Single Phase Controlled

Single Phase Controlled Rectifier with Cosine Firing Scheme ST2709
Operating Manual Ver.1.1
An ISO 9001 : 2000 company
94-101, Electronic Complex Pardesipura, Indore- 452010, INDIA Tel : 91-731- 2570301/02, 4211100 Fax: 91- 731- 2555643 E-mail : info@scientech.bz Website : www.scientech.bz Toll free No. : 1800-103-5050
ST2709
Scientech Technologies Pvt. Ltd.
ST2709
Single Phase Controlled Rectifier with Cosine Firing Scheme ST2709 Table of Contents 1. 2. 3. 4. 5. Introduction Features Technical Specifications Theory Experiments Experiment 1 Study of cosine firing scheme for single-phase converter Experiment 2 Study of half wave controlled rectifier with resistive load. Experiment 3 Study of full wave controlled rectifier (mid- point configuration) with resistive load. Experiment 4 Study of half controlled bridge rectifier (common cathode configuration) with R load. Experiment 5 Study of half controlled bridge rectifier (common anode configuration) with resistive load. Experiment 6 Study of half controlled bridge rectifier (asymmetrical configuration) with resistive load. Experiment 7 Study of fully controlled bridge rectifier with resistive load 4 5 6 7 14 17 20
23
26
29
6. 7. 8.
32 35 38 38
Data Sheet Warranty List of Accessories
ST2709
Introduction Single Phase Controlled Rectifier with Cosine Firing Scheme ST2709 is a compact, ready to use power electronics experiment board. Cosine firing circuit is available on this board. This board is helpful for students to know how to generate firing pulses for single phase converter using cosine firing scheme. Synchronized sine signal convert into cosine signal using integrator and generate firing pulses in the cosine firing scheme. Different experiments can be performed by making connections using patch cords. List of Boards : Model Name PE01 UJT Characteristics PE02 MOSFET Characteristics PE03 SCR Characteristics PE04 TRIAC Characteristics PE05 DIAC Characteristics PE06 IGBT Characteristics PE07 PUT Characteristics PE10 SCR Triggering (R, RC Full wave, RC Half wave) PE11 SCR Triggering (UJT) PE12 SCR Triggering (IC555) PE13 SCR Triggering (IC74121) PE14 Ramp and Pedestal triggering PE15 SCR Triggering (IC741) PE16 SCR Triggering (PUT) PE40 SCR Lamp Flasher PE41 SCR Alarm Circuit PE42 Series Inverter PE43 UJT Relaxation oscillator List of other Boards available are : Model Name ST2701 IGBT Characteristics ST2702 SCR Triggering (R, RC Half wave, RC Full wave) ST2703 SCR Triggering Techniques ST2704 Triggering of SCR using 74121 IC ST2705 SCR Lamp Flasher ST2706 SCR Alarm Circuit ST2707 Series Inverter ST2708 Single Phase Controlled Rectifier (With Ramp Comparator Firing Scheme) and many more
Scientech Technologies Pvt. Ltd. 4
ST2709
Features Built in power supply. Easy to operate and understand. Two firing circuits on single board. Gradual firing angle control up to 180 degree. Test points provided to check outputs at different blocks. Sockets to make different connections. On board AC sources of 15V and 18V. On board rectifier components and load. Pulse Transformer provided for isolation.
RoHS Compliance
Scientech Products are RoHS Complied. RoHS Directive concerns with the restrictive use of Hazardous substances (Pb, Cd, Cr, Hg, Br compounds) in electric and electronic equipments. Scientech products are Lead Free and Environment Friendly. It is mandatory that service engineers use lead free solder wire and use the soldering irons upto (25 W) that reach a temperature of 450C at the tip as the melting temperature of the unleaded solder is higher than the leaded solder.
ST2709
Technical Specifications Power Supply Power Consumption On board AC source On Board Firing Circuits : : : : 230V 10%, 50Hz 3VA (approximately) 0V-15V, 18V-0V-18V. cosine firing scheme a. b. c. d. e. f. g. Interconnections SCR Assembly Pulse Transformer Fuse Load Test Points Dimensions (mm) Weight : : : : : : : : synchronized step down transformer integrator comparator 1& 2 inverter clock pulse generator 1&2 JK flip flop Pulse amplifier and pulse transformer
Different blocks of cosine scheme :
2mm sockets 4 SCRs 2P4M, 600V, 2A PT4502, 1:1 1A 1 K, 10 W 9 W 420 H 100 D 255 2 Kg approximately
ST2709
Theory Earlier, DC power was obtained from motor generator sets or AC power was converted to DC power by means of mercury arc rectifiers or thyratrons. The advent of thyristors has changed the art of AC to DC conversion. Presently, Phase controlled AC to DC converters employing thyristors are extensively used for changing constant AC input voltage to controlled DC output voltage. In industry where there is a provision for modernization, mercury-arc rectifiers and thyratrons are being replaced by thyristors. In phase controlled rectifiers, a thyristor is turned off as AC supply voltage reverse biases it, provided anode current has fallen to level below the holding current. The turning off, or commutation, of a thyristor by supply voltage itself is called natural commutation. As phase controlled rectifier need no commutation circuitry, these are simple, less expensive and are therefore widely used in industries where controlled DC power is required. Principle of phase control : The simplest form of controlled rectifier circuits consist of a single thyristor feeding DC power to a resistive load R. The source voltage is Vs = Vm sin t. An SCR can conduct only when anode voltage is positive and a gating is applied. As such, a thyristor blocks the flow of load current Io until it is triggered. At some delay angle !, a positive gate signal applied between gate and cathode turns on the SCR, Immediately, full supply voltage is applied to the load as Vo. At the instant of delay angle !, Vo rises from zero to Vm sin ! as shown in figure for resistive load, current io is in phase with Vo. Firing angle of thyristor is measured from the instant it would start conducting if it were replaced by diode. If thyristor is replaced by diode, it would begin conduction at t = 0,2", 4" etc.; firing angle is therefore measured from these instants. A firing angle may thus be defined, as the angle between the instant thyristor would conduct if it were a diode and the instant it is triggered. It is also defined as the angle measured from the instant that gives the largest average output voltage to the instant it is triggered. Once the SCR is On, load current flows, until it is turned-off by reversal of voltage at t= ", 3", 5" etc. load current falls to zero and soon after the supply voltage reverse biases the SCR , the device is therefore, turn off. By varying the firing angle !, the phase relationship between the start of the load current and the supply voltage can be controlled. Phase Controlled Rectifier : There are two types of rectifier; 1. 2. Half wave rectifier Full wave rectifier
ST2709
Half Wave Controlled Rectifier : Single-phase half wave controlled rectifier means that the single SCR is used to convert the AC to DC During the positive half cycle of the input voltage, thyristor T1 is forward biased and current flows through the load when the thyristor is fired, at t = !. The thyristor conducts only when the anode is positive with respect to cathode and a positive gate signal is applied, otherwise, it remains in the forward blocking state and blocks the flow of the load current.
Figure 1 In the negative half cycle, i.e., at t = ", the thyristor is in the reverse biased condition and no current flows through the load. Thus, varying the firing angle at which the thyristor starts conducting in positive half controls the average DC output voltage cycle. The waveforms of the above circuit are shown in figure the output load voltage and current is positive, i.e., they are one quadrant; it is called a half wave semi converter. The average DC output voltage across load is given by VDC = Em (1+cos !)/2" ..(1) And VDC (maximum) = Em/" Average current is given by IDC = Em (1 + cos !)/2"R ..(2) And, the DC output power is PDC = VDC X IDC .(3)
ST2709
Full Wave Rectifier : There are two types of full rectifier; 1. 2. Mid-point configuration Bridge configuration
Mid-Point Full Wave Rectifier : The circuit diagram of a single-phase full-wave converter using center-tapped transformer is shown in figure when terminal P of the transformer is positive w.r.t. to terminal Q in the positive half cycle of the supply, and if thyristor T1 is fired at t = !, current flows from terminal P through thyristor T1, the load resistance R and back to the center tapped of the transformer. This current continues to flow up to 180#and when the input voltage changes its polarity, the thyristor T1 goes from the On-state to the Off-state. In the negative half cycle, when terminal Q is positive w.r.t. Terminal P, if thyristor T2 is fired at t = (" +!), current flows through the thyristor T2, the load resistance and back to the center tapped of the transformer. This current continues to flow up to 2" when the thyristor T2 turns Off. Thus, there are two current pulses of the same direction across the load in one complete cycle. Since thyristor T1 and T2 are forward biased during the positive and negative half cycles respectively.
(A)
(B)
Figure 2
ST2709
The average DC voltage across load is VDC = Em (1+cos !)/" The average load current is IDC = Em (1+cos !)/"R Therefore, the DC output power is PDC = VDC X IDC Bridge Type Full Wave Rectifier : There are two types of bridge configuration full wave rectifier : 1. 2. Fully controlled bridge rectifier Half controlled bridge rectifier ..(5) ..(4)
Fully Controlled Bridge Rectifier : A single-phase fully controlled bridge circuit with resistive load consists of four thyristor as shown in figure. During the positive half cycle when terminal P is positive w.r.t.Q, thyristors T1 and T2 are in the forward blocking state and when these thyristors fire simultaneously at t = !, the load is connected to the input through T1 and T2. During negative half cycle i.e., after t = ", thyristor T3 and T4 are in the forward blocking state, and simultaneous firing of these thyristors reverse biases the previously conducting thyristors T1 and T2. These reverse biased thyristors turn off due to line or natural commutation and the load current transfers from T1 and T2 to T3 and T4. The voltage and current waveforms are shown in figure.
Fully-controlled bridge circuit with resistive-load
10
ST2709
Waveform for fully-controlled bridge with resistive-load
Figure 3 The average DC voltage across load is VDC = Em (1+cos !)/" The average load current is IDC = Em (1+cos !)/"R Therefore, the DC output power is PDC = VDC X IDC .. (7) (6)
11
ST2709
Half Controlled Bridge Rectifier : In these configurations two thyristors are replaced by power diodes and can be connected in either arm of the bridge. Depending on the connections, these are further classified as 1. 2. 1. 2. Symmetrical Asymmetrical Common cathode Common anode
Symmetrical configuration is in two types
Out of these configurations, the common cathode symmetrical configuration is the most commonly used configuration, because a single trigger can be used to fire both thyristors without any electrically isolation. During the positive half cycle, when Pis more positive w.r.t. Q and when thyristor T1 is triggered, the load currents flows through T1 and the diode D2 in the circuit shown in figure during the negative half cycle, when Q is more positive w.r.t. P, the thyristor T2 and the diode D1 constitute the load current. The waveforms of the voltage and current in relation to the input voltage are shown in figure.
(a)
(b)
(c) Figure 4
Where, figure (a) is common cathode, (b) is common anode and (c) is asymmetrical configuration Average DC voltage across load is VDC = Em (1+ cos !) / " And average current is IDC = Em (1+ cos !) / "R Average power is PDC = VDC X IDC .(8) (9)
12
ST2709
Single Phase Converter Firing Circuit : There are many schemes to generate firing pulses for single phase rectifier Cosinefiring scheme in which synchronized sinusoidal signal is converted in cosine wave. Cosine Firing Scheme : This scheme used to fire thyristors in single phase converter. The pulse output of this scheme synchronizes with AC supply using step down transformer supply voltage step down to an appropriate level. Input to this transformer taken from same source from which converter circuit is energized. The output voltage of transformer is integrated using integrator to get cosine wave V1. The cosine signal compare with reference voltage in comparator 1 and in comparator 2 compare with invert of reference voltage. The DC control voltage EC varies from maximum positive Ecm to maximum negative Ecm so that firing angle can be varied from 0 to 180 degree. So the comparator 1 and comparator 2 give output pulses V2 and V3. The firing angle is governed by the intersection of V1 and EC. When EC is a maximum, firing angle is zero. Thus firing angle ! in terms of V2m and Ec can be expressed as V2m cos! = EC Or ! = cos-1 (E C /V 2m) Where V 2m = maximum value of cosine signal V 2. The signals V 3, V4 obtained from comparators are fed to clock pulse generators 1, 2 to get clock pulses V5, V6. These signals V5, V6 energies a JK flip flop to generate output signals Vi and Vj. the signal Vi is amplified through the amplifier circuit and then employed to turn On the SCRs in the positive half cycle. Signals Vj, after amplification, is used to trigger SCRs in the negative half cycle. Firing angle in time is ! = (180 X T) / 10ms So, T = (! X 10ms) / 180 Where, time T in ms And, VRMS = VM /$2 Then, VM = $2 X VRMS . (13) . (12) ... (11) (10)
13
ST2709
Experiment 1 Objective : Study of cosine firing circuit for single-phase converter Equipments Needed : 1. 2. 3. Power Electronics board, ST2709 Oscilloscope ST201 or equivalent 2 mm patch cords.
Circuit diagram : The basic cosine firing circuit block diagram is shown in the below figure 5
Figure 5
ST2709
Procedure : 1. 2. 3. 4. 5. 6. Make sure that there should not be any connections by patch cord on the board. Rotate the firing control Potentiometer 1 in fully clock wise direction and Potentiometer 2 in fully counter clockwise direction. Switch On the power supply. Observe the sine wave AC signal between 15V and 0V and note readings of amplitude and time. Observe the output waveforms of integrator point 1w.r.t. ground and note readings of amplitude and time base. Observe the output waveforms of comparator1, comparator 2 at points 2and 3 w.r.t ground and also note readings of amplitude and time base. Observe the output waveforms of clock pulse generator 1, clock pulse generator 2 at points 4and 5w.r.t. ground and also note readings of amplitude and time base. Observe the output waveforms of gate pulse 1 gate pulse 2 points 6and 7w.r.t. ground and also note readings of amplitude and time base. Plot the waveforms of input signal, cosine signal, comparator1 and comparator 2 outputs, clock pulse1 and 2, gate pulse 1 and 2.
7. 8.
15
ST2709
S. No. output Output

A T A T A T A T A T A T
Input signal Output
Cosine signal
Comparator 1
Comparator 2
Clock pulse Clock Pulse 1 2 output
Gate pulse 1
Gate pulse 2

A T
16
ST2709
Experiment 2 Objective : Study of half wave controlled rectifier with resistive load Equipments Needed : 1. 2. 3. 4. Power Electronics board, ST2709 Oscilloscope ST201 or equivalent 2 mm patch cords. Multimeter, ST4022 or equivalent
Circuit diagram : The circuit diagram of basic half wave controlled rectifier is shown in the below figure 6
Figure 6
17
ST2709
Procedure : 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Make sure that there should not be any connections by patch cord on the board Rotate the firing control Potentiometers 1 and 2 in full counter clockwise direction and also switch set at Potentiometer 1 side. Switch On the power supply Measure the AC voltage (Vrms) by voltmeter between point 0V-15V and calculate Em by Em =1.414 X Vrms. Switch Off the power. Connect the circuit of half wave rectifier as shown figure 6 using 2 mm patch cords. Switch On the power supply Connect the Oscilloscope and voltmeter across the load. Vary the firing control Potentiometer and set on 30, 60, 90, 120 and 150 firing angles using equation (11). Observe the output waveforms and note the readings of voltage across load on different firing angles. Observe the waveform across the SCR1 when firing angle is 90. Calculate the average load current IDC and power PDC from measured load voltage Vo. Plot the input signal, gate pulse, and drop signal across SCR and output waveforms when firing angle is 90.
18
ST2709
Observation Table :
S. No. In (Vm) VDC / RL In Deg. In Time (ms) Measured Voltage (Vo) Calculated Voltage (VDC) Measured (Io) Vo / RL Calculated (IDC)
Input AC Voltage Measure d Po Vo X Io
Firing Angle
Average Output Voltage Across Load
Average Load Current (IDC)
Average Output Power Calculate d (PDC) VDC X IDC
In (Vrms)
19
ST2709
Experiment 3 Objective : To study the full wave controlled rectifier (mid-point configuration) with resistive load. Equipments Needed : 1. 2. 3. 4. Power Electronics board, ST2709 Oscilloscope ST201 or equivalent 2 mm patch cords. Multimeter ST4022 or equivalent
Circuit diagram : The circuit diagram of basic full wave controlled rectifier (mid- point configuration) is shown in the below figure 7
Figure 7
20
ST2709
Procedure : 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Make sure that there should not be any connections by patch cord on the board Rotate the firing control Potentiometer in full clockwise direction. Switch On the power supply Measure the AC voltage (Vrms) by voltmeter between point 0V-18V and calculate Em by Em =1.414 X Vrms. Switch Off the power. Connect the circuit of full wave controlled rectifier (mid-point configuration) as shown figure 7 using 2 mm patch cords. Switch On the power supply Connect the Oscilloscope and voltmeter across the load. Vary the firing control Potentiometer and set on 30, 60, 90, 120 and 150 firing angles using equation (11). Observe the output waveforms and note the readings of voltage across load on different firing angle. Connect the Oscilloscope one by one across SCR1 and SCR2 and observe the waveform when firing angle is 90. Calculate the average load IDC current and power PDC from measured load voltage Vo. Plot the input signal, gate pulse, and drop signal across SCR and output waveforms when firing angle is 90.
21
ST2709
Observation Table :
Firing Angle
S.No In (Vm) VDC / RL In Deg. In Time (ms) Measured Voltage (Vo) Calculated Voltage (VDC) Measured (Io) Vo / RL Calculated (IDC)
In (Vrms)
22
ST2709
Experiment 4 Objective : Study of half controlled bridge rectifier (common cathode configuration) with resistive load Equipments Needed : 1. 2. 3. 4. Power Electronics board, ST2709 Oscilloscope ST210 or equivalent 2 mm patch cords. Multimeter ST4022 or equivalent
Circuit diagram : The circuit diagram of basic half controlled bridge rectifier (common cathode configuration) is shown in the below figure 8
Figure 8
23
ST2709
Procedure : 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Make sure that there should not be any connections by patch cord on the board. Rotate the firing control Potentiometer in full clockwise direction. Switch On the power supply Measure the AC voltage (Vrms) by voltmeter between point 0V-15V and calculate Em by Em =1.414 X Vrms. Switch Off the power supply Connect the circuit of half controlled bridge rectifier (common cathode configuration) as shown figure 8 using 2 mm patch cords. Switch On the power supply Connect the Oscilloscope and voltmeter across the load. Vary the firing control Potentiometer and set on 30, 60, 90, 120 and 150 firing angles using equation (11). Observe the output waveforms and note the readings of voltage across load on different firing angle. Connect the Oscilloscope one by one across SCR1 and SCR2 and observe the waveform when firing angle is 90. Calculate the average load IDC current and power PDC from measured load voltage Vo. Plot the input signal, gate pulse, and drop signal across SCR and output waveforms when firing angle is 90.
24
ST2709
Observation Table :
Input AC Voltage
Firing Angle
Average Output Power Measure d Po Vo X Io Calculate d (PDC) VDC X IDC
In (Vrms)
25
ST2709
Experiment 5 Objective : Study of half controlled bridge rectifier (common anode configuration) with resistive load Equipments Needed : 1. 2. 3. 4. Power Electronics board, ST2709 Oscilloscope ST201 or equivalent 2 mm patch cords Multimeter ST4022 or equivalent
Circuit diagram : The circuit diagram of basic half controlled bridge rectifier (common anode configuration) is shown in the below figure 9
Figure 9
26
ST2709
Procedure : 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Make sure that there should not be any connections by patch cord on the board Rotate the firing control Potentiometer in full clockwise direction. Switch On the power supply Measure the AC voltage (Vrms) by voltmeter between point 0V-15V and calculate Em by Em =1.414 X Vrms. Switch Off the power supply Connect the circuit of half controlled bridge rectifier (common anode configuration) as shown figure 9 using 2 mm patch cords. Switch On the power supply Connect the Oscilloscope and voltmeter across the load. Vary the firing control Potentiometer and set on 30, 60, 90, 120and 150 firing angles using equation (11). Observe the output waveforms and note the readings of voltage across load on different firing angle. Connect the Oscilloscope one by one across SCR1 and SCR2 and observe the waveform when firing angle is 90. Calculate the average load IDC current and power PDC from measured load voltage Vo. Plot the input signal, gate pulse, and drop signal across SCR and output waveforms when firing angle is 90.
27
ST2709
Observation Table :
Firing Angle
In (Vrms)
28
ST2709
Experiment 6 Objective : Study of half controlled bridge rectifier (asymmetrical configuration) with resistive load Equipments Needed : 1. 2. 3. 4. Power Electronics board, ST2709 Oscilloscope ST201 or equivalent 2 mm patch cords. Multimeter ST4022 or equivalent
Circuit diagram : The circuit diagram of basic half controlled bridge rectifier (asymmetrical configuration) is shown in the below figure 10
Figure 10
29
ST2709
Procedure : 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Make sure that there should not be any connections by patch cord on the board Rotate the firing control Potentiometer in full clockwise direction. Switch On the power supply Measure the AC voltage (Vrms) by voltmeter between point 0V-15V and calculate Em by Em =1.414 X Vrms. Switch Off the power supply Connect the circuit of half controlled bridge rectifier (asymmetrical configuration) as shown figure 10 using 2 mm patch cords. Switch On the power supply Connect the Oscilloscope and voltmeter across the load. Vary the firing control Potentiometer and set on 30, 60, 90, 120 and 150 firing angles using equation (11). Observe the output waveforms and note the readings of voltage across load on different firing angle. Connect the Oscilloscope one by one across SCR1 and SCR2 and observe the waveform when firing angle is 90. Calculate the average load IDC current and power PDC from measured load voltage Vo. Plot the input signal, gate pulse, and drop signal across SCR and output waveforms when firing angle is 90.
30
ST2709
Observation Table : Firing Angle Average Output Voltage Across Load Measured Voltage (Vo) VDC / RL Calculated Voltage (VDC) Measured (Io) Vo / RL Calculated (IDC) Measure d Po Vo X Io Average Load Current (IDC) Average Output Power Calculate d (PDC) VDC X IDC
S. No. In (Vm) In Deg. In Time (ms)
Input AC Voltage
In (Vrms)
31
ST2709
Experiment 7 Objective : Study of fully controlled bridge rectifier with resistive load Equipments Needed : 1. 2. 3. 4. Power Electronics board, ST2709 Oscilloscope ST201 or equivalent 2 mm patch cords. Multimeter ST4022 or equivalent
Circuit diagram : The circuit diagram of basic fully controlled bridge rectifier is shown in the below figure 11
Figure 11
32
ST2709
Procedure : 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Make sure that there should not be any connections by patch cord on the board. Rotate the firing control Potentiometer in full clockwise direction. Switch On the power supply Measure the AC voltage (Vrms) by voltmeter between point 0V-15V and calculate Em by Em =1.414 X Vrms. Switch Off the power supply Connect the circuit of fully-controlled bridge rectifier as shown figure 11 using 2 mm patch cords. Switch On the power supply Connect the Oscilloscope and voltmeter across the load. Vary the firing control Potentiometer and set on 30, 60, 90, 120 and 150 firing angles using equation (11). Observe the output waveforms and note the readings of voltage across load on different firing angle. Connect the Oscilloscope one by one across SCR1, SCR2, and SCR3 & SCR4 and observe the waveform when firing angle is 90 respectively. Calculate the average load IDC current and power PDC from measured load voltage Vo. Plot the input signal, gate pulse, and drop signal across SCR and output waveforms when firing angle is 90.
33
ST2709
Observation Table :
Firing Angle
Average Output Power
In (Vrms)
Calculated (PDC) VDC X IDC
34
ST2709
Data Sheet
35
ST2709
36
ST2709
37
ST2709
1.
Warranty We guarantee the we guarantee the product against all manufacturing defects for 24 months from the date of sale by us or through our dealers. Consumables like dry cell etc. are not covered under warranty. The guarantee will become void, if a) b) c) d) The product is not operated as per the instruction given in the operating manual. The agreed payment terms and other conditions of sale are not followed. The customer resells the instrument to another party. Any attempt is made to service and modify the instrument.
2.
3.
The non-working of the product is to be communicated to us immediately giving full details of the complaints and defects noticed specifically mentioning the type, serial number of the product and date of purchase etc. The repair work will be carried out, provided the product is dispatched securely packed and insured. The transportation charges shall be borne by the customer.
4.
List of Accessories 1. 2. 3. 4. 5. 2mm Patch Cord (Red) 16 ...................................................................... 6 Nos. 2mm Patch Cord (Black) 16.................................................................... 6 Nos. 2mm Patch Cord (Blue) 16 ..................................................................... 6 Nos. Mains Cord ................................................................................................1 No. e-Manual....................................................................................................1 No.
38
ST2709
List of other Trainers available from us are : Model Name PE01 UJT Characteristics PE02 MOSFET Characteristics PE03 SCR Characteristics PE04 TRIAC Characteristics PE05 DIAC Characteristics PE06 IGBT Characteristics PE07 PUT Characteristics PE10 SCR Triggering (R, RC Full wave, RC Half wave) PE11 SCR Triggering (UJT) PE12 SCR Triggering (IC555) PE13 SCR Triggering (IC74121) PE14 Ramp and Pedestal Triggering PE15 SCR Triggering (IC741) PE16 SCR Triggering (PUT) PE40 SCR Lamp Flasher PE41 SCR Alarm Circuit PE42 Series Inverter PE43 UJT Relaxation Oscillator PE44 Single Phase PWM Inverter ST2701 IGBT Characteristics ST2702 SCR Triggering (R, RC Half wave, RC Full wave) ST2703 SCR Triggering Techniques ST2704 Triggering of SCR using 74121 IC ST2705 SCR Lamp Flasher ST2706 SCR Alarm Circuit ST2707 Series Inverter ST2708 Single Phase Controlled Rectifier (with Ramp Comparator Firing Scheme) ST2709 Single Phase Controlled Rectifier (Cosine Firing Scheme) ST2710 Single Phase Converter Firing Techniques (by TCA 785IC and Triangular Comparator) ST2711 Lamp Dimmer ST2712 Electronics Power Lab ST2713 Single Phase Cyclo-Converter ST2714 Speed Control of Universal Motor using SCR ST2715 Speed Control of AC Motor using TRIAC ST2716 Microcontroller Based Firing Circuit for Controlled Rectifier ST2717 SCR Commutation Circuits ST2718 Bedford & Parallel Inverter ST2719 Step-Up Chopper ST2720 Single Phase Bridge Inverter ST2722 Step-Down Chopper ST2723 AC Chopper
39

Single Phase Controlled

Uploaded by

Copyright:

Available Formats

Single Phase Controlled

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Single Phase Controlled

Uploaded by

Copyright:

Available Formats

Single Phase Controlled Rectifier with Cosine Firing Scheme ST2709

Operating Manual Ver.1.1

An ISO 9001 : 2000 company

Scientech Technologies Pvt. Ltd.

Data Sheet Warranty List of Accessories

Scientech Technologies Pvt. Ltd.

Scientech Technologies Pvt. Ltd.

Different blocks of cosine scheme :

Scientech Technologies Pvt. Ltd.

Scientech Technologies Pvt. Ltd.

Fully-controlled bridge circuit with resistive-load

Scientech Technologies Pvt. Ltd.

Waveform for fully-controlled bridge with resistive-load

Scientech Technologies Pvt. Ltd.

Symmetrical configuration is in two types

Scientech Technologies Pvt. Ltd.

Scientech Technologies Pvt. Ltd.

Scientech Technologies Pvt. Ltd.

S. No. output Output

Input signal Output

Clock pulse Clock Pulse 1 2 output

Scientech Technologies Pvt. Ltd.

Scientech Technologies Pvt. Ltd.

Scientech Technologies Pvt. Ltd.

Input AC Voltage Measure d Po Vo X Io

Average Output Voltage Across Load

Average Load Current (IDC)

Average Output Power Calculate d (PDC) VDC X IDC

Scientech Technologies Pvt. Ltd.

Scientech Technologies Pvt. Ltd.

Scientech Technologies Pvt. Ltd.

Input AC Voltage Measure d Po Vo X Io

Average Output Voltage Across Load

Average Load Current (IDC)

Average Output Power Calculate d (PDC) VDC X IDC

Scientech Technologies Pvt. Ltd.

Scientech Technologies Pvt. Ltd.

Scientech Technologies Pvt. Ltd.

Scientech Technologies Pvt. Ltd.

Average Output Voltage Across Load

Average Load Current (IDC)

Average Output Power Measure d Po Vo X Io Calculate d (PDC) VDC X IDC

Scientech Technologies Pvt. Ltd.

Scientech Technologies Pvt. Ltd.

Input AC Voltage Measure d Po Vo X Io

Average Output Voltage Across Load

Average Load Current (IDC)

Average Output Power Calculate d (PDC) VDC X IDC

Scientech Technologies Pvt. Ltd.

Scientech Technologies Pvt. Ltd.

Scientech Technologies Pvt. Ltd.

S. No. In (Vm) In Deg. In Time (ms)

Scientech Technologies Pvt. Ltd.

Scientech Technologies Pvt. Ltd.

Scientech Technologies Pvt. Ltd.

Input AC Voltage Measure d Po Vo X Io

Average Output Voltage Across Load

Average Load Current (IDC)

Average Output Power