Design Exam (1) SHFHSDHSDH

PREBOARD
DESIGN AND CONSTRUCTION

TOLENTINO AND ASSOCIATES
(Note There are few questions whose answers are not in the choices. Just
Answer E. )
S -1
Given the figure shown.
1.
a.
2.
a.
3.
a.
4.
a.
Reaction at A is
400N
b. 445 N
c. 457 N
d. 479 N
The Reaction at B is
89 N
b. 100 N
c. 110 N
d. 114 N
The tangential deviation of B with respect to a tangent drawn at A.
1672/EI b. 1967/EI c. 2011/EI d. 2311/EI
The slope at B is
89.58/EI b. 87.33/EI c. 85.23/EI d. 82.55/EI
S-2
The beam shown weighs 30 N/m.
5.
a.
6.
a.
7.
a.
8.
a.
9.
a.
The vertical reaction at A

422 N
b. 322 N
c. 201 N
d. 246 N
The tension at B
308 N
b. 352 N
c. 442 N
d. 588 N
The Horizontal Reaction at A.
409.22 N b. 390.44 Nc. 372.41 N d. 345.11 N
The Resultant reaction at A
427.41 N
b. 477.47 Nc. 489.22 N d. 502.41 N
The angle that Reaction at A makes with the horizontal.
31.010 b. 34.220
c. 37.410
d. 3.770
S-3
Given the beam shown. The 100 kN load acts on the centroid of the cross
section.
10. The flexular stress at A.

a. 64.95 Mpa
b. 66.31 Mpa
c. 68.22 Mpa
d.
70.03 Mpa
11. The axial stress at A
a. 3 Mpa
b. 5 Mpa
c. 7 Mpa
d. 9 Mpa
12. The total normal stress at A
a. 55.23 Mpa
b. 57.21 Mpa
c. 69.95 Mpa
d.
73.55 Mpa
13. The shearing stress at A
a. 9.743Mpa
b. 11.412 Mpa
c. 12.455 Mpa
d.
13.111 Mpa
14. The principal stress at A
a. 67.41 Mpa
b. 71.33 Mpa
c. 76.22 Mpa
d.
79.28 Mpa
15. The angle that the principal stress makes with the horizontal
a. 5.67 deg
b. 7.78 deg
c. 8.91 deg
d. 9.89 deg
S-4
The 3 hinged arc shown is subjected to the two concentrated forces
shown.
16. The vertical reaction at C is
a. 7.312kN
b. 6.234 kN
c. 5.231
kN
d. 4.348 kN
17. The horizontal reaction at C is
a. 3 kN
b. 4 kN
c. 5 kN
d. 6
kN
18. The reaction at B
a. 16.12 kN
b. 18.33 kN
c. 24.44 kN
d. 27.11 kN
S-5
A truck and a trailer combination crossing a 12 m span has axle loads as
given.
19. The distance of the resultant load from the 10 Kn load is

a. 2 m
b. 3 m
c. 4 m
d. 5 m
20. The maximum shear developed in the beam.
a. 30 kN
b. 33 kN
c. 39 kN
d. 45 kN
21. The maximum moment in the beam is
a. 78.22 kNm
b. 82.36 kNm
c. 96.12 kNm
104.17 kNm
d.
S-6
The 10 meter ladder weighing 35 kg is resting on a horizontal floor at A
and on the wall at B making an angle of 60 deg from the horizontal. The
coefficient of friction between the ladder and the wall ( and the ground
and the ladder ) is 0.25 .
A man of mass 72 kg climbs the ladder.
22. Determine the Normal reaction at the wall.
a. 25.176 kG
b. 27.441 kG
c. 29.417 kG
d.
32.114 kG
23. Determine the resultant reaction at the wall.
a. 233.41 N
b. 254.58 N
c. 266.29 N
d. 287.11 N
24. Determine the normal reaction at the ground.
a. 89.267 kG
b. 100.706 kG
c. 115.241 kG
d.
132.221 kG
25. Determine the resultant reaction at the ground.
a. 1018.33 N
b. 1233.75 N
c. 1342.41 N
d.
1661.22 N
26. Determine the distance x from the from the bottom of the ladder to
which the man cal climb without causing the ladder to slip at its lower end
A.
a. 4.5 m
b. 5.2 m
c. 5.8 m
d. 6 m
S-7
A simply supported beam 10 m long has an overhang of 2 m at the left
support. If a highway uniform load of 9.35 kN/m and a concentrated load
of 116 kN passes trough the beam, compute the following based on the
influence line on the maximum shear at midspan.
27. The ordinate of the IL for max shear at midspan 4 m from A.

a. -0.2
b. -1.7
c. 2.4
d. 3.1
28. The length of the beam where uniform load can produce maximum
positive shear in the beam at the midspan.
a. 4
b. 7
c. 8
d. 11
29. The maximum positive shear at the midspan.
a. 71.56 kN
b. 61.22 kN
c. 58.21 kN
d. 42.88 kN
30. The ordinate of the influence line for the maximum bending moment
at the midspan 4 m from A.
a. 6
b. 4
c. 3
d. 1
31. The value of the maximum positive bending moment at the midspan.
a. 389.212 kN m b. 406.875 kN m c. 412.441 kN m d. 422.412 kN m
S-8
A 9 meter high retaining wall is laterally supported at the top and fixed at
the base. The wall resists active earth pressure increasing from 0 at the
top to 52 kN/m at the base per meter length along the longitudinal axis.
32. The design moment at the base is
a. 455.5 kNm
b. 423.1 kNm
c. 301.2 kNm
d.
280.8 kNm
33. The lateral support from the top
a. 46.8kN
b. 49.2 kN
c. 51.9 kN
d. 58.1 kN
34. If the lateral support at the top is removed, the design moment is
a. 622 kNm
b. 688 kNm
c. 702 kNm
d. 710 kNm
The entrance of a warehouse has a roof that supports a roof load of 8
kN/m. The supports B and C are considered simply supported.
35. The vertical reaction at the column is

a. 37.5 kN
b. 39.98 kN
c. 41.26 kN
d. 44.11 kN
36. The vertical reaction at C is
a. 19.4 kN
b. 22.5 kN
c. 25.1 kN
d. 30.1 kN
37. Maximum negative moment at AC.
a. 7 kNm
b. 9 kNm
c. 11 kN m
d. 13 kNm
38. Maximum positive moment at AC.
a. 25.58 kNm
b. 31.64 kNm
c. 33.01 kN m
36.22 kNm
39. Location of the point of inflection at AC from A.
a. 1.092 m
b.1.567 m
c. 1.872 m
d. 1.987 m
d.
S-9
A water tank 3 meter in diameter and 6 meter high is made of steel
having a thickeness of 12 mm.
40. When the tank is filled with water, determine the circumferential
stress.
a. 7.36 Mpa
b. 9.82 Mpa
c. 11.23 Mpa
d.
12.66 Mpa
41. Determine the longitudinal stress when it is filled with water.
a. 2.41 Mpa
b. 3.68 Mpa
c. 4.76 Mpa
d. 5.54
Mpa
S- 10
A hollow circular pole 6 mm thick with a 300 mm ouside diameter and a
height of 3 meter weighs 150 N/m. The pole is subjected to the following
loads.
P = 3 kN and e = 100 mm from the centroid of the section. Lateral force
of 0.45 kN acts at the top of the pole.
42. The maximum compressive stress at the base due to the vertical load
plus the weight of the pole.
a. 4.22 Mpa
b. 3.66 Mpa
c. 2.09 Mpa
d.1.37 Mpa
43. The maximum tensile stress at the base due to lateral and vertical
loads and the weight of the pole.
a. 2.41Mpa
b. 3.51 Mpa
c. 4.89 Mpa
d. 5.77 Mpa
44. BONUS-----If the hollow pole is replaced by a solid wood pole of 250
mm diameter, determine the maximum shear stress in the pole.
a.3.091 Mpa
b. 1.781 Mpa
c. 0.012 Mpa
d.
0.000
S -11
A barge shown diagramatically supports a load of W1 and W2 for every
one meter strip along the longitudinal section.
44.Bonus!--- Find total legth L so that the upward pressure is uniform and
that the barge remains horizontal
a. L = 8 m
b. L = 3 m
c. L = 15 m
d. L = 17 m
45. The shear at 3 meter from the left end when upward pressure q = 72
kN/m.
a. 1.03 kN
b. 1.67 kN
c. 219 kN
d. 241 kN
46. Distance from the left end where Shear = 0 when q = 87 kN/m
a. 3 m
b. 4 m
c. 5 m
d. 6
m
S -12
The tensile member shown is 50 mm by 75 mm and subjected to a load of

P = 200 kN. The plane AA makes an angle of 150 with the a axis.
47. The tensile stress at section AA.
a. 41.98 Mpa
b. 44.11 Mpa
c. 49.76 Mpa
d.
52.11 Mpa
48. The shear stress on Plane AA.
a. 10.31 Mpa
b. 11.98 Mpa
c. 13.33 Mpa
d.
15.02 Mpa
S - 13
A load W is to be lifted using the crane shown. x1 = 10 m, x2 = 8 m .
Weight of the crane is 2 kN.
49. The force at cable AC is

a. 19.34 kN
b. 24.91 kN
c. 27.98 kN
d. 29.12 kN
50. The reaction at B
a. 33.11 kN
b. 43.35 kN
c. 46.11 kN
d. 48.21 kN
51. Largest force that can be lifted if maximum force AC= 50kN
a. 40.11kN
b. 42.15 kN
c. 45.12 kN
d. 47.12 kN
S -14
A simply refinforced concrete beam reinforced for tension has a width of

300 mm and a total depth of 600 mm. It is subjected to external Moment
Mu = 540kN m.
fc = 28 Mpafy = 280 MpaEs = 200 Gpa
52. The balanced steel ratio is
a. 3.981%
b. 4.926%
c. 6.011%
d. 7.221%
53. The depth a in terms of d if = 1/2 balance Use = 0.9
a. 22.11%
b. 25.45%
c. 28.11%
d. 30.71%
54. The minimum effective depth is
a. 583.21 mm
b.421.44 mm
c. 341.22 mm
d.
301.29 mm
S -15
The beam is to be analyzed using moment distribution.
55. The Fixed End Moment at D for span CD is

a. 7.11kNm
b. 8.23 kN m
c. 9.28 kN m
11.21 kN m
56. The Distribution Factor at C for member BC is
a. 0.667
b. 2.031
c. 3.331 m
d. 4.127 m
d.
57. Using Three Moment Equations , the bending Moment Equations
6 A b
the
L
for member
CD if you consider span BCD is
a. 85.33kN m2
b. 80.12 kN m2
2
73.11 m
58. The bending moment at B is
a. 11.41 kN m
b. 12.86 kN m
18.21 kN m
c. 78.44 kN m2
d.
c. 15.22 kN m
d.
S -16
A W 420 x 85 steel beam is fully restrained with a uniformly distributed
load of 25 Kn/m. The beam has a span of 10 m.
Properties:
A = 10839 mm2
bf = 180 mm
tf = 18 m
tw = 11 mm
d = 420 mm
59. The actual uniform load carried by the beam ( include its weight )
a. 25.834kN/m b. 26.878 kN/m
c. 27.451 kN/m
d. 28.221
kN/m
60. The maximum moment carried by the beam.
a. 312.11 kN m
b. 289.56 kN m
c. 266.77 kN m
d.
215. 28 kN m
61. The maximum bending stress
a. 244.11 Mpa
b. 213.41 Mpa
c. 199.12 Mpa
d.
145.84 Mpa
62. The maximum web shear stress
fv = V/( d tw )
a. 27.96 Mpa
b. 31.22 Mpa
c. 34.11 Mpa
d.
37.22 Mpa
63.The maximum horizontal shear stress
a. 30.22 Mpa
b. 33.09 Mpa
c. 35.32 Mpa
d.
38.22 Mpa
S -17
Given the figure shown.
64. The tensile stress in the body of the bolt.

a. 62.11 Mpa
b. 67.22 Mpa
c. 70.64 Mpa
d.
77.41 Mpa
65. The Tensile stress at the root of the threads
a.91.22Mpa
b. 94.11 Mpa
c. 99.47 Mpa
d.106.22 Mpa
66. Find the compressive stress at the head as the bolt bears on the
surface to resist the tensile load.
a. 36.21 Mpa
b. 40.33 Mpa
c. 43.51 Mpa
d.
47.23 Mpa
S -18
The pin jointed assembly supports a billboard 2 m high x 4 n wide on

each end. The total weight of the billboard is 24 kN. H = 1 m and = 600.
Wind pressure q = 1.44 KpA
Wind pressure coefficient C = 1.2
67. The resultant wind load is

a. 13.824 kN
b. 15.214 kN
c. 17.226 kN
c.
20.112 kN
68. The axial force at AB is
a. 12.41 kN
b. 14.21 kN
c. 16.02 kN
d. 18.21 kN
69. The axial force at BC is
a. 28.12 kN
b. 31.98 kN
c. 34.21 kN
d. 37.77 kN
70. The vertical reaction at A is
a. 7.21 kN
b. 8.01 kN
c. 9.81 kN
d. 11.31 kN
71. The horizontal reaction at C is
a. 27.7 kN
b. 33.1 kN
c. 37.2 kN
d. 39.1 kN
72. If the strut AB is replaced by 16 mm diameter cable, determine the
normal stress in the cable.
a. 66.12 Mpa
b. 69.34 Mpa
c. 72.11 Mpa
d.
79.68 Mpa
S-19
The figure shows a semicircular arc with the given load.
73. The shear at D is

a. 0.03 kN
b. 0.84 kN
74. The moment at D is
c. 1.44 kN
d. 2.42 kN
a. 4.77 kN m
b. 3.12 kN m
c. 2.14 kN m
1.12 kN m
75. The axial force at D is
a. 1.12 kN
b. 2.44 kN
c. 4.12 kN
d. 4.98 kN
d.
S-20
When the columns at E and H of the floor framing plan are deleted, girder
BEHK becomes a one span fixed ended beam supporting DEF and beam
GHI at H. The following loads on girder BEHK are as follows.
Concentrated load at E = 266 kN
Concentrated load at H = 266 Kn
Uniform load throughout its length = 5Kn/m
Hint: Consider BK as beam fixed at B and K with the given loads.
76. Compute the reactive moment at B.

a. 466.67 kN m
b. 489.12 kN m
c. 522.11 kN m
534.29 kN m
77. Compute the reactive moment at K.
a. 378.48 kN m
b. 466.67 kN m
c. 522.11 kN m
531.88 kN m
78. The maximum shear in the beam
a. 201.49kN
b. 284.75 kN
c. 304.88 kN
387.11 kN
79. The maximum positive bending moment in the beam.
a. 605.44 kN m
b. 672.88 kN m
c. 700.16 kN m
741.41 kN m
S -21
d.
d.
d.
d.
P1 = 1.8 kN
P2 = 0.9 kN P3 = 0.45 kN = 300 = 450
80. The magnitude of the resultant of the 3 forces.

a. 2.455 kN
b. 3.412 kN
c. 4.791 kN
d. 5.012 kN
81. The angle that the resultant makes with the horizontal
a. 56.120
b. 59.650
c. 67.110
d. 71.410
82. The vertical reaction at B.
a. 1.06 kN
b. 2.41 kN
c. 3.01 kN
d. 3.78 kN
83. The horizontal component of the reaction at B.
a. 5
b. 3
c. 1
d. 0
S-22
The suspended girder shown is supported by a series of hangers uniformly
spaced along the parabolic cable.
84. The minimum tension is

a. 160 kN
b. 170 kN
c. 180 kN
d. 190 kN
85. The maximum tension is
a. 101.412 kN
b. 134.211 kN
c. 178.885 kN
d.
189.412 kN
86. The safe uniform load that the cable can support if maximum tension
is 250kN.
a. 13.976kN/m b. 16.221 kN/m
c. 18.412 kN/m
d. 19.661
kN/m
87. The length of the cable is
a. 11.232 m
b. 13.441 m
c. 16.644 m
d.
18.412 m
S-23
A concrete mixture has a ratio of 1:2:4 by mass. The water requirements
is 24 liters per bag of cement.
Weight of Cement = 40 kg/bag.
Materials
SG
cement
3.33
sand
2.5
gravel
2.67
88. The volume of cement per bag
a. 0.012 m3
b. 1.441 m3
c. 2.455 m3
89. The volume of sand for 1 bag of cement
a. 3.451 m3
b. 2.411 m3
c. 1.442 m3
90. The volume of gravel for 1 bag of cement is
a. 2.44 m3
b. 2.04 m3
c. 1.44 m3
91. The total volume of concrete is
a. 0.128 m3
b. 1.331 m3
c. 2.412 m3
d. 3.011 m3
d. 0.032 m3
d. 0.06 m3
d. 3.331 m3
S -24
A 5 kg block is at rest at time t = 0 and is acted upon by a horizontal force
P that varies with time as shown.
92. The initial acceleration of the block is

a. 8.37 m/s2
b. 3.41 m/s2
c. 4.44 m/s2
2
m/s
93. The velocity of the block after 5 seconds
a. 22.441 m/s
b. 34.917 m/s
c. 36.428 m/s
41.221 m/s
94. The distance travelled after 5 sec is
a. 97.438 m
b. 103.442 m
c. 105.321 m
110.228 m
d. 4.89
d.
d.
S-25
The rectangular reinforced concrete beam with a width of 200 mm and an
effective depth of 500 mm is subjected to a service moment of 120 kN m.
The beam is reinforced with 4 25 mm diameter bars with n= 8.
95. The distance from the neutral axis from the top of the beam.
a. 461.452 mm
b. 342.123 mm
c.301.411 mm
d.
212.507 mm
96. The maximum stress in concrete is
a. 13.518 Mpa
b.15.221 Mpa
c. 21.412 Mpa
d.
22.881 Mpa
97.The maximum stress in steel is
a. 104.221 Mpa
b. 142.406 Mpa c. 177.231 Mpa
d. 190.241
Mpa
S -26
For the given set of system shown:
98. The magnitude of the resultant of the force system shown.

a. 77.14 N
b. 81.21 N
c. 84.22 N
d. 87.55 N
99. The angle that the resultant makes with the + x axis is
a. 44.220
b. 48.420
c. 52.220
d. 54.770
100. The moment of all forces with respect to 0.
a.204.17 Nm
b. 231.11 Nm
c. 369.69 Nm
d.
412.41 Nm
BONUS!----. The x intercept of the resultant force is
a. 4.221 m
b. 5.092 m
c. 6.063 m
d. 7.551 m
BONUS!--The y intercept of the resultant force is
a. -7.823 m
b. 7.829 m
c. 6.612 m
d.-6.421 m
S -26
A beam 100 mm by 200 mm has a simple span of 5 m. It carries a uniform
load of
5 kN/m.
92. The shear force 1 m from the left support is
a.
b. 7.5 kN
93. The shear stress at 30 mm from the top of the beam at a section 1
meter from the left support.
a.
b. 0.287 Mpa
94. The shear force carried by the section from the top to 30 mm below
the top at a section where shear is maximum.
a.
b.
c. 0.7593 kN
S -27
The force acting per meter length of the dam are shown.
78. The bearing pressure at A is

a. 163.2716Kpa
79. The bearing pressure at B is
a.
b. 108.025 kPa
80. The distance from B where the resultant applied forces intersect
base AB.
a. 2.883 m
81. Factor of safety against sliding if the coefficient of friction at the base
of the dam is 0.25.
a.
b. 1.386
S -28
To prevent excessive deflection of a 3 m long cantilever beam subjected
to a load of 2 Kn/M. Its free end is attached to a tension rod.
Beam properties are as follows.
A = 1900 mm2 I = 5.12 x 106 mm4
E = 200 Gpa
82. The maximum deflection before attaching the tension rod is
a. 19.78 mm
83. Maximum moment at the fixed end if the rod attached to the beam
has a tension of 2 Kn.
a.
b. 3 kN m
84. The maximum positive moment in the beam if the tension in the rod is
2.5kN.
a.
b. 1.5625 kN m
S - 29
The bridge truss shown on the figure carries a concentrated load of 20 kN
and a uniform load of 2 kN/m.
A unit load moves along the span AE .

85. The force at BG when the unit load is at B is
a. +0.3536 kN
86. The force at BG when the unit load is at C
a.
b. -0.707
87. The maximum value of the tensile force at BG due the given applied
loads is
a. 9.9kN
88. The maximum value of compressive force at BG due to the given

applied loads.
a.
b. 24.45 kN
S -30
The beam shown in the figure carries a triangular load as shown.
89. The reaction at A is

a. 17.333kN
90. The reaction at B is
a.
b. 38.667 kN
91. The location of the zero shear from A is
a. 1.6795 m
92. The maximum positive bending moment is
a.
b. 13.766 kN m
93. The location of the point of inflection from point A is
a. 3.615 m
94. The maximum negative moment is
a.
b. 40 kN m
S -31
A rectangular footing 2.5 meter wide along the y axis, 3 m long along the
x axis supports a circular pedestal 0.45 m in diameter. The horizontal force
acting at the top of the pedestal along the x axis of the footing is 144 kN.
The total axial load from the pedestal is 1200 kN. Thickness of the footing
is 0.7 m, height of backfill on top of the footing is 1.5 m, depth from the
top pedestal to the base of the footing is 2.5 m. Concrete unit weight = 24
kN/m3 Unit weight of soil = 17 Kn/m3
95. The maximum soil pressure is

a. 256 kPa
b. 276 kPa
c. 298 kPa
d. 321 kPa
96. The minimum soil pressure is
a. 61 kPa
b. 64 kPa
c. 67 kPa
d. 71 kPa
97. The required soil bearing capacity is
a. 201.1 kPa
b.244.1 kPa
c. 298.3 kPa
308.4 kPa
d.
S- 32
From the given frame shown using CANTILEVER method.
98. The location of the centroid from the leftmost column is

a. 6.667 m
b. 7.411 m
c. 8.761 m
d. 9.231 m
99. The axial load at AD is
a. 1.044 kN
b. 2.534 kN
c. 3.142 kN
d. 4.231 kN
100. The moment at D is
a. 4.41 kN
b. 5.22 kN m
c. 6.21 kN m
d. 7.06 kN
m

Design Exam (1) SHFHSDHSDH

Uploaded by

Copyright:

Available Formats

Design Exam (1) SHFHSDHSDH

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Design Exam (1) SHFHSDHSDH

Uploaded by

Copyright:

Available Formats

PREBOARD

DESIGN AND CONSTRUCTION

The vertical reaction at A

10. The flexular stress at A.

16. The vertical reaction at C is

19. The distance of the resultant load from the 10 Kn load is

27. The ordinate of the IL for max shear at midspan 4 m from A.

35. The vertical reaction at the column is

The tensile member shown is 50 mm by 75 mm and subjected to a load of

49. The force at cable AC is

A simply refinforced concrete beam reinforced for tension has a width of

55. The Fixed End Moment at D for span CD is

57. Using Three Moment Equations , the bending Moment Equations

CD if you consider span BCD is

64. The tensile stress in the body of the bolt.

The pin jointed assembly supports a billboard 2 m high x 4 n wide on

67. The resultant wind load is

73. The shear at D is

76. Compute the reactive moment at B.

P2 = 0.9 kN P3 = 0.45 kN = 300 = 450

80. The magnitude of the resultant of the 3 forces.

84. The minimum tension is

92. The initial acceleration of the block is

98. The magnitude of the resultant of the force system shown.

78. The bearing pressure at A is

A unit load moves along the span AE .

88. The maximum value of compressive force at BG due to the given

89. The reaction at A is

95. The maximum soil pressure is

98. The location of the centroid from the leftmost column is

You might also like