Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 72 views

    W600 TechManual

    Uploaded by

    Tauqeer Raza

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF or read online from Scribd

    W600 TechManual

    Uploaded by

    Tauqeer Raza
    72 views30 pages

    Original Title

    W600_TechManual

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    PDF or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF or read online from Scribd
    Download as pdf
    72 views30 pages

    W600 TechManual

    Uploaded by

    Tauqeer Raza

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF or read online from Scribd
    Download as pdf
    You are on page 1of 30
    VV S oO oO Series Technical Manual 4€é PEGASUS. CONTENTS “Threading 29-30 Replacing needles a1 Needless : . [Adjusting tend tention Adjusting presser foot pressure ~~ Adjusting ciflerential feed raion ‘Adjusting stitch length Installation of Machine Schematic diagram ‘Assembling machine rest boar Instaling swing head: Instaling belt cover Lubrication To add ol to HR devices ‘Machine pulley tuning direction: S4eeeee Lubrication Oitlever Lrication Oilonange Todaain olemnnesannemnnmremnmntnnentenennn ‘Checking and replacing olfiter 38 28 a8 ey 28 ‘Adjustment and Maintenance Adjusting needle height ‘Adjusting looper [Adjusting looper front to-back-motion ‘Adjusting needle guard (rear) ‘Adjusting needle guard (ron!) Postoning spreader ‘Adjusting spreader travel Positioning spreader thread guide Instaling toad guide ‘Adjusting feed dog tit ‘Adjusting feed dog height. Acting fot hit Adjustments ciffarential Foed Ratio. Differential feed rao for standard specications: “To use the diferential fed ratio range 1:1.2-1:1.8« {Adjusting Throad Take-up and Thread Guide Adjusting needle trond take-up Adjusting needle trond guides ‘Adjusting needle toad guard Adjusting spreader thead take-up ‘Adjusting looper throad take-up ~ Instaling looper thread guard Setting thread guides @ and @ ~ Timing Adjustment Adjusting timing of needle motion and looper let-o-ight motion ‘Adjusting ining of nose metion and looper font o-back mation Adjusting neodle quar (rear) timing Ajstig spreader timing ‘Adjusting neodle thread tako-up ting Metering Device Adjustment (MD231) MD231 (elastic feeder) Instaling ace guide Lubrication Lubricating eaten Lubricating bearings: Positioning lace guide (wer) Positioning elastic ques Adjusting elastic feeding amount nen Adjusting tention of elastic : Lace guide (L210) Instaling taco guide 1240 (ar immen Lubrication Adjusting tabs qui ‘Adjusting presser foo tit ‘Adjusting upper knife prossue [Agjusing lower knife holder lito right ‘Adjusting the height of upper knife holder Replacing upper kilo . Replacing lower nile RP Device (ea ule Lubrication Manual levor ‘Adjusting roller pressure ‘Ajusting fabric feeding amount: 48 48 48 49 40 sa 53 52 53 54 54 “54 54 55 55 55 55 ‘The following are instructions for operator to operate the machine correaly ‘Observe these instructions. (1) Tum the machine off withthe push button @ under the table. ‘Caution! ‘When a clutch motor is used, f will keep on running for a while by inertia after the power is tured off. ‘The machine will operate if the Treadle @ is pressed by some chance. To prevent accidents, keep the Treadle @ on after the power is umed off until the machine stops 29

    You might also like