Maxus Manual

08-121-BFA_Maxus OM.
indd 1
Maxus
Autoloading shotgun
owners manual
6/22/09 2:59:55 PM
Important operating instructions for:
C o n t e n t s
Browning maxus
autoloading shotguns
You are Responsible for Firearms Safety.................................................2

General Description and Operation........................................................9
Nomenclature............................................................................................9
Serial Number.........................................................................................10
Initial Cleaning........................................................................................10
Operation of the Safety.......................................................................11
Assembly..................................................................................................12
Disassembly.............................................................................................14
Ammunition............................................................................................15
Magazine Capacity..................................................................................16
Three-Shot Adaptor (Plug)....................................................................17
Loading....................................................................................................20
Firing.......................................................................................................23
Unloading................................................................................................24
Magazine Cut-Off...................................................................................25
Interchangeable Choke Tube System.....................................................26
Adjusting Length of Pull........................................................................30
Adjusting Cast and Drop at Comb........................................................32
Extra Barrels............................................................................................35
Cleaning and Maintenance Suggestions................................................35
Removal of the Trigger Group...............................................................39
Removal of the Bolt Assembly...............................................................41
Lubricating the Action Tube and Spring...............................................44
Maintenance of Oil Finish Stocks..........................................................46
Models with Special Finishes.................................................................47
Service or Repair.....................................................................................48
If you have any questions about your new firearm, this

owners manual or other Browning products, contact:
Browning Customer Service
One Browning Place
Morgan, UT 84050-9326
Phone: (800) 333-3288
browning.com
Please use the space below to record information about
your new firearm.
Model ___________________________________________________
Serial Number_____________________________________________
Purchased From_ __________________________________________
Date of Purchase___________________________________________
THAN K Y OU F OR c h o O s ING a
Browning Maxus Shotgun.
The Maxus shotgun represents the most advanced gas-operated
technology available in autoloading shotguns. Maxus shotguns
combine the best of traditional Browning craftsmanship with
state-of-the-art design and manufacturing. Every detail of the
Maxus Hunter shotgun is engineered to provide you the best in
reliable operation and handling.
With a reasonable amount of care, your Maxus shotgun is designed
to give you many years of dependable, enjoyable service.
08-121-BFA_Maxus OM.indd 2-1
Page
6/22/09 2:59:56 PM
You Are Responsible For Firearms Safety
Failure to follow any of the following warnings could result

in serious injury or death.
Remember, safe gun handling does not stop with your firearms
mechanical safety devices, it starts there. Always treat this firearm
with the respect due a loaded, ready-to-fire firearm.
Some firearms do not have a mechanical safety. Many target

firearms, lever-action firearms and pistols do not have manual
safety mechanisms. Therefore it is critical to read and
understand the owners manual for every firearm which explains
the safe operation of the firearm.
There is no excuse for careless or abusive handling of any firearm.

At all times handle this firearm and all other firearms with intense
respect for their power and potential danger.
While it is a good idea to test your firearms mechanical safety

periodically for proper function, never test the safety while your
firearm is loaded or pointed in an unsafe direction.
Please read and understand all of the cautions, warnings, notices,

proper handling procedures and instructions outlined in this owners
manual before using your new firearm.
3 Whenever you handle any firearm, or hand it to someone,

always open the action immediately and visually check the
firearms chamber to Make certain that the firearm is
completely unloaded.
Make certain the firearm does not inadvertently contain any
ammunition. Always keep the chamber empty and the safety
in the on safe position unless shooting is imminent.
As a gun owner, you accept a set of demanding responsibilities. How

seriously you take these responsibilities can be the difference between
life and death.
1 ALWAYS KEEP THE MUZZLE OF YOUR firearm POINTED IN A SAFE

DIRECTION even though you are certain it is unloaded.
Never point any firearm at anything you do not intend to shoot.
Be extremely alert and aware of all persons and property within
the range of your ammunition.
2 Never rely totally on your Firearms mechanical safety
device. Like any mechanical device, a Safety can sometimes
fail; it can be jarred or inadvertently manipulated into an
unsafe condition.
The word safety describes a firearms trigger block mechanism,
sear block mechanism, hammer block mechanism or firing pin
block mechanism. Mechanical safeties are designed to place your
firearm in a safer status, and no guarantee can be made that the
firearm will not fire even if the safety is in the on safe position.
Mechanical safeties merely aid safe gun handling and are no
excuse for pointing your firearms muzzle in an unsafe direction.
See Operation of the Safety on page 11 for instructions on the
operation of this firearms safety.
2
4 Always WEAR Ear AND Eye PROTECTION WHEN SHOOTING.

Unprotected, repeated exposure to gunfire can cause hearing
damage. Wear hearing protection (shooting ear plugs or muffs)
to guard against such damage.
Wear shooting glasses to protect your eyes from flying particles.

Allow proper distance (eye relief) between a scope and your
eye when firing a scoped rifle, shotgun or pistol. Do not use
unorthodox shooting methods that could cause the rearward travel
of the slide or bolt of a firearm to contact your eyes, face or hands.
Always keep a safe distance between the muzzle of your firearm
and any persons nearby, as muzzle blast, debris and ejecting shells
could inflict serious injury.
Always wear eye protection when disassembling and cleaning any

firearm to prevent the possibility of springs, spring-tensioned
parts, solvents or other agents from contacting your eyes.
3
6/22/09 2:59:56 PM
5 Keep all firearms unloaded during transport, even

when stored in a holster, gun case, scabbard or
other container.
6 DROPPING or jarring A LOADED FIREARM CAN CAUSE
ACCIDENTAL DISCHARGE.
This can occur even with the safety in the on safe position. Be
extremely careful while hunting or during any shooting activity
to avoid dropping any firearm.
7 hunting from elevated surfaces such as treestands
is dangerous.
Doing so may increase the risk of mishandling a firearm. The
following rules should always be observed by you and those you
hunt with. Always make certain that the stand being used is safe
and stable. Always make certain that your firearm is unloaded
when it is being taken up and down from the stand. Always make
certain that your firearm is not dropped from the stand, or
dropped while it is being taken up or down from the stand.
Remember, a loaded firearm may discharge when dropped, even
with the safety in the on safe position.
8 Store your firearm and ammunition separately, well beyond
the reach of children.
Take prudent safeguards to ensure your firearm does not become
available to untrained, inexperienced or unwelcome hands. Store
all firearms in secure, locked cases or a gun safe. Keep your firearm
unloaded when not in use.
9 BEWARE OF BARREL OBSTRUCTIONS.
Mud, snow and an infinite variety of other objects may
inadvertently lodge in a barrel bore. It only takes a small
obstruction to cause dangerously increased pressures that
can damage your firearm and cause serious injury to yourself
and others.
BEFORE CHECKING FOR A BARREL OBSTRUCTION, BE CERTAIN

YOUR FIREARM IS COMPLETELY UNLOADED, THERE IS Not a
LIVE shell IN THE CHAMBER AND THE SAFETY IS IN THE
ON SAFE POSITION.
After assuring yourself that the firearm is completely unloaded,

open the breech or action and look through the barrel to be sure it
is clear of obstructions. If an obstruction is seen, no matter how
small it may be, clean the bore with a cleaning rod and patch as
described on page 36 of this owners manual.
10 Be alert to the signs of ammunition malfunction. if you

detect an off sound or light recoil when a shell is fired,
do not load another shell into the chamber.
If your firearm fails to fire, keep the muzzle pointed in a safe
direction for a minimum of 30 seconds. Carefully open the action
and remove the shell from the chamber. If the primer is indented,
the defective shell should be disposed of in a way that cannot
cause harm. If the primer is not indented, your firearm should
be examined by a qualified gunsmith and the cause of the
malfunction corrected before further use. Glance down the barrel
to make sure that no obstructions remain in the barrel. Completely
clear the barrel before loading and firing again. Failure to follow
these instructions can cause extensive damage to your firearm and
possible serious injury to yourself and others.
11 never insert a shell of the incorrect gauge into
any firearm.
The gauge of your firearm is marked on the barrel. Store all shells
of different gauges in completely separate and well-marked
containers. Never store shells of mixed gauges in a common
container or in your pockets. See page 15 for more information
on the correct ammunition for your firearm.
6/22/09 2:59:56 PM
12 examine every shell you put in your firearm.

We assume no responsibility for the use of unsafe or improper
firearm and ammunition combinations or damage or injury
caused by damaged ammunition. It is your responsibility
to read and heed all warnings in this owners manual and on
ammunition boxes. See page 15 for more information on the
correct ammunition for your firearm.
13 USE ONLY SAAMI APPROVED AMMUNITION.
The barrel and action of this firearm have been made with
substantial safety margins beyond the pressures developed by
established American commercial loads. Nevertheless, we can
assume no liability for incidents which occur through the use of
shells of nonstandard dimensions or which develop pressures
in excess of commercially available ammunition which has been
loaded in accordance with standards established by the Sporting
Arms and Ammunition Manufacturers Institute (SAAMI).
14 Make sure of adequate ventilation in the area that you
discharge a firearm. Lead exposure can occur from
discharging firearms in poorly ventilated areas, cleaning
firearms or handling ammunition.
Lead is a substance that has been known to cause birth defects,
reproductive harm and other serious injury. Wash hands
thoroughly after exposure to ammunition or after cleaning
a firearm.
15 do not snap the firing pin on an empty chamber; the
chamber may not be empty!
Treat every firearm with the respect due a loaded firearm, even
though you are certain the firearm is unloaded.
16 KEEP YOUR Fingers AWAY FROM THE TRIGGER WHILE LOADING
and unloading UNTIL shooting is imminent.
17 BE SURE OF YOUR TARGET AND BACKSTOP, particularly

during low light periods.
Know the range of your ammunition. Never shoot at water or
hard objects.
18 ALWAYS UNLOAD your firearms CHAMBER BEFORE CROSSING
A FENCE, CLIMBING A TREE, JUMPING A DITCH OR NEGOTIATING
OTHER OBSTACLES.
Never place your firearm on or against a fence, tree, car or other
similar object.
19 BE DEFENSIVE AND ON GUARD AGAINST UNSAFE GUN
HANDLING AROUND YOU AND OTHERS.
Dont be timid when it comes to firearms safety. If you observe
other shooters violating any of these safety precautions, politely
suggest safer handling practices.
20 BE CERTAIN your firearm is UNLOADED BEFORE CLEANING.
Because so many firearm accidents occur when a firearm is being
cleaned, special and extreme care should be taken to be sure your
firearm is unloaded before disassembly, cleaning and reassembly.
Keep ammunition away from the cleaning location. Never test the
mechanical function of any firearm with live ammunition.
21 TEACH AND SUPERVISE FIREARMS SAFETY TO ALL MEMBERS OF
YOUR FAMILY, ESPECIALLY TO CHILDREN AND NON-SHOOTERS.
Closely supervise newcomers to the shooting sports. Encourage
enrollment in hunting and shooting safety courses.
22 NEVER DRINK ALCOHOLIC BEVERAGES OR TAKE ANY TYPE
OF DRUGS BEFORE OR DURING SHOOTING.
Your vision, motor skills and judgment could be dangerously
impaired, making your gun handling unsafe to you and to others.
6/22/09 2:59:56 PM
23 read AND HEED ALL WARNINGS in this owners manual, on

ammunition boxes and with all accessories that you install
on your firearm.
It is your responsibility to secure the most up-to-date information
on the safe handling procedures of your Browning firearm. We
assume no liability for incidents which occur when unsafe or
improper firearm accessories or ammunition combinations
are used.
24 Practice periodic MAINTENANCE, AVOID UNAUTHORIZED SERVICING.
Your firearm is a mechanical device which will not last forever,
and as such, is subject to wear and requires periodic inspection,
adjustment and service. Browning firearms should be serviced by
a Browning Recommended Service Facility or by our Service
Facility in Arnold, Missouri. We assume no responsibility for
injuries suffered or caused by unauthorized servicing, alterations
or modifications of Browning firearms.
25 WE RESERVE THE RIGHT TO REFUSE SERVICE ON FIREARMS THAT
HAVE BEEN ALTERED, ADDED TO OR SUBSTANTIALLY CHANGED.
Removal of metal from the barrel, or modifications of the firing
mechanism and/or operating parts, may lead to a refusal of service
on such firearms. We will charge you for parts and labor to return
the firearm to original specifications.
DO NOT, UNDER ANY CIRCUMSTANCES, ALTER THE TRIGGER, SAFETY

OR other PARTS OF THE FIRING MECHANISM OF THIS OR ANY
OTHER FIREARM. FAILURE TO OBEY THIS WARNING MAY RESULT IN
INJURY OR DEATH TO YOURSELF OR OTHERS.
Be careful!
Figure 1
Bolt Handle
Buttstock
Receiver
Safety
Recoil Pad
Trigger
Rib
Barrel
Front Sight Bead
Muzzle
Forearm
Speed Lock Lever

Bolt Release Button
G e n e r a l d e s c r i p t i o n a n d Op e r a t i o n
The Browning Maxus is a gas-operated, autoloading shotgun capable
of quickly firing up to five shells (with the three-shot adaptor
removed, using 2" loads), one shell at a time, with each successive
pull of the trigger. Upon firing, high-pressure gases from behind the
shot charge pass through two ports in the barrel, through the gas
bracket and into the gas system, forcing it rearward. As the gas system
moves rearward, it forces the bolt to the rear, operating the action.
As the bolt moves rearward, it cocks the hammer and ejects the fired
shell. After full rearward travel, the bolt returns forward, picks up a
new shell from the magazine and chambers it. After the last shell
has been fired, the bolt locks to the rear facilitating fast reloading.
N o m e n c l at u r e
In conventional firearm terminology the position and movement of
firearm parts are described as they occur with the firearm horizontal
and in the normal firing position: i.e., the muzzle is forward or in
front; the buttstock is rearward or to the rear; the trigger is downward
or underneath; the rib is upward or on top. For general parts
nomenclature, refer to Figure 1. For specific parts names related to
disassembly, refer to Figure 2.
6/22/09 2:59:56 PM
C LEANING
Figure 2
Barrel
Gas Bracket
Bolt
Barrel Extension
Piston Sleeve Spring
Slide Link
Bolt Slide
Recoil Pad
Bolt Handle
Piston Sleeve
Gas Piston
Magazine
Receiver
Three-Shot Adaptor
Forearm
Trigger Group
Trigger Group Pins
Serial Number
The serial number of your Maxus shotgun is found on the left side of
the receiver, above the trigger guard. Record this number in the space
provided at the front of this owner's manual for future reference.
Figure 3
Various exposed metal parts of

your new firearm have been
coated at the factory with a rust
preventative compound. Before
assembling your shotgun, clean
the anti-rust compound from the
inside of the barrel, receiver and
the action/chamber areas. A highquality lightweight gun oil is ideal
Lightly lubricate the bolt rails inside
the receiver.
for removing this compound, and
for giving your new firearm its first
lubrication. Place a drop of lightweight gun oil on both sides of the
inside of the receiver on the rails on which the bolt slides (Figure 3).
Clean the barrel using a cleaning rod and patch as explained under
Cleaning and Maintenance Suggestions on page 35.
o p e r at i o n o f t h e S a f e t y
Initial Cleaning
NOTICE! PLEASE TAKE NOTE OF THE FOLLOWING INFORMATION BEFORE
CLEANING YOUR FIREARM.
C l e a n i n g P a r t s w i t h Sp e c i a l F i n i s h e s
Be especially careful when cleaning firearms with camouflage,

Dura-Touch Armor Coating and other special finishes. Always
prevent these surfaces from coming in contact with cleaning solvents,
barrel scrubbers and other strong chemicals. It is preferable to clean
these surfaces with a lightweight gun oil containing no solvents, or
with a damp cloth and mild dish soap (be sure to keep water out of
the action). When cleaning your firearms bore and action, protect the
external finishes from any contact with chemicals used. Also, avoid
any contact between external finishes and other strong chemicals like
those found in DEET-containing insect repellents, sunscreens, etc.
Damage to camouflage, Dura-Touch and other finishes caused by
chemicals is irreversible and not repairable.
10
Always keep the safety in the on safe position unless

shooting is imminent. Always keep the muzzle pointed in a
safe direction. Failure to follow these warnings could
result in serious injury or death.
Figure 4
Figure 5
The safety shown in the on safe position.
The safety shown in the off safe position.
11
6/22/09 2:59:56 PM
The safety is designed to prevent the trigger from being pulled when
in the on safe position. The safety is located at the rear of the trigger
guard (Figure 4, page 11). In the off safe position, a red warning band
is visible on the safety button on the left side of the trigger guard.
Figure 6
Figure 7
Press and hold the release button while lifting

the Speed Lock lever.
Align the push rod with the slot in the receiver.
To place the firearm on safe, press the safety button to the right.
To move the safety to the off safe or fire position, press the safety
button to the left. This exposes the red warning band on the safety
button (Figure 5, page 11).
Do not depend on the red color alone to indicate your
firearms safety status. time, exposure to the elements, and
the abrasive action of cleaning agents can erase it. Failure to
follow this warning could result in serious injury or death.
The safety can be reversed from right- to left-handed by a

qualified gunsmith. When installed, the left-handed safety will
have the safety buttons red warning band on the right side of
the trigger guard.
ASSEM B L Y
ALWAYS KEEP the muzzle pointed in a safe direction. BEFORE
STARTING ASSEMBLY PROCEDURES, VISUALLY INSPECT THE CHAMBER
TO BE ABSOLUTELY CERTAIN THE FIREARM IS COMPLETELY UNLOADED.
place the safety in the on safe position. Failure to follow
this warning could result in serious injury or death.
The Maxus shotgun is delivered in the box with the barrel removed
and the forearm attached to the magazine tube. The Maxus features
the innovative Speed Lock forearm that makes removing the forearm
for cleaning or taking down the shotgun fast and easy.
1 Lock the bolt rearward by pulling the operating handle fully
to the rear.
12
Notice! NEVER ALLOW THE ACTION TO SLAM CLOSED BY PRESSING

THE bolt RELEASE BUTTON WITHOUT THE BARREL INSTALLED.
If the bolt is released forward with the barrel removed, the
operating handle will strike the receiver and cause damage.
2 Remove the forearm from the magazine tube by pressing and

holding the release button while lifting the Speed Lock lever
(Figure 6). Slide the forearm forward and off the magazine tube.
Notice! Do not squeeze hard on the open rear end of a wood
forearm. Too much pressure could cause the wood to split.
3 The gas system remains in place and does not need to be removed
except for cleaning. If the gas system has been removed, reinstall it
as explained below. Otherwise, proceed to step 5.
4 Slide the gas system (push rod end first) onto the magazine tube.
Align the push rod with the slot in the left side of the receiver.
(Figure 7). Make sure the gas system spring is properly positioned.
5 Align the barrel extension with the top of the receiver and place
the gas bracket over the magazine tube (Figure 8, page 14). The
barrel extension should slip solidly into the receiver. Make sure
the push rod moves freely in its slot in the receiver.
13
6/22/09 2:59:57 PM
Figure 8
Figure 9
1 Lock the bolt rearward by pulling the operating handle fully to

the rear.
Notice! NEVER ALLOW THE ACTION TO SLAM CLOSED BY PRESSING THE
bolt RELEASE BUTTON WITHOUT THE BARREL INSTALLED. If the bolt is
released forward with the barrel removed, the operating
handle will strike the receiver and cause damage.
2 Remove the forearm as explained previously.
Slide the barrel and piston over the magazine

tube and the barrel extension into the receiver.
Ensure the forearm is secured correctly, with

the button flush with the forearm, as shown in
the picture on the left.
6 Replace the forearm by sliding it onto the magazine tube and over
the gas bracket so it seats securely. Make sure the Speed Lock lever
is fully closed. It may be necessary to push rearward on the forearm
slightly to ensure the forearm is locked in place. When the forearm
is in place and the Speed Lock lever is fully locked, the release
button is flush with the surface of the forearm (Figure 9).
ALWAYS ensure the forearm is fully locked and the Speed lock
lever release button is flush with the surface of the forearm.
Failure to follow this warning could result in serious injury,
death or damage to your firearm.
Notice! Do not squeeze hard on the open rear end of a wood

forearm. Too much pressure could cause the wood to split.
3 For cleaning, remove the barrel and gas system by sliding

them forward and off the magazine tube. See Cleaning and
Maintenance Suggestions on page 35 for cleaning procedures.

For storage, remove the barrel and reinstall the forearm over the
magazine tube. You will then have two compact units: the barrel,
and the action with stock and forearm.
Notice! AFTER THE BARREL HAS BEEN REMOVED, LEAVE THE BOLT
IN THE rearward POSITION. DO NOT PRESS THE bolt RELEASE
BUTTON. If the bolt is released forward with the barrel
removed, the operating handle will strike the receiver,
causing damage.
Ammunition
DISASSEM B L Y
STARTING DISASSEMBLY PROCEDURES, open the action and VISUALLY
INSPECT THE Chamber TO BE ABSOLUTELY CERTAIN THE FIREARM IS
COMPLETELY UNLOADED. place the safety in the on safe
position. Failure to follow this warning could result in
serious injury or death.
14
use only shells of the correct gauge and length. The gauge
and length of the chamber is inscribed on the side of the
barrel. Do not use ammunition other than what is inscribed
on the side of the barrel. Examine every shell you put in your
shotgun. failure to follow this warning could result in
serious injury or death and cause damage to your shotgun.
Use shells of the correct length. Do not use 3" or 3" shells
in a barrel with a 2" chamber, or 3" shells in a barrel with
15
6/22/09 2:59:57 PM
a 3" chamber. Doing so can result in a buildup of dangerously

high pressures. failure to follow this warning could result
in serious injury or death and cause damage to your shotgun.
do not put a 16 or 20 gauge shell in a 12 gauge shotgun. do
not put a 28 gauge shell in a 20 gauge shotgun. do not put a
.410 bore shell in a 28 gauge shotgun. never put metallic
cartridges of any kind in a shotgun. specifically, never put
centerfire rifle or pistol cartridges in a shotgun chambered
for .410 bore. failure to follow this warning could result in
serious injury or death and cause damage to your shotgun.
The most certain way to bulge or rupture a shotgun barrel is to load

a smaller gauge shell into a larger gauge chamber. The smaller gauge
shell will not fall completely through the barrel; its rim is caught by
the front of a larger gauge chamber or at the larger gauges choke.
Your shotgun will misfire (with the chamber appearing to be empty).
It is then possible to load the correct gauge shell behind the smaller
gauge shell. If the shotgun is then fired, the result will be a so-called
12-16, 12-20, 20-28 or 28-.410 burst which can cause extensive
damage to your shotgun and possible serious injury to you and others.
We can assume no responsibility for incidents which occur through
the use of shells of nonstandard dimension or those developing
pressures in excess of SAAMI (Sporting Arms and Ammunition
Manufacturers Institute) established standards.
Maxus 12 gauge, 3" chamber models will shoot all 12 gauge, 2" and
3", 1 oz. and heavier factory lead and steel field loads. Maxus 12 gauge,
3" chamber models will shoot all 1 oz. and heavier factory lead and
steel 12 gauge, 2", 3" and 3" field loads.
Magazine capacity
With the magazine three-shot adapter (plug) removed, Maxus 3"
shotguns will hold four 2" or three 3" shells in the magazine.
Maxus 3" shotguns will hold four 2" shells, or three 3" or 3"
shells in the magazine.
16
three-shot adapter (Plug)

removing or installing the three-shot adaptor, completely
unload the shotgun. open the action and VISUALLY INSPECT
THE CHAMBER, feed mechanism and magazine TO BE ABSOLUTELY
CERTAIN THE FIREARM IS COMPLETELY UNLOADED. place the safety
in the on safe position. Failure to follow this warning could
WEAR EYE PROTECTION WHEN removing or installing the
three-shot adaptor TO PREVENT springs, spring-loaded
parts, SOLVENTS OR OTHER AGENTS FROM CONTACTING YOUR
EYES, resulting in injury.
The Maxus is delivered with the magazine three-shot adapter (plug)

installed in the magazine, limiting magazine capacity to two shells in
compliance with federal migratory bird regulations. If you do not
wish to be limited to three shots, when it is not required by law, you
can remove (or reinstall) the three-shot adapter as follows:
Removing the three-shot adaptor (plug)
1 Lock the bolt rearward by pulling the operating handle fully

to the rear.
Bolt RELEASE BUTTON WITHOUT THE BARREL INSTALLED. If the bolt is
2 Remove the forearm as explained previously.

3 The Maxus features the unique TurnKey Magazine Plug which
is quickly and easily removed by inserting a key or standard
screwdriver into the slot in the end of the magazine tube. To
remove the three-shot magazine adaptor, press inward and turn
17
6/22/09 2:59:57 PM
Figure 10
Use a key or small screwdriver to press in

on the three-shot adaptor, then rotate a
quarter-turn.
Figure 11
Remove the three-shot adaptor.
the key or flat-blade screwdriver a quarter-turn to align the threeshot adaptor with the slot in the end of the magazine (Figure 10).
This unlocks the three-shot adaptor, allowing it to be removed.
4 If the barrel is on the shotgun, hold it to prevent it from falling out
of the receiver while pointing the magazine tube down to allow the
three-shot adaptor (plug) to fall out of the end of the magazine
tube. Grasp and remove it (Figure 11).
5 Reinstall the forearm as explained previously. When the forearm is
in place and the Speed Lock lever is fully locked, the release button
is flush with the surface of the forearm (Figure 8, page 14).
1 Lock the bolt rearward by

pulling the operating handle
fully to the rear.
Notice! NEVER ALLOW THE ACTION
TO SLAM CLOSED BY PRESSING THE
Bolt RELEASE BUTTON WITHOUT THE
BARREL INSTALLED. If the bolt is
released forward with
the barrel removed, the
operating handle will strike the
receiver and cause damage.
Figure 12
The three-shot adaptor shown secured in the

magazine tube.
2 Remove the forearm as

explained previously.
3 Insert the magazine three-shot adapter into the slot in the end of
the magazine tube.
4 Insert a key or flat-blade screwdriver into the slot in the end of the
magazine tube. Press inward and turn the key or screwdriver a
quarter-turn to secure the three-shot adaptor in the magazine
(Figure 12).
5 Reinstall the forearm as explained previously. When the forearm is
in place and the Speed Lock lever is fully locked, the release button
is flush with the surface of the forearm (Figure 8, page 14).
I n s ta l l i n g t h e t h r e e - s h o t a d a p t o r ( p l u g )
If you need to install the magazine three-shot adaptor (plug) to

limit your shotgun magazine to three shells, again perform the
following operation:
18
19
6/22/09 2:59:57 PM
Loading
When loading your shotgun Always keep the muzzle pointed
in a safe direction, Always place the sAFETY IN THE ON SAFE
position and keep your fingers away from the trigger.
Failure to follow these warnings could result in serious
injury or death.
Do not carry your shotgun with a shell in the chamber to
avoid accidental discharge. when firing is no longer imminent,
make sure the safety is in the on safe position and unload
the chamber. Failure to follow these warnings could result in
always take care when loading the magazine. The edges of the
carrier are sharp and may cause injury to fingers or damage
to gloves.
Sp e e d L o a d i n g
1 If shooting is imminent, lock the bolt open and insert a shell into
the magazine (Figure 13). The shell will be automatically cycled
from the magazine to the chamber.
the magazine, using your thumb to position it fully forward in the

magazine tube. Make sure the rim of the shell engages the shell
stop and is held fully inside the magazine tube. It will make an
audible click when fully inserted.
THE SHOTGUN IS now READY TO FIRE BY SIMPLY MOVING THE SAFETY
TO THE OFF SAFE POSITION and pulling the trigger.
loading the magazine
1 Pull the operating handle to the rear until the bolt locks in the
open position. Visually inspect the chamber, feed mechanism
and magazine to make sure they are unloaded and clear of
any obstructions.
2 Close the bolt by pressing the bolt release button.
3 Insert a shell of the proper gauge and length through the loading
port at the bottom of the receiver up into the magazine, using
your thumb to position it fully forward in the magazine tube
(Figure 13). Make certain the rim of the shell engages the shell
stop and is held fully inside the magazine tube. It will make an
audible click when fully inserted.
4 If desired, continue loading the magazine until it is full.
Keep your fingers clear of the

ejection port when loading
the shotgun using the Speed
Loading procedure. Failure to
follow this warning could
result in injury.
2 If desired, load the magazine to

full capacity by inserting a shell
of proper gauge and length
through the loading port at the
bottom of the receiver up into
20
Figure 13
L o a d i n g t h e c h a m b e r M a n u a l ly f r o m t h e M a g a z i n e
1 With the bolt closed, depress the carrier with the front of the shell
and, using your thumb, push the shell into the magazine until the
shell is held in place by the shell stop.
2 If desired, continue to load the magazine, as explained above, to
full capacity.
Insert the shell into the bottom of the receiver

and push it fully forward into the magazine.
3 If shooting is imminent, a shell can now be moved from the

magazine to the chamber by pulling back fully on the operating
handle and releasing it forward. A shell will be fed automatically
from the magazine to the chamber as the bolt closes. Another shell
can then be inserted into the magazine to load to full capacity.
21
6/22/09 2:59:57 PM
Figure 14
THE SHOTGUN IS now READY TO

FIRE BY SIMPLY MOVING THE
SAFETY TO THE OFF SAFE
POSITION and pulling the
trigger.
F IRING
never load a shell into the chamber or place the safety in
the off safe position unless shooting is imminent. Always keep
the muzzle pointed in a safe direction. Failure to follow these
warnings could result in serious injury or death.
Loading the chamber through

the ejection port
1 Place the safety in the on safe position.
1 Pull the operating handle to the

rear until the bolt locks in the
Insert a shell through the ejection port into
the breech.
open position. Visually inspect
the chamber, feed mechanism
and magazine to make sure they are clear of any obstructions.
2 Load a shell into the chamber as explained previously.
2 If shooting is imminent, insert a shell of the proper gauge and

length through the ejection port into the open breech (Figure 14).
3 Press the bolt release button to deliver the shell into
the chamber.
Keep your fingers clear of the ejection port whenever closing
the action with the bolt release button. Failure to follow this
warning could result in injury.
4 With a shell in the chamber, you may load the magazine to full
capacity. To load the magazine, insert a shell of proper gauge and
length through the loading port at the bottom of the receiver up
into the magazine, using your thumb to position it fully forward
in the magazine tube. Make sure the rim of the shell engages the
shell stop and is held fully inside the magazine tube. It will make
an audible click when fully inserted.
22
3 With a shell in the chamber, you need only move the safety to
the off safe position to fire the shotgun.
4 When ready to fire, move the safety into the off safe position,
take aim and squeeze the trigger.
After a shell is fired, the gas system operates the bolt, ejects the fired
shell and picks up a loaded shell from the magazine and automatically
chambers it. You may continue to fire the shotgun until the magazine
is empty by pulling the trigger to fire each shell. After the last shell is
fired, the breech of the shotgun remains open, with the bolt locked to
the rear. This allows convenient and fast reloading.
If you are done shooting, leave the bolt locked to the rear, with the
breech in the open position so that you may visually inspect the
chamber, bore, carrier and magazine to be sure they contain no shells.
After firing, or when shooting is no longer imminent,
immediately PLACE THE SAFETY IN THE ON SAFE POSITION.
Failure to follow these warnings could result in serious
injury or death.
EVEN WITH THE bolt LOCKED OPEN AFTER SHOOTING, DO NOT ASSUME
the SHOTGUN IS UNLOADED. ALWAYS INSPECT THE CHAMBER, barrel,
feed mechanism AND MAGAZINE TO BE certain THE shotgun is
completely unloaded. Failure to follow these warnings could
23
6/22/09 2:59:57 PM
Unloading
when unloading your shotgun Always place the safety in the
on safe position. keep the muzzle pointed in a safe direction
and your fingers away from the trigger. Failure to follow
these warnings could result in serious injury or death.
ALWAYS INSPECT THE CHAMBER, barrel, feed mechanism and
mAGaZINE CAREFULLY AFTER UNLOADING TO BE SURE ALL LIVE shells
ARE CLEARED FROM THE firearm.
Sp e e d U n l o a d i n g
1 With the safety in the on safe position, turn the shotgun over so
the trigger guard is facing up, then push the carrier down with
your finger as far as it will go.
2 Shells are retained in the magazine by the shell stop, which catches
the rim of the shell base. Locate the shell stop inside the receiver
on the right side of the loading port (visually to the left side when
looking down into the loading port).
3 Push inward on the shell stop with your index finger (Figure 15)
to release a shell from the magazine. As the shell stop is pressed in,
the shell will be forced out of the magazine under spring pressure.
Catch the shell in your hand
as it comes out.
Figure 15
4 Press the stop again to release the
next shell. Continue to do this
until the magazine is empty. Be
careful not to pinch your finger.
5 With the safety still in the on
safe position, pull rearward on
the bolt handle to eject the shell
from the chamber. The bolt will
lock rearward when the action is
cycled with an empty magazine.
24
6 Using your index finger, feel the opening of the magazine to make
sure there are no shells that have not been fed from the magazine
and ejected. Visually inspect the chamber, feed mechanism and
magazine to assure there are no shells remaining.
U n l o a d i n g by C yc l i n g t h e Ac t i o n
1 With the safety in the on safe position, grasp the bolt handle and
cycle the action until all shells are transferred from the magazine to
the chamber and then ejected. Take care to avoid damaging shells.
Avoid letting them fall to the ground.
2 When the last shell in the magazine has been cycled through the
chamber and out the ejection port, the bolt will lock rearward. The
bolt will lock rearward when cycled with an empty magazine.
3 Using your index finger, feel the opening of the magazine to make
sure there are no shells that have not been fed from the magazine
and ejected. Visually inspect the chamber, feed mechanism and
magazine to assure there are no shells remaining.
M a g a z i n e C u t - o ff
when unloading your shotgun Always place the safety in the
on safe position. keep the muzzle pointed in a safe direction
and your fingers away from the trigger. Failure to follow
these warnings could result in serious injury or death.
The Magazine Cut-Off allows you to unload a shell from the chamber
without cycling a shell from the magazine. With this feature you can
quickly and easily load a heavier or lighter shell into the chamber
should the need arise. To change loads in the chamber using the
Magazine Cut-Off, perform the following operation:
Push inward on the shell stop to unload

the magazine.
1 Pull the Magazine Cut-Off lever to the rear to engage the magazine
cut-off and block the magazine (Figure 16, page 26). With the lever
to the rear, shells are locked in the magazine. Additionally, shells
cannot be loaded into the magazine with the lever to the rear.
25
6/22/09 2:59:58 PM
Figure 16
Figure 17
Always place the "sAFETY" IN THE ON SAFE position and keep

your fingers away from the trigger. Failure to follow these
warnings could result in serious injury or death.
DO NOT FIRE THIS SHOTGUN WITHOUT the correct cHOKE TUBE
INSTALLed. Permanent damage May result to the threads inside
the barrel.
USE ONLY THE APPROPRIATE GAUGE AND TYPE OF CHOKE TUBES,
MARKED INVECTOR-PLUS or Standard INVECTOR, DEPENDING ON
YOUR SHOTGUN.
Pull the Magazine Cut-Off rearward to block

the magazine.
Push the Magazine Cut-Off forward to unblock

the magazine.
2 Pull the bolt handle fully rearward to eject the shell in the chamber.
3 Load a shell through the ejection port as explained on page 22.
4 The shotgun may now be fired as explained on page 23 and will

fire only the shell in the chamber.
5 To disengage the Magazine Cut-Off, place the "safety" in the on safe
position, then push the Magazine Cut-Off lever fully forward
(Figure 17). If the action is open, shells will immediately feed from
the magazine. If the action is closed, a shell can be loaded into the
chamber from the magazine.
I n t e r c h a n g e a b l e C h o k e t u b e Sy s t e m
NEVER ATTEMPT TO REMOVE OR INSTALL A choke tube iN A LOADED
FIREARM. whenever removing or installing a choke tube in a
shotgun, Always keep the muzzle pointed in a safe direction.
completely unload the shotgun. open the action and VISUALLY
INSPECT THE CHAMBER, feed mechanism and magazine TO BE
ABSOLUTELY CERTAIN THE FIREARM IS COMPLETELY UNLOADED.
26
Invector-Plus choke tubes are for use only in Browning

shotguns with back-bored barrels, and are not interchangeable
with Standard Invector choke tubes. Do not use Invector-Plus
tubes in barrels threaded for Standard Invector tubes.
Standard Invector tubes are for use only in Browning
shotguns, and are not interchangeable with Invector-Plus
choke tubes. Do not use Standard Invector tubes in barrels
threaded for Invector-Plus tubes.
DO NOT USE BROWNING Standard INVECTOR or invector-plus
CHOke TUBES IN ANY SHOTGUN BARRELS NOT SUPPLIED BY BROWNING.
DO NOT USE ANY OTHER CHOKING DEVICE IN ANY SHOTGUN BARRELS
SUPPLIED BY BROWNING.
Failure to follow these warnings may cause injury or death
and cause damage to your shotgun.
All Maxus shotgun barrels are threaded to accept the Invector-Plus

choke system. Standard Invector and Invector-Plus tubes are not
interchangeable. Confirm the choke system of your shotgun by
looking on the right side of the barrel where the specifications are
inscribed, where the choke markings are normally located.
The constriction of each choke tube is indicated twice on the choke
tube: on the side of the tube, and indicated with a notch code on the
top rim of the tube. The included universal choke tube wrench is used
to remove and install choke tubes.
27
6/22/09 2:59:58 PM
Invector choke tubes are compatible with factory ammunition that has
been loaded in compliance with SAAMI specifications, including
magnum lead and steel shot loads, sabots and shotgun slug loads.
Figure 18
One Notch
Three Notches
Five Notches
Two Notches
Four Notches
No Notches
Rim
Notches
Pat t e r n w i t h
Lead Shot
Pat t e r n w i t h
Steel Shot
Extended**
X-Full Turkey
**
Full
II
I m p. M o d i f i e d
Full1
III
Modified
Full1
Replacement and additional tubes and wrenches are available from

your Browning dealer, or by contacting the Browning Customer
Service Department at (800) 333-3288.
C h o k e TU B E SELE C TION
To help you choose the correct choke tube for each hunting
and shooting situation, all Browning Invector choke tubes are
inscribed on the side with the patterns they produce with both
lead and steel shot. Each Invector tube also has notches in the
top rim of the tube (Figure 18, page 29). These notches are a code
to allow you to determine the choke designation while the tube is
installed. Rim notches refer specifically to lead shot. You will need to
use the charts on page 29 to cross-reference from lead to steel, and
determine the appropriate tube for your ammunition and hunting/
shooting situation.
Several choke tubes are supplied with your shotgun. The choke tubes
listed are also available as accessories. Remember, Standard Invector
and Invector-Plus tubes are not interchangeable. Invector-Plus tubes
are for Browning shotguns with back-bored barrels only. Before
removing or installing tubes, or reading the rim notch code, make
sure your shotgun is completely unloaded.
C h o k e TU B E REMOVAL
1 Place the safety in the on safe position. Always make sure the
shotgun is completely unloaded. Always keep the muzzle pointed
in a safe direction.
2 Use the choke tube wrench to loosen the tube, turning it
counterclockwise (Figure 19, page 30). Finger-twist the tube
the rest of the way out of the barrel.
28
IIII
I m p. C y l i n d e r
Modified
IIIII
Skeet
I m p. C y l i n d e r
No Notches
Cylinder
Cylinder
Not for use with steel shot. Using an over-tight choke constriction with
steel shot will result in an ineffective blown pattern.
**
Extra Full Special, extended with ports. Do not use with steel shot.
When more than one choke designation is listed for a given steel shot
pattern, use the more open choke listed for high velocity, larger shot size
steel loads.
29
6/22/09 2:59:58 PM
C h o k e TU B E INSTALLATION
Figure 19
Figure 20
Figure 21
Use the choke tube wrench to change

choke tubes.
Insert a screwdriver into the holes in the

recoil pad.
Install or remove stock spacers to achieve

correct length of pull.
1 Place the safety in the on safe

position. Always make sure the
shotgun is completely unloaded.
Always keep the muzzle pointed
in a safe direction.
2 Before installing a tube, check
the internal choke tube threads
in the muzzle, as well as the
threads on the choke tube to be
sure they are clean. Lightly oil
the threads with a high-quality,
lightweight gun oil.
3 Using your fingers, screw the appropriate tube into the muzzle of
the barrel, tapered end first, notched end outward. When it is
finger-tight, use the choke tube wrench to firmly seat the tube.
NOTICE! The choke tube should be periodically checked to
assure that it is tight and firmly seated. Before checking,
follow all choke tube removal and installation safety
guidelines previously outlined.
Adjusting Length of PUll

The buttstock can be adjusted for length of pull by adding or
removing spacers (available separately) to the rear of the stock. Each
spacer extends length of pull " and a maximum of three spacers can
be added with the screws provided to extend length of pull ". With
longer screws (not provided), more than three spacers can be added to
further extend length of pull.
Spacers can be ordered through your Browning dealer or by calling
our Customer Service Department at (800) 322-4626.
30
Before performing adjustment procedures, place the safety

in the on safe position. open the action and make certain YOUR
shotgun IS completely UNLOADED. Keep the muzzle pointed in a
safe direction. Failure to follow these warnings could result
I n s ta l l i n g a s p a c e r
1 Use a #2 cross tip or Phillips screwdriver to remove the recoil pad

at the end of the buttstock (Figure 20). Place a small amount of
petroleum jelly on the screw access slits on the top and bottom of
the rear of the buttstock to prevent damaging the recoil pad. Insert
the screwdriver into each of the two access holes. Make certain the
tip of the screwdriver engages the head of the screw. Turn the
screw counterclockwise until the screw is completely loose from
the stock. When both screws are free, remove the recoil pad.
2 Add or subtract spacers to fit your firearm to your specifications
(Figure 21). After making an adjustment hold the shotgun to your
shoulder to determine if the new length feels comfortable.
Remember to always keep the muzzle pointed in a safe direction,
with the safety in the on safe position and make certain the
shotgun is completely unloaded.
31
6/22/09 2:59:58 PM
3 When you are satisfied with the

length of pull, start the screws
through the pad and spacer(s)
into the holes in the stock.
Figure 22
4 Attach the recoil pad to the stock

using the screwdriver. Turn the
screws clockwise to tighten. Do
not overtighten the screws.
Adjusting Cast and

D r o p at C o m b
Cast and drop adjustment shims. Shim 2 comes

on your shotgun and is not shown.
Before performing adjustment procedures, place the safety

in the on safe position. open the action and make certain YOUR
Six shims are included with your new shotgun (Figure 22). The
shims fit between the buttstock and receiver, allowing customized
adjustments to the comb and heel. Each shim is labeled/stamped for
a specific amount of adjustment. The neutral shim, No. 2, is already
installed on your shotgun.
Drop at comb is defined as the place on the comb that your cheek rests
when taking aim. If drop at comb is correct, your eye naturally falls in
line with the sight. Shims marked 1, 2 and 3 do not give any cast on or
off. The stock remains straight. They only adjust drop at comb.
These shims with their respective stamps are further clarified here:
Shim 1 raises the comb approximately 1/16", and the heel
approximately 1/8".
Shim 2 is neutral. This shim is already installed on the firearm.
Shim 3 lowers the comb approximately 1/16", and the heel
approximately 1/8".
32
Cast is the offset of the buttstock from the longitudinal center line of
the firearm. Some right-handed shooters like the stock to angle away
(cast off) from their face, making their line of sight more directly in
line with the barrel. Angling the stock to the left for left-handed
shooters is cast on. Shims marked 1R1L, 2R2L, and 3R3L, will all
adjust drop at comb the same amount as shims 1, 2 and 3, and will also
adjust the cast right or left approximately 1/8". You will notice that the
two opposing edges of these spacers are different in thickness. For
right-handed shooters, install shims between the receiver and the stock
with the R facing the end of the buttstock, so its thicker side is on the
left side. This casts the stock slightly to the right, away from the face of
a right-handed shooter. If you turn the shim around so the L is facing
the end of the buttstock, and it will cast the stock to the left. These
shims with their respective stamps are further clarified below:
Shim 1R1L raises the comb approximately 1/16", and the heel
approximately 1/8" and will adjust the cast on or cast off
approximately 1/8".
Shim 2R2L adds the same amount of cast to the stock as shim
1R1L with neutral drop like shim 2.
Shim 3R3L adds the same amount of cast to the stock as shims
1R1L and 2R2L, and lowers the comb approximately 1/16" and the
heel approximately 1/8".
I n s ta l l i n g a S h i m
1 Make sure your shotgun is completely unloaded and the safety is

in the on safe position.
2 Use a #2 cross tip or Phillips screwdriver to remove the recoil pad at
the end of the buttstock (Figure 20). Place a small amount of
petroleum jelly on the screw access slits on the top and bottom of
the rear of the buttstock to prevent damaging the recoil pad.
Insert the screwdriver into each of the two access holes. Make
certain the tip of the screwdriver engages the head of the screw.
Turn the screw counterclockwise until the screw is completely loose
from the stock. When both screws are free, remove the recoil pad.
33
6/22/09 2:59:58 PM
3 Remove the stock insert to

access the stock bolt nut
(Figure 23).
Figure 23
Before installing an accessory barrel on your shotgun, read

the following guidelines to ensure the barrel/shotgun
combination is safe. place the safety in the on safe position.
open the action and make certain YOUR shotgun IS completely
UNLOADED. Keep the muzzle pointed in a safe direction. Failure
to follow these warnings could result in serious injury
or death.
4 Use a " socket wrench to

remove the two stock bolt
nuts and stock bolt washer.
(Figure 24).
5 Completely remove the
buttstock from the receiver,
along with the existing shim,
and install the shim you have
selected (Figure 25). Make
certain you have the proper
shim installed and in position
before reattaching the buttstock
and recoil pad.
Remove the stock insert.
Figure 24
Never use a barrel with a 3" chamber on a shotgun designed for

barrels with a 3" chamber.
Never use any other barrel from any other manufacturer on your
shotgun. Some other brands may seem similar, but the barrels are
not interchangeable.
Use a socket wrench to remove the stock bolt.
Figure 25
8 Reinstall the stock insert.
C LEANING a n d m a i n t e n a n c e SUGGESTIONS
C l e a n i n g P a r t s w i t h Sp e c i a l F i n i s h e s
Install the shim between the stock and receiver.
Never use a barrel from any other Browning shotgun.

NOTICE! PLEASE TAKE NOTE OF THE FOLLOWING INFORMATION BEFORE
CLEANING YOUR FIREARM.
9 Reinstall the recoil pad with care,

so as not to scratch or mar the
finish of the stock.
34
The versatility of your new shotgun can be extended with an extra

barrel. Maxus shotgun barrels are interchangeable within a given
gauge and chamber length. No special fitting is required. However,
some important restrictions must be observed:
Never use a barrel with a 3" chamber on a shotgun designed for
barrels with a 3" chamber.
6 When you are satisfied with

the fit, reattach the buttstock
to the receiver with the washer
and the nuts.
7 Snug the nuts down with
the socket wrench, do not
overtighten.
Extra Barrels
Be especially careful when cleaning firearms with camouflage,

Dura-Touch Armor Coating and other special finishes. Always
prevent these surfaces from coming in contact with cleaning solvents,
barrel scrubbers and other strong chemicals. It is preferable to clean
these surfaces with a lightweight gun oil containing no solvents or
35
6/22/09 2:59:59 PM
with a damp cloth and mild dish soap (be sure to keep water out of
the action). When cleaning your firearms bore and action, protect the
external finishes from any contact with chemicals used. Also avoid any
contact between external finishes and other strong chemicals like
those found in DEET-containing insect repellents, sunscreens, etc.
Damage to camouflage, Dura-Touch and other finishes caused by
chemicals is irreversible and not repairable.
BEFORE PERFORMING CLEANING PROCEDURES, place the safety in
the on safe position. open the action and make certain YOUR
WEAR EYE PROTECTION WHEN DISASSEMBLING AND CLEANING YOUR
shotgun TO PREVENT springs, spring-loaded parts, SOLVENTS OR
OTHER AGENTS FROM CONTACTING YOUR EYES, resulting in injury.
cleaning requires removal of the barrel from the receiver (cleaning the
barrel) and the removal of the gas system components. A complete
cleaning requires removal of the bolt and trigger group.
If a malfunction occurs, perform a thorough cleaning to see if it solves
the problem before seeking the services of a Browning Recommended
Service Center, the Browning Service Facility in Arnold, Missouri, or a
qualified gunsmith.
1 Place the safety in the on safe position. Open the action and
inspect the chamber and magazine to make certain they do not
contain any shells. Keep the muzzle pointed in a safe direction.
2 Remove the forearm and barrel as explained under Disassembly
on page 14.
3 Using a shotgun cleaning rod with tip and patch large enough for
a snug fit in the bore, insert the rod and a lightly oiled patch in the
breech end of the barrel and run back and forth through the bore
several times. Remove and wipe the choke tube, threads and barrel
threads with a nylon brush and lightly oil.

Keep all ammunition away from the cleaning area. Never

test the mechanical function of your shotgun with live
ammunition. Failure to follow these warnings could result
C LEANING TH e b a r r e l
Your Maxus shotgun will function better and more reliably over a
longer period of time if it is properly maintained and kept clean.
You should clean your shotgun after every day of shooting, and more
often if it becomes excessively dirty. At a minimum the barrel should
be cleaned and the action wiped clean and oiled after every day of
shooting. The gas system should require only occasional cleaning.
Normal maintenance can be accomplished with the barrel still
attached to the receiver (oiling and wiping down). More careful
36
Alternately, the Browning Barrel Weasel makes cleaning the bore

of your firearm fast and easy. Be sure to follow all instructions
when using any product to clean your firearm.
4 Inspect the bore from both ends for leading and plastic residue
that often remain in the bores from the shot cups in modern
shells. Leading and plastic residue will appear as longitudinal
streaks and are usually more predominant near the muzzle and
just forward of the chamber. A normal amount of either is
common and not serious.
5 If leading or plastic residue seems excessive you can remove it by
brushing the bore with a brass brush. Soak the brush or spray the
bore with a powder solvent first. Scrub until clean. To prevent
bristles from breaking off, push the brush fully through the barrel
each time before pulling it back through.
37
6/22/09 2:59:59 PM
MOST SOLVENTS ARE HIGHLY FLAMMABLE. WEAR EYE PROTECTION and

practice APPROPRIATE SAFETY MEASURES WHEN WORKING WITH
SOLVENTS to avoid serious injury.
6 After all leading and plastic residues have been removed, run a
clean, dry patch through the bore. Follow this with a final, lightly
oiled patch.
7 Reassemble the shotgun and wipe all exposed metal surfaces with
an oiled cloth making sure to wipe away all finger marks where
moisture could accumulate.
be easier to remove the piston sleeve spring to clean the interior of

the piston sleeve. Spray the inside of the gas piston. A green
Scotch-Brite kitchen scrub pad works best for removal of heavy
carbon fouling on the tube and inside the gas piston. Do not
remove the spring inside of the piston. Never use a steel brush on
any of the gas components.
4 Complete the cleaning of the gas system by applying a very light
film of oil to all parts for protection and lubrication. Reassemble
the gas system by snapping the piston sleeve into the gas piston.
periodic oiling
8 Inspect the barrel and chamber to be certain no patches have

inadvertently been left in them. Remove any that remain.
The metal parts of a firearm should receive a light film of oil after
the firearm has been exposed to weather or handling.
9 Lightly oil your firearm at the points described under Periodic

Oiling on page 40. Regular, light oiling is extremely important to
the durability and reliable operation of your shotgun.
Occasionally, a drop of lightweight gun oil may be placed inside

the receiver on the rails on which the bolt slides (Figure 3, page 11),
and on the surface of the magazine tube, where the gas piston slides.
This reduces friction for smooth operation.
10 The wood surfaces can also be wiped with a quality, lightweight

gun oil or they can be polished with any quality furniture wax
(but not both).
C LEANING THE GAS S Y STEM
1 Remove the gas system from

the magazine tube as explained
in Disassembly on page 14.
Figure 26
38
NOTICE! Do not place large quantities of oil into the action.

excess oil will run back into the wood of the stock softening
the wood, with consequential loosening of the stock.
r e m o va l o f t h e T r i g g e r G r o u p
2 To simplify cleaning the gas

system, separate the gas piston
from the piston sleeve by
pulling them apart (Figure 26).
3 Spray the magazine tube, gas
piston and piston sleeve with
gun solvent and brush them
thoroughly with a nylon brush
to remove any deposits. It will
If the firearm has been exposed to excessive dust, dirt, mud or water,
the principal working parts including the gas system, should be wiped
clean and lubricated with a light film of quality, lightweight gun oil.
BEFORE removing the trigger group, place the safety in the

on safe position. open the action and make certain YOUR
Separate the gas system components to
simplify cleaning.
39
6/22/09 2:59:59 PM
Figure 27
Figure 28
Push the trigger group pins through

the receiver.
Lift the trigger group from the receiver.

The Lightning Trigger and bolt can be removed if the action becomes
excessively dirty or wet. If this occurs, disassemble the action for a
complete cleaning as explained in the following sections. The trigger
group and bolt assembly of your Maxus shotgun are designed to be
removed in the field, without special tools.
Disassembly of the action involves the removal of the bolt assembly
and the trigger group. Disassembly beyond this point should only be
performed by a qualified gunsmith.
4 Perform any cleaning of the parts and receiver cavity as necessary.

We suggest cleaning the trigger group with a quality aerosol gun
solvent. Allow it to dry and then very lightly oil the moving parts.
Notice! DO NOT DISASSEMBLE THE TRIGGER GROUP BEYOND
THIS POINT.
r e i n s ta l l at i o n o f t h e t r i g g e r g r o u p
removing the trigger group
1 Make sure the bolt is in the forward position.
1 Place the bolt in the forward position by holding the operating

handle and depressing the bolt release button.
2 Insert the trigger group into the receiver. Align the holes in the
trigger group with the holes on each side of the receiver.

Bolt release BUTTON WITHOUT THE BARREL INSTALLED. If the bolt is
3 Reinsert the trigger guard pins and gently tap them into place
with a plastic or wooden mallet, again using caution not to
scratch the receiver.
2 Use a punch or similar object to push inward on the trigger guard

pins, taking care not to scratch the receiver (Figure 27, page 41).
Trigger group pins may be removed from either side of the
receiver. Push the trigger group pins through the receiver. Pull on
them from the opposite side to remove them.
3 Grasp the trigger guard and pull it up and out of the receiver
(Figure 28, page 41).
40
r e m o va l o f t h e b o lt a s s e m b ly
BEFORE removing the bolt assembly, place the safety in the on
safe position. open the action and make certain YOUR shotgun
IS completely UNLOADED. Keep the muzzle pointed in a safe
direction. Failure to follow these warnings could result in
41
6/22/09 2:59:59 PM
Figure 31
Figure 32
The bolt and bolt slide can be separated

for cleaning.
The bolt shown assembled.

1 Remove the barrel, gas piston, piston sleeve and piston sleeve
spring as explained previously.
2 Prior to removing the bolt assembly, it is preferred to first remove
the trigger group, as explained previously.
3 Carefully place the bolt in the forward position by holding back on
the operating handle and depressing the bolt release button.
Bolt release BUTTON WITHOUT THE BARREL INSTALLED. If the bolt is
Figure 29
Figure 30
4 Remove the operating handle by pulling the operating handle

outward (Figure 29).
5 Slide the bolt assembly forward and out of the receiver (Figure 30).
6 The bolt and bolt slide can now be separated for cleaning (Figure 31).
Perform cleaning of the bolt and receiver cavity as necessary.
Notice! DO NOT DISASSEMBLE THE bolt assembly BEYOND THIS POINT.
r e i n s ta l l i n g t h e b o lt a s s e m b ly
1 Reassemble the bolt and bolt slide (Figure 32).

2 Place a few drops of oil in the
grooves in the bolt to lubricate
the bolt slide rails (Figure 3,
page 11).
Figure 33
3 Align the rails on the bolt slide

with the grooves in the receiver.
Press the bolt release button and
slide the bolt assembly into the
receiver, bolt slide link end first.
Pull outward to remove the bolt handle.
42
Slide the bolt forward and out of the receiver.
4 Ensure the bolt slide link fits into

the socket in the recoil spring
follower (Figure 33).
Guide the bolt slide link into its socket in the

recoil spring follower.
43
6/22/09 2:59:59 PM
5 Replace the operating handle by inserting it in its slot in the bolt.

6 Open and close the action several times to make sure the bolt slide
link and recoil spring follower are properly engaged.
Bolt release BUTTON WITHOUT HAVING THE BARREL INSTALLED.
DAMAGE WILL RESULT TO THE RECEIVER and operating handle.
C LEANING THE A C TION
1 When the action becomes excessively dirty, remove the trigger

group and bolt assemblies from the receiver as explained under
Removal of the Trigger Group (page 40) and Removal of the
Bolt Assembly (page 42). Clean with a gun solvent as necessary,
using a nylon brush to loosen any caked-on grime.

Wipe the receiver cavity clean. Lightly oil the cavity and wipe it dry.
No further disassembly is required for cleaning.
2 Reassemble the trigger group, bolt assembly, gas system and the
barrel to the receiver as explained previously. Then wipe all exposed
metal surfaces with an oiled cloth, making sure to wipe clean all
finger marks where moisture could accumulate.
3 The barrel and action should be inspected thoroughly to be
certain no cleaning patches have been inadvertently left in them.
L u b r i c a t i n g t h e Ac t i o n t u b e a n d s p r i n g
BEFORE lubricating the action tube and spring, place the
safety in the on safe position. open the action and make
certain YOUR shotgun IS completely UNLOADED. Keep the muzzle
pointed in a safe direction. Failure to follow these warnings
could result in serious injury or death.
WEAR EYE PROTECTION WHEN DISASSEMBLING AND lubricating YOUR

Keep all ammunition away from the cleaning area. Never test
the mechanical function of your shotgun with live
ammunition. Failure to follow these warnings could result in
If you frequently use your shotgun in inclement weather conditions,

oiling the action tube and spring will aid in maintaining the
performance and reliability of your firearm.
1 Remove the recoil pad and buttstock as explained previously.
2 Place a few drops of high-quality lightweight gun oil in the opening
in the rear of the action tube (Figure 34).
do not attempt to remove the action spring from the action
tube. the action tube is easily damaged and The action spring is
under spring tension. Failure to follow this warning could
result in serious injury or damage your shotgun.
3 Hold the shotgun with the

muzzle down. Rotate the
shotgun and cycle the action
using the bolt handle to
operate the action several
times to evenly disperse the
oil on the spring and inside
the action tube.
Figure 34
Place a few drops of oil in the opening in the

action tube.
44
45
6/22/09 3:00:00 PM
notice! Do not use excessive lubricant. Using too much

lubricant can interfere with the functioning of your shotgun.
Do not spray solvent inside the action tube.
4 Carefully rest the shotgun vertically on a rag with the action tube
down to allow any excess oil to drain out of the action tube. Wipe
away any excess oil.
5 Lightly lubricate the external surface of the action tube.
6 Install the buttstock and recoil pad as explained previously.
NOTICE! Do not TAKE YOUR firearms ACTION APART beyond what
is explained in this owners manual. This is a specialized,
finely fitted mechanism; any attempt to disassemble the inner
mechanism may mar it for life. It is unnecessary, and may do
damage to the inner mechanism to disassemble it for routine
cleaning and oiling. Of course, misfortunes (such as dropping
your firearm in water) require appropriate attention, and in
such circumstances we recommend you immediately take your
firearm to a qualified gunsmith.
Models with special finisheS

As with any firearm, the only way to preserve its pristine condition and
collector appeal is to never handle or fire it, which in turn would
deprive you of much of the enjoyment that comes with owning a fine
Browning firearm.
While special finishes such as engraving and gold plating greatly
enhance the aesthetic appeal of your shotgun, please be aware that
they are no more durable, and in some cases may even be slightly less
durable than more common firearm finishes.
As you use your shotgun, you can expect special finishes to wear in
much the same manner as any other firearm finish. These marks are
the honest product of the hours spent enjoying your firearm and each
scuff and scratch will probably have a good story to go along with it.
m a i n t e n a n c e o f o i l f i n i s h s t o ck s
Keeping the oil-finished wood surface on your firearm looking its
best requires only a small amount of maintenance. When the surface
becomes spotted or dull, the affected area(s) can be treated using
rubbing alcohol on a soft, lint free cloth and allowed to dry. A small
amount of a linseed oil-based finish, such as Watco Danish Oil Finish,
Deft Danish Oil Finish, or Formbys Tung Oil Finish should then be
applied to the surface of the wood with a soft, lint free cloth according
to the manufacturers instructions. To treat the checkering, a small
amount of oil-based finish can be applied and then distributed evenly
using a toothbrush or other soft bristled brush.
46
47
6/22/09 3:00:00 PM
service or repair
If your firearm should require service or repairs, we suggest you first
contact a local recommended Browning Firearms Service Center.
To locate a service center visit browning.com, contact our Customer
Service Department or your Browning firearms dealer for the address
of the Service Center nearest you. Otherwise, you may send your
firearm directly to our Service Department in Arnold, Missouri.
Parts listings, Firearm Service Center lists, service procedures, service/
repair form and general product information are also found on the
internet at: browning.com. For technical questions about your firearm
or service, contact:
United States customers contact:
Browning Service Department
One Browning Place
Arnold, MO 63010-9406
Phone: (800) 322-4626
Canadian customers contact:

Browning Canada Sports Ltd/Lte
5583 Chemin St-Franois
St-Laurent, Quebec H4S 1W6
Phone: (514) 333-7261
When returning your firearm for servicing, you must do the following:
1 Be sure it is completely unloaded.
2 Remove the scope or other optics.
3 Package it securely in a cardboard container.
4 Enclose the service/repair form available at browning.com or a
letter that clearly describes the trouble experienced, the
ammunition used and the repairs desired. Also include your name
and a daytime phone number where you can be reached.
5 If convenient, send a copy of the service/repair form or letter
to us separately.
6 Never return ammunition with your firearm. It is against postal
and most commerce regulations.
48
6/22/09 3:00:00 PM
08-121-BFA_Maxus OM.indd 50
browning.com
BROWNING US: Morgan, Utah 84050-9326
BROWNING CANADA: Browning Canada Sports Ltd/Lte, St-Laurent, Quebec H4S 1W6
BROWNING INTL: Parc Industriel des Hauts-Sarts, B-4040 Herstal, Belgium
NEU0903.1/08121
6/22/09 3:00:00 PM

Maxus Manual

Uploaded by

Copyright:

Available Formats

Maxus Manual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Maxus Manual

Uploaded by

Copyright:

Available Formats

08-121-BFA_Maxus OM.

Important operating instructions for:

You are Responsible for Firearms Safety.................................................2

If you have any questions about your new firearm, this

08-121-BFA_Maxus OM.indd 2-1

You Are Responsible For Firearms Safety

Failure to follow any of the following warnings could result

Some firearms do not have a mechanical safety. Many target

There is no excuse for careless or abusive handling of any firearm.

While it is a good idea to test your firearms mechanical safety

Please read and understand all of the cautions, warnings, notices,

3 Whenever you handle any firearm, or hand it to someone,

As a gun owner, you accept a set of demanding responsibilities. How

1 ALWAYS KEEP THE MUZZLE OF YOUR firearm POINTED IN A SAFE

08-121-BFA_Maxus OM.indd 2-3

4 Always WEAR Ear AND Eye PROTECTION WHEN SHOOTING.

Wear shooting glasses to protect your eyes from flying particles.

Always wear eye protection when disassembling and cleaning any

5 Keep all firearms unloaded during transport, even

08-121-BFA_Maxus OM.indd 4-5

BEFORE CHECKING FOR A BARREL OBSTRUCTION, BE CERTAIN

After assuring yourself that the firearm is completely unloaded,

10 Be alert to the signs of ammunition malfunction. if you

12 examine every shell you put in your firearm.

08-121-BFA_Maxus OM.indd 6-7

17 BE SURE OF YOUR TARGET AND BACKSTOP, particularly

23 read AND HEED ALL WARNINGS in this owners manual, on

DO NOT, UNDER ANY CIRCUMSTANCES, ALTER THE TRIGGER, SAFETY

08-121-BFA_Maxus OM.indd 8-9

Front Sight Bead

Speed Lock Lever

Piston Sleeve Spring

Various exposed metal parts of

Be especially careful when cleaning firearms with camouflage,

08-121-BFA_Maxus OM.indd 10-11

Always keep the safety in the on safe position unless

The safety shown in the on safe position.

The safety shown in the off safe position.

Press and hold the release button while lifting

Align the push rod with the slot in the receiver.

The safety can be reversed from right- to left-handed by a

08-121-BFA_Maxus OM.indd 12-13

Notice! NEVER ALLOW THE ACTION TO SLAM CLOSED BY PRESSING

2 Remove the forearm from the magazine tube by pressing and

1 Lock the bolt rearward by pulling the operating handle fully to

2 Remove the forearm as explained previously.

Slide the barrel and piston over the magazine

Ensure the forearm is secured correctly, with

Notice! Do not squeeze hard on the open rear end of a wood

3 For cleaning, remove the barrel and gas system by sliding

08-121-BFA_Maxus OM.indd 14-15

a 3" chamber. Doing so can result in a buildup of dangerously

The most certain way to bulge or rupture a shotgun barrel is to load

08-121-BFA_Maxus OM.indd 16-17

three-shot adapter (Plug)

The Maxus is delivered with the magazine three-shot adapter (plug)

1 Lock the bolt rearward by pulling the operating handle fully

2 Remove the forearm as explained previously.

Use a key or small screwdriver to press in

Remove the three-shot adaptor.