Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

Ibanez UE300 Servicemanual

Download as pdf
Download as pdf
You are on page 1of 8
Thanez SERVICE MANUAL NO. 012 MULTI-EFFECTS UE300 : kb &F EF & FF B iE EOE ECECE FORDE ECP a & SPECIFICATION: 1) COMPRESSOR /LIMITER @ Maximum Input Level © Maximum Outpet Level Output Level Range © Maximum Compression Ratio © Equivalent Input Noise fe Attack Time © Frequency Response 2) TUBE SCREAMER © Maximum Output Level © Maximum Amplitude © Equivalent Input Noise 3) STEREO CHORUS © Maximum Input Level » © Delay Time ‘© Sweep Speed « ‘© Input/Output level Ratio - ‘@ Equivalent Input Noise 4) OVERALL ‘© Input Impedance ‘@ Output | Impedance (© Output 2 Impedance serene ‘@ Ext Effect Loop Send Impedance ‘@ Ext, Effect Loop Receive Impedance ‘® Dimensions ; eo Weight ‘© Power Requirement > BLOCK DIAGRAM INPUT evereR | 46.5dltm at 4002 {048m at 4002 SOlim to. = Hd 40 —100d8m (IHF-A Input Shorted) - 6mSec to 20mSee 3012 to 20KHz ( + 5dB, ~24B) 068m a8 + —110d8m (IHF-A Input Shorted) 45.6dlim at 400H2 - 3.2mSec to 8.6mSec - 0.3H2 to 30Hz teal 98d8m (IHF-A Input Shorted) + $00Kohms Jess than 10K ohms less than 10K ohms + less than 10K ohms 00K ohms 310(W) x 1901) x 70(H) mmm (12.2 os 19kg (4.2 tbs.) LI7V AC 60Hz 31 220VAC to 240VAC SOHe 5.2 weg te i B % ouTpUT! aurren = SOUT a ourpuT2 ave TONE eurreR ve Oo gurreR SEND X7.5X28in) tr ExT. EFFECT oor RECEIVE “eu Leche sonal] “H slp Tae CONTROL Pa THEE TH 4c NORMAL CHECK LIST & ADJUSTMENT PROCEDURES (1) B.C. VOLTAGE 1) Check 1SV £1 at marked (@). (GND.= 9) 2) Check ripple noise less than 4mV at the same point above (11) COMPRESSOR/LIMITER 1) Set knobs as follows. ATTACK TIME =SHORT ‘THRESHOLD=LOW LEVEL=MAX 2) Adjust VRI for just zero voltage at R9 terminals. (uit) TUBE SCREAMER 1) Put 30mV 1 kHz sinewave into INPUT. 2) Check each wave form as follows. + DRIVE-MAX + DRIVE —MIN + DRIVE ~MAX = DRIVE—MIN STONE ~+5 TONE ——5 = TONE —~5 + LEVEL—MAX + LEVEL~MAX + LEVEL—MAX [v) STEREO CHORUS 1) Connect the FREQUENCY COUNTER and the SYNCHROSCOPE at marked CPI. 2) Set knobs as follows. SPEED=FAST WIDTH=MIN 3) Adjust VR3 for a frequency of SOkHz. 4) Set knobs as follows. SPEED=SLOW WIDTH=MAX 5) Check clock periodic time 9.625. 0 144 40, (IO4kH2 to 69kH2), also sweeping frequency 0.3H2, 6) Set knobs as follows. SPEED=SLOW WIDTH =MIN 1) Put O4Bm (0.77SmV) 400Hz sinewave into INPUT. 8) Adjust VR2 for a symmetrical clipped wave form at C23. (vy) oureuT 1) Check no switching shock noise. 2) Check each phase of OUTPUT. The phase of OUTPUT 2 is inverted against the phase of OUTPUT | satan | f

You might also like