Natural Horse Supply

Tie Your Own Simple Rope Halter

Making your own rope halters is a rewarding process. You get an extra feeling of
accomplishment knowing that your horse is responding to something personally made with
your own hands. The first time that you attempt to make a halter, you may spend a few
hours tying and untying the knots, studying the instructions, and thinking about all the
money you are saving making your own tack! Dont get discouraged if you make mistakes
or have to start over from the beginning -- each successive rope halter that you make will be
a little bit easier, until you have it down to a 10 minute process!
These are not the same techniques that we use to manufacture our Natural Horse Supply
rope halters. These are instructions for a simple rope halter that can easily be made by the average person. Our Natural
Horse Supply rope halters use a Fiador knot for lead rope attachment and double overhand (Blood) knots. In addition, the
latch knot end ropes are spliced and sewn to prevent unraveling. Well teach you how to make a simple, very durable and safe
rope halter that you can use to train your horse.

Materials List:

Size of Horse

Amount of Rope Needed

Small Pony
18 Feet
Depending on the size of
Medium

Arab
20
Feet
your horse, these are the
Large

Horse
22
Feet
materials you need:
Extra Large - Warmblood 24 Feet
Extra Extra Large - Draft 26-28 Feet
We use nylon double braided nylon. This is an ideal choice because it has a braided nylon sleeve over a braided nylon
core which makes for a very soft rope. You can find this type of rope at a marine supply store or mail order it from many
sources. This rope is much more expensive than other ropes that youll find in the hardware store, but there is definitely a
difference in quality. Nylon double braid also has a tensile breaking strength of 2,300 pounds per square inch (PSI), making
it extremely durable. Many people use or 3/8 nylon or polyester rope to make halters it really comes down to a personal
preference. And, you may just have to use what you have available.
Youll also need a sharp knife or single edge (safety) razor blade to trim the ends of the rope and a lighter or matches to
melt/seal the ends of the rope when finished.

Knots

Even a good Cub Scout knows a thing or two about knots. Fortunately, you dont need to master too many in order to make a
rope halter. You may want to practice these knots before you start making your halter to lessen the frustration level

The Overhand Knot

This rope halter relies on an overhand knot as the basis for making your halter. This is what an
overhand knot looks like. If you can tie your shoes then you can tie this knot! Tying the overhand
knot is simple, the hard part is tying into this knot to create a double overhand or blood knot.

The Double Overhand Knot

The double overhand knot is tied by threading the end of the rope through an existing overhand
knot and back around to form a double knot. This is an attractive and durable knot which is
extremely difficult to take apart once it has been used on a horse. Its also difficult to learn to tie

because you come at it from different directions on a rope halter. This knot takes some time to perfect, but is ideal for the
rope halter because there is not flat portion of the knot.
Tying the Double Overhand Knot

Step 1: Loosen the existing overhand knot and feed the loose end of the rope through the middle of
the existing knot. Make sure that the rope goes into the center loop of the existing knot on the
same side of the loop as the rope on the first overhand knot.
Step 2: Take the end of the rope over the top of the overhand knot, crossing directly in the groove
or V of the knot and back behind the two strands of rope. I find it easier to turn the existing double
overhand knot to the side at about a 45 degree angle this makes it easier for the next step.
Step 3: Bring the end of the rope around and through the middle of the overhand knot. Take the
rope through the new overhand, tighten the rope and take up the slack. Turn the knot over and
youll have a wonderful double overhand knot!
TIP: Knots for the Knot Challenged

For those of you who are having a hard time getting the double overhand knot to work out, you can
simply tie into the knot following the path of the rope through the existing overhand knot. This is
not as effective for training because it lays flat on the horse. Also, not as pretty as the double
overhand -- but its not very hard to tie either It works!
Making the Halter

This type of halter requires that you tie the overhand knot at the correct location on the rope. The distances are measured
from knot to knot and do not include the knot in the measurement. Its important not to tie these knots too tight at first
because you are going to go back to tie into the existing overhand knots to finish the halter.
Step 1: Determine the size of halter you want to make. Take a measurement around your horse's nose just below the cheek
bone. Note: the average horse is about 24" around the nose. Use a string to get the length of these measurements and lay the
string out against a yardstick or tape measure. DO NOT USE A METAL TAPE MEASURE TO TAKE THESE
MEASUREMENTS ON YOUR HORSE!
Small - fits ponies/yearlings, etc. Approximately 20" around the nose.
Medium - fits cob/Arab size horse heads. Approximately 22" around the nose
Large - fits the average size horse head. Approximately 24" around the nose.
Extra Large - fits the large horse i.e. warmbloods. Approximately 26" around the nose.
XXL - fits the VERY, VERY large horse , i.e. Draft. Approximately 28" around the nose.
The following table shows the measurement between knots for different sizes of horses:
Point
A

B
C
D
E

Location of Knot

End of Rope to Right Ear Knot

Right Ear Knot to Right nose Knot
Right Nose Knot to Left Nose Knot
Left Nose Knot to Throat Latch Knot
Throat Latch Knot to Tie Loop

Small

28 inches
7 inches
8 inches
29 inches
8 inches

Medium
30 inches
8 inches
9 inches
31 inches
9 inches

Large

32 inches
9 inches
10 inches
33 inches
10 inches

XL

34 inches
10 inches
11 inches
35 inches
11 inches

XXL

36 inches
16 inches
12 inches
37 inches
12 inches

F
G
H
I
J

Tie Loop to Left Nose Knot

Left Nose Knot to Right Nose Knot
Right Nose Knot to Throat Latch Knot
Throat Latch Knot to Right Ear Knot
Right Ear Knot to End of Rope

8 inches
8 inches
29 inches
8 inches
28 inches

9 inches
9 inches
31 inches
9 inches
30 inches

10 inches
10 inches
33 inches
10 inches
32 inches

11 inches
11 inches
35 inches
11 inches
34 inches

12 inches
12 inches
37 inches
12 inches
36 inches

This is a recipe for a rope halter you may have to adjust the suggested measurements to fit your horse. These
instructions suggest enough rope for the average horse of each size. This should leave you enough margin of error to have a
bit of rope left over. Youll appreciate this if you go through all the effort to make a halter and it comes up short! If you have
to decide on a size -- It's better to have a halter that is a little bit too big than one that is too small.
Step 2: Using the diagram below, tie overhand knots in the rope at points A, B, C, and D using measurements from the table
in step 1. You may find it easier to label the points on the diagram with the measurements from the table to keep things
straight.
Note:

Step 3: Using the diagram above, tie the tie loop in the correct location by holding

the rope in a loop and making an overhand knot. Make sure that the measurement
between the tie loop and the throat latch (point E) is correct from the table in step 1.
The tie loop should be about 4 inches in length. You may need to flatten the knot if
the ropes get over each other. Take a second to look at this now, because it will be
difficult to fix later.
Step 4: Using the diagram below, tie into the left nose knot from the tie loop. Remember to use the measurement from step

1, point F on the halter. This is your first opportunity to use the double overhand knot. You are going to use the double
overhand to tie into the left nose knot.

Using the above diagram, tie into the right nose knot from the left nose knot, point G. Again, you will use the double
overhand knot to tie the rope into the right nose knot. When you are finished with this step, your halter will have two parallel
pieces of rope tied between the left and right nose knots. These two pieces of rope should be the same length.
Step 5:

Step 6: Using the diagram below, measure the distance between point H

from the right nose knot to the throat latch knot

and tie into the throat latch knot using the double overhand knot. Make sure that the distance between the left nose knot and
the throat latch knot are the same points D and H need to be equal. Now is the time to correct any difference in length.

Step 7: Your halter should be taking shape now.

Arrange the halter so that it looks a bit like the diagram below. Tie into the
right ear knot from the throat latch knot, point I -- using the double overhand knot. Congratulations, that was the last double
overhand knot you will need to tie on the halter. Verify that all of the measurements are correct.

Step 8: Using the above diagram, hold the two long sections (D and H) together and tie

an overhand knot in the bottom. This is the knot that the lead rope goes into under the
chin of the horse. This knot should have two loops about 4-5 inches in length. Dont
tighten this knot until you can fit the horse correctly. This is where you will adjust the
halter to fit your horse.

Trim the rope ends to be the same length and melt them with a lighter/match to seal the ends. Many people will tie
the ends together with a piece of leather while others leave the ends loose. Again, this is a personal preference thing. We
splice them together to make one single piece of rope.
Step 9:

Step 10: Adjust the halter to fit your horse.

If you didnt tighten the knots too tight youll have the ability to move things
around, take up slack, give more room etc. If you need to adjust the size, slip the knots up or down the rope or adjust the size
of the tie rope under the chin. If you are going to ride with the halter you may need more room above the tie rope at the chin
-- we recommend a 2"-4" space above the knot that ties the lead rope into the halter to leave room for the lead rope.
Tying the latch knot
Bring the tie strings through the back of the loop. Hold your fingers below the loop,
bring the strings around the back of the loop, through and under the strings. This is the
best way to tie the latch knot. It wont come loose and it will come apart easily when you
go to take the halter off.

Important: These halters are great training devices, but arent very forgiving the breaking strength on the rope is so high
that a horse wont likely be able to get free on their own if they get into trouble . Do not leave a rope halter on your horse
when you are not using it. Do not tie your horse in a trailer with a rope halter. There is some risk involved in horse training
for both you and the horse. Horses can cause serious injury. Be sensible and dont attempt anything that is outside your
comfort level. This information is intended to illustrate how we apply our training techniques, you are responsible for using
this information wisely. If you dont feel comfortable with your abilities or an exercise, dont do it! Seek advice or assistance
from a professional horse trainer. Stay on the "high side of trouble".

2002 - Natural Horse Supply All rights reserved. Duplication of any material prohibited without express written permission. This
prohibition is not intended to extend to personal non-commercial use, including sharing with others for safety and learning purposes,
provided this copyright notice is attached and you have written permission.