L297

L297D
STEPPER MOTOR CONTROLLERS
NORMAL/WAWE DRIVE
HALF/FULL STEP MODES
CLOCKWISE/ANTICLOCKWISEDIRECTION
SWITCHMODE LOAD CURRENT REGULA-
TION
PROGRAMMABLELOAD CURRENT
FEW EXTERNAL COMPONENTS
RESET INPUT & HOME OUTPUT
ENABLEINPUT
DESCRIPTION
The L297/A/D Stepper Motor Controller IC gener-
ates four phase drive signals for two phase bipolar
and four phase unipolar step motors in microcom-
puter-controlled applications. The motor can be
driven in half step, normal and wawe drive modes
and on-chip PWM chopper circuits permit switch-
mode control of the current in the windings. A
August 1996
Symbol Parameter Value Unit
V
s
Supply voltage 10 V
V
i
Input signals 7 V
P
tot
Total power dissipation (T
amb
= 70C) 1 W
T
stg
, T
j
Storage and junction temperature -40 to + 150 C
ABSOLUTE MAXIMUMRATINGS
feature of this device is that it requires only clock,
direction and mode input signals. Since the phase
are generated internally the burden on the micro-
processor, andtheprogrammer, is greatlyreduced.
Mounted in DIP20 and SO20 packages, the L297
can be used with monolithic bridge drives such as
the L298N or L293E, or with discrete transistors
and darlingtons.
TWOPHASE BIPOLARSTEPPER MOTORCONTROL CIRCUIT
DIP20 SO20
ORDERING NUMBERS : L297 (DIP20)
L297D (SO20)
1/11
PIN CONNECTION (Top view)
BLOCKDIAGRAM(L297/L297D)
2/11
L297
L297D
L297-L297D
N NAME FUNCTION
1 SYNC Output of the on-chip chopper oscillator.
The SYNC connections The SYNC connections of all L297s to be
synchronized are connected together and the oscillator
components are omitted on all but one. If an external clock source
is used it is injected at this terminal.
2 GND Ground connection.
3 HOME Open collector output that indicates when the L297 is in its initial
state (ABCD = 0101).
The transistor is open when this signal is active.
4 A Motor phase A drive signal for power stage.
5 INH1 Active low inhibit control for driver stage of A and B phases.
When a bipolar bridge is used this signal can be used to ensure
fast decay of load current when a winding is de-energized. Also
used by chopper to regulate load current if CONTROL input is low.
6 B Motor phase B drive signal for power stage.
7 C Motor phase C drive signal for power stage.
8 INH2 Active low inhibit control for drive stages of C and D phases.
Same functions as INH1.
9 D Motor phase D drive signal for power stage.
10 ENABLE Chip enable input. When low (inactive) INH1, INH2, A, B, C and D
are brought low.
11 CONTROL Control input that defines action of chopper.
When lowchopper acts on INH1 and INH2; when high chopper
acts on phase lines ABCD.
12 V
s
5V supply input.
13 SENS
2
Input for load current sense voltage frompower stages of phases
C and D.
14 SENS1 Input for load current sense voltage frompower stages of phases
A and B.
15 V
ref
Reference voltage for chopper circuit. A voltage applied to this pin
determines the peak load current.
16 OSC
An RC network (R to V
CC
, C to ground) connected to this terminal
determines the chopper rate. This terminal is connected to ground
on all but one device in synchronized multi - L297 configurations. f
1/0.69 RC
17 CW/CCW Clockwise/counterclockwise direction control input.
Physical direction of motor rotation also depends on connection
of windings.
Synchronized internally therefore direction can be changed at any
time.
18 CLOCK Step clock. An active low pulse on this input advances the motor
one increment. The step occurs on the rising edge of this signal.
PIN FUNCTIONS- L297/L297D
3/11
L297-L297D
N NAME FUNCTION
19 HALF/FULL Half/full step select input. When high selects half step operation,
when lowselects full step operation. One-phase-on full step mode
is obtained by selecting FULL when the L297s translator is at an
even-numbered state.
Two-phase-on full step mode is set by selecting FULL when the
translator is at an odd numbered position. (The home position is
designate state 1).
20 RESET Reset input. An active low pulse on this input restores the
translator to the home position (state 1, ABCD = 0101).
PIN FUNCTIONS- L297/L297D(continued)
CIRCUIT OPERATION
The L297 is intended for use with a dual bridge
driver, quad darlington array or discrete power
devices in step motor driving applications. It re-
ceives step clock, direction and mode signals from
the systems controller (usually a microcomputer
chip) and generates control signals for the power
stage.
Theprincipal functionsare a translator, which gen-
erates the motor phase sequences, and a dual
PWMchopper circuit whichregulatesthe current in
the motor windings.The translator generatesthree
different sequences, selected by the HALF/FULL
input. These are normal (two phases energised),
wave drive (one phase energised) and half-step
(alternately one phase energised/two phases en-
ergised). Two inhibit signals are also generated by
the L297 in half stepand wavedrivemodes. These
signals, whichconnect directlyto the L298senable
inputs, are intended to speed current decay when
a winding is de-energised. When the L297 is used
to drivea unipolar motor the chopper acts on these
lines.
An input called CONTROL determines whether the
chopper will act on the phase lines ABCD or the
inhibit lines INH1 and INH2. When the phaselines
are choppedthe non-activephaseline of each pair
(ABor CD) is activated(rather than interruptingthe
linethen active).In L297 +L298 configurationsthis
technique reduces dissipation in the load current
sense resistors.
A common on-chip oscillator drives the dual chop-
per.It suppliespulses at thechopper ratewhich set
the two flip-flops FF1 and FF2. Whenthe current in
a winding reaches the programmed peakvalue the
voltage across the sense resistor (connected to
one of the sense inputs SENS1 or SENS2) equals
Vref and the corresponding comparator resets its
flip flop, interrupting the drive current until the next
oscillator pulse arrives. The peak current for both
windingsis programmedbya voltagedivideron the
Vref input.
Ground noise problems in multiple configurations
can be avoided by synchronising the chopper os-
cillators. This is done by connecting all the SYNC
pins together, mounting the oscillator RC network
on one device only and grounding the OSCpin on
all other devices.
Symbol Parameter DIP20 SO20 Unit
R
th-j-amb
Thermal resistance junction-ambient max 80 100 C/W
THERMALDATA
4/11
L297-L297D
MOTOR DRIVINGPHASE SEQUENCES
The L297s translator generatesphase sequences
for normal drive, wave drive and half step modes.
The state sequences and output waveforms for
these three modes are shown below. In all cases
the translator advances on the low to high transis-
tion of CLOCK.
Clockwise rotation is indicate; for anticlockwise ro-
tation the sequences are simply reversed RESET
restores the translator to state 1, where ABCD =
0101.
HALF STEP MODE
Half step mode is selected by a high level on the HALF/FULL input.
NORMAL DRIVE MODE
Normal drive mode (also called two-phase-on drive) is selected by a lowlevel on the HALF/FULL input
when the translator is at an odd numbered state (1, 3, 5 or 7). In this mode the INH1 and INH2 outputs
remain high throughout.
5/11
L297-L297D
MOTOR DRIVINGPHASE SEQUENCES (continued)
WAVE DRIVE MODE
Wave drive mode (also called one-phase-on drive) is selected by a low level on the HALF/FULL input
when the translator is at an even numbered state (2, 4, 6 or 8).
Symbol Parameter Test conditions Min. Typ Max. Unit
V
s
Supply voltage (pin 12) 4.75 7 V
I
s
Quiescent supply current (pin 12) Outputs floating 50 80 mA
Vi Input voltage
(pin 11, 17, 18, 19, 20)
Low 0.6 V
High 2 V
s
V
I
i
Input current
(pin 11, 17, 18, 19, 20)
V
i
= L 100 A
V
i
= H 10 A
V
en
Enable input voltage (pin 10) Low 1.3 V
High 2 V
s
V
I
en
Enable input current (pin 10) V
en
= L 100 A
V
en
= H 10 A
Vo Phase output voltage
(pins 4, 6, 7, 9)
Io = 10mA VOL 0.4 V
Io = 5mA VOH 3.9 V
V
inh
Inhibit output voltage (pins 5, 8) I
o
= 10mA V
inh L
0.4 V
I
o
= 5mA V
inh H
3.9 V
V
SYNC
Sync Output Voltage I
o
= 5mA V
SYNC H
3.3 V
I
o
= 5mA V
SYNC V
0.8
ELECTRICAL CHARACTERISTICS (Refer to the block diagram T
amb
= 25C, V
s
= 5V unless otherwise
specified)
6/11
L297-L297D
Symbol Parameter Test conditions Min. Typ Max. Unit
I
leak
Leakage current (pin 3) V
CE
= 7 V 1 A
V
sat
Saturation voltage (pin 3) I = 5 mA 0.4 V
V
off
Comparators offset voltage
(pins 13, 14, 15)
V
ref
= 1 V 5 mV
I
o
Comparator bias current
(pins 13, 14, 15)
-100 10 A
V
ref
Input reference voltage (pin 15) 0 3 V
t
CLK
Clock time 0.5 s
t
S
Set up time 1 s
t
H
Hold time 4 s
t
R
Reset time 1 s
t
RCLK
Reset to clock delay 1 s
ELECTRICAL CHARACTERISTICS (continued)
Figure 1.
7/11
L297-L297D
APPLICATION INFORMATION
TWOPHASEBIPOLARSTEPPERMOTORCONTROL CIRCUIT
This circuit drives bipolar stepper motors with winding currents up to 2A. The diodesare fast 2A types.
Figure 2.
Figure 3 : Synchronising L297s
8/11
L297-L297D
DIM.
mm inch
MIN. TYP. MAX. MIN. TYP. MAX.
a1 0.254 0.010
B 1.39 1.65 0.055 0.065
b 0.45 0.018
b1 0.25 0.010
D 25.4 1.000
E 8.5 0.335
e 2.54 0.100
e3 22.86 0.900
F 7.1 0.280
I 3.93 0.155
L 3.3 0.130
Z 1.34 0.053
DIP20 PACKAGE MECHANICAL DATA
9/11
L297-L297D
DIM.
mm inch
MIN. TYP. MAX. MIN. TYP. MAX.
A 2.65 0.104
a1 0.1 0.3 0.004 0.012
a2 2.45 0.096
b 0.35 0.49 0.014 0.019
b1 0.23 0.32 0.009 0.013
C 0.5 0.020
c1 45 (typ.)
D 12.6 13.0 0.496 0.512
E 10 10.65 0.394 0.419
e 1.27 0.050
e3 11.43 0.450
F 7.4 7.6 0.291 0.299
L 0.5 1.27 0.020 0.050
M 0.75 0.030
S 8 (max.)
SO20 PACKAGEMECHANICAL DATA
10/11
L297-L297D
Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsibility for the
consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No
license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specification mentioned
in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied.
SGS-THOMSONMicroelectronics products arenot authorizedfor use as critical componentsin lifesupport devices or systems without express
written approval of SGS-THOMSON Microelectronics.
1996 SGS-THOMSON Microelectronics Printed i n Italy All Rights Reserved
SGS-THOMSON Microelectronics GROUP OF COMPANIES
Australia - Brazil - Canada - China- France - Germany - Hong Kong - Italy - Japan - Korea- Malaysia - Malta - Morocco - The Netherlands -
Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Ki ngdom- U.S.A.
11/11
L297-L297D
This datasheet has been download from:
www.datasheetcatalog.com
Datasheets for electronics components.