N68C-S Ucc

N68C-GS UCC /
N68C-S UCC
User Manual
Version 1.2
Published May 2010
Copyright©2010 ASRock INC. All rights reserved.
1
Copyright Notice:
No part of this manual may be reproduced, transcribed, transmitted, or translated in
any language, in any form or by any means, except duplication of documentation by
the purchaser for backup purpose, without written consent of ASRock Inc.
Products and corporate names appearing in this manual may or may not be regis-
tered trademarks or copyrights of their respective companies, and are used only for
identification or explanation and to the owners’ benefit, without intent to infringe.
Disclaimer:
Specifications and information contained in this manual are furnished for informa-
tional use only and subject to change without notice, and should not be constructed
as a commitment by ASRock. ASRock assumes no responsibility for any errors or
omissions that may appear in this manual.
With respect to the contents of this manual, ASRock does not provide warranty of
any kind, either expressed or implied, including but not limited to the implied warran-
ties or conditions of merchantability or fitness for a particular purpose.
In no event shall ASRock, its directors, officers, employees, or agents be liable for
any indirect, special, incidental, or consequential damages (including damages for
loss of profits, loss of business, loss of data, interruption of business and the like),
even if ASRock has been advised of the possibility of such damages arising from any
defect or error in the manual or product.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
CALIFORNIA, USA ONLY

The Lithium battery adopted on this motherboard contains Perchlorate, a toxic
substance controlled in Perchlorate Best Management Practices (BMP) regulations
passed by the California Legislature. When you discard the Lithium battery in
California, USA, please follow the related regulations in advance.
“Perchlorate Material-special handling may apply, see
www.dtsc.ca.gov/hazardouswaste/perchlorate”
ASRock Website: http://www.asrock.com
2
Contents
1 . Introduction ........................................................... 5
1.1 Package Contents ..................................................................... 5
1.2 Specifications ............................................................................ 6
1.3 Motherboard Layout (N68C-GS UCC / N68C-S UCC) .............. 11
1.4 I/O Panel (N68C-GS UCC) ......................................................... 12
1.5 I/O Panel (N68C-S UCC) ........................................................... 13
2 . Installation .............................................................. 14
Pre-installation Precautions ............................................................... 14
2.1 CPU Installation ......................................................................... 15
2.2 Installation of CPU Fan and Heatsink ....................................... 15
2.3 Installation of Memory Modules (DIMM) .................................... 16
2.4 Expansion Slots (PCI and PCI Express Slots) .................................. 18
2.5 Easy Multi Monitor Feature ........................................................ 19
2.6 Jumpers Setup .......................................................................... 20
2.7 Onboard Headers and Connectors .......................................... 21
2.8 SATAII Hard Disk Setup Guide .................................................. 25
2.9 Serial ATA (SATA) / Serial ATAII (SATAII) Hard Disks
Installation ................................................................................. 26
2.10 Hot Plug and Hot Swap Functions for SATA / SATAII HDDs .... 26
2.11 SATA / SATAII HDD Hot Plug Feature and Operation Guide ..... 27
2.12 Driver Installation Guide ............................................................ 29
2.13 Installing Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit / XP /
XP 64-bit Without RAID Functions ............................................ 29
2.14 Installing Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit / XP /
XP 64-bit With RAID Functions ................................................. 29
2.14.1 Installing Windows® XP / XP 64-bit With RAID
Functions ...................................................................... 29
2.14.2 Installing Windows® 7 / 7 64-bit / VistaTM /
VistaTM 64-bit With RAID Functions .............................. 30
2.15 Untied Overclocking Technology .............................................. 31
3 . BIOS SSETUP
ETUP UTILITY ................................................... 32
3.1 Introduction ............................................................................... 33
3.1.1 BIOS Menu Bar ............................................................... 33
3.1.2 Navigation Keys ............................................................. 34
3.2 Main Screen .............................................................................. 34
3.3 OC Tweaker Screen ................................................................. 35
3.4 Advanced Screen .................................................................... 42
3.4.1 CPU Configuration .......................................................... 43
3.4.2 Chipset Configuration ..................................................... 44
3.4.3 ACPI Configuration ......................................................... 45
3
3.4.4 Storage Configuration .................................................... 47
3.4.5 PCIPnP Configuration ...................................................... 49
3.4.6 Floppy Configuration ...................................................... 50
3.4.7 Super IO Configuration ................................................... 50
3.4.8 USB Configuration .......................................................... 52
3.5 Hardware Health Event Monitoring Screen ............................. 53
3.6 Boot Screen .............................................................................. 54
3.6.1 Boot Settings Configuration ........................................... 54
3.7 Security Screen ........................................................................ 55
3.8 Exit Screen ............................................................................... 56
4 . Software Support ................................................... 57
4.1 Install Operating System ........................................................... 57
4.2 Support CD Information ............................................................. 57
4.2.1 Running Support CD ....................................................... 57
4.2.2 Drivers Menu .................................................................. 57
4.2.3 Utilities Menu ................................................................... 57
4.2.4 Contact Information ........................................................ 57
4
1. Introduction
Thank you for purchasing ASRock N68C-GS UCC / N68C-S UCC motherboard, a
reliable motherboard produced under ASRock’s consistently stringent quality control.
It delivers excellent performance with robust design conforming to ASRock’s com-
mitment to quality and endurance.
In this manual, chapter 1 and 2 contain introduction of the motherboard and step-by-step
guide to the hardware installation. Chapter 3 and 4 contain the configuration guide to
BIOS setup and information of the Support CD.
Because the motherboard specifications and the BIOS software might be

updated, the content of this manual will be subject to change without
notice. In case any modifications of this manual occur, the updated
version will be available on ASRock website without further notice. You
may find the latest VGA cards and CPU support lists on ASRock website
as well. ASRock website http://www.asrock.com
If you require technical support related to this motherboard, please visit
our website for specific information about the model you are using.
www.asrock.com/support/index.asp
1.1 P ack age Contents

ackage
One ASRock N68C-GS UCC / N68C-S UCC Motherboard
(Micro ATX Form Factor: 9.6-in x 8.2-in, 24.4 cm x 20.8 cm)
One ASRock N68C-GS UCC / N68C-S UCC Quick Installation Guide
One ASRock N68C-GS UCC / N68C-S UCC Support CD
Two Serial ATA (SATA) Data Cables (Optional)
One I/O Panel Shield
5
1.2 Specifications
Platform - Micro ATX Form Factor: 9.6-in x 8.2-in, 24.4 cm x 20.8 cm

CPU - Support for Socket AM2+ / AM2 processors: AMD PhenomTM
FX / Phenom / Athlon 64 FX / Athlon 64 X2 Dual-Core / Athlon
X2 Dual-Core / Athlon 64 / Sempron processor
(see CAUTION 1)
- Support for AM3 processors: AMD PhenomTM II X6 / X4 / X3 /
X2 / Athlon II X4 / X3 / X2 / Sempron processors
- Six-Core CPU Ready
- Supports UCC feature (Unlock CPU Core) (see CAUTION 2)
- Supports AMD’s Cool ‘n’ QuietTM Technology
- FSB 1000 MHz (2.0 GT/s)
- Supports Untied Overclocking Technology (see CAUTION 3)
- Supports Hyper-Transport Technology
Chipset - NVIDIA® GeForce 7025 / nForce 630a
Memory - Dual Channel DDR3/DDR2 Memory Technology
(see CAUTION 4)
- 2 x DDR3 DIMM slots
- Support DDR3 1600/1333/1066/800 non-ECC, un-buffered
memory (see CAUTION 5)
- Max. capacity of system memory: 8GB (see CAUTION 6)
- 2 x DDR2 DIMM slots
- Support DDR2 1066/800/667/533 non-ECC, un-buffered
memory (see CAUTION 7)
- Max. capacity of system memory: 8GB (see CAUTION 6)
Expansion Slot - 1 x PCI Express x16 slot
- 1 x PCI Express x1 slot
- 2 x PCI slots
Graphics - Integrated NVIDIA® GeForce 7025 graphics
- DX9.0 VGA, Pixel Shader 3.0
- Max. shared memory 256MB (see CAUTION 8)
- Supports D-Sub with max. resolution up to 1920x1440
@ 60Hz
Audio - 5.1 CH HD Audio (VIA® VT1705 Audio Codec)
LAN - N68C-GS UCC
Realtek Giga PHY RTL8211CL, speed 10/100/1000 Mb/s
- N68C-S UCC
Realtek PHY RTL8201EL, speed 10/100 Mb/s
- Supports Wake-On-LAN
6
Rear Panel I/O I/O Panel
- 1 x PS/2 Mouse Port
- 1 x PS/2 Keyboard Port
- 1 x Serial Port: COM1
- 1 x VGA Port
- 4 x Ready-to-Use USB 2.0 Ports
- 1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED LED)
- HD Audio Jack: Line in / Front Speaker / Microphone
Connector - 4 x Serial ATAII 3.0Gb/s connectors, support RAID (RAID 0,
RAID 1, RAID 0+1, RAID 5, JBOD), NCQ and “Hot Plug”
functions (see CAUTION 9)
- 1 x ATA133 IDE connector (supports 2 x IDE devices)
- 1 x Floppy connector
- 1 x Print Port header
- CPU/Chassis/Power FAN connector
- 24 pin ATX power connector
- 4 pin 12V power connector
- CD in header
- Front panel audio header
- 3 x USB 2.0 headers (support 6 USB 2.0 ports)
(see CAUTION 10)
BIOS Feature - 8Mb AMI Legal BIOS
- Supports “Plug and Play”
- ACPI 1.1 Compliance Wake Up Events
- Supports jumperfree
- SMBIOS 2.3.1 Support
- CPU, VCCM, NB Voltage Multi-adjustment
Support CD - Drivers, Utilities, AntiVirus Software (Trial Version), ASRock
Software Suite (CyberLink DVD Suite and Creative Sound
Blaster X-Fi MB) (OEM and Trial Version)
Unique Feature - ASRock OC Tuner (see CAUTION 11)
- Intelligent Energy Saver (see CAUTION 12)
- Instant Boot
- ASRock Instant Flash (see CAUTION 13)
- ASRock OC DNA (see CAUTION 14)
- Hybrid Booster:
- CPU Frequency Stepless Control (see CAUTION 15)
- ASRock U-COP (see CAUTION 16)
- Boot Failure Guard (B.F.G.)
- ASRock AM2 Boost: ASRock Patented Technology to boost
memory performance up to 12.5% (see CAUTION 17)
7
Hardware - CPU Temperature Sensing
Monitor - Chassis Temperature Sensing
- CPU/Chassis/Power Fan Tachometer
- CPU Quiet Fan
- Voltage Monitoring: +12V, +5V, +3.3V, Vcore
OS - Microsoft® Windows® 7 / 7 64-bit / Vista TM / VistaTM 64-bit /
XP / XP 64-bit compliant
Certifications - FCC, CE, WHQL
* For detailed product information, please visit our website: http://www.asrock.com
WARNING
Please realize that there is a certain risk involved with overclocking, including adjusting
the setting in the BIOS, applying Untied Overclocking Technology, or using the third-
party overclocking tools. Overclocking may affect your system stability, or even
cause damage to the components and devices of your system. It should be done at
your own risk and expense. We are not responsible for possible damage caused by
overclocking.
CAUTION!
1. This motherboard supports CPU up to 95W. Please refer to our website for
CPU support list. ASRock website http://www.asrock.com
2. UCC (Unlock CPU Core) feature simplifies AMD CPU activation. As long as
a simple switch of the BIOS option “ASrock UCC”, you can unlock the extra
CPU core to enjoy an instant performance boost. When UCC feature is
enabled, the dual-core or triple-core CPU will boost to the quad-core CPU, and
some CPU, including quad-core CPU, can also increase L3 cache size up to
6MB, which means you can enjoy the upgrade CPU performance with a better
price. Please be noted that UCC feature is supported with AM2+ / AM3 CPU
only, and in addition, not every AM2+ / AM3 CPU can support this function
because some CPU’s hidden core may be malfunctioned.
3. This motherboard supports Untied Overclocking Technology. Please read “Un-
tied Overclocking Technology” on page 31 for details.
4. This motherboard supports Dual Channel Memory Technology. Before you
implement Dual Channel Memory Technology, make sure to read the
installation guide of memory modules on page 16 for proper installation.
5. Whether 1600MHz memory speed is supported depends on the AM3 CPU
you adopt. If you want to adopt DDR3 1600 memory module on this
motherboard, please refer to the memory support list on our website for
the compatible memory modules.
ASRock website http://www.asrock.com
6. Due to the operating system limitation, the actual memory size may be
less than 4GB for the reservation for system usage under Windows® 7 /
VistaTM / XP. For Windows® OS with 64-bit CPU, there is no such limitation.
8
7. Whether 1066MHz memory speed is supported depends on the AM2+ CPU
you adopt. If you want to adopt DDR2 1066 memory module on this
motherboard, please refer to the memory support list on our website for
the compatible memory modules.
ASRock website http://www.asrock.com
8. The maximum shared memory size is defined by the chipset vendor and
is subject to change. Please check NVIDIA ® website for the latest
information.
9. Before installing SATAII hard disk to SATAII connector, please read the “SATAII
Hard Disk Setup Guide” on page 25 to adjust your SATAII hard disk drive to
SATAII mode. You can also connect SATA hard disk to SATAII connector
directly.
10. Power Management for USB 2.0 works fine under Microsoft® Windows® 7
64-bit / 7 / VistaTM 64-bit / VistaTM / XP 64-bit / XP SP1 or SP2.
11. It is a user-friendly ASRock overclocking tool which allows you to surveil
your system by hardware monitor function and overclock your hardware
devices to get the best system performance under Windows® environment.
Please visit our website for the operation procedures of ASRock OC
Tuner. ASRock website: http://www.asrock.com
12. Featuring an advanced proprietary hardware and software design,
Intelligent Energy Saver is a revolutionary technology that delivers
unparalleled power savings. The voltage regulator can reduce the
number of output phases to improve efficiency when the CPU cores are
idle. In other words, it is able to provide exceptional power saving and
improve power efficiency without sacrificing computing performance.
To use Intelligent Energy Saver function, please enable Cool ‘n’ Quiet
option in the BIOS setup in advance. Please visit our website for the
operation procedures of Intelligent Energy Saver.
ASRock website: http://www.asrock.com
13. ASRock Instant Flash is a BIOS flash utility embedded in Flash ROM.
This convenient BIOS update tool allows you to update system BIOS
without entering operating systems first like MS-DOS or Windows ®.
With this utility, you can press <F6> key during the POST or press <F2>
key to BIOS setup menu to access ASRock Instant Flash. Just launch
this tool and save the new BIOS file to your USB flash drive, floppy disk
or hard drive, then you can update your BIOS only in a few clicks without
preparing an additional floppy diskette or other complicated flash utility.
Please be noted that the USB flash drive or hard drive must use FAT32/
16/12 file system.
14. The software name itself – OC DNA literally tells you what it is capable of.
OC DNA, an exclusive utility developed by ASRock, provides a conve-
nient way for the user to record the OC settings and share with others. It
helps you to save your overclocking record under the operating system
and simplifies the complicated recording process of overclocking settings.
With OC DNA, you can save your OC settings as a profile and share with
your friends! Your friends then can load the OC profile to their own system
to get the same OC settings as yours! Please be noticed that the OC
profile can only be shared and worked on the same motherboard.
9
15. Although this motherboard offers stepless control, it is not recommended
to perform over-clocking. Frequencies other than the recommended CPU
bus frequencies may cause the instability of the system or damage the
CPU.
16. While CPU overheat is detected, the system will automatically shutdown.
Before you resume the system, please check if the CPU fan on the
motherboard functions properly and unplug the power cord, then plug it
back again. To improve heat dissipation, remember to spray thermal
grease between the CPU and the heatsink when you install the PC system.
17. This motherboard supports ASRock AM2 Boost overclocking technology. If
you enable this function in the BIOS setup, the memory performance will
improve up to 12.5%, but the effect still depends on the AM2 CPU you adopt.
Enabling this function will overclock the chipset/CPU reference clock. However,
we can not guarantee the system stability for all CPU/DRAM configurations.
If your system is unstable after AM2 Boost function is enabled, it may not be
applicative to your system. You may choose to disable this function for
keeping the stability of your system.
10
1.3 Motherboard Layout (N68C-GS UCC / N68C-S UCC)
1 2 3 4 5 6 7
20.8cm (8.2-in)
Keyboard
Mouse
PS2
PS2
1
PS2_USB_PWR1
CPU_FAN1 ATX12V1
COM1
Phenom II
Designed in Taipei
AM2+/AM3
DDR3_A1 (64 bit, 240-pin module)
DDR3_B1 (64 bit, 240-pin module)
ATXPWR1
FSB800
FSB800
DDRII_1 (64 bit, 240-pin module)
DDRII_2 (64 bit, 240-pin module)

VGA1
SOCKET AM2 8
24.4cm (9.6-in)
USB 2.0
T: USB2
B: USB3
USB 2.0
Top:
T: USB0 RJ-45
B: USB1
9
LAN DDR2 1066
MIC IN
Bottom:
LINE IN
Top:
PHY
FRONT
Center:
DDR3 1600
Dual Channel
NVIDIA
GeForce
7025 /
31
nForce IDE1
10
30 PCIE1
630a 11
SATAII_1 (PORT 0.0) SATAII_3 (PORT 1.0)
SATAII_2 (PORT 0.1) SATAII_4 (PORT 1.1)
RoHS
Super 12
I/O
PCIE2 13
Support 6-Core CPU
29 CMOS 8Mb
BIOS
14
PCI1 BATTERY
28 1
USB_PWR2
15
AUDIO
1
1
1
CODEC PCI2 CLRCMOS1

USB4_5
USB8_9
USB6_7
CD1
PWR_FAN1
FLOPPY1
LPT1
CHA_FAN1 PANEL 1
PLED PWRBTN
16
HD_AUDIO1
SPEAKER1
1 1 1 1
HDLED RESET
27 26 25 24 23 22 21 20 19 18 17
1 PS2_USB_PWR1 Jumper 16 USB 2.0 Header (USB8_9, Blue)

2 CPU Fan Connector (CPU_FAN1) 17 USB 2.0 Header (USB6_7, Blue)
3 ATX 12V Power Connector (ATX12V1) 18 USB 2.0 Header (USB4_5, Blue)
4 CPU Heatsink Retention Module 19 Chassis Speaker Header
5 AM2 940-Pin CPU Socket (SPEAKER 1, White)
6 2 x 240-pin DDR2 DIMM Slots 20 System Panel Header (PANEL1, White)
(Dual Channel: DDRII_1, DDRII_2; Yellow) 21 Chassis Fan Connector (CHA_FAN1)
7 2 x 240-pin DDR3 DIMM Slots 22 Clear CMOS Jumper (CLRCMOS1)
(Dual Channel: DDR3_A1, DDR3_B1; Blue) 23 Print Port Header (LPT1, Purple)
8 ATX Power Connector (ATXPWR1) 24 Floppy Connector (FLOPPY1)
9 Primary IDE Connector (IDE1, Blue) 25 Power Fan Connector (PWR_FAN1)
10 Primary SATAII Connector (SATAII_1 (PORT 0.0)) 26 Internal Audio Connector: CD1 (White)
11 Third SATAII Connector (SATAII_3 (PORT 1.0)) 27 Front Panel Audio Header
12 Fourth SATAII Connector (SATAII_4 (PORT 1.1)) (HD_AUDIO1, White)
13 Secondary SATAII Connector 28 PCI Slots (PCI1- 2)
(SATAII_2 (PORT 0.1)) 29 PCI Express x16 Slot (PCIE2)
14 SPI Flash Memory (8Mb) 30 PCI Express x1 Slot (PCIE1)
15 USB_PWR2 Jumper 31 NVIDIA GeForce 7025 / nForce 630a
11
1.4 I/O Panel (N68C-GS UCC)
1 2
10 9 8 7 6
1 PS/2 Mouse Port (Green) 6 USB 2.0 Ports (USB01)

2 RJ-45 Port 7 USB 2.0 Ports (USB23)
3 Line In (Light Blue) 8 VGA Port
4 Front Speaker (Lime) 9 COM Port
5 Microphone (Pink) 10 PS/2 Keyboard Port (Purple)
* There are two LED next to the LAN port. Please refer to the table below for the LAN port LED
indications.
LAN Port LED Indications
ACT/LINK SPEED
Activity/Link LED SPEED LED
LED LED
Status Description Status Description
Off No Activity Off 10Mbps connection
Blinking Data Activity Orange 100Mbps connection
Green 1Gbps connection
LAN Port
To enable Multi-Streaming function, you need to connect a front panel audio cable to the front
panel audio header. After restarting your computer, you will find “VIA HD Audio Deck” tool on
your system. Please follow below instructions according to the OS you install.
For Windows® XP / XP 64-bit OS:
Please click “VIA HD Audio Deck” icon , and click “Speaker”. Then you are allowed to
select “2 Channel” or “4 Channel”. Click “Power” to save your change.

For Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS:
Please click “VIA HD Audio Deck” icon , and click “Advanced Options” on the left side
on the bottom. In “Advanced Options” screen, select “Independent Headphone”, and click
“OK” to save your change.
12
1.5 I/O Panel (N68C-S UCC)
1 2
10 9 8 7 6
1 PS/2 Mouse Port (Green) 6 USB 2.0 Ports (USB01)

2 RJ-45 Port 7 USB 2.0 Ports (USB23)
3 Line In (Light Blue) 8 VGA Port
4 Front Speaker (Lime) 9 COM Port
5 Microphone (Pink) 10 PS/2 Keyboard Port (Purple)
* There are two LED next to the LAN port. Please refer to the table below for the LAN port LED
indications.
LAN Port LED Indications
ACT/LINK SPEED
Activity/Link LED SPEED LED
LED LED
Status Description Status Description
Off No Activity Off 10Mbps connection
Blinking Data Activity Green or 100Mbps connection
Orange
LAN Port
To enable Multi-Streaming function, you need to connect a front panel audio cable to the front
panel audio header. After restarting your computer, you will find “VIA HD Audio Deck” tool on
your system. Please follow below instructions according to the OS you install.
Please click “VIA HD Audio Deck” icon , and click “Speaker”. Then you are allowed to
select “2 Channel” or “4 Channel”. Click “Power” to save your change.

Please click “VIA HD Audio Deck” icon , and click “Advanced Options” on the left side
on the bottom. In “Advanced Options” screen, select “Independent Headphone”, and click
“OK” to save your change.
13
2. Installation
This is a Micro ATX form factor (9.6-in x 8.2-in, 24.4 cm x 20.8 cm) motherboard.
Before you install the motherboard, study the configuration of your chassis to en-
sure that the motherboard fits into it.
Pre-installation Precautions
Take note of the following precautions before you install motherboard
components or change any motherboard settings.
Before you install or remove any component, ensure that the

power is switched off or the power cord is detached from the
power supply. Failure to do so may cause severe damage to the
motherboard, peripherals, and/or components.
1. Unplug the power cord from the wall socket before touching any
component.
2. To avoid damaging the motherboard components due to static
electricity, NEVER place your motherboard directly on the carpet or
the like. Also remember to use a grounded wrist strap or touch a
safety grounded object before you handle components.
3. Hold components by the edges and do not touch the ICs.
4. Whenever you uninstall any component, place it on a grounded anti-
static pad or in the bag that comes with the component.
5. When placing screws into the screw holes to secure the motherboard
to the chassis, please do not over-tighten the screws! Doing so may
damage the motherboard.
14
2.1 CPU Installation
o
Step 1. Unlock the socket by lifting the lever up to a 90 angle.
Step 2. Position the CPU directly above the socket such that the CPU corner with
the golden triangle matches the socket corner with a small triangle.
Step 3. Carefully insert the CPU into the socket until it fits in place.
The CPU fits only in one correct orientation. DO NOT force the CPU
into the socket to avoid bending of the pins.
Step 4. When the CPU is in place, press it firmly on the socket while you push
down the socket lever to secure the CPU. The lever clicks on the side tab
to indicate that it is locked.
Lever 90° Up
CPU Golden Triangle
Socker Corner Small Triangle
STEP 1: STEP 2 / STEP 3: STEP 4:

Lift Up The Socket Lever Match The CPU Golden Triangle Push Down And Lock
To The Socket Corner Small The Socket Lever
Triangle
2.2 Installation of CPU Fan and Heatsink
After you install the CPU into this motherboard, it is necessary to install a
larger heatsink and cooling fan to dissipate heat. You also need to spray
thermal grease between the CPU and the heatsink to improve heat
dissipation. Make sure that the CPU and the heatsink are securely fas-
tened and in good contact with each other. Then connect the CPU fan to
the CPU FAN connector (CPU_FAN1, see Page 11, No. 2). For proper
installation, please kindly refer to the instruction manuals of the CPU fan
and the heatsink.
15
2.3 Installation of Memory Modules (DIMM)
This motherboard provides two 240-pin DDR2 (Double Data Rate 2) DIMM slots
and two 240-pin DDR3 (Double Data Rate 3) DIMM slots, and supports Dual
Channel Memory Technology. For dual channel configuration, you always need
to install identical (the same brand, speed, size and chip-type) DDR2/DDR3
DIMM pair in the slots of the same color. In other words, you have to install
identical DDR2 DIMM pair in Dual Channel (DDRII_1 and DDRII_2; Yellow slots;
see p.11 No.6), or identical DDR3 DIMM pair in Dual Channel (DDR3_A1 and
DDR3_B1; Blue slots; see p.11 No.7), so that Dual Channel Memory Technology
can be activated. You may refer to the Dual Channel Memory Configuration Table
below.
Dual Channel DDR2 Memory Configurations

(DS: Double Side, SS: Single Side)
DDRII_1 DDRII_2
(Yellow Slot) (Yellow Slot)
2 memory modules SS SS
2 memory modules DS DS
Dual Channel DDR3 Memory Configurations

(DS: Double Side, SS: Single Side)
DDR3_A1 DDR3_B1
(Blue Slot) (Blue Slot)
2 memory modules SS SS
2 memory modules DS DS
1. If you want to install two memory modules, for optimal compatibility

and reliability, it is recommended to install them in the slots of the
same color. In other words, install them in the set of blue slots
(DDR3_A1 and DDR3_B1), or in the set of yellow slots (DDRII_1
and DDRII_2).
2. If only one memory module is installed in the DIMM slot on this
motherboard, it is unable to activate the Dual Channel Memory
Technology.
3. It is not allowed to install a DDR3 memory module into DDR2 slot or
install a DDR2 memory module into DDR3 slot; otherwise, this
motherboard and DIMM may be damaged.
4. DDR2 and DDR3 memory modules cannot be installed on this
motherboard at the same time.
16
Installing a DIMM
Please make sure to disconnect power supply before adding or

removing DIMMs or the system components.
Step 1. Unlock a DIMM slot by pressing the retaining clips outward.

Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the break
on the slot.
notch
break
notch
break
The DIMM only fits in one correct orientation. It will cause permanent
damage to the motherboard and the DIMM if you force the DIMM into the slot
at incorrect orientation.
Step 3. Firmly insert the DIMM into the slot until the retaining clips at both ends fully
snap back in place and the DIMM is properly seated.
17
2.4 Expansion Slots (PCI and PCI Express Slots)
There are 2 PCI slots and 2 PCI Express slots on this motherboard.
PCI slots: PCI slots are used to install expansion cards that have the 32-bit PCI
interface.
PCIE slots: PCIE1 (PCIE x1 slot) is used for PCI Express cards with x1 lane width
cards, such as Gigabit LAN card, SATA2 card, etc.
PCIE2 (PCIE x16 slot) is used for PCI Express cards with x16 lane
width graphics cards.
Installing an expansion card

Step 1. Before installing the expansion card, please make sure that the power
supply is switched off or the power cord is unplugged. Please read the
documentation of the expansion card and make necessary hardware
settings for the card before you start the installation.
Step 2. Remove the bracket facing the slot that you intend to use. Keep the screws
for later use.
Step 3. Align the card connector with the slot and press firmly until the card is
completely seated on the slot.
Step 4. Fasten the card to the chassis with screws.
18
2.5 Easy Multi Monitor Feature
This motherboard supports Multi Monitor upgrade. With the internal onboard VGA and
the external add-on PCI Express VGA card, you can easily enjoy the benefits of Multi
Monitor feature. Please refer to the following steps to set up a multi monitor
environment:
1. Install the NVIDIA® PCI Express VGA card to PCIE2 (PCIE x16 slot). Please refer
to page 18 for proper expansion card installation procedures for details.
2. Connect the D-Sub monitor cable to the VGA/D-Sub port on the I/O panel of this
motherboard. Connect another D-Sub monitor cable to the VGA/D-Sub connector of
the add-on PCI Express VGA card. Connect the DVI-D monitor cable to the
VGA/DVI-D connector of the add-on PCI Express VGA card.
3. Boot your system. Press <F2> to enter BIOS setup. Enter “Share Memory”
option to adjust the memory capability to [16MB], [32MB], [64MB], [128MB] or
[256MB] to enable the function of onboard VGA/D-sub. Please make sure that
the value you select is less than the total capability of the system memory. If
you do not adjust the BIOS setup, the default value of “Share Memory”, [Auto],
will disable onboard VGA/D-Sub function when the add-on VGA card is
inserted to this motherboard.
4. Install the onboard VGA driver to your system. If you have installed the
onboard VGA driver already, there is no need to install it again.
5. Set up a multi-monitor display.
Right click the desktop, choose “Properties”, and select the “Settings” tab so
that you can adjust the parameters of the multi-monitor according to the steps
below.
A. Click the “Identify” button to display a large number on each monitor.
B. Right-click the display icon in the Display Properties dialog that you wish
to be your primary monitor, and then select “Primary”. When you use
multiple monitors with your card, one monitor will always be Primary, and
all additional monitors will be designated as Secondary.
C. Select the display icon identified by the number 2.
D. Click “Extend my Windows desktop onto this monitor”.
E. Right-click the display icon and select “Attached”, if necessary.
F. Set the “Screen Resolution” and “Color Quality” as appropriate for the
second monitor. Click “Apply” or “OK” to apply these new values.
G. Repeat steps C through E for the diaplay icon identified by the number
one, two and three.
Right click the desktop, choose “Personalize”, and select the “Display
Settings” tab so that you can adjust the parameters of the multi-monitor
according to the steps below.
A. Click the number ”2” icon.
19
B. Click the items “This is my main monitor” and “Extend the desktop onto
this monitor”.
C. Click “OK” to save your change.
D. Repeat steps A through C for the display icon identified by the number
one, two and three.
6. Use Multi Monitor feature. Click and drag the display icons to positions
representing the physical setup of your monitors that you would like to use. The
placement of display icons determines how you move items from one monitor to
another.
2.6 Jumpers Setup

The illustration shows how jumpers are
setup. When the jumper cap is placed on
pins, the jumper is “Short”. If no jumper cap
is placed on pins, the jumper is “Open”. The
illustration shows a 3-pin jumper whose pin1
and pin2 are “Short” when jumper cap is
placed on these 2 pins.
Jumper Setting
PS2_USB_PWR1 1_2 2_3 Short pin2, pin3 to enable
(see p.11, No. 1) +5VSB (standby) for PS/2 or
+5V +5VSB
USB01/23 wake up events.
Note: To select +5VSB, it requires 2 Amp and higher standby current provided by
power supply.
USB_PWR2 1_2 2_3 Short pin2, pin3 to enable

(see p.11, No. 15) +5VSB (standby) for
+5V +5VSB
USB4_5/6_7/8_9 wake up
events.
Note: To select +5VSB, it requires 2 Amp and higher standby current provided by
power supply.
Clear CMOS Jumper 1_2 2_3

(CLRCMOS1)
(see p.11, No. 22) Default Clear CMOS
Note: CLRCMOS1 allows you to clear the data in CMOS. The data in CMOS includes
system setup information such as system password, date, time, and system
setup parameters. To clear and reset the system parameters to default setup,
please turn off the computer and unplug the power cord from the power
supply. After waiting for 15 seconds, use a jumper cap to short pin2 and pin3
on CLRCMOS1 for 5 seconds. However, please do not clear the CMOS right
20
after you update the BIOS. If you need to clear the CMOS when you just finish
updating the BIOS, you must boot up the system first, and then shut it down
before you do the clear-CMOS action.
2.7 Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place

jumper caps over these headers and connectors. Placing jumper caps
over the headers and connectors will cause permanent damage of the
motherboard!
•
Floppy Connector
(33-pin FLOPPY1)
Pin1 FLOPPY1
(see p.11 No. 24)
the red-striped side to Pin1
Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the
connector.
Primary IDE connector (Blue)

(39-pin IDE1, see p.11 No. 9)
PIN1 IDE1
connect the blue end connect the black end

to the motherboard to the IDE devices
80-conductor ATA 66/100/133 cable
Note: Please refer to the instruction of your IDE device vendor for the details.
Serial ATAII Connectors These four Serial ATAII (SATAII)

(SATAII_1 (PORT 0.0): SATAII_1 SATAII_3 connectors support SATAII
see p.11, No. 10) (PORT 0.0) (PORT 1.0) or SATA hard disk for internal
(SATAII_2 (PORT 0.1): storage devices. The current
see p.11, No. 13) SATAII interface allows up to
(SATAII_3 (PORT 1.0): SATAII_2 SATAII_4 3.0 Gb/s data transfer rate.
see p.11, No. 11) (PORT 0.1) (PORT 1.1)
(SATAII_4 (PORT 1.1):
see p.11, No. 12)
Serial ATA (SATA) Either end of the SATA data cable

Data Cable can be connected to the SATA /
(Optional) SATAII hard disk or the SATAII
connector on the motherboard.
21
USB 2.0 Headers USB_PWR
P-9 Besides four default USB 2.0
P+9
(9-pin USB8_9) GND
DUMMY
ports on the I/O panel, there are
(see p.11 No. 16) three USB 2.0 headers on this
1
GND motherboard. Each USB 2.0

P+8
P-8
USB_PWR header can support two USB
USB_PWR
2.0 ports.
(9-pin USB6_7) P-7
P+7
(see p.11 No. 17) GND
DUMMY
1
GND
P+6
P-6
USB_PWR
USB_PWR
P-5
(9-pin USB4_5) P+5
GND
(see p.11 No. 18) DUMMY
1
GND
P+4
P-4
USB_PWR
Print Port Header AFD#

This is an interface for print
ERROR#
(25-pin LPT1) PINIT#
SLIN# GND
port cable that allows
(see p.11 No. 23) convenient connection of printer
1
SPD7
SPD6 ACK#
devices.
SPD5 BUSY
SPD4 PE
SPD3 SLCT
SPD2
SPD1
SPD0
STB#
Internal Audio Connectors This connector allows you

(4-pin CD1) CD1 to receive stereo audio input
(CD1: see p.11 No. 26) from sound sources such as
CD-R
GND
GND
CD-L
a CD-ROM, DVD-ROM, TV
tuner card, or MPEG card.
Front Panel Audio Header GND

PRESENCE#
This is an interface for the front
MIC_RET
(9-pin HD_AUDIO1) OUT_RET panel audio cable that allows
(see p.11, No. 27) convenient connection and
1
OUT2_L
control of audio devices.
J_SENSE
OUT2_R
MIC2_R
MIC2_L
1. High Definition Audio supports Jack Sensing, but the panel wire on
the chassis must support HDA to function correctly. Please follow the
instruction in our manual and chassis manual to install your system.
2. If you use AC’97 audio panel, please install it to the front panel audio
header as below:
A. Connect Mic_IN (MIC) to MIC2_L.
B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.
22
C. Connect Ground (GND) to Ground (GND).
D. MIC_RET and OUT_RET are for HD audio panel only. You don’t
need to connect them for AC’97 audio panel.
System Panel Header PLED+ This header accommodates

PLED-
(9-pin PANEL1)
PWRBTN#
GND several system front panel
(see p.11 No. 20) functions.
1
DUMMY
RESET#
GND
HDLED-
HDLED+
Chassis Speaker Header Please connect the chassis

1
(4-pin SPEAKER 1) SPEAKER speaker to this header.
DUMMY
(see p.11 No. 19) DUMMY
+5V
Chassis and Power Fan Connectors Please connect the fan cables
(3-pin CHA_FAN1) to the fan connectors and
(see p.11 No. 21) GND
+12V
match the black wire to the
CHA_FAN_SPEED
ground pin.
GND
(3-pin PWR_FAN1) +12V
(see p.11 No. 25) PWR_FAN_SPEED
CPU Fan Connector 4 3 2 1 Please connect the CPU fan

(4-pin CPU_FAN1) cable to this connector and
(see p.11 No. 2) +12V
GND match the black wire to the
CPU_FAN_SPEED
FAN_SPEED_CONTROL ground pin.
Though this motherboard provides 4-Pin CPU fan (Quiet Fan) support, the 3-Pin
CPU fan still can work successfully even without the fan speed control function.
If you plan to connect the 3-Pin CPU fan to the CPU fan connector on this
motherboard, please connect it to Pin 1-3. Pin 1-3 Connected
3-Pin Fan Installation
ATX Power Connector 12 24 Please connect an ATX power

(24-pin ATXPWR1) supply to this connector.
(see p.11 No. 8)
1 13
23
Though this motherboard provides 24-pin ATX power connector, 12 24
it can still work if you adopt a traditional 20-pin ATX power supply.
To use the 20-pin ATX power supply, please plug your power
supply along with Pin 1 and Pin 13.
20-Pin ATX Power Supply Installation

1 13
ATX 12V Power Connector Please note that it is necessary

(4-pin ATX12V1) to connect a power supply with
(see p.11 No. 3) ATX 12V plug to this connector.
Failing to do so will cause power
up failure.
24
2.8 SA
SATTAII Hard Disk Setup Guide
Before installing SATAII hard disk to your computer, please carefully read below
SATAII hard disk setup guide. Some default setting of SATAII hard disks may not be
at SATAII mode, which operate with the best performance. In order to enable SATAII
function, please follow the below instruction with different vendors to correctly adjust
your SATAII hard disk to SATAII mode in advance; otherwise, your SATAII hard disk
may fail to run at SATAII mode.
Western Digital
7 5 3 1
8 6 4 2
If pin 5 and pin 6 are shorted, SATA 1.5Gb/s will be enabled.

On the other hand, if you want to enable SATAII 3.0Gb/s, please remove the
jumpers from pin 5 and pin 6.
SAMSUNG
7 5 3 1
8 6 4 2
If pin 3 and pin 4 are shorted, SATA 1.5Gb/s will be enabled.

On the other hand, if you want to enable SATAII 3.0Gb/s, please remove the
jumpers from pin 3 and pin 4.
HITACHI
Please use the Feature Tool, a DOS-bootable tool, for changing various ATA
features. Please visit HITACHI’s website for details:
http://www.hitachigst.com/hdd/support/download.htm
The above examples are just for your reference. For different SATAII hard
disk products of different vendors, the jumper pin setting methods may not
be the same. Please visit the vendors’ website for the updates.
25
2.9 Serial A
ATTA (SA
(SATTA) / Serial A
ATTAII (SA
(SATTAII) Hard Disks
Installation
This motherboard adopts NVIDIA® GeForce 7025 / nForce 630a chipset that supports
Serial ATA (SATA) / Serial ATAII (SATAII) hard disks and RAID functions. You may
install SATA / SATAII hard disks on this motherboard for internal storage devices. This
section will guide you to install the SATA / SATAII hard disks.
STEP 1: Install the SATA / SATAII hard disks into the drive bays of your chassis.
STEP 2: Connect the SATA power cable to the SATA / SATAII hard disk.
STEP 3: Connect one end of the SATA data cable to the motherboard’s SATAII
connector.
STEP 4: Connect the other end of the SATA data cable to the SATA / SATAII hard
disk.
2 . 1 0 Hot Plug and Hot Swap FFunctions

unctions for SA
SATTA / SA
SATTAII
HDDs
This motherboard supports Hot Plug and Hot Swap functions for SATA / SATAII
Devices.
NOTE
What is Hot Plug Function?
If the SATA / SATAII HDDs are NOT set for RAID configuration, it is
called “Hot Plug” for the action to insert and remove the SATA / SATAII
HDDs while the system is still power-on and in working condition.
However, please note that it cannot perform Hot Plug if the OS has
been installed into the SATA / SATAII HDD.
What is Hot Swap Function?

If SATA / SATAII HDDs are built as RAID1 or RAID 5 then it is called
“Hot Swap” for the action to insert and remove the SATA / SATAII
HDDs while the system is still power-on and in working condition.
26
2.11 SA
SATTA / SA
SATTAII HDD Hot Plug FFeature
eature and Operation
Guide
This motherboard supports Hot Plug feature for SATA / SATAII HDD in RAID mode.
Please read below operation guide of SATA / SATAII HDD Hot Plug feature carefully.
Before you process the SATA / SATAII HDD Hot Plug, please check below cable
accessories from the motherboard gift box pack.
A. 7-pin SATA data cable
B. SATA power cable with SATA 15-pin power connector interface
A. SATA data cable (Red) B. SATA power cable
SATA 7-pin The SATA 15-pin power 1x4-pin conventional

connector connector (Black) connect power connector (White)
to SATA / SATAII HDD connect to power supply
Caution
1. Without SATA 15-pin power connector interface, the SATA / SATAII Hot Plug
cannot be processed.
2. Even some SATA / SATAII HDDs provide both SATA 15-pin power connector
and IDE 1x4-pin conventional power connector interfaces, the IDE 1x4-pin
conventional power connector interface is definitely not able to support Hot
Plug and will cause the HDD damage and data loss.
Points of attention, before you process the Hot Plug:

1. Below operation procedure is designed only for our motherboard, which
supports SATA / SATAII HDD Hot Plug.
* The SATA / SATAII Hot Plug feature might not be supported by the chipset
because of its limitation, the SATA / SATAII Hot Plug support information of our
motherboard is indicated in the product spec on our website:
www.asrock.com
2. Make sure your SATA / SATAII HDD can support Hot Plug function from your
dealer or HDD user manual. The SATA / SATAII HDD, which cannot support Hot
Plug function, will be damaged under the Hot Plug operation.
3. Please make sure the SATA / SATAII driver is installed into system properly. The
latest SATA / SATAII driver is available on our support website:
www.asrock.com
4. Make sure to use the SATA power cable & data cable, which are from our
motherboard package.
5. Please follow below instructions step by step to reduce the risk of HDD crash
or data loss.
27
How to Hot Plug a SATA / SATAII HDD:
Points of attention, before you process the Hot Plug:
Please do follow below instruction sequence to process the Hot Plug, improper
procedure will cause the SATA / SATAII HDD damage and data loss.
Step 1 Please connect SATA power cable 1x4-pin end Step 2 Connect SATA data cable to
(White) to the power supply 1x4-pin cable. the motherboard’s SATAII connector.
SATA power cable 1x4-pin

power connector (White)
Step 3 Connect SATA 15-pin power cable connector Step 4 Connect SATA data cable to
(Black) end to SATA / SATAII HDD. the SATA / SATAII HDD.
How to Hot Unplug a SATA / SATAII HDD:

Points of attention, before you process the Hot Unplug:
Please do follow below instruction sequence to process the Hot Unplug, improper
procedure will cause the SATA / SATAII HDD damage and data loss.
Step 1 Unplug SATA data cable from SATA / SATAII HDD side.
Step 2 Unplug SATA 15-pin power cable connector (Black) from SATA / SATAII HDD side.
28
2 . 1 2 Driver Installation Guide
To install the drivers to your system, please insert the support CD to your optical drive
first. Then, the drivers compatible to your system can be auto-detected and listed on
the support CD driver page. Please follow the order from up to bottom side to install
those required drivers. Therefore, the drivers you install can work properly.
2.13 Installing Windows ® 7 / 7 64-bit / Vista TM /

Vista TM 64-bit / XP / XP 64-bit Without RAID Functions
If you just want to install Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit / XP / XP 64-
bit on your SATA / SATAII HDDs without RAID functions, you don’t have to make a
SATA / SATAII driver diskette. Besides, there is no need for you to change the BIOS
setting. You can start to install Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit / XP / XP
64-bit on your system directly.
2.14 Installing Windows ® 7 / 7 64-bit / Vista TM /

Vista TM 64-bit / XP / XP 64-bit With RAID Functions
If you want to install Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit / XP / XP 64-bit OS
on your SATA / SATAII HDDs with RAID functions, please follow below procedures
according to the OS you install.
2.14.1 Installing Windows ® XP / XP 64-bit With RAID

Functions
If you want to install Windows ® XP or Windows ® XP 64-bit on your SATA / SATAII
HDDs with RAID functions, please follow below steps.
STEP 1: Set Up BIOS.

A. Enter BIOS SETUP UTILITY Advanced screen Storage Configuration.
B. Set the “SATA Operation Mode” option to [IDE].
STEP 2: Make a SATA / SATAII Driver Diskette.
A. Insert the ASRock Support CD into your optical drive to boot your system.
B. During POST at the beginning of system boot-up, press <F11> key, and then a
window for boot devices selection appears. Please select CD-ROM as the boot
device.
C. When you see the message on the screen, “Generate Serial ATA driver diskette
[YN]?”, press <Y>.
29
D. Then you will see these messages,
Please insert a blank
formatted diskette into floppy
drive A:
press any key to start
Please insert a floppy diskette into the floppy drive, and press any key.
E. The system will start to format the floppy diskette and copy SATA / SATAII
drivers into the floppy diskette.
B. Set the “SATA Operation Mode” option to [RAID].
STEP 4: Use “RAID Installation Guide” to set RAID configuration.
Before you start to configure RAID function, you need to check the RAID installation
guide in the Support CD for proper configuration. Please refer to the BIOS RAID
installation guide in the following path in the Support CD:
.. \ RAID Installation Guide
STEP 5: Install Windows® XP / XP 64-bit OS on your system.
You can start to install Windows® XP / Windows® XP 64-bit OS on your system. At the
beginning of Windows ® setup, press F6 to install a third-party RAID driver. When
prompted, insert the SATA / SATAII driver diskette containing the NVIDIA® RAID driver.
After reading the floppy disk, the driver will be presented. Select the driver to install
according to the mode you choose and the OS you install.
NOTE. If you install Windows® XP / Windows® XP 64-bit on IDE HDDs and want to manage
(create, convert, delete, or rebuild) RAID functions on SATA / SATAII HDDs, you still
need to set up “SATA Operation Mode” to [RAID] in BIOS first. Then, please set the
RAID configuration by using the Windows RAID installation guide in the following path
in the Support CD:
2.14.2 Installing Windows ® 7 / 7 64-bit / Vista TM /

Vista TM 64-bit With RAID Functions
If you want to install Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit on your SATA /
SATAII HDDs with RAID functions, please follow below steps.

B. Set the “SATA Operation Mode” option to [RAID].
STEP 2: Use “RAID Installation Guide” to set RAID configuration.
Before you start to configure RAID function, you need to check the RAID installation
guide in the Support CD for proper configuration. Please refer to the BIOS RAID
installation guide part of the document in the following path in the Support CD:
30
STEP 3: Install Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS on your
system.
Insert the Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit optical disk into the optical
drive to boot your system, and follow the instruction to install Windows® 7 / 7 64-bit
/ VistaTM / VistaTM 64-bit OS on your system. When you see “Where do you want to
install Windows?” page, please insert the ASRock Support CD into your optical drive,
and click the “Load Driver” button on the left on the bottom to load the NVIDIA® RAID
drivers. NVIDIA® RAID drivers are in the following path in our Support CD:
.. \ I386 (For Windows® VistaTM OS)
.. \ AMD64 (For Windows® VistaTM 64-bit OS)
After that, please insert Windows® VistaTM / VistaTM 64-bit optical disk into the optical
drive again to continue the installation.
NOTE. If you install Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit on IDE HDDs and want to
manage (create, convert, delete, or rebuild) RAID functions on SATA / SATAII HDDs,
you still need to set up “SATA Operation Mode” to [RAID] in BIOS first. Then, please set
the RAID configuration by using the Windows RAID installation guide in the following
path in the Support CD:
NOTE. For Windows® 7 / 7 64-bit users, you do not need to load RAID driver from ASRock
support CD. Please use the native driver to install Windows® 7 / 7 64-bit OS, and then
install ASRock All-in-1 driver.
2 . 1 5 Untied Overclocking TTechnology

echnology
This motherboard supports Untied Overclocking Technology, which means during
overclocking, FSB enjoys better margin due to fixed PCI / PCIE buses. Before you
enable Untied Overclocking function, please enter “Overclock Mode” option of BIOS
setup to set the selection from [Auto] to [CPU, PCIE, Async.]. Therefore, CPU FSB is
untied during overclocking, but PCI / PCIE buses are in the fixed mode so that FSB can
operate under a more stable overclocking environment.
Please refer to the warning on page 8 for the possible overclocking risk before
you apply Untied Overclocking Technology.
31
3. BIOS SETUP UTILITY
3.1 Introduction
This section explains how to use the BIOS SETUP UTILITY to configure your system.
The SPI Memory on the motherboard stores the BIOS SETUP UTILITY. You may run
the BIOS SETUP UTILITY when you start up the computer. Please press <F2> or
<Del> during the Power-On-Self-Test (POST) to enter the BIOS SETUP UTILITY,
otherwise, POST will continue with its test routines.
If you wish to enter the BIOS SETUP UTILITY after POST, restart the system by
pressing <Ctl> + <Alt> + <Delete>, or by pressing the reset button on the system
chassis. You may also restart by turning the system off and then back on.
Because the BIOS software is constantly being updated, the following

BIOS setup screens and descriptions are for reference purpose only,
and they may not exactly match what you see on your screen.
3.1.1 BIOS Menu Bar

The top of thescreen has a menu bar with the following selections:
Main To set up the system time/date information
OC Tweaker To set up overclocking features
Advanced To set up the advanced BIOS features
H/W Monitor To display current hardware status
Boot To set up the default system device to locate and load the
Operating System
Security To set up the security features
Exit To exit the current screen or the BIOS SETUP UTILITY
Use < > key or < > key to choose among the selections on the menu bar,
and then press <Enter> to get into the sub screen.
32
3 . 1 . 2 Navigation Keys
Please check the following table for the function description of each navigation
key.
Navigation Key(s) Function Description

/ Moves cursor left or right to select Screens
/ Moves cursor up or down to select items
+ / - To change option for the selected items
<Enter> To bring up the selected screen
<F1> To display the General Help Screen
<F9> To load optimal default values for all the settings
<F10> To save changes and exit the BIOS SETUP UTILITY
<ESC> To jump to the Exit Screen or exit the current screen
3.2 Main Screen

When you enter the BIOS SETUP UTILITY, the Main screen will appear and display
the system overview.
N68C-GS UCC
BIOS SETUP UTILITY

Main OC Tweaker Advanced H/W Monitor Boot Security Exit
System Overview
Use [Enter], [TAB]
System Time [17:00:09] or [SHIFT-TAB] to
System Date [Fri 02/12/2010] select a field.
BIOS Version : N68C-GS UCC P1.00
Processor Type : AMD Athlon (tm) 64 X2 Dual Core Use [+] or [-] to
Processor 4000+ (64bit) configure system Time.
Processor Speed : 2000MHz
Microcode Update : 40F32/62
L1 Cache Size : 256KB
L2 Cache Size : 2048KB Select Screen
Select Item
Total Memory : 1024MB with 128MB shared memory +- Change Field
Single-Channel Memory Mode Tab Select Field
DDRII_1 : 1024MB/266MHz DDR2_533 F1 General Help
DDRII_2 : None F9 Load Defaults
F10 Save and Exit
ESC Exit
v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.
System Time [Hour:Minute:Second]

Use this item to specify the system time.
System Date [Day Month/Date/Year]
Use this item to specify the system date.
33
N68C-S UCC
BIOS SETUP UTILITY

System Overview
Use [Enter], [TAB]
System Time [17:00:09] or [SHIFT-TAB] to
System Date [Fri 02/12/2010] select a field.
BIOS Version : N68C-S UCC P1.00
Processor Type : AMD Athlon (tm) 64 X2 Dual Core Use [+] or [-] to
Processor 4000+ (64bit) configure system Time.
Processor Speed : 2000MHz
Microcode Update : 40F32/62
L1 Cache Size : 256KB
L2 Cache Size : 2048KB Select Screen
Select Item
Total Memory : 1024MB with 128MB shared memory +- Change Field
Single-Channel Memory Mode Tab Select Field
DDRII_1 : 1024MB/266MHz DDR2_533 F1 General Help
DDRII_2 : None F9 Load Defaults
F10 Save and Exit
ESC Exit
System Time [Hour:Minute:Second]

Use this item to specify the system time.
System Date [Day Month/Date/Year]
Use this item to specify the system date.
34
3.3 OC TTweak
weak er Screen
weaker
In the OC Tweaker screen, you can set up overclocking features.
BIOS SETUP UTILITY

EZ Overclocking
Overclocking may cause
Load Optimized CPU OC Setting [Press Enter] damage to your CPU and
motherboard.
CPU Configuration It should be done at
your own risk and
Overclock Mode [Auto]
expense.
CPU Frequency (MHz) [200]
PCIE Frequency (MHz) [100]
Boot Failure Guard [Enabled]
CPU/LDT Spread Spectrum [Enabled]
PCIE Spread Spectrum [Enabled]
SATA Spread Spectrum [Enabled] Select Screen
Select Item
Processor Maximum Frequency x10.5 2100 MHZ Enter Go to Sub Screen
Processor Maximum Voltage 1.2500 V F1 General Help
Multiplier/Voltage Change [Auto] F9 Load Defaults
HT Bus Speed [Auto] F10 Save and Exit
HT Bus Width [Auto] ESC Exit
EZ Overclocking
Load Optimized CPU OC Setting
You can use this option to load the optiomized CPU overclocking setting.
Configuration options: [Press Enter], [Default], [5% (2520MHz)] to [40%
(3360MHz)]. Please note that overclocking may cause damage to your
CPU and motherboard. It should be done at your own risk and expense.
CPU Configuration
Overclock Mode
Use this to select Overclock Mode. The default value is [Auto]. Configura-
tion options: [Auto], [CPU, PCIE, Sync.], [CPU, PCIE, Async.] and [Optimized].
CPU Frequency (MHz)
Use this option to adjust CPU frequency.
PCIE Frequency (MHz)
Use this option to adjust PCIE frequency.
Boot Failure Guard
Enable or disable the feature of Boot Failure Guard.
CPU/LDT Spread Spectrum
This feature will be set to [Enabled] as default. Configuration options:
[Disabled] and [Enabled].
PCIE Spread Spectrum
SATA Spread Spectrum
35
Processor Maximum Frequency
It will display Processor Maximum Frequency for reference.
North Bridge Maximum Frequency
This option appears only when you adopt Phenom CPU. It will display North
Bridge Maximum Frequency for reference.
Processor Maximum Voltage
It will display Processor Maximum Voltage for reference.
Multiplier/Voltage Change
This item is set to [Auto] by default. If it is set to [Manual], you may adjust the
value of Processor Frequency and Processor Voltage. However, it is
recommended to keep the default value for system stability.
BIOS SETUP UTILITY
EZ Overclocking
Overclocking may cause
Load Optimized CPU OC Setting [Press Enter] damage to your CPU and
motherboard.
CPU Configuration It should be done at
your own risk and
Overclock Mode [Auto]
expense.
CPU Frequency (MHz) [200]
PCIE Frequency (MHz) [100]
Boot Failure Guard [Enabled]
CPU/LDT Spread Spectrum [Enabled]
PCIE Spread Spectrum [Enabled]
SATA Spread Spectrum [Enabled] Select Screen
Select Item
Processor Maximum Frequency x10.5 2100 MHZ Enter Go to Sub Screen
Processor Maximum Voltage 1.2500 V F1 General Help
Multiplier/Voltage Change [Manual]
F9 Load Defaults
Processor Multiplier [x10.5 2100 MHz]
F10 Save and Exit
Processor Voltage [1.2500 V]
ESC Exit
Processor Frequency
This option appears only when you adopt AM2 CPU. This item will show
when “Multiplier/Voltage Change” is set to [Manual]; otherwise, it will be
hidden. The range of the value depends on the CPU you adopt on this
motherboard. However, for system stability, it is not recommended to ad-
just the value of this item.
Processor Voltage
This option appears only when you adopt AM2 CPU. This item will show
when “Multiplier/Voltage Change” is set to [Manual]; otherwise, it will be
hidden. The range of the value depends on the CPU you adopt on this
motherboard. However, for safety and system stability, it is not recom-
mended to adjust the value of this item.
CPU Frequency Multiplier
This option appears only when you adopt Phenom CPU. However, for
safety and system stability, it is not recommended to adjust the value of this
item.
36
NB Frequency Multiplier
This option appears only when you adopt Phenom CPU. However, for
safety and system stability, it is not recommended to adjust the value of this
item.
HT Bus Speed
This feature allows you selecting Hyper-Transport bus speed. Configura-
tion options: [Auto], [x1 200 MHz], [x2 400 MHz], [x3 600 MHz], [x4 800
MHz] and [x5 1000 MHz].
HT Bus Width
This feature allows you selecting Hyper-Transport bus width. Configura-
tion options: [Auto], [8 Bit] and [16 Bit].
ASRock UCC
UCC (Unlock CPU Core) feature simplifies AMD CPU activation. As long as a
simple switch of the BIOS option “ASRock UCC”, you can unlock the extra
CPU core to enjoy an instant performance boost. When UCC feature is
enabled, the dual-core or triple-core CPU will boost to the quad-core
CPU, and some CPU, including quad-core CPU, can also increase L3 cache
size up to 6MB, which means you can enjoy the upgrade CPU performance
with a better price. Please be noted that UCC feature is supported with
AM2+ / AM3 CPU only, and in addition, not every AM2+ / AM3 CPU can
support this function because some CPU’s hidden core may be
malfunctioned.
Memory Configuration
Memory Clock
This item can be set by the code using [Auto]. You can set one of the
standard values as listed for DDR2 memory modules: [200MHz DDR2_400],
[266MHz DDR2_533], [333MHz DDR2_667] and [400MHz DDR2_800]. If you
adopt Phenom CPU, there is one more option: [533MHz DDR2_1066]. You
can set one of the standard values as listed for DDR3 memory modules:
[400MHz DDR3_800], [533MHz DDR3_1066], [667MHz DDR3_1333] and
[800MHz DDR3_1600].
DRAM Voltage
Use this to select DRAM voltage. Configuration options: [Auto], [1.794V] to
[2.201V]. The default value is [Auto].
37
Memory Timing
BIOS SETUP UTILITY
OC Tweaker
Memory Timing
Memory Controller Mode [Unganged]
Power Down Enable [Enabled]
Bank Interleaving [Auto]
Channel Interleaving [Hash 1]
CAS Latency (CL) 4 [Auto]
TRCD 4 [Auto]
TRP 4 [Auto]
TRAS 12 [Auto]
TRTP 2 [Auto]
TRRD 2 [Auto] Select Screen
TWTR 2 [Auto] Select Item
TWR 4 [Auto] +- Change Option
TRC 16 [Auto] F1 General Help
TRWTWB 0 [Auto] F9 Load Defaults
TRWTTO 4 [Auto] F10 Save and Exit
TWRRD 0 [Auto] ESC Exit
TWRWR 2 [Auto]
Memory Controller Mode

This option appears only when you adopt Phenom CPU. It allows you to
adjust the memory controller mode. Configuration options: [Unganged] and
[Ganged]. The default value is [Unganged].
Power Down Enable
Use this item to enable or disable DDR power down mode.
Bank Interleaving
Interleaving allows memory accesses to be spread out over banks on the
same node, or accross nodes, decreasing access contention.
Channel Interleaving
This option appears only when you adopt Phenom CPU. It allows you to
enable Channel Memory Interleaving. The default value for DDR2 is [Hash
1]. The default value for DDR3 is [Hash 2].
CAS Latency (CL)
Use this item to adjust the means of memory accessing. Configuration
options: [Auto], [3CLK], [4CLK], [5CLK] and [6CLK]. The default value is
[Auto].
TRCD
Use this to adjust TRCD values. Configuration options: [Auto], [3CLK], [4CLK],
[5CLK] and [6CLK]. The default value is [Auto].
TRP
Use this to adjust TRP values. Configuration options: [Auto], [3CLK], [4CLK],
TRAS
Use this to adjust TRAS values. Configuration options: [Auto], [5CLK] to
[18CLK]. The default value is [Auto].
TRTP
Use this to adjust TRTP values. Configuration options: [Auto], [2-4CLK] and
[3-5CLK]. The default value is [Auto].
38
TRRD
Use this to adjust TRRD values. Configuration options: [Auto], [2CLK], [3CLK],
TWTR
Use this to adjust TWTR values. Configuration options: [Auto], [1CLK],
TWR
Use this to adjust TWR values. Configuration options: [Auto], [3CLK], [4CLK],
TRC
Use this to adjust TRC values. Configuration options: [11CLK] to [26CLK].
The default value is [Auto].
TRWTWB
Use this to adjust TRWTWB values. Configuration options: [3CLK] to [10CLK].
TRWTTO
This option appears only when you adopt AM2 CPU. Use this to adjust
TRWTTD values. Configuration options: [Auto], [2CLK], [3CLK], [4CLK],
[5CLK], [6CLK], [7CLK], [8CLK] and [9CLK]. The default value is [Auto].
TWRRD
TWRRD values. Configuration options: [Auto], [0CLK], [1CLK], [2CLK] and
TWRWR
TWRWR values. Configuration options: [Auto], [1CLK], [2CLK] and [3CLK].
TRDRD
TRWTTD values. Configuration options: [Auto], [2CLK], [3CLK], [4CLK] and
TRFC0
Use this to adjust TRFC0 values. Configuration options: [Auto], [75ns],
[105ns], [127.5ns], [195ns] and [327.5ns]. The default value is [Auto].
TRFC1
Use this to adjust TRFC1 values. Configuration options: [Auto], [75ns],
[105ns], [127.5ns], [195ns] and [327.5ns]. The default value is [Auto].
MA Timing
Use this to adjust values for MA timing. Configuration options: [Auto], [2T],
[1T]. The default value is [Auto].
39
CHA ADDR/CMD Delay
Use this to adjust values for CHA ADDR/CMD Delay feature. Configuration
options: [Auto], [No Delay], [1/64CLK] to [31/64CLK]. The default value is
[Auto].
CHA ADDR/CMD Setup
Use this to adjust values for CHA ADDR/CMD Setup feature. Configuration
options: [Auto], [1/2CLK] and [1CLK]. The default value is [Auto].
CHA CS/ODT Delay
Use this to adjust values for CHA CS/ODT Delay feature. Configuration
[Auto].
CHA CS/ODT Setup
Use this to adjust values for CHB CS/ODT Setup feature. Configuration
CHB ADDR/CMD Delay
Use this to adjust values for CHB ADDR/CMD Delay feature. Configuration
[Auto].
CHB ADDR/CMD Setup
Use this to adjust values for CHB ADDR/CMD Setup feature. Configuration
CHB CS/ODT Delay
Use this to adjust values for CHB CS/ODT Delay feature. Configuration
[Auto].
CHB CS/ODT Setup
Use this to adjust values for CHB CS/ODT Setup feature. Configuration
CHA CKE Drive
Use this to adjust values for CHA CKE Drive. Configuration options: [Auto],
[1.00x], [1.25x], [1.50x] and [2.00x]. The default value is [Auto].
CHA CS/ODT Drive
Use this to adjust values for CHA CS/ODT Drive. Configuration options:
[Auto], [1.00x], [1.25x], [1.50x] and [2.00x]. The default value is [Auto].
CHA ADDR/CMD Drive
Use this to adjust values for CHA ADDR/CMD Drive. Configuration options:
CHA CLK Drive
Use this to adjust values for CHA CLK Drive. Configuration options: [Auto],
40
CHA DATA Drive
Use this to adjust values for CHA DATA Drive. Configuration options: [Auto],
CHA DQS Drive
Use this to adjust values for CHA DQS Drive. Configuration options: [Auto],
CHA Processor ODT
Use this to adjust values for CHA Processor ODT. Configuration options:
[Auto], [300 ohms], [150 ohms] and [75 ohms]. The default value is [Auto].
CHB CKE Drive
Use this to adjust values for CHB CKE Drive. Configuration options: [Auto],
CHB CS/ODT Drive
Use this to adjust values for CHB CS/ODT Drive. Configuration options:
CHB ADDR/CMD Drive
Use this to adjust values for CHB ADDR/CMD Drive. Configuration options:
CHB CLK Drive
Use this to adjust values for CHB CLK Drive. Configuration options: [Auto],
CHB DATA Drive
Use this to adjust values for CHB DATA Drive. Configuration options: [Auto],
CHB DQS Drive
Use this to adjust values for CHB DQS Drive. Configuration options: [Auto],
CHB Processor ODT
Use this to adjust values for CHB Processor ODT. Configuration options:
[Auto], [300 ohms], [150 ohms] and [75 ohms]. The default value is [Auto].
Chipset Settings
Chipset Voltage
Use this to select chipset voltage. Configuration options: [Auto], [1.262V] to
[1.423V]. The default value is [Auto].
Would you like to save current setting user defaults?

In this option, you are allowed to load and save three user defaults
according to your own requirements.
41
3.4 Advanced Screen
In this section, you may set the configurations for the following items: CPU
Configuration, Chipset Configuration, ACPI Configuration, Storage Configuration, PCIPnP
Configuration, Floppy Configuration, SuperIO Configuration, and USB Configuration.
BIOS SETUP UTILITY

Advanced Settings Options for CPU
WARNING : Setting wrong values in below sections

may cause system to malfunction.
CPU Configuration
Chipset Configuration
ACPI Configuration
Storage Configuration
PCIPnP Configuration
Floppy Configuration Select Screen
SuperIO Configuration Select Item
USB Configuration Enter Go to Sub Screen
F1 General Help
BIOS Update Utility F9 Load Defaults
ASRock Instant Flash F10 Save and Exit
ESC Exit
Setting wrong values in this section may cause

the system to malfunction.
ASRock Instant Flash

ASRock Instant Flash is a BIOS flash utility embedded in Flash ROM. This
convenient BIOS update tool allows you to update system BIOS without
entering operating systems first like MS-DOS or Windows®. Just launch
this tool and save the new BIOS file to your USB flash drive, floppy disk or
hard drive, then you can update your BIOS only in a few clicks without
preparing an additional floppy diskette or other complicated flash utility.
Please be noted that the USB flash drive or hard drive must use FAT32/16/
12 file system. If you execute ASRock Instant Flash utility, the utility will
show the BIOS files and their respective information. Select the proper
BIOS file to update your BIOS, and reboot your system after BIOS update
process completes.
42
3.4.1 CPU Configuration
BIOS SETUP UTILITY
Advanced
CPU Configuration Options
AM2 Boost [Disabled] Enabled

Cool' n' Quiet [Auto] Disabled
Secure Virtual Machine [Enabled]
Select Screen
Select Item
+- Change Option
F1 General Help
F9 Load Defaults
F10 Save and Exit
ESC Exit
AM2 Boost
This option appears only when you adopt AM2 CPU. If you set this option to
[Enabled], you will enable ASRock AM2 Boost function, which will improve the
memory performance. The default value is [Disabled]. Please refer to cau-
tion 17 on page 10 for details.
Cool ‘n’ Quiet
Use this item to enable or disable AMD’s Cool ‘n’ QuietTM technology. The
default value is [Auto]. Configuration options: [Auto], [Enabled] and
[Disabled]. If you install Windows® VistaTM and want to enable this function,
please set this item to [Enabled]. Please note that enabling this function may
reduce CPU voltage and memory frequency, and lead to system stability or
compatibility issue with some memory modules or power supplies. Please
set this item to [Disable] if above issue occurs.
Secure Virtual Machine
This option appears only when you adopt AM2 CPU. When this option is set
to [Enabled], a VMM (Virtual Machine Architecture) can utilize the additional
hardware capabilities provided by AMD-V. The default value is [Enabled].
Configuration options: [Enabled] and [Disabled].
Enhance Halt State
This option appears only when you adopt Phenom CPU. All processors
support the Halt State (C1). The C1 state is supported through the native
processor instructions HLT and MWAIT and requires no hardware support
from the chipset. In the C1 power state, the processor maintains the con-
text of the system caches.
L3 Cache Allocation
This option appears only when you adopt Phenom CPU. The default value
is [BSP Only]. Configuration options: [BSP Only] and [All Cores].
43
3 . 4 . 2 Chipset Configuration
BIOS SETUP UTILITY
Advanced
Chipset Settings Auto/Enable/Disable

Onboard HD Audio.
Onboard LAN [Auto]
Onboard HD Audio [Auto]
Front Panel [Enabled]
Share Memory [Auto]
Primary Graphics Adapter [PCI]
CPU Thermal Throttle [Enabled]
Select Screen
Select Item
+- Change Option
F1 General Help
F9 Load Defaults
F10 Save and Exit
ESC Exit
Onboard LAN
This allows you to enable or disable the onboard LAN feature.
Onboard HD Audio
Select [Auto], [Enabled] or [Disabled] for the onboard HD Audio feature. If you
select [Auto], the onboard HD Audio will be disabled when PCI Sound Card is
plugged.
Front Panel
Select [Auto], [Enabled] or [Disabled] for the onboard HD Audio Front Panel.
Share Memory
This allows you to set share memory feature. The default value is [Auto].
Configuration options: [Auto], [32MB], [64MB], [128MB] and [256MB].
Primary Graphics Adapter
This item will switch the PCI Bus scanning order while searching for video
card. It allows you to select the type of Primary VGA in case of multiple
video controllers. The default value of this feature is [PCI]. Configuration
options: [PCI], [Onboard] and [PCI Express].
CPU Thermal Throttle
Use this to enable CPU internal thermal control mechanism to keep the CPU
from overheated. The default value is [Enabled].
44
3.4.3 ACPI Configuration
BIOS SETUP UTILITY
Advanced
ACPI Settings Select auto-detect or

disable the STR
Suspend To RAM [Auto] feature.
Check Ready Bit [Enabled]
Away Mode Support [Disabled]
Restore on AC / Power Loss [Power Off]

Ring-In Power On [Disabled]
PCI Devices Power On [Disabled]
PS / 2 Keyboard Power On [Disabled]
RTC Alarm Power On [Disabled] Select Screen
Select Item
ACPI HPET Table [Disabled] +- Change Option
OSC Control [Auto] F1 General Help
F9 Load Defaults
F10 Save and Exit
ESC Exit
Suspend to RAM
Use this item to select whether to auto-detect or disable the Suspend-to-RAM
feature. Select [Auto] will enable this feature if the OS supports it. If you set
this item to [Disabled], the function “Repost Video on STR Resume” will be
hidden.
Check Ready Bit
Use this item to enable or disable the feature Check Ready Bit.
Away Mode Support
Use this item to enable or disable Away Mode support under Windows® XP
Media Center OS. The default value is [Disabled].
Restore on AC/Power Loss
This allows you to set the power state after an unexpected AC/power
loss. If [Power Off] is selected, the AC/power remains off when the
power recovers. If [Power On] is selected, the AC/power resumes
and the system starts to boot up when the power recovers.
Ring-In Power On
Use this item to enable or disable Ring-In signals to turn on the system from
the power-soft-off mode.
PCI Devices Power On
Use this item to enable or disable PCI devices to turn on the system from the
power-soft-off mode.
PS/2 Keyboard Power On
Use this item to enable or disable PS/2 keyboard to turn on the system from
the power-soft-off mode.
45
RTC Alarm Power On
Use this item to enable or disable RTC (Real Time Clock) to power on the
system.
ACPI HPET Table
Use this item to enable or disable ACPI HPET Table. The default value is
[Disabled]. Please set this option to [Enabled] if you plan to use this
motherboard to submit Windows® VistaTM certification.
OSC Control
Use this item to enable or disable OSC control. Configuration options: [Auto],
[Enabled] and [Disabled]. The default value is [Auto].
46
3.4.4 Storage Configuration
BIOS SETUP UTILITY
Advanced
Options
Storage Configuration
Disabled
Onboard IDE Controller [Enabled] Enabled
Onboard SATA Controller [Enabled]
SATA Operation Mode [IDE]
IDE1 Master [Hard Disk]

IDE1 Slave [Not Detected]
SATAII_1 [Not Detected]
SATAII_4 [Not Detected] Select Screen
Select Item
+- Change Option
F1 General Help
F9 Load Defaults
F10 Save and Exit
ESC Exit
OnBoard IDE Controller

Use this item to enable or disable the “OnBoard IDE Controller” feature.
Onboard SATA Controller
Use this item to enable or disable the “Onboard SATA Controller” feature.
SATA Operation Mode
Use this item to adjust SATA Operation Mode. The default value of this option
is [IDE]. If you want to operate RAID function on SATA / SATAII HDDs, please
select [RAID]. Configuration options: [IDE] and [RAID].
* If you select [RAID] mode, SATA / SATAII HDDs can not be accessed until you finish
configuring RAID functions in NVIDIA BIOS / Windows RAID Utility.
* If you install OS on SATA / SATAII HDDs, please do not change the setting of this
item after OS installation.
IDE Device Configuration
You may set the IDE configuration for the device that you specify. We will use
the “IDE1 Master” as the example in the following instruction, which can be
applied to the configurations of “IDE1 Slave” as well.
BIOS SETUP UTILITY

Advanced
IDE Master Select the type

of device connected
Device :Hard Disk to the system.
Vendor :MAXTOR 6L080J4
Size :80.0 GB
LBA Mode :Supported
Block Mode :16Sectors
PIO Mode :4
Async DMA :MultiWord DMA-2
Ultra DMA :Ultra DMA-6
S.M.A.R.T. :Supported
Type [Auto] Select Screen

LBA/Large Mode [Auto]
[Auto]
Select Item
Block (Multi-Sector Transfer)
PIO Mode [Auto] +- Change Option
DMA Mode [Auto] F1 General Help
S.M.A.R.T. [Disabled] F9 Load Defaults
32Bit Data Transfer [Disabled] F10 Save and Exit
ESC Exit
47
TYPE
Use this item to configure the type of the IDE device that you specify.
Configuration options: [Not Installed], [Auto], [CD/DVD], and [ARMD].
[Not Installed]: Select [Not Installed] to disable the use of IDE device.
[Auto]: Select [Auto] to automatically detect the hard disk drive.
After selecting the hard disk information into BIOS, use a disk
utility, such as FDISK, to partition and format the new IDE hard
disk drives. This is necessary so that you can write or read data
from the hard disk. Make sure to set the partition of the Primary
IDE hard disk drives to active.
[CD/DVD]:This is used for IDE CD/DVD drives.

[ARMD]: This is used for IDE ARMD (ATAPI Removable Media Device),
such as MO.
LBA/Large Mode
Use this item to select the LBA/Large mode for a hard disk > 512 MB under
DOS and Windows; for Netware and UNIX user, select [Disabled] to
disable the LBA/Large mode.
Block (Multi-Sector Transfer)
The default value of this item is [Auto]. If this feature is enabled, it will
enhance hard disk performance by reading or writing more data during
each transfer.
PIO Mode
Use this item to set the PIO mode to enhance hard disk performance by
optimizing the hard disk timing.
DMA Mode
DMA capability allows the improved transfer-speed and data-integrity for com-
patible IDE devices.
S.M.A.R.T.
Use this item to enable or disable the S.M.A.R.T. (Self-Monitoring, Analysis,
and Reporting Technology) feature. Configuration options: [Disabled], [Auto],
[Enabled].
32Bit Data Transfer
Use this item to enable 32-bit access to maximize the IDE hard disk data
transfer rate.
48
3.4.5 PCIPnP Configuration
BIOS SETUP UTILITY
Advanced
Advanced PCI / PnP Settings Value in units of PCI

clocks for PCI device
PCI Latency Timer [32] latency timer
PCI IDE BusMaster [Enabled] register.
Select Screen
Select Item
+- Change Option
F1 General Help
F9 Load Defaults
F10 Save and Exit
ESC Exit
Setting wrong values in this section may cause

the system to malfunction.
PCI Latency Timer

The default value is 32. It is recommended to keep the default value unless
the installed PCI expansion cards’ specifications require other settings.
PCI IDE BusMaster
Use this item to enable or disable the PCI IDE BusMaster feature.
49
3 . 4 . 6 Floppy Configuration
In this section, you may configure the type of your floppy drive.
BIOS SETUP UTILITY

Advanced
Floppy Configuration Select the type of

floppy drive
Floppy A [1.44 MB 31 2"] connected to the
system.
Select Screen
Select Item
+- Change Option
F1 General Help
F9 Load Defaults
F10 Save and Exit
ESC Exit
3 . 4 . 7 Super IO Configuration
BIOS SETUP UTILITY

Advanced
Configure Super IO Chipset Allow BIOS to Enable

or Disable Floppy
OnBoard Floppy Controller [Enabled] Controller.
Serial Port Address [3F8 / IRQ4]
Parallel Port Address [378]
Parallel Port Mode [ECP + EPP]
EPP Version [1.9]
ECP Mode DMA Channel [DMA3]
Parallel Port IRQ [IRQ7]
Select Screen
Select Item
+- Change Option
F1 General Help
F9 Load Defaults
F10 Save and Exit
ESC Exit
OnBoard Floppy Controller

Use this item to enable or disable floppy drive controller.
Serial Port Address
Use this item to set the address for the onboard serial port or disable it.
Configuration options: [Disabled], [3F8 / IRQ4], [2F8 / IRQ3], [3E8 / IRQ4],
[2E8 / IRQ3].
Parallel Port Address
Use this item to set the address for the onboard parallel port or disable it.
Configuration options: [Disabled], [378], and [278].
50
Parallel Port Mode
Use this item to set the operation mode of the parallel port. The default
value is [ECP+EPP]. If this option is set to [ECP+EPP], it will show the
EPP version in the following item, “EPP Version”. Configuration options:
[Normal], [Bi-Directional], and [ECP+EPP].
EPP Version
Use this item to set the EPP version. Configuration options: [1.9]
and [1.7].
ECP Mode DMA Channel
Use this item to set the ECP mode DMA channel. Configuration
options: [DMA0], [DMA1], and [DMA3].
Parallel Port IRQ
Use this item to set the IRQ for the parallel port. Configuration options:
[IRQ5] and [IRQ7].
51
3 . 4 . 8 USB Configuration
BIOS SETUP UTILITY
Advanced
USB Configuration To enable or disable

the onboard USB
USB Controller [Enabled] controllers.
USB 2.0 Support [Enabled]
Legacy USB Support [Enabled]
Select Screen
Select Item
+- Change Option
F1 General Help
F9 Load Defaults
F10 Save and Exit
ESC Exit
USB Controller
Use this item to enable or disable the use of USB controller.
USB 2.0 Support
Use this item to enable or disable the USB 2.0 support.
Legacy USB Support
Use this option to select legacy support for USB devices. There are four
configuration options: [Enabled], [Auto], [Disabled] and [BIOS Setup Only].
The default value is [Enabled]. Please refer to below descriptions for the
details of these four options:
[Enabled] - Enables support for legacy USB.
[Auto] - Enables legacy support if USB devices are connected.
[Disabled] - USB devices are not allowed to use under legacy OS and BIOS
setup when [Disabled] is selected. If you have USB compatibility issue, it is
recommended to select [Disabled] to enter OS.
[BIOS Setup Only] - USB devices are allowed to use only under BIOS
setup.
52
3.5 Hardware Health Event Monitoring Screen
In this section, it allows you to monitor the status of the hardware on your system,
including the parameters of the CPU temperature, motherboard temperature, CPU fan
speed, chassis fan speed, and the critical voltage.
BIOS SETUP UTILITY

Enable/Disable
Hardware Health Event Monitoring CPU Quiet Fan
Function.
CPU Temperature : 37 C / 98 F
M / B Temperature : 27 C / 80 F
CPU Fan Speed : 4722 RPM

Chassis Fan Speed : N/A
Power Fan Speed : N/A
Vcore : 1.216V
+ 3.30V : 3.248V Select Screen
+ 5.00V : 5.136V Select Item
+ 12.00V : 12.091V F1 General Help
F9 Load Defaults
CPU Quiet Fan [Disabled] F10 Save and Exit
ESC Exit
CPU Quiet Fan

This item allows you to control the CPU fan speed and fan noise. If you set this
option as [Disabled], the CPU fan will operate in full speed. If you set this
option as [Enabled], you will find the items “Target CPU Temperature” and
“Target Fan Speed” appear to allow you adjusting them. The default value is
[Disabled]. You are allowed to enable this function only when you install 4-pin
CPU fan.
Target CPU Temperature
The target temperature will be between 45 C/113 F and 65 C/149 F. The
default value is [50 C/122 F].
Target Fan Speed
Use this option to set the target fan speed. You can freely adjust the
target fan speed according to the target CPU temperature that you
choose. The default value is [Fast]. Configuration options: [Fast], [Middle]
and [Slow].
53
3.6 Boot Screen
In this section, it will display the available devices on your system for you to config-
ure the boot settings and the boot priority.
BIOS SETUP UTILITY

Boot Settings Configure Settings

during System Boot.
Boot Settings Configuration
1st Boot Device [1st Floppy Device]

2nd Boot Device [HDD: PM - HDS722580VL]
3rd Boot Device [CD / DVD: 3S - CD - ROM C]
4th Boot Device [USB]
Hard Disk Drives
Removable Drives
CD/DVD Drives Select Screen
Select Item
Enter Go to Sub Screen
F1 General Help
F9 Load Defaults
F10 Save and Exit
ESC Exit
3 . 6 . 1 Boot Settings Configuration

BIOS SETUP UTILITY
Boot
Boot Settings Configuration Disabled: Displays

normal POST messages.
Full Screen Logo [Enabled] Enabled: Displays OEM
AddOn ROM Display [Enabled] Logo instead of POST
Boot Logo [Auto] messages.
Boot From Onboard LAN [Disabled]
Bootup Num-Lock [On]
Select Screen
Select Item
+- Change Option
F1 General Help
F9 Load Defaults
F10 Save and Exit
ESC Exit
Full Screen Logo

Use this item to enable or disable OEM Logo. The default value is [Enabled].
AddOn ROM Display
Use this option to adjust AddOn ROM Display. If you enable the option
“Full Screen Logo” but you want to see the AddOn ROM information when
the system boots, please select [Enabled]. Configuration options: [Enabled]
and [Disabled]. The default value is [Enabled].
Boot Logo
Use this option to select logo in POST screen. This option only appears
when you enable the option “Full Screen Logo”. Configuration options:
[Auto], [S-series], [Scenery] and [ASRock]. The default value is [Auto].
Currently, the option [Auto] is set to Aircraft.
54
Boot From Onboard LAN
Use this item to enable or disable the Boot From Onboard LAN feature.
Boot Up Num-Lock
If this item is set to [On], it will automatically activate the Numeric Lock
function after boot-up.
3.7 Security Screen

In this section, you may set or change the supervisor/user password for the system.
For the user password, you may also clear it.
BIOS SETUP UTILITY

Security Settings Install or Change the

password.
Supervisor Password : Not Installed
User Password : Not Installed
Change Supervisor Password

Change User Password
Select Screen
Select Item
Enter Change
F1 General Help
F9 Load Defaults
F10 Save and Exit
ESC Exit
55
3 . 8 Exit Screen
BIOS SETUP UTILITY
Exit Options
Exit system setup
after saving the
Save Changes and Exit changes.
Discard Changes and Exit
Discard Changes F10 key can be used
for this operation.
Load BIOS Defaults
Load Performance Setup Default (IDE/SATA)
Load Performance Setup RAID Mode
Load Power Saving Setup Default
Select Screen
Select Item
Enter Go to Sub Screen
F1 General Help
F9 Load Defaults
F10 Save and Exit
ESC Exit
Save Changes and Exit

When you select this option, it will pop-out the following message, “Save
configuration changes and exit setup?” Select [OK] to save the changes
and exit the BIOS SETUP UTILITY.
Discard Changes and Exit
When you select this option, it will pop-out the following message, “Dis-
card changes and exit setup?” Select [OK] to exit the BIOS SETUP UTILITY
without saving any changes.
Discard Changes
When you select this option, it will pop-out the following message, “Dis-
card changes?” Select [OK] to discard all changes.
Load BIOS Defaults
Load BIOS default values for all the setup questions. F9 key can be used
for this operation.
Load Performance Setup Default (IDE/SATA)
This performance setup default may not be compatible with all system
configurations. If system boot failure occurs after loading, please resume
optimal default settings. F5 key can be used for this operation.
Load Performance Setup RAID Mode
This performance setup RAID mode may not be compatible with all system
configurations. If system boot failure occurs after loading, please resume
optimal default settings. F4 key can be used for this operation.
Load Power Saving Setup Default
Load power saving setup default. F6 key can be used for this operation.
56
Supportt
4. Sof tware Suppor
4.1 Install Operating System
This motherboard supports various Microsoft® Windows® operating systems: 7 /
7 64-bit / VistaTM / VistaTM 64-bit / XP / XP 64-bit. Because motherboard settings and
hardware options vary, use the setup procedures in this chapter for general refer-
ence only. Refer to your OS documentation for more information.
4.2 Support CD Information

The Support CD that came with the motherboard contains necessary drivers and
useful utilities that enhance the motherboard features.
4.2.1 Running The Support CD

To begin using the support CD, insert the CD into your CD-ROM drive. The CD
automatically displays the Main Menu if “AUTORUN” is enabled in your computer.
If the Main Menu did not appear automatically, locate and double click on the file
“ASSETUP.EXE” from the BIN folder in the Support CD to display the menus.
4.2.2 Drivers Menu

The Drivers Menu shows the available devices drivers if the system detects the
installed devices. Please install the necessary drivers to activate the devices.
4.2.3 Utilities Menu

The Utilities Menu shows the applications software that the motherboard supports.
Click on a specific item then follow the installation wizard to install it.
4.2.4 Contact Information

If you need to contact ASRock or want to know more about ASRock, welcome
to visit ASRock’s website at http://www.asrock.com; or you may contact your
dealer for further information.
57

N68C-S Ucc

Uploaded by

Copyright:

Available Formats

N68C-S Ucc

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

N68C-S Ucc

Uploaded by

Copyright:

Available Formats

N68C-GS UCC /

CALIFORNIA, USA ONLY

ASRock Website: http://www.asrock.com

Because the motherboard specifications and the BIOS software might be

1.1 P ack age Contents

Platform - Micro ATX Form Factor: 9.6-in x 8.2-in, 24.4 cm x 20.8 cm

DDR3_A1 (64 bit, 240-pin module)

DDR3_B1 (64 bit, 240-pin module)

DDRII_2 (64 bit, 240-pin module)

CODEC PCI2 CLRCMOS1

1 PS2_USB_PWR1 Jumper 16 USB 2.0 Header (USB8_9, Blue)

1 PS/2 Mouse Port (Green) 6 USB 2.0 Ports (USB01)

select “2 Channel” or “4 Channel”. Click “Power” to save your change.

1 PS/2 Mouse Port (Green) 6 USB 2.0 Ports (USB01)

select “2 Channel” or “4 Channel”. Click “Power” to save your change.

Before you install or remove any component, ensure that the

CPU Golden Triangle

Socker Corner Small Triangle

STEP 1: STEP 2 / STEP 3: STEP 4:

2.2 Installation of CPU Fan and Heatsink

Dual Channel DDR2 Memory Configurations

Dual Channel DDR3 Memory Configurations

1. If you want to install two memory modules, for optimal compatibility

Please make sure to disconnect power supply before adding or

Step 1. Unlock a DIMM slot by pressing the retaining clips outward.

Installing an expansion card

2.6 Jumpers Setup

USB_PWR2 1_2 2_3 Short pin2, pin3 to enable

Clear CMOS Jumper 1_2 2_3

2.7 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place

Primary IDE connector (Blue)

connect the blue end connect the black end

Serial ATAII Connectors These four Serial ATAII (SATAII)

Serial ATA (SATA) Either end of the SATA data cable

GND motherboard. Each USB 2.0

Print Port Header AFD#

Internal Audio Connectors This connector allows you

Front Panel Audio Header GND

System Panel Header PLED+ This header accommodates

Chassis Speaker Header Please connect the chassis

CPU Fan Connector 4 3 2 1 Please connect the CPU fan

3-Pin Fan Installation

ATX Power Connector 12 24 Please connect an ATX power

20-Pin ATX Power Supply Installation

ATX 12V Power Connector Please note that it is necessary

If pin 5 and pin 6 are shorted, SATA 1.5Gb/s will be enabled.

If pin 3 and pin 4 are shorted, SATA 1.5Gb/s will be enabled.

2 . 1 0 Hot Plug and Hot Swap FFunctions

What is Hot Swap Function?

SATA 7-pin The SATA 15-pin power 1x4-pin conventional

Points of attention, before you process the Hot Plug:

SATA power cable 1x4-pin

How to Hot Unplug a SATA / SATAII HDD:

2.13 Installing Windows ® 7 / 7 64-bit / Vista TM /

2.14 Installing Windows ® 7 / 7 64-bit / Vista TM /

2.14.1 Installing Windows ® XP / XP 64-bit With RAID

STEP 1: Set Up BIOS.

2.14.2 Installing Windows ® 7 / 7 64-bit / Vista TM /