals. Diagrams of the expected signal shapes are included.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as DOC, PDF, TXT or read online from Scribd
    Download as doc, pdf, or txt
    44 views6 pages

    Praktikum V DSP Dengan Menggunakan ARM: Hariyanto (1310125026) Selvira Rahadiningrum Ramelan (1310125027)

    Uploaded by

    Primaridha Saputra
    This document describes three experiments in digital signal processing using an ARM processor: 1) Generation of a sinusoidal wave. 2) Generation of a square wave. 3) Generation of a triangular wave. C code is provided to configure the ADC, DAC, and timers necessary to generate and output the signals. Diagrams of the expected signal shapes are included.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as DOC, PDF, TXT or read online from Scribd
    Download as doc, pdf, or txt
    of 6

    Hariyanto (1310125026) Selvira Rahadiningrum Ramelan (1310125027)

    Praktikum V DSP dengan menggunakan ARM


    Percobaan 1 (Gelombang Sinus)

    List Program :
    #include "stm32f4_discovery.h" #include <stdio.h> #include "arm_math.h" #define DEG2RAD

    0.0174532925199432

    //GPIO_InitTypeDef GPIO_InitStructure; float ts, T,delt,t; int n,ns,nh,ni; float fin,vm,ofset; float vt[2000]; /* Private function prototypes -----------------------------------------------*/ void TIM_Config(void); void ADC3_CH12_DMA_Config(void); void DAC_Config(void); int main(void) { /* ADC3 configuration *******************************************************/ /* - Enable peripheral clocks */ /* - DMA2_Stream0 channel2 configuration */ /* - Configure ADC Channel12 pin as analog input */ /* - Configure ADC3 Channel12 */ ADC3_CH12_DMA_Config(); /* Start ADC3 Software Conversion */ ADC_SoftwareStartConv(ADC3); /* TIM Configuration */ TIM_Config(); /* DAC Config */ DAC_Config(); /* GPIOD Periph clock enable */ // RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOD, ENABLE); // /* Configure PD12, PD13, PD14 and PD15 in output pushpull mode */ // GPIO_InitStructure.GPIO_Pin = GPIO_Pin_12 | GPIO_Pin_13| GPIO_Pin_14| GPIO_Pin_15; // GPIO_InitStructure.GPIO_Mode = GPIO_Mode_OUT; // GPIO_InitStructure.GPIO_OType = GPIO_OType_PP; // GPIO_InitStructure.GPIO_Speed = GPIO_Speed_100MHz; // GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL; // GPIO_Init(GPIOD, &GPIO_InitStructure); if (SysTick_Config(SystemCoreClock / 1000)) { /* Capture error */ while (1); } ts = 0.001; fin = 10; vm =4000; ofset = 2000; T = 1/fin; ns = T / ts; nh =1; for (ni=0;ni<ns;ni++) {

    DIGITAL SIGNAL PROCESSING (DSP)

    Hariyanto (1310125026) Selvira Rahadiningrum Ramelan (1310125027)


    vt[ni]=2000; } for(n=1;n<=nh;n=n+2) { for(ni=0,t=0;ni<=ns;ni++) { t=t+ts;

    vt[ni]=vt[ni] + (4 * vm / n / PI) * arm_sin_f32(2 * n * PI * t / T);


    } } ni=0; while (1) {

    /* DAC_SetChannel1Data(DAC_Align_12b_R, ADC3ConvertedValue); */ /* convert the ADC value (from 0 to 0xFFF) to a voltage value (from 0V to 3.3V)*/ // // } } // ADC3ConvertedVoltage = ADC3ConvertedValue *3300/0xFFF; voltage = ADC3ConvertedValue *3.30/0xFFF; count++;

    void assert_failed(uint8_t* file, uint32_t line) { /* User can add his own implementation to report the file name and line number, ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */ /* Infinite loop */ while (1) { } }

    Bentuk sinyal :

    DIGITAL SIGNAL PROCESSING (DSP)

    Hariyanto (1310125026) Selvira Rahadiningrum Ramelan (1310125027) Percobaan 2 (Gelombang Square Wave) List Program :
    #include "stm32f4_discovery.h" #include <stdio.h> #include "arm_math.h" #define DEG2RAD

    0.0174532925199432

    //GPIO_InitTypeDef GPIO_InitStructure; float ts, T,delt,t; int n,ns,nh,ni; float fin,vm,ofset; float vt[2000]; /* Private function prototypes -----------------------------------------------*/ void TIM_Config(void); void ADC3_CH12_DMA_Config(void); void DAC_Config(void); int main(void) { /* ADC3 configuration *******************************************************/ /* - Enable peripheral clocks */ /* - DMA2_Stream0 channel2 configuration */ /* - Configure ADC Channel12 pin as analog input */ /* - Configure ADC3 Channel12 */ ADC3_CH12_DMA_Config(); /* Start ADC3 Software Conversion */ ADC_SoftwareStartConv(ADC3); /* TIM Configuration */ TIM_Config(); /* DAC Config */ DAC_Config(); /* GPIOD Periph clock enable */ // RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOD, ENABLE); // /* Configure PD12, PD13, PD14 and PD15 in output pushpull mode */ // GPIO_InitStructure.GPIO_Pin = GPIO_Pin_12 | GPIO_Pin_13| GPIO_Pin_14| GPIO_Pin_15; // GPIO_InitStructure.GPIO_Mode = GPIO_Mode_OUT; // GPIO_InitStructure.GPIO_OType = GPIO_OType_PP; // GPIO_InitStructure.GPIO_Speed = GPIO_Speed_100MHz; // GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL; // GPIO_Init(GPIOD, &GPIO_InitStructure); if (SysTick_Config(SystemCoreClock / 1000)) { /* Capture error */ while (1); } ts = 0.001; fin = 10; vm =4000; ofset = 2000; T = 1/fin; ns = T / ts; nh =1000; for (ni=0;ni<ns;ni++) { vt[ni]=2000; } for(n=1;n<=nh;n=n+2) { for(ni=0,t=0;ni<=ns;ni++) { t=t+ts;

    DIGITAL SIGNAL PROCESSING (DSP)

    Hariyanto (1310125026) Selvira Rahadiningrum Ramelan (1310125027)


    vt[ni]=vt[ni] + (4 * vm / n / PI) * arm_sin_f32(2 * n * PI * t / T); } } ni=0; while (1) {

    /* DAC_SetChannel1Data(DAC_Align_12b_R, ADC3ConvertedValue); */ /* convert the ADC value (from 0 to 0xFFF) to a voltage value (from 0V to 3.3V)*/ // // } } // ADC3ConvertedVoltage = ADC3ConvertedValue *3300/0xFFF; voltage = ADC3ConvertedValue *3.30/0xFFF; count++;

    void assert_failed(uint8_t* file, uint32_t line) { /* User can add his own implementation to report the file name and line number, ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */ /* Infinite loop */ while (1) { } }

    Bentuk sinyal :

    DIGITAL SIGNAL PROCESSING (DSP)

    Hariyanto (1310125026) Selvira Rahadiningrum Ramelan (1310125027) Percobaan 3 (sinyal segitiga)

    List Program :
    #include "stm32f4_discovery.h" #include <stdio.h> #include "arm_math.h" #define DEG2RAD

    0.0174532925199432

    //GPIO_InitTypeDef GPIO_InitStructure; float ts, T,delt,t; int n,ns,nh,ni; float fin,vm,ofset; float vt[2000]; /* Private function prototypes -----------------------------------------------*/ void TIM_Config(void); void ADC3_CH12_DMA_Config(void); void DAC_Config(void); int main(void) { /* ADC3 configuration *******************************************************/ /* - Enable peripheral clocks */ /* - DMA2_Stream0 channel2 configuration */ /* - Configure ADC Channel12 pin as analog input */ /* - Configure ADC3 Channel12 */ ADC3_CH12_DMA_Config(); /* Start ADC3 Software Conversion */ ADC_SoftwareStartConv(ADC3); /* TIM Configuration */ TIM_Config(); /* DAC Config */ DAC_Config(); /* GPIOD Periph clock enable */ // RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOD, ENABLE); // /* Configure PD12, PD13, PD14 and PD15 in output pushpull mode */ // GPIO_InitStructure.GPIO_Pin = GPIO_Pin_12 | GPIO_Pin_13| GPIO_Pin_14| GPIO_Pin_15; // GPIO_InitStructure.GPIO_Mode = GPIO_Mode_OUT; // GPIO_InitStructure.GPIO_OType = GPIO_OType_PP; // GPIO_InitStructure.GPIO_Speed = GPIO_Speed_100MHz; // GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL; // GPIO_Init(GPIOD, &GPIO_InitStructure); if (SysTick_Config(SystemCoreClock / 1000)) { /* Capture error */ while (1); } ts = 0.001; fin = 10; vm =4000; ofset = 2000; T = 1/fin; ns = T / ts; nh =1000; for (ni=0;ni<ns;ni++) { vt[ni]=2000; } for(n=1;n<=nh;n=n+2) { for(ni=0,t=0;ni<=ns;ni++)

    DIGITAL SIGNAL PROCESSING (DSP)

    Hariyanto (1310125026) Selvira Rahadiningrum Ramelan (1310125027)


    { t=t+ts; vt[ni]=vt[ni] + (8 * vm / (n*n)/ (PI*PI)) * arm_sin_f32( n * PI / 2) * arm_sin_f32( 2 * n * PI * t / T); } } ni=0; while (1) {

    /* DAC_SetChannel1Data(DAC_Align_12b_R, ADC3ConvertedValue); */ /* convert the ADC value (from 0 to 0xFFF) to a voltage value (from 0V to 3.3V)*/ // // } } // ADC3ConvertedVoltage = ADC3ConvertedValue *3300/0xFFF; voltage = ADC3ConvertedValue *3.30/0xFFF; count++;

    void assert_failed(uint8_t* file, uint32_t line) { /* User can add his own implementation to report the file name and line number, ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */ /* Infinite loop */ while (1) { } }

    Bentuk sinyal :

    DIGITAL SIGNAL PROCESSING (DSP)

    You might also like