Bulk Solids Handling
Bulk Solids Handling
Bulk Solids Handling
Bulk Solids Handling: Equipment Selection and Operation Edited by Don McGlinchey
© 2008 Blackwell Publishing Ltd. ISBN: 978-1-405-15825-1
i
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls December 21, 2007 21:32
Edited by
Don McGlinchey
Reader
Centre for Industrial Bulk Solids Handling
Glasgow Caledonian University
UK
iii
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls December 21, 2007 21:32
c 2008 by Blackwell Publishing Ltd
The right of the Author to be identified as the Author of this Work has been asserted in accordance with the
Copyright, Designs and Patents Act 1988.
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronic, mechanical, photocopying, recording or otherwise, except as permitted by
the UK Copyright, Designs and Patents Act 1988, without the prior permission of the publisher.
Designations used by companies to distinguish their products are often claimed as trademarks. All brand names
and product names used in this book are trade names, service marks, trademarks or registered trademarks of their
respective owners. The publisher is not associated with any product or vendor mentioned in this book.
This publication is designed to provide accurate and authoritative information in regard to the subject matter
covered. It is sold on the understanding that the publisher is not engaged in rendering professional services. If
professional advice or other expert assistance is required, the services of a competent professional should be
sought.
ISBN: 978-1-4051-5825-1
A catalogue record for this title is available from the British Library
The publisher’s policy is to use permanent paper from mills that operate a sustainable forestry policy, and which
has been manufactured from pulp processed using acid-free and elementary chlorine-free practices. Furthermore,
the publisher ensures that the text paper and cover board used have met acceptable environmental accreditation
standards.
iv
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls December 21, 2007 21:32
Contents
Contributors xi
Aims and Scope xii
Acknowledgements xiii
v
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls December 21, 2007 21:32
vi CONTENTS
2 Hopper/bin design 68
JOHN W. CARSON
2.1 Fundamentals 68
2.2 Flow patterns 69
2.3 Arching 74
2.4 Ratholing 76
2.5 Flow rate 76
2.6 Segregation 78
2.6.1 Sifting 78
2.6.2 Dusting (particle entrainment) 79
2.6.3 Fluidisation (air entrainment) 79
2.7 Importance of outlet and outlet region 79
2.8 Aerated versus non-aerated 82
2.9 Selection criteria 82
2.9.1 How to set bin size 82
2.9.2 Flow pattern selection 85
2.9.3 Inlets and outlets 85
2.9.4 Inserts 89
2.9.5 Cylinder geometry 91
2.9.6 Materials of construction 92
2.9.7 Type of feeder and valve 93
2.9.8 Safety and environmental considerations 93
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls December 21, 2007 21:32
CONTENTS vii
viii CONTENTS
CONTENTS ix
x CONTENTS
Index 287
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls December 21, 2007 21:32
Contributors
xi
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls December 21, 2007 21:32
The readership is expected to be engineers, scientists and technologist, most likely process
operators and chemical engineers or mechanical engineers or physicists. They may be
young engineers or ‘role changers’ with little formal education in bulk solids handling who
have responsibility for handling, storage, processing or production involving particulate
materials.
The topics covered by the book will include the characterisation of individual particles and
bulk particulate materials, silo design for strength and flow, pneumatic conveying systems,
mechanical conveying, small-scale operations. Belt conveying will not be covered in this
volume.
The material in the book will provide an overview and discuss the limitations and applica-
tions of the technology. Guidance will be given on making appropriate equipment choices.
Operational issues will be discussed and will include example calculations and case studies.
The book aims to provide the reader with the breadth of knowledge to give a good general
understanding of the major technologies involved in the storage and handling of particulate
materials from large grains to fine cohesive materials. This will place the reader in a better
position of being able to diagnose solids handling and storage problems in industry and to
deal with experts and equipment suppliers from an informed standpoint.
The material contained in the book is designed to be equally applicable to engineers
and scientists working in a broad spectrum of industries, for example agriculture, agro-
chemicals, cement, construction, food, bulk and fine chemicals industries, minerals and
metals, petro-chemicals, pharmaceuticals, plastics, pigments, power generation and waste
handling.
xii
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls December 21, 2007 21:32
Acknowledgements
I wish to thank all the authors who made such significant contributions to this book. I thank
all at Wiley-Blackwell for their advice and help in bringing the book together. I would also
like to thank colleagues at Glasgow Caledonian University for their support and time.
xiii
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls December 21, 2007 21:17
1.1 Introduction
The success of powdered material process engineering and manufacturing is dependent upon
the measurement and control of micro-, nano- and bio-scale particulate products as well
as the behaviour of bulk powders on a macro-scale. Great strides have been accomplished
with on-line, in-line and in-process characterisation of micro-scale particles, but in order to
optimise the multivariate products generated nowadays, fundamental understanding must
be gained in bulk processing and product behaviour at all levels of the industrial scale.
Powders can be regarded as being either two- (solid–liquid) or three-phasic (solid–liquid–
gas) systems which, at times, can be treated as a single continuum. Because there is a great
variety in the bulk powder properties and characteristics of such assemblies there is a need
to understand the mechanico-physical properties of discrete solid particles as well as the
physico-chemical interaction of adsorbed solid–fluid boundaries on particles.
Thus, there is an awareness to regard the continuous fluid phase (generally a gas) not
only as a supportive phase, but also as a major contributing addition to the solid particulate
phase and to treat powders as a solid–fluid system.
Powders, in reality and practice, are not solely solid units of matter, which can withstand
shear and deformation under mild stress, but may, at times, also be regarded as liquids.
With a degree of applied stress powders can be encouraged to flow from hoppers and bins
and may, with excessive aeration, flood-like liquids. If desired these particulate systems can
also be compacted into coherent shapes such as granules, pellets or compacts. Although
powders can be packed tightly in packed beds and compressed into discrete forms they do
not behave as gases and have no gaseous-like properties.
There are many of empirical instruments which may measure bulk powder characteristics,
which affects the behaviour of powders in processing plants. And some of these empirical
laboratory instruments have now been commercialised. However, the sophistication of in-
strumentation available for the measurement of bulk powder properties in real time is not as
advanced as the instruments currently used to measure particle size on a micro- or nano-scale.
The phenomenon of flow of a powder out of any orifice or from a specified piece of process
plant equipment should be unambiguously termed ‘rate of powder flow’ and not confused
with the bulk powder property of flowability which can be used discriminate the ‘handabil-
ity’ of bulk powders and may eventually contribute to enhance the rate of powder flow.
The common definition of flowability is the ability of a powder to flow from a specific
item of plant equipment at a desired degree of flowability. Flowability is generally quantified
by a range of mobility, from ‘free flow’ to ‘non-flow’ which can, at times, be measured in a
laboratory with specific flow property instrumentation. A bulk powder may be described as
being free flowing, cohesive or non-flowing, and thus powder flowability tends to become an
integral part of the description of bulk powder property measurement. Correlations between
powder bulk properties in terms of both micro-scaled particulate factors as well as macro-
Bulk Solids Handling: Equipment Selection and Operation Edited by Don McGlinchey 1
© 2008 Blackwell Publishing Ltd. ISBN: 978-1-405-15825-1
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls December 21, 2007 21:17
Possible
problem areas
Adhesion
Moisture Sticking to surfaces
properties
content
Poor fluidisation
Cohesion Balling and sintering
Particle size
properties
and distribution
Poor dewatering
Hopper discharge
Wall friction Wall deposits
Conveyor buildup
Particle
shape Bulk flow
Paste flow in pipes
properties
Chemical
composition Abrasivity Machinery wear
Figure 1.1 Micro- and macro-scale properties of bulk powders allied to possible production problems.
scale bulk properties can therefore enhance and possibly optimise process engineering and
the handling of powders.
‘Bulk powder properties’ refer to the results from tests performed either under specified
laboratory conditions or with pilot plant equipment under known processing conditions.
With knowledge of the ‘bulk properties of a powder’, under specified conditions, problems
in the handling and flow of the multitude of powders currently produced may be highlighted
and hopefully corrected or alleviated. All too often powder handling problems experienced
in modern industrial chemical and pharmaceutical plants is due mainly to inadequate in-
formation associated with macro-scale powder bulk properties of real industrial powders
as opposed to idealised laboratory micro-scale particulate systems. This section will there-
fore itemise some of the available micro-particle and macro-powder properties that may
influence, and possible prevent, some inherent problems seen in the processing of industrial
powders (Figure 1.1).
To aid the process plant engineer, information must be available in terms of bulk powder
behaviour under specific conditions. Powders should therefore be treated as a biphasic
assembly and handled with knowledge of the interactions between a fluid and the solid
external and internal surfaces. In this way, powder behaviour can be visualised as behaving
in two separate manners either in terms of fluid-like behaviour or compacted solid-like
behaviour. Both of these conceptual viewpoints will be considered in this section, but the
emphasis will be on the fluid-like (flow) behaviour of powders.
Since in the physical world there are only three dimensions: mass, length and time; bulk
powder properties can only be described in terms of the inter-relationship between these
three dimensions.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls December 21, 2007 21:17
1.1.1 Density
The relationship between mass and volume is density and the determination of this basic
property is essential in the subsequent understanding of bulk powder behaviour.
1.1.4 Flowability
The largest category of bulk powder behaviour, expressed in the terms of the three-
dimensional parameters, is either a mass–time or a volume–time relationship. This category
measures the rate of discharge from orifices, as opposed to the bulk powder properties of
flowability and/or floodability of powders (Table 1.1).
Table 1.1 Categories of particle assemblies in terms of mass, length and time.
the distribution of other powder properties, as opposed to the physical size, shape and, at
times, the physico-chemical properties of particles, is difficult to achieve and analyse.
The properties and phenomena associated with an assembly of particles and powder
behaviour in processing are due to the combination of many individual particle and powder
properties, some of which are listed below:
This chapter will highlight the factors of packing (bulk density, voidage), rate of flow,
compressibility of packing, flowability, failure properties and angle of internal friction,
cohesion, strength and adhesion. The factors of particle size distribution, specific surface
area and particle shape distribution have already been dealt with elsewhere (Stanley-Wood
2000, 2005).
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls December 21, 2007 21:17
Particle
uniformity
Porosity
Particle density Vibration
Fluid phase
Figure 1.2 Micro-scale particle and macro-scale powder parameters contribution to bulk powder behaviour.
Penetration into the internal structure of porous material with a fluid to determine particle
density can result in ambiguous volume measurements. Thus, immersion methods have
minimal use unless specific conditions are defined.
In practice:
r Large pieces of porous material must be used
r The liquid immersion method is dependent upon penetration of liquid into pores
r Agglomeration of fine particles can occur with liquids
r The degree of penetration into particle pores varies with the liquid used, the surface
tension of the liquid as well as the pressure exerted
r Gas density displacement methods are limited to non-absorbable gases
r The impregnation or the coating of porous material to prevent liquid penetration is
limited to large particles and not applicable to fine material
The bulk density of a powder is its mass divided by the bulk volume it occupies. This
volume includes the inter-particle space between the particles as well as the particle volume
and should not be confused with the term particle volume, which does not include the
inter-particle space.
Bulk packed and poured densities are known to be dependent upon the rate of powder feed
when material is directed into a specific volume containment. Thus the rate of powder flow,
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls December 21, 2007 21:17
Table 1.2 A selection of densities from National and International Standards to show the multitude
of defined densities used in the process industries.
Bulk densities
Poured Aerated Cap loaded Unpacked
Tapped Sack loaded Bagged Vibrated
Weight/length ratio Pipe Weight per unit length
Geometric densities
Particle Powder Compact
Ergun Mercury Pill
Bulk Pellet Feed
Skeletal or internal porous structure
Adsorption Mercury
Surface area Permeability
height of fall, impact pressure and powder yield strength together with other physical powder
properties, such as particle size, particle shape, particle density and powder cohesiveness
contribute influentially to powder bulk density.
The range of terms used to describe the general property of the bulk density of a powder
is legion but can readily be subdivided into:
r Densities related to the bulk of the powder
r Densities related to the external geometry of the particles within a powder or
r Densities related to the internal geometry of particles within powders
Thus powder density as well as particle density may have many descriptions and definitions
(BS EN 1097-3: 1998; BS EN 543: 2003; BS EN 725-8: 1997; BS EN 993-17: 1999; ISO
6770: 1982) (Table 1.2).
The bulk density of a material is not therefore a single definite number like a true solid
density. Initially both particle and bulk densities were regarded as being easy to measure.
Particle density is now, however, regarded as a complex material property due to the exclu-
sion or inclusion of open and/or closed pore space within a solid mass or particle (Table 1.3).
The variety of particle densities is due to the variation in penetration of the displacement
fluid into a particle needed to record the volume of the porous particle when undergoing
measurement. Whilst the reason why the bulk density of a powder has no unique value is
because bulk densities vary as a function of the consolidation pressure applied to the powder
within the containing space and volume. It is thus essential to specify the degree of com-
paction on an assembly of particles contained in a specified volume before a measurement
value can be recorded (BS 2955: 1993; BS 4140-23: 1987; BS EN 23923-2: 1993; BS EN
ISO 7837: 2001; ASTM B329-98: 2003; ISO 3923-1:1979).
Although there is no direct linear relationship between the flow of a powder and its bulk
density, the bulk density, with its numerous variations in definition (Table 1.3), is important
because of bin or hopper capacity:
r Indication of the size of particles, which will either flood or pack together
r Determination of the compression strength of powders or compaction strength of
powders
r Classification of particles into fluidisable and non-fluidisable powders
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls December 21, 2007 21:17
Table 1.3 Glossary of terms used to define particle and powder densities.
Particle densities
Apparent particle density Mass of a particle divided by the volume of the particle excluding open pores
but still including the closed pores
The mass of a particle divided by its apparent volume
Apparent particle volume The total volume of the particle, excluding open pores, but including closed
pores
Effective particle density Mass of a particle divided by the volume of the particle including open pores
and closed pores
The density of particles as determined by a given fluid displacement method
Effective particle volume The mass of the particles divided by the effective particle density
Envelope volume The external volume of a particle, powder or monolith such as would be
obtained by tightly shrinking a film to contain it
True particle density Mass of a particle divided by the volume of the particle excluding open pores
and closed pores
Powder densities
Absolute powder density Mass of powder divided by the absolute powder volume
Absolute powder volume Space occupied by a powder excluding pores, interstices and voids
Absolute volume The volume of the solid matter after exclusion of all the spaces (pores and
voids)
Apparent powder density Mass of powder divided by the apparent volume
Apparent powder volume The total volume of solid matter, open pores and closed pores and interstices
Bulk powder density The apparent powder density under defined conditions
Effective solid density The density of powdered particles by a specified liquid displacement method
Green density Apparent density of a compact before sintering or other heat treatment
Pressed density Apparent density of a compact
Immersed density Mass of a powder expressed as a percentage volume of suspension media
displaced
Tap density Apparent powder density of a powder bed formed in a container of stated and
specified dimensions when subjected to vibration or tapping under known and
stated conditions
Aerated density Apparent powder density of a powder bed formed in a container of stated and
specified dimensions when subjected to minimum compression to ensure an
open loosely packed volume
Poured density Aerated bulk density; the minimum bulk density of a motionless powder
Pressed density The apparent density of a compact
Voids The space between particles in a bed of powder
Since powders can be regarded as a mixture of solid and fluid (usual air) the density for a
bulk powder can vary between that of the continuum (gas/fluid) and the solid phase. The
value of bulk density is thus dependent upon the packed state of the powder; and there may
be a range of densities for one powder:
all of which are dependent upon the history or treatment which the powdered sample has un-
dergone prior to bulk density measurement. Although each method can offer reproducibility
of measurement, these laboratory results may not mimic or represent the actual compaction
or stress which powders made undergo in process plant.
Results of the variation of bulk density with the degree of compaction, typically shown
as a log–log plot, can be beneficial in the determination of the type of plant equipment
required for transfer, storage and processing (Carson & Marinelli 1994) (see Section 1.3.5).
1.3.1.2 Carr’s aerated and packed bulk density box A square box with a bottomless
extension containing a coarse screen (10 mesh or 2 mm) positioned slightly up from the
bottom of the extension was constructed and assembled (Figure 1.4). Material is screened
into the known dimensioned bottom box. After removal of the extension and levelling of the
powder in the bottom box, the box is weighed. This weight times an appropriate numerical
factor gives the aerated bulk density (Carr 1965b).
The packed density is determined by replacement of the extension box onto the powder
filled aerated bottom box. Placement of more powder into the extension box, clamping the
two together and vibration for 5 minutes packs the powder into the bottom box. Exten-
sion removal, levelling of excess powder and weighing gives, with the appropriate factor,
the packed bulk density. This technique has now been incorporated into a standard test
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls December 21, 2007 21:17
(a) (b)
Hopper
Tapped bulk
Aerated bulk density
Cup extension
density piece
Screen cover
Standard
100 mL cup
Screen
Spacer ring
Vibrating chute
Screen
Stationary chute
Air-borne fines
Standard
100 mL cup
Pan positioning
piece
Figure 1.3 Hosokawa apparatus for aerated (a) and tapped (b) density.
3 in 11 in
48 4 14
100 mesh
3 in 1 in
42
1 in
42
Figure 1.4 Carr’s aerated and tap density box (Carr 1965c; ASTM D 6393-99: 1999).
9
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls December 21, 2007 21:17
method (ASTM D 6393-99: 1999) for bulk solid characterisation by Carr’s indices, and has
been applied to improve the flowability, handling and storage of distiller’s grains (Ileleji
2005).
1.3.2.1 Scott volumeter Since the definition of bulk density is related to the apparent
powder volume under defined conditions, the methodology outlined in ISO 3923-2 (1981)
and EN 23923 (1992) may be used to determine the bulk density of metals and other powders
using the Scott volumeter to give an ‘as poured’ bulk density.
1.3.3.1 Hall test cup method This standard test cup has a 25 mL volume with a 25 mL
extension volume. After the cup and extension have been filled and excess powder removed –
similar to the Hosokawa method – the sample is tapped for a given number of cycles
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls December 21, 2007 21:17
using a sieve shaker. The cup extension is removed after tapping has been completed, and
excess powder scraped off the upper surface of the cup. The standard cup, filled with a
known volume of powder, is removed and weighed to eventually give the tap bulk density.
Vibration of the cup and extension is not recommended because of low non-reproducible
results, although in one American Standard (ASTM D-4180-03) a vibrated funnel is used.
1.3.3.2 Kostelnik and Beddow Ro-Tap method A Ro-Tap method was used by Kostelnik
and Beddow (1970) for tap bulk densities and they proposed that when the aerated bulk
density was determined for subsequent use in the Hausner ratio (Section 1.4.1) the same
standard test cup should be used. Visual determination of the volume end point is difficult
and thus the weight end point methodology is preferable.
For particles in the range 0.8–4.8 mm, a 250 mL cylinder is recommended with mechanical
tapping. The tapping unit is marketed as a Tap-Pak Volumeter (J. Engelsmann Company).
Powder poured into this measuring cylinder is tapped 1000 times and the volume measured.
From the initial weight of powder a tapped bulk density can be determined.
Hausner ratio, in shape analysis, the behavioural effects in fluidisation, mixing and handling,
is a simple factor which is relatively easy to measure but which has been found to have
worthwhile industrial powder qualitative assurance potential.
It has been subsequently used to characterise the flow, sieving and compaction of powders
and many other aspects of powder technology for a diversity of industrial powders (Adler
1969; Kostelnik et al. 1968; Roberts & Beddow 1968; Woodcock & Mason 1987; Wong
2000).
The most complicated technique for the determination of powder flowability is that
proposed by Jenike (Section 1.6.1), in which the ratio of the maximum compaction stress,
σ , to an unconfined stress, f c , at a specified shear stress of 3 kPa – the flow function, ff – is
calculated to predict the ease of powder flow. This Jenike flow function, ff = σ1 / f c , has
remained the main consensual parameter designated for mass flow hopper design and the
flowability of powders.
Using the Jenike concept of the ratio of maximum compaction stress to an unconfined
stress – flow function ff – Stanley-Wood and Abdelkarim (1982) and Abdelkarim (1982) su-
perimposed the experimental parameters of unconfined and maximum compaction stresses,
for a range of industrial powders (liquorice, chalk 2, fine talc, chalk 1 and di-calcium
phosphate (DCP)) classed as either free flowing/non-cohesive, intermediate flowability or
cohesive, onto the various degrees of cohesiveness postulated by the Jenike flow function,
as outlined in Bulletin 123 (Figure 1.5).
Subsequently, this collection of powders was re-investigated in terms of a simple modified
Hausner ratio or flow ratio (FR) (Stanley-Wood et al. 1993) to discriminate between those
powders which could readily flow and those which had some degree of cohesiveness. This
10
Liquorice
ff = 1
Chalk 2
Talc Fine
8
Chalk 1
DCP
Unconfined stress fc (kPa)
ff = 2
6
ff = 4
ff = 10
0
0 10 20
Major consolidation stress (s1) (kPa)
Figure 1.5 Jenike flow function ff (degree of flowability), for a selection of industrial powders.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls December 21, 2007 21:17
Table 1.4 Calculation of flow ratios, for a variety of industrial powders, from the tapped and aerated
densities.
simple FR was then compared with other, more elaborate and time-consuming measurement
techniques for a range of industrial powders (Table 1.4).
Figure 1.6 shows the correlation between the complex Jenike failure function ff with
the simple FR (Table 1.4). These results indicate that for values of FR less than 1.25, the
industrial powders tested were free flowing. Above an FR value of 1.55, the powders could
be classified as cohesive with intermediate degrees of flowability between FR values of 1.25
and 1.55 as illustrated in Table 1.5.
100
10
Easy flow
Cohesive
Very cohesive
1
0 1 2 3 4
Flow ratio ( − )
Figure 1.6 Relationship between Jenike failure function (ff = σ1 / f c ) and a simple flow ratio (FR) for various
industrial powders.
r Hardness of particles
r Bulk density
r Cohesiveness of particles
r Moisture content
r Relative flow
r Potential strength of arches in bin/hoppers
An alternative and possibly a more comprehensive parameter may be one where the de-
gree of powder compaction is related to the degree of applied pressure in a log–log plot of
bulk density versus consolidation pressure. This degree of compressibility and degree of
relaxation is beneficial for the control of paste consistency or grindability of plastic-like ma-
terials as well as the determination of capacities required for processing and storage. Jenike
(1964) and Carson and Marinelli (1994) plotted log bulk density versus log consolidating
stress and determined the slope from the relationship:
σ
ρ = ρ0 B (1.2)
σ0
where ρ and ρ0 are the bulk densities at stress σ and σ0 respectively, σ0 being an arbitrary
stress chosen to be less than σ . For bulk solids the slope B was found to vary between zero
and unity. Most industrial and pharmaceutical powders, however, fell in the range 0.1–0.01
when compressed at high uniaxial stress (Prescott & Barnum 2000).
Table 1.7 A selection of National and International Standards allied to bulk powder properties.
Compression/compaction
Uniaxial ASTM B331-95 (2002): Standard Test Method for Compressibility of Metal
Powders in Uniaxial Compaction
ASTM E9-89a (2000): Standard Test Methods of Compression Testing of Metallic
Materials at Room Temperature
Moisture effects ASTM D1075-96 (2000): Standard Test Method for Effect of Water on Compressive
Strength of Compacted Bituminous Mixtures
Hardness
Micro hardness ASTM E1268-01: Standard Practice for Assessing the Degree of Banding or
Orientation of Microstructures
Brinell ASTM E10-01: Standard Test Method for Brinell Hardness of Metallic Materials
Indentation ASTM E103-84: (2002): Standard Test Method for Rapid Indentation Hardness
Testing of Metallic Materials
Strength
Fracture ASTM E1290-02: Standard Test Method for Crack-Tip Opening Displacement
(CTOD) Fracture Toughness Measurement
ASTM B646-04: Standard Practice for Fracture Toughness Testing of Aluminium
Alloys
BS ISO 12108 :2002 Method for Determination of the Rate of Fatigue Crack Growth
in Metallic Materials. Fatigue crack growth rates of above 10−8 m per cycle.
Tumble test ASTM C421-05: Standard Test Method for Tumbling Friability of Preformed
Block-Type Thermal Insulation
ASTM C1421-01b: Standard Test Methods for Determination of Fracture Toughness
of Advanced Ceramics at Ambient Temperatures
Crack displacement ASTM E1290-02: Standard Test Method for Crack-Tip Opening Displacement
(CTOD) Fracture Toughness Measurement
Compact tensile
Strength BS 1881-102: 1983 (withdrawn) now BS EN 12350-2: 2000 Method for the
Determination of Slump
BS 1881-103: 1993 Method for the Determination of Compacting Factor
BS 1881-119: Testing Concrete. Method for determination of compressive strength
using portions of beams broken in flexure
BS 1881-207: 1992 Testing Concrete. Recommendations for determination of strain
in concrete
Toughness
Fracture ASTM B646-04: Standard Practice for Fracture Toughness Testing of Aluminium
Alloys
ASTM B909-00: Standard Guide for Plane Strain Fracture Toughness Testing of
Non-Stress Relieved Aluminium Products
ASTM E399-05: Standard Test Method for Linear–Elastic Plane–Strain Fracture
Toughness K Ic of Metallic Materials
BS 5447: 1987 (withdrawn)
BS 7448-1: 1991 Methods of Test for Plane Strain Fracture Toughness (K Ic ) of
Metallic Materials
BS 7448-2: 1997 Fracture Mechanics Toughness Tests. Method for Determination of
K Ic , Critical CTOD and Critical J Values of Welds in Metallic Materials
BS 7448-3: 1997 Fracture Mechanics Toughness Tests. Method for Determination of
fracture toughness of metallic materials at rates of increase in stress intensity factor
greater than 3.0 MPa m0.5 s−1
BS 7448-4: (1997) Fracture Mechanics Toughness Tests – Part 4: Method for
Determination of Fracture Resistance Curves and Initiation Values for Stable Crack
Extension in Metallic Materials
(continued)
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls December 21, 2007 21:17
Abrasion
Attrition ASTM D4058-96 (2006): Standard Test Method for Attrition and Abrasion of
Catalysts and Catalyst Carriers
ASTM D4060-01: Standard Test Method for Abrasion Resistance of Organic
Coatings by the Taber Abraser
Tumble test ASTM E279-97 (2005): Standard Test Method for Determination of Abrasion
Resistance of Iron Ore Pellets and Sinter by the Tumbler Test
ASTM C421-05: Standard Test Method for Tumbling Friability of Preformed
Block-Type Thermal Insulation
ASTM D441-86 (2002): Standard Test Method of Tumbler Test for Coal
Physico-mechanical
General BS 1377-7: 1990 (2003) Methods of Test for Soils for Civil Engineering Purposes.
Shear Strength Tests (Total Stress)
BS 1377-8: 1990 Methods of Test for Soils for Civil Engineering Purposes Shear.
Strength Tests (Effective Stress)
BS 1377-9: 1990 (2003) Methods of Test for Soils for Civil Engineering Purposes.
In-Situ Test
BS 1377-4: 1990 Methods of Test for Soils for Civil Engineering Purposes.
Compaction related Tests
BS 1377-6: 1990 (2003) Methods of Test for Soils for Civil Engineering Purposes.
Consolidation and Permeability Tests in Hydraulic Cells and with Pore Pressure
Measurement
BS 1377-5: 1990 (2003) Methods of Test for Solids for Civil Engineering Purposes.
Compressity, Permeability and Durability Tests
Bulk density BS 6070-0: 1981 (2005) Methods of Sampling and Test for Sodium Carbonate for
Industrial Use – General introduction and Determination of Pouring Density
BS 5551 Part 3, Section 3.1 (1993). Replaced by BS EN 11236: 1995 Fertilisers.
Physical Properties Method for the Determination of Bulk Density (Loose)
BS 5551 Part 3, Section 3.2 (1983). Replaced by BS EN 1237: 1997 Fertilisers.
Physical Properties Method for the Determination of Bulk Density (Tapped)
BS 5551 Part 3, Section 3.3 (1989). Replaced by BS 5551-3.3: 1992 Fertilisers.
Physical Properties. Method for the Determination of Bulk Density (Loose) of
Fine-Grained Fertilisers
BS 5551 Part 3, Section 3.6 (1989). Replaced by BS EN 12047: 1997 Fertiliser.
Physical Properties Method for the Determination of Static Angle of Repose of Solid
Fertilisers
ISO 3923-1: 1979 Metallic Powders – Determination of Apparent Density – Part 1:
Funnel method
ISO 3923-2: 1981 Metallic Powders – Determination of Apparent Density – Part 2:
Scott Volumeter Method
(Ergun & Orning 1949). A modification of this fluidisation technique has been proposed by
Geldart (1990, 2005).
In an attempt to classify the fluid behaviour of powders, Geldart (1972) used the simple
method of grouping fluidisable powders into four groups. The three most important groups
being:
Group A – Aeratable: material which shows a range of smooth particulate expansion
between the minimum fluidisation velocity, Umf and the velocity at which bubbles
form, Umb .
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls December 21, 2007 21:17
B-powders
A-powders
103
C-powders
102
100 1000 5000 μm
Particle size d p (micrometre)
Figure 1.7 Geldart’s empirical classification of aeratable (A), bubble (B), cohesive (C) and dense (D) flu-
idisable powders.
Group B – Sand like: material which shows bubbles for all gas velocities above Umf .
Group C – Cohesive: material in which gas flow occurs through channels rather than
distributed throughout the interstitial voids.
These empirical observations (Figure 1.7) give a rough indication of the categories of
powders, which may possibly give storage and flow problems. This simple relationship
between particle size and the difference between particle and fluid densities fails, however,
to take into consideration other fundamental particle properties of cohesiveness, surface
attraction or elastic/plastic deformability of materials. Rietema and Hoebink (1977) and
Clift (1985) stated that the real differences between Groups A, B and C resulted from
inter-particle forces. Seville and Clift (1984) showed that by increasing the loading on
particles – using an involatile liquid to increase the capillary forces– the resultant increase
in surface attraction caused a movement in powder behaviour from an initial Group B (freely
fluidisable powder) through Group A and eventually to a Group C powder which showed
various degrees of cohesiveness.
Inclusion of other bulk powder properties such as cohesion (C), gas viscosity (μ) and
gravity (g), to Geldart empirical classification, can give a more informative dimensionless
correlation. The correlation of the Archimedes number [ρg dp3 (ρp − ρg )g/μ2 ] with a modified
Reynolds number [C/(ρg gdp )] can extend the empirical Geldart fluidisation classification
model to other powder handling operations such as mixing, transportation and separation.
Both Molerus (1982) and Rietema (1984) extended the Geldart classification to a di-
mensionless correlation for bulk powder behaviour (Figure 1.8). A more sophisticated
interpretation which takes into account particle interaction as well as particle forces has
been proposed by Molerus (1980).
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls December 21, 2007 21:17
B-behaviour
104
A-behaviour
103
C
Δρdgdp
1 10 100
Modified Reynolds number [C/Δρggd p]
Figure 1.8 Archimedes number versus modified Reynolds number for aeratable (a), bubbling (b) and cohesive
(c) powders at various voidages, ε (Molerus 1982; Rietema 1984).
1.4.6 Floodability
Floodability of a material is its tendency to have a liquid-like flow characteristic, which is
caused by aeration within the powder. Powders can, when discharged from a hopper, behave
in an unstable, liquid-like manner, which may be discontinuous, gushing and uncontrollable.
The reasons for flooding are generally due to excessive aeration within the powder bed,
which leads to easy powder fluidisation and ultimately to flooding.
Floodable powders tend to have:
r Large available external surface areas (i.e. small particles)
r Tends to adsorb gases
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls December 21, 2007 21:17
Powder Density (kg/m3 ) Mean particle size dp (mm) Hausner ratio (−) Flowability
Carr categorised the potential for powders to flood by using four parameters, each parameter
being given a ‘weighting’ of 25 points. Thus 25 points were allotted to each of the following
factors:
Summation of the above four factors contributes to a range of performance on a scale 0–100.
Protractor
Steel weight of 100 g
on a spindle, dropped 70 80 90
7 in onto plate to cause 60
powder to slump 50 Position from which powder
dropped to form heap
40
Indicator wire to measure angle
20
in 7 in
12
10 Angle of repose
Plate
Tray
10 in
Figure 1.9 Apparatus for the measurement of angle of repose, angle of fall and angle of difference (Carr
1965a).
The more dispersible a powder is the dustier (see Section 1.4.8) it becomes and therefore
the more floodable.
The degree of particle tensile strength was found by Yokoyama et al. (1982) to affect
the floodability of a powder. The floodability index, using the various test methods for
characterising bulk solids by the Carr’s indices (ASTM D 6393-99: 1999) was used to
evaluate an intermediate condition between an aerated powder and a packed dense powder
(see Section 1.8.1).
1.4.7 Flowability
The flowability of a powder can be predicted from a series of laboratory tests using four dif-
ferent bulk powder flow parameters in a similar manner to Carr’s floodability index. Flowa-
bility can thus be ranked from 0 to 100 using the four different bulk properties listed below:
Angle of repose
Compressibility
Angle of spatula
Either a uniformity coefficient or a cohesion factor
The choice as to whether a uniformity coefficient or a cohesion factor is selected is dependent
upon the particle or granulate size. Cohesion can be defined, from the results of a sieve
analysis, as the amount of powdered material expressed as a percentage of the initial charge,
added to the top sieve, compared to the amount of powder which remains either on the top
sieve or falls to the bottom pan of a set or nest of sieves. Thus, all particles remaining on
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls December 21, 2007 21:17
Drop point
4 in 1.D
7 in
Plastic
tube 13 in
4 in
Watch glass
a top sieve with a mesh size greater than the maximum particle size constitutes a being
100% cohesive, whilst in the situation where all particles pass through the nest of sieves,
which has a sieve size larger than the minimum particle size, are regarded as free flowing
(Figure 1.11).
Uniformity may also be defined from a sieve analysis. Uniformity is the ratio of the
specific sieve size which allows 60% of the initial mass of particles to pass through the
specific sieve size to the sieve size, which allows only 10% of the initial mass of particles to
pass. The smaller the ratio, the greater the uniformity of the powder. Powders with particle
sizes above 50–100 μm tend to have greater flowability due to having less cohesiveness and
more uniformity.
Nest of sieves
Known wt of
<75 μm particles
250 μm
Vibrate for known
length of time
147 μm (20–120 s)
Measure wt in
75 μm bottom pan
Figure 1.11 A method for the determination of the uniformity and/or cohesiveness of powders.
Hamelmann and Schmidt (2003) in terms of the applicability of any one test for the multitude
of industrial powders produced in the powder industry. Different methods have generated a
variety of standards from various and different industries but there is no definitive standard
on the measurement of dustiness in the powder industries. Carr determined dispersibility
or dustiness by simply dropping powdered material ‘en masse’ through a cylinder and
weighing the remaining material collected on a watch glass (Figure 1.10). A selected starch
powder was rated as having a 50% dispersibility because the starch sample lost 50% of its
weight when falling down the tube and cascading off the catchment plate. Any material
with 50% or more dispersibility was awarded 25 points.
Equipment available to measure dustiness varies from the drop method (Figure 1.10),
Roach dust drop funnel (Lyons & Mark 1992), drop test (DIN 5599-2: 1999), rotating drum
(Lyons & Mark 1994), inverse flow (Cowherd et al. 1989) and gas fluidisation (Schofield
1981).
1.4.9 Permeability
Since a powder assembly can generally be regarded as a biphasic system the permeability
of a powder, or the ability of a gas to pass through a collection of particles or bed of powder,
has now been recognised as a bulk powder property. The magnitude of permeability as
a function of bulk density may be used in the determination of the powder flow rate and
discharge of powders from hoppers.
The passage of gases (usually air) through fine powders may be a rate determining factor:
too high a rate can lead to non-steady or erratic flow whilst too low a rate may be witnessed
in ‘hold-ups’ or arching in hoppers, settling or deaeration.
Permeability is usually measured by the volume of airflow, q, at a specific pressure drop,
p, through a bed of powder of known bulk density, ρb , and height, L (Carman 1937). From
the knowledge of powder permeability the problems of non-steady or erratic flow may be
circumvented and thus prevent poor weight control into a compaction die or a hazardous
flooding discharge from a hopper. Permeability is generally determined using equipment
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls December 21, 2007 21:17
Normal stress
Cover
Wall material
for the measurement of an external surface area by the use of the Kozeny–Carman equation
(BS 4359 Pt 2: 1982) (see Section 1.4.4).
(Shear) Adhesion
Shear stress
Normal stress
Figure 1.13 Graphical representation of the parameters of adhesion to, and wall friction on, hopper or plant
material.
If the wall shear stress line is curved, a Mohr circle may be drawn in contact with the
powder yield locus of a separate shear test obtained at a pre-shear normal stress identical or
similar to that of the wall friction test (Akers 1992). The intersection of the curved WYL
with the superimposed Mohr circle is then extrapolated to the origin to give the angle of
wall friction.
In addition to wall friction, bulk density and shear strength are contributory factors to
the resistance to flow of powder in plant. McGlinchey and McGee (2005) and McGee
(2006) suggested that a visual diagram could be derived from the incorporation of the bulk
characteristics of wall friction (φw ), shear strength (τ ) and bulk density (ρb ), together with
hopper wall angle (βh ), hopper outlet size (Dcrit ) and the Hausner ratio to produce a six axes
‘spider web’ diagram (Figure 1.14). The spider web diagram gives no numerical values for
flowability but the position of a hatched area within three concentric circles, designated as
easy (inner circle), moderate (middle circle) and poor (outer circle), gives an indication of
bulk powder flowability.
Table 1.9 shows the suggested limits of the three ‘webs’, which were subsequently used
to describe the flow of over 100 industrial powders.
(a) (b)
ρb ρb
HR Dcrit HR Dcrit
φw τs φw τs
βh βh
Figure 1.14 ‘Spider’s web’ diagram of easy (a) and poor powder flow (b) (McGlinchey & McGee 2005).
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls December 21, 2007 21:17
Table 1.9 Bulk powder parameters, which may characterise the degree of flowability of various
industrial powders.
Wall friction Bulk density Shear strength Hausner Outlet Mass flow
Flow (degree) (kg/m3 ) (N/m2 ) ratio (−) size (cm) wall angle (degree)
Funnel
Bridge
5.2 cm
r Fluidity
r Bulk density
Although the angle of repose has been used to design feeders and storage bins, there is,
nowadays, more sophisticated and accurate instrumentation available to measure other bulk
powder factors such as:
r Jenike angle of friction
r Wall friction
r Cohesion
r Tensile strength
which are generally better criteria for use in mass flow hopper design.
Probably the only general powder standard to describe the procedure to measure an angle
of repose is that described by British Standard (BS 4140-9: 1986) while there are three ISO
standards for different powdered materials, ISO 902: 1976, for alumina; ISO 4324: 1977,
for powders and granules and ISO 8398: 1989, for fertilisers. The apparatus consists of a
glass or polythene funnel with a cut-off stem mounted on a tripod at a known height (5.2
cm) above a plate of metal or wood. This bottom plate has a series of concentric circles
inscribed upon its surface to indicate the different angles of the poured conical surface. The
diameters of the circles are calibrated in degrees with a step size of 2◦ (Figure 1.15). A
commercial instrument for angle of repose measurement for use in the process control of
semi-cohesive powders has been developed (Powder Research Ltd, Harrogate, UK) from
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls December 21, 2007 21:17
Table 1.10 Flowability indicators and categories of powder flow from USP 29-NF24 (2006).
Description of flow Angle of repose (degree) Carr’s compressibility (%) Hausner ratio (−)
the work of Wouters and Geldart (1996). The magnitude of the angle of the heap can be
used to quantify, in a similar fashion to the Carr’s compressibility percentage, Jenike failure
function and Hausner ratio, the ease of powder flow (Table 1.10).
Bodhmage (2006) following the work of Riley et al. (1978) correlated the physical prop-
erties and flowability indicators of six pharmaceutical powders. The six pharmaceutical
powders were Aspartame (a non-carbohydrate sweetner), Respiose ML001 (an inhalation
lactose), alpha-D-lactose monohydrate, Methocel HPMC (a water-soluble hydroxypropyl
methycellulose), pastry flour and a granulated placebo mixture. The flowability indicators
chosen were the static angle of repose, Hausner ratio, Carr’s compressibility percentage or
flow index and the dynamic angle of repose. The dynamic angle of repose was measured by
a modified Aero-Flow Analyser. When the ‘non-dynamic angle of repose’ indicators were
compared with the ‘saw-tooth’ frequency of avalanching data – mean time to avalanche –
from Bodhmage’s newly modified electrical capacitance tomographic instrument, it was
found that all six pharmaceutical powders followed the same rank order as the more con-
ventional indicators (Table 1.11).
Many of the empirical flow indicators currently used have been derived from the work of
Carr (1965b,c). These diverse test methods have now been collected together in an American
Society for Testing and Materials – ASTM D 6393-99: 1999 – standard which covers the
apparatus and procedures for measuring the properties of free flowing and moderately
cohesive bulk solids and which are collectively known as ‘Carr indices’.
1.6 Bulk powder flow properties from internal angles and shear
The above seven parameters are used to account for the amount of shear a powder has
to be subjected to before that powder can move under stress. The degree of compaction
or consolidation influences the flowability of power unless the powders are cohesionless
(e.g. dry sand, gravel) and thus have no compaction strength. It would be incorrect to
design powder handling and process plant on the quantitative fingerprinting characteristics
of powders, such as angle of repose, because although the angle of repose is useful in the
evaluation of hopper volume, the angle of repose does not measure the force or strength of
attraction between particles, which is measurable by a shear test.
Failure properties are strongly influenced by humidity, temperature and time of consolida-
tion. The above failure properties must, therefore, be measured under controlled conditions
of temperature and humidity. For any prolonged storage, samples must be sheared on time
consolidated samples.
A direct way to assess the rate of flow is to time the passage of a standard amount of
powder discharged from a specified funnel, opening or hopper (ISO 4490: 2000; ASTM
B855-06).
1.6.2.1 Interfacial sliding of particle assemblies The frictional work required to cause
particles to slide over each other and to initiate powder flow in a particle assembly depends
upon both macroscopic and local microscopic particle involvement. The macroscopic level
can be regarded as the level in which bulk flow of a powder occurs down container or
hopper walls. This flow can then be regarded as analogous to the frictional flow of solid non-
particulate bodies. Nedderman and Laohakal (1980) found that flow of particle assemblies
down smooth walls could be described as virtual plug flow, with a constant velocity profile
across the whole cross section of the body of powder undergoing movement.
At the microscopical particle level, the contribution to sliding and flowing is due to the
interplay of particle surfaces and surface energies achieved by rolling particles. These modes
of movement may, however, be co-incidental because a rolling particle will eventually be
transposed, in an assembly of particles, by inter-particle sliding and therefore failure.
For rough walls, Stephen and Bridgwater (1978) found that the failure zone area, for
the internal failure of powders, was twice the number of particle diameters reported by
Nedderman and Laohakul. These failure zones can be related to the voidage fluctuations
seen in randomly packed beds of spheres adjacent to container walls (Ridgway & Tarbuck
1968). It is generally found that the internal angle of friction is greater than the wall friction.
Contact surface roughness is therefore a significant factor in the frictional behaviour of
solid surfaces and thus applicable to any moving particulate system. Particle movement
can be conceptualised either as a model of smooth contact between particles and walls
(Hertzian: Hertz 1882) or as a model which has rough contact area between the particulate
system and wall (Archardian: Archard 1953, 1957). Both models have been used to predict
the physical behaviour between particles and particles or between particles and a wall.
The more realistic powder technological model of Archard (1953, 1957) demonstrated
that with rough contact surfaces the surface consisted of many micrometre-sized asperities
or surface projections. The ‘real’ area of contact was therefore dependent upon two criteria:
one criterion being the number of asperities that were brought, under certain loads, into
contact with each other, whilst the other criterion was the degree of plastic deformation
these asperities could undergo. The change in both the asperity size and height distribution
on particle surfaces thus alters the contacting surface area and the sliding or friction between
solid particles.
Kendall et al. (1971) and Kendall (1986) showed that it is not possible to obtain a value
of Hertzian contact area based on particle geometry of fully roughened particles because
the coefficient of friction increases with wet sands, lubricated by adsorbed moisture, with
decreasing particle size.
Changes in the surface topography of rough surfaces need to be considered in all particle
movements since contact forces are small. A small force of 100 nN has been shown to change
the surface topography of the contact region and influence interfacial friction coefficients
and interfacial shear strengths. Briscoe et al. (1984) investigated the influence of surface
topography on the interfacial friction of powders from the flow behaviour of smooth (bal-
lotini spheres) and rough (silica sand) particles rotating and sliding in a horizontal cylinder
of borosilicate glass. They concluded that the interfacial frictional properties and physical
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls December 21, 2007 21:17
behaviour of bulk powders could possibly be predicted from knowledge of microscopic par-
ticle properties. These predictions were valid if powder behaviour was approached from the
viewpoint of an adhesion–friction model because with smooth surfaces, detailed analysis
of rotating particulate systems are capable of accurately predicting frictional forces from
measured values of torque. Measured torques could then be converted into forces acting
over a known contact area, and the normal force evaluated from the weight of particles in the
rotating tube at known packing densities which can lead ultimately to the failure property
of the powder.
1.6.2.2 Flowability based on hopper discharge The prediction of the rate of discharge
of granular materials from conical mass hoppers should take into account the friction of the
materials and the effect of container wall friction.
A number of mechanical models have been proposed for powder discharge rates. Some
of the earlier equations for discharge were based on models which were for coarse (>500
μm diameter) free-flowing particles. These cohesiveless powders either discharged in a
manner regarded as non-mass (funnel) flow (Beverloo et al. 1961) or as mass flow (Brown
& Richards 1970; Johanson 1965). Although both the Johanson and the Brown and Richards
models are widely used with non-cohesive, free-flowing material, for cohesive powders the
models of Davidson et al. (1966), Davidson and Nedderman (1973) and Williams (1977)
have shown better success in terms of coincidence between theory and reality. Both the
cohesive models – Davidson and Nedderman and Williams – and their predictive equations
take into account the internal friction of powdered material. The Davidson and Nedderman
model, built on the initial work and experimentation of Savage (1967), assumes a frictionless
hopper wall whilst the Williams model takes into account both internal friction and hopper
wall friction. The mathematical models of Johanson, Beverloo, Brown and Richards and
Williams all show a relationship between discharge rate and hopper outlet diameter to the
power of 2.5.
Johanson
π D2 Dg 0.5
Q=ρ (1.4)
4 4 tan θ
for conical hopper outlets
Beverloo
Q = 0.58ρg 1/2 (D − kdp )2.5 (1.5)
Brown and Richards
1/2 5/2 π cos3/2 θ
Q = ρg D 1− (1.6)
6 sin5/2 θ
Davidson and Nedderman
4π cos3/2 θ × Vw
Q=ρ 1− (1.7)
3 cos5/2 θ
Williams
Q = kc ρg 1/2 D 5/2 (1.8)
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls December 21, 2007 21:17
6 cm
25 cm
Hopper discharge flowrate
Measuring cup
where Q is the mass discharge; θ is the semi-included angle of a conical hopper; ρ is the
bulk density of granular or powdered material; g is the gravity; D is the diameter of hopper
outlet; Vw is the function of the velocity along the hopper wall; k is the Beverloo constant
which, with particle diameter, dp , accounts for the wall effect when particles do not fully
flow at the perimeter of the outlet. k has values between 1.3 and 2.9 with an average value
of 1.4. kc is the correction factor for hopper outlet diameter.
Direct measurement of flow through various-sized orifices may, however, be obtained
by use of very simple laboratory equipment (Figure 1.16), and also instruments described
in ASTM B855-06 and ISO 4490: 2000 or even with the patented Flodex commercial
apparatus.
1.6.3.1 The unconfined yield stress ( f c ) This is defined as the maximum principal stress
which can act along a free surface to cause failure, instability to arching or the doming of
powders in a hopper. Essentially the unconfined stress is used in the design of mass flow
hoppers and is regarded as the stress which must be applied to any arch or dome to cause
an arch to collapse under gravity from the weight of the powder above the arch or dome.
A Mohr circle which describes the situation of normal stress on the powder surface of the
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls December 21, 2007 21:17
(a)
Yield locus
Shear stress
Equilibrium end point
d
fc s1
Compressive stress
(b)
Shear stress
dE
fc s1
Compressive stress
Figure 1.17 Yield loci for the determination of Jenike effective angle of friction (δ) (a) and internal angle
of friction (δE ) (b) from the critical state line (CSL) ( f c unconfined yield stress and σ1 major consolidation
stress).
arch accompanied with a tangential stress along the surface of the arch must pass through
the origin of the shear–normal stress relationship graph and also touch the yield locus of
the powder which has been compacted at a specific densified state. The unconfined yield
stress is then the value of stress when the limit of the Mohr semi-circle cuts the maximum
principal stress x-axis of the shear–normal stress graph (Figure 1.17).
1.6.3.2 Major consolidation stress (σ1 ) This is the principal normal stress (σ1 ) under
which the sample has been consolidated in the principal stress plane. The major consolida-
tion stress should not be confused with the initial compaction stress, σc , which is the stress
that compacts the powder bed. Each different compaction stress, σc , leads to a different
yield locus and becomes one of a family of yield loci at different densifications. The major
consolidation stress is obtained by drawing a Mohr semi-circle through the equilibrium or
end point of the yield locus and tangential to the yield locus.
This equilibrium stress is found when there is no volume change occurring in the pow-
dered sample when stressed. The Mohr semi-circle, tangential to the locus, then cuts the
normal stress axis to give σ1 .
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls December 21, 2007 21:17
1.6.3.3 Jenike failure function (ff) This is the relationship between the unconfined yield
strength ( f c ) and the major consolidation stress (σ1 ). A plot of the values f c versus σ1 shows
the possible relationship of the rate of flow of powdered material out of hopper orifices.
Jenike could classify the flowability of powders from selected ratios of these values.
The Jenike failure function necessitates the measurement of a number of yield loci (min-
imum 3) to obtain both f c and σ1 values. The relationship between f c and σ1 may be linear
or non-linear but must not pass through the origin of the graph.
If the failure function does pass through the origin then these powders are defined as
simple powders (Williams & Birks 1965, 1967).
In order to achieve unique numbers for various and different degrees of flowability Jenike
calculated the failure function at a specific value of the unconfined stress. The specific value
of the ratio of the major consolidation stress to the unconfined stress was taken as 6.5 lbf/ft3
(3.11 kPa) in the initial, Jenike designed, 4 inch diameter shear cell, because at this value
the relationship between f c and σ1 showed only small deviations from linearity. Currently
a value of 3 kPa is generally used with a standard shear cell tester.
powder characterisation and the standard shear testing technique (SSTT) (ASTM D6773-
02) was thus developed. A commercial Standard Shear Tester is now manufactured by Jenike
& Johnson Inc. whilst the protocol and technique for the standard shear test is published by
the Institution of Chemical Engineers.
Novosad (1990) concluded that if the SSTT is strictly maintained in a geometrically
specified SST or Jenike shear cell, then it should be possible to obtain reliable and repro-
ducible measurement of the (Jenike) flow functions of cohesive powders. If the (Jenike)
flow function obtained by SSTT is compared with flow functions obtained from different
shear cells and different shear testing techniques there is no necessity that there should be
agreement in the results. It is essential, however, that whenever shear tests are recorded the
technique used must be quoted. Preference should be given to the SSTT together with the
modifications used for filling the cell, the optimisation of the specimen (i.e. the creation of a
critically consolidated sample), designation of the equilibrium endpoint on the critical state
line (Schofield & Wroth 1968) and the twisting and inclusion of the shearing ring weight
into the total vertical normal stress. These recommendations, outlined by Novosad, were
used to certify a reference material of cohesive limestone powder – entitled CRM116 – by
the Community Bureau of Reference (BCR) for use with the Jenike shear cell and SSTT
(Akers 1992).
Enstad and Maltby (1992) concluded, from a series of shear tests carried out by five
different laboratories on the certified material, CRM 116, that reproducible flow function
results can be obtained only with skilled and experienced operators. Harwood (1971) applied
the technique of Jenike to evaluate the flow of a range of pharmaceutical powders and found
that as size of the powder increased the flowability became more free flowing (Table 1.12).
Shear stress
Figure 1.18 Schematic diagram to show the parameters of cohesion and tensile strength.
separation of a consolidated powder bed. All other ways are indirect since they measure
properties related to, or as a consequence of, internal attraction and cohesive forces.
One approach to measure the cohesiveness of a powder is to determine the yield locus of
the material, and then extrapolate the yield locus to zero normal stress. The intercept value
on the shear stress axis is then the cohesiveness or adhesion of the material (Figure 1.18).
1.7.1.2 Tensile strength The tensile strength of a powder can be regarded as the comple-
tion of the yield locus in the shear stress–normal stress profile. The negative stress, at zero
shear, to break apart the consolidated particulate powder is thus termed the tensile strength
of a powder (T ).
Measurement of tensile stress cannot be measured directly with a Jenike shear cell or
an annular shear tester, although one approach in the measurement of tensile strength of a
powder is to determine the yield locus of the material and then to extrapolate part of this
locus to zero normal stress. The negative intercept on the normal stress axis is the tensile
strength of the material under investigation (Figure 1.18).
Tensile strength is a fundamental failure property but tensile strength testing is dependent
upon the direction of force necessary to cause separation of a bulk structure with respect to
the direction of compaction or consolidation. Split cell testers pull the sample apart at 90◦
to the direction of compaction whilst the lifting lid or vertical shear testers pull in the same
direction as the compaction/consolidation stress was applied. Results obtained from both
methods differ greatly because tensile testing has a poor record of reproducibility, possibly
due to the fact that consolidated powders in the tester cells may not be isotropic.
1.7.2 Split cell and lifting lid (vertical shear) instruments for tensile
strength and cohesiveness
Although estimation of tensile strength, adhesion and cohesion from a Jenike shear test
yield locus is the easiest and less demanding way of assessing powder stresses, there are
other types of equipment which attempt to measure cohesion and tensile strength.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls December 21, 2007 21:17
Basically there are two techniques, both of which are categorised by the direction of
‘pull’:
(i) Split cell testers which separate the consolidated powder bed at 90◦ to the direction
of consolidation
(ii) Lifting lid testers which separate the consolidated bed in the same direction as the
compaction force
1.7.2.1 Split cell testers Tensile strength measurements may also evaluate internal ad-
hesion properties, independent of the mechanical interaction of shear plane, because T is
measured at zero shear. Warren Springs Laboratories (WSL) designed two instruments: one
to measure the cohesive strength of powders at varied states of compaction and the other to
measure tensile strength. The tensile strength measurement equipment, developed by WSL,
was the WSL tensile tester, a diametrically divided split shallow circular cell.
Before Ashton et al. (1964) developed the split cell apparatus for the measurement of the
powder tensile strength the method used was a tilting plate. This method, however, made
no provision for the consolidation of a powder at different bulk densities and the angle of
inclination could only be measured, at best, with an accuracy of 5%.
(a) Ashton, Farley and Valentin split cell tensile tester: With the Ashton et al.
(1964,1965) split cell, reproducibility in the results from tensile testing was found
to be better than 0.5%. The apparatus consisted essentially of a shallow vertically
split cylindrical cell with one half fixed and the other half movable upon ball bear-
ings. Instead of using gravity force to fracture the sample, the tensile stress was
applied horizontally through a pair of calibrated springs, which were extended us-
ing a motorised rack and pinion mechanism (Figure 1.19). The calibrated system
recorded the force necessary to separate the powder compacted at various values of
bulk density. Farley and Valentin (1965, 1967/68) used the WSL tensile tester, in
conjunction with the Jenike failure function tester, to investigate the flow properties
of a wide range of cohesive powders. The powders chosen were primarily those with
a reasonably constant particle shape, wide range of sizes and densities, i.e. precipi-
tated calcium carbonate, mined calcium carbonate, aluminium oxide and zinc dust
(see Figure 1.30).
The correlation between cohesion and tensile strength, at identical packing den-
sities, appropriated to the relationship:
C = 2T. (1.9)
Hartley and Parfitt (1984) improved the split cell tensile strength apparatus by sepa-
ration of the split cell of Ashton et al. (1964) to allow higher packing densities. The
rack-and-pinion application was also replaced by a vibration-free variable speed
mechanism. This was a vast improvement over the Ashton et al.’s original appara-
tus and that of the pulley and string mechanism of Yokoyama et al. (1982). This
improved instrument thus allowed the tensile strength of carbon blacks to be mea-
sured to an accuracy of better than 0.1%. The apparatus once again consisted of
three basic sections: a split cell and clamp, a compaction unit and a base unit with
means to separate the split cell and measure the tensile stress as a function of time.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls December 21, 2007 21:17
Split cell
Movable plate
The entire apparatus could be used in humid environments. The movable plate was
suspended on low-friction ball bearings.
(b) The Hosokawa Micron cohetester: An alternative to the split cell instrument is the
swing method developed by the company Hosokawa Micron Ltd. This measured
bed expansion in addition to tensile strength by drawing and breaking a powder bed
compressed in a split cell. The movable half-cell suspended by three plates, instead
of moving over ball bearings, was pulled apart at a constant velocity of 2 mm/min.
A linear variable differential transducer (LVDT) measured the linear displacement,
the core of which is fixed to the movable half-cell and the coil to the stationary
half-cell. The tensile stress and horizontal displacement was recorded on an X –Y
plotter (Yokoyama et al. 1982) (Figure 1.20).
1.7.2.2 Lifting lid testers for tensile strength Boden (1981) developed a lifting-lid tester.
This type of technique, recommended for the monitoring and comparison of cohesiveness,
is easier to use and gives results with less scatter than with annular shear cells. A mould in
the form of a ring, like a Jenike shear cell ring, is used with a metal lid just fitting inside.
The base of the cell and the lower face of the lid are covered with adhesive tape, onto which
glue is spread. The cell is filled with the powder to be tested and scraped level with top of
the cell. The lid, with the lower face covered with glue, is placed on top of the sample and
a compacting load applied to the lid and left in position until the glue has hardened. The lid
is then slowly lifted by an electric motor via a tensile load cell. The stress required to break
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls December 21, 2007 21:17
LVDT v v
Operational amplifier
Plan
Fixed half-cell
Strain gauge
Motor
X-Y Recorder
the powdered specimen is recorded and both the lid and base of the cell are examined after
failure to ensure that both are covered with powder. This indicates that failure has occurred
within the powdered specimen and not at the powder-lid surfaces. If both surfaces are not
covered with powder the test is rejected.
The instruments available for direct measurements are mainly associated with two classes
of devices. One class measures the torque or stress on an immersed vaned paddle in a bed
of powder compressed at a known bulk density, whilst the other class is the mould or
column failure method. The more practical mould devices are those based on the forma-
tion of a powder column in a cylindrical container (sometimes split into two halves) (see
Section 1.7.3.2). The container walls are then removed to leave a freestanding cylindrical
column of powder, which is then subjected to loads placed on the top of the column until
the column fails.
1.7.3.1 AJAX Equipment (Bolton) Ltd & Warren Springs Laboratory cohesion tester It
is appropriate to include in this chapter an instrument which was one of the first attempts
to measure the cohesion of powders directly. It was initially developed at Warren Springs
Laboratory, Stevenage, but is now commercially available from AJAX Equipment (Bolton)
Ltd.
Cohesion of a powder is defined as the shear strength at zero normal load. The tester is thus
designed to assess the cohesive strength of powder samples at varied states of compaction,
from lightly settled conditions to firm uniaxial compressed compacts. The bench-mounted
equipment consists of a radially finned vane mounted on a vertical spindle, which in turn is
carried on low friction bearings (Figure 1.21).
The weight of the eight vaned 100 mm outer diameter head is supported mechanically by
a small spring to give a ‘floating head’ arrangement. This is positioned above the powder,
which has been compressed and prepared in a cell similar to the technique used with other
bulk powder failure tests. The compaction pressure initially applied to the powder being of
the order of 10 kPa. The vaned paddle is lowered until the radial fins penetrate and are just
covered by the powder surface. The cell containing the powder being ‘keyed’ into the base
Tension spring
Raise/lower test head
Torque pulley
Loading screw
Stand
Figure 1.21 AJAX (Bolton) and Warren Springs Laboratory (WSL) cohesion tester.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls December 21, 2007 21:17
of the tester by rotating the paddle into a position in which the forces acting normally to
the powder surface are minimised and the vaned paddle weight is balanced by a spring to
ensure that no external force is acting on the powder. Torque is then applied to the paddle
via rotation and calibrated coil springs until a sudden deflection within the powder occurs.
This signifies that failure at the yield point of the compressed powder has occurred between
vane and the compacted powder in the cell. The area of the failure plane is taken as the
horizontal area between the vanes of the paddle and cohesion may then be calculated from
the recorded torque. Consolidation of the powder can be either instantaneous or over a
period of time (time consolidated). The sample container may also be weighted with the
powdered contents to ascertain the bulk density of the sample.
An alternative procedure, to ensure no external force is applied to the powder bed by
the vaned paddle, is to place the compacted sample on a balance and when the paddle is
immersed in the powder to raise the vaned head slowly until the balance reading is zero.
This dynamic method of bulk powder characterisation is allied to the rheological method
for measurement of the viscosity of non-Newtonian fluids and suspensions. Commercial
instruments based on the WSL cohesion tester are now available in the form of the FT4
Powder Rheometer (Freeman Technology) and the Stable Micro Systems Powder Flow
Analyser (Stable Micro Systems).
1.7.3.2 Cylindrical mould testers The ratio of the length of the cylindrical specimen (L)
divided by its diameter (D) is of major importance since a compromise must be sought
between two conflicting demands.
Firstly, friction between the mould wall and the powder causes a variation in vertical pres-
sure throughout the specimen which can result in a variation in the bulk density throughout
the column of powder. This bulk density variation can in turn cause variation in the strength
measurement. If wall friction is too pronounced, this will affect the longitudinal strength of
the powder column and the specimen will fail at its weakest point, usually near the lower
end of the column. To obtain a uniform vertical stress distribution throughout the column,
the L/D ratio should be as low as possible.
Secondly, the ratio L/D cannot, however, be made too low (Kesler 1959) since it has
been found that the crushing strength of cylindrical specimens is a function of L/D. There
is a critical value of L/D which must be exceeded for the measured crushing strength to
be independent of the L/D ratio and to ensure the failure plane does not intersect the end
plate of the powder column.
Monick (1966) assumed that failure planes are formed at an angle of 45◦ to the horizontal,
which would give a critical L/D equal to unity. Specimens are known, however, to fail along
slip planes at angles greater than 45◦ ; therefore the critical value of L/D should be greater
than unity.
The critical L/D dimension is one in which the failure slip plane coincides with or
exceed either of the diagonals drawn within the vertical cross-sectional area of the free-
standing column. The critical value of L/D is a function of the angle the diagonal within
the freestanding column makes with the horizontal plane on which the column stands and
the angle of internal friction (Endersby 1942). If the L/D ratio is lower than the critical
L/D value, there is likelihood that for some powders, the failure plane will intersect one of
the end planes. This mode of fracture (slippage) therefore requires extra work and produces
a higher collapse or cohesive strength value. Bishop and Green (1965) and Williams et al.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls December 21, 2007 21:17
(1970/71) found that end plate slippage became negligible when the L/D ratio was higher
than 2, failure occurring within the powder column.
All direct mould testers consolidate material by uniaxial compaction and since the voidage
within the compressed specimen may not be uniform, steady state deformation may not be
achievable and the failure functions measured may have some degree of inaccuracy.
Mould sections
D/
2
Guide plates
Base/bottom plates
Figure 1.22 Williams mould for the determination of unconfined stress (Williams et al. 1970/71).
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls December 21, 2007 21:17
15
σc = 21.0 p.s.i
fc (p.s.i)
10
σc = 14.8 p.s.i
5 σc = 8.37 p.s.i
Figure 1.23 Williams mould data for the determination of a powder’s unconfined yield stress (Williams et al.
1970/71).
the column collapses. The unconfined yield strength of the specimen was determined by
the measurement of the vertical stress applied to the upper end by means of a strain rate
device. From the measurement of the unconfined yield strength on columns produced with
varying numbers of N increments, a plot of unconfined yield strength versus 1/N can be
obtained (Figure 1.23). Extrapolation to 1/N = 0, which corresponds to an infinitely large
number of increments of zero thickness, gives a value of the unconfined yield strength. It
is assumed, when the number of layers are greater than 10, that wall friction plays no role
and probably gives a better estimate of the unconfined yield strength of the material.
The principal compaction stress is
L
σ1 = (1.10)
A
where L is the compaction load and A is the cross section of the split mould.
The unconfined yield strength is
W − Wp
fc = (1.11)
A
where W is the total applied weight to cause column collapse and Wp is the weight of
powder initially in the mould.
Since the L/D ratio of the mould designed by Williams et al. was 3.5, the strength of the
compact was deemed to be independent of the L/D ratio.
The failure function of titanium dioxide obtained from a family of yield loci measured
in a Jenike shear cell was found to agree closely to those obtained with different values of
N from the mould or unconfined compression test equipment. Although the consolidation
stress needed to form a satisfactory column is higher than that normally found near the outlet
of hoppers, it is within the range of stresses expected to occur in other powder flow systems
such as screw conveyors, mixers and extrusion presses. Higher stresses of compaction and
unconfined yield strength can be achieved with the use of an Instron Universal testing
machine. A similar technique to Williams et al. has been used to measure the tackiness of
detergent powders (Lappas & Dempski 1965; Labuza 2002).
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls December 21, 2007 21:17
water
Figure 1.24 Gerristen’s mould and method for the measurement of unconfined yield stress (Gerristen 1986,
1990).
1.7.4.2 The Gerritsen method Gerritsen (1986) pointed out that the densification of each
of the increments in the Williams et al. method was not consolidated for the same period of
time. Thus, the measured unconfined yield stress may not be applicable for materials which
exhibit a time consolidation dependence.
Gerritsen thus designed an apparatus which allowed the determination of the unconfined
yield strength at low consolidation stresses (Figure 1.24). The column formed, however,
has to be able to withstand at least its own weight; thus there is a certain minimum major
consolidation stress for each material and the height of the sample had to be as low as pos-
sible. In order to solve the contradictory requirements of an acceptable L/D ratio (circa 2)
to avoid the failure plane intersecting the end plane and a low L/D ratio to avoid mould
wall effects, it was proposed to form a compacted column using a mould with a low L/D
ratio and cutting away the outer part of this column. This action left an inner cylinder with
a sufficiently high L/D ratio for the sample to be acceptable for the subsequent test.
The mould has a diameter of 19 cm, which can be filled with a given weight of material to
achieve a height after consolidation of approximately 7 cm. A thin aluminium disk, smaller
in diameter than the mould, is placed at the centre of the sample surface. An airbag is placed
between the aluminium disc, powder surface and consolidating lid. A consolidation stress is
then exerted on the sample through the bag to achieve an even pressure/stress distribution.
After consolidation the compaction force and mould are removed. Most of the bulk solid is
then cut away to leave only the central part of the column under the aluminium disc. The
unconfined yield strength of the test sample is obtained by the addition of weights to the
top of the column until the column collapses. The value of f c obtained by Gerristen, and
subsequently used to determine a critical diameter to prevent arching in a hopper, was found
to be less than the f c values that were required to prevent arching in a practical experimental
hopper and the f c values obtained with a triaxial tester.
Locking pin
Figure 1.25 Procter & Gamble’s apparatus for the determination of cake strength (Lappas & Dempski 1965;
Labuza 2002).
small f c values since its direction of application is different from that of the consolidating
stress (Peschl 1988, 1989).
1.7.4.4 Procter & Gamble device for cake strength measurements The apparatus consists
of a cylinder, sleeve, lid and locking pin (Figure 1.25). The locking pin is placed in the hole
in the cylinder and the sleeve rests on the pin. The sleeve is filled with powder and the
lid placed on top of the sleeve with both parts of the device being fastened together by
elastic bands. The pin is then removed and a 12 lb weight remains on the lid for 2 minutes to
compact the sample. After removal of the elastic bands and the weights, the sleeve is retracted
down the cylinder to the base. A force gauge is applied to the lid and the force required to
fail the exposed column of powder is noted. This is regarded as a direct measurement of the
cohesiveness of the material (Labuza 2002).
The L/D ratio of this device is not fixed since it is dependent upon the powder com-
pressibility. The sleeve is 15.25 cm long and has an inner diameter of 6.35 cm; the pinhole
is located 6 cm below the top end of the solid cylinder, so that in case of an incompressible
powder the L/D ratio will be roughly 1.5, and even less for compressible powders.
1.7.4.5 Large-scale uniaxial tester For coarse granular materials a split mould is used
which has an L/D ratio of 2 (Tamura & Haze 1985). The height and diameter of the mould
used are dependent upon the size of the granular material. The granules are compacted in
three layers in three similar compression steps. The failure criterion is regarded as the value
of the compaction stress at which the column could not remain freestanding.
mimics the force generated at the bottom of a pile of bags filled with soap intermediates or
detergents and approximates to a stress of 16 kPa (Figure 1.26).
Although the amount of weight to cause column collapse prepared at 98 N is defined
as ‘tackiness’, other loads may be used to form columns which subsequently collapse at
known added weight. The shape of the curves generated from these experiments gives an
indication of the ‘tackiness’ or non-tackiness of materials.
Sticky material may also be classified by the determination the measurement of the wall
friction on plant equipment (Figure 1.13). Moisture increases tackiness as does dust content
and the melting point of detergents and soaps. Techniques and the methodologies used to
measure the tackiness of detergent powders and pharmaceuticals were reviewed by Lappas
and Dempski (1965), while recently Adhikari et al. (2001) have reviewed the mechanisms
of stickness in foods.
1.7.4.7 Compressibility A powder sample can be compressed in a shear cell ring, mould
or punch and die and the powder displacement recorded. The slope of the line generated
by the volume of powder, void ratio (volume of voids/volume of solid) or displacement
versus the logarithmic applied stress is a measure of the compressibility of bulk solids. The
simplest method to test compressibility (wet or dry) is the uniaxial compression of a powder
in a consolidometer or oedometer (BS 1377-7: 1990; ISO/TS 17892–5:2004).
1.7.4.8 The Johanson indicizer system Johanson (1987, 1992) developed a novel system
called the Hang-up indicizer to determine a powder flow function and to replace the tedious
evaluation method of Jenike. The bulk sample is contained within a cylindrical test cell
(Figure 1.27). The cell bottom is supported during consolidation to obtain a flat sample
surface. The sample is consolidated by a two-part upper piston. The consolidation pressure
is applied for a pre-set time. The outer part has a sliding fit to the cylinder. The inner piston,
which is attached to a load cell, measures the force on the inner piston and is independent
of the friction between the cylinder and the outer part of the piston. The two-part upper
piston is then retracted and the bottom support removed, leaving the sample supported only
by a ledge around the cylinder’s circumference at the bottom end of the cylinder. The inner
piston is then moved downward to fail the sample and to measure its strength. This empirical
failure strength is multiplied by a factor of about 2.2 chosen from comparable tests with
other methods, to obtain the unconfined yield strength of power.
Johanson claims that this new approach produces a similar powder flow function in one
tenth of the time required by the Jenike test. However, Enstad and Maltby (1992) and
Schwedes and Schulze (1990, 1992) criticised the Johanson method and doubted whether
the measured failure stress was representative of a material’s unconfined yield strength, even
after the application of a correction factor. This observation was confirmed by Marjanovic
et al. (1995, 1998) with five powders (Table 1.13).
Bell et al. (1994) compared the Johanson indicizer – a unixial direct shear tester – with
a Jenike shear cell and a Peschl rotational shear cell on nine various powders, having an
overall size range of 600–0.61 μm, from a certified reference powder (BCR limestone,
CRM-116) to white wheat, sub-micrometre mineral oxides and a polymer. The values of
the unconfined yield strength ( f c ) and the arching and rathole diameters determined by the
indicizer were often appreciably smaller than those determined by the Jenike and Peschl
shear cells (Figure 1.28). Table 1.14 shows the variation of an unconfined yield stress, f c ,
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls December 21, 2007 21:17
Piston shaft
Clamp
Cylindrical mould
Failure
plain
Test cell
Lower piston
at various major consolidation stresses (σ1 equal to 2.87, 9.58 and 19.15 kPa) for a selected
number of powdered materials.
1.7.4.9 POSTEC – unaxial research tester In the POSTEC – uniaxial tester, discussed
by Maltby and Enstad (1993), the sample is confined in a cylindrical die and wrapped
in a flexible membrane which is stretched between the outer periphery of the piston and
the inner perimeter of the lower part of the die. Since the membrane is stretched and in
contact with the wall and powder, the sample is compacted homogeneously; thus the wall
friction between the specimen and the die is reduced. Comparison of the POSTEC uniaxial
tester with a biaxial and Jenike-type shear cell testers, with the standardised CRM-116
limestone powder, indicated that the f c values obtained with the POSTEC are slightly less
than those obtained with Jenike-type shear cells and a biaxial tester. Since the total time for
Table 1.13 Comparison of shear and powder bulk data obtained from a Jenike shear cell and a Johanson
indicizer.
Jenike Johanson
2
Jenike shear cell
0
0 10 20 30 40 50
Major consolidation stress s1 (kPa)
Figure 1.28 Comparison of the degree of flowability from two shear cells and a cylindrical mould tester (Bell
et al. 1994).
one experiment is of the order of 20 minutes, this uniaxial tester should be considered to
have great potential for the measurement of the behaviour of powders in the stress region
of <100 kPa (Maltby et al. 1993).
1.7.4.10 Jenike and Johanson quality control tester The test apparatus consists of a
sample container, which has a small cylindrical section above a converging conical section,
mounted on a frame (Figure 1.29). Three different containers, all of the same height but of
Clamp
Plan view
Cover
Removable tray
Front elevation
Figure 1.29 Jenike and Johanson Quality Control Tester (JJQC) (Jenike and Johanson Inc).
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls December 21, 2007 21:17
different outlet sizes and conical section with different wall angles, are currently available.
These containers can be fitted through a hole in the top of the frame and are supported by a
flange at the top of the container. Below the outlet of the conical section, there is a perforated
slide gate, which allows air to pass through the powder within the container, but prevents
powdered material from leaving. A gasketed cover clamped to the top of the container forms
an airtight seal and has two fittings. An air supply is connected to one of the fittings and a
pressure gauge to the other fitting. These are subsequently connected to a control panel to
measure the air supply pressure and test pressure. The minimum recommended air supply
is circa 500 kN/m2 (60 psig).
About 4000 cm3 of aerated powdered material is gently filled into the container with the
smallest outlet situated on top of the closed perforated slide. The lid, connected to the air
supply and test gauge, is then clamped on top of the container and a specific pressure applied
for 30 seconds, to compact the powder. Pressure is then reduced to atmospheric pressure
and the perforated slide gate removed from the bottom of the conical section. Air pressure is
then increased until the arch, formed in the outlet, fails and the powdered cohesive material
flows from the container at a recorded pressure.
The consolidation and failure process can then be repeated for a minimum of four times.
The entire stepwise process can be repeated at different values of consolidation pressure.
This tester is designed for cohesive materials so a limit is placed on the maximum particle
size of powder used in the tester. Tests can be conducted at both ambient temperature and
humidity or under conditions created in an environmental chamber. Tests conducted with
the Jenike and Johanson Quality Control Tester (JJQC) have been compared with results
obtained from a conventional Jenike shear cell tester using cohesive titanium dioxide,
laundry detergent, baking soda and table salt. A plot of the ‘failure’ pressure obtained from
the JJQC tester and the Jenike shear cell tester strength showed that the JJQC test values
are significantly lower at high consolidation pressures but were comparable to the Jenike
values at low consolidation pressures (Ploof & Carson 1994).
Tests with ‘dry’ limestone dust (0.07% moisture) and with 0.35% and 1.36% moisture
added showed that as the percentage of moisture in the powder increased the average failure
and thus the cohesiveness of the material increased.
Plinke et al. (1994) investigated the dependence of cohesion on moisture content, parti-
cle size distribution and the melting temperature of materials. Four industrial materials
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls December 21, 2007 21:17
were chosen – titanium dioxide, limestone reference powder (CRM116), glass beads and
lactose – with a range of sizes −d < 5 μm, 5 < d < 25 μm and d > 25 μm – and tested
for cohesiveness over a range of moisture values of 0–6% w/w.
The base or zero value of the moisture content of the material was taken as a ‘as received
material’ condition. The actual moisture content of each material was determined at the
time of the test by averaging the moisture measurement taken before and after the test to
account for any moisture lost to, or taken up from, the environment during the test.
Comparison of the results showed that with the Jenike shear cell test, higher cohesion
values were obtained when the powder beds were compacted at 6 kPa than when the powder
beds were compacted at 3 kPa. The Jenike shear cell test gave a higher cohesion value, when
compacted at 6 kPa, than that with the Peschl rotational split level shear test compacted at 5
kPa. The higher cohesive values being attributed to an increase in contact points and binding
forces. The moisture content increased the cohesion for limestone. The materials titanium
and glass beads behaved in a similar manner. Since titanium and glass beads do not adsorb
water the increase in cohesion must be due to the increase in the thickness of the liquid film
surrounding the non-wetted particles resulting in an increase in capillary binding forces
between particles; a phenomenon seen in the process of granulation and agglomeration.
The lactose powder was relatively unaffected, in terms of cohesion, by moisture. These
observations showed that cohesion, C, may be dependent upon the material factors of
r Moisture content – M (%)
r Mass median diameter – d50
r Melting temperature – Tm
r Voidage – e
r Specific surface area – BET (m2 /g)
r MOHS material hardness – MOHS
to postulate the algebraic relationship
−0.2
C = e1.2 M 0.2 d50 Tm0.3 (1.12)
The statistical confidence of this correlation can be quantified knowing that this relationship
showed a coefficient of correlation of R 2 = 0.67.
Inclusion of the specific surface areas of the powders and the Mohs hardness of the
particles into the above correlation increased the coefficient of correlation, R 2 , from 0.67
to 0.69 which illustrated an increase in reliability.
The relationship of cohesion with particle size was found to be
−0.6
C = 1.25 d50 (1.13)
which can be allied to the shear flowability index of the Warren Spring correlation between
cohesion and tensile strength derived by Farley and Valentin (1967/68).
100
Solvay CaCO3
40
Sturge CaCO3
20 Calcite
10 Zinc dust
Alumina
4
Cohesion 2
1
0.4
0.2 C = 27
0.1
0.04
0.02
0.01
0.01 0.04 0.1 0.4 1 2 4 10 20 40
Tensile strength
Figure 1.30 Relationship between cohesion and tensile strength for a range of industrial powders (Farley &
Valentin 1967/68).
(Figure 1.30). This relationship has also been confirmed for pharmaceutical intermediates
and products by Eaves and Jones (1971) and Pilpel and Walton (1974) (Figure 1.31).
It is now believed, however, that more powder flow properties can be incorporated into
this simple relationship of C = 2T . Incorporation of the parameters of particle size, bulk
and powder densities leads to the relationship expressed as the Warren Spring equation
τ n σ
= +1 (1.14)
C T
where n = 1 + (0.53/d 2/3 ) and T = A(ρb /ρp )m ; d is the volume/surface mean diameter,
ρb the bulk density of powder, ρp the particle density, m is an index relating T , the tensile
strength, to packing density and A is a constant.
The shear flowability index, n, was found, from past observations (Farley & Valentin
1965, 67/68), to be independent of the bulk density of sheared compacted powder. Because
of this independence of particle size from bulk density it is now realised that the shear
flowability index, n, from the Warren Spring equation and the Jenike internal angle of
friction may be the preferred parameters to characterise and quantify the flowability of
powders. Jenike and others (Williams et al. 1970/71; Williams & Birks 1965; Hill & Wu
1996; Cox & Hill 2004) selected the Jenike failure function to be one of the best indicators
to predict the ease of powder movement and powder flowability.
Rajendran Nair et al. (1990, 1993) examined the cohesiveness of mixtures of a coal and
10% clay mix, which had a residual moisture content of 0.15% moisture, with mixes having
various amounts of added water. The parameter of cohesiveness (Cm ) was derived from the
yield loci measured in a Jenike shear cell tester and the tensile strength measured was from
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls December 21, 2007 21:17
9.0
5.0
1 1.5 5 10
Cohesion (C. g/cm2)
Figure 1.31 Relationship between cohesion and tensile strength for pharmaceutical powders (Pilpel & Walton
1974).
a split cell tester (Hosokawa Micron cohetester). As the percentage of moisture increased
from 0 to 15% w/w, both the cohesiveness and the shear stresses increased (Figure 1.32).
From the initial linear part of these series of yield loci, Rajendran Nair and co-workers
calculated the internal friction, φRN , from the slope of the yield loci and also computed the
tensile strength, TRN , from the extrapolated yield loci of the coal–clay–water mixtures, to
arrive at the relationship:
Cm
TRN = (1.15)
φRM
Direct measurements of tensile strengths of the coal–clay–water mixtures obtained from
the Hosokawa Micron cohetester, TH , were then compared with those obtained from the
extrapolated Jenike yield loci to propose the linear relationship:
TRN = 1.5 TH−0.5 (1.16)
Yamatmoto (1990) also used a Hosokawa cohetester to investigate the tensile strength of
sub-micrometre limestone and silica when exposed to various relative humidities and found
an increase in tensile strength at different degrees of packing or bed porosity.
Yokoyama et al. (1982) measured the tensile strength with the swing method of the
Hosokawa cohetester, for a range of particle sizes (1–90 μm) of different densities (0.928–
6.01 g/cm3 ) over a range of moisture percentages (0.06–15.2% w/w), to evaluate the po-
tential floodability of powders. Yokoyama et al. defined their dimensionless floodability, as
opposed to Carr’s definition of flowability, as the ratio of the cohesive force (C) – measured
by cohetester – to the gravity force on particles (m p g).
C 3T
= (1.17)
mpg (1 − ε)dp ρg
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls December 21, 2007 21:17
20
10
fc
0 10 20 30 40
Normal stress (N/m2)
Figure 1.32 Rajendran Nair data of shear stress versus normal stress for coal–water mixtures (Rajendran
Nair et al. 1990).
where T is the tensile strength of a powder bed; dp is the particle diameter; ε is voidage of
the bed and ρ is the particle density.
Figure 1.33 shows the calculated dimensionless term C/(m p g) versus the ratio ρb /ρav
where ρb is the bulk density of the bed and ρav is the arithmetic average of aerated and
packed densities of the powder.
106
(−)
BaTiO3
CaCO3
0.26%
Clay Moisture content on
C/mp g
W.A.
Lactose
C.M.C.
103
Polyethylene
102
0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6
ρb/ρav
(−)
Figure 1.33 Yokoyama et al. (1982) data for the potential floodability of powders.
Kurz and Minz (1975) investigated the flowability of powders in terms of the relationship
between the unconfined yield strength, f c , and the major consolidation, σ1 – the failure
function of Jenike — for different-sized limestone powders (3.1–55.0 μm) having either
a narrow or a wide particle size distribution. The width of the distribution was defined by
a variation coefficient, Cv, where Cv = σstat /x1.3 , with σstat as the standard deviation of
the particle size profile and x1.3 the average particle size of the number–volume diameter
distribution of the limestone particles. A narrow distribution was considered to have a Cv
< 0.5 while a wide distribution had a Cv > 0.5.
It was concluded that average particle size was not the only criterion, which could be used
to characterise the cohesiveness of powders, but also the spread of particle sizes in a size
distribution was also a significant contributory factor. Limestone powders, with average
sizes above 8 μm and a narrow size distribution freely flowed but with the same-sized
limestone particles which had a wide distribution, cohesive flow behaviour existed.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls December 21, 2007 21:17
70
(−)
60
Floodability
50
40
30
102 103 104 105
C/mp g (ρb/ρav = 1.0) (−)
Figure 1.34 Similarity between Carr’s floodability factor (Carr 1965b,c) and Yokoyama et al. parameter,
C/m p g (Yokoyama et al. 1982).
The shape of particles is now regarded as having as much influence upon the mechanical
properties, the degree of flowability and the cohesiveness of powders as particle size.
Pilpel and Walton (1974) and Walton and Pilpel (1972a,b) measured the shear and tensile
properties of differently shaped materials and moisture (Pilpel 1970) to assess their failure
and flow behaviour into various filling and storage units.
1.8.3 Overview of the instrumentation and techniques available for the determination of
bulk powder properties
In a survey of the various bulk powder tests developed and in use for the determination of
the failure properties and measurement of the degrees of flowability of powders, Schwedes
(2003) indicated that the equipment available varied from highly theoretical and technical
instrumentation to very simple empirical techniques.
The choice given to the production engineer or research powder technologist is thus
dependent upon the level of information required. In the design of mass flow hoppers there
tends to be a greater need for knowledge on yield loci, stresses and failure criteria than that
possibly needed for routine powder quality control.
The instrument and technique which may be chosen is also governed by the type of bulk
solid (which may range from free flowing to very cohesive) undergoing investigation and
also the frequency of information needed, cost of the device, time and skill allocated for the
test together with the availability of equipment for the measurement of both particle and
bulk solids characteristics.
Table 1.15, taken from the work of Schulze (1995, 1996a,b), indicates a wide range of
apparati and protocols to measure a powder yield strength or a (Jenike) failure function for
use in the determination of bulk powder flowability.
P1: SFK/RPW
60
BLUK141-McGlinchey.cls
Table 1.15 Overview of the various methods for the characterisation of the flowability of bulk solids.
P2: SFK/RPW
Flowability testers Figure Criterion 1 Criterion 2 Criterion 3 Criterion 4 Criterion 5 Criterion 6 Criterion 7
Uniaxial columns
Procter & Gamble caking tester 1.25 / /no
J & J Quality control tester 1.29 / no/no
Johanson Hang-up indiciser 1.27 / no/no
Monoaxial tester / /no
Penetration test / /no
BULK SOLIDS HANDLING
σ3
σn
σ1 σ1
σ3
Figure 1.35 Difference between direct and indirect shear testers. (Jenike direct shear tester inside square and
biaxial tester solid rectangle.)
Direct and indirect shear stress equipment is usually limited to research projects because
of the expense, the skill and time evolved to determine the yield loci and failure functions of
particulate materials from bi- and tri-axial shear testers. The designation of which type of
shear tester has been used may be defined by the location of the shear failure zone. With
direct shear testers – Jenike type – the major principal stress rotates during shear (Figure
1.35), whilst with indirect shear testers – tri- and bi-axial – the directions of the principal
stresses are fixed and orientated in either three or two dimensions, respectively, and remain
constant during the test.
The Jenike (or Standard Shear Tester) tester together with commercially available ring
and torsional shear testers are, however, relatively easier to use than the tri- and bi-axial
shear testers. In some cases ring, torsional and the Standard Shear Tester (Jenike) are now
automated and computer controlled for ease of use and speed of determination. These
instruments measure parameters for use in mass flow hopper design and calculation of
critical hopper outlet diameters needed to ensure mass flow as opposed to plug or ‘rat-
holing’ flow (Hill & Cox 2002). A simple approach for the determination of flow from an
orifice can, however, be achieved with either a Flodex (Hanson Research Corporation), a
Jenike and Johanson Quality Control Tester or a ‘home made’ model (Figures 1.16, 1.29,
1.9 & 1.15). The uniaxial and monoaxial tester approach relies upon the formation of a
column of powder, either constrained or freestanding, to measure an unconfined yield shear
stress together with the normal consolidation stress to give a failure function. The uniaxial
tester, with a vertically applied failure stress, should have an L/D ratio greater than 2 in
order to achieve accurate unconfined stresses. The monoaxial tester, which is sheared in a
horizontal direction, does not have this limitation. Column formation and subsequent failure
are relevant to the simple, rapid results and user-friendly equipment seen with the Johanson
hang-up indicizer, caking or tackiness testers. Cohesion and tensile strength are also of
great importance to the production powder technologist or plant engineer. Tensile strength
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls December 21, 2007 21:17
cannot, however, be directly measured by Jenike and ring-type shear cells. This lack has been
overcome by the development of the WSL tensile tester (Ashton et al. 1964, 1965; Farley
& Valetin 1967/68) and the Hosokawa cohetester split cell tensile tester. Although cohesion
and adhesion may be evaluated from a shear stress versus compaction stress relationship,
the Warren Spring-Bradford tester (Orband & Geldart 1997) has now been marketed as the
Ajax (Bolton) cohesion tester, a dedicated instrument for cohesion measurement.
The simplest method to indicate the flowability of bulk powders is to use any technique
that measures the static angle of a heap of powder – angle of repose – using either the Carr’s
angle of repose equipment (Figure 1.9) or a simple apparatus (Figure 1.15). A dynamic
angle of repose can now be measured with an Aero-Flow Analyzer.
Schulze judged the acceptance of testers for various research and industrial problems by
highlighting the different shear approaches and the various types of bulk powder testers
available, based on seven criteria. These criteria are numerated in Table 1.15:
1 The ability to compact or consolidate the powder, in a movable cell which, with
subsequent horizontal shear measures the powder failure or yield strength.
2 Maintenance of an applied normal consolidation stress whilst undergoing shear to
steady state flow.
3 To ensure mass flow in any hopper design the direction of the major principal stress
during steady state flow should coincide with the direction of failure of the powder
along the hopper wall.
4 Reproducible stress conditions on the bulk solid sample both at compaction (consol-
idation) and failure illustrated as ‘item/item’.
5 Knowledge that average stresses and uniform stress distribution, to ensure no
anisotropy at the compaction plane and at the failure plane, is achievable.
6 Possibility to vary the magnitude of the consolidation stress applied to the powder
sample.
7 Possibility for the measurement of shear on ‘time consolidated’ samples.
Possibly the most important criteria for quality control, flowability and bulk powder handling
are the items highlighted under numbers 1, 4, 6 and 7.
Scrutiny of the type of instrumentation, which has been used in the diverse field of
bulk powder handling and outlined in this chapter, should allow personnel in the many
industries which produce, handle and package powders, an opportunity to select one or
more instruments and techniques which may aid the prevention of some of the production
problems which could arise from day to day.
References
Abdelkarim, A.M. (1982) Shear and normal stresses in uniaxial compaction. Ph.D. thesis, University of Bradford,
Bradford, UK.
Adhikari, B., Howes, T., Bhandari, B.R. & Truong, V. (2001) Stickiness in foods: a review of mechanisms and
tests methods. Int. J. Food Properties, 4(1), 1–33.
Adler, A. (1969) Flow Properties of Metal Powders. Int. J. Powder Metallurgy, 5(1), 7–20.
AJAX Equipment (Bolton) Ltd. Milton Works. Mule St, Bolton, Lancashire. www.ajax.co.uk.
Akers, R.J. (1992) Certification of a Limestone Powder for Jenike Shear Testing. CRM116. Commission
of European Committees, BCR, Office for Official Publications of the European Communities, Brussels,
Luxembourg.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls December 21, 2007 21:17
Archard, J.F. (1953) Contact and rubbing of flat surfaces. J. Appl. Phys., 24(8), 981–988.
Archard, J.F. (1957) Elastic deformation and laws of friction. Proc. R. Soc., A243, 190–205.
Ashton, M.D., Farley, R. & Valentin, F.H.H. (1964) An improved apparatus for measuring the tensile strength of
powders. J. Sci. Instum., 41, 763–765.
Ashton, M.D., Cheng, D.C-H., Farley, R. & Valentin, F.H.H. (1965) Some investigation into the strength and
flow properties of powders. Rheol. Acta, 4(3) 206–218.
ASTM B329-98 (2003) Apparent Density of Metal Powders. American Society for Testing Materials, Interna-
tional, West Conshohocken, PA. www.astm.org.
ASTM B855-06. Arnold Meter & Hall Funnel. American Society for Testing Materials, International, West
Conshohocken, PA. www.astm.org.
ASTM D 4180-03. Hall Test Cup Method. American Society for Testing Materials, International, West Con-
shohocken, PA. www.astm.org.
ASTM D 6393-99 (1999) Carr Flowability Indices. American Society for Testing Materials, International, West
Conshohocken, PA. www.astm.org.
ASTM D 6773-02. Standard Shear Test Technique. American Society for Testing Materials, International, West
Conshohocken, PA. www.astm.org.
ASTM eStandardsStore at www.webstore.ansi.org.
Bell, T.A., Ennis, B.J., Grygo, R.J. et al. (1994) Practical evaluation of the Johanson hang-up indicizer. Bulk
Solids Handling, 14(1), 117–125.
Beverloo, W.A., Leniger, H.A. & van de Velde, J. (1961) The flow of granular solids through orifices . J. Chem.
Eng. Sci., 115, 260–269.
Bishop, A.W. & Green, G.E. (1965) The influence of end restraint on the compression strength of cohesiveless
soils. Geotechnique, 15, 243–266.
Bockstiegel, G. (1966) Relations between pore structure and densification mechanism in the compacting of iron
powder. Int. J. Powder Met., 2, 13.
Boden, J. (1981) The tensile strength and anisotropy of powder compacts. Ph.D. thesis, University of Bradford,
Bradford, UK.
Bodhmage, A. (2006) Correlation between physical properties and flowability indicators for fine powders. M.Sc.
thesis, University of Saskatchewan, Saskatchewan, Canada.
Briscoe, B.J, Pope, L, Adams, M.J. (1984) Interfacial friction of powders on concave counterfaces. Powder
Technol. 37, 169–181.
British Standards at www.bsonline.bsi-global.com
Brown, L. & Richards, J.C. (1970) Principles of Powder Mechanics. Pergamon Press, London.
BS 1377-7 (1990) Methods of Tests for Civil Engineering Puposes. Shear Strength Tests (Total Stress). British
Standards Institution (BSI), Gunnersbury, London, UK.
BS 2955 (1993) Glossary of Terms Relating to Particle Technology. BSI, Gunnersbury, London, UK.
BS 4140-9 (1986) Methods of Test for Aluminium Oxide. Measurement of Angle of Repose. BSI, Gunnersbury,
London, UK.
BS 4140-23 (1987) Methods of Test for Aluminium Oxide. Determination of Absolute Density Using a Pyknometer.
BSI, Gunnersbury, London, UK.
BS 4359: Pt 2 (1982) Determination of Specific Surface Area of Powder. Permeametry & the Kozeny–Carman
Equation. BSI, Gunnersbury, London, UK.
BS EN 543 (2003) Apparent Density of Powder and Granulues. BSI, Gunnersbury, London, UK.
BS EN 725-8 (1997) Bulk Tapped Density of Ceramic Powders. BSI, Gunnersbury, London, UK.
BS EN 993-17 (1999) Density of Dense, Shaped Refractory Products by Mercury Methods. BSI, Gunnersbury,
London, UK.
BS EN 1097-3 (1998) Bulk Density of Loose Aggergates. BSI, Gunnersbury, London, UK.
BS EN 23923-2 (1993) Apparent Density of Metallic Powders. BSI, Gunnersbury, London, UK.
BS EN ISO 7837 (2001) Bulk Density of Loose Fertilizers. BSI, Gunnersbury, London, UK.
Carman, P.C. (1937) Fluid flow though granular beds. Trans. Inst. Chem. Eng., 50, 150–166.
Carr, R.L. (1965a) Angle of repose. Chem. Eng., 18(1), 163–169.
Carr, R.L. (1965b) Classifying flow properties of solids. Chem. Eng., 72, 69–72.
Carr, R.L. (1965c) Evaluating flow properties of solids. Chem. Eng., 72(2), 163–169.
Carson, J.W. & Marinelli, J. (April 1994) Characterize bulk solids to ensure smooth flow. Chem. Eng., 101(4),
78–90.
Clift, R. (1985) Particle-particle interactions in gas-particle systems. Powtech. 85. No. 91. Institution of Chemical
Engineers, Rugby, UK.
Cowherd, C., Grelinger, M & Englehart, P.J. (1989) An Apparatus and methodology for predicting the dustiness
of materials. Am. Ind. Hyg. Assoc. J., 50, 123–130.
Cox, G.M. & Hill, J.M. (2004) The limiting ideal theory for shear-index cohesionless granular materials. ANZIAM
J. 45, 373–392.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls December 21, 2007 21:17
Davidson, J.F. & Nedderman, R.M. (1973) The hour-glass theory of hopper flow. Trans. Inst. Chem. Eng., 51,
29–35.
Davidson, J.F., Nedderman, R.M. & Walker, D.M. (1966) An approximate theory for pressures and arching in
hoppers. Chem. Eng. Sci., 21, 975.
DIN 5599-2 (1999) Standardised Single-Drop Dustiness Apparatus to Generate a Dustiness Index of Fillers and
Pigments. Deutsches Insitut fur Normung, Berlin, Germany. www2.din.de.
Eaves, T. & Jones, T.M. (1971) Cohesion and tensile strength of bulk solids. Rheol. Acta, 10(1), 127–134.
EN 23923 (1992) Scott Volumeter. BSI, Gunnersbury, Middlesex, UK.
Endersby, V.A. (1942) Fundamental research in bituminous stabilization. Proc. Highway Res. Board, 22, 442–
459.
Engelsmann, J. Ludwigshafen, Str 137-141, D-67059. Ludwigshafen am Rhein, Germany. www.engelsmann.de/.
Enstad, G.G. & Maltby, L.P. (1992) Flow property testing of particulate solids. Bulk Solids Handling, 12, 451.
Ergun, S. (1952) Fluid flow through packed columns. Chem. Eng. Prog., 48, 89–94.
Ergun, S. & Orning, A.A. (1949) Fluid flow through randomly packed columns and fluidized beds. Ind. Eng.
Chem. Fundamentals, 41, 1179.
Farley, R. & Valentin, F.H.H. (1965) Problems associated with storage hoppers. Trans. Inst. Chem. Eng., 43,
T193–198.
Farley, R. & Valentin, F.H.H. (1967/68) Effect of particle size upon the strength of powders. Powder Technol.,
1, 344–354.
Flodex. Hanson Research Corporation, Chatsworth, CA. USA www.hansonresearch.com and Acil Sarl, 1, place
de Gaulle 78400 Chatou, France.
Freeman Techology, Worcestershire, UK. www.freemantech.co.uk.
Geldart, D. (1972) The effect of particle size and size distribution on the behaviour of gas-fluidised beds. Powder
Technol., 6, 201–215.
Geldart, D. (1990) Estimation of basic particle properties for use in fluid–particle process calculations. Powder
Technol., 60, 1–13.
Geldart, D. (2005) The characterisation of bulk powders. In: Characterisation of Bulk Solids (ed D. McGlinchey).
Blackwell Publishing, Oxford, UK.
Geldart, D., Harnby, N. & Wong, A.C. (1984) Fluidization of cohesive powders. Powder Technol., 37, 25–37.
Gerritsen, A.H. (1986) A Simple Method for Measuring Powder Flow Functions with a view to hopper design.
Partec ‘86. Nuremberg, Germany, Part 3, pp. 257–279.
Gerritsen, A.H. (1990) Proc 2nd World Congress Particle Technology, Kyoto, Japan, Part 1, pp. 61–70. [See
Schulze, J.]
Hamelmann, F. & Schmidt, E. (2003) Methods of dustiness estimation of industrial powders – a review. KONA
Powder Part., 21, 7–18.
Hamelmann, F. & Schmidt, E. (2004) Methods for characterizing the dustiness estimation of powders. Chem.
Eng. Technol., 27, 844–847.
Hartley, P.A. & Parfitt, G.D. (1984) An improved split-cell apparatus measurement for the measurement of tensile
strength of powders. J. Phys. E Sci. Instrum., 17, 347–349.
Harwood, J. (1971) Compaction effect on flow property indexes for powders. J. Pharm. Sci., 60, 161–3.
Hausner, H.H. (1966) Proceeding Conference Particle Size Analysis. Society for Analytical Chemistry, London.
Hausner, H.H. (1967) Friction conditions in a mass of metal powder. Int. J. Powder Met., 3(4), 7–13.
Hertz, H. (1882) Uber die Beruhrung fester elastischer kurper – On the contact of elastic solids, pp. 146–162
and Uber die Beruhrung fester elastischer kurper und uber die harte – On the contact of elastic solids and on
hardness, pp. 163–183 from Miscellaneous Papers by H. Hertz (English translation, eds D.E. Jones & G.A.
Schott) 1986. Macmillian, London.
Hill, J.M. & Cox, G.M. (2002) Rat-hole stress profiles for shear-index granular materials. Acta mech., 155, (3-4).
157–172.
Hill, J.M. & Wu, Y-H. (1996) The punch problem for shear-index granular material. J. Mechanics & Applied
Mathematics, 49, (1) 81–105.
Hosokawa Micron Ltd. Runcorn, Cheshire, UK. www.hosokawa.co.uk.
Ileleji, K.E. (2005) Report on Investigation of methods to improve the flowability of distillers dried grains. Agri
& Biological Dept., Purdue University, USA.
ISO 902 (1976) Angle of Repose for Alumina. International Organisation for Standardisation, Geneva.
ISO 3923 Part I Flowability. International Organisation for Standardisation, Geneva.
ISO 3923-1 (1979) Apparent Density Funnel Method. International Organisation for Standardisation, Geneva.
ISO 3923-2 (1981) Scott Volumeter. International Organisation for Standardisation, Geneva.
ISO 4324 (1977) Angle of Repose for Powders and Granules. International Organisation for Standardisation,
Geneva.
ISO 4490 (2000) Hall Flowmeter. International Organisation for Standardisation, Geneva.
ISO 6770 (1982) Flowability & Bulk Density of Tea. International Organisation for Standardisation, Geneva.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls December 21, 2007 21:17
ISO 8398 (1989) Angle of Repose for Fertilers. International Organisation for Standardisation, Geneva.
ISO www.iso.org.
ISO/TC 17892-5 (2004) Geotechnical investigation and testing. Laboratory testing of soil – Part 5: Incremental
loading oedometer test.
Jenike, A.W. (1964) Storage and Flow of Solids Bulletin 123, 1st edn. University of Utah, Salt Lake City, USA.
[See also (1970), 6th edn.]
Jenike & Johanson Inc. Tyngsborough, MA, USA. www.jenike.com.
Johanson, J. (1965) The use of flow-corrective inserts in bins. Trans. ASME., 232, 69–80.
Johanson, J.R. (1992) The Johanson Indicizer System vs. the Jenike Shear Tester. Bulk Solid Handling, 12(April–
June), 273–240.
Johanson, J.R. (29 December 1987) Bulk Solids Property Tester. U.S. Patent 4715212.
Kaye, B.H., Faddis, N. & Gratton-Liimataienen, J. (May 1997) Characterising the flowability of a powder using
avalanching studies. Proc. Powder & Bulk Solids Exhibition, Chicago, IL, pp. 123–133.
Kaye, B.H., Gratton-Liimatainen, J. & Faddis, N. (1995) The effect of flow. Agents on the rheology of plastic
powders. Part. Part. Syst. Charact., 12, 232–236.
Kendall, K. (1986) Flocculation clustering and weakness of ceramics. Nature, 319, 203–205.
Kendall, K., Alford, McN. & Birchall, J.D. (1971) Elasticity of particle assembles as a measure of the surface
energy of solids. Proc. Roy. Soc., A324, 301.
Kesler, C.E. (1959) Effect of length to diameter (L/D) ratio on compressive strength. Proc. ASTM, 59, 1216–
1229.
Knight, P.C. & Johnson, S.H. (1988) Measurement of powder cohesive strength with a penetration test. Powder
Technol., 54(4), 279–283.
Kostelnik, M.C. & Beddow, J.K. (1970) Modern Developments in Powder Metallurgy, Vol. 4 (ed H. Hauser).
Plenum Press, New York, pp. 29–48.
Kostelnik, M.C., Kludt, F.H. & Beddow, J.K. (1968) The initial stage of compaction of metal powders in a die.
Int. J. Powder Metallurgy, 4(4), 19–28.
Kurz, H.P. & Minz, G. (1975) The influence of particle size distribution on the flow properties of limestone
powders. Powder Technol., 11, 37–40.
Labuza, T.P. (2002) Rapid Testing Symposium. Paper on Prediction of Caking. Procter and Gamble, Cincinnati,
OH, USA.
Lappas, L. & Dempski, R.E. (1965) Pharmaceutical sciences – 1964. A literature review. J. Pharm. Sci., 54(7)
931–958.
Lee, Y.S.L., Poynter, R., Podezeck. F. & Newton, J.M. (2000) Development of a dual approach to assess powder
flow from avalanching behaviour. AAPS Pharm. Sci. Tech., 1(3), article 21.
Lyons, C.P. & Mark, D. (1992) HSE Contract Research Report 40. Warren Spring Laboratory, Stevenage,
Hertfordshire, UK.
Lyons, C.P. & Mark, D. (1994) HSE Contract Research Report 62. Warren Spring Laboratory, Stevenage,
Hertfordshire, UK.
Maltby, L.P. & Enstad, G.G. (1993) Uniaxial tester for quality control and flow property characterisation of
powders. Bulk Solids Handling, 13, 135.
Maltby, L.P., Enstad, G.G. & de Silva, S.R. (1993) Measurements from the flexible-boundary biaxial tester. Proc.
Powder & Bulk Solid Conference. Reed Exhibition Company, London, UK, pp. 15–27.
Marjanovic, J., Geldart, D. & Orband, J.L.R. (1998) Review on testers for measuring flow properties of bulk
solids. World Congress Particle Technology 3, Brighton, UK. CD-Rom Institution of Chemical Engineers,
George E Davis Building, Railway terrace, Rugby, UK, pp. 167–171.
Marjanovic, J., Geldart, D., Orband, J.L.R. & Mooney, T. (1995) Partec 95 (Janssen Centennial). Nurenberg,
Germany, pp. 69–78.
McGee, E. (August 2006) Powder behaviour. Solid Bulk Handling, 12–14.
McGlinchey, D. & McGee, E. (July 2005) A multifaceted approach to characterising powders for flow. 7th World
Congress of Chemical Engineering, 10–14 July 2005, Glasgow, Scotland.
Molerus, O. (1980) A coherent representation of pressure drop in fixed beds and of bed expansion for particulate
fluidized beds. Chem. Eng. Sci., 35(6), 1331–1340.
Molerus, O. (1982) Interpretation of Geldart’s Type A, B, C and D powders taking into account interparticle
cohesion forces. Powder Technol., 33, 81–88.
Monick, J.A. (May 1966) Alcohols: Their chemistry, properties and manufacture. Proc. Chem. Manufact., 108–
112.
Nedderman, R.M. & Laohakal, C. (1980) The thickness of the shear zone of flowing granular materials. Powder
Technol., 25, 91–100.
Novosad, J. (1990) Proc. 2nd World Congress Particle Technology. Kyoto, Japan, Part 1, p. 54; Part 111, p. 167.
Orband, J.L.R. & Geldart, D. (1997) Direct measurement of powder cohesion using a torsional device. Powder
Technol., 92(1), 25–33.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls December 21, 2007 21:17
Peck, R.B. & Gholamriza, M. (1996) Theoretical Soil Mechanic in Engineering Practice. J. Wiley & Sons, Inc.
Corporate Headquarters, NJ.
Peschl, I.A.S.Z. (1988) Mechanical properties of powders. Bulk Solids Handling, 8(5), 615–624.
Peschl, I.A.S.Z. (1989) Equipment for the measurement of mechanical properties of bulk powders. Powder
Handling Process., 1(1), 73–81 and Quality control of powders for industrial application. Powder Handling
Process., 1(4), 357–368.
Peschl, I.A.S.Z. & Colijn, H. (1977) New rotational shear testing technique. J. Powder Bulk Solid Technol., 1,
55–60.
Pilpel, N. (April 1970) Some effects of moisture on the flow and cohesiveness of powders. Manuf. Chem. Aerosol
News., 41, 19–22.
Pilpel, N. & Walton, C.A. (1974) The effect of particle size and shape on the flow and failure properties of
procaine penicillin powders. J. Pharm. Pharacol., 26, lP–l0P.
Plinke, M.A.E., Leith, D., Hathaway, R. & Loffer, F. (1994) Cohesion in granular materials. Bulk Solids Handling,
14(1), 101–106.
Ploof, D.A. & Carson, J.W. (1994) Quality control tester to measure relative flowability of powders. Bulk Solids
Handling, 14(1), 127–132.
Powder Research Ltd, Harrogate, UK.
Prescott, J.K. & Barnum, R.A. (2000) On powder flowability. Pharm. Technol., 24(10), 60–84.
Rajendran Nair, P.B., Ramanujan, T.K. & Ramanujam, M. (1990) Proc. 2nd World Congress Particle Technology.
Kyoto, Japan, Part 1, pp. 124–133.
Rajendran Nair, P.B., Ramanujan, T.K. & Ramanujam, M. (1993) Flow characteristics of raw coal fines. Adv.
Powder Technol., 4(4), 297–310.
Ridgway, K. & Tarbuck, K.J. (1968) Voidage fluctuations in randomly-packed beds of spheres adjacent to a
containing wall. Chem. Eng. Sci., 23(9), 1147–1155.
Rietema, K. (January–February 1984) Powders, what are they? Powder Technol., 37(1), 5–23.
Rietema, K. & Hoebink, J. (November–December 1977) Transient phenomena in fluidized beds when switching
the fluidizing agent from one gas to another. Powder Technol., 18(2), 257-265.
Riley, G.S., Mann, S. & Jesse, R.O. (1978) Angle of repose of cohesive powders. J. Powder Bulk Solids Technol.,
2(4), 15–18.
Roberts, T.A. & Beddow, J.K. (December 1968) Some effects of particle shape and size upon blinding during
sieving. Powder Technol., 2(2), 121–124.
Roscoe, K.H. (1970) 10th Rankine lecture. Geotechnique, 20, 122.
Roscoe, K.H., Schofield, A.N. & Wroth, C.P. (1958) On the yielding of solids. Geotechnique, 8, 22.
Savage, S.B. (September 1967) Gravity flow of a cohesionless bulk solid in a converging conical channel. Int. J.
Mech. Sci., 9(9), 651–659.
Schofield, A.N. & Wroth C.P. (1968) Critical State Soil Mechanics. McGraw Hill, New York.
Schofield, C. (1981) Dust generation and control in materials handling. Bulk Solids Handling, 1(3), 419–442.
Schulze, D. (1995) Zur Fließfähigkeit von Schüttgütern – Definition und Meßverfahren. Chem. Eng. Technol.,
67(1), 60–68 (in German). www.dietmar-schulze.de.
Schulze, D. (1996a) Flowability of bulk solids – Definition and measuring techniques, Part I. Powder Bulk Eng.,
10(4, Part 1), 45–61. [See Schwedes, J. (2003)]
Schulze, D. (1996b) Flowability of bulk solids – Definition and measuring techniques, Part II. Powder Bulk Eng.,
10(6, Part 11), 17–28. [See Schwedes, J. (2003)]
Schwedes, J. & Schulze, D. (1990) Proc 2nd World Congress Particle Technology. Kyoto, Japan, Part 1, pp. 61–70.
Schwedes, J. (1975) Shearing behaviour of slightly compressed cohesive granular materials. Powder Technol.,
11, 59–67.
Schwedes, J. (2003) Review on testers for measuring flow properties of bulk solids. Granular Matter, 5(1), 1–43.
www.texturetechnologies.com.
Schwedes, J. & Schulze, D. (1992) Letter to the editor: Measurement of flow properties of solids. Bulk Solids
Handling, 12(3), 454–455.
Seville, J.P.K. & Clift, R. (January–February 1984) The effect of thin liquid layers on fluidisation characteristics.
Powder Technol., 37(1), 117–129.
Stable Micro Systems. Surrey, UK. www.stablemicrosystems.com.
Standard Shear Testing Technique (SSTT) ASTM D6773-02. American Society for Testing Materials, Interna-
tional, West Conshohocken, PA.
Standard Shear Testing Technique for particulate solids using the Jenike shear cell (1989) Institution of Chemical
Engineers, George E Davis Building, Railway Terrace, Rugby, UK, pp. 167–171.
Stanley-Wood, N.G. (1983) Enlargement and Compaction of Particulate Solids. Butterworth, London.
Stanley-Wood, N.G. (1987) Uniaxial powder compaction. In: Tribology in Particulate Technology (eds B.J.
Briscoe & M.J. Adams). Adam Hilger, Bristol, UK.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls December 21, 2007 21:17
Stanley-Wood, N.G. (2000) Particle size analysis: introduction. In: Encyclopaedia of Analytical Chemistry:
Applicatons, Theory and Instrumentation, Vol. 6 (ed R.A. Myers). Wiley, Chichester, UK, pp. 5301–5337.
Stanley-Wood, N.G. (2005) Particle characterisation in bulk powders. In: Characterisation of Bulk Powders (ed
D. McGlinchey). Blackwell Publishing, UK.
Stanley-Wood, N.G. & AbdelKarim, A.M. (1982) J. Powder Metallurgy Int., 14, 135.
Stanley-Wood, N.G. & Abdelkarim, A.M. (1983a) Application of critical state to uniaxial compaction. Powder
Technol., 35, 185.
Stanley-Wood, N.G. & Abdelkarim, A.M. (1983b) Proc of RILEM/CNR Int. Symp on Principles & Applications
of Pore Structural Characterisation, Milan (eds J.M. Haynes & P. Rossi-Doria). Arrowsmith, Bristol.
Stanley-Wood, N.G., AbdelKarim, A., Johansson, M.E., Sadeghnejad, G. & Osborne, N. (1990) The variation
in, and correlation of, the energetic potential and surface areas of powders with degree of uniaxial compaction.
Powder Technol. 60, 15–26.
Stanley-Wood, N.G. & Johansson, M.E. (1980). Variation of intra- and inter-particle porosity with degree of
compaction. Analyst, 105, 1104–1112.
Stanley-Wood, N. & Sarrafi, M. (1988) Variations in, and relationships of surface area, internal angle of friction
and compact diametral fracture strength with degree of compaction. Particle & Particle Systems Characteri-
sation, 5(4), 186–192.
Stanley-Wood, N.G., Sarrafi, M., Mavere, Z. & Schaefer, M. (1993) The relationships between powder flowability,
particle-arrangements, bulk densities and Jenike failure properties. Adv. Powder Technol., 4(1), 33–40.
Stephens, D.J. & Bridgwater, J. (September–October 1978) The mixing and segregation of cohesionless partic-
ulate materials. Part I: Failure zone formation. Powder Technol., 21(1), 17–28.
Tamura, T. & Haze, H. (1985) Determination of the flow of granular materials in silos. Bulk Solids Handling,
5(3), 663–640.
TSI Instruments Ltd. High Wycombe, Buckinghamshire, UK. www.tsiinc.co.uk.
USP29-NF24 (2006) General Information Chapter ‘<1174> Powder Flow’. US Pharmacopeial Convention,
Rockville, MD, USA, p. 3017.
von Terzaghi, K. (1925) Erdhaumechanik auf Bodenphysikalischer Grundlage, Deuticke, Vienna.
von Terzaghi, K. (1943) Theoretical Soil Mechanic in Engineering. J. Wiley & Sons, Inc. Corporate Headquarters,
Hoboken, NJ.
von Terzaghi, K. & Peck, R.B. (1967) Theoretical Soil Mechanic in Engineering Practice, 2nd edn. J. Wiley &
Sons, Hoboken, NJ.
Walton, C.A. & Pilpel, N. (1972a) British Pharm. Conference, Keele, Paper 3.
Walton, C.A. & Pilpel, N. (1972b) The effects of particle size, shape and moisture content on the tensile properties
of procaine penicillin powders. J. Pharm. Pharmacol., 24(Suppl), 10P–16P.
Williams, J.C. & Birks, A.H. (1965) The preparation of powder specimens for shear cell testing. Rheol. Acta, 4,
170–182. Paper presented at a meeting of the British Society of Rheology, University of Nottingham, April
6–8, 1965.
Williams, J.C. & Birks, A.H. (December 1967) The comparison of the failure measurements of powders with
theory. Powder Technol., 1(4), 199–206.
Williams, J.C. (1977) The rate of discharge of coarse granular materials from conical mass flow hoppers. Chem.
Eng. Sci., 32(3), 247–255.
Williams, J.C., Birks, A.H. & Bharracharya, D. (September 1970/71) The direct measurement of the failure
function of a cohesive powder. Powder Techol., 4(6), 328–337.
Wong, A.C. (2000) Characterisation of flow by bulk density ratios. Chem. Eng. Sci., 55, 3855–3859.
Woodcock, C.R. & Mason, J.S. (1987) Bulk Solid Handling: An Introduction to the Practice and Technology.
Kluwer Academic Publishers, Dordrecht, The Netherllands.
Wouters, I.M.F. & Geldart, D. (1996) Characterising semi-cohesive powders using angle of repose. Part. Part.
Syst. Charact., 13, 254–259.
WSL Tensile Tester (March 1977) Chem. Eng., 161–164.
Yamatmoto, H. (1990) Relationship between adhesive force of fine particles and their dispersibility in gas. Proc.
2nd World Congress Particle Technology. Kyoto, Japan, Part III, pp. 167–173.
Yokoyama, T., Fujii, K. & Yokoyama, T. (1982) Measurement of tensile strength of a powder by a swing method
measuring instrument. Powder Technol., 32, 55–62.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 16, 2008 7:51
2 Hopper/bin design
JOHN W. CARSON
2.1 Fundamentals
Bins and silos are used to store bulk solids by virtually every industry around the world.
There are many confusing terms in bulk solids technology, beginning with naming the
storage vessel. To some people the term silo connotes a larger size vessel than a bin, but
what is larger – and therefore a silo – to one person could be small to another. Some refer to
the storage vessel as a tank, which at least avoids the distinction between a bin and a silo, but
to others this term is reserved for liquid storage. Further adding confusion are specialised
terms used in various industries. For example, grain storage vessels are often referred to as
an elevator, whereas in a coal-fired power plant the vessel is often called a bunker. Smaller,
usually portable, vessels often go by the name Tote R
or IBC.
To avoid confusion in this chapter, I will use the term bin as a general descriptor of a bulk
solids storage vessel of any size.
A bin can be divided into two major sections: cylinder and hopper (see Figure 2.1). The
cylinder section is that portion of the vessel that has constant cross-sectional area over
its height, i.e. vertical sidewalls. Note that by this definition a cylinder is not necessarily
circular, although this is the most common shape used for bins.
In contrast to the cylinder section, a hopper has changing cross-sectional area over its
height. In most cases the hopper is converging, so its cross-sectional area is smaller at the
bottom than at the top. However, some hoppers used to store poorly flowing materials such
as wood chips have a diverging geometry.
In most industrial situations a feeder is used to control discharge from a hopper outlet.
Control involves not only stopping and starting flow but also metering the rate of discharge.
It is important to note that a feeder is quite different from a conveyor in terms of operation.
A conveyor simply transports material from one location to another, so essentially whatever
mass per unit time enters it comes out at the discharge end. Thus, a conveyor provides no
ability to meter or control the throughput rate, but a feeder does since it is flood-loaded.
This distinction is important in terms of design of a feeder.
Bins vary tremendously in size, from ones that store only a few kilograms of material
to those with storage capacities in excess of 10 000 metric tonnes. The range of discharge
rates can similarly vary from a few grams per minute to several thousand tonnes per hour.
Bins are typically used to store incoming raw materials, intermediate products as part
of the manufacturing process and/or outgoing products to be shipped to customers. The
most common function of a bin is to provide surge capacity to compensate for effects of
changes in production rate or frequency, and variations in rate or frequency of incoming or
outgoing shipments. Another somewhat less common but still important function of a bin
is to process, condition, age or blend the bulk solid stored therein.
Bins can be very problematic, resulting in increased cost of plant operation, low product
yield, extended time to market with new products, quality/product performance problems
68 Bulk Solids Handling: Equipment Selection and Operation Edited by Don McGlinchey
© 2008 Blackwell Publishing Ltd. ISBN: 978-1-405-15825-1
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 16, 2008 7:51
HOPPER/BIN DESIGN 69
and safety and health issues. Typical problems include process stoppages, feed rate and
process control issues, and product quality concerns due to particle segregation, attrition,
degradation or buildup. Other common problems are: difficulty in properly cleaning the
vessel, difficulty of dust containment and shortened equipment life due to wear, corrosion
or inadequate structural integrity.
Many injuries and several deaths associated with bins occur each year. Sometimes these
are the result of structural failure caused by the stored bulk solid applying loads to the vessel
walls that they were not designed to withstand. Collapsing arches or ratholes, or falling into
a bin and becoming engulfed in the bulk solid, can also cause serious injury or death. In
addition, injuries may occur while poking on moving parts inside a feeder or swinging a
mallet to encourage flow.
Two primary flow patterns can develop when a bulk solid discharges from a bin: funnel flow
and mass flow. Funnel flow, also called core flow, is defined (Jenike 1964) as a flow pattern
in which some material is stationary while the rest is moving (see Figure 2.2). According to
Figure 2.1 Subdivisions of a bin: cylinder (vertical section at top), hopper (converging section below).
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 16, 2008 7:51
Flowing material
Stagnant material
this definition, a bin that contains any stagnant material during discharge qualifies the flow
pattern as funnel flow.
Rotter (2005) further refined the definition of funnel flow into pipe flow and mixed flow.
The distinction between the two is whether or not the flow channel intersects any portion
of the walls of the bin (usually in the cylinder section). If there is no intersection (pipe
flow), the flow channel walls may be vertical (parallel pipe flow), converging from top to
bottom (taper pipe flow), vertical along the sidewall of the bin (eccentric parallel pipe flow)
or converging along the sidewalls of the bin (eccentric taper pipe flow) (see Figure 2.3).
If the flow channel intersects the cylinder wall (mixed flow), the converging flow channel
may be symmetric about the centreline of the bin (concentric mixed flow), fully eccentric if
the hopper opening is to one side of the vessel (fully eccentric mixed flow), or intersecting
the cylinder walls at varying elevations because of a partially eccentric outlet (partially
eccentric mixed flow) (see Figure 2.4).
In contrast to funnel flow, Jenike defined mass flow as a flow pattern in which all of
the material is in motion whenever anything is withdrawn (see Figure 2.5). Note that this
definition does not require that all material at a given evaluation across the cross section
be moving at the same velocity. Indeed this is nearly impossible elevation to achieve, since
particles near the centreline of a bin have virtually no shearing resistance, whereas particles
sliding along converging hopper walls flow move slowly. This velocity distribution can be
minimised by appropriate choice of hopper angle and hopper wall material of construction,
or through the use of an insert.
One should beware of vendors claiming they can supply ‘mass flow’ bins with no con-
sideration of the hopper wall material or stored bulk solid. The term ‘mass flow’ is often
misused.
A third flow pattern, expanded flow, is a combination of funnel flow and mass flow (see
Figure 2.6). Usually this is achieved by placing a small mass flow hopper below a funnel
flow hopper. The mass flow hopper section expands the flow channel from the outlet up
to the top cross section of the mass flow hopper. It is important to ensure that this cross-
sectional area is sufficiently large so as to avoid ratholing in the funnel flow hopper section.
Expanded flow designs are generally considered only when the cylinder diameter exceeds
6 m or so.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 16, 2008 7:51
HOPPER/BIN DESIGN 71
Stationary Flowing
pipe
Stationary
Flowing
Flowing Flowing pipe
pipe pipe
(a) Parallel pipe flow (b) Taper pipe flow (c) Eccentric parallel pipe (d) Eccentric taper pipe flow
flow
Effective transition
Flow channel
boundary
Flow channel
boundary
Flow channel
boundary
Flow
Flow
zone
zone
Effective Stationary Stationary
hopper zone zone
Stationary
(a) Concentric mixed flow (b) Fully eccentric mixed flow (c) Partially eccentric mixed flow
HOPPER/BIN DESIGN 73
θc
40° Funnel
20°
Mass Uncertain region
10° flow
0°
0° 10° 20° 30° 40° 50°
θc : Conical hopper angle, from vertical
Figure 2.7 Example of conical hopper design chart (based on data from Jenike 1964).
Jenike (1964) presented a series of graphs defining the limits of hopper angle within
which mass flow can develop. The major variables that determine these limits are:
r Wall friction angle, φw . This is the arc tangent of the coefficient of sliding friction
between the bulk solid and hopper wall material. This value often changes with
pressure, usually decreasing as pressure increases. In order to achieve mass flow
throughout a hopper, it is important (and often sufficient) to determine the wall friction
angle at the pressure level expected near the hopper outlet, since this is the region of
minimum pressure during flow.
r Effective angle of internal friction, δ.
r Hopper geometry, e.g. cone, wedge.
Jenike’s graphs were developed for axi-symmetric cones (hopper angle measured from
vertical denoted as θc ) and for infinitely long wedge-shaped hoppers (θp ). Examples of
design charts are shown in Figures 2.7 and 2.8. The two primary bulk solid parameters that
affect limiting hopper angles for mass flow φw and δ are in turn often affected by temperature
(of the bulk solid and the hopper wall material), moisture, content of the bulk solid, hopper
θp
40°
φw : Wall friction angle
30°
Funnel flow
20°
0°
0° 10° 20° 30° 40° 50° 60°
θp : Planar hopper angle, from vertical
Figure 2.8 Example of planar hopper design chart (based on data from Jenike 1964).
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 16, 2008 7:51
wall material including its surface finish, and time of storage at rest. A secondary effect is
the particle size distribution of the bulk solid.
It is important to emphasise that φw values can be determined only by shear testing (as
described in Chapter 1). No other so-called flow tests (e.g. angle of repose) can provide this
information.
2.3 Arching
Arching (sometimes called bridging or doming) can result from either mechanical interlock-
ing or cohesive strength (see Figure 2.9). Mechanical interlocking occurs when particles are
large relative to the outlet opening, whereas cohesive arching occurs because of bonding
between particles.
To avoid interlocking arching, the outlet dimension must exceed some critical multiple
of the characteristic particle dimension. While this characteristic dimension is not well
defined, a conservative approach is to take this as the maximum length of a chord that spans
the particle in any direction. The minimum values for outlet size are as follows:
r For a circular or square outlet, the outlet size should be at least 6–8 times the charac-
teristic particle dimension.
r For an elongated outlet, its width must be at least 3–4 times the characteristic particle
dimension and its length must be at least 3 times the width.
Mechanical interlocking usually governs minimum outlet dimensions only when the bulk
solid’s mean particle size is greater than about 6 mm, there are few ‘fines’, and the material
has little to no surface moisture or other condition that would cause particles to adhere to
each other.
Sizing an outlet to avoid cohesive arch formation is not as simple as considering only
particle size. Flow properties tests need to be run to determine the material’s flow function,
which is the relationship between cohesive strength and consolidating pressure. Once this
has been obtained, the hopper’s flow factor must be determined. The original source for
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 16, 2008 7:51
HOPPER/BIN DESIGN 75
flow factors, and still a convenient way of obtaining them, is through graphs presented by
Jenike (1964).
To avoid arching in a mass flow hopper, the outlet diameter BC (see Figure 2.10), or the
width of wedge-shaped outlet BP (see Figure 2.11), must be at least the following:
σ̄1 H (θ)
B= (2.1)
gρb
where B is BC or BP, m; σ̄1 is the critical stress required to cause arch to fail, N/m2 ; H (θ )
is the dimensionless function dependent on hopper angle (Jenike 1964). Value typically
ranges from 2.0 to 2.3 for conical mass flow hoppers, half this for wedge-shaped hoppers; g
is the acceleration due to gravity, 9.81 m/s2 ; ρb is the bulk density at consolidating pressure
calculated at hopper outlet, kg/m3 .
For a wedge-shaped hopper, the outlet length must be at least two times its width if the
end walls are vertical and at least three times its width if the end walls are converging.
To avoid arching in a wedge-shaped funnel flow hopper, the outlet width, BF, must be
at least that calculated using Equation (2.1) with the appropriate values of σ̄1 and ρb and
H (θ) = 1.
A material’s flow function, which can be determined only by shear tests, is often strongly
influenced by its temperature, time of storage at rest, moisture content and particle size
distribution. A hopper’s flow factor is a function of the effective angle of internal friction
(δ), wall friction angle (φw ) and hopper geometry.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 16, 2008 7:51
2.4 Ratholing
Also called piping, this is a phenomenon in which a more or less vertical flow channel
develops above the hopper opening and, once emptied, remains stable (see Figure 2.12).
In order to avoid the formation of a stable rathole, it is necessary that the size of the flow
channel exceed the critical rathole diameter, DF, which is calculated as follows:
σ̄1 G(φ)
DF = (2.2)
gρb
where σ̄1 is the cohesive strength of bulk solid at major consolidating pressure calculated
at bin outlet, N/m2 ; G(φ) is the dimensionless function dependent on bulk solid’s angle of
internal friction (Jenike 1964). Typical values range from 2.5 to over 7.
The two key parameters in this equation, flow function and angle of internal friction,
can be strongly affected by the bulk solid’s temperature, time of storage at rest, moisture
content and particle size distribution.
The maximum discharge rate of a coarse, freely flowing material through an orifice (i.e.
hopper outlet) can be calculated using the following equation:
1/2
Bg
Q = ρb A (2.3)
[2(1 + m) tan θ ]
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 16, 2008 7:51
HOPPER/BIN DESIGN 77
where Q is the maximum steady discharge rate, kg/s; ρb is the bulk density, kg/m3 ; A
is the cross-sectional area of outlet, m2 ; B is the outlet diameter or width, m; m = 1 for
conical hopper, 0 for wedge-shaped hopper; θ is the hopper angle (measured from vertical)
in degrees.
This equation can be modified to take particle size into account, but this alteration is
important only if the particle size is a significant fraction of the outlet size (Beverloo et al.
1961).
The limits of this equation are as follows:
r The bulk solid must be coarse. This is usually interpreted as a material having a mean
particle size of at least 6 mm with a minimal amount of fines.
r The bulk solid must be free-flowing. Essentially this means that there are no arching
or ratholing concerns.
Fine powders behave dramatically different than coarse, free-flowing bulk solids do. The
discharge rates of fine powders through a hopper opening may be excessively high (a phe-
nomenon called flooding) or excessively low. Which of these extremes occurs depends to a
large extent on the flow pattern in the bin. A funnel flow bin will often exhibit flooding as a
result of a stable rathole collapsing and the material becoming fluidised. Another way that
flooding can occur in a funnel flow bin is when fresh material added to the bin channels
through a stable rathole, resulting in a short residence time for the solid to deaerate.
Mass flow bins, on the other hand, often have a limited rate of discharge when handling
fine powders. This is due to interstitial gas flow through the voids as a result of (often small)
gas pressure gradients that develop naturally as material flows through a converging hopper.
Such gradients are not present with coarse, free-flowing materials because of their much
larger void space. Often the gas pressure gradient at the outlet of a mass flow hopper acts
upward, drawing in air through the outlet. Acting counter to gravity, this retards flow, and
the result can be limiting rates of discharge that are several orders of magnitude smaller
than a coarse, free-flowing material having the same bulk density.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 16, 2008 7:51
The discharge rate of fine powders from mass flow bins can be significantly increased by
using low levels of aeration. As discussed by Royal and Carson (1991), one technique is to
use an air permeation system, which consists of a sloping shelf or insert that allows a small
amount of air to be added to the bin. This air permeates into the bulk solid and lessens the
need for air to be drawn in through the outlet. One must be careful to distribute the air as
uniformly as possible to maximise its effectiveness, limit the air flow rate and pressure so
not to cause fluidisation, and avoid impediments to solids flow through proper design of the
sloping shelf or insert.
Another technique is to aerate the bulk solid as described below.
Two material parameters that affect flow rate and aeration characteristics are a pow-
der’s permeability and compressibility. Tests are available by which each can be measured.
Analysis of the results of these tests, including calculations of critical, steady state rates of
discharge, is quite complex.
2.6 Segregation
2.6.1 Sifting
This involves the movement of smaller particles through a matrix of larger ones (see
Figure 2.13). In order for sifting to occur, four conditions must exist:
r Range of particle sizes, typically a minimum ratio of 2:1 or more
r Mean particle size larger than about 500 μm
r Free-flowing material
r Interparticle motion
HOPPER/BIN DESIGN 79
If any one of these conditions does not exist, segregation by the sifting mechanism is
unlikely. Testers are available (ASTM 2003a) by which the sifting segregation tendency of
a material can be determined.
The outlet region of a hopper is more important than any other region of a bin in determining
both the flow pattern that develops as well as the type and extent of flow problems.
While it is obvious that, when gravity alone is acting, particles flow downward from the
top of a bin to the outlet, flow is actually initiated at the outlet when a gate is opened or a
feeder is started. Flow then propagates from the outlet upward, so what happens in the outlet
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 16, 2008 7:51
Plan view
Layer of fines
Elevation
region is extremely important. Furthermore, if a mass flow pattern develops in the hopper,
the solid’s pressure acting on the particles as well as between the particles and the hopper
wall is at its minimum value at the outlet. Since the wall friction angle φw is often not a
constant and usually varies such that its highest value occurs at the lowest pressure, this
results in the outlet region requiring the steepest hopper angle for mass flow to develop.
Arching or ratholing, when they occur, almost always do so at a hopper outlet. The reason
is obvious, since the outlet is (almost always) the smallest flow channel through which the
material must move.
Another reason why the outlet region is so important is that it directly affects the maximum
discharge rate achievable from the hopper. No matter whether critical discharge is calculated
using Equation (2.3) or is limited by fine powder flow, critical discharge rates vary more or
less linearly with outlet area.
Avoiding flow impediments throughout a bin is important if full mass flow is to be
achieved. Such impediments are particularly troublesome if they are present in the outlet
region and include mismatched bolted flange connections (see Figure 2.16), sight glasses,
poke holes and partially opened slide gates. The importance of good weld quality and
finishing in this region cannot be over-emphasised, even while recognising that polishing
near small openings is difficult.
When flow problems occur, many operators resort to a mallet to encourage flow, and
the blows are often directed to the outlet region since that is where most flow problems
originate. Unfortunately, mallet blows can distort a hopper, thereby creating even more of
an impediment to flow.
Two other causes of flow problems that can occur due to problems at a hopper outlet are
improper feeder design and upward gas pressure gradients. If a feeder is not designed to
fully activate the outlet area,1 this will prevent mass flow from developing in the vessel,
thereby potentially creating significant flow problems. Gas pressure gradients within a bin
1
See Figure 2.17, Chapter 5 and Carson (2000a).
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 16, 2008 7:51
81
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 16, 2008 7:51
are often concentrated and most detrimental when they occur at the hopper outlet. An upward
pressure gradient can significantly retard the bulk solid’s discharge rate, particularly if a
fine powder is being handled, and can also create arching problems with cohesive bulk
solids.
When handling a fine powder, a mass flow pattern to avoid ratholing and accompanying
flooding is usually advisable. However, as noted above, this often results in limited discharge
rates. If higher discharge rates are required and two common approaches (adding an air
permeation system or increasing the outlet size – and accompanying gate and feeder size)
cannot satisfy the demand or are impractical, there are two alternatives: fluidised discharge
and air-assisted discharge (Troxel et al. 2005).
These techniques are similar in that they involve use of a permeable membrane that covers
most or all of the hopper section. Air (or some other gas) is added into the bin through a
plenum located below the permeable membrane. These techniques differ in the quantity of
material fluidised and whether or not a feeder is used.
A fluidised discharger is used when the bin size is such that its entire contents can be
fluidised, the bin walls are capable of withstanding hydrostatic pressures, a low bulk density
as the solid exits the bin is acceptable, and gas collection and cleaning are not a concern.
Discharge is controlled through use of a feeder suitable for metering fluids, such as a tightly
sealing rotary valve.
An air-assisted discharger is designed to aerate only a thin layer of bulk solid above the
permeable membrane. For such a system to work properly the air must be able to easily
exit the bin through its outlet when solids are discharged. This usually means that discharge
cannot be restrained, such as is the case with a flood-loaded feeder. Instead, a full port ball
or dome valve is used to discharge slugs of bulk solid from the bin.
Examples of these two techniques are given in Figures 2.18–2.19.
HOPPER/BIN DESIGN 83
Primary step-down
regulator
Shop air
Gas flow
To data
acquisition
Flow transducer
Secondary
low-pressure 22" dia. cylinder
regulator
Pressure
transducer
Plenum
Primary supply
pressure 22" dia fluidiser, 25" from
valve
horizontal, 1 78 " i.d. outlet
Primary step-down
regulator
Shop air
Gas flow
To data
acquisition
Flow transducer
Secondary
low-pressure
τ
22" dia. cylinder
regulator
Pressure
transducer
Plenum
Primary supply
pressure 22" dia fluidiser, 25" from
valve
horizontal, 1 78 " i.d. outlet
where the bin is to be used. In many parts of the world this limit on cylinder diameter is
approximately 4.3 m.
Whether or not the bin is to be shop fabricated, plant space considerations usually need
to be taken into account. For example, plant layout may limit the maximum bin diameter.
Access within the plant may dictate the maximum size that can be transported to the location
where the bin is to be placed.
Another consideration regarding bin size involves obtaining a reasonable height-to-
diameter ratio, H/D. Usually bins are most economical when this ratio is between roughly
1.5 and 4.0. While these are not firm limits, they do provide a good guideline for economical
construction. Vessels with smaller H/D values have much of their volume in the hopper
section, which is more expensive to fabricate than a cylinder. At the other end of the spec-
trum, vessels with large H/D values may be taller than necessary or be more subject to
wind or seismic considerations than a shorter vessel.
Vessel height limits may need to be considered in sizing the vessel. If the bin is to be
located inside an existing building, ceiling height limits the bin height unless a portion of
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 16, 2008 7:51
HOPPER/BIN DESIGN 85
the cylinder can protrude through the roof. If the bin is to be located outside a building, the
height of surrounding structures or zoning requirements may limit the maximum height.
Beyond these considerations, it is generally wise to limit vessel height in order to minimise
the height to which material must be elevated in order to fill the vessel. In considering vessel
height, it is important to include the added height of other equipment that must go on the
roof, such as bin vents, dust collectors, etc.
Figure 2.20 Example of splitting single, centred outlet into multiple outlets at same radius.
2
Effective head is the height of a column of the bulk solid contained in a cylinder with frictionless walls. It can
be calculated by dividing the consolidating pressure by the solid’s bulk density.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 16, 2008 7:51
HOPPER/BIN DESIGN 87
d D
√12 √12
d D
2 2
Discharge Discharge
conveyor conveyor
D D
Avoid Recommended
Figure 2.22 Plan views showing poor (left) and good (right) placement of outlets to minimise effects of
segregation.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 16, 2008 7:51
to increase the outlet size to match the next larger feeder size above that required by other
considerations. If an elongated outlet is being used, the appropriate length of the feeder
may set minimum and maximum outlet lengths. Also, the speed of the feeder may set the
outlet size larger than required to overcome arching or ratholing or to accommodate the feed
rate. A small feeder operating at too high a speed may not be efficient or may be subject
to unacceptable abrasive wear or cause excessive particle attrition. Enlarging the feeder to
reduce its speed may correct these problems.
Sometimes with rate limiting powders an air permeation system or air-assisted dis-
charge can be used to increase flow rate and thereby limit the outlet size. Some powders
are also more suitable to being handled in a fluidised state, which also limits the outlet
size.
The shape of the outlet is the next consideration, in particular whether it should be cir-
cular, square or elongated. If there is a need to interface with downstream equipment such
as a standpipe, this often requires the outlet to be circular because most standpipes are
circular (to be able to effectively withstand explosion pressures). If the vessel is feeding
into a pressurised environment, either a standpipe or a special type of feeder may be re-
quired, either of which may limit the choice of outlet configuration. Another aspect is the
flexibility of location of the inlet point to downstream equipment, for example a conveyor
or process vessel. If this downstream inlet is offset from the vessel centreline, a circular
or square outlet will have to be followed by a conveyor or sloping chute, either of which
may be unacceptable. Using an elongated outlet with a screw or belt feeder may be a better
choice.
The type of feeder to be used also influences the shape of the outlet. If a rotary valve
is chosen because of process considerations, the hopper outlet must generally be either
circular or square. On the other hand, if a screw or belt feeder is to be used, the outlet
is often elongated. It must be noted that with such an outlet the interface details become
extremely important to ensure that the outlet area is fully active. There are several other
feeder types besides these three, but the general considerations are similar.
If a circular or square outlet is being used, the hopper configuration must generally be
either a cone or a pyramid, respectively. Associated with a pyramidal geometry are valley
angles and inflowing valleys, both of which must be considered. Generally, a pyramidal
geometry should be avoided if a mass flow pattern is required.
If the outlet is to be elongated, several hopper configurations are possible. Perhaps the
most common is a transition hopper as shown in Figure 2.23. If mass flow is required, the
end wall angle can be no less steep than the conical mass flow angle, σc , the sidewall angle
can be no less steep than the mass flow planar angle, σp , and the outlet length-to-width ratio
must be at least 3:1.
Another hopper configuration compatible with an elongated outlet is a chisel hopper as
shown in Figure 2.24. Here the end walls are vertical, so only the slope of the sidewalls
needs to be considered when designing for mass flow. The minimum length-to-width ratio
for this design to achieve mass flow is 2:1.
A wedge-shaped hopper can also be used with elongated outlets, although as with pyra-
midal hoppers there is concern with valley angles and inflowing valleys (see Figure 2.25).
One way around this is to use a series of alternating one-dimensional wedges as shown in
Figure 2.26. With this arrangement, the minimum length-to-width ratio of the outlet can be
as small as 2:1 since the end walls are vertical.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 16, 2008 7:51
HOPPER/BIN DESIGN 89
2.9.4 Inserts
Once the hopper geometry has been chosen, the next consideration is whether or not an
insert is required within the hopper. A common insert configuration is an inverted cone or
pyramid as shown in Figure 2.27. Unfortunately, studies have shown that such inserts have
a limited range of effectiveness and the loads acting on them are usually extremely high.
The supports required to resist these loads often provide impediment to flow greater than
the beneficial effect of the insert.
An alternative to this type of insert is a Binsert
R
(see Figure 2.28). This system was
developed for controlling and expanding flow patterns in bins by using a mass flow
θp
L W
L
>2
W -
HOPPER/BIN DESIGN 91
R r B
hopper-within-a-hopper. The inner hopper is designed to provide mass flow through the
central channel and also through the annular space between it and the outer hopper. This
concept is of considerable use in minimising particle segregation, saving headroom for mass
flow bin designs, eliminating ratholing problems in existing funnel flow bins by creating
mass flow and blending solids by either a single pass or recycling the solids through the
bin.
Uniform velocity
Vertical section
equal to the square cylinder’s width, so it requires less height to attain the same capacity.
Also, large rectangular bunkers with multiple hoppers are common in some industries, e.g.
coal-fired power plants.
Designers must be aware of structural issues as well as potential flow issues when de-
signing bins with flat walls. The structural issue is that of bending moments which must be
taken into consideration. The flow issue is that flat walls are usually connected to hoppers
that have inflowing valleys, which often results in a funnel flow pattern and can lead to flow
stoppages.
HOPPER/BIN DESIGN 93
The following is a brief discussion of typical problems that can occur with storage bins,
along with some common solutions.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 16, 2008 7:51
HOPPER/BIN DESIGN 95
tangential entry into the vessel. It will probably also be necessary to convert the vessel’s
flow pattern to mass flow.
(a)
(b)
(c)
HOPPER/BIN DESIGN 97
design errors, construction errors and operational issues (Carson 2000b). Within the category
of design errors, some of the problems that often occur are:
r Material properties and flow patterns not considered
r Out-of-round bending of a circular cylinder
r Large and/or non-symmetric loads caused by inserts
r Lack of proper consideration of specific requirements for structure type, such as bolted
metal or reinforced concrete
r Temperature or moisture effects resulting in thermal ratcheting or particle swelling
Construction errors include poor quality workmanship (incorrect bolts, incorrect placement
of reinforcing steel, incorrect material type or thickness) and unauthorised design changes
made during construction.
Operational practices that can cause structural problems include improper usage of the
vessel (e.g. a change in the stored material that results in higher loads being applied to the
vessel walls or adding additional outlets to the vessel wall, which changes the flow pattern).
Another operational issue is improper maintenance, such as allowing material to build up
on surfaces or ignoring the effects of corrosion.
Whatever the structural problem, it is essential that, at the first sign of trouble, there be an
appropriate response. Continuing to empty a vessel that is already starting to fail may well
result in complete collapse of the structure. Engineers trained in structural issues as well as
solids flow should be consulted to ensure that property damage is kept to a minimum and
personnel are kept out of harm’s way.
Silos and bins should be inspected on a routine basis to anticipate potential flow and
structural problems before these become major.
If the wear problem is due to abrasion, the first step should be to test the abrasive wear
characteristics of alternate liners (Johanson & Royal 1982) and then consider changing the
wall material or liner.
Another operational problem is unacceptable attrition. If this is occurring, consideration
should be given to using a letdown chute, reducing the size of the bin or changing the type
of feeder to one that provides fewer pinch points.
References
ASTM D6940-03 (2003a) Standard practice for measuring sifting segregation tendencies of bulk solids. In:
Annual Book of ASTM Standards, Vol. 04.08. American Society for Testing and Materials International, West
Conshohocken, PA.
ASTM D6941-03 (2003b) Standard practice for measuring fluidization segregation tendencies of powders. In:
Annual Book of ASTM Standards, Vol. 4.08. American Society for Testing and Materials International, West
Conshohocken, PA.
Bates, L. (1997) User Guide to Segregation. British Materials Handling Board, Elsinore House, Marlow, England.
Beverloo, W.A., Leniger, H.A. & Van de Velde, J. (1961) The flow of granular solids through orifices. Chem.
Eng. Sci., 15, 260–269.
Carson, J.W. (2000a) Step-by-step process in selecting a feeder. Chem. Process., Powder Solids Annu., 38–41.
Carson, J.W. (2000b) Silo failures: case histories and lessons learned. Proceedings of the 3rd Israeli Conference
for Conveying and Handling of Particulate Solids, Vol. 1, pp. 4.1–4.11, Dead Sea, Israel.
Carson, J.W., Purutyan, H. & Rotter, J.M. (2003) The dangers of relying on wall friction values in codes. 4th
International Conference for Conveying and Handling of Particle Solids, Budapest, Hungary.
Carson, J.W., Royal, T.A. & Goodwill, D.J. (1986) Understanding and eliminating particle segregation problems.
Bulk Solids Handling, 6, 139–144.
Carson, J.W., Royal, T.A. & Pittenger, B.H. (1995) Mass flow purge and conditioning vessels. Chem. Process.,
58(8), 77–80.
Jenike, A.W. (1964) Storage and Flow of Solids. University of Utah Engineering Experiment Station, Bulletin
No. 123.
Johanson, J.R. & Royal, T.A. (1982) Measuring and use of wear properties for predicting life of bulk materials
handling equipment. Bulk Solids Handling, 2, 517–523.
Pittenger, B.H., Carson, J.W., Prescott, J.K. & Purutyan, H. (1999) Uniform purging of resins in contact bed
purge vessels. Polym. Eng. Sci., 39, 1802–1811.
Rotter, M.J. (2005) Silo design loads from stored bulk solids: the provisions of the new Eurocode EN 1991-4
(2005). Proceedings of the IMechE Seminar on Specifying and Designing Safe Storage Silos, IMechE.
Royal, T.A. & Carson, J.W. (1991) Fine powder flow phenomena in bins, hoppers, and processing vessels.
Presented at Bulk 2000, London.
Troxel, T.G., Carson, J.W. & Bengston, K.E. (2005) Proven techniques for air-assisted handling of powders in
bins and hoppers. 7th World Congress of Chemical Engineering (C13-008).
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:17
3.1 Introduction
Silos and hoppers are widely used in a great many different industries for storing a huge
range of different solids. The sizes of these silos may vary from capacities less that 1 tonne
to the largest containing as much as 100 000 tonnes. The size of the silo has a strong bearing
on the number of different considerations required: small silos generally do not produce
structural problems, but in large silos many different aspects need careful attention.
The designs used for silos also vary very much (Figure 3.1). In some industries (e.g. grain
storage), there is a competitive industry producing standard silo products which function
extremely well and cost-effectively provided the conditions remain those anticipated. In
other industries (e.g. cement and mineral ore storage) very large silos are used and every
silo must be individually designed for the special conditions. It should be noted that each
silo is normally designed to contain a very limited range of solids, and that the use of a silo
designed for one kind of solid to store different solids can easily cause damage. Bulk solids
vary very much in their properties, and a silo that is perfectly adequate to store one material
may be very dangerous for another.
The terms silo, bunker, bin and hopper are often used to refer to similar containers in
different industries. Here, the word ‘hopper’ is exclusively used with a special meaning for
the converging part leading to a gravity discharge outlet. All complete storage containers
are referred to as silos, irrespective of the stored solid, geometry and industrial sector. A
characteristic form to describe the parts of the silo is shown in Figure 3.2. The transition,
which lies at the junction between the vertical wall and the hopper, should be noted.
This chapter provides a brief outline of the development of understanding of pressures
that develop in silos and their consequences for the safety of the silo structure. More
structural failures occur in silos than in any other engineered structural form, considering
the numbers of each, and these failures occur in all countries and all industries. Structural
design considerations for silos are therefore a key aspect of bulk solids handling systems.
The chapter refers extensively to the provisions of the recently developed European stan-
dards for silo pressures (EN 1991-4 2007) and for metal silo structural design (EN 1993-4-1
2007), for which the author was the chief contributor and editor. Further useful information
relating to the structural design of all silos may be found in Rotter (2001a).
3.2.1 General
The pressures that develop in a silo are very different from those developing in a tank that
contains fluid. Fluid pressures depend uniquely on the head, and in most fluid storages
flow velocities are so low that dynamic effects are small. By contrast, pressures in silos
Bulk Solids Handling: Equipment Selection and Operation Edited by Don McGlinchey 99
© 2008 Blackwell Publishing Ltd. ISBN: 978-1-405-15825-1
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:17
(a) 10 000 tonne steel grain storages, (b) Corrugated steel (c) Rectangular concrete silo
Australia storage, Germany battery, Austria
(d) Older concrete and newer steel (e) Salt storage with (f) FRP farm silo, France
silos, France control room, Italy
are dominated by frictional phenomena, the flow of bulk solids is controlled by frictional
considerations and is largely independent of head, and there are few analogies between fluid
and solid storage that are either valid or practically useful. In this context, it is worth noting
that sound mechanics equations to describe fluid flow have existed for over a hundred years,
but no comparable agreed set of equations yet exists to deal with bulk solids flow.
Pressures that develop in stored solids can have an important impact on their free flow
from a silo if the bulk solid is prone to developing a small cohesive strength under stress
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:17
Roof
Vertical wall:
– cylindrical if circular
– flat plates if rectangular
Transition
Ring:
used if silo is circular
Skirt
Hopper:
– conical if silo is circular
– trapezoidal if silo is rectangular
(e.g. flour). These aspects are dealt with in the accompanying chapter by Dr John Carson
and are not commented on further here.
The most critical aspect of pressures in silos is their effect on the structure designed
to contain the solid. Because the properties of solids vary widely, the pressures can also
vary very much both in magnitude, distribution and stability. Some conditions lead to very
unpredictable pressure peaks that can cause serious damage, whilst other arrangements are
very benign and do not cause any concern even to the unwary. This chapter tries to make
some clear distinctions between these different situations.
In particular, where pressures in silos are being defined for the purposes of structural
design, an understanding of the consequences for the structure is absolutely vital. Thus,
it is often imagined that high pressures, wherever and whenever occurring, are the most
damaging event. This is very far from the truth, and many theories of silo pressure and
scientific articles on pressures are very misleading because their authors did not understand
what stress conditions would be induced in the structure by the pressures, nor the conditions
that lead to structural failure. This chapter sets out some pointers to that information and
it is hoped that the reader will appreciate that this subject is not straightforward, but a full
explanation is beyond the scope of this chapter.
Flowing
Flowing
Effective transition
Effective
transition
Flow channel
boundary Flow channel
Flow channel
boundary boundary
Stationary Stationary
Stationary
(a) Retaining silo (b) Squat silo (c) Slender silo (d) Very slender silo
A second key distinction is the overall size of the silo. Small silos do not present structural
challenges and can be designed using fairly simple calculations. Very large silos need great
attention to many details. For this reason, EN 1991-4 divides silos into three categories
according to the mass of solid stored, and has different design requirements for each. The
break points occur at 100 tonnes, 1000 tonnes (for special cases) and 10 000 tonnes. The
standard on structural design of steel silos makes similar divisions, though at different values
because it is concerned with aspects of the structure, not the loading. The break points occur
at 100, 200 (with eccentric discharge), 1000 (elevated) and 5000 (ground supported) tonnes,
with considerable design calculation effort being demanded where the largest sizes are used.
A third key classification is necessary to define the pressure regime. This is the aspect
ratio (height H divided by horizontal dimension D). Most silos research has studied slender
silos (H/D > 2) and most of this chapter is concerned with this geometry. In squat silos
(H/D < 1), the top surface profile plays an important role and issues of the difference
between filling and discharge pressures are much reduced (Pieper & Stamou 1981). EN
1991-4 gives different rules for each aspect ratio, classing them as slender, intermediate,
squat and retaining (Figure 3.3).
Equivalent
surface
q
z
τ
dz Solid, ρb
p
dz
q + dq
p
k= q μ = τp
D
or
dq
A + U τ = ρb A (3.1)
dz
The vertical stress q on the slice need not be uniform: the analysis considers only the
mean value. Horizontal equilibrium of the slice requires some symmetry to exist in the wall
pressures p, but they need not be constant around the perimeter (this becomes a serious
issue later). Shear stresses on the top and bottom of the slice are assumed to integrate to a
zero resultant on each face.
Two assumptions are next made (as used by Janssen):
a The full wall friction is assumed to be developed against the wall at every point, so
that the mean frictional shear τ is related to the mean normal pressure p on the wall
through the wall friction coefficient μ (Figure 3.4) as
τ = μp (3.2)
b The normal pressure p (mean value around the perimeter) is deemed to be related to
the mean vertical stress q through a lateral pressure ratio K (Figure 3.4) as
p = Kq (3.3)
Inserting these into Equation (3.1) leads to
dq U
+ μK q = ρb (3.4)
dz A
which may be solved to yield
ρb A
q = q|z=0 = 0 + 1 − e−zU/(AK μ) (3.5)
μU
If the mean vertical stress in the solid q is taken as zero at some reference height z = 0
(Figure 3.4) (this condition is met at the centroid of the top pile of solids), then
q|z=0 = 0 (3.6)
and Equation (3.5) can be more neatly written as
q = q0 (1 − e−z/z0 ) (3.7)
in which
q 0 = ρb z 0 (3.8)
and
1 A
z0 = (3.9)
μK U
Here, q0 represents the mean vertical stress in the solid that is reached asymptotically at
great depth. The length measure z 0 defines the rate at which the asymptote is approached
and is commonly termed the Janssen reference depth.
The origin of the vertical coordinate z (at the centroid of the top pile of solids) is called
the equivalent surface.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:17
Normal
pressure p
Linear pressure at
zo
shallow depth
p = K ρb z
p
0.63 po
zo Janssen
normal pressure
0.86 po
zo Asymptotic value
at great depth, po
0.95 po
It is natural to transform Equation (3.7) into pressures normal to the wall p (Figure 3.4)
p = p0 (1 − e−z/z0 ) (3.10)
μp0 U = ρb A (3.13)
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:17
or
ρb A ρb R
p0 = = (3.14)
μU 2μ
Thus, every theory that assumes that the wall friction is fully developed must reach the same
asymptotic value of lateral pressure p0 at great depth. This applies whether the silo is just
filled or is being emptied.
At shallow depths, the pressures vary linearly with depth and are approximated by
p = Kρb z (3.15)
which is the ‘earth pressure’ against a retaining wall. However, this theory does not take
proper account of the surface profile in defining wall pressures near the surface, and this
matters in squat silo geometries (see EN 1991-4 2007).
The Janssen theory is the main descriptor of filling pressures in all standards.
v
Lateral
pressure ratio K v
Rankine passive limit Kp K
Plastic deformations
of the solid
The value for K 0 has long been approximately related to the angle of internal friction φi
of the solid (Jaky 1948) as
K 0 = 1 − sin φi (3.18)
The background to this equation may be read in Muir Wood (1990).
The ideal K 0 relates to conditions in which the vertical and horizontal stresses are principal
stresses and both uniform. Since the state of the silo after filling has both a non-uniform
vertical stress pattern and shear stresses against the wall, it is best here to assign the value
K f for the filling state, noting that K f > K a , but K f ≈ > K 0 .
It is best to measure the lateral pressure ratio K directly (see Chapter 1), but it has long
been common to estimate it from the measured angle of internal friction φi . Accounting for
the above effects, the European standard EN 1991-4 (2007) defines the filling value of K f
for design purposes as
K f = 1.1(1 − sin φi ) (3.19)
Equivalent
surface
q + dq
z
2r qlocal
dx Solid, ρb p
τ
dx
p
q H
x
p is normal
p
F=q μh = τ to the wall τ
p
p = Fq
Figure 3.7 Hopper slice analysis, coordinate system and local equilibrium.
where k1 = π for a conical hopper and k1 = 4 for a square hopper of half side r . The
perimeter of the slice is given by
where k2 = 2π for a conical hopper and k2 = 8 for a square hopper of half side r . Vertical
equilibrium of the slice of solid (Figure 3.7) leads to
Stored
solids
γ
β
Transition
Figure 3.8 Mean vertical stress at the transition and overall hopper equilibrium.
or
dq
x − n q = −ρb x (3.27)
dx
in which
n = 2[F + Fμh cot β − 1] (3.28)
which may be solved, considering the top boundary condition q = qt at x = H , to yield
x n ρb H x x n
q = qt + − (3.29)
H (n − 1) H H
where qt is the mean vertical stress in the solid at the transition (Figure 3.8).
It is evident that the value of F must depend on geometry and solids properties, just as
K was dependent on solids properties in the analysis of the pressures on vertical walls.
The normal pressures may be deduced from Equation (3.29) as
x n ρb H x x n
p = F qt + − (3.30)
H (n − 1) H H
Equation (3.30) gives a variety of different forms for the hopper pressure distribution,
depending on the value of F. The two components of loading are clearly separated: the
weight of solids in the hopper (term involving ρb H ) and the pressure derived from the
cylinder (transition surcharge qt ). Equation (3.30) indicates that high local pressures can
occur at the transition if the barrel has a moderate height and F is high. The distribution
becomes very peaked at the transition for high n which arises if F is high and the hopper
is steep and rough. This theory is used in EN 1991-4 (2007), but older standards (e.g. DIN
1055-6 1987) often gave empirical approximations to the pressure pattern which could not
be guaranteed to be safe in all conditions.
These pressure patterns are illustrated in Figure 3.9, where the changing shape of the
hopper wall pressures caused by transition vertical pressures qt is illustrated for different
values of F.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:17
0.9
beta = 30
Vertical coordinate in hopper x/H
0.8
F = 0.659 mu = 0.3
0.7
F = 0.7
0.6 F = 0.8
F=1
0.5
F = 1.3
0.4 F = 1.7
F = 2.2
0.3
F = 2.8
0.2 F = 3.5
0.1
0
0 0.5 1 1.5 2 2.5 3 3.5 4
Dimensionless normal pressure p/qt
The question of whether the friction is fully mobilised in a hopper depends on its slope
and the smoothness of the wall. The hopper is classed as steep if the solids slide on it, and
this is met by the following test. The hopper is steep if
1−K
tan β < (3.31)
2μh
where μh is the full wall friction coefficient on the hopper, which may have a lining. This
relationship is plotted in Figure 3.10a for clarity. The effect of steepness on the pattern of
pressures in hoppers during emptying of the silo is illustrated in Figure 3.10b.
However, the most critical feature of a hopper is not the wall pressure distribution but
the overall equilibrium shown in Figure 3.8. Most structural failures of hoppers occur by
rupture at the transition under the stress resultant n φ . High values of n φ are chiefly caused
by an excessive vertical pressure qt from the cylinder, probably when this is underestimated
through inadequate attention to material variability (Section 3.3.6).
1.0
0.9
h
Hopper wall friction coefficient
0.8 Shallow K = 0.3
K = 0.4
0.7
K = 0.5
0.6 K = 0.6
0.5 K = 0.7
0.4
0.3
0.2 Steep
0.1
0.0
0 10 20 30 40 50 60
Half angle of hopper (degrees)
pe
z pe
qvt pn pf
zt
H
x
pne pne
Steep Shallow
tension in the wall (Figure 3.11) was all that needed to be considered, leading to
where n θ is the circumferential force per unit height in the wall. This equation is valid if
the pressures are constant around the perimeter at any level in the silo. It indicates that
higher pressures will lead to higher tensions and so presumably will be more damaging
to the silo wall. This over-simplified concept has underlain much of the pressure values
reported from silo research in the last century, and is certainly responsible for some failures
which occurred when pressures dropped locally (see Section 3.4.5). The maximum pressure,
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:17
symmetrical effects of
p Janssen pressure
distribution
Stored p
p
R bulk solid
nθ = K zR
nθ nz = ∫ p dz
nθ = poR
(a) Horizontal tension (b) Silo with stored solid (c) Typical pattern of wall membrane
in silo walls and wall pressures forces from symmetrical pressures
especially if local and of short duration, is not usually a prime cause of structural damage to
silos.
Accompanying the pressure p against the wall is the frictional traction τ (Figure 3.4),
which accumulates to produce vertical (axial) forces in the silo wall. Since the vertical
pressure in the solid reaches an asymptotic limit (Equation (3.8)), the weight of all the
additional solids must be borne instead by vertical forces in the wall (Figure 3.11c).
Adopting Janssen’s theory for the pressure pattern, the resulting axial force per unit
circumference n z developing in the silo wall under symmetrical conditions is then
z z z
z
nz = τ dz = μpdz = μp0 (1 − e−z/z0 ) dz = μp0 z 0 − 1 + e−z/z0 (3.33)
0 0 0 z0
This compressive force rapidly approaches a linear increase with depth (term z/z 0 )
(Figure 3.11c). Thus very high forces develop in the wall towards the bottom of the silo.
This force is important in thin metal silos, as it becomes the critical effect because the
controlling design consideration is buckling under axial compression (see Section 3.5.2).
This is the reason why metal silos must have a much greater wall thickness towards the
bottom than near the top.
The above theory for cylinders is not valid for conical hoppers. For them, even the simplest
stress analysis is much more complicated and is beyond the scope of this chapter. More
information may be found in Rotter (2001a).
In reading what follows it should be noted that metal silos are most sensitive to vertical
compression in the vertical walls, that concrete silos are most sensitive to normal pressures
against the walls, and that both of these structural materials are easily damaged by unsym-
metrical pressures, as noted in Sections 3.4.5 and 3.5. Finally, the hopper, which has not
been discussed yet, is usually chiefly loaded by the vertical stress in the solid at the transi-
tion. These different sensitivities demand that careful attention is paid to different parts of
the pressure theory, since it is not normal wall pressures alone that cause structural failures.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:17
Note 1: It should be noted that φ wh ≤ φ i always, since the material will rupture internally if slip at the
wall contact demands a greater shear stress than the internal friction can sustain. This means that, in all
evaluations, the wall friction coefficient should not be taken as greater than tanφ i (i.e. μ = tanφ w ≤ tanφ i
always).
Note 2: Hopper normal pressure pn is usually maximised if the hopper wall friction is low because less of
the total hopper load is then carried by wall friction. Care should be taken when choosing which property
extreme to use for the hopper wall friction to ensure that the structural consequences are fully explored (i.e.
whether friction or normal pressures should be maximised depends on the kind of structural failure mode
that is being considered).
Active or peaked
principal stress
field
Switch
Passive or arched
principal stress
field
ph
Stress field in solid Wall pressures
Figure 3.12 Original concept of the ‘switch’ during emptying. (After Gaylord & Gaylord 1984.)
Nanninga (1956) suggested that the changeover might occur over a finite depth (Figure
3.12), but later theorists who took up the idea (Arnold & McLean 1976; Jenike et al. 1973;
Walker 1966; Walters 1973) made the change into an abrupt step. This step was termed the
‘switch’.
Since the state was to pass from filling (close to an active stress state) to passive, the
pressure just below an abrupt step is easily determined as the Janssen value multiplied
by the ratio of passive to filling values of lateral pressure ratio (K p /K f ). The ratio of
peak symmetrical discharge pressure to symmetrical filling pressure is a very widely used
variable, and its origins can be seen here to have some foundation in mechanics. This ratio
is so important in silo design that it is given a symbol and defined as
pe
Ce = (3.34)
pf
in which pf is the normal wall pressure after filling and during storage (taken as the Janssen
pressure) and pe is the design value of the symmetrical pressure (uniform at a given height
in the silo) occurring during emptying (discharge). The above description leads to Ce =
K p /K f .
It was noted above that the ratio K p /K a for a typical bulk solid is of the order of 9,
making K p /K f of the order of 6. No observations of such huge increases in pressure were
ever reported, so several theories were advanced which tried to explain why the switch from
active to passive could produce lesser increases in pressure. The revised theories (Arnold
et al. 1980; Jenike et al. 1973; Walker 1966; Walters 1973) showed that the stress pattern in
the solid, involving non-uniform vertical stresses and shear stresses against the wall, could
lead to rather smaller wall pressure increases. The Walker and Walters treatments relied
on the solid being in a fully plastic (yielding in shear) state at all times, whilst the Jenike
treatment assumed that it was elastic. Typical examples of the resulting pattern of wall
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:17
zs/zo = 0.4
zs/zo = 0.8
1.5 zs/zo = 1.2
zs/zo = 2
2 Janssen
envelope
2.5
3
Kp/Kf = 2.5
3.5
4
0 0.5 1 1.5 2 2.5 3
Dimensionless pressure p/po
Figure 3.13 Consequences of a ‘switch’ in lateral pressure ratio at different levels (the switch is taken to
occur at depth z s ).
pressures are shown in Figure 3.13, where it is supposed that the ratio K p /K f is only 2.5.
Conventional wisdom, following the simple structural theory set out in Section 3.3.5, said
that the design must accommodate the envelope of pressures corresponding to the maximum
pressure applied at every level.
All these attempts still led to large predicted pressure increases during emptying, and
for a while it was accepted that very large increases in symmetrical wall pressures must
occur and should be designed for. A strange aspect of this idea was that, although many silo
failures did occur, few silos failed by bursting, which is what would have been expected if
the theories were accurate.
It may be noted that the pressure always returns to the Janssen asymptotic value p0
below the ‘switch’. The increase in the axial force developing in the wall is much smaller
(Figure 3.14) because the switch only affects the frictional shear transfer locally.
The most widely used switch theory for vertical walls was that of Jenike et al. (1973),
which still underlies the flow pressure rules in the Australian Standard AS 3774 (1996),
leading to a high ratio of design pressures for discharge to those after filling. This type
of theory is still commonly expounded (Drescher 1991) as a formal part of silo pressure
behaviour.
0.5 filling
Envelope
zs/zo = 0
of peak
1 zs/zo = 0.4
forces
Dimensionless depth z/zof
zs/zo = 0.8
1.5 zs/zo = 1.2
zs/zo = 2
2
2.5
3 Janssen
Kp/Kf = 2.5
3.5
4
0 1 2 3 4 5
Dimensionless membrane force nz/nzfo
Figure 3.14 Smaller rises in the vertical force in the wall beneath a ‘switch’.
rounded by the slow change (Figure 3.15). Here a progressive change in K from K f = 0.5
to K e = 1.4 (a ratio of K e /K f = 2.8) is assumed to occur between the heights z/z 0 = 0.6
and 0.75. The resulting changes in the mean vertical stress q/q0 , the mean wall pressure
p/ p0 and the emptying factor Ce are shown in Figure 3.15 with the assumed ratio K /K f
at each level. Because the change is progressive (as originally suggested by Nanninga), the
rise in pressure from filling to emptying is only a factor of 1.5 instead of 2.8 (i.e. the step
change greatly exaggerated this phenomenon). The same analysis yields similar results for
different locations of this change and thus leads to the conclusion that, although the stress
field must undoubtedly change from the filling to emptying states, the magnitude of the
symmetrical rise in pressure is greatly overpredicted by these simple switch theories. The
European Standard (EN 1991-4 2007) consequently prescribes much smaller increases in
symmetrical pressure during emptying (Ce values) than these older theories propose.
0.2
Janssen
Dimensionless height z/zo
0.3
0.4
0.5 Wall Lateral pressure
pressure
0.6 ratio
0.7
0.8
0.9
Vertical Discharge/filling
1 stress
pressure ratio
1.1
A typical set of observations from pressure cells on the side of a tall silo subject to
concentric filling and discharge and containing sand is shown in Figure 3.16, where the
pressure reading is plotted against time during the test.
The lowest pressure cell, A, is the first to register pressure (at 2 min), and the pressure
rises rapidly towards the Janssen asymptote. The other cells progressively start to register
H
6
Filling end:
Wall pressure (kPa)
G 5 31 min
p
F
E 4
pressure
cells D
3
C
B 2
A
1 Discharge start:
57 min
0
0 10 20 30 40 50 60 70 80 90 100
Time (mins)
Figure 3.16 Typical pressure cell record on a vertical line of cells in a test silo.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:17
as the silo is filled past the level they are at. It is interesting to note that at the end of filling
(31 min) the pressures are not in a neat order with the lowest cell registering the highest
pressure, but a little jumbled, indicating that the Janssen theory is not a precise tool like
pressures in a fluid vessel, but an approximate description. After the filling process ends,
the pressures are relatively stable, but not completely constant because small settlements
and minor disturbances cause small increases and decreases in different places at different
times.
At the instant that the discharge gate is opened (57 min) all the pressure cells begin to
fluctuate quite wildly, with pressures rising for short moments to as much as twice the filling
value but also falling to very low values. The largest departures from the filling state occur
relatively high up the silo wall at levels D and F with the cell at F once touching 6.2 kPa
from a Janssen reference value of 3.6 kPa (ratio of 1.7). But there is no evidence of a wave
of high pressure passing up the silo as the stress field passes from filling to passive, and the
switch theory of silo pressures on vertical walls, at least in its original form, is probably not
widely believed any more.
Many silo pressure researchers, when faced with such voluminous data as this which is
clearly not easily assimilated, have tried to find values that can be reported as relevant to the
discharge condition, and it is quite natural that the highest pressure occurring on each pres-
sure cell should be reported, irrespective of whether these values occurred simultaneously
and whether they endured very long. Thus, the literature has many reports of major depar-
tures from the filling state, but the significance of these departures is highly questionable.
The classic interpretation process is illustrated in Figure 3.17, where different cells reach
peak pressures at different instants, the envelope of these peak pressures is represented as
the outcome of the test, and a Janssen envelope is fitted to cover the outcome so that the
result can be reduced to a single overpressure factor Ce . Alternatively, revised values of K
and μ could be given to represent the emptying process (e.g. DIN 1055-6 1964). Many of
the difficulties with such simplified interpretations were discussed by Rotter et al. (1986):
in particular, the most damaging instant for the silo structure is not detected or encompassed
by this process.
One must not be too unkind to the researchers who reported these experiments. The
instrumentation is very expensive, so most tests were conducted with relatively few pressure
cells. Faced with the challenge of where to place their few cells, most experimentalists were
persuaded by the above theories that placement down a vertical line on the side of the silo
would deliver the pattern of pressure to be expected, naturally a constant value at each level.
Consequently, the information concerning variation of pressure at a particular level is rather
sparse.
A further reason for using only one pressure cell at each level was that the simple theory
used to translate pressures into forces in the structure (Equations (3.9) and (3.10)) implied
that only the largest pressure needed to be found, and presumably that large pressure might
well pass by every point at a particular level, even if not quite simultaneously.
The pressures recorded at different points around the circumference in the same test as in
Figure 3.16 are shown for one level in Figure 3.18. First, it is clear that the pressures after
filling are not at quite the same value at one level. Second, the rises and falls in pressure
at different points around the circumference are not coincident, but lead to significantly
unsymmetrical patterns at different instants. A detail taken from Figure 3.18 is shown in
Figure 3.19.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:17
pA (t) Cell A
t
pB (t) Cell B
pC (t) Cell C
D
t
Cell D
pD (t)
7 Storing: pressures
stable but different Discharge: erratic
6 at different places pressure changes,
some very large,
Wall pressure (kPa)
5 some small
4
Filling:
3 pressures
rising
2
Filling Discharge
1 end: start:
31 min 57 min
0
0 10 20 30 40 50 60 70 80 90 100
Time from start of test (min)
Figure 3.18 Typical pressure cell record at a single level in a test silo.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:17
8
Discharge:
Maximum 7.5 kPa
7 erratic pressure changes,
some high values, some low
6
5
Wall pressure (kPa)
2
Discharge
start: Minimum 2.0 kPa
1 57 min
0
57 58 59 60 61 62 63
Time from start of test (min)
Figure 3.19 Detail of Figure 3.18 showing local rises and falls in pressure.
The key factor here is that unsymmetrical pressures are often damaging to cylindrical
silo structures, whether constructed in metal or concrete, and this effect is more important
than the possible peak pressure occurring at one point. In particular, if the peak pressure
only occurs at one point around the circumference, then the pressures are necessarily un-
symmetrical and the worst aspect of this load case is not the simple relationship between
normal pressure and circumferential (hoop) tension of Figure 3.11.
In the context of the above, a key set of experiments on full-scale silos was conducted in
Sweden over many years (1970–1980) by Nielsen and his co-workers (Nielsen 1998). This
project arose because of the extensive cracking which had been observed in many Swedish
grain silos. The experiments involved a 47 m high concrete silo of internal diameter 7 m,
filled with different grains in different experiments with both concentric and eccentric filling
and discharge. This huge set of experiments demonstrated many effects that are not included
in any silo design, notably the progressive changes in the properties of the stored solid as it
was handled, the sensitivity of pressures to anisotropic packing of the particles, the effects of
imperfections in the silo walls, the difficulty of making reliable observations with pressure
cells, and the fact that two pressure cells close to each other might, for limited periods,
record quite different values, indicating that there can be sharp jumps in pressure on the
wall.
The most critical finding for silo design was the systematic pattern of unsymmetrical
pressures, both after filling and during discharge (Ooi et al. 1990). The ratio of the largest
sustained pressure to the smallest at a single level could be as high as 2.8 under static
conditions after filling and 5.6 during discharge. This kind of discovery was also made by
Schmidt and Stiglat (1987) and led to the introduction of a required unsymmetrical design
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:17
pressure, called a ‘patch load’ in the German standard (DIN 1055-6 1987). The latest version
of this patch load treatment is given in EN 1991-4 (2007) where the patch load depends on
the filling or discharge state, the silo aspect ratio, the eccentricities of filling and discharge
and the construction medium.
The consequences of unsymmetrical pressure patterns are noted further in Section 3.5.
Flowing
Flowing
All solids
in motion Flow channel
boundary Effective transition
Flow channel
boundary
Stationary
Effective
hopper
Stationary Stationary
1.0
0.9 CONICAL HOPPERS
Hopper wall friction coefficient μh
0.8
0.7
0.6 Funnel flow
0.5 certain
0.4
0.3
Risk of mass
0.2 flow pressures in
0.1 this zone
0.0
0 20 40 60
Hopper apex half angle β (degrees)
Figure 3.21 Boundary between mass flow and funnel flow in silos with conical hoppers. (After EN 1991-4
2007.)
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:17
Filling Filling
Filling and
emptying
Emptying Emptying
(a) Mass flow (b) Mixed flow with (c) Pipe flow with
effective transition almost no changes
Figure 3.22 Typical patterns of average symmetric wall pressure after filling and during emptying, for
different flow channel geometries.
Under pipe flow (Figure 3.22c), the pressures against the wall are largely unaffected
by flow, so if the designer can be sure that no flow of solids against the wall will occur
(except at the surface), lower design pressures are possible. However, under mixed flow
(Figure 3.22b), the boundary of the flow channel strikes the wall and a local high pressure,
comparable to that in a mass flow hopper, often develops against the wall. This pressure is
somewhat unpredictable. It can vary in magnitude as the slope of the contact point changes,
it can be unsymmetrical from one side to the other, it is slightly cushioned by the stored
solid between the flowing solid and the wall, and in silo experiments, this is commonly the
point of greatest scatter and oscillation in pressure values. Despite all of this, very few silos
have ever failed by bursting at an effective transition, so this rather alarming knowledge
should not be a major cause for concern.
Finally, it must be clearly repeated that it is not yet possible to predict the geometries
of pipe flow and mixed flow solids flow patterns, so this rather critical distinction is not
yet quantifiable. The distinction is therefore not used in the design rules of EN 1991-4
(2007).
This is a substantial subject and beyond the scope of this chapter, but EN 1991-4 now
includes a simple definition of a design eccentric flow channel geometry and pressure regime
which may be used to achieve a satisfactory design. The equations used adopt the theory of
Rotter (1986b, 2001b). A circular silo with a part-circular flow channel in contact with the
wall (Chen et al. 2005) is shown in Figure 3.23, together with the characteristic pressure
distribution that is found in experiments. The vertical stresses induced in the wall by this
unsymmetrical pattern are also shown to indicate the dramatically large effect on this silo.
In particular, note that the highest compression stress occurs around the mid-height of the
silo in the middle of the flowing channel.
Eccentric discharge pressures of the pattern shown in Figure 3.23 also have a very dam-
aging effect on concrete silos, where severe bending of the wall induces substantial vertical
cracks and sometimes leads to spalling.
3.5.1 Introduction
The simplest stress analysis of a cylindrical silo structure under symmetrical loads was
presented above in Section 3.3.5. Unfortunately, this is often the only analysis that is applied,
sometimes with unfortunate consequences for the structure. Metal and concrete silos carry
their loads differently because metals are strong in tension but thin metal sections tend to
buckle under compression. By contrast, concrete is very weak in tension, but can resist
compression well. These aspects lead to different key design considerations.
Both metal and concrete silos are thin shell structures. Shell structures have more complex
patterns of behaviour than any other structural form, they are more sensitive to small errors of
geometry and they have more possible failure modes. As a result, it is common for designers
to oversimplify the problem, and especially to misdiagnose the cause of structural damage.
The subject is very large and only a brief outline is given here. More information may be
found in Rotter (2001a) together with the Eurocodes on metal silos (EN 1993-4-1 2007)
and shells (EN 1993-1-6 2007).
Shell structures tend to suffer serious effects when the pressure is not uniform at one level.
A local drop of pressure can cause serious damage, of different kinds, in both metal and
concrete structures. Where signs of damage are seen, possible causes of loss of symmetry
should be the natural first investigation path to follow.
Static pressures
High pressure
at edge
Static
material
Flowing
Static
channel
A material
Flow
channel
Flow
B
pressures
300
Tensile
200
σz Axial Membrane Stress (MPa)
100
0
A
B
−100 Uniform
B compression
buckling
stress
−200
A
Compressive 216 MPa
−300
−90 −60 −30 0 30 60 90
θ Circumferential coordinate (degrees)
(c) Varying vertical stress around perimeter at A and B (compare symmetric loading value)
Figure 3.23 Flow channel geometry, typical pressure pattern and vertical wall stresses during eccentric
discharge.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:17
Light ring
H/D = 2
Max = R/t = 800 Local
2 × Janssen 2a/H = 0.25 patch
b/H = 0.5
θο = 30° θ
2a μ = 0.4
θο
b
Janssen Buckling
here
Janssen
Example silo
400
High stress may
Vertical membrane stress (MPa)
200
Jenike stress
−100 Patch
Figure 3.24 Stresses resulting from a patch of normal pressure on a thin silo.
unzipping of a complete joint from a single zone of slightly elevated pressure. Larger bolts
in thin plates are more ductile than smaller bolts in thick plates. None of these problems
arises in welded construction.
3.5.2.2 Bursting of the vertical wall Bursting failures are very uncommon and are almost
all found in bolted silos where a joint detail has failed. A careful analysis of the loads and
strengths in different modes shows that this failure mode is only critical near the surface,
or in squat silos.
3.5.2.3 Axial compression buckling of the vertical wall Buckling of the vertical wall
is by far the commonest failure mode in metal silos. The buckles can be huge or quite
local, but all buckles should be treated as very serious because this mode of failure is often
dramatically catastrophic.
Axial compression arises from the friction transmitted to the silo wall by the solids. But
axial compression also develops as a result of unsymmetrical pressures against the silo wall,
caused by shell bending phenomena, which cannot be explained within the space limits here.
An example is shown in Figure 3.24 where a local small patch of pressure on the silo wall
induces high vertical compression (not due to friction) far from the patch. In particular, a
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:17
(a) (b)
Figure 3.25 (a) Flyash silo with buckle arrested by hopper impacting the ground; (b) grain silo en route to
total destruction as grain leaks from a buckled zone.
local loss of pressure can result in large increases in vertical compression stresses far above
the point of pressure loss (Rotter et al. 2006). The location of the buckle is therefore not
always a good guide to the location of the problem.
Buckling under axial compression occurs at very low stresses compared with the mate-
rial strength (perhaps at 20 MPa in a metal with yield stress 250 MPa), and the strength
is very sensitive to small errors of geometry. The post-buckling behaviour is also no-
toriously catastrophic. Two examples, where total destruction has not yet occurred, are
shown in Figure 3.25. The buckles are relatively small, often with a characteristic diamond
shape.
Under high internal pressures, a different form of axial compression buckle occurs, termed
the ‘elephant’s foot’ because of its smooth flat squashed shape. Also, where a buckle occurs
adjacent to a support, a buckle may develop in the local high stress field, needing a more
careful evaluation (the force being transmitted may not be easily determined).
3.5.2.4 Eccentric discharge buckling of the vertical wall A separate section is noted here
for conditions of eccentric discharge. This is the commonest cause of axial compression
buckles, where the low pressures against the wall in the flow channel cause high vertical
compressive stresses over part of the perimeter near the mid-height of the silo (Figure 3.23).
Extremely catastrophic failures are easily produced in tall silos, in which the whole silo
falls over in the direction of the discharge outlet. The analysis of this problem can be found
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:17
in Rotter (1986b, 2001b). The condition is often mistaken as being caused by bending
moments in the wall (Jenike 1967; Wood 1983), and these moments are indeed present, but
bending does not produce diamond pattern buckles. The complex behaviour of cylindrical
shells under unsymmetrical loads is, unfortunately, not widely understood.
The evaluation of the buckling strength under different conditions is quite complicated
and can be found in Rotter (2001a), EN 1993-4-1 (2007) or EN 1993-1-6 (2007).
3.5.2.5 External pressure buckling of the vertical wall When a silo is empty, the thin
wall is very susceptible to buckling under extreme wind. The buckles associated with this
loading tend to be much larger than those for axial compression, usually stretching either
the whole height of the silo or from a plate thickness change up to the top. Similar buckles
occur when a partial vacuum is induced by the discharge of solids of low permeability and
the silo is inadequately vented. For advice, see EN 1993-4-1 (2007).
3.5.2.6 Shear buckling of the vertical wall Where a squat silo (low aspect ratio) is either
eccentrically filled (unsymmetrical top pile producing different heights of solid-wall con-
tact) or is subjected to seismic excitation, the wall can buckle in shear near the foundation.
These buckles have a characteristic diagonal stripe shape, but these load cases are relatively
rare.
3.5.2.7 Rupture, plastic deformations and buckling in hoppers Hoppers made in bolted
construction are susceptible to fracture of the joint at the point where the structural stresses
are most seriously mismatched with the joint strength. The pattern of stresses is not the
same as the pattern of pressures, but in bolted hoppers it is important to adopt a correct
pressure pattern so that these joints are well designed. Once a failure initiates, unzipping
tends to occur, leading to catastrophic failure.
In welded hoppers, failure is much less likely in the hopper itself. Most failures occur near
the top of the hopper, and are either rupture (the hopper is torn off, with unzipping passing
around the perimeter) or plastic deformations. Both situations arise from an excessive total
load on the hopper or from unsymmetrical pressures, not from a high ‘switch’ pressure
at the transition. For design and evaluation advice, see Rotter (2001a) and EN 1993-4-1
(2007).
3.5.2.8 Buckling and yielding in transition rings The transition is subject to high com-
pressions because the hopper has a sloping form. Both buckling and yielding failures can
occur in these rings, but these situations are usually caused by a misunderstanding of the
complex stresses in such rings especially near supports (thrust, bending, torsion and shell
flexure), rather than any special event in the stored bulk solid.
When concrete is subjected to tension, it cracks at right angles to the tension. It is normal
to reinforce concrete to carry the tensile forces, but this reinforcement cannot carry stresses
without stretching (strains), and this same stretching causes the concrete to crack. Cracked
concrete often permits ingress of moisture and may lead to degradation of the stored product.
The simplest solution is to prestress the concrete with steel high strength strand, so that it
is in compression before any load comes on it. Then when additional tensile stresses are
induced in the wall by the stored solid, they simply reduce the pre-existing compression.
Vertical compression does not usually cause problems in concrete silos since the weight
of concrete, the thickness and the good compressive strength all contribute to excellent
strength.
3.5.3.2 Cracking under bending moments The chief problem for concrete silos is
cracking under bending moments induced by unsymmetrical pressures, where a zone of
low pressure occurs inside the silo, the wall bends inwards, cracking on the inside (possibly
not visible without careful inspection), possibly with adjacent regions of cracking on the
outside at the edges of that zone. To prevent serious cracking of this kind, all concrete silo
walls must be designed with some significant bending strength, and this is arranged by using
an inner and an outer layer of reinforcement and requiring the design to support unsym-
metrical loads. In EN 1991-4 (2007), ‘patch’ loads are defined on the silo wall which are
intended to produce similar bending moments in the walls to those that would be produced
by the real unsymmetrical pressure patterns discussed above. However, these patch loads
have not yet been properly calibrated against the outcome of tests on silo pressures, so the
design magnitude is not yet very certain.
Where concrete silos are subject to eccentric discharge, the low pressures in the flowing
solid cause reduced pressures against a limited part of the wall, and the primary effect of
these is to induce vertical cracks associated with circumferential bending. However, the
concrete silo is a shell structure, albeit thicker than the metal silos, and eccentric discharge
has been shown (Rotter 2001c) also to cause cracking in the roof and severe damage to
internal structures simply because the effects of the flow channel low pressure are transmitted
throughout the whole structure.
3.5.3.3 Crack observations As noted above, cracks in concrete are at right angles to the
principal tensile stress, so the orientation of cracks gives a good indication of the stress
state in the wall. Since it is usually only the outside surface that can be observed, care must
be taken to determine whether the cracks are caused by through-thickness tension (very
serious) or external surface tension caused by bending. Diagonal cracks may, for example,
indicate a flow channel of widening dimensions inside the silo.
3.5.3.4 Ductility and delamination Concrete is a brittle material, but most structural
design relies on the assumption that the structure behaves in a ductile manner. Concrete
structures achieve this by appropriate reinforcement, but where forces are applied to the
structure that were not planned for in the design, brittle failures can occur. In particular,
shear failures in concrete walls can cause serious cracking. Another brittle problem is that
of delamination, where splitting occurs along the plane of the reinforcement. This generally
occurs when the concrete is under high compressive stresses.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:17
Figure 3.26 (a) Mechanical discharge with concentric pressures; (b) air injection and air slides promote mass
flow; (c) pneumatic filling of powders causes almost flat top surface; (d) expanded flow hopper gives mass flow
only in the bottom hopper.
There are many different special circumstances that can occur in silos that need special
attention. Several are specifically identified in EN 1991-4 (2007), but even these require an
extensive description for a full explanation. However, a few are briefly noted here so that
the reader can seek further information where it is needed.
The aspect ratio of the silo is a key determinant of conditions, as noted in Figure 3.3.
Where silos have an internal system of discharging (Figure 3.26a), only filling pressures
need to be considered, so simpler safe designs are possible. Where air slides are used in
silos containing powders that can be fluidised (Figure 3.26b), the flow pattern will be mass
flow irrespective of the indications of Figure 3.21: mass flow pressure conditions must be
assumed. Where powders are filled in a condition such that they are fluidised on deposition,
it should be assumed that the top surface will be flat (Figure 3.26c): this matters where the
silo is relatively squat. Where an expanded flow hopper is used (Figure 3.26d), the bottom
part of the hopper is subject to mass flow hopper pressures, but the upper part of the hopper
may be shallow and the base of the cylinder experiences mixed flow, so proper account
should be taken of this.
Internal structures within silos (tubes to assist flow, flow promotion devices such as
Chinese hats and cone-within-cone structures, etc.) may be subject to large forces from
stored solids. Some advice on these may be found in the Australian Standard (AS 3774 1996).
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:17
Finally, where silos may be subjected to seismic loads, much care is needed. In elevated
silos, a huge mass is supported on a relatively soft spring, leading to a low natural frequency
which is easily excited by seismic waves. In on-ground silos, vertical compressions and high
shear forces develop in the walls due to the horizontal excitation (Rotter & Hull 1989), and
care must be taken to ensure that the structure is strong enough, but also to ensure adequate
connection in the base details. Some information may be found in EN 1998-4 (2006).
This chapter has given a brief outline of the key aspects of silo pressure phenomena and
their implications for potential damage to silo structures. It is evident that the subject is large
and requires much more detailed treatment on many issues than is possible here. However,
many references to other useful sources have been given.
Our understanding of silo pressures and their consequences for storage structures is
continually expanding, sometimes as a result of new catastrophes. As a result, current
advice and standards are likely to be steadily improved, and better treatments should be
available for many of the questions that were imperfectly answered here. The reader is
invited to seek specialist advice when new problems are encountered.
Acknowledgements
The author wrote this chapter whilst in Hong Kong as a Royal Society Kan Tong Po Visiting
Professor. The author is most grateful to the Royal Society, the Kan Tong Po fund and the
Hong Kong Polytechnic University for their generous support. The chapter has drawn on
understandings gained in extensive discussions with Dr Jørgen Nielsen and Prof J.G. Teng,
and their contributions are gratefully acknowledged.
References
Arnold, P.C. (May 1991) On the influence of segregation on the flow patterns in silos. Bulk Solids Handling,
11(2), 447–449.
Arnold, P.C. & McLean, A.G. (November 1976) Prediction of cylinder flow pressures in mass-flow bins using
minimum strain energy. J. Eng. Ind., Trans ASME, Ser. B, 98(4), 1370–1374.
Arnold, P.C., McLean, A.G. & Roberts, A.W. (1980) Bulk Solids: Storage, Flow and Handling, Tunra Bulk Solids
Handling Research Associates, 2nd edn. University of Newcastle, NSW, Australia.
AS3774 (October 1996) Loads on Bulk Solids Containers, Australian Standard. Standards Association of
Australia, Sydney.
Chen, J.F., Rotter, J.M., Ooi, J.Y. & Zhong, Z.J. (June 2005) Flow pattern measurement in a full scale silo
containing iron ore. Chem. Eng. Sci., 60(11), 3029–3041.
Dabrowski, A. (1957) Parcie Materialow Sypkich w Leju (Pressures from Bulk Solids in Hoppers). Archiwum
Inzynierii Ladowej, Warsawa, pp. 325–328.
DIN 1055-6 (1964, 1987, 2006) Design Loads for Buildings: Loads in Silo Containers. DIN 1055, Part 6,
Deutsches Institut für Normung, Berlin.
Drescher, A. (1991) Analytical Methods in Bin-Load Analysis. Elsevier, New York.
Elghazouli, A.Y. & Rotter, J.M. (February 1996) Long-term performance and assessment of circular reinforced
concrete silos. Construction Build. Mater., 10(2), 117–122.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:17
EN 1991-4 (2007) Eurocode 1: Basis of Design and Actions on Structures, Part 4 – Silos and Tanks. CEN,
Brussels.
EN 1993-1-6 (2007) Eurocode 3: Design of Steel Structures, Part 1.6: General Rules – Strength and Stability of
Shell Structures. CEN, Brussels.
EN 1993-4-1 (2007) Eurocode 3: Design of Steel Structures, Part 4.1: Silos. CEN, Brussels.
EN 1998-4 (2006) Eurocode 8: Design Provisions for Earthquake Resistance of Structures – Part 4: Silos, Tanks
and Pipelines. CEN, Brussels.
Gaylord, E.H. & Gaylord, C.N. (1984) Design of Steel Bins. Prentice Hall, New Jersey.
Jaky, J. (1948) Pressures in silos. Proceedings of the 2nd International Conference on Soil Mechanics and
Foundation Engineering, Rotterdam, Vol. 1, pp. 103–107.
Janssen, H.A. (1895) Versuche uber Getreidedruck in Silozellen. Z. des Vereines Dtsch Ingenieure, 39(35),
1045–1049.
Jenike, A.W. (1961) Gravity Flow of Bulk Solids. Bulletin of the University of Utah, Vol. 52, No. 29, Bulletin
No. 108 of the Utah Engineering Experiment Station, Salt Lake City, Utah.
Jenike, A.W. (1964) Storage and Flow of Solids. Bulletin of the University of Utah, Vol. 53, No. 26, Bulletin
No. 123 of the Utah Engineering Experiment Station, Salt Lake City, Utah (revised November 1976).
Jenike, A.W. (February 1967) Denting of circular bins with eccentric drawpoints. J. Struct. Div., ASCE, 93(ST1),
27–35.
Jenike, A.W., Johanson, J.R. & Carson, J.W. (February 1973) Bin loads – Parts 2, 3 and 4: concepts, mass flow
bins, funnel flow bins. J. Eng. Ind., Trans. ASME, 95(1, Series B), 1–5, 6–12, 13–16.
Ketchum, M.S. (1907) Design of Walls, Bins and Grain Elevators, 1st edn. McGraw-Hill, New York (2nd edn,
1911; 3rd edn, 1919).
Koenen, M. (1895) Berechnung des Seitenund Bodendrucks in Silos. Zentralbl. Bauverwaltung, 16, 446–449.
Muir Wood, D. (1990) Soil Behaviour and Critical State Soil Mechanics. Cambridge University Press, Cambridge,
England.
Nanninga, N. (November 1956) Gibt die ubliche Berechnungsart der Drucke auf die Wande und den Boden von
Silobauten Sichere Ergebnisse. Die Ingenieur, 68(44).
Nielsen, J. (1998) Pressures from flowing granular solids in silos. Phil. Trans. R. Soc., Lond. A, 356(1747),
2667–2684.
Ooi, J.Y., Rotter, J.M. & Pham, L. (1990) Systematic and random features of measured pressures on full-scale
silo walls. Eng. Struct., 12(2), 74–87.
Pieper, K. & Stamou, K. (March 1981) Lasten in Niedrigen Silos. Lehrstuhl für Hochbaustatik, Technische
Universität Braunsweig, 94 pp.
Pieper, K. & Wenzel, F. (1964) Druckverhältnisse in Silozellen. Wilhelm Ernst und Sohn, Berlin.
Rankine, W.J.M. (1857) On the stability of loose earth. Phil. Trans. R. Soc., Lond., 147, 9.
Rotter, J.M. (1986a) On the significance of switch pressures at the transition in elevated steel bins. Proceedings
of the Second International Conference on Bulk Materials Storage Handling and Transportation, Institution
of Engineers, Wollongong, Australia, pp. 82–88.
Rotter, J.M. (1986b) The analysis of steel bins subject to eccentric discharge. Proceedings of the Second In-
ternational Conference on Bulk Materials Storage Handling and Transportation, Institution of Engineers,
Wollongong, Australia, pp. 264–271.
Rotter, J.M. (1999) Flow and pressures in silo structural integrity assessments. Proceedings of the International
Symposium: Reliable Flow of Particulate Solids III, Porsgrunn, Norway, August 1999, pp. 281–292.
Rotter, J.M. (2001a) Guide for the Economic Design of Circular Metal Silos. Spon, London.
Rotter, J.M. (2001b) Pressures, Stresses and Buckling in Metal Silos containing Eccentrically Discharging Solids.
Festschrift Richard Greiner, TU Graz, Austria, pp. 85–104.
Rotter, J.M. (2001c) Report on Damage to the Raw Meal Silo at Cebu. Technical Investigation Report C01-05,
School of Civil and Environmental Engineering, University of Edinburgh.
Rotter, J.M. & Hull, T.S. (1989) Wall loads in squat steel silos during earthquakes. Eng. Struct., 11(3),
139–147.
Rotter, J.M., Ooi, J.Y. & Zhong, Z. (2006) Critical pressure conditions in silos. Proceedings of the 5th International
Conference for Conveying and Handling of Particulate Solids, Sorrento, Italy, 27–31 August, 6 pp.
Rotter, J.M., Pham, L. & Nielsen, J. (1986) On the specification of loads for the structural design of bins and silos.
Proceedings of the Second International Conference on Bulk Materials Storage Handling and Transportation,
Institution of Engineers, Australia, Wollongong, July 1986, pp. 241–247.
Schmidt, K.H. & Stiglat, K. (1987) Anmerkungen zur Bemessungslast von Silos. Beton und Stahlbetonbau, 9,
239–242.
Teng, J.G. & Rotter, J.M. (1991) The strength of welded steel silo hoppers under filling and flow pressures. J.
Struct. Eng., ASCE, 117(9), 2567–2583.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:17
Walker, D.M. (1964) A Theory of Gravity Flow of Cohesive Powders. Central Electricity Generating Board, UK,
SW Region, R&D Dept, Report No 22.
Walker, D.M. (1966) An approximate theory for pressure and arching in hoppers. Chem. Eng. Sci., 21,
975–997.
Walters, J.K. (1973) A theoretical analysis of stresses in silos with vertical walls. Chem. Eng. Sci., 28, 13–21.
Wood, J.G.M. (1983) The analysis of silo structures subject to eccentric discharge. Proceedings of the Second
International Conference on Design of Silos for Strength and Flow, Stratford-upon-Avon, pp. 132–144.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:19
4 Pneumatic conveying
DAVID MILLS AND MARK JONES
4.1 Introduction
Pneumatic conveying systems are basically quite simple and are ideally suited for the
transport of powdered and granular materials in factory, site and plant situations. The
system requirements are a source of compressed gas, usually air, a feed device, a conveying
pipeline and a receiver to disengage the conveyed material and carrier gas. The system is
totally enclosed, and if it is required, the system can operate entirely without moving parts
coming into contact with the conveyed material.
High, low or negative pressures can be used to convey materials. For hygroscopic ma-
terials dry air can be used, for toxic materials a closed loop system can be used and for
potentially explosive materials an inert gas such as nitrogen can be employed. A particular
advantage is that materials can be fed into reception vessels maintained at a high pressure
if required.
Bulk Solids Handling: Equipment Selection and Operation Edited by Don McGlinchey 135
© 2008 Blackwell Publishing Ltd. ISBN: 978-1-405-15825-1
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:19
4.1.3.1 Dilute phase If the material is conveyed in suspension with the carrier gas through
the pipeline it is referred to as dilute phase conveying. Provided that a material can be fed
reliably into a pipeline almost any material can be conveyed in dilute phase, regardless of
the particle size, shape or density.
4.1.3.2 Dense phase If the material can be conveyed at low velocity in a non-suspension
mode, through all or part of the pipeline, it is referred to as dense phase conveying. In dense
phase conveying two modes of flow are recognised. One is moving bed flow, in which the
material is conveyed as a moving bed on the bottom of the pipeline. The other mode is plug
flow, in which the material is conveyed as full bore plugs separated by air gaps. Moving
bed flow is only possible in a conventional conveying system if the material to be conveyed
has good air retention characteristics. Plug-type flow is only possible in a conventional
conveying system if the material has good permeability.
4.1.3.3 Conveying air velocity For dilute phase conveying, a relatively high value of
conveying air velocity must be maintained. This is typically in the region of 11 m/s for a
very fine powder, to 16 m/s for a fine granular material, and beyond for larger particles and
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:19
higher density materials. For dense phase conveying, air velocities can be down to 3 m/s,
and lower in certain circumstances.
4.1.3.4 Solids loading ratio The solids loading ratio is a useful parameter in helping to
visualise the flow. This is the ratio of the mass flow rate of the material conveyed divided by
the mass flow rate of the air used to convey the material. It is expressed in a dimensionless
form. For dilute phase, maximum values that can be achieved are typically of the order of 15
(15 kg of material conveyed with 1 kg of air), although this can be higher if the conveying
distance is short and the conveying line pressure drop is high.
With moving bed flows, solids loading ratios of well over 100 can be achieved if materials
are conveyed with pressure gradients of about 20 mbar/m of horizontal pipeline. For plug-
type flows the use of solids loading ratio is not as appropriate, for as the materials have
to be very permeable, maximum values are only of the order of about 30. Despite the low
value of solids loading ratio, materials can be reliably conveyed at velocities of 3 m/s and
below in plug-type flow.
A wide range of pneumatic conveying systems are available, and they are all generally
suitable for the conveying of dry bulk particulate materials. The majority of systems are
conventional, continuously operating, open systems, in a fixed location. To suit the material
being conveyed, or the process, however, innovatory, batch operating and closed systems
are commonly used. Many of these systems can be either positive or negative pressure in
operation or a combination of the two. In this chapter some of the more common systems
are presented. With such a wide range and choice of system types, a useful starting point is
to consider the alternatives in pair groupings (Mills et al. 2004):
r Open and closed systems: Open systems are the norm for pneumatic conveying,
particularly when conveying with air. Closed systems would only be employed for very
specific circumstances, such as with highly toxic and potentially explosive materials.
r Positive pressure and negative pressure systems: Materials can be sucked as well as
blown and so either pressure or vacuum can be employed for pneumatic conveying.
This is often a matter of company or personal preference.
r Fixed and mobile systems: The majority of pneumatic conveying systems are in fixed
locations and so this is not identified as a particular case. A variety of mobile systems
are available for specific duties.
r High and low pressure systems: In pneumatic conveying, high pressure typically
means any pressure above about 1 bar gauge. For systems delivering materials to
reception points at atmospheric pressure, 6 bar gauge is typically the upper limit,
due to the problems of air expansion. Very much higher pressures can be employed
if delivering materials to reception points maintained at pressure, such as chemical
reactors and fluidised bed combustion systems.
r Conventional and innovatory systems: Conventional systems are those in which the
material is simply fed into a pipeline and either blown or sucked, and so this is not
identified as a particular case since this is the norm. Innovatory systems are those in
which the material to be conveyed is conditioned in some way, either at the feed point
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:19
or along the length of the pipeline. This is generally in order to convey the material
at low velocity and hence in dense phase, if the material has no natural capability for
low velocity conveying.
r Batch and continuously operating systems: Both of these types of conveying are
common in industry.
r Single and multiple systems: The majority of conveying systems are single units. It is
possible, however, to combine units for certain duties.
r Dilute and dense phase systems: Dilute and dense phase conveying do not relate to
any particular type of system. Any bulk particulate material can be conveyed in dilute
phase. It is primarily the properties of the material that determine whether the material
can be conveyed in dense phase, particularly in conventional conveying systems.
Diverter valves
Filters
Supply
hopper
Blower or
compressor
Discharge hoppers
Negative pressure systems are also widely used for drawing materials from open storage,
where the top surface of the material is accessible. This is achieved by means of suction
nozzles. Vacuum systems, therefore, can be used most effectively for off-loading ships.
They are also particularly useful for cleaning processes, such as the removal of material
spillages and dust accumulations. Another application is in venting dust extraction hoods.
Vacuum systems have the particular advantage that all gas leakage is inward, so that the
injection of dust into the atmosphere is virtually eliminated. This is particularly important
for the handling of toxic and explosive materials or any material where environmental
considerations have to be taken into account. It is not always necessary to employ a closed
system with these materials, therefore, provided that adequate safety measures are taken,
particularly with regard to exhaust venting.
As a result of the conveying air being drawn through the air mover, it is essential that the
exhauster should be protected from the possibility of the failure of one or more of the filter
elements in the gas–solid separation system. This can be achieved by incorporating a back-
up filter. A sketch of a typical negative pressure conveying system operating with a vacuum
Filter
Storage hoppers Air
Air Exhauster
Discharge
hopper
Air
Filter
Exhauster
Flexible
Stock pile
hose
Receiving
hopper
Suction
nozzle
nozzle is given in Figure 4.3. If a high vacuum is used for the conveying of a material,
consideration should be given to the stepping of the pipeline part way along its length. Air
is compressible and the volume increases considerably with decrease in pressure. If the
pipeline is not stepped, extremely high conveying air velocities could occur towards the end
of the pipeline. The situation is the same for high positive pressure conveying systems.
Filter Diverter
Storage hoppers To other
discharges
Vacuume line
Some air movers, such as positive displacement blowers, operate on a given pressure ratio,
and this will mean that the machine will not be capable of operating over the same pressure
range with the combined duty as compared with their individual operation. This will mean
that the system capability is limited in terms of both tonnage and distance. Although there
is only one air mover, two filter units will be required, as shown in Figure 4.4.
Reception silo
Intermediate
vessels
Compressor
Exhauster
Suction nozzle
batch conveying system may be chosen for a specific process need, the mode of conveying
is, to a large extent dictated by the choice of pipeline feeding device. The majority of batch
conveying systems are based on blow tanks, and blow tanks are chosen either because of
their high pressure conveying capability, or because of the abrasive nature of the material.
Two types of system are considered. In one, the batch size is relatively large, and the
material is fed into the pipeline gradually, and so can be considered as a semi-continuous
system. In the other, the material is fed into the pipeline as a single plug.
4.2.7.1 Semi-continuous systems It should be noted that when batches of material are fed
into the pipeline gradually, there is essentially no difference in the nature of the gas–solids
flow in the pipeline with respect to the mode of conveying through the pipeline. This is
certainly the case during the steady state portion of the conveying cycle, regardless of the
value of solids loading ratio.
The blow tanks used vary in size up to 50 m3 or more, generally depending upon the
material flow rate required as well as a need to maintain a reasonable frequency of blow
tank cycling. The material can be conveyed in dilute or dense phase, depending upon
the capability of the material, the pressure available and the conveying distance, as with
continuously operating systems.
With a single blow tank it is not possible to utilise the pipeline while the blow tank is
being filled with material or when the system is being pressurised. Since batch conveying is
discontinuous, steady state values of material flow rate, achieved during conveying, have to
be higher than those for continuously operating systems in order to achieve the same time
averaged mean value of material flow rate. This means that air requirements and pipeline
sizes have to be based on the maximum, or steady state, conveying rate. The intermittent
nature of the conveying cycle is illustrated in Figure 4.6.
In comparison with a continuously operating system, therefore, the batch operating sys-
tem would appear to be at a disadvantage. Blow tank systems, however, can operate at very
much higher pressures to compensate, and twin arrangements in series can be configured
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:19
Maximum or steady-state
One cycle
conveying rate
Time
to operate continuously. It should be emphasised that blow tanks can be operated at low as
well as high pressure, depending upon the system requirements.
If a material needs to be fed into a chemical reactor or a boiler plant that is maintained
at a pressure of 25 bar for example, the blow tank can be designed to operate at 30 bar for
the duty. When delivering material to a reception point at atmospheric pressure, however,
air supply pressures greater than about 6 bar are rarely used. This is mainly because of the
problem of air expansion and the need for a stepped pipeline to prevent excessively high
values of conveying air velocity. A typical batch conveying system based on a single blow
tank is illustrated in Figure 4.7.
4.2.7.2 Single plug systems In the single plug conveying system the material is effectively
extruded into the pipeline as a single plug, although the material is generally well aerated.
It is typically about 10 m long. This plug is then blown through the pipeline as a coherent
plug. A certain amount of material will tail off the end of the plug as it is conveyed, but the
Storage
Filter
hopper
Conveying line
Blower or Discharge
Blow tank compressor hopper
Filter
Supply hopper
Vent
Conveying line
Blow tank
front of the plug will sweep up material deposited in the pipeline by the previous plug. Blow
tanks are generally used as the feeding device and a sketch of a typical system is given in
Figure 4.8.
The air pressure has to overcome the frictional resistance of the plug of material in
the pipeline. As a result blow tank sizes are rarely larger than about 5 m3 , unless very
large diameter pipelines are employed. In terms of system design, a cycling frequency is
selected to achieve the required material flow rate, which determines the batch size. The
pipe diameter is then selected such that the frictional resistance of the plug results in a
reasonable air supply pressure to propel the plug at the given velocity. The material will be
conveyed at a low velocity, in what may be regarded as dense phase, but solids loading ratios
have no significance here, and steady state conveying, as depicted in Figure 4.6, does not
apply either. Single plug systems are capable of conveying a wide range of materials, and
generally at much lower velocities than can be achieved in continuously operating systems.
Many coarse, granular materials are either friable or abrasive and can only be conveyed in
dilute phase with conventional conveying systems, and so single plug systems can represent
a viable alternative, although it would always be recommended that tests be carried out
to confirm this. Material discharge often represents a problem with this type of system.
Although the plugs of material are conveyed at a relatively low velocity, once they are
discharged from the pipeline the high pressure air released behind the plug can cause severe
erosion of the pipeline on venting.
Many bulk particulate materials are transported from one location to another by road,
rail and sea. Many materials, of course, are transported in a pre-packaged form, or in bulk
containers, and can be transported by road, rail, sea or air, in a similar manner to any other
commodity. Many transport systems, however, are specifically designed for bulk particulate
materials and have a capability of self loading, self off-loading, or both. These are generally
mobile versions of the above static conveying systems, depending upon the application and
duty.
4.2.8.1 Road and rail vehicles Road vehicles are widely used for the transport of a
multitude of bulk particulate materials, such as cement, flour, sugar and polyethylene.
Road vehicles often have their own positive displacement blower mounted behind the cab
and so can off-load their materials independently of delivery depot facilities. The material
containing element on the truck can generally be tipped to facilitate discharge, which can
be via a rotary valve, or the container might double as a blow tank that can be pressurised.
Rail cars or wagons generally rely on delivery depot facilities for off-loading. Because
of their length tilting is not an option and so multiple point off-loading is often employed.
They may be off-loaded by rotary valve, or the rail car may be capable of being pressurised
so that it can be off-loaded as a blow tank. Whereas road vehicles are typically designed
to operate with air at 1 bar gauge for this purpose, rail vehicles are usually designed to
2 bar gauge and can generally be off-loaded in about 1 hour. The base of the rail car is
usually angled at about 5◦ in herringbone fashion around each discharge point and fluidised
to facilitate removal of as much material as possible.
4.2.8.2 Ships Large bulk carriers usually rely on port facilities for off-loading and these
are generally similar to that depicted in Figure 4.5. Intermediate bulk carriers, however,
often have on-board facilities for off-loading. Such vessels are often used for the transfer of
materials such as cement to storage depots at ports for local supply, or to off-shore oil and
gas rigs. Materials are typically transferred from storage holds in the ship by a combination
of air-assisted gravity conveyors and vacuum conveying systems, into twin blow tanks. High
pressure air is supplied by on-board diesel driven compressors and materials are conveyed
to dock-side storage facilities through flexible rubber hose, which solves the problems of
both location and tidal movements.
Back-up filter
Heat exchanger
Primary filter
Supply
hopper
Feeder
Reception
Blower hopper
A null point needs to be established in the system where the pressure is effectively
atmospheric and provision for make up of conveying gas can be established there. If this is
positioned after the blower the conveying system can operate entirely under vacuum. If the
null point is located before the blower it will operate as a positive pressure system.
A back-up filter would always be recommended, because positive displacement blowers
and compressors are very vulnerable to damage by dust. This is simply a precaution against
an element in the filter unit failing. There will generally be an increase in temperature
across an air mover and so in a closed loop system it may be necessary to include a heat
exchanger, otherwise there could be a gradual build up in temperature. The heat exchanger
can be placed either before or after the air mover, depending upon the material being
conveyed.
Supply
hopper
Pressure air
To discharge
hopper
Blow
tank
Fluidising air
Air knife
Pulse air
With a need to convey many materials at low velocity, much development work has been
undertaken to find means of conveying materials at low velocity that have with no natural
dense phase conveying capability. The innovatory systems produced as a result of these
developments have centred around some form of conditioning of the conveyed material,
either at the feed point into the pipeline or along the length of the pipeline. Since the
modifications are essentially based on the pipeline, types of conveying system have not
changed significantly.
4.2.10.1 Plug forming systems The pulse phase system was developed in the late 1960s.
A typical pulse phase system is shown in Figure 4.10. An air knife, positioned at the start
of the pipeline, intermittently pulses air into the pipeline to divide the discharging material
into discrete short plugs. Blow tanks are commonly used for the feeding of materials in this
type of system.
No further conditioning of the material occurs along the length of the pipeline. The pulse
phase system was initially proposed as a solution to the problem of conveying cohesive
bulk solids, but subsequent developments have shown that a wider range of materials can
be conveyed successfully.
4.2.10.2 By-pass systems The most common by-pass systems employ a small pipe run-
ning inside the conveying line, having fixed ports, or flutes, at regular intervals along its
length. This inner pipe is not supplied with an external source of air, but air within the con-
veying line can enter freely through the regular openings provided. In an alternative design
the by-pass pipe runs externally to the pipeline and is interconnected at regular intervals.
By this means pipeline bends can also be conveniently incorporated.
If the material is impermeable the air will be forced to flow through the by-pass pipe if the
pipeline blocks. Because the by-pass pipe has a much smaller diameter than the pipeline, the
air will be forced back into the pipeline through the next and subsequent flutes because of
the extremely high pressure gradient, and this will affect a break up of the plug of material
causing the blockage.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:19
External bypass
Internal bypass
Porous tube
Booster line
4.2.10.3 Air injection systems A number of systems have been developed that inject air
into the pipeline at regular points along its length. While by-pass pipe systems artificially
create permeability in the bulk material, air injection will help to maintain a degree of air
retention within the material. Continuous injection of air into the pipeline, however, does
mean that conveying air velocities towards the end of the pipeline will be much higher
as a result. In some systems, sensors are positioned between the parallel air line and the
conveying pipeline and air is only injected when required. If a change in pressure between
the two lines is detected, which would indicate that a plug is forming in the conveying
pipeline, air is injected close to that point in order to break up the plug and so facilitate its
movement. A sketch of various plug control systems, including both by-pass pipe and air
addition methods, is given in Figure 4.11.
Many of the innovatory systems are capable of being stopped and re-started during oper-
ation. With most conventional systems this is not possible, and would result in considerable
inconvenience in clearing pipelines if a blockage should occur as a consequence. Since they
are capable of conveying materials in dense phase, operating costs for power are likely to
be lower than those for a conventional dilute phase system. Capital costs for the innovatory
systems are likely to be higher, however.
All pneumatic conveying systems, whether they are of the positive or negative pressure
type, conveying continuously or in a batch-wise mode, can be considered to consist of the
basic elements depicted in Figure 4.12.
Numerous devices have been developed to feed materials into pipelines, as well as to
disengage materials from the conveying air at the reception point. In vacuum systems
the material feed is invariably at atmospheric pressure and so the pipeline can either be
fed directly from a supply hopper or by means of suction nozzles from a storage vessel
or stockpile. Pressure capability, control and air leakage are important points to consider
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:19
Air and
Clean material Clean
air in air out
Pipeline
Material out
here. A wide range of compressors, blowers, fans and exhausters are also available, but
consideration on choice must be given to the operating characteristics of the machine.
Blow tank
Venturi
Gate valves
Suction nozzle
Trickle valve
Figure 4.13 Approximate operating pressure ranges for various feeding devices.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:19
Material feed
Material inlet port
….
….
…
….
..
… ... .
..….
……
... Housing
…
..
. . Drive
shaft
Rotor
pressure systems there will be no adverse pressure drop across the feeding device, but
a similar problem in terms of air ingress into the conveying system may occur with the
receiving hopper since this will have to be maintained under vacuum. If theses losses or
ingress are significant, the air supply will have to be increased to compensate, for the correct
air flow rate to the pipeline must be maintained for conveying the material.
4.3.1.1 Rotary valves The rotary valve is one of the most commonly used devices for
feeding material into pipelines. This type of feeder consists of a bladed rotor working in
a fixed housing. In many applications in which it is used its primary function is as an air
lock, and so is often referred to as a rotary air lock. It is a positive displacement device and
so material flow rate can be controlled by varying the speed of the bladed rotor. This type
of valve, usually referred to as a ‘drop-through’ feeder, is depicted in Figure 4.14 and is
generally suitable for free-flowing materials.
Material from the supply hopper continuously fills the rotor pockets at the inlet port
which is situated above the rotor. It is then transferred by the motor-driven rotor to the
outlet where it is discharged and entrained into the conveying line. For cohesive materials it
is generally necessary to either profile the rotor pockets, to minimise ‘hang up’ of material, or
to physically purge the material from the discharge side by aligning this with the conveying
pipeline. For pelletised materials an off-set valve, with a side inlet, is generally used in order
to prevent shearing of particles.
By the nature of the feeding mechanism, rotary valves are more suited to relatively non-
abrasive materials. This is particularly the case where they are used to feed materials into
positive pressure conveying systems. By virtue of the pressure difference across the valve,
and the need to maintain a rotor tip clearance, air will leak across the valve. Wear, therefore,
will not only occur by conventional abrasive mechanisms, but by erosive wear also. Air
leakage through the blade tip clearances can generate high velocity flows, which will entrain
fine particles, and the resulting erosive wear can be far more serious than the abrasive wear.
Wear resistant materials can be used in the construction of rotary valves, and removable
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:19
Material
feed Weighted non-
return valve
Rotating
screw
Air and
Drive Air jets material
shaft
Air inlet
lining plates can be incorporated to help with maintenance, but wear can only be minimised,
it cannot be eliminated if an abrasive material is to be handled.
For positive pressure conveying systems it is usual to have a small opening in the side
of the rotary valve so that the air leaking across the valve can be vented. The vented air
is usually directed to the supply hopper above, where it can be filtered, for this air can
carry fine material with it. To increase the pressure capability of rotary valves, end plates
are usually fitted to the rotors and the radial surfaces are provided with seals in order to
minimise the air leakage.
4.3.1.2 Screw feeders Much of what has been said about rotary valves applies equally to
screw feeders. They are positive displacement devices, feed rate control can be achieved by
varying the speed, they can be used for either positive pressure or vacuum feeding duties,
air leakage is a problem when feeding into positive pressure systems, and they are prone
to wear by abrasive materials. For high pressure duties, in order to minimise air leakage, a
variable pitch screw is employed, as illustrated in Figure 4.15.
This high pressure type of feeder, however, is only suitable for fine materials, such as
cement and fine grades of fly ash, that are capable of being ‘compressed’ to a higher bulk
density in the reducing pitch section of the screw, since this is how the ‘air seal’ is achieved.
As a consequence of this the power required to drive the screw is quite high.
4.3.1.3 Venturi feeders Since the basic problem with feeding positive pressure systems
is that the air leakage arising from the adverse pressure gradient can interfere with the flow
of the material into the pipeline, this situation can be improved, to a certain extent, by using
venturi feeders. These basically consist of a reduction in pipeline cross-section in the region
where the material is fed from the supply hopper, as shown in Figure 4.16. It will be seen
that there are no moving parts with this type of feeding device, which has certain advantages
with regard to wear problems, but there is no inherent means of flow control either, and so
this has to be provided additionally.
A consequence of the reduction in flow area is an increase in air velocity and a decrease in
pressure in the region of the throat. With a correctly designed venturi the pressure at the throat
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:19
Material
feed
Flow control
valve
Air and
Air
material
Nozzle Throat
should be the same as that in the supply hopper which, for the majority of applications, is
atmospheric pressure. This then encourages the material to flow more readily under gravity
into the pipeline, since under these conditions there is no leakage of air in opposition to the
material feed. In order to keep the throat at atmospheric pressure, and also of a practical
size that will allow the passage of material and for it to be conveyed, a relatively low limit
has to be imposed on the air supply pressure.
Since there are no moving parts, these feeders are potentially suitable for abrasive and
friable materials. Care must be exercised in using venturis to feed such materials into the
conveying line, however, for the high air velocity in the throat may lead to considerable
erosion and particle degradation in this region. There is no inherent means of flow control
and so this means that the venturi would need to be fed from a belt, screw or vibratory
feeder. A rotary valve could also be used, since there would be no adverse pressure drop
across the valve.
4.3.1.4 Gate lock valves These are probably the least used of all devices for feeding
pneumatic conveying system pipelines. They are variously known as double flap valves,
double dump valves and double door discharge gates. They basically consist of two doors
or gates which alternately open and close to permit the passage of the material from the
supply hopper into the conveying line, as illustrated in Figure 4.17.
To a certain extent the gate lock might be termed an intermittent feeder, since it discharges
material between 5 and 10 times a minute. In contrast, the rotary valve has approximately
150–200 discharges per minute from its pocketed rotor. This reduction in the number of
discharges means that the air supply, in terms of flow rate, and particularly pressure, must
be correctly evaluated to prevent the possibility of line blockage. With few moving parts
this type of feeder can be used to feed friable materials, and with appropriate materials of
construction it is also suited to the handling of abrasive materials.
Material
Flow control Vented air
valve
Gate
Upper hopper
Seat
Gate
Lower hopper
Seat
vacuum cleaner. For industrial applications with powdered and granular materials, however,
the suction nozzles are rather more complex. A sketch of a typical suction nozzle for vacuum
pick-up systems is shown in Figure 4.18. It will be seen that the device has no moving parts
and so a means of controlling material flow rate is critical.
It is essential with suction nozzles to avoid filling the inlet tube solidly with material, and
to maintain an adequate flow of air through the conveying line at all times. To avoid blocking
the inlet pipe, sufficient air must be available at the material feed point, even if the suction
nozzle is buried in the bulk solid material. Indeed, the vacuum off-loading system must be
able to operate continuously with the nozzle buried in the material in order to maximise the
material flow rate. Sufficient air must also be available for conveying the material through
Pipeline
Secondary air
Primary air
Sleeve
a
Material
b inlet
the pipeline once it is drawn into the inlet pipe. In order to achieve maximum conveying
rate it is necessary to maintain as uniform a feed to the line as possible. To achieve this two
air inlets are required, one at the material pick-up point and another at a point downstream.
The conveying pipeline is provided with an outer sleeve at its end, and primary air for
material feed is directed to the conveying line inlet in the annular space created. The length
‘a’ of this sleeve has to be long enough to ensure that it is not buried by the movement of the
material and so prevent the flow of primary air. This sleeve may be many metres long for
ship off-loading applications. The position of the end of the sleeve relative to the end of the
pipeline, ‘b’, is partly material dependent and could be positive or negative. This dictates
the efficiency with which the material is drawn into the conveying line. Secondary air for
conveying the material is generally introduced via a series of holes in the pipeline. Some
form of regulation of both the primary and secondary air is necessary, and the proportion
of the total which is directed to the material inlet is particularly important.
4.3.1.6 Trickle valves Trickle valves, as a device on their own, are only suitable for
vacuum conveying systems, since there is no adverse pressure drop against which to feed.
The greatest problem with this class of feeder is that of flow rate control. A typical device
was shown in relation to the control of the venturi feeder in Figure 4.16. This type of device
is often used because of the cost advantage over almost any alternative method of feeding
vacuum conveying systems. A flow restriction is often fitted into the inlet section of pipeline
to assist with material discharge. This resistance has the effect of slightly lowering the
pressure in the pipeline at the material feed point and so helps to promote flow. There is,
however, no inherent means of flow control and so changes in material properties, such as
particle size and moisture content, could well result in a change in material flow rate.
4.3.1.7 Blow tanks Blow tanks are often employed in pneumatic conveying systems
because of their capability of using high pressure air. Blow tanks are neither restricted to
dense phase conveying not to high pressure use, however. Materials not capable of being
conveyed in dense phase can be conveyed equally well in dilute phase suspension flow from
a blow tank. Low pressure blow tanks are often used as an alternative to screw feeders and
rotary valves for feeding pipelines, particularly if abrasive materials have to be conveyed.
The blow tank has no moving parts and so both wear of the feeder and degradation of the
material are significantly reduced. Another advantage of these systems is that the blow tank
also serves as the feeder, and so the problems associated with feeding against an adverse
pressure gradient, such as air leakage, do not arise.
4.3.1.7.1 Blow tank control In most blow tank systems the air supply to the blow tank
is split into two streams. One air stream pressurises the blow tank and may also fluidise or
aerate the material in the blow tank. This air stream serves to discharge the material from the
blow tank. The other air stream is fed directly into the discharge line just downstream of the
blow tank. This is generally referred to as supplementary air and it provides the necessary
control over the material flow in the conveying line. This is very similar to the means by
which vacuum nozzles are controlled.
4.3.1.7.2 Top and bottom discharge There are numerous different types of blow tank,
and for each type alternative configurations are possible. The basic features of different
blow tanks are essentially similar, but different arrangements can result in very different
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:19
Supply
hopper Conveying line
Blow tank
vent line
Blow
tank Supplementary air
Discharge pipe
Flanged joint
conveying capabilities and control characteristics. The blow tank shown in Figure 4.19 is
typical of a top discharge type.
Discharge is arranged through an off-take pipe which is positioned above the fluidising
membrane. With this type of blow tank, however, it is not possible to completely discharge
the contents, although with a conical membrane very little material will remain. In a bottom
discharge blow tank there is no membrane and material is gravity fed into the pipeline, and
so the contents can be completely discharged. A sketch of such a blow tank is given in
Figure 4.20.
4.3.1.7.3 Blow tank pressure drop The pressure drop across the blow tank represents
a potential source of energy loss to the system and so should be kept as low as possible. In
the case of top discharge blow tanks this is particularly important. The discharge pipe must
be kept as short as possible because the pressure drop in this line will be high owing to the
very high material concentration. Supplementary air should be introduced as close to the
top of the blow tank as possible. With very large blow tanks the discharge pipe should be
turned through 90◦ just above the membrane and be taken through the side of the vessel.
If the discharge pipe is kept to about 2 m, the pressure drop across the blow tank will be
about 0.2 bar, which includes the membrane resistance. In the case of bottom discharge
blow tanks, very short discharge lines can usually be arranged and so the pressure drop is
generally no more than 0.1 bar.
4.3.1.7.4 Twin blow tanks in parallel If two blow tanks are used, rather than one, a
significant improvement in performance can be achieved. The ratio of the mean flow rate
to the steady state material flow rate can be brought close to unity if two blow tanks in
parallel are used. While one is being discharged into the conveying pipeline, the other can
be de-pressurised, filled and pressurised, ready for discharging when the other one is empty.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:19
Vent Material
Hopper
Inlet valve
Blow
tank
Balance line
Discharge valve
Air and
Air material
By this means almost continuous conveying can be achieved through a common pipeline.
A sketch of a typical twin blow tank arrangement is given in Figure 4.21.
4.3.1.7.5 Twin blow tanks in series If two pressure tanks are placed vertically in line
beneath a hopper it is possible to use a high pressure air supply for the continuous conveying
of a material. A sketch of such an arrangement is given in Figure 4.22. The vessel between
the hopper and the blow tank transfers the material between these two, and is effectively a
lock hopper. The vent line is used to release the pressure in the transfer vessel, in addition
to venting on filling.
The lock hopper is filled from the hopper above. The lock hopper is then pressurised to
the same pressure as the blow tank. With the transfer vessel at the same pressure as the
Conveying line
Air supply
Supply
hopper Vent line
Transfer
pressure
Lock hopper
vessel
Conveying line
Pressure balance
and vent
Blow
tank
Air supply
blow tank, the blow tank can be topped up to maintain a continuous flow of material. The
blow tank in Figure 4.22 is shown in a top discharge configuration, but without a fluidising
membrane. The air enters a plenum chamber at the base, to pressurise the blow tank and
fluidise the material, and is discharged into the conveying line. Twin blow tanks, with one
positioned above the other, do require a lot of headroom, and so the blow tank arrangement
shown in Figure 4.22 is sometimes employed to minimise the head required.
If a lock hopper arrangement is used, as shown in Figure 4.22, the pipeline feeding device
need not be a blow tank at all, despite the use of high pressure air. With the transfer pressure
vessel separating the hopper and the pipeline feeding device, the feeding device can equally
be a rotary valve or a screw feeder, for there is little pressure drop across the feeder. The
pressure drop is, in fact, in the direction of material flow and so there are no problems of air
leakage across the device, as there are with conventional feeders of this type. A rotary valve
or screw may be used in this situation to guarantee the feed of a steady flow of material into
a pipeline.
Venturi
Filter bag
Support cage
Gas–solids in
Receiving hopper
Figure 4.23 Bag filter unit with high pressure pulsed air jets.
measures must be taken to prevent its escape into the atmosphere from the handling plant.
This is particularly the case with toxic and explosive materials. The choice of gas–solid
disengaging system to be used on any given application will be influenced by a number of
factors, notably the particle size range of the material.
Where a bulk material consists of relatively large and heavy particles, with no fine
dust, it may be sufficient to collect the material in a simple bin, the solid material falling
under gravity to the bottom of the bin, whilst the gas is taken off through a suitable vent.
However, with a bulk solid of slightly smaller particle size it may be advisable to enhance
the gravitational effect, and the most common method of achieving this is to impart spin
to the gas–solid stream so that the solid particles are thrown outwards while the gas is
drawn off from the centre of the vortex. This is basically the principle on which the cyclone
separator operates. Where fine particles are involved, especially if they are also of low
density, separation in a cyclone may not be fully effective, and in this case the gas–solid
stream may be vented through a fabric filter.
4.3.2.1 Filters The fabric filter is now the industry standard for gas–solid separation
duties in pneumatic conveying systems. With pulsed reverse air jets, on-line cleaning of
these filters is possible, and very compact units are available. A sketch of such a device is
given in Figure 4.23. For batch conveying it may be possible to use a shaking mechanism
to clean the filter bags, rather than the reverse air jets.
The size of a filter, in terms of fabric surface area required, is specified approximately in
terms of the volumetric flow rate of gas to be handled. Filtration plant is designed for steady
state conditions and so if there are likely to be surges and transient effects in performance
due to batch conveying or pipeline purging, for example, these effects must be taken into
account. Filter fabrics will not last forever, and it is important that maintenance schedules
are kept.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:19
Compressors
Particular care must be taken with negative pressure systems. Firstly, it must be realised
that with a system operating under vacuum, the volumetric flow rate of the air to be handled
will be significantly greater than with an equivalent positive pressure system, because of
the compressibility effect. Then consideration must be given to the air mover, because it
has to exhaust the clean air drawn through it, and if this contains any dust, it could cause
considerable damage to the machine if the dust is abrasive.
4.3.3.1 Aerodynamic compressors For high pressure duties centrifugal (turbo) compres-
sors, and especially the multiple stage axial flow type, are normally manufactured only in
large sizes, handling very high volumetric flow rates, and so they rarely find application
to pneumatic conveying installations. The main problem with fans is that they suffer from
the disadvantage that the air flow rate is very dependent upon the line pressure drop. This
is a fundamental operating characteristic for pneumatic conveying, and so this class of
compressor cannot be used reliably.
With a compressor having this type of operating characteristic, it means that if the solids
feed rate to the system should become excessive for any reason, causing the pressure drop
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:19
Axial flow
120 compressors
100
Pressure change (%)
Radial flow
compressors
80
60
Positive displacement
40 compressors
Figure 4.25 Constant speed characteristics of aerodynamic and positive displacement machines.
to increase significantly, the air flow rate may become so low that the material falls out of
suspension, with the risk of blocking the line. Positive displacement machines, for which
the volumetric flow rate is largely independent of the discharge pressure, are less likely to
cause this type of system failure. This point is illustrated in Figure 4.25.
In order to convey materials reliably in pneumatic conveying systems a minimum value
of conveying air velocity must be maintained. For dilute phase conveying this minimum
velocity is typically of the order of 15 m/s, and if it drops by more than about 10 or 20%
the pipeline is likely to block. A small surge in the feed rate into a pipeline of only 10%
would cause a corresponding increase in pressure demand, and with either an axial flow or
a radial flow machine, the reduction in the volumetric flow rate of the air would probably
result in pipeline blockage. On vacuum duties they are often used for cleaning operations.
With waste materials, such as paper, the blades of the fan can be sharpened so that they cut
or chop the material into smaller pieces as it passes through the fan.
Delivery
Intake
compressor, as it can with a fan. Indeed, if the material being conveyed is abrasive, even
dust must be prevented from entering the machine or it will suffer severe damage.
4.3.3.3 Positive displacement blowers Positive displacement blowers are probably the
most commonly used type of compressor for dilute phase conveying systems. They provide
an ideal match, in terms of pressure capability, with the conventional low pressure rotary
valve, and are a typical working combination on many plants. They can be used as vac-
uum pumps, or exhausters, as well as blowers. The principle of operation is illustrated in
Figure 4.26. Twin rotors are mounted on parallel shafts within a casing, and they rotate in
opposite directions. As the rotors turn, air is drawn into the spaces between the rotors and
the casing wall, and is transported from the inlet to the outlet without compression. As the
outlet port is reached, compression takes place when the air in the delivery pressure pipe
flows back and meets the trapped air.
Because of this shock compression the thermodynamic efficiency of the machine is
relatively low and this is one of the reasons why these simple compressors are only used for
low pressure applications. In order to reduce the pulsation level, and the noise, three lobed
rotors, as well as twisted rotors, have been introduced. The performance of blowers would
be enhanced with lubrication, but oil-free air is a general requirement of these machines.
The maximum value of compression ratio with these machines is about 2.3:1. This means
that at sea level (1.013 bar absolute) for blowing the maximum delivery pressure will be
about 1.3 bar gauge, and for exhausting the maximum vacuum will be about 0.55 bar.
4.3.3.4 Sliding vane rotary compressors For medium and high pressure conveying sys-
tems the sliding vane type of rotary compressor is well suited. Figure 4.27 illustrates the
operating principle of a simple single stage sliding vane compressor. It is a single rotor
device, with the rotor eccentric to the casing. Compression occurs within the machine, un-
like the blower, and so the air is delivered without such marked pulsations. It will be seen
from Figure 4.27 that the machine will operate equally well as an exhauster for vacuum
conveying duties.
4.3.3.5 Other types With the other machines highlighted in Figure 4.24, compression
also occurs within the machine. The liquid ring compressor is another single rotor device,
with the rotor eccentric to the casing. This finds widest use as a vacuum pump, partly because
it is able to tolerate low concentrations of dust in the air, unlike any of the other machines.
The liquid ring vacuum pump can reach 600 mm Hg in a single stage and over 700 mm Hg
in two stages. For high pressure air the rotary screw compressor is now in wide use. The
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:19
machine consists essentially of male and female intermeshing rotors mounted on parallel
shafts. Inlet and outlet ports are at opposite ends of the compressor. Oil-free machines can
reach about 4 bar with a single stage, and double this with oil injection. As these machines
are generally free from pressure pulsations it is not usually necessary to operate with an air
receiver, and they do not require special foundations for mounting.
4.3.4.1 Delivery temperature Much of the work energy that goes into compressing air
manifests itself in increasing the temperature of the air. Thermodynamic equations are
available that will allow this temperature to be evaluated. The compression process is
adiabatic, partly because of the speed of the process, and it is far from being a reversible
process. As a result, the temperature of the air leaving a compressor can be very high.
If, for example, air at a temperature of 20◦ C is compressed to 1 bar gauge in a positive
displacement blower, the minimum temperature after compression, for a reversible process,
would be about 84◦ C, and with an isentropic efficiency of 80% it would be 100◦ C. If air at
20◦ C is compressed to 3 bar gauge in a screw compressor it will be delivered at a temperature
of about 200◦ C.
Whether or not the air can be used without being cooled will depend to a large extent
on the properties of the material to be conveyed. The most efficient form of compression
is to carry out the process isothermally, and so cylinders of reciprocating compressors, for
example, would be water-cooled, and if staging was employed for achieving high pressures,
inter-cooling would be employed here as well.
4.3.4.2 Oil-free air Oil-free air is generally recommended for most pneumatic conveying
systems and not just those where the material must not be contaminated, such as food
products, pharmaceuticals and chemicals. Lubricating oil, if used in an air compressor, can
be carried over with the air and can be trapped at bends in the pipeline or obstructions. Most
lubricating oils eventually break down into more carbonaceous matter which is prone to
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:19
4.3.4.3 Water removal As the pressure of air is increased, its capability for holding
moisture in suspension decreases. As the temperature of air increases, however, it is able to
absorb more moisture. If the air is not initially saturated it may well reach the saturation point
during the compression process, or in a following after-cooler. Where air is compressed
isothermally quite large quantities of water vapour can be condensed, and in many cases
the air leaving the compressor will be saturated. In adiabatic compression the temperature
of the air will rise, and because of the marked ability of warmer air to support moisture, it
is unlikely that any condensation will take place during the compression process.
As compression occurs very rapidly, it is quite possible that droplets of water will be
carried through pipelines with the compressed air. Also, if additional cooling of saturated
air occurs in the outlet line, further condensation will occur. The removal of droplets of
water in suspension is a relatively simple process. It is important, however, that water filters
and drains should be carefully maintained, and be protected from frost.
4.3.4.4 Air drying If dry air is required for conveying, a reduction in specific humidity
can be obtained by cooling the air. When air is cooled its relative humidity will increase,
and when it reaches 100% further cooling will cause condensation. Beyond this point the
specific humidity will decrease. If the condensate is drained away and the air is then heated,
its specific humidity will remain constant, but the relative humidity will decrease. This
process is adopted in most refrigerant types of air dryers. These are usually limited to a
dew point of about 2◦ C since drying down to this level of moisture avoids problems of ice
formation and freezing. The driest possible air is obtained from a desiccant dryer. These are
capable of reducing the moisture level to an equivalent dew point temperature of −40◦ C.
Table 4.1 Pipe diameters and wall thicknesses for 4 inch nominal bore pipeline.
Schedule number
Dimensions 10 40 80 160
This will give an approximate value of the actual drive power required. If this is multiplied
by the unit cost of electricity it will give the cost of operating the system. Since power
requirements for pneumatic conveying can be very high, particularly if it is required to
convey a material at a high flow rate over a long distance, this basic model will allow
an estimation of the operating cost per tonne of material conveyed to be made. It must
be emphasised that the model presented in Equation (4.1) is only for first approximation
purposes.
4.3.6.1 Pipelines Decisions do have to be made with regard to the pipeline. Material,
wall thickness, surface finish and steps, all have to be given due consideration, as well as
bends in the pipeline.
4.3.6.2 Wall thickness Pipeline is available in a wide range of wall thicknesses. This is
partly for operating pressure applications and for wear resistance with abrasive materials.
In evaluating conveying air velocity it must be realised that the diameter of a 4 inch nominal
bore pipeline is rarely 4 inches. If an abrasive material is to be conveyed, wear of the
pipeline must be expected. To give the pipeline a longer life, pipe having a greater wall
thickness should be used. Schedule numbers are often used to specify wall thickness. Typical
dimensions for 4 inch nominal bore pipeline, for example, are given in Table 4.1.
If the material to be conveyed is not abrasive at all, a thin-walled pipeline could be suitable
for the duty. Pipeline weight in kg per metre could be added to Table 4.1 and this would
show a marked difference. Lighter pipe sections will certainly make construction of the
pipeline easier, particularly if there are vertical sections to erect.
access can be gained for the necessary changes to be made. With fine particles there is little
tendency for the bottom section of the pipeline to wear preferentially.
4.3.6.4 Pipeline material Although steel is the most commonly used pipeline material,
many other materials are available to suit the conveyed material and duty. It was men-
tioned above that thin-walled pipe would be easier to handle and erect because it is lighter.
Aluminium pipe is often used for this purpose. Because of problems of moisture and con-
densation in pipelines there is always the possibility of steel rusting and contaminating
the conveyed material. In cases where hygiene is important, such as with many food and
pharmaceutical products, the pipeline will need to be made from stainless steel.
Where flexibility is required in a pipeline and this cannot be conveniently achieved with
a combination of straight pipe and bends, flexible hose can be used. Where a single line
needs to feed into a number of alternative lines, and a flow diverter is not wanted to be used,
a section of flexible hose of the steel braided type can be used to provide the link.
Where road and rail vehicles and boats need to be off-loaded, flexible rubber hose is ideal.
It is available in natural rubber and a variety of synthetic materials, and comes in a wide
range of sizes. Flexibility is generally needed in ship off-loading applications with vacuum
systems, and hoses provide the necessary flexibility. Care must be taken if the material is
abrasive and has a large particle size, because the wear rate of rubbers can be excessive
with such materials. Unfortunately, the pressure drop for gas–solid flows through rubber
hose increases with increase in velocity, and more so than for steel pipeline (Mills 2004;
Mills et al. 2004). If a very abrasive material is to be conveyed in a pipeline, consideration
must be given to the use of schedule 80 pipeline or higher. An alternative to this, which is
commonly adopted, is to line the pipeline with basalt. If a better material is required, then
alumina ceramics can be used, but this is likely to be more expensive. A usual combination
is to line the straight pipeline with basalt and use alumina for the bends. Alloy cast iron
pipe can also be used.
4.3.6.5 Surface finish Most pipelines are supplied having a satisfactory surface finish
with regard to frictional resistance to flow. For some materials, such as polyethylene, how-
ever, a particular surface finish is required for the specific purpose of reducing the problem
of ‘angel hairs’, or particle melting, with these materials. An artificially roughened surface
is often specified.
4.3.6.6 Bends Bends provide a pneumatic conveying system pipeline with considerable
flexibility in routing, but are the cause of many problems. Each bend will add to the overall
resistance of the pipeline, and hence to the conveying air pressure required. If the conveyed
material is abrasive an ordinary steel bend could fail within 2 hours. An abrupt change in
direction will add to the problem of fines generation with friable materials, and angel hairs
will be generated in long radius bends with many synthetic materials.
Numerous different bends are available to minimise each of the above problems. Many
of these are made of, or lined with, basalt, cast iron, rubber, etc., and some have a constant
bore and a constant radius, as with conventional bends. Another group of bends that have
been developed have neither constant bore nor constant radius. Some of these bends are
shown in Figure 4.28. Care must be taken in selecting such bends, for account must be taken
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:19
(a) The flow bow (b) The gamma bend (c) The blind tee
Figure 4.28 Some special bends developed for pneumatic conveying systems.
of their suitability for the material being conveyed and the pressure drop across the bend
with that material.
4.3.6.6.1 Blind tee With an abrasive material, the simple blind tee bend shown in
Figure 4.28 will probably last 50 times longer than an equivalent radiused bend. It will
ultimately fail around the inside corner due to turbulence. For abrasive materials, therefore,
it is extremely effective, and can even be made out of scrap material. The blind end of
the bend traps the conveyed material and so the oncoming material impacts against other
material, instead of the bend, and thereby protects it. The penalty is in the increased pres-
sure drop that can result. Another problem with this type of bend is that the material that
is trapped in the dead end of the bend may take a long time to be purged from the bend
at the end of a conveying run. It could not, therefore, be used in pipelines required for the
conveying of perishable and time-limited materials.
4.3.6.6.2 Pressure drop Because of the change in direction, impact of particles against
bend walls, and general turbulence, there will be a pressure drop across every bend in any
pipeline. The major element of the pressure drop, however, is that due to the re-acceleration
of the particles back to their terminal velocity after exiting the bend. The situation can
best be explained by means of a pressure profile in the region of a bend, such as that in
Figure 4.29.
The pressure drop that might be recorded across the bend is quite small, and although
this technique might be appropriate for single-phase flows around bends, it is inappropriate
for gas–solids flow. The particles leaving the bend will be at a lower velocity than that at
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:19
p
Pressure
following bend
Figure 4.29 Pressure drop elements and evaluation for bends in a pipeline.
entry and so they will have to be re-accelerated. The bend was the cause of the problem but
the re-acceleration occurs in the straight length of pipeline following the bend, and so it is
here that the associated pressure drop occurs, and not in the bend itself.
4.3.6.7 Steps If high pressure air, or a high vacuum, is used for conveying a material, it
would generally be recommended that the pipeline should be stepped to a larger bore part
way along its length. This is to cater for the expansion of the air that occurs with decrease
in pressure, and so prevents excessively high conveying air velocities towards the end of
the pipeline.
Figure 4.30 illustrates the case of a high pressure dilute phase conveying system. The
minimum value of conveying air velocity that must be maintained is about 15 m/s, and
60 m3 /s of free air is available to convey the material. The conveying line inlet air pressure is
4 bar gauge. From Figure 4.30 it will be seen that a 125 mm bore pipeline will be required for
these conditions, and the resulting conveying line inlet air velocity will be 16.5 m/s. If a single
bore pipeline is used, however, the conveying line exit air velocity will be about 81.5 m/s.
A velocity of 81.5 m/s will cause considerable damage to any conveyed material and very
serious wear to the plant if the material is only slightly abrasive. By stepping the pipeline
twice, as shown in Figure 4.30, it will be seen that the velocity profile can be kept within
reasonably low limits. The stepping of a pipeline to a larger bore would also be recommended
for high vacuum conveying systems and high pressure dense phase conveying. The stepping
of a pipeline is only dependent upon conveying air pressure and should be undertaken for
any length of pipeline. The stepping of a pipeline is also likely to lead to a significant
improvement in performance of the conveying line (Mills 2004; Mills et al. 2004; Mills &
Agarwal 2001).
4.3.6.8 Valves A number of different valves may need to be used on pneumatic conveying
plant, and a wide variety of different valves are available in the market place. Rotary valves
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:19
81.5
60
56.6
50
Conveying air velocity (m/s)
40
Pipeline
31.8 bore (mm)
28.5
30 25.3
100
20 16.0 17.6 16.5
125
10 150
200
250
0
0 1 2 3 4 5
Air pressure (bar gauge)
Figure 4.30 Stepped pipeline velocity profile for high pressure dilute phase system.
have been considered at length, and are ideal for controlling the feed of material into or out
of a system at a controlled rate. There is, however, a requirement for many other types of
valve, generally to be used for the purpose of isolating the flow. Many of these have been
included on sketches of conveying systems earlier and include discharge valves, vent line
valves and diverter valves.
4.3.6.9 Discharge valves A valve in a conveying line that is required to stop and start
the flow has an onerous duty. Although the valve is only used in either the open or closed
position, and is not used for flow control purposes, particulate material must be able to pass
freely through when it is open. If the control surfaces of the valve remain in the flow path,
as they will with pinch valves and ball valves, they must provide a perfectly smooth passage
for the flow of material through the valve when open. Any small protuberances or surface
irregularities that could promote turbulence in the area would result in a rapid deterioration
in performance. This is particularly the case when the material to be conveyed is abrasive.
Any valve for this duty is also very vulnerable during the opening and closing sequences,
and so these operations should be completed as quickly as possible.
The dome valve is a more recent addition to the list of valves available, but it has been
specifically designed for this type of duty, and is now being widely used in industry. The
valve has moving parts, but these move completely out of the path of the conveyed material
when the valve is open. On closing, the valve first cuts through the material and then becomes
airtight by means of an inflatable seal. The valve can be water-cooled and so it is capable
of handling hot materials.
4.3.6.10 Isolating valves There are many instances where material has to be transferred,
usually under gravity, in batches. The valve is either open or closed and often has to provide
an airtight seal. In the gate lock feeder (Figure 4.17), for example, a pair of valves is required
to operate in sequence to feed small batches of material into a pipeline. Where batches of
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:19
material have to be fed into blow tanks, the valve has to be capable of withstanding the
pressure subsequently applied to the blow tank. Of the valves considered above only the
dome valve would be appropriate for this type of duty. It finds wide use in this application,
particularly with the more difficult granular and abrasive materials.
If the material to be handled is not abrasive, the butterfly valve is ideal. They are reasonably
priced, require very little headroom, are not too heavy, and are reasonably airtight. They are
widely used in the food and related industries and in gate lock feeders. They are, however,
much too vulnerable for use with abrasive materials, since the valve remains in the flow
when it is open. Disc valves, like butterfly valves, require very little headroom, but like
dome valves, they swing completely out of the way of the flow of material. They cut though
the material on closing, but generally rely on the subsequent pressure in the vessel below
to provide the necessary seal. Their suitability for use will depend very much upon the
material to be handled and the application.
Slide valves are the oldest valves in the business, and although they have been improved
over the years, the disc valve is a specific development from it. They take up little space and
are cheap. A particular application is in terms of back-up. If any of the other more expensive
and sophisticated valves fail, and need to be replaced, this can be a very difficult and time-
consuming task if the valve is holding several hundred tonnes of material in a hopper, and
this must be drained out before the valve can be removed for repair or replacement.
4.3.6.11 Vent line valves This is a deceptively easy duty, but if it is on a high pressure blow
tank handling fly ash or cement, the valve will have to operate in a very harsh environment.
The air velocity will be very high, albeit for a very short period of time, but a lot of abrasive
dust is likely to be carried with the air. If the material is abrasive then the choice is between
a pinch valve and a dome valve. If the material is non-abrasive, a diaphragm valve could be
used.
4.3.6.12 Flow diversion Flow diverting is a very common requirement with pneumatic
conveying systems and can be achieved very easily. Many companies manufacture specific
flow diverting valves for the purpose. Alternatively flow diversion can be achieved by using
a set of isolating valves. The most common requirement is to divert the flow to one of
two alternative routes, typically where material needs to be discharged into a number of
alternative hoppers or silos. In this case the main delivery line would be provided with a
diversion branch to each outlet in turn.
There are two main types of diverter valve. In one a hinged flap is located at the discharge
point of the two outlet pipes. This flap provides a seal against the inlet to either pipe. The
pipe walls in the area are lined with urethane, or similar material, to give an airtight seal,
and this provides a very compact and light-weight unit. The other main design operates
with a tunnel section of pipe between the supply and the two outlet lines. This unit would
not be recommended for abrasive materials however. This design should provide a more
positive seal for the line not operating, which would probably make it a more suitable valve
for vacuum conveying duties. A sketch of a parallel tunnel-type diverter valve is presented
in Figure 4.31 to illustrate the method of operation.
Flow diversion can equally be achieved by using a pair of isolating valves, with one placed
in the branch, close to the supply pipe, and the other in the supply pipe, just downstream
of the branch. This can be repeated at any number of points along the pipeline. The main
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:19
disadvantage with this arrangement is that a plug of material will be trapped in the short
section of pipeline not in use, which will have to be blown through when the flow direction
changes. If the conveyed material is abrasive, this method of flow diversion would be
recommended. Either pinch valves or dome valves would need to be employed for the
purpose. With two separate valves, instead of one to operate, care would have to be exercised
with the sequencing when changing flow direction.
4.3.6.13 Flow splitting The splitting of a single line into multiple flow lines generally
requires a specific pipeline layout and so there are few devices available. Flow splitting is
often required on boiler plant, where coal dust might need to be sent to the four corners, and
on blast furnaces, where coal or limestone powder might need injecting at a dozen or more
points around the perimeter. The main requirement is generally that each outlet should be
supplied with material at a uniform rate, despite the fact that the distance to each will be
different. The splitting is best achieved in the vertical plane, with the line sizes carefully
evaluated to provide a uniform balance for each.
There is essentially no limit to the capability or a pneumatic conveying system for the
conveying of dry bulk particulate materials. Almost any material can be conveyed and
high material flow rates can be achieved over long distances. There are, however, practical
limitations and these are mainly imposed by the fact that the conveying medium, being a
gas, is compressible. The limiting parameters are then mainly the economic ones of scale
and power requirements. Conveying capability depends mainly upon five parameters. These
are pipe bore, conveying distance, pressure available, conveying air velocity and material
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:19
properties. The influence of many of these variables is reasonably predictable but that of
the conveyed material is not fully understood at present.
4.4.3 Pressure
Although air, and other gases, can be compressed to very high pressures, it is not generally
convenient to use air at very high pressure. The reason for this is that air is compressible
and so its volumetric flow rate constantly increases as the pressure decreases. In hydraulic
conveying, pressures in excess of 100 bar can be used so that materials can be conveyed
over distances of 100 km with a single stage. With water being essentially incompressible,
changes in the velocity of the water over this distance are not very significant. In pneumatic
conveying, air at a pressure above about 1 bar gauge is generally considered to be ‘high
pressure’. Although the air expansion can be accommodated to a certain extent by stepping
the pipeline to a larger bore, as illustrated in Figure 4.30, this is a complex design procedure.
As a consequence, air pressures above about 5 bar are rarely used for pneumatic conveying
systems that deliver materials to reception points at atmospheric pressure.
12 30
12
Go
16 20
8 1·2
Area 20
10
4 0·8
25
Pressure
0·4
drop (bar) 30
0
0 0.04 0.08 0.12
Air mass flow rate (kg/s)
In a horizontal pipeline the vast majority of the material will flow along the bottom of the
pipeline, rather like water, with air above but carrying very little material. For materials that
have good permeability the material tends to be conveyed in plugs through the pipeline. The
plugs fill the full bore of the pipeline and are separated by short air gaps. As the conveying
air velocity is reduced, the air gap between the plugs gradually fills with material along the
bottom of the pipeline and the plug ultimately moves as a ripple along the top of an almost
static bed of material. As the air flow rate reduces, to give very low conveying air velocities,
the material flow rate also reduces.
Materials composed entirely of large mono-sized particles, such as polyethylene and
nylon pellets, peanuts and certain grains and seeds, convey very well in plug flow. In dilute
phase conveying, nylons and polymers can suffer damage in the formation of angel hairs,
and grains and seeds may not germinate as a consequence of damage caused at the high
velocities necessary for conveying. Because of the very high permeability necessary, air
will readily permeate through the material while it is being conveyed and so maximum
values of solids loading ratio will typically be about 30.
0
0 20 40 60 80 100
Solids loading ratio (dimensionless)
Figure 4.33 The influence of solids loading ratio on the minimum conveying air velocity for the pneumatic
conveying of ordinary portland cement.
be added as straight lines through the origin. The lines of constant conveying line inlet air
velocity can be plotted from basic thermodynamic relationships.
It will be seen from Figure 4.32 that the cement could be conveyed at high values of
solids loading ratio and with low values of conveying line inlet air velocity, and hence in
dense phase. These ‘conveying characteristics’ are typical of those for most fine powdered
materials that have very good air retention. At very low values of conveying line pressure
drop it will be seen that the minimum value of conveying line inlet air velocity for the
cement is about 11 m/s. Everything to the right of this line, at higher velocities, is entirely
dilute phase suspension flow. There is a natural transition between dilute and dense phase
flow, and because of the air expansion the flow can change from dense to dilute phase along
the length of a pipeline when velocities are in the transition zone.
The locus of the line defining the ‘no go area’ for the cement is given in Figure 4.33.
The minimum value of conveying air velocity required for the reliable conveying of the
cement is dependent upon the solids loading ratio, or the concentration of the cement
in the pipeline. As the solids loading ratio of the material increases, the conveying line
pressure required also increases, and so much higher pressures are required to convey
a material in dense phase than in dilute phase. At low velocities, however, problems of
erosive wear with abrasive materials, and particle degradation with friable materials, are
significantly lower. For materials such as cement, power requirements are also very much
lower.
With a limit on air pressure used for conveying, because of the problems associated
with air expansion, dense phase conveying, as a consequence, is additionally limited by
conveying distance. If conveying distance is doubled, for example, for the same air supply
pressure, the value of solids loading ratio will fall by about half. With the same pressure
there will be no need for an increase in air flow rate, but the material flow rate will have
to drop by about half to compensate, since there is no increase in energy to the conveying
system. Since conveying capability is dependent upon both parameters, pressure gradient
is a more convenient term to use and the effect can be shown in Figure 4.34.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:19
30
20
15
10
0
0 40 80 120 160 200
Solids loading ratio
Figure 4.34 Approximate influence of solids loading ratio on conveying line pressure gradient for the hori-
zontal conveying of cement.
For materials that are capable of being conveyed in dense phase, therefore, this capability
will only be possible if the air supply pressure is relatively high or the conveying distance
is relatively short. For low pressure or long distance conveying it will only be possible to
convey a material in dilute phase, even if the material has dense phase conveying capability.
Pressure gradient is simply the ratio of the pressure drop available for conveying, divided
by the equivalent length of the pipeline. For convenience it is expressed in mbar per metre
of horizontal pipeline.
Conveying distance is in terms of an equivalent length in order to take account of vertical
sections and the number and geometry of bends in the pipeline. The reference for equivalent
length is that for straight horizontal pipeline. For flow vertically up a scaling parameter of
two approximately holds, such that the equivalent length is double the actual vertical lift
in terms of straight horizontal pipeline. The equivalent length of bends depends very much
upon the value of the conveying air velocity. A correlation derived for cement and fine fly
ash is presented in Figure 4.35 (Mills 2004; Mills et al. 2004).
24
16
12
0
0 4 8 12 16 20
Conveying line inlet air velocity (m/s)
Figure 4.35 Equivalent length of long radius 90◦ bends for the conveying of cement.
lower because of the high permeability of the material and the very different form of the
conveying characteristics with low velocity dense phase conveying of the material. For the
dense phase conveying of this type of material, therefore, solids loading ratio does not have
the same significance as it does for sliding bed flow.
Solids loading
Conveying line inlet ratio
12 air velocity (m/s) 25
No Go Area
Material flow rate (tonne/h)
1. 6
20
Minimum
8 conveying limit 1. 2 20
15
Conveying line
0. 8
pressure drop 10
4 (bar) 25
0. 4 5
30
0 10 12 15 20
0 0.04 0.08 0.12
Air mass flow rate (kg/s)
12
Solids loading
Material flow rate (tonne/h) No Go Area ratio
Conveying line inlet
air velocity (m/s)
8
Minimum
15
conveying limit 1.6
1.2 18
Conveying line 10
4 pressure drop
0.8 21
(bar) 24
0.4 5
27
30
0
0 0.04 0.08 0.12
only be conveyed in dilute phase suspension flow in a conventional conveying system. The
pipeline was relatively short and the air supply pressure was quite high, but despite the fact
that the pressure gradient was very high, the sugar could not be conveyed in dense phase
and hence at low velocity. High pressure, therefore, is not synonymous with dense phase
conveying.
It will be seen from Figure 4.37 that the minimum conveying air velocity for the sugar
was about 16 m/s. The maximum value of solids loading ratio achieved was just over 15
and so this is quite clearly dilute phase suspension flow conveying. From Figure 4.31, it
will be seen that the cement could be conveyed at a solids loading ratio of about 40 in dilute
phase flow. This is because the minimum conveying air velocity was only 11 m/s and the
cement could be conveyed at a very much higher material flow rate.
With no dense phase conveying capability the operating envelope for the sugar is signif-
icantly smaller than that for either the cement or the polyethylene pellets. For any given
pressure drop and air flow rate the material flow rate achieved for the sugar was also sig-
nificantly lower than that for either the cement or the polyethylene pellets. A comparison
of the performance of a number of different materials conveyed through this same pipeline
is presented in Figure 4.38.
It will be seen from Figure 4.38 that the conveying capability of different materials can
vary widely, and not only in terms of dilute and dense phase conveying. Every material
was conveyed in dilute phase suspension flow and even here there was a 2:1 variation.
Differences are clearly evident between sliding bed and plug modes of dense phase flow but
particularly wide differences exist between powdered materials, having good air retention,
at low air flow rates, and hence low velocities. Copper concentrate might be classified as
‘medium phase’ but this capability was due to the fact that the air retention capability was
not as good as the other finer materials. The coke fines had a lower value of minimum
conveying air velocity than the granulated sugar due to the fact that the material had a very
much wider particle size distribution. It can also be recorded that particle density does not
correlate very well with these materials.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:19
20 Conveying line
pressure drop1.5 = 1.5 bar
Material flow rate (tonne/h)
16
Pearlite
Barite
12 Cement
Flour
8
Copper
concentrate
4 Polyethylene
pellets Coke fines Granulated
sugar
0
0 0.02 0.04 0.06 0.08 0.10
Air mass flow rate (kg/s)
Figure 4.38 Comparison of the pneumatic conveying performance of different materials conveyed under
identical conditions.
With pneumatic conveying performance of materials varying as widely as the sample shown
in Figure 4.38, it is not surprising that the scope and accuracy of computer-aided design
programs is limited. Many manufacturing companies that serve a wide range of industries
generally make a point of listing in their advertising material, a vast number of different
materials that they have experience of conveying. Most reputable manufacturing companies
will have a test facility, specifically for the purpose of testing clients’ materials. This will
generally be offered as a ‘free’ service and the client will be invited to witness the conveying
trials to show that their material can be conveyed reliably.
It is unlikely that the geometry of the test facility will match that of the plant pipeline to be
built, but with the use of appropriate scaling parameters such differences can be accounted
for. With regard to the pipeline these differences include: pipeline bore; horizontal and
vertical lengths; number, location and geometry of bends in the pipeline; and pipeline
material. With regard to conveying conditions, conveying line pressure drop, conveying air
velocity and solids loading ratio of the conveyed material can all have an influence on the
conveying performance of the pipeline. With regard to the conveyed material there is mean
particle size and size distribution, particle shape and particle density. If tests are carried
out with a specific material, it is possible that the computer program will not have to take
particle properties into account, but such a program could not possibly be used for another
material, or even a different grade of the same material, with any degree of reliability.
The potential influence of material grade is illustrated in Figure 4.39, where conveying
data for both a coarse and a fine grade of fly ash are compared (Mills & Agarwal 2001).
Fly ash comes from the combustion of pulverised coal in a boiler. The resulting ash is
mostly carried over with the combustion gases. The coarse ash soon drops out of suspension
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:19
Solids
Conveying line inlet Conveying line
loading ratio
air velocity (m/s) pressure drop
4 6 (bar)
Conveying limit 8 10
160120
24 24 100 80
60 50
16 16
Solids loading ratio
1. 6 30
12 Conveying line 12
14 14
pressure drop (bar)
2. 0 15 16 20
8 8
Conveying 1. 6 18 1. 2
10
limit 20 10
4 1. 2 4
0. 8 5 0. 8
0. 4 0. 4
0 0
0 0.04 0.08 0.12 0.16 0 0.04 0.08 0.12
Air mass flow rate (kg/s) Air mass flow rate (kg/s)
(a) (b)
Figure 4.39 Conveying data for fly ash. (a) Coarse grade; (b) fine grade.
in the economiser and air pre-heater hoppers but the fine ash has to be physically removed by
electrostatic precipitators. Both grades of ash were conveyed through the same pipeline in
Figure 4.38 and it will be seen that the coarse grade had no dense phase conveying potential
at all. There were also very marked differences in material flow rates achieved.
p V̇ = ṁ a RT (4.2)
The inclusion of the characteristic gas constant, R, in this equation means that this equation
can be used for any gas. Nitrogen, carbon dioxide, superheated steam and many other gases
are often used for pneumatic conveying. The following equations, however, are derived in
terms of air only. If any other gas is employed the equations will have to be re-worked with
the appropriate value of R.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:19
p1 V̇1 p2 V̇2
= (4.3)
T1 T2
This applies for any gas and is essentially a continuity equation for the conveying system
and pipeline.
The volumetric flow rate of the air (or any other gas) at any point can be obtained
from:
πd 2
V̇ = × C m3 /s (4.4)
4
p1 d 2 C 1
ṁ a = 2.74 × kg/s (4.6)
T1
This then gives the solids loading ratio as:
ṁ p
φ= (4.7)
3.6 ṁ a
since material flow rate is traditionally expressed in terms of tonne per hour.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:19
Material flow
Conveying line pressure drop (bar) 1.2 rate (tonne/h) 8
0.8
4
2
0.4
Air only
0
0 0.04 0.08 0.12 0.16 0.20 0.24
Air mass flow rate (kg/s)
Figure 4.40 Typical pressure drop relationship for pipeline with material flow.
4fL ρ C2
p = × N/m2 (4.8)
d 2
The friction factor, f , is a function of the Reynolds number, Re, for the flow and the pipe
wall roughness, and can be obtained from a Moody chart. Because air is compressible,
both air velocity and air density will vary along the length of the pipeline and so Equation
(4.8) should be integrated between limits in order to get an accurate value. This would be
recommended in any situation where the air only pressure drop represents a high proportion
of the available pressure drop for conveying, such as for long distance conveying.
It will be seen from Figure 4.40 that there is approximately a square law relationship
between pressure drop and velocity. Conveying line inlet air velocity values, therefore,
should not be too high or there will be an adverse effect on conveying performance, as will
also be seen from Figure 4.40. The conveyed material in Figure 4.40 was a granular grade
of potassium chloride and so was only capable of dilute phase conveying. The pipeline used
was 95 m long, of 81 mm bore, with nine 90◦ long radius bends and was almost entirely in
the horizontal plane.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:19
4.5.6.1 Conveying mode In scaling from one set of pipeline data to another, on no account
should the conveying limits derived for the new pipeline exceed those of the original data,
unless there is positive evidence that the material is capable. This means that the conveying
line inlet air velocity derived should not be lower than that for the data to be scaled. If the
pressure gradient available for the new pipeline is greater than that for which the original
data was derived, the solids loading ratio may be much higher (see Figure 4.34), and hence
a much lower conveying line inlet air velocity may appear possible (see Figure 4.33). If a
material has no natural dense phase conveying potential, however, there will be no possibility
of conveying the material at a lower velocity, and hence in dense phase, if a higher pressure
gradient is available, unless there is a change in the type of conveying system used.
4.5.6.2 Equivalent length The equivalent length of a pipeline is taken in terms of the
length of straight horizontal pipeline. This means that all straight horizontal sections of pipe
in a pipeline can be added together and effectively have a weighting of unity.
4.5.6.3 Vertical pipeline For material flows vertically up the pressure drop will be ap-
proximately double that for horizontal pipeline. For vertically upward pipeline, therefore, it
is recommended that the length of vertically up sections is doubled to provide an equivalent
length (Mills 2004; Mills et al. 2004).
For material flows vertically down the pressure gradient can be positive or negative,
depending upon the value of solids loading ratio at which the material is conveyed. For
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:19
dilute phase flows there is generally a pressure drop for the pipeline but for dense phase
flows, with air retentive materials, there is usually a pressure rise (Mills 2004; Mills et al.
2004). If the pipeline system to be designed has any significant length of vertically downward
flow, great care will have to be exercised with the design process.
It is generally recommended that inclined sections of pipeline, particularly for vertically
upward flow, should be avoided and that only horizontal and vertical sections should be
employed in any pipeline routing. The minimum conveying air velocity required for inclined
pipeline sections can be higher than that for horizontal and vertically up sections of pipeline,
and so are more vulnerable to pipeline blockage. The pressure gradient in such inclined
sections is also generally higher than that for horizontal pipeline.
4.5.6.4 Pipeline bends Data for the equivalent length of pipeline bends was given in
Figure 4.35. Although the data relates to bends having a bend diameter, D, to pipeline bore,
d, ratio of about 24:1, it is generally considered that the relationship holds for D/d ratios
down to about 3:1 (Mills 2004; Mills et al. 2004). Below this, and certainly for blind tees
(see Figure 4.28c), the equivalent length can be much greater.
Although bends provide pneumatic conveying systems considerable flexibility in routing,
there is a considerable penalty to pay in terms of pressure drop, and hence conveying
capability. The equivalent length in Figure 4.35 is in terms of conveying line inlet air velocity
and it will be seen that for dilute phase conveying, bend losses can be very significant. The
total loss due to the bends is the value from Figure 4.35 multiplied by the total number of
bends in the pipeline, and so every effort should be made to keep the number of bends in a
pipeline to a minimum.
Little data is available for 45◦ and other bends. Because the primary impact of the
conveyed material in making the turn is the major cause of the material retardation, and
hence its subsequent re-acceleration (see Figure 4.29), bend angle is not likely to have a
major influence.
4.5.7.1 Pipeline bore If a high material flow rate is required it is likely that a larger
pipeline bore will be needed. This scaling can be carried out independently of equivalent
length. Although a higher conveying line pressure drop will give an improvement in perfor-
mance, it will generally be small in comparison to that which can be obtained by increasing
pipeline bore. If a larger bore pipeline is used there is likely to be an additional bonus, for
the air only pressure drop for the pipeline will be lower, since pipeline bore is on the bottom
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:19
16
Potassium sulphate
0
0 20 40 60 80 100
Solids loading ratio (dimensionless)
line of Equation (4.8). The scaling model for pipeline bore is:
2
d2
ṁ p2 = ṁ p1 × tonne/h (4.11)
d1
3
Air supply pressure (bar gauge)
1
Potassium sulphate
(12 tonne/h)
0
80 100 120 140 160 180 200 220
Pipeline bore (mm)
Figure 4.42 Influence of pipeline bore on air supply pressure for given parameters.
pressure results in the most economical design? Plant capital costs could vary considerably,
for with different pipeline bore and air supply pressures there are differences in feeder types,
filtration requirements and air mover types, apart from widely different pipeline costs, and
so a major case study would need to be carried out. Power requirements, and hence operating
costs, however, are largely dependent upon the air mover specification and so these can be
determined quite easily by using Equation (4.1).
The approximate power requirements for the cases considered are presented in
Figure 4.43. In most cases the power required for the air mover represents the major part
120
Potassium sulphate
(12 tonne/h)
100
Power required (kW)
80
60
40
0
80 100 120 140 160 180 200 220
Pipeline bore (mm)
Figure 4.43 Influence of pipeline bore on power requirements for given parameters.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:19
of the total system power required, although for screw pumps a major allowance must also
be made for the screw drive. Figure 4.43 presents an interesting trend for both of the ma-
terials considered. For the cement the smallest bore pipeline is clearly the best, but for the
potassium sulphate it is the largest bore pipeline.
For the potassium sulphate the decrease in power requirements with increase in pipeline
bore can be explained in terms of the decrease in velocity through the pipeline. With a
conveying line inlet air pressure of 3.2 bar gauge the conveying line exit air velocity will be
about 68 m/s, and this reduces to 27 m/s with the much lower air supply pressure required for
the 200 mm bore pipeline. Pressure drop increases significantly with increase in conveying
air velocity and so the pipeline with the lowest velocity profile will generally give the lowest
power requirement for a material such as potassium sulphate.
For the cement the increase in power with increase in pipeline bore can also be explained
in terms of velocity profiles, but in this case it is values of conveying line inlet air velocity
that are relevant. Since cement is capable of being conveyed in dense phase, the relationship
between minimum velocity and solids loading ratio, as shown in Figure 4.41, dictates. In
an 81 mm bore pipeline the inlet velocity is only 4.2 m/s, since the solids loading ratio is
109. In the 200 mm bore pipeline the solids loading ratio is reduced to 14 and so the inlet
air velocity is 12.0 m/s.
The above relationship holds equally for negative pressure conveying systems. Because
of the natural limit on conveying line pressure drop available, however, the situation is
limited to short distance conveying.
pipeline to a larger bore towards the end of the pipeline should be considered. This point
was mentioned earlier and illustrated for a positive pressure conveying system in Figure 4.30.
Stepping the pipeline will generally result in an improvement in material flow rate, as well
as reducing problems of erosive wear associated with the conveying of abrasive materials,
and reducing problems of material degradation associated with the conveying of friable
materials.
Ideally stepping of the pipeline should be incorporated into the pipeline design process,
but this does require an additional level of iteration. In the cases shown in Figure 4.42, lower
air supply pressures could have been employed for the smaller bore pipelines to achieve the
material flow rates quoted. This would then have resulted in an approximate 30% reduction
in power required in both cases in Figure 4.43 for the 80 mm bore pipeline, gradually
reducing with increase in pipeline bore, and hence air supply pressure.
4.6 Troubleshooting
Despite being very simple in concept, and having been in use for well over 100 years, the
influence of material type on conveying performance is not fully understood. System design
involves the use of compressible flow equations and these are not always understood. The
influence of changing conveying parameters is not always obvious and it is not consistent
either, being dependent upon material properties. Conveying air velocity is the major vari-
able in system design and operation, but it is equally the major element in most operating
problems. If the velocity is too low the pipeline is likely to block. If the velocity is too
high; the conveying potential will be reduced, abrasive materials will cause considerable
damage to the pipeline system, and the pipeline system may cause considerable damage to
the conveyed material.
determined. For coarse granular materials having a mean particle size of about 500 μm, a
narrow size distribution and a particle density of about 1000 kg/m3 , a minimum velocity of
about 16 m/s would be recommended. This will need to be increased for larger and higher
density particles.
A critical parameter in Equation (4.13) is p1 . This is on the bottom of the equation and
so any increase in its value will cause a corresponding lowering of C1 . A pipeline is quite
likely to block, therefore, if the compressor is operated above its pressure rating, even for
a short period of time. It must be stressed that absolute values of pressure must be used
throughout in these equations. If p1 is taken as a gauge pressure, or the pressure at the end
of the conveying line, the design is likely to be seriously in error.
The conveying line inlet air temperature must also be expressed in absolute terms. This
is on the top line of the equation and so if the value is below the design value this could
be a cause for concern. This may occur in winter on start-up if insufficient time is allowed
for the system to warm up. The volumetric flow rate is also on the top line. If a conveying
system fails during commissioning this value should be checked. During use gradual wear
of the air mover may occur and so any deterioration in performance could result in pipeline
blockage after a period of time.
3
Material
No Go Area 2 flow rate
(tonne/h)
1.0 1.0 bar
1
2
1
0
Empty line
0
0 0.02 0.04 0.06 0.08 0.10 0.12 0.14
Air mass flow rate (kg/s)
Figure 4.44 Typical performance data for material conveyed in dilute phase.
terms of drifting into the ‘no go area’. A problem that can arise, however, with systems
in which the material flow rate may be varied, is that of crossing into the ‘no go area’ at
low material flow rates, and illustrated with case 4. With no change in air flow rate and a
lowering of material flow rate, the solids loading ratio will reduce. If the operating point
drops below the transitional line on Figure 4.33, the pipeline will be prone to blocking under
these conditions.
Material 8
conveying limit
2.0
6
Conveying line pressure drop (bar)
3
No 4
4
Material flow
rate (tonne/h)
Go 2
1.0
Area 0
Empty line
0
0 0.02 0.04 0.06 0.08 0.10 0.12 0.14
Air mass flow rate (kg/s)
Figure 4.45 Typical performance data for material with sliding bed dense. Phase conveying capability.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:19
Material
Hopper
Vent
Housing
Leakage
.
air (VL)
Rotor
Blower . . .
Note : VC = VS VL
. .
Supply air (VS) Conveying air (VC)
60
1.0 40
30 Solids loading
Conveying ratio
15 20
limit
15
Material flow rate (tonne/h)
0.8
10
10
0.6
5
0.4
5 Conveying line
pressure drop
(bar) 0.2
0
0 0.05 0.10 0.15 0.20 0.25 0.30
Air mass flow rate (kg/s)
Figure 4.47 The influence of a gradual reduction in conveying air flow rate on system performance.
in the air flow rate available for conveying to compensate, pipeline blockage is likely to be
the ultimate result, as illustrated in Figure 4.47. The same situation will occur if there is
gradual wear and deterioration in performance of a compressor or exhauster as a result of
ingesting abrasive dust laden air.
Air
Storage silo
or hopper
Discharge
hopper
Air Air–solids flow
dilute phase conveying, changes in performance can happen quite quickly. If, on start-up,
the pressure gauge rapidly reaches the compressor pressure, the pipeline is likely to be
over fed. Similarly the pressure gauge will indicate if the pipeline is under fed. Ideally
the pressure gauge should be in the conveying line, but this is too arduous a location for
reliability. Just prior to the feeder in the air line is a more reliable location and the pressure
drop across the feeder is not likely to be a significant percentage of the total.
A particular note of the pressure reading should be taken when air only flows through the
pipeline. This value should be checked periodically because it should not change with time.
If it does increase over time it might be due to a gradual build up in the pipeline. If this is
allowed to continue it could ultimately result in pipeline blockage, since the increase in air
only resistance could use up any safety margin available. This may be due to condensation
in the pipeline. If dry air is not used for conveying it would be recommended that air be
blown through the empty pipeline for a short period to dry it out, just in case, before starting
to convey material.
Air intake
Storage
hopper
Exhauster
Discharge
hopper
Air
Figure 4.49 Air by-pass for checking performance of a negative pressure conveying system.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:19
pressure conveying system the t-piece would be positioned between the compressor and
feeding device. In either case it is suggested that there should initially be no change to the
compressor or exhauster. By opening the control valve with the negative pressure system,
air will be drawn into the system close to the exhauster inlet and so by-pass the conveying
line. In a positive pressure system the air would be discharged from the system just after
the compressor and so also by-pass the conveying line.
If the system continues to perform reliably with a small proportion of air by-passing the
system, the valve can be opened a little more. Observation of the pressure gauge, in terms
of degree of fluctuation, should give some indication of when the air flow rate is getting
close to the minimum value. If the air flow rate so by-passed reaches about 10% of the rated
value it would be recommended that the speed of the air mover be reduced to compensate
and the process continued. If too much air is by-passed in this way the system could be
susceptible to premature blockage, for if a pressure fluctuation occurs this is likely to cause
considerably more air to flow through the by-pass, as a line of least resistance.
If the volume of air drawn in or discharged could be measured at each adjustment of
the control valve, together with the material flow rate and conveying line pressure drop, a
small part of the operating characteristics could be mapped for the system. Equation (4.13)
should be used to calculate a value for the conveying line inlet air velocity for reference.
A sight glass in the conveying line, just downstream of the feeding device would also be
useful as this would give a good indication of the system performance.
4.6.7.1 Impact angle and surface material The curve shown in Figure 4.50 illustrates
the variation of erosion with impact angle for two different surface materials. Both surface
materials showed very significant differences in both erosive wear rate and the effect of
impact angle. These materials do, in fact, exhibit characteristic types of behaviour that
are now well recognised. The aluminium alloy is typical of ductile materials: they suffer
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:19
0.4
Erosion (cm3/kg) aluminium
0.06
Particle
0.3
3
∝
0.02
0.1 Surface material
0 0
0 30 60 90
Impact angle (∝) degrees
maximum erosion at an impact angle of about 20◦ and offer good erosion resistance to
normal impact. The glass is typical of brittle materials: they suffer severe erosion under
normal impact but offer good erosion resistance to low angle, glancing impact.
The vertical axis on Figure 4.50 is in terms of the volume of material eroded, in cm3 , per
kg of particles impacted against the surface. It will be seen that both are extremely important
variables and that they should be given due consideration in the design and specification of
the system and its components if an abrasive material has to be conveyed. Erosive wear of
straight pipeline is not generally a problem with powdered materials since particles tend to
flow in almost straight lines at high velocity and impact angles are very low. With granular
materials impact angles are higher, and as the slope of the line on Figure 4.50 for ductile
materials is very steep at low impact angles, ordinary steel pipeline is not likely to be
satisfactory for abrasive materials. This is particularly the case at the outlet from bends in
the pipeline where there is considerable turbulence in the flow. With large abrasive particles,
gravity will also play a part, and severe wear along the bottom of the pipeline is likely to
occur.
Bends in pipelines are particularly vulnerable. Long radius bends will give a low impact
angle, but not low enough to allow mild steel to be used if an abrasive material has to
be conveyed. Short radius mild steel bends cannot be recommended either unless they are
significantly reinforced, but as a consequence of gradual wear, deflecting flows are likely
cause even more problems downstream. This point is illustrated with the wear and flow
patterns for a long radius bend in Figure 4.51.
The ultimate solution to the wear problem is to use a blind T-bend, as illustrated in
Figure 4.28c. Material is trapped in the blind end of the bend and primary impact is material
upon material. The bend will ultimately wear out downstream due to the turbulence, but
this is generally straight pipeline and so a short length of thick wall pipeline can be used
to prolong life. There are two major problems, however. One is that the material trapped in
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:19
Horizontal
Vertical
Flow direction
Figure 4.51 Typical pattern of deflecting flows following erosive wear of a bend.
the bend will take a long time to purge out if the pipeline has to be cleared of material, and
hence the bend shown in Figure 4.28d. The other is that the pressure drop for such mitred
bends is generally significantly higher than that for radius bends and so the performance of
the conveying system could be seriously reduced as result of their use.
4.6.7.2 Velocity The model for the erosive wear of pipeline bends in terms of velocity is:
Erosion ∝ (Velocity)2.5 (4.14)
This means that bends at the end of a single bore pipeline, with a 1 bar pressure drop,
for example, will be more than five times that of bends at the start of the pipeline. This is
another reason for using stepped pipelines to keep the velocity profile along the length of a
pipeline as low as possible, consistent with always keeping above the minimum value for
the given material and conveying conditions.
bends is a possibility here, if the use of such material is compatible with the material to be
conveyed. Rubber can also be used to reduce erosive wear, particularly with fine particles.
Rubber is a resilient material and so is capable of absorbing the energy of impact. As
a consequence both the damage to the particles and the damage to the rubber itself will
be reduced. If the energy of impact, however, is above the threshold for the rubber, due
to particle velocity, size or density, rubber will wear rapidly if the material is abrasive. A
particular advantage with rubber is that the material is flexible and can be rotated when used
for bends and so the life can be prolonged.
References
Mills, D. (2004) Pneumatic Conveying Design Guide, 2nd edn. Elsevier Butterworth Heinemann, Amsterdam.
Mills, D. & Agarwal, V.K. (2001) Pneumatic Conveying Systems – Design, Selection, Operation and Trou-
bleshooting with Particular Reference to Pulverised Fuel Ash. Trans Tech Publications, Clausthal-Zellerfeld,
386 pp.
Mills, D., Jones, M.G. & Agarwal, V.K. (2004) Handbook of Pneumatic Conveying Engineering. Marcel Dekker,
New York. (Note that this book is in US Engineering Units)
Nomenclature
5 Screw conveyors
LYN BATES
5.1 Introduction
The ubiquitous screw conveyor used in countless industries for moving virtually all types and
condition of bulk materials is a descendent of the oldest form of a continuous mechanical
conveyor in recorded history. The principle of moving a material by a helical screw is
attributed to Archimedes (287–212 BC) for elevating water from the hold of a King Hiero
of Syracuse ship. The simplest form of Archimedes’ screw consists of a pipe in the shape
of a helix with its lower end dipped in the water. As the device is rotated the water rises up
the pipe by gravity flow in the separate helical sectors. Equipments based on similar helical
principles have been used since ancient times for raising water to irrigate fields, operated
manually, by animals, wind power and more recently by electric and internal combustion
engines. An alternative construction of a helical blade within a circular casing forms a
more compact volumetric transfer device and this form of rotating casing is now commonly
employed for long kilns and rotary driers as the drive and support bearings are external to
the product conveyed. This method is widely employed for irrigation and sewage handing,
although generally now using a rotating screw within a static, close-fitting casing.
The basic transport mechanism is that the material resting between two adjacent screw
flights on the same axis is promoted to slip down the face of the ‘rising’ side of the flight as
the screw rotates. This action moves the product forward at the rate of one pitch per rotation
of the screw, provided the material does not spill over the centre shaft to fall back into the
proceeding pitch space as when the cross-sectional loading exceeds the height of the centre
tube or the machine axis is excessively inclined.
It will be apparent that the angle of the blade to the horizontal must be greater than the
angle of slip of the media on the flight face for this motion to occur. It is also clear that the
dynamic repose condition attained by the moving media determines the transfer capacity of
a given screw geometry. With a non-viscous liquid, such as water, surface slip will occur at a
very shallow angle and, for screw that is rotating slowly, the surface profile will be virtually
horizontal. Inclination of the screw axis therefore allows a free-flowing liquid to be elevated
by inclining the screw axis but the axial transfer capacity reduces with inclination because
the reduction in effective flight face inclination reduces the volume of the pocket of liquid
that can be held between the flight pitches before spilling back over the centre shaft. The
awkward geometry of the skewed, ‘orange-segment’ shape of the moved volume of an
inclined screw is analysed in ‘The Design of Archimedean Screw Conveyors’, a small, but
useful, publication of the now defunct Draughtsman and Allied Technician Association.
Many hundreds of years passed before the need arose to handle other than water in a
continuous mechanical manner. The demand to process large quantities of grain from the
newly exploited vast American plains led to the mechanisation of flour mills, an early type
of which is thought to have been made by Evans around 1742. His grandson, Oliver Evans,
built a fully mechanised mill in 1785 that included belt conveyors, bucket elevators and a
Bulk Solids Handling: Equipment Selection and Operation Edited by Don McGlinchey 197
© 2008 Blackwell Publishing Ltd. ISBN: 978-1-405-15825-1
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:20
form of screw conveyor that used a series of wooden blades fixed in a helical pattern around
a central wood shaft. These blades were later replaced by formed metal sheet section.
The successful operation of this equipment found many replications and a supply industry
was created to make such conveyors available for wider use.
Screw flights were, and still are, produced from circular discs with a hole in the centre,
being split across one radial width and the helical form created by pressing the two edges
apart with a twisting action, to form slightly more than a complete pitch. These sections
were initially riveted together on a wooden shaft or steel tube to form a continuous helix.
The proportions of the original blank may be calculated on the basis of equal stretch of the
inner and outer periphery during forming, to require minimum work input to the metal. The
final flight stretches to slightly more than one pitch around the shaft and can be ‘snapped’
onto the shaft into a stable location for the butt welding and welding to the centre shaft. A
rough approximation of the size of the blank diameter and inner hole for a standard flight
form of pitch equals outside diameter of the screw can be calculated on an ‘equality in
peripheral length’ basis:
where DB is the outside diameter of blank; DF is the outside diameter of final flight; P is
the pitch of flight; dB is the diameter of hole in blank; dF is the diameter of screw shaft or
tube.
The flight does not usually need to be continuously welded to the centre shaft in order to
transmit the torque required to move the material. A few short runs of ‘stitch’ weld per pitch
are normally quite adequate for strength purposes. Continuous welding is, however, often
specified to eliminate crevices and small residue pockets in the flight corners for hygienic
reasons or to oppose the onset of fatigue by eliminating stress concentrations. It should
be noted that the alternating tensile and compressive stresses that are created as the shaft
rotates are a major source of fatigue failure. This is because screw conveyors in regular
use rapidly attain the number of revolutions, and hence stresses cycle range, where fatigue
is a major factor of the metallic strength. As stainless steel is especially prone to fatigue,
special weld preparation, surface finish and mechanical treatment of the surface of welds
may be undertaken on screws that are considered vulnerable or of strategic importance
in a plant. Many other criteria influence the surface finish of stainless steel (Bates, 1999,
www.ajax.co.uk), the contact friction of the material handled against the face of the screw
flight being an important design parameter.
A means of making a continuous helical flight from a strip of steel was patented in 1898 by
Frank C. Caldwell (US patent 601429). This process allowed extended lengths of continuous
screw flights to be produced quickly and cheaply, and was quickly adopted for use in standard
screw conveying machines. The concentration and growth of other manufacturing industries
during the industrial revolution drove users to employ screw conveyors for handling other
materials than agricultural products, from base mineral products and chemicals to refined
powders and processed food products. The main virtues and limitations of this ubiquitous
tool were rapidly established, usually by practical trials, and design refinements incorporated
until it became a major form of bulk material handling equipment, particularly in the process
industries where materials need to be moved relatively short distances between operations.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:20
Screw conveyors are but one class of screw type solids handling device, albeit a major
form in industrial applications. Other types of helical screw-based solids handling ma-
chines are commonly described as ‘screw feeders’, ‘screw elevators’, ‘hopper discharge
screws’ and ‘metering screws’. Many forms of processing operations also utilise helical
screws in their composition and many of the features described will equally apply to their
operating circumstances. The boundaries between these classes are often blurred, as ma-
chines with a predominant characteristic of one form of machine may undertake some of
the functions combined with broad performance features of others. For the convenience,
it is useful to classify the machine according to the principal mode of mechanics utilised
to promote the movement of the product. However, where more than one mechanism pre-
vails, each section should be examined and appropriately designed within the composite
entity.
The mechanism prevailing in a ‘screw conveyor’ is the ‘gravity’ mode of sliding down
the inclined surface of the screw flight. An essential feature of this process is that the level
of cross-sectional fill is less than 45%. The material progresses along the screw axis one
pitch distance for each revolution of the screw (Figure 5.1).
Dynamic repose
Slip face
Travel
Residue layer
Feed
Slip on casing
A ‘screw feeder’ invariably has a flooded inlet such that the cross section of the screw has,
in principle, a 100% fill, although there may be minor regions of voids behind the working
surface of the flight according to the filling efficiency of the flow system. The movement
of material along the screw axis follows a helical path according to the helix angle of the
screw and the angle of friction between the bulk material and the flight contact surface in a
confined condition (Figure 5.2).
A ‘screw elevator’ works in a dynamic mode, Figure 5.3, with material swirling around
the screw axis and advancing along the axis in a similar pattern to a screw feeder, except
that:
1 The level of fill is limited by the in-feed conditions and back-leakage, so rarely exceeds
25% of the swept volume of a pitch space.
2 The unconfined state of the bulk material allows significant dilatation of the bulk and
the product moves in a vortex pattern with radial shear due to differential velocities
at dissimilar radii.
3 There is boundary leakage in the flight tip clearance space that detracts from the
elevating rate.
A prime determinate of the handling capacity of the screw elevator is the inlet conditions,
where product has to enter tangentially with sufficient radial pressure to overcome the
tendency of the screw and its prior contents to resist inwards movement. As the feed system
is normally a conventional loading hopper leading into an inclined chute, only relatively
free-flowing materials are able to develop sufficient transverse pressure to secure a practical
degree of cross-sectional fill. Various techniques are employed to supplement the feed
pressure, such as a ‘flinger disc’ facing the elevator inlet or a separate horizontal screw feeder,
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:20
Tip leakage
Vortex formed by
rotation of material
Wall slip
which then incorporates additional benefits such as enlarging the feed hopper capacity
(Figure 5.4).
Standard sizes of screw, casing and component details are now readily available for general
use and equipment for simple applications can be specified by non-experts from guidance
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:20
Close
coupled
transfer
The deflection, δ, of a screw supported at both ends in simply supported bearings is:
5 WL3
δ= (5.2)
384 EI
where W is the total weight of the screw; L is the length between bearings; E is the modulus
of elasticity; I is the moment of inertia of pipe or shaft.
Excessive screw deflection may sometimes be avoided by using a larger pipe or one
with a thicker wall. A larger diameter tube is generally more effective and economic, but
the proportions of the screw flight should not be distorted by the use of standard pitches
with very shallow flight up-stands or high compressive states may be induced in the pitch
contents. For long conveying distances, a more positive way to avoid excessive deflection or
the need for intermediate bearings is to use two or more single span machines in a cascade
arrangement. Whilst this approach incurs a higher initial cost, it is often more economical
in applications that demand reliable operation with minimum maintenance.
It is therefore necessary to understand the limitations of this class of equipment perhaps
even more than the many and varied advantages that can be exploited. These mainly depend
on the intrinsic nature of the bulk material that is to be handled, therefore the first task of
an engineer faced with the selection of equipment for a solids handling duty is to recognise
those features that may give rise to unsatisfactory operation.
The engineer’s second task in the process of conveyor specification is to be scrupulously
diligent in investigation-relevant physical properties of the product under the full range
supply and operating conditions pertaining whilst in the equipment. For this work, it is
essential to recognise that the name of the material is rarely an adequate guide as to how the
material may behave. A ‘representative sample’ may also be misleading, as it is necessary
to deal with all conditions that may be offered. A ‘representative sample’ may reflect a
typical condition, but only a single condition and not necessarily the ‘worst’ that has to be
handled. Likewise, all ambient, process and operating variations must be known.
It is vital for reliable operation that the physical properties of the bulk material are known
and within the capability of the screw to handle. An I.Mech.E document (I.Mech.E. 1994)
outlines the interesting aspects of a bulk solid that should be determined in all bulk solids
handling applications.
1 They are normally totally enclosed, protecting the product from contamination and
the local environment from dust and spillage by containment of dust, vapours, gasses
and internal or external pressure.
2 They are of compact cross section because they have only one working element that
does not require a return path.
3 They are flexible in capacity up to their maximum transfer rate, which is essentially
self-limiting, preferably with suitable flight variation between the feed region and
the conveying length. Their potential as a feeder is widely exploited and offers a
great number of benefits when properly integrated with a feed hopper design.
4 Intermediate inlets and outlets of various sizes can be fitted.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:20
5 Different sizes, loading and materials of construction and surface finish may be used
to serve applications that demand strict levels of hygiene or to deal with corrosive,
hot or abrasive products.
6 A screw is reversible, to deliver in either direction from a central inlet, or right- and
left-hand flights can be mounted on the same shaft to bring products to a central
outlet from two inlets or deliver to two outlet at the same time from a central inlet.
7 Can deal with lumpy products and, with suitable flight construction, deal with wet,
damp, cohesive or sticky products, filter cakes, centrifuged products and the like.
8 May be equipped with heating and/or cooling jackets, have heat transfer fluid through
the centre shaft and through special flight constructions.
9 Can incorporate mixing elements of flight variations to undertake continuous mixing
and blending duties.
10 May be designed for dust suppression or liquor addition, surface coating or agglom-
eration.
11 Compacting or pre-breaking functions can be undertaken.
12 May be inclined for elevation and de-watering applications.
Against these, and other uses for these versatile machines, must be recognised some general
limitations to avoid misapplications.
duties can generally be reliably sized and assessed for power requirements, many
forms of screw equipment for feeding, elevating, compacting, mixing and other pro-
cess duties require specialised knowledge or representative tests to prove their per-
formance. Many mechanical designers have limited experience of particulate solids
technology, powder testing and bulk processing; hence some forms of screw equip-
ment are best undertaken by specialist manufacturers.
Within this balance between the advantages and limitations of screw equipment, empirical
developments and advances in the technology are expanding the frontier of applications for
both standard and custom-built machines.
‘Custom’-designed conveyors take two forms. Standard components and their variants
can be assembled in many ways to satisfy specific lengths and inlet and outlet requirements,
to tailor a conventional conveyor to suit a specific installation. The other extreme is an
individually designed machine that incorporates special features or techniques to be purpose-
built for a particular function or duty. The cost of the latter type may be significantly more
than a unit constructed from standard components but, as with many items involved in the
handling of bulk solids, reliable and efficient performance is paramount. Notional savings on
capital cost can involve losses that far exceed any purchase cost difference if the equipment
does not work well.
the inclination to the horizontal of the flight face adjacent to the shaft with the same screw
is only about 38◦ . Materials with a high value of wall friction will tend to be lifted in this
region by centre tube friction and corner effect between the flight and the tube and carried
over the shaft to a previous pitch space. Fortunately, the area a region’s cross section is
linearly related to the diameter, so the dominant conveying area is the most effective region
at the outer portion of the screw flight.
Based on a normal max screw conveyor loading of 45%, the max transfer volume for the
standard flight ratio of pitch equals screw diameter, is given by:
Effective conveyed volume per revolution = 0.45 × 3.142/4[D 2 − K 2 ]P (5.3)
where K denotes whichever is the largest of d or D × Tan × w ; D is the screw diameter;
P is the flight pitch; d is the shaft or tube diameter; w is the wall friction of the bulk
material on the flight face.
Within the normal operating range of screw conveyors the transport velocity is linearly
related to the cross-sectional loading and the rotational speed, the speed generally being
limited by considerations of wear with abrasive materials and the condition of the bulk for
other applications.
Screws are essentially volumetric devices, so it is necessary to know the ‘effective bulk
density as conveyed’, to convert the volume to a mass-based value. Product moved by a screw
is usually in a state of mild agitation, rather than displaced as a coherent mass, therefore
the effective density for conveying purposes tends to be less than when the material is in
a settled condition. This particularly so with fine powders that entrain air when disturbed,
so a useful guide to the effective density that a bulk material will attain when conveyed
by screws to shake a small sample of known weight in a jar and check the instantaneous
volume that it occupies when deposited into a container. The bulk condition attained at
slow speeds of rotation equate to instantaneously settled conditions of an agitated product.
Higher speeds of rotation induce more agitated bulk conditions. This may not be significant,
other than its effect on bulk density when conveying horizontally, but when the machine
is used at an inclination the loose state of fine powders will leak back down the conveying
axis to seriously impair the transfer capacity.
Back
spillage
Leakage at
tip clearance
2 Material spills over the shaft back into the previous pitch space due to the lowering
of the effective angle of the central region of the flight from below the angle of
slip.
It must be remembered that the normal inclination of the inner diameter of the flight adjacent
to the centre shaft is only about 38◦ when the screw axis is horizontal, so at 20◦ slope of the
conveyor this surface reduced to about 18◦ to the horizontal, a slope at which many bulk
materials will not slip on metal surfaces, apart from the drag induced by the centre tube
and sharp corner between the flight and the tube. This also indicates how surface friction of
the material on the flight face is a crucial design parameter, particularly for inclined screw
conveyors (Figure 5.5).
At operating angles steeper than about 25◦ to the horizontal, the situation deteriorates
even more rapidly. Above this inclination material can also start to slide back in the casing
clearance, particularly at the sides where the combination of slope angle with the radius
of the casing forms a steeper wall surface than the screw axis (Figure 5.6). The position is
aggravated by the bias of cross section fill produced by the rotation of the flight, which is
intensified at steeper inclinations by the extra drag induced by the flatter flight. The potential
to elevate material by the conventional mechanical mode of sliding down the face of the
screw flight effectively ceases at axis inclinations above around 35◦ .
It is possible to run a conveyor screw at steeper inclination at low speeds, but the cross-
sectional loading rapidly attains a virtually full condition and the mechanics of transfer
changes radically to that of a screw feeder. In these circumstances the material is acted
on by the circumference of the screw flight and restrained from rotation with the screw by
the frictional drag of the outer casing. Back leakage is prevented by the lack of space for
the material to pass into and the torsional loading increases significantly compared with a
horizontal screw conveying action.
Apart from the heavy torque demands, the main operating drawbacks to this form of
elevating are that the full screw resists feed at the inlet, so the machine will only work
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:20
n
tio
lina
g inc
sin
Ca Slope of
the axis
with free-flowing products and a well-designed inlet chute, and the machine will not clear
of product, remaining full when material ceases to be fed into the machine. This form of
operation is not recommended, except for relatively short units that are not sensitive to
permanent residue.
Material can be carried at a steep angle by a screw elevator, where the screw is surrounded
by a circular casing and runs at a faster speed, but this introduces another different mode
of conveying, where rotation of the mass as a dynamic vortex is retrained by friction
on the casing wall and a degree of back leakage is an acceptable loss of the material
transfer capacity. The selection and specification of screw elevators is generally the domain
of specialists, partly because the number of variables involved in dealing with industrial
applications require the machines to be custom-built. The other main reason is that reliable
operation is very sensitive to the bulk material properties and equipment geometry. There
are two exceptions to the generalisation. Agricultural screw augers are made in standard
sizes to handle grain and other products on the basis of ‘proof by trial’. Some units are built
into machines, such as combined harvesters and agricultural driers. Stand-alone machines
are also user on farms and like duties.
Another crude form of screw elevator is the so-called flexible screw elevators. The very
limited flexibility these machines possess is permitted by the use of a plastic tubular casing
and continuous screw flight that does not have a centre shaft. These units mainly have small
diameter ‘coreless’ screws, i.e. without centre shafts, running at relatively high speeds.
A more recent development, an astonishingly long overlooked innovation in view of the
maturity of the basic screw technology and its international application on a massive scale,
is the ‘static screw elevator’, invented by Peter Olds in Maryborough, Australia, in 2004.
The patented technique exploits the peripheral drag of the boundary layer held in a vertical
casing by virtue of its rotation, whilst product is promoted to move up a static helical
screw by the boundary contact friction. The process is somewhat similar the mechanic of
a conventional screw elevator, except that there is no agitated vortex causing internal shear
in the material in transit and no leakage in the boundary layer between the screw and the
casing. These operating advantages are supplemented by numerous convenient installation
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:20
features, probably the most valuable being the exceptional low pick-up facility and the lack
of a bottom seal and bearing, which are a perennial service problem with most ordinary
screw elevators. Further details of this remarkable machine are given elsewhere (Bates
2005).
The drive of a screw conveyor must overcome the torsional resistance of an empty screw,
the work content of moving the material and the restraint offered by shearing over a bed
of residue in the flight tip clearance space. An allowance must also be made to deal with
starting and for exceptional operating conditions that may arise during the lifetime of the
equipment. However, the mechanics of the machine, which may be of a considerable length
and working under a light or no load condition, permits all the available excess power and
overload capacity of the drive to be concentrated at any point, or on the final flight, should
a local jam or blockage occur. Were such a situation likely to cause damage to the screw or
other items, it is prudent to incorporate a detection or protection device.
L × D2 × S × B
kW loss = (5.4)
200 × E
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:20
where C is the mass moved, Te/h; L is the effective conveyor length, m; is the friction
angle between product and flight face.
The energy content of the ‘shear’ component of the conveying power is given by:
where C is the mass moved, Te/h; L is the effective conveyor length, m; is the internal
angle of friction of the product handled.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:20
There are two essential elements to a screw feeder, a supply hopper and a dispensing screw.
At one end of the spectrum screws are employed to discharge bulk storage silos and hoppers,
sometimes in multiple banks. The rate and accuracy of dispensation may or may not be
important in such cases, but the primary function is to ensure a reliable and controllable
discharge. Usually at the smaller end of the scale, feed screws are required to provide
a definitive discharge rate, with an accuracy determined by the application needs. These
machines may have a large or continuous re-supply system, but more often comprise a
relatively small, integrated hopper that is replenished as required.
criteria towards the radial flow values, according to the degree of transverse convergence.
A typical basic screw feeder is shown in Figure 5.7.
The first step in the design of any bulk storage container is to determine the optimum
flow regime that is to be formed when discharge occurs. The basic choice is ‘mass flow’,
‘expanded flow’ or ‘non-mass flow’, often called ‘core’ or ‘funnel flow’. These patterns are
described in detail elsewhere (University of Florida 1999). ‘Mass flow’ is mainly selected
to avoid indeterminate storage time with products that deteriorate with age or segregate.
‘Expanded flow’ is selected for poor flow bulk materials and ‘core flow’, i.e. all other flow
patterns, for products that are unchanged by storage time and generally free flowing.
The benefits and drawbacks of mass flow are summarised in Table 5.1.
Having selected the appropriate form of flow regime to suit the application, the next
stage is to complete a systematic design process, such as in Figure 5.8, to determine the
proportions of the hopper, key dimensions and the type of discharge control that is suitable:
(i) Generating extraction over the full outlet area of a storage container. It is crucial
for mass flow that extraction takes place over the total screw feeder inlet area.
Progressive extraction at the screw feeder inlet is not essential for non-mass flow installa-
tions and applications where the container is totally empties before being refilled but is useful
to provide at least a degree of progressive extraction on long feeder screws to reduce the
drive power requirements and avoid extended length of ‘dead’ material over the outlet slot.
Progressive extraction can be secured on feeder screws in many different ways. An early
form of generating continuous extraction was by tapering the outside diameter of the screw
along the inlet length of the feeder. This is effective in its objective, but has various operating
and commercial drawbacks. The major practical issue is that the width of the screw varies
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:20
Benefits Drawbacks
Notes: It is essential that flow occurs over the total area of the hopper outlet.
The flow velocity is not uniform across converging sections of the hopper.
Final portion of the discharge can concentrate segregation.
‘Expanded flow’, i.e. mass flow at the outlet region only, secures the outlet size benefits of
mass flow and may suffice for bins that refill at a low level.
‘Mixed flow’, i.e. where the non-mass flow channel expands to the container walls below the
stored surface level. This can appear to be mass flow, but is not generated ‘kick’ stresses on
the walls at indeterminate locations.
Conical hoppers require walls approximately 10◦ steeper than Vee hoppers.
Additional benefits of lower wall angles and smaller outlets may be gained by relaxation of
the transverse flow channel to a slot outlet, provided that the slot develops fully live flow.
over the length, so the effective outlet width for flow is the smallest diameter. The cross-
sectional area of the screw increases as the square of the diameter, so the extraction is not
even unless the pitch is reduced, which is usually contrary to practice and would lead to
problems of deep pocket spaces between the flights. Whilst this progressively increase in
extraction may be acceptable in general use, it has the effect of taking more from the outlet
end of the inlet. It is this location that determines the discharge rate so, as the container
will preferentially empty at this end, the discharge will progressively be controlled by the
reducing size of the screws that are covered with product.
A further drawback of this construction is that it is not convenient to have a taper outlet
slot on a container so the practice is to slope the feeder casing from the screw diameter to a
parallel hopper outlet size that matches the largest diameter of the screw. All most invariably,
this results in a casing wall inclination at the smaller end of the feeder that is inadequate
for product slip. In combination with the gap at the side of the screw to the casing wall that
fills with static product and opposes wall, the effect is to create a narrow flow channel with
non-mass flow characteristics. The economics of manufacture also detract from widespread
adoption of this technique as both the screw and the casing have taper components that
demand extra fabrication time.
The simplest of providing progressive extraction is by way of pitch variation. This has
very strict limits because very short pitches form deep and narrow pockets between the
screw flights that are ineffective in conveying and tend to ‘log’, that is completely fill the
pitch space with product. On the other hand, the mechanics of the screw flight limits the pitch
length when the helix angle of the flight causes excess product rotation with the screw. It is
rarely effective to increase the screw pitch to a dimension greater than the screw diameter.
Incremental transfer of product along the screw axis can cease prior to attainment of this
pitch length and is certainly much reduced at longer pitches. It should also be noted that
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:20
Homogeneous?
Does the powder vary? Consistent?
Stable? Quick test Select flow regime
Established
No Yes
Treat the Mass flow Select 'live' extraction feeder
powder
Design for mass flow Design for mass flow
Control Size for flow rate & or non-mass flow or non-mass flow
environment Hopper capacity*
Review the balance of design for structural integrity and optimum cost *Lyn@ajax.co.uk
the initial section of screw flight exposed to the product as the start of the feeder inlet will
virtually fill with material, so subsequent extraction is dependent on the marginal gain in
axial transfer capacity.
These features tend to limit the effective length of feeder inlet for a mass flow application
to about four screw diameters when the pitch only is varied. This construction is, however,
effective on long screws, where intermittent changes of pitch will relieve the shear under a
‘dead’ region of flow and require less torque to shear through a length of flowing media.
A more effective progressive extraction construction is to make the centre shaft taper from
a large diameter at the start of the feeder to a small diameter at the discharge end. Denial
of the central region is relatively ineffective at small diameters, because the area concerned
is proportional to the square of the diameter. Best results are secured with changing the
pitch as a uniform pitch would require a shallow flight face to promote the motion of a long
annulus of product. This method can utilise a uniform inlet slot and parallel casing, but is
relatively expensive to manufacture. It is well justified on long feeder screws, where the
combination of pitch increase and tube size reduction can be changed to a pitch variation
only at a point along its length. A more economical design is to employ a ‘stepped shaft’
and variable pitch construction that can serve length to width ratios up to around 8 or 10.
(ii) Providing a large, effective outlet size. The use of a screw feeder inevitably offers
a slot shape of outlet, which is equivalent in flow generating terms to a circular
outlet twice the width of a slot. It also provides a flat side for the hopper connection,
and the plane flow channel of a V-shaped hopper can be about 10◦ less inclined for
mass flow than a conical hopper. Twin or multiple screw feeders are often used to
service wide hopper outlets that may be required to countering a tendency to arch,
either with mass flow or non-mass flow hoppers. These work best with progressive
discharge, but will also extract material from under an arching condition until the
arch size is unstable and collapses, provided the critical arching size is less than the
area of the screw feeder inlet. If this situation repeats over a period, the static regions
will be subjected to time consolidation and the design must allow for any such gain
in strength when the remaining material has to be emptied from the hopper.
Multiple small screws offer many operating benefits over single or fewer large discharge
screws. They take considerably less power, less headroom and give a much smoother dis-
charge. They are, however, more expensive because of the multiple bearings and seals,
extra drive train and profiled casing but, in general, the choice is usually very clear as the
penalties of using very large screws can be quite high. Multiple drives can also be useful
to facilitate discharge in the event of a screw or drive problem or offer feed rate change for
finer discretion on batch fill duties.
D × L × (H1 + H2 ) (5.7)
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:20
extra to the volume of the storage capacity for each extra screw, where L is the
length of screw feeder inlet; H1 is the depth of converging V section; H2 is the
depth of hopper body section.
(iv) Feed control. A screw feeder not only provides the facility to control on/off and the
volumetric rate of discharge, but also allows some discretion on where the material
is delivered in relation to the centreline of the storage hopper. It is often convenient,
for example, to discharge into a process vessel, vehicle or subsequent conveyor that
would not readily fit under the storage container. Variable speed drive permits a
range of discharge rates to be easily adjusted to suit the requirements, be integrated
with process control or provide a fast initial discharge and slow trimming feed to
accurately dispense batch weights.
(v) Multiple discharge locations. Good hopper shapes are commonly spoilt by fitting
an extra outlet to the side of a cone section of a hopper. This introduces eccentric
flow and regions of ‘dead’ storage when the original outlet is not in use. Feed
screws can be made reversible, to deliver to either of two locations, which is a
useful facility provided only to one discharge point is in use at any one time.
Another inhibiting feature of this technique is that the screw must be made with
uniform pitch construction to avoid compacting the contents when reversed. This
limits the ‘live’ extraction length of a feeder to about two exposed pitches with a
standard form of screw construction. This does not allow the full slot benefit to be
secured as the slot length should beat at least three times the width to overcome
end effects for mass flow. A proprietary method has been devised to overcome this
limitation. A further refinement by the same company developed the technique of
utilising twin cantilever-mounted screws, facing end to end in the same casing. By
arranging the individual drives to run at half speed of the partner when operating
in the reverse direction, two standard forms of screw will serve a slot length of
four screw diameters with progressive extraction from the full length of the feeder
inlet when operated to discharge to either end outlet independently or to both
end outlets at the same time. Incorporating the above ‘Lynflow’, slot enhancing
technique, allows the effective ‘live’ inlet of a screw to be up to six screw diameters
long and able to serve two outlets independently or together, securing both the full
flow benefits of a slot construction with the extra capacity and flow benefits of a V
form of hopper construction in the crucial outlet region of a storage hopper.
(vi) Enhanced discharge rate and counter ‘flushing’. A problem encountered with the
handling of fine powders is that the change in voidage from a dilated to fully settled
condition, and vice versa, involves the passage of the ambient media, usually air,
through a mass of tortuous interstitial passages to bring the void pressure to ambient
conditions.
This time for this process to attain equilibrium may be extensive, particularly in warm
or hot conditions as the viscosity of air decreases with temperature. The phenomenon of
‘flushing’ is directly related to the presence of excess air in the voids of a mass of fine
particles that sustains a pressure that prevents a more intimate particle-to-particle contact
for the development of shear strength. The contrary condition arises when the bulk is well
settled. The bulk must initially expand to commence to flow though a hopper outlet by
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:20
gravity. All the expansion must be given by enlargement of the void space that has very
limited initial air content. Expansion is, therefore, inhibited by the differential pressure of
ambient and that of the void space in the expanding bulk and satisfying this void demand
of expansion is resisted by the narrow passages between the particles through which this
air has to pass. The tendency is for a slow, but progressive arch to collapse above the outlet
until the arch size attains a dimension larger than the ‘critical arching span’ for the strength
of the bulk solid. At this point there is a dramatic collapse of the arch and the falling mass
can either entrain air to flush uncontrollably through the outlet or fill the void of the arch
for the cycle to repeat. Either event is not conducive to controlled discharge.
Enlarging the effective area of flow by means of fitting a screw feeder with an elongated
slot reduces the rate of expansion and gives more time for the bulk to attain a gravity
flow condition in a controlled manner. Similarly, the larger flow channel generated in the
supply hopper gives more time for air to settle from an initial fluidised state to a stable feed
condition. In this context it is important to note that a non-mass flow hopper will enable
a short-circuit route to develop for fresh material in a fluidised condition to emerge at the
outlet through a deep bed of stored bulk material. Such a hopper has a relatively small cross
section of flow channel through a bed of static material and the residence time for fresh
material is relatively short. This not only gives little opportunity for the material to de-aerate,
but also the high product flow velocity is counter-flow to the rising gas of de-aeration and
tends to take the trapped air down with the bulk to maintain the loose condition.
Even a mass flow hopper has a significant velocity gradient across the converging section
of the container and can preferentially draw-down fluidised material through the bed if this
velocity differential reaches near the surface. The reason is that flow pressures of a fluidised
mass are hydrostatic, whereas the lateral pressures of gravity flow of a normal media are
much less than the vertical pressures. A depression in the flow channel that admits a bulk
material in a fluid condition will therefore exert radial pressures mush in excess of the
non-fluid product and progressively penetrate the flow channel. To counter this tendency,
the cross section of the live flow channel should be as large as practical and have minimum
velocity differences. Alternatively, an accelerated de-aeration device should be fitted in the
centre of the flow channel.
Empty and running conditions may be generally ignored when sizing the power requirements
of a screw feeder because the main load to be faced is starting conditions, where the screw
has to commence rotating in a settled bed of confined bulk material.
It must be emphasised that this duty is completely different to the sizing of a screw
conveyor drive as the bulk material is subjected to a compacting overpressure at the feeder
interface and completely surrounds the screw. Determination of the effective pressure acting
on a screw feeder inlet is beyond the scope of this book as it is influenced by the hopper
geometry and filling conditions, but a crude assessment may be given by considering the
effective compacting load, CL , to be of the order of:
CL = 2W × L × γ (5.8)
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:20
where W is the width of slot; L is the length of slot; γ is the compacted density of
product.
The shear strength, f s , then equals to CL × tan δ, where δ is the internal angle of friction
of the bulk.
The effort required to rotate the screw is that needed for the inclined face of the flight face
to shear the bulk at the peripheral radii of the flight and also move the weight of the screw
contents along the screw axis. It will be seen that the effort will differ along the axis for a
variable geometry screw flight, but a conservative rating can be attained by considering the
longest pitch construction to apply along the full length and the shear stress to apply around
the whole circumference of the screw. A separate assessment may necessary for the section
of screw projecting beyond the inlet region if, as is usually the case, the screw geometry is
changed after the inlet section to dilate the material to avoid wasting energy. This portion
can be considered as a highly loaded screw conveyor, only requiring to move the contents
of the screw.
The torque, T , required to turn a pitch section of a feeder screw is therefore:
T = f s D/2[sin(tan−1 P/π D + tan−1 ϕ)π DP + π/4(D − d 2 )Pγ ] (5.9)
where f s is the shear strength of product; D is the flight diameter; P is the flight pitch; φ
is the contact friction angle of material on flight face; γ is the bulk density of the product.
The axial thrust, A, generated by this pitch length is:
A = f s [cos(tan−1 P/π D + tan−1 ϕ)π DP + π/4(D − d 2 )Pγ ] (5.10)
A major use of screw feeders is for controlling the rate of feed on powders and bulk materials
to batch or process operations. Feed rates from many tonnes per hour down to less than a
kilogramme per hour are quite common. Lower feed rates are generally more demanding
of design in order to secure reliable flow and an even rate of dispensation. This is partly
because low feed rates demand small diameter screws, and hence narrow widths of flow
channel that may experience flow difficulties. Also, low feed rates usually mean low screw
speeds and the evenness of discharge may be affected by cyclic variations because of the
screw geometry, or erratic fluctuations due to the avalanching of the slope of free-flowing
products or ‘cohesive breakaway’ of materials that are not free flowing.
Screw feeders are essentially volumetric discharging devices and used solely as volu-
metric dispensers are widely used for the controlled metering of bulk solids. They have to
be calibrated to secure a specific mass flow rate and, for stable accuracy, depend on the
product being handled flowing reliably and in a consistent state of density. Screw feeders
can sustain uniform accuracy, typically within ±2% of a set figure, when dealing with a
firm, granular material, assuming that the screw speed is steady and no changes take place
in the product. It is not unusual for finer limits to be held with hard-grained, free-flowing
materials. The main virtue of volumetric feeding is that it is considerably more economical
than when the additional cost of gravimetric control is added and is perfectly satisfactory
for many applications where fine accuracy is not important. Screw speed change can be
exercised on volumetric feeders for example, manual control of a batch dispensation can
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:20
change from a high to low discharge rate to provide fine discretion on fill quantity or simple
feedback provided by some process control to adjust the supply to an optimum rate.
The main drawbacks of volumetric feed control are:
(i) Feed rate deviations cannot be detected or automatically rectified should they occur
(ii) Density variations do occur in many bulk products, particularly fine powders
(iii) Accuracy cannot be guaranteed or held to fine limits
(iv) It is not possible to record the actual rate of feed
When dealing with relatively high value products, sensitive formulations or a traceable
record is necessary, a gravimetric system is virtually essential.
A popular technique is the loss-in-weight system, whereby a batch load of product is
filled into a hopper equipped with a weighing device and the reduction in weight, measured
at very frequent intervals, is compared with the change that should have occurred according
to a pre-set value. Corrective action is applied by changing the screw speed to swiftly
compensate for any deviation to ensure that the feed rate does not fall outside close limits.
When the contents of the supply hopper reduces to a low level the feeder control alters from
gravimetric to a fixed speed for a short period, the fixed speed being based on the immediate
past controller experience, during which period the hopper is refilled. There is sufficient
product in the feeder flow channel to meet the discharge quantity during the re-fill period,
after which the feeder resumes gravimetric control that can compensate for any density
difference between the refill material and that previously held.
In some cases it is more convenient and/or accurate to weigh the receiving vessel, as
this may have a lighter tare value and permit finer load cell discretion. Feedback control
may also be derived from process conditions, such as heating of reactors or ability of the
process machine to accept product. Advances in load cell design and control technology
has considerably improved the capability of gravimetric feeders to deliver an accurate feed
rate. It remains that no electronic wizardry can compensate for unpredictable variations
in bulk density, as may occur in non-mass flow hoppers. An efficient system demands
that the material arrives at the screw, not only reliably, but in a consistent bulk density
condition. Much can be done in the way of advanced hopper design to promote reliable
flow through narrow flow channels and condition the product to a consistent bulk density
condition.
A variety of special features can be incorporated in screw feeder design to secure op-
erating convenience, easy-clean facilities, compacting, force feeding against a resisting
pressure, providing a ‘seal plug’ against vapours, heat, contamination and the like. A novel,
proprietary technique to generate progressive axial extraction with a uniform pitch construc-
tion screw has been developed by Ajax Equipment Ltd. Within their Lynflow trademark
of innovative techniques that exploit fundamental principles within state-of-art technology.
Users and designers of screw conveyors and feeders continue to find new, novel, innovative
and efficient applications, so the subject is far from a complete technology.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:20
References
Ajax Equipment Ltd. (1998) ‘Lynflow’ Slot Enhancing Technique for Uniform Pitch Screw Feeders.
www.ajax.co.uk.
Bates, L. (1999) The Surface Finish of Stainless Steel. Ajax Equipment Ltd. www.ajax.co.uk.
Bates, L. (October 2005) The static screw elevator. Proceedings of the 8th International Conference on Bulk
Materials Storage, Handling and Transportation, University of Wollangong.
Forcade, M.P. (1994) Screw Conveyor 101, Basic Training Manual for Screw Conveyors. Goodman Conveyor
Company.
I.Mech.E. (1994) Guide to the Specification of Bulk Solids for Storage and Handling Applications. Bulk Materials
Handling Committee.
University of Florida (January 1999) Flow regimes in bulk storage hoppers. In: Educational Resources for
Particulate Technology, Vol. 1, No. 1, Art 3.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:21
6 Trough conveying
DON MCGLINCHEY
6.1 Introduction
On a superficial level the concept of the bulk solids chute resembles a playground slide.
Its apparent simplicity, however, does not guarantee trouble-free operation or sympathy
to careless design. The basic chute design may be viewed as a surface, set at a sufficient
angle to the horizontal to overcome friction by the effect of gravity alone (see Figure 6.2).
There is an added complication in that bulk solids also have an internal friction angle to be
considered.
Bulk Solids Handling: Equipment Selection and Operation Edited by Don McGlinchey 221
© 2008 Blackwell Publishing Ltd. ISBN: 978-1-405-15825-1
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:21
Trough Tube
The pressures on the walls of the chute, see Figure 6.3, can be approximated as the
hydrostatic case if the depth of the bed is less than the width of the chute.
σ = ρb g H (6.1)
A more complete description of stresses in confined bulk solids is given in Chapter 3 and
is used in the analysis described later in this section.
Chutes may be used to transfer material from one process vessel to another, from storage
into a process vessel or as an intermediate between one transport system to another or
from storage to a transport system. They can be used ‘on-axis’ or be used to redirect the
flow through 90 or 180◦ ; they can be used to change the velocity (usually accelerate) of a
flowing material. The change of direction can be achieved by a series of linear chutes or a
single-curved chute (see Figure 6.4).
The flow of a bulk solids down a chute can be categorised as either ‘slow’ or ‘fast (rapid)’.
The two conditions are illustrated in Figure 6.5 for a simple flat inclined chute. In slow flow
the bulk solid moves at a constant velocity and bed height. This condition occurs for a free-
flowing material where the slope of the chute lies somewhere between the angle of repose
and the angle of internal friction. In fast flow the bulk solids accelerates down the chute
with a decreasing bed depth. If the chute is long enough, a maximum or terminal velocity
may be reached. The chute must be at an angle greater than the angle of internal friction.
Chute surface
Figure 6.2 Schematic of ‘block’ of bulk solid sliding overt a declined chute surface.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:21
(a)
Figure 6.4 Two linear chutes and single-curved chute effecting change in direction.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:21
(b)
Increasing velocity
Constant velocity
Figure 6.5 Slow and fast flow down an inclined flat chute.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:21
Most industrial chutes, linear or curved, are designed for rapid flow. Although a gen-
eral mathematical description of all rapid shear flows would be a difficult or ‘perhaps an
unattainable goal’ (Pudasaini & Hutter 2003) a more accessible analysis for a typical in-
dustrial geometry has been performed by Roberts (2003). Here the motion of the material is
described as a ‘thin stream flow’ where the depth of the flowing bed is always less than the
width of the chute. (A common geometry would have the bed depth less than half the bed
width.) In this case, Roberts uses a lumped parameter model to take account of the frictional
drag at the chute boundaries (wall friction) and internal friction. Roberts has shown that
under these flow conditions, approximately 82% of the energy losses may be attributed to
the bulk solids sliding along the bottom of the chute, 9% due to sliding along the sidewalls
and 9% due to internal friction (Roberts 1969).
The derivation of the model is not reproduced here; however, it is useful to review several
of the equations.
The velocity distribution along the length of a straight inclined chute is given as:
1/2
u = u 20 + 2gs(cos θ − μe sin θ) (6.2)
and for a chute of constant curvature:
1/2
2g R −2μe θ 6μe Rg
u= 1 − 2μe sin θ + 3μe cos θ + e
2
u0 −
2
(6.3)
4μ2e + 1 4μ2e + 1
where μe is an equivalent friction factor and is given by the expression
H
μe = μ 1 + kv (6.4)
B
From continuity of mass at steady flow conditions:
ṁ s = ρb Au (6.5)
is constant and if the variation in bulk density can be taken as negligible:
u0
A = A0 (6.6)
u
Therefore, the variation in stream thickness, H , can be predicted given that the cross-
sectional area of material is expressed as:
B 2 tan λ
A = BH1 + (6.7)
λ
for a rectangular cross-section and
B2 1 − cos δ δ − sin δ
A= tan λ + (6.8)
4 3 2
for a circular cross-section (Woodcock & Mason 1987).
Equations (6.5)–(6.8) can be used either to determine a mass flow rate of solids in an
existing channel or aid the design of a chute for a required solids flow rate.
Material flowing in a curved chute will initially experience acceleration as gravity forces
are larger than the frictional resistance; however, a position at θ is reached where the material
flow may become unstable. It is, therefore, normal to see chutes ‘cut off’ at angles of 45◦ .
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:21
Not all chutes have to be flat or have a constant radius of curvature and many instances,
for example in belt loading, have a parabolic profile.
6.2.1.2 Segregation Segregation from the use of chutes can be generally found from one
of two mechanisms. One mechanism is known as ‘percolation’ or ‘sifting’ where when
the bed of material is in motion with a velocity profile through its depth, smaller particles
can pass through the interstices made by the larger particles (see Figure 6.6). The smaller
particles near the chute surface may alter the friction coefficient and can slow the material
close to the surface resulting in an exaggerated velocity profile (Bates 1997). The bulk then
leaves the chute with a velocity dependent on position and particle size.
The other mechanism, known as ‘trajectory segregation’, occurs if the discharge from
the chute has a horizontal component and is a result of the influence of air drag, which
is a function of particle size, on the particle’s trajectory. This phenomenon can be seen if
transfer chutes are positioned at an angle and the segregation is seen along the cross section
(see Figure 6.7).
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:21
6.2.1.3 Caking The term cake is used here to describe the residue of material which builds
up on chute surfaces, that is, does not self-clear with the passage of more bulk material.
Materials that form the cake are generally the fine particle sizes. Typical mechanisms
are for fines which are initially dry coming into contact with a moist chute surface and
adhering, then subsequent drying results in a hardened cake. Alternatively, wet fines which
migrate to a chute surface, e.g. a sidewall where shear stresses are low and again adhere and
subsequently dry to from a cake. These processes can be cumulative and the cake builds-up
over time until it is either dislodged by the bulk or disrupts the flow. Areas where build-
ups are likely are at any seam or join, at fixing locations and at low shear stress regions.
Therefore, good manufacturing practice must be specified, for example welds must be
ground smooth, no weld spatter etc. Good housekeeping applies, any build-up should be
monitored and the chute cleaned at suitable intervals; the chute should be inspected for
damage.
The application of a vibrating force on the chute (usually bottom) can occasionally be used
to encourage the flow of material and prevent build-up and caking and aid self-cleaning for
transient flows. This is often tried as a retrofit when problems develop. However, care must
be taken as vibration may exacerbate segregation and may cause problems for structures
which were not designed to withstand vibrating loads. The use of flexible materials has
been demonstrated to prevent excessive build up of caked solids. The idea here being that
as the material builds up and gains mass, eventually the flexible section will extend to an
extent that the cake breaks off and is carried away with the normal flow.
Material flow and self-cleaning can also be aided by the application of air to the trough
base to affect the strength of the material. Again this is often a retrofit as a reaction to a
troublesome flow problem.
6.2.1.4 Belt loading Chutes are commonly used in the transfer of material from storage
via a feeder to a belt conveyor. The function of the chute is principally twofold: to direct the
flow of the bulk solid on to the belt without spillage and to accelerate the flow such that the
horizontal velocity matches the belt speed and direction. The design of these chutes must
also minimise the wear of the chute and the belt at the feed point and is the province of the
expert (Wensrich 2003).
Eliciting motion of a bulk material in a trough is not restricted to utilising the effect of gravity
alone and the application of vibration to the trough can provide the necessary motive force.
Rather than using vibration as a flow aid on a gravity chute as discussed previously, the
trough, in its entirety is set in motion. This section will cover the basic theory and the key
features without an overly mathematic treatment.
Unlike the chute which must be set at a relatively large declined angle to ensure that the
bulk will slide against the chute surface, most vibratory conveyors are used for horizontal or
near horizontal conveying with the exception of vibratory elevators which will be discussed
later. They can convey on moderate (about 15◦ ) upward and downward slopes. It is possible
to design in multiple inlets and outlets to the conveyor. The outlets can either be a series of
gates in the trough, or otherwise the stream can be split in some way to provide a number of
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:21
outlets. Multiple inlets are possible simply by feeding at different points along the trough.
It is also a simple matter to cover the trough should the material be particularly dusty, need
protection from the atmosphere, and plastic or stainless steel troughs are available for more
sanitary applications, such as food, pharmaceuticals etc. A typical conveyor geometry is
illustrated in Figure 6.8, showing a flat bed trough mounted on leaf springs with an electro-
mechanical drive. Alternative trough geometries may be enclosed or curved or tubular;
drives of direct mechanical linkage, out of balance motors and coil springs rather than
leaf. Regardless of particularities between devices, common principles and theory can be
usefully applied.
Consider the simplified arrangement shown in Figure 6.9, which illustrates the action of
the vibratory conveyor.
The displacement of the trough ST can be described by the equation:
yT
sT
Product feed Trough
xT
Discharge
Exciter
Guide spring
(leaf type)
Number of
cycles
ft = 1 ft = 2
yT Dynamic material
coefficient
g
Impact of material
on trough
Material lift-
off
yT
1
g
30
20
15
10
0
A B C D E F G H
Test number
Figure 6.11 The effect of changing acceleration on conveying velocity for two materials.
any number of effects due to temperature, ambient gas etc. However, the effect of material-
related properties on transport efficiency can be expressed as a single term Fm , which must
be determined experimentally (very roughly 0.9 for dry granular materials, but is very
dependent on particle size). Other empirical factors allow for various depths of material bed
(Fh with values ranging from 1 at small bed depth to around 0.75 at bed depth of 300 mm)
on the trough and the slope of the trough (Fj with horizontal conveying having a value of
1, incline less than 1 and decline slightly more than 1), resulting in the formula:
u S = ηu Fm Fh Fj λ2π f cos β (6.23)
The mass flow rate or throughput of the conveyor can be estimated by:
ṁ s = ρb Au S (6.24)
where A is the cross-sectional area of the bulk material bed (assumed constant) and ρb the
bulk density.
The effect on flow rate of different materials being conveyed under the same vibrational
conditions is shown in Figure 6.11 and the ability of the methodology to predict flow rates
under different vibration conditions from an empirical knowledge of the relevant factors for
a particular material, alumina in this case, is shown in Figure 6.12.
The direct or positive mechanical drive has a direct mechanical linkage from a drive
motor to the conveyor trough. This type of drive is normally used for longer heavy duty
conveyors. The general arrangement is illustrated in Figure 6.13 with an oscillating motor
connected by a mechanical linkage to the trough, which is mounted on some type of spring
system.
A major problem with the direct drive type arrangement is the transmission of vibration
to the support frame and surroundings. There are two methods of overcoming this problem:
the first is to use a counter-weight that balances the vibration within the trough structure
and isolates it from the support, and the second method is to use a contra-vibrating double
trough where each trough vibrates exactly out of phase with the other.
Typical operating characteristics of this type of drive are for an operating frequency in
the range of 5–15 Hz, a conveying distance of anything between 5 and 30 m, a vibration
amplitude between 3 and 15 mm and an average conveying speed of between 0.2 and 0.8 m/s.
The second type of mechanical drive is the eccentric mass type, as shown in Figure 6.14.
This drive configuration is applied to conveyors and large feeders. The most common
arrangement is to use two contra-rotating masses of equal size. This two-mass system is
able to produce an oscillating linear motion perpendicular to the axes of the motors. This
Figure 6.14 Vibratory conveyors with rotating eccentric mass mechanical drive.
gives some flexibility of control and allows the vibration angle of the system to be altered
to suit the particular product being conveyed. This is particularly useful for feeders, as the
rate can be changed to account for material variations.
The leaf spring design restricts motion to the longitudinal direction and the trough will
move back and forward in this plane under the action of the eccentric masses. A coil spring
mount will result in the motion being simply governed by the direction of oscillation as
defined by the eccentric mass movement.
The typical operating parameters are: operating frequency of around 15 Hz for conveyors
and up to 30 Hz for feeders; distances approximately the same as the direct mode for
conveyors, but slightly less for feeders. Vibration amplitude is variable but is usually in the
range of 1–10 mm, and a conveying speed that is slightly less than the positive drive type.
A final note about this type of drive involves the use of variable frequency controls with
this type of conveyor. These relatively new devices allow control of the conveyor while it is
in operation, and thus can be used to modify the feed rate while material is being conveyed.
6.3.2.1 Electromagnetic drive The third type of drive and the first non-mechanical type is
the electromagnetic drive which is illustrated in Figure 6.15. The basic principle of operation
for this type of drive involves the cyclic energisation of one or more electromagnets, with
at least one attached to the conveying trough. The electromagnets are not in contact, which
has advantages in terms of there being no mechanical fatigue in the design. The operating
frequency does tend to be restricted to twice the electrical supply frequency, which is either
100 or 120 Hz depending on the region of installation. However, it is possible to control this
value down to about 50% by using either a rectifier or thyristor control. The most common
application of this drive type is for short vibratory feeders. The vibration amplitude is
correspondingly low at about 0.1–3 mm and thus so is the speed, which is rarely higher
than 0.3 m/s.
6.3.2.2 Hydraulic drive The final type of drive, and perhaps the least common, is the
hydraulic drive which is typically associated with short heavy duty feeders and is used
mainly in explosion-sensitive environments. The hydraulic drive is ideal for this situation
as a remote pump unit can be used, well away from the hazardous environment and the
hydraulic fluid is supplied to the vibrator at pressure from this remote location. Speed
control of the pump unit allows a variation of the oscillation frequency, and the capacity or
speed can be controlled by the use of pressure control valves on the supply lines.
6.3.3 Mount
The type of mounting system selected depends on three key considerations. The first of these
is the drive mechanism as different drive mechanisms will put different loads on the trough
and these must be considered when selecting a mounting system. The second consideration
is the loading on the trough. This will affect the size of the mounting springs, links, etc. as
well as the type of mounting system chosen. Finally, the transmission of vibration must be
considered.
6.3.3.3 Natural frequency systems Finally are the natural frequency systems. These sys-
tems are designed to resonate at the natural frequency and so a low power input is required to
maintain it in this oscillation. However, a disadvantage of this system is that it is highly load
sensitive due to the fact that the natural frequency of the system is dependent on the total
mass. Therefore, it is only really suitable for applications where either the material mass is
insignificant relative to the trough mass, or the mass in the trough is carefully controlled by
closely monitoring the feed rate. However, it is possible to produce a relatively consistent
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:21
transfer rate from a vibratory feeder with varying load, for example from the feed hopper
head load, by making use of the combined effect of a change in natural frequency and
damping produced by the increased mass of the vibrating system (trough and bulk solid).
When interfacing a hopper to a vibratory feeder care must be taken to allow the bulk solid
to flow freely from the hopper outlet and in such a way as to keep the entire outlet live. This
is done by matching the two geometries as discussed in Chapter 2. A problem seen on plant
is when the skirts which are used to prevent spillage or dust migration are too stiff and have
a severe effect on the trough’s motion and therefore on the transport of solids. It has also
been known for the vibratory conveyor to be directly bolted on to the hopper outlet with
predictably unsatisfactory outcomes.
The vibratory conveyor can also offer possibilities for a simultaneous processing oper-
ation. Typically, wide flat conveyors are used with a mesh or meshes to simultaneously
screen/sort materials and convey to different locations. The large surface area in contact
with the bulk solids also make effective thermal transfer for heating or cooling.
A rather clever variation in a technology developed for near horizontal transport by
forming the trough into a spiral allows the material to be raised vertically within a reasonably
small footprint. The vibratory motion is generally applied via the core support structure and
a total elevation of around 10 m is possible.
Air slides or air-assisted gravity conveyors are mainly used to convey fine low cohesive
materials, such as alumina, cement or pulverised fuel ash, at low angles of declination
(slight inclines are possible with special designs). The principle of operation is to reduce
friction or material strength by the use of interstitial air introduced along the length of the
conveying trough via a porous membrane. The material can then flow at much lower angles
than that of a chute which relies on gravity alone. They are employed for transfer operations
of a few metres and for much longer conveying runs with throughputs anywhere from 10
to 1500 tonnes/h.
The operation of the air slide is highly dependent on the properties of the material being
conveyed and in particular the fluidisation characteristics. To determine the viability of using
an air slide with a material it is useful to look at the Geldart classification methodology
(see Chapter 1). Knowledge of the material’s particle density and particle size enables the
material to be assigned to a particular group based on the location of these parameters on
the Geldart chart shown in Figure 6.16.
If the material falls into Group B then it is likely to be a good candidate for conveying on
an air slide with a low angle of slope and with some materials and appropriate design the
material can be transported at a slight incline. These materials fluidise easily for conveying
and de-aerate quickly when the air supply is halted so giving a good degree of control.
Group D materials will also fluidise but require excessive amounts of air and are therefore
not preferred materials for an air slide. Group A materials will fluidise well with little air;
however, some of these materials may have long de-aeration times and will continue to
have fluid-like behaviour for some period after the air supply has been stopped which may
lead to difficulty in controlling the flow. Group C-like materials have cohesive properties
which make fluidisation difficult and so are generally not suitable for an air slide. However,
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:21
10000
Group B
1000 Group D
Group A
Group C
100
10 100 1000 10 000
Mean particle diameter (micron)
some of these materials may still be capable of transport in an air slide as the air passing
through the plenum, rather than fluidising the relatively impermeable bulk, will form an ‘air
cushion’ which reduces the local friction between the wall and the bulk solid and so aids
flow. The slope of the slide may be higher at around 6–8◦ for this type of material.
The conceptual design of an air slide is fairly simple with a porous membrane sandwiched
between two ‘U’ troughs, as illustrated in Figure 6.17.
Cotton fabric Low cost; light and relatively strong Little rigidity and may require support;
performance adversely affected by the
presence of moisture
Polyester fabric Low cost; light and relatively strong; Little rigidity and may require support
less affected by moisture; higher
temperature range than cotton
Woven steel fabric Relatively expensive
Sintered metal Good for hygienic or high temperature Very expensive
applications; generally gives good
fluidisation; manufactured with a high
degree of uniformity
Sintered plastic Smooth surface and more rigid than More expensive than equivalent woven
woven fabric fabric; not for very high temperature
applications
Ceramic tiles Good fluidisation possible; good for Tiles must be fitted and sealed properly;
high temperatures relatively easily damaged by impacts
The area below the porous membrane forms a plenum chamber and the area above the
membrane, the conveying channel. The membrane can be made from a variety of materials;
a selection of common media is given in Table 6.2 along with advantages and disadvantages.
A major function of the plenum chamber is to ensure an even distribution of fluidising air
across the entire area of the conveying channel base. This is achieved by having a suitable
pressure drop across the porous media such that the pressure drop across the bulk solids is
not significant in determining the superficial air velocity and that the pores of the membrane
are of a size and distribution to ensure reasonable performance and are not easily blocked.
The pressure drop across the membrane should be available from manufacturer’s literature
or a simple test and the expected pressure drop and fluidising air required for the bulk solids
is obtainable from fluidisation tests (see Chapter 1). Limiting the area of the membrane
(and plenum chamber) to mitigate the effects of pressure variation has encouraged the
development of modular units.
The air-assisted gravity conveyor or air slide is generally constructed from modular
components giving a reasonably wide flexibility of design. For example, it is relatively easy
to construct a system with multiple inlets and outlets, to divert oversize material and curve
the chute around corners to deliver to all parts of the plant. Of course, the declination must
be maintained over the length or else the flow will halt.
The principal elements of an air-assisted gravity conveyor are:
r Solids feed – generally a special bolt on unit included by the supplier to interface
between the delivery hopper or feeder and the main body of the conveyor.
r Inspection cover – for the location of blockages and/or monitoring the condition of
the porous membrane.
r Supply of filtered air – the motive air supply at the appropriate pressure and volumetric
flow rate.
r Plenum chamber – a powder-free area for the containment of the motive air.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:21
There are a number of ways to feed an air-assisted gravity conveyor. The most common feed
method is simply a flood feed from a mass flow hopper. A non-mass flow hopper may cause
problems with inconsistent feed which may result in blockages. That is, if too much material
is fed onto the conveyor, then there will be insufficient air to fluidise the material, and if too
little material, or none at all, then conveying may halt due to a maldistribution of air from
the plenum chamber. While an air-assisted gravity conveyor does not work independently
as a feeder, if the bulk solid is metred onto it by the use of a screw feeder or rotary valve, it
will then convey this material at a constant rate. Another method of controlling the flow of
material is to use a gate or baffle at either end of the conveying duct.
6.4.1.1 Slope The optimum value for slope of the channel is dependent on the partic-
ular bulk solid, with free-flowing materials requiring a smaller angle than more cohesive
materials; it is therefore recommended that bench scale tests be completed with the chosen
material. If the angle is less than a critical value there is a possibility that the material will
back up along the channel and eventually cause a blockage. If the angle is larger than the
optimum value there is no gain in performance, and the increase in height may be detri-
mental to the plant design (Woodcock & Mason 1987). It is possible to convey up a slight
incline if the channel is fully choked and the fluidising air also acts as motive air.
6.4.1.2 Conveying distance Conveying distance in most cases should not theoretically
be a limitation on the use of air-assisted gravity conveyors which can be built from a series
of modular units. Headroom may however be a limiting factor. For example, if a conveyor
is 100 m long with a slope of 1◦ , the start of the conveyor would need to be 1.75 m above
the base, and this would increase to 17.4 m for a 10◦ slope required for a cohesive material.
Other operational considerations for long conveyors are, maintaining a uniform air pressure
over the length and venting the fluidising gas to reduce the superficial air velocity in the
space above the conveyed material.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:21
Width = b
Depth = d
The width of the conveyor is usually the main factor in determining its capacity. In the
technical literature for these devices, ‘typical capacity’ (in volume per unit time) is given
as a function of the width of the conveyor (Dynamic Air 2006).
In order to estimate the width required to achieve a desired capacity, knowledge of the
average velocity and the average bulk density of the material is required. The bulk density in
this case is not the aerated bulk density, as there is a further de-rating factor to account for this.
An estimate of channel width can be made from
re ṁ s 1/2
b= (6.25)
ra ρb u s
where operating aspect ratio (ra ) – up to a maximum of about 0.5, this is the ratio of the
depth of material to the width of the conveyor; expansion ratio of conveyed material (re ) –
a de-rating factor for the bulk density of the material that takes into account the aeration
required for fluidised flow; average solids velocity along channel (u s ); mass flow rate (m s ) –
this is usually the target throughput; bulk density (ρb ) – the bulk density of the unfluidised
material (see Figure 6.18).
and troubleshooting that need to be considered. Arguably the most important component
in any air slide is the porous membrane. This must be kept in good order and free from
damage to ensure a reliable performance from the conveyor. The most common problem
with the top side of the membrane is the blinding or blocking of the pores. As pores
become blocked, the distribution of air becomes uneven resulting in flow problems and
eventual stoppages. Correct selection of the porous media to match the conveyed material
will mitigate these problems; however, inspection and monitoring of the pressure in the
plenum can give indications of problems developing. Any problems with the bottom, or
clean air, side tend to be related to unclean air being used. Filtering this air for oil, moisture
and particulates can go along way ensure that a minimum of damage is done to this side
of the membrane. As with all bulk solid plant, blockages are practically inevitable and the
most common method of clearing blockages is to use a rod or other sharp implement which
must be avoided. This is particularly damaging to the delicate construction of the porous
membrane; the woven types can be cut, the ceramic types cracked and even the metal ones
dented out of correct working order.
Bulk materials can be transported in a trough by the action of a moving mechanical com-
ponent acting directly on the bulk solid. An example of this has already been covered in
Chapter 5 on screw conveying where the motive force is provided by a helical flight attached
to a rotating shaft along the axis of the trough. In this chapter, the use of chains with bars
or flights to affect a transport of a bulk material is described.
The first example of this is known as a drag conveyor where an endless chain is dragged
through a trough containing the bulk solid. Variations come with a simple chain with short
flights spaced at a number of links running at relatively high speed to a double chain with
large flat flights attached across the chains at each link which run more slowly. Illustrations of
different chain and flights are shown in Figure 6.19 and the simple assembly in Figure 6.20.
Typical applications for this type of conveyor are in the heavy duty areas of mining or
minerals processing or power generation. Their simple geometry and robust nature make
them ideal for handling materials such as hot cement, clinker and ash or wet mineral ores,
coal and grain. Construction materials may be malleable iron or hardened steel for heavier
duties.
Typical chain speeds are in the region of 0.1–0.6 m/s although there are reported velocities
of up to 1 m/s. These low speeds keep wear rates at acceptable levels even with very abrasive
products. However, this low speed also means that throughputs of solids are limited to around
900 m3 /h. The estimation of mass flow rate of solids for these devices is not simple as it
relies not only on the trough and flight geometry and flight speed (the swept volume) but also
on material properties such as cohesion, wall friction and internal friction, which influence
the slip velocity, the level of fill and the material’s bulk density. The volumetric flow rate of
material may be greater or less than the volume swept out by the moving flight depending
on whether the material slips over the flight or is dragged along with material in contact
with the flight.
The shear zone can be chosen to lie within the bulk which will leave a layer of ‘dead’
material on the trough bottom. This may protect the surface of the trough, however, may
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:21
(a)
(b)
(c)
242
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:21
result in higher forces on the chain and reduced throughput. The simple geometry of
the trough lends itself to relatively straightforward fabrication of wear-resistant linings
needed.
Conveying distances for this type of conveyor are usually less than 100 m and they can
be very noisy in operation. Problems can occur if the material entering the conveyor retains
air and remains fluidised for some time; in this case the throughput may become very low
as the effective slip velocity becomes high. A common problem occurs when large particles
obstruct the movement of the chain or flight, for example by becoming jammed between
the flight and the trough. The inherent flexibility of the chain system can go some way to
mitigate the likelihood of a lump becoming trapped; however, if a jam does occur this puts
high loads on the chain leading to high power demands on the motor or local failure of
the chain. There may be enough capacity in the motor to generate local forces which will
shear a relatively soft lump or fracture a brittle particle. The possibility and likelihood of
this occurring should be considered at the selection stage.
the material will not slide along the trough. In the ideal case the material moves effectively
as a single mass along the trough at a speed approaching that of the chain.
En masse conveyors were originally designed to convey materials in the horizontal plane
only, but the conveying mode has proven to be effective in vertical conveying also, provided
the inlet is kept fed with powder and the trough is enclosed (similar to the action in a flexible
screw conveyor, see Chapter 7).
The flight spacing can also be modified. The usual pattern is to have one set of flights per
chain link; however, if the flights are spaced more widely it has been shown that materials
that are subject to bridging are able to discharge more easily. There are also special flight
designs, such as ‘wiper’ flights (made from, e.g. neoprene) to improve clean-out and oversize
or ‘scavenger’ flights to enable better handling of sticky materials. The flight material is
also key consideration, such as stainless steel for a food-type application, as well as the type
and size of chain that needs to be designed to withstand the conveying load.
Some key considerations in the selection of the overall design of the trough or casing,
see Figure 6.23, are:
r The location and size of the feed and discharge points.
r The requirement for inspection ports or hatches for clearing possible blockages or
tramp material and/or cleaning of the casing.
r The provision of explosion protection for appropriate materials.
r Whether or not a curved section is required, or whether an inclined section would
suffice. When conveying abrasive materials care must be taken to ensure that high
wear areas have been suitably reinforced.
r A special consideration occurs with high temperature products. The high temperature
in the conveyor can lead to creep in the chain material. The effect of this lengthening
is usually overcome by having a casing with an adjustable length, and by having a
controlled amount of sag in the chain designed in.
Because of the wide range of types of conveyor and flight, as well as the different materials
conveyed, previous experience and/or laboratory testing are usually required to determine
the power requirements.
6.6 Summary
The selection of a conveyor should be based on a match of the duty and material properties
to the technology; Table 6.3 gives some broad guidance. Usually, the duty is given; it is
therefore very important to have a good understanding of the bulk material through a deter-
mination of its properties and characteristics. The characterisation methods and accepted
industry standards and practices are discussed in Chapter 1. The key properties of relevance
here are particle size and size distribution, particle density and hardness, bulk density, wall
friction (intended construction materials), internal friction, shear strength and fluidisation
behaviour. Equipment trial should be carried out with the range of materials that will be
conveyed. If the material that is to be conveyed is not yet available, then some simulation
or modelling maybe appropriate. Two simulation approaches growing in popularity and
reliability are those based on either a computational fluid dynamics formulation of the con-
tinuum behaviour of the bulk solid or a discrete element method where individual particles
are modelled (Ma et al. 1993; Theurerkauf et al. 2003).
P1: SFK/RPW
BLUK141-McGlinchey.cls
P2: SFK/RPW
January 2, 2008
Chutes Transfer Large lump to fine powder 1–10 m; declination required Up to few 1000 tonnes/h
T1: SFK
Air slide (air-assisted Transfer/convey Powders (Geldart A/B) Few m to 100 m; near horizontal Up to few 1000 tonnes/h
gravity conveyor) declination;
special design – few degrees
incline
Vibratory conveyors Transfer/convey/feed/ Larger lump (unit mass) to 1–20 m; near horizontal; spiral Few kg/h to few 100 tonnes/h
metre; combined powders – special considerations vertical up (10 m)
process step – screen, for fine/light products;
TROUGH CONVEYING
References
Bates, L. (1997) User Guide to Segregation. British Materials Handling Board, UK.
Ma, D., Eraslan, A.H. & Ahmadi, G. (1993) A computer code for analysing transient three-dimensional rapid
granular flows in complex geometries. Comput. Fluids, 22(1), 25–50.
Pudasaini, S.P. & Hutter, K. (2003) Rapid shear flows of dry granular masses down curved and twisted channels.
J. Fluid Mech., 495, 193–208.
Roberts, A.W. (1969) Trans. ASME J. Eng. Industry, Series B, 91(2), 373.
Roberts, A.W. (2003) Chute performance and design for rapid flow conditions. Chem. Eng. Technol., 26(2),
163–170.
Theurerkauf, J., Dhodapkar, S., Manjunath, K., Jacob, K. & Steinmetz, T. (2003) Applying the discrete element
method in process engineering. Chem. Eng. Technol., 26(2), 157–162.
Wensrich, C.M. (2003) Evolutionary optimisation in chute design. Powder Technol., 138, 118–123.
Woodcock, C.R. & Mason, J.S. (1987) Bulk Solids Handling. Blackie Academic and Professional,
Glasgow, UK.
Nomenclature
Further reading
7.1 Introduction
The area of ‘small operations’ in Bulk Solids Handling is not one to be underestimated.
While a large amount of equipment sales in monetary terms is to the multinational com-
panies and their subsidiaries, there are a large number of companies that are working on
a much smaller scale. Before we discuss these companies any further it is worth defin-
ing the term ‘small operations’. A small operation is one where the majority of the bulk
solids handling is done manually, although there will be some labour-saving devices em-
ployed. The split of manual handling and labour-saving devices will depend on the industry
and the individual company, but in most cases a further bias towards the labour-saving
devices would increase productivity. However, as always, this must be balanced against
the economic costs of this purchase. Some examples of these ‘small operations’ industries
include bakers, glass makers, small quarries, fish feed manufacturers, speciality food and
small tobacco manufacturers. These companies can be further characterised by the size of
equipment they use and the throughput of their plant. For example, a typical flexible screw
conveyor would have a capacity in the range of less than 1 and up to 10 tonnes/h (for an
80 or 114 mm bore conveyor) (Bourton & Clague 2000), whereas a screw conveyor of
150 mm diameter (the smallest offered by some suppliers (Fairport 2006)) is capable of
up to 50 tonnes/h. Taking a further example from pneumatic conveying systems, a power
station may require in excess of 100 tonnes/h of product and for this product to be conveyed
over 1 km (Wypych 1999), a smaller vacuum system typical of these smaller plants may
have a maximum of between 2 and 10 tonnes/h and may convey as short a distance as 4.5 m
(PIAB 2006).
The common characteristic of all these industries, and a definition of bulk solids handling,
is that they all handle powdered or granular materials. The restrictions on the handling of
these materials can sometimes be quite stringent, especially in terms of dust generation and
contamination of the working environment. The handling of heavy loads is also becoming
more tightly regulated, and thus this must also be considered when optimising the handling
of powders in a small operation. This area is covered in some of the relevant UK legis-
lation: Control of Substances Hazardous to Health Regulations 2002 (COSHH), Manual
Handling Operations Regulations 2002, Health and Safety at Work Act 1974 (HASAWA)
and Management of Health and Safety at Work Act 1992 (Risk Assessments) (HSE 2006).
The responsible body in the European Union is the European Agency for Health and Safety
at Work (EU-OSHA 2006), which was launched in 1996. While this agency does not have
its own set of regulations, it does act as an advisory body and a statistical source for the
member states. In the US, the relevant legislation is the Occupational Safety and Health Act
of 1970 (OSH Act), and the regulations come under the Standards 29 CFR. Part 1910 of this
document is entitled ‘Occupational Safety and Health Standards’, where subpart N covers
‘Materials Handling and Storage’ and subpart Z covers ‘Toxic and Hazardous Substances’
250 Bulk Solids Handling: Equipment Selection and Operation Edited by Don McGlinchey
© 2008 Blackwell Publishing Ltd. ISBN: 978-1-405-15825-1
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:22
(OSHA 2006). In Australia, the Australian Safety and Compensation Council (ASCC) is
responsible for the development and oversight of OSH policy. The National Code of Prac-
tice for the Control of Workplace Hazardous Substances (NOHSC:2007 (1994)) and the
Adopted National Exposure Standards for Atmospheric Contaminants in the Occupational
Environment (NOHSC:1003 (1995)) is similar to COSHH, and Manual Handling is covered
under National Standard for Manual Handling (NOHSC:1001 (1990)) and National Code
of Practice for Manual Handling (NOHSC:2005 (1990)).
7.2 Equipment
The equipment that could be used to improve the efficiency of a small operation can be
summarised by the following list, although a number of these items are called different
names by different people:
r Aeromechanical conveyors
r Bag dump stations
r Bulk bag dischargers
r Bulk bag fillers
r Drum dumpers
r Flexible screw conveyors
r Sack fillers
r Small volume batch conveyors
The key advantage of most of these is their portability. A small operator is unlikely to want
to have a number of devices performing the same function and is unlikely to be able to
afford this expense either. Another advantage of all of these is that they reduce the amount
of dust generated by the handling of the powders. They will also generally reduce the
physical load on the plant operator, whether this is by mechanical means, as in the case
of the screw conveyor and the drum dumper, or by pneumatic means for the pneumatic
conveying systems.
Thus for the practical operation of an aeromechanical conveyor, there are a number of
issues that require consideration. The first of these is the size of the discs relative to the pipe
bore. To achieve the turbulence mentioned in Angus’ definition above, the gaps need to be
large enough to create this turbulence, but not so large that excessive amounts of material
can escape through this gap. For the common tube diameters of 75 and 100 mm, a radial
clearance of between 3 and 6 mm is typical. Another key parameter, as can be seen from
Angus’ definition, is the velocity at which the discs are moving. While there is no definitive
method of calculation for this, the range of 2–4 m/s can be used as a rough guide. Another
important practical consideration is the tensioning of the conveyor cable. During operation
there is an inevitable stretching of the cable, so a tensioning device, usually at the discharge
end of the conveyor, is an essential component (Angus 1999).
The mode of operation that makes this conveyor work is not completely understood. In
principle, as the discs are pulled through the tube the powder is pulled along with these
discs. Furthermore, the leakage past the edges of the discs through the clearance gap is
not a significant issue as the next disc will gather up this material and convey it along the
pipe. Indeed, Angus (1999) contends that ‘without slippage, there would be less of the
turbulence and aeration of powder on which the conveyor to a large extent depends’. This
slippage leads the uninformed observer to overestimate the aerodynamic proportion of the
conveying. Despite the advantages caused by the aeration of the material in this type of
conveyor, the mechanical work on the powder is the prime source of conveying motivation.
Another important area for consideration is the interface areas at each end of the conveyor,
that is the loading and discharge points. Starting with the inlet it can be seen that the powder
entering the conveyor must displace the air between the conveying discs in order that it can
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:22
be conveyed along the conveyor. For a simple gravity feed, highly aeratable powders may
cause a problem as they will not settle into the conveyor and this will reduce the capacity. One
possible solution is the use of baffles over the inlet in an attempt to alleviate this problem. The
discharge point has a similar problem. The volume of air in between the discs is necessarily
increased once the powder has been discharged from the conveyor. This additional air
must come through the discharge pipe, which creates a twofold problem. The first is the
same as the inlet where the material must overcome the air resistance of the incoming
air, possibly excessively aerating the material leaving the conveyor; and the second is that
for closed systems, where an inert gas is used, for example, the additional gas must be
supplied.
Typical conveying rate for this type of conveyor is generally given in a volumetric flow
rate, quoted as 15–30 m3 /h in some literature (Entecon UK Ltd 2006; Spiroflow Ltd 2006).
Thus the mass throughput, the convention for most bulk material processes, is dependent
on the bulk density of the material in its conveyed condition. As the material is conveyed in
a fluidised state, care should be taken to obtain a suitable value for this density, especially
as the most common measurements of bulk density are either poured or tapped, which will
give much higher throughputs than the aerated value. Table 7.1 gives indicative volumetric
flow rates for a range of conveyors (Unitrak 2006). Included in the notes for this table are
some de-rating factors for the values that can be used to estimate the mass throughput. The
first of these is a recommendation that the conveyor be run at 50–60% loading by volume.
This is incorporated with the second, a reduction of the bulk density to account for the
aeration, as an overall de-rating factor of 1/4 on the mass throughput, to give the formula
below for a conservative estimate:
Vs × ρb
ṁ s = (7.1)
4
where ṁ s is the mass throughput (kg/min); Vs is the swept volume (L/min); ρb is the poured
bulk density (kg/L).
Although the aeromechanical conveying rates are given as volumetric flow rates, an
aeromechanical conveyor can run at varying volumetric loading percentages, it can indeed
run empty. Therefore, it will generally need a volumetric feeder to ensure a consistent
throughput.
Elsewhere (Entecon UK Ltd 2006), it is recommended that the material be conveyed at
a 20/80 material/air ratio.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:22
Equipment manufacturers (Entecon UK Ltd 2006; Unitrak 2006) quote a wide range
of materials that have been conveyed by aeromechanical means, including food products
such as breakfast cereal, coffee beans and curry powder; metal products such as lead shot
and metal powders; chemical compounds such as aluminium oxide, calcium carbonate
and titanium dioxide; materials for the construction industry such as cement, DIY plaster
type products and tile dust; household goods such as soap granules, talcum powder and
washing powder; plastic pellets and powders; and colouring agents such as carbon black
and pigments.
This method of conveying has a number of other advantages, but is limited to materials
with suitable aeration characteristics. Firstly, the system is an enclosed one, hence is suitable
for dust-free transport. Furthermore, as all the material is travelling at the same speed, it
is reported that there is very little segregation of the material in transport. As mentioned
above, these systems are also available in a portable form. The loading hopper and receiving
sprocket are mounted on a frame with castors mounted underneath (see Figure 7.2).
Although this may be unsuitable for some surfaces, it may be possible to mount more
suitable wheels for uneven and/or soft surfaces. The relatively low energy use of the system
means that the drive motor for the conveying system can be mounted on this frame also,
while the weight of the system is still suitable for manual handling. According to one
equipment supplier (Unitrak 2006) the power consumption to throughput ratio of these
systems is ‘much lower than pneumatic conveying’ and ‘few other systems come close’.
Finally, as the system works with a centrifugal discharge, the dust generation at discharge
is minimised and no filtration system is required for the aeromechanical conveying system
– there may, however, be a requirement for a filtration system on the receiving hopper. The
centrifugal force acts to hold the material in a confined stream until it reaches the discharge
vessel. It is also protected by a discharge tube.
There are additional limitations to this type of system other than being limited to ma-
terials with suitable aeration characteristics. Although this is a relatively gentle method of
conveying material the common material handling problems of degradation and abrasion
are prevalent here. The natural slippage of material between one disc cavity and the next can
result in particles being caught between the discs and the conveyor wall, a possible source
of damage to fragile particles. This natural slippage can also cause abrasion on both the
discs and the wall if the wall and/or disc material is softer than the material being conveyed.
It has been reported that this wear effect is more significant when the conveyor is operating
in a horizontal alignment as compared to conveying vertically (Angus 1999). Moreover,
while the power consumption is relatively low compared to something like a pneumatic
conveying system, this needs to be offset against the increased number of wear parts in an
aeromechanical system; that is, the discs and cable may need replacing over and above the
conveying tube required for both systems.
The materials of construction of the discs, cables and tubes can be varied to suit the
application. However, the discs are usually made of a plastic material, such as polyurethane,
in order to minimise the friction on what are generally steel tubes. Nylon, estane and
polycarbonate are also used for the disc material. The cables are constructed of a steel
wire, usually of a galvanised mild steel or stainless steel dependent on the application. The
conveying tube can also be made of aluminium, which is especially useful for a portable
application due to its lower weight.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:22
hopper, an enclosed system is used to transfer the material to the next step in the process –
another good way of minimising dust generation.
The advantage of mobility means that the station can be moved to wherever the bags
are, rather than the other way around. It is defeating of their purpose to require the bags to
be brought to them, as this then retains a manual handling operation that was trying to be
avoided. However, this may require that the downstream conveying needs to be changed
and this needs be considered when specifying a system. One alternative would be to unload
the bags and transport the material to the required location in the receiving hopper. Care
should be taken in this case to ensure that the material does not consolidate in the hopper.
Indeed, this consolidation may be exacerbated by the vibration caused by moving the stored
material.
A variation on the bag dump station that even further minimises the dust generation and
manual handling requirement is the bag slitter (see Figure 7.4). Bags are placed on a conveyer
belt, thus not requiring support while the bags are opened/emptied, and conveyed into a
dust tight chamber where the slitting blades are situated. Depending on the configuration
the bag slitter can have two or four blades. The blades work with a rotary action, spinning in
the horizontal plane, slitting down the long side of the bag in the two-blade configuration,
having started in the middle of the front edge (see Figure 7.5). The four-blade configuration
is generally used for larger bags and all four sides of the bag are slit simultaneously. Once
the bag is open, it is removed from the system and stored in a waste compaction unit. The
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:22
method of removal varies from a grabbing mechanism to a simple gravity drop. As with the
drum dumper it is possible to fit a dust extraction system that discharges into the receiving
hopper, thus minimising waste.
A labour-saving device that is sometimes used with the bag slitter, and other small
operations equipment, is the vacuum bag lifter (see Figure 7.6). A suction nozzle of a similar
diameter to the width of the bag is connected to a vacuum pump, and when the pump is
activated the force on the bag is sufficient to lift the bag from pallet to feed conveyor, but
not sufficient to break the bag. This greatly assists with manual lifting of awkward loads,
but the necessity of an air supply may be restrictive in some applications.
For lower volume operations, there are also self-contained bag slitters that are of a similar
configuration to the bag dumper (see Figure 7.7). In a way, they are a hybrid of the bag
dumper and the bag slitter. The bags are loaded onto a grill, similar to that found in the bag
dumper, and then a safety hatch is closed over the top prior to the engagement of the cutting
devices. This is generally protected by a safety switch to ensure that there is no danger of
injury to the person loading the device. Once the safety hatch is closed the bag is slit open,
the product discharged into the receiving hopper and the bag removed for storage at the rear
of the device.
An additional option for some types of bag splitter is clean in place (CIP) operation. This
is particularly useful for hazardous powders, and/or processes that use the same bag slitter
for a number of different powders. CIP operation means that it is possible to completely
clean the piece of process equipment without dismantling.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:22
For the bag dumpers the maximum size of the sack that can be emptied is sometimes
dependent on the size of the hopper that receives the material. Other manufacturers specify
a maximum bag size or weight. This varies from manufacturer to manufacturer, so it is
best to confirm these details as required; however, typical maximum hopper volumes are
0.14–0.20 m3 , and maximum bag weights are about 50 kg. For bag slitters the size of the
bag is the more important factor, and this is generally between 1 and 1.2 m. Bag slitters are
capable of handling a range of sack materials, such as paper and plastic, through to Hessian,
jute and/or polywoven (Morray Beltyne 2006; Palamatic Materials Handling 2006).
Before using a particular material in either a bag slitter or a bag dumper it is recommended
to check with the manufacturer as some hoppers may not be suitable. However, some
examples of materials used in these devices are alumina, aluminium sulphate, carbon black,
cement, cocoa beans, cocoa powder, coffee beans, flour, hydrated lime, lime, milk powder,
potassium hydroxide, silica sand, sugars, talc, titanium dioxide and whole nuts (Aptech
(Powder Systems) Ltd 2006; Flexicon Corporation 2006; Palamatic Materials Handling
2006; Spiroflow Ltd 2006; Vibrair 2006).
(a)
(b)
Figure 7.8 (a) Bulk bag discharger with forklift loading (Unitrak Corporation Ltd); (b) bulk bag discharger
with integral hoist (Spiroflow Ltd).
262
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:22
Figure 7.9 Bulk bag discharger with glove box (Spiroflow Ltd).
assistance as the material level reaches the bottom of the bag. To aid in this discharge, the
bag can be raised and the walls at the outlet will become much steeper, closer to or larger
than the mass flow angle for that material.
The bag cutter is used to cut the discharge neck from single use bags. The bag folder
does simply what the name suggests, and is more about keeping the plant safe and tidy than
assisting with the safe and clean discharge of material from the bag. The bag knife is used to
pierce the bottom of single use bags. This is either a static knife for free-flowing materials,
or a pneumatically driven knife that allows greater penetration into materials that may need
assistance to flow from the bag.
A CIP system allows maintenance and cleaning of equipment without significant
disruption to the operation of the process. This type of system is useful for pharmaceu-
tical and food applications that require frequent cleaning. Some of these systems have a
glove box fitted as standard in order that the discharge spout can be handled without any
danger of contact with the stored material (see Figure 7.9).
A cone valve is used at the discharge of some big bag systems. This has the advantage
of dust-free operation, while not affecting the flow of material. Indeed, they can sometimes
act to promote flow without the need for a mechanical or pneumatic stimulation of the
material. As mentioned above, flow activation paddles and bag massaging devices are used
to promote material discharge. This is achieved by effectively changing the local wall angle
by pushing against the bag at a level just above the discharge spout (see Figure 7.10).
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:22
An inert gas purge can be used for powders that are susceptible to explosion. A discussion
of the explosibility of powders is outwith the scope of this Chapter; however, it is worth
noting that the prevention of dust cloud explosions is possible using an inert gas, as the gas
removes the oxygen from the bag and thus combustion is not likely. An integral conveyor
is generally used to transport the discharged material to the next step in the process. The
material discharges from the big bag into a reception hopper, and from here the material
is generally either conveyed using a flexible screw conveyor or a pneumatic conveying
system. To assist with the feeding to a pneumatic conveying system a rotary valve feeder is
occasionally employed. This allows the metering of material into the system, whether it is
positive or negative pressure.
Sack or bag dumping stations have been discussed previously. It is a logical extension
of the bulk bag discharge station to include a hatch for the dumping of sacks. The system
then is a type of hybrid combining the features of the two pieces of equipment. The liner
is exposed to suction, either by opening the valve to the filter or to a vacuum pneumatic
conveying system, in order to completely empty the bag and/or remove any excess dust. As
space is often at a premium in processing plants most of the bulk dischargers come in a low
headroom configuration. There is a minimum height that is physically required due to the
geometry of the situation, but the problem is overcome in a number of different ways. The
first of these is to use a half-height frame that simply consists of the discharge cone and the
receiving hopper mounted on a frame. The bulk bag is then positioned over the top of this
frame using a forklift or similar. Another design is the scissor lift. This is a mobile frame
that allows low headroom operation by compressing down to a small height when not in
operation and opening up for lifting the bag to discharge height. This option is available in
a pneumatically driven type for hazardous environment operation.
When referring to optional materials, this generally refers to the material of construction
of the discharge cone and the receiving hopper. These are available in a number of materials
from food quality stainless steel to mild steel. When selecting for a food application, it is
also important to ensure that the rubber seal materials are also compliant with regulations.
Apart from the mechanical flow aids, some systems are also available with pneumatic
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:22
discharge assistance. The material is aerated by injecting air at the bottom of the bag, and
this assists with discharge of the material. Tramp and oversize material can also be a hazard
when discharging bulk bags. To avoid these objects moving further through the process a
screen between the bag and the receiving hopper is occasionally employed. For hazardous
applications such as for pharmaceuticals it is usual to use a sealed system. In addition to
being a completely enclosed system, these systems employ a liner on the discharging cone
that is disposed of after use. In this way the FIBC is left uncontaminated and is available
for re-use.
Occasionally, it is necessary to stop emptying a big bag at some point during the process.
The two main methods of achieving this are the spout clasping clip and the iris valve. The
spout clasping clip appears to be a relatively new development that works with a scissoring
action to clamp the discharge spout and stop material flow. It would appear to allow quicker
and easier clasping of the bag than the conventional iris valve. The reason for this may be the
fact that the iris valve requires the rotation of one flange, whereas the spout clasping clip is
a separate device that operates externally to the flow pipe. Vibration discharge aids are also
attached to bulk bag dischargers. It has been shown that for some powders the application of
a small vibratory load can promote flow. However, care must be taken to specify this system
correctly, as an incorrect application can result in consolidation of the material, exactly the
reverse of what is trying to be achieved. The final attachment that is occasionally attached
to a big bag discharger is a load cell arrangement. Generally the big bag is hung from a
cantilevered beam and a loss in weight system is used to achieve weigh-batching from the
subsequent conveying system.
The application of bulk bag dischargers is wide and varied. A large number of different
products have been successfully discharged using these systems, but as with all bulk solids
plant, a knowledge of the flowability of the material is essential before specifying a sys-
tem including this equipment. Some typical materials handled are breakfast cereals, car-
bon powder, chemical dyes, ceramic powders, cut potatoes, dried fruits, flour, limestone,
pharmaceutical powders, plastic pellets, plastic powders, rubber crumb, sand, soap flakes,
soda ash, sugar and yeast powder. Some typical applications of a bulk bag discharge sys-
tem are to feed into a flexible screw conveyor or aeromechanical conveyor for transport
further down the process: straight into a mixer, with the possibility of using a loss-in-
weight system to assist with batch blending; and a particular application of three dis-
chargers in series used to supply the three components of layered detergent tablets (Aptech
(Powder Systems) Ltd 2006; Dynamic Air Conveying Systems 2006; Entecon UK Ltd 2006;
Flexicon Corporation 2006; Flomat Bagfilla International 2006; Hosokawa Containment
2006; Spiroflow Ltd 2006; Vibrair 2006).
(a)
Figure 7.11 Static bulk bag filler: (a) two post type (Flexicon Corporation); (b) four post type (Spiroflow
Ltd).
supporting poles. The loading chute is mounted above the bag and material is loaded into the
bag by means of either a flexible screw conveyor or a pneumatic conveying system. Some
configurations make use of an intermediate hopper for storage of the material. This can
be useful for pneumatically fed systems where a large amount of air needs to be removed
before filling the bag.
The bag can be attached to a frame that has forklift blade slots included for easy
manipulation of the bag once full. To aid with bag filling it is also possible to have load cells
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:22
(b)
attached to this frame that allows accurate filling based on weight. This is particularly useful
for easily aeratable powders that may require settling to ensure that the target weight capac-
ity of the bag is achieved. Accelerated de-aeration can be achieved with some materials by
mounting a vibratory system to this frame. As always, care should be taken to specify and
commission this system correctly, as incorrect application of the vibration force may only
serve to exacerbate the problem. Some systems include an automated controller to achieve
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:22
this outcome. These systems can also be mounted on casters to allow portability of the
system around the site. Furthermore, for sites with a height restriction, a low profile design
is available that also comes with pallet truck access – removing the need for a forklift.
The more sophisticated configurations discussed next allow a degree of process
automation, and allow a faster throughput of bags while still maintaining a dust-free loading
process. The first of these is the static frame type that is mounted above a belt roller upon
which pallets are placed to support the bags prior to and after filling. This design allows an
almost continuous filling process to be achieved while maintaining all of the features men-
tioned for the static loading device mentioned above. Unlike the static filling arrangement,
however, the weighing of the bag is achieved by load cells mounted underneath the pallet
supporting the bag. There are a number of different design configurations within this sub-
set. The cantilevered design generally allows for a variety of bag sizes through an adjustable
height feature (see Figure 7.13); however, for larger bags the attachment of the bag can be
at an uncomfortable height. The adjustable height feature can be either powered or manual.
The problem of attachment of bags at an awkward height is overcome to a certain extent,
although at the cost of slightly reduced throughput, by the use of a lowering and pivoting
fill head. By lowering the fill head and pivoting it at a 90˚ angle, it is much easier to attach
the top of the bag to the filling chute. The fill head is returned to its vertical position for
filling (see Figure 7.14).
Another type consists of a two post arrangement where the bags pass under the filling
device supported on top (see Figure 7.15). For applications that require an extremely high
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:22
throughput, up to 80 bags per hour, a carousel design could be applied (see Figure 7.16).
The bags are attached to a rotating device that allows a bag to be filled while subsequent
bags are attached to the carousel. This system uses hang weighing to determine degree of
bag filling and features automatic bag removal. However, bags still need to be manually
fitted to the carousel.
As with all of the equipment we have discussed so far, these are all available in a wide
range of materials. While the frames are generally constructed from a mild steel, as they
do not come into contact with the process material, a wider range of materials are available
for the loading chute. These can range from high quality stainless steels for food and
pharmaceutical applications to lower grade mild steels for less arduous duties. The static
frame noted above can be used in applications where frequent wash downs are required for
sanitary purposes.
For operations that use a variety of storage containers there are designs that are adaptable
to this application. This is achieved by fitting an adapter to the filling chute used to fill the
IBCs. Another option that is available for all of the configurations mentioned above is the
pre-inflation of the bag prior to filling. This allows the material to flow freely into the bag
without any physical obstructions. However, it is important that the material be de-aerated
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:22
Figure 7.14 Pivoting fill head bulk bag filler (Flexicon Corporation).
upon completion of filling (see above). For materials that require an inert atmosphere,
some systems can be fitted with an inert gas purge. A slightly different method of loading
IBCs comes in the form of a cone valve (see Figure 7.17). There are a number of different
arrangements available that offer increasing degrees of dust containment (ISL Cone Valve
Technology 2006; Matcon 2006). The simplest design consists of a single valve, while other
designs include an integral lower cone and others consist of a fully automated system where
the valves and the containment lids do not require any user intervention.
While the integrated systems above have the advantage of being supplied in a complete
package, it is not impossible to fabricate a system from scratch, even to the point of attaching
a weighing system. While not such an advantage for some of the automated systems, an
application such as the static system described initially would be suitable for this option.
There are a number of instrumentation suppliers that are capable of providing the load cells
required for the weighing system, and they may even be able to supply the associated control
system required for batch filling.
As with the bulk bag dischargers, the materials used in, and the application of, bulk bag
fillers is wide and varied. However, the same proviso holds; care must be taken to ensure
that the system is adequately designed to take into account the flowability characteristics
of the material. Some example materials and applications are the loading of polymer resins
into a variety of container sizes; the batch weighing of PET; the filling of bags in a carousel
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:22
system with polypropylene and polyethylene pellets. The following materials have also been
successfully used in these systems: aggregates, detergents, fertiliser, flour, grains, plastic
pellets, salt, skimmed milk powder, sugar, urea and yeast (Arodo Total Bag Handling 2006;
Flexicon Corporation 2006; Flomat Bagfilla International 2006; Hosokawa Containment
2006; Matcon 2006; Spiroflow Ltd 2006; Webster Griffin Ltd 2006).
(a)
(b)
Figure 7.18 (a) Chute type drum dumper; (b) clamped cone type drum dumper (both Flexicon Corporation).
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:22
contained within the transfer section. This receiving hopper can also be fitted with either a
flexible screw conveyor or a pneumatic conveying system.
Another design with a clamped cone involves lifting the drum above hopper height and
then rotating through 180˚. The discharge cone is then aligned with the inlet to the hopper and
the material discharged through these aligned pipe sections. As with all process equipment,
it is important that the cone of the dumper is designed such that the material will not
‘hang-up’ in this section. With the small quantities of material being discharged it is unlikely
that a mass flow design will be required; however, the slope needs to be adequate to ensure
that the cone is self-cleaning. These devices are available in either carbon steel or stainless
steel for operations requiring a hygienic surface. Importantly, for the small operation both
variations of design have an aspect of portability. Some designs are fitted with casters,
whereas others have a sack trolley like design that allows the drum and tipping device to be
moved around the site. All of the designs are manually operated.
A variation on this type of device is a drum rotator. The device works on the same principle,
and can be electrically or manually operated, but requires a separate hopper and/or delivery
chute (S.T.S. Safety Trolley Systems 2006).
of the conveying tube, the material can be delivered through a flexible routing. This same
advantage is enjoyed by a pneumatic conveying system, but screw conveyors are much more
suitable for routes of less than 10 m and can also convey at any angle. Another advantage
of a flexible screw conveyor is that the screw itself is the only moving part. There are no
internal bearings, and the material is fed directly into the screw from the feed hopper. The
screw, constructed from a spring steel or stainless steel, is of the ribbon type; that is, it has
no shaft.
There are a number of materials that a flexible screw conveyor is capable of conveying.
Bourton and Clague (2000) list 141 materials, including food products such as frozen
blueberries and rice flour and hulls, minerals and sands such as alumina and limestone,
chemical powders such as ammonium chloride and potassium bicarbonate, plastic powders
such as PVC and acrylic powders, rubber products and sticky materials such as china
clay and gelatine. Fitzpatrick (1985) lists 85 materials divided into three areas: chemical–
pharmaceutical, foods and plastics. Examples in the chemical–pharmaceutical area are
soda ash, aspirin granulation and acetylsalicylic acid; in the foods area are powdered sugar,
instant coffee and sesame seed; and in the plastics area are pellets, colour concentrates
and polyethylene powder. Despite this versatility, care should be taken to ensure that the
properties of the material are taken fully into account before attempting to convey the
material. The following list gives an indication of some of the key material considerations:
r Bulk density (packed, loose and average)
r Particle size
r Particle shape
r Angle of repose (flowability)
r Temperature
r Moisture content
r Fat/oil content
r Abrasive/corrosive
r Degradable (affecting process/final product)
r Compressible/rubbery
r Aerates/fluidises
r Solidifies (if left to sit or vibrate) agglomerates
r Packs, cakes or smears under pressure
r Bridges when hoppered (or ratholes)
r Mechanically interlocks
r Hygroscopic
r Hazardous
The majority of these items would be covered by a standard material characterisation
exercise (for more details see Chapter 1); however, it is worth discussing here how each
of the criteria affects the conveying performance. The bulk density of the material is used
to approximate the throughput of the conveyor. That is, while the volumetric throughout is
reasonably consistent, most processes rely upon a mass throughput and thus the ‘conveyed’
bulk density is required. While a precise value of mass throughput is not usually possible,
due to the nature of the conveying process, the loose bulk density normally gives a good
estimate. A typical range of bulk densities that can be conveyed is 100–3000 kg/m3 . The
particle size and shape determine both the size of the conveyor tube and the clearance
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:22
Table 7.2 Maximum particle size for various tube sizes (Bourton & Clague
2000).
between the screw and the tube. While tube size is not critical for particle sizes below, say,
1 mm, once the particle size is a significant percentage of the tube diameter, care should be
taken to ensure that the material will not jam the screw. For example, a typical size of the tube
is normally in the range of 50–220 mm and the maximum particle size is approximately 25
mm. It is clearly not practical to convey this largest particle in the smallest tube size. Indeed,
Fitzpatrick (1985) gives a maximum particle size of 1/4 (6.35 mm), but as no tube diameter
is given to relate this too, this figure may be misleading. For particles where degradation
and/or abrasion are an issue, the particle size and shape are used to determine an appropriate
screw/tube clearance. Particle size is critical as it should be ensured that it is not possible
for a particle to be trapped between the screw and the tube, and particle shape is critical as
particle size is usually some average value and non-spherical shapes may result in jamming
when the mean size is less than the gap. Table 7.2 gives indicative maximum particle sizes
based upon the diameter of the outer tube.
The flowability of the bulk material is also important. While Bourton and Clague (2000)
associate only angle of repose with flowability, several of the other criteria listed above could
also be grouped under flowability – compressible/rubbery; aerates/fluidises; solidifies (if
left to sit or vibrate) agglomerates; packs, cakes or smears under pressure; bridges when
hoppered (or ratholed); and, mechanically interlocks. So, while the angle of repose is
important in determining the angle of the screw flights, many other aspects of the material’s
flowability should be assessed when considering the design of the flexible screw conveyor.
Temperature, moisture, abrasion and corrosion are other important material characteristics
in the specification of a flexible screw conveyor.
The influence of particle size on degradation has been discussed, but screw speed should
also be selected to minimise the damage caused. The two final criteria, hygroscopic and
hazardous affect the environment in which the material is conveyed. Both require that the
system be as closed as possible, in order that for the hygroscopic material, excess moisture
is not allowed to ingress, and for the hazardous material, no material is allowed to escape
to the atmosphere. The importance of a number of the selection criteria outlined above is
minimised by the fact that the screw is self-centring. There are two forces applied upon the
conveyed material within the screw area: an axial force that acts to convey the material along
the tube and a radial force that presses the material against the conveyor tube. This radial
force provides a barrier between the tube and the screw. Thus, providing the tube is not
excessively curved, the screw will remain in the centre of the tube (Bourton & Clague 2000).
This is the phenomenon that allows flexible screws to be ‘self-centring’. Some designs also
have CIP capability. This is made possible by the fact that the screw is the only moving part,
and further assisted by the fitting of an end cap that allows direct access to the screw inlet.
The feed section of the screw is generally sited in a U-shaped trough, situated directly
below the feed hopper. This section of the screw picks up and feeds the material into the
tubular section of the screw conveyor and the material is conveyed to the outlet point.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:22
The motor drive for the screw is generally mounted on the discharge chute. This not only
means it is away from the ‘dirtier’ feed end, but it will generally be well isolated from the
material itself, which has obvious operating advantages in terms of dust protection, etc. The
discharge chute simply provides a gravity fed slide for the material to be directed away from
the screw conveyor body and into the receiving hopper. For extended routes or elevations,
it is possible to connect the discharge chute to the inlet of a subsequent conveyor.
While the tube is generally made of a flexible plastic material, it can also be constructed
of a rigid plastic or steel. These designs retain the advantages of the ribbon screw while
providing a rigid conveying route where the flexible plastic is not necessarily required.
Another advantage of the plastic tube material is that the weight of the overall assembly
is reduced over a rigid steel screw conveyor. This lends the assembly to adaptation for
a portable unit. Fitzpatrick (1985) gives two additional advantages of using polyethylene
tubes: (i) the slick, smooth surface greatly assists with cleaning, that assists with batch
integrity and multiple use; (ii) the surface is also largely resistant to chemical attack from
most materials. The feed hopper is either mounted on a frame with casters, with the screw
conveyor attached to the hopper, or the screw conveyor can be supported separately if
necessary. This portability is further enhanced by the ability to use interchangeable screws.
Thus, if the one screw conveyor is required to satisfy a number of duties on the one site,
the only component that needs to be changed to handle the different material is the screw
itself. Indeed, it may even be possible to convey different materials with the same conveyor
and screw if the materials are suitably similar and/or the throughput rate is not critical.
Looking at the screw in more detail we find that for the majority of applications a circular
cross section is suitable (see Figure 7.20). This design is used for two main reasons; a large
number of materials can be conveyed using this design, and it also produces a greater radial
force, thus providing a more resilient bearing face of conveyed material between the screw
and the tube. A heavier gauge of screw material may be used for heavy bulk materials
(bulk density >1500 kg/m3 ). While this design is suitable for free-flowing powders and
granular materials such as sugar, flour, soda ash, plastic powder, plastic pellets, rice, corn,
regrind, etc. (Bourton & Clague 2000), a flat profile of one of two types is used for more
difficult powders. For powders that aerate/fluidise easily a flat profile screw is used, as this
provides a greater ratio of axial force to radial force compared to the circular profile. For
the same size screw this design will give a higher conveying capacity than the circular cross
section. This assertion is confirmed in Fitzpatrick (1985). For materials with particularly
poor handlability, a tight toleranced flat screw and tube are required to minimise the radial
force exerted. This results in the maximum forward motion of material for input power, and
minimises the impact with the wall for materials that suffer from degradation and/or caking
or packing if overloaded. Figure 7.21 demonstrates the different conveying characteristics
of the three different screw profiles.
However, the division between the two types of cross section is not clear cut, and
comprehensive testing of different screw configurations is recommended. Furthermore,
the screw cross section is not the only variable that needs to be considered. The conveyor
tube must be large enough for the desired throughput, with the screw diameter some sig-
nificant percentage of this value, and the screw pitch must also be specified accordingly.
More details on the specification of screw conveyors can be found in Chapter 5. However,
due to the specialised nature of these screws with the flexible screw routing and changes in
elevation, these figures will most likely only provide a design estimate.
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:22
Typical maximum lengths for flexible screw conveyors range from 4.5 to 12 m dependent
on the conveyor diameter and the duty required from the conveyor. The maximum length
tends to decrease with increasing conveyor diameter and increasing level of duty, where the
duty of the conveyor is considered more strenuous with increasing elevation and material
bulk density. Another key characteristic for flexible screw conveyor specification is the
minimum required bend radius to avoid fouling of the screw on the conveyor tube. The
three variables to be considered in this situation are the conveyor size, the degree of bend
Vertical arrows
represent magnitude
of conveying force
Vertical lines
represent radial
force exerted
(a) Round wire (b) Flat wire (c) Machined wire
Figure 7.21 Comparative loading of screw cross section types. (Adapted from Bourton and Clague 2000.)
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:22
and the type of screw, whether it is flat or round. This minimum radius that ranges from 1.5
to 6 m tends to increase with increasing conveyor size and degree of bend. Furthermore,
flat screws require a larger minimum bend radius than do round ones.
The capacity of the flexible screw conveyor, typically given as a volumetric flow rate,
ranges from as low as 0.12 m3 /h to 40.0 m3 /h. It can be seen from Figure 7.20 that for the same
size screw a flat or machined profile screw will have a greater capacity than a round screw,
and from simple geometry a larger screw diameter corresponds to a larger capacity. For
example, a typical maximum with a 67 mm diameter conveyor is approximately 1 m3 /h and
to achieve the 40 m3 /h capacity a 220 mm diameter screw would be required. The volumetric
throughput is also dependent on the rotational speed of the screw, with approximately double
the capacity for a doubling in screw speed – however, this relationship becomes less and
less reliable with increasing screw size.
Figure 7.22 Typical sack filling devices (A.T. Sack Fillers Ltd).
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:22
maximum particle size and the conveying length are all within the constraints required for
the use of Equation (7.2).
Once the conveyor has been chosen, it is necessary to choose the conveying line diameter
that will be used to convey the material from the loading hopper to the vacuum receiver.
The selection of pipe diameter is based upon the conveyor model chosen and the material’s
bulk density. Typical pipe diameters are in the range of 32–102 mm, and generally lighter
products require a larger pipe dimension. This is due to the fact that the velocity of the
conveyed product will be the same for each conveyor selected from the previous process,
so to achieve a greater mass throughput a greater cross-sectional area is required. Once
again it is worth stating that these figures are recommendations and should be confirmed
by product testing.
Therefore, for the three conveyors selected in the previous step, the pipeline diameters
are 76 mm or 102 mm (PIAB 2006).
The customised selection process takes the customer through the individual units that go
to make up a complete conveyor (PIAB 2006):
r Pump unit – the part of the conveyor that allows the whole to meet the capacity and
conveying distance, as shown in the first part of the standard selection process.
r Filter unit – dependent on the type of material and its bulk characteristics.
r Connection unit – the connection between the receiving vessel and the pipeline, this
is also dependent on the material characteristics.
r Bottom valve unit – available in a number of materials, and with or without fluidisation,
the application and material characteristics decide the selection of this item.
r Control unit – connected to both the pump and the bottom valve, this unit ‘runs’ the
conveying system.
r Nylon tubing unit – provides the connection between the control unit, pump and
bottom valve, including fluidisation ports, if required.
Another supplier of this equipment is K-Tron (2006), where the main application appears
to be the use of this type of equipment as a loading/re-filling mechanism for a range
of feeders. Thus, the selection guide is geared more in this direction. K-Tron use three
selection parameters: material type, material flow and conveying capability (conveying rate
and distance); and as with the PIAB equipment, the selection process is only given as
a guide, and it is recommended that the material to be conveyed is tested either by the
equipment supplier or independently to assess its conveying characteristic. Material type
is divided into ranges of particle size, and also takes into account particle shape. However,
this appears slightly redundant as the selection table infers that any of their conveying
systems are capable of handling any of the different shaped products. Furthermore, the only
apparent consideration for the finer powders is to use a conveying system with an in-built
filter. The material flow section is divided into five flow regimes: very free flowing; free
flowing; average flowing; sluggish flowing; and non-free flowing. No further information
is given regarding these sub-divisions, but there are a number of different methods where a
similar characterisation can be achieved, such as Carr’s compressibility index or the angle of
repose (see Chapter 1 and McGlinchey 2005). Conveying rate is divided into four sections,
up to 500 kg/h, up to 1000 kg/h, up to 2500 kg/h and up to 5000 kg/h. To achieve a short
(5 m), medium (5–25 m) or long (>25 m) conveying distance, different conveyors are then
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:22
specified for each conveying rate. This information can then be used to select a conveyor
configuration for the flour application given above (K-Tron 2006).
Apart from the feeder application mentioned above another application of small volume
batch pneumatic conveyors is for a receiving vessel above a mixer inlet (Burgess 2006). The
vacuum receiver vessel is mounted on load cells, and the control unit is set up to convey
each of the ingredients into the receiving vessel. Once all the ingredients have been loaded
and the mixer is emptied from the previous cycle, the vacuum receiver can be emptied into
the mixer and while the mixing is taking place, the next load can be conveyed. This has the
advantage of reduced down-time for the mixer as it is not waiting for material to be loaded
whilst not in mixing mode. Two other applications noted by Burgess (2006) are a check
screen and a metal separation screen. Because of their wide use in the food industry (being
good for small batch weighing and with a sanitary finish such as 316 stainless steel) both of
these applications are quite important. Occasionally, the bag slitters that have been discussed
previously in this section can leave scrap pieces of bag in the process material. A check
screen mounted in the vacuum conveying line can help reduce the amount of this ‘tramp’
material, with the air passing through only serving to increase the collecting efficiency. Metal
separation is achieved by mounting a ‘bullet’ magnet in-line in the vacuum conveying line.
A design advantage of the ‘bullet’ magnet is that it minimises the obstruction to flow and
with sufficient air velocity no residual product remains attached to it, thus reducing the
hygiene risk. Metal pieces attached to the magnet are cleaned from the ‘bullet’ by access
through a trap door.
For shorter distance conveying, remembering that vacuum systems are generally limited
to a maximum of 0.5 bar gauge line pressure drop, it is also possible to convey materials in
a low velocity dense phase mode (Burgess 2006). Some examples of products conveyed in
this mode are roasted coffee beans, puffed rice, oats, spray dried milk powder, peanuts and
breadcrumbs. Whole almonds were conveyed along a 65 mm flexible tube at a rate of 1500
kg/h into a hopper in another application (Walker 1994). Indeed, the range of materials
that can be conveyed in a vacuum conveying system stretch well beyond these examples
given for the food industry. Examples of other industry sectors where this technology is
applied are plastics and rubber, e.g. polyester pellets, polythene powder, rubber granules;
chemicals/detergents, e.g. aluminium oxide, detergents, soap flakes, magnesium oxide,
titanium dioxide; and pharmaceuticals, e.g. penicillin powder (Jenco Engineered Solutions
2006).
7.3 Summary
This section has provided an introduction to the equipment that is available to smaller
operators in order to make their operations more efficient. While one piece of equipment
may provide some benefits, it may be necessary to consider the combination of a number
of pieces of equipment as described above. It is recommended that some knowledge of
characterisation be obtained to assist with the use of all this equipment. Labour-saving
equipment is not going to be of use if it has not been correctly specified for the bulk solid
it is handling. There are also a number of good references on the subject of particle and
bulk solid characterisation for those who wish further information in this area (McGlinchey
2005; Woodcock & Mason 1987).
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 2, 2008 21:22
References
Index
abrasive materials 150, 166, 169, 174, Carr’s compressibility 14, 29, 283
187, 194, 206, 245 Carr’s indices 10, 22
aerated density 7, 13 catastrophic failures 128
aeromechanical conveyors 251 CEMA 202, 205
aggregates 221, 272 cement 99, 136, 141, 169, 173, 184, 236,
agriculture 136, 221 241, 254, 260, 444, 466
air-assisted gravity conveyors 236 chemical composition 94, 113
air movers 141, 159 chemicals 136, 162, 198, 221, 254, 272,
air only pressure drop 181, 183, 315 275, 277, 284
alumina 28, 122, 136, 232, 236, 260, 275 chute design 221
angle of friction 28, 73, 75, 199, 210 CIP (clean in place) 259, 263, 276
angle of repose 17, 22, 27, 29, 30, 60, coal 54, 68, 92, 170, 241
120, 126, 283 coating 92
arches 15, 69 cohesion 22, 27, 30, 37, 41, 53, 54, 59
arching 74 cohesive strength 37, 41, 44, 53, 74, 94,
ASCC 251 100
aspect ratio 102, 129, 240 compression ratio 161
attrition (see degradation) 69, 86, 97, concrete (silo) 129
113 conveying air velocity 136, 142, 160,
171, 177, 179, 182
bag slitter 257 conveying distance 140, 171, 174, 183,
batch conveying 136, 141, 158, 279 186, 233, 239, 243
bed depth 222, 232 conveying line inlet air velocity 180, 186
belt loading 225, 228 conveying line pressure drop 171, 173,
bends 165, 176 175, 180, 183, 186
blow tank 141, 154, 254–9, 281–2 Conveyor Equipment Manufacturers
blowers 161 Association (CEMA) 202
bridging 74 core flow 132
brittle materials 193 corrosion 92, 97, 130
buckling 128 COSHH 250
bulk (big) bag 260, 279 cracking 121, 129
bulk density 4–5, 7–11, 15, 17, 24, 30, cross-contamination 97
43, 55, 75, 80, 103, 151, 190, 206, 219, cyclone separator 157
225, 230, 240, 241, 245, 253, 277, 282
bunker 68 degradation 69, 85, 135, 146, 174, 195,
butterfly valves 93, 169 245, 254, 276, 277
delivery pressure 163
cable and disc conveyors 251 dense phase 136, 172
caking 59, 85, 95, 228, 277 dilute phase 136, 160, 172
Bulk Solids Handling: Equipment Selection and Operation Edited by Don McGlinchey 287
© 2008 Blackwell Publishing Ltd. ISBN: 978-1-405-15825-1
P1: SFK/RPW P2: SFK/RPW QC: SFK/RPW T1: SFK
BLUK141-McGlinchey.cls January 24, 2008 3:7
288 INDEX
INDEX 289
290 INDEX
temperature 31, 53, 73, 93, 94, 146, 159, vacuum systems 135, 138, 242, 243,
162, 238, 245 275, 284
tensile strength 22, 37, 54, 115, 118, venting 93, 138, 139, 239
119, 122, 129 volumetric flow rate 163, 179, 240, 253,
thermal power 218 279
thin shell structures 125
throw factor 230 wall friction 25, 30, 37, 47, 73, 80, 92,
time of storage at rest 73, 94 104, 113, 114, 121, 206, 210, 225, 231,
titanium dioxide 45, 102, 104, 253, 260, 241
284 wall pressures 104, 112, 115
ToteR
68 Warren Springs Laboratory 42
toxic (materials) 135, 157 wear 69, 86, 92, 97, 135, 150, 154, 167,
transition hopper 88 174, 188, 193, 202, 206, 213, 221, 226,
241, 245, 254
unconfined stress 12, 35, 45 wedge-shaped hopper 75, 88
uniaxial compression 44 weighing 97, 219, 267, 268, 284
unsymmetrical pressures 112, 121, 127,
129 yield loci (locus) 25, 30, 35, 41, 57