This document provides instructions for wiring two lamps that are controlled by a single-pole switch. It describes connecting the power supply, switch, and lamps and includes a diagram. The procedure involves turning off power, connecting white neutral wires and black hot wires between the power supply, switch, and two lamps. Bare or green ground wires are connected together and to any metal boxes.
Copyright:
Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOCX, PDF, TXT or read online from Scribd
This document provides instructions for wiring two lamps that are controlled by a single-pole switch. It describes connecting the power supply, switch, and lamps and includes a diagram. The procedure involves turning off power, connecting white neutral wires and black hot wires between the power supply, switch, and two lamps. Bare or green ground wires are connected together and to any metal boxes.
This document provides instructions for wiring two lamps that are controlled by a single-pole switch. It describes connecting the power supply, switch, and lamps and includes a diagram. The procedure involves turning off power, connecting white neutral wires and black hot wires between the power supply, switch, and two lamps. Bare or green ground wires are connected together and to any metal boxes.
Copyright:
Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOCX, PDF, TXT or read online from Scribd
This document provides instructions for wiring two lamps that are controlled by a single-pole switch. It describes connecting the power supply, switch, and lamps and includes a diagram. The procedure involves turning off power, connecting white neutral wires and black hot wires between the power supply, switch, and two lamps. Bare or green ground wires are connected together and to any metal boxes.
Copyright:
Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOCX, PDF, TXT or read online from Scribd
Download as docx, pdf, or txt
You are on page 1/ 3
TITLE : ONE WAY SINGLE POLE SWITCH CONTROL
OBJECTIVE : To Learn function of one way switch to control two lamps.
Switch S1 controls Lamp 1 (L1) and Lamp 2 (L2)
To doing the wiring for 2 lamps that is controlled by a one way switch.
To know how to sketch the wiring and schematic diagrams
To find out and choose the suitable cable size and wiring clip to do the wiring
To know how to use the suitable devices to do the wiring work.
To find out,operate and joint the wiring component using the right steps.
To install protection devices for lamps circuit and power.
To doing the pole test for the wiring work that already done.
Equipment : three circular wood, two ceiling rose, one distribution fuse board, one way, Switch, two filament lamp, PVC single core, screw, wiring clip
Diagram : Procedure : 1. Go to the service panel and turn off power to the circuit you will be working on. If there is already a switch with one light installed, return to the switch and remove the cover. Check all wires for current with your voltage tester. If there is only one black wire connected to the switch, follow the instructions in step two. If there is more than one black wire connected to the switch, follow the instructions in step three.
2. The power supply connects to the first light: Connect the white wire from the power supply to the white wire from the light. Connect the black wire from the power supply to the white wire of the cable connected to the switch. Wrap a piece of black electrical tape around each end of this white wire to indicate that it is a hot wire rather than a neutral wire. Run your cable from the first light to the second light. Connect the black wire from the switch to the black wire from the first light and the black wire coming from the second light. Attach the white from the second light to the white from the power supply.
3. The power supply connects to the switch: Connect the black
wire from the power supply to the switch and the white wire from the power supply to the white wire of the cable connected to the first light. Connect the black wire from the first light to the switch. Run your cable from the first light to the second light and connect black to black and white to white.
4. Connect all bare or green wires together and to the boxes if
they are metal. Any green screws on the switch or lights should also be connected to the bare wires. Screw insulated connectors over all wire connections
Discussion : A single-pole switch is a one-blade, on-and-off switch that may
be installed singly or in multiples of two or more in the same metal box. In wiring a single-pole switch, a general rule is a neutral conductor (white wire) should not be switched or used as one leg in a switch loop. This rule is easily followed in conduit systems but does not apply to armored and non metallic sheathed cable
Conclusion : This would obviously be the 'ON' position. When the insulated lever is moved down to the 'OFF' position, it pushes the metal strip away to breaking the circuit and turning the light 'OFF'.This type of switch (having a lever which "flips" it on and off) is called a toggle switch.
