4-1

Con iguration o Glycol Pump is a trademark o Kimray, nc

Product Selection Guide

Glycol Pumps

Glycol Pumps
Dehydrator

Dry gas out Dry Glycol

Reboiler Absorber (Contactor)

Wet gas in

Wet Glycol Pump Dry Glycol Heat Exchanger Surge Tank

Wet Glycol

4-2

Natural Gas
Wet natural gas enters the bottom of the absorber. It flows upward through a packed bed or through a series of bubble cap or valve trays filled with glycol where thorough contact is made. The gas gives up water vapor to the glycol as it passes upward and leaves the absorber as dry gas ready to enter the sales line.

Glycol Pump
The Glycol Pump takes glycol at absorber pressure, moves it into the reboiler at atmospheric pressure, and then returns it to pressure adequate to drive the glycol back into the abosrber. All this is accomplished by utilizing some of the gas at absorber pressure to drive the system without an additional source of outside energy. The Glycol Pump operates in various demanding conditions: high temperature, high pressure, varied chemical contaminates, and potential of a wide range of abrasive materials. Nearly 50 years of demanding service have proven the ruggedness and dependability of the unique and robust design.

Glycol
The dry concentrated glycol is continuously pumped to the top tray of the absorber. As the glycol moves downward from tray to tray it absorbs the water vapor from the rising gas stream. The wet glycol is then removed at the bottom of the absorber and pumped through a large preheating coil in the surge tank. It then enters the still column at the top of the reboiler where the water vapor is stripped away as steam. The regenerated glycol spills down into the surge tank and is pumped to the top of the absorber to start another cycle.

Glycol Pumps

Function:
Circulates glycol in a dehydration system. Circulates amine in a desulphurizer system. Utilizes the energy of gas and glycol at absorber pressure as its source of power.

Features:
No auxiliary power required Eliminates need for level control and dump valve at absorber Low gas consumption Completely sealed system prevents glycol loss Only two moving assemblies Hydraulic cushioned check valves with removable seats of hardened stainless steel Circulation Rates: SC Series 8 - 200 gph PV Series 3 - 450 gph

High Pressure
Model Number 315 PV 1715 PV 4015 PV 9015 PV 21015 PV 45015 PV Capacity Gallons / Hour Minimum Maximum 3 13 8 40 12 40 27 90 66 210 166 450

PV
Working Pressure Minimum Maximum 100 1500 300 1500 300 1500 300 1500 400 1500 400 1500

Working Pressure: 1500 psig Options:

Elastomers: HSN, Viton, Aflas Metal Materials: 316 Stainless Steel, 17-4 PH Stainless Steel

Low Pressure (Small Cylinder)

Model Number 2015 SC 5015 SC 10015 SC 20015 SC Capacity Gallons / Hour Minimum Maximum 8 20 12 50 22 100 60 200

SC
Working Pressure Minimum Maximum 100 500 100 500 100 500 100 500

Features:
Sock type element In line filter removal 1/4 NPT Bleed Valve connection Hammer union cap Solid mount 3/4 NPT inlet and outlet connections

4-3

Temperature Range: -20 to 650oF Working Pressure: 1500 psig Recommended Pumps:
315PV 4015PV 9015PV 2015SC 5015SC

Glycol Filter Canister

Used to filter particles of rust, sludge and debris from the glycol lines before the glycol reaches the pumping system. This allows the glycol pump to operate more freely and reduces pump wear. The filter itself is disposable and can easily be replaced.

Con iguration o Glycol Pump is a trademark o Kimray, nc

Dehydration Equipment
Liquid Level Control

Universal Level Control

ULC

GEN II Liquid Level Controller

Original Side Mount GEN II

Features:
Direct acting Intermittent bleed pilot Simple installation Easy to use No adjustment required .65 specific gravity or higher

Bodies Available:
1 NPT Brass, Steel, or Stainless Steel 2 NPT Steel or Stainless Steel

Maximum W.P.: 1500 psig Supply Pressure: 30 psig max. Maximum Temperature: 200 F
o

GEN II Back Mount

Options:

4-4

Low density, high temperature float Vertical float adapter Supply Pressure: 0-35 psig maximum Vessel Operating Pressure: 50 to 4000 psig maximum Temperature Range: -20 to 200oF Optional elastomers provide higher maximum temperature Float Travel:3/4 maximum

Features:
Compact Design: installs inside a smaller turning space than brand F or N Low Friction Waggle Arm: no rotating stuffing box and related friction/stiction Snap or Throttle control in one pilot: simple adjustment to change from snap to throttle control with the turn of a knob. Intermittent-Bleed pilot meets BMP in the EPA Natural Gas Star Program. Built-in 40 micron supply gas filter Vibration Tough 1/4 NPT Tapped Vented Pilot: Easy to connect and pipe exhaust away if needed. Vertical or Horizontal Displacer: field configurable standards specified

Other Kimray dehydration equipment:

Liquid Level Controls Dump Valves Thermostats Burner Valves Pressure Regulators

THERES A LOT MORE TO GAS DEHYDRATION THAN THE KIMRAY GLYCOL PUMP!

Dehydration Equipment
Dump Valves and Burner Valves
Normal Service: Liquids Features:
Quick opening trim Travel indicator Available in Pressure Opening or Pressure Closing Field reversible actuator Teflon packed stuffing box requires no lubrication Open yoke design - accurate travel indication - complete isolation of actuator

High Pressure Motor Valve

Angle or Thru valve body Carbide trim Ideal for high pressure differential On / Off service Valve Connection 1 2 Available Orifice Sizes 1/8, 3/16, 1/4, 3/8 1/4, 3/8, 1/2, 3/4, 1

Construction Materials:
Valve Body Stem Plug Cage Actuator Seat Diaphragms High Pressure Motor Valve Steel 303 Stainless 303 Stainless Steel Ductile Iron Steel Nitrile/Nylon Non-Freeze High Pressure Dump Steel 303 Stainless Carbide Steel Ductile Iron D2 Steel or Carbide Nitrile/Nylon

Con iguration o High Pressure Motor Valve is a trademark o Kimray, nc

Non-Freeze High Pressure Dump Valve

The Non-Freeze Dump Valve places the trim inside the vessel in direct contact with the process liquid, preventing freezing within the valve. Valve Carbide Connection 1 Inlet & Outlet 2 Vessel Mounting Available Orifice Sizes 1/4, 3/8, 1/2

High Pressure Motor ValveSizes available:

1 NPT, Flanged - Angle or Through Body 2 NPT, Flanged - Angle or Through Body

SMS

Non-Freeze Motor Valve Size available:

1 NPT Inlet & Outlet 2 Vessel Mounting

Standard actuator has an effective diaphragm area of 30 square inches. 65 Topworks has an effective area of 65 square inches, which allows a wider adjustable spring range. Maximum Pressure Drop:

Maximum Working Pressure: 4000 psi Temperature Range: -20o to 200o F Options:
Elastomers: HSN, Viton, Aflas Trim Material: Stainless Steel, Carbide

4-5

65 SMS

SMS - 1/4 - 2000 psi 3/8 - 800 psi 1/2 - 450 psi 65 SMS - 1/4, 3/8, 1/2 - 4000 psi

Normal Service: Liquids Features:

Equal Percentage trim Soft seat for bubble tight shut-off Special stem seal requires no lubrication

Spring Closing Pressure Opening

SMT DAB

Pressure opening Burner Valve used where a reduced inner valve is desired and manifold pressures do not exceed 25 psig.

Construction Materials:
Body Design Pressure Stem Plug Seat Cast Iron Scrd. 175 psi Flgd. 175 psi 303 Stainless Ductile Iron Nitrile Ductile Iron Scrd. 300 psi Flgd. 250 psi 303 Stainless Ductile Iron Polyurethane Nitrile/Nylon Steel Flgd. 285 psi 303 Stainless Steel Polyurethane Nitrile/Nylon

Adjustable Pressure Opening

SMT ADA

Diaphragms Nitrile/Nylon

Pressure opening Burner Valve for throttling or snap action service and where manifold pressures do not exceed 40 psig.

Sizes available:
1 NPT 2 NPT, Flanged

Temperature Range: -20o to 200o F Options:

Elastomers: HSN, Viton, Aflas Trim Material: 316 Stainless Steel internal parts Orifice Size: LIne size or reduced

THERES A LOT MORE TO GAS DEHYDRATION THAN THE KIMRAY GLYCOL PUMP!

Dehydration Equipment
Thermostats & Supply Gas Regulator

Thermostat Features:
Single adjustment High accuracy Intermittent-bleed construction Bi-metalic sensing element

Indirect Throttle Thermostat

T 12

Indirect control of burner valves, mixing valves, air shutters

Supply Pressure: 5 to 30 psig Working Pressure (sensing element):

500 psig without Separable Socket 4000 psig with Separtable Socket 7000 psig with Special Separable Socket Separable socket is an extra price item and is ordered separately.

Indirect High Temperature Shut-Down

T 12M

Temperature Range:
T 12, T 18 HT 12, HT 18 Pilot Guard -30o to 400o F -34o to 204o C -30o to 750o F -34o to 399o C -30o to 2100o F -34o to 1149o C

For temperature controlled system shutdown until manually reset Shuts off when system temperature exceeds setpoint

Options:
Elastomers: HSN, Viton, Aflas Metal Material: 316 Stainless Steel internal exposed parts

Pilot Guard

HT12 PG
Indirect action for system shut-down when pilot flame goes out. Also used in direct mode for high stack temperture shutdown

Indirect Acting Thermostats:

4-6

Output decreases with temperature rise.

Supply Gas Regulator Features:

Easily adjusted Internally relieving Available in Aluminum and 316 Stainless Steel

Supply Gas Regulator

SGR

Connections:
Inlet and Outlet - 1/4 NPT

Maintains constant downstream pressure.

Provides a supply of constant reduced pressure for pneumatic instruments and pilot operated controllers.

Operating Temperature:
0o to 200oF (-18oC to 93oC)

Maximum Inlet Pressure:

4000 psi

Outlet Pressure:
0 to 125 psi

Construction Materials:
Body: Aluminum or 316 Stainless Steel Diaphragm: Polyurethane Seat: Nylon

THERES A LOT MORE TO GAS DEHYDRATION THAN THE KIMRAY GLYCOL PUMP!