Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd
Upload
190 views

ACI Method Example

This document provides an example of an American Concrete Institute (ACI) absolute volume mix design for a non-air entrained concrete batch. The mix design calls for a 30 kg batch with a water-cement ratio of 0.5 and slump of 80-100 mm. Following ACI standards, the document calculates the volumes and masses of cement, water, fine aggregate, coarse aggregate, and air needed to achieve the desired mix properties in 1 cubic meter of concrete. The final step scales the 1 cubic meter design proportions down to a 30 kg batch size.

Uploaded by

Sam Ang Keo
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
190 views

ACI Method Example

This document provides an example of an American Concrete Institute (ACI) absolute volume mix design for a non-air entrained concrete batch. The mix design calls for a 30 kg batch with a water-cement ratio of 0.5 and slump of 80-100 mm. Following ACI standards, the document calculates the volumes and masses of cement, water, fine aggregate, coarse aggregate, and air needed to achieve the desired mix properties in 1 cubic meter of concrete. The final step scales the 1 cubic meter design proportions down to a 30 kg batch size.

Uploaded by

Sam Ang Keo
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

EA102

American Concrete Association (ACI) Absolute Volume Method of Concrete Mix Design

EXAMPLE ACI MIX DESIGN


Mix Component Properties:

Cement

Coarse Aggregate

Fine Aggregate

Type: 10
Specific Gravity: 3.155
Nominal Maximum Particle Size:
SSD Bulk Specific Gravity:
% Absorption Capacity:
Dry-Rodded Density:

10 mm
2.660
3.50%
1.530 Mg/m3

SSD Bulk Specific Gravity: 2.700


% Absorption Capacity: 1.50%
Fineness Modulus: 2.700

Desired Mix Properties:


A 30 kg batch on non-air-entrained concrete with a slump in the 80 to 100 mm range and a
water/cement ratio of 0.5 is required.
SOLUTION:
1. Determine densities of all materials to be used: = G x w
Specific
Material
x w =
Gravity
Water
1.0
x 1000 =
Cement
3.155
x 1000 =
SSD Fine Aggregate
2.700
x 1000 =
SSD Coarse Aggregate
2.660
x 1000 =
Dry-Rodded Coarse Aggregate
2.

Mass of mixing water in 1 m3 of mix = 228 kg = 0.228 m3

Density (kg/m3)
1000
3155
2700
2660
1530

(Table 4a for non-air-entrained, Nominal Maximum size = 10mm and slump between 80 & 100 mm)

3. Volume of air in 1 m3 of mix is 3.00% of 1 m3 or 0.030 m3


(Table 4c for non-air-entrained, Nominal Maximum size = 10mm)

4.

228 kg
w
w
0.5, then c

456 kg The mass of cement required = 456 kg


c
0.5
0.5
456 kg
The volume of cement
The volume of cement required = 0.145 m3
3
3155 kg/m
If

5. Volume of dry-rodded coarse aggregate = 0.47 m3

(Table 3 for Nominal Maximum size = 10 mm and fineness modulus of 2.70)

6. SSD mass of coarse aggregate = 0.47 m3 x 1530 kg/m3 = 719 kg


SSD volume of coarse aggregate

719 kg
2660 kg/m 3

= 0.270 m3

7. Sum of known volumes = (0.228 + 0.030 + 0.145 + 0.270) m3 = 0.673 m3


SSD volume of fine aggregate = 1 0.673 m3 = 0.327 m3
SSD mass of fine aggregate = 0.327 m3 x 2700 kg/m3 = 883 kg
8. Total mass of 1 m3 of mix = (228 + 456 + 719 + 883) kg = 2286 kg/m3
The proportioning factor

2286 kg
30 kg

= 76.2

Each mass for the 1 m3 of mix is then divided by this factor:


Mass
(kg/m3)

Volume
(m3)

SSD Mix Masses


(kg)

Cement
Water
Coarse Aggregate
Fine Aggregate
Air

456
228
719
883

0.145
0.228
0.270
0.327
0.030

5.984
2.992
9.436
11.588

Totals

2286

1.000

30.000

Materials

NOTE: The information in this table should appear in the table on Datasheet 7.5.
Do not present it twice!

You might also like