Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 315 views

    CARPROG Motorola HC08 Programmer Manual

    Uploaded by

    cameraman01
    This document provides instructions for programming Motorola HC08 microprocessors using the CarProg programmer. It describes the necessary cable, how to identify the microprocessor by its maskset, how to connect the programmer, potential error messages, and troubleshooting steps to check if the correct microprocessor type and signals are selected.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd

    CARPROG Motorola HC08 Programmer Manual

    Uploaded by

    cameraman01
    315 views8 pages
    This document provides instructions for programming Motorola HC08 microprocessors using the CarProg programmer. It describes the necessary cable, how to identify the microprocessor by its maskset, how to connect the programmer, potential error messages, and troubleshooting steps to check if the correct microprocessor type and signals are selected.

    Original Description:

    m

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides instructions for programming Motorola HC08 microprocessors using the CarProg programmer. It describes the necessary cable, how to identify the microprocessor by its maskset, how to connect the programmer, potential error messages, and troubleshooting steps to check if the correct microprocessor type and signals are selected.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    315 views8 pages

    CARPROG Motorola HC08 Programmer Manual

    Uploaded by

    cameraman01
    This document provides instructions for programming Motorola HC08 microprocessors using the CarProg programmer. It describes the necessary cable, how to identify the microprocessor by its maskset, how to connect the programmer, potential error messages, and troubleshooting steps to check if the correct microprocessor type and signals are selected.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 8

    S4.

    4 CarProg Motorola HC08 Programmer manual

    For Motorola MPU MC68HC08 series programming use A10 cable.

    You can recognize Motorola (Freescale) MPU by maskset:

    This MPU maskset is 4C11W. First digit 4 is mask series number, in practice can be 0, 1, 2, 3, 4 or 5, but for programming is not important.

    All right reserved www.codecard.lt

    Second 4 symbols is always letter + digit + digit + letter: this is processor maskset or encrypted processor type. All processor marking can by custom made, like FORD S2234234 or SC2323454 but always you can find maskset on Motorola or Freescale processors.

    Before programming always select right processor type according maskset.

    How to connect CarProg programmer: For HC08 programming use A10 cable 6 color wires: BLUE Reset signal to MPU; ORANGE PTC0 signal to MPU, must by high level; BROWN GND (ground); GREY PTA0 communication signal; WHITE IRQ +8-10V signal in most cases you must pull-up this processor pin; RED switched +5V; VIOLET - switched +12V;

    All right reserved www.codecard.lt

    Troubleshooting: CarProg ERROR messages: Communication error - no communication between CarProg and Motorola processor check MPU type, try to select quartz frequency manually.

    All right reserved www.codecard.lt

    To understand better onboard MPU programming problems, you can use table with right programming signals and voltages, described in table. If you cant read or write MPU with CarProg, check: did you was select right MPU type; did quartz resonator Q is the same in circuit board and in CarProg options; did all programming signals have right form and voltage;

    Grey PTA0

    Blue RESET

    Orange PTC0

    White IRQ

    All HC08 MPU

    Impulse 3.3-5V

    Reset

    Must by HIGHT

    +9-10 V

    If all conditions are OK and still no connection ask support@codecard.lt

    All right reserved www.codecard.lt

    1. MC68HC908AS20, MC68HC908AS32

    All right reserved www.codecard.lt

    All right reserved www.codecard.lt

    1. MC68HC908AZ0, MC68HC908AZ16, MC68HC908AZ32, MC68HC908AZ60, MC68HC908AZ60A, MC68HC908AB32, MC68HC908AB60

    All right reserved www.codecard.lt

    All right reserved www.codecard.lt

    You might also like