PIC-WEB development board

Users Manual

Rev.A, July 2008

Copyright(c) 2008, OLIMEX Ltd, All rights reserved
INTRODUCTION:
PIC-WEB is compact board with 65x60 mm size which is supported by
Microchip’s open source TCP-IP stack AN833. The board is designed
with PIC18F452 microcontroller and ENC28J60 Ethernet controller and
supports: SLIP, ARP, IP, ICMP, TCP, UDP, HTTP, DHCP, FTP. The
Microchip stack is written on modular and flexible basis and you can
enable or disable modules. The stack also supports dynamic web pages
which give you the possibility to control all PIC resources remotely via
FTP, HTTP, UDP, TCP etc. With this board you can implement web and
ftp server, send e-mails and almost everything what a big server can do.
The on board 1Mbit serial flash is available for data storage

BOARD FEATURES:
− PIC18F452 microcontroller, ENC28J60 Ethernet controller
− 1Mbit on board serial flash for web pages storage
− ICSP/ICD connector for programming with PIC-MCP, PIC-MCP-USB and
programming and debugging with PIC-ICD2 and PIC-ICD2-POCKET.
− Reset button
− User event button
− Analogue trimmer potentiometer
− Thermistor for temperature monitoring
− RS232 driver and connector
− Complete web server and TCP-IP stack support as per Microchip's open
source TCP-IP stack
− Power plug-in jack for +5VDC power supply
− Voltage regulator +3.3V and filtering capacitors
− Status LED
− Extension header to connect to other boards
− Dimensions 60x65 mm (2.36x2.55")

ELECTROSTATIC WARNING:
The PIC-WEB board is shipped in protective anti-static packaging. The
board must not be subject to high electrostatic potentials. General practice
for working with static sensitive devices should be applied when working
with this board.

BOARD USE REQUIREMENTS:

Cables: Depends on the used programming/debugging tool. It could be
1.8 meter USB A-B cable to connect PIC-MCP-USB, PIC-ICD2
or PIC-ICD2-POCKET to USB host on PC or RS232 cable in
case of PIC-MCP or other programming/debugging tools. You
will need a serial cable if not for programming,
than for configuring the board. You will also need a LAN cable.

Hardware: Programmer/Debugger – most of Olimex programmers are

applicable, for example PIC-MCP, PIC-MCP-USB, PIC-ICD2,
PIC-ICD2-POCKET or other compatible
programming/debugging tool.
 Software: PIC-WEB is tested with MPLAB IDE v.7.62 + MPLAB C18 C
compiler. It is possible that the stack might not function
properly if used with later versions of MPLAB IDE.
You will also need a terminal program configured at 19 200
bps, 8N1 and no flow control.

PROCESSOR FEATURES:
PIC-WEB board uses microcontroller PIC18F452 from Microchip with these
features:
- C compiler optimized architecture/instruction set
o Source code compatible with the PIC16C, PIC17C and PIC18C
instruction sets
- 32 Kbytes FLASH, 1536 bytes RAM and 256 bytes EEPROM on board
- Up to 10 MIPs operation:
o DC - 40 MHz osc./clock input
o 4 MHz - 10 MHz osc./clock input with PLL active
- 16-bit wide instructions, 8-bit wide data path
- Priority levels for interrupts
- 8 x 8 Single Cycle Hardware Multiplier
- High current sink/source 25 mA/25 mA
- Three external interrupt pins
- Timer0 module: 8-bit/16-bit timer/counter with 8-bit programmable
prescaler
- Timer1 module: 16-bit timer/counter
- Timer2 module: 8-bit timer/counter with 8-bit period register (time-base
for PWM)
- Timer3 module: 16-bit timer/counter
- Secondary oscillator clock option - Timer1/Timer3
- Two Capture/Compare/PWM (CCP) modules. CCP pins that can be
configured as:
o Capture input: capture is 16-bit, max. resolution 6.25 ns
(TCY/16)
o Compare is 16-bit, max. resolution 100 ns (TCY)
o PWM output: PWM resolution is 1- to 10-bit, Max. PWM freq. @:
8-bit resolution = 156 kHz and 10-bit resolution = 39 kHz
- Master Synchronous Serial Port (MSSP) module, Two modes of
operation:
o 3-wire SPI™ (supports all 4 SPI modes)
o I2C™ Master and Slave mode
- Addressable USART module:
o Supports RS-485 and RS-232
- Parallel Slave Port (PSP) module
- Compatible 10-bit Analog-to-Digital Converter module (A/D) with:
o Fast sampling rate
o Conversion available during SLEEP
o DNL = ±1 LSb, INL = ±1 LSb
- Programmable Low Voltage Detection (PLVD)
o Supports interrupt on-Low Voltage Detection
- Programmable Brown-out Reset (BOR)
- 100,000 erase/write cycle Enhanced FLASH program memory typical
- 1,000,000 erase/write cycle Data EEPROM memory
- FLASH/Data EEPROM Retention: > 40 years
- Self-reprogrammable under software control
- Power-on Reset (POR), Power-up Timer (PWRT) and Oscillator Start-up
Timer (OST)
- Watchdog Timer (WDT) with its own On-Chip RC Oscillator for reliable
operation
- Programmable code protection
- Power saving SLEEP mode
- Selectable oscillator options including:
o 4X Phase Lock Loop (of primary oscillator)
o Secondary Oscillator (32 kHz) clock input
- Single supply 5V In-Circuit Serial Programming™ (ICSP™) via two pins
- In-Circuit Debug (ICD) via two pins
- Low power, high speed FLASH/EEPROM technology
- Fully static design
- Wide operating voltage range (2.0V to 5.5V)
- Industrial and Extended temperature ranges
BLOCK DIAGRAM:
MEMORY MAP:
SCHEMATIC:
BOARD LAYOUT:

POWER SUPPLY CIRCUIT:

PIC-WEB can take power from two sources:

- PWR_JACK where 9-12 VDC (or 6-9 VAC) is applied by external power
source.
- EXT-20 pin VIN with the same DC voltage range.

The board power consumption is: about 130 mA with all peripherals and
MCU running at full speed.

RESET CIRCUIT:
PIC-WEB reset circuit is made with R12 (10k) pull-up, R15 (330R) serial
resistor and RST button.
On the schematic is made provision for external reset through EXT-16 pin.
Manual reset is possible by the RST button.

CLOCK CIRCUIT:
Quartz crystal 10 MHz is connected to PIC18F452 clock in (OSC1/CLKIN)
and clock out (OSC2/CLKOUT).
 32.768 KHz quartz crystal is connected to PIC18F452 T1OSO and T1OSI
pins for its internal Real Time Clock.

JUMPER DESCRIPTION:
There aren’t any jumpers.

INPUT/OUTPUT:

One User button with name BUTTON – connected to PIC18F452 pin 8

(PORTB.RB0/INT0);

Status green LED with name STAT connected to PIC18F452 pin3

(PORTD.RD5/PSP5).

Power supply red LED with name PWR – indicates that external powers
source is applied and board power supply is applied;

One trimmer AN_TR is connected to PIC18F452 pin 19 (PORTA.RA0/AN0).

EXTERNAL CONNECTORS DESCRIPTION:

ICSP:

Pin # Signal Name

1 RST

2 +5V

3 GND

4 PGD

5 PGC

6 PGM

PGD I/O Program Data. Serial data for programming.

PGC Input Program Clock. Clock used for transferring the serial data (output from
ICSP, input for the MCU).
PGM Input Program Enable (output from ICSP, input for the MCU).

RS232:

Pin # Signal Name

 1 NC

2 TXD

3 RXD

4 NC

5 GND

6 NC

7 RTS

8 CTS

9 NC

TXD OutputTransmit Data. This is the asynchronous serial data output (RS232) for the
shift register on the UART controller.
RXD Input Receive Data. This is the asynchronous serial data input (RS232) for the
shift register on the UART controller.
RTS Pin Request To Send. This is the RST pin on the board which is not connected
to the PIC18F452 MCU.
CTS Pin Clear To Send. This is the CTS pin on the board which is not connected to
the PIC18F452 MCU.

PWR_JACK:

Pin # Signal Name

1 Power Input

2 GND

The power input should be +9VDC/6VAC.

EXT:
 ATTENTION!!!: EXT-18 pin is not 3.3V but 5V!!!
Pin # Signal Name Pin # Signal Name

1 RA2/AN2/VREF– 2 RA3/AN3/VREF+

3 RA4/T0CKI 4 RA5/AN4/#SS/LVDIN

5 RE0/RD#/AN5 6 RE1/WR#/AN6

7 RE2/CS#/AN7 8 RC2/CCP1

9 RD0/PSP0 10 RD1/PSP1

11 RD2/PSP2 12 RD3/PSP3

13 RD4/PSP4 14 RD6/PSP6

15 RD7/PSP7 16 RST

17 +5V 18
+5V!!!
19 GND 20 VIN

LAN:

Pin # Signal Name Chip Side Pin # Signal Name Chip Side

1 TPOUT+ 5 Not Connected (NC)

2 TPOUT- 6 Not Connected (NC)

3 3.3V 7 TPIN+

4 Not Connected (NC) 8 TPIN-

LED Color Usage

Right Yellow Activity

 Left Green 100MBits/s (Half/Full duplex)

TPOUT- Output Differential signal output.

TPOUT+ Output Differential signal output.
TPIN- Input Differential signal input.
TPIN+ Input Differential signal input.

MECHANICAL DIMENSIONS:

All measures are in Inches.

AVAILABLE DEMO SOFTWARE:

You could find information about PIC-WEB board, Microchip TCP/IP stack
and how to change and configure the software in Understanding PIC WEB
boards on www.olimex.com/dev.
ORDER CODE:

PIC-WEB – assembled and tested (no kit, no soldering required)

How to order?
You can order to us directly or by any of our distributors.
Check our web www.olimex.com/dev for more info.

All boards produced by Olimex are RoHS compliant

Revision history:

REV.A - created July 2008

Disclaimer:
© 2008 Olimex Ltd. All rights reserved. Olimex®, logo and combinations thereof, are
registered trademarks of Olimex Ltd. Other terms and product names may be trademarks of
others.
The information in this document is provided in connection with Olimex products. No
license, express or implied or otherwise, to any intellectual property right is granted by this
document or in connection with the sale of Olimex products.
Neither the whole nor any part of the information contained in or the product described in
this document may be adapted or reproduced in any material from except with the prior
written permission of the copyright holder.
The product described in this document is subject to continuous development and
improvements. All particulars of the product and its use contained in this document are
given by OLIMEX in good faith. However all warranties implied or expressed including but
not limited to implied warranties of merchantability or fitness for purpose are excluded.
This document is intended only to assist the reader in the use of the product. OLIMEX Ltd.
shall not be liable for any loss or damage arising from the use of any information in this
document or any error or omission in such information or any incorrect use of the product.