Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

Pds Hempadur Mastic 45880

Download as pdf or txt
Download as pdf or txt
You are on page 1of 3

Product Data

HEMPADUR MASTIC 45880


45880: BASE 45889: CURING AGENT 95880

Description:

HEMPADUR MASTIC 45880 is a two-component polyamide adduct cured, high solids, high build
epoxy paint. It forms a hard and tough coating, has good wetting properties and low temperature
curing.

Recommended use:

As a selfprimed, surface tolerant paint system or as an intermediate or finishing coat in heavy duty
paint systems where low VOC and high film build are required.
Multipurpose coating as per specification for maintenance and minor repairs in immersed areas
including ballast tanks and underwater hull specifically in those cases where a need for few products
outweighs more specialised coatings.
Can be specified where extended recoating properties for polyurethane topcoats are requested
(typically travel coating). May be used directly on cured zinc silicate (GALVOSIL products) or spraymetallized surfaces to minimize popping.

Service temperature:

Maximum, dry exposure only: 120C/248F.

Certificates/Approvals:

In accordance with Aramcos specification APCS 1, APCS 12, APCS 26 and 26T.
Complies with Section 175.300 of the Code of Federal Regulations Title 21 Dry Foodstuff. Consult
Hempel for details.
Classified as class 1 material according to BS 476: Part 7: 1997 (fire testing).
Approved as a low flame spread material when used as part of a predefined paint system. Please refer
to Declaration of Conformity on www.Hempel.com for further details.
Complies with EU Directive 2004/42/EC: subcategory j.

Availability:

Part of Group Assortment. Local availability subject to confirmation.

PHYSICAL CONSTANTS:
Shade nos/Colours:
Finish:
Volume solids, %:
Theoretical spreading rate:
Flash point:
Specific gravity:
Dry to touch:
Fully cured:
VOC content:

12170* / Grey.
Semi-gloss
80 1
6.4 m2/l [256.6 sq.ft./US gallon] - 125 micron/5 mils
39 C [102.2 F]
1.5 kg/litre [12.1 lbs/US gallon]
12 approx. hour(s) 10C/50F
14 day(s) approx. hour(s) 10C/50F
216 g/l [1.8 lbs/US gallon]

*Wide range of colours available via Hempel's MULTI-TINT system.


The physical constants stated are nominal data according to the HEMPEL Group's approved formulas.

APPLICATION DETAILS:
Version, mixed product:
Mixing ratio:
Application method:
Thinner (max.vol.):
Pot life (Airless spray):
Pot life (Brush):
Nozzle orifice:
Nozzle pressure:
Cleaning of tools:
Indicated film thickness, dry:
Indicated film thickness, wet:
Overcoat interval, min:
Overcoat interval, max:
Safety:

45880
BASE 45889: CURING AGENT 95880
3 :1 by volume
Airless spray / Brush
< 5% HEMPEL'S THINNER 08450, depending on purpose (see REMARKS overleaf)
1 approx. hour(s) 20C/68F
2 approx. hour(s) 20C/68F
0.017 - 0.023 " (According to separate APPLICATION INSTRUCTIONS)
250 bar [3625 psi]
HEMPEL'S TOOL CLEANER 99610
125 micron [5 mils] (see REMARKS overleaf)
150 micron [6 mils]
see REMARKS overleaf
see REMARKS overleaf
Handle with care. Before and during use, observe all safety labels on packaging and paint containers,
consult HEMPEL Safety Data Sheets and follow all local or national safety regulations.

Not available.

Date of issue: February 2014


-

Page: 1/3

Product Data Sheet

HEMPADUR MASTIC 45880


SURFACE PREPARATION:

New steel: Abrasive blasting to minimum Sa 2 (ISO 8501-1:2007) with a surface profile
corresponding to Rugotest No. 3, N9a to N10, preferably BN9a to BN10, Keane-Tator Comparator, 2.0
G/S or ISO Comparator, Medium (G).
Zinc silicate painted or spray-metallized surfaces: Remove oil and grease, etc. with suitable
detergent. Remove salt and other contaminants by (high pressure) fresh water cleaning. Zinc salts
(white rust) must be removed by high pressure hosing combined with rubbing with a stiff nylon brush if
necessary. It is recommended to recoat spray-metallized surfaces as soon as possible to avoid
possible contamination.
Concrete: Remove slip agent and other possible contaminants by emulsion washing followed by high
pressure hosing with fresh water. Remove scum layer and loose matter to a hard, rough and uniform
surface, preferably by abrasive blasting, possibly by other mechanical treatment or acid etching. Seal
surface with suitable sealer, as per relevant painting specification.
Repair and maintenance: Remove oil and grease etc. thoroughly with suitable detergent. Remove
salts and other contaminants by high pressure fresh water cleaning. Clean damaged areas thoroughly
by power tool cleaning to minimum St 2 (spot-repairs) or by abrasive blasting to min. Sa 2, preferably
to Sa 2 (ISO 8501-1:1988). Improved surface preparation will improve the performance of the
product. As an alternative to dry cleaning, water jetting to sound, well adhering coat and/or to steel.
Intact coat must appear with roughened surface after the water jetting. By water jetting to steel,
cleanliness shall be: Wa 2 -Wa 2 (atmospheric exposure) / minimum Wa 2 (immersion) (ISO
8501-4:2006). Acceptable flash-rust degree before application: maximum M (atmospheric exposure) /
M, preferably L (immersion) (ISO 8501-4:2006).
Feather edges to sound and intact areas. Dust off residues. Touch up to full film thickness. On pitcorroded surfaces, excessive amounts of salt residues may call for high pressure water jetting, wet
abrasive blasting or, alternatively, dry abrasive blasting, high pressure fresh water hosting, drying, and
finally dry abrasive blasting again.

APPLICATION CONDITIONS:

Apply only on a dry and clean surface with a temperature above the dew point to avoid condensation.
Use only where application and curing can proceed at temperatures above: - 5/23F, preferably
above 0C/32F. The temperature of paint itself should be 15C/59F or above. In confined spaces
provide adequate ventilation during application and drying.

PRECEDING COAT:

None, or as per specification.

SUBSEQUENT COAT:

None, or as per specification.

REMARKS:
VOC - EU Directive 2004/42/EC:

Product
4588012170

Not available.

As supplied
216 g/l

5 vol. % thinning
248 g/l

Limit phase II, 2010


500 g/l

For VOC of other shades, please refer to Safety Data Sheet.

Weathering/service temperatures: The natural tendency of epoxy coatings to chalk in outdoor exposure and to become more sensitive to
mechanical damage and chemical exposure at elevated temperatures is also reflected in this product.
Application(s):
Application onto zinc silicate or spray-metallized surfaces (thinning): It is recommended to apply the
paint by using a "mist-coat" procedure provided the paint temperature is approximately above:
20C/68F. A thin, diluted coat is applied (the mist coat) and after a few minutes, a second coat is
applied in the full specified film thickness If the paint temperature is below: 20C/68F, thinning (max
15%) may be required.
Film thicknesses/thinning:
May be specified in another film thickness than indicated depending on purpose and area of use. This
will alter spreading rate and may influence drying time and recoating interval. Normal range dry is:
125-200 micron/5-8 mils. May be specified in lower film thickness for which purpose additional thinning
is required, please see separate APPLICATION INSTRUCTIONS. Avoid application of excessive
film thicknesses.
Shades:
The product is also available in a Micaceous Iron Oxide (MIO) pigmented shade (Shade no. 12430
reddish grey ) and in aluminium pigmented shades (Shade nos. 19870 - dark alu and 19000 - light alu).
Overcoating:
Overcoating intervals related to later conditions of exposure: If the maximum overcoating interval is
exceeded, roughening of the surface is necessary to ensure intercoat adhesion.
Before overcoating after exposure in contaminated environment, clean the surface thoroughly with
high pressure fresh water hosing and allow drying.
A specification supersedes any guideline overcoat intervals indicated in the table.
Environment

Atmospheric, medium

Surface temperature:

Date of issue: February 2014


-

0C (32F)

10C (50F)

20C (68F)

Min

Max

Min

Max

Min

Max

HEMPADUR

63 h

Ext.

21 h

Ext.

7h

Ext.

HEMPATEX

45 h

4.5 d

15 h

36 h

5h

12 h

HEMPATHANE

63 h

Ext.

21 h

Ext.

7h

Ext.

Page: 2/3

Product Data Sheet

HEMPADUR MASTIC 45880


Environment

Immersion

HEMPADUR

4.5 d

90 d

36 h

60 d

12 h

30 d

NR = Not Recomended, Ext. = Extended, m = minute(s), h = hour(s), d = day(s)

Overcoating intervals:

A specification supersedes any guideline overcoat intervals indicated in the table.

Note:

HEMPADUR MASTIC 45880

ISSUED BY:

HEMPEL A/S
4588012170

X Move PDS Disclaimer to Second page


This Product Data Sheet supersedes those previously issued.
For explanations, definitions and scope, see Explanatory Notes available on www.hempel.com. Data, specifications, directions and recommendations
given in this data sheet represent only test results or experience obtained under controlled or specially defined circumstances. Their accuracy,
completeness or appropriateness under the actual conditions of any intended use of the Products herein must be determined exclusively by the Buyer
and/or User.
The Products are supplied and all technical assistance is given subject to HEMPEL's GENERAL CONDITIONS OF SALES, DELIVERY AND SERVICE, unless
otherwise expressly agreed in writing. The Manufacturer and Seller disclaim, and Buyer and/or User waive all claims involving, any liability, including but
not limited to negligence, except as expressed in said GENERAL CONDITIONS for all results, injury or direct or consequential losses or damages arising
from the use of the Products as recommended above, on the overleaf or otherwise. Product data are subject to change without notice and become void
five years from the date of issue.

Date of issue: February 2014


-

Page: 3/3

Product Data Sheet

You might also like