POLYMER FOAMS

3.063 Polymer Physics

Spring 2007

Katrine Sivertsen

 Introduction

It is hard to go a day without coming across some sort of polymer foam. Polymer

foams are found virtually everywhere in our modern world and are used in a wide variety of

applications such as disposable packaging of fast-food, the cushioning of your furniture and insulation

material.

Polymer foams are made up of a solid and gas phase mixed together to form a foam.

This generally happens by combining the two phases too fast for the system to respond in a smooth

fashion. The resulting foam has a polymer matrix with either air bubbles or air tunnels incorporated in

it, which is known as either closed-cell or open-cell structure. Closed-cell foams are generally more

rigid, while open-cell foams are usually flexible.

The gas that is used in the foam is termed a blowing agent, and can be either chemical

or physical. Chemical blowing agents are chemicals that take part in a reaction or decompose, giving

off chemicals in the process. Physical blowing agents are gases that do not react chemically in the

foaming process and are therefore inert to the polymer forming the matrix.

Polymer foams are produced in a number of different ways. Examples are through

slab-stock by pouring, extrusion and different forms of molding.

Polymer foams can be divided into either thermoplastics or thermosets, which are

further divided into rigid or flexible foams. The thermoplastics can usually be broken down and

recycled, while thermosets are harder to recycle because they are usually heavily crosslinked.

Issues facing the polymer foam industry is that of waste disposal, recyclability,

flammability and the effect of blowing agents on the environment. The restrictions on the use of

CFC's (chloro-fluoro-carbons) has become very important in making polymer foams more

environmentally friendly. Advances in biodegradable foam materials are also helping to improve the

recyclability and waste disposal.

 The reason polymer foams are so widely used is that they have a lot of advantageous

properties. The density is low, and so the weight reduction compared to other options is significant.

Some polymer foams have very low heat transfer, making them optimal insulators. Many are flexible

and soft, meaning they provide more comfort when used for furniture and bedding.

Through this paper I will examine these topics, and specifically focus on polyurethane

foam as one of the most common polymer foams used in everyday life and applications.

Brief history

Polymer foams were first made in the 1930's and -40's, with foamed polystyrene being

the first polymer foam in 1931. Polyurethane was invented by Dr. Otto Bayer at the start of the

second World War. It was first used as a replacement for rubber and also used as a coating to protect

other common materials at the time such as metals and wood.

A few years after the war, the flexible polyurethane foam was invented and it was first

then that it started being used for cushioning in furniture and automotive industry.

The two decades following made polymer foams more widely used as new

technologies developed, introducing methods such as injection molding, twin screw for foam and

several extrusion techniques.

The use of blowing agents that contributed to the ozone layer depletion raised concerns

in later years and has lead to a focus on finding blowing agents that will not have a negative

environmental impact.

Types of polymer foam

Polyurethane

Polyurethanes are any type of polymer containing a urethane linkage. The urethane

linkage is -NH-CO-O-. The way to form polyurethanes is done by reacting isocyanates with

compounds that have an active hydrogen, such as diols, that contain hydroxyl-groups, in the presence

of a catalyst. Since there are many compounds containing active hydrogens and many different
diisocyanates, the number of polyurethanes that can be synthesized is also large. The specific

properties of the polyurethane can be tailored to a specific need by combining the appropriate

compounds.

Polyurethanes can exist as both rigid and flexible foams, and as a coating or adhesive

material. Since polyurethanes come in so many forms and can have a wide variety of properties, it is

also used in many different applications. Rigid polyurethanes are used as insulation and flotation,

while flexible ones are used for cushioning and packaging. In addition, they are used as adhesives in

construction and transportation. Rhinoskin is an example of a polyurethane used for coating and

protection. It is sprayed onto a surface and then sets to protect the underlying layer.

Polyurethanes are mostly thermosets, which means they are hard to melt and reprocess

and can therefore have the disadvantage of being non-recyclable.

Biodegradable foams

Biodegradable polymer foams are investigated not only because of the increasing

waste and environmental problems for traditional polymer foams, but also because of the increasing

price of petroleum products that are used in manufacturing the polymer foams.

Biodegradable foams are water soluble and sensitive to humidity, while traditional

petroleum-based foams are more inert to water. Biodegradable foams are also limited in making

foams that have microcellular structure, which means they will be hard to make into thin sheets.

However, they are important in reducing the amount of CO2 emission. There is also a

wide range of different candidates of biomaterials that can be used for biodegradable foams, including

ethylene vinyl alcohol, polyvinyl alcohol, polycaprolactone, polylactic acid and starch.

Starch

Starch foam was made already in 1989 as biodegradable packaging, and is an

alternative material to the traditional polystyrene foams. Starch is a polysaccharide made up of

glucose units linked by glycoside linkages, and its length is generally between 500-2000 repeat units.
Starch is made up of amylose and amylopectin Amylose is more linear and gives the foam flexibility

and keeps the density low, while amylopectin is highly branced and makes the product more

foamable. Starch can be extracted from for example corn or potatoes.

Starch foams are produced by extrusion where the starch is melted and mixed with a

blowing agent. The blowing agent for starch is often water or methanol, which is turned into steam

when the system is heated and forms air bubbles within the starch matrix. The extrusion process is a

continuous, low-cost method that is easy to use. It is still hard to make the foam smooth and have a

high number of closed cells. The use of thermoplastic polymer additives can help even out the

surfaces, but can also decrease the degradability of the foam by incorporating slowly degrading or

non-degradable polymers.

Synthesis

Polyurethane

As mentioned earlier polyurethanes are made by the addition reaction of

polyisocyanates and polyols. When there are two functional groups it's termed a diisocyanate and diol

as seen below.

http://www.pslc.ws/mactest/uresyn.htm

Figure 1: Reactants used for polyurethane

Along with a nucleophile like diazobicyclo[2.2.2]octane (DABCO), the mixing of

these two monomers will form a dimer, which again will continue to react with other monomers,
dimers and oligomers and form long polyurethane chains.

The positive charge due to oxygen's electronegativity on the hydrogen at the end of the

diol attracts the nucleophile, which wants to bind to a nucleus (nucleophile=nucleus loving). The

oxygen then becomes more negative and reacts with a carbon on an isocyanate group. This leaves the

nitrogen on the isocyanate group to be negative, which is highly unfavorable. The nitrogen will give

off its negative charge to the hydrogen atom on the alcohol group, finally forming a urethane bond

between the two monomer units, resulting in a urethane dimer. The dimer will have one end group

that is isocyanate, while the other is an alcohol group. Each end can now react with other monomers

and oligomers until polyurethane is formed. This is called a step-growth reaction. Step-growth

reactions are characterized by longer chains being able to react and add to a growing chain just like

monomers can, unlike chain-growth polymerization where only monomers can add to the growing

chain. It is also an addition reaction since no small compounds are given off during the reaction.

http://www.pslc.ws/mactest/uresyn.htm

Figure 2: the DABCO attaches to the hydrogen of the alcohol group. The negative oxygen then reacts

with the carbon on the isocyanate group, leading to a negative nitrogen. The nitrogen gives off its charge to the
hydrogen and the two monomers become bound together to a dimer by a urethane linkage.

If instead of a diol, a macrodiol is used in the reaction, the polyurethane gets

alternating soft and rigid segments, where the macrodiol makes up the soft segments in between the

rigid blocks from the diisocyanate monomers.

The difference between making polyurethane and polyurethane foam is that a gas has

to be incorporated in the final product. To achieve this the isocyanate group is reacted with water

forming an amine and CO2 gas. Because the isocyanate group turns into an amine, the reaction with

other diisocyanates will result in some urea-linkages in the polyurethane foam, but this doesn't affect

the properties of the polymer foam much, and is necessary to get the gas to be produced and expand

the polymer into a foam.

http://www.pslc.ws/mactest/foamsyn.htm

Figure 3. The reaction of water with isocyanate group forms and amine group and expels carbon

dioxide gas.

Blowing agents

As seen in the last paragraph, water was used as a blowing agent to produce CO2.

Because the water needed to be part of a reaction, it's a chemical blowing agent. Physical blowing

agents don't take part in a chemical reaction, but are volatile liquids that evaporate and make the foam

expand. First generation physical blowing agents are mostly outruled because of their negative
environmental impact on the ozone layer. This is especially the case for chlorofluorocarbons.

CFC's and HCFC's

CFC's are ideal blowing agents besides the tremendous environmental concerns

associated with them. They are not flammable, have fitting boiling points and are non-toxic. They

also have good thermal insulation properties.This is why it has been hard to find a replacement for

these blowing agent that has equivalent properties.

Hydrochlorofluorocarbons (HCFC) and hydrofluorocarbons (HFC) are blowing agents

with a lot smaller impact on the ozone layer and with similar properties. HCFC's are being phased out

since they still have ozone depletion problems. Although HFC's have no impact on the ozone

depletion, it has high global warming potential. However, they have a lower shelf life and can

sometimes be flammable, which creates concern because this decreases the safety of polyurethane

foams.

CO2

Liquid CO2 is used as a blowing agent because it does not have the same

environmental issues as CFC's and HCFC's. It has a low global warming potential and is inexpensive.

It is also easier to obtain low density foams using CO2.

Manufacturing methods

Slabstock

Slabstock processing has its name from the way that the foam is cut into large slabs

after being processed, instead of formed into specific geometric shapes. The materials are spread onto

a conveyor through a mixing head, and the foam forms on the conveyor constrained by walls so the

foam forms a large slab of material. The foam is then cut into suitable size slabs.
 Image removed due to copyright restrictions.

Please see Harrington, R. and Hock, K. Flexible Polyurethane Foams, 2nd ed. Midland,
MI: Dow Chemical Company, 1998.

http://scholar.lib.vt.edu/theses/available/etd-12032002-170009/unrestricted/02_Chapter_1.pdf

Figure 4: The foam is mixed and poured onto a conveyor and forms one large continuous piece that is

cut into slabs.

Molding

Molding processes can be divided into either cold-molded or hot-molded processes,

differing by their molding temperatures. The process injects foam into separate formed molds and

shapes the foams into individual pieces with the same shapes. This process is more complicated than

slabstock and more costly.

Image removed due to copyright restrictions.

Please see Harrington, R. and Hock, K. Flexible Polyurethane Foams, 2nd ed. Midland,
MI: Dow Chemical Company, 1998.

http://scholar.lib.vt.edu/theses/available/etd-12032002-170009/unrestricted/02_Chapter_1.pdf

Figure 5: Individual molds on a turntable. The mixing head inserts an equal and discrete amounts of

material into each mold. The molds are made to form the foam into specific geometries.
 Properties of polymer foams

Structure

As mentioned earlier foams can be divided into open-cell and closed-cell structures.

However, the term cell in this context is somewhat different than what it is usually considered as. In

all foams the cell or pore structure is not a specific uniform unit, there is instead a wide range of

different sized cells and pores and a certain amount that are closed-cell and open-cell although one

will be the dominating structure.

Image removed due to copyright restrictions.

Please see http://ciks.cbt.nist.gov/%7Egarbocz/closedcell/img54.gif

Figure 6: A model of a closed-cell structure where all the pores are constrained by polymer matrix

walls.

Image removed due to copyright restrictions.

Please see http://irc.web-t.cisti.nrc.ca/cbd/figures/166f03.gif

Figure 7: Open cell structure of polyurethane foam at 20x magnification. The pores are not enclosed

but form a continous network.

 Since the size and shape of the cells or pores are very disperse the best approach to

describe foam structures is through statistical models, since there is never a regular packing of

spherical cells in a foam. The models used range from cells being modeled as spheres, polygons and

dodecahedrons.In addition the cells are usually elongated in a certain direction as the polymer is

foamed, making it harder to model the foam as any ideal model. It is not only the polymer itself that

contributes to the properties of the foam, but the gas-filled space between them. In comparison to

other non-polymeric foams where the voids or gas-filled spaces do not interact with the surrounding

matrix, in polymer foams the intercellular gas interacts with the matrix and affects its properties and

behaviors and can change them over time.

The parameter G is the relative geometrical volume and φg is the volume fraction of

cells/pores which the gas occupies. The total volume is the sum of the volume fraction of the gas,

polymer and moisture, since the foam always sucks up some moisture from the environment.

G is the quotient of the total number of voids over the net volume.

G= Vg/Vo

The gas-filling factor is a similar parameter that is often more convenient. It is the

quotient of the total number of voids over the solid phase volume.

G= Vg/Vs

The volume fraction of cells/pores is

φg= (ρp-ρ)/ρp

which is the difference between the density of the unexpanded polymer and the

apparent density of the foamed polymer over the unexpanded polymer density. This formula neglects

the weight of the gas in the pores.

This can also be written in terms of the mass and density of the gas:
 φg= (mg)/ (Vo ρg)

The amount of pores in the foam structure affects many of its properties. When there

are more and smaller pores the foam is a much better insulator, because the gas basically cannot

transfer heat and the heat convection has to find its way around all the pores. The more pores there

are the more tortuous the path, and there is less chance of the heat transfer happening effectively. In

this case, the gas phase is more dominant in determining the foam properties than the actual polymer.

The mechanical response of the foam is also dictated by the structure. In an open-cell

structure the gas phase is not held together and the foam can compress much more. The foam will

reform by sucking up air again, but will not be able to mimic its original shape exactly and the

strength and energy absorption of the system will be weaker.

The size of the cell also affects the properties of the foam. Foams with smaller cells

are better at energy absorption. At smaller cell sizes the amount of open-cell structure also decreases.

Mechanical

Since gas has the least mechanical strength, the more gas there is the less strong the

foam will be, which means the lower density foams exhibit the smallest Young's modulus. Even if the

cells of the foam have varying shape, there is usually some anisotropy to the foam because of the

direction it is being formed at. The strength is better along the direction of foaming. If the ratio of

height to width of a cell is increased by a certain amount, the compressive strength and the tensile

strength of the foam also increases by the same amount. So the geometry of the cells could have

more to say for the strength than density, chemistry and the amount of open-cells in the structure.

Open-cell structures have the disadvantage of lower mechanical properties, but is

much better at sound absorption. Because the open-cell structure affects the modulus of the foam, this

must be taken into account when calculating the modulus.

The modulus is:

Mf/Mp = (1-x)φ2 (ρf/ ρp )+x (1-φ)(ρf//ρp)

 where Mf is the modulus of the foam and Mp is the modulus of the polymer. Φ is the

vlume fraction and ρ is the density, with the subscripts f and p for foam and polymer. X is the closed-

cell fraction.

Impact absorption is a key advantage of polymer foams over the unfoamed polymer.

The cells deform to absorb the energy impact and then reform when the load is removed. The

polymer foam has to be able to resist multiple loadings, and resisting change to the structure so the

loading can be repeated many times. If the foam is exposed to loads that are too large the cell walls

will rupture and the amount of open-cell structure will increase and weaken the mechanical properties

of the foam.

Thermal conductivity

The total thermal conductivity is the sum of the conductivities of both the gas and solid

phase plus the thermal conductitvity due to convection and radiation. The thermal conductivity is very

low for polymer foams because the amount of solid in the foam is very small ( on the order of 3%

10% of the total volume). The fraction of solid used is not always minized though, because of a

decrease in mechanical strength of the foam or because it is harder to produce low density foams for

some raw materials.

The gas phase contributes the most to heat transfer. The thermal conductivity of a gas

decreases with an increase in molecular weight, so a heavy gas is more desirable as a blowing agent,

although this is not always possible either because of cost or convenience. After usage and time the

gas phase in the foam is replaced by air which has just a slightly higher thermal conductivity than

some heavier blowing agents like CFC's and CO2. The larger molecular weight compounds also

diffuse much slower through the polymer matrix, and the replacement of air into the foam goes much

slower, keeping the thermal conductivity as low as possible.

Radiative heat transfer happens through cell walls, so a foam with many small cells

will transfer less heat than a foam with a small amount of large cells. The cell size has a larger impact
than just changing the density.

Convective heat transfer only takes place in foams with very large cell sizes and is for

the most part negligible.

The thermal conductivity has a minimum at a certain density. At low densities the

radiative component is more dominant since the cell size is larger, and so is the convective

component. At high densities the number of cell walls and the thickness of them is higher so the

radiative component is less important, but the heat transfer through the solid phase becomes more

dominant.

Image removed due to copyright restrictions.

Please see http://www.scielo.br/img/revistas/jbsmse/v28n1/28260f1.gif

Figure 8: The lowest curve shows how low thermal conductvity foam has compared to other

insulating materials and that it has a minimum at a certain density value.

Flammability

The volatile liquids that are often used as blowing agents in foams and lead to easily

combustible foams. The flexible polyurethane foams are low density and have a lot of open-cell

structure, which means it is permeable to air. This means that it will easily burn when exposed to a
flame. This is a concern that the industry has to deal with in increasing the safety of their products.

One of the solutions is to use flame retardants in the foam. Chlorinated phosphate esters, chlorinated

paraffins, melamine powders and graphite are common as flame retardants.

Applications

Polyurethane foam

Rigid

Rigid polyurethane foams are mostly used in thermal insulation applications such as

refrigerators, freezeres, insulated buildings, insulated trucks carrying produce, water heaters,

thermoses etc. Hence, rigid polyurethanes contribute a lot to energy saving appliances.

Polyurethane foams with a high closed-cell structure are moisture resistant and

can be used as buoyancy in boats. The advantage is that the foam will not deflate upon a puncture, but

retains its buoyancy even after many load-unload cycles.

Flexible

Most of the flexible polyurethane foam produced is made for cushioning. This

includes furniture, packaging and transportation. Furnishings use polyurethane foam for carpet

underlay, bedding, home furniture. The transportation industry uses it in seating cushions for the

airlines, trains and bicycles and cars. It is also used in a wide range of other applications for cars such

as sound insulation and vibration dampening. Other applications include clothing, toys, electronics

and other applications for protection or cushioning issues.

Polystyrene foam

Polystyrene foam's most known application is the white polystyrene cups which are

ideal for hot beverages because of the foam's good thermal insulation properties. Polystyrene foam is

also used for packaging purposes, mostly food containers and disposable dishes and egg cartons.

High-impact polystyrene can also be used in structural appliances instead of rigid

materials like wood and metal.

Image removed due to copyright restrictions.

Please see http://www.scielo.br/img/revistas/jbsmse/v28n1/28260f1.gif

Figure 9: Examples of polystyrene applications

Conclusion

The structure is divided into open-cell or closed-cell foams, but most have a small

amount of the other as well. Production of the foams can happen in many different ways, slabstock

and molding were two that were mentioned here. Since polymer foams are used widely all over the

globe the technology to produce foams is continuously being improved.

Although many blowing agents are good in that it produces a satisfying product, the

environmental impacts can be large, so blowing agents such as CFC's and HCFC's are not in use

anymore. CO2 and other less environmentally dangerous substances are being used instead.

Polymer foams have great thermal insulation properties and can also be tuned to have

different mechanical strength and moisture absorption.

Polymer foams are widely used in all kinds of different applications because they can

be manufactured from many different types of polymers and there are plenty of different blowing

agents available to customize the foam to specific requirements. Polymer foams can be made to be

rigid or flexible by changing the chemistry, density, structure and raw materials used.

Bibliography
 Ashida, K. «Polyurethane and Related Foams», Taylor and Francis, 2007

Klempner, D., Sendijarevic, V. «Polymeric foams and Foam Technology» 2nd.ed.,

Hanser, 2004

Lee, S.-T., Park, C.B., Ramesh, N.S., «Polymer foams», Taylor and Francis, 2007

Khemani, K.C., «Polymeric foams», American Chemical Society, 1996

Throne, J., «Thermoplastic Foam Extrusion», Hanser, 2004

Gendron, R., «Thermoplastic Foam Processing», CRC Press, 2005

Uhlig, K., «Discovering polyurethanes», Hanser, 1999

«Center for the polyurethanes industry»,

<http://www.polyurethane.org/s_api/doc.asp?CID=853&DID=3488>, 16 May 2007

«Making polyurethanes», <http://www.pslc.ws/macrog/uresyn.htm>, 16 May 2007