Sony STR De725
Sony STR De725
Sony STR De725
SPECIFICATIONS
AUDIO POWER SPECIFICATIONS Inputs (Analog) PHONO:
POWER OUTPUT AND TOTAL HARMONIC DISTORTION: Sensitivity: 2.5 mV
With 8 ohm loads, both channels driven, from 20 - 20,000 Hz; rated Impedance: 50 kilohms
100 watts per channel minimum RMS power, with no more than S/Nb): 75 dB (A, 2.5 mVc))
0.09% total harmonic distortion from 250 milliwatts to rated output . CD, DVD/LD, TAPE, MD/DAT, TAPE/MD, TV/DBS,
VIDEO 1 and VIDEO 2 :
Amplifier section Sensitivity: 150 mV
POWER OUTPUT Impedance: 50 kilohms
Stereo mode (8 ohms 20 Hz –20 kHz, THD 0.09%) S/Nb): 82 dB (A, 150 mVc))
100 W + 100 W
Surround mode (8 ohms at 1 kHz, THD 0.8%) b)78’ IHF
Front: 100 W/ch c) Weighted network, input level
Centera): 100 W
Reara): 100 W/ch Inputs (Digital) DVD/LD:
Sensitivity: –
a) Depending on the sound field settings and the source, there may be no Impedance: –
sound output. S/N: 100 dB (A, 20 kHz LPF)
Outputs TAPE/MD, (REC OUT); VIDEO 1, 2
Dynamic power output (AUDIO OUT):
155 W + 155 W, 8 ohms Voltage: 150 mV
220 W + 220 W, 4 ohms Impedance: 10 kilohms
Harmonic distortion at rated output WOOFER:
Less than 0.09% (with sound field, tone, and bass Voltage: 2 V
booster bypassed) Impedance: 1 kilohms
Frequency response PHONES:
PHONO: RIAA Accepts low - and high-impedance headphones
equalization curve BASS BOOST +6 dB at 70 Hz
±0.5 dB
CD, TAPE, MD/DAT, TAPE/MD, DVD/LD, TV/DBS,
VIDEO 1 and VIDEO 2 :
10 Hz - 50 kHz +0.5/–2 dB (with sound field, tone, — Continued on next page —
and bass booster bypassed)
MICROFILM
Sampling Frequency Harmonic distortion
48 kHz 0.5% (50 mV/m, 400 kHz)
EQ BASS: Selectivity At 9 kHz: 35 dB
100 Hz ~ 1.0 kHz (21 steps) At 10 kHz: 40 dB
MID:
500 Hz ~ 5.0 kHz (21 steps) d)You can change the AM tuning scale to 9 kHz. After tuning in any AM
TREBLE: station, turn off the receiver. Hold down the TUNING + button and
1.0 kHz ~ 10 kHz (21 steps) press the 1/u button. All preset stations will be erased when you
Gain levels: change the tuning scale. To reset the scale to 10 kHz, repeat the
±10 dB, 1 dB step procedure.
—2—
SAFETY CHECK-OUT TABLE OF CONTENTS
After correcting the original service problem, perform the 1. GENERAL ······································································ 4
following safety checks before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs, screws, 2. TEST MODE ···························································· 6
and all other exposed metal parts for AC leakage. Check leakage as
described below. 3. DIAGRAMS
3-1. Circuit Boards Location ····················································· 7
LEAKAGE 3-2. Block Diagram — Main Section — ··································· 9
3-3. Block Diagram — Power Section — ······························· 11
The AC leakage from any exposed metal part to earth ground and 3-4. Printed Wiring Board — AMP Section — ······················· 13
from all exposed metal parts to any exposed metal part having a 3-5. Schematic Diagram — AMP Section — ·························· 15
return to chassis, must not exceed 0.5 mA (500 microampers). 3-6. Printed Wiring Board — Video Section — ······················ 17
Leakage current can be measured by any one of three methods. 3-7. Schematic Diagram — Video Section — ························· 19
3-8. Printed Wiring Board —AUDIO Section — ···················· 21
1. A commercial leakage tester, such as the Simpson 229 or RCA 3-9. Schematic Diagram — AUDIO Section — ······················ 23
WT-540A. Follow the manufacturers’ instructions to use these 3-10. Printed Wiring Board — Input Section — ······················· 25
instruments. 3-11. Schematic Diagram — Input Section — ·························· 27
3-12. Printed Wiring Board — Display Section — ··················· 29
2. A battery-operated AC milliammeter. The Data Precision 245 3-13. Schematic Diagram — Display Section — ······················ 31
digital multimeter is suitable for this job. 3-14. Printed Wiring Board — SPEAKER Section — ·············· 33
3-15. Schematic Diagram — SPEAKER Section — ················· 35
3. Measuring the voltage drop across a resistor by means of a 3-16. Printed Wiring Board — Power Section — ····················· 37
VOM or battery-operated AC voltmeter. The “limit” indication 3-17. Schematic Diagram — Power Section — ························ 39
is 0.75 V, so analog meters must have an accurate low-voltage 3-18. Printed Wiring Board
scale. The Simpson 250 and Sanwa SH-63Trd are examples of — DIGITAL (SIDE A) Section — ··································· 41
a passive VOM that is suitable. Nearly all battery operated 3-19. Printed Wiring Board
digital multimeters that have a 2V AC range are suitable. (See — DIGITAL (SIDE B) Section — ··································· 43
Fig. A) 3-20. Schematic Diagram — DIGITAL Section (1/3) — ·········· 45
3-21. Schematic Diagram — DIGITAL Section (2/3) — ·········· 47
To Exposed Metal 3-22. Schematic Diagram — DIGITAL Section (3/3) — ·········· 49
Parts on Set 3-23. IC Pin Function Description ············································ 51
3-24. IC Block Diagrams ··························································· 61
4. EXPLODED VIEWS
AC 4-1. Front Panel Section ·························································· 64
0.15µF 1.5kΩ voltmeter 4-2. Chassis Section ································································· 65
(0.75V)
5. ELECTRICAL PARTS LIST ··································· 66
Earth Ground
—3—
SECTION 1
GENERAL
LOCATION AND FUNCTION OF CONTROLS
[FRONT PANEL]
1 2 3 4 5 6 7 8 9 0 !¡
#§
#∞
#¢
#£ !™
#™
#¡
#º @• @§¿ @¡ @º !• !§
@ª @¶ @∞ @¢ @£ @™ !ª !¶ !∞ !¢ !£
—4—
[REAR PANEL]
1 2 3 4 5 6 7 8 9 0 !¡ !™ !£ !¢ !∞
@º !ª !• !¶ !§
—5—
SECTION 2
TEST MODE
FLUORESCENT INDICATOR TUBE TEST MODE SOUND FIELD CLEAR MODE
* All fluorescent segments are tested. When this test is activated, * The preset sound field is cleared when this mode is activated.
all segments turn on at the same time, then each segment turns on Use this mode before returning the product to clients upon
one after another. completion of repair.
* Procedure: * Procedure:
While depressing the SET UP and the SOUND FIELD MODE While depressing the SOUND FIELD ON/OFF button, press
buttons simultaneously, press the power 1/u button to turn on the power 1/u button to turn on the main power. The message
the main power. All segments turn on at the same time, then each SURR CLEAR! appears and initialization is performed.
segment turns on one after another.
AM CHANNEL STEP 9 kHz/10 kHz
SELECTION MODE
FACTORY SET MODE * Either the 9 kHz step or 10 kHz step can be selected for the AM
* All preset contents are reset to the default setting. channel step.
* Procedure: * Procedure:
While depressing the SET UP and the SOUND FIELD ON/OFF Set the FUNCTION to AM. Turn off the main power.
buttons simultaneously, press the power 1/u button to turn on While depressing the TUNING+ button or the PRESET TUNING
the main power. The message FACTORY SET appears and the + button, press the power 1/u button to turn on the main power.
present contents are reset to the default values. Either the message AM 9kHz STEP or AM 10kHz STEP appears.
Select the desired step.
—6—
STR-DE725
SECTION 3
DIAGRAMS
3-1. CIRCUIT BOARDS LOCATION THIS NOTE IS COMMON FOR PRINTED WIRING
BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this necessary note is printed in each
block.)
AC board For schematic diagrams. For printed wiring boards.
Note: Note:
REG board
• All capacitors are in µF unless otherwise noted. pF: µµF • X : parts extracted from the component side.
DISPLAY board AMPLIFIER board 50 WV or less are not indicated except for electrolytics • ® : Through hole.
SP board and tantalums. • b : Pattern from the side which enables seeing.
REAR AMP board
• All resistors are in Ω and 1/4 W or less unless otherwise
SP SW board specified.
• % : indicates tolerance.
• 2 : nonflammable resistor.
VIDEO board • 1 : fusible resistor.
• C : panel designation.
• Waveform
TUNER board The components identified by mark ! or dotted
line with mark ! are critical for safety.
Replace only with part number specified. 1 IC1201 (™ (XO)
• U : B+ Line.
• V : B– Line.
D.IN/OUT board 4.0Vp-p
H.P board • H : adjustment for repair.
• Voltages and waveforms are dc with respect to ground
DIGITAL board
under no-signal (detuned) conditions. 4MHz
No mark : FM
LED board AUDIO board
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production 2 IC1101 @¶ (X OUT)
SW board INPUT board tolerances.
• Waveforms are taken with a oscilloscope.
JOINT board
L.B board • Circled numbers refer to waveforms. 5.5Vp-p
VOLUME board • Signal path.
F : FM
BALANCE board J : CD 24.576MHz
c : DIGITAL
I : PHONO
3 IC1101 @ª (CLK OUT)
5.4Vp-p
12.288MHz
4 IC102 *™ (XO)
3.0Vp-p
4.0MHz
—7— —8—
STR-DE725
3-2. BLOCK DIAGRAM – MAIN SECTION –
AUDIO SELECT
IC301
TM301 SELECTOR
ANTENNA TUNER UNIT IC303
J305
FM AUDIO CODEC VOLUME
75Ω FM L OUT 10 3 4 RY301 IC405
TV/DBS INPUT L 1 4 IC1103 RV401 VOL CONT
IC304 IC1104 IC1104 IC1104
IC414
STEREO
AM AM R OUT 12 R CH 2 30 LIN+ L OUT1 27 IC408
TUNED
TMUTE
DVD/LD INPUT L 2 MUTE
DATA
14 IN OUT 15 L
CLK
Q302
DO
CE
1 29 LIN- BALANCE DATA
OUTPUT L 6 RV402 9 DATA
4 14 15 13 2 3 1 CLK
8 CLK
7 8 VIDEO2 J304 LAT
10 LAT
S DATA
S CLK
S LAT
6
STEREO
INPUT L 7 8
TUNED
TMUTE
5 VOL CONT
IC1105 IC407
DO
IC416
OUTPUT L 9 L OUT3 23 IC410
10 11 9 SDTO
J301 EQ AMP VIDEO1 3 IN OUT 2 C
IC302 9 MUTE
3 1 INPUT L 10 11
PHONO L 39 MCLK1 Q304
CONTROL CONTROL 4 BCLK IC1105 IC407
A
CD L 5 LRCK R OUT3 24 IC410
CLK
CE
CLK
DI
14 IN OUT 15 W
CE
DI
J302 AUDIO DSP MUTE
14 15 13
14 15 13 IC1401 Q354 DATA
INPUT L 9 DATA
CLK
113 BCK0 SOA 2 6 SDTI 1 8 CLK
S DATA
S DATA
MD/DAT LAT
S CLK
S CLK
S LAT
S LAT
115 LRCK SOB 3 7 SDTI 2 10 LAT
OUTPUT L 99 CLK1 SOC 4 8 SDTI 3
IC1106 IC406 VOL CONT
DOLBY
J303 IC415
DIGITAL AUDIO DECODER L OUT2 25 IC409
DIGITAL AUDIO
IC1301
CDTO
I/F RECEIVER
CCLK
INPUT L 14 IN OUT 15 SL
CDTI
IC1101 IC1108 IC1102
CS
PD
MUTE
TAPE AUDATA0 41 117 SIA DATA
22 SDATA1 Q303 9 DATA
OUTPUT L D OUT 35 AUDATA1 40 118 SIB 44 43 42 41 17 CLK
27 SDATA2 8 CLK
IC1305 AUDATA2 39 119 SIC LAT
10 LAT
CLK 29 44 MCLK
IC001
IC1006 IC1102
IR LINK
DVD/LD 15 BCK 34 43 SCK
DET 5 47 D IN
25 SCLK1 D0-7
SELECT 28 SCLK2 UP
SWITCH IC1102 SRAM
12 27 XO IC1402 M
IC1005 X1101 LRCK 36 42 RCLK A0-7
DOWN
3 A 11
A 24.576MHz
26 XI X1301 IC1305
IC1403 26 LRCLK1 B
B 49.152MHz 29 LRCLK2 74 XWE Q120
2 B 10 13 CLOCK 10
C DIVIDE 70 XOE LED
1 C 9 LED VOL
40 SWDT IC1305 IC1305 DRIVE
42 SCLK 30 CLK 16
ERROR 30
41 XLAT 20
. HD0
D0-7
23 HD7
11 RESET SRDT 38
25
XHDWR
RELAY
XHDRD
IC1304
XHDCS
XRST
AUDIO L A8-15 DRIVE
VIDEO 3
9 10 14 26
5 EMRD
VIDEO VIDEO SELECT SCDOUT 19
IC201 21 EXTMEM
Q1207
INTREQ 20
IC1202 IC1202
AC MUTE
SCD IN
SCCLK
RESET
J201 7 V3 IN PROTECTOR
Q1206
VCC 16 +5V
CS
MONITOR OUTPUT 1 M OUT IC202 RY HP
7 6 18 36 Q1201 RY FRONT A
INPUT 13 V1 IN VEE 8
-5V
3 REG 2 -15V
Q1203
MUTE RY FRONT B
C
VIDEO 1 CONT
DO
TMUTE
STEREO
TUNED
C
A
B
RY CENTER
IC1202
Q1204
Q1205
S CLK
S LAT
15 V1 OUT
S DATA
OUTPUT
D1201
Q1202
CLK
RY WOOFER
LAT
DATA
D0-7
RY REAR
J202
60 61 62 97 57 58 56 111 110109 76 78 77 2 75 67 14 16 15 17 20 19 18 25 32 35 21 22 24 36 23 37 6 5 4 3 7 108 85 49 50 48 84 79 106101102 103105104
ANALOG/DIG
FUN MUTE
INTREQ
XHDWR
ERROR
XHDCS
SCDOUT
HRDY
EV CLK
EV STB
SWDT
SCDIN
XHDRD
CDTO
SCLK
CDTI
RY DIRECT PASS
RESET
SCCLK
RESET
SRDT
HA0
AC MUTE
XRST
CCLK
SOD
CS
CS
PD
RY WOOFER
9 V2 IN
C
RY CENTER
PROTETOR
INPUT AD0 AD7
A
B
RY REAR
XLAT
RY HP
STEREO
EV DATA
RY FRONT B
TUNER MUTE
CLOCK
RY FRONT A
LATCH
AUTO STOP
DATA
DATA
VIDEO 2
OUTPUT 11 V2 OUT DISP DATA 52 U DATA
SW1 14 81 V-A DISP CLK 55 U CLOCK
DISP MR 51 U MREQ
J203
SW2 10 82 V-B
SREQ 53 U SREQ
TV/DBS INPUT 3 TV SYSTEM RESET 90 U REST
SW3 4 83 V-E CONTROL
DVD/LD INPUT 5 LD
IC1201 RY POWER 107 RY POWER D
STOP 64 STOP
SW4 6 80 V INH
SOTO 10 SOTO
SINO 9 SINO
MD2 87 MD2
16
XI XO MD0 89 MD0
93 92
X1201
4MHz
• RCH is omitted
• Signal Path
: FM
: PHONO
: CD
: DIGITAL
—9— — 10 —
STR-DE725
3-3. BLOCK DIAGRAM – POWER SECTION –
POWER AMP(L)
IC501 R CH J701
PHONES
+B 13 VCC
BOOSTER RY602
14 VCC +VE 2
Q506 RELAY
-B 15 VEE DRIVE
LIMITER Q601
Q504
L 6 IN NF 5
PROTECTOR
+B
Q801
RY HP
B RY FRONT A
SWITCH
Q618
+32V
+32V
REG
F802
FRONT B
-B
RY CENTER F803
SWITCH SWITCH INV SW D802-805
RY WOOFER
Q612,615 Q613,616 Q617
RY REAR
IC809 +24V
S501 8 +5V
1 3 F804
IMPEDANCE REG
SELECTOR 4
RY POWER -24V F805
STOP
IC801 D808
URESET
5V
USREQ D5V 3 1
D111-113 D100,108 REG
D109,110 D114,115 D116-118 D101 D104-106 D119,122
UMREQ IC802
UCLOCK +3.3V
D UDATA
D3.3V 3
REG
1
F2
IC803
SOTO
LED LED LED LED LED LED +3.3V
SINO D3.3V 3 1 F1
F901
DRIVE DRIVE DRIVE DRIVE DRIVE DRIVE REG
MD2
Q109,110 Q114,115 Q111-113 Q102 Q103,104 Q107,108 X101 RY901
MD0 Q118-116 Q106 Q119,122 RELAY
DRIVE
IC101 Q901
49 51 20 19 61 62 60 59 1 2 6 7 3 4 5 10 9 8 90 16 15 14 92 89 87 91 82 83
IC106 Q101 REMOTO
XI
XO
MD0
MD2
SINO
LED CD
UCLOCK
LED V1
LED V2
LED V3
UMREQ
USEQ
SOTO
LED EQ
LED ON/OFF
LED INDEX
LED TUNER
LED MUTE
LED SUR
LED DVD/LD
LED PHONO
LED BASS B
LED TV/DBS
SIRCS 26 CONTROL
UP 8 3 55 UP RECEIVER
MOTOR
DRIVE DELAY
B DOWN 7 2 56 DOWN URESET 58 +5.6V +B SW
Q902 JW925 CNJ901
MODE CONTROL RESET
LED VOL 88 LED VOL IC102 RESET 77 Q105 T902
POWER KEY
D901-904
ABUS A1 IN
ABUS OUT
3
FL CLEAR
AD KEY1
AD KEY2
AD KEY3
AD KEY4
AD KEY5
AD KEY6
FL CLK
FL DAT
FL LAT
POWER
SP B
SP A
STOP 47 8 CONT 5
16 IC901 CNP901
38 39 40 41 43 44 72 73 74 21 24 25 24 67 63
6 AC IN
CLK
CL
DIN
LS
MUTING POWER
LAT
I/O
BUFFER
DIN 29 3 DOUT
IC104 IC105
FL DRIVE FL DRIVE
F2 F1 J204
S-LINK
FL101
FLOURESCENT
INDICATOR TUBE
— 11 — — 12 —
STR-DE725
3-4. PRINTED WIRING BOARD — AMP SECTION — • See page 7 for Circuit Boards Location.
• Semiconductor Location 1 2 3 4 5 6 7 8 9 10 11 12 13
Ref. No. Location
D501 E-6 (Page 34) (Page 34) (Page 37) (Page 37) (Page 43)
D502 E-6
D503 E-6 A Q M O (Page 26) I P L N (Page 33)
D809
D556 B-4 5 1
D601 E-8
C B 1 3 1 3
−
D602 E-8 A
D603 E-8 R
D604 E-9 A
D608 C-11 E E
B E
D647 D-3
D648 E-4 E E
D801 C-8 D E
D802 D-10
D803 C-9 E E
2 1
D804 D-10
E E E E E E
D805 D-10 E E
D806 B-10
D807 D-8
11
D809 C-12 E 1 11
B C E B C E B C E 1-670-025- (12)
IC809 C-12
B C E B C E B C E B C E B C E B C E
Q504 E-6 Q506 Q505 Q507 Q606 Q605 Q607 Q556 Q555 Q557
Q505 E-6
Q506 E-5
Q507 F-7
Q508 E-7
F X
(Page 33)
Q509 B-4
Q510 B-4
Q511 B-4
Q546 B-11 H.P BOARD
1
Q547 D-12
Q548 D-12
JOINT BOARD 1
Q549 D-12 G (Page 25) J701
Q554 E-11 R PHONES
1-670-006-
3
11
Q555 E-11 1
Q556 E-10 (13)
Q557 E-12
Q558 E-12 11 11
Q559 C-4
Q560 B-4 1-670-027- (12)
H
Q561 B-4
Q596 B-11 11
Q601 B-11
Q604 E-9 16
Q605 E-8
Q606 E-8
Q607 E-9
Q608 E-9
Q612 E-4
Q613 D-4
Q615 E-3
Q616 D-3
Q617 D-3
Q618 D-3
Q801 D-8
— 13 — — 14 —
STR-DE725
3-5. SCHEMATIC DIAGRAM — AMP SECTION —
— 15 — — 16 —
STR-DE725
3-6. PRINTED WIRING BOARD — VIDEO SECTION — • See page 7 for Circuit Boards Location.
1 2 3 4 5 6 7 8 9
A VIDEO BOARD
TV/DBS DVD/LD VIDEO 2 VIDEO 1 MONITOR S-LINK
VIDEO IN VIDEO IN VIDEO OUT VIDEO IN VIDEO OUT VIDEO IN VIDEO OUT CTRL A1
11
1 8 3
C 1-670-003-
(13)
16 9
D
10 2
• Semiconductor
11 1 Location
Ref. No. Location
D201 C-2
D202 C-2
E 16
IC201 C-2
IC202 C-4
C
(Page 29)
— 17 — — 18 —
STR-DE725
3-7. SCHEMATIC DIAGRAM — VIDEO SECTION — • See pages 61 for IC Block Diagrams.
— 19 — — 20 —
STR-DE725
3-8. PRINTED WIRING BOARD — AUDIO SECTION — • See page 7 for Circuit Boards Location.
• Semiconductor
1 2 3 4 5 6 7 8 9 10 11 12
Location
Ref. No. Location
(Page 26) (Page 25)
IC303 G-8
A
IC408 D-6
E K
IC409 C-6
IC410 B-6 TUNER BOARD
VOLUME
BOARD
C382
1 5
8 1 11
B
1 10 1
S
8 1 (Page 43)
C D
(Page 26) 1
11
8 1
D
MASTER VOLUME
11
1-670-011- (13) 1-670-000-
R108
1 11
E 1 4
(13)
A (Page 25)
TM301
(Page 29)
F
F
AUDIO BOARD
BALANCE
11 16 30
G
1-670-015- (13)
BALANCE BOARD
15 1
I 1-670-001-
11
16 L R L R L R L R L R L R (13)
— 21 — — 22—
STR-DE725
3-9. SCHEMATIC DIAGRAM — AUDIO SECTION —
— 23 — — 24 —
STR-DE725
3-10. PRINTED WIRING BOARD — INPUT SECTION — • See page 7 for Circuit Boards Location.
• Semiconductor 1 2 3 4 5 6 7 8 9 10 11 12 13
Location
Ref. No. Location
D301 F-10 A
IC301 C-4 INPUT BOARD
IC302 D-4 (Page 14) (Page 34) (Page 22) (Page 14)
IC304 E-6
IC401 C-12 R H D I
IC402 B-12
IC403 D-12 B
IC404 E-4 1 8
IC405 E-12 1 13
IC406 D-12 1 6 E E 14
16 9 3 1
IC407 D-12
1 15
IC414 B-11
IC415 C-11 L 1 15 1 8
IC416 D-11 C IN 1 15
IC501 C-9 30
3
R 16
16 9 3 1
IC601 D-7 TAPE/MD
IC701 C-7 L 1
REC 1 1 8
OUT
Q301 F-11 3 1
R
Q302 E-11 1 15 16 9
Q303 E-11 D L
E E E 1 8
Q304 D-11 2 1
CD IN
Q352 E-11
R 1 4
Q353 D-10 10
1 3
Q354 D-11 L E
Q501 C-10 8 5
PHONO IN 1 8
Q503 C-10
R
E 1 8 E
3
5 1
1
1 8
1 E
E
1-670-026-
16
F
11
K F V G (12)
(Page 22) (Page 18) (Page 22) (Page 43)
E
(Page 21)
— 25 — — 26 —
STR-DE725
3-11. SCHEMATIC DIAGRAM — INPUT SECTION — • See page 61 for IC Block Diagrams.
— 27 — — 28 —
STR-DE725
3-12. PRINTED WIRING BOARD — DISPLAY SECTION — • See page 7 for Circuit Boards Location.
• Semiconductor 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Location
Ref. No. Location B (Page 43)
D100 H-2
A DISPLAY BOARD
D101 E-2
(Page 17)
D102 B-13 C192
D103 B-9 C 2 1 JW231
D104 C-12 MULTI
E CURSOR
D105 C-12
B CONTROL
C123
C124
E E
D106 C-12 1 11 E E
D108 C-3 2 10 E E
E E E
E E E E E E E E
D109 J-6 1 64
D110 J-7
D111 J-7 C191
D112 J-8 E
D113 J-9 C (SOUND FIELD)
(SURROUND)
D116 I-7
A 3 1
R122
1 4
D117 I-8 (BASS BOOST) 31
(INDEX)
1
D118 I-9
D119 D-3 D 80
30
RR21
RR22
D120 H-14 81 5
Q114 B-12 5
Q118 B-13 1 4 1 4 1 4
INPUT BASS
Q119 B-4 I MODE BOOST
CURSOR MODE
J DIRECT 1 2 3 4 5
TUNING
11
1-670-009- (13)
16
11
1-670-010- (13)
— 29 — — 30 —
STR-DE725
3-13. SCHEMATIC DIAGRAM — DISPLAY SECTION — • See page 8 for Waveform. • See page 51 for IC Pin Function Description. • See page 61 for IC Block Diagrams.
— 31 — — 32 —
STR-DE725
3-14. PRINTED WIRING BOARD — SPEAKER SECTION — • See page 7 for Circuit Boards Location.
• Semiconductor
Location 1 2 3 4 5 6 7 8 9 10
Ref. No. Location
D543 G-7 (Page 26) (Page 13)
D605 F-8
D606 F-9 A H M
D607 F-12 REAR AMP BOARD
D649 F-6
D701 B-7 B B
BC E C E BC E BC E C E BC E
D702 B-7
D703 B-7
D704 B-7 6 1
D705 G-6
D706 F-6 E
D749 E-5
D751 B-3 B E
D752 B-3 E
E
D753 B-3
3 1
D754 B-3
IC702 F-10
11
Q544 F-7 1-670-002-
Q609 E-9 (13)
Q610
Q611
F-9
F-9
C
Q645 E-8 N
Q704 B-7
(Page 14)
Q705 B-7
Q706 B-7
Q707 B-6
Q708 B-8
Q710 F-6
Q745 F-6
Q747 E-9 D
Q748 E-9 TM701
Q754
Q755
B-3
A-3
SP BOARD REAR CENTER WIRELESS REAR
IMPEDANCE SELECTOR
SPEAKER
Q756 A-4 4-8
WOOFER
Q757 A-2
Q758 B-2
E E
3
E
E 1
F E
E E
1-670-035-
E
11
E E
(13)
5 1
4 1 6 1
G 16
X V U Q
(Page 14) (Page 25) (Page 43) (Page 13)
— 33 — — 34 —
STR-DE725
3-15. SCHEMATIC DIAGRAM — SPEAKER SECTION —
— 35 — — 36 —
STR-DE725
3-16. PRINTED WIRING BOARD — POWER SECTION — • See page 7 for Circuit Boards Location.
• Semiconductor 1 2 3 4 5 6 7 8 9 10 11 12 13
Location
Ref. No. Location
CNJ901
D808 C-3 AC OUTLET
D901 D-4
A
D902 D-4
D903 D-4 REG BOARD
D904 C-4 AC BOARD
D905 C-4
D906 C-4
D907 G-8 4 1
B
IC801 E-2
IC802 F-3
IC803 G-3
IC901 F-4
Q901 D-4
Q902 G-4 C
JW903
E
D
1 3
EB901
5 8
F 1 3
4 1
4 1
T902
E
G
EB902
1 3
6 1
11
11
16 1-670-005- (13)
1-669-998- (13)
H AC
T901
POWER
T (Page 43)
IN
TRANSFORMER
1
3
I
4
(Page 14) O 6
1
J 2
(Page 14) P 3
— 37 — — 38 —
STR-DE725
3-17. SCHEMATIC DIAGRAM — POWER SECTION — • See page 61 for IC Block Diagrams.
— 39 — — 40 —
STR-DE725
3-18. PRINTED WIRING BOARD — DIGITAL (SIDE A) SECTION — • See page 7 for Circuit Boards Location.
• Semiconductor 1 2 3 4 5 6 7 8 9 10 11 12 13 14
Location
Ref. No. Location
D1201 H-4 A D. IN/OUT BOARD
D1205 G-8
D1206 H-4 DIGITAL BOARD (SIDE A) (SIDE A)
IC1005 D-13
IC1006 C-13
IC1007 B-13
IC1101 F-10
B 23 22
8 7
IC1102 E-11 14 1 17 7
60 31
IC1103 D-2 61 30 18 6
IC1104 F-4
IC1105 F-2
IC1106 F-3 1
44
IC1108 E-10 C
IC1109 E-11 44 1
IC1154 F-5 28 40
90 1
IC1201 F-7 91 120 29 39
IC1202 B-6
IC1301 C-8 9 8
11 1
R1312
14 8 14 8
IC1302 C-10 12 44
IC1303 D-9 D 1 7
1 7 7 1
IC1304 D-10
IC1305 D-7 16 1
IC1401 C-5 22 34 7 1
23 33 8 14
IC1402 C-3
R1160
C1117
IC1403 D-8
E E E E
E 8 14
Q1201 H-3 IC1109
Q1202 H-3
Q1203 H-3
Q1204 E-9 30 11
Q1205 E-9 31 36 25
Q1206 E-9 IC1154 120
5 4 5 4 5 4 5 4 5 4 37 24
Q1207 E-8 F
Q1208 H-4 8 1 8 1 8 1 8 1 8 1
48 13
1-670-029-
60 91 1 12
G 61 90
11
(13)
E E
H Q1208
E A A
E
D1206
K
11
16 1-670-028- (13)
— 41 — — 42 —
STR-DE725
3-19. PRINTED WIRING BOARD — DIGITAL (SIDE B) SECTION — • See page 7 for Circuit Boards Location.
1 2 3 4 5 6 7 8 9 10 11 12
• Semiconductor
D. IN/OUT BOARD Location
A DIGITAL BOARD (SIDE B) (SIDE B) Ref. No. Location
D1202 F-4
D1203 F-3
C1309
D1204 G-2
JW11
IC1001 E-11
IC1501 D-7
B
C
JW13
R1331
R1332
X1301 C1409
C1502
IC1501 C1501
C1313 3
C1115
C1113
C1308
C1302
1 JW12
D CNS13
C1173 C1123 C1174 C1124 C1175 C1125 C1176 C1126 1
IC1001 1
6
R1285
DVD LD
IN
E C1201 3
R1282
1-670-029-
11
C1172 C1170 C1122 C1120 C1138 C1136 C1134 C1132 C1130 C1128
FB1101 (13)
C1105
F
C1102
C1139 C1140
FB1102
6 1
CN12
CNS10
CNP14 20 2 CNP10
C1218
G C1141 6 1 21 1 1 11 R1319
C1143
CNS11
CNP11 CNP12 28 2
1 3 1 7 29 1
11
1-670-028- (13)
H 16
U T L B G S
(Page 34) (Page 37) (Page 14) (Page 29) (Page 26) (Page 22)
— 43 — — 44 —
STR-DE725
3-20. SCHEMATIC DIAGRAM — DIGITAL SECTION (1/3)— • See page 41,43 for Printed Wiring Board. • See page 51 for IC Pin Functions. • See page 61 for IC Block Diagrams.
— 45 — — 46 —
STR-DE725
3-21. SCHEMATIC DIAGRAM — DIGITAL SECTION (2/3)— • See page 41,43 for Printed Wiring Board. • See page 51 for IC Pin Functions. • See page 8 for Waveforms.
— 47 — — 48 —
STR-DE725
3-22. SCHEMATIC DIAGRAM — DIGITAL SECTION (3/3)— • See page 41,43 for Printed Wiring Board. • See page 51 for IC Pin Functions. • See page 8 for Waveforms. • See page 61 for IC Block Diagrams.
— 49 — — 50 —
3-23. IC PIN FUNCTION DESCRIPTION
IC1103 AK4526 (DIGITAL BOARD)
— 51 —
Pin No. Pin Name I/O Description
31 RIN– I Rch analog negative input pin
32 RIN+ I Rch analog positive input pin
33 VREFL I Negative voltage reference input pin, AVSS (Connected to Ground)
Common voltage output pin, AVDD/2
34 VCOM O
Large external capacitor is used to reduce power-supply noise
35 VREFH I Positive voltage reference input pin, AVDD
36 A. 5V — Analog power supply pin
37 A. GND — Analog ground pin
38 XTI I X’tal input pin (Not used)
39 MCLKI I External master clock input pin if XTS = “L”
Parallel/serial select pin
40 S/P I
“L”: serial control mode, “H”: parallel control mode (Connected to Ground)
41 CS I Chip select pin in serial mode
42 CCLK I Control data clock pin in serial mode
43 CDTI I Control data input in serial mode
44 CDTO O Control data output pin in serial mode
If pins TEST, ICKS0, ICKS1, PD, S/P, DFS, DEM0, DEM1, CAD0, CAD1, S/M, MCLK, SDOS are not driven, then TEST, ICKS0, ICKS1, CAD0, CAD1,
must be tied to either AVSS or AVDD. PD, S/P, DFS, DEM0, DEM1, S/M, MCLK, SDOS must be tied to either DVSS or DVDD.
— 52 —
IC1401 CXD2712R (DIGITAL BOARD)
Pin No. Pin Name I/O Description
1 VSS3 — Ground
2–5 SOA – SOD O Serial data output
6, 7 ECJ0, ECJ1 I Conditional jump input terminal (7pin Connected to Ground)
8 — NC No connection
9 XHDWR I HCIF data write
10 XHDRD I HCIF data read
11 VSS4 — Ground
12 VDD2 — +3.3V
13 HRDY O HCIF ready signal Open drain
14 XHDCS I HCIF chip select
15 HA0 I HCIF address input
16 – 20 HD0 – HD4 I/O HCIF data input/output
21 VSS5 — Ground
22 VDD3 — +3.3V
23 – 25 HD5 – HD7 I/O HCIF data input/output
26 XRST I Reset input “L”: active
27 – 30 FGP0 – FGP3 O Test data output
31 VSS6 — Ground
32 – 40 ED0 – ED8 I/O External RAM data input/output
41 VSS7 — Ground
42 VDD4 — +3.3V
43 – 49 ED9 – ED15 I/O External RAM data input/output
50 TSTD I Test data input “L” = normal “H” = test (Connected to Ground)
51 VSS8 — Ground
52 VDD5 — +3.3V
53 – 60 ED16 – ED23 I/O External RAM data input/output
61 VSS9 — Ground
62 – 69 ED24 – ED31 I/O External RAM data input/output
70 XOE O External RAM output enable
71 VSS10 — Ground
72 VDD6 — +3.3V
73 CAS O External RAM column address strobe (Not used)
74 XWE O External RAM write enable (Not used)
75 RAS O External RAM raw address strobe
76 – 80 EA0 – EA4 I/O External RAM address output/test data input
81 VSS11 — Ground
82 VDD7 — +3.3V
83 –89 EA5 – EA11 I/O External RAM address output/test data input
90 EA12 O External RAM address output
— 53 —
Pin No. Pin Name I/O Description
91 VSS0 — Ground
92 – 94 EA13 – EA15 O External RAM address output
95 EA16 O Not used
96 TSTA I Test data input “L” = normal “H” = test (Connecting to Ground)
97 PLDIVF I PLL input frequency select “L” = 256Fs “H” = 128Fs (Connecting to Ground)
98 PLDIVB O PLL output frequency select “L” = 768Fs “H” = 1024Fs (Connecting to Ground)
99 CLKI I Master clock input
100 CLKO O Master clock output (Not used)
101 VSS1 — Ground
102 VDD0 — +3.3V
103 AVSS — Ground for PLL cell
104 AVDD — VDD for PLL cell
105 PLLCK I/O PLL output/test clock input
106 XPLLEN I PLL cell oscillation enable “L” oscillation enable “H” oscillation stop (Connecting to Ground)
107 TST I Test data input “L” = normal “H” = test (Connecting to Ground)
108 LRCT I Frequency counter input (Connecting to Ground)
109 LROUT O LRCK0 divider output
110 BKOUT O BCK0 divider output
111 VSS2 — Ground
112 VDD1 — +3.3V
113 BCK0 I BCK input
114 BCK1 I BCK input
115 LRCK0 I LRCK input
116 LRCK1 I LRCK input
117 – 120 SIA – SID I Serial data input
— 54 —
IC1101 CAD8495AQ (DIGITAL BOARD)
Pin No. Pin Name I/O Description
1 DOUT/V O EIAJ data and parity flag output terminal (Not used)
2 EMPHA O Emphasis monitor output terminal (“H” = ON)
3 RC1 I Input terminal for RC generator/oscillator
4 RC2 O Output terminal for RC generator/oscillator
5 CCB/SUB I Microprocessor I/F select input terminal (CCB: H, @SUB@: L) (Connecting to Ground)
6 D. GND — Digital Ground
7 CLKMD O Clock output select terminal ( “L” = 256fs, “H” = 128fs) (Connecting to Ground)
8 CLK I Clock input select terminal ( “H” = 512fs, “L” = 384fs)
9 TEST1 I Test terminal (normally ground)
10 TEST2 I Test terminal (normally ground)
11 RESET I Reset input terminal
12 D. VDD — Digital power supply
13 NC — No connect
14 A. VDD — Analog power supply
15 R I Input terminal for VCO generator band adjustment
16 A. GND — Analog Ground
17 VCO IN I Input terminal for VCO self running frequency set
18 VCO O External LPF for PLL is connected to this terminal
19 D. VDD — Digital power supply
20 SBSY O CD subcode I/F and block sync output terminal (Not used)
21 PW O CD subcode I/F and data output terminal (Not used)
22 SFSY O CD subcode I/F and frame sync output terminal (Not used)
23 SBCK I CD subcode I/F and shift clock input terminal for data reading (Not used)
24 D. GND — Digital Ground
25 D. VDD — Digital power supply
26 XIN I Crystal oscillator input terminal
27 XOUT O Crystal oscillator output terminal
28 CLK OUT1 O VCO and crystal oscillator clock output terminal (Not used)
29 CLK OUT2 O 256fs or 128fs clock output terminal (Select CLKMD terminal)
30 ERROR O Error mute output terminal
31 D. GND — Digital Ground
32 SUB1 O Sampling frequency monitor output terminal
33 SUB2 O Sampling frequency monitor output terminal
34 BCLK O Bit clock output terminal
35 DATA OUT O Audio data output terminal
36 LRCK O L, R clock output terminal (L-ch: “H”, R-ch: “L”)
37 LD/DQSY O Microprocessor I/F and subcode Q data sync output terminal (Not used)
38 SRDT O Microprocessor I/F. When CCB/SUB is “L”, data output terminal (3-state output)
39 DO O Microprocessor I/F. When CCB/SUB is “H”, data output terminal (high level open drain output) (Not used)
40 DI/SWDT I Microprocessor I/F. Data input terminal
41 CE/XLAT I Microprocessor I/F. Chip enable/latch input terminal
42 CL/SCLK I Microprocessor I/F. Clock input terminal
43 D. VDD — Digital power supply
44 DIN1 I Amplifier integrate data input terminal (Connecting to Ground)
45 DIN2 I Amplifier integrate data input terminal (Connecting to Ground)
46 DIN3 I Amplifier integrate data input terminal (Connecting to Ground)
47 DIN4 I Amplifier integrate data input terminal
48 D. GND — Digital Ground
— 55 —
IC1201 MB90574PFV-G-161-BND (DIGITAL BOARD)
— 56 —
Pin No. Pin Name I/O Description
51 DISPMR I Display master request (Connected to MB90553 U.MREQ)
52 DISPDATA I Display data (Connected to MB90553 U.DATA)
53 SLV DTA/REQ O Slave data/request (Connected to MB90553 U.SREQ)
54 VCC — Power supply +5 V
55 DISP CLK I Display clock (Connected to MB90553 U.CLOCK)
56 LAT O To tuner TM301 latch
57 DATA O To tuner TM301 data
58 CLK O To tuner TM301 clock
59 — — Not used (Connected to Ground)
60 DATA IN I PLL data input
61 AUSTOP I Auto stop input
62 STEREO I Stereo input
63 VSS — Ground (Connected to Ground)
64 STOP I AC power check
65 CCB/SUB I Not used (Connected to Ground)
66 EMPHA I Not used (Connected to Ground)
67 ERROR O Error output to CXD8495AQ
68 SUB 1 I Not used (Connected to Ground)
69 SUB 2 I Not used (Connected to Ground)
70 — — Not used (Connected to Ground)
71 — — Not used (Connected to Ground)
72 U/CED I U or CED (STR only)
73 — — Not used (Not connected, open)
74 — — Not used (Not connected, open)
75 SRDT I To CXD8495AQ C-bit
76 SWDT O To CXD8495AQ data
77 XLAT O To CXD8495AQ latch
78 SCLK O To CXD8495AQ clock
79 PROTEC I Protector input
80 VIDEO-INH O Video output inhibit
81 VIDEO-A O To NJM2296 video select A
82 VIDEO-B O To NJM2296 video select B
83 VIDEO-E O To NJM2296 video select E
84 ACMUTE O IC muting
85 FUNMUTE O Function muting
86 HSTX — Hardware standby (Connected to power supply +5 V)
87 MD 2 — MD2 (To MB90553 MD2)
88 MD 1 — MD1 (Connect to power supply)
89 MD 0 — MD0 (To MB90553 MD0)
90 RESET I Reset (Connected to MB90553 U.RESET)
91 VSS — Ground (Connected to Ground)
92 X0 — External ceramic filter 4 MHz is connected to this terminal
93 X1 — External ceramic filter 4 MHz is connected to this terminal
94 VCC — Power supply +5 V
95 P 00 I Flash memory rewrite (Connected to Ground)
96 P 01 I Flash memory rewrite (Connected to Ground)
97 TUNER MUT O Tuner muting
98 SURR MUT O Surround muting (Connected to Ground)
99 7E/8E I Not used (Connected to Ground)
100 — — Not used (Connected to Ground)
— 57 —
Pin No. Pin Name I/O Description
101 RY-FRONT/A O Front speaker A relay
102 RY-FRONT/B O Front speaker B relay
103 RY-CENTER O Center speaker relay
104 RY-REAR O Rear speaker relay
105 WOOFER-RY O Sub Woofer relay
106 RY-HP O Head phone relay
107 RY-POWER O Power relay
108 RY-DIR-PASS O Direct pass relay
109 DIG-IN 2 I Digital input select 2 (74HC151)
110 DIG-IN 1 I Digital input select 1 (74HC151)
111 DIG-IN 0 I Digital input select 0 (74HC151)
112 TEST 0 — Test port 0 (Not connected, open)
113 TEST 1 — Test port 1 (Not connected, open)
114 TEST 2 — Test port 2 (Not connected, open)
115 — — Not used (Connected to Ground)
116 — — Not used (Connected to Ground)
117 — — Not used (Connected to Ground)
118 — — Not used (Connected to Ground)
119 VSS — Ground (Connected to Ground)
120 — — Not used (Connected to Ground)
— 58 —
IC102 MB90553PF-G-131-BND (DISPLAY BOARD)
Pin No. Pin Name I/O Description
1 LED V1 O VIDEO 1 VISUAL display data output to LED
2 LED V2 O VIDEO 2 AUDIO display data output to LED
3 LED V3 O VIDEO 3 VISUAL display data output to LED
4 LED-DVD/LD O DVD/LD AUDIO display data output to LED
5 LED-TV/DBS O DVD/LD VISUAL display data output to LED
6 LED-TAPE O TV/DBS AUDIO display data output to LED
7 LED-MD/DAT O TV/DBS VISUAL display data output to LED
8 LED-CD O TAPE display data output to LED
9 LED-TUNER O MD/DAT display data output to LED
10 LED-PHONO O CD display data output to LED
11 VSS — Ground (Connected to Ground)
12 — — Not used. (Connected to Ground)
13 — — Not used. (Connected to Ground)
14 LED SUR O CURSOR MODE SURROUND display data output to LED
15 LED EQ O CURSOR MODE EQUIPMENT display data output to LED
16 LED INDEX O CURSOR MODE INDEX display data output to LED
17 — — Not used. (Connected to Ground)
18 — — Not used. (Connected to Ground)
19 SOT0 O UART data output to rewrite flash memory
20 SIN0 I UART data intput to rewrite flash memory
21 FL CLK O Clock output to flourescent display tube
22 FL DATA O Data output to flourescent display tube
23 VCC — Power supply +5 V
24 FL LAT O Fluorescent latch
25 FL CLEAR O Fluorescent clear
26 SIRCS IN I SIRCS input
27 C — External power regulator capacitor 0.1µ is connected to this terminal.
28 — — Not used (Connected to Ground)
29 — — Not used (Connected to Ground)
30 — — Not used (Connected to Ground)
31 — — Not used (Connected to Ground)
32 — — Not used (Connected to Ground)
33 — — Not used (Connected to Ground)
34 AVCC — Analog power supply +5 V
35 AVRH — AVRH (Connected to power supply +5 V)
36 AVRL — SVRL (Connected to Ground)
37 AVSS — Ground (Connected to Ground)
38 AD KEY IN 1 I Key input 1
39 AD KEY IN 2 I Key input 2
40 AD KEY IN 3 I Key input 3
41 AD KEY IN 4 I Key input 4
42 VSS — Ground (Connected to Ground)
43 AD KEY IN 5 I Key input 5
44 AD KEY IN 6 I Key input 6
45 AD VERSION I Version input
46 AD MODEL I Model input
47 STOP I Stop input
48 — — Not used (Connected to Ground)
49 MD 0 I MD 0 (To MD0 of MB90574)
50 MD 1 I MD 1 (Connected to power supply +5 V)
— 59 —
Pin No. Pin Name I/O Description
51 MD 2 I MD 2 (To MD2 of MB90574)
52 HSTX I Hardware STANDBY input
53 RDS CLOCK I RDS clock input
54 RDS DATA I RDS data input
55 VOL UP O Volume up data output
56 VOL DOWN O Volume down data output
57 — — Not used (Connected to Ground)
58 U-RESET O Reset output (Connected to MB90574 RESET)
59 U-SREQ I Slave request and data input (Connected to MB90574 SLV DATA/REQ)
60 U-MREQ O Master request output (Connected to MB90574 DISPMR)
61 U-DATA O Master data output (Connected to MB90574 DISP DATA)
62 U-CLOCK O Master clock output (Connected to MB90574 DISPCLK)
63 AUBUS-IN I Audio bus input
64 — — Not used (Connected to Ground)
65 — — Not used (Connected to Ground)
66 — — Not used (Connected to Ground)
67 AUBUS-OUT O Audio bus output
68 — — Not used (Connected to Ground)
69 FUNCTION-UP I Function encoder up input
70 FUNCTION-DW I Function encoder down input
71 — — Not used (Connected to Ground)
72 SP-A I Speaker A selector switch input
73 SP-B I Speaker B selector switch input
74 POW-KEY IN I Power key input
75 — — Not used (Connected to Ground)
76 — — Not used (Connected to Ground)
77 RESET I Reset (Display MCU)
78 — — Not used (Connected to Ground)
79 — — Not used (Connected to Ground)
80 — — Not used (Connected to Ground)
81 VSS — Ground (Connected to Ground)
82 X0 — External ceramic filter 4 MHz is connected to this terminal
83 X1 — External ceramic filter 4 MHz is connected to this terminal
84 VCC — Power supply +5 V
85 — — Not used. (Connected to Ground)
86 — — Not used. (Connected to Ground)
87 LED BASS. B O BASS. B display data output to LED
88 LED VOL O VOLUME display data output to LED
LED SOUND
89 O SOUND FIELD display data output to LED
FIELD
90 LED MUTE O MUTE display data output to LED
LED EQ ON/
91 O EQ ON/OFF display data output to LED
OFF
LED DOLBY
92 O DOLBY/DIGITAL display data output to LED
DIGITAL
93 MBUS-V1 I V1 input from MBUS
94 MBUS-V 2 I V2 input from MBUS
95 MBUS-TV I TV input from MBUS
96 MBUS-STATUS I STATUS input from MBUS
97 — — Not used. (Connected to Ground)
98 LAT O Learning microprocessor latch output
99 — — Not used. (Connected to Ground)
100 — — Not used. (Connected to Ground)
— 60 —
3-24. IC BLOCK DIAGRAMS
EXTMEM,
SDATAN2
SDATAN1
CMPCLK,
STCCLK2
CMPDAT,
SCDOUT,
SCLKN1,
IC1301 CS4923 (DIGITAL BOARD)
RCV958,
LRCKN1
SCLKN2
INTREQ
ABOOT,
SCDIO,
GPIO8
GPIO9
PSEL,
VDD3
VSS3
CS
28 27 26 25 24 23 22 21 20 19 18
CMPREQ,LRCKN2 29
CLK IN 30
COMPRESSED
CLKSEL 31 DIGITAL
DATA INPUT
PLL AUDIO
FILTD 32 INTERFACE
CLOCK INPUT
FILTS 33 SP DIF
MANAGER INTERFACE
VDDA 34 RECEIVER
VSSA 35
17 DATA0,EMAD0,GPIO0
RAM FRAMER SHIFTER 16 DATA1,EMAD1,GPIO1
RESET 36 INPUT BUFFER INPUT BUFFER CONTROLLER 15 DATA2,EMAD2,GPIO2
14 DATA3,EMAD3,GPIO3
PARALLEL
DD 37 13 VSS2
or
DC 38 SERIAL 12 VDD2
HOST 11 DATA4,EMAD4,GPIO4
INTERFACE 10 DATA5,EMAD5,GPIO5
ROM RAM
PROGRAM MEMORY PROGRAM MEMORY 24-Bit 9 DATA6,EMAD6,GPIO6
STC DSP
ROM RAM 8 DATA7,EMAD7,GPIO7
PROCESSING
DATA MEMORY DATA MEMORY 7 A0,SCCLK
RAM
OUTPUT BUFFER
OUTPUT
FORMATTER
39 40 41 42 43 44 1 2 3 4 5 6
AUDATA2
AUDATA1
AUDATA0
LRCLK
SCLK
MCLK
VDD1
VSS1
XMT958
WR,
DS,
EMWR,
GPIO10
RD,
R/W,
EMOE,
GPIO11
A1,
SCDIN
IC201 NJM2296D (VIDEO BOARD) IC1403 TC74VHC393FT(EL) (DIGITAL BOARD)
14 13 12 11 10 9 8
VCC
S6 S7 QA QB QC QD
CLEAR A
S1 S2
S4
CLEAR A
S5
S3 QA QB QC QD
GND
1 2 3 4 5 6 7
V-
1 2 3 4 5 6 7 8
Vout1 SW5 Vin5 SW3 Vin4 SW4 Vin3
IC1005 TC74HC151AF (EL) (D. IN/OUT BOARD) IC1108 MC74HC00AF (DIGITAL BOARD)
OUT3
OUT4
VDD
IN3
IN3
IN4
IN4
D3 1 16 VCC
14 13 12 11 10 9 8
D2 2 D2 D3 D4 15 D4
D1 3 D1 D5 14 D5
D0 4 D0 D6 13 D6
Y 5 Y D7 12 D7
XY 6 W A 11 A
OE 7 S C B 10 B
1 2 3 4 5 6 7
IN1
IN1
OUT1
IN2
IN2
OUT2
GND
GND 8 9 C
— 61 —
IC901 NJM2103D (REG BOARD)
CR 1 8 RESET
– +
OUTC 3 6 VSB/SESIN
GND 4 5 V+
Q
R S + – + –
CLK OUT2
CLK OUT1
ERROR
D GND
X OUT
SUB 2
SUB 1
D VDD
LRCK
BCLK
X IN
36 35 34 33 32 31 30 29 28 27 26 25
SRDT 38 23 SBCK
CD SUB-CODE
MICRO COMPUTER
MUTING
DETECTION
D0 39 22 SFSY
OUTPUT
INTERFACE
DI/SWDT 40 21 PW
ERROR LOCK
DETECTION
CE/XLAT 41 20 SBSY
CL/SCLK 42 19 D VDD
D VDD 43 18 VCO
PLL CIRCUIT
DIN1 44 17 V IN
MULTI PLEXER
DIN3 46 15 R
DIN4 47 14 A VDD
DGND 48 13 N.C.
TEST
1 2 3 4 5 6 7 8 9 10 11 12
DOUT/V
EMPHA
RC1
RC2
CCB/SUB
D GND
CLKMD
CLK
TEST1
TEST2
X MODE
D VDD
— 62 —
IC301 LC7822 (INPUT BOARD)
1 30
IN 2 29 IN
3 28
OUT 4 27 OUT
5 26
IN 6 25 IN
7 24
OUT 8 23 OUT
9 22
IN IN
10 21
OUT 11 20 OUT
LEVEL SHIFT
VEE 12 19 VDD
CE 13 LATCH 18 RESET
CONTROL
DI 14 17 S
SHIFT RESISTOR
CL 15 16 VSS
BIAS CIRCUIT
PROTECTOR
PRE PRE
REG DRIVE DRIVE
DRIVE DRIVE
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
MUTE
+ VOUT1
– VOUT1
COMP1
MF1
IN1
GND
IN2
NF2
COMP2
– VOUT2
+ VOUT2
VCC1
VCC2
VEE
VSS 1 16 VDD
OUT 2 15 OUT
L-CH R-CH
L-ch IN 3 DATA DATA 14 IN R-ch
LATCH LATCH
CIRCUIT CIRCUIT
NC 4 13 NC
A-GND 5 12 A-GND
CS1 6 11 CS2
SHIFT REGISTER (13bit)
LEVEL LEVEL
GND 7 SHIFT SHIFT 10 STB
CIRCUIT CIRCUIT
STROBE GENERATOR CIRCUIT
CK 8 9 DATA
— 63 —
SECTION 4
EXPLODED VIEWS
NOTE:
• -XX, -X mean standardized parts, so they may • The mechanical parts with no reference number
The components identified by mark ! or
have some differences from the original one. in the exploded views are not supplied.
dotted line with mark ! are critical for safety.
• Items marked “*” are not stocked since they • Hardware (# mark) list and accessories and Replace only with part number specified.
are seldom required for routine service. Some packing materials are given in the last of this
delay should be anticipated when ordering these parts list.
items.
4-1. FRONT PANEL SECTION
rA : L.B board
rB : BALANCE board
11
11
10
11
a
8
(including r A)
#1
9
#1
7 #1
5 #1
6
12
#1 a
4
SO 13
NY
rA
16 not supplied
15 #1
3
14
(including r B)
#1
rB #1
2 1
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
1 4-957-383-01 KNOB (F14) * 9 1-670-007-11 LED BOARD
2 X-4949-627-1 KNOB (VOL) ASSY * 10 4-982-682-01 CASE (414532)
3 4-998-717-01 KNOB (BAL) 11 4-210-291-01 SCREW (CASE 3 TP2)
4 4-996-698-01 EMBLEM, SONY 12 1-773-161-11 WIRE (FLAT TYPE) (21 CORE)
5 X-4949-745-1 PANEL ASSY, FRONT 13 1-769-959-11 WIRE (FLAT TYPE) (11 CORE)
— 64 —
4-2. CHASSIS SECTION
55 73
not supplied
a #1 72
#1
56 59 #1
#1 not supplied
#1 #1
#2 T901 #1
57 #1 #1
#2 not supplied
77
e #1 #1
#1
#1 #1 60 #1
b 53
54 #1
#1 e 58
a 67
not supplied not supplied 61 #1
#1
TM301
#1 b 63
76
66
not supplied #1 c 65
d d
52
#1
#1 #1
54 68
not supplied #1
71 c
#1
#1
70 #1
69
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
* 52 1-670-006-11 H.P BOARD 66 1-773-285-11 WIRE (FLAT TYPE) (29 CORE)
* 53 4-924-098-31 HOLDER, PC BOARD * 67 1-670-000-11 TUNER BOARD
54 4-985-642-01 CUSHION * 68 1-670-027-11 JOINT BOARD
* 55 1-669-998-11 AC BOARD * 69 A-4414-126-A DIGITAL BOARD, COMPLETE
* 56 A-4414-109-A REG BOARD, COMPLETE 70 4-977-358-11 CUSHION
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
* 1-669-998-11 AC BOARD C573 1-162-286-31 CERAMIC 220PF 10% 50V
******** C574 1-126-964-11 ELECT 10uF 20% 50V
C575 1-136-157-00 FILM 0.022uF 5% 50V
1-533-217-31 HOLDER, FUSE C576 1-136-153-00 FILM 0.01uF 5% 50V
C590 1-126-935-11 ELECT 470uF 20% 6.3V
< JACK >
C598 1-126-965-11 ELECT 22uF 20% 50V
! CNJ901 1-540-060-11 OUTLET, AC (POLAR) C620 1-104-664-11 ELECT 47uF 20% 16V
C621 1-107-597-11 CERAMIC 22PF 10% 500V
< CONNECTOR > C622 1-107-597-11 CERAMIC 22PF 10% 500V
C623 1-162-286-31 CERAMIC 220PF 10% 50V
CNP915 1-691-766-11 PLUG (MICRO CONNECTOR) 4P
CNV901 1-564-321-00 PIN, CONNECTOR 2P C625 1-136-157-00 FILM 0.022uF 5% 50V
* CNV902 1-565-792-11 PIN, CONNECTOR 2P C801 1-104-664-11 ELECT 47uF 20% 25V
C803 1-109-932-11 ELECT (BLOCK) 10000uF 20% 71V
< DIODE > C804 1-109-932-11 ELECT (BLOCK) 10000uF 20% 71V
C805 1-130-781-00 FILM 0.22uF 10% 100V
D907 8-719-911-19 DIODE 1SS119
C806 1-130-781-00 FILM 0.22uF 10% 100V
< TERMINAL > C807 1-126-967-11 ELECT 47uF 20% 50V
C808 1-126-967-11 ELECT 47uF 20% 50V
* EB902 1-537-738-21 TERMINAL, EARTH C811 1-126-953-11 ELECT 2200uF 20% 35V
C812 1-126-952-11 ELECT 1000uF 20% 35V
< FUSE >
C813 1-104-664-11 ELECT 47uF 20% 16V
! F901 1-533-311-11 FUSE,GLASS CYNDRICAL(DIA.5)8A CC48 1-136-153-00 FILM 0.01uF 5% 50V
CC49 1-136-153-00 FILM 0.01uF 5% 50V
< RESISTOR > CC98 1-136-153-00 FILM 0.01uF 5% 50V
CC99 1-136-153-00 FILM 0.01uF 5% 50V
! R901 1-202-725-00 SOLID 3.3M 10% 1/2W
< CONNECTOR >
< RELAY >
CNP751 1-779-978-11 PIN, CONNECTOR 3P
! RY901 1-515-999-11 RELAY, POWER * CNP801 1-564-243-11 PIN, CONNECTOR 6P
* CNP802 1-564-104-00 PIN, CONNECTOR (B3P-VH) 3P
< TRANSFORMER > CNP805 1-784-923-11 PIN, CONNECTOR 7P
CNP806 1-691-765-11 PLUG (MICRO CONNECTOR) 3P
! T902 1-450-361-11 TRANSFORMER, POWER
************************************************************ CNS651 1-784-806-11 HOUSING, CONNECTOR(PC BOARD)13P
R587 1-249-425-11 CARBON 4.7K 5% 1/4W F CC63 1-162-282-31 CERAMIC 100PF 10% 50V
! R588 1-249-407-11 CARBON 150 5% 1/4W F
! R607 1-216-456-00 METAL OXIDE 820 5% 2W F < CONNECTOR >
R621 1-249-422-11 CARBON 2.7K 5% 1/4W F
R622 1-247-881-00 CARBON 120K 5% 1/4W CNS351 1-784-729-11 CONNECTOR, FFC 7P
R628 1-249-419-11 CARBON 1.5K 5% 1/4W F J304 1-784-920-11 JACK, PIN 6P (VIDEO1IN/OUT,VIDEO2IN/OUT)
R632 1-249-437-11 CARBON 47K 5% 1/4W J305 1-784-920-11 JACK, PIN 6P (VIDEO2T,DVD,DVD/LD,TV/DBS)
! R633 1-249-393-11 CARBON 10 5% 1/4W F
! R640 1-215-886-11 METAL OXIDE 100 5% 2W F < RESISTOR >
R641 1-249-441-11 CARBON 100K 5% 1/4W
R315 1-249-417-11 CARBON 1K 5% 1/4W F
! R642 1-215-888-00 METAL OXIDE 220 5% 2W F R316 1-249-417-11 CARBON 1K 5% 1/4W F
R643 1-249-441-11 CARBON 100K 5% 1/4W R317 1-249-417-11 CARBON 1K 5% 1/4W F
! R644 1-216-456-00 METAL OXIDE 820 5% 2W F R318 1-249-417-11 CARBON 1K 5% 1/4W F
R645 1-249-441-11 CARBON 100K 5% 1/4W R319 1-249-417-11 CARBON 1K 5% 1/4W F
R650 1-249-425-11 CARBON 4.7K 5% 1/4W F
R320 1-249-417-11 CARBON 1K 5% 1/4W F
R657 1-249-429-11 CARBON 10K 5% 1/4W R365 1-249-417-11 CARBON 1K 5% 1/4W F
! R658 1-249-393-11 CARBON 10 5% 1/4W F R366 1-249-417-11 CARBON 1K 5% 1/4W F
R672 1-249-433-11 CARBON 22K 5% 1/4W R367 1-249-417-11 CARBON 1K 5% 1/4W F
R739 1-215-868-00 METAL OXIDE 680 5% 1W F R368 1-249-417-11 CARBON 1K 5% 1/4W F
R789 1-215-868-00 METAL OXIDE 680 5% 1W F
R369 1-249-417-11 CARBON 1K 5% 1/4W F
R801 1-247-843-11 CARBON 3.3K 5% 1/4W R370 1-249-417-11 CARBON 1K 5% 1/4W F
! R802 1-249-401-11 CARBON 47 5% 1/4W F R394 1-249-397-11 CARBON 22 5% 1/4W F
! RR48 1-249-393-11 CARBON 10 5% 1/4W F R395 1-249-397-11 CARBON 22 5% 1/4W F
! RR49 1-249-393-11 CARBON 10 5% 1/4W F R398 1-249-417-11 CARBON 1K 5% 1/4W F
! RR98 1-249-393-11 CARBON 10 5% 1/4W F
R399 1-249-425-11 CARBON 4.7K 5% 1/4W F
! RR99 1-249-393-11 CARBON 10 5% 1/4W F ************************************************************
* A-4414-126-A DIGITAL BOARD, COMPLETE C1206 1-163-275-11 CERAMIC CHIP 0.001uF 5% 50V
*********************** C1207 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C1208 1-165-319-11 CERAMIC CHIP 0.1uF 50V
< CAPACITOR > C1209 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C1210 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C1101 1-163-275-11 CERAMIC CHIP 0.001uF 5% 50V
C1102 1-126-022-11 ELECT 47uF 20% 16V C1211 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C1103 1-165-319-11 CERAMIC CHIP 0.1uF 50V C1212 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C1104 1-165-319-11 CERAMIC CHIP 0.1uF 50V C1213 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C1105 1-126-022-11 ELECT 47uF 20% 16V C1214 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C1215 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C1106 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C1107 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V C1216 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C1108 1-165-319-11 CERAMIC CHIP 0.1uF 50V C1217 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C1109 1-163-243-11 CERAMIC CHIP 47PF 5% 50V C1218 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C1110 1-163-243-11 CERAMIC CHIP 47PF 5% 50V C1301 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C1302 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C1111 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C1112 1-165-319-11 CERAMIC CHIP 0.1uF 50V C1303 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C1113 1-126-059-11 ELECT 10uF 20% 50V C1304 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C1114 1-165-319-11 CERAMIC CHIP 0.1uF 50V C1305 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C1115 1-126-059-11 ELECT 10uF 20% 50V C1306 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C1308 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C1116 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C1117 1-163-251-11 CERAMIC CHIP 100PF 5% 50V C1309 1-126-916-11 ELECT 1000uF 20% 6.3V
C1118 1-165-319-11 CERAMIC CHIP 0.1uF 50V C1310 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C1119 1-165-319-11 CERAMIC CHIP 0.1uF 50V C1311 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C1120 1-126-059-11 ELECT 10uF 20% 50V C1312 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C1313 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C1121 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C1122 1-126-233-11 ELECT 22uF 20% 50V C1401 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C1123 1-106-347-00 MYLAR 1500PF 5% 200V C1402 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C1124 1-126-233-11 ELECT 22uF 20% 50V C1403 1-163-275-11 CERAMIC CHIP 0.001uF 5% 50V
C1125 1-126-233-11 ELECT 22uF 20% 50V C1404 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C1405 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C1126 1-126-233-11 ELECT 22uF 20% 50V
C1127 1-163-251-11 CERAMIC CHIP 100PF 5% 50V C1406 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C1128 1-126-233-11 ELECT 22uF 20% 50V C1407 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C1129 1-163-251-11 CERAMIC CHIP 100PF 5% 50V C1408 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C1130 1-126-233-11 ELECT 22uF 20% 50V C1409 1-124-443-00 ELECT 100uF 20% 10V
C1410 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C1131 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C1132 1-126-233-11 ELECT 22uF 20% 50V C1411 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C1133 1-163-251-11 CERAMIC CHIP 100PF 5% 50V C1412 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C1134 1-126-233-11 ELECT 22uF 20% 50V C1413 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C1135 1-163-251-11 CERAMIC CHIP 100PF 5% 50V C1501 1-126-012-11 ELECT 470uF 20% 16V
C1502 1-126-022-11 ELECT 47uF 20% 16V
C1136 1-126-233-11 ELECT 22uF 20% 50V
C1137 1-163-251-11 CERAMIC CHIP 100PF 5% 50V < CONNECTOR >
C1138 1-126-233-11 ELECT 22uF 20% 50V
C1139 1-126-022-11 ELECT 47uF 20% 16V CNP10 1-784-926-11 PIN, CONNECTOR 11P
C1140 1-126-022-11 ELECT 47uF 20% 16V CNP11 1-779-977-11 PIN, CONNECTOR 6P
CNP12 1-784-923-11 PIN, CONNECTOR 7P
C1141 1-165-319-11 CERAMIC CHIP 0.1uF 50V CNP14 1-779-978-11 PIN, CONNECTOR 3P
C1142 1-165-319-11 CERAMIC CHIP 0.1uF 50V CNS10 1-784-782-11 CONNECTOR, FFC 21P
C1143 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C1170 1-126-059-11 ELECT 10uF 20% 50V CNS11 1-784-790-11 CONNECTOR, FFC 29P
C1171 1-165-319-11 CERAMIC CHIP 0.1uF 50V
— 69 —
DIGITAL
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
< DIODE > < RESISTOR >
D1101 8-719-016-74 DIODE 1SS352 R1101 1-216-025-91 RES, CHIP 100 5% 1/10W
D1201 8-719-016-74 DIODE 1SS352 R1102 1-216-025-91 RES, CHIP 100 5% 1/10W
D1202 8-719-801-78 DIODE 1SS184 R1103 1-216-025-91 RES, CHIP 100 5% 1/10W
D1203 8-719-801-78 DIODE 1SS184 R1104 1-216-085-00 METAL CHIP 33K 5% 1/10W
D1204 8-719-016-74 DIODE 1SS352 R1105 1-216-082-00 RES, CHIP 24K 5% 1/10W
D1205 8-719-016-74 DIODE 1SS352 R1106 1-216-066-00 METAL CHIP 5.1K 5% 1/10W
D1206 8-719-801-78 DIODE 1SS184 R1107 1-216-066-00 METAL CHIP 5.1K 5% 1/10W
R1108 1-216-029-00 METAL CHIP 150 5% 1/10W
< TERMINAL > R1109 1-216-104-00 METAL CHIP 200K 5% 1/10W
R1110 1-216-025-91 RES, CHIP 100 5% 1/10W
* EB1001 1-537-738-21 TERMINAL, EARTH
R1111 1-216-089-91 RES, CHIP 47K 5% 1/10W
< FERRITE BEAD > R1112 1-216-025-91 RES, CHIP 100 5% 1/10W
R1113 1-216-025-91 RES, CHIP 100 5% 1/10W
FB1101 1-410-397-21 FERRITE BEAD INDUCTOR R1114 1-216-025-91 RES, CHIP 100 5% 1/10W
FB1102 1-410-397-21 FERRITE BEAD INDUCTOR R1115 1-216-097-91 RES, CHIP 100K 5% 1/10W
< JUMPER RESISTOR > R1136 1-216-089-91 RES, CHIP 47K 5% 1/10W
R1137 1-216-089-91 RES, CHIP 47K 5% 1/10W
JW1 1-216-295-91 SHORT 0 R1138 1-216-089-91 RES, CHIP 47K 5% 1/10W
JW2 1-216-295-91 SHORT 0 R1139 1-216-049-91 RES, CHIP 1K 5% 1/10W
JW3 1-216-295-91 SHORT 0 R1140 1-216-089-91 RES, CHIP 47K 5% 1/10W
JW11 1-216-295-91 SHORT 0
JW12 1-216-295-91 SHORT 0 R1141 1-216-089-91 RES, CHIP 47K 5% 1/10W
R1142 1-216-089-91 RES, CHIP 47K 5% 1/10W
JW13 1-216-295-91 SHORT 0 R1143 1-216-049-91 RES, CHIP 1K 5% 1/10W
R1144 1-216-089-91 RES, CHIP 47K 5% 1/10W
< TRANSISTOR > R1145 1-216-089-91 RES, CHIP 47K 5% 1/10W
Q1201 8-729-216-22 TRANSISTOR 2SA1162-G R1146 1-216-089-91 RES, CHIP 47K 5% 1/10W
Q1202 8-729-027-43 TRANSISTOR DTC114EKA-T146 R1147 1-216-049-91 RES, CHIP 1K 5% 1/10W
Q1203 8-729-230-49 TRANSISTOR 2SC2712-YG R1148 1-216-089-91 RES, CHIP 47K 5% 1/10W
Q1204 8-729-230-49 TRANSISTOR 2SC2712-YG R1149 1-216-089-91 RES, CHIP 47K 5% 1/10W
Q1205 8-729-230-49 TRANSISTOR 2SC2712-YG R1150 1-216-089-91 RES, CHIP 47K 5% 1/10W
— 70 —
DIGITAL
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
R1156 1-216-049-91 RES, CHIP 1K 5% 1/10W R1239 1-216-073-00 METAL CHIP 10K 5% 1/10W
R1157 1-216-295-91 SHORT 0 R1240 1-216-073-00 METAL CHIP 10K 5% 1/10W
R1158 1-216-025-91 RES, CHIP 100 5% 1/10W R1241 1-216-073-00 METAL CHIP 10K 5% 1/10W
R1159 1-216-025-91 RES, CHIP 100 5% 1/10W R1242 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R1160 1-216-089-91 RES, CHIP 47K 5% 1/10W R1243 1-216-025-91 RES, CHIP 100 5% 1/10W
R1161 1-216-089-91 RES, CHIP 47K 5% 1/10W R1244 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R1162 1-216-089-91 RES, CHIP 47K 5% 1/10W R1245 1-216-041-00 METAL CHIP 470 5% 1/10W
R1163 1-216-089-91 RES, CHIP 47K 5% 1/10W R1246 1-216-025-91 RES, CHIP 100 5% 1/10W
R1164 1-216-089-91 RES, CHIP 47K 5% 1/10W R1247 1-216-025-91 RES, CHIP 100 5% 1/10W
R1165 1-216-089-91 RES, CHIP 47K 5% 1/10W R1248 1-216-065-91 RES, CHIP 4.7K 5% 1/10W
R1166 1-216-089-91 RES, CHIP 47K 5% 1/10W R1249 1-216-073-00 METAL CHIP 10K 5% 1/10W
R1170 1-216-065-91 RES, CHIP 4.7K 5% 1/10W R1250 1-216-065-91 RES, CHIP 4.7K 5% 1/10W
R1171 1-216-065-91 RES, CHIP 4.7K 5% 1/10W R1251 1-216-073-00 METAL CHIP 10K 5% 1/10W
R1172 1-216-073-00 METAL CHIP 10K 5% 1/10W R1252 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R1173 1-216-065-91 RES, CHIP 4.7K 5% 1/10W R1253 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R1174 1-216-037-00 METAL CHIP 330 5% 1/10W R1254 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R1175 1-216-073-00 METAL CHIP 10K 5% 1/10W R1255 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R1176 1-216-037-00 METAL CHIP 330 5% 1/10W R1256 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R1177 1-216-073-00 METAL CHIP 10K 5% 1/10W R1257 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R1178 1-216-049-91 RES, CHIP 1K 5% 1/10W R1258 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R1179 1-216-049-91 RES, CHIP 1K 5% 1/10W R1259 1-216-073-00 METAL CHIP 10K 5% 1/10W
R1180 1-216-049-91 RES, CHIP 1K 5% 1/10W R1260 1-216-065-91 RES, CHIP 4.7K 5% 1/10W
R1201 1-216-097-91 RES, CHIP 100K 5% 1/10W R1261 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R1202 1-216-049-91 RES, CHIP 1K 5% 1/10W R1262 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R1203 1-216-049-91 RES, CHIP 1K 5% 1/10W R1263 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R1204 1-216-049-91 RES, CHIP 1K 5% 1/10W R1264 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R1205 1-216-049-91 RES, CHIP 1K 5% 1/10W R1265 1-216-049-91 RES, CHIP 1K 5% 1/10W
R1206 1-216-049-91 RES, CHIP 1K 5% 1/10W R1266 1-216-049-91 RES, CHIP 1K 5% 1/10W
R1207 1-216-049-91 RES, CHIP 1K 5% 1/10W R1267 1-216-073-00 METAL CHIP 10K 5% 1/10W
R1208 1-216-049-91 RES, CHIP 1K 5% 1/10W R1268 1-216-073-00 METAL CHIP 10K 5% 1/10W
R1209 1-216-049-91 RES, CHIP 1K 5% 1/10W R1269 1-216-065-91 RES, CHIP 4.7K 5% 1/10W
R1210 1-216-049-91 RES, CHIP 1K 5% 1/10W R1270 1-216-025-91 RES, CHIP 100 5% 1/10W
R1211 1-216-049-91 RES, CHIP 1K 5% 1/10W R1271 1-216-073-00 METAL CHIP 10K 5% 1/10W
R1212 1-216-049-91 RES, CHIP 1K 5% 1/10W R1272 1-216-049-91 RES, CHIP 1K 5% 1/10W
R1213 1-216-049-91 RES, CHIP 1K 5% 1/10W R1273 1-216-073-00 METAL CHIP 10K 5% 1/10W
R1214 1-216-049-91 RES, CHIP 1K 5% 1/10W R1274 1-216-073-00 METAL CHIP 10K 5% 1/10W
R1215 1-216-025-91 RES, CHIP 100 5% 1/10W R1275 1-216-025-91 RES, CHIP 100 5% 1/10W
R1216 1-216-025-91 RES, CHIP 100 5% 1/10W R1276 1-216-025-91 RES, CHIP 100 5% 1/10W
R1217 1-216-025-91 RES, CHIP 100 5% 1/10W R1277 1-216-025-91 RES, CHIP 100 5% 1/10W
R1218 1-216-049-91 RES, CHIP 1K 5% 1/10W R1278 1-216-025-91 RES, CHIP 100 5% 1/10W
R1219 1-216-049-91 RES, CHIP 1K 5% 1/10W R1279 1-216-025-91 RES, CHIP 100 5% 1/10W
R1220 1-216-049-91 RES, CHIP 1K 5% 1/10W R1280 1-216-025-91 RES, CHIP 100 5% 1/10W
R1221 1-216-049-91 RES, CHIP 1K 5% 1/10W R1282 1-216-295-91 SHORT 0
R1222 1-216-049-91 RES, CHIP 1K 5% 1/10W R1283 1-216-295-91 SHORT 0
R1223 1-216-104-00 METAL CHIP 200K 5% 1/10W R1285 1-216-073-00 METAL CHIP 10K 5% 1/10W
R1229 1-216-097-91 RES, CHIP 100K 5% 1/10W R1304 1-216-025-91 RES, CHIP 100 5% 1/10W
R1230 1-216-097-91 RES, CHIP 100K 5% 1/10W R1305 1-216-025-91 RES, CHIP 100 5% 1/10W
R1231 1-216-049-91 RES, CHIP 1K 5% 1/10W R1306 1-216-041-00 METAL CHIP 470 5% 1/10W
R1232 1-216-049-91 RES, CHIP 1K 5% 1/10W R1307 1-216-065-91 RES, CHIP 4.7K 5% 1/10W
R1233 1-216-049-91 RES, CHIP 1K 5% 1/10W R1308 1-216-049-91 RES, CHIP 1K 5% 1/10W
R1234 1-216-049-91 RES, CHIP 1K 5% 1/10W R1309 1-216-025-91 RES, CHIP 100 5% 1/10W
R1235 1-216-049-91 RES, CHIP 1K 5% 1/10W R1310 1-216-081-00 METAL CHIP 22K 5% 1/10W
R1236 1-216-049-91 RES, CHIP 1K 5% 1/10W R1311 1-216-065-91 RES, CHIP 4.7K 5% 1/10W
R1237 1-216-049-91 RES, CHIP 1K 5% 1/10W R1312 1-216-025-91 RES, CHIP 100 5% 1/10W
R1238 1-216-049-91 RES, CHIP 1K 5% 1/10W R1313 1-216-065-91 RES, CHIP 4.7K 5% 1/10W
— 71 —
DIGITAL DISPLAY
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
R1314 1-216-295-91 SHORT 0 C121 1-104-664-11 ELECT 47uF 20% 16V
R1315 1-216-295-91 SHORT 0 C122 1-164-159-11 CERAMIC 0.1uF 50V
R1316 1-216-295-91 SHORT 0 C123 1-164-159-11 CERAMIC 0.1uF 50V
R1317 1-216-295-91 SHORT 0 C124 1-162-294-31 CERAMIC 0.001uF 10% 50V
R1318 1-216-295-91 SHORT 0 C183 1-126-964-11 ELECT 10uF 20% 50V
! R1319 1-215-884-11 METAL OXIDE 47 5% 2W F C184 1-126-964-11 ELECT 10uF 20% 50V
R1320 1-216-061-00 METAL CHIP 3.3K 5% 1/10W C191 1-164-159-11 CERAMIC 0.1uF 50V
R1321 1-216-061-00 METAL CHIP 3.3K 5% 1/10W C192 1-107-818-11 CAPACITOR 1F 5.5V
R1322 1-216-061-00 METAL CHIP 3.3K 5% 1/10W CC20 1-164-159-11 CERAMIC 0.1uF 50V
R1323 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
< CONNECTOR >
R1324 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
R1325 1-216-061-00 METAL CHIP 3.3K 5% 1/10W CNP106 1-784-919-11 CONNECTOR, PC BOARD (PLUG) 5P
R1326 1-216-061-00 METAL CHIP 3.3K 5% 1/10W CNP113 1-779-366-11 CONNECTOR, BOARD TO BOARD 4P
R1327 1-216-061-00 METAL CHIP 3.3K 5% 1/10W CNP114 1-779-366-11 CONNECTOR, BOARD TO BOARD 4P
R1328 1-216-061-00 METAL CHIP 3.3K 5% 1/10W CNP115 1-779-366-11 CONNECTOR, BOARD TO BOARD 4P
CNP116 1-779-366-11 CONNECTOR, BOARD TO BOARD 4P
R1329 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
R1330 1-216-061-00 METAL CHIP 3.3K 5% 1/10W CNS103 1-784-772-11 CONNECTOR, FFC 11P
R1331 1-216-073-00 METAL CHIP 10K 5% 1/10W CNS104 1-784-743-11 CONNECTOR, FFC 21P
R1332 1-216-073-00 METAL CHIP 10K 5% 1/10W CNS107 1-770-397-11 HOUSING, CONNECTOR(PC BOARD)4P
R1401 1-216-025-91 RES,CHIP 100 5% 1/10W
< DIODE >
R1402 1-216-025-91 RES,CHIP 100 5% 1/10W
R1403 1-216-025-91 RES,CHIP 100 5% 1/10W D101 8-719-313-45 DIODE SEL6810A-TH10
R1404 1-216-097-91 RES,CHIP 100K 5% 1/10W D102 8-719-024-99 DIODE 11ES2-NTA2B
R1405 1-216-025-91 RES,CHIP 100 5% 1/10W D103 8-719-911-19 DIODE 1SS119
R1406 1-216-073-00 METAL CHIP 10K 5% 1/10W D104 8-719-046-39 DIODE SEL5821A-TH15
D105 8-719-046-39 DIODE SEL5821A-TH15
R1407 1-216-295-91 SHORT 0
R1408 1-216-025-91 RES, CHIP 100 5% 1/10W D106 8-719-046-39 DIODE SEL5821A-TH15
R1409 1-216-025-91 RES, CHIP 100 5% 1/10W D108 8-719-046-39 DIODE SEL5821A-TH15
R1410 1-216-295-91 SHORT 0 D119 8-719-046-39 DIODE SEL5821A-TH15
D122 8-719-046-39 DIODE SEL5821A-TH15
< VIBRATOR > D180 8-719-911-19 DIODE 1SS119
C101 1-104-664-11 ELECT 47uF 20% 16V L101 1-410-509-11 INDUCTOR 10uH
C104 1-126-964-11 ELECT 10uF 20% 50V
C105 1-104-905-11 CAPACITOR 0.22F 5.5V < TRANSISTOR >
C106 1-164-159-11 CERAMIC 0.1uF 50V
C107 1-164-159-11 CERAMIC 0.1uF 50V Q101 8-729-119-76 TRANSISTOR 2SA1175-HFE
Q102 8-729-900-36 TRANSISTOR DTC124ES
C108 1-164-159-11 CERAMIC 0.1uF 50V Q103 8-729-900-36 TRANSISTOR DTC124ES
C109 1-164-159-11 CERAMIC 0.1uF 50V Q104 8-729-900-36 TRANSISTOR DTC124ES
C110 1-164-159-11 CERAMIC 0.1uF 50V Q105 8-729-900-36 TRANSISTOR DTC124ES
C111 1-164-159-11 CERAMIC 0.1uF 50V
C112 1-164-159-11 CERAMIC 0.1uF 50V Q106 8-729-900-36 TRANSISTOR DTC124ES
Q107 8-729-900-36 TRANSISTOR DTC124ES
C113 1-164-159-11 CERAMIC 0.1uF 50V Q108 8-729-900-36 TRANSISTOR DTC124ES
C117 1-164-159-11 CERAMIC 0.1uF 50V Q109 8-729-900-36 TRANSISTOR DTC124ES
C118 1-164-159-11 CERAMIC 0.1uF 50V Q110 8-729-900-36 TRANSISTOR DTC124ES
C119 1-104-664-11 ELECT 47uF 20% 16V
C120 1-164-159-11 CERAMIC 0.1uF 50V
— 74 —
INPUT
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
< IC > R346 1-249-397-11 CARBON 22 5% 1/4W F
R347 1-249-397-11 CARBON 22 5% 1/4W F
IC301 8-759-805-14 IC LC7822 R351 1-249-401-11 CARBON 47 5% 1/4W F
IC302 8-759-636-74 IC M5218AP-22 R352 1-249-441-11 CARBON 100K 5% 1/4W
IC304 8-759-634-50 IC M5218AL R353 1-249-440-11 CARBON 82K 5% 1/4W
IC401 8-759-231-59 IC TA7815S
IC402 8-759-245-87 IC TA7915S R354 1-249-408-11 CARBON 180 5% 1/4W F
R355 1-249-428-11 CARBON 8.2K 5% 1/4W F
IC403 8-759-604-39 IC M5F78M12 R356 1-249-441-11 CARBON 100K 5% 1/4W
IC404 8-759-708-05 IC NJM78L05A R357 1-247-807-31 CARBON 100 5% 1/4W
IC405 8-759-634-50 IC M5218AL R358 1-249-441-11 CARBON 100K 5% 1/4W
IC406 8-759-634-50 IC M5218AL
IC407 8-759-634-50 IC M5218AL R359 1-249-413-11 CARBON 470 5% 1/4W F
R360 1-249-417-11 CARBON 1K 5% 1/4W F
IC414 8-759-534-63 IC TC9299P R361 1-249-417-11 CARBON 1K 5% 1/4W F
IC415 8-759-534-63 IC TC9299P R362 1-249-417-11 CARBON 1K 5% 1/4W F
IC416 8-759-534-63 IC TC9299P R365 1-249-437-11 CARBON 47K 5% 1/4W
IC501 8-759-326-52 IC uPC2581V
IC601 8-759-326-52 IC uPC2581V R381 1-249-441-11 CARBON 100K 5% 1/4W
R385 1-249-437-11 CARBON 47K 5% 1/4W
IC701 8-759-326-52 IC uPC2581V ! R387 1-249-410-11 CARBON 270 5% 1/4W F
R388 1-249-417-11 CARBON 1K 5% 1/4W F
< JACK > R389 1-249-417-11 CARBON 1K 5% 1/4W F
R306 1-249-441-11 CARBON 100K 5% 1/4W R456 1-249-434-11 CARBON 27K 5% 1/4W
R307 1-247-807-31 CARBON 100 5% 1/4W R457 1-249-437-11 CARBON 47K 5% 1/4W
R308 1-249-441-11 CARBON 100K 5% 1/4W R458 1-249-437-11 CARBON 47K 5% 1/4W
R309 1-249-413-11 CARBON 470 5% 1/4W F R459 1-249-437-11 CARBON 47K 5% 1/4W
R310 1-249-417-11 CARBON 1K 5% 1/4W F R501 1-249-417-11 CARBON 1K 5% 1/4W F
R336 1-249-425-11 CARBON 4.7K 5% 1/4W F R552 1-249-439-11 CARBON 68K 5% 1/4W
R337 1-249-441-11 CARBON 100K 5% 1/4W R553 1-249-439-11 CARBON 68K 5% 1/4W
R338 1-249-417-11 CARBON 1K 5% 1/4W F R554 1-249-421-11 CARBON 2.2K 5% 1/4W F
R339 1-249-417-11 CARBON 1K 5% 1/4W F R590 1-249-433-11 CARBON 22K 5% 1/4W
R340 1-249-417-11 CARBON 1K 5% 1/4W F ! R592 1-249-381-11 CARBON 1 5% 1/4W F
S124 1-762-750-11 SWITCH, TACTILE (CD) J201 1-766-399-11 JACK, PIN 3P (MONITOR/VIDEO1)
S125 1-762-750-11 SWITCH, TACTILE (0) J202 1-766-400-11 JACK, PIN 2P (VIDEO2)
S126 1-762-750-11 SWITCH, TACTILE (5) J203 1-766-400-11 JACK, PIN 2P (TV/DBS)
S127 1-762-750-11 SWITCH, TACTILE (TAPE) J204 1-563-330-11 JACK (S-LINK)
S128 1-762-750-11 SWITCH, TACTILE (VIDEO1)
< RESISTOR >
S130 1-762-750-11 SWITCH, TACTILE (VIDEO2)
************************************************************ R201 1-247-804-11 CARBON 75 5% 1/4W
R202 1-247-804-11 CARBON 75 5% 1/4W
* 1-670-000-11 TUNER BOARD R203 1-247-804-11 CARBON 75 5% 1/4W
************ R204 1-247-804-11 CARBON 75 5% 1/4W
R205 1-247-804-11 CARBON 75 5% 1/4W
< CAPACITOR >
R206 1-247-804-11 CARBON 75 5% 1/4W
C382 1-161-494-00 CERAMIC 0.022uF 25V R207 1-247-804-11 CARBON 75 5% 1/4W
RRR4 1-249-417-11 CARBON 1K 5% 1/4W F
< CONNECTOR > ************************************************************
— 79 —
STR-DE725
VOLUME
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
* A-4414-304-A VOLUME BOARD, COMPLETE < VARIABLE RESISTOR >
************************
(Including L.B BOARD) RV401 1-225-446-11 RES, VAR, CARBON 100K × 6
(MASTER VOLUME)
< CAPACITOR > RV402 1-238-965-21 RES, VAR, CARBON 100K/100K (BALANCE)
************************************************************
C410 1-126-233-11 ELECT 22uF 20% 50V
C411 1-126-233-11 ELECT 22uF 20% 50V MISCELLANEOUS
C412 1-126-233-11 ELECT 22uF 20% 50V *************
C413 1-162-199-31 CERAMIC 10PF 5% 50V
C414 1-162-199-31 CERAMIC 10PF 5% 50V 12 1-773-161-11 WIRE (FLAT TYPE) (21 CORE)
13 1-769-959-11 WIRE (FLAT TYPE) (11 CORE)
C415 1-162-199-31 CERAMIC 10PF 5% 50V 66 1-773-285-11 WIRE (FLAT TYPE) (29 CORE)
C421 1-162-286-31 CERAMIC 220PF 10% 50V ! 73 1-769-743-11 CORD, POWER
C422 1-162-286-31 CERAMIC 220PF 10% 50V 76 1-769-876-11 WIRE (FLAT TYPE) (7 CORE)
C423 1-162-286-31 CERAMIC 220PF 10% 50V
C460 1-126-233-11 ELECT 22uF 20% 50V ! T901 1-431-887-11 TRANSFORMER, POWER
! TM301 1-693-407-11 TUNER
C461 1-126-233-11 ELECT 22uF 20% 50V ************************************************************
C462 1-126-233-11 ELECT 22uF 20% 50V
C463 1-162-199-31 CERAMIC 10PF 5% 50V ACCESSORIES & PACKING MATERIALS
C464 1-162-199-31 CERAMIC 10PF 5% 50V ********************************
C465 1-162-199-31 CERAMIC 10PF 5% 50V
1-501-374-11 ANTENNA, LOOP
C471 1-162-286-31 CERAMIC 220PF 10% 50V 3-810-765-11 MANUAL, COMMONNESS INSTRUCTION
C472 1-162-286-31 CERAMIC 220PF 10% 50V (ENGLISH)
C473 1-162-286-31 CERAMIC 220PF 10% 50V 3-864-230-11 MANUAL, INSTRUCTION (RM-PP401)
(ENGLISH)
< CONNECTOR > 3-864-484-11 MANUAL, INSTRUCTION (ENGLISH)
8-917-634-90 REMOTE COMMADER RM-PP401
CNP101 1-770-388-11 PIN, CONNECTOR (PC BOARD) 4P
* CNS402 1-564-726-11 PIN, CONNECTOR (SMALL TYPE)10P 4-987-977-01 LID, BATTERY CASE (For RM-PP401)
************************************************************
< IC >
**************
IC408 8-759-634-50 IC M5218AL HARDWARE LIST
IC409 8-759-634-50 IC M5218AL **************
IC410 8-759-634-50 IC M5218AL
#1 7-685-646-79 SCREW +BVTP 3 × 8 TYPE2 TT (B)
< RESISTOR > #2 7-685-881-09 SCREW +BVTT 4 × 8 (S)
#3 7-685-872-09 SCREW +BVTT 3 × 8 (S)
R108 1-249-411-11 CARBON 330 5% 1/4W
R413 1-249-437-11 CARBON 47K 5% 1/4W
R414 1-249-437-11 CARBON 47K 5% 1/4W
R415 1-249-437-11 CARBON 47K 5% 1/4W The components identified by mark ! or dotted
R416 1-249-429-11 CARBON 10K 5% 1/4W line with mark ! are critical for safety.
Replace only with part number specified.
R417 1-247-843-11 CARBON 3.3K 5% 1/4W
R418 1-249-437-11 CARBON 47K 5% 1/4W
R419 1-249-437-11 CARBON 47K 5% 1/4W
R420 1-249-437-11 CARBON 47K 5% 1/4W
R421 1-249-437-11 CARBON 47K 5% 1/4W