MO1106-EA

Operation Guide 5208

Getting Acquainted
Congratulations upon your selection of this CASIO watch. To get the most out of your
purchase, be sure to read this manual carefully.

Keep the watch exposed to bright light

l l l l l l l l l

Solar cell

Bright Light

The electricity generated by the solar cell of the watch is

stored by a built-in battery. Leaving or using the watch
where it is not exposed to light causes the battery to run
down. Make sure the watch is exposed to light as much as
possible.
When you are not wearing the watch on your wrist,
position the face so it is pointed at a source of bright
light.
You should try to keep the watch outside of your sleeve
as much as possible. Charging is reduced significantly if
the face is only partially covered.
E-1

The watch continues to operate, even when it is not exposed to light. Leaving the
watch in the dark can cause the battery to run down, which will result in some watch
functions being disabled. If the battery goes dead, you will have to re-configure
watch settings after recharging. To ensure normal watch operation, be sure to keep it
exposed to light as much as possible.
Battery charges in the light.
Solar cell
(Converts light to
electrical power.)

Battery discharges in the dark.

Bright Light

The actual level at which some functions are disabled depends on the watch model.
Be sure to read Power Supply (page E-33) for important information you
need to know when exposing the watch to bright light.

If the display of the watch is blank...

If the display of the watch is blank, it means that the watchs Power Saving function
has turned off the display to conserve power.
See Power Saving Function (page E-46) for more information.

Electrical
energy

LEVEL 1
LEVEL 2

All
functions
enabled

LEVEL 3

LEVEL 1
LEVEL 2

Dis- LEVEL 3
charge LEVEL 4

Charge LEVEL 4

Some or all
functions
disabled

Rechargeable battery

E-2

About This Manual

E-3

Depending on the model of your watch, display text

appears either as dark figures on a light background, or
light figures on a dark background. All sample displays
in this manual are shown using dark figures on a light
background.
Button operations are indicated using the letters shown
in the illustration.
Each section of this manual provides you with the
information you need to perform operations in each
mode. Further details and technical information can be
found in the Reference section.

Contents
General Guide ......................................................................................................... E-8
Timekeeping .......................................................................................................... E-10
World Time ............................................................................................................. E-17
Alarms .................................................................................................................... E-20
Countdown Timer .................................................................................................. E-24
Stopwatch .............................................................................................................. E-29
Illumination ............................................................................................................ E-31
Power Supply ........................................................................................................ E-33
Adjusting Home Positions ................................................................................... E-42
Reference .............................................................................................................. E-44
Specifications ....................................................................................................... E-50

E-4

E-5

Procedure Lookup

To configure the countdown timer ...................................................................... E-25

The following is a handy reference list of all the operational procedures contained in
this manual.

To use the countdown timer ................................................................................ E-27

To set the current digital time and date .............................................................. E-11

To measure times with the stopwatch ................................................................ E-30

To change the Daylight Saving Time (summer time) setting ............................ E-15

To illuminate the display ...................................................................................... E-31

To view the time in another city ........................................................................... E-18

To specify the illumination duration ................................................................... E-32

To toggle a city code time between Standard Time

and Daylight Saving Time ............................................................................... E-18

To check the current battery level ....................................................................... E-35

To swap your Home City and World Time City ................................................... E-19

To turn the button operation tone on and off ..................................................... E-45

To set an alarm time ............................................................................................. E-21

To recover from the sleep state ........................................................................... E-47

To adjust home positions ..................................................................................... E-42

To turn an alarm on and off .................................................................................. E-23

To turn the Hourly Time Signal on and off .......................................................... E-23
E-6

E-7

Alarm Mode

World Time Mode

General Guide

Press C to change from mode to mode.

In any mode (except when a setting screen is on the display), press B to illuminate
the face of the watch.
Battery Level Indicator
Timekeeping Mode
C

C
E-8

Countdown Timer Mode

Stopwatch Mode

C
E-9

Operation Guide 5208

Timekeeping

Setting the Digital Time and Date

Use the Timekeeping Mode to set and view the current time and date.
When setting the time, you can also configure settings for the 12/24-hour format.
Each press of D cycles the digital display in the sequence shown below.

Make sure you select your Home City code before you change the current time and
date settings. World Time Mode times are all displayed in accordance with the
Timekeeping Mode settings. Because of this, World Time Mode times will not be
correct if you do not select the proper Home City code before setting the time and
date in the Timekeeping Mode.

Month

PM indicator
Day

Day of week
Hour : Minute

To set the current digital time and date

1. In the Timekeeping Mode, hold down A for about two
City code
seconds, until ADJ appears on the display.
Your current Home City code will be flashing on the
screen.
2. Press C to move the flashing in the sequence shown
below to select other settings.

Second

Second

Second

D
All of the operations in this section are performed in the Timekeeping Mode, which
you can enter by pressing C (page E-8).
E-10

E-11

City Code
Language

DST

12/24-Hour
Format

Illumination
Duration

Seconds

Button Operation
Tone

Hour
Day

Month

Minutes
Year

3. While the setting you want to change is flashing, use D and B to change it as
explained below.
Screen:

To do this:
Change the city code

Do this:
Press D (east) and B (west).

Toggle between Daylight Saving Time

(ON) and Standard Time (OFF).
Toggle between 12-hour (12H) and
24-hour (24H) timekeeping
Reset the seconds to 00

Press D.
Press D.
Press D.

Screen: To do this:
Change the hour or minutes

Do this:
Use D (+) and B ().

Change the year

Change the month or day
Press D.
Toggle the button operation tone
between
(on) and
(off)
Toggle the illumination duration between Press D.
LT1 (approximately 1.5 seconds) and
LT3 (approximately 3 seconds).
Change the day of the week language
Use D (+) and B ().
ENG: English POR: Portuguese
ESP: Spanish FRA: French
DEU: German ITA : Italian
See City Code Table at the back of this manual for a complete list of available
city codes.

E-12

4. Press A to exit the setting screen.

The day of the week is automatically displayed in accordance with the date (year,
month, and day) settings.

12-hour and 24-hour timekeeping

With the 12-hour format, the P (PM) indicator appears to the left of the hour digits for
times in the range of noon to 11:59 p.m. and no indicator appears for times in the
range of midnight to 11:59 a.m.
With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
any indicator.
The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all other modes.

E-13

To change the Daylight Saving Time (summer time) setting

1. In the Timekeeping Mode, hold down A for about two seconds, until ADJ appears
on the display.
Your current Home City code will be flashing on the screen.
2. Press C once to display the DST setting screen.
3. Press D to toggle between Daylight Saving Time (ON displayed) and Standard
Time (OFF displayed).
4. When the setting you want is selected, press A to exit the setting screen.
The DST indicator appears on the display to indicate that Daylight Saving Time is
turned on.

Daylight Saving Time (DST)

Daylight Saving Time (summer time) advances the time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
E-14

Analog Timekeeping
The analog time of this watch is synchronized with the digital time. The analog time
setting is adjusted automatically whenever you change the digital time.
Note
The hands for the analog timepiece move to adjust to a new setting whenever any of
the following occurs.
When you change the digital time setting
When you change the Home City code and/or DST setting
If the analog time does not match the digital time for any reason, use the procedure
described under To adjust home positions (page E-42) to match the analog setting
to the digital setting.
Whenever you need to adjust both the digital and the analog time settings, make
sure you adjust the digital setting first.
Depending on how much the hands have to move in order to synchronize to the
digital time, it may take some time before they stop moving.

E-15

World Time
City code

Current time in
selected city

The World Time Mode digitally displays the current time in

48 cities (31 time zones) around the world.
If the current time shown for a city is wrong, check your
Home City time settings and make the necessary
changes (page E-11).
After you press C to enter the World Time Mode, your
currently selected World Time City code will appear on
the digital display for about two seconds. After that, the
current time in that city will appear.
All of the operations in this section are performed in the
World Time Mode, which you enter by pressing C
(page E-9).

E-16

To view the time in another city

If you press D while in the World Time Mode, your currently selected World Time City
code will appear on the digital display for about two seconds. After that, the current
time in that city will appear. Pressing D again while the World Time City code is
displayed will scroll to the next city code.
For full information on city codes, see the City Code Table at the back of this
manual.
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, use D to display the city code
(time zone) whose Standard Time/Daylight Saving Time
setting you want to change.
2. Hold down A to toggle Daylight Saving Time (DST
indicator displayed) and Standard Time (DST indicator
not displayed).
The DST indicator will appear on the display whenever
DST indicator
you display a city code for which Daylight Saving Time is
turned on.
E-18

E-17

Note that the DST/Standard Time setting affects only the currently displayed city
code. Other city codes are not affected.

Swapping your Home City and World Time City

You can use the procedure below to swap your Home City and World Time City. This
changes your Home City to your World Time City, and your World Time City to your
Home City. This capability can come in handy when you frequently travel between two
cities in different time zones.

To swap your Home City and World Time City

1. In the World Time Mode, use D to select the World Time City you want.
2. Hold down A and B until the watch beeps.
This will make the World Time City you selected in step 1 your Home City, and cause
the hour and minute hands to move to the current time in that city. At the same time,
it will change the Home City you had selected prior to step 2 your World Time City.
After swapping the Home City and World Time City, the watch stays in the World
Time Mode with the city that was selected as the Home City prior to step 2 now
displayed as the World Time City.
E-19

Operation Guide 5208

To set an alarm time
Alarm number

Alarm time
About 2 seconds

The Alarm Mode lets you configure five daily alarms. You
also can use it to turn the Hourly Time Signal on or off.
The watch beeps for about 10 seconds when an alarm
time is reached.
Turning on the Hourly Time Signal causes the watch to
beep on the hour every hour.
All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C (page
E-9).

Alarms

1. In the Alarm Mode, use D to scroll through the alarm screens until the one whose
time you want to set is displayed.

Alarm time
(Hour : Minutes)

AL1

AL2

AL3

SIG

AL5

AL4

The alarm screens are AL1, AL2, AL3, AL4, and AL5.

E-20

E-21

2. After you select an alarm, hold down A for about two seconds until the hour setting
of the alarm time starts to flash. This is the setting mode.
This operation turns on the alarm automatically.
3. Press C to move the flashing between the hour and minute settings.
4. While a setting is flashing, use D (+) and B () to change it.
5. Press A to exit the setting mode.

To turn an alarm on and off

1. In the Alarm Mode, use D to select an alarm.
Alarm on indicator
2. Press A to toggle it on and off.

Alarm Operation
The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the
watch is in.
Alarm and Hourly Time Signal operations are performed in accordance with the
Timekeeping Mode time.
To stop the alarm tone after it starts to sound, press any button.

To turn the Hourly Time Signal on and off

1. In the Alarm Mode, use D to select the Hourly Time
Hourly time signal
Signal (SIG) (page E-21).
on indicator
2. Press A to toggle it on and off.

E-22

E-23

Countdown Timer
Timer 1

Timer 2

The watch emits a short beep whenever either of the timers reaches the end of its
countdown during an ongoing timer operation. The watch emits a 5-second beep
when the end of the final timer operation (specified by the number of repeats) is
reached.
All of the operations in this section are performed in the Countdown Timer Mode,
which you enter by pressing C (page E-9).

Countdown End Beeper

2 seconds

Seconds

Seconds

Minutes

Minutes

Dual timers can be set with two different starting times. The watch can be configured
so the two timers alternate, so when one reaches the end of its countdown, the other
timer starts. You can specify a number of repeats value from 1 (once) to 10 (ten
times), which controls how many times the two-timer countdown operation is
performed. The starting time of each timer can be set in five-second steps up to 99
minutes, 55 seconds.

To configure the countdown timer

1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down A until the current
countdown start time starts to flash, which indicates the
setting screen.
If the countdown start time is not displayed, use the
procedure under To use the countdown timer (page
E-27) to display it.

E-25

To use the countdown timer

Current timer time

Timer (1 or 2)

(Reset)

Number of Repeats
3. When the setting you want to change is flashing, use D and B to change it as
described below.
Setting
Minutes, Seconds

Screen

Number of Repeats

Button Operation
Use D (+) and B () to change the setting.
Use D (+) and B () to change the setting.

To disable either timer, set 00'00" as its countdown start time.

4. Press A to exit the setting screen.
E-26

Even if you exit the Countdown Timer Mode, the countdown timer operation
continues and the watch beeps as required.
To stop a countdown operation completely, first pause it (by pressing D), and then
press A. This returns the countdown time to its starting value.

2 seconds
(Start/Stop)

Preset number of repeats

Press D while in the Countdown Timer Mode to start the countdown timer.
Pressing A while a countdown is in progress will display the repeat count (current
repeat count/preset number of repeats). The ongoing countdown will reappear
automatically after about two seconds.
The countdown is performed by alternating between Timer 1 and Timer 2. A short
beep is emitted to signal a changeover from one timer to the other.
Pressing A while a countdown timer is stopped resets that time to the start time specified
by you.
Press D to pause a countdown. Press D again to resume.
The watch emits a 5-second beep when the end of the final timer operation
(specified by the number of repeats) is reached.
E-27

Stopwatch

Minutes
Seconds

E-28

Current repeat count

2. Press C to move the flashing in the sequence shown below to select other
settings.
Timer 1
Timer 1
Timer 2
Timer 2
Minutes
Seconds
Minutes
Seconds

E-24

The countdown end beeper lets you know when the countdown reaches zero. The
beeper stops after about 5 seconds or when you press any button.

The stopwatch lets you measure elapsed time, split times,

and two finishes.
The display range of the stopwatch is 59 minutes, 59.99
seconds.
The stopwatch continues to run until you stop it. If it
reaches its limit, it restarts from zero.
Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing C
(page E-9).

E-29

Operation Guide 5208

To measure times with the stopwatch

Split Time
D

D
Re-start

D
Stop

A
Clear

A
Split

A
Split release

D
Stop

A
Clear

D
Stop

A
Split release

A
Clear

The split time screen alternates between a split indicator (SPL) and the split time at
two-second intervals.
Two Finishes
D

A
Split

Start

First runner finishes.

Display time of first
runner.

Second runner
finishes.

An LED (light-emitting diode) illuminate the display for

easy reading in the dark.

lll l lll

lll

Start

D
Stop

lll

Start

Illumination

llllll

Elapsed Time
D

To illuminate the display

In any mode (except when a setting screen is on the
display), press B to turn on illumination.
You can use the procedure below to select either 1.5
seconds or 3 seconds as the illumination duration. When
you press B, the illumination will remain on for about
1.5 seconds or 3 seconds, depending on the current
illumination duration setting.

Display time of
second runner.

E-30

E-31

To specify the illumination duration

1. In the Timekeeping Mode, hold down A until the
display contents start to flash. This is the setting screen.
2. Press C 10 times until the current illumination duration
setting (LT1 or LT3) appears.
3. Press D to toggle the setting between LT1
(approximately 1.5 seconds) and LT3 (approximately 3
seconds).
4. Press A to exit the setting screen.

Power Supply
This watch is equipped with a solar cell and a rechargeable battery that is charged by
the electrical power produced by the solar cell. The illustration shown below shows
how you should position the watch for charging.
Example: Orient the watch so its face is
pointing at a light source.
The illustration shows how to position a
watch with a resin band.
Note that charging efficiency drops when
any part of the solar cell is blocked by
clothing, etc.
You should try to keep the watch outside of
your sleeve as much as possible. Charging
is reduced significantly if the face is
covered only partially.

E-32

Solar cell

E-33

Important!
Storing the watch for long periods in an area where there is no light or wearing it in
such a way that it is blocked from exposure to light can cause rechargeable battery
power to run down. Be sure that the watch is exposed to bright light whenever
possible.
This watch uses a rechargeable battery to store power produced by the solar cell, so
regular battery replacement is not required. However, after very long use, the
rechargeable battery may lose its ability to achieve a full charge. If you experience
problems getting the rechargeable battery to charge fully, contact your dealer or
CASIO distributor about having it replaced.
Never try to remove or replace the watchs rechargeable battery yourself. Use of the
wrong type of battery can damage the watch.
The current time and all other settings return to their initial factory defaults whenever
battery power drops to Level 5 (pages E-36 and E-37) and when you have the
battery replaced.
Turn on the watchs Power Saving function (page E-46) and keep it in an area
normally exposed to bright light when storing it for long periods. This helps to keep
the rechargeable battery from going dead.

To check the current battery level

When the battery level is at Level 1 (HI) or Level 2 (MID), the corresponding battery
level indicator (HI or MID, page E-8) will appear only if you press C in the
Timekeeping Mode. For other battery levels, the applicable indicator appears
automatically.
Battery level indicator

E-34

E-35

The battery level indicator shows the current power level of the rechargeable battery.
Level

Battery Level Indicator

Function Status

All functions enabled.

All functions enabled.

Key operation tone, alarm, Hourly Time
Signal, and illumination disabled.

The
indicator at Level 3 tells you that battery power is very low, and that
exposure to bright light for charging is required as soon as possible.
At Level 5, all functions are disabled and settings return to their initial factory
defaults. Once the battery reaches Level 2 after falling to Level 5, reconfigure the
current time, date, and other settings.
Display indicators reappear as soon as the battery is charged from Level 5 to Level 2.
Leaving the watch exposed to direct sunlight or some other very strong light source
can cause the battery power indicator to show a reading temporarily that is higher
than the actual battery level. The correct battery level should be indicated after a few
minutes.

(Charge Soon Alert)

All hands stop at 12 oclock. All operations

disabled.

All functions, including timekeeping,

disabled and initialized.

E-36

Recover indicator

E-38

E-37

Performing illumination, or beeper operations during a

short period may cause
(recover) to appear on the
display.
After some time, battery power will recover and
(recover) will disappear, indicating that the above
functions are enabled again.
If
(recover) appears frequently, it probably means
that remaining battery power is low. Leave the watch in
bright light to allow it to charge.

Charging Precautions
Certain charging conditions can cause the watch to become very hot. Avoid leaving
the watch in the areas described below whenever charging its rechargeable battery.
Also note that allowing the watch to become very hot can cause its liquid crystal
display to black out. The appearance of the LCD should become normal again when
the watch returns to a lower temperature.
Warning!
Leaving the watch in bright light to charge its rechargeable battery can cause it
to become quite hot. Take care when handling the watch to avoid burn injury.
The watch can become particularly hot when exposed to the following
conditions for long periods.
On the dashboard of a car parked in direct sunlight
Too close to an incandescent lamp
Under direct sunlight

E-39

Operation Guide 5208

Charging Guide
The following table shows the amount of time the watch needs to be exposed to light
each day in order to generate enough power for normal daily operations.
Exposure Level (Brightness)

Level 2

Level 1

3 hours

35 hours

10 hours

10 hours

133 hours

36 hours

16 hours

216 hours

58 hours

194 hours

--------

--------

Outdoor Sunlight
(50,000 lux)
Sunlight Through a
Window (10,000 lux)
Daylight Through a
Window on a Cloudy
Day (5,000 lux)
Indoor Fluorescent
Lighting (500 lux)

Approximate Exposure Time

Level 5
Level 4
Level 3

For details about the battery operating time and daily operating conditions, see the
Power Supply section of the Specifications (page E-52).
Stable operation is promoted by frequent exposure to light.

Exposure Level
(Brightness)

Outdoor Sunlight (50,000 lux)

Sunlight Through a Window (10,000 lux)
Daylight Through a Window on a Cloudy Day (5,000 lux)
Indoor Fluorescent Lighting (500 lux)

Approximate
Exposure Time
8 minutes
30 minutes
48 minutes
8 hours

Recovery Times
The table below shows the amount exposure that is required to take the battery from
one level to the next.

The above exposure time values are all for reference only. Actual required exposure
times depend on lighting conditions.
E-40

E-41

The hour and minute hands should move to 12 oclock

(their home position), and 0:00 will flash on the
display.
If the hour and minute hands are not at 12 oclock,
use D (+) and B () to move them there.
Holding down either button will cause the hands to
move at high speed. Once started, high-speed hand
movement will continue even if you release the button.
To stop high-speed hand movement, press any button.
High-speed hand movement started with the D (+)
button will stop automatically after 12 revolutions of
the minute hand. If started with the B () button, it
will stop after one revolution of the minute hand.

Adjusting Home Positions

Strong magnetism or impact can cause the hands of the watch to be off. If this
happens, perform the applicable home position adjustment procedures in this section.
Hand home position adjustment is not required if the analog time and digital time are
the same in the Timekeeping Mode.

To adjust home positions

1. In the Timekeeping Mode, hold down A for about five seconds. You can release the
button after H.SET appears on the display.
Though ADJ will appear on the display after about two seconds, do not release
the button yet. Keep it depressed until H.SET appears.

Correct hour and

minute hand positions

2. After everything is the way you want, press A to return to the Timekeeping Mode.
After performing home position adjustment, enter the Timekeeping Mode and check
to make sure that the analog hands and the digital display indicate the same time. If
they do not, perform home position adjustment again.
E-42

E-43

Reference
This section contains more detailed and technical information about watch operation.
It also contains important precautions and notes about the various features and
functions of this watch.

Button Operation Tone

The button operation tone sounds any time you press one of the watchs buttons. You
can turn the button operation tone on or off as desired.
Even if you turn off the button operation tone, alarms, the Hourly Time Signal, and
other beepers all operate normally.

To turn the button operation tone on and off

1. In the Timekeeping Mode, hold down A for about two
seconds, until ADJ appears on the display.
Your current Home City code will be flashing on the
screen.
2. Press C nine times until the current button operation
tone setting (
or
) appears.
3. Press D to toggle the setting between
(tone on)
and
(tone off).
4. Press A to exit the setting screen.

E-44

E-45

Power Saving Function

The Power Saving function enters a sleep state
automatically whenever the watch is left in an area for a
certain period where it is dark (except if the watch is in the
Stopwatch or Timer mode). The table below shows how
watch functions are affected by the Power Saving
function.

Elapsed Time in Dark

60 to 70 minutes

Display
Blank

6 or 7 days

Operation
All functions enabled, except for the display
Beeper tone, illumination, and display disabled
Analog timekeeping stopped at 12 oclock

Wearing the watch inside the sleeve of clothing can cause it to enter the sleep state.
The watch will not enter the sleep state between 6:00 AM and 9:59 PM. If the watch
is already in the sleep state when 6:00 AM arrives, however, it will remain in the
sleep state.

To recover from the sleep state

Perform any one of the following operations.
Move the watch to a well-lit area.
Press any button.

E-46

Auto Return Features

If you leave the watch in the Alarm Mode, or with the battery level indicator displayed
for two or three minutes without performing any operation, it automatically returns to
the Timekeeping Mode.
If you leave the watch with a flashing setting on the display for two or three minutes
without performing any operation, the watch automatically exits the setting screen.

Scrolling

The B and D buttons are used in various modes and setting screens to scroll
through data on the display. In most cases, holding down these buttons during a scroll
operation scrolls through the data at high speed.

Initial Screens
When you enter the World Time Mode or Alarm Mode, the data you were viewing
when you last exited the mode appears first.

E-48

E-47

Timekeeping
Resetting the seconds to 00 while the current count is in the range of 30 to 59
causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are
reset to 00 without changing the minutes.
The year can be set in the range of 2000 to 2099.
The watchs built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to change
it except after you have the watchs battery replaced or when battery power drops to
Level 5.
The current time for all city codes in the Timekeeping Mode and World Time Mode is
calculated in accordance with the Coordinated Universal Time (UTC) for each city,
based on your Home City time setting.

Illumination Precautions

Illumination may be hard to see when viewed under direct sunlight.

Illumination automatically dims if it is lit and an alarm or time up alarm sounds.
Frequent use of illumination runs down the battery.
E-49

Operation Guide 5208

Specifications
Accuracy at normal temperature: 30 seconds a month
Digital Timekeeping: Hour, minutes, seconds, p.m. (P), month, day, day of the week
Time system: Switchable between 12-hour and 24-hour formats
Calendar system: Full Auto-calendar pre-programmed from the year
2000 to 2099
Other: Home city code (can be assigned one of 48 city codes); Daylight
Saving Time (summer time)/Standard Time
Analog Timekeeping: Hour, minutes (hand moves every 20 seconds)
World Time: 48 cities (31 time zones)
Other: Standard Time/Daylight Saving Time (summer time)
Alarms: 5 daily alarms; Hourly Time Signal

Countdown Timer:
Number of timers: 2 (one set)
Setting unit: 5 seconds
Range: 99 minutes 55 seconds each timer
Countdown unit: 1 second
Number of repeats: 1 to 10
Other: 5-second time up beeper
Stopwatch:
Measuring unit: 1/100 second
Measuring capacity: 59' 59.99''
Measuring modes: Elapsed time, split time, two finishes
Illumination: LED (light-emitting diode); Selectable illumination duration
Other: Battery level indicator; Power Saving; Button operation tone on/off;
6 languages for day of the week

E-50

E-51

Power Supply: Solar cell and a rechargeable battery

Approximate Battery Operating Time
10 months (from full charge to Level 4 when the watch is not exposed to light)
under the following conditions:
Display on 18 hours per day, sleep state 6 hours per day
1 illumination operation (1.5 seconds) per day
10 seconds of alarm operation per day

Frequent use of illumination can shorten battery operating time.

E-52

City Code Table

City
Code
PPG
HNL
ANC
YVR
LAX
YEA
DEN
MEX
CHI
NYC
SCL
YHZ
YYT

City
Pago Pago
Honolulu
Anchorage
Vancouver
Los Angeles
Edmonton
Denver
Mexico City
Chicago
New York
Santiago
Halifax
St. Johns

UTC Offset/
GMT Differential
11
10
9
8
7
6
5
4
3.5

City
UTC Offset/
City
Code
GMT Differential
RIO Rio De Janeiro
3
FEN Fernando de Noronha
2
1
RAI
Praia
UTC
0
LIS
Lisbon
LON
London
MAD
Madrid
PAR
Paris
ROM
Rome
+1
BER
Berlin
STO
Stockholm
ATH
Athens
CAI
Cairo
+2
JRS
Jerusalem

City
Code
MOW
JED
THR
DXB
KBL
KHI
DEL
KTM
DAC
RGN
BKK

City
Moscow
Jeddah
Tehran
Dubai
Kabul
Karachi
Delhi
Kathmandu
Dhaka
Yangon
Bangkok

UTC Offset/
GMT Differential
+3
+3.5
+4
+4.5
+5
+5.5
+5.75
+6
+6.5
+7

City
Code
SIN
HKG
BJS
TPE
SEL
TYO
ADL
GUM
SYD
NOU
WLG

City
Singapore
Hong Kong
Beijing
Taipei
Seoul
Tokyo
Adelaide
Guam
Sydney
Noumea
Wellington

UTC Offset/
GMT Differential

+8

+9
+9.5
+10
+11
+12

Based on data as of December 2010.

The rules governing global times (UTC offset and GMT differential) and summer
time are determined by each individual country.
L-1