Professional Documents
Culture Documents
Ericsson Parameter1
Ericsson Parameter1
Parameter
Description
Range
BSPWRB
0 -> 63 dbm
Ericsson
Dafault
Value
SingTel
Recommended
Value
45
45 dBm
Remarks
Note that RBS2301 and 2302 only can supports till 33dbm
900: 31
GSM 1800:
33toto47dbm
45dbmInInodd
odd
values only
BSPWRT
0 -> 63 dbm
45
Note that RBS2301 and 2302 only can supports till 33dbm
BSIC
BCCHNO
BCCHTYPE
MCC : 3 digits
LAC: 1 to 65535
CI - Cell Identity
CI : 0 to 65535
NCC: 0 to 7
BCC: 0 to 7
0 to 7
1 to 124( GSM900)
NCOMB
NCOMB
Type of BCCH
1) COMB - indicates that the cell has a combined
BCCH
and SDCCH/4
2) COMBC
- indicates that the cell has a
The BCCH is always allocated to time slot number 0 in the defined ARFCN
AGBLK
0 to 7 if non-combined Bcch is
used
1 AGBLK
5 CCCH
MFRMS
FNOFFSET
ECSC
0 TDMA Frame
Yes
YES
To prevent that all cells on a site send BCCH channels at the same time it is possible
to define a deviation with respect to the FN generator called FNOFFSET. By using
FNOFFSET on a synchronised two or three sector site the time for decoding BSIC
can be reduced. RBS2000 and 200 only support the range 0 to 1023.
The parameter ECSC has to be set to YES in order to allow the MS to send the
MS mutliband and/or multislot capability.
TSC
0 to 7
Same as BCC
1,4,7
MSTXPWR
33
33 dBm
30
30 dBm
ACTIVE
TCH
TCH
STATE
ACTIVE, HALTED
HOP
0 to 63
system
1 to 63
defined
DCHNO
1 to 124( GSM900)
SDCCH
TN
SYSDEF
16 to 96 range
32 ARFCN
0 to 16
1 sdcch
0 to 3 (normal cell). 0, 2
(extended range cell).
1st TimeSlot
CBCH
Yes, No
No
NO
SCHO
ON, OFF
OFF
OFF
ON - handovers on SDCCH are allowed; OFF - handovers on SDCCH are not allowed
DTXD
ON, OFF
OFF
OFF
Note: ON: DTX DL is enabled for the cell; OFF: DTX DL is disabled for the cell
DTXU
0 to 2
TN is only valid for CCHPOS = TN and must be equal for all channel groups in a cell.
to save batteries
0 to 15 or DEFAULT
FHOP
Frequency Hopping
BB, SY
DEFAULT
BB
DEFAULT
SingTel using Baseband Hopping for GSM900 System, RF Hopping for GSM1800
CHGR
SCTYPE
CELL DATA
HCSBAND Layer
LAYER
LAYERTHR
UL, OL
1 to 8
1 /2
75
75 dBm / 95 dBm
0 to 63db
2 dB
PSSTEMP
0 to 63db
0 dB
PTIMTEMP
0 to 600 seconds
ON, OFF
CSYSTYPE
MBCR
Specifies
system
type -for
the cell
Multi Bandthe
Cells
Reported
defines
the nos of
neighbours from each frequency band that shall
be
0 to 3
0 second
OFF
OFF
GSM900
GSM900
0 or 1
The HCS feature with 3 layers allows building a network in a two- or three-layered
structure. The higher layers can for example be used for large cells and the lower for
small cells. Cells in layer 1 have higher priority than cells in layer 2, which in turn have
higher priority than cells in layer 3.
CCHPWR
47 to 110 dBm
- 110 dBm
- 104 dBm
A low value of ACCMIN means that the coverage in idle mode is improved at the
expense of the risk of having an increased number of call setup failures
CRH
13 to 43 (GSM900)
33
33 dBm
4 to 30 (GSM1800)
30
30 dBm
4 dB
1, 4, 6
1,4,6
No
No
HIGH
HIGH
0 dB / 4 = 8 dB
0 to 14 in steps of 2db
0 to 7
Yes, No
CBQ
HIGH, LOW
CRO
0 to 63 [0 dB to 126 dB in steps
of 2 dB)
0 to 7 [0 dB to infinite dB in
steps of 10 dB]
0 dB
PT
0 / 31
T3212
40
20 = 2 hours
DOUBLE BA List
MBCCHNO
LISTTYPE
1 to 124 (GSM900)
MBCCHNO is the BCCH allocation, i.e. it indicates to the MS the frequencies that
must be monitored and measured in idle, active or both modes.Up to 32 BCCH carriers
32 BCCH in the List can be defined by specifying their ARFCN
IDLE/ ACTIVE
16
16
RLINKUP is used by the BSC to determine when to disconnect the call upon
repeated failure in decoding the SACCH.
16
63
NO
NO
Extended range
RLINKUP
RINKT
MAXTA
XRANGE
8 to 64 in steps of 4 SACCH
periods (480ms)
0 to 63 (normal cell)
YES, NO
16
63
1 to 9
QEVALSD
1 to 9
SSVALSI
1 to 9
9 Median filter
QEVALSI
1 to 9
SSLENSD
1 to 20 SACCH periods
QLENSD
1 to 20 SACCH periods
SSLENSI
QLENSI
SSRAMPSD
Length
quality
filter strength
for signalling
Rampingof
length
of signal
for only
speech/data
SSRAMPSI
10
12
12
10
12
12
1 to 20 SACCH periods
1 to 20 SACCH periods
0 to 18
1 to 20 SACCH periods
BSTXPWR
50
50 dBm
BSPWR
50
50 dBm
MSRXMIN
100
100 dBm
0 to 80 dbm
BSRXMIN
116
116 dBm
0 to 150 dbm
0 dBm
0 to 150 dbm
max 150
150 dBm
OFF
ON
ON
ON
NOPREF
NOPREF
BSRXSUFF
AW
ON, OFF
FPDCH
0 to 8
note: NOPREF: the channel alocation algorithm should not consider this parameter
FIRST When allocating the first dedicated PDCH it must be allocated on the nonhopping BCCH frequency. If no channels are available on the non-hopping BCCH
frequency on-demand channels are allocated instead, until the requirement is fulfilled.
CHCODING
CS 1 or 2 for Ericsson R8
PILTIMER
1 to3600.
GPRSPRIO
0,16,24
CS 2
CS 2
20 seconds
20 seconds
0 or 1
INACTIVE
ACTIVE
95 dBm
ACTIVE, INACTIVE
SSDES
47 to 110 dbm
85
INIDES
47 to 110 dbm
70
85 dBm
5 SACCH
2 SACCH
70
30%
SSLEN
LCOMPUL
PMARG
QDESUL
0 to 70 dtqu
QLEN
1 to 20 SACCH periods
INILEN
3 dB
20
35 dtqu
12 SACCH
QCOMPUL
0 to 60 %
30
30%
MS power regulation is performed at intervals specified by REGINT. A new power
order is issued only if the calculated power level is different from the current MS
power level.
REGINT
1 to 30 SACCH periods
3 SACCH
DTXFUL
5 SACCH
INACTIVE
ACTIVE
OFF
OFF
ACTIVE, INACTIVE
SDCCHREG
ON, OFF
SSDESDL
47 to 110 dbm
70
90 dBm
REGINTDL
1 to 10 SACCH periods
1 SACCH
SSLENDL
3 to 15 SACCH periods
4 SACCH
LCOMPDL
0 to 100 %
70
20%
QDESDL
0 to 70 dtqu
20
0 dtqu
QCOMPDL
0 to 60 %
30%
60%
QLENDL
1 to 20 SACCH periods
5 SACCH
BSPWRMIN
20
20 dB
62
61
10 dB
10 dB
PSSBQ
0 to 63 db
PSSTA
63
63 dB
PTIMBQ
0 to 600 seconds
10
15 sec
PTIMTA
0 to 600 seconds
10
10 sec
QLIMDL
0 to 100 dtqu
55
55 dtpu
QLIMUL
0 to 100 dtqu
55
55 dtpu
63 dB
63 dB
15
15
TALIM
Handover Failure
PSSHF
0 to 63 db
PTIMHF
0 to 600 seconds
ON, OFF
TMAXIHO
0 to 60 seconds
OFF
OFF
6 seconds
TIHO
0 to 60 seconds
10
5 seconds
MAXIHO
0 to 15
10
10
10
-30 to +30 db
-30 to +30 db
ACTIVE: The measurements made are used for statistical purposes and at channel
allocation.
PASSIVE: No idle channel measurements are made.
NOALLOC: The measurements are used for statistical purposes only.
ICMSTATE
PASSIVE
ACTIVE
INTAVE
6 SACCH
LIMITn
LIMIT1 = 0 to 59
LIMIT2 = 1 to 60
LIMIT3 = 2 to 61
12
12
Band 3 : - 98 dBm
LIMIT4 = 3 to 62
22
25
Band 4 : - 85 dBm
INACTIVE
ACTIVE
ACTIVE, INACTIVE
CLSACC
1 to 100 %
40%
40%
0 to 99 %
20%
20%
ON, OFF
OFF
ON
75%
75%
5 seconds
CLSLEVEL
RHYST
CLSRAMP
0 to 30 seconds
1 to 7 Characters
The interval during which value of RHYST is ramped up from zero to the final value.
KHYST
0 to 63db
3 dB
3 dB
LHYST
0 to 63db
3 dB
3 dB
TRHYST
KOFFSET
LOFFSET
TROFFSET
BQOFFSET
CAND
Candidate Type
-63 to 63 db
2 dB
3 dB
3 dB
-63 to 63 db
0 dB
-63 to 63 db
0 dB
0 to 63db
63 dB
3 dB
BOTH
BOTH
3 dB
0 to 63 db
Ericsson 3
HIHYST
0 to 63 db
5 dB
5 dB
LOHYST
0 to 63 db
3 dB
3 dB
HYSTSEP
0 to 150 dbm
90 dBm
90 dBm
OFFSET
-63 to 63 db
3 dB