EM 1110-2-2002

30 Jun 95

Chapter 3
Causes of Distress and
Deterioration of Concrete

Table 3-1
Causes of Distress and Deterioration of Concrete
Accidental Loadings
Chemical Reactions
Acid attack

3-1. Introduction

Aggressive-water attack
Alkali-carbonate rock reaction

a. General. Once the evaluation phase has been

completed for a structure, the next step is to establish the
cause or causes for the damage that has been detected.
Since many of the symptoms may be caused by more than
one mechanism acting upon the concrete, it is necessary
to have an understanding of the basic underlying causes
of damage and deterioration. This chapter presents information on the common causes of problems in concrete.
These causes are shown in Table 3-1. Items shown in the
table are discussed in the subsequent sections of this
chapter with the following given for each: (1) brief discussion of the basic mechanism; (2) description of the
most typical symptoms, both those that would be observed
during a visual examination and those that would be seen
during a laboratory evaluation; and (3) recommendations
for preventing further damage to new or replacement
concrete. The last section of the chapter presents a logical method for relating the symptoms or observations to
the various causes.
b. Approach to evaluation. Deterioration of concrete
is an extremely complex subject. It would be simplistic
to suggest that it will be possible to identify a specific,
single cause of deterioration for every symptom detected
during an evaluation of a structure. In most cases, the
damage detected will be the result of more than one
mechanism. For example, corrosion of reinforcing steel
may open cracks that allow moisture greater access to the
interior of the concrete. This moisture could lead to
additional damage by freezing and thawing. In spite of
the complexity of several causes working simultaneously,
given a basic understanding of the various damagecausing mechanisms, it should be possible, in most cases,
to determine the primary cause or causes of the damage
seen on a particular structure and to make intelligent
choices concerning selection of repair materials and
methods.
3-2. Causes of Distress and Deterioration

Alkali-silica reaction
Miscellaneous chemical attack
Sulfate attack
Construction Errors
Corrosion of Embedded Metals
Design Errors
Inadequate structural design
Poor design details
Erosion
Abrasion
Cavitation
Freezing and Thawing
Settlement and Movement
Shrinkage
Plastic
Drying
Temperature Changes
Internally generated
Externally generated
Fire
Weathering

These loadings can generate stresses higher than the

strength of the concrete, resulting in localized or general
failure. Determination of whether accidental loading
caused damage to the concrete will require knowledge of
the events preceding discovery of the damage. Usually,
damage caused by accidental loading will be easy to
diagnose.
(2) Symptoms.
Visual examination will usually
show spalling or cracking of concrete which has been
subjected to accidental loadings. Laboratory analysis is
generally not necessary.

a. Accidental loadings.
(1) Mechanism. Accidental loadings may be characterized as short-duration, one-time events such as the
impact of a barge against a lock wall or an earthquake.

(3) Prevention. Accidental loadings by their very

nature cannot be prevented. Minimizing the effects of
some occurrences by following proper design procedures
(an example is the design for earthquakes) or by proper

3-1

EM 1110-2-2002
30 Jun 95
attention to detailing (wall armor in areas of likely
impact) will reduce the impacts of accidental loadings.
b. Chemical reactions. This category includes several specific causes of deterioration that exhibit a wide
variety of symptoms. In general, deleterious chemical
reactions may be classified as those that occur as the
result of external chemicals attacking the concrete (acid
attack, aggressive water attack, miscellaneous chemical
attack, and sulfate attack) or those that occur as a result
of internal chemical reactions between the constituents of
the concrete (alkali-silica and alkali-carbonate rock reactions). Each of these chemical reactions is described
below.

(2) Aggressive-water attack.

(a) Mechanism. Some waters have been reported to
have extremely low concentrations of dissolved minerals.
These soft or aggressive waters will leach calcium from
cement paste or aggregates. This phenomenon has been
infrequently reported in the United States. From the few
cases that have been reported, there are indications that
this attack takes place very slowly. For an aggressivewater attack to have a serious effect on hydraulic structures, the attack must occur in flowing water. This keeps
a constant supply of aggressive water in contact with the
concrete and washes away aggregate particles that become
loosened as a result of leaching of the paste (Holland,
Husbands, Buck, and Wong 1980).

(1) Acid attack.

(a) Mechanism. Portland-cement concrete is a highly
alkaline material and is not very resistant to attack by
acids. The deterioration of concrete by acids is primarily
the result of a reaction between the acid and the products
of the hydration of cement. Calcium silicate hydrate may
be attacked if highly concentrated acid exists in the environment of the concrete structures. In most cases, the
chemical reaction results in the formation of water-soluble
calcium compounds that are then leached away. In the
case of sulfuric acid attack, additional or accelerated
deterioration results because the calcium sulfate formed
may affect the concrete by the sulfate attack mechanism
(Section 3-2b(6)). If the acid is able to reach the reinforcing steel through cracks or pores in the concrete,
corrosion of the reinforcing steel will result and will cause
further deterioration of the concrete (ACI 201.2R).
(b) Symptoms. Visual examination will show disintegration of the concrete evidenced by loss of cement
paste and aggregate from the matrix (Figure 2-13). If
reinforcing steel has been reached by the acid, rust
staining, cracking, and spalling may be present. If the
nature of the solution in which the deteriorating concrete
is located is unknown, laboratory analysis can be used to
identify the specific acid involved.
(c) Prevention.
A dense concrete with a low
water-cement ratio (w/c) may provide an acceptable
degree of protection against a mild acid attack. Portlandcement concrete, because of its composition, is unable to
withstand attack by highly acidic solutions for long
periods of time. Under such conditions, an appropriate
surface coating or treatment may be necessary. ACI
Committee 515 has extensive recommendations for such
coatings (ACI 515.1R).

3-2

(b) Symptoms. Visual examination will show concrete surfaces that are very rough in areas where the paste
has been leached (Figure 2-12). Sand grains may be
present on the surface of the concrete, making it resemble
a coarse sandpaper. If the aggregate is susceptible to
leaching, holes where the coarse aggregate has been dissolved will be evident. Water samples from structures
where aggressive-water attack is suspected may be analyzed to calculate the Langlier Index, which is a measure
of the aggressiveness of the water (Langlier 1936).
(c) Prevention. The aggressive nature of water at
the site of a structure can be determined before construction or during a major rehabilitation. Additionally,
the water-quality evaluation at many structures can be
expanded to monitor the aggressiveness of water at the
structure. If there are indications that the water is aggressive or is becoming aggressive, areas susceptible to high
flows may be coated with a nonportland-cement-based
coating.
(3) Alkali-carbonate rock reaction.
(a) Mechanism. Certain carbonate rock aggregates
have been reactive in concrete. The results of these reactions have been characterized as ranging from beneficial
to destructive. The destructive category is apparently
limited to reactions with impure dolomitic aggregates and
are a result of either dedolomitization or rim-silicification
reactions. The mechanism of alkali-carbonate rock reaction is covered in detail in EM 1110-2-2000.
(b) Symptoms. Visual examination of those reactions that are serious enough to disrupt the concrete in a

EM 1110-2-2002
30 Jun 95
structure will generally show map or pattern cracking and
a general appearance which indicates that the concrete is
swelling (Figure 2-7). A distinguishing feature which
differentiates alkali-carbonate rock reaction from
alkali-silica reaction is the lack of silica gel exudations at
cracks (ACI 201.2R). Petrographic examination in accordance with ASTM C 295 (CRD-C 127) may be used to
confirm the presence of alkali-carbonate rock reaction.
(c) Prevention. In general, the best prevention is to
avoid using aggregates that are or suspected of being
reactive.
Appendix E of EM 1110-2-2000 prescribes
procedures for testing rocks for reactivity and for minimizing effects when reactive aggregates must be used.
(4) Alkali-silica reaction.
(a) Mechanism. Some aggregates containing silica
that is soluble in highly alkaline solutions may react to
form a solid nonexpansive calcium-alkali-silica complex
or an alkali-silica complex which can imbibe considerable
amounts of water and then expand, disrupting the
concrete.
Additional details may be found in
EM 1110-2-2000.
(b) Symptoms. Visual examination of those concrete
structures that are affected will generally show map or
pattern cracking and a general appearance that indicates
that the concrete is swelling (Figure 2-6). Petrographic
examination may be used to confirm the presence of
alkali-silica reaction.
(c) Prevention. In general, the best prevention is to
avoid using aggregates that are known or suspected to be
reactive or to use a cement containing less than
0.60 percent alkalies (percent Na20 + (0.658) percent
K20). Appendix D of EM 1110-2-2000 prescribes procedures for testing aggregates for reactivity and for minimizing the effects when reactive aggregates must be used.
(5) Miscellaneous chemical attack.
(a) Mechanism. Concrete will resist chemical attack
to varying degrees, depending upon the exact nature of
the chemical. ACI 515.1R includes an extensive listing of
the resistance of concrete to various chemicals. To produce significant attack on concrete, most chemicals must
be in solution that is above some minimum concentration.
Concrete is seldom attacked by solid dry chemicals.
Also, for maximum effect, the chemical solution needs to
be circulated in contact with the concrete. Concrete subjected to aggressive solutions under positive differential
pressure is particularly vulnerable. The pressure gradients

tend to force the aggressive solutions into the matrix. If

the low-pressure face of the concrete is exposed to evaporation, a concentration of salts tends to accumulate at that
face, resulting in increased attack. In addition to the
specific nature of the chemical involved, the degree to
which concrete resists attack depends upon the temperature of the aggressive solution, the w/c of the concrete,
the type of cement used (in some circumstances), the
degree of consolidation of the concrete, the permeability
of the concrete, the degree of wetting and drying of the
chemical on the concrete, and the extent of chemically
induced corrosion of the reinforcing steel (ACI 201.1R).
(b) Symptoms.
Visual examination of concrete
which has been subjected to chemical attack will usually
show surface disintegration and spalling and the opening
of joints and cracks. There may also be swelling and
general disruption of the concrete mass. Coarse aggregate
particles are generally more inert than the cement paste
matrix; therefore, aggregate particles may be seen as
protruding from the matrix. Laboratory analysis may be
required to identify the unknown chemicals which are
causing the damage.
(c) Prevention. Typically, dense concretes with low
w/c (maximum w/c = 0.40) provide the greatest resistance. The best known method of providing long-term
resistance is to provide a suitable coating as outlined in
ACI 515.1R.
(6) Sulfate attack.
(a) Mechanism.
Naturally occurring sulfates of
sodium, potassium, calcium, or magnesium are sometimes
found in soil or in solution in ground water adjacent to
concrete structures. The sulfate ions in solution will
attack the concrete. There are apparently two chemical
reactions involved in sulfate attack on concrete. First, the
sulfate reacts with free calcium hydroxide which is liberated during the hydration of the cement to form calcium
sulfate (gypsum). Next, the gypsum combines with
hydrated calcium aluminate to form calcium
sulfoaluminate (ettringite). Both of these reactions result
in an increase in volume. The second reaction is mainly
responsible for most of the disruption caused by volume
increase of the concrete (ACI 201.2R). In addition to the
two chemical reactions, there may also be a purely physical phenomenon in which the growth of crystals of sulfate
salts disrupts the concrete.
(b) Symptoms. Visual examination will show map
and pattern cracking as well as a general disintegration of

3-3

EM 1110-2-2002
30 Jun 95
the concrete (Figure 2-14). Laboratory analysis can verify
the occurrence of the reactions described.
(c) Prevention. Protection against sulfate attack can
generally be obtained by the following: Use of a dense,
high-quality concrete with a low water-cement ratio; Use
of either a Type V or a Type II cement, depending upon
the anticipated severity of the exposure (EM 1110-22000); Use of a suitable pozzolan (some pozzolans, added
as part of a blended cement or separately, have improved
resistance, while others have hastened deterioration). If
use of a pozzolan is anticipated, laboratory testing to
verify the degree of improvement to be expected is
recommended.
c. Construction errors. Failure to follow specified
procedures and good practice or outright carelessness may
lead to a number of conditions that may be grouped
together as construction errors. Typically, most of these
errors do not lead directly to failure or deterioration of
concrete. Instead, they enhance the adverse impacts of
other mechanisms identified in this chapter. Each error
will be briefly described below along with preventative
methods. In general, the best preventive measure is a
thorough knowledge of what these construction errors are
plus an aggressive inspection program. It should be noted
that errors of the type described in this section are equally
as likely to occur during repair or rehabilitation projects
as they are likely to occur during new construction.
(1) Adding water to concrete. Water is usually added
to concrete in one or both of the following circumstances:
First, water is added to the concrete in a delivery truck to
increase slump and decrease emplacement effort. This
practice will generally lead to concrete with lowered
strength and reduced durability. As the w/c of the concrete increases, the strength and durability will decrease.
In the second case, water is commonly added during
finishing of flatwork. This practice leads to scaling, crazing, and dusting of the concrete in service.
(2) Improper alignment of formwork.
Improper
alignment of the formwork will lead to discontinuities on
the surface of the concrete. While these discontinuities
are unsightly in all circumstances, their occurrence may
be more critical in areas that are subjected to highvelocity flow of water, where cavitation-erosion may be
induced, or in lock chambers where the rubbing surfaces must be straight.
(3) Improper consolidation. Improper consolidation
of concrete may result in a variety of defects, the most
common being bugholes, honeycombing, and cold joints.

3-4

Bugholes are formed when small pockets of air or water

are trapped against the forms. A change in the mixture to
make it less sticky or the use of small vibrators worked
near the form has been used to help eliminate bugholes.
Honeycombing can be reduced by inserting the vibrator
more frequently, inserting the vibrator as close as possible to the form face without touching the form, and
slower withdrawal of the vibrator. Obviously, any or all
of these defects make it much easier for any
damage-causing mechanism to initiate deterioration of the
concrete. Frequently, a fear of overconsolidation is
used to justify a lack of effort in consolidating concrete.
Overconsolidation is usually defined as a situation in
which the consolidation effort causes all of the coarse
aggregate to settle to the bottom while the paste rises to
the surface. If this situation occurs, it is reasonable to
conclude that there is a problem of a poorly proportioned
concrete rather than too much consolidation.
(4) Improper curing. Curing is probably the most
abused aspect of the concrete construction process.
Unless concrete is given adequate time to cure at a proper
humidity and temperature, it will not develop the characteristics that are expected and that are necessary to provide durability. Symptoms of improperly cured concrete
can include various types of cracking and surface disintegration. In extreme cases where poor curing leads to
failure to achieve anticipated concrete strengths, structural
cracking may occur.
(5) Improper location of reinforcing steel. This
section refers to reinforcing steel that is improperly
located or is not adequately secured in the proper location.
Either of these faults may lead to two general types of
problems. First, the steel may not function structurally as
intended, resulting in structural cracking or failure. A
particularly prevalent example is the placement of welded
wire mesh in floor slabs. In many cases, the mesh ends
up on the bottom of the slab which will subsequently
crack because the steel is not in the proper location. The
second type of problem stemming from improperly
located or tied reinforcing steel is one of durability. The
tendency seems to be for the steel to end up near the
surface of the concrete. As the concrete cover over the
steel is reduced, it is much easier for corrosion to begin.
(6) Movement of formwork. Movement of formwork during the period while the concrete is going from a
fluid to a rigid material may induce cracking and separation within the concrete. A crack open to the surface will
allow access of water to the interior of the concrete. An
internal void may give rise to freezing or corrosion problems if the void becomes saturated.

EM 1110-2-2002
30 Jun 95
(7) Premature removal of shores or reshores. If
shores or reshores are removed too soon, the concrete
affected may become overstressed and cracked.
In
extreme cases there may be major failures.
(8) Settling of the concrete.
During the period
between placing and initial setting of the concrete, the
heavier components of the concrete will settle under the
influence of gravity. This situation may be aggravated by
the use of highly fluid concretes. If any restraint tends to
prevent this settling, cracking or separations may result.
These cracks or separations may also develop problems of
corrosion or freezing if saturated.
(9) Settling of the subgrade. If there is any settling
of the subgrade during the period after the concrete begins
to become rigid but before it gains enough strength to
support its own weight, cracking may also occur.
(10) Vibration of freshly placed concrete. Most construction sites are subjected to vibration from various
sources, such as blasting, pile driving, and from the operation of construction equipment. Freshly placed concrete
is vulnerable to weakening of its properties if subjected to
forces which disrupt the concrete matrix during setting.
The vibration limits for concrete, expressed in terms of
peak particle velocity and given in Table 3-2, were established as a result of laboratory and field test programs.
(11) Improper finishing of flat work. The most common improper finishing procedures which are detrimental
to the durability of flat work are discussed below.
(a) Adding water to the surface. This procedure was
discussed in paragraph 3-2c(1) above. Evidence that
water is being added to the surface is the presence of a
large paint brush, along with other finishing tools. The
brush is dipped in water and water is slung onto the
surface being finished.

(b) Timing of finishing. Final finishing operations

must be done after the concrete has taken its initial set
and bleeding has stopped. The waiting period depends on
the amounts of water, cement, and admixtures in the
mixture but primarily on the temperature of the concrete
surface. On a partially shaded slab, the part in the sun
will usually be ready to finish before the part in the
shade.
(c) Adding cement to the surface. This practice is
often done to dry up bleed water to allow finishing to
proceed and will result in a thin cement-rich coating
which will craze or flake off easily.
(d) Use of tamper. A tamper or jitterbug is
unnecessarily used on many jobs. This tool forces the
coarse aggregate away from the surface and can make
finishing easier.
This practice, however, creates a
cement-rich mortar surface layer which can scale or craze.
A jitterbug should not be allowed with a well designed
mixture. If a harsh mixture must be finished, the judicious use of a jitterbug could be useful.
(e) Jointing. The most frequent cause of cracking in
flatwork is the incorrect spacing and location of joints.
Joint spacing is discussed in ACI 330R.
d.

Corrosion of embedded metals.

(1) Mechanisms. Steel reinforcement is deliberately

and almost invariably placed within a few inches of a
concrete surface. Under most circumstances, portlandcement concrete provides good protection to the embedded reinforcing steel.
This protection is generally
attributed to the high alkalinity of the concrete adjacent to
the steel and to the relatively high electrical resistance of
the concrete. Still, corrosion of the reinforcing steel is
among the most frequent causes of damage to concrete.

Table 3-2
Vibration Limits for Freshly Placed Concrete (Hulshizer and Desci 1984)
Age of Concrete
at Time of Vibration
(hr)

Peak Particle Velocity

of Ground Vibrations

Up to 3

102 mm/sec (4.0 in./sec)

3 to 11

38 mm/sec (1.5 in./sec)

11 to 24

51 mm/sec (2.0 in./sec)

24 to 48

102 mm/sec (4.0 in./sec)

Over 48

178 mm/sec (7.0 in./sec)

3-5

EM 1110-2-2002
30 Jun 95
(a) High alkalinity and electrical resistivity of the
concrete. The high alkalinity of the concrete pore solution can be reduced over a long period of time by carbonation. The electrical resistivity can be decreased by
the presence of chemicals in the concrete. The chemical
most commonly applied to concrete is chloride salts in the
form of deicers. As the chloride ions penetrate the concrete, the capability of the concrete to carry an electrical
current is increased significantly. If there are differences
within the concrete such as moisture content, chloride
content, oxygen content, or if dissimilar metals are in
contact, electrical potential differences will occur and a
corrosion cell may be established. The anodes will experience corrosion while the cathodes will be undamaged.
On an individual reinforcing bar there may be many
anodes and cathodes, some adjacent, and some widely
spaced.

becoming visible (Figure 2-27).

tory analysis may be beneficial is
chloride contents in the concrete.
used to determine the amount of
during a rehabilitation project.

(b) Corrosion-enhanced reduction in load-carrying

capacity of concrete. As the corrosion progresses, two
things occur: First, the cross-sectional area of the reinforcement is reduced, which in turn reduces the loadcarrying capacity of the steel. Second, the products of the
corrosion, iron oxide (rust), expand since they occupy
about eight times the volume of the original material.
This increase in volume leads to cracking and ultimately
spalling of the concrete. For mild steel reinforcing, the
damage to the concrete will become evident long before
the capacity of the steel is reduced enough to affect its
load-carrying capacity. However, for prestressing steel,
slight reductions in section can lead to catastrophic
failure.

e. Design errors. Design errors may be divided

into two general types: those resulting from inadequate
structural design and those resulting from lack of attention
to relatively minor design details. Each of the two types
of design errors is discussed below.

(c) Other mechanisms for corrosion of embedded

metals. In addition to the development of an electrolytic
cell, corrosion may be developed under several other
situations. The first of these is corrosion produced by the
presence of a stray electrical current. In this case, the
current necessary for the corrosion reaction is provided
from an outside source. A second additional source of
corrosion is that produced by chemicals that may be able
to act directly on the reinforcing steel. Since this section
has dealt only with the corrosion of steel embedded in
concrete, for information on the behavior of other metals
in concrete, see ACI 201.2R and ACI 222R.
(2) Symptoms. Visual examination will typically
reveal rust staining of the concrete. This staining will be
followed by cracking. Cracks produced by corrosion
generally run in straight, parallel lines at uniform intervals
corresponding to the spacing of the reinforcement. As
deterioration continues, spalling of the concrete over the
reinforcing steel will occur with the reinforcing bars

3-6

One area where laborathe determination of the

This procedure may be
concrete to be removed

(3) Prevention. ACI 201.2R describes the considerations for protecting reinforcing steel in concrete: use of
concrete with low permeability; use of properly proportioned concrete having a low w/c; use of as low a concrete slump as practical; use of good workmanship in
placing the concrete; curing the concrete properly; providing adequate concrete cover over the reinforcing steel;
providing good drainage to prevent water from standing
on the concrete; limiting chlorides in the concrete mixture; and paying careful attention to protruding items such
as bolts or other anchors.

(1) Inadequate structural design.

(a) Mechanism. The failure mechanism is simple-the concrete is exposed to greater stress than it is capable
of carrying or it sustains greater strain than its strain
capacity.
(b) Symptoms.
Visual examinations of failures
resulting from inadequate structural design will usually
show one of two symptoms. First, errors in design resulting in excessively high compressive stresses will result in
spalling. Similarly, high torsion or shear stresses may
also result in spalling or cracking. Second, high tensile
stresses will result in cracking. To identify inadequate
design as a cause of damage, the locations of the damage
should be compared to the types of stresses that should be
present in the concrete. For example, if spalls are present
on the underside of a simple-supported beam, high compressive stresses are not present and inadequate design
may be eliminated as a cause. However, if the type and
location of the damage and the probable stress are in
agreement, a detailed stress analysis will be required to
determine whether inadequate design is the cause. Laboratory analysis is generally not applicable in the case of
suspected inadequate design. However, for rehabilitation
projects, thorough petrographic analysis and strength testing of concrete from elements to be reused will be
necessary.

EM 1110-2-2002
30 Jun 95
(c) Prevention. Inadequate design is best prevented
by thorough and careful review of all design calculations.
Any rehabilitation method that makes use of existing
concrete structural members must be carefully reviewed.
(2) Poor design details. While a structure may be
adequately designed to meet loadings and other overall
requirements, poor detailing may result in localized concentrations of high stresses in otherwise satisfactory concrete. These high stresses may result in cracking that
allows water or chemicals access to the concrete. In other
cases, poor design detailing may simply allow water to
pond on a structure, resulting in saturated concrete. In
general, poor detailing does not lead directly to concrete
failure; rather, it contributes to the action of one of the
other causes of concrete deterioration described in this
chapter. Several specific types of poor detailing and their
possible effects on a structure are described in the following paragraphs. In general, all of these problems can
be prevented by a thorough and careful review of plans
and specifications for the project. In the case of existing
structures, problems resulting from poor detailing should
be handled by correcting the detailing and not by simply
responding to the symptoms.
(a) Abrupt changes in section. Abrupt changes in
section may cause stress concentrations that may result in
cracking. Typical examples would include the use of
relatively thin sections such as bridge decks rigidly tied
into massive abutments or patches and replacement concrete that are not uniform in plan dimensions.
(b) Insufficient reinforcement at reentrant corners and
openings. Reentrant corners and openings also tend to
cause stress concentrations that may cause cracking. In
this case, the best prevention is to provide additional
reinforcement in areas where stress concentrations are
expected to occur.
(c) Inadequate provision for deflection. Deflections
in excess of those anticipated may result in loading of
members or sections beyond the capacities for which they
were designed. Typically, these loadings will be induced
in walls or partitions, resulting in cracking.
(d) Inadequate provision for drainage. Poor attention
to the details of draining a structure may result in the
ponding of water. This ponding may result in leakage or
saturation of concrete. Leakage may result in damage to
the interior of the structure or in staining and encrustations on the structure. Saturation may result in severely
damaged concrete if the structure is in an area that is
subjected to freezing and thawing.

(e) Insufficient travel in expansion joints. Inadequately designed expansion joints may result in spalling
of concrete adjacent to the joints. The full range of possible temperature differentials that a concrete may be
expected to experience should be taken into account in the
specification for expansion joints. There is no single
expansion joint that will work for all cases of temperature
differential.
(f) Incompatibility of materials. The use of materials with different properties (modulus of elasticity or
coefficient of thermal expansion) adjacent to one another
may result in cracking or spalling as the structure is
loaded or as it is subjected to daily or annual temperature
variations.
(g) Neglect of creep effect. Neglect of creep may
have similar effects as noted earlier for inadequate provision for deflections (paragraph 3-2e(2)(c)). Additionally,
neglect of creep in prestressed concrete members may
lead to excessive prestress loss that in turn results in
cracking as loads are applied.
(h) Rigid joints between precast units. Designs
utilizing precast elements must provide for movement
between adjacent precast elements or between the precast
elements and the supporting frame. Failure to provide for
this movement can result in cracking or spalling.
(i) Unanticipated shear stresses in piers, columns, or
abutments. If, through lack of maintenance, expansion
bearing assembles are allowed to become frozen, horizontal loading may be transferred to the concrete elements
supporting the bearings. The result will be cracking in
the concrete, usually compounded by other problems
which will be caused by the entry of water into the
concrete.
(j) Inadequate joint spacing in slabs. This is one of
the most frequent causes of cracking of slabs-on-grade.
Guidance on joint spacing and depth of contraction joints
may be found in ACI 332R.
f. Abrasion. Abrasion damage caused by waterborne debris and the techniques used to repair the damage
on several Corps structures are described by McDonald
(1980). Also, causes of abrasion-erosion damage and
procedures for repair and prevention of damage are
described in ACI 210R.
(1) Mechanism. Abrasion-erosion damage is caused
by the action of debris rolling and grinding against a
concrete surface. In hydraulic structures, the areas most

3-7

EM 1110-2-2002
30 Jun 95
likely to be damaged are spillway aprons, stilling basin
slabs, and lock culverts and laterals. The sources of the
debris include construction trash left in a structure, riprap
brought back into a basin by eddy currents because of
poor hydraulic design or asymmetrical discharge, and
riprap or other debris thrown into a basin by the public.
Also barges and towboats impacting or scraping on lock
wells and guide wells can cause abrasions erosion
damage.
(2) Symptoms. Concrete surfaces abraded by waterborne debris are generally smooth (Figure 2-20) and may
contain localized depressions. Most of the debris remaining in the structure will be spherical and smooth.
Mechanical abrasion is usually characterized by long
shallow grooves in the concrete surface and spalling along
monolith joints. Armor plates is often torn away or bent.
(3) Prevention. The following measures should be
followed to prevent or minimize abrasion-erosion damage
to concrete hydraulic structures (Liu 1980 and McDonald
1980).
(a) Design. It appears that given appropriate flow
conditions in the presence of debris, all of the construction materials currently being used in hydraulic structures
are to some degree susceptible to erosion.
While
improvements in materials should reduce the rate of concrete damage caused by erosion, this improvement alone
will not solve the problem. Until the adverse hydraulic
conditions that can cause abrasion-erosion damage are
minimized or eliminated, it will be extremely difficult for
any of the construction materials currently being used to
avoid damage by erosion. Prior to construction or repair
of major structures, hydraulic model studies of the structure may be required to identify potential causes of erosion damage and to evaluate the effectiveness of various
modifications in eliminating those undesirable hydraulic
conditions.
Many older structures have spillways
designed with a vertical end-sill. This design is usually
efficient in trapping the erosion-causing debris within the
spillway. In some structures, a 45-deg fillet installed on
the upstream side of the end sill has resulted in a selfcleaning stilling basin. Recessing monolith joints in lock
walls and guide walls will minimize stilling basin spalling
caused by barge impact and abrasion (See
paragraph 8-1e(2)(e)).
(b) Operation. In existing structures, balanced flows
should be maintained into basins by using all gates to
avoid discharge conditions where eddy action is prevalent.
Substantial discharges that can provide a good hydraulic
jump without creating eddy action should be released
periodically in an attempt to flush debris from the stilling
3-8

basin. Guidance as to discharge and tailwater relations

required for flushing should be developed through model
and prototype tests.
Periodic inspections should be
required to determine the presence of debris in the stilling
basin and the extent of erosion. If the debris cannot be
removed by flushing operations, the basin should be
cleaned by other means.
(c) Materials. It is imperative that materials be
tested and evaluated, in accordance with ASTM C 1138
(CRD-C 63), prior to use in the repair of abrasion-erosion
damaged hydraulic structures. Abrasion-resistant concrete
should include the maximum amount of the hardest coarse
aggregate that is available and the lowest practical w/c.
In some cases where hard aggregate was not available,
high-range water-reducing admixtures (HRWRA) and
condensed silica fume have been used to develop high
compressive strength concrete 97 MPa (14,000 psi) to
overcome problems of unsatisfactory aggregate (Holland
1983). Apparently, at these high compressive strengths
the hardened cement paste assumes a greater role in
resisting abrasion-erosion damage, and as such, the
aggregate quality becomes correspondingly less important.
The abrasion-erosion resistance of vacuum-treated concrete, polymer concrete, polymer-impregnated concrete,
and polymer portland-cement concrete is significantly
superior to that of comparable conventional concrete that
can also be attributed to a stronger cement matrix. The
increased costs associated with materials, production, and
placing of these and any other special concretes in comparison with conventional concrete should be considered
during the evaluation process. While the addition of steel
fibers would be expected to increase the impact resistance
of concrete, fiber-reinforced concrete is consistently less
resistant to abrasion-erosion than conventional concrete.
Therefore, fiber-reinforced concrete should not be used
for repair of stilling basins or other hydraulic structures
where abrasion-erosion is of major concern. Several
types of surface coatings have exhibited good abrasionerosion resistance during laboratory tests. These include
polyurethanes, epoxy-resin mortar, furan-resin mortar,
acrylic mortar, and iron aggregate toppings. However,
some difficulties have been reported in field applications
of surface coatings, primarily the result of improper surface preparation and thermal incompatibility between
coatings and concrete.
g. Cavitation. Cavitation-erosion is the result of
relatively complex flow characteristics of water over
concrete surfaces (ACI 210R).
(1) Mechanism. There is little evidence to show that
water flowing over concrete surfaces at velocities less

EM 1110-2-2002
30 Jun 95
than 12.2 m/sec (40 ft/sec) causes any cavitation damage
to the concrete. However, when the flow is fast enough
(greater than 12.2 m/sec) and where there is surface irregularity in the concrete, cavitation damage may occur.
Whenever there is surface irregularity, the flowing water
will separate from the concrete surface. In the area of
separation from the concrete, vapor bubbles will develop
because of the lowered vapor pressure in the region. As
these bubbles are carried downstream, they will soon
reach areas of normal pressure. These bubbles will collapse with an almost instantaneous reduction in volume.
This collapse, or implosion, creates a shock wave which,
upon reaching a concrete surface, induces very high
stresses over a small area. The repeated collapse of vapor
bubbles on or near the concrete surface will cause pitting.
Concrete spillways and outlet works of many high dams
have been severely damaged by cavitation.
(2) Symptoms. Concrete that has been damaged will
be severely pitted and extremely rough (Figure 2-21). As
the damage progresses, the roughness of the damaged area
may induce additional cavitation.
(3) Prevention.
(a) Hydraulic design. Even the strongest materials
cannot withstand the forces of cavitation indefinitely.
Therefore, proper hydraulic design and the use of aeration
to reduce or eliminate the parameters that trigger cavitation are extremely important (ACI 210R). Since these
topics are beyond the scope of this manual, hydraulic
engineers and appropriate hydraulic design manuals
should be consulted.
(b) Conventional materials. While proper material
selection can increase the cavitation resistance of concrete,
the only totally effective solution is to reduce or eliminate
the causes of cavitation. However, it is recognized that in
the case of existing structures in need of repair, the reduction or elimination of cavitation may be difficult and
costly. The next best solution is to replace the damaged
concrete with more cavitation-resistant materials. Cavitation resistance of concrete can be increased by use of a
properly designed low w/c, high-strength concrete. The
use of no larger than 38-mm (1-1/2-in.) nominal maximum size aggregate is beneficial. Furthermore, methods
which have reduced the unit water content of the mixture,
such as use of a water-reducing admixture, are also beneficial. Vital to increased cavitation resistance are the use
of hard, dense aggregate particles and a good aggregateto-mortar bond. Typically, cement-based materials exhibit
significantly lower resistance to cavitation compared to
polymer-based materials.

(c) Other cavitation-resistant materials. Cavitationdamaged areas have been successfully repaired with steelfiber concrete and polymer concrete (Houghton, Borge,
and Paxton 1978). Some coatings, such as neoprene and
polyurethane, have reduced cavitation damage to concrete,
but since near-perfect adhesion to the concrete is critical,
the use of the coatings is not common. Once a tear or a
chip in the coating occurs, the entire coating is likely to
be peeled off.
(d) Construction practices. Construction practices
are of paramount importance when concrete surfaces are
exposed to high-velocity flow, particularly if aeration
devices are not incorporated in the design. Such surfaces
must be as smooth as can be obtained under practical
conditions. Accordingly, good construction practices as
given in EM 1110-2-2000 should be followed whether the
construction is new or is a repair. Formed and unformed
surfaces should be carefully checked during each construction operation to confirm that they are within specified tolerances. More restrictive tolerances on surfaces
should be avoided since they become highly expensive to
construct and often impractical to achieve, despite the use
of modern equipment and good construction practices.
Where possible, transverse joints in concrete conduits or
chutes should be minimized. These joints are generally in
a location where the greatest problem exists in maintaining a continuously smooth hydraulic surface. One construction technique which has proven satisfactory in
placement of reasonably smooth hydraulic surfaces is the
traveling slipform screed. This technique can be applied
to tunnel inverts and to spillway chute slabs. Hurd (1989)
provides information on the slipform screed. Since surface hardness improves cavitation resistance, proper curing of these surfaces is essential.
h.

Freezing and thawing.

(1) Mechanism. As the temperature of a critically

saturated concrete is lowered during cold weather, the
freezable water held in the capillary pores of the cement
paste and aggregates expands upon freezing. If subsequent thawing is followed by refreezing, the concrete is
further expanded, so that repeated cycles of freezing and
thawing have a cumulative effect. By their very nature,
concrete hydraulic structures are particularly vulnerable to
freezing and thawing simply because there is ample
opportunity for portions of these structures to become
critically saturated. Concrete is especially vulnerable in
areas of fluctuating water levels or under spraying conditions. Exposure in such areas as the tops of walls, piers,
parapets, and slabs enhances the vulnerability of concrete
to the harmful effects of repeated cycles of freezing and

3-9

EM 1110-2-2002
30 Jun 95
thawing. The use of deicing chemicals on concrete surfaces may also accelerate damage caused by freezing and
thawing and may lead to pitting and scaling. ACI 201.2R
describes the action as physical. It involves the development of osmotic and hydraulic pressures during freezing,
principally in the paste, similar to ordinary frost action.
(2) Symptoms. Visual examination of concrete damaged by freezing and thawing may reveal symptoms ranging from surface scaling to extensive disintegration
(Figure 2-10). Laboratory examination of cores taken
from structures that show surficial effects of freezing and
thawing will often show a series of cracks parallel to the
surface of the structure.
(3) Prevention. The following preventive measures
are recommended by ACI 201.2R for concrete that will be
exposed to freezing and thawing while saturated:
(a) Designing the structure to minimize the exposure
to moisture. For example, providing positive drainage
rather than flat surfaces whenever possible.
(b) Using a concrete with a low w/c.
(c) Using adequate entrained air to provide a satisfactory air-void system in the concrete, i.e., a bubble spacing
factor of 0.20 mm (0.008 in.) or less, which will provide
protection for the anticipated service conditions and
aggregate size. EM 1110-2-2000 provides information on
the recommended amount of entrained air.
(d) Selecting suitable materials, particularly aggregates that perform well in properly proportioned concrete.
(e) Providing adequate curing to ensure that the compressive strength of the concrete is at least 24 MPa
(3,500 psi) before the concrete is allowed to freeze in a
saturated state.
i.

(b) Subsidence. Situations in which an entire structure is moving or a single element of a structure, such as
a monolith, is moving with respect to the remainder of the
structure are caused by subsidence. In these cases, the
concerns are not overcracking or spalling but rather stability against overturning or sliding. Whether portions of a
single structural element are moving with respect to one
another or whether entire elements are moving, the underlying cause is more than likely to be a failure of the foundation material.
This failure may be attributed to
long-term consolidations, new loading conditions, or to a
wide variety of other mechanisms. In situations in which
structural movement is diagnosed as a cause of concrete
deterioration, a thorough geotechnical investigation should
be conducted.
(2) Symptoms. Visual examination of structures
undergoing settlement or movement will usually reveal
cracking or spalling or faulty alignment of structural
members. Very often, movement will be apparent in
nonstructural members such as block or brick masonry
walls. Another good indication of structural movement is
an increase in the amount of water leaking into the structure. Since differential settlement of the foundation of a
structure is usually a long-term phenomenon, review of
instrumentation data will be helpful in determining
whether apparent movement is real. Review by structural
and geotechnical engineering specialists will be required.
(3) Prevention. Prevention of settlements and movements or corrective measures are beyond the scope of this
manual. Appropriate structural and geotechnical engineering manuals should be consulted for guidance.
j. Shrinkage. Shrinkage is caused by the loss of
moisture from concrete. It may be divided into two general categories: that which occurs before setting (plastic
shrinkage) and that which occurs after setting (drying
shrinkage). Each of these types of shrinkage is discussed
in this section.

Settlement and movement.

(1) Plastic shrinkage.

(1) Mechanisms.
(a) Differential movement. Situations in which the
various elements of a structure are moving with respect to
one another are caused by differential movements. Since
concrete structures are typically very rigid, they can tolerate very little differential movement. As the differential
movement increases, concrete members can be expected
to be subjected to an overstressed condition. Ultimately,
the members will crack or spall.

3-10

(a) Mechanism. During the period between placing

and setting, most concrete will exhibit bleeding to some
degree. Bleeding is the appearance of moisture on the
surface of the concrete; it is caused by the settling of the
heavier components of the mixture. Usually, the bleed
water evaporates slowly from the concrete surface. If
environmental conditions are such that evaporation is
occurring faster than water is being supplied to the surface by bleeding, high tensile stresses can develop. These

EM 1110-2-2002
30 Jun 95
stresses can lead to the development of cracks on the
concrete surface.
(b) Symptoms. Cracking caused by plastic shrinkage
will be seen within a few hours of concrete placement.
Typically, the cracks are isolated rather than patterned.
These cracks are generally wide and shallow.
(c) Prevention. Determination of whether the weather
conditions on the day of the placement are conducive to
plastic shrinkage cracking is necessary. If the predicted
evaporation rate is high according to ACI 305R, appropriate actions such as erecting windbreaks, erecting shade
over the placement, cooling the concrete, and misting
should be taken after placement. Additionally, it will be
beneficial to minimize the loss of moisture from the concrete surface between placing and finishing. Finally,
curing should be started as soon as is practical. If cracking caused by plastic shrinkage does occur and if it is
detected early enough, revibration and refinishing of the
cracked area will resolve the immediate problem of the
cracks. Other measures as described above will be
required to prevent additional occurrences.
(2) Drying shrinkage.
(a) Mechanism. Drying shrinkage is the long-term
change in volume of concrete caused by the loss of moisture. If this shrinkage could take place without any
restraint, there would be no damage to the concrete.
However, the concrete in a structure is always subject to
some degree of restraint by either the foundation, by
another part of the structure, or by the difference in
shrinkage between the concrete at the surface and that in
the interior of a member. This restraint may also be
attributed to purely physical conditions such as the placement of a footing on a rough foundation or to chemical
bonding of new concrete to earlier placements or to both.
The combination of shrinkage and restraints cause tensile
stresses that can ultimately lead to cracking.
(b) Symptoms. Visual examination will typically
show cracks that are characterized by their fineness and
absence of any indication of movement. They are usually
shallow, a few inches in depth. The crack pattern is typically orthogonal or blocky. This type of surface cracking
should not be confused with thermally induced deep
cracking which occurs when dimensional change is
restrained in newly placed concrete by rigid foundations
or by old lifts of concrete.
(c) Prevention. In general, the approach is either to
reduce the tendency of the concrete, to shrink or to reduce

the restraint, or both. The following will help to reduce

the tendency to shrink: use of less water in the concrete;
use of larger aggregate to minimize paste content; placing
the concrete at as low a temperature as practical; dampening the subgrade and the forms; dampening aggregates
if they are dry and absorptive; and providing an adequate
amount of reinforcement to distribute and reduce the size
of cracks that do occur. Restraint can be reduced by
providing adequate contraction joints.
k. Temperature changes. Changes in temperature
cause a corresponding change in the volume of concrete.
As was true for moisture-induced volume change (drying
shrinkage), temperature-induced volume changes must be
combined with restraint before damage can occur. Basically, there are three temperature change phenomena that
may cause damage to concrete. First, there are the temperature changes that are generated internally by the heat
of hydration of cement in large placements. Second, there
are the temperature changes generated by variations in
climatic conditions. Finally, there is a special case of
externally generated temperature change--fire damage.
Internally and externally generated temperature changes
are discussed in subsequent paragraphs. Because of the
infrequent nature of its occurrence in civil works structures, fire damage is not included in this manual.
(1) Internally generated temperature differences.
(a) Mechanism. The hydration of portland cement is
an exothermic chemical reaction. In large volume placements, significant amounts of heat may be generated and
the temperature of the concrete may be raised by more
than 38 C (100 F) over the concrete temperature at
placement. Usually, this temperature rise is not uniform
throughout the mass of the concrete, and steep temperature gradients may develop. These temperature gradients
give rise to a situation known as internal restraint--the
outer portions of the concrete may be losing heat while
the inner portions are gaining (heat). If the differential is
great, cracking may occur. Simultaneously with the
development of this internal restraint condition, as the
concrete mass begins to cool, a reduction in volume takes
place. If the reduction in volume is prevented by external
conditions (such as by chemical bonding, by mechanical
interlock, or by piles or dowels extending into the concrete), the concrete is externally restrained. If the strains
induced by the external restraint are great enough, cracking may occur. There is increasing evidence, particularly
for rehabilitation work, that relatively minor temperature
differences in thin, highly restrained overlays can lead to
cracking. Such cracking has been seen repeatedly in lock
wall resurfacing (Figure 2-5) and in stilling basin

3-11

EM 1110-2-2002
30 Jun 95
overlays. Measured temperature differentials have typically been much below those normally associated with
thermally induced cracking.
(b) Symptoms.
Cracking resulting from internal
restraint will be relatively shallow and isolated. Cracking
resulting from external restraint will usually extend
through the full section. Thermally induced cracking may
be expected to be regularly spaced and perpendicular to
the larger dimensions of the concrete.
(c) Prevention. An in-depth discussion of temperature and cracking predictions for massive placements can
be found in ACI 207.1R and ACI 207.2R. In general, the
following may be beneficial: using as low a cement content as possible; using a low-heat cement or combination
of cement and pozzolans; placing the concrete at the
minimum practical temperature; selecting aggregates with
low moduli of elasticity and low coefficients of thermal
expansion; cooling internally or insulating the placement
as appropriate to minimizing temperature differentials; and
minimizing the effects of stress concentrators that may
instigate cracking.
(2) Externally generated temperature differences.
(a) Mechanism. The basic failure mechanism in this
case is the same as that for internally generated temperature differences--the tensile strength of the concrete is
exceeded. In this case the temperature change leading to
the concrete volume change is caused by external factors,
usually changing climatic conditions. This cause of deterioration is best described by the following examples:
First, a pavement slab cast in the summer. As the air and
ground temperatures drop in the fall and winter, the slab
may undergo a temperature drop of 27 C (80 F), or
more. Typical parameters for such a temperature drop
(coefficient of thermal expansion of 10.8 10-6/C (6
10-6/F) indicate a 30-m (98-ft) slab would experience a
shortening of more than 13 mm (1/2 in.). If the slab were
restrained, such movement would certainly lead to cracking. Second, a foundation or retaining wall that is cast in
the summer. In this case, as the weather cools, the concrete may cool at different rates--exposed concrete will
cool faster than that insulated by soil or other backfill.
The restraint provided by this differential cooling may
lead to cracking if adequate contraction joints have not
been provided. Third, concrete that experiences significant expansion during the warmer portions of the year.
Spalling may occur if there are no adequate expansion
joints. In severe cases, pavement slabs may be lifted out
of alignment, resulting in so-called blowups. Fourth,
concretes that have been repaired or overlayed with

3-12

materials that do not have the same coefficient of thermal

expansion as the underlying material. Annual heating and
cooling may lead to cracking or debonding of the two
materials.
(b) Symptoms. Visual examination will show regularly spaced cracking in the case of restrained contraction.
Similarly, spalling at expansion joints will be seen in the
case of restrained expansion. Problems resulting from
expansion-contraction caused by thermal differences will
be seen as pattern cracking, individual cracking, or
spalling.
(c) Prevention. The best prevention is obviously to
make provision for the use of contraction and expansion
joints. Providing reinforcing steel (temperature steel) will
help to distribute cracks and minimize the size of those
that do occur. Careful review of the properties of all
repair materials will help to eliminate problems caused by
temperature changes.
l. Weathering. Weathering is frequently referred to
as a cause of concrete deterioration. ACI 116R defines
weathering as Changes in color, texture, strength, chemical composition, or other properties of a natural or
artificial material due to the action of the weather. However, since all of these effects may be more correctly
attributed to other causes of concrete deterioration
described in this chapter, weathering itself is not considered to be a specific cause of deterioration.
3-3. Relating Symptoms to Causes
of Distress and Deterioration
Given a detailed report of the condition of the concrete in
a structure and a basic understanding of the various mechanisms that can cause concrete deterioration, the problem
becomes one of relating the observations or symptoms to
the underlying causes. When many of the different
causes of deterioration produce the same symptoms, the
task of relating symptoms to causes is more difficult than
it first appears. One procedure to consider is based upon
that described by Johnson (1965). This procedure is
obviously idealized and makes no attempt to deal with
more than one cause that may be active at any one time.
Although there will usually be a combination of causes
responsible for the damage detected on a structure, this
procedure should provide a starting point for an analysis.
a. Evaluate structure design to determine adequacy.
First consider what types of stress could have caused the
observed symptoms. For example, tension will cause
cracking, while compression will cause spalling. Torsion

EM 1110-2-2002
30 Jun 95
or shear will usually result in both cracking and spalling.
If the basic symptom is disintegration, then overstress
may be eliminated as a cause. Second, attempt to relate
the probable types of stress causing the damage noted to
the locations of the damage. For example, if cracking
resulting from excessive tensile stress is suspected, it
would not be consistent to find that type of damage in an
area that is under compression. Next, if the damage
seems appropriate for the location, attempt to relate the
specific orientation of the damage to the stress pattern.
Tension cracks should be roughly perpendicular to the
line of externally induced stress. Shear usually causes
failure by diagonal tension, in which the cracks will run
diagonally in the concrete section. Visualizing the basic
stress patterns in the structure will aid in this phase of the
evaluation. If no inconsistency is encountered during this
evaluation, then overstress may be the cause of the
observed damage. A thorough stress analysis is warranted
to confirm this finding. If an inconsistency has been
detected, such as cracking in a compression zone, the next
step in the procedure should be followed.
b. Relate the symptoms to potential causes. For this
step, Table 3-3 will be of benefit. Depending upon the
symptom, it may be possible to eliminate several possible
causes. For example, if the symptom is disintegration or
erosion, several potential causes may be eliminated by this
procedure.
c. Eliminate the readily identifiable causes. From
the list of possible causes remaining after symptoms have
been related to potential causes, it may be possible to
eliminate two causes very quickly since they are relatively
easy to identify. The first of these is corrosion of
embedded metals. It will be easy to verify whether the
cracking and spalling noted are a result of corrosion. The
second cause that is readily identified is accidental loading, since personnel at the structure should be able to
relate the observed symptoms to a specific incident.
d. Analyze the available clues. If no solution has
been reached at this stage, all of the evidences generated
by field and laboratory investigations should be carefully
reviewed. Attention should be paid to the following
points:
(1) If the basic symptom is that of disintegration of
the concrete surface, then essentially three possible causes
remain: chemical attack, erosion, and freezing and thawing. Attempts should be made to relate the nature and
type of the damage to the location in the structure and to
the environment of the concrete in determining which of

the three possibilities is the most likely to be the cause of

the damage.
(2) If there is evidence of swelling of the concrete,
then there are two possibilities: chemical reactions and
temperature changes. Destructive chemical reactions such
as alkali-silica or alkali-carbonate attack that cause swelling will have been identified during the laboratory investigation. Temperature-induced swelling should be ruled
out unless there is additional evidence such as spalling at
joints.
(3) If the evidence is spalling and corrosion and
accidental loadings have been eliminated earlier, the major
causes of spalling remaining are construction errors, poor
detailing, freezing and thawing, and externally generated
temperature changes. Examination of the structure should
have provided evidence as to the location and general
nature of the spalling that will allow identification of the
exact cause.
(4) If the evidence is cracking, then construction
errors, shrinkage, temperature changes, settlement and
movement, chemical reactions, and poor design details
remain as possible causes of distress and deterioration of
concrete. Each of these possibilities will have to be
reviewed in light of the available laboratory and field
observations to establish which is responsible.
(5) If the evidence is seepage and it has not been
related to a detrimental internal chemical reaction by this
time, then it is probably the result of design errors or
construction errors, such as improper location or installation of a waterstop.
e. Determine why the deterioration has occurred.
Once the basic cause or causes of the damage have been
established, there remains one final requirement: to
understand how the causal agent acted upon the concrete.
For example, if the symptoms were cracking and spalling
and the cause was corrosion of the reinforcing steel, what
facilitated the corrosion? Was there chloride in the concrete? Was there inadequate cover over the reinforcing
steel? Another example to consider is concrete damage
caused by freezing and thawing. Did the damage occur
because the concrete did not contain an adequate air-void
system, or did the damage occur because the concrete
used was not expected to be saturated but, for whatever
reason, was saturated? Only when the cause and its mode
of action are completely understood should the next step
of selecting a repair material be attempted.

3-13

EM 1110-2-2002
30 Jun 95

3-14