Pressure Gauge

www.swagelok.
com
Pre ssure G auge s

Industr ial a nd Proce s s
PGI Se r ie s
40, 50, 63, 100, 115, and 160 mm (1 1/2, 2, 2 1/2, 4, 4 1/2 and 6 in.) dial sizes
Accuracy in accordance with ASME, EN, and JIS
Available with a variety of end connections, including Swagelok tube adapters
Center-back, lower-back, and lower mount configurations
Stainless steel and reinforced thermoplastic construction
Available unfilled or liquid filled
Industrial and Process Pressure Gauges
Contents
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Testing and Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Industrial Gauge Models

Stainless Steel Cases and Wetted Components
Swagelok Tube Adapters

Solve Alignment Problems . . . . . . . . . . . . . . . . . . . . . . . 2
Process Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Model Selection Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
B Model: General-Purpose Gauge

with Safety Glass Lens . . . . . . . . . . . . . . . . .
C Model: General-Purpose Gauge . . . . . . . . . . . . . . . . .
S Model: Solid-Front Safety Gauge . . . . . . . . . . . . . . . .
M Model: Miniature Gauge . . . . . . . . . . . . . . . . . . . . . . . 10

L Model: Low-Pressure Gauge . . . . . . . . . . . . . . . . . . . . 12
Process Gauge Model
Glass-Reinforced Thermoplastic Case and
Stainless Steel, Brass, or Alloy 400 Wetted Components
P Model: Industrial Process Gauge . . . . . . . . . . . . . . . . 14
Dial Range Designators . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Options and Accessories . . . . . . . . . . . . . . . . . . . . . . . . . 19
Features
Testing and Calibration
Monitor vacuum and positive system pressures up to
Every Swagelok industrial pressure gauge is factory calibrated

and pressure tested.
15000psi, 1000 bar, or 100 MPa

Manufactured in accordance with industry standards
Available with Swagelok tube adapter end connections
Swagelok Tube Adapters Solve Alignment Problems

Swagelok tube adapters can help eliminate difficult alignment problems
and can be used with any Swagelok tube fitting.
Typical Alignment Problem
When installing a gauge with a pipe fitting end connection,
it is often difficult to align the dial to the desired position
without damaging the gauge.
Swagelok Tube Adapters

Gauges with integral Swagelok tube adapters eliminate
alignment problems.
Installation Instructions
1. Insert the gauge with integral Swagelok tube adapter into
a Swagelok tube fitting.
2. Align the gauge dial to the desired position.
3. Install the fitting.
Swagelok tube adapters are to be used ONLY in
Swagelok tube fittings. Use in fittings made by other

manufacturers may result in leakage or slippage.
100
50
10
150
14
200
Process Connections
Connection
Maximum Pressure
Specification
Swagelok Tube Adapter

1/4 in. and 6 mm
10 000 psi, 600 bar,

60 MPa
3/8 in. and 10 mm
7500 psi, 500 bar,

50MPa
1/2 in. and 12 mm
6000 psi, 400 bar,

40MPa
1/8 in.
6000 psi, 400 bar,

40MPa
1/4 and 1/2 in.
15 000 psi, 1000 bar,

100 MPa
Male NPT
ASME B1.20.1
Male ISO Parallel Gauge Thread (EN)

G1/8B (EN)
6000 psi, 400 bar,

40MPa
G1/4B (EN)
G1/2B (EN)
15 000 psi, 1000 bar,

100 MPa
EN 837-1
EN 837-3
Male ISO Parallel Gauge Thread (JIS)

G1/4B (PF)
G1/2B (PF)
15 000 psi, 1000 bar,

100 MPa
JIS B7505
Male ISO Tapered Thread

R1/8 (PT)
6000 psi, 400 bar,

40MPa
R1/4 (PT)
R1/2 (PT)
15 000 psi, 1000 bar,

100 MPa
ISO 7/1
JIS B0203
G1/8B (EN), G1/4B (EN), and G1/2B (EN) are for use with Swagelok RG
adapter fittings.
G1/8B (PF), G1/4B (PF), and G1/2B (PF) are for use with Swagelok RJ
adapter fittings.
Model Selection Guide

Dial Range
Positive pressures:
0 to 10 psi,
400 mbar, or 50 kPa
Compound pressures:
Vacuum to 200 psi,
9 bar, or 1.5 MPa
Positive pressures:
0 to 10 000 psi,
600 bar, or 60 MPa
Compound pressures:
Vacuum to 200 psi,
9 bar, or 1.5 MPa
Positive pressures:
0 to 15 000 psi,
1000 bar, or 100 MPa
Dial Size
mm (in.)
63
(2 1/2)
100
(4)
40
(1 1/2)
50
(2)
63
(2 1/2)
100
(4)
160 (6)
Compound pressures:
Vacuum to 400 psi, 9 bar,
1.5 MPa, or 2500 kPa
Positive pressures:
0 to 15 000 psi, 1000bar,
100 MPa, or 100 000 kPa
Solid
Front
Liquid
Fillable
LBM
CBM
LM
Yes
Yes
Yes
Yes
Yes
1.5 % of span
ASME B40.100 Grade B,
EN 837-1 Class 1.6,
JIS B7505 Class 1.6
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
1 % of span
ASME B40.100
Grade1A,
EN 837-1 Class 1.0
JIS B7505 Class 1.0
Yes
Yes
Yes
Yes
Yes
Accuracy
1.5 % of span
ASME B40.100 Grade B,
EN 837-3 Class 1.6,
JIS B7505 Class 1.6
2.5 % of span
ASME B40.100 Grade C,
EN 837-1 Class 2.5,
JIS B7505 Class 2.5
115
(4 1/2)
160
Model
L
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
0.5 % of span
ASME B40.100 Grade 2A
(6)
Configurations: LBM = lower-back mount
Configurations
Adjustable
Pointer
CBM = center-back mount

LM = lower mount.
Liquid-fillable model available in lower mount configuration only.
Glycerin- and silicone-filled gauges cannot be used

where strong oxidizing agents are present.
B Model: General-Purpose
Stainless Steel Gauge
with Safety Glass Lens
Features
63, 100, and 160 mm (2 1/2, 4, and 6 in.) dial sizes are
available.
Bayonet ring allows easy access to pointer.
Lens is constructed of safety glass for additional protection.
Design is liquid fillable.
Technical Data
Dial Ranges
End Connections
Operating Temperature
Compound Gauges
63 mm (2 1/2 in.) Dial Size
Ambient
Vacuum to 0 psi through vacuum to
1/4 and 3/8 in.; 6 and 10 mm
Unfilled: 40 to 140F (40 to 60C)
200psi
Vacuum to 0 bar through vacuum to
9bar
Vacuum to 0 MPa through vacuum to
1.5MPa
Positive-Pressure Gauges
0 to 15 psi through 0 to 15 000 psi
0 to 1 bar through 0 to 1000 bar
Swagelok tube adapter

1/4 in. male NPT
G1/4B (EN)
G1/4B (PF)
R1/4 (PT)
100 mm (4 in.) Dial Size

1/2 in. and 12 mm Swagelok tube
adapter
Glycerin-filled: 4 to 140F (20 to
60C)
Low-temperature glycerin-filled:
29to 140F (34 to 60C)

Silicone-filled: 40 to 140F (40 to
60C)
Media
Unfilled: 392F (200C) maximum
Liquid-filled: 212F (100C) maximum
0 to 0.1 MPa through 0 to 100 MPa
1/4 and 1/2 in. male NPT
Accuracy
G1/2B (EN)
Temperature Error
63 mm (2 1/2 in.): 1.5 % of span
G1/2B (PF)
0.4 % for every 18F (10C)

temperature change from 68F (20C)
(ASME B40.100 Grade B, EN 837-1

Class 1.6, JIS B7505 Class 1.6)
100 and 160 mm (4 and 6 in.):
1.0% of span (ASME B40.100

Grade1A, EN837-1 Class 1.0,
JISB7505 Class1.0)
R1/2 (PT)

1/2 in. male NPT
G1/2B (EN)
G1/2B (PF)
Configurations
R1/2 (PT)
63 mm (2 1/2 in.): center-back and
Weather Protection
lower mount
100 and 160 mm (4 and 6 in.): lower-
back and lower mount
Weather-tight (Nema 4X/IP65)
Materials of Construction
Component
End connection
Bourdon tube
Material
316 SS
Case
304 SS
Fill fluid
(if ordered)
Glycerin, lowtemperature glycerin,

or silicone
Movement
Stainless steel
Lens
Laminated safety
glass
Lens gasket
Buna N
Dial
Pointer
Aluminum
Wetted components listed in italics.
See page 19 for options and

accessories for field installation.
Dimensions
Dial Size
mm (in.)
Dimensions are for reference only and

are subject to change.
End Connection
Size
Lower Mount
C
1/4 in.
63
(2 1/2)
Center-Back
Mount
Lower-Back
Mount
160
(6)
2.26 (57.3)
2.39 (60.8)
2.09 (53.0)
2.24 (57.0)
1/4 in.
3.15 (80.0)
2.45
2.39
2.45
3.27
3.60 (91.4)
3.44 (87.4)
3.43 (87.0)
3.27 (83.0)
1/2 in.
Male NPT
Swagelok tube
adapter
Male NPT
G1/2B (EN)
G1/2B (PF)
R1/2 (PT)
Swagelok tube
adapter
Male NPT
G1/2B (EN)
1/2 in.
G1/2B (PF)
R1/2 (PT)
12 mm
2.31 (58.8)
2.26 (57.3)
2.31 (58.8)
(4)
Male NPT
G1/4B (EN)
G1/4B (PF)
R1/4 (PT)
Dimensions, in. (mm)

A
3/8 in.
Swagelok tube
6 mm
adapter
10 mm
100
Type
Swagelok tube
adapter
1.30
0.39
(33.0)
(10.0)
(62.3)
(60.8)
(62.3)
(83.0)
1.97
1.18
(50.0)
(30.0)
0.63
(16.0)
3.60 (91.4)
3.44 (87.4)
4.65 (118)
3.27 (83.0)
1.97
(50.0)
1.97
(50.0)
B is 3.90 in. (99.0 mm) and C is 2.60 in. (66.0 mm) for gauges with lower-back mount and pressure
ratings of 1500 psi, 10 MPa, 100bar or higher.
Ordering Information
Build a B model gauge ordering number by combining the designators as shown below. List option designators alphabetically.
PGI - 63B - PG100 - L AQ X - ABJ

Product Function and Type
Pressure gauge, industrial
Dial Size and Model

63B = 63 mm (2 1/2 in.) dial
100B = 100 mm (4 in.) dial
160B = 160 mm (6 in.) dial
Dial Range
See page 16 and 17.
Process Connection Location

L = Lower mount (all dial sizes)
C =Center-back mount (63 mm [2 1/2 in.]
dial size only)
B =Lower-back mount (100 and 160 mm
[4 and 6 in.] dial sizes only)
Options (see page 19)

A = ASME B40.100 levelIV cleaning
B = Certificate of calibration
E = Material certification
F = Panel-mount clamp
G = Front flange
H = Rear flange
I = Maximum indicating pointer
J = Adjustable pointer
N = Orifice (0.023 in. [0.58 mm])
Available for unfilled gauges only.
Not available in lower mount gauge configuration.
Not available with adjustable pointer; not available
with dial range maximums lower than 54 psi
(3.7bar, 0.37 MPa).
Not available with maximum indicating pointer.
Liquid Fill Fluid (see page 19)

X = Unfilled
1 = Glycerin
2 = Low-temperature glycerin
3 = Silicone
Fitting Size and Type

AQ = 1/4 in. Swagelok tube adapter
BG = 3/8 in. Swagelok tube adapter
AS = 6 mm Swagelok tube adapter
BH = 10 mm Swagelok tube adapter
AO = 1/4 in. male NPT
AV = G1/4B (EN)
AX = G1/4B (PF)
BD = R1/4 (PT)

AR = 1/2 in. Swagelok tube adapter
AT = 12 mm Swagelok tube adapter
AP = 1/2 in. male NPT
AW = G1/2B (EN)
AZ = G1/2B (PF)
BE = R1/2 (PT)

AW = G1/2B (EN)
AZ = G1/2B (PF)
BE = R1/2 (PT)
C Model: General-Purpose
Stainless Steel Gauge
Features
63 and 100 mm (2 1/2 and 4 in.) dial sizes are available.
Crimped ring provides a permanent seal of gauge case
to lens.
Lens is constructed of clear polycarbonate.
Technical Data
Dial Ranges
Configurations
Compound Gauges
63 mm (2 1/2 in.): center-back and
Ambient
200psi
9bar
1.5MPa
Accuracy
63 mm (2 1/2 in.): 1.5 % of span

100 mm (4 in.): 1.0 % of span
(ASME B40.100 Grade 1A, EN 837-1

lower mount
100 mm (4 in.): lower-back and lower
mount
End Connections
1/4 and 3/8 in.; 6 and 10 mm

1/4 in. male NPT

adapter

60C)
29to 140F (34 to 60C)

60C)
Media
212F (100C) maximum
Temperature Error
Weather Protection
Component
End connection
Bourdon tube
Material
316 SS
Case
304 SS
Fill fluid
(if ordered)

or silicone
Movement
Stainless steel
Lens
Polycarbonate
Lens gasket
Buna N
Dial
Pointer
Aluminum

Dimensions
Dimensions are for reference only and are subject to change.
Lower Mount
C
Center-Back
Mount
Lower-Back
Mount
Dial Size
mm (in.)
63
(2 1/2)
100
End Connection
Size
Type
Swagelok tube
adapter
1/4 in.
Male NPT
3/8 in.
Swagelok tube
6 mm
adapter
10 mm
1/4 in.
Male NPT
1/2 in.
(4)
12 mm
Swagelok tube
adapter
Male NPT
Swagelok tube
adapter

A
2.22 (56.3)
2.37 (60.3)
2.09 (53.0)
2.28 (57.8)
2.22 (56.3)
2.28 (57.8)
3.15 (80.0)
2.24 (57.0)
2.43 (61.8)
2.37 (60.3)
2.43 (61.8)
3.27 (83.0)
3.64 (92.4)
3.48 (88.4)
3.43 (87.0)
3.27 (83.0)
3.64 (92.4)
3.48 (88.4)
1.30
(33.0)
0.39
(10.0)
1.97
0.63
1.18
(50.0)
(16.0)
(30.0)
1.10 (28.0) for center-back mount.
Build a C model gauge ordering number by combining the designators as shown below. List option designators alphabetically.
PGI - 63C - PG100 - L AQ X - ABH


G = Front flange
H = Rear flange
N = Orifice (0.023 in. [0.58 mm])
Dial Size and Model

63C = 63 mm (2 1/2 in.) dial
100C = 100 mm (4 in.) dial
Dial Range
See page 16 and 17.

C =Center-back mount (63 mm [21/2in.]
dial size only)
B =Lower-back mount (100 mm [4 in.]
dial size only)


Not available in lower mount gauge
configuration.
Not available with dial range maximums

lower than 54 psi (3.7bar, 0.37 MPa).

X = Unfilled
1 = Glycerin
3 = Silicone
S Model: Solid-Front Stainless

Steel Safety Gauge
Features
Lower mount configuration is liquid fillable.
Solid front and blowout back for severe service.
Design meets safety requirements of ASME B40.100
and EN 837-1.
Technical Data
Dial Ranges
Configurations
Compound Gauges
Lower-back and lower mount
Ambient
200psi
9bar
1.5MPa
Accuracy
63 mm (2 1/2 in.): 1.5 % of span

100 mm (4 in.): 1.0 % of span
(ASME B40.100 Grade 1A, EN 837-1

End Connections
1/4 and 3/8 in.; 6 and 10 mm

1/4 in. male NPT
G1/4B (EN)
G1/4B (PF)
R1/4 (PT)

adapter
G1/2B (EN)
G1/2B (PF)
R1/2 (PT)
Weather Protection

60C)
29to 140F (34 to 60C)

60C)
Media
Unfilled: 392F (200C) maximum
Liquid-filled: 212F (100C) maximum
Temperature Error
Component
End connection
Bourdon tube
Material
316 SS
Case
304 SS
Fill fluid
(if ordered)

or silicone
Movement
Stainless steel
Lens
Laminated safety
glass
Lens gasket
Buna N
Dial
Pointer
Aluminum

Dimensions
Dial Size
mm (in.)

End Connection
Size
Lower Mount
C
1/4 in.
63
(2 1/2)
Lower-Back
Mount
Male NPT
G1/4B (EN)
G1/4B (PF)
R1/4 (PT)

A
2.26 (57.3)
2.59 (65.8)
2.13 (54.0)
2.48 (63.0)
3/8 in.
Swagelok tube
6 mm
adapter
10 mm
2.31 (58.8)
2.26 (57.3)
2.31 (58.8)
1/4 in.
3.15 (80.0)
2.65 (67.3)
2.59 (65.8)
2.65 (67.3)
3.39 (86.0)
3.44 (87.4)
3.83 (97.4)
Male NPT
G1/2B (EN)
G1/2B (PF)
R1/2 (PT)
3.43 (87.0)
3.66 (93.0)
Swagelok tube
adapter
3.44 (87.4)
3.83 (97.4)
100
Type
Swagelok tube
adapter
1/2 in.
(4)
12 mm
Male NPT
Swagelok tube
adapter
1.65
0.71
0.71
(42.0)
(18.0)
(18.0)
2.28
0.94
1.18
(58.0)
(24.0)
(30.0)
Build a S model gauge ordering number by combining the designators as shown below. List option designators alphabetically.
PGI - 63S - PG100 - L AQ X - ABJ

Dial Size and Model

63S = 63 mm (2 1/2 in.) dial
100S = 100 mm (4 in.) dial

G = Front flange
J = Adjustable pointer
N = Orifice (0.023 in. [0.58 mm])
configuration.
Dial Range
See page 16 and 17.

L = Lower mount
B = Lower-back mount
Not available with adjustable pointer; not
available with dial range maximums lower

than 54 psi (3.7bar, 0.37 MPa).
Not available with maximum indicating
pointer.

(Lower mount configuration only)
X = Unfilled
1 = Glycerin
3 = Silicone

AV = G1/4B (EN)
AX = G1/4B (PF)
BD = R1/4 (PT)

AW = G1/2B (EN)
AZ = G1/2B (PF)
BE = R1/2 (PT)
10
M Model: Stainless Steel Miniature Gauge

Features
Miniature size allows placement in compact spaces.
Snap-in lens saves space when compared to twist-on lens.
Technical Data
Dial Ranges
Configurations
Compound Gauges
Center-back and lower mount
Ambient
200psi
9bar
1.5MPa
End Connections
1/8 in. and 1/4 in. male NPT
Media
G1/8B (EN) and G1/4B (EN)
212F (100C) maximum
R1/8 (PT) and R1/4 (PT)
Temperature Error
1/4 and 3/8 in.; 6 and 10 mm


G1/4B (PF)
Weather Protection
Weather-tight (Nema 3/IP54)
Accuracy
2.5 % of span (ASME B40.100
GradeC, EN 837-1 Class 2.5, JIS
B7505 Class2.5)
40 to 140F (40 to 60C)
Component
End connection
Bourdon tube
Material
316 SS titanium alloy
Case
304 SS
Movement
Stainless steel
Lens
Polycarbonate
Dial
Pointer
Aluminum

Dimensions
Dial Size
mm (in.)

Lower Mount
C
40
(1 1/2)
A
End Connection
Size
Type
Male NPT
1/8 in.
G1/8B (EN)
R1/8 (PT)
Swagelok tube
adapter
1/4 in.
Male NPT
G1/4B (EN)
G1/4B (PF)
R1/4 (PT)
3/8 in.
Swagelok tube
6 mm
adapter
10 mm
11

A
1.42 (36.1)
1.95 (49.5)
1.67 (42.3)
2.20 (55.8)
1.54 (39.0)
2.07 (52.6)
1.73 (43.9)
1.67 (42.3)
1.73 (43.9)
2.26 (57.4)
2.20 (55.8)
2.26 (57.4)
1.73 (43.9)
1.99 (50.5)
1.98 (50.3)
2.24 (56.8)
1.85
1.85
1.97
1.85
2.04
2.11
2.11
2.22
2.11
2.30
2.24
2.30
0.98 (25.0)
0.35 (9.0)
0.98 (25.0)
0.35 (9.0)
Male NPT
Center-Back
Mount
1/8 in.
G1/8B (EN)
R1/8 (PT)
Swagelok tube
adapter
50
(2)
1/4 in.
Male NPT
G1/4B (EN)
G1/4B (PF)
R1/4 (PT)
3/8 in.
Swagelok tube
6 mm
adapter
10 mm
(47.0)
(47.0)
(50.0)
(47.0)
(51.8)
1.98 (50.3)
2.04 (51.8)
(53.6)
(53.6)
(56.4)
(53.6)
(58.3)
(56.8)
(58.3)
2.22 in. (56.3 mm) for gauges with front flange.
Build an M model gauge ordering number by combining the designators as shown below. List option designators alphabetically.
PGI - 50M - PG100 - L AQ X - ABE
Dial Range

G = Front flange
L = Glass lens with friction ring
N = Orifice (0.023 in. [0.58 mm])
See page 16 and 17.
Available factory installed only. Not available

Dial Size and Model

40M = 40 mm (1 1/2 in.) dial
50M = 50 mm (2 in.) dial
in lower mount configuration.
Liquid Fill FluidNot Available
C = Center-back mount
L = Lower mount
Unfilled

AN = 1/8 in. male NPT
AU = G1/8B (EN)
AV = G1/4B (EN)
AX = G1/4B (PF)
BC = R1/8 (PT)
BD = R1/4 (PT)
12
L Model: Stainless Steel

Low-Pressure Gauge
Features
Diaphragm capsule design offers low-pressure
measurement capability.
A zero adjustment screw is on the dial.
Lens is constructed of safety glass for additional protection.
Technical Data
Dial Ranges
Configurations
63 mm (2 1/2 in.): lower mount
Ambient
0 to 15 in. H2O through 0 to
100 mm (4 in.): lower-back and lower
40 to 140F (40 to 60C)
200in.H2O
0 to 5 psi through 0 to 10 psi

0 to 40 mbar through 0 to 400 mbar
0 to 4 kPa through 0 to 50 kPa
Accuracy
1.5 % of span (ASME B40.100 Grade
B, EN 837-3 Class 1.6, JIS B7505

Class1.6)
mount
Media
End Connections
212F (100C) maximum
Temperature Error
1/4 and 3/8 in.; 6 and 10 mm


1/4 in. male NPT
G1/4B (EN)
G1/4B (PF)
R1/4 (PT)

adapter
G1/2B (EN)
G1/2B (PF)
R1/2 (PT)
Weather Protection
Component
End connection
Diaphragm capsule
Material
316 SS
Case
304 SS
Movement
Stainless steel
Lens
Laminated safety
glass
Dial
Pointer
Aluminum
Weather-tight (Nema 3/IP54)

Dimensions
End Connection
Dial Size
mm (in.)

Size
Lower Mount
C
1/4 in.
63
(2 1/2)
Male NPT
G1/4B (EN)
G1/4B (PF)
R1/4 (PT)

A
2.05 (52.0)
2.31 (58.8)
2.26 (57.3)
2.31 (58.8)
1/4 in.
3.15 (80.0)
3.27 (83.0)
3.60 (91.4)
3.44 (87.4)
Male NPT
G1/2B (EN)
G1/2B (PF)
R1/2 (PT)
3.43 (87.0)
3.27 (83.0)
Swagelok tube
adapter
3.60 (91.4)
3.44 (87.4)
100
1/2 in.
(4)
12 mm
Male NPT
Swagelok tube
adapter
1.65
0.35
(42.0)
(9.0)
2.26 (57.3)
3/8 in.
Swagelok tube
6 mm
adapter
10 mm
Lower-Back
Mount
Type
Swagelok tube
adapter
13
2.28
0.63
1.18
(58.0)
(16.0)
(30.0)
Build an L model gauge ordering number by combining the designators as shown below. List option designators alphabetically.
PGI - 63L - IG30 - L AQ X - ABH


G = Front flange
H = Rear flange
N = Orifice (0.023 in. [0.58 mm])
Dial Size and Model

63L = 63 mm (2 1/2 in.) dial
100L = 100 mm (4 in.) dial
Dial Range
See page 16.
configuration.
Available for 100 mm (4 in.) dial size only.

Not available with dial range maximums
lower than 1.5 psi (103mbar, 10.3 kPa,
41.5in. H2O).

B = Lower-back mount (100 mm [4 in.] dial size only)
Liquid Fill FluidNot Available

Unfilled

AV = G1/4B (EN)
AX = G1/4B (PF)
BD = R1/4 (PT)

AW = G1/2B (EN)
AZ = G1/2B (PF)
BE = R1/2 (PT)
14
P Model: Reinforced Thermoplastic

Industrial Process Gauge
Features
Solid front and blowout back for severe service.
Design meets safety requirements of ASME B40.100.
Adjustable pointer is standard.
Threaded cover ring allows easy access to pointer.
Lens is constructed of clear acrylic plastic.
Technical Data
Dial Ranges
Configurations
Compound Gauges
Lower-back mount and lower mount
Ambient
400 psi
9bar
1.5MPa
Vacuum to 0 kPa through vacuum to
2500 kPa
End Connections
1/2 in. Swagelok tube adapter
0.5 % of span (ASME B40.100

Grade2A)
60C)
212F (100C) maximum
Weather resistant (Nema 3/IP54)
Accuracy
1/2 in. male NPT
0 to 60 kPa through 0 to 100 000 kPa
60C)
Media
Weather Protection
dry case
liquid-fillable case
Maximum media temperature for the
brass process gauge is 140F (60C)
Temperature Error
Component
End connection
Bourdon tube
Material
316 SS
Case
Black glassreinforced
thermoplastic
Fill fluid
(if ordered)

or silicone
Movement
Stainless steel
Lens
Acrylic
Lens gasket
Buna N
Dial
Pointer
Aluminum

115 mm (4 1/2 in.) P model gauges are
available in alloy 400 materials; lower mount
gauges are also available in brass.

15
Dimensions
Dimensions are for reference only and are subject to change.
Lower Mount
Lower-Back Mount
B
E
A
Dial Size
mm (in.)
End Connection
Size
1/2 in.
115
(4 1/2)
(6)

A
4.27 (108)
4.95 (126)
3.82 (97.0) 4.50 (114) 3.31 (84.0)
1/4 in.
1/2 in.
160
Type
Swagelok
tube adapter
Male NPT
1/2 in.
4.06 (103)
4.74 (120)
4.82 (123)
4.86 (123) 3.46 (88.0)
1.57 (40.0) 1.12 (28.5)
Build a P model gauge ordering number by combining the designators as shown below. List option designators alphabetically.
PGI - 115P - OG160 - L AR X - AB J

Pointer
Standard adjustable pointer
Dial Size and Model
115P = 115 mm (4 1/2 in.) dial

160P = 160 mm (6 in.) dial

K = Safety glass
M = Liquid-fill membrane
N = Orifice (0.023 in. [0.58 mm])
Q = Brass (wetted components)
R = Alloy 400 (wetted components)
S = Mark pointer
Dial Range
See page 16, 17, and 18.

L = Lower mount
B = Lower-back mount

BT = 1
/2 in. long Swagelok tube adapter
For use with female Swagelok end connections.


configuration.
Available on 115 mm (4 1/2 in.) dial size only.
Not available on gauges with maximum
indicating or mark pointer.
Required for lower-back mount
configuration with liquid fill.
Available on 115 mm (4 1/2 in.) dial size with
lower mount only.

X = Unfilled
1 = Glycerin
3 = Silicone
16
Dial Range Designators

The selected dial range should be approximately two times the system working
pressure, and the system working pressure should be in the middle half (25 to
75%) of the dial range. Contact your authorized Swagelok sales and service
representative if the system working pressure will exceed 75 % of the dial range.
Maximum pressure is limited by the end connection and materials of
construction of wetted components.
Not all dial ranges and end connections are available on all models.
L Model
L Model
Dial Range, psi

(primary scale: psi; secondary scale: bar)
Minimum
0
Maximum
Designator
Dial Range, in. H2O

(primary scale: in. H2O; no secondary scale)
Minimum
Maximum
Designator
Maximum
Designator
PG5
15
IG15
40
FG40
PG10
20
IG20
60
FG60
30
IG30
100
FG100
60
IG60
160
FG160
100
IG100
250
FG250
200
IG200
400
FG400
Maximum
RG4
RG5
RG7
Dial Range, bar

(primary scale: bar; secondary scale: psi)
10
RG10
Minimum
15
RG15
BC0
20
RG20
0.6
BC.6
1.5
BC1.5
BC3
BC9
Dial Range, kPa

(primary scale: kPa; no secondary scale)
BG1
1.6
BG1.6
Minimum
2.5
BG2.5
50
RG50
B, C, M, S, and P Models
Vacuum
1 bar
L Model
Maximum
Designator
Minimum
Dial Range, kPa

(primary scale: kPa;
secondary scale mm H2O)
Dial Range, mbar

(primary scale: mbar; no secondary scale)
10
L Model
Minimum
L Model
Designator
Maximum
Designator
JG4
BG4
JG5
BG6
JG7
10
BG10
10
JG10
16
BG16
15
JG15
25
BG25
20
JG20
40
BG40
50
JG50
60
BG60
100
BG100
160
BG160
250
BG250
400
BG400
600
BG600
1000
BG1000
Dial Range, MPa
(primary scale: MPa;
secondary scale: kgf/cm2)
Minimum
Vacuum
0.1 MPa
Maximum
Designator
LC0
0.06
LC.06
0.15
LC.15
0.30
LC.3
0.50
LC.5
0.90
LC.9
1.5
LC1.5
0.1
LG.1
0.16
LG.16
0.25
LG.25
0.40
LG.4
0.60
LG.6
LG1
1.6
LG1.6
2.5
LG2.5
LG4
LG6
10
LG10
16
LG16
25
LG25
40
LG40
60
LG60
100
LG100
17

pressure, and the system working pressure should be in the middle half (25 to 75%)
of the dial range. Contact your authorized Swagelok representative if the system
working pressure will exceed 75 % of the dial range.
Dial Range, MPa
(primary scale: MPa; no secondary scale)
Minimum
Vacuum
0.1 MPa
Maximum
Designator
MC0
0.06
MC.06
0.15
MC.15
0.30
MC.3
0.50
MC.5
0.90
1.5
Dial Range, psi
(primary scale: psi; secondary scale: kPa)
Minimum
Maximum
Designator
Dial Range, psi
(primary scale: psi; secondary scale: bar)
Minimum
Maximum
Designator
OC0
PC0
15
OC15
15
PC15
30
OC30
30
PC30
60
OC60
60
PC60
100
OC100
100
PC100
MC.9
160
OC160
160
PC160
MC1.5
200
OC200
200
PC200
0.1
MG.1
15
OG15
15
PG15
0.16
MG.16
30
OG30
30
PG30
0.25
MG.25
60
OG60
60
PG60
0.40
MG.4
100
OG100
100
PG100
0.60
MG.6
160
OG160
160
PG160
MG1
200
OG200
200
PG200
1.6
MG1.6
300
OG300
300
PG300
2.5
MG2.5
400
OG400
400
PG400
MG4
500
OG500
500
PG500
600
OG600
600
PG600
800
OG800
800
PG800
Vacuum
30 in. Hg
Vacuum
30 in. Hg
MG6
10
MG10
16
MG16
1 000
OG1000
1 000
PG1000
25
MG25
1 500
OG1500
1 500
PG1500
40
MG40
2 000
OG2000
2 000
PG2000
60
MG60
3 000
OG3000
3 000
PG3000
100
MG100
4 000
OG4000
4 000
PG4000
5 000
OG5000
5 000
PG5000
6 000
OG6000
6 000
PG6000
10 000
OG10K
10 000
PG10K
15 000
OG15K
15 000
PG15K
18

pressure, and the system working pressure should be in the middle half (25 to 75%)
of the dial range. Contact your authorized Swagelok representative if the system
working pressure will exceed 75 % of the dial range.
P Model
P Model
P Model
Dial Range, KPa

(primary scale: KPa; no secondary scale)
Dial Range, psi

(primary scale: psi; no secondary scale)
Minimum
Minimum
Vacuum
100 KPa
Maximum
Designator
Maximum
Designator
Dial Range, psi

(primary scale: psi; secondary scale kgf/cm2)
Minimum
Maximum
Designator
JC0
NC0
QC0
60
JC60
15
NC15
15
QC15
150
JC150
30
NC30
30
QC30
300
JC300
60
NC60
60
QC60
500
JC500
100
NC100
100
QC100
900
JC900
160
NC160
160
QC160
1 500
JC1500
200
NC200
200
QC200
2 500
Vacuum
30 in. Hg
Vacuum
30 in. Hg
JC2500
300
NC300
300
QC300
60
JG60
400
NC400
400
QC400
100
JG100
15
NG15
15
QG15
160
JG160
30
NG30
30
QG30
250
JG250
60
NG60
60
QG60
400
JG400
100
NG100
100
QG100
600
JG600
160
NG160
160
QG160
1 000
JG1000
200
NG200
200
QG200
1 600
JG1600
300
NG300
300
QG300
2 500
JG2500
400
NG400
400
QG400
4 000
JG4000
500
NG500
500
QG500
6 000
JG6000
600
NG600
600
QG600
10 000
JG10K
800
NG800
800
QG800
16 000
JG16K
1 000
NG1000
1 000
QG1000
25 000
JG25K
1 500
NG1500
1 500
QG1500
40 000
JG40K
2 000
NG2000
2 000
QG2000
60 000
JG60K
3 000
NG3000
3 000
QG3000
100 000
JG100K
4 000
NG4000
4 000
QG4000
5 000
NG5000
5 000
QG5000
6 000
NG6000
6 000
QG6000
10 000
NG10K
10 000
QG10K
15 000
NG15K
15 000
QG15K
Options and Accessories

Factory-installed options are specified in gauge ordering
numbers, as shown in Ordering Information for each gauge
model. Some items are available only as factory-installed
options; others are available for field installation, as described
below.
Adjustable Pointers
Gauges are available with adjustable pointers that allow
resetting to zero. Adjustable pointers are standard for all P
model gauges and are optional for B and S model gauges.
Orifices
Orifices are used to restrict flow, reducing the immediate
effect of pulsations and pressure spikes. All Swagelok
industrial and process gauges are available with orifices as
factory-installed options.
Threaded orifices (0.023 in. [0.58 mm] inside diameter)
are available for P model industrial process gauges as
P Model Threaded Orifice Kits

Orifice Material
Ordering Number
Liquid Fill
Liquid-filled gauges enhance the reliability and integrity
of the measuring system for long periods under extreme
operating conditions by dampening vibration and
lubricating the gauge movement. B, C, S, and P model
gauges are available liquid filled.
Because the type of liquid used to fill the gauge may
vary with the application, Swagelok offers glycerin,
low-temperature glycerin, and silicone. It is important
to choose the proper fill liquid based on the operating
temperature and pressure.
Ambient Operating Temperature

Temperature
F (C)
Fill Fluid
40 to 140 (40 to 60)
Unfilled
4 to 140 (20 to 60)
Glycerin
29 to 140 (34 to 60)
Low-temperature glycerin
40 to 140 (40 to 60)
Silicone
PGI-P-ORIFICE
Operating Pressure (Dial Range)
Brass
PGI-P-ORIFICE-Q
Alloy 400
PGI-P-ORIFICE-R
If the dial range selected is equal to or below 60 psi,

4bar, 0.4MPa, or equivalent, liquid-filled gauges must
use low-temperature glycerin or silicone fill liquid to
ensure fastest response and gauge accuracy.
Stainless steel
Special Cleaning
Special cleaning is available as an option for unfilled gauges.
Internal components are cleaned in accordance with
ASMEB40.100, Section 5, which states that the gauge shall
be free of visually detectable moisture and foreign matter
(chips, slivers, weld slag or splatter, shop soil, greases,
oils, or other contaminants)that could be mechanically
detrimental to proper function of the gauge. The gauge is
then capped and bagged to maintain cleanliness.
Certificates of Calibration
This option provides the user with a calibration sheet and a
serial-numbered gauge that has been calibrated with a gauge
traceable to DKD for gauges manufactured in Germany or
to NIST for gauges manufactured in the U.S. Certificates of
calibration are available for all Swagelok gauges.
Material Certifications
This option provides the user with a General Material
Certificate of Compliance, EN102042.2, stating that the
gauges were manufactured from material purchased and
certified as being in accordance with the specifications listed
in this catalog. Material certifications are available for B, C, S,
M, and L model gauges.
In addition, if a maximum indicating pointer is selected

in a liquid-filled gauge, the fill liquid should be lowtemperature glycerin or silicone.
Glycerin- and silicone-filled gauges cannot be
used where strong oxidizing agents are present.
Glycerin and low-temperature glycerin fill liquid are

available as accessories for field installation.
Fill Liquid
Glycerin
Size
8 oz (236 mL)
squirt bottle
1 gal (3.8 L) bottle
Low-temperature
glycerin
8 oz (236 mL)
squirt bottle
1 gal (3.8 L) bottle
Ordering Number
PGI-GLY-8
PGI-GLY-128
PGI-GLY-86/14-8
PGI-GLY-86/14-128
19
20

Panel-Mount Clamps
Rear Flanges
Stainless steel panel-mount clamps are available for flush

mounting Swagelok industrial gauges. The panel-mount
clamp is easily installed on the gauge. This option is not
available on lower mount or S model gauges. Panel-mount
clamps on M model gauges must be factory installed and are
available as accessories for field installation on B, C, L, and P
model gauges.
Stainless steel rear flanges are available for mounting on the

front of the panel. This option is not available on M, S, and
P model gauges. Rear flanges are available factory installed
on B, C, and L model gauges and as accessories for field
installation.
Panel-Mount Clamp Kits

Gauge Model
B model
63 mm (2 1/2 in.) size
C model
63 mm (2 1/2 in.) size
B, C, and L models
100 mm (4 in.) size
P model
115 mm (4 1/2 in.) size
Ordering Number
B, C, and L Model Rear Flange Kits

Gauge Size
Ordering Number
63 mm (2 1/2 in.)
PGI-63BCL-RF
100 mm (4 in.)
PGI-100BCL-RF
PGI-63B-PMC
PGI-63C-PMC
PGI-100BCL-PMC
PGI-P-115-PMC
Front Flanges
Maximum Indicating Pointers

Maximum indicating pointers
(MIP), available for S, B, C, L, and
P models, identify pressure spikes
in a system and are helpful during
system startup and troubleshooting.
The MIP adds an additional 1 %
error to the gauge because of the
increased load on the bourdon tube.
This option must be factory installed
on C model gauges and is available
for field installation on S, B, L, and P model gauges.
Maximum Indicating Pointer Kits

Gauge Model
S, B, and L
63 mm (2 1/2 in.) size
Polished stainless steel front flanges are available for flush

panel mounting of Swagelok industrial gauges. This option is
not available on lower mount or P model gauges and must be
factory installed on C and M model gauges.
S, B, and L Model Front Flange Kits

Gauge Size
Ordering Number
63 mm (2 1/2 in.)
PGI-63SBL-FF
100 mm (4 in.)
PGI-100SBL-FF
S, B, and L
100 mm (4 in.) size
P
115 mm (4 1/2 in.) size
Ordering Number
PGI-63-MIP-SG
PGI-100-MIP-SG
PGI-P-115-MIP-A

Coil Steam Siphons
Positionable Gauge Adapters
Siphons protect pressure instruments in live steam service

or other high-temperature vapor applications. The vapor
condenses inside the coil of the siphon, preventing the hightemperature vapors from reaching the sensing element of
the pressure instrument. Siphons are available in carbon and
stainless steel.
Features
Coil Steam Siphon Kits

Material
End
Connection
Positionable gauge adapter allows 360 orientation of

Wall
Schedule
40
PGI-4-CSS-S-SC40
80
PGI-4-CSS-S-SC80
80
PGI-8-CSS-S-SC80
160
PGI-8-CSS-S-SC160
80
PGI-8-CSS-SS-SC80
160
PGI-8-CSS-SS-SC160
1/4 in. NPT

Steel
Stainless
steel
1/2 in. NPT
Ordering Number
Strap wrenches are used to remove the bayonet ring of the S,

B, and L model gauges.
Strap wrench ordering number: PGI-SB-CRR
P Model Accessories for Field Installation

Additional items for P model gauges can be ordered for field
installation.
Safety glass,
160 mm (6 in.) size
Cover ring remover,
115 mm (4 1/2 in.) size
Liquid-fill kit lower mount
(includes membrane and plug)
Inlet connection is 1/2 in. male NPT.

Available with 1/2 in. NPT and ISO parallel gauge
connections.
All 316 stainless steel construction.
Optional gauge siphon/snubber helps protect the
instrument from steam and vapor and dampens pressure

fluctuations.
Strap Wrenches
Kit
Safety glass,
115 mm (4 1/2 in.) size
pressure gauges.
Ordering Number
PGI-P-115-SGLASS
Material Grade/
ASTM Specification
Component
Connector
316, 316L/A479
Gauge nut, coupling
316, 316L/A479
Seal washer
Annealed 316 SS
Siphon tube, damper tube, plug
316 SS
Select a gauge adapter ordering number.
Pressure Rating
PGI-P-160-SGLASS
PGI-P-115-CRR
PGI-P-FILLKIT-LM
Liquid-fill kit lower-back mount

(includes membrane and plug)
PGI-P-FILLKIT-LBM
Mark pointer
PGI-P-115-MARK-A
Outlet
Connection
6000 psig (413 bar)
10 000 psig (689 bar)
1/2 in. female NPT
ASN44N6
ASN44N10
1/2 in. male NPT
ASN4N46
ASN4N410
G1/2 female ISO

(RG)
ASN44P6
ASN44P10
Gauge Adapter Ordering Numbers
To order an optional gauge siphon/snubber, add -SN to the

gauge adapter ordering number.
Example: ASN44N6-SN
21
22

Snubber FittingsGauge Protectors
Swagelok snubber fittings protect gauges and instruments
from system pressure surges and shocks. Pressure damping
(snubbing) is accomplished through the use of a porous
sintered 316 stainless steel element.
Installing a Swagelok snubber fitting upstream from the
gauge reduces the gauges response rate. The response
rate generally varies with the initial pressure drop across
the porous element of the snubber fitting and allows the
gauge to reach line pressure smoothly.
Typical
Installation
Snubber fittings should be used only to protect against

pressure shocks, impulses, and surges. Systems requiring
control of contaminants should use filters suited to the
application. See the Swagelok Filters catalog, MS-01-92.
Effective Element Area

Fittings with 1/8 in. Male NPT Ends
Elements
With five basic elements available, snubber fittings can meet
the requirements of fluid applications ranging from light gases
to liquids with viscosities above 1000 SUS (Saybolt universal
seconds) (220 cSt [mm2/s]). Element designators are stamped
on all fittings for proper identification.
0.019 in.2 (12.3 mm2)

All Other Fittings
0.062 in.2 (40.0 mm2)
Component
Sintered 316
stainless
steel element
(magnified 133)
Press-fit sleeve holds
element in place
Fluid
Light gases from
69 to 79 SUS
(13 to 16 cSt [mm2/s])
Air-steam from
75 to 119 SUS
(15 to 25 cSt [mm2/s])
Water, light oils from

75 to 250 SUS
(15 to 54 cSt [mm2/s])
Oils from
250 to 1000 SUS
(54 to 220 cSt [mm2/s])
Oils of
1000 SUS (220 cSt [mm2/s])
and above
Average Fluid
Flow Estimate
L/min
Material Grade/ASTM Specification
Fitting body
316 SS/A276 or brass/B453
Ferrules, nut
316 SS/A276 or brass/B453
Sleeve
316 SS/A276
Element
316 SS
Pressure Ratings Basis

Pressure ratings are based on ASME Code for Process Piping
B31.3, at 70F (20C).
Element
Designator
0.05
at 25 psig (1.72 bar)
2.4
3.3
1.3
0.9
Maximum Differential Pressure

Stainless Steel Fittings with 1/8 in. Male NPT Ends
5000 psig (344 bar)
All Other Fittings
Stated working pressures
Pressure must be applied only in the direction of the

flow arrow.
Temperature Ratings
Product is tested with air at ambient temperature. Flow estimate

is the average air flow multiplied by a ratio of nominal kinematic
viscosities (air/fluid).
Not available for ordering number -4-SRA-2.
Fitting
Material
Maximum Operating
Temperature
F (C)
Brass
400 (204)
316 SS
1000 (538)
23

Snubber FittingsGauge Protectors
Select a basic ordering number from the tables below.
Example: -4-SA-E
Add a body material designator.
Material
Designator
316 SS
SS
CA-PH-0214-DIM
SWAGELOK Snubber Fittings Adapter MS-01-96
Brass
Example: SS-4-SA-E
Add an element designator from the table on page 22.
Example: SS-4-SA-EG
Dimensions
Dimensions are for reference only, and are subject to change.
Dimensions shown with Swagelok tube fitting nuts finger-tight.
Adapter
F flat
Working Pressure
at 70F (20C)
psig (bar)
NPT Male/
Female
Pipe Size
in.
Basic
Ordering
Number
Brass
316 SS
1/4
-4-SA-E
1.40 (35.6)
3/4
2200 (151)
4400 (303)
1/2
-8-SA-E
1.94 (49.3)
1 1/16
2400 (165)
4900 (337)
Female
Pipe Size
in.
NPT
Male
Pipe Size
in.
Basic
Ordering
Number
Brass
316 SS
1/4
1/8
-4-SRA-2-E
1.26 (32.0)
3/4
3300 (227)
6600 (454)
1/4
-8-SRA-4-E
1.76 (44.7)
2200 (151)
4400 (303)
3/8
-8-SRA-6-E
1.83 (46.5)
2400 (165)
4900 (337)
Dimensions
in. (mm)
Reducing Adapter
NPT
CA-PH-0227-DIM
SWAGELOK Snubber Fittings Swagelok Tube Fitting MS-01-96
F flat
1/2
Working Pressure
at 70F (20C)
psig (bar)
Dimensions
in. (mm)
1 1/16
Maximum differential pressure: 5000 psig (344 bar).
Male NPT to
Swagelok Tube Fitting
F flat
NPT
Male
Pipe Size
in.
1/4
Tube
OD
in.
Basic
Ordering
Number
Working Pressure
at 70F (20C)
psig (bar)
Dimensions
in. (mm)
C
1/4
-4-SM-A-400 1.48 (37.6)
0.70 (17.8)
9/16
9/16
3/8
-4-SM-A-600 1.57 (39.9)
0.76 (19.3)
5/8
11/16
Brass
316 SS
2200 (151)
4400 (303)
For more information about pressure ratings of Swagelok tube fittings, see Swagelok Tubing Data, MS-01-107.
G flat
A
Additional Products
Pressure Regulators
Tube Fittings
Swagelok offers as full range of

pressure regulators:
Pressure-reducing models
Swagelok gaugeable tube fittings

and adapter fittings are available
in sizes from 1/16 to 2 in. and
2 to 50mm in a wide variety of
materials and configurations.
Back-pressure models
Gas cylinder changeover
model
Vaporizing models
For more information, see the
Swagelok Pressure Regulators
catalog, MS02230.

Swagelok Gaugeable Tube
Fittings and Adapter Fittings
catalog, MS01140.
Pressure Gauges For Panel Builders
Tubing Products
Swagelok panel builders

gauges monitor vacuum and
positive system pressures up
to 15000psi, 1000bar, or
100000 kPa and fit industrystandard 29/16in. (65.0mm)
panel hole cutout.
Swagelok offers a wide variety

of tubing products.
For more information, see the Swagelok Pressure Gauges for

Panel BuildersPBG Series catalog, MS02333.
Contact your authorized

Swagelok representative or
see these Swagelok catalogs
for more information:
Stainless Steel Seamless Tubing, Fractional, Metric, and
Imperial Sizes, MS01181

Ultrahigh-Purity and High-Purity Stainless Steel Tubing,
Fractional, Metric, and Imperial Sizes, MS-01-182.
Transducers
Swagelok industrial pressure
transducers electronically monitor
fluid system pressure in a variety
of analytical and process
applications.
Swagelok Industrial Pressure
Transducers catalog,
MS02225.
Safe Product Selection

When selecting a product, the total system design must
be considered to ensure safe, trouble-free performance.
Function, material compatibility, adequate ratings,
proper installation, operation, and maintenance are the
responsibilities of the system designer and user.
Caution: Do not mix or interchange parts with those of
other manufacturers.
Warranty Information
Swagelok products are backed by The Swagelok Limited
Lifetime Warranty. For a copy, visit swagelok.com or contact
your authorized Swagelok representative.
SwagelokTM Swagelok Company

20022014 Swagelok Company
Printed in U.S.A., AGS
February 2014, R13
MS-02-170

Pressure Gauge

Uploaded by

Copyright:

Available Formats

Pressure Gauge

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Pressure Gauge

Uploaded by

Copyright:

Available Formats

www.swagelok.

Pre ssure G auge s

Industrial and Process Pressure Gauges

Industrial Gauge Models

Swagelok Tube Adapters

B Model: General-Purpose Gauge

C Model: General-Purpose Gauge . . . . . . . . . . . . . . . . .

S Model: Solid-Front Safety Gauge . . . . . . . . . . . . . . . .

M Model: Miniature Gauge . . . . . . . . . . . . . . . . . . . . . . . 10

Testing and Calibration

Monitor vacuum and positive system pressures up to

Every Swagelok industrial pressure gauge is factory calibrated

15000psi, 1000 bar, or 100 MPa

Swagelok Tube Adapters Solve Alignment Problems

Swagelok Tube Adapters

Swagelok tube adapters are to be used ONLY in

Swagelok tube fittings. Use in fittings made by other

Industrial and Process Pressure Gauges

Swagelok Tube Adapter

10 000 psi, 600 bar,

3/8 in. and 10 mm

7500 psi, 500 bar,

1/2 in. and 12 mm

6000 psi, 400 bar,

6000 psi, 400 bar,

1/4 and 1/2 in.

15 000 psi, 1000 bar,

Male ISO Parallel Gauge Thread (EN)

6000 psi, 400 bar,

15 000 psi, 1000 bar,

Male ISO Parallel Gauge Thread (JIS)

15 000 psi, 1000 bar,

Male ISO Tapered Thread

6000 psi, 400 bar,

15 000 psi, 1000 bar,

Model Selection Guide

Configurations: LBM = lower-back mount

CBM = center-back mount

Glycerin- and silicone-filled gauges cannot be used

Industrial and Process Pressure Gauges

63 mm (2 1/2 in.) Dial Size

Vacuum to 0 psi through vacuum to

1/4 and 3/8 in.; 6 and 10 mm

Unfilled: 40 to 140F (40 to 60C)

Swagelok tube adapter

100 mm (4 in.) Dial Size

Glycerin-filled: 4 to 140F (20 to

29to 140F (34 to 60C)

0 to 0.1 MPa through 0 to 100 MPa

1/4 and 1/2 in. male NPT

63 mm (2 1/2 in.): 1.5 % of span

0.4 % for every 18F (10C)

(ASME B40.100 Grade B, EN 837-1

1.0% of span (ASME B40.100

160 mm (6 in.) Dial Size

63 mm (2 1/2 in.): center-back and

back and lower mount

Weather-tight (Nema 4X/IP65)

Glycerin, lowtemperature glycerin,

Wetted components listed in italics.

Swagelok Tube Adapters

Swagelok tube adapters are to be used ONLY in

Configurations: LBM = lower-back mount

Available for unfilled gauges only.

Not available with dial range maximums

S Model: Solid-Front Stainless

Not available with adjustable pointer; not

M Model: Stainless Steel Miniature Gauge