English

Warning Before Install

Power off the Network Camera Keep the Network Camera away
as soon as it is found smoking or from water. If the Network Camera
smelt unusual. is wet, power off immediately.

Contact your distributor when such Contact your distributor when such
cases happen. cases happen.

Do not place the Network Camera Refer to your user's manual for the
around the heat sources, such as operating temperature.
television or oven.

Power
/MIC

Activity

Powe
r/MIC

Activity

Keep the Network Camera away Do not place the Network Camera
from direct sunlight. in high humid environments.

Powe
r/MIC

Activity
Powe
r/MIC

Activity

EN - 1
Do not place the Network Camera Do not touch the Network Camera
on unsteady surfaces. when it's lightening.

Power
/MIC

Activity

Powe
r/MIC

Activity

Do not disassemble the Network Do not drop the Network Camera.

Camera.

ity
Activ

MIC
Power/

Powe
r/MIC

Activity

Do not insert any object into the Do not manually pan and tilt the
Network Camera, such as needles. Network Camera when the power is
on.

Powe
r/MIC

Activity
Powe
r/MIC

Activity

EN - 2
 English
1 Package Contents

PZ7111 / PZ7121/ Power adapter

PZ7112 / PZ7122

Pow
er/M
IC

Activity

Antenna Screws
(PZ7112 / PZ7122 only)

Quick installation guide / Software CD

Warranty card

A/V cable Ceiling mount brackets

EN - 3
2 Physical Description

Front panel

Lens

Built-in microphone

Status LED Power/MIC Activity

Back panel

Antenna
(PZ7112 / PZ7122 only)
Microphone in
Ethernet 10/100
RJ45 socket AV out
Power cord socket AV Indented reset button
e e

General I/O External/Internal

terminal block microphone switch

EN - 4
 English
3 Hardware Installation

Mounting the Network Camera

1. Attach ceiling mount bracket A to the Network Camera and secure it with two
small screws.
2. Drill three pilot holes into the ceiling; hammer the plastic anchors into the
holes.
3. Fasten ceiling mount bracket B to the ceiling with three screws.
4. Slide the Network Camera into ceiling mount bracket B.
5. Secure ceiling mount bracket A and B with a small screw.

4
3

1 5

A B

EN - 5
 4 Network Deployment

General Connection (without PoE)

1. If you have external devices such as sensors and alarms, make connections from gen-
eral I/O terminal block.
2. Connect the camera to a switch via a Ethernet cable.
3. Connect the supplied power cable from the camera to a power outlet.

3
1
1: Power
2: Digital output
e e
Audio
3: Digital input
4: Ground

POWER
COLLISION
1 2 3 4 5
LINK
RECEIVE
PARTITION 2

Ethernet switch

EN - 6
 English
Power over Ethernet (PoE)

When using a PoE-enabled switch

The camera is PoE-compliant, allowing transmission of power and data via single Ether-
net cable. See the following illustration to connect the camera to a PoE-enabled switch
via Ethernet cable.

Audio

e e

PoE switch

POWER LINK
COLLISION RECEIVE
1 2 PARTITION
3 4 5

When using a non-PoE switch

Use a PoE power injector (optional) to connect between the camera and a non-PoE
switch.

Audio

e e

PoE power injector

(optional)

POWER LINK
COLLISION RECEIVE
1 2 PARTITION
3 4 5

non-PoE switch

EN - 7
 5 Assigning IP Address

1. Install the "Installation Wizard 2" under the Software Utility directory from software CD.
2. The program will conduct analyses on your network environment. After your network is
analyzed, please click on the "Next" button to continue the program.

IW2

Installation
Wizard 2

3. The program will search the VIVOTEK Network Devices in the same LAN.
4. After searching, the main installer window will pop up. Click on the MAC that matches
the one labeled on the bottom of your device to connect the Internet Explorer to the
Network Camera.

Network Camera 172.16.7.13 PZ71X2

PZ7112
0002D10766AD
0002D10766AD
RoHS

EN - 8
 English
6 Ready to Use

1. Access to the Network Camera from the Internet.

2. Retrieve live video through web browsers or recording software.

For further setup, please refer to user's manual on the software CD.

EN - 9
 7 Configure the Wireless Connection (PZ7112 / PZ7122 only)

1. Check the SSID currently set on your wireless access point (AP).
2. Go to PZ7112 / PZ7122's Configuration > Advanced mode > Wireless.
3. Type in the SSID consistent with the setting on your AP.
4. Select the Wireless mode as "Infrastructure".
5. Click Save. The Network Camera starts to reboot.

6. Wait for the live image is reloaded to your browser. Then, unplug the power cable and
Ethernet cable from the Network Camera.
7. Replug the power cable to the camera. The Network Camera now operates in wireless
mode.

ble/Hub
ADSL/Ca

Audio

e e

AP
LINK
PZ7112 / PZ7122
POWER
COLLISION RECEIVE
1 2 3 4 PARTITION
5

Note

1. SSID, abbreviated from Service Set Identifier, is the name assigned to the wireless
network. The PZ7112 / PZ7122's factory SSID setting is set to "default".
2. Select "Ad-Hoc" wireless mode if you want the PZ7112 / PZ7122 to communicate
without using an AP or wireless router.

For further setup, please refer to user's manual on the software CD.

EN - 10
P/N:625006700G