Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 16K views

    Dish End Calculations As Per ASME Section VII Div 1

    Uploaded by

    sksiddique
    This document summarizes the calculations to check the thickness of a dished head based on ASME 8 Division 1 Appendix 1 Section 1.4 for heads with a ts/L ratio less than 0.002. It provides the key parameters of the dished head such as inside diameter, knuckle radius, spherical radius, required thickness and design stress. It then calculates the minimum required thickness and compares it to the actual thickness. Additional calculations are shown to check the maximum allowable design pressure for the head. The summary is that the calculated maximum allowable design pressure of 0.1114 MPa is less than the actual design pressure of 0.2 MPa, so the summary statement is that the head thickness is too thin.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd

    Dish End Calculations As Per ASME Section VII Div 1

    Uploaded by

    sksiddique
    16K views2 pages
    This document summarizes the calculations to check the thickness of a dished head based on ASME 8 Division 1 Appendix 1 Section 1.4 for heads with a ts/L ratio less than 0.002. It provides the key parameters of the dished head such as inside diameter, knuckle radius, spherical radius, required thickness and design stress. It then calculates the minimum required thickness and compares it to the actual thickness. Additional calculations are shown to check the maximum allowable design pressure for the head. The summary is that the calculated maximum allowable design pressure of 0.1114 MPa is less than the actual design pressure of 0.2 MPa, so the summary statement is that the head thickness is too thin.

    Original Description:

    ASME section VIII Dish End Calculation

    Original Title

    Dish End Calculations as Per ASME Section VII Div 1

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document summarizes the calculations to check the thickness of a dished head based on ASME 8 Division 1 Appendix 1 Section 1.4 for heads with a ts/L ratio less than 0.002. It provides the key parameters of the dished head such as inside diameter, knuckle radius, spherical radius, required thickness and design stress. It then calculates the minimum required thickness and compares it to the actual thickness. Additional calculations are shown to check the maximum allowable design pressure for the head. The summary is that the calculated maximum allowable design pressure of 0.1114 MPa is less than the actual design pressure of 0.2 MPa, so the summary statement is that the head thickness is too thin.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    16K views2 pages

    Dish End Calculations As Per ASME Section VII Div 1

    Uploaded by

    sksiddique
    This document summarizes the calculations to check the thickness of a dished head based on ASME 8 Division 1 Appendix 1 Section 1.4 for heads with a ts/L ratio less than 0.002. It provides the key parameters of the dished head such as inside diameter, knuckle radius, spherical radius, required thickness and design stress. It then calculates the minimum required thickness and compares it to the actual thickness. Additional calculations are shown to check the maximum allowable design pressure for the head. The summary is that the calculated maximum allowable design pressure of 0.1114 MPa is less than the actual design pressure of 0.2 MPa, so the summary statement is that the head thickness is too thin.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    1 of 2

    ASME 8 Div 1 Appendix 1


    Section 1.4 f Dished Heads
    With ts/L < 0.002
    ASME 8 Division 1:- Torispherical Ends To UG32 and Appendix 1.4
    P := 0.2

    Design Pressure Mpa

    (Note:- 1 Mpa = 1 N/mm^2)

    D := 3000

    Inside Diameter mm

    r := 200

    Knuckle Radius mm

    L := 2450

    Spherical Radius mm

    t := 3.4

    Min Required Thickness After forming mm

    S := 138

    Design Stress Mpa

    Sy := 165.2

    Yield Strength at max design temp Mpa

    ET := 184590

    Youngs Modulus At Temperature Mpa

    E := 1

    Joint Factor

    ___________________________________________________________________
    L

    3 +

    M :=

    M = 1.625

    tmin :=

    P L M

    tmin = 2.885 mm

    2 S E 0.2 P

    if tmin < t , "Acceptable Calculation" , "Head Too Thin"


    t
    L

    ) = "Acceptable Calculation"

    = 0.001

    Additional rules for thin heads


    C1 := if

    > 0.08 , 0.692

    r
    D

    t/L < 0.002

    + 0.605 , 9.31

    t
    Se := C1 ET
    r
    r

    > 0.08 , 1.46 2.6

    0.086

    C1 = 0.535
    3

    Se = 1.678 10

    C2 := if

    r
    D

    r
    D

    , 1.25

    C2 = 1.25

    2 of 2

    ASME 8 Div 1 Appendix 1


    Section 1.4 f Dished Heads
    With ts/L < 0.002
    3

    a := 0.5D r

    a = 1.3 10

    b := L r

    b = 2.25 10

    := acos

    :=

    = 0.955

    L t )

    = 0.456

    c := if < ,

    , a
    ( cos( ) )

    c = 1.48 10

    Re := c + r

    Pe :=

    Py :=

    Re = 1.68 10
    Se t

    Pe = 0.849

    Re
    C2 Re 0.5 1
    r

    Sy t

    Py = 0.084

    Re
    C2 Re 0.5 1
    r

    Pck := if

    Pe

    Pck := if

    Pe

    Py

    Py

    1 , 0.6 Pe , 0.408 Py + 0.192 Pe

    Pck = 0.197

    > 8.29 , 2.0 Py, Pck

    Pck = 0.167

    Maximum Design Pressure P


    Pck
    Pmax :=
    1.5

    if P < Pmax , "Acceptable Calculation" , "Head Too Thin"

    Pmax = 0.1114

    Mpa

    ) = "Head Too Thin"

    ___________________________________________________________________________

    You might also like