Mercedes 190e

www.WorkshopManuals.co.
uk
EXIT
ngine timing, valvetrain 05
EXIT
www.WorkshopManuals.co.uk
ngine timing, valvetrain
Job No.
Checking and replacement of hydraulic valve clearance compensating element . . . . . . . . . . 05 - 211
Checking and correcting the installation position of hydraulic valve clearance . . , . . . . . . . . 05 - 214
-215
Checking and adjusting camshaft timing ......................................
-220
Removal and installation of camshaft .........................................
-235
Removal and installation of rocker arm bearing supports with rocker arms ..............
-240
Replacement of rocker arms and rocker arm bearing supports .......................
-250
Removal and installation of valve springs ......................................
-260
Checking valve springs ..................................................
- 270
Replacement of valve stem seals ...........................................
-280
Checking and machining valves ............................................
- 285
Checking and replacing valve guides .........................................
-290
Replacing valve seat ring .................................................
-291
Machining valve seats ...................................................
-310
Removal and installation of chain tensioner ....................................
-320
Replacement of timing chain ..............................................
-328
Installation of oil spray nozzle retroactively .....................................
-330
Removal and installation of tensioning blade ...................................
-340
Removal and installation of guide rails ........................................
-412
Removal and installation of idler gear shaft ....................................
-437
Removal and installation of oil pressure pump drive ..............................
05/'1
05-211
EXIT
Checking and replacement of hydraulic valve clearance

compensatlsn @lenlent
Preceding work:
AN cleaner removed (09-400 and 09-410).
Cylinder head cover removed (01-406).
Check
Cam
................................
05.0906 - 211il
position hydraulic element under test on the

base circle. Load hydraulic element for approx.
5 to 10 seconds. If the element drops, remove
it. To do this remove corresponding rocker arm
bearing support (OS- 235). If a leaking hydraulic
element is not found, check fitting position (OS214).
Note
When pressure testing the compensating
elements, do not press valves against the piston
crown (Numbers 1 and 2).
Valve clearance compensating element (58)
. . . .
Fill up reservoir chamber of valve clearance

compensating element on test with engine oil.
Press on ball valve with a suitable pin and vent
working chamber by pumping set bolt up and
down. Close ball valve, if necessary replenish
oil. After this no oil shall escape at ball valve
when compressed and set bolt may not drop. If
this is not the case, replace compensating
element (Number 3).
Note
If compensating element is satisfactory, check
oil bores in cylinder head, rocker shaft and
rocker arm for passage, and clean if required.
If several compensating elements are soft,
replace oil pipe in cylinder head (01-415), for
this purpose remove cylinder head (Ol- 415).
Replacement
. . . .
With oil reservoir chamber full and original

washer (57) push into the rocker arm up to the
stop on the snap ring (56)
(Number 4).
............
Install (05-235), at the same time fit original ball

socket (55).
Valve clearance compensating element (58)
Rocker arm bearing support (61)
Note
Use ball socket 103 055 00 24, if a new ball
socket is to be installed. Check and if required
correct fitting position (05-214, Numbers
5 and 6).
05.0906 - 211/2
EXIT
EXIT
Special tool
102 589 04 21 00
Hydraulic valve clearance compensation
43
46
51
55
56
57
59
60
61
62
63
64
65
a
b
C
Valve
Valve spring retainer
Rocker arm
Ball socket
Snap ring
Washer
Guide sleeve
Compression spring
Telescopic type ball
beanng traveler
Compression spnng
Ball (5 mm 0)
Set bolt
Sealing cap
Oil reservoir chamber
Working chamber
Return and venting bores
PO5-0019-15
Valve adjustment Is no longer required when

equipped with hydraulic valve clearance
adjusters
The maintenance-free hydraulic valve clearance
compensating elements located in the rocker
arms eliminate valve clearance, i.e. dimensional
changes in the valve train due to thermal expansion and wear are compensated by the elements. Valve train noise is low, because rocker
arm is in continuous contact with the cam.
05.0906 - 211/3
The hydraulic valve clearance compensating
elements consist of the following components:
l
Set bolt (64) with oil reservoir chamber (a)

as well as return and venting bores (c) and a
ball valve, consisting of a 5 mm 0 ball (63),
telescopic type ball bearing traveler (61) and
compression spring (62).
5 8 -
55-
Guide sleeve (59) with working chamber (b),

compression spring (60) and sealing cap
(65).
/P
po5-0033-15
The element can drop completely when the

engine is not running and the cam tip presses
against the rocker arm and thus also against the
element. Oil expelled from the working chamber
(b) flows via the annular gap (built-in clearance
between guide sleeve and set bolt) to the
reservoir chamber (a).
When the cam tip moves away from the rocker
arm, the set bolt (64) is relieved of load and the
compression spring (60) presses the set bolt
upwards until the rocker arm contacts the cam.
The vacuum, arising from the upward movement
of the set bolt, opens the ball valve, and oil flows
out of the reservoir chamber (a) into the working
chamber (b).
As soon as the cam presses against the rocker
arm and thus loads the set bolt, the ball valve
closes. The oil in the working chamber acts as
an hydraulically rigid connection and the
respective valve is opened.
When the engine is running, depending on
engine speed and cam position, the set bolt is
only pressed slightly downwards.
05.0906 - 211/4
EXIT
EXIT
The oil needed for operating the hydraulic valve

clearance compensating elements, flows from
the longitudinal channel and the transverse bores
in the cylinder head to the rocker arm bearing
points. From here it reaches the ring channel (f)
through the bore (h) in the rocker arm and the
reservoir chamber (a) via grooves in the washer
(57).
Any air in the reservoir chamber can separate
from the oil (solid oil), with the result that, if
necessary, defoamed oil is led to the working
chamber.
The oil quantity in the reservoir chamber is
sufficient to fill the working chamber under all
engine operating conditions. Any air in the
reservoir chamber can escape to the ring
channel (f) via the grooves in the washer (57)
and from there via the annular gap between
washer and rocker arm and the joint gap of the
snap ring (56).
In order that the hydraulic valve clearance

compensating elements can be supplied with oil
pressure corresponding to the respective engine
speed, oil flows unrestricted via nozzle (A) into
the longitudinal channel (a) in the cylinder head
(pressure-orientated oil feed). The nozzle
simultaneously blocks off the oil return,
preventing the channels up to the hydraulic
elements emptying when the engine is not
running.
P Ol-0087- 1s
The sealing cap (65) is shaped so that it secures

the hydraulic valve clearance compensating
element captive in the rocker arm.
Only store the compensating elements upright,
and do not dismantle them. It is essential that
rocker arm, compensating element, washer (57)
and ball socket (55) are installed in their original
position.
05.0906 - 211/S
EXIT
Checking
Position camshaft on the hydraulic element
1
under test so that the rocker arms contact the
cam base circle.
2 Press on the rocker arm with a hammer butt
or similar above the hydraulic valve clearance
compensating element for 5 - 10 seconds.
If one compensating element drops noticeably

compared to others, compensating element
should be removed. To do this, remove rocker
arm bearing support (05235) and press the
compensating element (58) together with the
washer carefully out of the rocker arm with an
aluminium or brass mandrel.
If a leaking compensating element cannot be

detected, try to move the rocker arm by hand.
If play is detected when doing this, check and
correct fitting position of the hydraulic valve
clearance compensating elements (05-214).
Caution!
When testing compensating elements, do not
press valves against the piston crown.
3 Fill reservoir chamber of the hydraulic valve

clearance compensating element with engine oil,
carefully press on ball valve in the setbolt with a
wire (approx. 1.5 mm (21) and press setbolt
downwards as far as the stop and release.
Repeat process two or three times.
PO5- 2011-13
05.0906 - 21116
EXIT
After this, press compensating element setbolt
heavily downwards for about 5 - 10 seconds with
hammer butt or similar. If the setbolt drops
noticeably when doing this, replace the compensating element.
Note
Compensating element must be vertical when
filling the working chamber as well as during the
test.
If compensating element does not drop

noticeably, check the respective oil bore in the
cylinder head (arrow) as well as the oil bores in
the rocker shaft and in the rocker arm for free
passage, and clean if required.
To do this remove rocker arm (05240).
If several compensating elements are loud or
soft the oil nozzle in the cylinder head should be
checked for firm seating and replaced if required.
Replacement
4 Slide new valve clearance compensating
element (58) with the original washer (57) into
the rocker arm (51) as far as the stop on the
snap ring (56).
Note
Install new compensating element with the
working chamber and reservoir chamber filled
with oil. (See Figure 3 for filling the hydraulic
valve clearance compensating element).
The grooves in the washer (57) must point to the
compensating element (58) (Figure 5).
05.0906 - 21117
51
I 56
PO5-2012-13
EXIT
5 Install rocker arm bearing support (05235).

In so doing install the original ball socket (55).
Note
Use ball socket Part No. 103 055 00 24 if a new
ball socket is installed.
PO5-2016-13
6 Check the installation position of the new

valve clearance compensating element, correct if
necessary (05-2 14).
7
Install in the reverse sequence.
05.0906 - 211/8
05214
EXIT
Checking and correcting the installation position of hydraulic valve

clearance compensating elements
Preceding work:
Air cleaner removed (09-400 and 09-410).
PO5-0026-39
Camshaft (1)
..........................
Measuring fixture
050906
- 214/l
. . . . . . . . . . . . . . . . . . . . . . .
position the cylinder under test so that rocker

arm (51) contacts the cam base circle
(Number 1).
mount, set dial gauge with 5 mm pretension, set
dial gauge pointer to "0".
Checking
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Turn pressure pad (06) to the right until a

detectable pressure point is reached.
Read setting range (residual stroke) on the dial
gauge. Reference value 0.5 - 2.4 mm. Correct
the fitting position if the residual stroke is larger
or smaller (Number 2).
. . . . . . . . . . . . . . .
Remove and install rocker arm bearing support

(05235). Remove hydraulic valve clearance
compensating element and slide into the rocker
arm again up to the snap ring stop. If residual
stroke is too small use a thinner washer (57), or
a thicker washer if residual stroke is too large.
Measure residual stroke again. If the specified
residual stroke has still not been achieved, a
thinner or thicker ball socket (55) can be fitted
(Numbers 3 to 6) if necessary.
Adjusting the residual stroke
Note
Before installation of the hydraulic valve
clearance compensating element fill reservoir
chamber with engine oil.
Rocker arm bearing support
. . . . . . . . . . . . . .
Install, repeat test (Numbers 7 and 8). Prior to

this, turn the engine with the starter and contact
handle a few times.
install in the case of repatr, when valve timing parts (rocker arm beanng supports, rocker arms, camshaft, etc.)
are renewed. Camshaft with normal cam base circle without identification letter next to the camshaft
identrfication number.
Install in the case of reparr, when valve timing parts (rocker arm beanng supports, rocker arms, camshaft, etc.)
2) Production:
are renewed. Camshaft with small cam base circle and rdentlficatlon letter E next to the camshaft
identification number.
3) Install In the case of repair, when valves and/or valve seat inserts have been resunk by machrnlng.
1) Production:
050906
- 214,'2
EXIT
EXIT
PO6-0087-1s
Washer
PO5-0025-13
Ball socket
Conventional tool
Oial gauge Al DIN 878
05.0906 - 21413
0.g .
Mahr, D-7300 Esslingen

Part No. 311000
EXIT
Note
The fitting position of the hydraulic valve
clearance compensating elements must be
checked
a) If there have been complaints of valve train
noise and no malfunctions have been
established when checking the compensating element in accordance with 05211.
b) If valve timing parts, which are installed or
mounted on the cylinder head (apart from
the camshaft timing gear, valve guides, valve
stem seals) have been renewed, or when
valves and/or valve seat inserts have been
machined.
For testing, all timing parts located on the
cylinder head must be installed correctly and
working chamber of valve clearance compensating elements must be filled with engine oil.
The tests can also be carried out when the

cylinder head is removed. To do this clamp
cylinder head with four cylinder head bolts
(arrows) on assembly board 102 589 00 59 00
(1). In this case turn the camshaft on rear flats
with a fork wrench (24 mm).
PO5- 2 0 3 4 - 1 3
05.0906 - 214/4
After the test, position camshaft so that indentation on the collar agrees with the edge
on the cylinder head (arrow).
In order to determine the specified fitting position
of the hydraulic valve clearance compensating
element, the residual stroke Z of the
compensating elements must be measured.
The permitted residual stroke is 0.5 to 2.4 mm.
If a residual stroke smaller than 0.5 mm or larger
than 2.0 mm is measured despite installing a
washer and a ball socket in accordance with the
installation specification table, compensation is
to be carried out with the next thinnest or
thickest washer or ball socket.
05.0906 - 21415
EXIT
EXIT
PO5-0024-39
Checking
1
Position camshaft by turning the crankshaft
so that the rocker arms contact the cam base
circle on cylinder under test.
2 Place measuring fixture 102 589 04 21 00 so
that the claws of the claw sleeve (03) contact
the ring shaped area around the hemispherical
mushroom pad of the guide sleeve (59).
05.0906 - 2146
Turn the pressure pad (06) by hand to the right
sufficiently until it contacts the washer (57,
previous picture), and a clearly detectable
pressure point is reached.
Note
The pressure pad must contact the washer and
not the rocker arm.
3 Insert measuring pin adapter (04) in the

central bore of the pressure pad (06), set dial
gauge measuring pin on the measuring pin
adapter with 5 mm pretension (small pointer) and
attach the dial gauge to claw sleeve bracket
(arrow). Position large dial gauge pointer on
zero by turning the dial gauge scale.
4 Turn pressure pad (06) slowly to the right

with a fork wrench (17 mm) on the hexagon until
a clearly detectable pressure point is reached.
Read off setting range (residual stroke) on dial
gauge. It must be 0.5 - 2.4 rnolp. In event of
smaller or larger residual stroke, correct
installation position of the hydraulic valve
clearance compensating element.
05 0906 - 214/7
EXIT
EXIT
Corrections
5 Remove rocker arm bearing support
(05235).
6 Press hydraulic valve clearance compensating element (58), together with the washer
(57), carefully out of the rocker arm with an
aluminum or brass mandrel, and finally slide into
the rocker arm up to the snap ring stop (56)
again. Use a thinner washer (residual stroke too
small) or a thicker washer (residual stroke too
large).
POS-2012-13
If specified residual stroke cannot be achieved

with the washers available (57), depending on
residual stroke measured, use a thinner or
thicker ball socket (55) (see note, on the washer
and ball socket tables).
Caution!
Before carrying out the installation fill reservoir
chamber of the hydraulic valve clearance compensating element with engine oil (05- 211,
Number 3).
POS-20
The grooves in the washer (57) must point in the

direction of the compensating element setbolt.
Install rocker arm bearing support (05-235).
8 Repeat tests, Numbers 1 to 3.

Note
Before carrying out the test turn the crankshaft a
few times by using the starter.
9 The installation is carried out in the reverse
sequence of the removal.
10 Check for leaks when engine is running.
05.0906 - 214/8
05215
EXIT
Checking and ad)usting camsbft timing
Preceding work:
AIM cleaner removed (09-400 and 09-410).
Cyltnder head cover removed (01-406).
PO6-0030-37
Checking
Dial
gauge
05.0906 - 215'1
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
bracket
(02)
...................
Position the No. 1 cylinder camshaft so that the

rocker arm @la) contacts the cam base circle.
Remove No. 1 cylinder rocker arm bearing
support (05235). Remove rocker arm and
hydraulic valve clearance compensating element
and adjustable rocker arm 102 055 00 01
together with adjusting screw 102 050 0220
(164) and fit locknut (163). Eliminate valve
clearance by turning the adjustment screw (164)
(Numbers 1 to 4).
Screw onto stud bolt at front left part of cylinder
head (Number 5).
Dial
gauge
(01)
.................... ... ..
Crankshaft
. . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjustment
. . . . . . . . . . . . . . . . .
Insert and put tip vertically on valve spring

retainer with 3 mm pretension (small pointer)
(Number 6).
Turn in the direction of rotation of the engine
until the small pointer on the dial gauge has
travelled back by 2 mm (valve stroke). The
value now read off on the vibration damper must
agree with the value in the table Intake valve
open (Number 7).
.........
Put engine on ignition TDC of No.1 cylinder

(Number 8).
. . . . .
. . . . . . . . .
Unbolt and bolt up, replace sealing ring

(41), 70 Nm (Numbers 9 and 19).
Oil pressure pump . . . . . . . . * . . .
. . . . . . . . .
Unbolt, set to one side with lines connected

(Number 10).
Camshaft timing gear . . . * . . . . . .
. . . . . . . . .
Align with timing chain.

Unbolt camshaft timing gear (Numbers
11 to 13 and 15).
. . . .
.., . . . . . . . . . . . . . .
Select from table and insert (Numbers

14 and 15).
Camshaft timing gear .
. . . . ., . . . . . . . . . . .
Assemble, note color marking, only install set

bolt.
Repeat tests (Numbers 6 and 7).
Tighten set bolt (9).
80 Nm (Numbers 16 to 18).
Chain tensioner locknut (40)
Woodruff key (6)
Dial gauge (01) and dial gauge (02)
. . . . . . . . . .
Rocker arm bearing support and rocker arm with

hydraulic valve clearance compensating element
05.0906 - 21512
Detach.
Install (Number 20).
Proceed with installation in reverse sequence
EXIT
EXIT
with 2 mm valve stroke
camshaft stamped at the rear
of the camshaft
Closes
before TDC
27128 )
35 3)/36 )/444)
11
(12O)
17
32
Value for used c WI In brackets.

1) Repalr camshaft wtth 0.5 mm larger bearing diameter.
2) Camshaft with wider cam (19 mm) and tin-plated.
3) ChIlled cast iron camshaft.
4) ChIlled cast Iron camshaft (with crowned cams) from 09/89.
. Special tools
363 589 02 21 00
001 589 66 21 00
001 589 67 21 00
Conventional tool
Dial gauge A 1 DIN 878
Note
It is sufficient during assembly work, if the
marking on the camshaft agrees with the
cylinder head edge in the ignition TDC position
of the No 1. cylinder (arrow). In special cases,
for example when there are performance
problems, the start of opening of No. 1 cylinder
intake valve is to be checked as described in the
following, and to be adjusted, if required. The
valve timings are measured at
2 mm valve stroke. Valve clearance must be
eliminated for this purpose.
05.0906 - 21513
e.g.
Mahr, D-7300 Esslingen

Bestell-Nr. 311000
Checking
1
Turn crankshaft until cam tips of No. 1
cylinder intake valve point downwards (valve
closed).
Caution!
The engine must not be turned at the camshaft
timing gear fixing bolt.
Under no circumstances turn engine backwards
during the measurement, otherwise considerable
measuring errors result, and chain tensioner lock
setbolt can spring forwards.
2 Remove rocker arm bearing support of No. 1

cylinder (05235).
3 Install intake valve rocker arm against the
rigid rocker arm @la) Part No. 102 055 00 01
together with the adjustment bolt (164) Part
No. 102 050 02 20 and the locknut (163) Part
No. 000936 008009 (05-240).
4
Install rocker arm bearing support, 21 Nm.
5 Install the dial gauge bracket with threaded

sleeve onto the stud on the front left part of the
cylinder head.
6
Insert dial gauge and attach so that tip is
exactly vertical on valve spring retainer with a

pretension of 3 mm (small pointer on the dial
gauge). Turn dial gauge clockface until large
pointer is on 0.
050906
- 21514
EXIT
EXIT
7 Turn crankshaft in direction of rotation of the
engine until dial gauge small pointer has returned
by 2 mm (valve stroke). In this positic? t?~
value on the vibration damper must agree Nrth
the value intake valve opens after TDC in the
valve timing table.
Adjustment
If valve timing settings have to be corrected, an
offset Woodruff key has to be installed, and a
new timing chain when chain length is excessive.
Woodruff keys are available in the following

stages:
Offset
mm
Part No.
0.7
0.9
1.1
1.3
621
621
621
621
991
991
991
991
for a correction
of approx.
04
02
01
00
67
67
67
67
6 CKA
8 CKA
9.5 CKA
11.5 CKA
CKA = CranK Angle
An offset of one tooth on the camshaft timing

gear produces approx. 20 at the crankshaft.
Offsetting the Woodruff keys to the right (in
direction of travel A) causes the valves to open
earlier and an offset to the left (6) causes the
valves to open later.
P05-0161-13
8 Position engine on ignition TDC of No. 1

cylinder.
05.0906 - 215 5
9 Unscrew hexagon cap nut (40) for chain
tensioner and remove sealing ring (41) as well
as compression spring (39) (see 05310).
Caution!
The chain tensioner hexagon cap nut is under
pressure from the compression spring.
10 Unscrew oil pressure pump (arrows) and set

to one side with the lines connected.
11 Align camshaft timing gear and timing chain.

12 Remove camshaft timing gear set bolt.
05.0906 - 2156
EXIT
EXIT
To do this hold in position with a fork wrench

(24 mm) on flats at the rear end of the camshaft.
Note
On vehicles with self-levelling suspension the
camshaft timing gear and driving sleeve are
attached by a bolt with hexagon recessed hole.
Take out the driving sleeve.
13 Remove camshaft timing gear.
14 Place cleaning rag over the timing case and

remove Woodruff key (6).
15 Insert selected Woodruff key.
16 Put on camshaft timing gear. In the process

note that the colour markings on the camshaft
timing gear and the timing chain align.
Do not torque the set bolt (9) yet.
17 Repeat test Numbers 6 and 7.
18 Torque camshaft timing gear set bolt (9) to
80 Nm. For this hold in position with a fork
wrench (24mm) on flats at the rear of the
camshaft.
PO5-2025-13
05.0906 - 21517
EXIT
19 Insert compression spring (39), replace
sealing ring (41), bolt in screw plug (40) and
tighten to 70 Nm.
20 Unbolt rocker arm bearing support from No.1

cylinder and withdraw rocker arm (51a) for
hydraulic valve clearance compensation.
21 Install rocker arm bearing support, tightening
torque 20 Nm (05- 235).
PO5-
22 Remove dial gauge and dial gauge bracket.

23 The remaining installation takes place in the
reverse sequence.
05 0906 - 21518
2021-13
05220
EXIT
Removal and installatisn of camshaft
Preceding work:
63
Piston of No. 1 cylinder

Screw plug (40)
. . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . .
position on ignition TDC, note markings

(Numbers 1 and 2).
of the chain tensioner, unbolt, bolt in,
70 Nm.
Warning!
Screw plug is under pressure. Remove
compression spring (39), replace sealing ring
(41)(Numbers 3 and 11).
Oil pressure pump (68)
. . . . . . . . . . . . . . . . . . .
Camshaft timing gear (4) and timing chain
05 0906 - 220/l
. . . . .
unbolt, bolt in, set to one side with lines

connected (Number 4).
align. When installing note markings. Screw
(9 and 9a), 80 Nm (Numbers 5 to 8).
All rocker arm bearing supports (61) with
rocker arms and oil pipe (67)
. . . . . . . . . . . . . .
Camshaft (1)
..........................
unbolt, bolt on, 20 Nm. Note oil pipe designs

(Number 9).
remove, replace, oil bearing points with engine
oil. Check condition of camshaft, note identification number. Position engine on ignition
TDC and check markings on camshaft and
vibration damper (Number 10).
Special tools
001 589 66 21 00
001 589 72 21 00
Test values
I New value
Permitted deviation from true running
when locating camshaft in bearing
positions 1 and 5
Camshaft bearing play
Camshaft journals 0
Scleroscope hardness of the cams
050906 - 22012
I Wear limit
At the seat of
camshaft timing gear
0.025
At the bearing points

2, 3 and 4
I 0.030
I
II
radial
I 0.050 - 0.091
I 0.11
axial
I 0.070 - 0.150
I 0.18
Normal dimension
1 32.000 - 32.025
I-
Repair stage
1 32.500 - 32.525
I-
I 70 - 82
I 63
EXIT
Camshaft id ntification numbers and val
Engine
Camshaft identification
number stamped at rear of
camshaft
102.96
102.985
Intake valve
27128 )
35 3)/6 )/444)
Value for used chains in brackets.

l) Repair camshaft with 0.5 mm larger beanng diameter.
2) Camshaft with wider cams (19 mm) and tin-plated.
3) ChIlled cast iron camshaft.
4) ChIlled cast iron camshaft (with crowned cams) from 09189.
Note
The camshaft supported on 5 bearings is drilled
hollow. The bearing points are supplied with oil
via the longitudinal bore (10.5 mm @), which is
sealed at the front with the camshaft timing gear
set bolt and at the rear with a pressed cover
(arrow). The oil feed takes place via a groove
(360) and a transverse bore (3.5 mm 0) in the
rear journals.
The diameter (D) of all 5 bearing points is
32 mm (repair stage 32.5 mm).
A fork wrench can be put on flats (A, 24 mm) at
the rear end of the camshaft for turning the
camshaft when camshaft timing gear is removed
and for holding in position when loosening and
tightening camshaft timing gear set bolt. The
collar (B), which runs in a groove in the cylinder
head, locates the camshaft axially.
05.0906 - 220/3
Exhaust valve
32
EXIT
EXIT
PO5-0145-53
The marking for the ignition TDC position of the

No. 1 piston is placed on this collar. It must
match up with the edge on the cylinder head
(arrow).
The camshaft can be removed from above. The

rocker arm bearing supports and the camshaft
timing gear have to be removed for this.
If the camshaft is to be replaced, all the
rocker arms have to be replaced as well.
In the event of scored bearings or pronounced
striation, the camshaft bearings in the cylinder
head and in the rocker arm bearing supports can
be bored out by 0.5 mm and a camshaft with
over dimensioned bearing spigots installed
(01-419).
05 0906 - 220/4
EXIT
The running in and wear characteristics have
been improved by short- stroke honed camshafts
(formerly tin-plated).
Introduced in Droduction: Januarv 1986

Engine end number
Vehicle identification end
Since October 1987 camshafts have been fitted

with 19 mm wide tinplated cams (formerly
18 mm).
Identification number: 39
Note
As a temporary measure this camshaft has been
given the identification number 3.
Model
201.028
05.0906 - 220/5
Engine
I 102.985
Engine end number
I 019320
I 062484
I 416851
I 435608
Since 1988, in order to avoid camshaft wear,
chilled cast iron camshafts and rocker arms with
soldered on hard metal pads have been
equipped.
If the chilled cast iron camshaft has been
installed on previous engines, rocker arms with
hard metal cam follower must also be installed.
As a temporary measure this camshaft has been
given the identification number 5.
Introduced in woduction: October 1988

Model
201.028
Engine
Engine end number

Manual transmission
I 102.985
I 027671
Engine end number

Automatic transmission
I 077053
From 09189 a chilled cast iron camshaft with

crowned cams has been installed. This
camshaft is also supplied as a replacement part.
Identification number: 44
Engine end number
05.0906 - 220/6
EXIT
EXIT
In order to improve camshaft lubrication the oil
feed bore in the cylinder head has been enlarged
from 3 mm to 4 mm 0 (arrow).
The oil groove in the rocker arm bearing support

has also been widened from 4 mm to 5.5 mm
(arrow).
PO&2207-1s
The injection bores in the oil pipe for camshaft

lubrication have a different diameter depending
on position.
A
01,8(4x)
01,3(4x)
03.5
04
A
B
05.0906 - 22017
Oil pipe - first design

Oil pipe - second design
4
POS-0162-13
Introduced in Droduction: Januarv 1988
Model
201.028
Engine
I 102.985
Engine end number

Manual transmission
022013
Removal and installation

1
Position piston of No. 1 cylinder on ignition
TDC.
2 Marking on camshaft collar must align with

the edge on the cylinder head (arrow).
Before turning the crankshaft, switch off the
ignition and remove the plug for the inductive
sensor at the switching unit.
Caution!
Do not turn the engine by the camshaft timing
gear set bolt.
Do not turn the crankshaft backwards.
05.0906 - 220/8
Engine end number

EXIT
3 Unscrew the chain tensioner hexagon cap
nut (40) and remove sealing ring (41) as well as
compression spring, tightening torque 70 Nm
(05-310).
Caution!
The chain tensioner hexagon cap nut is
pressurized by the compression spring.
4
Unbolt, bolt on oil pressure pump (68)
(arrows) and put to one side with the lines
connected.
Align camshaft timing gear and timing chain.
05.0906 - 22019
EXIT
EXIT
6 Remove camshaft timing gear, remove
timing chain and place in the timing case,
tightening torque 80 Nm.
4
7 Remove and install Woodruff key (6) and
spacer washer (7).
Installation note
Note color markings on camshaft timing
gear and timing chain.
Assemble camshaft timing gear so that on the
single roller chain the wide collar points to the
camshaft and on the dual roller chain the
curvature points to the camshaft.
8 In order to loosen or tighten up camshaft

timing gear hold in position with flats at the rear
of camshaft with a fork wrench (24 mm).
9 Remove and install rocker arm bearing

supports (61) (05-235), tightening torque
20 Nm.
10 Remove camshaft. Before installing
lubricate all bearing points with engine oil.
Check, whether the marking on set collar aligns
with edge on the cylinder head.
Installation note
If camshaft is to be replaced, all rocker arms and
rocker shafts have to be replaced as a set.
05.0906 - 220/10
8
9
POS-0038-13
11 Install hexagon cap nut (40) and compression spring (39) with new sealing ring (41),
12 The installation proceeds in reverse

sequence.
05.0906 - 220111
EXIT
EXIT
Removal and installation of rocker arm bearing supports with

rocker arms
05-235
Preceding work:
AW cleaner removed (09-400 and 09-410).
61
05-0046-35
Engine
Oil
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
pipe
(67)
...........................
............
turn, so that rocker arm of bearing support

being removed is on base circle of cam
(cam tips pointing downwards).
remove, install (Number 2).
remove, install, 20 Nm (Number 3).
Installation note
Install ball socket (55) in original position.
Note identification number on cylinder head and
camshaft bearing cap.
Special tool
05 0906 - 235/l
EXIT
Note
The five bearing bores for camshaft support are
each located half in the cylinder head and on top
in the four rocker arm bearing supports. The
front rocker arm bearing support has two half
bearing bores.
Each of the four bearing supports is attached

with four bolts (63) and with two installation
sleeves (60). Each bearing support
simultaneously acts as a rocker arm carrier.
PO5 -0039 -13
The rocker arm bearing supports can be

distinguished by the following features.
Front bearing support

Code No. 1. Two bearing positions (arrows).
Center bearing supports

Code No. 2 and 3. These two bearing supports
are the same apart from the identification
numbers.
1 IV
Rear bearing support
Code No. 4. Connection bore for oil pipe
(arrow).
05.0906 - 23512
POl-2076-13
EXIT
The two oil grooves (arrows) act as oil supply to

elements.
PO5-2036-13
The oil pipe for camshaft lubrication is supplied

with oil via the groove (arrow) on the rocker arm
bearing support.
POI-220?-19
The rocker arm bearing supports should not be

confused with each other. They are therefore
identified on the right-hand side with the
Numbers 1, 2, 3 and 4 from the front to the
back. The identification of the bearing support
must agree with the number, which is cast in the
cylinder head (arrows).
In the replacement parts area the bearing
supports are made individually and without code
numbers stamped on. The corresponding code
number is to be applied after installation.
05.0906 - 23513
EXIT
The rocker arms for operating the valves are
supported individually on a rocker shaft fitted in a
bearing support on both sides (arrows).
I I,
// PO6-207%13//
Rocker arms with soldered on cemented carbide

tips have been installed since October 1988
(arrow).
PO5-2038-13
The oil required for lubricating the rocker arm

bearings reaches the rocker arm bearing shaft
(50) and hydraulic valve clearance compensating
element via a longitudinal channel in the cylinder
head and a feed bore in the bearing support
(which is also the set bolt bore).
1
Camshaft
50 Rocker shaft
51 Rocker arm
55 Ball socket
58 Hydraulic valve clearance
compensating element
68 Oil pipe
05 0906 _ 23514
The rocker shaft is secured in the axial and
rotary direction by a bearing support set bolt.
For this a half bore is attached to the shaft, in
which one half of the screw shaft is located
(arrow).
An M8 thread (D) has been incorporated in the
front face for installation and removal of the
rocker shaft.
Removal, installation
1
Turn engine so that the camshaft tips of the
bearing support being removed point downwards
and rocker arms are on the base circle.
2 Remove oil pipe (67), to do this unbolt, bolt
up the two bolts (63) on the pipe clamps,
Remove, install relevant rocker arm bearing

3
support, tightening torque 20 Nm.
Note
Loosen seized bearing supports using light blows
with a plastic hammer.
The ball sockets (55) on the hydraulic elements
can stick or fall down when removing the bearing
support. Install ball sockets in their original
positions.
install the rocker arm bearing support so that the

support areas for the oil pipe point rear-wards,
the code numbers of the bearing supports are on
the right-hand side (direction of travel) and
correspond to the number cast on the cylinder
head (arrows).
05.0906 - 23515
EXIT
EXIT
eplacement of rocker arms and rocker arm bearing supports

Preceding work:
Air cleaner removed (09-400 and 09-410)
61
Camshaft
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
position so that rocker arms of bearing support

being removed is on base circle of the cam
(Number 1).
Oil
(67)
remove, install (Number 2)
pipe
Bearing
support
Rocker shaft (50)
...........................
(61)
. . . . . . . . . . . . . . . . . . . . . . .
New bearing support (61)
05.0906 - 240/l
.....................
. . . . . . . . . . . . . . . . .
remove.
pull out with impact extractor 116 589 20 33 00
and extension 616 589 00 34 00. Lubricate new
rocker arm and rocker shaft and install. Prior to
this rebuild hydraulic valve clearance
compensating element (05-211, Numbers
4 and 5).
install with rocker shaft without rocker arm,
20 Nm (Numbers 6 and 7).
Camshaft
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bearing support (61) . . . .
. . . . . . . . . . . . . .
turn and check for smooth running, possibly fit

new bearing support (Number 8).
remove, complete with rocker arm (51) and
install rocker shaft (50) and bearing support
(Numbers 9 and lo), 20 Nm.
Special tools
7
Threaded pm M8,
116589203300
001 589 66 21 00
116 589 20 33 00
Data
Rocker arm bore
Rocker shaft diameter
Radial clearance between rocker arm and rocker shaft
Rocker arm bearing support bore
Note
Only one bearing support can be replaced
on an engine, otherwise camshaft binding will
result.
05.0906 - 2402
18.016
18.027
__
17.089
=TKEB0.016
0.038
i 8.000
i
8-01
EXIT
Only rocker arm bearing supports where
camshaft bearing half bore is 0.05 mm larger
than on production parts are supplied as spare
parts. This prevents the camshaft binding when
replacing a bearing support.
In the event of bearing seizure or pronounced
striation the camshaft bearings can be bored out
by 0.5 mm and a camshaft with oversized
journals installed (01-419). These camshafts
have different code numbers
(05215 and 05-220).
If the bearing supports are put together without
rocker shafts, tighten the set bolts to max. 15
Nm, otherwise the shaft bores distort.
The radius on the rocker arm has been changed

in order to increase the clearance between the
rocker arm and the valve spring retainer (arrow).
05 0906 - 24013
EXIT
EXIT
In order to avoid camshaft wear, rocker arms
with soldered on cemented carbide tips have
been installed (arrow).
Only this rocker arm is still supplied as a
replacement part.
These rocker arms may only be installed
together with the chilled cast iron camshaft.
PO5-2038-13
0 5 . 0 9 0 6 - 24014
Replacement
a) Rocker arms and rocker shafts
1 Turn the engine so that the cam tips of the
bearing support being removed point downwards
and the rocker arms are on the base circle.
2
Remove, install oil pipe (67).
3 Remove bearing support.

4 Pull out rocker shaft with the impact
extractor 116 589 20 33 00 and extension
616 589 00 34 00 or with an M8 bolt.
5 Lubricate new rocker arm and rocker shaft
and install.
b) Bearing suppoft
6 Lubricate new rocker shaft and install without
rocker arm in the new bearing support.
Note
Insert the rocker shaft so that the half-bore
(arrow) is located in one half of the screw shaft.
7 Put on bearing support, tighten set bolts (63)

to 20 Nm, install oil pipe (67).
05.0906 - 24015
EXIT
8 Turn camshaft by the fiats with a fork
wrench (24 mm) and check for ease of movement. If binding occurs, remove the bearing
support again and replace with another.
9 Remove new rocker arm bearing support
and pull out rocker shafts (Figure Number 4).
10 Lubricate rocker arms and rocker shafts and
install in bearing support.
11 The installation proceeds in the reverse
sequence.
05.0906 - 24016
EXIT
emoval and installation of valve springs
Preceding work:
Spark plugs removed (15-018).
63
5-0048-37
A. Cylinder head removed

Cylinder head
. . . . . . . . . . . . . . . . . . . . . . . . .
clamp on assembly board 102 589 00 59 00.

Remove, install rocker arm bearing supports.
Attach support bridge 102 589 01 59 00 to
cylinder head. Remove, install valve springs
with the lever compressor 601 589 02 61 00.
. Cylinder head Installed

Piston of the relevant cylinder
Oil
pipe
0 5 0 9 0 6 - 250/l
(67)
. . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . .
position on ignition TDC (Number 1).

remove, install (Number 2).
EXIT
............
remove, install, 20 Nm (Number 3).
Repair note
Lubricate camshaft journals.
Ball sockets (55) must be installed in the same
position again.
Note installation position of the rocker arm
bearing bolt.
support
..**.............*....*...
Cylinder leakage tester

Valve
totters
. . . . . . . . . . . . . . . . . . .
(45) . . . . . . . . . . . . . . . . . . . . . . .
install 102 589 01 61 00 (Number 4).

Disconnect, connect to the relevant cylinder
(Number 5). Pressurize cylinder.
remove and install with the lever compressor
601 589 02 61 00 and magnet 116 589 06 63
00. Remove, insert valve springs (Numbers 7
to 9).
Installation note
Install valve spring so that the color marking and
the narrower coil point downwards.
Special tools
001 589 72 21 00
116 58906 63 00 I
050906 - 25Ot2
119 58901 61 00
.
/
102 589 00 59 00
EXIT
Conventional tool
Cylinder leakage tester
e. g.
Bosch, E F A W 210 A
Sun, CLT 228
Note
Valve springs and valve spring retainers with
scoring on the mounting surfaces must be
replaced.
- 4 0
-54
PO5-
The valve springs act progressively and must be

installed so that the color marking (narrow coil)
points towards the thrust collar (47).
Color marking : yellow/red or
violet/red
A thrust collar (47) is inserted under the valve
springs, which is supported on the cylinder head
via anti-rotation lugs.
As on all other engines, the valve spring thrust
bearing at the top forms valve spring retainers
(46) which are attached to the valves with valve
cone halves (45).
05.0906 - 25013
EXIT
A. Cylinder head removed
When the cylinder head is removed the valve

springs can be removed as follows:
Clamp cylinder head with four cylinder head

bolts (arrows) on assembly board
102 589 00 59 00 (1). Remove rocker arm
bearing supports with rocker arms and camshaft.
Attach support bridge 102 589 01 59 00 to the

cylinder head and remove the valve springs with
the lever compressor.
05.0906 - 250/4
EXIT
EXIT
Cylinder headl installed
Removal, installation
1
Put piston of the relevant cylinder on ignition
TDC.
Note
The respective pistons are in the ignition TDC
position, when the markings on vibration damper
shown in the adjacent drawing are beneath the
TDC pointer.
PO3-0058-13
Marking
I TDC
Piston at TDC on
cylinder
I 180
2 and 3
1 and 4
I
Removal and installation of oil pipe (67).
3 Remove and install the required rocker arm

bearing support (61) tightening torque 20 Nm.
Installation note
Before installing rocker arm bearing support
lubricate camshaft journals.
Install the rocker arm bearing support so that the
support area for the oil pipe points rearwards
and the code number is on the right (in the
direction of travel).
The ball sockets (55) must be installed in the
same position again.
05.0906 - 2503
4
Bolt up, unbolt support for lever compressor,
5 Connect cylinder leakage tester and pressur,ize cylinder.
6 Mount lever compressor on the support and

install the valve spring retainer.
7 Compress valve spring and take out valve
cone halves with the magnetic lever.
Caution!
Do not remove the valve springs without
compressed air in the cylinder, otherwise
damage can occur due to contact between the
valves and the piston.
8 Remove, install valve spring retainers and

valve spring.
9 Check valve spring (05260) and valve
spring retainers, replace as necessary.
10 Installation is the reverse of removal.
050906
- 250,6
EXIT
Checking valve springs
05260
PO5-0032-13
Data
_
Valve spring
Part no.
I
Colour
identification
(F)
053 02 20 yellow-red
or
violet-red
102 053 11 20 violet-yellow
orange
or
yellow-yellow
orange
Note
When carrying out repairs valve springs are to
be checked for corrosion before reuse and to
be replaced as necessary.
05.0906 - 260'1
Outside
0 mm
Wire
0 mm
Free
length
Spring force at the

pre-loaded length
EXIT
EXIT
Checking
1
Check valve springs with a valve spring
tester or with a spring test scale.
2
Check spring force at the specified length.
3 If the limit value is not achieved, replace

valve springs.
PO5-2129-1
05.0906 - 260/2
05270
EXIT
Replacement of valve stem seals
Preceding work:
Spark plugs removed (1 S-01 8).
Valve springs removed (05-250).
48
PO5-0047-34
Valve stem seal (48 and 49)
Special tools
05.0906 - 270/l
. . . . . . . . . . . . . . .
extract with special tool 104 589 00 37 00.

Debut-r valve stem at the groove. Replace
hammered valve cone halves, spring seats and
thrust collars.
Lubricate valve stem seal and insert.
Special tool 601 589 02 43 00. Note color
marking, use assembly sleeve.
EXIT
Note
The valve stem seals including assembly sleeves
are supplied in the repair set. Since September
1988 standardized valve stem seals in Viton
(formerly Polyacrylic) are installed for intake and
exhaust valves. The valve stem seals must not
be interchanged due to the different inside 0.
Distinguishing features:
Intake valve stem seal (48)
Chamfer (arrow) relieved
d = 7.3 mm
Wire ring : phosphated (black)
Color: brown
PO5 -0041-13
Exhaust valve stem seal (49)

Chamfer (arrow) inclined
d = 8.2 mm
Wire ring : bright galvanized (yellow)
Color: brown
-d-
PO5 -0040 -13
Valve guides, which are opened out at the

retaining groove for the valve stem seal, must be
replaced.
When installing the valve stem seal on the intake
valves it is absolutely essential that the plastic
sleeve, which is enclosed in the repair set, is
placed on the valve stem, because without the
sleeve damage to the sealing lip of the valve
stem seal is unavoidable.
05 0906 - 270/2
EXIT
As a temporary measure valve stem seals with a
smaller inlet 0 c = 16 mm (previously
17.5 mm) have been installed.
Identification: revised outside contour
A Temporary design
B Production design
Intake valve stem seal
PO5-0168-13
Introduced inproduction: January to Februarv 1986

Model
201.024
Engine
I 102.985
Engine end number

Manual transmission
I 003217 - 003513
Engine end number

I 029482 - 031994
Exhaust valve stem seal
PO5-0169 -13
Introduction of Viton valve stem seal
Color identification: brown
Introduced in production: June 1988

Model
201.028 @
05.0906 - 27013
Engine
I 102.985
Engine end number

Manual transmission
Engine end number

I 025442~~ ~~~[074595
~ - ----
EXIT
05280
EXIT
Checking and machining valves
PO5-0042-15
PO5 - 0 0 4 3 - 1 5
Checking
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
clean valves.
Visual inspection:
Valves with burnt valve heads, insufficent val\
head height (h) worn or grooved valve stem
must be replaced (Number 1).
Checking
............................
Measure valve stem eccentricity. Replace va ,Ive

when eccentricity is more than 0.03 mm
(Number 2).
Machining valve seat .....................
05.0906 - 280/l
Note operating instructions for machining

equipment.
Note adjustment angle a 45 + 15. Weplac 8
valve when maximum tolerances are reached
(Numbers 3 and 4).
Conventional tools
Valve cone grinding machine
or
e.g.
Valve cone turning equipment
e.g.
Krupp,
D-5309 Meckenheim
VS Model
Hunger,
D-8000 Miinchen 70
Type VKDRl,
Part Number 203.00.200
Data
Valve head @ D
the valve head
Identification on end of stem

Engine
I Inlet valve
I Exhaust valve
102.985
05.0906 - 280/2
E 102 08
A 102 03 27
EXIT
EXIT
42
PO5
-0043
-15
42 Intake valve
Note
The exhaust valve stem is chrome-plated on
these engines and filled with sodium due to high
temperatures in the combustion chamber.
Warning!
Unserviceable sodium filled valves must be
neutralised before scrapping. They must
therefore be collected and sent to:
Mercedes Benz AG
Werk Marienfelde
DaimlerstraOe 145
Anlieferstelle KST 3153
Arbeitsvorbereitung TAI
43 Exhaust
valve
After machining or replacing valves, the installed

length of hydraulic valve clearance compensating
elements must be checked and corrected if
necessary (05214).
05 0906 28013
POS-0042 -15
EXIT
Checking and machining
1
Clean valves and carry out visual inspection.
Valves with burnt valve heads with insufficient
valve head height h and with worn or scored
valve stem are to be replaced.
PO50035-l 3
2 Measure valve stem eccentricity. Replace

valve when an eccentricity of more than
0.03 mm is measured.
3 Machine valve seat. Note operating

instructions of the machining equipment and
adjustment angle
a 45 + 15.
4 Measure valve seat eccentricity and valve
head height h. Replace valve if the limit
values are reached.
05.0906 - 28014
05285
EXIT
Checking and replacing valve guides
PO50057-35
Valve stem seal seat (3)
. . . . . . . . . . . . . . . . . .
check for wear. If the valve stem seal is no

longer firmly seated, replace valve guide,
special tools 103 589 02 15 00, 103 589 03 15
00.
Valve guide (54 and. 56)
. . . . . . . . . . . . . . . . . .
clean, check, special tools

000 589 10 68 00, 102 589 00 23 00 and
117 589 03 23 00. If no-go
the pin of the
checking mandrel can be slid in longitudinally or
laterally to the full extent (6.5 mm), replace
valve guide. Special tools 103 589 02 15 00 and
103 589 03 15 00. Insert: Super cool in liquid
nitrogen approx. (3 minutes), special tools
102 589 04 15 00 and 102 589 05 15 00. See
repair note. After insertion check inside 0 with
testing mandrel, special tools
102 589 00 23 00 and 117 589 03 23 00; if
required, ream, special tools
000 589 21 53 00 and 000 589 10 53 00.
05.0906 - 2831
Base bore for valve guide
in the cylinder head (1) . . . . . . . . . . . . . . . . . . .
Valve seat ring (53 and 54)
. . . . . . . . . . . . . . . .
check before inserting a valve guide.

Special tool 117 589 05 23 00. If normal
dimension valve guide can be used;
Ream base bore with reamer 14.035 mm 0,
1105890300
When the checking pin can be inserted to the
full extent, broach base bore to 14.2 mm 0.
Special tools 115 589 00 53 00,
102 589 00 63 00, 102 589 01 63 00 and
102 589 02 63 00.
See repair note.
after installing a new valve guide check for
eccentricity, if necessary machine (05-291).
Special tools
000 589 10 68 00
117589052300
103589031500
103 589 02 15 00
102 589 00 23 O(
117589032300
115589005300
110589035300
102 589 00 63 00
02 589 02 63 0
102589016300
050906 - 285/2
102 589 05 1500
000 589 10 53 00
EXIT
EXIT
Conventional tool
e.g.
Cylinder head clamping fixture
f-lunger,
D-8000 Munchen 70
Part Number 221.60.000
Exhaust valve
Normal
dimension
Repair stage
Part Number
11020501724
Outside rz! (D)
114.044 - 14.051 114.214 - 14.222 114.044 - 14.051
Color identification
Base bore in cylinder head
Overlap
Valve guide inside @ (A)
Length (L)
grey-brown
11020501024
Normal
dimension
red
11020501824
grey-brown
Repair stage
11020501324
14.214 - 14.222
red
114.030 - 14.035 114.198 - 14.203 114.030 - 14.035 114.198 - 14.203
I 0.009 - 0.021
IO.01 1 - 0.024
1 0.009 - 0.021
0.011 - 0.024
8.000 - 8.015
8.000 - 8.015
9.000 - 9.015
9.000 - 9.015
I 46.0
I 46.0
I 51.0
I 51.0
Note
Valve guides are made of different materials on
the intake and exhaust side.
Intake valve guide (54): copper olours
Exhaust valve guide (56): brass colors
PO&0060-13
Valve guides produced by another manufacturer

have been installed between June and
September 1986.
05.0906 - 2850
EXIT
Engine
Model
Engine end number
1) not recorded
Broach base bore in cylinder head

(repair stage)
Remove rust and clean the cylinder head
thoroughly, particularly the inside of valve I seat
rings.
Select correct guide sleeve (2) and remove
swat-f from the cutting edge of broach (1) with a
stiff plastic brush or similar.
Note
The broaching tool cutting edges must be
cleaned before every broaching process. Provide
guide sleeve, base bore and complete broach
with ample supply of kerosene.
Slide broaching tool in direction of broaching into

the guide sleeve, so that when putting the guide
sleeve on the valve seat ring (3) the first broach
cutter is inserted in the base bore. When doing
this, note that the correct side
(A or B) of the guide sleeve is placed on the
valve seat. Center guide sleeve by rotary movements in valve seat ring.
Note
Drive home the broach briskly with an aluminium
mandrel, approx. 130 mm long, and a plastic
hammer of approx. 250 g.
1 Broach
2 Guide sleeve
3 Valve seat ring
05.0906 - 28514
PO5-0163-17
Inserting valve guide
Drive in the valve guides with impact mandrel
and hammer, when the valve guides are not
super cooled and cylinder head is not heated up.
Coat valve guides with wax or oil before driving
in.
Guide sleeve - valve seat allocation to enaine

Valve seat
Engine
Guide sleeve
Part No.
Base bore 0
in cylinder head
Intake
102.922/924
102.962.963
102 589 01 63 00
14.2mm
Exhaust
05.0906 - 2855
I 102.985
I 102 589 02 63 00
I 102.985
I 102 589 00 63 00
EXIT
05290
EXIT
eplacing valve seat ring
PO5-0052-35
Valve seat ring (52 and 53)

Valve guides (54 and 56)
Base
bore
. . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . .
(D2)
.........................
Machined base bore
. . . . . . . . . . . . . . . . . . . .
Valve seat ring repair stage

Cylinder head (1)
Valve
seat
05.0906 - 290/l
ring
. . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . .
.........................
unscrew with seat ring turning tool

Note turning tool operating instructions.
check, replace if necessary (05-285).
measure.
Note
A new valve seat ring with normal dimensions
can be used, when specified overlap is present.
If minimum overlap is not achieved, machine
base bore for valve seat ring.
measure.
skim, so that the specified overlap is achieved.
heat up in water bath.
Super cool with liquid nitrogen and stamp with a
suitable mandrel. Machine valve seat
(05-291).
Special tools
id
I
!,i
102 589 00 23 00
117589032300
Conventional tools
e.g.
Hunger,
D-8000 Munchen 70
Part No. 221.60.000
Ring seat turning tool
e.g.
Hunger,
D-8000 Munchen 70
Size 2, Part No. 220.03.110
Valve seat turning device
e.g.
Hunger,
D-8000 Munchen 70
Type VDSN l/45/30,
Part No. 236.03308
Test set for valve seats
e.g.
l-iunger,
D-8000 Munchen 70
Part No. 216.93.300
Internal measuring instrument

(measuring range 35 - 100 mm)
e.g.
Mahr,
D-7300 Esslingen
Part No. 844 N
External micrometer
(measuring range 25 - 50 mm)
e.g.
Mahr,
D-7300 Esslingen
Part No. 40 S l-f
05.0906 - 29012
EXIT
EXIT
Data
I Intake
I Exhaust
PO6-0064-N
Exhaust
05.0906 - 29013
EXIT
Intake
Note
The valve seat rings are sintered metal on
account of lead free fuel.
These hardened valve seat rings temporarily had

a step (arrow) on the inside of the ring.
PO5 -0164 -11
This step must be turned off in order to machine

the valve seat ring. There is a repair valve seat
ring with larger outside diameter as a replacement part for all valve seat ring designs. After
renewing valve seat rings, the fitting condition of
necessary (05214).
05.0906 - 29014
05291
EXIT
Machining valve seats
PO5-006
Valve guides (56)

Valve
seats
. . . . . . . . . . . . . . .
(53)
........................
check (05285).
machine in accordance with manufacturers
operating instructions. See data for adjustment.
Note
Only loosen pilot, when eccentricity of valve
seat ring has been checked.
Valve seat eccentricity
Valve seat width (b)
. . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . .
Valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
05.0906 - 29l;l
check (Number 3).

measure, correct if required (Number 4).
insert and measure, stand off (A).
EXIT
Conventional tools
e.g.
Hunger,
D-8000 Munchen 70
Part No. 221.60.000
Valve seat turning equipment
e.g.
Hunger,
D-8000 Munchen 70
Type VDSN l/45/30,
Part No. 236.03.308
Test set for valve seats
e.g.
Hunger,
D-8000 Munchen 70
Part No. 216.93.300
60 correction steel No. 13

for correction angle below(y)
e.g.
Hunger,
D-8000 Munchen 70
Part No. 216.64.622
Data
Inlet
Exhaust
PO50060-13
05.0906 . 291!2
EXIT
Valve distance to cylinder head parting surface

Engines
102.922/924
102.9621963
102.982/985
Minimum distance A with new valve seats and

new valves
Largest distance A with reworked valve seats and
reground valves
Largest distance A reduces by the same dimension, by which the cylinder head parting surface has been reworked.
Note
Clamp cylinder head in clamping fixture for
stripping down and machining.
Machine valve seats with valve seat turning
equipment, with valve seat grinding machine or
with valve seat miller. After machining the valve
seat rings the installation position of the
hydraulic valve clearance compensating
necessary (05214).
05.0906 - 2913
EXIT
Machining valve seats
1
Check valve guide, replace if necessary
(05-285).
2 Machine valve seats (see manufacturers
operating instructions).
Caution!
Only loosen pilot, when eccentricity of valve seat
has been checked (Number 3).
3 Check valve seat eccentricity. For this push

test sleeve (19) with dial gauge bracket (20) and
dial gauge on the pilot (5).
5
18
19
20
Pilot
Dial gauge
Test sleeve
Dial gauge
bracket
4 Measure valve seat width (b), and if required

correct top(P) 15 angle and the bottom (y) 60
angle.
PO&0060-l
05.0906 - 29114
5
Insert valves and measure distance A.
05 0906 - 291i5
EXIT
EXIT
EXIT
emoval and installation of chain tensioner
05-0066-57
V-ribbed belt ..........................

Bolt (49) .............................
Bolt (51)
.............................
Alternator
............................
Sealing plug (40)
.......................
detach, assemble (13-342).

loosen (Number 2).
unbolt (Number 3).
swing outwards.
unbolt.
Note
The sealing plug is under pressure (Number 4).
Sealing ring (41) ........................
Compression spring (39)
..................
Chain tensioner casing (36)

with setbolt (37) ........................
050906-3101
replace.
remove, install.
unbolt (Number 5).
EXIT
Setbolt (37) with locking spring (38)
.........
press out of chain tensioning casing in the

direction of pressure. Check individual parts
for wear (Number 6).
Chain tensioner casing (36) . . . . .
.........
screw into cylinder crankcase, 15 Nm

(Number 7).
Setbolt (37) with locking spring (38)
.........
push in (Number 8).
Sealing plug (40) with compression spring (39)

and new sealing ring (41) . . . . . . . . . . . . . . . . .
screw in, 70 Nm (Number 9).
Alternator
mount (Number 10).
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
\/belt
...............................
assemble (13-342).
When
engine
check for leakage.
is
running
...................
Special tools
Conventional tool
Stud driver insert
17 mm, l/2 square
e.g.
Hazet,
D-5630 Remscheid
Part No. 985/l 7
Note
The housing (36) of valveless, hydraulic lock
chain tensioner is bolted to the crank case (1).
The application force required to tension the
chain is comprised of the force from compression spring (39) and oil pressure in the chain
tensioner, depending on engine oil pressure.
1
41
40
a
39
38
37
36
PO5-0070-
05.0906 - 31012
EXIT
In the event of sudden load the oil feed bore with
1 .l mm 0 (a) and an orifice bore (b) in the
setbolt of 1.2 mm 0 prevents the oil escaping
rapidly and thus has a damping effect. An
embossing is provided in the chain tensioner
casing (36) and a locking spring (38) on the
setbolt.
38
PO52052 -13
36 Chain tensioner casing

37
Setbolt
38
Locking spring
39
Compression spring
40
Cap nut
41
Sealing ring
The locking spring (38) has been modified in

order to improve the function of the chain
tensioner.
38
Changes:
l
l
l
l
37
36
Ends free from burrs

Smaller twist
(dimension a = 0.1 mm, was 0.5 mm)
Improved material
Dimension b = 3.5 mm, was 4.0 mm.
POS-0170-13
Introduced in production: December 1985

Model
201.024 @
050906 - 310/3
Engine
I 102.985
Engine end number

Manual transmission
I 003199
Engine end number

I 029429
EXIT
1
Removal and installation of Poly V- belt
(13-342).
2 Loosen lower bolt (49) for alternator

positioning.
3 Remove upper bolt (51), swing alternator
outwards (arrow).
Unscrew sealing plug (40) and sealing ring

(41) and remove compression spring (39).
Caution!
Sealing plug is pressurized by the compression
spring.
5 Unbolt chain tensioner case (36) from the

cylinder crankcase with the stud driver insert.
6 The chain tensioner must be stripped down

before assembly. To do this press the setbolt
(37) and locking spring (38) out of chain
tensioner casing (36) in the direction of the
arrow. Clean parts and check for wear.
POS-2080-13
05.0906 - 31014
7
Bolt chain tensioner casing (36) onto

crankcase, tightening torque 15 Nm.
8 Push setbolt (37) and locking spring (38) into

the assembled chain tensioner casing.
9 Mount compression spring (39) and sealing

plug (40) with new sealing ring (41), tightening
torque 70 Nm.
10 Mount alternator, tightening torque of the

bolts (49 and 51), 25 Nm.
11 Install Poly V- belt (13-342).
05.0906 - 31015
EXIT
05-320
EXIT
Weplacement of timing chain
Preceding work:
40
#9
0
Spark
41
39
0
0@@@
plugs
Gb
(15)
........................
Chain tensioner (36 to 41)

Chain bolt
. . . . . . . . . . . . . . . .
............................
New timing chain with old timing chain (21) . . . . .

Exterior bracket
Riveting tool
. . . . . . . . . . . . . . . . . . . . . . . .
..........................
Connector link bolt
05 0906 - 320/l
......................
remove, install (15318).

remove and install (05310).
grind off (Number 3).
connect, pull in (Numbers 4 to 7).
press on with riveting tool 000 589 58 43 00,
rivet set 103 589 01 63 00 for single roller
chain, conversion set 000 589 53 43 for double
roller chain (Numbers 8 to 10).
remove, convert (Number 11).
rivet individually (Numbers 12 and 13).
EXIT
Special tools
102 589 01 09OC
000 589 58 43 00
103 589 01 63 OC
Note
An open timing chain with connector link is
supplied for repairs. The sprockets are to be
checked for scores and pitting as well as the
chain tensioner for perfect function before
installing a new timing chain.
Improved timing chains have been installed since

November 1985.
3
2
Changes:
Sleeves (2) with recesses (notches, arrow and
A). f-lence improved oil supply to bolts (3) and
sleeves (2).
A
A
I - i
A
PO5-0165-13
050906
- 32012
EXIT
Introduced in production: November 1985 - May 1986
Model
Engine
Engine end number

Manual transmission
2 0 1 . 0 2 4 @ ( 1 0 2 . 9 8 5 1003057-003893
Engine end number

I 027366-036001
Engine end No.

Automatic
transmission
201.024 @
102.985
I
003925
I
Double roller timing chains have been installed

since January 1988.
05.0906 - 32013
036289
312513
Not recorded
EXIT
The former connector link with locking devices

(A) has been deleted. Only the connector link
(B) is still supplied for riveting.
A
B
Former connecting link with locking

devices
Modified connecting link - can be
rlveted
Replacement
1
Remove, install spark plugs (15018).
Remove, install chain tensioner (05-310).
3 Cover the open part of the chain casing with

a rag, grind off both chain bolts (arrows) at a
double link in the timing chain.
4 Attach new timing chain and the connector

link onto the old timing chain. To do this press
out ground off double link.
5 Put the new timing chain connected with the

old timing chain onto the camshaft timing gear.
Rotate crankshaft.
Caution!
The timing chain must remain engaged while
rotating the camshaft timing gear.
05.0906 - 320/4
POS-2057-13
EXIT
6 Pull out the released end of the old timing

chain evenly, to correspond with drawing on the
new timing chain.
Caution!
The timing chain must remain engaged while
turning the camshaft timing gear and crankshaft
gear.
Secure the ends of the chain to the

camshaft timing gear with wire. Detach old
timing chain and connect the ends of the new
timing chain with the repair connector link.
7
Note
Connector link must be inserted from behind.
8 Fit riveting set 103 589 01 63 00 to the basic

tool 000 589 43 00 corresponding to the timing
chain design (single or double roller chain).
9 Put loosely attached exterior bracket of the
connector link in the press tool (arrow).
The exterior bracket is held magnetically.
POS-2053-13
10 Put press tool on the connector link and

press on bracket up to the stop.
Note
Put on clip so that both rivet pins engage.
05.0906 - 320/5
EXIT
11 Remove assembly tool and turn punch (02)

so that the notch (arrow) points forward.
PO!%2056-13
12 Install assembly tool exactly over the center

bolt. Rivet bolts of the connector links
individually, tightening up spindle to approx. 30 35 Nm (reference value).
13 Check riveting (arrows), re-rivet if required.
14 Install chain tensioner (05310).
05 0906 - 32016
15 Turn crankshaft and check adjustment
markings at engine TDC position.
Note
If the adjustment markings do not align, the valve
timing settings of the camshaft must be checked
(05215).
16 Assembly is completed in the reverse order.
0 5 . 0 9 0 6 - 32017
EXIT
05328
Installation of oil spray nozzle retroactively
Preceding work:
Timing case cover removed(01-210).
idler gear shaft removed (05-412).
POS-0076-35
Sealing plug (13)
. . . . . . . . . . . . . . . . . . . . . . .
..........................
Joggle plate
Oil spray nozzle (66b and 66~).
.............
remove (Numbers 1 and 2).

Part No. 102 589 14 15 00 bolt up, unbolt
(Number 3).
drive home up to stop (Number 4).
Idler gear shaft .........................
install (05-412).
......................
install (01-210).
Timing case cover

On engine
............................
When engine is running
Special tools
05.0906 - 3281'1
..................
change oil and filter.

check for leaks.
EXIT
Note
In order to achieve better lubrication of the
timing chain, an additional oil spray nozzle (66)
has been fitted in the front face of the main oil
channel. This oil spray nozzle, can be installed
retroactively. The retroactive installation should
only be carried out, when for example the timing
case cover has already been removed for other
work.
Production breakpoint of the various designs

Injection engines
66a 1st design March to April and May 1986
66b 2nd design November 1986 to July 1987
66c 3rd design July 1987
05.0906 - 328.2
EXIT
............................................................................................
... ...
....
....... . .
EXIT
Production breakpoint: March - April 1986

(Injection engines 1st design)
2 0 1 . 0 2 4 @ 1 1 0 2 . 9 8 5 1003626-003670
I 033140-033543
Production breakpoint: May 1986

(Injection engines 1 st design)
201.024 @
1 102.985 I00381 l-003828
I 03521 o-035424
Production breakpoint: November 1986

(Injection engines 2nd Design)
I Engine
Model
201.028
102.985
I Engine end No. Man. transm.
I Engine end No. Autom. transm.
I 007099
I 045782
Production breakpoint: July 1987

(Injection engines 3rd Design)
201.028
05.0906 - 32813
I 102.985
I 015733
I 057671
EXIT
Installation
1
Remove sealing plug (13), to do this drill a
core hole (5 mm 0, 10 mm deep).
Note
Carefully cover oil channel (a), bearing bore (A)
and window (arrow).
2 Unscrew sealing plug with impact extractor
116 589 20 33 00 and stud 116 589 00 34 00
3 Attach joggle plate (AP) 102 589 14 15 00

with two hexagon bolts M8 x 15 (48).
4 8
5 0
P18-0009.13
Cylinder crankcase
Fixing bolts
50 Straight pin (guide for timing case cover)
66 011 spray nozzle
AP JOQQle plate
48
05.0906 - 32814
EXIT
4 Select correct oil spray nozzle (carburettor
or injection engine) and drive home the cylinder
crankcase up to the stop. The correct fitting
position of the oil spray nozzle is achieved when
this is laid on the joggle plate, as shown in
Figure (Number 3).
I Carburettor
engines (non-US)
2 Injection engines
POS-0013.13
5 Detach joggle plate.

6
Install idler gear shaft (05412).
Install timing case cover (01-210).
Change engine oil and filter.
Check for leaks when engine is running.
Parts required
Part No.
Oil spray nozzle
102 180 09 43 (Carburettor engine)

102 180 08 43 (Injection engine)
Standard Text and flat rates

Install oil spray nozzle for timing chain
(Idler gear shaft removed)
The operation number
050906 - 328/5
IS t
o
02-0367/01
be placed in front of the book/column number.
Related work, 5 flat rates or 0.4 hours
EXIT
EXIT
emoval and installation of tensioner blade

Preceding work:
Timing case cover removed (01-210).
PO5-0071-35
Timing chain (21) and crankshaft gear
. . . . . . . .
Timing chain and camshaft timing gear (4)

. . . . .
. . . . . . . . . . . . . . . .
...................
mark (Number 1).

mark (Number 2).
unbolt, bolt up, put to one side with lines
Camshaft timing gear (4) ..................
unbolt, bolt up, 80 Nm (Number 5).
Tensioner blade (22) .....................
remove from bearing bolt, put on.
Note
On double roller chain, spot drill bearing pin (26)
and drive out with the impact extractor 115 589
12 33 00. Install new tensioner blade with
bearing pin (Numbers 7 and 9).
Plastic support (23) .
....................
check, possibly renew (Number 8).
Camshaft adjustment
....................
check (Number 11).
05.0906 - 330/l
Special tools
001 589 72 21 00
116 589 03 34 00
Note
In order to achieve better guidance of the timing
chain, the plastic support has lateral guide bars

(arrows). The plastic support is also fixed
differently; in this way the support is prevented
from slipping off the tensioner blade.
A Former design
B Current design
Production breakooint: Auaust 1986

Model
Engine
Engine end No.

Engine end No.
Man. transmission Auto. transmission
325157
05.0906 - 33012
EXIT
EXIT
1
Align timing chain and crankshaft gear.
-2
B
2
Align timing chain and camshaft timing gear.
Remove chain tensioner (05-310).
4 Unbolt oil pressure pump with lines

connected (arrows) and put to one side.
05.0906 - 330~3
Pck5-2056-13
EXIT
5 Unbolt, bolt up camshaft timing gear, bolt
(9a), tightening torque 80 Nm. Note color
markings on camshaft timing gear and crankshaft
gear.
Note
On vehicles with oil pressure pump remove
driving disc sleeve (70).
6 Swing tensioner blade (22) for single roller

chain inwards and remove from bearing pin (26),
install.
7 On engines with double roller chain, drive

out bearing pin (26) of the tensioner blade with
the impact extractor 116 589 20 33 00 and
extension 116 589 03 34 00. To do this cut an
M6 thread approx. 10 mm deep on the bearing
pin. Remove tensioner blade.
8 Check plastic support for wear, replace if

necessary.
PO5-2032-13
05.0906 - 330/4
9 Insert new tensioner blade and drive home
bearing pin up to stop.

11 Turn crankshaft and check adjusting marking
at TDC position of engine.
12 The installation proceeds in the reverse
sequenceas removal.
13 Run engine, check for leaks.
05.0906 - 3306
EXIT
..................
EXIT
......
05340
Removal and installation of guide rails
A. Guide rail (24) in cylinder heacd
Preceding work:
Cylinder head cover removed(01-460).
PO5-0078-57
................
Fan shroud (1) and fan (75)
...............
050906
- 340/l
..................
remove, install 70 Nm (Number 1).

remove, install, bolt (80), 25 Nm (Number 2).
Oil
pressure
pump
(69)
...................

align and unbolt, bolt (9 and 9a), 80 Nm

(Number 5).
Guide rail bolt (26)
. . . . . . . . . . . . . . . .
extract, with impact extractor 116 589 20 33 00

and stud 100 589 00 34 00, drive home
Note
Insert guide rail bolt with sealant
001 989 25 20. Note that the fixing nose on the
guide rail engages in the guide rail bolt
(Numbers 6 and 7).
When
running
check for leaks.
engine
is
.............
Special tools
116589203300
001 589 72 21 00
05.0906 - 34012
100 58900 34 00
001 589 66 21 OC
EXIT
EXIT
Note
The guide rails have been changed with the
introduction of the double roller chain.
A Guide rail for single roller chain

B Guide rail for double roller chain
POS-0079-13

1
Removal and installation of chain tensioner
(05310). Tightening torque of hexagon cap nut
(40) 70 Nm.
2 Remove fan shroud (1) and fan (75).

Tightening torque of bolt (80) 25 Nm.
P20-0006-13
3 Position piston of No. 1 cylinder on ignition

-l-DC.
05.0906 - 34013
4 Unbolt oil pressure pump with lines
connected (arrows) and set to one side.
5 Align timing chain and camshaft timing gear.

Unbolt camshaft timing gear and remove
sprocket.
Note
When installing the sprocket note color
markings. Tightening torque of set bolt
80 Nm.
6 Withdraw both guide rail bolts (26) with

impact extractor 116 589 20 33 00 and stud
100 589 00 34 00.
Note
If the guide rail bolts are too tight, the extractor
115 589 20 33 00 with stud
115 589 00 34 00 can also be used.
Impact extractor in place
050906 - 340!4
EXIT
7 Install guide rail (24) so that the locating lug
(arrow) engages in the groove of the upper guide
rail bolt.
Note
Apply sealant 001 989 25 20 at collar of guide
rail bolts.
8
Check for leaks when engine is running.
05.0906 - 340/5
EXIT
EXIT
.
Guide rail in cylinder crankcase
Preceding work:
Timing case cover removed(01-210).
PO5-0080-57
a. With single roller chain

Guide rail (25a, single roller chain) . . . . . . . . . . .
remove, put on (Number 1).
b. With double roller chain

Oil
pressure
Chain tensioner
05 0906 - 340/6
pump
. . . . . . . . . . . . . . . . . .
(69)
...................
. . . . . . . . . . . . . . . . . . . . . . . .

. . . . .
EXIT
align and unbolt, (9 and 9a), 80 Nm (Number 5).
Timing chain and crankshaft gear . . . . . . . . . . . .
align (Number 6).
Bolt (20)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
unscrew, remove clip (19) and idler gear shaft

(18) (Numbers 7 and 8).
. . . . . . . . . . .
pull forward as far as possible, remove and fit

guide rail (25b) (Number 9).
Timing chain with crankshaft gear
Note
When pushing back the crankshaft gear, and
the timing chain, note the positioning pin in the
camshaft flange and alignment of timing chain to
tension lever.
Idler gear shaft (18)
. . . . . . . . . . . . . . . . . . . . .
Further installation
. . . . . . . . . . . . . . . . . . . . . .
Special tool
1 001 589 66 21 00
05.0906 . 34017
. . . . . . . . . . . . . . . . . .
install, bolt (20), 5 Nm (Number 10).

in reverse sequence.
check for leaks.
EXIT
Note
The guide rails have changed with the
introduction of the double roller chain.
A Guide rail for single roller chain

B Guide rarl for double roller chain
POS-0075-13

a. With single roller chain
1
Pull off guide rail (23, install.
b. With double roller chain

2 Position piston of No. 1 cylinder on ignition
TDC.
3
Unbolt, bolt up oil pressure pump (arrows)
and put to one side with lines connected.
05 0906 - 340/8
4
EXIT
Remove chain tensioner (05310).
5 Align timing chain and camshaft timing gear

and unbolt camshaft timing gear. Put timing
chain in timing case.
Align timing chain and crankshaft gear.
Po5-2056-13
7 Unscrew bolt (20) and remove retaining

clip (19).
05.0906 - 340/9
EXIT
8 Pull out idler gear shaft (18) and remove
timing chain.
POS-2085-13
9 Remove, install, pull timing chain and

crankshaft gear forward as far as possible and
remove guide rail (25b). Put on timing chain and
push back crankshaft gear together with timing
chain.
Note
When pushing back the crankshaft gear, note
the positioning pin in the camshaft timing gear
flange and the color marking.
10 Install idler gear shaft, tightening torque of

the hexagonal socket screw (20) 5 Nm
(reference value).
PO5-2085-13
05.0906 - 340/10
11 Install timing chain and camshaft timing gear,
note marking. Tightening torque of camshaft
timing gear set bolt 80 Nm.
12 Install chain tensioner (05310). Tightening

torque of sealing plug (40), 70 Nm.
13 Check adjustment marking of camshaft
(arrow) at ignition TDC position of engine,

correct if necessary.
14 Install oil pressure pump, in so doing note

driving disc.
15 The installation is the reverse of removal.
05.0906 - 34Ot'll
EXIT
EXIT
emoval and installation of idler gear shaft

Preceding work:
Timing case cover removed (01-210).
Fuel pump removed (07.2-212, only carburettor engines).
PO5-0080-57
................

Oil
pressure
pump
(69)
...................
remove, install (05-310).

unbolt, bolt up, set to one side with lines
..................
align with timing chain (Number 3).
Crankshaft gear
. . . . . . . . . . . . . . . . . . . . . . . .
align with timing chain (Number 4).
Bolt (9 and 9a)
. . . . . . . . . . . . . . . . . . . . . . . .
unbolt, bolt up and remove camshaft timing

gear, 80 Nm. Note marking (Number 5).
Guide rail (25a)
. . . . . . . . . . . . . . . . . . . . . . . .
remove, install (only on single roller chain,

Number 6).
Camshaft
timing
05.0906 - 412/l
gear
(4)
EXIT
Hexagon
socket
Idler gear shaft (18)
bolt
(20)
..................
. . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . .
unbolt, bolt up, 5 Nm. Remove, install retaining

clip (19) (Number 7).
withdraw from rear bearing and remove from
timing chain, insert (Numbers 8 and 9).
check for leaks.
Special tool
I 001 589 66 21 O(
Note
The idler gear (18b) is pressed on the idler gear
shaft (18) supported on bearings in timing case
cover and cylinder crankcase. It is fixed axially
by a retaining clip (19) bolted on the cylinder
crankcase, which engages in a groove on the
idler gear shaft. The teeth for driving the ignition
distributor (18~) are located behind the front
bearing position.
Arrangement of idler gear shaft

Engines 102.985
6
I Cylinder crankcase
6 Beanng bush in timing case cover
17 Bearing bush In cylinder crankcase
18 Idler gear shaft
18b Idler gear
18c Teeth for ignition distnbutor drive
19 Retaining clip
20 Bolt M5x18 mm
44 Timing case cover
05.0906 - 41212
17
PO50090-13
EXIT

1
Remove chain tensioner (05-310).
2
Unbolt, bolt up oil pressure pump (arrows)
and put to one side with lines connected.
Align camshaft timing gear and timing chain.
Align crankshaft gear and timing chain.
5 Unbolt camshaft timing gear and remove, put

timing chain in timing case.
PO3-2056-13
05.0906 - 41213
6 Remove guide rail (25a) (only on single roller
chain).
7
Unbolt hexagon socket bolt (20) and remove
retaining clip (19).
8 Remove idler gear shaft (18), install, in so

doing raise timing chain somewhat.
9 Install retaining clip (19) and secure with bolt
(20) tightening torque 5 Nm (reference value).
10 Install guide rail (25a).

11 Assemble camshaft timing gear, at the same
time noting colored markings, tightening torque
80 Nm.
12 Check adjustment marking of the camshaft

(arrow) at ignition TDC position of engine,
correct if necessary.

14 The installation is the reverse of removal.
05.0906 - 412'4
EXIT
EXIT
emoval and installation of oil pressure pump drive

Preceding work:
Set
bolts
(68)
. . . . . . , . . . . . . . . . . , . . . . . . . .
unbolt, bolt up, 15 Nm (Numbers 1 and 2).
. . . . . . . . . . . . . . . . . . .
remove together with driving disc (76). On

Model 201 set oil pressure pump with lines
connected to one side.
Gasket (75)
...........................
Driving disc (76) ........................
renew.
remove, install.
Flange (71)
...........................
unbolt, bolt up, with attachment eye (22), 25 Nm

(Number 4).
O-Ring (73)
...........................
replace.
Hexagon socket bolt (9a) ..................
05.0906 - 43711
unbolt, bolt up, 80 Nm. Remove, install driving

disc sleeve (70) (Number 5).
Special tools
001 589 66 21 00
001 589 72 21 OC
69
I Camshaft
Camshaft timing gear
6 Woodruff key
9a Hexagon socket bolt
21 Timing chain
69 Oil pressure pump
70 Driving disc sleeve
71 Flange
4
73
O-Ring
Gasket
Driving disc
81 Cylinder head cover
93 Cylinder head cover
gasket
75
76
Note
The oil pressure pump (69) is driven directly by
the camshaft (1) via the driving disc sleeve (70)
and the driving disc (76) and is attached to the
cylinder head by a flange (71). The fitting
position of the flange on the cylinder head is
fixed by two straight pins (arrows). The camshaft timing gear (4) is attached to the camshaft
with the driving disc sleeve (70) and the hexagon
socket screw (9a). The O-Ring (73) on the
flange (71) seals the front semicircular bore in
the cylinder head and in the cylinder head cover
(61).
05.0906 - 43712
75
93
21
81
EXIT
.................................................
...................
EXIT

1 On Model 201 remove bolts (68), remove oil
pressure pump and set to one side with lines
connected.
Model 201
2
Remove, install driver (76).
Replace gasket (75).
75
69
PO5-0081-13
3
Unbolt, bolt up flange (71) together with the
attachment eye (22), renew O-Ring (73).
Tightening torque of bolts (72) 25 Nm. Note
both dowels (70).
POS-0083-13
05.0906 - 43713
4 Unscrew hexagon socket bolt (9a) and
remove, insert driver sleeve (70), tightening
torque 80 Nm.
70
9a
I
6P
05.0906 - 43714
@a
EXIT

Mercedes 190e

Uploaded by

Document Informationclick to expand document information

Copyright:

Available Formats

Mercedes 190e

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Mercedes 190e

Uploaded by

Copyright:

Available Formats

www.WorkshopManuals.co.

ngine timing, valvetrain 05

ngine timing, valvetrain

Checking and replacement of hydraulic valve clearance

position hydraulic element under test on the

Fill up reservoir chamber of valve clearance

With oil reservoir chamber full and original

Install (05-235), at the same time fit original ball

Valve clearance compensating element (58)

Rocker arm bearing support (61)

Hydraulic valve clearance compensation

Valve adjustment Is no longer required when

Set bolt (64) with oil reservoir chamber (a)

Guide sleeve (59) with working chamber (b),

The element can drop completely when the

The oil needed for operating the hydraulic valve

In order that the hydraulic valve clearance

The sealing cap (65) is shaped so that it secures

If one compensating element drops noticeably

If a leaking compensating element cannot be

3 Fill reservoir chamber of the hydraulic valve

If compensating element does not drop

5 Install rocker arm bearing support (05235).

6 Check the installation position of the new

Install in the reverse sequence.

Checking and correcting the installation position of hydraulic valve

position the cylinder under test so that rocker

Turn pressure pad (06) to the right until a

Remove and install rocker arm bearing support

Adjusting the residual stroke

Install, repeat test (Numbers 7 and 8). Prior to

Mahr, D-7300 Esslingen

The tests can also be carried out when the

3 Insert measuring pin adapter (04) in the

4 Turn pressure pad (06) slowly to the right

If specified residual stroke cannot be achieved

The grooves in the washer (57) must point in the

Install rocker arm bearing support (05-235).

8 Repeat tests, Numbers 1 to 3.

Checking and ad)usting camsbft timing

Position the No. 1 cylinder camshaft so that the

Insert and put tip vertically on valve spring

Put engine on ignition TDC of No.1 cylinder

Unbolt and bolt up, replace sealing ring

Oil pressure pump . . . . . . . . * . . .

Unbolt, set to one side with lines connected

Camshaft timing gear . . . * . . . . . .

Align with timing chain.

Select from table and insert (Numbers

Camshaft timing gear .

Assemble, note color marking, only install set

Chain tensioner locknut (40)

Woodruff key (6)

Dial gauge (01) and dial gauge (02)

Rocker arm bearing support and rocker arm with

Value for used c WI In brackets.

Mahr, D-7300 Esslingen