Pec Resistance Catalogue

PRECISION ELECTRONIC COMPONENTS MFG. CO.
WIREWOUND RESISTORS/DATA SHEET

PPR SERIES
COMMITTED TO QUALITY
PROFESSIONAL, POWER AND M ILITARY A PPLICATIONS.
SILICONE COATED. RADIAL .
* HIGHLY STABLE
* M EETS DEFENCE STANDARDS
* T APPED, A DJUSTABLE, NON-INDUCTIVE AND
INSULATED T YPES
* REFERENCE STANDARDS
- IS 8909
- JSS 50402 [RFHT-2]
- MIL-R-26 [CHARACTERISTIC V]
PPR Series wirewound resistors are designed to stringent Defence requirements. Insulated types can also be supplied if required.
specifications. They are rated to a maximum hot spot temperature of Tapped, Adjustable and Non-Inductive resistors can be supplied on
350C and fully meet the requirements of the specifications listed. request.
The stability of the resistors in this series far exceeds the specification
S PECIFICATIONS
T OLERANCE
T EMP . COEFF.
OF RESISTANCE [TCR]
POWER RATING
: FOR VALUES > 1R0 - 5%

FOR VALUES < 1R0 - 10% OR 0R05 OR WHICHEVER IS GREATER
FOR T APPED/A DJUSTABLE/N ON-INDUCTIVE VALUES - 10%
OTHER TOLERANCES ON REQUEST
: 50PPM/C - JSS LIMIT = 200PPM/C : MIL LIMIT = 260PPM/C
[IN LOWER VALUES HIGHER TCR WIRES MAY BE USED]
: RATED AT 70C AMBIENT AND DERATED LINEARLY TO ZERO AT 350C IN HORIZONTAL OR VERTICAL MOUNTING
WITH BLOCKED ENDS(FIG .4).
M AX. VOLTAGE APPLICABLE AS PER SPECIFIICATION OR PR WHICH EVER IS LOWER.
IN TAPPED RESISTORS, THE POWER HANDLING CAPACITY IS REDUCED BY APPROXIMATELY 10% PER TAP.
T HE POWER PER TAPPED RESISTOR WILL BE IN PROPORTION TO THE LENGTH OF THE TAP AND THE OVERALL LENGTH
OF THE RESISTOR.
IN ADJUSTABLE RESISTORS, POWER IS PROPORTIONAL TO THE SETTING.
DESIGN ENGINEERS SHOULD ENSURE THAT THE DISSIPATION DOES NOT EXCEED THE RATINGS. T HE BEST
METHOD IS TO
TREAT THE FULL RESISTOR AS A CURRENT LIMITED DEVICE AND ARRIVE AT THE MAXIMUM POWER FOR THE VALUE SET.
T EMP . RISE FOR HIGH WATTAGE RESISTORS : A GRAPH OF RISE IN TEMPERATURE WITH INCREASING POWER DISSIPATION IS GIVEN FOR PPR200
(FIG.1). A LSO SHOWN IN FIG.2 IS A TYPICAL TEMPERATURE DISTRIBUTION OVER THE LENGTH OF THE RESISTOR (269MM FOR PPR200) AFTER ONE
HOUR OF STABILIZED CURRENT FLOW AT AN AMBIENT OF 40C.
FIG.1
LOAD LIFE STABILITY
M OISTURE RESISTANCE
CLIMATIC SEVERITY
STEADY STATE ACCELERATION
FIG.2
: < 3%
: < 2%
: H13
: A12 1000 M/ S2
T EMPERATURE CATEGORY : T 55/200

T HERMAL SHOCK
: -60C TO +350C
LOW A IR PRESSURE
: P19, 1 KPA
VIBRATION
: V11, 10 TO 500HZ; 100 M/ S2
0894/RA03/DS/1-4
1-3-1031, L OWER T ANK BUND ROAD, KAVADIGUDA, HYDERABAD 500380, A NDHRA P RADESH, INDIA
T ELEPHONES: 613432, 613476, 612090 F AX: (91-(0)40) 613619, 230281
T ELEX: (81-(0)425) 6291 PECO IN T ELEGRAM: POTMETER
Do not scale drawings.

Dimensions in mm unless otherwise specified.
Specifications subject to change.
TABLE 2 : PPR S ERIES - A LTERNATE TERMINATIONS AVAILABLE
DIMENSIONS IN MM [IN]
[ PLEASE SEE T ABLE 1 FOR DETAILS.]
A LL PPR
HOLE
DIA.
d1
0.10
[0.004]
CLAMP
0.50
[0.020]
CLAMP
W IDTH
W
0.20
[0.008]
19.00
[0.748]
4.00
[0.157]
2.20
[0.086]
0.55
[0.022]
19.00
[0.748]
10.00
[0.394]
5.00
[0.197]
1.20
[0.047]
33.00
[1.299]
12.70
[0.500]
5.50
[0.217]
1.20
[0.047]
TYPES FOR
FIG.3A
WHICH "D"=
THICKNESS
t
0.10
[0.004]
T OL. [MM]
T OL. [IN]
FIG.3B
FIG.7
NOTE ON MOUNTING
FIG.4
The recommended method of mounting is shown in the Figure.

PEC supplies mounting hardware for use with resistors of various
wattages and for mounting from one to six resistors in a single
frame.
FOR ALL PPR TYPES EXCEPT PPR500.
L1 = L + 26.00 MM /1.024 IN :
FOR PPR500.
L1 = L + 40.00 MM /1.575 IN :
H = 22.50 MM /0.886 IN
H = 70.00 MM /2.756 IN
FIG.8
FIG.5
FIG .6
T HREADED RESISTORS:
A HEAVY DUTY RESISTOR CAPABLEOF 300WDISSIPATION SPECIALLY
DESIGNED FOR TRACTION APPLICATIONS IS AVAILABLE.
PPR SERIES
0894/RA03/DS/2-4
TABLE 1 : PPR S ERIES - D IMENSION DETAILS - R ESISTANCE RANGE (PLEASE REFER FIG .3 5 ,FIG .3 A & 3 B .)
PEC
RATING
DIMENSIONS IN MM [IN.]
RESISTANCE
T YPE
L
D
d
W
H
t
d1
RANGE
3.004 1.00
1.004 0.20
3.00
M AX.
M IN.
OHMS
[0.118]4 [0.039] [0.039]4 [0.008] [0.118]
M IN. M AX.
JSS
MIL
IS
PPR04
4W
20.00
[0.787]
9.50
[0.374]
4.50
4.00
[0.177] [0.157]
8.00
[0.315]
0.55
[0.022]
2.20
[0.086]
0R1
1K5
PPR05
5W
25.00
[0.984]
9.50
[0.374]
4.50
4.00
[0.177] [0.157]
8.00
[0.315]
0.55
[0.022]
2.20
[0.086]
0R1
2K0
PPR08
8W
35.00
[1.378]
9.50
[0.374]
4.50
4.00
[0.177] [0.157]
8.00
[0.315]
0.55
[0.022]
2.20
[0.086]
0R1
3K3
PPR10
10W
45.00
[1.772]
9.50
[0.374]
4.50
4.00
[0.177] [0.157]
8.00
[0.315]
0.55
[0.022]
2.20
[0.086]
0R1
3K9
RW29
PPR10A 10W
27.001 15.001 7.702

4.002
10.00
[1.063]1 [0.591]1 [0.303]2 [0.157]2 [0.394]
0.55
[0.022]
2.20
[0.086]
0R1
2K7
RFHT2- RW30 FRP210

10
PPR15
15W
40.001 15.001 7.702

4.002
10.00
[1.575]1 [0.591]1 [0.303]2 [0.157]2 [0.394]
0.55
[0.022]
2.20
[0.086]
0R1
6K2
RFHT2- RW31 FRP215

15
PPR17
17W
51.00
[2.007]
15.00
[0.591]
7.00
4.00
[0.276] [0.157]
10.00
[0.394]
0.55
[0.022]
2.20
[0.086]
0R1
6K8
RW32
PPR20
20W
62.00
[2.441]
15.00
[0.591]
7.00
4.00
[0.276] [0.157]
10.00
[0.394]
0.55
[0.022]
2.20
[0.086]
0R1
10K
PPR25
25W
78.001 15.001 7.702

4.002
10.00
[3.070]1 [0.591]1 [0.303]2 [0.157]2 [0.394]
0.55
[0.022]
2.20
[0.086]
0R1
18K
PPR25A 25W
62.00
[2.441]
19.00
[0.748]
9.00
8.00
[0.354] [0.315]
12.00
[0.472]
1.20
[0.047]
4.50
[0.177]
0R1
12K
PPR25B 25W
50.00
[1.969]
19.00
[0.748]
9.00
8.00
[0.354] [0.315]
12.00
[0.472]
1.20
[0.047]
4.50
[0.177]
0R1
10K
PPR35
35W
75.00
[2.953]
19.00
[0.748]
9.00
8.00
[0.354] [0.315]
12.00
[0.472]
1.20
[0.047]
4.50
[0.177]
0R1
18K
PPR40
40W
100.00
[3.937]
19.00
[0.748]
9.00
8.00
[0.354] [0.315]
12.00
[0.472]
1.20
[0.047]
4.50
[0.177]
0R1
22K
PPR40A 40W
83.00
[3.268]
24.00
[0.945]
14.50
8.00
[0.571] [0.315]
15.00
[0.591]
1.20
[0.047]
4.50
[0.177]
0R1
18K
PPR50
50W
104.001 29.101 14.302 8.00

[4.094]1 [1.146]1 [0.563]2 [0.315]
15.00
[0.591]
1.20
[0.047]
4.50
[0.177]
0R1
39K
PPR60
60W
123.00
[4.842]
24.00
[0.945]
14.50
8.00
[0.571] [0.315]
15.00
[0.591]
1.20
[0.047]
4.50
[0.177]
0R1
39K
PPR75
75W
100.00
[3.937]
33.00
[1.299]
18.003 8.00
[0.709]3 [0.315]
15.00
[0.591]
1.20
[0.047]
4.50
[0.177]
0R1
39K
RW36
PPR100 100W
155.001 33.001 19.102 8.00

[6.102]1 [1.299]1 [0.752]2 [0.315]
15.00
[0.591]
1.20
[0.047]
4.50
[0.177]
0R1
91K
RFHT2- RW37 FRP2100

100
PPR100A 100W
165.00
[6.496]
19.50
8.00
[0.768] [0.315]
15.00
[0.591]
1.20
[0.047]
4.50
[0.177]
0R1
91K
PPR150 150W
205.001 33.001 19.102 8.00

[8.071]1 [1.299]1 [0.752]2 [0.315]
15.00
[0.591]
1.20
[0.047]
4.50
[0.177]
0R1
100K
RFHT2- RW38 FRP2140

140
PPR200 200W
269.001 33.001 19.102 8.00

[10.59]1 [1.299]1 [0.752]2 [0.315]
15.00
[0.591]
1.20
[0.047]
4.50
[0.177]
0R1
100K
RFHT2180
PPR300 300W
310.001 33.001 19.102 8.00

[12.20]1 [1.299]1 [0.752]2 [0.315]
15.00
[0.591]
1.20
[0.047]
4.50
[0.177]
0R1
100K
PPR500 500W
335.001 58.001 35.002 12.70

[13.19]1 [2.283]1 [1.378]2 [0.500]
20.00
[0.787]
2.50
[0.098]
5.50
[0.217]
0R1
100K
33.00
[1.299]
RFHT2- RW33 FRP225

25
RFHT2- RW35 FRP250

50
FRP2180
RW39
NOTES :
1. M AXIMUM DIMENSION. 2. M INIMUM DIMENSION. 3. T OLERANCE = 2 MM [0.079 IN.] 4. EXCEPT WHERE SPECIFIED OTHERWISE .
5. FIG 3A WHERE t = 0.55, FIG 3B FOR OTHER THICKNESSES.
0894/RA03/DS/3-4
General Notes [See Tables 1, 2 and 3 ]
1. Ref. Fig. 3: Table 1 indicates resistors with end clamps of

standard width "W". Alternate clamps are also available : please
refer Table 2.
2. "H": The height can be changed to customer requirements on
prior request.
3. Normally end clamps of brass are used. Stainless steel clamps
can be supplied on prior request.
FIG.9
TABLE 3 : PPR S ERIES - A DJUSTABLE TERMINATIONS
[FIG .7]
DIMENSIONS IN MM [IN]
[ PLEASE SEE T ABLE 1 FOR DETAILS.]
A LL PPR
4. Minimum Value: Specifications of some Standards impose

minimum value restrictions. PEC supplies down to 0R1 in the normal
course, and below this on request.
5. Maximum Value: The maximum value is based on the limitations
imposed by the Standards for Fixed and Adjustable Resistors. Values
higher than the Standards maximum can be supplied on request.
TYPES FOR
0.50
[0.020]
W
H
d
0.20
3.00
0.10
T OL. [MM]
[0.008] [0.118] [0.004] T OL. [IN]
6. Flat Resistors on elliptical formers can be supplied on request.

They are useful where space is at a premium. They are supplied with
mounting strip (Ref. Fig. 5)
9.50
[0.374]
5.00
[0.197]
12.00
[0.472]
2.20
[0.086]
7. Non-Inductive resistors are available. The maximum value

normally possible in each range is half of the maximum specified for
the resistance range.
15.00
[0.591]
5.00
[0.197]
12.00
[0.472]
2.20
[0.086]
8. Adjustable terminals available.Please refer Fig.9 Table 3.
19.00
[0.748]
5.00
[0.197]
12.00
[0.472]
2.20
[0.086]
9. Dimensions shown in Table 1 are applicable to normal fixed

resistor and may vary for tapped, adjustable, Non inductive and
some Mil. style resistors as well as those of alternate shapes and
termination.
26.00
[1.024]
8.00
[0.315]
23.00
[0.906]
4.50
[0.177]
33.00
[1.299]
10.00
[0.394]
23.00
[0.906]
5.50
[0.217]
WHICH "D"=
10. Alternate termination available on specific request are :

i) Wire type (Fig. 10) ii)Push-fit type and
III) Ferrule type (Fig. 11)
11. These resistors are not normally intended for PCB mounting. In
case mounting on a PCB, please ask for special instruction.
12. For low values larger size terminals than indicated in Table 1.
FIG .10
FIG .11
W IRE TYPE
F ERRULE TERMINATION
0894/RA03/DS/4-4

Pec Resistance Catalogue

Uploaded by

Copyright:

Available Formats

Pec Resistance Catalogue

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Pec Resistance Catalogue

Uploaded by

Copyright:

Available Formats

PRECISION ELECTRONIC COMPONENTS MFG. CO.

WIREWOUND RESISTORS/DATA SHEET

: FOR VALUES > 1R0 - 5%

T EMPERATURE CATEGORY : T 55/200

Do not scale drawings.

TABLE 2 : PPR S ERIES - A LTERNATE TERMINATIONS AVAILABLE

The recommended method of mounting is shown in the Figure.

27.001 15.001 7.702

RFHT2- RW30 FRP210

40.001 15.001 7.702

RFHT2- RW31 FRP215

78.001 15.001 7.702

104.001 29.101 14.302 8.00

155.001 33.001 19.102 8.00

RFHT2- RW37 FRP2100

205.001 33.001 19.102 8.00

RFHT2- RW38 FRP2140

269.001 33.001 19.102 8.00

310.001 33.001 19.102 8.00

335.001 58.001 35.002 12.70

RFHT2- RW33 FRP225

RFHT2- RW35 FRP250

General Notes [See Tables 1, 2 and 3 ]

1. Ref. Fig. 3: Table 1 indicates resistors with end clamps of

4. Minimum Value: Specifications of some Standards impose

6. Flat Resistors on elliptical formers can be supplied on request.

7. Non-Inductive resistors are available. The maximum value

8. Adjustable terminals available.Please refer Fig.9 Table 3.

9. Dimensions shown in Table 1 are applicable to normal fixed

10. Alternate termination available on specific request are :

You might also like