SERVICE MANUAL

23" COLOR TELEVISION

SRT2223X

IMPORTANT SAFETY NOTICE

Proper service and repair is important to the safe, reliable operation of all Funai Equipment. The service procedures recommended by Funai and described in this service manual are effective methods of performing service operations. Some of these service special tools should be used when and as recommended. It is important to note that this service manual contains various CAUTIONS and NOTICES which should be carefully read in order to minimize the risk of personal injury to service personnel. The possibility exists that improper service methods may damage the equipment. It also is important to understand that these CAUTIONS and NOTICES ARE NOT EXHAUSTIVE. Funai could not possibly know, evaluate and advice the service trade of all conceivable ways in which service might be done or of the possible hazardous consequences of each way. Consequently, Funai has not undertaken any such broad evaluation. Accordingly, a servicer who uses a service procedure or tool which is not recommended by Funai must first use all precautions thoroughly so that neither his safety nor the safe operation of the equipment will be jeopardized by the service method selected.

TABLE OF CONTENTS
Specifications ........................................................ Important Safety Precautions................................ Standard Notes for Servicing ................................ Disassembly Instructions ...................................... Electrical Adjustment Instructions ......................... Block Diagram....................................................... Schematic Diagram / CBA's and Test Points ....... Schematic Diagram .............................................. 1-1 2-1 3-1 4-1 5-1 6-1 7-1 7-3 CBA Views and Test Points.................................. 7-11 Wave Forms .......................................................... 8-1 Wiring Diagram...................................................... 9-1 IC Pin Function .................................................... 10-1 Cabinet Exploded View ....................................... 11-1 Packing Exploded View ....................................... 11-3 Mechanical Parts List .......................................... 12-1 Electrical Parts List .............................................. 13-1

SPECIFICATIONS
<TUNER>
ANT. Input ------------------- 75ohm Unbal., F type Reference Level ----------- 20Vp-p (CRT Green Cathode) Test Input Signal ---------- 400Hz 30% modulation Condition Picture Sound VHF CATV UHF Unit MHz MHz dBv dBv dBv MHz Nominal 45.75 41.25 15 15 15 2.0 Limit 30 30 40 0.7

Description 1. Intermediate Freq. 2. Peak Picture Sens

3. AFT Pull In Range (10mV input)

<DEFLECTION>
Description 1. Deflection Freq. 2. Linearity 3. Over Scan 4. High Voltage Condition Horizontal Vertical Horizontal Vertical Unit KHz Hz % % % KV Nominal 15.734 60 10 28 Limit 15 10 -

<VIDEO & CHROMA>

Description 1. Misconvergence Condition Center Side Corner APL 100% Horizontal Vertical Unit mm mm mm Ft-L K Line Line Nominal 25 9200K 250 300 Limit 0.4 1.5 2.1 15 -

2. Brightness 3. Color Temperature 4. Resolution

<AUDIO>
1. Audio Output Power

All items are measured across 8 load at speaker output terminal. Description Condition 10% THD 500mW -3dB Unit W % Hz Nominal 1 2 70~11K Limit 0.8 7 -

2. Audio Distortion (w/LPF) 3. Audio Freq. Response Note:

Nominal specifications represent the design specifications. All units should be able to approximate these. Some will exceed and some may drop slightly below these specifications. Limit specifications represent the absolute worst condition that still might be considered acceptable. In no case should a unit fail to meet limit specifications.

1-1

L6550SP

IMPORTANT SAFETY PRECAUTIONS

Prior to shipment from the factory, our products are strictly inspected for recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced.

Safety Precautions for TV Circuit

1. Before returning an instrument to the customer, always make a safety check of the entire instrument, including, but not limited to, the following items: a. Be sure that no built-in protective devices are defective and have been defeated during servicing. (1) Protective shields are provided on this chassis to protect both the technician and the customer. Correctly replace all missing protective shields, including any removed for servicing convenience. (2) When reinstalling the chassis and/or other assembly in the cabinet, be sure to put back in place all protective devices, including but not limited to, nonmetallic control knobs, insulating fishpapers, adjustment and compartment covers/shields, and isolation resistor/capacitor networks. Do not operate this instrument or permit it to be operated without all protective devices correctly installed and functioning. Servicers who defeat safety features or fail to perform safety checks may be liable for any resulting damage. b. Be sure that there are no cabinet openings through which an adult or child might be able to insert their fingers and contact a hazardous voltage. Such openings include, but are not limited to, (1) spacing between the picture tube and the cabinet mask, (2) excessively wide cabinet ventilation slots, and (3) an improperly fitted and/or incorrectly secured cabinet back cover. c. Antenna Cold Check - With the instrument AC plug removed from any AC source, connect an electrical jumper across the two AC plug prongs. Place the instrument AC switch in the on position. Connect one lead of an ohmmeter to the AC plug prongs tied together and touch the other ohmmeter lead in turn to each tuner antenna input exposed terminal screw and, if applicable, to the coaxial connector. If the measured resistance is less than 1.0 megohm or greater than 5.2 megohm, an abnormality exists that must be corrected before the instrument is returned to the customer. Repeat this test with the instrument AC switch in the off position. d. Leakage Current Hot Check - With the instrument completely reassembled, plug the AC line cord directly into a 120V AC outlet. (Do not use an isolation transformer during this test.) Use a leak-

age current tester or a metering system that complies with American National Standards Institute (ANSI) C101.1 Leakage Current for Appliances and Underwriters Laboratories (UL) 1410, (50.7). With the instrument AC switch first in the on position and then in the off position, measure from a known earth ground (metal water pipe, conduit, etc.) to all exposed metal parts of the instrument (antennas, handle brackets, metal cabinet, screw heads, metallic overlays, control shafts, etc.), especially any exposed metal parts that offer an electrical return path to the chassis. Any current measured must not exceed 0.5 milli-ampere. Reverse the instrument power cord plug in the outlet and repeat the test.
READING SHOULD NOT BE ABOVE 0.5 mA
LEAKAGE CURRENT TESTER

DEVICE BEING TESTED

TEST ALL EXPOSED METAL SURFACES

ALSO TEST WITH PLUG REVERSED USING AC ADAPTER PLUG AS REQUIRED

EARTH GROUND

ANY MEASUREMENTS NOT WITHIN THE LIMITS SPECIFIED HEREIN INDICATE A POTENTIAL SHOCK HAZARD THAT MUST BE ELIMINATED BEFORE RETURNING THE INSTRUMENT TO THE CUSTOMER OR BEFORE CONNECTING THE ANTENNA OR ACCESSORIES. e. X-Radiation and High Voltage Limits - Because the picture tube is the primary potential source of X-radiation in solid-state TV receivers, it is specially constructed to prohibit X-radiation emissions. For continued X-radiation protection, the replacement picture tube must be the same type as the original. Also, because the picture tube shields and mounting hardware perform an X-radiation protection function, they must be correctly in place. High voltage must be measured each time servic-

2-1

L6115IMP

ing is performed that involves B+, horizontal deflection or high voltage. Correct operation of the Xradiation protection circuits also must be reconfirmed each time they are serviced. (X-radiation protection circuits also may be called "horizontal disable" or "hold down.") Read and apply the high voltage limits and, if the chassis is so equipped, the X-radiation protection circuit specifications given on instrument labels and in the Product Safety & X-Radiation Warning note on the service data chassis schematic. High voltage is maintained within specified limits by close tolerance safety-related components/adjustments in the high-voltage circuit. If high voltage exceeds specified limits, check each component specified on the chassis schematic and take corrective action. 2. Read and comply with all caution and safety-related notes on or inside the receiver cabinet, on the receiver chassis, or on the picture tube. 3. Design Alteration Warning - Do not alter or add to the mechanical or electrical design of this TV receiver. Design alterations and additions, including, but not limited to circuit modifications and the addition of items such as auxiliary audio and/or video output connections, might alter the safety characteristics of this receiver and create a hazard to the user. Any design alterations or additions will void the manufacturer's warranty and may make you, the servicer, responsible for personal injury or property damage resulting therefrom. 4. Picture Tube Implosion Protection Warning The picture tube in this receiver employs integral implosion protection. For continued implosion protection, replace the picture tube only with one of the same type number. Do not remove, install, or otherwise handle the picture tube in any manner without first putting on shatterproof goggles equipped with side shields. People not so equipped must be kept safely away while picture tubes are handled. Keep the picture tube away from your body. Do not handle the picture tube by its neck. Some "in-line" picture tubes are equipped with a permanently attached deflection yoke; because of potential hazard, do not try to remove such "permanently attached" yokes from the picture tube. 5. Hot Chassis Warning a. Some TV receiver chassis are electrically connected directly to one conductor of the AC power cord and maybe safety-serviced without an isolation transformer only if the AC power plug is inserted so that the chassis is connected to the ground side of the AC power source. To confirm that the AC power plug is inserted correctly, with an AC voltmeter, measure between the chassis and a known

earth ground. If a voltage reading in excess of 1.0V is obtained, remove and reinsert the AC power plug in the opposite polarity and again measure the voltage potential between the chassis and a known earth ground. b. Some TV receiver chassis normally have 85V AC(RMS) between chassis and earth ground regardless of the AC plug polarity. This chassis can be safety-serviced only with an isolation transformer inserted in the power line between the receiver and the AC power source, for both personnel and test equipment protection. c. Some TV receiver chassis have a secondary ground system in addition to the main chassis ground. This secondary ground system is not isolated from the AC power line. The two ground systems are electrically separated by insulation material that must not be defeated or altered. 6. Observe original lead dress. Take extra care to assure correct lead dress in the following areas:a. near sharp edges,b. near thermally hot parts-be sure that leads and components do not touch thermally hot parts,c. the AC supply,d. high voltage, and,e. antenna wiring. Always inspect in all areas for pinched, out of place, or frayed wiring. Check AC power cord for damage. 7. Components, parts, and/or wiring that appear to have overheated or are otherwise damaged should be replaced with components, parts, or wiring that meet original specifications. Additionally, determine the cause of overheating and/or damage and, if necessary, take corrective action to remove any potential safety hazard. 8. Product Safety Notice - Some electrical and mechanical parts have special safety-related characteristics which are often not evident from visual inspection, nor can the protection they give necessarily be obtained by replacing them with components rated for higher voltage, wattage, etc.. Parts that have special safety characteristics are identified by a ( # ) on schematics and in parts lists. Use of a substitute replacement that does not have the same safety characteristics as the recommended replacement part might create shock, fire, and/or other hazards. The product's safety is under review continuously and new instructions are issued whenever appropriate. Prior to shipment from the factory, our products are strictly inspected to confirm they comply with the recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced.

2-2

L6115IMP

Precautions during Servicing

A. Parts identified by the ( # ) symbol are critical for safety. Replace only with part number specified. B. In addition to safety, other parts and assemblies are specified for conformance with regulations applying to spurious radiation. These must also be replaced only with specified replacements. Examples: RF converters, RF cables, noise blocking capacitors, and noise blocking filters, etc. C. Use specified internal wiring. Note especially: 1) Wires covered with PVC tubing 2) Double insulated wires 3) High voltage leads D. Use specified insulating materials for hazardous live parts. Note especially: 1) Insulation Tape 2) PVC tubing 3) Spacers 4) Insulators for transistors. E. When replacing AC primary side components (transformers, power cord, etc.), wrap ends of wires securely about the terminals before soldering. F. Observe that the wires do not contact heat producing parts (heatsinks, oxide metal film resistors, fusible resistors, etc.) G. Check that replaced wires do not contact sharp edged or pointed parts. H. When a power cord has been replaced, check that 5~6 kg of force in any direction will not loosen it. I. Also check areas surrounding repaired locations. J. Use care that foreign objects (screws, solder droplets, etc.) do not remain inside the set. K. Crimp type wire connector The power transformer uses crimp type connectors which connect the power cord and the primary side of the transformer. When replacing the transformer, follow these steps carefully and precisely to prevent shock hazards. Replacement procedure 1) Remove the old connector by cutting the wires at a point close to the connector. Important: Do not re-use a connector (discard it). 2) Strip about 15 mm of the insulation from the ends of the wires. If the wires are stranded, twist the strands to avoid frayed conductors.

3) Align the lengths of the wires to be connected. Insert the wires fully into the connector. 4) Use the crimping tool to crimp the metal sleeve at the center position. Be sure to crimp fully to the complete closure of the tool. L. When connecting or disconnecting the internal connectors, first, disconnect the AC plug from the AC supply outlet.

2-3

L6115IMP

Safety Check after Servicing

Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and wires have been returned to original positions. Afterwards, perform the following tests and confirm the specified values in order to verify compliance with safety standards.
Chassis or Secondary Conductor Primary Circuit Terminals d' d

1. Clearance Distance
When replacing primary circuit components, confirm specified clearance distance (d) and (d') between soldered terminals, and between terminals and surrounding metallic parts. (See Fig. 1) Table 1 : Ratings for selected area AC Line Voltage 110 to 130 V Region USA or CANADA Clearance Distance (d) (d') 3.2 mm (0.126 inches)
Exposed Accessible Part Z

Fig. 1

Note: This table is unofficial and for reference only. Be sure to confirm the precise values.

2. Leakage Current Test

Confirm the specified (or lower) leakage current between B (earth ground, power cord plug prongs) and externally exposed accessible parts (RF terminals, antenna terminals, video and audio input and output terminals, microphone jacks, earphone jacks, etc.) is lower than or equal to the specified value in the table below. Measuring Method : (Power ON) Insert load Z between B (earth ground, power cord plug prongs) and exposed accessible parts. Use an AC voltmeter to measure across both terminals of load Z. See Fig. 2 and following table.

1.5k 0.15F

AC Voltmeter (High Impedance)

Earth Ground Power Cord Plug Prongs

Fig. 2

Table 2 : Leakage current ratings for selected areas AC Line Voltage 110 to 130 V Region USA Load Z 0.15F CAP. & 1.5k RES. connected in parallel Leakage Current (i) i0.5mA rms Earth Ground (B) to: Exposed accessible parts

Note: This table is unofficial and for reference only. Be sure to confirm the precise values.

2-4

L6115IMP

STANDARD NOTES FOR SERVICING

Circuit Board Indications
a. The output pin of the 3 pin Regulator ICs is indicated as shown. (2) Remove the flat pack-IC with tweezers while applying the hot air. (3) Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6) (4) Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6)

Top View Out In Input

Bottom View

b. For other ICs, pin 1 and every fifth pin are indicated as shown.

Caution:
1. Do not supply hot air to the chip parts around the flat pack-IC for over 6 seconds because damage to the chip parts may occur. Put masking tape around the flat pack-IC to protect other parts from damage. (Fig. S-1-2) 2. The flat pack-IC on the CBA is affixed with glue, so be careful not to break or damage the foil of each pin or the solder lands under the IC when removing it.

5 Pin 1

10
c. The 1st pin of every male connector is indicated as shown.

Pin 1

CBA

Hot-air Flat Pack-IC Desoldering Machine

How to Remove / Install Flat Pack-IC

1. Removal
With Hot-Air Flat Pack-IC Desoldering Machine: (1) Prepare the hot-air flat pack-IC desoldering machine, then apply hot air to the Flat Pack-IC (about 5 to 6 seconds). (Fig. S-1-1)

Masking Tape Tweezers

Flat Pack-IC

Fig. S-1-2

Fig. S-1-1

3-1

L6115STA

With Soldering Iron: (1) Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3)

soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6) (5) Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6) Note: When using a soldering iron, care must be taken to ensure that the flat pack-IC is not being held by glue. When the flat pack-IC is removed from the CBA, handle it gently because it may be damaged if force is applied.
Hot Air Blower

Flat Pack-IC

Desoldering Braid

Soldering Iron Fig. S-1-3

or

(2) Lift each lead of the flat pack-IC upward one by one, using a sharp pin or wire to which solder will not adhere (iron wire). When heating the pins, use a fine tip soldering iron or a hot air desoldering machine.(Fig. S-1-4)
To Solid Mounting Point

Iron Wire

Soldering Iron

Fig. S-1-5

Sharp Pin Fine Tip Soldering Iron

CBA

Fine Tip Soldering Iron

Fig. S-1-4

(3) Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6) (4) Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6) With Iron Wire: (1) Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3) (2) Affix the wire to a workbench or solid mounting point, as shown in Fig. S-1-5. (3) While heating the pins using a fine tip soldering iron or hot air blower, pull up the wire as the solder melts so as to lift the IC leads from the CBA contact pads as shown in Fig. S-1-5. (4) Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply

Flat Pack-IC Tweezers Fig. S-1-6

3-2

L6115STA

2. Installation
(1) Using desoldering braid, remove the solder from the foil of each pin of the flat pack-IC on the CBA so you can install a replacement flat pack-IC more easily. (2) The "I" mark on the flat pack-IC indicates pin 1. (See Fig. S-1-7.) Be sure this mark matches the 1 on the PCB when positioning for installation. Then pre- solder the four corners of the flat pack-IC. (See Fig. S-1-8.) (3) Solder all pins of the flat pack-IC. Be sure that none of the pins have solder bridges.

Instructions for Handling Semiconductors

Electrostatic breakdown of the semiconductors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work.

1. Ground for Human Body

Be sure to wear a grounding band (1M) that is properly grounded to remove any static electricity that may be charged on the body.

2. Ground for Workbench

Be sure to place a conductive sheet or copper plate with proper grounding (1M) on the workbench or other surface, where the semiconductors are to be placed. Because the static electricity charge on clothing will not escape through the body grounding band, be careful to avoid contacting semiconductors with your clothing.

Example :

<Incorrect>
Pin 1 of the Flat Pack-IC is indicated by a " " mark. Fig. S-1-7

Presolder CBA

<Correct>
Flat Pack-IC CBA Fig. S-1-8

Grounding Band

1M

CBA

1M Conductive Sheet or Copper Plate

3-3

L6115STA

CABINET DISASSEMBLY INSTRUCTIONS

1. Disassembly Flowchart
This flowchart indicates the disassembly steps for the cabinet parts, and the CBA in order to gain access to item(s) to be serviced. When reassembling, follow the steps in reverse order. Bend, route and dress the cables as they were. Caution ! When removing the CRT, be sure to discharge the Anode Lead of the CRT with the CRT Ground Wire before removing the Anode Cap. Note : (1) Order of steps in procedure. When reassembling, follow the steps in reverse order.These numbers are also used as the Identification (location) No. of parts in figures. (2) Parts to be removed or installed. (3) Fig. No. showing procedure of part location (4) Identification of part to be removed, unhooked, unlocked, released, unplugged, unclamped, or desoldered. S=Screw, P=Spring, L=Locking Tab, CN=Connector, *=Unhook, Unlock, Release, Unplug, or Desolder 2(S-2) = two Screws (S-2) (5) Refer to the following "Reference Notes in the Table."

[1] Rear Cabinet

[2] CRT CBA

Reference Notes in the Table

[3] Main CBA
1. Removal of the Rear Cabinet. Remove screws 7(S-1), 1(S-2) and 1(S-4) then slide the Rear Cabinet backward. 2. Removal of the CRT CBA. Disconnect CN1501 then pull the CRT CBA backward. Caution ! Discharge the Anode Lead of the CRT with the CRT Ground Wire before removing the Anode Cap.
Note

[4] CRT

2. Disassembly Method
Removal Step/ Loc. No. Part Fig. No 1,2 4,5 3,5 4 Remove/*unlock/ release/unplug/ unclamp/desolder 7(S-1), 1(S-2), 1(S-4) CN1501 CN571, CN801, CN802 (SRT2223S only), Anode Cap 4(S-3), CN691

3. Removal of the Main CBA. First, disconnect CN571 on the Main CBA. Second, remove Anode Cap. then slide the Main CBA backward. 4. Removal of the CRT. First, disconnect CN691 on the Main CBA. Second, remove screws 4(S-3) then slide the CRT backward.

[1] [2] [3] [4]

Rear Cabinet CRT CBA Main CBA CRT

1 2 3 4

(1)

(2)

(3)

(4)

(5)

4-1

L6550DC

S-1

S-1

S-1 [3] Main CBA

ANT.IN

S-2 S-1 [1] Rear Cabinet S-4

Fig. 1

Fig. 3

[2] CRT CBA

S-3 S-1 S-1 S-1 S-2 S-4 S-3 S-3 S-1 S-1 S-1 S-1 Anode Cap

[1] Rear Cabinet

[4] CRT

S-3

Fig. 2

Fig. 4

4-2

L6550DC

TV Cable Wiring Diagram

SP802 DG691 DEGAUSSING COIL

SP801

CLN802 CLN801 MAIN CBA CN801 CN802

WH301A CN691 FLYBACK TRANSFORMER T571 TU1 TUNER

CN571 AC601 AC CORD FOCUS

WH501A

JK1501 SCREEN WH301B WH501B ANODE CN1501 TO CRT GROUND

Fig. 5

4-3

L6550DC

ELECTRICAL ADJUSTMENT INSTRUCTIONS

General Note: "CBA" is abbreviation for "Circuit Board Assembly". NOTE: Electrical adjustments are required after replacing circuit components and certain mechanical parts. It is important to perform these adjustments only after all repairs and replacements have been completed. Also, do not attempt these adjustments unless the proper equipment is available.

1. DC 120V Adjustment
Purpose: To obtain correct operation. Symptom of Misadjustment: The picture is dark and the unit does not operate correctly. Test Point TP601(+120) TP300(GND) Tape --Adj. Point VR661 M. EQ. DC Voltmeter Mode --Spec. +1200.5V DC. Input ---

Test Equipment Required

1. NTSC Pattern Generator (Color Bar W/White Window, Red Color, Dot Pattern, Gray Scale, Monoscope, Multi-Burst) 2. DC Voltmeter 3. Oscilloscope: Dual-trace with 10:1 probe, V-Range:0.001~50V/Div, F-Range:DC~AC-60MHz 4. Plastic Tip Driver 5. Remote control unit:Part No. N0138UD or N0139UD or N0105UD or N0108UD 6. DC power supply 13.2V/5A

Note:TP601, TP300(GND), VR661 --- Main CBA 1. Connect DC Volt Meter to TP601 and TP300(GND). 2. Adjust VR661 so that the voltage of TP601 becomes +1200.5V DC.

2. Black Strech Control Adjustment

Purpose: To show the fine black color. Symptom of Misadjustment: Black color will not appear correctly. Note: Use Service remote control unit. 1. Enter the Service mode. (See page 5-1) 2. Press " 6 " button on the Service remote control unit. " B-S " is indicated. 3. Press " CH o / p " buttons on the Service remote control unit so that display will change " OFF ", " 0 ", " 1 ", " 2 " and " 3 ". Then choose " B-S OFF ". 4. Press " 6 " button on the Service remote control unit. " B-S*2 " is indicated. 5. Press " CH o / p " buttons on the Service remote control unit so that display will change " 0 " and " 1 ". Then choose " B-S*2 0".

How to make Service remote control unit:

1. Prepare normal remote control unit. (Part No. N0138UD or N0139UD) Remove 3 Screws from the back lid. (Fig. 1-1) 2. Added J1 (Jumper Wire) to the remote control CBA. (Fig. 1-2)

SCREWS

REMOTE CONTROL UNIT

Fig. 1-1

6. Turn the power off and on again. (Main power button on the TV unit.)

J1

REMOTE CONTROL CBA

Fig. 1-2

Notes: 1. The service remote control unit that be made in above method is usable in the electrical adjustment of the following models. SRT2313/2319, SRT2213B/2219B, SRT2227X, SRT2223X, SRT2223B, SRT2232X, SRT2220P SRT4127P 2. The attached remote control unit can not be used as service remote control unit.

5-1

L6550EA

3-1. Setting for 7F and FRENCH data Values

General 1. Enter the Service mode. (See page 5-1) 2. Press " VOL p " button on the Service remote control unit. Display changes " C/D ", " 7F ", " FRENCH ", " ACCESS CODE ", " STEREO ", " VIDEO TONE ", " FM-MODE ", and " V-OUT " cyclically when " VOL p " button is pressed. 7F 1. Press " VOL p " button on the Service remote control unit. Then select 7F display. 2. Press " CH o / p " buttons on the Service remote control unit. Then choose 7F=FF. FRENCH 1. 2. Press " VOL p " button on the Service remote control unit. Then select FRENCH display. Press " CH o / p " buttons on the Service remote control unit. Then choose FRENCH=OFF.

TINT (TNT) 1. Press " MENU " button on the Service remote control unit. Then select " TINT " (TNT) display. 2. Press " CH o / p " buttons on the Service remote control unit so that the value of " TINT " (TNT) becomes 62. V-TINT (V-TNT) 1. Press " MENU " button on the Service remote control unit. Then select " V-TINT " (V-TNT) display. 2. Press " CH o / p " buttons on the Service remote control unit so that the value of " V-TINT " (V-TNT) becomes 59. SHARP (SHARP) 1. Press " MENU " button on the Service remote control unit. Then select " SHARP " (SHARP) display. 2. Press " CH o / p " buttons on the Service remote control unit so that the value of SHARP " (SHARP) becomes 47. Note: BRIGHT data value does not need to be adjusted at this moment.

ACCESS CODE ---- set to ON VIDEO TONE ---- set to ON FM-MODE ---- set to OFF V-OUT ---- set to OFF STEREO ---- set to ON Note: C/D and VCO data values do not need to be adjusted at this moment.

4. Black Level Adjustment

Purpose: Set Black Level Symptom of Misadjustment: If black level is incorrect, Proper brightness can not be obtained by adjusting the Brightness Control. 1. Enter the Service mode. (See page 5-1). 2. Press " MENU " button on the Service remote control unit and select " BRT "mode. (Display changes " BRT ", " CNT ", " CLR ", " TNT ", " V-TINT ", and " SHRAP " cyclically when MENU button is pressed). 3. Press " CH o / p " buttons on the Service remote control unit so that the value of " BRT " becomes 128. 4. Turn the power off and on again. (Main power button on the TV unit.)

3-2. Setting for CONTRAST, COLOR, TINT, V-TINT and SHARP data Values
General 1. Enter the Service mode. (See page 5-1) 2. Press " MENU " button on the Service remote control unit. Display changes " BRIGHT ", " CONTRAST ", " COLOR ", " TINT ", " V-TINT " and " SHARP " cyclically when " MENU " button is pressed. CONTRAST (CNT) 1. Press " MENU " button on the Service remote control unit. Then select " CONTRAST " (CNT) display. 2. Press " CH o / p " buttons on the Service remote control unit so that the value of " CONTRAST " (CNT) becomes 84. COLOR (CLR) 1. Press " MENU " button on the Service remote control unit. Then select " COLOR " (CLR) display. 2. Press " CH o / p " buttons on the Service remote control unit so that the value of " COLOR " (CLR) becomes 58.

5-2

L6550EA

5. V. Size Adjustment
Purpose: To obtain correct vertical width of screen image. Symptom of Misadjustment: If V. Size is incorrect, vertical size of image on the screen may not be properly displayed. Test Point Adj. Point Screen Control CH o / p buttons [ V-S ] Mode M. EQ. Monoscope Mode Input Monoscope Spec. 905%

7. H. Position Adjustment
Purpose: To obtain correct horizontal position of screen image. Symptom of Misadjustment: If H. Position is incorrect, horizontal position of image on the screen may not be properly displayed. Test Point Adj. Point Screen Control CH o / p buttons [ H-P ] Mode M. EQ. Monoscope Mode Input Monoscope Spec. 905%

---

RF

---

RF

Tape --1. 2. 3. 4.

Tape ---

Note: Use service remote control unit. Operate the unit for at least 20 minutes. Enter the Service mode. (See page 5-1) Receive the Monoscope Pattern. Press " 9 " button on the Service remote control unit and select " V-S " mode. (Display changes " V-S " and " V-P " cyclically when " 9 " button is pressed). 5. Press " CH o / p " buttons on the Service remote control unit so that the monoscope pattern will be 905% of display size and the circle is round. 6. Turn the power off and on again. (Main power button on the TV unit.)

Note: Use Service remote control unit 1. Operate the unit for at least 20 minutes. 2. Enter the Service mode. (See page 5-1) 3. Receive the Monoscope Pattern. 4. Press " 8 " button on the remote control unit and select " H-P "mode. 5. Press " CH o / p " buttons on the Service remote control unit so that the monoscope pattern will be 905% of display size and the circle is round. 6. Turn the Power off and on again. (Main power button on the TV unit.)

6. V. Position Adjustment
Purpose: To obtain correct vertical width of screen image. Symptom of misadjustment: If V. Position is incorrect, vertical height of image on the screen may not be properly displayed. Test Point Adj. Point Screen Control CH o / p buttons [ V-P ] Mode M. EQ. Monoscope Mode Input Monoscope Spec. 905%

8. H. Size Adjustment
Purpose: To obtain correct horizontal size of screen image. Symptom of Misadjustment: If H. Size is incorrect, horizontal size of image on the screen may not be properly displayed. Test Point --Tape --Adj. Point VR562 M. EQ. Monoscope Mode RF Input Monoscope Spec. 905%

---

RF

Tape ---

Note: Use Service remote control unit 1. Operate the unit for at least 20 minutes. 2. Enter the Service Mode. (See page 5-1) 3. Receive the Monoscope Pattern. 4. Press " 9 " button on the Service remote control unit and select " V-P "mode. (Display change " V-S " and " V-P " cyclically when " 9 " button is pressed). 5. Press " CH o / p " buttons on the Service remote control unit so that the top and bottom of the monoscope pattern will be equal of each other. 6. Turn the Power off and on again. (Main power button on the TV unit.)

Note: Use Service remote control unit 1. Operate the unit for at least 20 minutes. 2. Receive the Monoscope Pattern. 3. Adjust VR562 so that the monoscope pattern will be 905% of display size and circle is round. 4. Turn the Power off and on again. (Main power button on the TV unit.)

5-3

L6550EA

9. PIN Cushion Adjustment

Purpose: To obtain correct straight vertical line of screen image. Symptom of Misadjustment: If H.Pin cushion is incorrect, vertical line of image on the screen may not be properly displayed. Test Point --Tape --1. 2. 3. 4. Adj. Point VR561 M. EQ. Cross hatch Mode RF Input Cross hatch Spec.

10. Cut-off Adjustment

Purpose: To adjust the beam current of R, G, B, and screen voltage. Symptom of Misadjustment: White color may be reddish, greenish or bluish. Test Point --Tape --Adj. Point Screen-Control CH o / p buttons M. EQ. Pattern Generator Figure
PATTERN GENERATOR

Mode RF

Input Black Raster Spec.

Note: Use Service remote control unit Operate the unit for at least 20 minutes. Receive the Cross hatch Pattern. Adjust VR561 so that the cross hatch pattern will be straight line of display. Turn the Power off and on again. (Main power button on the TV unit.)

See Reference Notes below.

EXT. INPUT

Fig. 2

Note: Screen Control FBT --- Main CBA F.B.T= Fly Back Transformer Use Service remote control unit 1. Degauss the CRT and allow CRT to operate for 20 minutes before starting the alignment. 2. Input the Black Raster Signal from RF Input. 3. Enter the Service mode. (See page 5-1) 4. Press " VOL p " button on the Service remote control unit and select " C/D " mode. (Display changes " C/D ", " 7F ", " FRENCH ", " ACCESS CODE ", " STEREO ", " VIDEO TONE ", " FM-MODE ", and " V-OUT " cyclically when " VOL p " button is pressed.) then press " 1 ". The display will momentarily show " CUT OFF R " (R= Red). Now there should be a horizontal line across the center of the picture tube. If needed gradually turn the screen control on the flyback, clockwise until the horizontal line appears. Adjust the Red Cut off by pressing the " CH o / p " buttons. Proceed to Step 5 when the Red Cut off adjustment is done. 5. Press the " 2 "button. The display will momentarily show " CUT OFF G " (G=Green). Adjust the Green Cut off by pressing the " CH o / p " buttons. Proceed to step 6 when the Green Cut off adjustment is done. 6. Press the " 3 " button. The display will momentarily show " CUT OFF B " (B=Blue). Adjust the Blue cut off by pressing the " CH o / p " buttons. When done with steps 4, 5 and 6 the horizontal line should be pure white if not, then attempt the Cut off adjustment again.

5-4

L6550EA

11. White Balance Adjustment

Purpose: To mix red, green and blue beams correctly for pure white. Symptom of Misadjustment: White becomes bluish or reddish. Test Point Adj. Point CH o / p buttons M. EQ. Pattern Generator, Color analyzer Figure Mode Input White Raster (APL 100%) Spec. See below

Note: Confirm that Cut Off Adj. is correct after this adjustment, and attempt Cut Off Adj. if needed.

12. Sub-Brightness Adjustment

Purpose: To get proper brightness. Symptom of Misadjustment: If Sub-Brightness is incorrect, proper brightness cannot be obtained by adjusting the Brightness Control. Test Point --Tape --Adj. Point CH o / p buttons M. EQ. Pattern Generator Figure Mode RF Input IQW Spec. See below

Screen

RF

Tape

White

Black This bar just visible Fig. 4

Color Analyzer

Fig. 3

Note: Use Service remote control unit 1. Operate the unit more than 20 minutes. 2. Face the unit to east. Degauss the CRT using Degaussing Coil. 3. Input the White Raster (APL 100%). 4. Set the color analyzer to the CHROMA mode and after zero point calibration, bring the optical receptor to the center on the tube surface (CRT). 5. Enter the Service mode. Press " VOL p " button on the Service remote control unit and select " C/D " mode. (Display changes " C/D ", " 7F ", " FRENCH ", " ACCESS CODE ", " STEREO ", " VIDEO TONE ", " FM-MODE ", and " V-OUT " cyclically when " VOL p " button is pressed.) then Press No. 8 button on the Service remote control Unit. 6. Press No. 4 button on the service remote control unit for Red adjustment. Press N0. 5 button on the Service remote control unit for Blue adjustment. 7. In each color mode, Press " CH o / p " button to adjust the values of color. 8. Adjusting Red and Blue color so that the temperature becomes 9200K (x : 286 / y : 294)3%. 9. At this time, Re-check that Horizontal line is white. If not, Re-adjust Cut-off Adjustment until the Horizontal Line becomes pure white. 10. Turn off and on again to return to normal mode. Receive APL 100% white signal and Check Chroma temperatures become 9200K (x : 286 / y : 294)3%.

Note: IQW Setup level --- 7.5 IRE Use Service remote control unit 1. Enter the Service mode. (See page 5-1) Then input IQW signal from RF Input. 2. Press " MENU " button on the Service remote control unit and Select " BRT " mode. (Display changes " BRT ", " CNT ", " CLR ", " TNT ", " V-TINT ", and " SHRAP " cyclically when MENU button is pressed). Press " CH o / p " buttons so that the bar is just visible (See above figure). 3. Turn the power off and on again. (Main power button on the TV unit.)

5-5

L6550EA

13. Focus Adjustment

Purpose: Set the optimum Focus. Symptom of Misadjustment: If Focus Adjustment is incorrect, blurred images are shown on the display. Test Point --Tape --Adj. Point Focus Control M. EQ. Pattern Generator Mode --Input Monoscope Spec. See below

The following 2 adjustments normally are not attempted in the field. Only when replacing the CRT then adjust as a preparation.

14. Purity Adjustment

Purpose: To obtain pure color. Symptom of Misadjustment: If Color Purity Adjustment is incorrect, large areas of color may not be properly displayed. Test Point --Tape --Adj. Point Deflection Yoke Purity Magnet M. EQ. Pattern Generator Figure Mode --Input Red Color Spec. See below.

Note:Focus VR (FBT) - Main CBA FBT=Fly Back Transformer 1. Operate the unit more than 30 minutes 2. Face the unit to the East and Degauss the CRT using Degaussing Coil. 3. Input the Monoscope Pattern. 4. Adjust the Focus Control on the FBT to obtain clear picture.

GREEN

RED

BLUE Fig. 5

1. Set the unit facing east. 2. Operate the unit for over 30 minutes before adjusting. 3. Fully degauss the unit using an external degaussing coil. 4. Loosen the screw on the Deflection Yoke Clamper and pull the Deflection Yoke back away from the screen. (See Fig. 6) 5. Loosen the Ring Lock and adjust the Purity Magnets so that a red field is obtained at the center of the screen. Tighten Ring Lock. (See Fig. 5,6) 6. Slowly push the Deflection Yoke toward bell of CRT and set it where a uniform red field is obtained. 7. Tighten the clamp screw on the Deflection Yoke.

5-6

L6550EA

15. Convergence Adjustment

Purpose: To obtain proper convergence of red, green and blue beams. Symptom of Misadjustment: If Convergence Adjustment is incorrect, the edge of white letters may have color edges. Test Point Adj. Point C.P. Magnet (RB), C.P. Magnet (RB-G), Deflection Yoke M. EQ. Pattern Generator Figures
CRT COIL SCREW PURITY RB RB-G RING LOCK SCREW

Mode

Input Dot Pattern or Crosshatch Spec.

---

---

1. Loosen the Ring Lock and align red with blue dots or Crosshatch at the center of the screen by rotating (RB) C.P. Magnets. (See Fig. 7) 2. Align red / blue with green dots at the center of the screen by rotating (RB-G) C.P. Magnet. (See Fig. 8) 3. Fix the C.P. Magnets by tightening the Ring Lock. 4. Remove the DY Wedges and slightly tilt the Deflection Yoke horizontally and vertically to obtain the best overall convergence. 5. Fix the Deflection Yoke by carefully inserting the DY Wedges between CRT and Deflection Yoke.

Tape ---

See below.

DY WEDGE C.P. MAGNET CLAMPER C.P. MAGNET COIL CLAMPER DEFLECTION YOKE

Fig. 6

C.P. MAGNET (RB)

R G B
C.B. MAGNET (RB-G)

R G
Fig. 7

RB G RB G

Fig. 8

5-7

L6550EA

System Control Block Diagram

BLOCK DIAGRAMS

IC111 TV MICON/VIDEO /AUDIO/CHROMA /DEFLECTION RCV101 RCV-IN 70 KEY-IN1 66 KEY-IN2 69 REMOTE SENSOR KEY SWITCH TO IF/VIDEO BLOCK

INPUT0

+8V

IC151 (MEMORY) CS 7 SCL 6 SDA 5 72 I2C-OPEN 58 SCL 56 SDA

INPUT0 63

Q481

FROM/TO IF/VIDEO BLOCK

AFT AGC

73 AFT 75 AGC-IN

MONO-OUT STEREO-IN VOLUME A-MUTE-H

71 60 62 64

INSEL1 INSEL2 MONO-OUT STEREO-IN VOLUME A-MUTE-H

FROM/TO AUDIO BLOCK

DG-ON-H 74 +5V-CTRL 28 +8V-CTRL 40

P-ON-H PROTECT-1 PROTECT-2 PROTECT-3

79 68 67 76

DG-ON-H +5V-CTRL +8V-CTRL PROTECT-1 PROTECT-2 P-ON-H PROTECT-1 PROTECT-2 PROTECT-3 P-ON-H

FROM/TO POWER SUPPLY BLOCK

FROM/TO CRT/H.V. BLOCK

MAIN CBA

6-1

6-2

L6550BLS

IF/Video Block Diagram

RF/IF SIGNAL
TU1 IF 11

VIDEO SIGNAL
IC31 20 21

AUDIO SIGNAL

SF1 SAW FILTER

(IF SIGNAL PROCESS) VIF AMP VIDEO DET VCO 5

CF31 4.5MHz TRAP CF32 3 EQ AMP 1 WF6 AF AMP VCO F/B 11 7

MAIN CBA

TP301 AGC AGC SCL SDA EXT.CLK 1 4 5 8 WF16 17 RF AGC AFT AMP

4.5MHz FILTER LPF IF AGC DET

FM DET

TU-AUDIO

TO AUDIO BLOCK

Q31

INPUT0 22 16 AGC AFT

FROM/TO SYSTEM CONTROL BLOCK

14

IC111 TV MICON/VIDEO /AUDIO/CHROMA /DEFLECTION 58 SCL 56 SDA 32

X301 3.58MHz 16

VCXO

WF1 26

TUNER

LUMINANCE PROCESS CIRCUIT RGB MATRIX /COLOR CONT CHROMINANCE PROCESS CIRCUIT LPF OSD SW CONTRAST BRIGHTNESS RGB DRIVE /CUT OFF /H.V. BLK 52 51 50

JK701 VIDEO-IN (FRONT) JK704 VIDEO-IN (REAR) WF2

24

LINE

WH301A 5 BLUE 4 GREEN 3 RED

TO CRT/H.V. BLOCK WH301B

14 11 OSD H-SYNC PROCESS CIRCUIT V-SYNC PROCESS CIRCUIT 53 46 45 38 37 ACL H-DRIVE FBP RAMP-OUT V-RAMP-F/B

FROM/TO CRT/H.V. BLOCK

6-3

6-4

L6550BLIF

Audio Block Diagram

AUDIO SIGNAL MAIN CBA
Q411 BUFFER

MTS/SAP AUDIO IC401 SIGNAL PROCESS

FROM IF/VIDEO BLOCK

TU-AUDIO

ATT

5fH TRAP

L-R DEMOD L+R AMP

LPF LPF

VCA

10

11

L-R AMP

14

MATRIX
13

21

STEREO SW PILOT DET PHASE COMP

2 1

STEREO DRIVER

20

STEREO-IN MONO-OUT

FROM/TO SYSTEM CONTROL BLOCK

VCO

F/F

F/F

F/F

22

Q441

X441

SP801 SPEAKER L-CH CN801 SP-L 2 SP-GND 1 IC481 (INPUT SELECT) JK702 AUDIO-IN-(L) (FRONT) JK703 AUDIO-IN-(R) (FRONT) JK704 AUDIO-IN-(L) (REAR) JK704 AUDIO-IN-(R) (REAR)
12 11

+8V IC802 (AUDIO AMP)

5 7

FRONT TUNER (L-CH) DC VOL.

2 3 6 12 13

JK801 HEADPHONE JACK

1 4

(R-CH) FRONT TUNER

SW CTL
9 10

SP802 SPEAKER R-CH CN802 SP-R 2 SP-GND 1

Q825

A-MUTE-H VOLUME INSEL1 INSEL2

FROM SYSTEM CONTROL BLOCK

6-5

6-6

L6550BLA

CRT/H.V. Block Diagram

VIDEO SIGNAL
IC551 V-DEFLECTION CONTROL THERMAL PROTECTION
7

MAIN CBA
WF11 RAMP-OUT Q531 (SWITCHING)

WF12 5
5

DY551 D.Y. VDRIVE HDRIVE

AMP
1

4 WF9 CN571 VR561 PCC VR562 WIDTH 3 1

FROM/TO IF/VIDEO BLOCK

V-RAMP-F/B

PULSE UP
6 3

Q551, H. Q552 CONTROL Q561 (SWITCHING)

WF7 H-DRIVE Q572 H.DRIVE

WF8 T572 Q571 H.OUTPUT

Q532 SWITCHING P-ON-ON

Q553 (SWITCHING)

FROM POWER SUPPLY BLOCK

DEF+B +B T571 F.B.T.

1

FOCUS VR
HV

ANODE

FROM/TO SYSTEM CONTROL BLOCK

PROTECT-1 PROTECT-2 P-ON-H

X-RAY TP591 TP592

5

11 F S

SCREEN VR
8 10

FOCUS SCREEN

TO SYSTEM CONTROL BLOCK

ANODE
3

PROTECT-3

4 7

TP302 15kHz FROM/TO IF/VIDEO BLOCK FBP ACL

WF10 WH501A 3 HEATER 1 +180V

WH501B
3 1

JK1501 7 4 8 6 11 10 9 CN1501 FOCUS SCREEN GND R G B V501 CRT

FROM IF/VIDEO BLOCK

TO WH301A WH301B RED 3 GREEN 4 BLUE 5 TP1501 GND TP1502 BLUE

WF3

Q1512 RED AMP

WF15

WF4 Q1522 GREEN AMP

WF14 Q1532 BLUE AMP WF5 WF13

HEATER GND

CRT CBA

6-7

6-8

L6550BLCRT

Power Supply Block Diagram

CAUTION ! Fixed voltage ( or Auto voltage selectable ) power supply circuit is used in this unit. If Main Fuse (F601) is blown, check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail.
HOT CIRCUIT. BE CAREFUL.

4A/125V

CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 4 A, 125V FUSE. ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MME TYPE DE 4A, 125V.

NOTE : The voltage for parts in hot circuit is measured using hot GND as a common terminal.

HOT
T601
4A/125V

COLD
DEF +B

F601 4A/125V AC601 AC CORD CN691 DG691 DEGAUSSING COIL

L601 LINE FILTER

D605 - D608 BRIDGE RECTIFIER

6 9

TP601 +B

PROTECT-2 (TO PIN 67 OF IC111) +B AL+33V

10

Q671 SWITCHING

Q111 +5V SWITCHING

BACK-UP P-ON+5V

PS691
4 11

Q676 SWITCHING CONTROL

Q321 +9V SWITCHING

AL+9V AL+12V

12

Q601 SWITCHING

14

Q681 +8V SWITCHING

P-ON+8V +8V CTRL (FROM PIN40 OF IC111) PROTECT-1 (TO PIN68 OF IC111) P-ON+5V +5V CTRL (FROM PIN28 OF IC111) P-ON+5V

Q602 LIMITER

13

Q682 +5V SWITCHING

Q683 +5V SWITCHING

4 1

IC601 ERROR VOLTAGE DET

3 2

VR661 Q662 FEED BACK +B ADJ

Q831 SWITCHING P-ON-ON

SWITCHING Q833 P-ON+8V

Q832 SWITCHING P-ON-ON

P-ON+12V

RL601

P-ON+8V

Q675 SWITCHING P-ON-ON

Q696 (SWITCHING) DG-ON-H (FROM PIN74 OF IC111)

P-ON-H (FROM PIN79 OF IC111)

MAIN CBA 6-10 L6550BLP

6-9

SCHEMATIC DIAGRAMS / CBA'S AND TEST POINTS

Standard Notes
Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts that have these special safety characteristics are identified in this manual and its supplements; electrical components having such features are identified by the mark " # " in the schematic diagram and the parts list. Before replacing any of these components, read the parts list in this manual carefully. The use of substitute replacement parts that do not have the same safety characteristics as specified in the parts list may create shock, fire, or other hazards.

Note:
1. 2. 3. 4. 5. Do not use the part number shown on these drawings for ordering. The correct part number is shown in the parts list, and may be slightly different or amended since these drawings were prepared. All resistance values are indicated in ohms (K=103, M=106). Resistor wattages are 1/4W or 1/6W unless otherwise specified. All capacitance values are indicated in F (P=10-6F). All voltages are DC voltages unless otherwise specified.

Note of Capacitors:
ML --- Mylar Cap. B --- 10% PP --- Metallized Film Cap. SC --- Semiconductor Cap. L --- Low Leakage type

Temperature Characteristics of Capacitors are noted with the following:

CH --- 060ppm/C CSL --- +350~-1000ppm/C

Tolerance of Capacitors are noted with the following:

Z --- +80~-20%

Note of Resistors:
CEM --- Cement Res. MTL --- Metal Res. F --- Fuse Res.

Capacitors and transistors are represented by the following symbols.

CBA Symbols
(Top View) (Bottom View) + Electrolytic Capacitor

Schematic Diagram Symbols

Digital Transistor

(Bottom View)

Transistor or Digital Transistor

E C B (Top View)

(Top View)

NPN Transistor
ECB ECB

PNP Transistor

(Top View)

(Top View)

NPN Digital Transistor

ECB ECB

PNP Digital Transistor

7-1

L13SC

LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWING PAGES:
1. CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE_A,_V FUSE. ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MME TYPE DE_A,_V. 2. CAUTION: Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F601) is blown, first check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail. 3. Note: (1) Do not use the part number shown on the drawings for ordering. The correct part number is shown in the parts list, and may be slightly different or amended since the drawings were prepared. (2) To maintain original function and reliability of repaired units, use only original replacement parts which are listed with their part numbers in the parts list section of the service manual. 4. Wire Connectors (1) Prefix symbol "CN" means "connector" (can disconnect and reconnect). (2) Prefix symbol "CL" means "wire-solder holes of the PCB" (wire is soldered directly). 5. Note: Mark "I" is a leadless (chip) component. 6. Voltage indications on the schematics are as shown below: Plug the TV power cord into a standard AC outlet.:

1 5.0 (3.0) Voltage

3 5.0 (3.0) Power on mode Power off mode Unit: Volts

Indicates that the voltage is not consistent here.

7. How to read converged lines

1-D3 Distinction Area Line Number (1 to 3 digits) Examples: 1. "1-D3" means that line number "1" goes to area "D3". 2. "1-B1" means that line number "1" goes to area "B1". 3 AREA D3 2 1 A
8. Test Point Information

1-B1 AREA B1 1-D3 B C D

: Indicates a test point with a jumper wire across a hole in the PCB. : Used to indicate a test point with a component lead on foil side. : Used to indicate a test point with no test pin. : Used to indicate a test point with a test pin.

7-2

L13SC

Main 1/4 Schematic Diagram

VIDEO SIGNAL

A4

B4

C4

D4

E4

F4

MAIN 1/4 Ref No.

Position

ICS C-2 IC111 A-3 IC151 TRANSISTORS Q111 D-1 Q321 E-2 Q361 D-4

A3

B3

C3

D3

E3

F3

A2

B2

C2

D2

E2

F2

A1

B1

C1

D1

E1

F1

7-3

7-4

L6550SCM1

Main 2/4 Schematic Diagram

VIDEO SIGNAL AUDIO SIGNAL

G4

H4

I4

J4

K4

L4

MAIN 2/4 Ref No. ICS

Position

G3

H3

I3

J3

K3

L3

H-3 IC401 H-1 IC481 J-4 IC802 TRANSISTORS I-3 Q411 I-4 Q441 K-4 Q481 J-3 Q825 K-2 Q831 K-1 Q832 K-2 Q833 CONNECTORS CN801 K-1 CN802 K-1

G2

H2

I2

J2

K2

L2

G1

H1

I1

J1

K1

L1

7-5

7-6

L6550SCM2

Main 3/4 Schematic Diagram

IF SIGNAL VIDEO SIGNAL AUDIO SIGNAL
CAUTION ! Fixed voltage ( or Auto voltage selectable ) power supply circuit is used in this unit. If Main Fuse (F601) is blown, check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail. NOTE : The voltage for parts in hot circuit is measured using hot GND as a common terminal.
CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 4A, 125V FUSE. ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MME TYPE DE 4A, 125V.

4A/125V

M4

N4

O4

P4

Q4

R4

MAIN 3/4 Ref No. ICS

Position

M3

N3

O3

P3

Q3

R3

M2

N2

O2

P2

Q2

R2

P-3 IC31 O-1 IC601 TRANSISTORS P-4 Q31 P-2 Q601 P-1 Q602 N-1 Q641 O-1 Q662 N-2 Q671 Q675 N-1 N-1 Q676 M-1 Q681 M-1 Q682 M-1 Q683 O-2 Q696 CONNECTOR CN691 Q-2 TEST POINT N-4 TP301 VARIABLE RESISTOR VR661 O-1

M1

N1

O1

P1

Q1

1 NOTE: *The Capacitor ( C643 ) is either type A or type B. These two types are exchangeable and can be equally used whichever the model is . The difference between type A and type B is shown in the table below. C643 Type A Type B 0.01/250V 4700P/250V C642 0.01/250V Not Used JS642 Not Used WIRE

R1

7-7

7-8

L6550SCM3

Main 4/4 & CRT Schematic Diagram

MAIN 4/4 Ref No. Position Ref No. Position TRANSISTORS T-2 Q572 CONNECTORS T-3 CN571 WH301A V-2 WH501A V-3 TEST POINTS U-2 TP300 TP302 V-2 TP591 U-2 Ref No. Position TEST POINTS U-2 TP592 U-2 TP601 VARIABLE RESISTORS VR561 U-3 VR562 U-3 CRT Ref No. Position TRANSISTORS W-2 Q1512 W-2 Q1522 W-2 Q1532 CONNECTORS CN1501 X-2 WH301B V-2 WH501B V-3 TEST POINTS X-2 TP1501 TP1502 W-3

IC S-3 IC551 TRANSISTORS S-2 Q531 S-2 Q532 Q551 T-3 Q552 T-3 U-2 Q553 Q561 U-3 Q571 U-2

VIDEO SIGNAL

S3

T3

U3

V3

W3

X3

S2

T2

U2

V2

W2

X2

S1

T1

U1

V1

W1

X1

7-9

7-10

L6550SCM4

Main CBA Top View

CAUTION: FOR CONTINUED PROTECTION AGAINST RISK BECAUSE A HOT CHASSIS GROUND IS PRESENT IN THE POWER MAIN CBA OF FIRE, REPLACE ONLY WITH SAME TYPE 4A, 125V FUSE. Ref No. Position SUPPLY CIRCUIT, AN ISOLATION TRANSFORMER MUST BE USED. CAUTION ! ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE ICS 4A/125V MME TYPE DE 4A, 125V. ALSO, IN ORDER TO HAVE THE ABILITY TO INCREASE THE INPUT Fixed voltage ( or Auto voltage selectable ) power supply circuit is used in this unit. B-1 IC31 If Main Fuse (F601) is blown, check to see that all components in the power SLOWLY, WHEN TROUBLESHOOTING THIS TYPE POWER SUPPLY NOTE : D-2 IC111 supply circuit are not defective before you connect the AC plug to the AC power supply. The voltage for parts in hot circuit is measured CIRCUIT, A VARIABLE ISOLATION TRANSFORMER IS REQUIRED. E-2 IC151 Otherwise it may cause some components in the power supply circuit to fail. using hot GND as a common terminal. D-3 IC401 E-3 IC481 B-2 IC551 C-4 IC601 E-4 IC802 TRANSISTORS Q31 C-1 Q111 D-2 Q321 C-1 Q361 C-2 Q411 E-2 TP601 Q441 D-3 +B Q481 F-2 B-2 Q531 A-2 Q532 FOCUS-VR B-2 Q551 (UPPER SIDE) B-2 Q552 B-2 Q553 C-2 Q561 B-4 Q571 C-3 Q572 B-5 SCREEN-VR Q601 (LOWER SIDE) B-5 Q602 D-4 Q641 D-4 Q662 D-4 Q671 D-4 Q675 D-4 Q676 D-2 Q681 D-3 Q682 TP302 D-2 Q683 15kHz D-4 Q696 D-4 Q825 D-3 Q831 D-3 Q832 E-4 Q833 CONNECTORS B-3 CN571 D-5 CN691 E-1 CN801 E-4 CN802 VR661 +B ADJ WH301A C-2 WH501A A-3 TEST POINTS A-1 TP300 VR561 A-1 TP301 PCC TP302 A-3 TP591 A-3 VR562 TP592 A-3 WIDTH A-4 TP601 TP300 VARIABLE RESISTOR GND B-2 VR561 TP301 B-2 VR562 AGC VR661 B-2

7-11

7-12

BL6600F01012-1

Main CBA Bottom View

CAUTION ! Fixed voltage ( or Auto voltage selectable ) power supply circuit is used in this unit. If Main Fuse (F601) is blown, check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail. 4A/125V
CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 4A, 125V FUSE. ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MME TYPE DE 4A, 125V.

BECAUSE A HOT CHASSIS GROUND IS PRESENT IN THE POWER SUPPLY CIRCUIT, AN ISOLATION TRANSFORMER MUST BE USED. ALSO, IN ORDER TO HAVE THE ABILITY TO INCREASE THE INPUT SLOWLY, WHEN TROUBLESHOOTING THIS TYPE POWER SUPPLY CIRCUIT, A VARIABLE ISOLATION TRANSFORMER IS REQUIRED.

NOTE : The voltage for parts in hot circuit is measured using hot GND as a common terminal.

WF7 Q572 Collector WF8 Q571 Base WF9 PIN 1 OF CN571 WF12 PIN 4 OF CN571 WF10 PIN 3 OF WH501A

WF11 PIN 7 OF IC551

WF6 PIN 11 OF IC31

WF2 PIN 14 OF IC111 WF1 PIN 26 OF IC111

WF16 PIN 8 OF TU1

7-13

7-14

BL6600F01012-1

CRT CBA Top View

CRT CBA Ref No. Position TRANSISTORS Q1512 B-1 B-1 Q1522 A-1 Q1532 CONNECTORS CN1501 A-2 WH301B B-1 WH501B A-1 TEST POINTS A-2 TP1501 TP1502 B-1

CRT CBA Bottom View

WF14 Q1522 Collector

TP1501 GND

WF4 Q1522 Base

WF3 Q1512 Base

WF15 Q1512 Collector

WF13 WF5 Q1532 Q1532 Collector Base

TP1502 BLUE

7-15

7-16

BL6600F01012-2

WAVEFORMS
Input: NTSC Color Bar Signal (with 1kHz Audio Signal) INITIAL POSITION: Unplug unit from AC outlet for at least 5 minutes. reconnect to AC outlet and then turn power on. (Brightness---Center Color---Center Tint --- Center Contrast---Approx 70%)

WF1 ~ WF16 = Waveforms to be observed at Waveform check points. (Shown in Schematic Diagram.)

GND

GND GND

WF1

1DIV: 0.5V 20sec IC 111 Pin 26

WF5

1DIV: 2V 20sec Q 1532 Base

WF9

1DIV: 200V 20sec CN 571 Pin 1

WF13 1DIV: 20V 20sec Q1532 Collector

GND

WF2

1DIV: 0.5V 20sec IC 111 Pin 14

WF6

1DIV: 0.2V 20msec IC 31 Pin 11

WF10 1DIV: 5V 20sec WH501A Pin 3

WF14 1DIV: 20V 20sec Q 1522 Collector

GND

GND

WF3

1DIV: 2V 20sec Q1512 Base

WF7

1DIV: 10V 20sec Q 572 Collector

WF11 1DIV: 2V 5msec IC 551 Pin 7

WF15 1DIV: 20V 20sec Q 1512 Collector

GND
10 V 5 ms

WF4

1DIV: 2V 20sec Q 1522 Base

8-1

WF8

1DIV: 5V 20sec Q 571 Base

WF12 1DIV: 10V 5msec CN 571 Pin 4

8-2

WF16 1DIV: 0.2V 20sec TU 1 Pin 8

L6600WF

WIRING DIAGRAM
SP801 SPEAKER L-CH CLN801 CN801 1 SP-L 2 SP-GND

SP802 SPEAKER R-CH ANODE

CLN802

CN802 1 SP-R 2 SP-GND

TU1 TUNER UNIT V501 CRT CN691

1 2

MAIN CBA BL6600F01012-1

GND CN1501 FOCUS SCREEN WH301B BLUE GREEN RED GND +8V WH301A BLUE GREEN RED GND +8V T571 FBT

5 4 3 2 1

CLN301

5 4 3 2 1

CRT CBA BL6600F01012-2

WH501B HEATER 3 GND 2 +180V 1

CLN501

WH501A 3 HEATER 2 GND 1 +180V

DY571 D.Y. HD VD

CN571 1 2 3 4 5

AC601

9-1

L6550WI

IC PIN FUNCTIONS
IC111(TV Micro Computer)
Pin No. 1 2 3 4 5 6 7 8 9 Signal Name GND N.U. N.U. N.U. GND VCC N.U. FILT HLF GND Not Used Not Used Not Used GND AL+5V Not Used FILT Filter for CCD VHOLD Input for Video Signal RESET RESET Signal Output Composite Signal Output GND 3.58MHz Crystal CHROMINANCE APC Micro controller Control Voltage Output Not Used Not Used Not Used VCC (GND) Composite Signal Input 2 Not Used Composite Signal Input 1 Not Used 5.7V Output Not Used Not Used DC 8.7V Input Clock Output 3.58MHz Not Used Not Used 59 N.U. 60 STEREO-IN 61 N.U. 62 VOLUME 63 INPUTO 64 A-MUTE-H 65 N.U. 66 KEY-IN 1 67 PROTECT-2 68 PROTECT-1 69 KEY-IN 2 70 RCV-IN 56 SDA 57 N.U. 58 SCL Function Pin No. Signal Name Not Used Not Used V Ramp Feed Back Vertical Output V Ramp OSC Capacitor DC 8.7V Output Not Used H Vco Feed Back Horizontal AFC Filter GND Flyback Pulse Input H Pulse Output Vcc Vcc Vcc Red Output Green Output Blue Output IB-Input Not Used Not Used I2C-BUS Controller Interface (Data) Not Used I2C-BUS Controller Interface (Clock) (GND) STEREO-IN Not Used Volume EXT-H Audio Mute Not Used Key Input 1 (Main) Power Supply Protection Power Supply Protection Key Input 2 (Main) Input For Remote Control Function

35 N.U. 36 N.U. 37 V RAMP F/B 38 V RAMP OUT 39 V RAMP CAP 40 8.7 VREG OUT 41 N.U. 42 H VCO F/B 43 AFC FILT 44 GND 45 FBP IN 46 H-OUT 47 VCC 48 VCC 49 VCC 50 R OUT 51 G OUT 52 B OUT 53 ACL 54 N.U. 55 N.U.

10 VHOLD 11 CVIN 12 RESET 13 MCU RESET OUT

14 Y-SW OUT 15 GND 16 3.58 X'TAL 17 C-APC 18 MCU 5.7REG OUT

19 N.U. 20 N.U. 21 N.U. 22 VCC 23 N.U. 24 CVBS IN2 25 N.U. 26 CVBS IN1 27 N.U. 28 5.7V REG OUT 29 N.U. 30 N.U. 31 V REG VCC 32 FSC OUT 33 N.U. 34 N.U.

10-1

L6601PIN

Pin No.

Signal Name

Function MONO-OUT White Balance Adjustment Judgement AFT Voltage Input Degaussing Coil Control AGC Voltage Input Power Supply Protection Not Used Switching IF IC VCO Output for P-ON-H Not Used

71 MONO-OUT 72 I2C OPEN 73 AFT 74 DG-ON-H 75 AGC 76 PROTECT 3 77 N.U. 78 FM-SW 79 P-ON-H 80 N.U.

10-2

L6601PIN

EXPLODED VIEWS
Cabinet
SHINWHA TAPE SGT-730 (BLACK) V501-1 L2 L2 Details for DY551 and surrounding parts L2 SHINWHA TAPE SGT-730 (WHITE) A5

DY551

L4 L3

V501-2 B2 B3 Scotch Tape #880 CLN551 B5 L2

CLN801

DY551 A6 B2 CRT CBA B2 DG691 B1 B3

L2

L1 B4 SP801

L2 B5

L2

L1 B4 PB1

A4

B3 B3 Scotch Tape #880 V501 CLN802 B2 L1 B4 B3 SP802 AC601 L1 L1 B1 L1 B2

MAIN CBA

See Electrical Parts List for parts with this mark.

A2

A1

11-1

11-2

L6550CEX

Packing
S2

A4

S6

S2

S4

S3

X2

X3

X4

X1

S1 S5

11-3

L6550PEX

MECHANICAL PARTS LIST

PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTE: Parts that are not assigned part numbers (---------) are not available.
Ref. No.
A1 A2 A4 A5# A6 B1 B2 B3# B4 B5 CLN551 CLN801 SP801 CLN802 SP802 DG691# # L1 L2 L3 L4 PB1#

Ref. No.
S5 S6# X1 X2# X3 X4

Description
SERIAL NO. LABEL L6550UA HOLD PAD L1440JL

Part No.
---------0EM406682 Z325350 0EMN02091 N0136UD N0110UD XB0M451GH001 XB0M451T0001 XB0M451MS002 XB0M451HU002 XB0M451HU003

ACCESSORIES
POLYETHYLENE BAG F8626B5 OWNER'S MANUAL L6550UA:ENGLISH/SPANISH REMOTE CONTROL 130/ERC001/N0136UD or REMOTE CONTROL 130/ERC001/N0110UD DRY BATTERY R6P UM3 or DRY BATTERY R6P/2S or DRY BATTERY(SUNRISE) R6SSE/2S or DRY BATTERY R6P(AR)2PX or DRY BATTERY R6P(AR)2P X ICI

Description
FRONT CABINET L6240UA CONTROL PLATE L6240UA REAR CABINET L6550UA RATING LABEL L6550UA POP LABEL L6200UA TENSION SPRING B0080B0:EM40808 CRT SCREW L6240UA DEGAUSS HOLDER L1200UA SPEAKER HOLDER L1200UA CLOTH L9800UA:95X15XT:0.5 WIRE CRT GND WX1L6240-005 WIRE ASSEMBLY SPEAKER WIRE(180MM) SPEAKER S08F02B or SPEAKER J-F097-C5 WIRE ASSEMBLY SPEAKER WIRE(180MM) SPEAKER S08F02B or SPEAKER J-F097-C5 DEGAUSSING COIL F-L124V or DEGAUSSING COIL AVDG144 SCREW, P-TIGHT 3X12 BIND HEAD+ SCREW, P-TIGHT 4X18 BIND HEAD + SCREW TAPPING M4X14 SCREW, P-TIGHT 3X10 BIND HEAD+ CHASSIS NO. LABEL L6550UA

Part No.
0EM000629 0EM201571 0EM101233 ------------------26WH006 0EM406916 0EM405869 0EM405691 0EM405041 WX1L6240-005 WX1L9800-001 DSD0808XQ010 DSD0808DCP01 WX1L1131-001 DSD0808XQ010 DSD0808DCP01 LLBH00ZTM048 LLBH00ZWR047 GBMP3120 GBMP4180 DBU14140 GBKP3100 ----------

Table 1 (V501 and DY551 Combination)

Note 1: Purity and Convergence Adjustments must be performed following CRT replacement. Refer to Electrical Adjustment Instructions. Note 2: Please confirm CRT Type No. on the CRT Warning Label which is located on the CRT. Then See the Table 1 for V501 and DY551 combination chart. Please refer this CRT, Deflection Yoke combination chart for parts order.
DY551: Deflection Yoke Part No.
LLBY00ZQS016 LLBY00ZGS007

V501: CRT Type No.

CRT A59KPR84X CRT A59KYL220X

V501: CRT Part No.

TCRT190SM029 TCRT190GS040

CRT Warning Label Location

Note: 1. V501 (CRT) HAS COUPLE OF SUBSTITUTIONAL PARTS AND EACH PARTS ALSO HAS MATCHING COMBINATION WITH DY551. PLEASE SEE TABLE 1 FOR DETAILS OF MATCHING COMBINATION. 2. DY551 (DEFLECTION YOKE) HAS MATCHING COMBINATION WITH V501. PLEASE SEE TABLE 1 FOR DETAILS OF MATCHING COMBINATION.

CRT Type No.

CRT Warning Label

CRT TYPE A
DY551# V501# V501-1 V501-2 DEFLECTION YOKE CDY-F2518F CRT A59KPR84X PCM JH88DTA WEDGE FT-00110W or WEDGE DB25SR LLBY00ZQS016 TCRT190SM029 XM04000BV010 XV10000T4001 XV10000D9001

CRT TYPE B
DY551# V501# V501-1 V501-2 DEFLECTION YOKE 6150Z-1030X CRT A59KYL220X PCM JH88DTA WEDGE FT-00110W or WEDGE DB25SR LLBY00ZGS007 TCRT190GS040 XM04000BV010 XV10000T4001 XV10000D9001

CRT

PACKING
S1 S2 S3 S4 CARTON L6550UA STYROFOAM TOP ASSEMBLY L6240UA STYROFOAM BOTTOM ASSEMBLY L6240UA SET SHEET PCEC:003502019816 0EM407900 0EM406989 0EM406990 0EM403887

20030318

12-1

L6550CA

ELECTRICAL PARTS LIST

PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTES: 1. Parts that are not assigned part numbers (---------) are not available. 2. Tolerance of Capacitors and Resistors are noted with the following symbols. C.....0.25% G.....2% M.....20% D.....0.5% J......5% N.....30% F.....1% K.....10% Z.....+80/-20%
C116 C117 C119 C120 C121 C132 C133 C151 C152 C153

Ref. No.
C57 C58 C111 C112 C113 C114 C115

Description
FILM CAP.(P) 0.047F/50V J or FILM CAP.(P) 0.047F/50V J FILM CAP.(P) 0.033F/50V J or FILM CAP.(P) 0.033F/50V J ELECTROLYTIC CAP. 47F/16V M or ELECTROLYTIC CAP. 47F/16V M ELECTROLYTIC CAP. 4.7F/50V M or ELECTROLYTIC CAP. 4.7F/50V M CERAMIC CAP.(AX) F Z 0.1F/50V or CERAMIC CAP.(AX) F Z 0.1F/50V FILM CAP.(P) 0.001F/50V J or FILM CAP.(P) 0.001F/50V J ELECTROLYTIC CAP. 0.1F/50V M or ELECTROLYTIC CAP. 0.1F/50V M or ELECTROLYTIC CAP. 0.1F/50V M CERAMIC CAP.(AX) B K 220pF/50V CERAMIC CAP.(AX) Y K 0.01F/16V ELECTROLYTIC CAP. 100F/10V M or ELECTROLYTIC CAP. 100F/10V M CERAMIC CAP.(AX) F Z 0.01F/25V CERAMIC CAP.(AX) X K 1200pF/16V CERAMIC CAP.(AX) F Z 0.1F/50V or CERAMIC CAP.(AX) F Z 0.1F/50V CERAMIC CAP.(AX) F Z 0.01F/25V CERAMIC CAP.(AX) F Z 0.01F/25V CERAMIC CAP.(AX) B K 220pF/50V CERAMIC CAP.(AX) B K 220pF/50V ELECTROLYTIC CAP. 47F/16V M or ELECTROLYTIC CAP. 47F/16V M CERAMIC CAP.(AX) F Z 0.1F/50V or CERAMIC CAP.(AX) F Z 0.1F/50V CERAMIC CAP.(AX) CH J 120pF/50V ELECTROLYTIC CAP. 1F/50V M or ELECTROLYTIC CAP. 1F/50V M or ELECTROLYTIC CAP. 1F/50V M

Part No.
CMA1JJS00473 CA1J473MS029 CMA1JJS00333 CA1J333MS029 CE1CMASTL470 CE1CMASDL470 CE1JMASTL4R7 CE1JMASDL4R7 CA1J104TU014 CCA1JZT0F104 CMA1JJS00102 CA1J102MS029 CE1JMASTLR10 CE1JMASDLR10 CE1JMASDL0R1 CCA1JKT0B221 CDA1CKT0Y103 CE1AMASTL101 CE1AMASDL101 CDA1EZT0F103 CDA1CKT0X122 CA1J104TU014 CCA1JZT0F104 CDA1EZT0F103 CDA1EZT0F103 CCA1JKT0B221 CCA1JKT0B221 CE1CMASTL470 CE1CMASDL470 CA1J104TU014 CCA1JZT0F104 CA1J121TU008 CE1JMASTL1R0 CE1JMASDL1R0 CE1JMASDL010 CA1J153TU011 CE1AMASTL101 CE1AMASDL101 CE1JMASTLR47 CE1JMASDLR47 CE1JMASTLR47 CE1JMASDLR47 CE1JMASTL100 CE1JMASDL100 CCA1JKT0B221 CE1JMASTL100 CE1JMASDL100 CDA1EZT0F103 CMA1JJS00474 CA1J474MS029 CA1J103TU011 CE1JMASTL1R0 CE1JMASDL1R0 CE1JMASDL010 CA1J103TU011 CE1AMZNTL222 CE1AMZNDL222

MMA-401 CBA
Ref. No.
MMA-401 CBA Consists of the following MAIN CBA CRT CBA ---------------------------

Description

Part No.
0ESA05259

MAIN CBA
Ref. No. Description
MAIN CBA Consists of the following

C155

Part No.
------------

C156 C301

CAPACITORS
C1 C2 C3 C31 C32 C34 C35 C36 C37 C38 C41 C51 C52 C53 C54 C55 C56 CERAMIC CAP.(AX) F Z 0.01F/25V ELECTROLYTIC CAP. 100F/10V M or ELECTROLYTIC CAP. 100F/10V M ELECTROLYTIC CAP. 4.7F/50V M or ELECTROLYTIC CAP. 4.7F/50V M ELECTROLYTIC CAP. 100F/10V M or ELECTROLYTIC CAP. 100F/10V M CERAMIC CAP.(AX) F Z 0.01F/25V ELECTROLYTIC CAP. 0.47F/50V M or ELECTROLYTIC CAP. 0.47F/50V M CERAMIC CAP.(AX) CH J 56pF/50V CERAMIC CAP.(AX) B K 100pF/50V CERAMIC CAP.(AX) F Z 0.1F/50V or CERAMIC CAP.(AX) F Z 0.1F/50V ELECTROLYTIC CAP. 10F/50V M or ELECTROLYTIC CAP. 10F/50V M ELECTROLYTIC CAP. 0.47F/50V M or ELECTROLYTIC CAP. 0.47F/50V M CERAMIC CAP.(AX) B K 1000pF/50V CERAMIC CAP.(AX) F Z 0.01F/25V ELECTROLYTIC CAP. 100F/10V M or ELECTROLYTIC CAP. 100F/10V M CERAMIC CAP.(AX) B K 0.01F/50V CERAMIC CAP.(AX) F Z 0.01F/25V PCB JUMPER D0.6-P5.0 CDA1EZT0F103 CE1AMASTL101 CE1AMASDL101 CE1JMASTL4R7 CE1JMASDL4R7 CE1AMASTL101 CE1AMASDL101 CDA1EZT0F103 CE1JMASTLR47 CE1JMASDLR47 CA1J560TU008 CCA1JKT0B101 CA1J104TU014 CCA1JZT0F104 CE1JMASTL100 CE1JMASDL100 CE1JMASTLR47 CE1JMASDLR47 CCA1JKT0B102 CDA1EZT0F103 CE1AMASTL101 CE1AMASDL101 CA1J103TU011 CDA1EZT0F103 JW5.0T

C302

C303 C306 C308 C322 C324 C325 C328 C329 C330 C341 C342

CERAMIC CAP.(AX) B K 0.015F/50V ELECTROLYTIC CAP. 100F/10V M or ELECTROLYTIC CAP. 100F/10V M ELECTROLYTIC CAP. 0.47F/50V M or ELECTROLYTIC CAP. 0.47F/50V M ELECTROLYTIC CAP. 0.47F/50V M or ELECTROLYTIC CAP. 0.47F/50V M ELECTROLYTIC CAP. 10F/50V M or ELECTROLYTIC CAP. 10F/50V M CERAMIC CAP.(AX) B K 220pF/50V ELECTROLYTIC CAP. 10F/50V M or ELECTROLYTIC CAP. 10F/50V M CERAMIC CAP.(AX) F Z 0.01F/25V STACKED FILM CAP. 0.47F/50V J or FILM CAP.(P) 0.47F/50V J CERAMIC CAP.(AX) B K 0.01F/50V ELECTROLYTIC CAP. 1F/50V M or ELECTROLYTIC CAP. 1F/50V M or ELECTROLYTIC CAP. 1F/50V M

C343 C345

CERAMIC CAP.(AX) B K 0.01F/50V ELECTROLYTIC CAP. 2200F/10V M or ELECTROLYTIC CAP. 2200F/10V M

20030318

13-1

L6550EL

Ref. No.
C347 C349 C353

Description
ELECTROLYTIC CAP. 470F/10V M or ELECTROLYTIC CAP. 470F/10V M ELECTROLYTIC CAP. 470F/10V M or ELECTROLYTIC CAP. 470F/10V M ELECTROLYTIC CAP. 1F/50V M or ELECTROLYTIC CAP. 1F/50V M or ELECTROLYTIC CAP. 1F/50V M

Part No.
CE1AMASTL471 CE1AMASDL471 CE1AMASTL471 CE1AMASDL471 CE1JMASTL1R0 CE1JMASDL1R0 CE1JMASDL010 CDA1CKT0X472 CMA1JJS00224 CA1J224MS029 CE1JMASTL1R0 CE1JMASDL1R0 CE1JMASDL010 CE1JMASTLR10 CE1JMASDLR10 CE1JMASDL0R1 CE1CMASTL470 CE1CMASDL470 CA1J104TU014 CCA1JZT0F104 CE1JMASTL1R0 CE1JMASDL1R0 CE1JMASDL010 CDA1CKT0X472 CDA1CKT0X472 JW5.0T JW5.0T CE1JMASTL2R2 CE1JMASDL2R2 CE1JMASTL100 CE1JMASDL100 CDA1CKT0X272 CMA1JJS00104 CA1J104MS029 CDA1EZT0F103 CDA1EZT0F103 CE1JMASTL100 CE1JMASDL100 CE1JMASTL1R0 CE1JMASDL1R0 CE1JMASDL010 CE1JMASTL3R3 CE1JMASDL3R3 CE1AMASTL101 CE1AMASDL101 CE1GMASTL470 CE1GMASDL470 CMA1JJS00104 CA1J104MS029 CE1JMASLL1R5 CE1EMZNTL102 CE1EMZPDL102 CE1EMZADL102 CE1GMZNTL471 CE1GMZADL471 CE1GMZNDL471 JW5.0T CT2A105MS065 CMA1JJS00104 CA1J104MS029 CE1GMASTL470

Ref. No.
C562

Description
ELECTROLYTIC CAP. 47F/35V M ELECTROLYTIC CAP. 470F/25V M or ELECTROLYTIC CAP. 470F/25V M or ELECTROLYTIC CAP. 470F/25V M

Part No.
CE1GMASDL470 CE1EMZNTL471 CE1EMZNDL471 CE1EMZADL471 CMA1JJS00104 CA1J104MS029 CA3C182VC010 CT3C182MS039 CBH3CJQ00182 CT3C182F7002 CA2D564VC012 CT2E564MS041 CT2D564F7001 CE2EMASDL100 CE1GMASTL470 CE1GMASDL470 CMA1JJS00103 CA1J103MS029 CA3C183VC010 CT3C183MS039 CBH3CJQ00183 CA2D333VC013 CBP2DKD00333 CT2D333F7001 CE2CMASTL1R0 CE2CMASDL1R0 CCD2JKS0B221 CE1JMASTL100 CE1JMASDL100 CT2E104MS037 CT2E104DC011 CT2E104HJE06 CCA1JKT0B471 CCD2JZP0F103 CCD2EZA0F103 CCD2JZP0F103 CCD2EZA0F103 CCD3DKD0B102 CCD3DKP0B102 CA3D102PAN04 CA2D221NC088 CA2D221S6003 CMA1JJS00562 CA1J562MS029 CMA1JJS00563 CA1J563MS029 CDA1CKT0X272 CCA1JKT0B101 CMA1JJS00104 CA1J104MS029 CCA1JKT0B331 CMA1JJS00104 CA1J104MS029 CCG2EMA0F103 CCG2EMP0F103 CCG2HMN0F103 CCG2EMA0F103 CCG2EMP0F103 CCG2HMN0F103

C565 C567# # # # C571# # # C574# C577 C578 C580# # # C582# # # C584 C585 C591 C601# # # C603 C605 C606 C609

FILM CAP.(P) 0.1F/50V J or FILM CAP.(P) 0.1F/50V J PP CAP. 0.0018F/1.6KV J or PP CAP. 0.0018F/1.6KV J or PP CAP. 0.0018F/1.6KV J or METALLIZED FILM CAP. 0.0018F/1.6KV J P.P. CAP 0.56F/200V J or PP CAP. 0.56F/250V J or METALLIZED FILM CAP. 0.56F/200V J ELECTROLYTIC CAP. 10F/250V M ELECTROLYTIC CAP. 47F/35V M or ELECTROLYTIC CAP. 47F/35V M FILM CAP.(P) 0.01F/50V J or FILM CAP.(P) 0.01F/50V J PP CAP. 0.018F/1.6KV J or PP CAP. 0.018F/1.6KV J or PP CAP. 0.018F/1.6KV J P.P. CAP 0.033F/200V J or P.P. CAP. 0.033F/200V K or METALLIZED FILM CAP. 0.033F/200V J ELECTROLYTIC CAP. 1F/160V M or ELECTROLYTIC CAP. 1F/160V M CERAMIC CAP. B K 220pF/500V ELECTROLYTIC CAP. 10F/50V M or ELECTROLYTIC CAP. 10F/50V M METALLIZED FILM CAP. 0.1F/250V or FILM CAP.(MP) 0.1F/250V K or METALLIZED FILM CAP. 0.1F/275V K CERAMIC CAP.(AX) B K 470pF/50V CERAMIC CAP. F Z 0.01F/500V or CERAMIC CAP. 0.01F/AC250V CERAMIC CAP. F Z 0.01F/500V or CERAMIC CAP. 0.01F/AC250V CERAMIC CAP. B K 1000pF/2KV or CERAMIC CAP. B K 1000pF/2KV or CERAMIC CAP. 1000pF/2KV

C401 C402 C403

CERAMIC CAP.(AX) X K 4700pF/16V MYLAR CAP. 0.22F/50V J or FILM CAP.(P) 0.22F/50V J ELECTROLYTIC CAP. 1F/50V M or ELECTROLYTIC CAP. 1F/50V M or ELECTROLYTIC CAP. 1F/50V M

C404

ELECTROLYTIC CAP. 0.1F/50V M or ELECTROLYTIC CAP. 0.1F/50V M or ELECTROLYTIC CAP. 0.1F/50V M

C405 C408 C409

ELECTROLYTIC CAP. 47F/16V M or ELECTROLYTIC CAP. 47F/16V M CERAMIC CAP.(AX) F Z 0.1F/50V or CERAMIC CAP.(AX) F Z 0.1F/50V ELECTROLYTIC CAP. 1F/50V M or ELECTROLYTIC CAP. 1F/50V M or ELECTROLYTIC CAP. 1F/50V M

C421 C422 C423 C424 C431 C432 C433 C434 C435 C441 C442 C446

CERAMIC CAP.(AX) X K 4700pF/16V CERAMIC CAP.(AX) X K 4700pF/16V PCB JUMPER D0.6-P5.0 PCB JUMPER D0.6-P5.0 ELECTROLYTIC CAP. 2.2F/50V M or ELECTROLYTIC CAP. 2.2F/50V M ELECTROLYTIC CAP. 10F/50V M or ELECTROLYTIC CAP. 10F/50V M CERAMIC CAP.(AX) X K 2700pF/16V FILM CAP.(P) 0.1F/50V J or FILM CAP.(P) 0.1F/50V J CERAMIC CAP.(AX) F Z 0.01F/25V CERAMIC CAP.(AX) F Z 0.01F/25V ELECTROLYTIC CAP. 10F/50V M or ELECTROLYTIC CAP. 10F/50V M ELECTROLYTIC CAP. 1F/50V M or ELECTROLYTIC CAP. 1F/50V M or ELECTROLYTIC CAP. 1F/50V M

C610# # C611 C613 C614 C615 C616 C617 C618

ELECTROLYTIC CAP. 220F/200V or ELECTROLYTIC CAP. 220F/200V SL X FILM CAP.(P) 0.0056F/50V J or FILM CAP.(P) 0.0056F/50V J FILM CAP.(P) 0.056F/50V J or FILM CAP.(P) 0.056F/50V J CERAMIC CAP.(AX) X K 2700pF/16V CERAMIC CAP.(AX) B K 100pF/50V FILM CAP.(P) 0.1F/50V J or FILM CAP.(P) 0.1F/50V J CERAMIC CAP.(AX) B K 330pF/50V FILM CAP.(P) 0.1F/50V J or FILM CAP.(P) 0.1F/50V J

C527# # C531 C532 C533 C535 C539# # # C541

ELECTROLYTIC CAP. 3.3F/50V M or ELECTROLYTIC CAP. 3.3F/50V M ELECTROLYTIC CAP. 100F/10V M or ELECTROLYTIC CAP. 100F/10V M ELECTROLYTIC CAP. 47F/35V M or ELECTROLYTIC CAP. 47F/35V M FILM CAP.(P) 0.1F/50V J or FILM CAP.(P) 0.1F/50V J ELECTROLYTIC CAP. 1.5F/50V M LL ELECTROLYTIC CAP. 1000F/25V M or ELECTROLYTIC CAP. 1000F/25V M or ELECTROLYTIC CAP. 1000F/25V M ELECTROLYTIC CAP. 470F/35V M(VR) or ELECTROLYTIC CAP. 470F/35V M or ELECTROLYTIC CAP. 470F/35V M

If C642 is 0.01F, then C643 is 0.01F. C642# # # C643# # # SAFETY CAP. 10000pF/250V or SAFETY CAP. F M 0.01F/250V or CERAMIC CAP. 0.01F F CS SAFETY CAP. 10000pF/250V or SAFETY CAP. F M 0.01F/250V or CERAMIC CAP. 0.01F F CS

C551 C552# C556 C561

PCB JUMPER D0.6-P5.0 METALIZED PLYESTER CAP. 1F/100V J FILM CAP.(P) 0.1F/50V J or FILM CAP.(P) 0.1F/50V J ELECTROLYTIC CAP. 47F/35V M or

If C643 is 4700pF, then JS642 (PCB JUMPER) is used.

20030318

13-2

L6550EL

Ref. No.
C643# JS642 C654# # # C655

Description
SAFETY CAP. 4700pF/250V KX PCB JUMPER D0.6-P10.0 ELECTROLYTIC CAP. 1F/50V M or ELECTROLYTIC CAP. 1F/50V M or ELECTROLYTIC CAP. 1F/50V M ELECTROLYTIC CAP. 1000F/16V M(VR/HC) or ELECTROLYTIC CAP. 1000F/16V M or ELECTROLYTIC CAP. 1000F/16V M

Part No.
CA2E472MR050 JW10.0T CE1JMASTL1R0 CE1JMASDL1R0 CE1JMASDL010 CE1CMZNTL102 CE1CMZPDL102 CE1CMZADL102 CE2CMZPTL101 CE2CMZNDL101 CE1GMZNTL471 CE1GMZADL471 CE1GMZNDL471 CE1CMZNTL102 CE1CMZPDL102 CE1CMZADL102 CE1JMASTL1R0 CE1JMASDL1R0 CE1JMASDL010 CE1AMASTL101 CE1AMASDL101 CE1AMASTL101 CE1AMASDL101 CE1AMASTL101 CE1AMASDL101 CE1CMASTL330 CE1CMASDL330 CE1AMASTL101 CE1AMASDL101 CE2CMZPTL101 CE2CMZNDL101 CCA1JKT0B101 CDA1CKT0X472 CE1JMASTLR47 CE1JMASDLR47 CDA1CKT0X472 CE1JMASTLR47 CE1JMASDLR47 CE1CMASTL471 CE1CMASDL471 CE1CMASTL471 CE1CMASDL471 CMA1JJS00104 CA1J104MS029 CMA1JJS00104 CA1J104MS029 CE1JMASTL1R0 CE1JMASDL1R0 CE1JMASDL010 CE1JMASTL1R0 CE1JMASDL1R0 CE1JMASDL010 CE1CMASTL220 CE1CMASDL220 CE1CMASTL101 CE1CMASDL101 CE1CMASTL471 CE1CMASDL471 CE1CMASTL471 CE1CMASDL471 CE1CMASTL101

Ref. No.
# C831 C833 CN571# # # CN691# # CN801

Description
ELECTROLYTIC CAP. 100F/16V M ELECTROLYTIC CAP. 100F/16V M or ELECTROLYTIC CAP. 100F/16V M CERAMIC CAP.(AX) F Z 0.01F/25V

Part No.
CE1CMASDL101 CE1CMASTL101 CE1CMASDL101 CDA1EZT0F103 J3TVC05TG002 J3RTC05JG001 1730812 J3TVC02TG002 J3RTC02JG001

CONNECTORS
CONNECTOR BASE, 5P TV-50P-05-V3 or CONNECTOR BASE, 5P RTB-1.5-5P or CONNECTOR BASE, 5P W-P3005-02 CONNECTOR BASE, 2P TV-50P-02-V3 or CONNECTOR BASE, 2P RTB-1.5-2P

C656 C657

ELECTROLYTIC CAP. 100F/160V M or ELECTROLYTIC CAP. 100F/160V M ELECTROLYTIC CAP. 470F/35V M(VR) or ELECTROLYTIC CAP. 470F/35V M or ELECTROLYTIC CAP. 470F/35V M

STRAIGHT CONNECTOR BASE 00 8283 0212 00 J383C02UG002 000 or STRAIGHT PIN HEADER, 2P 173981-2 1770258 STRAIGHT CONNECTOR BASE 00 8283 0212 00 J383C02UG002 000 or STRAIGHT PIN HEADER, 2P 173981-2 1770258 QDTZ001SS133 NDTZ001N4148 QDTZ001SS133 NDTZ001N4148 QDTB0MTZJ5R6 NDTB0DZ5R6BS QDTB0MTZJ5R1 NDTB0DZ5R1BS QDTB0MTZJ5R6 NDTB0DZ5R6BS QDTZ001SS133 NDTZ001N4148 QDTZ001SS133 NDTZ001N4148 QDTB0MTZJ9R1 NDTB0DZ9R1BS QDTZ001SS133 NDTZ001N4148 QDTB0MTZJ8R2 NDTB0DZ8R2BS QDTZ001SS133 NDTZ001N4148 QDTZ001SS133 NDTZ001N4148 QDTZ001SS133 NDTZ001N4148 QDTB00MTZJ20 NDTB00DZ20BS QDTZ001SS133 NDTZ001N4148 NDLZ001N5397 AERA1502**** QDTB00MTZJ15 NDTB00DZ15BS QDTZ001SS133 NDTZ001N4148 NDLZ000FR104 QDPZ0ERA2202 QDQZ0010ELS2 QDPZ0ERA2202 QDQZ0010ELS2 QDPZ0ERA2202 QDQZ0010ELS2 QDLZ0ERD0715

C658# # # C667

ELECTROLYTIC CAP. 1000F/16V M(VR/HC) or ELECTROLYTIC CAP. 1000F/16V M or ELECTROLYTIC CAP. 1000F/16V M ELECTROLYTIC CAP. 1F/50V M or ELECTROLYTIC CAP. 1F/50V M or ELECTROLYTIC CAP. 1F/50V M

CN802

DIODES
D101 D102 D112 D131 D151 D181 D322 D323 D326 D327 D351 D352 D353 D525# # D526# # D532 D552# # D558 D571# # # D572# # D573# # D580 SWITCHING DIODE 1SS133(T-77) or SWITCHING DIODE 1N4148 SWITCHING DIODE 1SS133(T-77) or SWITCHING DIODE 1N4148 ZENER DIODE MTZJT-775.6B or ZENER DIODE DZ-5.6BSBT265 ZENER DIODE MTZJT-775.1B or ZENER DIODE DZ-5.1BSBT265 ZENER DIODE MTZJT-775.6B or ZENER DIODE DZ-5.6BSBT265 SWITCHING DIODE 1SS133(T-77) or SWITCHING DIODE 1N4148 SWITCHING DIODE 1SS133(T-77) or SWITCHING DIODE 1N4148 ZENER DIODE MTZJT-779.1B or ZENER DIODE DZ-9.1BSBT265 SWITCHING DIODE 1SS133(T-77) or SWITCHING DIODE 1N4148 ZENER DIODE MTZJT-778.2B or ZENER DIODE DZ-8.2BSBT265 SWITCHING DIODE 1SS133(T-77) or SWITCHING DIODE 1N4148 SWITCHING DIODE 1SS133(T-77) or SWITCHING DIODE 1N4148 SWITCHING DIODE 1SS133(T-77) or SWITCHING DIODE 1N4148 ZENER DIODE MTZJT-7720B or ZENER DIODE DZ-20BSBT265 SWITCHING DIODE 1SS133(T-77) or SWITCHING DIODE 1N4148 DIODE 1N5397-B or RECTIFIER DIODE ERA15-02 ZENER DIODE MTZJT-7715B or ZENER DIODE DZ-15BSBT265 SWITCHING DIODE 1SS133(T-77) or SWITCHING DIODE 1N4148 DIODE FR104-B or RECTIFIER DIODE ERA22-02 or RECTIFIER DIODE 10ELS2 RECTIFIER DIODE ERA22-02 or RECTIFIER DIODE 10ELS2 RECTIFIER DIODE ERA22-02 or RECTIFIER DIODE 10ELS2 DIODE ERD07-15

C681 C682 C683 C686 C687 C692 C701 C711 C712 C721 C722 C801 C802 C803 C804 C808

ELECTROLYTIC CAP. 100F/10V M or ELECTROLYTIC CAP. 100F/10V M ELECTROLYTIC CAP. 100F/10V M or ELECTROLYTIC CAP. 100F/10V M ELECTROLYTIC CAP. 100F/10V M or ELECTROLYTIC CAP. 100F/10V M ELECTROLYTIC CAP. 33F/16V M or ELECTROLYTIC CAP. 33F/16V M ELECTROLYTIC CAP. 100F/10V M or ELECTROLYTIC CAP. 100F/10V M ELECTROLYTIC CAP. 100F/160V M or ELECTROLYTIC CAP. 100F/160V M CERAMIC CAP.(AX) B K 100pF/50V CERAMIC CAP.(AX) X K 4700pF/16V ELECTROLYTIC CAP. 0.47F/50V M or ELECTROLYTIC CAP. 0.47F/50V M CERAMIC CAP.(AX) X K 4700pF/16V ELECTROLYTIC CAP. 0.47F/50V M or ELECTROLYTIC CAP. 0.47F/50V M ELECTROLYTIC CAP. 470F/16V M or ELECTROLYTIC CAP. 470F/16V M ELECTROLYTIC CAP. 470F/16V M or ELECTROLYTIC CAP. 470F/16V M FILM CAP.(P) 0.1F/50V J or FILM CAP.(P) 0.1F/50V J FILM CAP.(P) 0.1F/50V J or FILM CAP.(P) 0.1F/50V J ELECTROLYTIC CAP. 1F/50V M or ELECTROLYTIC CAP. 1F/50V M or ELECTROLYTIC CAP. 1F/50V M

C809

ELECTROLYTIC CAP. 1F/50V M or ELECTROLYTIC CAP. 1F/50V M or ELECTROLYTIC CAP. 1F/50V M

C812 C814 C821 C822 C827#

ELECTROLYTIC CAP. 22F/16V M or ELECTROLYTIC CAP. 22F/16V M ELECTROLYTIC CAP. 100F/16V M or ELECTROLYTIC CAP. 100F/16V M ELECTROLYTIC CAP. 470F/16V M or ELECTROLYTIC CAP. 470F/16V M ELECTROLYTIC CAP. 470F/16V M or ELECTROLYTIC CAP. 470F/16V M ELECTROLYTIC CAP. 100F/16V M or

20030318

13-3

L6550EL

Ref. No.
D582 D583 D584# # D585 D586 D587 D588 D591# # D595# # D597 D605# # D606# # D607# # D608# # D609 D611# # D615# D621 D622 D641 D642# # D643 D651# # D652# # D653 D654# # D655# # D657# D660 D661# # D662# # D666

Description
FAST RECOVERY DIODE ERD38-06 SWITCHING DIODE 1SS133(T-77) or SWITCHING DIODE 1N4148 SWITCHING DIODE 1SS133(T-77) or SWITCHING DIODE 1N4148 SWITCHING DIODE 1SS133(T-77) or SWITCHING DIODE 1N4148 SWITCHING DIODE 1SS133(T-77) or SWITCHING DIODE 1N4148 ZENER DIODE MTZJT-775.6B or ZENER DIODE DZ-5.6BSBT265 SWITCHING DIODE 1SS133(T-77) or SWITCHING DIODE 1N4148 ZENER DIODE MTZJT-7736B or ZENER DIODE DZ-36BSBT265 SWITCHING DIODE 1SS133(T-77) or SWITCHING DIODE 1N4148 ZENER DIODE MTZJT-776.8B or ZENER DIODE DZ-6.8BSBT265 DIODE 1N5406 or DIODE ERC04-06L3 DIODE 1N5406 or DIODE ERC04-06L3 DIODE 1N5406 or DIODE ERC04-06L3 DIODE 1N5406 or DIODE ERC04-06L3 SWITCHING DIODE 1SS133(T-77) or SWITCHING DIODE 1N4148 ZENER DIODE MTZJT-7715B or ZENER DIODE DZ-15BSBT265 SWITCHING DIODE 1N4148 T-77 ZENER DIODE MTZJT-777.5B or ZENER DIODE DZ-7.5BSBT265 SWITCHING DIODE 1SS133(T-77) or SWITCHING DIODE 1N4148 SWITCHING DIODE 1SS133(T-77) or SWITCHING DIODE 1N4148 SWITCHING DIODE 1SS133(T-77) or SWITCHING DIODE 1N4148 SWITCHING DIODE 1SS133(T-77) or SWITCHING DIODE 1N4148 FAST RECOVERY DIODE 30DF6 or DIODE ERD29-06J DIODE FR154 or FAST RECOVERY DIODE ERB44-02 DIODE FR154 or FAST RECOVERY DIODE ERB44-02 SWITCHING DIODE 1SS133(T-77) or SWITCHING DIODE 1N4148 DIODE FR154 or FAST RECOVERY DIODE ERB44-02 DIODE 1ZC36 SWITCHING DIODE 1SS133(T-77) or SWITCHING DIODE 1N4148 SWITCHING DIODE 1SS133(T-77) or SWITCHING DIODE 1N4148 ZENER DIODE MTZJT-776.8B or ZENER DIODE DZ-6.8BSBT265 ZENER DIODE MTZJT-7736B or ZENER DIODE DZ-36BSBT265

Part No.
QDQZ0ERD3806 QDTZ001SS133 NDTZ001N4148 QDTZ001SS133 NDTZ001N4148 QDTZ001SS133 NDTZ001N4148 QDTZ001SS133 NDTZ001N4148 QDTB0MTZJ5R6 NDTB0DZ5R6BS QDTZ001SS133 NDTZ001N4148 QDTB00MTZJ36 NDTB00DZ36BS QDTZ001SS133 NDTZ001N4148 QDTB0MTZJ6R8 NDTB0DZ6R8BS NDLZ001N5406 QD4Z0ERC0406 NDLZ001N5406 QD4Z0ERC0406 NDLZ001N5406 QD4Z0ERC0406 NDLZ001N5406 QD4Z0ERC0406 QDTZ001SS133 NDTZ001N4148 QDTB00MTZJ15 NDTB00DZ15BS QDTZ001N4148 QDTB0MTZJ7R5 NDTB0DZ7R5BS QDTZ001SS133 NDTZ001N4148 QDTZ001SS133 NDTZ001N4148 QDTZ001SS133 NDTZ001N4148 QDTZ001SS133 NDTZ001N4148 QDWZ00030DF6 QD4Z0ERD2906 NDLZ000FR154 QDPZ0ERB4402 NDLZ000FR154 QDPZ0ERB4402 QDTZ001SS133 NDTZ001N4148 NDLZ000FR154 QDPZ0ERB4402 QDQZ0001ZC36 QDTZ001SS133 NDTZ001N4148 QDTZ001SS133 NDTZ001N4148 QDTB0MTZJ6R8 NDTB0DZ6R8BS QDTB00MTZJ36 NDTB00DZ36BS

Ref. No.
D671# # D672 D673 D681 D683 D691# # D695 D696 D826 D838 D841# # D842# # D845# #

Description
SWITCHING DIODE 1SS133(T-77) or SWITCHING DIODE 1N4148 PCB JUMPER D0.6-P5.0 SWITCHING DIODE 1SS133(T-77) or SWITCHING DIODE 1N4148 ZENER DIODE MTZJT-779.1B or ZENER DIODE DZ-9.1BSBT265 PCB JUMPER D0.6-P10.0 SWITCHING DIODE 1SS133(T-77) or SWITCHING DIODE 1N4148 ZENER DIODE MTZJT-778.2B or ZENER DIODE DZ-8.2BSBT265 SWITCHING DIODE 1SS133(T-77) or SWITCHING DIODE 1N4148 SWITCHING DIODE 1SS133(T-77) or SWITCHING DIODE 1N4148 ZENER DIODE MTZJT-7710B or ZENER DIODE DZ-10BSBT265 SWITCHING DIODE 1SS133(T-77) or SWITCHING DIODE 1N4148 ZENER DIODE MTZJT-775.1B or ZENER DIODE DZ-5.1BSBT265 SWITCHING DIODE 1SS133(T-77) or SWITCHING DIODE 1N4148

Part No.
QDTZ001SS133 NDTZ001N4148 JW5.0T QDTZ001SS133 NDTZ001N4148 QDTB0MTZJ9R1 NDTB0DZ9R1BS JW10.0T QDTZ001SS133 NDTZ001N4148 QDTB0MTZJ8R2 NDTB0DZ8R2BS QDTZ001SS133 NDTZ001N4148 QDTZ001SS133 NDTZ001N4148 QDTB00MTZJ10 NDTB00DZ10BS QDTZ001SS133 NDTZ001N4148 QDTB0MTZJ5R1 NDTB0DZ5R1BS QDTZ001SS133 NDTZ001N4148 QSZBA0SMB010 QSZAB0RMB127 NSZBA0SSM028 NSMMA0SAZ012 NSMMA0SSS028 QSMBA0SRM003 QSMMA0SRM003 NSZBA0SBG001 NSZAA0SSS004 QSZBA0SSY003 QSZBA0TTS096 NSZBA0TF3079 QSZBA0SSY006 QSZBA0SSY004 QPEW0PS25011 QPEL0PS25011 NPEB0LTV817F NPEC0LTV817F QSZBA0SMS007 LLARKBSTU220 LLARKDQKA220 LLAXJATTU150 LLAXKDTKA150 LLAXJATTU220 LLAXKDTKA220 LLARKBSTU101 LLARKDQKA101 LLARKBSTU220 LLARKDQKA220 LLARKBSTU101 LLARKDQKA101 JW5.0T JW5.0T LLBD00PMS008

ICS
IC31 IC111# IC151 IC:VIF/SIF DETECTOR M61111FP IC M61271M8-050FP-61 IC:MEMORY S524C20D21 or IC:MEMORY AT24C02N-10SC or IC(EEPROM) M24C02-MN6 or IC:MEMORY BR24C02F-W or IC:MEMORY BR24C02F or IC:EEPROM CAT24WC02JI or IC(EEP-ROM) M24C02-WMN6 IC401 IC481 IC551# # IC601# # # # IC802 L3 L32 L33 L51 L111 L301 L341 L342 L561 IC:USA STEREO DECODER LA7765 IC:SWITCHING TC4052BF(EL) or IC:SWITCHING CD4052BCSJX IC:VERTICAL OUTPUT LA78041 or IC:VERTICAL OUTPUT LA78045 PHOTOCOUPLER PS2501-1W or PHOTO COUPLER PS2501-1L or PHOTOCOUPLER LTV-817B-F or PHOTOCOUPLER LTV-817C-F AUDIO POWER IC AN17805A

COILS
INDUCTOR 22H-K-5FT or INDUCTOR 22H-K INDUCTOR 15H-J-26T or INDUCTOR 15H-K-26T INDUCTOR 22H-J-26T or INDUCTOR 22H-K-26T INDUCTOR 100H-K-5FT or INDUCTOR 100H-K INDUCTOR 22H-K-5FT or INDUCTOR 22H-K INDUCTOR 100H-K-5FT or INDUCTOR 100H-K PCB JUMPER D0.6-P5.0 PCB JUMPER D0.6-P5.0 LINEARITY COIL ELH5L6136N

20030318

13-4

L6550EL

Ref. No.
L562 L601# # # L692

Description
CHOKE COIL ELC18B471LM LINE FILTER JLB2808 or LINE FILTER MS036 or LINE FILTER CSA-LF032 CHOKE COIL 47H-K or POT COIL 47H K or POT COIL 47H K

Part No.
LLC471KMS001 LLBG00ZXB004 LLBG00ZY2009 LLBG00ZSA007 LLBD00PKV007 LLBD**DMM001 LLBD00DQE001

Ref. No.
Q531

Description
TRANSISTOR 2SC2785(F) or TRANSISTOR 2SC2785(H) or TRANSISTOR 2SC2785(J) or TRANSISTOR KTC3199(GR) or TRANSISTOR KTC3198(GR) or TRANSISTOR 2SC3331(T)-AANP or TRANSISTOR 2SC3331(U)-AANP or TRANSISTOR 2SC1815-GR(TPE2)

Part No.
QQSF02SC2785 QQSH02SC2785 QQSJ02SC2785 NQS10KTC3199 NQS40KTC3198 2SC3331TZ 2SC3331UZ QQS102SC1815 QQSF02SC2785 QQSH02SC2785 QQSJ02SC2785 NQS10KTC3199 NQS40KTC3198 2SC3331TZ 2SC3331UZ QQS102SC1815 QQSF02SA1175 NQS10KTA1267 NQS40KTA1266 2SA1318TZ 2SA1318UZ QQS102SA1015 QQER02SD1666 QQES02SD1666 NQ400KTD2059 NQ4Y0KTD2059 Q2SD1825**** QQSF02SC2785 QQSH02SC2785 QQSJ02SC2785 NQS10KTC3199 NQS40KTC3198 2SC3331TZ 2SC3331UZ QQS102SC1815 QQSF02SC2785 QQSH02SC2785 QQSJ02SC2785 NQS10KTC3199 NQS40KTC3198 2SC3331TZ 2SC3331UZ QQS102SC1815 QQZZ02SD2634 QQSY02SC1627 QFFZ02SK3407 QQS002SC2120 QQSY02SC2120 QQSF02SA1175 NQS10KTA1267 NQS40KTA1266 2SA1318TZ 2SA1318UZ QQS102SA1015 QQSF02SC2785 QQSH02SC2785 QQSJ02SC2785 NQS10KTC3199 NQS40KTC3198 2SC3331TZ 2SC3331UZ

TRANSISTORS
Q31 TRANSISTOR 2SC2785(F) or TRANSISTOR 2SC2785(H) or TRANSISTOR 2SC2785(J) or TRANSISTOR KTC3199(GR) or TRANSISTOR KTC3198(GR) or TRANSISTOR 2SC3331(T)-AANP or TRANSISTOR 2SC3331(U)-AANP or TRANSISTOR 2SC1815-GR(TPE2) Q111 TRANSISTOR 2SC2785(F) or TRANSISTOR 2SC2785(H) or TRANSISTOR 2SC2785(J) or TRANSISTOR KTC3199(GR) or TRANSISTOR KTC3198(GR) or TRANSISTOR 2SC3331(T)-AANP or TRANSISTOR 2SC3331(U)-AANP or TRANSISTOR 2SC1815-GR(TPE2) Q321# # # # # # # # Q361 TRANSISTOR 2SC2785(F) or TRANSISTOR 2SC2785(H) or TRANSISTOR 2SC2785(J) or TRANSISTOR KTC3199(GR) or TRANSISTOR KTC3198(GR) or TRANSISTOR 2SC3331(T)-AANP or TRANSISTOR 2SC3331(U)-AANP or TRANSISTOR 2SC1815-GR(TPE2) TRANSISTOR 2SC2785(F) or TRANSISTOR 2SC2785(H) or TRANSISTOR 2SC2785(J) or TRANSISTOR KTC3199(GR) or TRANSISTOR KTC3198(GR) or TRANSISTOR 2SC3331(T)-AANP or TRANSISTOR 2SC3331(U)-AANP or TRANSISTOR 2SC1815-GR(TPE2) Q411 TRANSISTOR 2SA1175(F) or TRANSISTOR KTA1267(GR) or TRANSISTOR KTA1266(GR) or TRANSISTOR 2SA1318(T)-AANP or TRANSISTOR 2SA1318(U)-AANP or TRANSISTOR 2SA1015-GR(TPE2) Q441 TRANSISTOR 2SA1175(F) or TRANSISTOR KTA1267(GR) or TRANSISTOR KTA1266(GR) or TRANSISTOR 2SA1318(T)-AANP or TRANSISTOR 2SA1318(U)-AANP or TRANSISTOR 2SA1015-GR(TPE2) Q481 TRANSISTOR 2SC2785(F) or TRANSISTOR 2SC2785(H) or TRANSISTOR 2SC2785(J) or TRANSISTOR KTC3199(GR) or TRANSISTOR KTC3198(GR) or TRANSISTOR 2SC3331(T)-AANP or TRANSISTOR 2SC3331(U)-AANP or TRANSISTOR 2SC1815-GR(TPE2) QQSF02SC2785 QQSH02SC2785 QQSJ02SC2785 NQS10KTC3199 NQS40KTC3198 2SC3331TZ 2SC3331UZ QQS102SC1815 QQSF02SC2785 QQSH02SC2785 QQSJ02SC2785 NQS10KTC3199 NQS40KTC3198 2SC3331TZ 2SC3331UZ QQS102SC1815 QQSF02SC2785 QQSH02SC2785 QQSJ02SC2785 NQS10KTC3199 NQS40KTC3198 2SC3331TZ 2SC3331UZ QQS102SC1815 QQSF02SC2785 QQSH02SC2785 QQSJ02SC2785 NQS10KTC3199 NQS40KTC3198 2SC3331TZ 2SC3331UZ QQS102SC1815 QQSF02SA1175 NQS10KTA1267 NQS40KTA1266 2SA1318TZ 2SA1318UZ QQS102SA1015 QQSF02SA1175 NQS10KTA1267 NQS40KTA1266 2SA1318TZ 2SA1318UZ QQS102SA1015 QQSF02SC2785 QQSH02SC2785 QQSJ02SC2785 NQS10KTC3199 NQS40KTC3198 2SC3331TZ 2SC3331UZ QQS102SC1815 Q662# # # # # # # Q571# Q572 Q601# Q602# # Q641 Q561 Q551# # # # # # Q552# # # # # Q553 Q532

TRANSISTOR 2SC2785(F) or TRANSISTOR 2SC2785(H) or TRANSISTOR 2SC2785(J) or TRANSISTOR KTC3199(GR) or TRANSISTOR KTC3198(GR) or TRANSISTOR 2SC3331(T)-AANP or TRANSISTOR 2SC3331(U)-AANP or TRANSISTOR 2SC1815-GR(TPE2) TRANSISTOR 2SA1175(F) or TRANSISTOR KTA1267(GR) or TRANSISTOR KTA1266(GR) or TRANSISTOR 2SA1318(T)-AANP or TRANSISTOR 2SA1318(U)-AANP or TRANSISTOR 2SA1015-GR(TPE2) TRANSISTOR 2SD1666R or TRANSISTOR 2SD1666S or TRANSISTOR KTD2059(O) or TRANSISTOR KTD2059(Y) or TRANSISTOR 2SD1825 TRANSISTOR 2SC2785(F) or TRANSISTOR 2SC2785(H) or TRANSISTOR 2SC2785(J) or TRANSISTOR KTC3199(GR) or TRANSISTOR KTC3198(GR) or TRANSISTOR 2SC3331(T)-AANP or TRANSISTOR 2SC3331(U)-AANP or TRANSISTOR 2SC1815-GR(TPE2) TRANSISTOR 2SC2785(F) or TRANSISTOR 2SC2785(H) or TRANSISTOR 2SC2785(J) or TRANSISTOR KTC3199(GR) or TRANSISTOR KTC3198(GR) or TRANSISTOR 2SC3331(T)-AANP or TRANSISTOR 2SC3331(U)-AANP or TRANSISTOR 2SC1815-GR(TPE2) TRANSISTOR 2SD2634 TRANSISTOR 2SC1627Y-TPE2 FET 2SK3407 TRANSISTOR 2SC2120-O-TPE2 or TRANSISTOR 2SC2120-Y(TPE2) TRANSISTOR 2SA1175(F) or TRANSISTOR KTA1267(GR) or TRANSISTOR KTA1266(GR) or TRANSISTOR 2SA1318(T)-AANP or TRANSISTOR 2SA1318(U)-AANP or TRANSISTOR 2SA1015-GR(TPE2) TRANSISTOR 2SC2785(F) or TRANSISTOR 2SC2785(H) or TRANSISTOR 2SC2785(J) or TRANSISTOR KTC3199(GR) or TRANSISTOR KTC3198(GR) or TRANSISTOR 2SC3331(T)-AANP or TRANSISTOR 2SC3331(U)-AANP or

20030318

13-5

L6550EL

Ref. No.
# Q671# # # # # # Q675

Description
TRANSISTOR 2SC1815-GR(TPE2) TRANSISTOR 2SA1175(F) or TRANSISTOR KTA1267(GR) or TRANSISTOR KTA1266(GR) or TRANSISTOR 2SA1318(T)-AANP or TRANSISTOR 2SA1318(U)-AANP or TRANSISTOR 2SA1015-GR(TPE2) TRANSISTOR 2SC2785(F) or TRANSISTOR 2SC2785(H) or TRANSISTOR 2SC2785(J) or TRANSISTOR KTC3199(GR) or TRANSISTOR KTC3198(GR) or TRANSISTOR 2SC3331(T)-AANP or TRANSISTOR 2SC3331(U)-AANP or TRANSISTOR 2SC1815-GR(TPE2)

Part No.
QQS102SC1815 QQSF02SA1175 NQS10KTA1267 NQS40KTA1266 2SA1318TZ 2SA1318UZ QQS102SA1015 QQSF02SC2785 QQSH02SC2785 QQSJ02SC2785 NQS10KTC3199 NQS40KTC3198 2SC3331TZ 2SC3331UZ QQS102SC1815 QQSF02SC2785 QQSH02SC2785 QQSJ02SC2785 NQS10KTC3199 NQS40KTC3198 2SC3331TZ 2SC3331UZ QQS102SC1815 QQS002SC2120 QQSY02SC2120 NQSY0KTC3203 QQS002SC2120 QQSY02SC2120 NQSY0KTC3203 QQS002SC2120 QQSY02SC2120 NQSY0KTC3203 QQSZ00BA1F4M NQSZ0KRC103M QQSF02SC2785 QQSH02SC2785 QQSJ02SC2785 NQS10KTC3199 NQS40KTC3198 2SC3331TZ 2SC3331UZ QQS102SC1815 QQSS002SB892 QQST002SB892 QQSF02SC2785 QQSH02SC2785 QQSJ02SC2785 NQS10KTC3199 NQS40KTC3198 2SC3331TZ 2SC3331UZ QQS102SC1815 QQSF02SC2785 QQSH02SC2785 QQSJ02SC2785 NQS10KTC3199 NQS40KTC3198 2SC3331TZ 2SC3331UZ QQS102SC1815

Ref. No.
R3 R4 R5 R21 R31 R32 R33 R34 R36 R37 R41 R42 R43 R51 R52 R54 R102 R103 R104 R105 R106 R111# # R112 R113 R114 R116 R117 R132 R133 R135 R136 R137 R138 R139 R140 R141 R151 R155 R156 R161 R162 R163 R164 R166 R168

Description RESISTORS
PCB JUMPER D0.6-P5.0 CARBON RES. 1/4W J 100 or CARBON RES. 1/6W J 100 CARBON RES. 1/4W J 100 or CARBON RES. 1/6W J 100 CARBON RES. 1/4W J 6.8k CARBON RES. 1/4W J 2.2k CARBON RES. 1/4W J 390 or CARBON RES. 1/6W J 390 CARBON RES. 1/4W J 270 or CARBON RES. 1/6W J 270 CARBON RES. 1/4W J 180 or CARBON RES. 1/6W J 180 CARBON RES. 1/4W J 10k CARBON RES. 1/4W J 470 or CARBON RES. 1/6W J 470 CARBON RES. 1/4W J 2.2k CARBON RES. 1/4W J 56k CARBON RES. 1/4W J 12k CARBON RES. 1/4W J 220k CARBON RES. 1/4W J 220k CARBON RES. 1/4W J 22k CARBON RES. 1/4W J 2.2k CARBON RES. 1/4W J 1.8k CARBON RES. 1/4W J 3.3k CARBON RES. 1/4W J 4.7k CARBON RES. 1/4W J 8.2k CARBON RES. 1/4W J 100 or CARBON RES. 1/6W J 100 CARBON RES. 1/4W J 10k CARBON RES. 1/4W J 470k CARBON RES. 1/4W J 1k or CARBON RES. 1/6W J 1k CARBON RES. 1/4W J 220 or CARBON RES. 1/6W J 220 CARBON RES. 1/4W J 470 or CARBON RES. 1/6W J 470 PCB JUMPER D0.6-P5.0 PCB JUMPER D0.6-P5.0 CARBON RES. 1/4W J 2.2k CARBON RES. 1/4W J 100k CARBON RES. 1/4W J 100 or CARBON RES. 1/6W J 100 CARBON RES. 1/4W J 220k CARBON RES. 1/4W J 22k CARBON RES. 1/4W J 1k or CARBON RES. 1/6W J 1k PCB JUMPER D0.6-P5.0 CARBON RES. 1/4W J 4.7k CARBON RES. 1/4W J 100 or CARBON RES. 1/6W J 100 CARBON RES. 1/4W J 1k or CARBON RES. 1/6W J 1k CARBON RES. 1/4W J 10k CARBON RES. 1/4W J 10k CARBON RES. 1/4W J 6.8k CARBON RES. 1/4W J 10k CARBON RES. 1/4W J 4.7k CARBON RES. 1/4W J 4.7k

Part No.
JW5.0T RCX4JATZ0101 RCX6JATZ0101 RCX4JATZ0101 RCX6JATZ0101 RCX4JATZ0682 RCX4JATZ0222 RCX4JATZ0391 RCX6JATZ0391 RCX4JATZ0271 RCX6JATZ0271 RCX4JATZ0181 RCX6JATZ0181 RCX4JATZ0103 RCX4JATZ0471 RCX6JATZ0471 RCX4JATZ0222 RCX4JATZ0563 RCX4JATZ0123 RCX4JATZ0224 RCX4JATZ0224 RCX4JATZ0223 RCX4JATZ0222 RCX4JATZ0182 RCX4JATZ0332 RCX4JATZ0472 RCX4JATZ0822 RCX4JATZ0101 RCX6JATZ0101 RCX4JATZ0103 RCX4JATZ0474 RCX4JATZ0102 RCX6JATZ0102 RCX4JATZ0221 RCX6JATZ0221 RCX4JATZ0471 RCX6JATZ0471 JW5.0T JW5.0T RCX4JATZ0222 RCX4JATZ0104 RCX4JATZ0101 RCX6JATZ0101 RCX4JATZ0224 RCX4JATZ0223 RCX4JATZ0102 RCX6JATZ0102 JW5.0T RCX4JATZ0472 RCX4JATZ0101 RCX6JATZ0101 RCX4JATZ0102 RCX6JATZ0102 RCX4JATZ0103 RCX4JATZ0103 RCX4JATZ0682 RCX4JATZ0103 RCX4JATZ0472 RCX4JATZ0472

Q676

TRANSISTOR 2SC2785(F) or TRANSISTOR 2SC2785(H) or TRANSISTOR 2SC2785(J) or TRANSISTOR KTC3199(GR) or TRANSISTOR KTC3198(GR) or TRANSISTOR 2SC3331(T)-AANP or TRANSISTOR 2SC3331(U)-AANP or TRANSISTOR 2SC1815-GR(TPE2)

Q681

TRANSISTOR 2SC2120-O-TPE2 or TRANSISTOR 2SC2120-Y(TPE2) or TRANSISTOR KTC3203(Y)

Q682

TRANSISTOR 2SC2120-O-TPE2 or TRANSISTOR 2SC2120-Y(TPE2) or TRANSISTOR KTC3203(Y)

Q683

TRANSISTOR 2SC2120-O-TPE2 or TRANSISTOR 2SC2120-Y(TPE2) or TRANSISTOR KTC3203(Y)

Q696 Q825

RES. BUILT-IN TRANSISTOR BA1F4M-T or RES. BUILT-IN TRANSISTOR KRC103M TRANSISTOR 2SC2785(F) or TRANSISTOR 2SC2785(H) or TRANSISTOR 2SC2785(J) or TRANSISTOR KTC3199(GR) or TRANSISTOR KTC3198(GR) or TRANSISTOR 2SC3331(T)-AANP or TRANSISTOR 2SC3331(U)-AANP or TRANSISTOR 2SC1815-GR(TPE2)

Q831# # Q832

TRANSISTOR 2SB892(S) or TRANSISTOR 2SB892(T) TRANSISTOR 2SC2785(F) or TRANSISTOR 2SC2785(H) or TRANSISTOR 2SC2785(J) or TRANSISTOR KTC3199(GR) or TRANSISTOR KTC3198(GR) or TRANSISTOR 2SC3331(T)-AANP or TRANSISTOR 2SC3331(U)-AANP or TRANSISTOR 2SC1815-GR(TPE2)

Q833# # # # # # # #

TRANSISTOR 2SC2785(F) or TRANSISTOR 2SC2785(H) or TRANSISTOR 2SC2785(J) or TRANSISTOR KTC3199(GR) or TRANSISTOR KTC3198(GR) or TRANSISTOR 2SC3331(T)-AANP or TRANSISTOR 2SC3331(U)-AANP or TRANSISTOR 2SC1815-GR(TPE2)

20030318

13-6

L6550EL

Ref. No.
R170 R171 R172 R173 R301 R303 R322 R323 R326 R327 R328 R329 R330 R331 R342 R344 R345 R346 R347# R348 R355 R356 R357 R358 R361 R362 R402 R403 R405 R406 R407 R408 R409 R412 R421 R422 R432 R435 R436 R441 R442 R443 R445 R481 R482 R521 R522 R523

Description
CARBON RES. 1/4W J 6.8k CARBON RES. 1/4W J 3.3k PCB JUMPER D0.6-P5.0 PCB JUMPER D0.6-P5.0 CARBON RES. 1/4W J 6.8k CARBON RES. 1/4W J 100 or CARBON RES. 1/6W J 100 PCB JUMPER D0.6-P5.0 CARBON RES. 1/4W J 2.2k CARBON RES. 1/4W J 100 or CARBON RES. 1/6W J 100 PCB JUMPER D0.6-P5.0 CARBON RES. 1/4W J 3.3k CARBON RES. 1/4W J 56k CARBON RES. 1/4W J 1k or CARBON RES. 1/6W J 1k PCB JUMPER D0.6-P5.0 PCB JUMPER D0.6-P5.0 CARBON RES. 1/4W J 6.8k CARBON RES. 1/4W J 10k CARBON RES. 1/4W J 470 or CARBON RES. 1/6W J 470 PCB JUMPER D0.6-P5.0 CARBON RES. 1/4W J 27k CARBON RES. 1/4W J 33k CARBON RES. 1/4W J 220 or CARBON RES. 1/6W J 220 CARBON RES. 1/4W J 220 or CARBON RES. 1/6W J 220 CARBON RES. 1/4W J 220 or CARBON RES. 1/6W J 220 CARBON RES. 1/4W J 4.7k CARBON RES. 1/4W J 100 or CARBON RES. 1/6W J 100 CARBON RES. 1/4W J 5.6k PCB JUMPER D0.6-P5.0 CARBON RES. 1/4W J 3.3k CARBON RES. 1/4W J 15k CARBON RES. 1/4W J 6.8k CARBON RES. 1/4W J 10k CARBON RES. 1/4W J 10k CARBON RES. 1/4W J 10k CARBON RES. 1/4W J 4.7k CARBON RES. 1/4W J 4.7k CARBON RES. 1/4W J 220 or CARBON RES. 1/6W J 220 CARBON RES. 1/4W J 470 or CARBON RES. 1/6W J 470 CARBON RES. 1/4W J 10k CARBON RES. 1/4W J 10k CARBON RES. 1/4W J 10k CARBON RES. 1/4W J 10k CARBON RES. 1/4W J 10k CARBON RES. 1/4W J 10k CARBON RES. 1/4W J 22k CARBON RES. 1/4W J 680 or CARBON RES. 1/6W J 680 CARBON RES. 1/4W J 680 or CARBON RES. 1/6W J 680 CARBON RES. 1/4W J 680 or CARBON RES. 1/6W J 680

Part No.
RCX4JATZ0682 RCX4JATZ0332 JW5.0T JW5.0T RCX4JATZ0682 RCX4JATZ0101 RCX6JATZ0101 JW5.0T RCX4JATZ0222 RCX4JATZ0101 RCX6JATZ0101 JW5.0T RCX4JATZ0332 RCX4JATZ0563 RCX4JATZ0102 RCX6JATZ0102 JW5.0T JW5.0T RCX4JATZ0682 RCX4JATZ0103 RCX4JATZ0471 RCX6JATZ0471 JW5.0T RCX4JATZ0273 RCX4JATZ0333 RCX4JATZ0221 RCX6JATZ0221 RCX4JATZ0221 RCX6JATZ0221 RCX4JATZ0221 RCX6JATZ0221 RCX4JATZ0472 RCX4JATZ0101 RCX6JATZ0101 RCX4JATZ0562 JW5.0T RCX4JATZ0332 RCX4JATZ0153 RCX4JATZ0682 RCX4JATZ0103 RCX4JATZ0103 RCX4JATZ0103 RCX4JATZ0472 RCX4JATZ0472 RCX4JATZ0221 RCX6JATZ0221 RCX4JATZ0471 RCX6JATZ0471 RCX4JATZ0103 RCX4JATZ0103 RCX4JATZ0103 RCX4JATZ0103 RCX4JATZ0103 RCX4JATZ0103 RCX4JATZ0223 RCX4JATZ0681 RCX6JATZ0681 RCX4JATZ0681 RCX6JATZ0681 RCX4JATZ0681 RCX6JATZ0681

Ref. No.
R527# R530 R531 R532 R533 R534 R535 R536 R537 R538 R540 R541 R542 R543 R544 R549# # R550# # R551 R552# # R553 R554 R555 R556 R557 R558 R559 R560 R561 R562 R563 R564 R565 R566 R568 R569 R571# # R572# # R575# # R576# # R577# # R578 R579 R581

Description
CARBON RES. 1/4W J 6.8k CARBON RES. 1/4W J 22k CARBON RES. 1/4W J 22k CARBON RES. 1/4W J 1.8k CARBON RES. 1/4W J 3.3 or CARBON RES. 1/6W J 3.3 CARBON RES. 1/4W J 22k CARBON RES. 1/4W J 2.7k CARBON RES. 1/4W J 470 or CARBON RES. 1/6W J 470 CARBON RES. 1/4W J 68k CARBON RES. 1/4W J 22k CARBON RES. 1/4W J 1.8k CARBON RES. 1/4W J 1.8k CARBON RES. 1/4W J 2.7 or CARBON RES. 1/6W J 2.7 CARBON RES. 1/4W J 2.7 or CARBON RES. 1/6W J 2.7 CARBON RES. 1/4W J 2.7 or CARBON RES. 1/6W J 2.7 METAL OXIDE FILM RES. 1W J 12 or METAL OXIDE FILM RES. 1W J 12 METAL OXIDE FILM RES. 1W J 12 or METAL OXIDE FILM RES. 1W J 12 METAL OXIDE FILM RES. 2W J 680 or METAL OXIDE FILM RES. 2W J 680 METAL OXIDE FILM RES. 2W J 8.2 or METAL OXIDE FILM RES. 2W J 8.2 CARBON RES. 1/4W J 2.2k CARBON RES. 1/4W J 3.3k CARBON RES. 1/4W J 2.2k CARBON RES. 1/4W J 47k CARBON RES. 1/4W J 18k CARBON RES. 1/4W J 220 or CARBON RES. 1/6W J 220 CARBON RES. 1/4W J 6.8k CARBON RES. 1/4W J 2.2k CARBON RES. 1/4W J 1.2k CARBON RES. 1/4W J 100k CARBON RES. 1/4W J 10k CARBON RES. 1/4W J 150k CARBON RES. 1/4W J 22k CARBON RES. 1/4W J 8.2k CARBON RES. 1/4W J 1k or CARBON RES. 1/6W J 1k CARBON RES. 1/4W J 2.7k METAL RESISTOR 2W J 1.8k or METAL OXIDE FILM RES. 2W J 1.8k METAL RESISTOR 2W J 1.8k or METAL OXIDE FILM RES. 2W J 1.8k CARBON RES. 1/4W J 15 or CARBON RES. 1/6W J 15 CARBON RES. 1/4W J 15 or CARBON RES. 1/6W J 15 CARBON RES. 1/4W J 15 or CARBON RES. 1/6W J 15 CARBON RES. 1/4W J 330 or CARBON RES. 1/6W J 330 CARBON RES. 1/4W J 1k or CARBON RES. 1/6W J 1k PCB JUMPER D0.6-P5.0

Part No.
RCX4JATZ0682 RCX4JATZ0223 RCX4JATZ0223 RCX4JATZ0182 RCX4JATZ03R3 RCX6JATZ03R3 RCX4JATZ0223 RCX4JATZ0272 RCX4JATZ0471 RCX6JATZ0471 RCX4JATZ0683 RCX4JATZ0223 RCX4JATZ0182 RCX4JATZ0182 RCX4JATZ02R7 RCX6JATZ02R7 RCX4JATZ02R7 RCX6JATZ02R7 RCX4JATZ02R7 RCX6JATZ02R7 RN01120ZU001 RN01200DP003 RN01120ZU001 RN01200DP003 RN02681ZU001 RN02681DP004 RN028R2ZU001 RN028R2DP004 RCX4JATZ0222 RCX4JATZ0332 RCX4JATZ0222 RCX4JATZ0473 RCX4JATZ0183 RCX4JATZ0221 RCX6JATZ0221 RCX4JATZ0682 RCX4JATZ0222 RCX4JATZ0122 RCX4JATZ0104 RCX4JATZ0103 RCX4JATZ0154 RCX4JATZ0223 RCX4JATZ0822 RCX4JATZ0102 RCX6JATZ0102 RCX4JATZ0272 RN02182ZU001 RN02182DP004 RN02182ZU001 RN02182DP004 RCX4JATZ0150 RCX6JATZ0150 RCX4JATZ0150 RCX6JATZ0150 RCX4JATZ0150 RCX6JATZ0150 RCX4JATZ0331 RCX6JATZ0331 RCX4JATZ0102 RCX6JATZ0102 JW5.0T

20030318

13-7

L6550EL

Ref. No.
R583# # R584# # R585 R586 R587# R588 R589 R590 R591# R592# R593# R594# R595 R596 R597 R598# R599# R601# # R602# R603 R604 R605 R611 R612 R613# # R614 R616 R617 R620 R621 R623 R624 R626 R642 R643 R653 R654# R655# # R656# R657# R658 R660 R661# R662# R664# R665#

Description
METAL OXIDE FILM RES. 2W J 2.2 or METAL OXIDE FILM RES. 2W J 2.2 CARBON RES. 1/4W J 1k or CARBON RES. 1/6W J 1k CARBON RES. 1/4W J 22k CARBON RES. 1/4W J 180k CARBON RES. 1/4W J 56k CARBON RES. 1/4W J 56k CARBON RES. 1/4W J 10k CARBON RES. 1/4W J 12k CARBON RES. 1/4W J 220k CARBON RES. 1/4W J 180k CARBON RES. 1/4W J 100k CARBON RES. 1/4W J 68k CARBON RES. 1/4W J 1k or CARBON RES. 1/6W J 1k CARBON RES. 1/4W J 100 or CARBON RES. 1/6W J 100 CARBON RES. 1/4W J 8.2k CARBON RES. 1/4W J 47k CARBON RES. 1/4W J 22k CEMENT RES. 5W K 0.56 or CEMENT RES. 5W K 0.56 CARBON RES. 1/4W J 820k CARBON RES. 1/4W J 820k CARBON RES. 1/4W J 820k CARBON RES. 1/4W J 820k CARBON RES. 1/4W J 220 or CARBON RES. 1/6W J 220 CARBON RES. 1/4W J 220 or CARBON RES. 1/6W J 220 CEMENT RES. 5W K 0.27 or CEMENT RESISTOR 5W K 0.27 CARBON RES. 1/4W J 47 or CARBON RES. 1/6W J 47 CARBON RES. 1/4W J 10k CARBON RES. 1/4W J 47 or CARBON RES. 1/6W J 47 CARBON RES. 1/4W J 100 or CARBON RES. 1/6W J 100 CARBON RES. 1/4W J 1.2k CARBON RES. 1/4W J 39 or CARBON RES. 1/6W J 39 PCB JUMPER D0.6-P5.0 CARBON RES. 1/4W J 390 or CARBON RES. 1/6W J 390 CARBON RES. 1/4W J 22k CARBON RES. 1/4W J 120k CARBON RES. 1/4W J 18k CARBON RES. 1/4W J 1.8k CARBON RES. 1/4W J 1k or CARBON RES. 1/6W J 1k CARBON RES. 1/4W J 15k CARBON RES. 1/4W J 15k CARBON RES. 1/4W J 470k CARBON RES. 1/4W J 1k or CARBON RES. 1/6W J 1k CARBON RES. 1/4W J 68k CARBON RES. 1/4W J 82k CARBON RES. 1/4W J 12k CARBON RES. 1/4W J 5.6k

Part No.
RN022R2ZU001 RN022R2DP004 RCX4JATZ0102 RCX6JATZ0102 RCX4JATZ0223 RCX4JATZ0184 RCX4JATZ0563 RCX4JATZ0563 RCX4JATZ0103 RCX4JATZ0123 RCX4JATZ0224 RCX4JATZ0184 RCX4JATZ0104 RCX4JATZ0683 RCX4JATZ0102 RCX6JATZ0102 RCX4JATZ0101 RCX6JATZ0101 RCX4JATZ0822 RCX4JATZ0473 RCX4JATZ0223 RW05R56DP007 RW05R56PG001 RCX4JATZ0824 RCX4JATZ0824 RCX4JATZ0824 RCX4JATZ0824 RCX4JATZ0221 RCX6JATZ0221 RCX4JATZ0221 RCX6JATZ0221 RW05R27DP005 RW05R27PG001 RCX4JATZ0470 RCX6JATZ0470 RCX4JATZ0103 RCX4JATZ0470 RCX6JATZ0470 RCX4JATZ0101 RCX6JATZ0101 RCX4JATZ0122 RCX4JATZ0390 RCX6JATZ0390 JW5.0T RCX4JATZ0391 RCX6JATZ0391 RCX4JATZ0223 RCX4JATZ0124 RCX4JATZ0183 RCX4JATZ0182 RCX4JATZ0102 RCX6JATZ0102 RCX4JATZ0153 RCX4JATZ0153 RCX4JATZ0474 RCX4JATZ0102 RCX6JATZ0102 RCX4JATZ0683 RCX4JATZ0823 RCX4JATZ0123 RCX4JATZ0562

Ref. No.
R666# # R667# R668# R669# R670# R671 R672 R673 R675# R676 R677 R678 R681 R682# # R683# # R684 R685 R686# # R687# # R691 R696 R701 R702 R703 R711 R712 R713 R721 R722 R723 R771 R772 R773 R774 R776 R777 R801

Description
METAL RESISTOR 2W J 18k or METAL OXIDE FILM RES. 2W J 18k CARBON RES. 1/4W J 27k CARBON RES. 1/4W J 33k CARBON RES. 1/4W J 27k CARBON RES. 1/4W J 100k CARBON RES. 1/4W J 3.3k CARBON RES. 1/4W J 3.3k CARBON RES. 1/4W J 100k CARBON RES. 1/4W J 22k CARBON RES. 1/4W J 10k CARBON RES. 1/4W J 68k CARBON RES. 1/4W J 47k CARBON RES. 1/4W J 12 or CARBON RES. 1/6W J 12 METAL OXIDE FILM RES. 1W J 47 or METAL OXIDE FILM RES. 1W J 47 METAL OXIDE FILM RES. 1W J 39 or METAL OXIDE FILM RES. 1W J 39 CARBON RES. 1/4W J 56 or CARBON RES. 1/6W J 56 CARBON RES. 1/4W J 56 or CARBON RES. 1/6W J 56 CARBON RES. 1/4W J 100 or CARBON RES. 1/6W J 100 CARBON RES. 1/4W J 100 or CARBON RES. 1/6W J 100 CARBON RES. 1/4W J 15k CARBON RES. 1/4W J 10 or CARBON RES. 1/6W J 10 CARBON RES. 1/4W J 75 or CARBON RES. 1/6W J 75 PCB JUMPER D0.6-P5.0 PCB JUMPER D0.6-P5.0 CARBON RES. 1/4W J 47k CARBON RES. 1/4W J 3.9k CARBON RES. 1/4W J 39k CARBON RES. 1/4W J 47k CARBON RES. 1/4W J 3.9k CARBON RES. 1/4W J 39k CARBON RES. 1/4W J 27k CARBON RES. 1/4W J 100 or CARBON RES. 1/6W J 100 CARBON RES. 1/4W J 68k CARBON RES. 1/4W J 68k CARBON RES. 1/4W J 27k CARBON RES. 1/4W J 100 or CARBON RES. 1/6W J 100 CARBON RES. 1/2W J 100 or CARBON RES. 1/2W J 100 or CARBON RES. 1/2W J 100

Part No.
RN02183ZU001 RN02183DP004 RCX4JATZ0273 RCX4JATZ0333 RCX4JATZ0273 RCX4JATZ0104 RCX4JATZ0332 RCX4JATZ0332 RCX4JATZ0104 RCX4JATZ0223 RCX4JATZ0103 RCX4JATZ0683 RCX4JATZ0473 RCX4JATZ0120 RCX6JATZ0120 RN01470ZU001 RN01470DP003 RN01390ZU001 RN01390DP003 RCX4JATZ0560 RCX6JATZ0560 RCX4JATZ0560 RCX6JATZ0560 RCX4JATZ0101 RCX6JATZ0101 RCX4JATZ0101 RCX6JATZ0101 RCX4JATZ0153 RCX4JATZ0100 RCX6JATZ0100 RCX4JATZ0750 RCX6JATZ0750 JW5.0T JW5.0T RCX4JATZ0473 RCX4JATZ0392 RCX4JATZ0393 RCX4JATZ0473 RCX4JATZ0392 RCX4JATZ0393 RCX4JATZ0273 RCX4JATZ0101 RCX6JATZ0101 RCX4JATZ0683 RCX4JATZ0683 RCX4JATZ0273 RCX4JATZ0101 RCX6JATZ0101 RCX2JZQZ0101 RCX2101KA013 RCX2JZPZ0101 RCX2JZQZ0101 RCX2101KA013 RCX2JZPZ0101 RCX4JATZ0101 RCX6JATZ0101 RCX4JATZ0101 RCX6JATZ0101 JW5.0T JW5.0T RCX4JATZ0182

R802

CARBON RES. 1/2W J 100 or CARBON RES. 1/2W J 100 or CARBON RES. 1/2W J 100

R803 R804 R811 R812 R817

CARBON RES. 1/4W J 100 or CARBON RES. 1/6W J 100 CARBON RES. 1/4W J 100 or CARBON RES. 1/6W J 100 PCB JUMPER D0.6-P5.0 PCB JUMPER D0.6-P5.0 CARBON RES. 1/4W J 1.8k

20030318

13-8

L6550EL

Ref. No.
R818 R828 R829 R831 R832 R833 R834 R837 R838 R841 R843# R845 R846# SW101

Description
CARBON RES. 1/4W J 27k CARBON RES. 1/4W J 22k CARBON RES. 1/4W J 1k or CARBON RES. 1/6W J 1k CARBON RES. 1/4W J 680 or CARBON RES. 1/6W J 680 CARBON RES. 1/4W J 22k CARBON RES. 1/4W J 2.2k CARBON RES. 1/4W J 10k PCB JUMPER D0.6-P5.0 CARBON RES. 1/4W J 1k or CARBON RES. 1/6W J 1k METAL RESISTER. 2W J 2.7 or METAL OXIDE FILM RES. 2W J 2.7 CARBON RES. 1/4W J 2.2k CARBON RES. 1/4W J 2.2k CARBON RES. 1/4W J 2.2k

Part No.
RCX4JATZ0273 RCX4JATZ0223 RCX4JATZ0102 RCX6JATZ0102 RCX4JATZ0681 RCX6JATZ0681 RCX4JATZ0223 RCX4JATZ0222 RCX4JATZ0103 JW5.0T RCX4JATZ0102 RCX6JATZ0102 RN022R7ZU001 RN022R7DP004 RCX4JATZ0222 RCX4JATZ0222 RCX4JATZ0222 SST0101AL038 SST0101HH003 SST0101AL029 SST0101AL038 SST0101HH003 SST0101AL029 SST0101AL038 SST0101HH003 SST0101AL029 SST0101AL038 SST0101HH003 SST0101AL029 SST0101AL038 SST0101HH003 SST0101AL029 SST0101AL038 SST0101HH003 SST0101AL029 WAC0172LW007 0EM407654 0EM407653 0EM407649 0EM407651 LLBF00STU026 LLBF00ZTU021 LLBF00ZTU021 LLBF00ZTU021 LLBF00ZTU021 LLBF00ZTU021 JW5.0T JW5.0T LLBF00ZTU021 LLBF00ZTU021 FBE455PMR003 FBE455PMS002 FBB455PMR004 FBB455PMS001 WX3001A6FF04 WX1L1200-102 WX1L1200-103 PAGJ20CAG402

Ref. No.
# # FH601

Description
FUSE STC4A125V U/CT or FUSE 4.00A/125V FUSE HOLDER MSF-015 or FUSE HOLDER FH-V-03078 or HOLDER, FUSE CNT41-0014

Part No.
PAGE20CW3402 PAGG20CNG402 XH01Z00LY001 XH01Z00DK001 1790424 XH01Z00LY001 XH01Z00DK001 1790424 FAZ000LD6005

FH602

FUSE HOLDER MSF-015 or FUSE HOLDER FH-V-03078 or HOLDER, FUSE CNT41-0014

GP641# JK701

GAP. FNR-G3.10D

RCA JACK 1P(YELLOW)WITH SWITCH AV1-09S- JYRL010RP009 3 or RCA JACK(YELLOW) MTJ-032-06A-20 JYRL010LY013 JYRL010RP010 JYRL010LY015 JYRL010LY014 JYRL030LY008 JYSL020LY002 JW5.0T JW5.0T JW5.0T JW5.0T JW5.0T JW5.0T GBMB3080 GBMB3080 GBMB3080 GBMB3080 JW5.0T QNZZ45BL7R0A USESJRSUNT02 USESJRSKK032 USESJRSKK034 MRNDC12QN014 MRNDC12KB002 MRNDC12MS013 NVQZ07D471KB NVQZR07D471K QVQZ0AVRS07D NVQZVR07N471 QVQZ0471D07A FBB456PMR008 LTF00CPP1018 LTF00CPXB037 LTF00CPS2051 LTH00CPSA003 LTT00CPKT102 LTT00CPSA134 JW5.0T JW12.5T JW10.0T JW10.0T JW5.0T JW5.0T JW10.0T UTUNNTUAL032 VRCB303KA011 VRCB303HH014 VRCB502KA011 VRCB502HH014 RCA JACK 1P(WHITE)WITH SWITCH AV1-09S-4 or RCA JACK(WHITE) MTJ-032-06A-22

JK702

JK703 JK704 JK801 JS102 JS104 JS342 JS704 JS706 JS855 L1

RCA JACK 1P(RED)WITH SW ITCH AV1-09S-2 or JYRL010RP008 RCA JACK(RED) MTJ-032-06A-21 RCA JACK 3P (SW) MSP-213-V2-432 HEADPHONE JACK MSJ-035-10A B PCB JUMPER D0.6-P5.0 PCB JUMPER D0.6-P5.0 PCB JUMPER D0.6-P5.0 PCB JUMPER D0.6-P5.0 PCB JUMPER D0.6-P5.0 PCB JUMPER D0.6-P5.0 SCREW, B-TIGHT M3X8 BIND HEAD+ or SCREW, B-TIGHT M3X8 BIND HEAD+ or SCREW, B-TIGHT M3X8 BIND HEAD+ or SCREW, B-TIGHT M3X8 BIND HEAD+ or PCB JUMPER D0.6-P5.0

SWITCHES
TACT SWITCH SKQSAB or TACT SWITCH KSM0612B or TACT SWITCH SKHHAM SW102 TACT SWITCH SKQSAB or TACT SWITCH KSM0612B or TACT SWITCH SKHHAM SW103 TACT SWITCH SKQSAB or TACT SWITCH KSM0612B or TACT SWITCH SKHHAM SW104 TACT SWITCH SKQSAB or TACT SWITCH KSM0612B or TACT SWITCH SKHHAM SW105 TACT SWITCH SKQSAB or TACT SWITCH KSM0612B or TACT SWITCH SKHHAM SW106 TACT SWITCH SKQSAB or TACT SWITCH KSM0612B or TACT SWITCH SKHHAM

PS691# RCV101

THERMISTOR ZPB45BL7R0A REMOCON RECEIVE UNIT MIM-93M8DKL or REMOCON RECEIVE UNIT PIC-26042SR-2 or REMOCON RECEIVE UNIT PIC-37042SR

RL601# # # SA601# # # # # SF1 T571# # # T572# T601# # TH551 TP300 TP301 TP302 TP591 TP592 TP601 TU1 VR561 VR562

POWER RELAY SDT-S-112LMR or POWER RELAY RPEF-12-901 or RELAY ALKS321 SURGE ABSORBER PVR-07D471KB or SURGE ABSORBER CNR-07D471K or SURGE ABSORBER AVR-S07D471KAAS or SURGE ABSORBER JVR-07N471K or VARISTOR ENC471D-07A SAW FILTER SAFGM45M7VHHzC0B03 FLYBACK TRANS BSC25-0220 or FLYBACK TRANSFORMER JF0501-2188 or FLYBACK TRANS BSC21-2045S HORIZONTAL DRAIVE TRANS CSA-LF161 SWITCHING TRANS 02711 or SWITCHING TRANS CSA-SW0197 PCB JUMPER D0.6-P5.0 PCB JUMPER D0.6-P12.5 PCB JUMPER D0.6-P10.0 PCB JUMPER D0.6-P10.0 PCB JUMPER D0.6-P5.0 PCB JUMPER D0.6-P5.0 PCB JUMPER D0.6-P10.0 TUNER UNIT TEQH9-001A CARBON P.O.T. 30k B or CARBON P.O.T. 30k B CARBON P.O.T. 5k B or CARBON P.O.T. 5k B

MISCELLANEOUS
AC601# B1 B2 B3 B4 BC571 BC601 BC602 BC650 BC651 BC652 BC653 BC655 BC691 BC692 CF31 CF32 CLN1 CLN301 CLN501 F601# AC CORD LA-2413 HEAT SINK(PHI) L6600UZ HEAT SINK(PHH)ASSEMBLY L6600UZ HEAT SINK(PHF)ASSEMBLY L6600UZ HEAT SINK(PHG)ASSEMBLY L6600UZ BEAD INDUCTORS FBA04HA600VB-00 BEAD INDUCTORS FBR07HA121TB-00 BEAD INDUCTORS FBR07HA121TB-00 BEAD INDUCTORS FBR07HA121TB-00 BEAD INDUCTORS FBR07HA121TB-00 BEAD INDUCTORS FBR07HA121TB-00 PCB JUMPER D0.6-P5.0 PCB JUMPER D0.6-P5.0 BEAD INDUCTORS FBR07HA121TB-00 BEAD INDUCTORS FBR07HA121TB-00 CERAMIC TRAP 4.5MHz or CERAMIC TRAP 4.5MHz CERAMIC FILTER SFSRA4M50CF00-B0 or CERAMIC FILTER 4.5MHz WIRE 040/BLA/AWG26#1007 WIRE ASSEMBLY WX1L1200-102 WIRE ASSEMBLY WX1L1200-103 FUSE 4A/125V 237 TYPE or

20030318

13-9

L6550EL

Ref. No.
VR661# # X301 X441

Description
CARBON P.O.T. 50k B or CARBON P.O.T. 50k B X'TAL 3.579545 MHz or X'TAL 3.579545MHz(30PPM) CERAMIC RESONATOR ZTB378F2 or CERAMIC RESONATOR CSB378F2

Part No.
VRCB503KA011 VRCB503HH014 FXD355LLN003 FXD355LCHE01 FY0374PLN001 FY0374PMR001

Ref. No.
R1530# # R1531 R1532 R1535 R1538 R1539 R1541 R1542 R1543

Description
METAL RESISTOR 3W J 10k or FIXED METAL OXIDE FILM RES. 3W J 10k CARBON RES. 1/4W J 1.5k CARBON RES. 1/4W J 1.5k CARBON RES. 1/4W J 2.7k CARBON RES. 1/4W J 330 or CARBON RES. 1/6W J 330 CARBON RES. 1/4W J 100 or CARBON RES. 1/6W J 100 PCB JUMPER D0.6-P5.0 PCB JUMPER D0.6-P5.0 PCB JUMPER D0.6-P5.0

Part No.
RN03103ZU001 RN03103DP005 RCX4JATZ0152 RCX4JATZ0152 RCX4JATZ0272 RCX4JATZ0331 RCX6JATZ0331 RCX4JATZ0101 RCX6JATZ0101 JW5.0T JW5.0T JW5.0T LLBF00ZTU021 JSCC290PK006 JSCC290HD012 JW5.0T JW10.0T JW10.0T

CRT CBA
Ref. No. Description
CRT CBA Consists of the following

Part No.
------------

CAPACITORS
C1501 CERAMIC CAP. B K 1000pF/2KV or CERAMIC CAP. B K 1000pF/2KV or CERAMIC CAP. 1000pF/2KV C1502 C1511 C1521 C1531 CN1501 D1511 D1521 D1531 ELECTROLYTIC CAP. 47F/16V M or ELECTROLYTIC CAP. 47F/16V M CERAMIC CAP.(AX) B K 470pF/50V CERAMIC CAP.(AX) B K 470pF/50V CERAMIC CAP.(AX) B K 470pF/50V CCD3DKD0B102 CCD3DKP0B102 CA3D102PAN04 CE1CMASTL470 CE1CMASDL470 CCA1JKT0B471 CCA1JKT0B471 CCA1JKT0B471 JTEA001TG001 QDTZ001SS133 NDTZ001N4148 QDTZ001SS133 NDTZ001N4148 QDTZ001SS133 NDTZ001N4148 JW5.0T JW5.0T JW5.0T NQWY0KTC3503 QQ9Z02SC3619 NQWY0KTC3503 QQ9Z02SC3619 NQWY0KTC3503 QQ9Z02SC3619 RN03103ZU001 RN03103DP005 RCX4JATZ0152 RCX4JATZ0152 RCX4JATZ0272 RCX4JATZ0331 RCX6JATZ0331 RCX4JATZ0101 RCX6JATZ0101 RN03103ZU001 RN03103DP005 RCX4JATZ0152 RCX4JATZ0152 RCX4JATZ0272 RCX4JATZ0331 RCX6JATZ0331 RCX4JATZ0101 RCX6JATZ0101 BC1501 # JS1551 TP1501 TP1502

MISCELLANEOUS
BEAD INDUCTORS FBR07HA121TB-00 CRT SOCKET HPS0521-012212 PCB JUMPER D0.6-P5.0 PCB JUMPER D0.6-P10.0 PCB JUMPER D0.6-P10.0 JK1501# CRT SOCKET ISHS40ST or

CONNECTOR
PIN CONNECTOR 005P-5100

DIODES
SWITCHING DIODE 1SS133(T-77) or SWITCHING DIODE 1N4148 SWITCHING DIODE 1SS133(T-77) or SWITCHING DIODE 1N4148 SWITCHING DIODE 1SS133(T-77) or SWITCHING DIODE 1N4148

COILS
L1511 L1521 L1531 Q1512 Q1522 Q1532 PCB JUMPER D0.6-P5.0 PCB JUMPER D0.6-P5.0 PCB JUMPER D0.6-P5.0

TRANSISTORS
TRANSISTOR KTC3503Y or TRANSISTOR 2SC3619 TRANSISTOR KTC3503Y or TRANSISTOR 2SC3619 TRANSISTOR KTC3503Y or TRANSISTOR 2SC3619

RESISTORS
R1510# # R1511 R1512 R1515 R1518 R1519 R1520# # R1521 R1522 R1525 R1528 R1529 METAL RESISTOR 3W J 10k or FIXED METAL OXIDE FILM RES. 3W J 10k CARBON RES. 1/4W J 1.5k CARBON RES. 1/4W J 1.5k CARBON RES. 1/4W J 2.7k CARBON RES. 1/4W J 330 or CARBON RES. 1/6W J 330 CARBON RES. 1/4W J 100 or CARBON RES. 1/6W J 100 METAL RESISTOR 3W J 10k or FIXED METAL OXIDE FILM RES. 3W J 10k CARBON RES. 1/4W J 1.5k CARBON RES. 1/4W J 1.5k CARBON RES. 1/4W J 2.7k CARBON RES. 1/4W J 330 or CARBON RES. 1/6W J 330 CARBON RES. 1/4W J 100 or CARBON RES. 1/6W J 100

20030318

13-10

L6550EL

SRT2223X L6550UA Printed in Japan 2003-04-04 HO