Safety & Instruction Manual

WALTHER PPS Pistols

Read the instructions and warnings in this manual

CAREFULLY BEFORE using this firearm.

Walther America
2100 Roosevelt Avenue • Springfield, MA 01104
1-800-372-6454 • Fax: 413-747-3317
www.waltheramerica.com
 WARNING

READ THESE INSTRUCTIONS

AND WARNINGS CAREFULLY.
BE SURE YOU UNDERSTAND THESE
INSTRUCTIONS AND WARNINGS
BEFORE USING THIS FIREARM.
FAILURE TO READ THESE
INSTRUCTIONS AND TO FOLLOW
THESE WARNINGS MAY RESULT
IN SERIOUS INJURY OR DEATH
TO YOU AND OTHERS.

This SAFETY & INSTRUCTION

MANUAL should always
accompany this firearm and be
transferred with it upon change of
ownership or when presented to
another person.
A copy of the SAFETY & INSTRUCTION
MANUAL is available FREE
upon request from:

WALTHER AMERICA
CUSTOMER SUPPORT CENTER
2100 ROOSEVELT AVENUE
SPRINGFIELD, MA 01104
Phone: 1-800-372-6454
E-mail: customerservice@waltheramerica.com

2
Table of Contents

YOUR SAFETY RESPONSIBILITIES 4

SAFE STORAGE & TRANSPORTATION 7
PREPARATION FOR FIRING 8
AMMUNITION 9
MODEL NUMBER IDENTIFICATION 11
INSPECTING YOUR PISTOL 12
LOADED CHAMBER INDICATOR 13
LOADING 14
FIRING 16
CLEARING MISFIRES 17
UNLOADING 18
FIELD STRIPPING DISASSEMBLY 19
FIELD STRIPPING ASSEMBLY 21
REPLACING THE BACKSTRAP 23
MAGAZINE 24
SIGHT ADJUSTMENT 26
CLEANING, LUBRICATION, AND MAINTENANCE 26
WARRANTY 28
CONTACT & SHIPPING 29
ACCESSORIES 30

3
YOUR SAFETY RESPONSIBILITIES
SAFETY IS YOUR NUMBER ONE RESPONSIBILITY!!!!

At home, in the field, at the range, or anywhere, the first concern of every firearm
owner should be safety. Apply the following safety rules in every situation, with any
kind of firearm. If you feel uncertain about any operational aspects of your handgun,
please contact WALTHER at 1-800-372-6454 before proceeding with its operation.

WARNING: YOU MUST FOLLOW ALL OF THESE SAFETY RULES TO

ENSURE THE SAFE USE OF YOUR FIREARM. THE FAILURE TO
FOLLOW THESE BASIC FIREARM SAFETY RULES MAY RESULT IN AN
UNINTENDED DISCHARGE WHICH COULD CAUSE SERIOUS
PERSONAL INJURY OR DEATH TO YOU OR OTHERS.

! ALWAYS KEEP YOUR FIREARM POINTED IN A SAFE DIRECTION. Never

point a firearm at anyone or anything you do not intend to shoot, whether or
not it is loaded. This is particularly important when loading, unloading, or field
stripping the gun. ALWAYS control the direction of the firearm.
! ALWAYS TREAT EVERY FIREARM AS IF IT IS LOADED AND WILL FIRE
IF THE TRIGGER IS PULLED. Do not take anyone’s word that the firearm is
unloaded – always check for yourself. Never pass your firearm to another
person until the cylinder or action is open and you visually check that it is
unloaded. Keep your firearm unloaded and safely stored when not in use.
! NEVER PLACE YOUR FINGER INSIDE THE TRIGGER GUARD OR ON
THE TRIGGER UNLESS YOU INTEND TO FIRE. Ensure that other objects
do not touch the trigger.
! ALWAYS BE SURE OF YOUR TARGET AND WHAT IS BEYOND IT.
Always be sure of where the bullet will strike and shoot only where there is a
safe back stop free of obstructions, water or other surfaces which can cause
ricochets. Do not fire into the sky.
! NEVER CROSS OBSTACLES SUCH AS FENCES OR STREAMS WITH A
LOADED FIREARM.
! SAFE GUN HANDLING IS YOUR PERSONAL RESPONSIBILITY at all
times. Firearms are dangerous and can cause serious injury or death if they
are misused or used inappropriately. Safety must be the prime consideration
of anyone who owns or handles firearms.
Accidents are the result of violating the rules of safe gun handling and
common sense. Firearm safety training is available. Contact your dealer, law
enforcement agency, local sportsman’s club, etc. for availability.

4
YOUR SAFETY RESPONSIBILITIES CONT’D.
! YOU ARE RESPONSIBLE FOR THE FIREARM AT ALL TIMES.
In owning a firearm, you must undertake full-time responsibility for your
firearm’s safety and security. You must protect yourself and all others against
injury or death from misuse of the firearm 24 hours a day.
! FIREARM SECURITY IS YOUR RESPONSIBILITY.
You must secure firearms safely from children and/or unauthorized users.
Your firearm should always be kept unloaded and locked when not in use. A
lock has been provided for this purpose. Never assume that the use of this
lock is sufficient to safely secure your firearm. You must always evaluate
your personal situation and employ the security system(s) that meets your
needs and prevents children and unauthorized users from gaining access to
your firearm.
! APPROPRIATE USE FOR YOUR FIREARM MEANS USING YOUR
FIREARM FOR LEGAL PURPOSES.
For example - target shooting and lawful resistance of deadly criminal force.
It is your responsibility to ensure that you are in compliance with all
applicable laws and ordinances regarding the use of your firearm.
! NEVER RELY ON MECHANICAL FEATURES ALONE. Only your safe gun-
handling habits will ensure the safe use of your firearm. This is your
responsibility.
! ALWAYS SAFELY STORE AND SECURE YOUR FIREARM.
Safe and secure storage of your firearm is one of your most important
responsibilities. It is a full-time responsibility. You must always secure your
firearm and ammunition separately so that they are not accessible to children
and/or other unauthorized persons.
! NEVER KEEP AMMUNITION IN THE SAME LOCATION AS THE
HANDGUN.
Store each in a separate and secure place.
! ALWAYS WEAR EYE AND EAR PROTECTORS THAT ARE SPECIFIED
FOR FIREARM USE every time you discharge your firearm. Make sure
others in the vicinity of where you will be shooting do so as well.
! NEVER USE ALCOHOL OR DRUGS BEFORE OR WHILE SHOOTING.
Do not use your firearm if you are on any medication which impairs, even
slightly, your mental or physical ability.
! ALWAYS HAVE ADEQUATE VENTILATION.
Discharging firearms in poorly ventilated areas, cleaning firearms, or handling
ammunition may result in exposure to lead and other substances known to
cause birth defects, reproductive harm, and other serious physical injury.
Review the warnings and labels for all ammunition and cleaning products
carefully. Wash hands thoroughly after exposure.

5
 YOUR SAFETY RESPONSIBILITIES CONT’D.
! BEFORE HANDLING ANY FIREARM, UNDERSTAND ITS OPERATION.
Not all firearms are the same. Familiarize yourself with the mechanical
features of any firearm you intend to use. If you feel uncertain about any
operational aspects of your handgun, please contact WALTHER at
1-800-372-6454 before proceeding with its operation.
! NEVER ALLOW A FIREARM TO BE USED BY INDIVIDUALS WHO DO
NOT UNDERSTAND ITS SAFE OPERATION OR HAVE NOT READ THESE
FIREARM SAFETY RULES.
! ALWAYS USE THE CORRECT AMMUNITION FOR YOUR PARTICULAR
FIREARM as indicated by the marking on the barrel. Never use non-
standard, reloaded, or “handloaded” ammunition which has not been
subjected to internal ballistic pressure testing.
! BE SURE ALL ACCESSORIES, SUCH AS HOLSTERS AND GRIPS, ARE
COMPATIBLE with the handgun and that the accessories do not interfere
with safe operation.
! NEVER DISASSEMBLE YOUR HANDGUN beyond the field stripping
procedure outlined in this manual. Improper disassembly or reassembly of
your handgun may be dangerous and can lead to serious injury or death.
! NEVER MANIPULATE, ADJUST OR CHANGE ANY OF THE INTERNAL
COMPONENTS OF YOUR FIREARM including the firing pin, sear, or
drawbar.
Improper manipulation of any internal component may affect the safety and
reliability of your firearm and may cause serious injury or death.
! NEVER ALLOW ANY ALTERATION OR REPLACMENT OF PARTS IN
YOUR WALTHER FIREARM UNLESS PERFORMED BY A QUALIFIED
GUNSMITH using genuine WALTHER parts. If you do otherwise, improper
functioning of your firearm may occur and serious injury or death may result.

WARNING: SAFE USE OF A FIREARM IS YOUR PERSONAL

RESPONSIBILITY AND THE FAILURE TO FOLLOW ALL OF THESE BASIC
SAFETY RULES MAY RESULT IN SEVERE PERSONAL INJURY OR
DEATH TO YOU OR OTHERS.
YOU ARE THE MOST IMPORTANT SAFETY DEVICE WHEN IT COMES
TO THE USE OF YOUR FIREARM AND WALTHER WILL NOT BE
RESPONSIBLE FOR ANY PERSONAL INJURY, DEATH OR PROPERTY
DAMAGE THAT RESULTS FROM:
(1) THE CRIMINAL OR NEGLIGENT USE OF THIS HANDGUN;
(2) A DISREGARD OF THESE SAFETY INSTRUCTIONS AND
WARNINGS;
(3) IMPROPER OR CARELESS HANDLING OF THIS FIREARM;
(4) THE USE OF NON-STANDARD, DEFECTIVE, IMPROPER OR
RELOADED AMMUNITION; OR
(5) IMPROPER OR NEGLIGENT MODIFICATIONS OR REPAIRS
TO THE HANDGUN.

6
SAFE STORAGE & TRANSPORTATION
WARNING: FIREARMS ARE DANGEROUS WHEN USED AND STORED
IMPROPERLY THEY POSE A RISK OF SERIOUS OR FATAL INJURIES.
FIREARMS CAN BE ESPECIALLY DANGEROUS TO CHILDREN WHEN
THEY ARE STORED IN AN IRRESPONSIBLE AND UNSAFE MANNER.
FOR YOUR SAFETY AND THE SAFETY OF OTHERS, IT IS IMPERATIVE
THAT YOU KEEP YOUR FIREARM LOCKED AND UNLOADED IN A
SECURE PLACE.
THE AMMUNITION SHOULD BE STORED IN A SEPARATE, SECURE
LOCATION WHEN IT IS NOT IN USE.
SAFE AND SECURE STORAGE OF YOUR FIREARM IS ONE OF THE
MOST IMPORTANT RULES OF FIREARM SAFETY.
YOUR FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS
INJURY OR DEATH TO YOU OR OTHERS.

! ALWAYS SECURE YOUR FIREARM IN A MANNER THAT WILL PREVENT

UNAUTHORIZED ACCESS.
! Whenever your firearm is not in use, keep it unloaded and locked. Your
safety and the safety of others requires that you always secure and store
your firearm in a manner that will prevent unauthorized access. Never leave
a firearm unattended unless it is locked, unloaded and secured.
! ALWAYS USE THE LOCK PROVIDED BY WALTHER TO SECURE YOUR
FIREARM.
Please read and follow the instructions packaged separately for the use of
this lock. A lock, when properly used, can be an effective tool in preventing
unauthorized access to your firearm. There are other alternative locks and
safe storage containers available in the marketplace which may also be
appropriate for your particular needs. Consult your local gunshop, hardware
store, or local police department for guidance on the variety of other safe
storage devices or practices which may be appropriate for your particular
needs. By purchasing this firearm you have accepted the responsibility of
safely securing the firearm at all times and preventing its unauthorized use.
Never assume that the use of this lock alone is sufficient to safely secure
your firearm. It is your personal responsibility to select and use whatever
measures or practices that will enable you to be absolutely certain that your
firearm is secure at all times.

WARNING: NEVER LOCK A LOADED FIREARM

AND NEVER LOAD A LOCKED FIREARM!!

! ALWAYS STORE YOUR FIREARM AND AMMUNITION SEPARATELY so

that they are not accessible to children or other unauthorized persons. Safe
and secure storage of your firearm and ammunition are your responsibility. It
is a full-time responsibility.

7
 SAFE STORAGE & TRANSPORTATION CONT’D.
! NEVER ASSUME THAT A “HIDING” PLACE IS A SECURE STORAGE
METHOD.
Others may be aware of your storage location or come upon it by chance. It
is your personal responsibility to use common sense when storing your
firearm and ammunition and to always make sure they are not accessible to
children or other unauthorized persons.
! NEVER TRANSPORT A LOADED FIREARM.
When transporting your firearm, be sure it is unloaded and locked. Safe and
secure transportation of your firearm is your responsibility.
! ALWAYS FOLLOW THE LAW!
Many jurisdictions have laws that make it a crime to keep a firearm unlocked
and in an area accessible to children or others. Keeping a firearm locked and
unloaded when not in use is not only common sense safety practice... IT IS
THE LAW. You must be familiar with all local, state, and federal laws
regarding the safe storage and transportation of your firearm. Failure to know
and follow the law may result in unauthorized access or use of your firearm
by another. Obey all laws relating to the storage and transportation of
firearms. Your local police department or gunshop can furnish you with
available information on storing and/or transporting a firearm safely and
legally.
! YOUR FIREARM IS YOUR RESPONSIBILITY.
You must prevent your firearm from being stolen or from being used by
untrained or unqualified individuals. Keep it locked, unloaded and secured
when not in use.

PREPARATION FOR FIRING

WARNING: THE FAILURE TO FOLLOW THESE
FIREARM SAFETY REQUIREMENTS WILL CAUSE
SERIOUS PERSONAL INJURY OR DEATH TO YOU
OR OTHERS.

! ALWAYS TREAT ALL HANDGUNS AS IF THEY WERE LOADED.

! ALWAYS BE SURE THAT ALL CYLINDERS AND ACTIONS OF FIREARMS
ARE OPEN, THAT CHAMBERS ARE CLEAR OF CARTRIDGES,
MAGAZINES ARE REMOVED, AND THAT FIREARMS ARE POINTING IN A
SAFE DIRECTION.
! ALWAYS KEEP FINGERS AND OTHER PARTS OF YOUR BODY AWAY
FROM THE MUZZLE, AND AWAY FROM THE PISTOL SLIDE AND
EJECTION PORT.
! ALWAYS WEAR ADEQUATE AND PROPER EAR PROTECTORS
SPECIFIED FOR FIREARM USE to prevent permanent damage to your
hearing. Make sure others who are nearby are wearing ear protection as
well.

8
 PREPARATION FOR FIRING CONT’D.
! ALWAYS WEAR SAFETY GLASSES SPECIFIED FOR FIREARM USE,
whether indoors or out. Safety glasses should protect your eyes from the
firing flash and particles associated with the discharge of ammunition. Failure
to do so creates a risk of personal injury from particle or debris spitting or
ricochets.
! ALWAYS BE ALERT AND ALWAYS FOLLOW THE SAFETY
INSTRUCTIONS OF THE RANGE OFFICER.
Never shoot if you are tired, cold or impaired in any way.
! ALWAYS BE AWARE OF OTHER PEOPLE so that persons cannot
accidentally walk into the line of fire.
! THE SHOOTER (AND ALL OTHERS IN THE SHOOTING AREA) MUST
ALWAYS BE IN A POSITION THAT IS OUT OF THE LINE OF FIRE and are
not within an area where they may be struck by ricochets, particles spitting
from a revolver, or by ejected cases from other types of firearms.
! NEVER SHOOT AT HARD SURFACES, WATER OR UP INTO THE SKY.
Always select a place to shoot that has a safe backstop and is free from
obstructions and water surfaces which cause ricochets.
! NEVER USE ALCOHOL OR DRUGS BEFORE OR WHILE SHOOTING.

AMMUNITION
WARNING: NEVER USE AMMUNITION NOT SPECIFICALLY
DESIGNATED FOR USE IN YOUR FIREARM. FAILURE TO USE THE
CORRECT TYPE OR CALIBER OF AMMUNITION MAY CAUSE THE
FIREARM TO JAM, FAIL TO FIRE OR EVEN GENERATE EXCESSIVE
PRESSURE WHICH CAN DAMAGE OR EVEN RUPTURE YOUR
FIREARM, CAUSING PERSONAL INJURY, DEATH OR PROPERTY
DAMAGE.

Locate the caliber designation marked on

the handgun. This information indicates
the ammunition caliber that must be used
in this firearm. (See Figure 9.1).

You are responsible for selecting

ammunition that meets industry
standards and is appropriate in type and
caliber for this firearm.

Never use a cartridge not specifically FIGURE 9.1

designated for use in your firearm.
Pressure from the wrong type of ammunition may exceed the capability of your
firearm and may damage or even rupture your firearm.

Never mix ammunition.

9
AMMUNITION CONT’D.
In some cases, a round of ammunition not specified on your handgun may fit into the
chamber. Firing ammunition not specified on your handgun may cause it to rupture
and cause serious injury or death to you or others.

Always inspect your ammunition before using it. Never use dirty, corroded or
damaged ammunition which can lead to a burst cartridge which may cause damage
to the handgun and personal injury or death.

Use only commercially manufactured ammunition with internal ballistic pressures

which are in strict accordance with the specifications of the Sporting Arms and
Ammunition Manufacturers’ Institute (SAAMI). If you are uncertain, contact your
ammunition supplier for verification.

WARNING: NEVER USE NON-STANDARD, RELOADED OR

“HANDLOADED” AMMUNITION WHICH HAS NOT BEEN SUBJECTED TO
INTERNAL BALLISTIC PRESSURE TESTING.
RELOADED OR HANDLOADED AMMUNITION, MAY HAVE MANY
MANUFACTURING AND QUALITY VARIABLES (SUCH AS THE TYPE AND
AMOUNT OF GUN POWDER).
ANY AMMUNITION THAT IS IMPROPERLY MANUFACTURED, EVEN IN
THE SLIGHTEST DEGREE, MAY FAIL TO FIRE OR MAY GENERATE
EXCESSIVE INTERNAL PRESSURES WHICH CAN DAMAGE OR EVEN
RUPTURE THE FIREARM, CAUSING PERSONAL INJURY OR DEATH TO
THE SHOOTER OR THOSE IN THE IMMEDIATE VICINITY.

A firearm and ammunition are a system and must work together. Their performance
is closely related. There are different types of ammunition for different types of
firearms. Your firearm has been designed for ammunition of a specific type and a
specific caliber. It is important to select the proper ammunition for your firearm.

Different combinations of bullet velocity, bullet weight and firearm weight can have
major impact on felt recoil; high felt recoil can be uncomfortable to some shooters.

For example:
! Gun Weight: lower gun weight increases felt recoil.
! Bullet Weight: higher bullet weight increases felt recoil.
! Bullet Velocity: higher bullet velocity increases felt recoil.

To acclimate yourself to higher levels of felt recoil, consider the following:

! Use a firm two-hand hold on the grip when firing.
! Always start your shooting experience with the lowest bullet velocity and
lowest bullet weight available for your firearm.
! Ask your firearm dealer to suggest the lowest power, lowest velocity, lightest
bullet weight for your firearm.
! You can also consider changing your firearm’s grip configuration/composition
to better fit your hand’s specific size and shape.

10
AMMUNITION CONT’D.
“Plus-P” (+P) ammunition generates pressures in excess of the pressures associated
with standard ammunition. Such pressures may affect the wear characteristics of
your PPS pistol.
“Plus-P-Plus” (+P+) ammunition must not be used in WALTHER firearms. This
marking on the ammunition designates that it exceeds established industry
standards, but the designation does not represent defined pressure limits and
therefore such ammunition may vary significantly as to the pressures generated.
Some brands of ammunition may cause difficulty in extracting spent cartridge cases
from the chamber. If this situation occurs, thoroughly clean the chamber with solvent.
If this condition persists, we recommend changing to another brand of ammunition.

MODEL NUMBER IDENTIFICATION

Model Number Serial Number

FIGURE 11.1 FIGURE 11.2

Extractor
Slide Stop Notch
Front Sight Slide Slide Stop Rear Sight
Take Down Lever
Muzzle

Equipment
Rail Interchangeable
Frame Backstrap

Trigger Guard
Trigger
Magazine
Release
Grip

Magazine

FIGURE 11.3

11
INSPECTING YOUR PISTOL
! When you inspect your pistol, you should first check for yourself to ensure
that it is unloaded. To do this, grasp the pistol with your finger off the trigger
and outside the trigger guard, point the muzzle in a safe direction, depress
the magazine release and remove the magazine.
! Point the muzzle in a safe direction, grasp
the serrated sides of the slide from the rear
with the thumb and fingers as shown in
Figure 12.1, and briskly draw the slide fully
rearward in order to extract any cartridge
from the barrel chamber and clear it from the
pistol.
! Do not obstruct the ejection port because
doing so can interfere with ejection of a FIGURE 12.1
cartridge.
! Lock the slide in the open position by allowing the slide to move slightly
forward from the rearmost position while pressing upward on the slide stop.
! Check the barrel chamber to verify it is
unloaded and check the bore visually for any
obstructions (Figure 12.2).
! You must follow this procedure every time a
firearm leaves your hand, is cleaned, handed
to you or another person, transported or
stored.

FIGURE 12.2

WARNING: NEVER RELY ON MECHANICAL FEATURES ALONE. ONLY

YOUR SAFE GUN HANDLING WILL ENSURE THE SAFE USE OF YOUR
FIREARM. THIS IS YOUR RESPONSIBILITY.

MAGAZINE DISCONNECT FEATURE

WALTHER offers a magazine disconnect feature as an option on some PPS pistols.
To fully understand the function and operation of your pistol, perform the following
check:
! Remove the slide from the frame as described in “field stripping
disassembly”.
! If your pistol is NOT equipped with a Magazine Disconnect feature there will
not be a marking. (Figure 13.1)
! If your pistol is equipped with a Magazine Disconnect feature you will be able
to see a marking (M) as shown in Figure 13.2.

12
INSPECTING YOUR PISTOL CONT’D.

WARNING: IF YOUR PISTOL IS NOT EQUIPPED WITH THE MAGAZINE

DISCONNECT FEATURE YOUR PISTOL WILL FIRE WITH THE
MAGAZINE REMOVED FROM THE PISTOL.

FIGURE 13.1 FIGURE 13.2

LOADED CHAMBER INDICATOR

PPS pistols come with a loaded chamber indicator. This
indicator can be observed by looking at the top of the
slide/ejection port, (Figure 13.3) noting an opening at
the rear of the barrel hood.
By looking into this opening, you can observe whether
or not a round is in the firearm’s chamber. If a round is
in the chamber, you would see the actual brass or silver
colored rim through this opening.
FIGURE 13.3
WARNING: NEVER RELY UPON THE LOADED CHAMBER INDICATOR
ALONE TO VERIFY THE PRESENCE OR ABSENCE OF A ROUND IN THE
CHAMBER. THE SUREST METHOD TO DETERMINE THE PRESENCE OR
ABSENCE OF A ROUND IN THE CHAMBER IS TO VISUALLY CHECK THE
CHAMBER OF YOUR FIREARM BY REMOVING THE MAGAZINE AND
PULLING AND LOCKING THE SLIDE IN THE OPEN POSITION.

WARNING: ALWAYS TREAT EVERY FIREARM AS IF IT WERE LOADED

AND WOULD FIRE IF THE TRIGGER IS PULLED. A LOADED CHAMBER
INDICATOR MAY HELP DETERMINE WHETHER THE CHAMBER IS
LOADED OR UNLOADED. THE AMOUNT OF LIGHT, CLEANLINESS OF
THE PISTOL, DISCOLORATION OF THE AMMUNITION AND OTHER
FACTORS MAY LIMIT THE EFFECTIVENESS OF THE LOADED
CHAMBER INDICATOR.

13
LOADING
! Do not load the pistol until you have read and fully understand this manual.
! Do not load the pistol until you are ready to use it. Keep your finger off the
trigger and outside the trigger guard until you are ready to fire.
! Never load your pistol until you are sure of your target, what is beyond it and
are fully prepared to fire.
! WALTHER has provided you with a magazine designed to operate in your
specific model of pistol. While your magazine may be able to be inserted into
another model pistol, it will only function properly in the specific model for
which it was designed.
Do not interchange magazines from one model pistol to another model pistol.
! Follow instructions in this manual and any other specific instructions which
may be marked onto, or accompany, a magazine. Failure to use the
particular type of WALTHER magazine specified for your model and caliber
of pistol may result in a malfunction.
! Load the magazine by pressing a cartridge head
(rear of cartridge) downward on the forward
portion of the magazine follower (or downward
on the case of the previously loaded cartridge)
and sliding the cartridge fully under the lips of
the magazine until the cartridge head is against
the rear wall of the magazine. (Figure 14.1)
Repeat the procedure for the number of
cartridges you wish to load, up to the magazine
capacity (as described in the “Magazine” FIGURE 14.1
section). Do not attempt to load your magazine
with more than the specified number of cartridges because doing so can
cause a feeding failure.
! Inspect your pistol as previously described in the “Inspecting Your Pistol”
section. Hold the pistol in one hand with the muzzle pointing it in a safe
direction and with your finger off the trigger and outside the trigger guard.
Insert the loaded magazine into the magazine well (opening) of the pistol until
it is locked in place.
WARNING: VERIFY THAT THE FIRING PIN IS NOT PROTRUDING FROM
THE BREECH FACE.

WARNING: DO NOT USE EXCESSIVE UPWARD FORCE WHEN

INSERTING A LOADED MAGAZINE INTO THE PISTOL. EXCESSIVE
UPWARD FORCE COULD CAUSE THE SLIDE TO MOVE FORWARD,
CHAMBERING A ROUND AND MAKING THE PISTOL READY TO FIRE.

! To make sure that the magazine is fully and securely inserted, apply some
removal pressure to the exposed portion of the magazine floorplate.
! Pull the slide to the rear, press down on the slide stop to release the slide
and allow it to carry fully forward. This strips a cartridge from the magazine
and seats it in the chamber of the barrel.

14
LOADING CONT’D.
WARNING: IF THE CARTRIDGE FAILS TO STRIP FROM THE MAGAZINE
OR FULLY SEAT INTO THE CHAMBER, IMMEDIATELY STOP THE
LOADING PROCESS. REMOVE THE MAGAZINE, LOCK THE SLIDE OPEN
AND VERIFY THAT THE CHAMBER IS EMPTY. REFER TO THE
“INSPECTING YOUR PISTOL” SECTION OF THIS MANUAL.

WARNING: ALWAYS LOAD A ROUND INTO THE CHAMBER BY FEEDING

IT FROM THE MAGAZINE.
FAILURE TO FOLLOW THIS WARNING CAN RESULT IN SEVERE INJURY
OR DEATH TO YOU OR OTHERS.
NEVER ATTEMPT TO LOAD THE PISTOL BY INSERTING A ROUND INTO
THE OPEN EJECTION PORT.

CAUTION
The pistol can now be fired by pulling the trigger to the rear.
! If you wish to restore the magazine in your pistol to its full capacity, depress
the magazine release and remove the magazine from the pistol. Remember
that there is a round in the chamber; therefore, the weapon should be
holstered or safely secured during this process without touching the trigger.
Load one cartridge into the magazine to replace the one which was
chambered when you allowed the slide to carry forward.
! Re-insert the loaded magazine into the magazine well of the pistol until it is
locked in place. To make sure that the magazine is again fully and securely
inserted, apply some removal pressure to the exposed portion of the
magazine butt plate.
! Your pistol and its magazine are now fully loaded and will fire when the
trigger is pulled. Remember to keep your pistol pointed in a safe direction
under all conditions and always keep your finger or any other object off the
trigger and outside the trigger guard until you have made the commitment to
fire the handgun. Never leave a loaded firearm out of your direct control.
WARNING: PISTOLS WITH A MAGAZINE DISCONNECT FEATURE WILL
BLOCK THE TRIGGER LINKAGE, AND THEREBY PREVENT THE
TRIGGER FROM FIRING THE PISTOL WHEN THE MAGAZINE IS
REMOVED FROM THE PISTOL.
YOU MUST FULLY RELEASE THE TRIGGER AND REMOVE YOUR
FINGER FROM WITHIN THE TRIGGER GUARD WHEN THE MAGAZINE IS
REMOVED FROM THE PISTOL. FAILURE TO FULLY RELEASE THE
TRIGGER COULD RESULT IN FIRING THE PISTOL.

WARNING: AFTER INSERTING A MAGAZINE, ALWAYS TEST TO MAKE

SURE IT IS LOCKED IN PLACE BY APPLYING SOME REMOVAL
PRESSURE TO THE EXPOSED PORTION OF THE BUTT PLATE.

WARNING: IF YOUR PISTOL IS NOT EQUIPPED WITH THE MAGAZINE

DISCONNECT FEATURE YOUR PISTOL WILL FIRE WITH THE
MAGAZINE REMOVED FROM THE PISTOL.

15
FIRING
WARNING: ALWAYS KEEP THE MUZZLE POINTED IN A SAFE
DIRECTION.

WARNING: WEAR EYE AND EAR PROTECTION SPECIFIED FOR

FIREARM USE EVERY TIME YOU DISCHARGE YOUR FIREARM. MAKE
SURE OTHERS IN THE VICINITY OF WHERE YOU WILL BE SHOOTING
DO SO AS WELL.

WARNING: “STAGING” THE TRIGGER VIOLATES A BASIC RULE OF

FIREARM SAFETY WHICH WARNS YOU TO KEEP YOUR FINGER OUT
OF THE TRIGGER GUARD UNTIL YOU HAVE MADE THE COMMITMENT
TO FIRE. “STAGING” CREATES A SERIOUS RISK OF PERSONAL
INJURY OR DEATH SINCE IT MAY LEAD TO AN UNINTENTIONAL
DISCHARGE.

! It has come to our attention that some users of WALTHER handguns may
stage the trigger in anticipation of firing a shot. Staging is the act of pulling
the trigger rearward toward – stopping just short of – the point where the
handgun fires. Such manipulation of the trigger can reduce the user’s control
of the handgun and can result in an unintentional discharge. Furthermore if
the user decides not to fire, release of the trigger from a position close to the
firing point in the staging process could result in an unintentional discharge.
! Keep the muzzle pointed in a safe direction and your finger outside the
trigger guard until you are ready to fire. Each shot will be fired in the striker
fire action mode. While holding the grip firmly, pull the trigger fully to the rear.
As the trigger is drawn fully to the rear, the striker assembly is released,
striking the cartridge primer. Upon firing, the slide moves rearward thereby
extracting and ejecting the spent cartridge case. The slide then returns
forward feeding the next cartridge from the magazine into the barrel
chamber.
! Perform the inspection procedure outlined in the “Inspecting Your Pistol”
section of this manual which begins on page 12 to determine if your pistol is
equipped with a magazine disconnect feature.
WARNING: PISTOLS WITH A MAGAZINE DISCONNECT FEATURE WILL
BLOCK THE TRIGGER LINKAGE, AND THEREBY PREVENT THE
TRIGGER FROM FIRING THE PISTOL WHEN THE MAGAZINE IS
REMOVED FROM THE PISTOL. YOU MUST FULLY RELEASE THE
TRIGGER AND REMOVE YOUR FINGER FROM WITHIN THE TRIGGER
GUARD WHEN THE MAGAZINE IS REMOVED FROM THE PISTOL.
FAILURE TO FULLY RELEASE THE TRIGGER COULD RESULT IN FIRING
THE PISTOL.

WARNING: AFTER INSERTING A MAGAZINE, ALWAYS TEST TO MAKE

SURE IT IS LOCKED IN PLACE BY APPLYING SOME REMOVAL
PRESSURE TO THE EXPOSED PORTION OF THE BUTT PLATE.

16
FIRING CONT’D.
! After firing you must allow the trigger to move forward fully before you can
fire another shot. Failure to do so will prevent the lockwork from fully cycling
and will prevent your being able to fire the next shot. Keep your finger off the
trigger and outside the trigger guard until you are ready to fire again.
This sequence can be repeated until the last round has been fired, at which
time the magazine follower exerts upward pressure on the slide stop causing
it to engage the slide and to hold it in the “open” position.

WARNING: UPON FIRING THE PISTOL OR RELEASING THE SLIDE

FROM THE SLIDE STOP, THE SLIDE MOVES REARWARD OR
FORWARD WITH SIGNIFICANT FORCE AND SPEED. TO AVOID INJURY,
BE SURE NO PART OF YOUR BODY IS IN THE PATH OF THE SLIDE’S
TRAVEL.

CLEARING MISFIRES
WARNING: IF YOUR FIREARM GIVES ANY INDICATION THAT IT IS NOT
PERFORMING PROPERLY OR THE OPERATION OF YOUR FIREARM
HAS CHANGED “THE WAY IT FEELS OR SOUNDS”, STOP FIRING. MAKE
SURE THE FIREARM IS POINTED IN A SAFE DIRECTION, UNLOAD THE
FIREARM AND HAVE IT INSPECTED AND TEST- FIRED BY A GUNSMITH
QUALIFIED TO PERFORM SERVICE ON WALTHER FIREARMS.

! If a cartridge fails to fire, wait ten seconds while keeping the muzzle pointed
in a safe direction.
! Keep your finger off the trigger and out of the trigger guard.
! Remove the magazine.
! Grasp the serrated sides of the slide from the rear and briskly pull the slide
fully rearward to eject the misfired round. Do not obstruct the ejection port,
and do not attempt to catch the round by placing your hand over the ejection
port. Also remember that any time you release the slide while a magazine
containing cartridges is in the pistol, you will have reloaded the chamber.
! In order to lock the slide in the open position, allow the slide to move slightly
forward from the rearmost position while pressing upward on the slide stop.
You are now able to safely check the barrel chamber and bore visually for
any obstructions. You must be certain there are no cartridges in the chamber
or obstructions in the barrel.

17
UNLOADING
WARNING: IF YOUR PISTOL IS EQUIPPED WITH THE MAGAZINE
DISCONNECT FEATURE YOUR PISTOL WILL BLOCK THE TRIGGER
LINKAGE, AND THEREBY PREVENT THE TRIGGER FROM FIRING THE
PISTOL WHEN THE MAGAZINE IS REMOVED FROM THE PISTOL.
YOU MUST FULLY RELEASE THE TRIGGER AND REMOVE YOUR
FINGER FROM WITHIN THE TRIGGER GUARD WHEN THE MAGAZINE IS
REMOVED FROM THE PISTOL. FAILURE TO FULLY RELEASE THE
TRIGGER COULD RESULT IN FIRING THE PISTOL. AFTER INSERTING A
MAGAZINE, ALWAYS TEST TO MAKE SURE IT IS LOCKED IN PLACE BY
APPLYING SOME REMOVAL PRESSURE TO THE EXPOSED PORTION
OF THE BUTT PLATE.

WARNING: IF YOUR PISTOL IS NOT EQUIPPED WITH THE MAGAZINE

DISCONNECT FEATURE YOUR PISTOL WILL FIRE WITH THE
MAGAZINE REMOVED FROM THE PISTOL.

! Point the muzzle in a safe direction. Make sure your finger is off the trigger
and out of the trigger guard. Depress the
magazine release and remove the magazine.
! Keep the muzzle still pointed in a safe direction,
and keep your finger off the trigger and outside
the trigger guard. Grasp the serrated sides of the
slide from the rear with the thumb and fingers,
(Figure 18.1) and briskly draw the slide fully
rearward in order to extract any cartridge from the
barrel chamber and clear it from the pistol. FIGURE 18.1
! Lock the slide in the open position by allowing the
slide to move slightly forward from the rearmost position while pressing
upward on the slide stop.
! Do not obstruct the ejection port because doing so can interfere with ejection
of a cartridge. Visually check the barrel chamber to be sure it is empty.
! Look into the chamber and down through the magazine well. Verify that no
ammunition remains in the pistol.
! Unload the magazine by holding it with the bullet end of the cartridge pointing
away from you and pressing each cartridge forward and out of the magazine.

18
FIELD STRIPPING DISASSEMBLY
WARNING: ALWAYS KEEP THE BARREL POINTED IN A SAFE
DIRECTION.

WARNING: ALWAYS FOLLOW THE FIELD STRIPPING INSTRUCTIONS

EXACTLY. NEVER DO ANYTHING BEYOND WHAT YOU ARE
SPECIFICALLY INSTRUCTED TO DO IN THIS MANUAL. NEVER ALTER
OR MODIFY THE PARTS IN YOUR PISTOL.

WARNING: WEAR SAFETY GLASSES EVERY TIME YOU ASSEMBLE OR

DISASSEMBLE YOUR FIREARM.

! Point the pistol in a safe direction. Make sure

your finger is off the trigger and out of the
trigger guard. Depress the magazine release,
and remove the magazine. (Figure 19.1)
With the barrel still pointing in a safe direction,
and with your finger off the trigger and outside
the trigger guard, grasp the serrated sides of
the slide from the rear with the thumb and
fingers (Figure 19.2) while holding the firearm
in an upright position, and briskly draw the
slide fully rearward in order to extract any FIGURE 19.1
cartridge from the barrel chamber and clear it
from the pistol.
! Make certain that the chamber is clear. (Figure 19.3)

FIGURE 19.2 FIGURE 19.3

19
FIELD STRIPPING DISASSEMBLY CONT’D.
! Press the latch at the bottom of the QuickSafeTMbackstrap (Figure 20.1) and
remove the backstrap from the grip. (Figure 20.2)

FIGURE 20.1 FIGURE 20.2

! Hold the take down lever on both sides and slide it downwards. (Figure 20.3)
! Grasp the slide from the top, in front of the rear sight, and remove the slide by
pulling it forward while being careful to retain the recoil spring and guide rod
assembly. (Figure 20.4)
! Remove the recoil spring and barrel from the bottom of the slide. (Figure 20.5)
! Figure 20.6 shows the parts you will have after field stripping.

FIGURE 20.3 FIGURE 20.4

FIGURE 20.5 FIGURE 20.6

20
FIELD STRIPPING DISASSEMBLY CONT’D.
WARNING: DO NOT ALTER, MODIFY OR REPLACE ANY OF THE PARTS
OF YOUR FIREARM UNLESS THIS WORK IS PERFORMED BY A
QUALIFIED GUNSMITH USING GENUINE WALTHER PARTS. IF YOU DO
OTHERWISE, IMPROPER FUNCTIONING MAY OCCUR AND SERIOUS
INJURY MAY RESULT.

WARNING: NEVER DISASSEMBLE YOUR HANDGUN BEYOND THE

FIELD STRIPPING PROCESS OUTLINED IN THIS MANUAL. NEVER
MANIPULATE ANY INTERNAL COMPONENTS BEYOND WHAT YOU ARE
SPECIFICALLY INSTRUCTED TO DO IN THIS MANUAL SINCE THIS MAY
AFFECT THE RELIABILITY, FUNCTIONING AND SAFETY OF YOUR
HANDGUN.

FIELD STRIPPING ASSEMBLY

WARNING: ALWAYS FOLLOW THE FIELD STRIPPING INSTRUCTIONS
EXACTLY. NEVER DO ANYTHING BEYOND WHAT YOU ARE
SPECIFICALLY INSTRUCTED TO DO IN THIS MANUAL. NEVER ALTER
OR MODIFY THE PARTS IN YOUR PISTOL.

WARNING: WEAR SAFETY GLASSES EVERY TIME YOU ASSEMBLE OR

DISASSEMBLE YOUR FIREARM.

! With the bottom of the slide turned

upwards, replace the barrel in the
slide so the muzzle is flush with the
front end of the slide and the barrel
lug is turned up away from the
ejection port. (Figure 21.1)

FIGURE 21.1

21
FIELD STRIPPING ASSEMBLY CONT’D.
! Insert the larger end of the recoil spring guide assembly into the slide guide
housing (muzzle end) and the rear of the spring into the assembly notch of
the barrel lug. (Figure 22.4)
Make sure it is properly centered. (See Figures 22.1-22.4)

FIGURE 22.1: Spring misaligned FIGURE 22.2: Spring correctly aligned

FIGURE 22.3: Spring not seated FIGURE 22.4: Spring correctly seated

! Holding the slide and recoil spring guide

firmly in one hand, place the rear of the
slide onto the front frame rails. (Figure 22.5)
Continue moving the slide onto the frame
until the slide is fully rearward.
Now allow it to move forward to the closed
position.

FIGURE 22.5
! Align index markings and push the
backstrap up and towards the grip in a 1
continuous motion. (Figure 22.6)
The backstrap installs easily, be 4 Index
careful not to apply excessive force. Markings
2
3

22 FIGURE 22.6
REPLACING THE BACKSTRAP
The PPS features WALTHER’s QuickSafeTM technology. By removing the backstrap
from the frame, the striker assembly is de-cocked and the pistol is incapable of firing.

WARNING: MAKE SURE THE HANDGUN IS UNLOADED BEFORE

CHANGING THE BACKSTRAP.

! If the backstrap currently on your pistol does not fit your hand comfortably,
you can install one of a different size and shape. Backstrap sizes S and L are
included. Press the latch at the bottom of the backstrap (Figure 23.1) and
remove the backstrap from the grip. (Figure 23.2) Take the current backstrap
off the handgun and replace it with the appropriate insert.
! Align index markings and push the backstrap up and towards the grip in a
continuous motion. (Figure 23.3) The backstrap installs easily, be careful not
to apply excessive force. (Figure 23.4)
! Caution: Some solvents may cause damage to the backstraps. See the
“Cleaning and Maintenance” section of this manual for more information.

FIGURE 23.1 FIGURE 23.2

4 Index
Markings
2
3

FIGURE 23.3 FIGURE 23.4

23
MAGAZINE
With three magazines of different length available for each caliber, the PPS frame
length can be adjusted to fit any hand size.

MAGAZINE CAPACITY
The capacity of the magazine depends on the size of the magazine floorplate. Three
different magazine capacities are available.

Magazine capacity:
Caliber
9mm Luger .40 S&W
Small Magazine Floorplate 6 5
Medium Magazine Floorplate 7 6
Large Magazine Floorplate 8 7
Note: The capacity of the magazine is determined by the magazine floorplate.
The magazine tube and the number of witness holes is the same for any
magazine size.

FIGURE 24.1: Small, medium, and large

magazine floorplate (from left to right)

WARNING: WEAR SAFETY GLASSES EVERY TIME YOU ASSEMBLE OR

DISASSEMBLE YOUR MAGAZINE.
WARNING: THE MAGAZINE SPRING IS UNDER PRESSURE.
CONTROL THE SPRING AND FOLLOWER SO THAT THEY DO NOT FLY
OUT AND CAUSE INJURY.

24
MAGAZINE CONT’D.
DISASSEMBLY
1. Using a drift punch, depress the floorplate catch through the hole in the
floorplate.
For magazines with an extension: Align the legs of the floorplate parallel to the
rear wall of the magazine housing. (Figure 25.1)
2. Slide the floorplate forward off of the tube while continuing to depress the
floorplate catch.
3. Remove the floorplate catch and spring out through the bottom of the tube.
4. Turn the tube right side up and remove the follower through the bottom of the
tube. (Figure 25.2)

FIGURE 25.1 FIGURE 25.2

ASSEMBLY
1. Install the magazine spring and follower and the floorplate catch in reverse
order into the tube in exactly the same orientation as they were in when they
were first removed during disassembly.
2. While holding the floorplate catch in the tube, slide the floorplate onto the tube
so that the round projection of the floorplate catch engages the hole in the
floorplate. There will be an audible “snap” heard. (Figure 25.3)
For magazines with an extension: While holding the floorplate catch in the
tube and the legs of the floorplate parallel to the rear wall of the magazine
housing, slide the floorplate onto the tube. (Figure 25.4)

FIGURE 25.3 FIGURE 25.4

25
SIGHT ADJUSTMENT
WINDAGE
The rear sight is adjustable for windage only. To adjust, move the rear sight in the
direction you wish the group to move on the target. For example, if the group should
move to the right, move the rear sight to the right. Use a brass or plastic drift or
punch to prevent marring the rear sight. If the rear sight has a set screw, loosen the
set screw prior to moving the rear sight. Tighten the set screw after the sight has
been adjusted to the desired position.

ELEVATION
Using front sights of varying height corrects the elevation of the group.
If the shots group low, use a lower front sight, for high grouping a higher one. The
front sights are numbered. The higher the number, the higher the front sight. Each
stage results in a correction of the impact by about 2 inch (5 cm) at 25 yards (25 m)
range. Optional front sights are available.
To change the front sight, remove the slide from the frame as described in “Field
Stripping Disassembly”, and remove recoil spring and barrel.
Remove the front sight screw using a screw driver and press the front sight out.
Assembly is in reverse order. Remember to make sure the screw and the thread
inside the steel front sight are free of oil or grease. The thread of the front sight screw
is to be secured using an industrial adhesive (for example Loctite 648).

CLEANING, LUBRICATION, AND MAINTENANCE

WARNING: ENSURE YOUR FIREARM IS UNLOADED BEFORE
BEGINNING TO CLEAN IT (SEE “INSPECTING YOUR PISTOL” SECTION).
ALWAYS FOLLOW THE RULES OF SAFE GUN HANDLING.
Before using your firearm for the first time, it should be cleaned.
Your firearm has been treated with either a preservative or oil to protect it against
corrosion. Before using it, all excess oil should be wiped from the bore, chamber, and
exposed areas using a clean swab or patch. A light coat of high quality gun oil should
be applied to the outside surfaces and mechanism.
Care should be taken not to oil the mechanism to the extent where oil will be dripping
or running down the handgun. Dirt and residue will be trapped if too much oil is
present.
After each use of your firearm, it should be cleaned by brushing the barrel bore and
chamber with a good powder-removing solvent and bore brush. Wipe the areas clean
with patches or a swab. Using a small brush dipped in solvent, remove all deposits
from around the breech of the barrel, chamber, extractor and adjacent areas which
have been subjected to the action of powder or primer residue. Remove any residue
on the frame with light brushing and a solvent. After cleaning the entire gun, use a
cloth to apply a light film of high quality gun oil to all external metal surfaces and wipe
clean.
After sustained firing, it may be more effective to clean the components after the
pistol has been field stripped. Remove all firing residue from the exterior of the barrel,
the bottom of the slide and the top of the frame using a nylon or soft brass brush.
Remove lead and firing residue from the interior of the barrel using a brass brush.

26
CLEANING, LUBRICATION, AND MAINTENANCE CONT’D.
CAUTION:
Always follow the instructions provided with your gun cleaner and gun lubricant.

CAUTION:
Some cleaners can cause damage to your handguns. You should avoid prolonged
solvent immersion and prolonged ultrasonic cleaning of your firearm. Choice of
solvent should be restricted to those products specifically developed for firearms
maintenance. Damage to a firearm’s finish may occur if these cautions are ignored.
Ammoniated solvents or other strong alkaline solvents, should not be used on any
WALTHER firearm. As a rule of thumb, if you would be comfortable applying the
solvent of your choice to the finish of your automobile, it will probably be safe for use
on your firearm.
After the cleaning, there may be some residue in the barrel that works out and
becomes apparent within 24-48 hours. This can be removed with a bristle brush and
a light reapplication of powder removing solvent after which the oil film should be re-
established on all surfaces.
Cleaning is essential to ensure the proper functioning of your handgun.
Your firearm is a precision instrument. To ensure reliable function it is necessary to
follow a routine maintenance procedure.
After firing your handgun, be sure to unload it following the procedure outlined in the
section entitled “Inspecting Your Pistol” before performing any cleaning or
maintenance procedure.
WARNING: NEVER MANIPULATE, ADJUST OR CHANGE ANY OF THE
INTERNAL COMPONENTS OF YOUR FIREARM UNLESS SPECIFICALLY
DIRECTED TO DO SO IN THIS MANUAL. IMPROPER MANIPULATION OF
ANY INTERNAL COMPONENT MAY AFFECT THE SAFETY AND
RELIABILITY OF YOUR FIREARM AND MAY CAUSE SERIOUS INJURY
OR DEATH.

WARNING: ANY MAINTENANCE OR SERVICE NOT SPECIFIED IN THIS

MANUAL MUST BE PERFORMED BY A QUALIFIED GUNSMITH USING
GENUINE WALTHER PARTS. IF YOU DO OTHERWISE, IMPROPER
FUNCTIONING OF YOUR FIREARM MAY OCCUR AND SERIOUS INJURY
OR DEATH MAY RESULT.
If your firearm will be used or stored in a cold climate, be sure to use an oil of an
appropriate type so that it will not congeal in the cold temperatures.

27
CLEANING, LUBRICATION, AND MAINTENANCE CONT’D.
LUBRICATION
There are six (6) lubrication points where a single drop of high-quality firearms
lubricant should be applied. (Figures 28.1-28.2) This will ensure proper lubrication.
Care should be taken not to overlubricate. Excess lubricant can collect large
quantities of unburned powder and carbon residue, which could interfere with proper
functioning of the pistol.

1 5
2 3 4 6

FIGURE 28.1 FIGURE 28.2

MAINTENANCE BEFORE STORAGE

When storing, do not encase your firearm in anything that will attract or hold
moisture, for example, leather or heavy cloth.
Also, do not store guns with a plug inserted in the barrel for this can be a contributing
factor to moisture accumulation. If your firearm is to be stored for an extended period,
the bore, chambers and internal working mechanism should be oiled with a high
quality lubricating oil or preservative intended for firearms.

The external working mechanisms, slide, barrel and magazine should be coated with
an anti-rust oil. Before using your firearm again, be sure to clean it. Every time you
clean your firearm, check it for signs of wear. If wear is noted, do not use the firearm.
Return it to WALTHER for service or have it checked by a qualified gunsmith.

WARRANTY
Within the first year after the date of purchase, WALTHER will repair or replace your
defective weapon free of charge provided the defect was not caused by your misuse
or negligence.
WALTHER handguns are warrantied to be free from defects in material and
workmanship. Any such defects of which WALTHER receives written notice within
one year from the date of purchase by the original owner, will be remedied by
WALTHER without charge within a reasonable time after such notification and
delivery of the handgun as provided below.
Warranty claims (in writing) and the handgun concerned should be delivered to
WALTHER’s Warranty Service in its original case or in a similarly secure container.
In addition, a copy of the bill of sale in the owner’s name, or a copy of
ATF Form 4473 indicating date of purchase must be included.

28
WARRANTY CONT’D.
Warranty claims should state the model and serial number of the handgun concerned
and the description of the difficulty experienced. It is recommended that shipments
be insured by the owner, since WALTHER will accept no responsibility for loss or
damage in transit. Transportation and insurance charges for return to owner will be
paid by WALTHER if the claim is covered by the warranty.
THIS WARRANTY IS EXCLUSIVE AND IS GIVEN IN LIEU OF ANY AND ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED.
NO IMPLIED WARRANTIES OR MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE ARE GIVEN AND ANY AND ALL LIABILITY FOR
BREACH OF ANY IMPLIED WARRANTY OR WARRANTY CREATED BY LAW IS
DISCLAIMED.
UNDER NO CIRCUMSTANCES SHALL WALTHER BE RESPONSIBLE FOR
INCIDENTAL OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ECONOMIC
LOSS, INJURY, DEATH OR PROPERTY DAMAGE, WHETHER AS A RESULT OF
BREACH OF THIS WARRANTY, NEGLIGENCE OR OTHERWISE.
Some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you in whole or in
part.
WALTHER will not be responsible for:
! Defects or malfunctions resulting from careless handling, unauthorized
adjustments or modifications made or attempted by anyone other than a
qualified gunsmith following WALTHER authorized procedures, or
disassembly beyond the Field Stripping instructions in this manual.
! Use of defective or improper ammunition, corrosion, neglect, abuse, ordinary
wear and tear, or unreasonable use.
! Criminal misuse, negligence, resale, use under the influence of drugs or
alcohol.
WALTHER reserves the right to determine what constitutes ordinary wear and tear.
This warranty gives you specific legal rights. You may also have other rights that vary
from state to state.
Note: All liability is excluded in the event that the instructions in this manual are not
observed.

CONTACT & SHIPPING

For Owners Within The United States
Walther America
Sales + Warranty Service
2100 Roosevelt Ave.
Springfield, MA 01104
Phone: 1-800-372-6454
Fax: 413-747-3317
E-mail: customerservice@waltheramerica.com

29
CONTACT & SHIPPING CONT’D.
! Call or e-mail the Customer Service Dept. for authorization and shipping
instructions.
! Ensure that the firearm is unloaded.
! DO NOT SHIP ANY AMMUNITION.
! Enclose a letter which includes your full name and address (no P.O. Boxes,
please), daytime telephone number, e-mail address, the serial number of the
firearm, and details of the problem experienced (stating the brand and type of
ammunition used when the problem occurred) or work desired.
! Record the serial number before shipping, in case you wish to check on the
repair status of your firearm.
! Please remove all custom parts and accessories, such as stocks, special
sights, or holsters from your firearm before returning.
! Place the handgun in its original case or in a similarly secure container and
pack securely.
! When returning a pistol, please include all magazines ensuring they are
unloaded; they are important to the proper function of the handgun.
! The package must NOT bear any markings which indicate the identity of the
contents.
! It is most important that you comply with federal, state, and local laws and
regulations. The following guidelines are meant to help, but you must seek
assistance from the appropriate authorities if necessary.
! Do not attempt to ship a handgun via US Postal Service; only federally
licensed dealers may ship a firearm by US Postal Service.
! If your firearm must be replaced, it may be necessary to ship the replacement
to a dealer rather than directly to you. You will be requested to furnish a
signed FFL (Federal Firearms License) from your dealer in such an instance.
! Warranty repair work will begin upon receipt and examination of the firearm.
In the case of repairs or work not covered by the warranty, a quotation
covering the cost of the work plus round trip transportation charges will be
sent to you. Repairs or modification will begin upon receipt of payment.
WARNING: YOU MAY PURCHASE ACCESSORIES FOR YOUR WALTHER
FIREARM. YOU MUST HAVE SOME OF THESE PARTS INSTALLED BY A
GUNSMITH QUALIFIED TO PERFORM SERVICE ON WALTHER PISTOLS.
YOU MUST NEVER ATTEMPT TO MODIFY YOUR FIREARM OR INSTALL
REPLACEMENT PARTS IN YOUR FIREARM. ALWAYS USE A QUALIFIED
WALTHER GUNSMITH EVEN IF THE REPAIR SEEMS TO BE SIMPLE.

ACCESSORIES
Accessories for your WALTHER firearm are available from your local WALTHER
Stocking Dealer, or directly from Walther America.
Contact the Customer Service Department at 1-800-372-6454 or
www.waltheramerica.com for information about these services.

30
Note:
This handgun is not equipped with a
device that fully blocks use by
unauthorized users. More than
200,000 firearms like this one are
stolen from their owners every year
in the United States. In addition,
there are more than a thousand
suicides each year by younger
children and teenagers who get
access to firearms. Hundreds more
die from accidental discharge. It is
likely that many more children
sustain serious wounds or inflict
such wounds accidentally on others.
In order to limit the chance of such
misuse, it is imperative that you
keep this weapon locked in a
secure place and take other steps
necessary to limit the possibility of
theft or accident. Failure to take
reasonable preventative steps may
result in innocent lives being lost,
and in some circumstances may
result in your liability for these
deaths.

31
 Rev. c
Subject to change without notice
273 35 44.CW.02-09.5,0.

Walther America
2100 Roosevelt Avenue • Springfield, MA 01104
1-800-372-6454 • Fax: 413-747-3317
www.waltheramerica.com