Aws D15.2

AWS D15.
2:2003 An American National Standard
Recommended Practices for the Welding of Rails and Related Rail Components for Use by Rail Vehicles
Copyright American Welding Society Provided by IHS under license with AWS No reproduction or networking permitted without license from IHS
--`,,``,``,`,``,```,```,,````,`-`-`,,`,,`,`,,`---
Licensee=ConocoPhillips WAN/5919206100 Not for Resale, 03/31/2005 06:06:31 MST
Key Words Arc welding processes, crossings,

wheel burns, flash welding, frogs, oxyfuel welding, procedure qualification, railroad safety, railroad welding, rails, switch points, thermite welding, track, welder qualification
AWS D15.2:2003 An American National Standard Approved by American National Standards Institute October 7, 2003
Supersedes ANSI/AWS D15.2-94
Prepared by AWS D15 Committee on Railroad Welding Under the Direction of AWS Technical Activities Committee Approved by AWS Board of Directors
Abstract
--`,,``,``,`,``,```,```,,````,`-`-`,,`,,`,`,,`---
This document recommends minimum standards for the maintenance welding of rails and related rail components used by rail vehicles. Repair procedures for rails and austenitic manganese steel components are covered. Thermite welding and electric flash welding guidelines are discussed. Procedure qualification, welder qualification, and general welding safety procedures are addressed.
550 N.W. LeJeune Road, Miami, Florida 33126

Copyright American Welding Society Provided by IHS under license with AWS No reproduction or networking permitted without license from IHS Licensee=ConocoPhillips WAN/5919206100 Not for Resale, 03/31/2005 06:06:31 MST
Statement on Use of AWS American National Standards

All standards (codes, specifications, recommended practices, methods, classifications, and guides) of the American Welding Society (AWS) are voluntary consensus standards that have been developed in accordance with the rules of the American National Standards Institute (ANSI). When AWS standards are either incorporated in, or made part of, documents that are included in federal or state laws and regulations, or the regulations of other governmental bodies, their provisions carry the full legal authority of the statute. In such cases, any changes in those AWS standards must be approved by the governmental body having statutory jurisdiction before they can become a part of those laws and regulations. In all cases, these standards carry the full legal authority of the contract or other document that invokes the AWS standards. Where this contractual relationship exists, changes in or deviations from requirements of an AWS standard must be by agreement between the contracting parties. International Standard Book Number: 0-87171-717-4 American Welding Society, 550 N.W. LeJeune Road, Miami, FL 33126 2004 by American Welding Society. All rights reserved Printed in the United States of America AWS American National Standards are developed through a consensus standards development process that brings together volunteers representing varied viewpoints and interests to achieve consensus. While AWS administers the process and establishes rules to promote fairness in the development of consensus, it does not independently test, evaluate, or verify the accuracy of any information or the soundness of any judgments contained in its standards. AWS disclaims liability for any injury to persons or to property, or other damages of any nature whatsoever, whether special, indirect, consequential or compensatory, directly or indirectly resulting from the publication, use of, or reliance on this standard. AWS also makes no guaranty or warranty as to the accuracy or completeness of any information published herein. In issuing and making this standard available, AWS is not undertaking to render professional or other services for or on behalf of any person or entity. Nor is AWS undertaking to perform any duty owed by any person or entity to someone else. Anyone using these documents should rely on his or her own independent judgment or, as appropriate, seek the advice of a competent professional in determining the exercise of reasonable care in any given circumstances. This standard may be superseded by the issuance of new editions. Users should ensure that they have the latest edition. Publication of this standard does not authorize infringement of any patent. AWS disclaims liability for the infringement of any patent resulting from the use or reliance on this standard. Finally, AWS does not monitor, police, or enforce compliance with this standard, nor does it have the power to do so. On occasion, text, tables, or figures are printed incorrectly, constituting errata. Such errata, when discovered, are posted on the AWS web page (www.aws.org). Official interpretations of any of the technical requirements of this standard may be obtained by sending a request, in writing, to the Managing Director, Technical Services Division, American Welding Society, 550 N.W. LeJeune Road, Miami, FL 33126 (see Annex F). With regard to technical inquiries made concerning AWS standards, oral opinions on AWS standards may be rendered. However, such opinions represent only the personal opinions of the particular individuals giving them. These individuals do not speak on behalf of AWS, nor do these oral opinions constitute official or unofficial opinions or interpretations of AWS. In addition, oral opinions are informal and should not be used as a substitute for an official interpretation. This standard is subject to revision at any time by the AWS D15 Committee on Railroad Welding. It must be reviewed every five years, and if not revised, it must be either reapproved or withdrawn. Comments (recommendations, additions, or deletions) and any pertinent data that may be of use in improving this standard are required and should be addressed to AWS Headquarters. Such comments will receive careful consideration by the AWS D15 Committee on Railroad Welding and the author of the comments will be informed of the Committees response to the comments. Guests are invited to attend all meetings of the AWS D15 Committee on Railroad Welding to express their comments verbally. Procedures for appeal of an adverse decision concerning all such comments are provided in the Rules of Operation of the Technical Activities Committee. A copy of these Rules can be obtained from the American Welding Society, 550 N.W. LeJeune Road, Miami, FL 33126. Photocopy Rights Authorization to photocopy items for internal, personal, or educational classroom use only, or the internal, personal, or educational classroom use only of specific clients, is granted by the American Welding Society (AWS) provided that the appropriate fee is paid to the Copyright Clearance Center, 222 Rosewood Drive, Danvers, MA 01923, Tel: 978-750-8400; online: http://www.copyright.com.
--`,,``,``,`,``,```,```,,````,`-`-`,,`,,`,`,,`---
Personnel
AWS D15 Committee on Railroad Welding R. W. Dawson, Chair M. R. Untermeyer, Vice Chair E. F. Mitchell, Secretary B. C. Blackwell *J. L. Bobo C. Boulden N. S. Brown T. Bruno J. Cooley S. A. Coughlin R. T. Easterman T. Y. Gehr, Jr. *P. B. Heideman *W. Jaxa-Rozen * P. G. Kinnecom *G. A. Lycan M. J. Markase S. E. Markis *C. C. Menzemer M. T. Merlo *M. A. Miller *J. P. Moffet J. B. Pearson, Jr. *K. R. Rollins *J. Sun *J. A. Stewart L. H. Strouse J. Tolene S. W. Tribble R. A. Watson M. A. Wheeland J. B. Wheeler P. H. Williams R. A. Wolbert *D. A. Wright, Sr.
*Advisor
TTX Company Union Tank Car Company American Welding Society Standard Car Truck Company Consultant Trinity Rail Group Canadian Pacific Railway Johnstown America J. C. & Associates, Incorporated Welding Metallurgical Engineering Trinity Rail Group Esco Equipment Service Company Portland General Electric Bombardier Transportation Association of American Railroads G. A. Gage Company Taussig Materials Testing Norfolk Southern The University of Akron Select Arc, Incorporated Consolidated Rail Corporation GE Transportation Systems LTK Engineering Services Norfolk Southern Association of American Railroads Ideal Consulting Services G.E. Rail Services CNIC Railroad Track-Weld Ind., Incorporated Miner Enterprises, Incorporated Union Pacific Railroad American Rail Car Industries Victoria Mechanical Services Progress Rail Services Corporation Zephyr Welding
--`,,``,``,`,``,```,```,,````,`-`-`,,`,,`,`,,`---
iii
AWS D15 Subcommittee on Track Welding S. E. Markis, Chair T. Y. Gehr, Jr., Vice Chair E. F. Mitchell, Secretary T. L. Baxley R. L Bell D. Bjork D. N. Blowatt M. J. Boos W. C. Bragg N. Brown G. K. Clem G. Copeland *R. W. Dawson M. A. Gilstrap J. C. Handley B. F. Hansen J. R. Hornaday, Jr. C. Jackson R. S. Koblinski R. Kral P. J. Lawless M. J. Markase *D. G. McCord B. A. Meade *J. B. Pearson A. R. Pierson R. Roper S. Scharnweber *J. Sun S. W. Tribble J. G. Wallin M. A. Wheeland J. S. Wiederhott M. Wilson
*Advisor
Norfolk Southern Esco Equipment Service Company American Welding Society Norfolk Southern BNSF Railroad CNUS CNR Union Pacific Railroad Orgo-Thermit, Incorporated Canadian Pacific Railroad GKC Consulting Company Consultant TTX Company CSX Elgin Joliet & Eastern Railway Rail Maintenance Alpha Gamma Transform, Incorporated Long Island Railroad METRA Holland Company BNSF Bodycoate Union Pacific Railroad The Lincoln Electric Company LTK Norfolk Southern CSX Transportation DMER RR Association of American Railroads Track-Weld Industries Stoody Company Union Pacific Railroad Burlington Northern CSX Transportation
--`,,``,``,`,``,```,```,,````,`-`-`,,`,,`,`,,`---
iv
Foreword
(This Foreword is not a part of AWS D15.2:2003, Recommended Practices for the Welding of Rails and Related Rail Components for Use by Rail Vehicles, but is included for informational purposes only.)
This recommended practice establishes standards for the joining, repair, maintenance and inspection of rail welds and the welding of related rail components. It was developed and is maintained by the Subcommittee on Track Welding within the AWS Committee on Railroad Welding. The welding of rails and related rail components for use by rail vehicles is vital to the safe and economical operation of American railroads. This subcommittee has endeavored to develop these recommended practices to serve as a guideline for the railroad and related industries in the establishment of track welding specifications. The subcommittee is made up of individuals from all segments of the railroad industry, both users and suppliers, and representatives of both the Association of American Railroads and the American Railway Engineering and Maintenance of Way Association. The purpose of this document is to provide a single comprehensive source of information that will be used throughout the railroad industry. It should act as a guideline towards improving welding quality through the economical joining and repair of rail and rail components. The first edition of D15.2 was published in 1994. Comments and suggestions for the improvement of this standard are welcome. They should be sent to the Secretary, AWS D15 Committee on Railroad Welding, American Welding Society, 550 N.W. LeJeune Road, Miami, FL 33126. Official interpretations of any of the technical requirements of this standard may be obtained by sending a request, in writing, to the Managing Director, Technical Services Division, American Welding Society. A formal reply will be issued after it has been reviewed by the appropriate personnel following established procedures.
v
--`,,``,``,`,``,```,```,,````,`-`-`,,`,,`,`,,`---
This page is intentionally blank.
--`,,``,``,`,``,```,```,,````,`-`-`,,`,,`,`,,`---
Table of Contents
Page No. Personnel .................................................................................................................................................................... iii Foreword ......................................................................................................................................................................v List of Tables ...............................................................................................................................................................ix List of Figures..............................................................................................................................................................ix List of Forms................................................................................................................................................................ix 1. 2. 3. Scope .....................................................................................................................................................................1 Referenced Documents .........................................................................................................................................1 Rail, Rail Components Manufactured from Rail, and Their Repair .....................................................................2 3.1 Specific Items ..............................................................................................................................................2 3.2 Welding Processes .......................................................................................................................................2 3.3 Railroad Rail Welding .................................................................................................................................2 3.4 Repair of Battered Rail Ends and Wheel Burns (Carbon Steel or Premium Steel Rail) .............................2 3.5 Repair of Rail-Type Switch Points and Switch Point Protectors ................................................................3 3.6 Frogs, Crossings, and Other Components Made From Rail Steel...............................................................4 3.7 Miscellaneous Carbon Steel and Low Alloy Steel Components .................................................................4 Repair or Fabrication of Components Manufactured from Austenitic Manganese Steel .....................................4 4.1 Metallurgical Background ...........................................................................................................................4 4.2 Components .................................................................................................................................................4 4.3 Welding Processes .......................................................................................................................................4 4.4 Filler Metals.................................................................................................................................................4 4.5 Preparation for Welding ..............................................................................................................................4 4.6 Welding RecommendationsGeneral ........................................................................................................5 4.7 Welding RecommendationsFrogs and Crossings in Track......................................................................6 Recommended Practices for Joining of Rails by Thermite Welding (TW) ..........................................................6 5.1 General Description .....................................................................................................................................6 5.2 Application ..................................................................................................................................................6 5.3 Preparation of Final Gap for Welding .........................................................................................................6 5.4 Welding Procedure ......................................................................................................................................6 5.5 Care of Thermite Materials..........................................................................................................................7 5.6 Procedure Qualification ...............................................................................................................................8 5.7 Welder Qualification ...................................................................................................................................8 5.8 Thermite Welding Safety Precautions .........................................................................................................8 Flash Welding (FW) of Rail..................................................................................................................................8 6.1 General Process Description........................................................................................................................8 6.2 Rail Preparation ...........................................................................................................................................8 6.3 Rail Welding................................................................................................................................................9 6.4 Finishing Operations....................................................................................................................................9 6.5 Continuous Welded Rail Storage.................................................................................................................9 Procedure QualificationArc Welding Processes ...............................................................................................9 7.1 Prequalified Procedures ...............................................................................................................................9 7.2 Welding Procedures.....................................................................................................................................9
4.
5.
6.
7.
vii
--`,,``,``,`,``,```,```,,````,`-`-`,,`,,`,`,,`---
Page No. 8. Track Welder QualificationArc Welding Processes .........................................................................................9 8.1 Procedure Qualification ...............................................................................................................................9 8.2 Workmanship Samples ..............................................................................................................................13 8.3 Results of the Workmanship Samples .......................................................................................................13 Nondestructive Testing .......................................................................................................................................13 9.1 Geometry Inspection (Rail Weld Alignment)............................................................................................13 9.2 Magnetic Particle Inspection .....................................................................................................................13 9.3 Ultrasonic Inspection .................................................................................................................................13 9.4 Radiography...............................................................................................................................................13 9.5 Dye Penetrant Inspection...........................................................................................................................13
9.
Nonmandatory Annexes ..............................................................................................................................................15 Annex AWelding Processes .....................................................................................................................................15 Annex BWelding of Austenitic Manganese Steel ....................................................................................................21 Annex CFlash Welding Guidance ...........................................................................................................................25 Annex DAREMA Tests for Continuous Welded Rail...............................................................................................27 Annex ESafe Practices ............................................................................................................................................31 Annex FGuidelines for Preparation of Technical Inquiries for AWS Technical Committees ................................35 List of AWS Documents on Railroad Welding ............................................................................................................37
--`,,``,``,`,``,```,```,,````,`-`-`,,`,,`,`,,`---
viii
List of Tables
Table D1 D2 D1 Page No. Processes for Carbon and Alloy Steel Rail Components ...............................................................................2 Minimum Performance Specifications for New Flash and Thermite Welded Rail .......................................7 Wheel Loads for Rolling Load Test.............................................................................................................27
List of Figures
Figure A1 A2 A3 A4 A1 A2 A3 A4 A5 A6 A7 D1 D2 Page No. Typical Weld Pattern for Rail End Repair .....................................................................................................3 Skip Welding Repair Made in 5 in. (125 mm) Long Increments ..................................................................5 Layout of Hardness Survey on Rail Head....................................................................................................10 Layout of Transverse Hardness Survey .......................................................................................................11 Shielded Metal Arc Welding (SMAW) .......................................................................................................16 Gas Metal Arc Welding (GMAW)...............................................................................................................16 Flux Cored Arc Welding (FCAW)...............................................................................................................17 Section Through a Thermite Mold and Crucible .........................................................................................18 Automatic Hydraulically Operated Flash Welding Machine with Horizontal Clamping............................18 Rail Welding Production Line .....................................................................................................................19 Oxyfuel Gas Welding (OFW) ......................................................................................................................19 Loading Arrangement for the 12 in. Stroke Rolling Load Machine ............................................................28 Load Arrangement for the Slow Bend Test and Formula for Deriving the Modulus of Rupture................29
List of Forms
Form 1 2 Page No. Typical Welding Procedure Qualification Test Record ...............................................................................12 Typical Welder Qualification Test Record ..................................................................................................14
--`,,``,``,`,``,```,```,,````,`-`-`,,`,,`,`,,`---
ix
--`,,``,``,`,``,```,```,,````,`-`-`,,`,,`,`,,`---
AWS D15.2:2003
1. Scope
This document recommends standards for the joining, repair, maintenance, inspection of rail welds, and related rail components. For the purposes of this document, rails include railroad rails, crane rails, guard rails, electrical contact rails, girder rails, and retarder rails. Classification of rails is based on the American Railway Engineering and Maintenance of Way Association (AREMA) specifications governing the manufacture of rails. Related rail components include rail crossings and turnouts which further include switch points, stock rails, switch point guards, spacer blocks, connecting rods, switch rods, plates, frogs, and frog components. The use of track components reconditioned by welding is a decision of the rail owner outside the scope of this document. This document does not include road bed maintenance except where it affects the expected life of the repair. Safety precautions shall conform to Code of Federal Regulations (CFR), Title 49, Part 214, Railroad Workplace Safety. Safety and health issues and concerns are beyond the scope of this standard, and therefore are not fully addressed herein. Safety and health information is available from other sources, including, but not limited to, ANSI Z49.1, Safety in Welding, Cutting, and Allied Processes, and applicable federal and state regulations (see also Annex E, Safe Practices). Welding processes include shielded metal arc welding (SMAW), gas metal arc welding (GMAW), flux cored arc welding (FCAW), flash welding (FW), thermite welding (TW), and oxyfuel gas welding (OFW). See Annex A and Volume 2, Eighth Edition, Welding Handbook for details. This standard makes use of the U.S. Customary Units. Approximate mathematical equivalents in the International System of Units (SI) are provided for comparison in parentheses ( ) or in appropriate columns in tables and figures.
this AWS standard. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this AWS standard are encouraged to investigate the possibility of applying the most recent editions of the documents shown below. For undated references, the latest edition of the standard referred to applies. (1) ANSI Z49.1, Safety in Welding, Cutting, and Allied Processes, Volume 2, Eighth Edition, Welding Handbook1 (2) AREMA Chapter 4, Rail 2 (3) ASTM E 140, Hardness Conversion Tables for Metals (Relationship Among Brinell Hardness, Vickers Hardness, Rockwell Hardness, Rockwell Superficial Hardness, Knoop Hardness, and Scleroscope Hardness) 3 (4) ASTM E 164-97, Standard Practice for Ultrasonic Contact Examination of Weldments (5) ASTM E 1417-99, Standard Practice for Liquid Penetrant Examination (6) ASTM E 709-01, Standard Guide for Magnetic Particle Examination (7) AWS A5.13, Specification for Surfacing Electrodes for Shielded Metal Arc Welding2 (8) AWS A5.21, Specification for Composite Surfacing Welding Rods and Electrodes (9) Code of Federal Regulation, Title 49, Volume 4, Parts 200299, revised October 1, 2000.4
1. ANSI Z49.1 and AWS documents are available from Global Engineering, 15 Inverness Way East, Englewood, CO 801125776; telephones: (800) 854-7179, (303) 397-7956; fax (303) 397-2740; Internet: www.global.ihs.com. 2. AREMA documents are available from the American Railway Engineering and Maintenance of Way Association, 8201 Corporate Drive, Suite 1125, Landover, MD 20785-2230. 3. ASTM documents are available from the American Society for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA 19428. 4. Federal regulations are available from the U.S. Government Bookstore, Wells Fargo Building, 201 West 8th, Pueblo, CO 81003, or http://www.gpo.gov/.
2. Referenced Documents
The following standards contain provisions which, through reference in this text, constitute provisions of
--`,,``,``,`,``,```,```,,````,`-`-`,,`,,`,`,,`---
1
AWS D15.2:2003
3. Rail, Rail Components Manufactured from Rail, and Their Repair

It is essential to identify the track material to attain optimum results in selecting the welding procedure. 3.1 Specific Items. These recommendations apply to, but are not limited to, the items listed in Section 1. 3.2 Welding Processes. Welding processes include shielded metal arc welding (SMAW), gas metal arc welding (GMAW), flux cored arc welding (FCAW), flash welding (FW), thermite welding (TW), and oxyfuel gas welding (OFW). 3.3 Railroad Rail Welding 3.3.1 Railroad Rail Grades 3.3.1.1 Carbon steel rail having a minimum hardness of 240 HB. 3.3.1.2 Premium steel rail has a nominal hardness exceeding 341 HB. This hardness may be the result of alloy composition (nonheat treated) or heat treatment process. Heat treated rail and other variations may require special welding procedures as recommended by the rail manufacturer or filler metal producer, or both. 3.3.1.3 Electrical contact rails are low-carbon steel rails without hardness requirements. 3.3.2 Procedure Requirements for Arc Welding of Carbon Steel and Premium Steel Rail 3.3.2.1 Preheating the weld areas to 800F1000F (425C540C), as measured immediately before welding, is recommended to equalize temperature in the workpiece to prevent breakout of material. 3.3.2.2 Interpass temperature should be within the same range as the preheat temperature to maintain temperature in the workpiece. 3.3.2.3 Filler metal should provide weld metal having a nominal surface hardness compatible with the existing base metal to eliminate breakout of the weld. 3.3.2.4 Postweld heat treatment is recommended, to prevent hardening and cracking when a part is cooled too rapidly through the transformation range, but is not required unless dictated by past experience or by approved railroad welding procedures. 3.3.3 Procedure Requirements for Arc Welding of Premium Steel Rail 3.3.3.1 A preheating temperature of 800F1000F (425C540C) is recommended for premium steel rail. There are two reasons this is done: (1) To equalize temperature in the workpiece.
(2) To prevent hardening and cracking when a part is cooled too rapidly through the transformation range. 3.3.3.2 The required cooling rate depends on rail size and chemical composition, filler metal, and ambient welding temperature. 3.4 Repair of Battered Rail Ends and Wheel Burns (Carbon Steel or Premium Steel Rail) 3.4.1 Carbon steel or premium steel rail may be repaired using a process selected from 3.2 and Table 1. 3.4.2 Rail Preparation 3.4.2.1 Visually inspect the rail to determine repairability in accordance with the rail owners policy. 3.4.2.2 Defective material should be removed to sound base metal. Soundness may be checked using dye penetrant or magnetic particle testing (see Section 9). 3.4.3 Welding Procedure 3.4.3.1 As outlined in 3.3.2 or 3.3.3, preheat the repair area plus 4 in.6 in. (100 mm150 mm) longitudinally beyond the weld area in both directions. 3.4.3.2 Interpass temperature should be within the same range as the preheat temperature to maintain temperature in the workpiece. 3.4.3.3 All the above recommended temperatures are dependent on the base metal composition, the filler metal used, ambient temperature, weather conditions, and the manufacturers recommendations. 3.4.3.4 Weld beads should be made primarily in the longitudinal direction for proper heat distribution. 3.4.3.5 Diagonal or chevron weld bead patterns are preferred, see Figure 1 for typical chevron pattern.
Component Material Carbon steel
Processes Shielded metal arc welding (SMAW) Gas metal arc welding (GMAW) Flux cored arc welding (FCAW) Oxyfuel gas welding (OFW) Flash welding (FW) Thermite welding (TW) Shielded metal arc welding (SMAW) Gas metal arc welding (GMAW) Flux cored arc welding (FCAW) Flash welding (FW) Thermite welding (TW)
Premium steel
2
--`,,``,``,`,``,```,```,,````,`-`-`,,`,,`,`,,`---
Table 1 Processes for Carbon and Alloy Steel Rail Components
AWS D15.2:2003
3.5 Repair of Rail-Type Switch Points and Switch Point Protectors 3.5.1 Repair of austenitic manganese switch points is not recommended because the heat input cannot be controlled properly to control distortion. 3.5.2 Carbon steel and premium steel rail components may be welded by the processes shown in Table 1. 3.5.3 Visually inspect the switch point or switch point protector to determine the reparability in accordance with the rail owners policy. 3.5.4 Defective material should be removed to sound base metal. Soundness may be determined by dye penetrant or magnetic particle testing (see Section 9). 3.5.5 Temperature control is extremely critical because of variations in thickness and the need to minimize distortion. In order to minimize distortion of the switch point and stock rail during cooling, pre-and post heating should be balanced over the base/web intersection and the repair area. 3.5.6 Switch Point Repair Procedure 3.5.6.1 Welding the switch point against a stock rail is not recommended because of the possibility of arc strikes on the stock rail. A copper backing plate should be used. 3.5.6.2 Switch point must be protected from traffic movement during welding, cooling, and finish grinding.
--`,,``,``,`,``,```,```,,````,`-`-`,,`,,`,`,,`---
Figure 1Typical Weld Pattern for Rail End Repair
3.5.6.3 When using arc welding processes, hammer shaping of repaired carbon steel, alloy or heat treated rail switch points is not recommended to prevent hot tearing at the grain boundaries of the weld. 3.5.7 Preheat Procedure. Preheat the switchpoint assembly in the weld areas, as measured immediately before welding, to 800F1000F (425C540C) unless otherwise recommended by the rail owner. To equalize temperature in the workpiece and prevent breakout of material. If there are differences between the recommendations of the rail owner and this document, the rail owners recommendation shall prevail. 3.5.8 Interpass temperature shall be in the same range as the preheat temperature. To maintain temperature in the workpiece. 3.5.9 Application of Filler Metal 3.5.9.1 Longitudinal lineal stringer beads are recommended for carbon steel rail. Slight oscillation resulting in slower lineal travel speed and increased lineal heat input may be beneficial for premium steel rails to maintain Interpass temperature. Weld bead pattern shall be in
3.4.3.6 Provisions must be made to prevent permanent distortion of the weld area. 3.4.3.7 All weld craters shall be filled. 3.4.3.8 Arc strikes shall not be permitted outside the preheated repair area. Accidental arc strikes outside the repair area shall be repaired in accordance with the provisions of 3.4. 3.4.4 Finish Grinding 3.4.4.1 Welds should be finish ground according to approved procedures on the same work day the rail is welded to minimize impact loading and prevent weld deformation. 3.4.4.2 Finished surface of the weld should be smooth and uniform to match the existing rail contour.
3
AWS D15.2:2003
accordance with the operating procedures of the specific railroad. 3.5.9.2 All welds shall be finished to the approved contour. 3.5.9.3 Arc strikes shall not be permitted outside the preheated weld repair area because they may cause cracks. Accidental arc strikes outside the repair area shall be repaired according to 3.5. 3.6 Frogs, Crossings and Other Components Made from Rail Steel. Practices outlined in 3.4 are applicable. 3.7 Miscellaneous Carbon Steel and Low Alloy Steel Components. Practices outlined in 3.4 may be applicable.
deposit undiluted weld metal with manganese content in excess of 14% plus smaller additions, alone or in combination, of nickel, molybdenum, chromium, or vanadium. 4.4.2.3 The range of properties developed by these electrodes enables the user to select the combination best suited for the particular application. For example, an overlay with relatively high yield strength might be used to build up the running surface of frogs whereas an alloy with a yield strength more closely matching that of the base metal might be used to repair a deep crack. 4.4.3 Special chromium-nickel-iron and chromiummanganese-nickel-iron austenitic electrodes are acceptable to weld austenitic manganese base metal. 4.5 Preparation for Welding 4.5.1 Austenitic Manganese Steel Castings 4.5.1.1 Grease, rust, and dirt should be removed from the surfaces by appropriate means. 4.5.1.2 The entire casting should be inspected for cracks and other defects. Dye penetrant testing may be used to locate and define the cracks (see Section 9). 4.5.1.3 Cracks shall be removed as completely as practical by grinding or air arc gouging. The latter is the preferred process. Air arc gouging procedures should be as follows: (1) Locate the end of the crack using a shallow cut. (2) Make a deeper cut moving from the end of the crack towards the edge of the casting. (3) If the crack does not extend to the edge, air arc gouging should proceed from the ends towards the middle of the crack. (4) Gouging should be continuous utilizing straight rapid cuts. (5) Metal and oxides should be eliminated from the cut groove by grinding. (6) Groove should be kept just wide enough to permit electrode manipulation during welding. (7) Base metal temperature should not exceed 500F (260C) at a point 1 in. (25 mm) from the area being gouged. 4.5.1.4 Worn areas should be located and marked using a straight edge or template. 4.5.1.5 Work hardened (plastically deformed) metal should be removed (this includes weld deposits impacted by traffic during repair). 4.5.1.6 Sharp edges along flangeway surfaces should be rounded slightly. 4.5.2 For Castings to be Welded in Track. Track conditions that may have contributed to the damaged or worn casting shall be corrected prior to welding.
4. Repair or Fabrication of Components Manufactured from Austenitic Manganese Steel

4.1 Metallurgical Background. For a general discussion of the welding of austenitic manganese steel see Annex B. 4.2 Components. Austenitic manganese steel components include but are not limited to frogs, crossings, switch point guards, casting inserts, and bridge track components. If composition of the component is in doubt, a hand magnet should be used for identification purposes. An austenitic manganese steel component will be nonmagnetic, or at the most, have a slightly magnetic skin. The carbon steel or low alloy steel component will be strongly magnetic. 4.3 Welding Processes 4.3.1 Manual welding processes are restricted to shielded metal arc welding electrodes. 4.3.2 Semiautomatic welding processes refer to flux cored arc welding. 4.4 Filler Metals 4.4.1 Austenitic manganese steel shall not be surfaced nor joined using carbon steel or low alloy steel welding electrodes or welding wires. 4.4.2 Austenitic Manganese Welding Electrodes 4.4.2.1 AWS A5.13, Specification for Surfacing Electrodes for Shielded Metal Arc Welding, and AWS A5.21, Specification for Composite Surfacing Welding Rods and Electrodes, detail several basic compositions. 4.4.2.2 AWS A5.13 and AWS A5.21 reflect the variety of modifications of the basic austenitic manganese composition currently available. The electrodes generally
--`,,``,``,`,``,```,```,,````,`-`-`,,`,,`,`,,`---
4
AWS D15.2:2003
4.5.3 For Castings to be Shop Repaired 4.5.3.1 Rail-bound frogs should be stripped before examination for cracks. 4.5.3.2 Distortion control procedures such as preor postweld bending should be considered by the repair shop. 4.6 Welding RecommendationsGeneral The repair of each worn casting tends to be an individual job not subject to rigid definition. Therefore, the recommendations of this section are of a general nature applicable to a wide variety of applications. 4.6.2 When the casting temperature is below 32F (0C), it shall be warmed to approximately 70F (21C) before any welding or gouging. To prevent embrittlement of the base metal, interpass temperatures should not exceed 500F (260C) at a point 1 in. (25 mm) from the area being welded. 4.6.3 Diameter of covered electrodes for SMAW should not exceed 3/16 in. (5 mm). 4.6.4 Diameter of flux cored wire for semiautomatic welding should not exceed 7/64 in. (2.8 mm). 4.6.5 Welding current and travel speed should be appropriate to ensure adequate penetration, bead tie-in and lowest thermal input. Excess current should be avoided to prevent heat buildup. 4.6.6 Arc length should be maintained as short as possible while maintaining good arc characteristics. 4.6.7 Weld beads should be slightly crowned and no more than 5/8 in. (16 mm) in width. 4.6.8 Length of individual weld bead should not exceed 10 in. (250 mm) when welding in track. In the shop where precautions can be taken to minimize distortion and heat buildup, longer welds are permitted. 4.6.9 Heat input into the casting should be monitored frequently. Welding should be discontinued in any area where the casting temperature exceeds 500F (260C) measured 1 in. (25 mm) from the weld area. 4.6.9.1 Quenching is recommended to prevent overheating the casting. 4.6.9.2 Skip welding should be used to minimize heat buildup, (see Figure 2). 4.6.10 Carbon blocks or copper plates may be used in the flangeways to maintain proper contour and minimize finish grinding. 4.6.11 Flangeway beads should be deposited first. 4.6.12 Adjacent beads should have tie-in by 3550%. 4.6.13 The direction of successive beads should be reversed to minimize stress buildup. 4.6.14 The end of welds should be staggered to further minimize stress buildup. 4.6.15 Weld beads should not be started or stopped at the edge of the casting to prevent weld undercut.
--`,,``,``,`,``,```,```,,````,`-`-`,,`,,`,`,,`---
WING RAIL
2 3
1 4
2 3
1 4
FROG POINT
4 3 4 5 in. (125 mm )
2 4 3 4
1 3
2 4
1 3
2 4
WING RAIL
1st WELD BEADS 2nd WELD BEADS 3rd WELD BEADS 4th WELD BEADS
Figure 2Skip Welding Repair Made in 5 in. (125 mm) Long Increments
4.6.16 Weld beads on frog wings, or points should be parallel to the flangeways. 4.6.17 The general procedure for welding frog points is as follows: 4.6.17.1 Welding should start at the lowest point of the repair area gradually building up to the full width of the repair to maintain weld integrity. 4.6.17.2 The arc should be struck about 1/2 in. (13 mm) ahead of the direction of travel where the beads are to begin. 4.6.17.3 Craters should be filled by reversing direction and welding back into the bead before breaking the arc. 4.6.18 Successive layers of austenitic manganese may be applied to achieve the desired thickness of buildup. 4.6.19 Individual layers of weld metal should be visually examined prior to proceeding with the next layer.
5
AWS D15.2:2003
Any unacceptable indications should be repaired prior to starting the next layer. 4.6.20 If defect removal requires grinding through the thickness of the casting, a back-up bar of austenitic manganese steel should be used to provide a base for welding. 4.6.21 Specially modified stainless steel may be used as a root pass or initial pass. 4.7 Welding RecommendationsFrogs and Crossings in Track 4.7.1 The general recommendations of 4.6 should apply, as applicable. 4.7.2 Safe movement of trains while frogs are being repaired should be the first priority. 4.7.2.1 Cracks and major break-out areas should be repaired prior to the buildup of worn areas. 4.7.2.2 Large areas to be welded should be subdivided into sections in such a way that train movement will not be disrupted. 4.7.2.3 The guards of self-guarded frogs shall be rebuilt to their original dimension prior to other repairs. Enough time should be allowed between traffic movements to allow complete welding and finish grinding of the raised guard. After the guards have been repaired, the tread portion should be restored. 4.7.2.4 Immediately after completing each bead, peen the bead with the ball end of a two pound ball-peen hammer to stress relive the weld bead. The bead should be struck two to four times per inch of weld using moderate blows that produce an indentation of approximately 0.040 in. (1.0 mm). Peening should start at the crater and proceed toward the start of the weld. Do not peen the first bead layer, to prevent damage between the bead interface and the parent material. Do not peen the final layer to prevent blemishes in the finished surface.
5.1 General Description. Thermite welding is a welding process that joins rail ends by melting them with superheated liquid metal from a chemical reaction between iron oxide and aluminum. Filler metal is obtained from the liquid metal (see Figure A5). 5.1.1 For a general discussion of the process, see Volume 2, Eighth Edition, Welding Handbook. 5.1.2 Thermite welding supplies are sold under a number of commercial trade names. 5.2 Application 5.2.1 Application includes, but is not limited to, items listed in Section 1. 5.2.2 The thermite welding process may be utilized to weld both carbon steel rail and premium steel rail. pecial procedures may be necessary when welding alloy steel premium rail. to prevent hardening and cracking when the weld is cooled too rapidly through the transformation range. 5.3 Preparation of the Final Gap for Welding 5.3.1 Rail ends should be aligned properly, both laterally and vertically. Rail ends should be secured to prevent movement during the welding process. 5.3.2 The root opening between rails may be oxyfuel gas cut, sawed, or cut with an abrasive disc. Of these, oxyfuel gas cutting is the least desirable. 5.3.2.1 If the final gap is to be prepared by OFC, the rail should be preheated to 700F (370C) prior to the oxyfuel gas cut to prevent cracking. 5.3.2.2 Care should be exercised to ensure smooth cut surfaces. An end squareness of 1/16 in. (2 mm) both horizontally and vertically is recommended. 5.3.2.3 Ends of oxyfuel gas cut rails should be cleaned thoroughly to remove all residual oxide and must be welded prior to cooling. 5.3.3 The root opening between the rail end faces may vary depending on the specific commercial process. 5.3.4 At least 6 in. (150 mm) on each side of the gap should be free of all moisture and foreign substances such as dirt, grease, loose oxide, burns, fins, and metal flow. In addition, a 6 in. (150 mm) hole free zone is recommended. 5.3.5 Copper material from track circuit bonds shall be removed for at least 2 in. (50 mm) on each side of the weld area. 5.4 Welding Procedure. Welding procedure including preheating techniques, method of ignition, rate of cooling, and mold removal will vary somewhat depending on the instructions of the manufacturer of the specific ther-
5. Recommended Practices for Joining of Rails by Thermite Welding (TW)

Thermite is defined as a mixture of finely divided aluminum and iron oxide. When the aluminum and iron oxide react, the reaction is called a thermite reaction. Thermite welding is accomplished with the heat produced by the thermite reaction. Filler metal is obtained from the combination of the iron reaction product and pre-alloyed shot in the mixture.
--`,,``,``,`,``,```,```,,````,`-`-`,,`,,`,`,,`---
6
AWS D15.2:2003
mite kit being employed and the type, size and chemical composition of the specific rail being welded, as well as the local service conditions. 5.4.1 Welds made in accordance with 5.4 should be subjected to the following tests and meet the minimum requirements as specified in Table 2: (1) Slow bend tests to determine load and deflection (see Annex D) (2) Hardness tests to evaluate resistance to wear and deformation (see Figure 3)
(3) Rolling load test to determine fatigue life (see Annex D) at the customers option 5.5 Care of Thermite Materials 5.5.1 DANGER: INTRODUCTION OF MOISTURE TO THE THERMITE WELDING PROCESS MAY CAUSE SERIOUS OR FATAL INJURY. Molten steel and hot slag can cause serious explosion upon coming into contact with snow, ice, standing water, frozen ballast or soil.
Table 2 Minimum Performance Specifications for New Flash and Thermite Welded Rail
Slow Bend Testing Flash Welding Material Soft Carbon Rail (248 HB Min.) Standard Carbon Rail (300 HB Min.) Premium Steel Rail (341 HB Min.) Modulus of Rupture(1) 100 000 psi (689 MPa) 120 000 psi (827 MPa) 125 000 psi (862 MPa) Deflection Min. 1.5 in. (38 mm) 1.0 in. (25 mm) 0.7 in. (19 mm) Optional Rolling Load Test Material All rails Loads See Table D1 Hardness Survey(2) Flash Welding Material Standard Carbon Rail Premium Steel Rail Deviation from Parent Material, through HAZ Area +40 HB/60 HB to maximum 410 HB +60 HB/80 HB to maximum 415 HB Thermite Welding The hardness of the weld metal shall be within 30 HB points of the manufacturer's specified hardness for the specific welding kit being used. Macroetch (Flash Welded Rail Only) Structure Flow-Line Grain turn-out angle Parallel Heat-Affected Zone
Notes: ( 9 Load psi ) (1) Modulus of Rupture = ---------------------------------------Section Modulus (2) Measurements may be taken in Rockwell Hardness Numbers and converted to Brinell Hardness These conversions be done according to Table 1 in ASTM E 140. Numbers providing a minimum of five Rockwell Hardness readings are obtained, discarding the highest and lowest reading and averaging the remaining readings.
Thermite Welding Modulus of Rupture(1) 100 000 psi (689 MPa) 110 000 psi (758 MPa) 120 000 psi (827 MPa) Deflection Min. 1.0 in. (25 mm) 0.9 in. (23 mm) 0.6 in. (15 mm)
--`,,``,``,`,``,```,```,,````,`-`-`,,`,,`,`,,`---
Cycles 2 000 000
Specification 3575 6.350 mm (0.25 in.) maximum deviation
7
AWS D15.2:2003
5.5.2 Molds shall be protected from moisture contamination and freezing during storage. Charges shall be protected from moisture contamination during storage. 5.5.3 Charges and molds shall be protected from moisture contamination during transportation from storage to work site. 5.5.4 Molds and charges shall be used within the shelf-life period recommended by the manufacturer 5.5.5 Crucibles (reaction chambers) shall be clean and dry at all times. 5.5.6 Crucible, mold, charge, and adjacent rail area shall be protected from moisture. 5.5.7 Rail weld geometry shall be checked with a straight edge and taper gauge in accordance with the requirements of AREMA 4-2.5, Specification for Quality Assurance of Thermite Welding of Rail, or those selected by the operating authority. 5.5.8 Alignment and Finish Requirements 5.5.8.1 Alignment tolerance of running surfaces should be within the requirement of the individual railroad. 5.5.8.2 Additional grinding to remove surface defects should be kept to a minimum. 5.5.8.3 If required, a light grinding of the weld collar area to remove sharp corners or surface blemishes is permissible. Care should be exercised to prevent aggressive grinding. All grinding of the weld collar should be symmetrical, the as cast geometry should be left intact. 5.5.8.4 Radiography is not recommended for inspection of thermite welds. Defects are very difficult to detect and interpret. 5.5.8.5 Visual and ultrasonic examinations of finished welds are recommended. 5.6 Procedure Qualification. Procedure tests performed by the thermite manufacturer may be accepted by the user if individual testing is not feasible. 5.7 Welder Qualification 5.7.1 Prior to qualification, welders should receive training from qualified instructors. 5.7.2 In the absence of established welder qualification tests, the welding supervisor should determine the tests required. 5.7.3 Results of the evaluation of the welder should be made a part of the operators permanent record.
5.8 Thermite Welding Safety Precautions 5.8.1 Over tightening the base plate or mold clamp screws may cause cracking of the mold and subsequent leaking of molten metal. 5.8.2 Improper or careless luting (sealing) of the mold may cause leakage of the molten metal. 5.8.3 Avoid all contact with moisture. Molten steel and slag can cause serious explosions when contacted by any form of moisture. 5.8.4 Personnel must wear approved personal safety equipment at all times. 5.8.5 Slag basin should be emptied only after the slag has completely solidified. Solid slag should be disposed of in such a manner as not to pose any hazard to operating personnel.
6. Flash Welding (FW) of Rail

6.1 General Process Description 6.1.1 The automated resistance welding process (see Figures A6 and A7) heats and prepares the rail ends, provides a non-oxidizing environment, and forges the rail ends into a welded joint. Critical flash welding parameters are shown in Annex C. 6.1.2 The process and related equipment may contain the following operations: preparation, preheating, flashing, forging, shearing, postweld heat treatment, and finishing. 6.1.3 Chapter 4 Part 2 of The American Railway Engineering and Maintenance of Way Association (AREMA) Manual [4-2.2 Specification for Fabrication of Continuous Welded Rail] provides minimum specifications for rail welding. 6.2 Rail Preparation 6.2.1 Rail ends should be free of rust, dirt, grease, or other foreign material that would impede the start of a low-voltage electric arc. 6.2.2 Electrode contact points should be free from rust, slag, and raised lettering that might provide added resistance to the flow of high electric current and thus cause electrode burns on the rail. 6.2.3 An electrode burn on welded rails shall be defined as follows: (1) Any electrode contact areas which have transformed to martensite, (2) Any electrode contact areas which have been displaced during welding, and
--`,,``,``,`,``,```,```,,````,`-`-`,,`,,`,`,,`---
8
AWS D15.2:2003
(3) Any electrode contact areas which contain transferred electrode copper. 6.2.4 Rails should be presented to the stations of the welding plant in a consistent manner to enhance production and performance. 6.2.5 Rails should be grouped by length, composition, type, and wear to minimize adjustments required by operating personnel. 6.3 Rail Welding 6.3.1 Railroad rails shall be flash butt welded using only the following: (1) A previously qualified welding procedure. (2) Welding equipment certified as being able to consistently reproduce the required welding program. (3) A qualified operator able to set up the welding program dictated by 6.3.1, calibrate the monitoring equipment, and maintain the machine. (4) Acceptable welds shall qualify the welding procedure, the welding equipment or the welding operator. 6.3.2 Welds made in accordance with 6.3.1 should be subjected to the following tests and meet the minimum requirements as specified in Table 2: (1) Slow bend tests to determine load and deflection (see Annex D) (2) Hardness tests to evaluate resistance to wear and deformation (see Figure 3) (3) Macroetch tests to determine metallurgical soundness, forging patterns, and heat-affected zone (HAZ) (see Figure 4) (4) Rolling load test to determine fatigue life (see Annex D) at the customers option (5) Microetch examination to evaluate metallurgical quality at the customers option 6.3.3 Test welds and the results should be evaluated by qualified personnel designated by the engineer in charge and experienced in the flash welding of rail before production welds are made. 6.3.4 Production operations should be monitored by an inspector to ensure compliance with specifications. 6.3.5 Weld parameters for each weld shall be recorded. 6.3.5.1 Recorders should be calibrated daily before use. 6.3.5.2 These permanent records should be retained by the verification inspector, operating authority or manufacturer. 6.3.5.3 Records shall be compared with those certified by qualified personnel during qualification testing.
--`,,``,``,`,``,```,```,,````,`-`-`,,`,,`,`,,`---
6.3.6 Table 2 lists a number of tests that may be used to evaluate the quality of maintenance welds. 6.3.7 Final inspection of the welded rail (see Section 9) shall be done at the last station of the welding plant prior to acceptance for transportation and installation (see Figure A7). 6.4 Finishing Operations 6.4.1 Excess weld material shall be removed. 6.4.2 Finished contour should be as specified by qualified personnel. In the absence of specific instructions, the requirements of AREMA Specifications 4-2.2 should apply. 6.5 Continuous Welded Rail Storage 6.5.1 A point person should safely guide and monitor transfer of the welded rail string from the production line into, or onto, the storage rack, ground storage, or continuous welded rail (CWR) train. 6.5.2 Care should be exercised to prevent kinking the rail string. 6.5.3 Rail strings should be supported at 25 ft35 ft (811 m) intervals to prevent bending during handling and storage.
7. General Procedure Qualification Arc Welding Processes

Each welding process has its own qualification. 7.1 Prequalified Procedures. There are no prequalified procedures for railroad track maintenance welding. 7.2 Welding Procedures. Each operating authority or railroad service company should develop a welding procedure for each specific application, base metal, and process combination in accordance with the general guidelines of this document. Qualified welding procedures may be utilized at any location within the individual authority. Welding procedure should be documented on a form, or forms, equivalent to Form 1. All tests may not be required, but selected tests shall be performed as agreed between the contractor and operating authority.
8. Track Welder QualificationArc Welding Processes

8.1 Procedure Qualification. Any track welder who successfully performs the procedure qualification shall be qualified to perform the same operations in production.
9
AWS D15.2:2003
SI EQUIVALENTS in. 1/8 1/4 mm 3 6
Figure 3Layout of Hardness Survey on Rail Head
10
--`,,``,``,`,``,```,```,,````,`-`-`,,`,,`,`,,`---
AWS D15.2:2003
--`,,``,``,`,``,```,```,,````,`-`-`,,`,,`,`,,`---
SI EQUIVALENTS in. 1/4 5/8 mm 6 16
Figure 4Layout of Transverse Hardness Survey
11
AWS D15.2:2003
Form 1 Typical Welding Procedure Qualification Test Record

PROCEDURE SPECIFICATION Base Material Description ________________________ Welding Process _______________________________ Manual / Semi-Automatic ________________________ Position of Welding _____________________________ Filler Metal Description __________________________ Filler Metal Chemical Composition _________________ Filler Metal AWS Classification ____________________ Single or Multiple Pass __________________________ Max/Min Base Metal Temperature _________________ Preheat Temperature ___________________________ Interpass Temperature __________________________ Shielding Gas _________________________________ EXAMINATION Post Heat Temperature __________________________ Welding Current _______________________________ Welding Voltage _______________________________ Welders Name ________________________________ VISUAL INSPECTION OF WELD Appearance___________________________________ Undercut _____________________________________ Porosity ______________________________________ Foreign Material Inclusion ________________________ HARDNESS GRADIENTS Base Metal Hardness____________________________ Filler Metal Hardness ____________________________ HAZ Metal Hardness ____________________________
ULTRASONIC EXAMINATION UT Report No. _________________________________
METALLOGRAPHY Macroetch Size 1.________________ 2. ___________ Microetch detail ________________________________
All Weld Metal Strength Details Tensile Strength (psi) ____________________________ Yield Point Strength (psi) _________________________ Elongation in 2 in., % ____________________________ Reduction in Area, % ____________________________
WELDING PROCEDURE Pass No. Electrode/ Wire Size Welding Current Amperes/Volts Bead Size Max Bead Length Speed of Travel
WELD DETAIL
We the undersigned certify that the statements in this record are correct and that the test welds were prepared, welded, and tested in accordance with the requirements of AWS D15.2: (____________) year. Procedure No. _________________________________ Revision No. __________________________________ Railroad or Contractor ___________________________ Authorized by __________________________________ Date _________________________________________
12
--`,,``,``,`,``,```,```,,````,`-`-`,,`,,`,`,,`---
AWS D15.2:2003
8.2 Workmanship Samples. All track welders should prepare one or more workmanship samples or demonstrate on-track welding skill test to verify performance for the welding supervisor. Qualified personnel designated by the engineer in charge may determine the type, size, and number of the workmanship samples. 8.3 Results of the Workmanship Samples. Results of the evaluation of the workmanship samples or on-track skill test should be recorded and made part of the permanent qualification record of the track welder (see example Form 2).
and for the presence of free cementite. Testing shall be in accordance with ASTM E 709, Standard Guide for Magnetic Particle Examination, and performed below 800F (427C). Cementite will not be indicated at a temperature below 400F (205C). Results of the inspection shall meet or exceed the requirements of the operating railroad. 9.3 Ultrasonic Inspection. Ultrasonic inspection is best suited for inspection of welds installed in the field. It may be used, with reservations, in the production line. Results of the inspection shall meet or exceed the requirements of the operating railroad. Examination should follow established guidelines of ASTM E 164, Standard Practice for Ultrasonic Contact Examination of Weldments. 9.4 Radiography. Radiography is not recommended for the inspection of rail welds. Defects are very difficult to detect and interpret. 9.5 Dye Penetrant Inspection. Dye penetrant inspection may be used for detection of discontinuities, such as lack of fusion, corrosion, cracks, laps, cold shuts and porosity that are open or connected to the surface. Testing shall be in accordance with ASTM E 1417, Standard Practice for Liquid Penetrant Examination.
9. Nondestructive Testing
9.1 Geometry Inspection (Rail Weld Alignment). Rail weld geometry shall be checked with a straight edge and taper gauge in accordance with the requirements of AREMA 4-2.2 or those selected by the operating authority. If alignment adjustments are required they shall be performed at a temperature below 900F (482C). 9.2 Magnetic Particle Inspection. Magnetic particle inspection shall be used to inspect for surface defects such as piped rail, shear tears, craters pushed to the surface,
--`,,``,``,`,``,```,```,,````,`-`-`,,`,,`,`,,`---
13
AWS D15.2:2003
Form 2 Typical Welder Qualification Test Record

Welders Name _____________________________________________________ Welders ID No. ________________ Welding Process _________ Manual ________________ Semiautomatic __________ Machine _______________ Position _________________________________________________________________________________________ In Accordance With Procedure Specification No. _________________________________________________________ Material Specification ______________________________________________________________________________ Rail Size ________________________ Switch Point Size __________________ Frog Size ____________________ Description and Size of Other Material _________________________________________________________________ FILLER METAL Specification No. __________________ Classification _____________________ F No. ________________________ Describe Filler Metal (if not covered by AWS Specification) _________________________________________________ _______________________________________________________________________________________________ Filler Metal Chemical Composition ____________________________________________________________________ Filler Metal Diameter _________________________________________________ Is Backing Plate Used? _________ VISUAL INSPECTION Appearance______________________ Undercut ________________________ Porosity______________________ ULTRASONIC INSPECTION UT Method Transducer Type Result Remarks
HARDNESS GRADIENT Base Metal Hardness ______________________________________________________________________________ Filler Metal Hardness ______________________________________________________________________________ HAZ Hardness ___________________________________________________________________________________ METALLOGRAPHY EXAMINATION Macroetch Size 1.__________________ 2.__________________ 3.__________________ 4. ______________ Macroetch Detail __________________________________________________________________________________ Microetch Detail __________________________________________________________________________________ Test Authorized by______________________________ Test Witnessed by ______________________________ Test No. ______________________________________ We the undersigned certify that the statements in this record are correct and that the welds were prepared and tested in accordance with the requirements of the American Welding Society AWS D15.2: (___________) year. Railroad or Contractor ___________________________ Date _________________________________________
14
--`,,``,``,`,``,```,```,,````,`-`-`,,`,,`,`,,`---
AWS D15.2:2003
Nonmandatory Annexes
Annex A Welding Processes

(This Annex is not a part of AWS D15.2-2003, Recommended Practices for the Welding of Rails and Related Rail Components for Rail Vehicles, but is included for informational purposes only.)
A1. Arc Welding

A1.1 Shielded Metal Arc Welding (SMAW) (Stick Welding) A1.1.1 An arc welding process with an arc between a covered electrode and the weld pool. The process is used with shielding from the decomposition of the electrode covering, without the application of pressure, and with filler metal from the electrode. A1.1.2 See Figure A1 for a schematic of the process. A1.2 Gas Metal Arc Welding (GMAW) A1.2.1 An arc welding process that uses an arc between a continuous filler metal electrode and the weld pool. The process is used with shielding from an externally supplied gas and without the application of pressure. A1.2.2 See Figure A2 for a schematic of the process. A1.3 Flux Cored Arc Welding (FCAW) A1.3.1 An arc welding process that uses an arc between a continuous filler metal and the weld pool. The process is used with a shielding gas from a flux contained within the tubular electrode, with or without additional shielding from an externally supplied gas, and without the application of pressure. A1.3.2 See Figure A3 for a schematic of the process.
from a chemical reaction between a metal oxide and aluminum, with or without the application of pressure. Filler metal is obtained from the liquid metal. A2.2 See Figure A4 for a typical thermite installation.
A3. Flash Welding (FW)

A3.1 A resistance welding process that produces a weld at the faying surfaces of a butt joint by a flashing action and by the application of pressure after heating is substantially completed. The flashing action, caused by very high current densities at small contact points between the workpieces, forcibly expels the material from the joint as the workpieces are slowly moved together. The weld is completed by a rapid upsetting of the workpieces. A3.2 In the welding of continuous rail, the flash welding machine (Figure A5) is only one station in the production cycle (Figure A6).
--`,,``,``,`,``,```,```,,````,`-`-`,,`,,`,`,,`---
A4. Oxyfuel Gas Welding (OFW)

A4.1 A group of welding processes that produces coalescence of workpieces by heating them with an oxyfuel gas flame. The processes are used with or without the application of pressure and with or without the addition of filler metal. A4.2 See Figure A7 for a schematic of the process. A5. For further discussions of the arc welding processes refer to Volume 2, Eighth Edition, Welding Handbook.
A2. Thermite Welding (TW)

A2.1 A welding process that produces coalescence of metals by heating them with superheated liquid metal
15
AWS D15.2:2003
Figure A1Shielded Metal Arc Welding (SMAW)
Figure A2Gas Metal Arc Welding (GMAW)

16
--`,,``,``,`,``,```,```,,````,`-`-`,,`,,`,`,,`---
AWS D15.2:2003
Figure A3Flux Cored Arc Welding (FCAW)

17
--`,,``,``,`,``,```,```,,````,`-`-`,,`,,`,`,,`---
AWS D15.2:2003
Figure A4Section Through a Thermite Mold and Crucible
Figure A5Automatic Hydraulically Operated Flash Welding Machine with Horizontal Clamping
18
--`,,``,``,`,``,```,```,,````,`-`-`,,`,,`,`,,`---
AWS D15.2:2003
Figure A6Rail Welding Production Line
--`,,``,``,`,``,```,```,,````,`-`-`,,`,,`,`,,`---
Figure A7Oxyfuel Gas Welding (OFW)
19
--`,,``,``,`,``,```,```,,````,`-`-`,,`,,`,`,,`---
AWS D15.2:2003
Annex B Welding of Austenitic Manganese Steel

(This Annex is not a part of AWS D15.2-2003, Recommended Practices for the Welding of Rails and Related Rail Components for Use by Rail Vehicles, but is included for informational purposes only.)
--`,,``,``,`,``,```,```,,````,`-`-`,,`,,`,`,,`---
B1. Introduction
B1.1 Austenitic manganese steel is an extremely tough, nonmagnetic alloy with properties uniquely different from those of most commonly used structural and wear resistant steels. It is the preferred material for a number of trackwork components, with frogs and crossings the most important. It has high strength and durability and resists failure under impact and heavy loading. Its capacity for work hardening is a major asset; the surface of the part hardens under impact, undergoing some deformation, while the underlying body retains its original toughness. The propagation rate of any cracks that may be initiated is extremely slow. Metal-to-metal wear resistance is excellent. Resistance to abrasive wear is good, compared to that of carbon steel and low alloy steels. B1.2 Austenitic manganese steel is available as castings, which comprise the most tonnage. Rolled plate, bars and wire, as well as electrodes for welding in various forms also are available.
Some lower carbon steel castings alloyed with molybdenum are used in special applications. For many purposes, the optimum carbon content is about 1.15%, considering foundry and heat treating problems, casting properties, and economy. The high-manganese content plays a vital role in stabilizing the austenite by retarding its transformation to other structures. Silicon is present mainly for deoxidization purposes. Phosphorus is restricted because of its tendency to promote hot cracking, both in the foundry and in subsequent welding operations. Composition of filler metals deposited by austenitic manganese electrodes differ from casting analyses to provide the desired austenitic structure with weld cooling rates. Carbon commonly is somewhat reduced and additional alloying elements are added to maintain acceptable mechanical properties. Nickel, molybdenum, chromium, and vanadium, alone or in combinations, are used as added alloying elements in austenitic manganese steel welding electrodes.
B2. Composition
A number of modifications of the original Hadfield composition are produced commercially as castings; the ASTM A 128, Standard Specification for Steel Castings, Austenitic Manganese, lists ten grades. For trackwork castings the American Railway Engineering and Maintenance of Way Association (AREMA) requires production in conformance with ASTM A 128, Standard Specification for Steel Castings, Austenitic Manganese, except that the chemical requirements are modified slightly as follows: Carbon Manganese Silicon Phosphorus 1.00/1.30% 12.00% Min 1.00% Max 0.07% Max
B3. Basic Metallurgy

B3.1 At high temperatures, the structure of steel is essentially austenitic; most carbon steels and alloy steels transform from the austenitic structure to other structures as the metal cools. Large manganese additions effectively suppress the transformation of austenite, so that with sufficiently fast cooling an austenitic structure is retained at room temperature. B3.2 Before heat treatment, manganese steel castings are relatively brittle, as slow cooling in the molds does not provide a fully austenitic structure. Heat treatment involves heating to the appropriate austenitizing temperature, usually in the 1850F1950F (1010C1065C) range, holding until the sections are fully austenitic and all carbides dissolved, and quenching in cold, agitated water.
21
AWS D15.2:2003
B3.3 The microstructure of properly quenched manganese steel consists of distinct grains of austenite. Excessive carbides in the grain boundaries or in other manifestations are undesirable, as the mechanical properties of the steel will be lower than normal. Either inadequate austenitizing or too slow cooling from the austenitizing temperature can result in excessive carbides. B3.4 The reheating of manganese steels can also cause carbide precipitation and impaired properties, with the degree of embrittlement dependent upon both the exposure time and temperature. This is the reason for welding procedures which avoid prolonged overheating of weldments.
B5.3 Work Hardening Characteristics. In comparing manganese steels to other steels, their very high capacity for work hardening must be considered. The hardness can increase from about 200 Brinell to a maximum of about 550 Brinell, with an accompanying increase in yield strength. Work hardening is produced by deformation and allowance must be made for the metal flow that occurs, either in design or by maintenance practices. For trackwork buildup, electrodes which provide deposits considerably higher in yield strength than cast manganese steels can be used to minimize but not eliminate deformation in service.
B4. Physical Properties

B4.1 Magnetic Characteristics. The untransformed austenite of manganese steels is virtually nonmagnetic. The surface skin of castings may be somewhat magnetic; this is not detrimental in castings for wear-resistant service. B4.2 Thermal Conductivity. The thermal conductivity of manganese steels is about 25% of mild steel at room temperature, and continues to be substantially less at higher temperatures. This contributes to localized heat buildup during welding. B4.3 Thermal Expansion. The thermal expansion of manganese steels is similar to that of most other austenitic materials and greater than that of ferritic steels. The change in length on heating is about 1-1/2 times that of carbon steel.
B6. Welding Electrodes

B6.1 Austenitic Manganese Electrodes. Electrodes may be in the form of solid wire, tubular wire with internal alloying and fluxing ingredients, cut-to-length tubular electrodes with or without external covering, and covered electrodes with part or all of the alloys in the covering. Austenitic manganese steel electrodes are available as continuous wire and as bare or covered electrodes for manual welding. In the past, drawn, solid manganese steel electrodes, bare or with a light coating, were used extensively for the buildup of worn castings. They had the advantage of fast burn-off, high efficiency, and high bead buildup. On the adverse side, usability was relatively poor, requiring highly skilled welders to produce deposits free from porosity, inclusions, and cracking. As the electrodes were produced from large heats of steel the number of compositions available was very limited and phosphorus levels depended upon the capability of the producing mill. B6.2 Composite Electrodes. Bare manganese electrodes largely have been replaced by composite electrodes with alloys in the covering. Weldability is good and sound welds are obtained readily with normal procedures. Phosphorus content can be held consistently below 0.030%, greatly lessening the likelihood of weld cracking. Several compositions are available, alloyed with additions of nickel, molybdenum, chromium, and vanadium, alone or in combinations. A range of deposit properties is available, providing choices for different application requirements. For example, yield strength matching that of the base metal might be specified for fabrication or crack repair. Higher yield strength with better resistance to deformation might be specified for buildup of a worn railway crossing. B6.3 Tubular Electrodes. Bare tubular wire electrodes, used for track maintenance, are designed to weld without external shielding gas. As for composite electrodes, the
B5. Mechanical Properties

B5.1 Tensile and Yield Strengths. The properties of cast manganese steels vary considerably with composition, section thickness, and grain size. For the grade used for trackwork, typical properties are as follows: Tensile strength Yield strength Elongation, % Hardness 100 000 psi145 000 psi (690 MPa1000 MPa) 50 000 psi57 000 psi (345 MPa393 MPa) 30%65% 185 Brinell210 Brinell
B5.2 Impact Characteristics. Austenitic manganese steels have excellent impact properties, as measured by Charpy V-notch impact tests. For unalloyed manganese steels of the type used for trackwork, the impact strength is about 90 ft-lb100 ft-lb (122136 J) at 75F (24C) and about 45 ft-lb65 ft-lb (61 J88 J) at 100F (73C). These values confirm the outstanding toughness manganese steels provide in service under extremely cold conditions.
--`,,``,``,`,``,```,```,,````,`-`-`,,`,,`,`,,`---
22
AWS D15.2:2003
phosphorus content is kept low. The resultant welds have excellent mechanical properties and resistance to cracking. A number of variations in composition are available. B6.4 Other Austenitic Electrodes. In addition to austenitic manganese steel electrodes, other austenitic compositions can be used for welding austenitic manganese steel. For wear applications, the most commonly used are relatively high-carbon chromium-nickel-manganese and chromium-manganese alloys. These alloys often are more costly than austenitic manganese steel electrodes. Performance advantages in certain applications may more than offset differences in initial cost.
B7. Welding Procedures

Work hardened manganese steels are more susceptible to cracking when welded than unhardened metal. For that reason, work hardened metal, cracks, and other defects
should be removed prior to the start of welding. Grinding, air-carbon-arc gouging, or exothermic metal removal processes should be used. Care should be taken not to overheat the base metal during gouging; therefore, oxyfuel gas cutting is not recommended due to excessive heat input. Under normal conditions, preheat is not used. In extremely cold weather, the parts may be warmed to approximately 70F (20C). Welding procedures are intended to prevent the buildup of excessive heat in localized areas, and the consequent embrittlement of the base metal under the weld. Current, voltage, and travel speed should be such as to deposit relatively narrow rounded beads; large or very wide beads should be avoided. Skip welding should be used to minimize heat buildup, and can be effectively utilized on most worn castings. The temperature approximately 1 in. (25 mm) from the weld should be maintained below 500F (260C). As a rule of thumb, it should be possible to touch the base metal six inches from the weld without discomfort.
23
--`,,``,``,`,``,```,```,,````,`-`-`,,`,,`,`,,`---
--`,,``,``,`,``,```,```,,````,`-`-`,,`,,`,`,,`---
AWS D15.2:2003
Annex C Flash Welding Guidance

(This Annex is not a part of AWS D15.2-2003, Recommended Practices for the Welding of Rails and Related Components for Use by Rail Vehicles, but is included for informational purposes only.)
C1. Primary Welding Current

The primary welding current furnished to welding transformer shall be recorded. The following must be observed: C1.1 Total electrical energy (heat input) should match the standard certified record. C1.2 Loss of current flow for more than 3 cycles (50 ms) during the last half inch of burn-off flashing before upset stroke shall be cause for weld rejection and cut out. C1.3 Current flow must continue at least one half second after upset stroke starts or weld shall be rejected.
C2.3 The hold time should be consistent with the standard to prevent hot tears and hold alignment.
C3. Force Between Rail Ends

The force between rail ends, as measured through welding cylinders, is an optional recording. The following can be determined: C3.1 The total force to make the weld should approximately match the standard. C3.2 A minimum force, as determined by qualified personnel, should be executed between rail ends during the upset stroke.
C2. Platen Position

The platen position (relationship of fixed and moving rail) shall be recorded. The following must be observed: C2.1 Total rail consumed to make weld should match standard certified record with tolerances of +1/2 in. (+13 mm) and -1/8 in. (3 mm). C2.2 Upset stroke should consume (Forge) the same, or greater, amount of rail as consumed in the standard. Velocity, or upstroke, should be consistent with the standard certified record.
C4. Recordings
Recordings should be reported on the chart, beginning and end of each shift, and the heat numbers of all rails noted. Also, environmental factors such as temperature, wind, weather, etc., should be recorded on beginning of each chart. Operator should sign chart at end of day or chart shift.
--`,,``,``,`,``,```,```,,````,`-`-`,,`,,`,`,,`---
25
--`,,``,``,`,``,```,```,,````,`-`-`,,`,,`,`,,`---
AWS D15.2:2003
Annex D AREMA Tests for Continuous Welded Rail

--`,,``,``,`,``,```,```,,````,`-`-`,,`,,`,`,,`---
D1. Rolling Load Test

D1.1 The rolling load test basically is a full-scale fatigue test that produces measurable stress. Welded specimens then can be evaluated on a comparative basis. D1.2 Test Equipment. Figure D1 shows the typical load arrangement used for a 12 in. (300 mm) stroke test machine. D1.2.1 The weld, Figure D1, is located 2 in. (50 mm) in front of the front support providing a 10 in. (250 mm) moment arm. The wheel travels over the front support to 10 in. (250 mm) past the weld, stressing the longitudinal fibers of welded rail from 0 to maximum stress. D1.2.2 Wheel load may be varied by adjusting the load spring in accordance with Table D1. D1.2.3 Normal test is 60 cycles per minute for a total 2 million cycles or to failure, whichever occurs first.
Table D1 Wheel Loads for Rolling Load Test

Weight of Rail Section Pounds/ Yard 80 85 90 100 112 115 119 122 130 131 132 133 136 140 Kilograms/ Meter 39.7 42.2 44.6 49.6 55.6 57.0 59.0 60.5 64.5 65.0 65.5 66.0 67.5 69.4 Wheel Loads Pounds 29 500 32 300 35 000 40 200 46 600 48 200 50 300 52 000 56 200 56 700 57 300 58 700 59 400 61 300 Kilograms 13 380 14 650 15 880 18 230 21 140 21 860 22 820 22 590 25 490 25 720 25 990 26 630 26 940 27 810
D2. Slow Bend Test

D2.1 Welded assembly is placed head up on a four point loading fixture, Figure D2, with the base supports 48 in. (1200 mm) apart. The fixture is designed so that the one support is stationary and the other support swivels to eliminate torsional loading that might result in uneven bearing between the rail base and the support. D2.2 Load is applied to the rail head at two loading points spaced 12 in. (300 mm) apart. D2.3 Load is applied to the welded assembly in the center of the fixture until the assembly fractures or deflects 4 in. (100 mm), whichever comes first.
27
AWS D15.2:2003
SI EQUIVALENTS in. 2 3 10 12 14 19 27 mm 50 75 250 300 350 475 675
Figure D1Loading Arrangement for the 12 in. Stroke Rolling Load Machine
--`,,``,``,`,``,```,```,,````,`-`-`,,`,,`,`,,`---
28
AWS D15.2:2003
SI EQUIVALENTS in. 6 18 48 mm 150 450 1200
Figure D2Load Arrangement for the Slow Bend Test and Formula for Deriving the Modulus of Rupture
29
--`,,``,``,`,``,```,```,,````,`-`-`,,`,,`,`,,`---
--`,,``,``,`,``,```,```,,````,`-`-`,,`,,`,`,,`---
AWS D15.2:2003
--`,,``,``,`,``,```,```,,````,`-`-`,,`,,`,`,,`---
Annex E Safe Practices

These recommended practices may involve hazardous materials, operations, and equipment. The document does not purport to address all of the safety problems associated with their use. It is the responsibility of the user to establish appropriate safety and health practices. The user should determine any regulatory limits prior to use.
E1. Railroad Workplace Safety

Working on or about railroad tracks or property can present certain concerns for personal safety. Minimum Federal safety standards for the railroad workplace safety exist to prevent accidents and casualties to employees or individuals involved in certain railroad inspection, maintenance and construction activities. While performing work on or about existing railroad right of way, all personnel shall comply with workplace safety as defined by CFR Title 49, Part 214, Railroad Workplace Safety.
More detailed information on fumes and gases produced by the various welding processes may be found in the following: (1) The permissible exposure limits required by OSHA can be found in CFR Title 29, Chapter XVII Part 1910. The OSHA General Industry Standards are available from the Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402. (2) Material Safety Data Sheets (MSDS) are available upon request from suppliers for product safety and health information. (3) The results of an AWS-funded study are available in a report entitled, Fumes and Gases in the Welding Environment, available from the American Welding Society. (4) Safety and Health Fact Sheets, 3rd Edition 2003 available from AWS. AWS documents are available from Global Engineering, 15 Inverness Way East, Englewood, CO 80112-5776, Telephone (800) 854-7179, Fax (303) 307-2740, Internet www.global.ihs.com.
E3. Electrical Hazards E2. Fumes and Gases

Many welding, cutting, and allied processes produce fumes and gases which may be harmful to health. Fumes are solid particles which originate from welding filler metals and fluxes, the base metal, and any coatings present on the base metal. Gases are produced during the welding process or may be produced by the effects of process radiation on the surrounding environment. Management, personnel, and welders alike should be aware of the effects of these fumes and gases. The amount and composition of these fumes and gases depend upon the composition of the filler metal and base metal, welding process, current level, arc length, and other factors. Electric shock can kill. However, it can be avoided. Live electrical parts should not be touched. The manufacturers instructions and recommended safe practices should be read and understood. Faulty installation, improper grounding, and incorrect operation and maintenance of electrical equipment are all sources of danger. All electrical equipment and the workpieces should be grounded. The workpiece lead is not a ground lead. It is used only to complete the welding circuit. A separate connection is required to ground the workpiece. The workpiece should not be mistaken for a ground connection. The correct cable size should be used since sustained overloading will cause cable failure and result in possible electrical shock or fire hazard. All electrical connections
31
AWS D15.2:2003
should be tight, clean, and dry. Poor connections can overheat and even melt. Further, they can produce dangerous arcs and sparks. Water, grease, or dirt should not be allowed to accumulate on plugs, sockets, or electrical units. Moisture can conduct electricity. To prevent shock, the work area, equipment, and clothing should be kept dry at all times. Welders should wear dry gloves and rubber soled shoes, or stand on a dry board or insulated platform. Cables and connections should be kept in good condition. Improper or worn electrical connections may create conditions that could cause electrical shock or short circuits. Worn, damaged, or bare cables should not be used. Open circuit voltage should be avoided. When several welders are working with arcs of different polarities, or when a number of alternating current machines are being used, the open circuit voltages can be additive. The added voltages increase the severity of the shock hazard. In case of electric shock, the power should be turned OFF. If the rescuer must resort to pulling the victim from the live contact, nonconducting materials should be used. If the victim is not breathing, cardiopulmonary resuscitation (CPR) should be administered as soon as contact with the electrical source is broken. A physician should be called and CPR continued until breathing has been restored, or until a physician has arrived. Electrical burns are treated as thermal burns; that is, clean, cold (iced) compresses should be applied. Contamination should be avoided; the area should be covered with a clean, dry dressing; and the patient should be transported to medical assistance. Recognized safety standards such as ANSI Z49.1, Safety in Welding, Cutting, and Allied Processes, and the National Electrical Code and NFPA No. 70, available from National Fire Protection Association, Batterymarch Park, Quincy, MA 02269, should be followed.
E5. Burn Protection

Molten metal, sparks, slag, and hot work surfaces are produced by welding, cutting, and allied processes. These can cause burns if precautionary measures are not used. Workers should wear protective clothing made of fire-resistant material. Pant cuffs, open pockets, or other places on clothing that can catch and retain molten metal or sparks should not be worn. High-top shoes or leather leggings and fire-resistant gloves should be worn. Pant legs should be worn over the outside of high-top shoes. Helmets or hand shields that provide protection for the face, neck, and ears, and a head covering to protect the head should be used. In addition, appropriate eye protection should be used. When welding overhead or in confined spaces, ear plugs to prevent weld spatter from entering the ear canal should be worn in combination with goggles or equivalent to give added eye protection. Clothing should be kept free of grease and oil. Combustible materials should not be carried in pockets. If any combustible substance has been spilled on clothing, a change to clean, fireresistant clothing should be made before working with open arcs or flame. Aprons, cape-sleeves, leggings, and
E4. Noise
Excessive noise is a known health hazard. Exposure to excessive noise can cause a loss of hearing. This loss of hearing can be either full or partial, and temporary or permanent. In welding, cutting, and allied operations, noise may result from the process, the power source, or other equipment. Air-carbon arc and plasma arc are examples of processes, which are frequently noisy. Engines of engine-driven generators may also be quite noisy. Excessive noise adversely affects hearing capability. This adverse effect in hearing capability may be a temporary threshold shift from which the ears may recover if removed from the noise source. However, if a person is exposed to this same noise level for a longer time, then the loss of hearing may become permanent. The time re-
32
--`,,``,``,`,``,```,```,,````,`-`-`,,`,,`,`,,`---
quired to develop permanent hearing loss depends upon factors such as individual susceptibility, noise level, and exposure duration. In addition, there is evidence that excessive noise affects other bodily functions and behavior. A direct method to protect against excessive noise is to reduce the intensity of the source. Another method is to shield the source, but this has limitations. The acoustical characteristics of a room will also effect the level of noise. When engineering control methods fail to reduce the noise, personal protective devices such as ear muffs or ear plugs may be employed. Generally, these devices are only accepted when engineering controls are not fully effective. The permissible noise exposure limits can be found in CFR Title 29, Chapter XVII, Part 1910. This is available from the U.S. Government Printing Office, Washington, DC 20402. Additional information may be found in Threshold Limit Values for Chemical Substances and Physical Agents in the Workroom Environment, published by the American Conference of Governmental Industrial Hygienists, 6500 Glenway Avenue, Bldg. D-5, and Cincinnati, OH 45211. A recommended method for measuring noise emitted by arc welding processes may be found in the latest edition of AWS F6.1, Method for Sound Level Measurement of Manual Arc Welding and Cutting Processes, published by American Welding Society, 550 N.W. LeJeune Road, Miami, FL 33126.
AWS D15.2:2003
shoulder covers with bibs designed for welding service should be used. Where welding or cutting of unusually thick base metal is involved, sheet metal shields should be used for extra protection. Mechanization of highly hazardous processes or jobs should be considered. Other personnel in the work area should be protected by the use of noncombustible screens or by the use of appropriate protection as described in the previous paragraph. Before leaving a work area, hot work pieces should be marked to alert other persons of this hazard. No attempt should be made to repair or disconnect electrical equipment when it is under load. Disconnection under load produces arcing of the contacts and may cause burns or shock, or both. (Note: Burns can be caused by touching hot equipment such as electrode holders, tips, and nozzles. Therefore, insulated gloves should be worn when these items are handled, unless an adequate cooling period has been allowed before touching.) The following sources are for more detailed information on personal protection: (1) ANSI Z49.1, Safety in Welding, Cutting, and Allied Processes, published by the American Welding Society, 550 N.W. LeJeune Road, Miami, FL 33126. (2) Code of Federal Regulations, Title 29 Labor, Chapter XVII, Part 1910, OSHA General Industry Standards available from the U.S. Government Printing Office, Washington, DC 20402. (3) ANSI Z41.1, Safety-Toe Footwear, American National Standards Institute, 1430 Broadway, New York, NY 10018.
parameters, electrode and base metal composition, fluxes, and any coating or plating on the base material. E6.2 Some processes such as resistance welding and cold pressure welding ordinarily produce negligible quantities of radiant energy. However, most arc welding and cutting processes (except submerged arc when used properly), laser welding and torch welding, cutting, brazing, or soldering can produce quantities of non-ionizing radiation such that precautionary measures are necessary. Protection from possible harmful effects caused by nonionizing radiant energy from welding include the following measures: E6.2.1 Welding arcs should not be viewed except through welding filter plates which meet the requirements of ANSI Z87.1, Practice for Occupational and Educational Eye and Face Protection, published by American National Standards Institute, 1430 Broadway, New York, NY 10018. It should be noted that transparent welding curtains are not intended as welding filter plates, but rather are intended to protect a passerby from incidental exposure. E6.2.2 Exposed skin should be protected with adequate gloves and clothing as specified in ANSI Z49.1, Safety in Welding, Cutting, and Allied Processes, published by American Welding Society, 550 N.W. LeJeune Road, Miami, FL 33126. E6.2.3 Reflections from welding arcs should be avoided, and all personnel should be protected from intense reflections. (Note: Paints using pigments of substantially zinc oxide or titanium dioxide have a lower reflectance for ultraviolet radiation.) E6.2.4 Screens, curtains, or adequate distance from aisles, walkways, etc., should be used to avoid exposing passersby to welding operations. E6.2.5 Safety glasses with UV protective side shields have been shown to provide some beneficial protection from ultraviolet radiation produced by welding arcs. Ionizing radiation information sources include: (1) AWS F2.1-78, Recommended Safe Practices for Electron Beam Welding and Cutting, available from the American Welding Society, 550 N.W. LeJeune Road, Miami, FL 33126. (2) Manufacturers product information literature. Non-ionizing radiation information sources include: (1) J. F. Hinrichs, Project committee on radiationsummary report. Welding Journal, January 1978. (2) Non-Ionizing Radiation Protection Special Study No. 42-0053-77, Evaluation of the Potential Hazards from Actinic Ultraviolet Radiation Generated by Electric Welding and Cutting Arcs, available from the National
E6. Radiation
E6.1 Welding, cutting, and allied operations may produce radiant energy (radiation) harmful to health. One should become acquainted with the effects of this radiant energy. Radiant energy may be ionizing (such as X-rays), or non-ionizing (such as ultraviolet, visible light, or infrared). Radiation can produce a variety of effects such as skin burns and eye damage, depending on the radiant energys wavelength and intensity, if excessive exposure occurs. E6.1.1 Ionizing Radiation. Ionizing radiation is produced by the electron beam welding process. It is ordinarily controlled within acceptance limits by use of suitable shielding enclosing the welding area. E6.1.2 Non-Ionizing Radiation. The intensity and wavelengths of non-ionizing radiant energy produced depend on many factors, such as the process, welding
--`,,``,``,`,``,```,```,,````,`-`-`,,`,,`,`,,`---
33
AWS D15.2:2003
Technical Information Service, Springfield, VA 33161. ADA-033768. (3) Non-Ionizing Radiation Protection Special Study No. 42-0312-77, Evaluation of the Potential Retina Hazards from Optical Radiation Generated by Electrical Welding and Cutting Arcs, available from the National Technical Information Service, Springfield, VA 22161. ADA-043023. (4) C. E. Moss and W. E. Murray, Optical Radiation Levels Produced in Gas Welding, Torch Brazing, and Oxygen Cutting, Welding Journal, September 1979. (5) Optical Radiation Levels Produced by Air-Carbon Arc Cutting Processes, Welding Journal, March 1980.
(6) Z136.1, Safe Use of Lasers, published by American National Standards Institute, 1430 Broadway, New York, NY 10018. (7) ANSI Z49.1, Safety in Welding, Cutting, and Allied Processes, published by the American Welding Society, 550 N.W. LeJeune Road, Miami, FL 33126. (8) ANSI Z87.1, Practice for Occupational and Educational Eye and Face Protection, published by American National Standards Institute, 1430 Broadway, New York, NY 10018. (9) C. E. Moss, Optical Radiation Transmission Levels Through Transparent Welding Curtains, Welding Journal, March 1979.
34
--`,,``,``,`,``,```,```,,````,`-`-`,,`,,`,`,,`---
AWS D15.2:2003
Annex F Guidelines for Preparation of Technical Inquiries for AWS Technical Committees
(This Annex is not a part of AWS D15.2:2003, Recommended Practices for the Welding of Rails and Related Rail Components for Use by Rail Vehicles, but is included for informational purposes only.)
F1. Introduction
The AWS Board of Directors has adopted a policy whereby all official interpretations of AWS standards will be handled in a formal manner. Under that policy, all interpretations are made by the committee that is responsible for the standard. Official communication concerning an interpretation is through the AWS staff member who works with that committee. The policy requires that all requests for an interpretation be submitted in writing. Such requests will be handled as expeditiously as possible but due to the complexity of the work and the procedures that must be followed, some interpretations may require considerable time.
--`,,``,``,`,``,```,```,,````,`-`-`,,`,,`,`,,`---
with the edition of the standard that contains the provisions or that the inquirer is addressing. F2.2 Purpose of the Inquiry. The purpose of the inquiry must be stated in this portion of the inquiry. The purpose can be either to obtain an interpretation of a standard requirement, or to request the revision of a particular provision in the standard. F2.3 Content of the Inquiry. The inquiry should be concise, yet complete, to enable the committee to quickly and fully understand the point of the inquiry. Sketches should be used when appropriate and all paragraphs, figures, and tables (or the Annex), which bear on the inquiry must be cited. If the point of the inquiry is to obtain a revision of the standard, the inquiry must provide technical justification for that revision. F2.4 Proposed Reply. The inquirer should, as a proposed reply, state an interpretation of the provision that is the point of the inquiry, or the wording for a proposed revision, if that is what inquirer seeks.
F2. Procedure
All inquiries must be directed to: Managing Director, Technical Services American Welding Society 550 N.W. LeJeune Road Miami, FL 33126 All inquiries must contain the name, address, and affiliation of the inquirer, and they must provide enough information for the committee to fully understand the point of concern in the inquiry. Where that point is not clearly defined, the inquiry will be returned for clarification. For efficient handling, all inquiries should be typewritten and should also be in the format used here. F2.1 Scope. Each inquiry must address one single provision of the standard, unless the point of the inquiry involves two or more interrelated provisions. That provision must be identified in the scope of the inquiry, along
F3. Interpretation of Provisions of the Standard

Interpretations of provisions of the standard are made by the relevant AWS Technical Committee. The secretary of the committee refers all inquiries to the chairman of the particular subcommittee that has jurisdiction over the portion of the standard addressed by the inquiry. The subcommittee reviews the inquiry and the proposed reply to determine what the response to the inquiry should be. Following the subcommittees development of the response, the inquiry and the response are presented to the entire committee for review and approval. Upon
35
AWS D15.2:2003
approval by the committee, the interpretation will be an official interpretation of the Society, and the secretary will transmit the response to the inquirer and to the Welding Journal for publication.
only through a written request. The Headquarters staff can not provide consulting services. The staff can, however, refer a caller to any of those consultants whose names are on file at AWS Headquarters.
F4. Publication of Interpretations

All official interpretations will appear in the Welding Journal.
F6. The AWS Technical Committee

The activities of AWS Technical Committees in regard to interpretations, are limited strictly to the interpretation of provisions of standards prepared by the committee or to consideration of revisions to existing provisions on the basis of new data or technology. Neither the committee nor the staff is in a position to offer interpretive or consulting services on: (1) specific engineering problems, or (2) requirements of standards applied to fabrications outside the scope of the document or points not specifically covered by the standard. In such cases, the inquirer should seek assistance from a competent engineer experienced in the particular field of interest.
F5. Telephone Inquiries

Telephone inquiries to AWS Headquarters concerning AWS standards should be limited to questions of a general nature or to matters directly related to the use of the standard. The Board of Directors policy requires that all AWS staff members respond to a telephone request for an official interpretation of any AWS standard with the information that such an interpretation can be obtained
36
--`,,``,``,`,``,```,```,,````,`-`-`,,`,,`,`,,`---
AWS D15.2:2003
List of AWS Documents on Railroad Welding

Designation D15.1 Title Railroad Welding SpecificationCars and Locomotives
For ordering information, contact Global Engineering Documents, an Information Handling Services (IHS) Group company, 15 Inverness Way East, Englewood, Colorado 80112-5776; telephones: (800) 854-7179, (303) 397-7956; fax (303) 397-2740; Internet: www.global.ihs.com.
37
--`,,``,``,`,``,```,```,,````,`-`-`,,`,,`,`,,`---
--`,,``,``,`,``,```,```,,````,`-`-`,,`,,`,`,,`---

Aws D15.2

Uploaded by

Copyright:

Available Formats

Aws D15.2

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Aws D15.2

Uploaded by

Copyright:

Available Formats

AWS D15.

2:2003 An American National Standard

Licensee=ConocoPhillips WAN/5919206100 Not for Resale, 03/31/2005 06:06:31 MST

Key Words Arc welding processes, crossings,

550 N.W. LeJeune Road, Miami, Florida 33126

Statement on Use of AWS American National Standards

Licensee=ConocoPhillips WAN/5919206100 Not for Resale, 03/31/2005 06:06:31 MST

This page is intentionally blank.

Licensee=ConocoPhillips WAN/5919206100 Not for Resale, 03/31/2005 06:06:31 MST

This page is intentionally blank.

Licensee=ConocoPhillips WAN/5919206100 Not for Resale, 03/31/2005 06:06:31 MST

3. Rail, Rail Components Manufactured from Rail, and Their Repair

Component Material Carbon steel

Table 1 Processes for Carbon and Alloy Steel Rail Components

Figure 1Typical Weld Pattern for Rail End Repair

4. Repair or Fabrication of Components Manufactured from Austenitic Manganese Steel

5. Recommended Practices for Joining of Rails by Thermite Welding (TW)

Cycles 2 000 000

Specification 3575 6.350 mm (0.25 in.) maximum deviation

6. Flash Welding (FW) of Rail

7. General Procedure Qualification Arc Welding Processes

8. Track Welder QualificationArc Welding Processes

SI EQUIVALENTS in. 1/8 1/4 mm 3 6

Figure 3Layout of Hardness Survey on Rail Head

SI EQUIVALENTS in. 1/4 5/8 mm 6 16

Figure 4Layout of Transverse Hardness Survey

Form 1 Typical Welding Procedure Qualification Test Record

ULTRASONIC EXAMINATION UT Report No. _________________________________

METALLOGRAPHY Macroetch Size 1.________________ 2. ___________ Microetch detail ________________________________

Form 2 Typical Welder Qualification Test Record

Licensee=ConocoPhillips WAN/5919206100 Not for Resale, 03/31/2005 06:06:31 MST

Annex A Welding Processes

A1. Arc Welding

A3. Flash Welding (FW)

A4. Oxyfuel Gas Welding (OFW)

A2. Thermite Welding (TW)

Figure A1Shielded Metal Arc Welding (SMAW)

Figure A2Gas Metal Arc Welding (GMAW)

Figure A3Flux Cored Arc Welding (FCAW)

Licensee=ConocoPhillips WAN/5919206100 Not for Resale, 03/31/2005 06:06:31 MST

Figure A4Section Through a Thermite Mold and Crucible

Figure A6Rail Welding Production Line

Figure A7Oxyfuel Gas Welding (OFW)

This page is intentionally blank.

Licensee=ConocoPhillips WAN/5919206100 Not for Resale, 03/31/2005 06:06:31 MST

Annex B Welding of Austenitic Manganese Steel

B3. Basic Metallurgy

B4. Physical Properties

B6. Welding Electrodes

B5. Mechanical Properties

B7. Welding Procedures

This page is intentionally blank.

Licensee=ConocoPhillips WAN/5919206100 Not for Resale, 03/31/2005 06:06:31 MST

Annex C Flash Welding Guidance

C1. Primary Welding Current

C3. Force Between Rail Ends

C2. Platen Position

This page is intentionally blank.

Licensee=ConocoPhillips WAN/5919206100 Not for Resale, 03/31/2005 06:06:31 MST

METALLOGRAPHY Macroetch Size 1.__________ 2. _ Microetch detail ____________________________