FiHterHfter

FaJaJdfiHter uJit
VeJtiHateur fiHtre
VeJtiHatKr
FiHterfHGt
VeJtiHatKrefiHtrK
VeJtiHadKr cKJ fiHtrK

3237xxx
3238xxx
3239xxx
3240xxx

*KJtage IJstaHHatiKJs uJd BedieJuJgsaJHeituJg

AsseIbHy aJd KperatiJg iJstructiKJs
+Ktice deIpHKi diJstaHHatiKJ et de IKJtage
*KJtage eJ bedieJiJgshaJdHeidiJg
*KJtage Kch haJteriJgsaJvisJiJg
IstruViKJi di IKJtaggiK e fuJViKJaIeJtK
IJstrucciKJes de IKJtaFe y fuJciKJaIieJtK

3241xxx
3243xxx
3244xxx
3245xxx

CKJteJts
1

+Ktes KJ dKcuIeJtatiKJ      4

11
12
13

,ther appHicabHe dKcuIeJts  4

ReteJtiKJ Kf dKcuIeJts      4
SyIbKHs used              4

Safety JKtes                 5

Device descriptiKJ            5

31
3.1.1
3.1.2
3.1.3
3.1.4
32
33

FuJctiKJaH descriptiKJ       5
Main components . . . . . . . . . . . 5
Control. . . . . . . . . . . . . . . . . . . . 6
Safety equipment . . . . . . . . . . . 6
Filter mats . . . . . . . . . . . . . . . . . 6
PrKper use                 6
ScKpe Kf suppHy            6

AsseIbHy aJd cKJJectiKJ     7

41

42
4.2.1
4.2.2
43
4.3.1
4.3.2
44
4.4.1
4.4.2
4.4.3

ChKKsiJg the iJstaHHatiKJ

site                       7
AsseIbHy iJstructiKJs       7
General . . . . . . . . . . . . . . . . . . . 7
Layout of the components
in the enclosure. . . . . . . . . . . . . 7
FittiJg the faJaJdfiHter uJit
Kr KutHet fiHter               7
Cutting out the enclosure . . . . . 7
Fitting the fan-and-filter unit . . . 8
+Ktes KJ eHectricaH
cKJJectiKJ                 8
Connection data . . . . . . . . . . . . 8
Overvoltage protection and
supply line load . . . . . . . . . . . . . 9
PE conductor connection . . . . . 9

CarryiJg Kut the eHectricaH

cKJJectiKJ                  9
51
52

53

CKJJectiJg the pKwer suppHy 9

RKtatiJg the vKHtage
cKJJectiKJ                9
ChaJgiJg the directiKJ Kf
airfHKw                   10

CKIIissiKJiJg             10

IJstaHHiJg aJd chaJgiJg

the fiHter                   10

IJspectiKJ aJd
IaiJteJaJce               11

StKrage aJd dispKsaH        11

10 TechJicaH specificatiKJs      12
11 CutKutdriHHiJg diIeJsiKJs   16
12 E*C faJKutHet fiHter         17
13 CKJJectiKJ diagraIs        18
14 EC decHaratiKJ Kf
cKJfKrIity                 20

Rittal fan-and-filter unit assembly and operating instructions

E+

1 +Ktes KJ dKcuIeJtatiKJ
E+

1 +Ktes KJ dKcuIeJtatiKJ
These assembly instructions are aimed at
tradespersons who are familiar with
assembly and installation of the
fan-and-filter unit
trained specialists who are familiar with
operation of the fan-and-filter unit

1.1 Other applicable documents

Assembly and operating instructions exist
as paper documents and/or on CD-ROM
for the unit types described here and are
enclosed with the equipment.
We cannot accept any liability for damage
associated with failure to observe these
instructions. Where applicable, the instructions for any accessories used also apply.

1.3 Symbols used

The buHHet pKiJt iJdicates aJ

actiKJ tK be perfKrIed

DaJger!
IIIediate daJger tK Hife aJd
HiIb!

CautiKJ!
PKteJtiaH threat tK the prKduct
aJd its eJvirKJIeJt

1.2 Retention of documents

These instructions and all associated
documents constitute an integral part of
the product. They must be given to the
plant operator. The operator is responsible for storage of the documents so they
are readily available when needed.

+Kte
Useful information and special
features.

Rittal fan-and-filter unit assembly and operating instructions

2 Safety JKtes
2 Safety JKtes

3 Device descriptiKJ

Please observe the following safety notes

when assembling and operating the unit:
Assembly, installation and servicing may
only be performed by properly trained
specialists
Do not obstruct the air inlet and outlet of
the fan-and-filter unit inside and outside
the enclosure (see also section
4.2.2 Layout of the components in the
enclosure, page 7)
The heat loss of the components
installed in the enclosure must not
exceed the specific air throughput
of the fan-and-filter unit
The louvres must always have their
opening pointing downwards
Use only original spare parts and
accessories
Do not make any changes to the fanand-filter unit other than those described in these and other applicable
instructions
The fan-and-filter unit must only be
connected to the mains with the system
de-energised. Connect the pre-fuse
specified on the rating plate
Changes to the direction of airflow must
only be carried out with the system deenergised
Changes to the positioning of the mains
connection must only be carried out with
the system de-energised
Never insert your fingers into the rotating fan blade
Electrical connection and any repairs
may only be carried out by authorised
specialist personnel

Depending on the model chosen, your fanand-filter unit may vary in appearance from
the illustrations contained in these instructions. However, the functions are identical
in principle.
3

Fig. 1:

Device description

(ey
1 Function logo
(to release the louvred grille)
2 Louvred grille
3 Filter box with filter mat
4 Fan housing
5 Variable electrical connection

3.1 Functional description

The fan-and-filter unit in conjunction with
the corresponding outlet filter(s) is used
to dissipate heat loss from enclosures,
ventilate the enclosure and protect
temperature-sensitive components. This is
achieved via the direct infeed of ambient
air, the temperature of which must be less
than the admissible enclosure interior
temperature. The system is fitted into
prepared cut-outs.
311 *aiJ cKIpKJeJts
The fan-and-filter unit is comprised of
the following four main components: Fan
motor, filter box, louvred grille with function
logo and filter rmedium.

Rittal fan-and-filter unit assembly and operating instructions

E+

3 Device descriptiKJ
E+

312 CKJtrKH
Rittal fan-and-filter units may be controlled
more efficiently using a thermostat
(Model No. 3110.000), digital temperature
display (Model No. 3114.200),
temperature-dependent speed control
(Model No. 3120.200, 3235.440, 3235.450)
and/or hygrostat (Model No. 3118.000).
+Kte
The control unit 3120.200 can
only be used with single-phase
AC units. The control units
3235.440 and 3235.450 can
only be used with fan-and-filter
units with integrated control
interface (EC fan-and-filter units
and fan-and-filter units with
EMC shielding from an air
throughput of 180 m3/h.
Model No. 3240.500/600,
3241.500/600, 3243.500/600,
3244.500/600, 3245.500/600.
313 Safety equipIeJt
The fan is equipped with thermal winding
protection devices for protection against
excess current and, in some cases,
against overtemperature. For rotary current
fans, the winding protection is located in
the star earthing of the motor.
314 FiHter Iats
The fan-and-filter unit/outlet filter is supplied with a standard filter mat already installed. The filter must be checked regularly in accordance with the level of dust
exposure and replaced as necessary.
In order to increase the protection category, and in the case of dust with a grain size
of < 10 m, we recommend the use of fine
filter mats.

3.2 Proper use

Rittal fan-and-filter units were developed
and designed in accordance with the state
of the art and the recognised rules governing technical safety. Nevertheless, if used
improperly, they may pose a threat to life
and limb or cause damage to property.
The unit is only intended for ventilating enclosures and electronic cases. Any other
use is deemed improper. The manufacturer will not be liable for any damages
caused as a result of improper use, or for
incorrect assembly, installation and use.
All risk is borne solely by the user.
Proper usage also includes the observation of all valid documents and compliance with the inspection and servicing
conditions.

3.3 Scope of supply

The fan is supplied in a packaging unit
in a fully assembled state and ready to
connect.
Please check the scope of supply for
completeness.
Qty

DescriptiKJ

Fan-and-filter unit

Mounting screws (not for

3237.1xx to 3239.1xx)
Assembly, installation and
operating instructions

1
1
1
Tab. 1:

Drilling template, self-adhesive

Standard or EMC filter mat
Scope of supply

+Kte
The air throughput volume will
be reduced.
Special filter mats are required
for EMC fan-and-filter units
(see accessories).
6

Rittal fan-and-filter unit assembly and operating instructions

4 AsseIbHy aJd cKJJectiKJ

4 AsseIbHy aJd cKJJectiKJ
4.1 Choosing the installation site
When choosing the installation site for the
enclosure, please observe the following:
The site for the enclosure, and hence
the arrangement of the fan-and-filter
unit, must be carefully selected so as to
ensure good ventilation
The site must be free from excessive dirt
and moisture
Fan-and-filter units must always be installed on vertical panels (door or walls)
The ambient temperature must be lower
than the permissible enclosure interior
temperature
The mains connection data as stated
on the rating plate of the unit must be
guaranteed

4.2 Assembly instructions

421 GeJeraH
Check the packaging carefully for signs
of damage. Any packaging damage may
be the cause of a subsequent functional
failure
The fan-and-filter and outlet filter must
always be mounted on an enclosure in
order to ensure air exchange
+Kte
The outlet filter should be at
least the same size as the
fan-and-filter unit.
The enclosure must be sealed on all
sides (IP 54). If the enclosure has a leak,
unfiltered, contaminated air may enter
the enclosure, depending on the direction of airflow of the fan
If two or more fan-and-filter units are arranged one above the other, a minimum
spacing of 15 mm should be observed
(between drilling templates). Only then is it
guaranteed that the louvred grille can be
opened without restriction.

422 )ayKut Kf the cKIpKJeJts iJ the

eJcHKsure
Observe the air flows from the internal fans
of installed electronic components. For installation, it is important to ensure that the
airflows of fans and built-in electronic components do not have a negative influence
on one another (air short-circuit). The corresponding minimum distances between the
fan and component must be observed in
order to ensure unhindered air circulation.

4.3 Fitting the fan-and-filter unit or

outlet filter
The fan-and-filter unit or outlet filter is
mounted on a vertical panel of the
enclosure:
For this purpose, the appropriate door,
side or rear panel must be cut out using
the supplied drilling template.
The fan-and-filter unit is generally fitted in
the lower part of the enclosure, and the
outlet filter in the upper part.
431 CuttiJg Kut the eJcHKsure
Stick the self-adhesive drilling template
supplied to the envisaged position on
the door, side or rear panel of the
enclosure.
Lines indicating the dimensions of cut-outs
and drilling specifications for mounting
and fixing of the fan (only necessary for
sheet metal thickness 2.5 mm and above)
are to be found on the drilling template.
See also fig. 8 and fig. 9 on page 16.
RisG Kf iJFury!
CarefuHHy deburr aHH cutKuts
tK preveJt iJFuries caused by
sharp edges
Make the cut-outs including the line

width as per the drilling template.

Deburr the cut-outs.

Rittal fan-and-filter unit assembly and operating instructions

E+

4 AsseIbHy aJd cKJJectiKJ

E+

432 FittiJg the faJaJdfiHter uJit

The fan may be fitted without tools, by
simply snapping into the preconfigured
mounting cut-out
Make sure that the clips have snapped
into place properly to guarantee secure
mounting
From a sheet metal thickness of 2 mm,
the clips should be pressed in
individually
From a sheet metal thickness of 2.5 mm,
the fan-and-filter unit must be screwfastened in addition
To drill the lower holes, it is necessary to
remove the louvred grille as shown in
fig. 2
3237.xxx
3238.xxx

3239.xxx
3240.xxx
3241.xxx
3243.xxx
3244.xxx
3245.xxx

Fig. 2:

Release the louvred grille

If transporting, it is necessary that you

screw-fasten the fan to prevent it from
falling out of the mounting cut-out.
The fan-and-filter unit is a rotating component that may transfer vibrations and
oscillations. Appropriate measures to
decouple vibration must be taken in
advance by the company responsible
for the overall plant or system.

The protection category can be increased by means of the following

accessories:
IP 55 by using an additional fine filter
mat or hose-proof hood
IP 56 by using a hose-proof hood
+Kte
To increase the protection category, an additional fine filter
mat or hose-proof hood must
be used in both the fan-andfilter unit and the outlet filter.

4.4 Notes on electrical connection

When performing the electrical connection, it
is important to observe all valid national and
regional regulations as well as the provisions
of the responsible power supply company.
Electrical connection must only be carried
out by a qualified electrician who is responsible for compliance with the existing standards and regulations.
441 CKJJectiKJ data
The voltage and frequency of the connection must correspond to the values
stated on the rating plate
Electrical connection and any repairs
may only be carried out by authorised
specialist personnel
Use only original spare parts!
For 1~ and 24 V (DC) fans, install the
pre-fuse prescribed on the rating plate
(circuit-breaker or slow fuse) to protect
against short-circuiting
With the rotary current variant, install the
pre-fuse prescribed on the rating plate or
a circuit-breaker/back-up protection to
protect against short-circuiting, and set
it to the prescribed rating value
The direction of airflow and the direction
of rotation are each marked on the motor
housing with an arrow
If a phase is missing, the fan will not
start. If the rotary field is incorrect, the
fan will run backwards

Rittal fan-and-filter unit assembly and operating instructions

EHectricaH cKJJectiKJ
442 ,vervKHtage prKtectiKJ aJd suppHy
HiJe HKad
The unit does not have its own overvoltage
protection. Measures must be taken by the
operator at the supply end to ensure effective lightning and overvoltage protection.
The mains voltage must not exceed a
tolerance of 10%.
443 PE cKJductKr cKJJectiKJ
The PE conductor connection must be
connected to the PE conductor system of
the overall system.

E+

CautiKJ!
If JK wire eJd ferruHes are
used the iJsuHatiKJ Kf the
iJdividuaH wires should be
stripped to a max. of 9 mm
(tK cKIpHy with cHearaJce
aJd creepage distaJces)
Re-attach the electrical connection

cover.
+Kte
Fan-and-filter unit 3237.xxx is
connected by way of two single wires which are led out of
the unit.

5 CarryiJg Kut the eHectricaH

cKJJectiKJ
5.1 Connecting the power supply

5.2 Rotating the voltage connection

Complete the electrical connection by

If the position of the voltage connection is

not ideally accessible, it may be rotated
through 90 and snapped into position.
To this end, press down on the release
button of the bayonet connection at the rear
of the fan. Units 3238.xxx to 3239.xxx are
released by pulling out the clip (see fig. 4)
of the bayonet connection.

following the wiring plans.

+Kte
For technical data, refer to the
rating plate.
Remove the red cover from the electrical

connection.
3238.xxx
3239.xxx

Fig. 4:
Fig. 3:

Access the electrical connection

Insert the connection cable with wire end

ferrules into the screwless spring terminals. Choose an appropriate pre-fuse

according to the line cross-section
(2 x 0.75 2.5 mm multi-wire,
2 x 1.5 2.5 mm fine-wire soldered).

Release the bayonet connection

Units 3240.xxx, 3241.xxx, 3243.xxx to

3245.xxx are released by pressing the release button of the bayonet connection
(see fig. 5), located on the opposite corner from the connection terminal.

Rittal fan-and-filter unit assembly and operating instructions

6 CKIIissiKJiJg
7 IJstaHHiJg aJd chaJgiJg
the fiHter

E+

Fig. 5:

Release the bayonet connection

5.3 Changing the direction of airflow

The direction of airflow blows into the enclosure from the outside as standard. Should it
become necessary to change the direction of
airflow for technical reasons (space, specific
component air routing etc.), this is easily
achieved. Simply release the fan housing
and rotate it through 180. To release, please
follow the same procedure as described under 5.2 Rotating the voltage connection,
page 9.
Please also observe the instructions outlined
under 4.2.1 General, page 7.

6 CKIIissiKJiJg
The fan-and-filter unit operates automatically, in other words, the fan will start up
once the power has been switched on.
Depending on the model, the following
voltage variants are supported:
24 V DC
115 V, 1~
230 V, 1~
400/460 V, 3-phase

10

The fan-and-filter unit and outlet filter are

supplied as standard with a standard filter
mat for the pre-filtering of dry, coarse dust
and lint. In order to increase the protection
category, and in the case of dust with a
grain size of < 10 m, we recommend the
use of fine filter mats (optionally available).
The filter should be checked at regular intervals in accordance with the level of dust
exposure (recommended: at the latest after 2,000 operating hours) and replaced as
necessary.
+Kte
Use only original Rittal filters
which bear the Rittal logo in order
to safeguard the designated protection category, air throughout
and operating approvals.
RisG Kf iJFury!
,JHy chaJge the fiHter Iat
whiHe the faJ rKtKr is
statiKJary
+ever iJsert yKur fiJgers iJtK
the faJ rKtKr
To insert or replace the filter, proceed as
follows (direction of airflow: drawing from
outside and blowing into the enclosure):
First press the catch of the louvred grill
(Rittal logo) up slightly with one finger
(see fig. 6)
Once it is released, the louvred grille can
be dropped open by approx. 70 or 90
If necessary, first place the fine filter mat
into the housing
Ensure that the open (roughened) side
faces towards the louvred grille
Then insert the enclosed standard filter
mat
Here again, ensure that the open side
(without Rittal logo) faces towards the
louvred grille (see fig. 7)
Now push the louvred grille back onto
the enclosure until it snaps audibly into
position.

Rittal fan-and-filter unit assembly and operating instructions

8 IJspectiKJ aJd IaiJteJaJce

Fig. 6:

Release the louvred grille

Open (roughened)
side without
Rittal logo

Fig. 7:

Installing the standard filter mat

+Kte
If it becomes necessary to
change the direction of the
airflow (see 5.3 Changing the
direction of airflow, page 10),
the installation is reversed
accordingly.

8 IJspectiKJ aJd
IaiJteJaJce
RisG Kf eHectric shKcG!
The uJit is Hive
Switch Kff the pKwer suppHy
befKre KpeJiJg aJd taGe suit
abHe precautiKJs agaiJst it
beiJg accideJtaHHy switched
bacG KJ

The built-in, maintenance-free fan is mounted on a friction bearing (3237.xxx, 3238.xxx

and 3239.xxx) or ball bearing (3240.xxx,
3241.xxx, 3243.xxx to 3245.xxx), and is
protected against humidity and dust, and
equipped with a temperature monitor.
The life expectancy is at least 40,000 operating hours (L10, 40C). The fan-and-filter unit
is thus largely maintenance free.
From time to time, the components may
need to be cleaned using a vacuum
cleaner or compressed air if they
become visibly dirty.
Any stubborn, oily stains may be removed
using a non-flammable detergent, such as
degreaser.
CautiKJ!
RisG Kf fire!
+ever use fHaIIabHe Hiquids
fKr cHeaJiJg
Sequence of maintenance measures:
Check the level of dirt.
Filter soiling?
Replace the filter.
Fan membranes soiled?
Clean.
Check the noise generation of the fan.
Compressed air cleaning

9 StKrage aJd dispKsaH

CautiKJ!
RisG Kf daIage!
The faJ uJit Iust JKt be
stKred at teIperatures abKve
70aC Kr beHKw 30aC
Disposal can be performed at the Rittal
plant.
Please contact us for advice.

Rittal fan-and-filter unit assembly and operating instructions

11

E+

10 TechJicaH specificatiKJs
E+

10 TechJicaH specificatiKJs
Observe the pre-fuse as per the specifications on the rating plate

Observe the mains connection data

(voltage and frequency) as per the rating plate
UJit

*KdeH +K

FaJaJdfiHter uJit
RA) 7035

3237100

3237110 3237124 3238100 3238110 3238124

E*C faJaJdfiHter uJit

RA) 7035

3237600

3238600

Rated operating voltage

V
Hz

230, 1~,
50/60

115, 1~,
50/60

24 (DC)

230, 1~,
50/60

24 (DC)

Rated current max.

0.065/0.052 0.12/0.1

0.125

0.12/0.11 0.24/0.22 0.24

Power consumption

11/9

19/18

Pre-fuse T

115, 1~,
50/60

5.5

Dimensions
Width (B1) x height (H1)

mm

116.5 x 116.5

148.5 x 148.5

Required mounting cutout (B2 x H2)

mm

92 x 92

124 x 124

Depth (T1)

mm

16

Max. installation depth

(T2)

mm

43

Air throughput,
unimpeded airflow

m/h

20/25

Air throughput with outlet

filter including standard
filter mat

m/h

58.5
20

55/66

1 x 3237.200: 15/18

1 x 3238.200: 43/50

2 x 3238.200: 46/56

,utHet fiHter

3237200

3238200

E*C KutHet fiHter

3237060

3238060

Fan

Axial, self-starting
shaded pole motor

Noise pressure level

dB (A) 38/43

Operating temperature

-15...+55

Storage temperature

-30...+70

Protection category
(to IEC 60 529)

Tab. 2:

12

Technical specifications

55

Diagonal,
Axial,
Diagonal,
self-starting shaded
DC motor
DC motor
pole motor
38

IP 54 standard
IP 55 with hose-proof hood
IP 56 with hose-proof hood

46/49

46

IP 54 standard
IP 55 with hose-proof hood
IP 56 with hose-proof hood
Technical modifications reserved.

Rittal fan-and-filter unit assembly and operating instructions

10 TechJicaH specificatiKJs
UJit

*KdeH +K

FaJaJdfiHter uJit
RA) 7035

3239100

3239110

3239124

E*C faJaJdfiHter uJit

RA) 7035

3239600

Rated operating voltage

V
Hz

230, 1~,
50/60

115, 1~,
50/60

24 (DC)

Rated current max.

0.12/0.11

0.24/0.22

0.23

Power consumption

19/18

Pre-fuse T

E+

5.5

Dimensions
Width (B1) x height (H1)

mm

204 x 204

Required mounting
cut-out (B2 x H2)

mm

177 x 177

Depth (T1)

mm

24

Max. installation depth

(T2)

mm

90

Air throughput,
unimpeded airflow

m/h

105/120

Air throughput with outlet

filter including standard
filter mat

1 x 3239.200: 87/100
m/h

2 x 3239.200: 93/108
1 x 3240.200: 98/111

,utHet fiHter

3239200

E*C KutHet fiHter

3239060

Fan

Diagonal,
self-starting shaded pole motor

Noise pressure level

dB (A) 46/49

Operating temperature

-15...+55

Storage temperature

-30...+70

Protection category
(to IEC 60 529)

Tab. 3:

105

Diagonal,
DC motor
46

IP 54 standard
IP 55 with additional fine filter mat or hose-proof hood
IP 56 with hose-proof hood

Technical specifications

Rittal fan-and-filter unit assembly and operating instructions

Technical modifications reserved.

13

10 TechJicaH specificatiKJs
E+

UJit

*KdeH +K

FaJaJdfiHter uJit
RA) 7035

3240100 3240110 3240124

3241100 3241110 3241124

E*C faJaJdfiHter uJit

RA) 7035

3240600

3241600

Rated operating voltage

V
Hz

230, 1~,
50/60

24 (DC)

230, 1~,
50/60

24 (DC)

Rated current max.

0.21/0.19 0.42/0.38 0.43

0.26/0.24 0.52/0.48 0.8

Power consumption

35/34

10

40/42

Pre-fuse T

180

230/250

230

115, 1~,
50/60

115, 1~,
50/60

40/42

19

Dimensions
Width (B1) x
height (H1)

mm

255 x 255

Required mounting
cut-out (B2 x H2)

mm

224 x 224

Depth (T1)

mm

25

Max. installation depth

(T2)

mm

107

Air throughput,
unimpeded airflow

m/h

180/160

Air throughput with outlet

filter including standard
filter mat

m/h

1 x 3240.200: 138/121

1 x 3240.200: 183/205

2 x 3240.200: 165/140

2 x 3240.200: 203/230

1 x 3243.200: 165/140

1 x 3243.200: 203/230

,utHet fiHter

3240200

E*C KutHet fiHter

3240060

Fan

Diagonal,
self-starting shaded
pole motor

Noise pressure level

dB (A) 51/46

Operating temperature

-30...+55

Storage temperature

-30...+70

Protection category
(to IEC 60 529)

Tab. 4:

14

Technical specifications

Diagonal,
DC motor

Diagonal,
self-starting shaded
pole motor

Diagonal,
DC motor

51

54/56

54

IP 54 standard
IP 55 with additional fine filter mat or hose-proof hood
IP 56 with hose-proof hood
Technical modifications reserved.

Rittal fan-and-filter unit assembly and operating instructions

10 TechJicaH specificatiKJs
UJit

*KdeH +K

E+

FaJaJdfiHter
uJit
RA) 7035

3243.100 3243.110 3244.100 3244.110 3244.140

3245.500

3245.510

E*C faJaJd
fiHter uJit
RA) 7035

3243.600

3244.600

3245.600

230,
1~,
50/60

115,
1~,
50/60

400/460,
3~,
50/60

200240 100130
1~,
1~,
50/60
50/60

Rated operating
voltage

V
Hz

230,
1~,
50/60

115,
1~,
50/60

Rated current
max.

0.37/0.39 0.78/0.8

0.43/0.6

0.9/1.25

0.17/0.21 1.33

2.1

Power
consumption

70/87

75/90

95/135

100/145

93/140

165

165

Pre-fuse T

Motor
circuitbreaker

Dimensions
Width (B1) x
height (H1)

mm

323 x 323

Required
mounting cut-out
(B2 x H2)

mm

292 x 292

Depth (T1)

mm

25

Max. installation
depth (T2)

mm

118.5

130.5

130.5

Air throughput,
unimpeded airflow

m/h

550/600

700/770

900

1 x 3243.200:
465/510

1 x 3243.200:
544/587

1 x 3243.200:
680

2 x 3243.200:
508/548

2 x 3243.200:
614/662

2 x 3243.200:
820

Air throughput
with outlet filter
including standard filter mat

m/h

,utHet fiHter

3243200

E*C KutHet fiHter

3243060

Fan

Diagonal,
capacitor motor

Noise pressure
level

dB (A) 59/61

Operating
temperature

-30...+55

Storage
temperature

-30...+70

Protection
category
(to IEC 60 529)
Tab. 5:

Diagonal,
Diagonal,
rotary curEC motor
rent motor
65/66

67/70

72

IP 51 standard
IP 54 standard
IP 52 with additional
IP 55 with additional fine filter mat or hose-proof hood fine filter mat
IP 56 with hose-proof hood
IP 56 with hose-proof
hood

Technical specifications

Rittal fan-and-filter unit assembly and operating instructions

Technical modifications reserved.

15

11 CutKutdriHHiJg diIeJsiKJs
11 CutKutdriHHiJg
diIeJsiKJs

+Kte
From a certain wall thickness,
a slightly larger cut-out is
required (see the enclosed
drilling template).
B2

T2

H2

T1

H1

E+

B1

Fig. 8:

Cut-out dimensions

B = Width, T= Depth

*KdeH +K

B2 x H2 II

3237xxx

92 x 92

43

3238xxx

124 x 124

58.5

3239xxx

177 x 177

90

3240xxx

224 x 224

107

3241xxx

224 x 224

107

3243xxx

292 x 292

118.5

3244xxx

292 x 292

130.5

3245xxx

292 x 292

130.5

Tab. 6:

16

Cut-out dimensions

*KdeH +K

3237xxx

3.5

100.5

3238xxx

3.5

132.5

3239xxx

4.5

185

3240xxx

4.5

234

3241xxx

4.5

234

3243xxx

4.5

302

3244xxx

4.5

302

3245xxx

4.5

302

Tab. 7:

Fig. 9:

T2 II

II

F II

Drilling dimensions

Drilling pattern

Rittal fan-and-filter unit assembly and operating instructions

12 E*C faJKutHet fiHter

12 E*C faJKutHet fiHter

E+

To achieve EMC protection, the EMC fans

and EMC outlet filters should be snapped
into the mounting cut-out and screw-fastened using the screws supplied. Next, the
four contact foils should be stuck on allround between the fan-and-filter unit and
the inside of the enclosure as shown in the
following illustration.

Fig. 10:

EMC contact foils

+Kte
EMC protection can only be
guaranteed when using original
Rittal EMC filter media (Model
Nos. 3237.066, 3238.066,
3239.066, 3240.066, 3243.066).

Rittal fan-and-filter unit assembly and operating instructions

17

13 CKJJectiKJ diagraIs
E+

13 CKJJectiKJ diagraIs

M
1~

M
1~

N PE

3237.100/.110/.600
3238.100/.110/.600
3239.100/.110/.600

M
3~

N PE

3240.100/.110/.600
3241.100/.110/.600

Fig. 11:

18

PE

3243.100/.110/.600
3244.100/.110/.600

M
1~

M
1~

L1

L2 L3 PE

3244.140

3245.500/.510/.600
Details,
see page 19

M
24 V DC

24

3237.124
3238.124
3239.124
3240.124
3241.124

Connection diagrams

Rittal fan-and-filter unit assembly and operating instructions

13 CKJJectiKJ diagraIs
E+

For SK 3245 only!

1

Fan/motor

Interface

2
CON10

1
10 V
1V
<1 V

L
N

1 10 V
n = max.
n = min.
n=0

1.6 AT

CON11

AC 1

AC 2

PE
CON12

PE 1

+10 V
3
3

I max. = 1.1 mA

15 V

10 V/PWM
2
47 k

3
I max. = 10 mA

47 k

1 uF

GND
1

2
10 K

2
Speed
4

12 V
1
100 % PWM
10 % PWM
<10 % PWM

Fig. 12:

680 R

ZMM 47

n = max.
n = min.
n=0

Connection diagram 3245

1 Max. speed (as delivered)

2 Adjustable speed
3 Adjustable speed via PWM 1 10 kHz
4 Adjustable speed via potentiometer

+K

CKJJectiKJ

FuJctiKJAssigJIeJt

CON10

Power supply 200240 V AC, 5060 Hz

CON11

Neutral conductor

CON12

PE

PE conductor

GND

GND connection of the control interface

010 V/PWM

Control input 010 V or PWM, galvanically isolated, impedance 100 k

+10 V

Voltage output 10 V max. 1.1 mA, galvanically isolated, not short circuit-protected

Speed

Speed output Open Collector, 1 pulse per revolution, galvanically isolated

Tab. 8:

Explanations to fig. 12

Rittal fan-and-filter unit assembly and operating instructions

19

14 EC decHaratiKJ Kf cKJfKrIity
E+

14 EC decHaratiKJ Kf cKJfKrIity

20

Rittal fan-and-filter unit assembly and operating instructions

Enclosures
Power Distribution
Climate Control
IT Infrastructure
Software & Services

6th edition 11.2013 / ID no.: 328 628 / Drawing no.: A 4474200SK23

RITTAL GmbH & Co. KG

Postfach 1662 D-35726 Herborn
Phone +49(0)2772 505-0 Fax +49(0)2772 505-2319
E-mail: info@rittal.de www.rittal.com