GH2 User Manual
GH2 User Manual
GH2 User Manual
DMC-GH2H/DMC-GH2K DMC-GH2
EB
VQT3A48
Dear Customer, We would like to take this opportunity to thank you for purchasing this Panasonic Digital Camera. Please read these Operating Instructions carefully and keep them handy for future reference. Please note that the actual controls and components, menu items, etc. of your Digital Camera may look somewhat different from those shown in the illustrations in these Operating Instructions. Carefully observe copyright laws. Recording of pre-recorded tapes or discs or other published or broadcast material for purposes
other than your own private use may infringe copyright laws. Even for the purpose of private use, recording of certain material may be restricted.
THE SOCKET OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. Product identification marking
Product Digital camera Battery charger Bottom Bottom Location
About the battery pack CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturers instructions. Do not heat or expose to flame. Do not leave the battery(ies) in an automobile exposed to direct sunlight for a long period of
time with doors and windows closed.
Warning Risk of fire, explosion and burns. Do not disassemble, heat above 60 xC or incinerate.
VQT3A48
IMPORTANT
The wires in this mains lead are coloured in accordance with the following code: Blue: Neutral, Brown: Live. As these colours may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured Blue must be connected to the terminal which is marked with the letter N or coloured Black or Blue. The wire which is coloured Brown must be connected to the terminal which is marked with the letter L or coloured Brown or Red. WARNING: DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL WHICH IS MARKED WITH THE LETTER E, BY THE EARTH SYMBOL OR COLOURED GREEN OR GREEN/YELLOW. THIS PLUG IS NOT WATERPROOFKEEP DRY.
CAUTION!
IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET IN YOUR HOME THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY. THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED INTO ANY 13AMPERE SOCKET. If a new plug is to be fitted please observe the wiring code as stated below. If in any doubt please consult a qualified electrician.
Before use
Remove the connector cover.
Figure B
Fuse (5 ampere)
VQT3A48
About the battery charger CAUTION! DO NOT INSTALL OR PLACE THIS UNIT IN A BOOKCASE, BUILT-IN CABINET OR IN
ANOTHER CONFINED SPACE. ENSURE THE UNIT IS WELL VENTILATED. TO PREVENT RISK OF ELECTRIC SHOCK OR FIRE HAZARD DUE TO OVERHEATING, ENSURE THAT CURTAINS AND ANY OTHER MATERIALS DO NOT OBSTRUCT THE VENTILATION VENTS. DO NOT OBSTRUCT THE UNITS VENTILATION OPENINGS WITH NEWSPAPERS, TABLECLOTHS, CURTAINS, AND SIMILAR ITEMS. DO NOT PLACE SOURCES OF NAKED FLAMES, SUCH AS LIGHTED CANDLES, ON THE UNIT. DISPOSE OF BATTERIES IN AN ENVIRONMENTALLY FRIENDLY MANNER. The primary circuit is always live as long as the power cord is connected to an electrical outlet.
The battery charger is in the standby condition when the AC power supply cord is connected.
Care of the camera Do not strongly shake or bump the camera by dropping or hitting it. Do not subject to
strong pressure. The camera may malfunction, recording pictures may become impossible, or the lens, the LCD monitor or the external case may be damaged. Be particularly careful in the following places as they may cause this unit to malfunction. Places with a lot of sand or dust. Places where water can come into contact with this unit such as when using it on a rainy day or on a beach. Do not touch the lens or the sockets with dirty hands. Also, be careful not to allow liquids, sand and other foreign matter to get into the space around the lens, buttons etc. This camera is not waterproof. If water or seawater splashes on the camera, use a dry cloth to wipe the camera body carefully. If the unit does not operate normally, please contact the dealer where you purchased the camera or the repair service centre. Do not place your hands inside the mount of the digital camera body. Since the sensor unit is a precision apparatus, it may cause a malfunction or damage.
About Condensation (When the lens, the viewfinder or LCD Monitor is fogged up) Condensation occurs when the ambient temperature or humidity changes. Be careful of If condensation occurs, turn the camera off and leave it for about 2 hours. The fog will
condensation since it causes lens and LCD monitor stains, fungus and camera malfunction. disappear naturally when the temperature of the camera becomes close to the ambient temperature.
VQT3A48
Information for Users on Collection and Disposal of Old Equipment and used Batteries These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste. For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points, in accordance with your national legislation and the Directives 2002/96/EC and 2006/ 66/EC. By disposing of these products and batteries correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling. For more information about collection and recycling of old products and batteries, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items. Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation. For business users in the European Union If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information. [Information on Disposal in other Countries outside the European Union] These symbols are only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal. Note for the battery symbol (bottom two symbol examples): This symbol might be used in combination with a chemical symbol. In this case it complies with the requirement set by the Directive for the chemical involved.
Cd
VQT3A48
Contents
Information for Your Safety....................... 2
Before Use
Accessories .............................................. 9 Names and Functions of Components ... 12 About the Lens ....................................... 19
How to set focus when recording a motion picture (Continuous AF) ....... 43 Recording Motion Picture ................. 44 Playing Back Motion Pictures ................. 46 Taking Pictures using the Automatic Function (: Intelligent Auto Mode)....... 48 Deleting Pictures .................................... 52 Setting the Menu .................................... 54 Setting menu items........................... 55 Setting the Quick Menu .......................... 56 About the Setup Menu............................ 58
Preparation
Attaching/Detaching the Lens................. 21 Attaching the Shoulder Strap.................. 23 Preparing the Battery.............................. 24 Charging the Battery ........................ 24 Inserting/Removing the Battery ........ 25 Approximate operating time and number of recordable pictures ......... 26 Preparing the Card (Optional) ................ 28 Inserting/Removing the Card (Optional) ......................................... 28 About cards that can be used with this unit............................................. 29 Approximate number of recordable pictures and operating time.............. 30 Setting Date/Time (Clock Set) ................ 31 Changing the clock setting ............... 31
Recording
Switching the Display of the LCD Monitor/Viewfinder.................................. 64 Switching the Information Displayed on the recording screen ................... 64 Taking Pictures with the Zoom ............... 67 Using the Optical Zoom/ Using the Extra Tele Conversion (EX)/Using the Digital Zoom............. 67 Taking Pictures using the Built-in Flash....................................................... 69 Switching to the appropriate flash setting............................................... 69 Adjust the flash output ...................... 74 Optical Image Stabilizer.......................... 74 Compensating the Exposure .................. 76 Taking Pictures using Burst Mode.......... 77 Taking Pictures using Auto Bracket........ 79 Taking Pictures with the Self-timer ......... 81 Setting the Method used to Focus (AF Mode)............................................... 82 Taking Pictures with Manual Focus........ 85 Fixing the Focus and the Exposure (AF/AE Lock) .......................................... 87 Adjusting the White Balance................... 88 Setting the Light Sensitivity .................... 91 Taking Pictures by Specifying the Aperture/Shutter Speed.................... 93 [] Aperture-priority AE ................... 93 [] Shutter-priority AE ..................... 93 Taking Picture by Setting the Exposure Manually ................................................. 94
Basic
Selecting the [REC] Mode ...................... 32 Taking a Still picture ............................... 34 How to set focus when taking a still picture (AFS/AFC)............................ 34 Taking Pictures with Your Favourite Settings (: Programme AE Mode) .............. 35 Taking pictures using the Touch Shutter function ................................ 38 Playing Back Pictures............................. 39 Changing the information displayed on the playback screen .................... 40 Recording Motion Picture ....................... 43
VQT3A48
Confirm the Effects of Aperture and Shutter Speed (Preview Mode)............... 96 Taking Expressive Portraits and Landscape Pictures (Advanced Scene Mode) ........................ 97 [PORTRAIT] ...............................97 [SCENERY] ................................ 98 [CLOSE-UP] ...............................98 Taking Pictures that match the Scene being recorded ( : Scene Mode) ..........99 [PERIPHERAL DEFOCUS] ........99 . [NIGHT PORTRAIT] ................. 100 / [NIGHT SCENERY].................. 100 [SUNSET].................................100 2 [PARTY] ...................................101 - [SPORTS] ................................ 101 : [BABY1]/; [BABY2] ............... 101 [PET] ........................................ 102 Taking Pictures while Adjusting Colour ( : My Colour Mode) ...........................103 Taking Pictures in Custom Mode ..........105 Selecting the Mode and Recording Motion Pictures ( : Creative Motion Picture Mode)......106 [MANUAL MOVIE MODE] ........106 [24P CINEMA] .......................... 106 [VARIABLE MOVIE MODE] ..... 107 Recording still pictures while recording motion pictures...................................... 108 Taking a Picture with Face Recognition Function ................................................109 Useful Functions at Travel Destinations .......................................... 115 Entering Text......................................... 117 Using the [REC] Mode Menu ................118 [FILM MODE] ...........................118 ? [ASPECT RATIO] ..................... 120 @ [PICTURE SIZE] ...................... 120 A [QUALITY] ................................ 121 [FACE RECOG.] ...................... 122 C [METERING MODE] ................122 [STABILIZER]...........................122 [FLASH].................................... 122 [RED-EYE REMOVAL]............. 123 [FLASH SYNCHRO]................. 123 [FLASH ADJUST.].................... 123
[I.RESOLUTION] ......................123 [I.DYNAMIC] (Intelligent dynamic range control).............124 [ISO LIMIT SET] .......................124 [LONG SHTR NR] ....................124 [EX. TELE CONV.] ...................124 ) [DIGITAL ZOOM]......................125 [BURST RATE].........................125 [AUTO BRACKET] ...................125 [ASPECT BRACKET] ...............125 [SELF-TIMER] ..........................125 [COLOR SPACE] .....................126 Using the [MOTION PICTURE] Mode Menu ...........................................127 [REC MODE] ............................127 [REC QUALITY] .......................127 [EXPOSURE MODE]................128 ! [PICTURE MODE]....................128 [CONTINUOUS AF]..................129 [WIND CUT] .............................129 B [MIC LEVEL DISP.] ..................129 [MIC LEVEL ADJ.]....................129 [REC HIGHLIGHT] ...................129 Using the [CUSTOM] Menu ..................130
Playback/Editing
Playing Back Burst Pictures..................137 Editing Burst Pictures............................138 Creating Still Pictures from a Motion Picture...................................................140 Using the [PLAYBACK] Mode Menu.....141 [2D/3D SETTINGS] ..................141 [SLIDE SHOW].........................141 [PLAYBACK MODE].................143 [TITLE EDIT] ............................144 [TEXT STAMP].........................145 [VIDEO DIVIDE] .......................146 Q [RESIZE] Reducing the picture size (number of pixels) .............147 [CROPPING] ............................148 ? [ASPECT CONV.].....................148 N [ROTATE]/ M [ROTATE DISP.] ......................149 [FAVORITE] .............................150 [PRINT SET].............................151
VQT3A48
Direct Sales at Panasonic UK For customers: 0844 844 3856 Order accessory and consumable items for
Others
Optional accessories ............................ 171 LCD Monitor Display/Viewfinder Display.................................................. 174 Cautions for Use................................... 177 Message Display .................................. 183 Troubleshooting.................................... 186 Specifications ....................................... 195
your product with ease and confidence by phoning our Customer Care Centre Monday Thursday 9.00 a.m. 5.30 p.m., Friday 9.30 a.m. 5.30 p.m. (Excluding public holidays) Or go on line through our Internet Accessory ordering application at www.pas-europe.com. Most major credit and debit cards accepted. All enquiries transactions and distribution facilities are provided directly by Panasonic UK Ltd. It couldnt be simpler! Also available through our Internet is direct shopping for a wide range of finished products, take a browse on our website for further details.
VQT3A48
Before Use
Before Use
Accessories
Check that all the accessories are supplied before using the camera. Product numbers correct as of October 2010. These may be subject to change. 1 Digital Camera Body (This is referred to as camera body in these operating instructions.) 2 Interchangeable Lens LUMIX G VARIO HD 14 140 mm/F4.0 5.8 ASPH./MEGA O.I.S. (This is referred to as lens in these operating instructions.) 3 Lens Hood 4 Lens Cap (This is attached to the interchangeable lens at the time of purchase.) 5 Lens Rear Cap (This is attached to the interchangeable lens at the time of purchase.) 6 Lens Storage Bag 7 Interchangeable Lens LUMIX G VARIO 14 42 mm/F3.5 5.6 ASPH./MEGA O.I.S. (This is referred to as lens in these operating instructions.) 8 Lens Hood 9 Lens Cap (This is attached to the interchangeable lens at the time of purchase.) 10 Lens Rear Cap (This is attached to the interchangeable lens at the time of purchase.) 11 Lens Storage Bag 12 Battery Pack (Indicated as battery pack or battery in the text) Charge the battery before use. 13 Battery Charger (Indicated as battery charger or charger in the text) 14 AC Mains Lead 15 AV Cable 16 USB Connection Cable 17 Body Cap (This is attached to the camera body at the time of purchase.) 18 CD-ROM Software: 19 Shoulder Strap 20 Stylus pen 21 Battery Case 1 Supplied in DMC-GH2H only 2 Supplied in DMC-GH2K only
text. Use it to install the software to your PC.
SD Memory Card, SDHC Memory Card and SDXC Memory Card are indicated as card in the The card is optional. Description in these operating instructions is based on the 14 42 mm/F3.5 5.6 lens supplied Consult the dealer or your nearest Service Centre if you lose the supplied accessories. (You
can purchase the accessories separately.) in DMC-GH2K.
VQT3A48
Before Use
DMC-GH2H 2 3
H-VS014140
VYC0997
2
VYF3250
VFC4315
VFC4430
DMC-GH2K 7 8
10
11
H-FS014042
VYC1009
VYF3201
VFC4315
VFC4456
12
13
14
15
16
DMW-BLC12E
DE-A80A
K2CT39A00002
K1HA14CD0004 K1HA14AD0003
17
18
19
20
21
VKF4385
VFC4602
VGQ0C14
VGQ0Q65
10
VQT3A48
Before Use
Mount Adaptor
DMW-BLC12E AC Adaptor1 DMW-AC8EB DC Coupler1 DMW-DCC8GU Zoom Lever DMW-ZL1E Flash DMW-FL220E DMW-FL360E DMW-FL500E Interchangeable Lens H-VS014140E H-FS014042E H-FS014045E H-FS045200E H-F007014E H-ES045E H-H020E H-F008E H-H014E H-FS100300E H-FT012E (Read P19 for information about other lenses that can be used.) MC Protector DMW-LMCH62E2 DMW-LMC52E3 ND Filter DMW-LND62E2 DMW-LND52E3 PL Filter (Circular Type) DMW-LPL62E2 DMW-LPL52E3 Leather Bag DMW-BAL1 Soft Bag DMW-BAG1 Soft Case DMW-CG2 Shoulder Strap DMW-SSTL1 DMW-SSTG1 DMW-SSTG2 DMW-SSTG3 DMW-SSTG5 DMW-SSTG6 Remote Shutter DMW-RSL1E Stereo Microphone DMW-MS1E HDMI mini cable RP-CDHM15E RP-CDHM30E
DMW-MA1E DMW-MA2ME DMW-MA3RE Tripod Adaptor DMW-TA1E4 SDXC Memory Card 64 GB: RP-SDW64GE1K 48 GB: RP-SDW48GE1K SDHC Memory Card 32 GB: RP-SDW32GE1K/RP-SDP32GE1K 24 GB: RP-SDP24GE1K 16 GB: RP-SDW16GE1K/RP-SDP16GE1K 8 GB: RP-SDW08GE1K/RP-SDP08GE1K/ RP-SDR08GE1A 4 GB: RP-SDW04GE1K/RP-SDP04GE1K/ RP-SDR04GE1A SD Memory Card 2 GB: RP-SDP02GE1K/RP-SDR02GE1A
VQT3A48
11
Before Use
1 2
7 6
8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 [LVF/LCD] button (P16) Diopter adjustment dial (P16) Viewfinder (P16, 64, 174) Eye sensor (P16) Playback button (P39, 46) [AF/AE LOCK] button (P87) Camera ON/OFF switch (P31) Rear dial (P18) [DISPLAY] button (P40, 64, 96) Eye Cup (P178) Touch panel/LCD monitor (P16, 39, 64, 174) [Q.MENU] button (P49, 56, 84) Delete button (P52)/ Preview button (P96) [MENU/SET] button (P17, 55) Cursor buttons (P17) 3/ISO (P91) 1/WB (White Balance) (P88) 2/Function 2 button (P18) 4/Function 3 button (P18)
9 10 11 12 13 14 15 16
17 18 19 20
21 22
12
VQT3A48
Before Use
23 Focus mode lever (P34, 43, 82, 85) 24 Auto focus mode dial Face Detection ([ ]) (P82): AF Tracking ([ ]) (P83): 23-area-focusing ([ ]) (P83): 1-area-focusing ([]) (P84): 25 Stereo microphone 26 Drive mode lever Single (P35): Burst (P77): Auto Bracket (P79): Self-timer (P81): 27 Shutter button (P35) 28 Focus distance reference mark (P86) 29 Flash open lever (P69) 30 Hot shoe (P171, 173) 31 Mode dial (P32) 32 Status indicator (P31) 33 Motion picture button (P44) 34 Function 1 button (P18) 35 [MIC/REMOTE] socket (P172, 173) 36 Shoulder strap eyelet (P23) Be sure to attach the shoulder strap when
23
MF
AFC AFS
24 25
26 27
28 29 30 31 32 33 34
37 [HDMI] socket (P158) 38 [AV OUT/DIGITAL] socket (P157, 162, 164, 167) 39 Card door (P28) 40 DC coupler cover When using an AC adaptor, ensure that the
Panasonic DC coupler (DMW-DCC8; optional) and AC adaptor (DMW-AC8E; optional) are used. (P173)
using the camera to ensure that you will not drop it.
35
36 37 38
39 40
41 Battery door (P25) 42 Release lever (P25) 43 Tripod receptacle (P182) When you use a tripod, make sure the tripod
is stable when the camera is attached to it.
41 42
43
VQT3A48
13
Before Use
Lens H-VS014140 (LUMIX G VARIO HD 14 140 mm/F4.0 5.8 ASPH./MEGA O.I.S.) 44 Tele 45 Lens surface 46 Focus ring (P85) 47 Wide 49 48 Zoom ring (P67) 49 [O.I.S.] switch (P74) 48 50 Contact point 50 44 45 46 47 51 Lens fitting mark (P21) H-FS014042 (LUMIX G VARIO 14 42 mm/F3.5 5.6 ASPH./MEGA O.I.S.) 52 Tele 53 Lens surface 54 Focus ring (P85) 55 Wide 56 Zoom ring (P67) 57 Contact point 58 Lens fitting mark (P21)
51
52
53 54 55 56
57 58
LCD Monitor At the time when this camera is purchased, the LCD monitor is stowed in the camera body. Bring out the LCD monitor as shown below.
1 Open the LCD monitor. (Maximum 180o) 2 It can be rotated 180o forward. 3 Return the monitor to its original position. Only rotate the LCD monitor after opening it wide enough, and be careful not to use
excessive force as it may be damaged.
14
VQT3A48
Before Use
The LCD monitor can be rotated to suit your needs. This is convenient as it allows you to take pictures from various angles by adjusting the LCD monitor. Do not cover the AF Assist Lamp with your fingers or other objects. Taking pictures at a high angle This is convenient when there is someone in front of you and you cannot get close to the
subject.
It can only be rotated 90o towards you. Taking pictures at a low angle This is convenient when taking pictures of flowers etc. that are in a low position.
It can be rotated 180o forward. Note When not using the LCD monitor it is recommended that you close it with the screen facing
inward to prevent dirt and scratches.
VQT3A48
15
Before Use
Viewfinder About the eye sensor automatic switching Eye sensor is active when the [AUTO SWITCH] of the [LVF/LCD SWITCH] (P134) in the [CUSTOM] menu is set to [ON], switching automatically to viewfinder display when an eye or object is moved closer to the viewfinder, and to LCD monitor display when moved away. Sensitivity of the eye sensor can be set to [LOW] or [HIGH] with [SENSITIVITY]. Eye sensor might not work properly depending on the shape of your eyeglasses, the way you The eye sensor is disabled during motion picture playback and slide show. Switching the LCD monitor/Viewfinder manually
hold the camera, or bright light shining around the eyepiece. Switch manually in that case.
Diopter adjustment Adjust the diopter to suit your vision so that you can see the characters displayed in the viewfinder clearly.
Use this to perform tasks such as selecting icons or images displayed on the touch panel. It may not operate properly when multiple
icons are touched simultaneously, so try to touch the centre of the icon.
This is used when performing tasks such as moving to the next image by dragging horizontally, or changing the range of the displayed image. This can also be used to perform tasks such as switching the screen by operating the slide bar.
16
VQT3A48
Before Use
sheet, please follow the instructions that accompany the sheet. (Some liquid crystal protection sheets may impair visibility or operability.) Apply a little extra pressure when touching if you have a commercially available protection sheet affixed or if you feel it is not responding well. Touch panel will not operate properly when the hand holding this unit is pressing on the touch panel. Do not press on the LCD monitor with hard pointed tips, such as ball point pens. Do not operate with your fingernails. Wipe the LCD monitor with dry soft cloth when it gets dirty with finger prints and others. Do not scratch or press the LCD monitor too hard. For information about the icons displayed on the touch panel, refer to LCD Monitor Display/ Viewfinder Display on P174.
About the Stylus pen It is easier to use the stylus pen (supplied) for detailed operation or if it is hard to operate with your fingers. Only use the supplied stylus pen. Do not place it where small children can reach. Cursor buttons/[MENU/SET] button This document expresses the up, down, left, and right of the cursor button as follows, or as 3/4/2/1.
or
Press 4
Even when the camera is operated using the touch panel, it is possible to operate with the cursor button and [MENU/SET] button if a guide like the one shown on the right is displayed.
Cursor button: Selection of items or setting of values etc. is performed. [MENU/SET]: Confirmation of setting contents or exit from menu is performed.
VQT3A48
17
Before Use
Rear Dial There are 2 ways to operate the rear dial, rotating left or right, and deciding by pressing. Rotating: Selection of items or setting of values is performed during the various settings. Pressing: Operations that are the same as [MENU/SET] button, such as selection of settings and exiting the menu, are performed during the various settings. Rear dial is described as follows in these operating instructions.
Function button At the time of purchase, [INTELLIGENT AUTO] is assigned to the [Fn1] button, [FILM MODE] to the 2 (Fn2) button and [METERING MODE] to the 4 (Fn3) button. The functions to be assigned can be selected from the menu below
using [Fn BUTTON SET] in the [CUSTOM] menu. [REC] menu/Recording functions
[CUSTOM] menu
[INTELLIGENT AUTO]/[FILM MODE]/ [FOCUS AREA SET]/[ASPECT RATIO]/[QUALITY]/ [1 SHOT ]/[METERING MODE]/[1 SHOT ]/ [FLASH]/[FLASH ADJUST.]/[ISO LIMIT SET]/ [EX. TELE CONV.]/[BURST RATE]/ [AUTO BRACKET]
Note Refer to P118 for details about [REC] Mode menu. Refer to P130 for details about [CUSTOM] menu. When [INTELLIGENT AUTO] is set, pushing the button will switch to Intelligent Auto Mode. When set to [FOCUS AREA SET], it is possible to display the position setting screen of either When [1 SHOT
] is set, it will record the RAW file and a fine JPEG image simultaneously once only. It will return to original quality after recording. When [1 SHOT ] is set, it will record with [METERING MODE] set to [] (spot) once only. It will return to original Metering Mode after recording. AF area or MF Assist. (Pressing the button again or turning off the camera will cancel the setting.)
18
VQT3A48
Before Use
Four Thirds mount specification lens Lens with the Four Thirds mount specification can be used by using the mount adaptor (DMW-MA1; optional).
Leica mount specification lens When you use the M mount adaptor or R mount adaptor (DMW-MA2M, DMW-MA3R; optional),
you can use Leica M Mount or Leica R Mount interchangeable lenses. For certain lenses, the actual distance at which the subject is in focus may differ slightly from the rated distance. When using a Leica lens mount adaptor, set [SHOOT W/O LENS] (P136) to [ON].
About the functions of your lens Depending on the type of lens, you may not be able to use some functions such as the
Direction Detection Function (P36), [STABILIZER] (P74), Quick AF (P131) and Continuous AF (P131). The available flash range etc. differs depending on the aperture value of the lens you are using. Take some test pictures with the lens you are using.
VQT3A48
19
Before Use
The focal length for the lens is twice that of a 35 mm film camera.
(A 50 mm lens is equivalent to a 100 mm lens.) Focal length of the 3D interchangeable lens can be checked on the following website.
Interchangeable lenses that can be used with this unit and Auto Focus/Auto Aperture Operation (As of October 2010) (: Usable, : Some functions/features limited, : Not usable)
when recording still pictures Lens type Auto Focus Auto aperture setting while recording motion pictures Auto Focus Auto aperture setting
Micro Four Thirds HD motion picture mount specification compatible lens lens supplied with the DMC-GH2H (H-VS014140) (LUMIX G VARIO HD) The Lens supplied in DMC-GH2K. (H-FS014042) The 3D interchangeable lens (H-FT012; optional) Other Micro Four Thirds mount specification lens3 Four Thirds mount Four Thirds mount specification lens1 specification lens compatible to contrast AF Four Thirds mount specification lens not compatible to contrast AF Leica mount Interchangeable specification lens2 lens for Leica
([AFS], [AFC])
4, 5
4, 5
8 ([AFS])
6, 8
1 Mount adaptor (DMW-MA1; optional) is necessary to use with this unit. 2 A Leica lens mount adaptor (DMW-MA2M or DMW-MA3R; optional) is necessary. 3 This function is not supported by some Micro Four Thirds mount specification lenses. For lens operations, please see our website. 4 When recording motion pictures, the focus is continuously adjusted for both [AFS] and [AFC] (P43). 5 AF tracking is slower than the HD motion picture compatible lens, also the sound of Auto Focus operation may be recorded. 6 Auto Focus is activated only when the shutter button is pressed halfway. The sound of Auto Focus operation may be recorded at this time. 7 The sound of Aperture operation may be recorded. 8 AF performance may differ depending on the lens used. Refer to the website for details.
Refer to catalogues/Web pages for most current information regarding compatible lenses. http://panasonic.jp/support/global/cs/dsc/ (This Site is English only.)
20
VQT3A48
Preparation
Preparation
Turn the lens rear cap A and the body cap B in the direction of the arrow to detach them.
Align the lens fitting marks C (red marks) on the camera body and the lens and then rotate the lens in the direction of the arrow until it clicks.
Do not press the lens release button D when you Do not try to attach the lens when holding it at an
angle to the camera body as the lens mount may get scratched. attach a lens.
VQT3A48
21
Preparation
Attach the lens cap. Press the lens release button D while turning the lens as far as possible in the direction of the arrow to detach it.
Always attach the body cap to the camera body so Attach the lens rear cap so that the lens contact
point does not get scratched. that dirt or dust does not get inside.
It is recommended to attach the lens cap or attach the MC Protector (optional) to protect the
lens surface when carrying. (P172)
Note
Attaching the Lens Hood In bright sunlight or backlight, the lens hood will minimise lens flare and ghosting. The lens hood cuts off excess lighting and improves the picture quality. To attach the lens hood (flower shape) that came with the lens supplied in DMC-GH2H/DMC-GH2K
Insert the lens hood into the lens with the short sides at the top and bottom, and turn in the direction of the arrow until it stops.
A Fitting to the mark.
Note When temporarily detaching and carrying the lens hood supplied
with the DMC-GH2H/DMC-GH2K, attach the lens hood to the lens in the reverse direction.
22
VQT3A48
Preparation
Pass the shoulder strap through the shoulder strap eyelet on the camera body.
A: Shoulder strap eyelet
Pass the end of the shoulder strap through the ring in the direction of the arrow and then pass it through the stopper.
Pass the end of the shoulder strap through the hole on the other side of the stopper.
Pull the other side of the shoulder strap and then check that it will not come out. Perform steps 1 to 4 and then attach
the other side of the shoulder strap.
Note Use the shoulder strap around your shoulder. Do not wrap the strap around your neck. It may result in injury or accident. Do not leave the shoulder strap where an infant can reach it. It may result in an accident by mistakenly wrapping around the neck.
VQT3A48
23
Preparation
dedicated battery (DMW-BLC12E) supports this function. The only batteries suitable for use with this unit are genuine Panasonic products and batteries manufactured by other companies and certified by Panasonic. (Batteries which do not support this function cannot be used.) Panasonic cannot in any way guarantee the quality, performance or safety of batteries which have been manufactured by other companies and are not genuine Panasonic products.
24
VQT3A48
Preparation
About the [CHARGE] indicator The [CHARGE] indicator turns on: The [CHARGE] indicator turns off: The [CHARGE] indicator A is turned on and charging will start. The [CHARGE] indicator A of the charger will turn off once the charging has completed without any problem.
When the [CHARGE] indicator flashes The battery temperature is too high or too low. It is recommended to charge the battery again The terminals of the charger or the battery are dirty. In this case, wipe them with a dry cloth. Charging time
Charging time Approx. 140 min in an ambient temperature of between 10 oC to 30 oC (50 oF to 86 oF).
The indicated charging time is for when the battery has been discharged completely.
The charging time may vary depending on how the battery has been used. The charging time for the battery in hot/cold environments or a battery that has not been used for a long time may be longer than normal.
Note Do not leave any metal items (such as clips) near the contact areas of the power plug.
Otherwise, a fire and/or electric shocks may be caused by short-circuiting or the resulting heat generated. The battery can be recharged even when it still has some charge left, but it is not recommended that the battery charge be frequently topped up while the battery is fully charged. (Since characteristic swelling may occur.)
Slide the release lever in the direction of the arrow and open the battery door.
Always use genuine Panasonic batteries If you use other batteries, we cannot guarantee
the quality of this product. (DMW-BLC12E).
Being careful about the battery orientation, insert all the way until you hear a locking sound and then check that it is locked by lever A. Pull the lever A in the direction of the arrow to remove the battery. Close the battery door, and slide the release lever.
VQT3A48
25
Preparation
Note Remove the battery after use. Store the removed battery in the battery case (supplied). The battery will be exhausted if left for a long period of time after being charged. Before removing the battery, turn the camera off, and wait until the status indicator has gone off
completely. (Otherwise, this unit may no longer operate normally and the card itself may be damaged or the recorded pictures may be lost.) The supplied battery is designed only for the camera. Do not use it with any other equipment. The battery becomes warm after using it and during and after charging. The camera also becomes warm during use. This is not a malfunction.
Recording still pictures (when using the LCD monitor) (By CIPA standard in Programme AE Mode)
When the 14 140 mm/F4.0 5.8 lens supplied in DMC-GH2H is used Number of recordable pictures Recording time Approx. 320 pictures Approx. 160 min When the 14 42 mm/F3.5 5.6 lens supplied in DMC-GH2K is used Number of recordable pictures Recording time Approx. 330 pictures Approx. 165 min
Recording still pictures (when using the viewfinder) (By CIPA standard in Programme AE Mode)
When the 14 140 mm/F4.0 5.8 lens supplied in DMC-GH2H is used Number of recordable pictures Recording time Approx. 330 pictures Approx. 165 min When the 14 42 mm/F3.5 5.6 lens supplied in DMC-GH2K is used Number of recordable pictures Recording time Approx. 340 pictures Approx. 170 min
26
VQT3A48
Preparation
Recording conditions by CIPA standard CIPA is an abbreviation of [Camera & Imaging Products Association]. Temperature: 23 oC (73.4 oF)/Humidity: 50%RH when LCD monitor is on. Using a Panasonic SD Memory Card (2 GB). Using the supplied battery. Starting recording 30 seconds after the camera is turned on. Recording once every 30 seconds with full flash every second recording. Turning the camera off every 10 recordings and leaving it until the temperature of the battery
decreases.
The number of recordable pictures varies depending on the recording interval time. If the recording interval time becomes longer, the number of recordable pictures decreases. [For example, if you were to take one picture every two minutes, then the number of pictures would be reduced to approximately one-quarter of the number of pictures given above (based upon one picture taken every 30 seconds).] Playback (when using the LCD monitor)
When the 14 140 mm/F4.0 5.8 lens supplied in DMC-GH2H is used Playback time Approx. 240 min When the 14 42 mm/F3.5 5.6 lens supplied in DMC-GH2K is used Playback time Approx. 250 min
Note The operating times and number of recordable pictures will differ according to the
environment and the operating conditions. For example, in the following cases, the operating times shorten and the number of recordable pictures is reduced. In low-temperature environments, such as on ski slopes. Using the [AUTO] of [LCD MODE] or [MODE1] of [LCD MODE] (P59). When flash is used repeatedly. When the operating time of the camera becomes extremely short even after properly charging the battery, the life of the battery may have expired. Buy a new battery.
VQT3A48
27
Preparation
Push it securely all the way until you hear a click while being careful about the direction in which you insert it. To remove the card, push the card until it clicks, then pull the card out upright.
A: Do not touch the connection terminals of the card. The card may be damaged if it is not fully inserted.
1: Close the card door. 2: Slide the card door to the end and then close it firmly.
If the card door cannot be completely closed, remove the
card, check its direction and then insert it again.
Note Always turn the camera off before opening the card door. Before removing the card, turn the camera off, and wait until the status indicator has gone off
completely. (Otherwise, this unit may no longer operate normally and the card itself may be damaged or the recorded pictures may be lost.)
28
VQT3A48
Preparation
SDHC Memory Card can be used with SDHC Memory Card SDXC Memory Card can only be used with SDXC Memory Check that the PC and other equipment are compatible when
using the SDXC Memory Cards. http://panasonic.net/avc/sdcard/information/SDXC.html Card compatible equipment. or SDXC Memory Card compatible equipment.
SDHC Memory Card (4 GB to 32 GB) SDXC Memory Card (48 GB, 64 GB)
Only cards bearing the SDHC logo (indicating that the card conforms to SD video standards) Only cards bearing the SDXC logo (indicating that the card conforms to SD video standards) Use a card with SD Speed Class with Class 4 or higher when recording motion pictures in
may be used as 48 GB and 64 GB cards. [AVCHD]. Also, use a card with SD Speed Class with Class 6 or higher when recording motion pictures in [MOTION JPEG]. SD Speed Class is the speed standard regarding continuous writing. Check via the label on the card, etc. may be used as 4 GB to 32 GB cards.
e.g.: Please confirm the latest information on the following website. http://panasonic.jp/support/global/cs/dsc/
(This Site is English only.)
Access to the card The access indication lights red when pictures are being recorded on the card.
Do not turn this unit off, remove its battery or card, or disconnect the AC adaptor
(DMW-AC8E; optional) when the access indication is lit [when pictures are being written, read or deleted, or the card is being formatted (P63)]. Furthermore, do not subject the camera to vibration, impact or static electricity. The card or the data on the card may be damaged, and this unit may no longer operate normally. If operation fails due to vibration, impact or static electricity, perform the operation again.
Note Write-Protect switch A provided (When this switch is set to the [LOCK] position,
no further data writing, deletion or formatting is possible. The ability to write, delete and format data is restored when the switch is returned to its original position.) The data on the card may be damaged or lost due to electromagnetic waves, static electricity or breakdown of the camera or the card. We recommend storing important data on a PC etc. Do not format the card on your PC or other equipment. Format it on the camera only to ensure proper operation. (P63) Keep the Memory Card out of reach of children to prevent swallowing.
VQT3A48
29
Preparation
pictures and operating time can be performed in the [REMAINING DISP.] (P134) in the [CUSTOM] menu. A Number of recordable pictures B Available recording time
Number of recordable pictures [9999i] is displayed if there are more than 10000 pictures remaining.
Number of recordable pictures for more than 10000 can be checked in the LCD recording information display (P64). Aspect ratio [X], Quality [A]
Picture size
L (16M) M (8M) S (4M)
2 GB
220 410 680
4 GB
440 810 1350
16 GB
1830 3330 5550
64 GB
7260 13000 21490
2 GB
70 81 88
4 GB
135 160 170
16 GB
560 660 710
64 GB
2240 2600 2820
Available recording time (when recording motion pictures) [AVCHD] Recording quality setting
24H 24L FSH FH SH H
2 GB
10 min 00 s 13 min 00 s 13 min 00 s 17 min 00 s 13 min 00 s 17 min 00 s
4 GB
21 min 00 s 28 min 00 s 28 min 00 s 37 min 00 s 28 min 00 s 37 min 00 s
16 GB
1 h 32 min 2 h 4 min 2 h 4 min 2 h 43 min 2 h 4 min 2 h 43 min
64 GB
6 h 13 min 8 h 25 min 8 h 25 min 11 h 1 min 8 h 25 min 11 h 1 min
2 GB
7 min 20 s 18 min 30 s 19 min 10 s 53 min 20 s
4 GB
15 min 20 s 38 min 40 s 40 min 10 s 1 h 51 min
16 GB
1 h 6 min 2 h 46 min 2 h 52 min 7 h 58 min
64 GB
4 h 29 min 11 h 12 min 11 h 39 min 32 h 16 min
The number of recordable pictures and operating time will increase or decrease in proportion to Motion pictures can be recorded continuously for up to 29 minutes 59 seconds. Also, motion
picture recorded continuously in [MOTION JPEG] is up to 2 GB. (Example: [7m 20s] with [ Remaining time for continuous recording is displayed on the screen.
VQT3A48
the capacity of the card. (These vary depending on the recording conditions and the type of card.) ])
30
Preparation
Press [MENU/SET].
Press 2/1 to select the items (year, month, day, hour, minute, display sequence or time display format), and press 3/4 to set.
A: Time at the home area B: Time at the travel destination (P116) : Cancel without setting the clock.
: :
without the battery. (Leave the charged battery in the unit for 24 hours to charge the built-in battery.)
Note The clock is displayed when [DISPLAY] is pressed several times during recording. You can set the year from 2000 to 2099. If the clock is not set, the correct date cannot be printed when you stamp the date on the If the clock is set, the correct date can be printed even if the date is not displayed on the screen
of the camera. pictures with [TEXT STAMP] (P145) or order a photo studio to print the pictures.
VQT3A48
31
Basic
Mode switching
Basic
Basic Programme AE Mode (P35) The subjects are recorded using your own settings. Intelligent Auto Mode (P48) The subjects are recorded using settings automatically selected by the camera.
32
VQT3A48
Basic
Advanced Aperture-Priority AE Mode (P93) The shutter speed is automatically determined by the aperture value you set. Shutter-Priority AE Mode (P93) The aperture value is automatically determined by the shutter speed you set. Manual Exposure Mode (P94) The exposure is adjusted by the aperture value and the shutter speed which are manually adjusted. Custom Mode (P105) Use this mode to take pictures with previously registered settings. Creative Motion Picture Mode (P106) Use this mode to record motion pictures in the selected mode.
You cannot take still pictures.
Scene Mode (P99) This allows you to take pictures that match the scene being recorded. My Colour Mode (P103) Use this mode to check colouring effects, select a colour mode from among eight colour modes, and then take pictures. Advanced Scene Mode Portrait Mode (P97) Use this mode to take pictures of people. Scenery Mode (P98) Use this mode to take pictures of scenery. Close-up Mode (P98) Use this mode to take pictures of a close-by subject.
VQT3A48
33
Basic
AFS is an abbreviation of Auto Focus Single. Focus is set automatically when the shutter button is pressed halfway. Focus will be fixed while it is pressed halfway. AFC is an abbreviation of Auto Focus Continuous. This mode allows you to compose a picture more easily by continuously focusing on the movement of the subject while the shutter button is pressed halfway. When taking pictures of a moving subject, the camera predicts the movement of the subject and focuses on it. (motion prediction) It may take time to focus on the subject if you rotate the
MF
AFC AFS
AFC
zoom ring from Wide to Tele or suddenly change the subject from a distant one to a nearby one. Press the shutter button halfway again when it is difficult to focus on the subject. When the brightness is not enough, this will work the same as [AFS]. [AFC] will not operate with certain lenses. For details, refer to page 20. MF
Note Focus sound will not beep if the Focus Mode is set to [AFC]. Also, the AF area will not be The focus range is different depending on the lens used. When the 14 140 mm/F4.0 5.8 lens supplied in DMC-GH2H is used: 0.5 m (1.64 feet) to When the 14 42 mm/F3.5 5.6 lens supplied in DMC-GH2K is used: 0.3 m (0.99 feet) to
displayed if the AF Mode is set to [ ].
34
VQT3A48
Basic
Subjects and recording conditions which are difficult to focus Fast-moving subjects, extremely bright subjects or subjects without contrast When recording subjects through windows or near shiny objects When it is dark or when jitter occurs When the camera is too close to the subject or when taking a picture of both distant and near
subjects
].
will flash in red if the correct exposure is not achieved, except when set to flash.) You will not be able to take a picture until the focus is set, since the [FOCUS PRIORITY] (P131) is set initially to [ON].
AB
Press the shutter button fully (push it in further), and take the picture.
The access indication lights (P29) red when pictures are being recorded on the card. Note To change the setting while taking pictures, refer to Using the [REC] Mode Menu (P118) or Using the [CUSTOM] Menu (P130). The shutter speed is automatically set between about 15 seconds and 1/4000th of a second in
the following cases. When the [SENSITIVITY] is set to [ISO160]. When the aperture value is set to F4.0 (when the 14 140 mm/F4.0 5.8 lens supplied in DMC-GH2H is attached). When the aperture value is set to F3.5 (when the 14 42 mm/F3.5 5.6 lens supplied in DMC-GH2K is attached).
VQT3A48
35
Basic
Do not cover the flash or the AF assist lamp with Hold the camera gently with both hands, keep your
your fingers or other objects. arms still at your side and stand with your feet slightly apart. Be careful not to move the camera when you press the shutter button. When taking pictures, make sure your footing is stable and there is no danger of colliding with another person, an object etc. You cannot record 3D pictures in vertical orientation.
Direction Detection Function Pictures recorded with the camera held vertically are played back vertically (rotated). (Only when [ROTATE DISP.] (P149) is set to [ON]) The Direction Detection Function may not operate correctly if recording is performed with the You can only use the Direction Detection Function when using a compatible lens.
(Refer to the catalogue, website etc. for compatible lenses.) camera aimed up or down.
36
VQT3A48
Basic
Programme Shift In Programme AE Mode, you can change the preset aperture value and shutter speed without changing the exposure. This is called Programme Shift. You can make the background more blurred by decreasing the aperture value or record a moving subject more dynamically by slowing the shutter speed when taking a picture in Programme AE Mode.
1 2
Press the shutter button halfway and display the aperture value and shutter speed value on the screen. While the values are displayed (about 10 seconds), perform the Programme Shift by rotating the rear dial.
It will switch between Programme Shift operation and Exposure Compensation operation (P76) Rotate the rear dial to display the [EXPO.METER] B. (P133) The Programme Shift indication A appears on the screen when Programme Shift is activated. To cancel Programme Shift, turn the camera off or rotate the rear dial until the Programme Shift
indication disappears. every time the rear dial is pressed while the values are displayed.
Example of Programme Shift (When the 14 42 mm/F3.5 5.6 lens supplied in DMC-GH2K is used) (A): Aperture value (B): Shutter speed 1 Programme Shift amount 2 Programme Shift line chart 3 Programme Shift limit
1 2 2.8 4 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 (Ev) 15 16 17 18 19 20
(A) 5.6
8 11 16 22
1/2
1/4
1/8
1/15
1/30
(B)
Note EV is an abbreviation of [Exposure Value]. How the Exposure Compensation is switched can be changed by [EXPO. SETTINGS] (P133) If the exposure is not adequate when the shutter button is pressed halfway, the aperture value Programme Shift is cancelled and the camera returns to normal Programme AE Mode if more
than 10 seconds pass after Programme Shift is activated. However, the Programme Shift setting is memorised. Depending on the brightness of the subject, Programme Shift may not be activated. Programme Shift is not possible when the [SENSITIVITY] is set to [ ]. and shutter speed turn red and blink. in the [CUSTOM] menu.
VQT3A48
37
Basic
Touch [ ] in Recording Mode. Icon will change to [ ], and taking a picture with the
Touch Shutter function becomes possible.
Touch the subject you wish to focus on, and then take a picture.
A Rough indication of the area that can be focused with the Touch Shutter
displayed at the position you touch, and a picture is taken when it is focused. (It cannot be set to edge of the screen.) If the histogram is displayed on top of the subject you want to touch, touch the subject after first moving the histogram. (P66)
Touch [
Note If [FOCUS PRIORITY] is [ON], when the Focus Mode is set to [AFS] and the Touch Shutter
fails, AF area will disappear after turning red, and the picture will not be taken. When set to [AFC], the picture will not be taken if the focus indication is flashing green, but if the subject comes into focus while keeping touching the screen, the picture will be taken. Measurement of brightness is performed on the spot touched when the [METERING MODE] is set to []. (P122)
38
VQT3A48
Basic
To finish playback Press [(] again, press the motion picture button or press the shutter button halfway. Note This camera complies with the DCF standard Design rule for Camera File system established
by JEITA Japan Electronics and Information Technology Industries Association and with Exif Exchangeable Image File Format. Files which do not comply with the DCF standard cannot be played back.
VQT3A48
39
Basic
Changing the information displayed on the playback screen Press [DISPLAY] to switch the monitor screen.
A [DISPLAY] button
pictures (P46) and during a slide show (P141), you can only select Normal display B or No display F. Histogram D is displayed in R (red), G (green), B (blue), and Y (luminance) during the playback.
STD.
1/9
F3.5
0
WB ISO
30
AFS
AWB 160
P STANDARD
P F3.5 30
0
F3.5
1.DEC.2010 100-0001
0
30
ISO160
160
AWB
10:00 s
RGB
1/9
100-0001
B C D E F
Normal display Detailed information display Histogram display Highlight display No display This is displayed if [HIGHLIGHT] (P130) in the [CUSTOM] menu is set to [ON].
Rotate the rear dial right to return to the previous screen. If you select a picture with the Burst icon [], and press [MENU/SET], the pictures from within Screen can be switched by dragging the slide bar up or down (P16). The screen can be switched gradually by dragging the screen up or down (P16). Pictures are not rotated for display. Pictures displayed using [ ] cannot be played back. To return to Normal Playback Touch the picture to select. You can also return to the one screen display by choosing images pressing the cursor button,
and then pressing [MENU/SET] or the rear dial.
VQT3A48
that Burst Picture group will be played back using Multi Playback.
40
Basic
Press [MENU/SET] or the rear dial to display the pictures that were recorded on the selected date.
Rotate the rear dial left to return to the Calendar If you select a picture with the Burst icon [], and
screen display. press [MENU/SET], the pictures from within that Burst Picture group will be played back using Multi Playback.
or
Press 3/4/2/1 to select a picture and then press [MENU/SET] or the rear dial.
The picture that was selected will appear. Note The recording date of the picture selected in the playback screen becomes the date selected If there are multiple pictures with the same recording date, the first picture recorded on that day You can display the Calendar between January 2000 and December 2099. If the date is not set in the camera, the recording date is set as the 1st January, 2010. If you take pictures after setting the travel destination in [WORLD TIME], the pictures are
displayed by the dates at the travel destination in Calendar Playback. is displayed. when the Calendar screen is first displayed.
VQT3A48
41
Basic
Switching the displayed image while maintaining the Playback Zoom You can switch the displayed image while maintaining the same zoom magnification and zoom position for the Playback Zoom.
Switch to picture select operation by pressing the rear dial during Playback Zoom, and select pictures with 2/1.
It will switch between picture select operation and move
zoom position operation every time the rear dial is pressed during Playback Zoom.
Note You can also delete the recording information etc. on the screen during Playback Zoom by If you want to save the enlarged picture, use the Cropping function. (P148) The Playback Zoom may not operate if pictures have been recorded with other equipment. The zoom magnification and the zoom position are cancelled when the camera is turned off The zoom position returns to the centre in the following images. Images with different aspect ratios Images with different numbers of recorded pixels Images with a different rotation direction (when [ROTATE DISP.] is set to [ON]) Playback Zoom is not available during Motion Picture Playback.
(including Sleep Mode). pressing [DISPLAY].
42
VQT3A48
Basic
[REC] Mode:
The focus position is fixed when beginning to record a motion picture. It is possible to set the focus by
pressing the shutter button halfway or touching the subject.
MF
ON OFF
Depending on the recording conditions or lens used, operational sound may be recorded when
the Auto Focus is operated while recording a motion picture. It is recommended to record with [CONTINUOUS AF] in the [MOTION PICTURE] Mode menu set to [OFF], if the sound of operation bothers you to avoid recording the lens noise. When operating the zoom when recording motion pictures, it may take time to come into focus.
VQT3A48
43
Basic
C E
Sound will be heard when pressing the motion picture The recording state indicator (red) E will flash while
recording motion pictures.
44
VQT3A48
Basic
Motion pictures recorded in [AVCHD] or [MOTION JPEG] may be played back with poor
picture or sound quality or playback may not be possible even when played back with equipment compatible with these formats. Also, the recording information may not be displayed properly. In this case, use this unit. For details on AVCHD compatible devices, refer to the support site below.
http://panasonic.jp/support/global/cs/dsc/
(This Site is English only.) The sound recording specifications on this model have been changed to improve audio quality. For this reason, some motion pictures recorded in [MOTION JPEG] and pictures with audio may not be played back with Panasonic digital cameras (LUMIX). (Motion pictures recorded with a Panasonic digital camera (LUMIX) can be played back on this model.) Models launched before December 2008, and some models launched in 2009 (FS, LS series). To play back AVCHD motion pictures recorded with this unit on Panasonic Blu-ray Disc Players (DMP-BD30/DMP-BD31/DMP-BD50) it is necessary to update the firmware of the Blu-ray Disc Player. You can download the latest firmware version from the following website.
http://panasonic.net/support/
VQT3A48
45
Basic
Press [(]. Select a picture with a Motion Picture icon ([ [ ]) and then touch [ ] to play back.
A Motion picture icon B The motion picture recording time
],
the upper right of the screen. For example, 8 minutes and 30 seconds is displayed as [8m30s]. Some information (recording information, etc.) is not displayed for motion pictures recorded in [AVCHD]. Pressing the cursor button 3 to allows you to playback motion pictures. Display at the bottom right of the screen while playing back corresponds to 3/4/2/1 on the cursor button.
Operations performed during Motion Picture Playback 1 Display control panel by touching screen. If no operation is performed for 2 seconds, it will return to original status. 2 Operate control panel by touching.
C Fast rewind, Frame-by-frame rewind2 D Play/Pause 2 E Fast forward, Frame-by-frame forward F Stop G Reduce volume level1 H Increase volume level1 1 You can also adjust the volume level by using the rear dial. 2 These operations can be performed only in the Pause Mode and the following icons are displayed. Frame-by-frame rewind: [ ] Frame-by-frame forward: [ ] About fast forward/rewind playback Touch [ ] during playback to fast forward (touch [ ] to fast rewind). The fast forward/ rewind speed increases if you touch [ ]/[ ] again. (The display on the screen changes from [5] to [ ].) Touch [ ] to resume normal playback speed. When using a high capacity card, it is possible that fast rewinding may be slower than usual.
46
VQT3A48
Basic
Note Sound can be heard through the speaker. Refer to [VOLUME] (P58) for information about how To play back the motion pictures recorded by this unit on a PC, use the QuickTime or the QuickTime Motion JPEG motion pictures that were recorded with a PC or other equipment may
have lower image quality or may not be able to play back with this unit. PHOTOfunSTUDIO 6.0 BD Edition software on the CD-ROM (supplied). to adjust the volume in the [SETUP] menu.
VQT3A48
47
Basic
[REC] Mode:
Scene Detection When the camera identifies the optimum scene, the icon of the scene concerned is displayed in blue for 2 seconds, after which its colour changes to the usual red.
>
[i-PORTRAIT] [i-SCENERY]
[i-MACRO]
[i-NIGHT PORTRAIT] [i-NIGHT SCENERY] [i-SUNSET] [i-BABY] When recording motion pictures
Only when [
] is selected
>
[] is set if none of the scenes are applicable, and the standard settings are set. When [ ],[ ] or [ ] is selected, the camera automatically detects a persons face, and it will
adjust the focus and exposure. (Face Detection) (P82)
VQT3A48
48
Basic
If a tripod is used, for instance, and the camera has judged that camera shake is minimal when
the Scene Mode has been identified as [ ], the shutter speed will be slower than normal. Take care not to move the camera while taking pictures. An optimum scene for the specified subject will be chosen when set to AF tracking (P49). When [FACE RECOG.] is set to [ON], and the face similar to the registered face is detected, [R] is displayed in the top right of [ ], [ ] and [ ]. When [FACE RECOG.] is set to [ON], [ ] will be displayed for birthdays of registered faces already set only when the face of a person 3 years old or younger is detected.
Note Due to conditions such as the ones below, a different scene may be identified for the same
subject. Subject conditions: When the face is bright or dark, the size of the subject, the colour of the subject, the distance to the subject, the contrast of the subject, when the subject is moving Recording conditions: Sunset, sunrise, under low brightness conditions, when the camera is shaken, when zoom is used To take pictures in an intended scene, it is recommended that you take pictures in the appropriate Recording Mode. The Backlight Compensation Backlight refers to when light comes from the back of a subject. In this case, the subject will become dark, so this function compensates the backlight by brightening the whole of the picture automatically. Backlight compensation is automatically applied in Intelligent Auto Mode.
AF Tracking Function It is possible to set the focus and exposure to the specified subject. Focus and exposure will keep following the subject automatically even if it moves. When operating the touch panel You can lock the subject by touching it. [ ] is displayed in the lower left of the screen. AF Tracking frame will be displayed in yellow, and it
will determine the most appropriate scene for the locked subject. AF Tracking is cancelled when [CANCEL] is touched.
Press and hold [Q.MENU] button until AF Tracking frame is displayed. [ ] is displayed in the lower left of the screen. AF Tracking frame is displayed in the centre of the AF Tracking is cancelled when [MENU/SET] is
pressed. screen.
Place the subject in the Tracking frame, and press the shutter button halfway to lock the subject. AF area will turn green when the camera detects the subject. AF tracking frame will turn yellow when you release the shutter button and Press [MENU/SET] to cancel.
the optimum scene for the locked subject will be identified.
Note [FACE RECOG.] does not work during AF tracking. Use AF Tracking with the Touch Shutter function cancelled. Please read the Note regarding the AF tracking on P83.
VQT3A48
49
Basic
Settings in Intelligent Auto Mode [REC] Mode menu [ASPECT RATIO] (P120)/[PICTURE SIZE] (P120)/[QUALITY] (P121)/[FACE RECOG.] (P109)/[STABILIZER]1 (P75)
1 It cannot be set to [MODE3]. It will be fixed to [MODE1] when recording a motion picture even if it is set to [MODE2].
[MOTION PICTURE] Mode menu [REC MODE] (P127)/[REC QUALITY]2 (P127)/[CONTINUOUS AF] (P43)/[WIND CUT] (P129)
2 [ ] for [MOTION JPEG] cannot be set.
[CUSTOM] menu [CUST. SET MEM.] (P105)/[GUIDE LINE] (P130)/[LCD INFO.DISP.] (P134)/ [REMAINING DISP.] (P134) [SETUP] menu [CLOCK SET] (P31)/[WORLD TIME] (P116)/[BEEP] (P58)/[LCD MODE] (P59)/ [LANGUAGE] (P62) Use the Quick Menu (P56) to set the following functions: [STANDARD] and [STANDARD] ( ) in [FILM MODE] (P118) [ ] and [ ] in [SELF-TIMER]3 (P81)
3 It will be reset to [ ] when the Intelligent Auto Mode is cancelled or when the power is switched [ON]/[OFF].
50
VQT3A48
Basic
[ECONOMY] ([SLEEP MODE]) (P59) Flash (P69) [BURST RATE] (P77) [AUTO BRACKET] (P79)
[5MIN.] [ ]/[]
[FLASH SYNCHRO] (P123) [1ST] [H] (High speed) [ / SETTINGS]: [ ] (burst) [STEP]: [31/3] [SEQUENCE]: [0/`/_] AF Mode (P82) [WHITE BALANCE] (P88) [SENSITIVITY] (P91) [] (Set to [ [AWB] [ ]5 (Intelligent ISO) (The maximum ISO sensitivity: [ISO800]) ]4 when a face cannot be detected)
[METERING MODE] (P122) [C] [RED-EYE REMOVAL] (P70) [ON] [I.DYNAMIC] (P124) [LONG SHTR NR] (P124) [COLOR SPACE] (P126) [PICTURE MODE] (P108) [PRE AF] (P131) [STANDARD] [ON] [sRGB] [ [ ] ]
Flash Open the flash when the flash is to be used. (P69) Flash modes cannot be switched using the menu in the Intelligent Auto Mode. [ ], [ ], [ ] or [ ] is set depending on the type of subject and brightness. When [ ] or [ ] is displayed, the Digital red-eye correction is turned on. Shutter speed will be slow when using [ ] or [ ].
VQT3A48
51
Basic
Deleting Pictures
Once deleted, pictures cannot be recovered.
Press [(].
To delete a single picture
Press []. Press 3/4 to select [DELETE MULTI] or [DELETE ALL] and then press [MENU/SET]. [DELETE ALL] > step 5. Press 3/4/2/1 to select the picture, and then press [DISPLAY] to set. (Repeat this step.)
[] appears on the selected pictures. If [DISPLAY] is
pressed again, the setting is cancelled.
Press [MENU/SET]. Press 3 to select [YES] and then press [MENU/SET] to set.
52
VQT3A48
Basic
When [DELETE ALL] has been selected with the [FAVORITE] (P150) setting The selection screen is displayed again. Select [DELETE ALL] or [ALL DELETE EXCEPT], press 3 to select [YES] and delete the pictures. Note Do not turn the camera off while deleting (while [] is displayed). Use a battery with sufficient
battery power or the AC adaptor (DMW-AC8E; optional) and DC coupler (DMW-DCC8; optional). If you press [MENU/SET] while deleting pictures using [DELETE MULTI], [DELETE ALL] or [ALL DELETE EXCEPT ], the deleting will stop halfway. Depending on the number of pictures to be deleted, it may take some time to delete them. If pictures do not conform to the DCF standard or are protected (P152), they will not be deleted even if [DELETE ALL] or [ALL DELETE EXCEPT] is selected.
VQT3A48
53
Basic
set the aspect ratio, number of pixels and other aspects of the pictures you are recording.
perform the clock settings, select the operating beep tone settings and set other settings which make it easier for you to operate the camera. [MY MENU]
set the [REC MODE], [REC QUALITY], and other aspects for motion picture recording. [CUSTOM] menu (P130 to 136)
Up to 5 menu items
used recently can be memorised. Items used a lot can be recalled easily.
such as displaying of the screen and button operations, can be set up according to your preferences. Also, it is possible to register the modified settings.
Note There are functions that cannot be set or used depending on the modes or menu settings being
used on the camera due to the specifications.
54
VQT3A48
Basic
].
Press 4 or rotate the rear dial to select the [SETUP] menu icon [
]. or
Press 1 or the rear dial. Select a menu item next and set it. or
VQT3A48
55
Basic
or
or
When operating the touch panel Setting of the Quick Menu can be set using the touch panel.
56
VQT3A48
Basic
Touch [
When operating buttons The Quick Menu can be set by pressing the [Q.MENU] button. To close the Quick Menu, press [Q.MENU] button again. Setup method is different depending on the displayed screen during recording.
Refer to P64 about the displayed screen.
[ ] (LCD monitor style) After selecting the items with 2/1, you can select the setting contents with 3/4. Set by pressing [MENU/SET].
LCD recording information display in [ ] (LCD monitor style) Select the item with 3/4/2/1, press [MENU/SET], and then select the setting contents with 3/4/2/1. Set by pressing [MENU/SET]. You can also use the rear dial to set. You can change the settings by directly touching the items,
without displaying the Quick Menu.
[ ] (Finder style) Select the item by rotating the rear dial, and then press the rear dial. Select the setting contents by rotating the rear dial, and then press the rear dial to set. You can also press 2/1 and [MENU/SET] to set.
VQT3A48
57
Basic
[DESTINATION]/ [HOME]
[TRAVEL SETUP]/[LOCATION]
Refer to P115 for details. Set the volume for electronic noises and the electronic shutter noise.
[BEEP]
[ [ [
The [E-SHUTTER VOL] only works when set to [SH] for Burst Mode.
u [VOLUME]
When you connect the camera to a TV, the volume of the TV speakers does not change.
[MONITOR]/ [VIEWFINDER]
Brightness, colour, or red or blue tint of the LCD monitor/ viewfinder is adjusted.
Adjust the brightness of the screen with 3/4, contrast and saturation When [DISPLAY] is pressed in screen shown right, it will switch to the
with 2/1 or the rear dial. colour adjustment screen. Adjust between green and red with 3/4, or between orange and blue with 2/1 or the rear dial. Press [MENU/SET] to return to the LCD adjustment screen. It will adjust the LCD monitor when the LCD monitor is in use, and the viewfinder when the viewfinder is in use. Some subjects may appear differently from actuality on the LCD monitor/viewfinder. However, this does not affect the recorded pictures.
58
VQT3A48
Basic
The brightness of the LCD monitor can be adjusted depending on how bright it is around the camera. [AUTO]: The brightness is adjusted automatically depending on how bright it is around the camera. [MODE1]: 1 Make the LCD monitor brighter. [MODE2]: 2 Set the LCD monitor to the standard brightness. [MODE3]: 3 Make the LCD monitor darker.
The brightness of the pictures displayed on the LCD monitor is increased so some subjects
may appear differently from actuality on the LCD monitor. However, this does not affect the recorded pictures. The LCD monitor automatically returns to standard brightness after 30 seconds when recording in [MODE1]. Press any button to make the LCD monitor bright again. If the screen is difficult to see because of light from the sun etc. shining on it, use your hand or another object to block the light. The number of recordable pictures decreases in [AUTO] and [MODE1]. [AUTO] cannot be selected when playing back pictures. [AUTO] is disabled during motion picture recording. When the menu screen is displayed in a dark environment etc., the LCD monitor becomes darker even if [LCD MODE] is set to [MODE2]. The initial setting when using the AC adaptor (DMW-AC8E; optional) is [MODE2].
You can conserve the battery life by setting these menus. Also, it will turn off the LCD monitor automatically when not in use to prevent discharge of the battery.
p [SLEEP MODE]: The camera is automatically turned off if the camera has not been used for the time selected on the setting. [OFF]/[1MIN.]/[2MIN.]/[5MIN.]/[10MIN.]
q [ECONOMY]
[AUTO LCD OFF]: The LCD monitor is automatically turned off if the camera has not been used for the time selected on the setting. [OFF]/[15SEC.]/[30SEC.] Press the shutter button halfway or turn the camera off and on to cancel [SLEEP MODE]. [SLEEP MODE] is set to [5MIN.] in the Intelligent Auto Mode. [SLEEP MODE] is fixed to [2MIN.] when [AUTO LCD OFF] is set to [15SEC.] or [30SEC.]. Press any button to turn on the LCD monitor again. Since [ECONOMY] is cancelled when the eye sensor auto switching is performed, it is [SLEEP MODE] does not work in the following cases. When using the AC adaptor When connecting to a PC or a printer When recording or playing back motion pictures During a slide show
recommended to use this mode with [AUTO SWITCH] in [LVF/LCD SWITCH] (P134) set to [OFF].
VQT3A48
59
Basic
Set the length of time that the picture is displayed after taking it.
o [AUTO REVIEW]
[OFF]/[1SEC.]/[3SEC.]/[5SEC.] [HOLD]: The pictures are displayed until shutter button is pressed halfway.
] (P35) or [ ] (P81), switching of the playback screen display (P40) or enlargement by rotating the rear dial is possible during Auto Review. Regardless of the Auto Review setting, pictures will automatically be reviewed when taking burst pictures with [SH] or [H] set (P77), and recording with Auto Bracket (P79) or with [ASPECT BRACKET] (P125). (Will not hold) Also, you cannot set the Auto Review function. If [HIGHLIGHT] (P130) is set to [ON], white saturated areas appear blinking in black and white when the Auto Review function is activated. When [AUTO REGISTRATION] in [FACE RECOG.] (P109) is set to [ON], [AUTO REVIEW] can only be set to [3SEC.] or [5SEC.].
Select the USB communication system after or before connecting the camera to your PC or your printer with the USB connection cable (supplied).
x [USB MODE]
y [SELECT ON CONNECTION]: Select either [PC] or [PictBridge(PTP)] if you connected the camera to a PC or a printer supporting PictBridge. { [PictBridge(PTP)]: Set after or before connecting to a printer supporting PictBridge. z [PC]: Set after or before connecting to a PC.
When [PC] is selected, the camera is connected via the USB Mass Storage communication When [PictBridge(PTP)] is selected, the camera is connected via the PTP (Picture Transfer
Protocol) communication system. system.
[NTSC]: [PAL]:
Video output is set to NTSC system. Video output is set to PAL system.
This will operate when the AV cable or HDMI mini cable (optional) is connected. Set to match the type of TV.
[TV ASPECT]
[W]: [X]:
When connecting to a 16:9 screen TV. When connecting to a 4:3 screen TV.
60
VQT3A48
Basic
Set the format for the HDMI output when playing back on the HDMI compatible high-definition TV connected with this unit using the HDMI mini cable (optional). [AUTO]: The output resolution is automatically set based on the information from the connected TV. [1080i]: The interlace method with 1080 available scan lines is used for output. [720p]: The progressive method with 720 available scan lines is used for output. [576p]1/[480p]2: The progressive method with 5761/4802 available scan lines is used for output.
[HDMI MODE]
1 When [VIDEO OUT] is set to [PAL] 2 When [VIDEO OUT] is set to [NTSC]
If the images are not output on the TV when the setting is [AUTO], match with the image format
your TV can display, and select the number of effective scanning lines. (Please read the operating instructions for the TV.) This will work when the HDMI mini cable (optional) is connected. Refer to P158 for details.
Setup so this unit can be controlled by the remote control of the VIERA equipment by automatically coupling this unit with the VIERA Link compatible equipment using HDMI mini cable (optional).
[VIERA Link]
[OFF]: [ON]:
Operation is performed with the buttons on this unit. Remote control operation of the VIERA Link compatible equipment is enabled. (Not all operations are possible) Button operation of the main unit will be limited.
This will work when the HDMI mini cable (optional) is connected. Refer to P159 for details. Setup the output method for 3D pictures. [
[3D PLAYBACK]
]: ]:
Set when connecting to a 3D compatible television. Set when connecting to a television not compatible with 3D. Set this when you would like to view pictures in 2D (conventional image) on a 3D compatible television.
This will work when the HDMI mini cable (optional) is connected. Refer to P155 for the method to playback 3D pictures in 3D.
VQT3A48
61
Basic
[FAVORITE FUNC.]
during playback. You can also set favourites from the playback menu. For details, refer to P150.
Set the screen that is displayed when the mode dial is set to , , and . [OFF]:
[MENU GUIDE]
The recording screen in the currently selected Advanced Scene Mode (P97), Scene Mode (P99) or Creative Motion Picture Mode (P106) appears. The Advanced Scene Mode, Scene Mode or Creative Motion Picture Mode menu screen appears.
[AUTO]:
Adjust the position of the touch panel if a different thing gets selected from what you touched or touch operation does not respond.
[CALIBRATION]
1 2
Press [MENU/SET]. Touch the orange [r] mark displayed on the screen in order with the stylus pen (supplied) (5 places). A message is displayed once the Press [MENU/SET] to finish.
position is set.
Calibration is not done if correct position is not touched. Touch the [i] mark again. Set the language displayed on the screen.
~ [LANGUAGE]
[ENGLISH]/[DEUTSCH]/[FRANAIS]/[ESPAOL]/[ITALIANO]/ []
If you set a different language by mistake, select [~] from the menu icons to set the desired
language.
[VERSION DISP.]
This enables the firmware versions of the camera and lens to be checked.
62
VQT3A48
Basic
v [NO.RESET]
The folder number is updated and the file number starts from 0001. (P166) A folder number between 100 and 999 can be assigned.
When the folder number reaches 999, the number cannot be reset. We recommend formatting the card (P63) after saving the data on a PC or elsewhere. To reset the folder number to 100, format the card first and then use this function to reset the file number. A reset screen for the folder number will then appear. Select [YES] to reset the folder number. w [RESET] reset.
The [REC] or [SETUP]/[CUSTOM] menu settings are reset to the initial settings.
When the [REC] Mode settings are reset, data registered with [FACE RECOG.] will also be When [SETUP]/[CUSTOM] menu settings are reset, the following settings are also reset. In
addition, [ROTATE DISP.] (P149) in [PLAYBACK] Mode menu is set to [ON]. The birthday and name settings for [BABY1]/[BABY2] (P101) and [PET] (P102) in Scene Mode. The settings of [TRAVEL DATE] (P115) (departure date, return date, location) The [WORLD TIME] (P116) setting. The folder number and the clock setting are not changed.
[FORMAT]
The card is formatted. Formatting permanently deletes all data on your memory card. Please be sure all pictures and motion pictures are saved elsewhere before using this feature.
Use a battery with sufficient battery power or the AC adaptor (DMW-AC8E; optional) and DC
If the card has been formatted on a PC or other equipment, format it on the camera again. If the card cannot be formatted, please try another card before contacting your nearest Service
Centre.
coupler (DMW-DCC8; optional) when formatting. Do not turn the camera off during formatting.
VQT3A48
63
Recording
Recording
(LCD monitor display) ] (LCD monitor style). Screens here are an example of when it is set to [ With the [LCD DISP.STYLE] of the [CUSTOM] menu, you can choose the displayed screen on the LCD monitor to display in [ ] (LCD monitor style) or [ ] (viewfinder style).
STD.
P
AWB
9
AUTO
ISO AF
WB
1 2 3 4
1 2
0
5 5
3 4
AFS
AU TO AWB
STD.
B C D E
[LCD INFO.DISP.]3
(Viewfinder display) ] (viewfinder style). Screens here are an example of when it is set to [ With the [LVF DISP.STYLE] of the [CUSTOM] menu, you can choose the displayed screen on the viewfinder to display in [ ] (viewfinder style) or [ ] (LCD monitor style).
F Normal displayidetailed information1, 2 G Normal display1
STD.
AFS
AU TO
AWB 9
AFS
AU TO
AWB 9
64
VQT3A48
Recording
1 Guide lines are displayed when the [GUIDE LINE] of the [CUSTOM] menu is set to anything except [OFF]. 2 Histograms are displayed when the [HISTOGRAM] of the [CUSTOM] menu is set to [ON]. It is also possible to display the Exposure meter by setting the [EXPO.METER] of the [CUSTOM] menu to [ON]. (P133) 3 It is displayed when the [LCD INFO.DISP.] of the [CUSTOM] menu is set to anything except [OFF]. (P134)
Recording guide line When you align the subject on the horizontal and vertical guide lines or the cross point of these lines, you can take pictures with well-designed composition by viewing the size, the slope and the balance of the subject.
A [ B [ C [ ]: ]: ]: This is used when dividing the entire screen into 3k3 for taking pictures with a well-balanced composition. This is used when you want to position the subject at the exact centre of the screen. Position of the guide line can be set. It is used to take well balanced pictures of subjects off the centre of the image.
Set the position of the guide line with [ ] Set the [GUIDE LINE] in the [CUSTOM] menu to [ ]. Touch [ ] above the guide line, and drag it to the position you want to move it to (P16). You can also set the position of the guide line with the cursor button
in the Quick Menu (P57) while in button operation or [CUSTOM] menu. When it is difficult to move the guide line on the screen edge by touch operation, use the cursor button to set the position.
VQT3A48
65
Recording
About the Histogram A histogram is a graph that displays brightness along the horizontal axis (black to white) and the number of pixels at each brightness level on the vertical axis. It allows you to easily check a pictures exposure. Examples of histogram 1 Properly Exposed 2 Under Exposed 3 Overexposed
Histogram
STD.
STD.
STD.
AFS
P 3.5 100
AU TO AWB
AFS
P 3.5 200
AU TO
AWB
AFS
P 3.5 50
AU TO AWB
Set the position of the histogram Set the [HISTOGRAM] in the [CUSTOM] menu to [ON]. Touch the histogram and drag it to the position you want to move it to (P16). You can also set the position of the histogram with the cursor button
in the Quick Menu (P57) while in button operation or [CUSTOM] menu.
Note When the recorded picture and the histogram do not match each other under the
following conditions, the histogram is displayed in orange. When the manual exposure assistance is other than [n0] during Exposure Compensation or in the Manual Exposure Mode When the flash is activated When the flash is closed When the brightness of the screen is not correctly displayed in dark places When the exposure is not adequately adjusted The histogram is an approximation in the Recording Mode. The histogram displayed in this camera does not match histograms displayed by picture editing software used in PCs etc.
66
VQT3A48
Recording
[REC] Mode:
When the 14 140 mm/F4.0 5.8 lens supplied in DMC-GH2H is used 10k Recording magnification
When the 14 42 mm/F3.5 5.6 lens supplied in DMC-GH2K is used [2k] [4k] The higher the magnification level, the greater the deterioration. 3k
Picture quality
No deterioration
1 When a picture size of [S] (4 M), aspect ratio of [X] is selected. The magnification level differs depending on [PICTURE SIZE] and [ASPECT RATIO] setting. 2 When recording quality setting [ ] or [ ] is selected. When Recording Mode [AVCHD(1080i)] is selected, Extra Tele Conversion factor will change to 2.6. When Recording Mode [AVCHD(720p)] is selected, or Recording Mode [MOTION JPEG] is selected with recording quality setting [ ] or [ ], Extra Tele Conversion factor will change to 3.9.
Example: When the 14 42 mm/F3.5 5.6 lens supplied with the DMC-GH2K is used, you can achieve 24k magnification by 3k Optical Zoom i 2k Extra Tele Conversion i 4k Digital Zoom.
VQT3A48
67
Recording
Note With the Extra Tele Conversion, for example, when it is set to [
] (equal to 4 million pixels), it will take the picture using the 4 million pixels in the centre out of the 16 million pixels of the imaging device, resulting to be more of a telephoto picture. When the Extra Tele Conversion is used, angle of view for still pictures will be different from the angle of view for motion pictures because the zoom factor is different between them. Angle of view for recording can be checked beforehand by matching the [ REC AREA] (P134) setting to the mode you wish to record in. If you use the zoom function after focusing on the subject, focus on the subject again. When using the Digital Zoom, [STABILIZER] may not be effective. If camera shake (jitter) is a problem during Digital Zooming, it is recommended that [STABILIZER] be set to [MODE1]. When using the Digital Zoom, we recommend using a tripod and the self-timer (P81) for taking pictures. The AF Mode is fixed to [] when using the Digital Zoom. The Extra Tele Conversion and Digital zoom cannot be used in the following cases. When [QUALITY] is set to [ ], [ ] or [ ]
68
VQT3A48
Recording
[REC] Mode:
Press the flash until it clicks. Be sure to close the flash when not in use. The flash setting is fixed to [] while the flash is
closed.
1 2
Select [FLASH] in the [REC] Mode menu. (P55) Press 3/4 to select a mode and press [MENU/SET]. For information about flash settings that can be selected, refer to Available flash settings by Recording Mode. (P71)
VQT3A48
69
Recording
Description of settings The flash is automatically activated when the recording conditions make : AUTO it necessary. The flash is automatically activated when the recording conditions make it necessary. It is activated once before the actual recording to reduce the red-eye : phenomenon (eyes of the subject appearing red in the picture) and then AUTO/Red-Eye activated again for the actual recording. Reduction Use this when you take pictures of people in low lighting conditions. The flash is activated every time regardless of the recording conditions. : Forced Flash ON Use this when your subject is back-lit or under fluorescent light. The flash is activated every time regardless of the recording conditions. : Forced ON/Red-Eye Simultaneously it reduces the red-eye phenomenon. Reduction Use this when your subject is back-lit or under fluorescent light.
Item
: Slow Sync.
When taking pictures against a dark background landscape, this feature will slow the shutter speed when the flash is activated. Dark background landscape will appear brighter. Use this when you take pictures of people in front of a dark Using a slower speed can cause motion blur. Using a tripod can
background. enhance your photos. When taking pictures against a dark background landscape, this feature will slow the shutter speed when the flash is activated. Dark background landscape will appear brighter.
Simultaneously it reduces the red-eye phenomenon. Use this when you take pictures of people in front of a dark
background.
Using a slower speed can cause motion blur. Using a tripod can
enhance your photos. The flash is not activated in any recording conditions. Use this when you take pictures in places where the use of the flash is not permitted. Close the flash to turn it off when the built-in flash is used.
The flash is activated twice. The interval between the first and second flash is longer when [ ], [ ] or [ ] is set. The subject should not move until the second flash is activated.
[RED-EYE REMOVAL] on the [REC] Mode menu is set to [ON], [ flash icon. ] appears on the
About the Digital Red-Eye Correction When [RED-EYE REMOVAL] on the [REC] Mode menu has been set to [ON] and Red-Eye Reduction ([ ], [ ], [ ]) is selected, Digital Red-Eye Correction is performed whenever the flash is used. The camera automatically detects red-eye and corrects the picture. (Only available when the AF Mode is set to [] and Face Detection is active) Under certain circumstances, red-eye cannot be corrected.
70
VQT3A48
Recording
Available flash settings by Recording Mode The available flash settings depend on the Recording Mode. (: Available, : Not available, : Initial setting of Advanced Scene Mode and Scene Mode)
* +
. / 2 : ;
[ ] is displayed. [ ], [ ], [ ] or [ ] is set depending on the type of subject and brightness. The flash setting may change if the Recording Mode is changed. Set the flash setting again if necessary. The flash setting is memorised even if the camera is turned off. However, the Advanced Scene Mode or the Scene Mode flash setting is reset to the initial setting when the Advanced Scene Mode or the Scene Mode is changed. Flash will not be activated when recording motion picture.
VQT3A48
71
Recording
The available flash range to take pictures The available flash range is an approximation.
When the 14 140 mm/F4.0 5.8 lens supplied in DMC-GH2H is used ISO sensitivity Available flash range according to focal length of lens (When the aspect ratio is [X] or [ ].) Wide to 21 mm AUTO ISO160 ISO200 ISO400 ISO800 ISO1600 ISO3200 ISO6400 ISO12800 22 mm 1.0 m (3.28 feet) to 4.8 m (15.7 feet) 1.0 m (3.28 feet) to 3.0 m (9.84 feet) 1.0 m (3.28 feet) to 3.4 m (11.2 feet) 1.0 m (3.28 feet) to 4.8 m (15.7 feet) Vignetting effect occurs 1.0 m (3.28 feet) to due to the light of the 6.9 m (22.6 feet) flash. 1.0 m (3.28 feet) to 9.7 m (31.8 feet) 1.0 m (3.28 feet) to 13.8 m (45.3 feet) 1.2 m (3.94 feet) to 14.5 m (47.6 feet) 1.7 m (5.58 feet) to 27.6 m (90.6 feet) Tele 50 cm (1.64 feet) to 3.7 m (12.1 feet) 50 cm (1.64 feet) to 2.3 m (7.55 feet) 50 cm (1.64 feet) to 2.6 m (8.53 feet) 50 cm (1.64 feet) to 3.7 m (12.1 feet) 50 cm (1.64 feet) to 5.3 m (17.4 feet) 50 cm (1.64 feet) to 7.5 m (24.6 feet) 60 cm (1.97 feet) to 10.7 m (35.1 feet) 90 cm (2.95 feet) to 15.1 m (49.5 feet) 1.3 m (4.27 feet) to 21.4 m (70.2 feet)
When the 14 42 mm/F3.5 5.6 lens supplied in DMC-GH2K is used ISO sensitivity Wide AUTO ISO160 ISO200 ISO400 ISO800 ISO1600 ISO3200 ISO6400 ISO12800 45 cm (1.48 feet) to 6.2 m (20.3 feet) Available flash range Tele 30 cm (0.99 feet) to 3.9 m (12.8 feet)
45 cm (1.48 feet) to 3.9 m (12.8 feet) 30 cm (0.99 feet) to 2.4 m (7.87 feet) 45 cm (1.48 feet) to 4.4 m (14.4 feet) 30 cm (0.99 feet) to 2.7 m (8.85 feet) 45 cm (1.48 feet) to 6.2 m (20.3 feet) 30 cm (0.99 feet) to 3.9 m (12.8 feet) 50 cm (1.64 feet) to 8.8 m (28.9 feet) 30 cm (0.99 feet) to 5.5 m (18.0 feet) 80 cm (2.62 feet) to 12.5 m (41.0 feet) 1.1 m (3.61 feet) to 17.7 m (58.1 feet) 1.6 m (5.25 feet) to 25.1 m (82.3 feet) 2.2 m (7.22 feet) to 35.5 m (116.5 feet) 50 cm (1.64 feet) to 7.8 m (25.6 feet) 70 cm (2.29 feet) to 11.1 m (36.4 feet) 1.0 m (3.28 feet) to 15.7 m (51.5 feet) 1.4 m (4.59 feet) to 22.2 m (72.8 feet)
72
VQT3A48
Recording
At the time of flash photography, when distance with the subject is near, the flash light is
interrupted with the lens and a part of the picture being taken becomes dark. Check the distance between the camera and the subject when taking a picture. The distance from which the subject blocks the flash light differs according to the lens used. When the 14 140 mm/F4.0 5.8 lens supplied in DMC-GH2H is attached: When the aspect ratio is [X] or [ ]. Vignetting effect occurs due to the light of the flash. (Wide to 21 mm)/ 1.0 m (3.28 feet) or less (22 mm)/50 cm (1.64 feet) or less (Tele) When the aspect ratio is [Y]. Vignetting effect occurs due to the light of the flash. (Wide to 17 mm)/ 1.0 m (3.28 feet) or less (18 mm)/50 cm (1.64 feet) or less (Tele) When the aspect ratio is [W]. 2.5 m (8.20 feet) or less (Wide)/1.0 m (3.28 feet) or less (15 mm)/50 cm (1.64 feet) or less (Tele) When the 14 42 mm/F3.5 5.6 lens supplied in DMC-GH2K is attached: 45 cm (1.48 feet) or less (Wide)/30 cm (0.99 feet) or less (Tele)
1 This becomes 60 seconds in Shutter-Priority AE Mode. 2 This becomes 60 seconds in Shutter-Priority AE Mode and B (Bulb) in the Manual Exposure Mode. 3 This becomes B (Bulb) in the Manual Exposure Mode. When the flash is activated, the shutter speed cannot be set to faster than 1/160th of a second. In Intelligent Auto Mode, shutter speed changes depending on the identified scene.
Note Do not bring the flash too close to objects or close the flash while it is activated. The Do not close the flash soon after the flash is activated prior to taking pictures due to AUTO/ When you take a picture beyond the available flash range, the exposure may not be adjusted When the flash is being charged, the flash icon blinks red, and you cannot take a picture even When you take a picture beyond the available flash range, the White Balance may not be When you use certain lenses, light from the flash may be blocked or fail to cover the lens When taking pictures with flash with the lens hood attached, the lower portion of the photo may
turn dark (vignetting effect) and the control of the flash may be disabled because the photo flash may be obscured by the lens hood. We recommend detaching the lens hood. It may take time to charge the flash if you repeat taking a picture. Take a picture after the access indication disappears. The Red-Eye Reduction effect differs between people. Also, if the subject was far away from the camera or was not looking at the first flash, the effect may not be evident. When you attach an external flash, it takes priority over the built-in flash. Refer to P171 for the external flash. field of view, causing dark areas to appear in the resulting pictures. properly adjusted. when you press the shutter button fully. properly and the picture may become bright or dark. Red-Eye Reduction etc. It causes a malfunction. objects may be discoloured by its heat or lighting.
VQT3A48
73
Recording
1 2
Select [FLASH ADJUST.] in the [REC] Mode menu. (P55) Press 2/1 to set the flash output and then press [MENU/SET]. You can adjust from [j2 EV] to [i2 EV] in steps of [1/3 EV]. Select [0 EV] to return to the original flash output.
Note [i] or [j] is displayed on the flash icon in the screen when the flash
level is adjusted.
[REC] Mode:
When using a lens with an [O.I.S.] switch, it is possible to set to enable the Optical Image Stabilizer by switching the [O.I.S.] switch on the lens to [ON]. (It is set to [MODE1] at the time of purchase.)
74
VQT3A48
Recording
Setting the Stabilizer in the [REC] Mode menu 1 Select [STABILIZER] in the [REC] Mode menu. (P55) 2 Press 3/4 to select the setting and then press [MENU/SET]. [OFF]: [STABILIZER] does not work. (This can be selected only when using a lens without the [O.I.S.] switch.) Jitter is always compensated during [REC] Mode. The jitter is compensated for when the shutter button is pressed. Camera shake is corrected for up/down movements. This mode is ideal for panning (a method of taking pictures which involves turning the camera to track the movements of a subject which continues to move in a fixed direction).
When recording a motion picture, [STABILIZER] will be fixed to [MODE1] even if it is set to [STABILIZER] cannot be selected when a lens without Stabilizer function is used. Preventing jitter (camera shake) When the jitter alert [ ] appears, use [STABILIZER], a tripod, the self-timer (P81) or the remote shutter (DMW-RSL1; optional) (P172). Shutter speed will be slower particularly in the following cases. Keep the camera still from the
moment the shutter button is pressed until the picture appears on the screen. We recommend using a tripod. Slow Sync. Slow Sync./Red-Eye Reduction [NIGHT PORTRAIT], [NIGHT SCENERY] and [PARTY] in Scene Mode (P99) When you set to a slow shutter speed ] is [MODE2] or [MODE3].
Note It is recommended to disable the Optical Image Stabilizer when using a tripod. [
displayed on the screen at that time. The stabilizer function may not be effective in the following cases. When there is a lot of jitter. When the zoom magnification is high. When using the Digital Zoom. When taking pictures while following a moving subject. When the shutter speed becomes slower to take pictures indoors or in dark places. Be careful of camera jitter when you press the shutter button. The panning effect in [MODE3] is more difficult to achieve in the following cases. In brightly lit places such as in broad daylight on a summers day When the shutter speed is faster than 1/100th of a second. When you move the camera too slowly because the subject is moving slowly. (The background will not become a blur.) When the camera does not keep up with the subject satisfactorily We recommend taking pictures with the viewfinder when panning in [MODE3].
VQT3A48
75
Recording
[REC] Mode:
Press the rear dial to switch to Exposure Compensation operation. Rotate the rear dial to compensate the exposure.
A Exposure Compensation value B [EXPO.METER]
a range of j5 EV to i5 EV. When recording motion pictures, the Exposure Compensation value can be set within a range of j3 EV to i3 EV. Select [0] to return to the original exposure. Rotate the rear dial to display the [EXPO.METER]. (P133) (However, it does not appear in / // / / Mode.)
Note When the exposure value is out of the j3 EV to i3 EV range, the brightness of the recording
screen will no longer change. It is recommended to record by checking the actual brightness of the recorded image in the Auto Review or playback screen. The set exposure value is memorised even if the camera is turned off. However, the exposure value during the Intelligent Auto Mode is not memorised. The compensation range of the exposure will be limited depending on the brightness of the subject. When the aperture and shutter speed values are displayed in the screen in the Programme AE Mode, Programme Shift operation and Exposure Compensation operation is switched every time the rear dial is pressed. In the Aperture-Priority AE Mode, Aperture Setting operation (P93) and Exposure Compensation operation is switched every time the rear dial is pressed. In the Shutter-Priority AE Mode, Shutter Speed Setting operation (P93) and Exposure Compensation operation is switched every time the rear dial is pressed. Operation method can be changed with [EXPO. SETTINGS] in the [CUSTOM] menu. (P133) Exposure compensation can be performed by touching the exposure compensation display, and then using the slide bar in the Quick Menu (P56) while in touch operation. In the Quick Menu (P57) while in button operation, if set to [ ] (LCD monitor style), exposure compensation can be set with 3/4 after selecting to display exposure compensation with 2/1 or the rear dial.
VQT3A48
76
Recording
] (viewfinder style), after selecting the Exposure Compensation display using the rear dial or 2/1, pressing the rear dial or [MENU/SET] will allow you to compensate the exposure with the rear dial or 2/1.
[REC] Mode:
].
Changing the burst speed 1 Select [BURST RATE] in the [REC] Mode menu. (P55) 2 Press 3/4 to select the burst speed and then press [MENU/SET].
[SH] (Super high speed) Burst speed (pictures/second) Live View during Burst Mode 1 With RAW files Without RAW files 40 None Max. 40 [H] (High speed) 52 None [M] (Middle speed) 3 Available 4 to 73 Depends on the remaining capacity of the card3 [L] (Low speed) 2 Available
1 Number of recordable pictures 2 When quality is set to [ ], [ ] or [ ], burst speed is 4.5 pictures/second. 3 Pictures can be taken until the capacity of the card becomes full. However the burst speed will become slower halfway. The exact timing of this depends on the aspect ratio, the picture size, the setting for the quality and the type of card used.
VQT3A48
77
Recording
First burst speed has no relation with the transfer speed of the card. The burst speed values given above apply when the shutter speed is 1/60 or faster and when The Burst Mode speed may become slower depending on the following settings. [SENSITIVITY] (P91)/[PICTURE SIZE] (P120)/[QUALITY] (P121)/[FOCUS PRIORITY] The picture size will be fixed to [S] when [SH] is set. Refer to P121 for information about RAW files. Focusing in Burst Mode The focus changes depending on the setting for [FOCUS PRIORITY] (P131) in the [CUSTOM] menu and the Focus Mode setting. Focus Mode AFS AFC1 MF Focus Priority ON OFF ON OFF Focus At the first picture Normal focusing2 Predicted focusing3 Focus set with Manual Focus
(P131)/Focus Mode the flash is not activated.
1 When the subject is dark or the burst speed is set to [SH], the focus is fixed on the first picture. 2 The burst speed may become slower because the camera is continuously focusing on the subject. 3 Burst speed takes priority, and focus is estimated within possible range.
Note We recommend using the remote shutter (DMW-RSL1; optional) when you want to keep the
shutter button pressed fully while taking pictures in Burst Mode. Refer to P172 for information about the remote shutter. When the burst speed is set to [SH] or [H] (when the Focus Mode is [AFS] or [MF]), the exposure and White Balance are fixed at the settings used for the first picture for the subsequent pictures as well. Depending on the brightness of the subject, the second picture and subsequent pictures may be brighter or darker. When the burst speed is set to [H] (when the Focus Mode is [AFC]), [M] or [L], they are adjusted each time you take a picture. If you are following a moving subject while taking pictures in a place indoors, outdoors etc. where there is a large difference between the light and shade (landscape), it may take time until the exposure is stable. If burst is used at this time, the exposure may not become optimal. Since the shutter speed becomes slower in dark places, the burst speed (pictures/second) may become slower. When set to [SH] or [H], the Auto Review function is activated regardless of the Auto Review setting. (Will not hold) You cannot set the Auto Review function in the [SETUP] menu. When set to [M] or [L], Live View is displayed between burst frames. When the flash is activated, you can take only 1 picture. Maximum of 3 films will be recorded depending on the Multi Film Bracket setting during the Multi Film Bracket recording (P119). It will automatically switch to [H] when set to [SH]. The Burst Mode is disabled when White Balance Bracket or Aspect Bracket is set. The Burst Mode is disabled during recording of the motion pictures. The following functions cannot be used when the burst speed is set to [SH]. [EX. TELE CONV.]/[DIGITAL ZOOM]/[LONG SHTR NR]/[MODE2] of [STABILIZER]/[ ], [ ] or [ ] of [QUALITY]
78
VQT3A48
Recording
[REC] Mode:
d0 EV
j1/3 EV
i1/3 EV
].
If you press and hold the shutter button, the number The Auto Bracket indication blinks until the number of The picture count is reset to [0] if you change the
pictures that you set is taken. Auto Bracket setting, change the setting on the drive mode lever or turn the camera off before all the pictures that you set are taken. of pictures that you set is taken.
VQT3A48
79
Recording
1 2
Select [AUTO BRACKET] in the [REC] Mode menu. (P55) Press 3/4 to select [ / SETTINGS], [STEP] or [SEQUENCE] and then press 1.
Settings
] (single) ] (burst)
Item [SEQUENCE]
Settings
[0/`/_] [`/0/_]
[31/3] (3 pictures) [32/3] (3 pictures) [31] (3 pictures) [51/3] (5 pictures) [STEP] [52/3] (5 pictures) [51] (5 pictures) [71/3] (7 pictures) [72/3] (7 pictures) [71] (7 pictures)
You can take one picture at a time when set to [ ]. You can continuously take pictures up to set numbers when set to [
].
Note When taking pictures using Auto Bracket after setting the Exposure Compensation range, the The exposure may not be compensated with Auto Bracket depending on the brightness of the The Auto Review function is activated regardless of the Auto Review setting. (Will not hold) You When the flash is activated, you can take only 1 picture. Auto Bracket is disabled when Multi Film Bracket, White Balance Bracket, or Aspect Bracket is The Auto Bracket will be disabled during recording of the motion pictures.
set. cannot set the Auto Review function in the [SETUP] menu. subject. pictures taken are based on the selected Exposure Compensation range.
80
VQT3A48
Recording
[REC] Mode:
Press the shutter button halfway to focus and then press it fully to take the picture.
A When self-timer is set to [ ].
A picture is not taken until the subject is brought into focus. Focus and exposure will be set when the shutter button is pressed halfway. If you want to press the shutter button fully to take a
picture even when the subject is not focused, set [FOCUS PRIORITY] in the [CUSTOM] menu to [OFF]. (P131) The self-timer indicator B blinks and the shutter is activated after 10 seconds (or 2 seconds). If you press [MENU/SET] while taking a picture with the self-timer, it is cancelled. When [ ] is selected, the self-timer indicator blinks again after the first and the second pictures are taken and the shutter is activated 2 seconds after it blinks.
Changing the time setting for the self-timer 1 Select [SELF-TIMER] in the [REC] Mode menu. (P55) 2 Press 3/4 to select the mode and then press [MENU/SET].
Item Settings
10 seconds
After 10 seconds the camera takes 3 pictures at about 2 second intervals.
2 seconds Note When using a tripod etc., setting the self-timer to 2 seconds is a convenient way to avoid the We recommend using a tripod when recording with the self-timer. Depending on the recording conditions, the recording interval may become more than The flash output may not be constant when [ ] is set. Up to 3 films are recorded automatically, depending on the Multi Film Bracket setting, when the Use the Quick Menu (P56) to set when in Intelligent Auto Mode. It cannot be set to [ ] in Intelligent Auto Mode or when White Balance Bracket or Aspect The self-timer will be disabled during recording of the motion pictures.
VQT3A48
shutter button is pressed once during the recording with Multi Film Bracket. Bracket is set.
81
Recording
[REC] Mode:
Set the focus mode lever to [AFS] or [AFC]. Switching the auto focus mode dial.
MF
AFC AFS
Note It is not possible to set [] in the following cases. In [FOOD] in [CLOSE-UP] In [NIGHT SCENERY] in Scene Mode The AF Mode is fixed to [] when using the Digital Zoom. AF area will be fixed to a small point in [PERIPHERAL DEFOCUS] in Scene Mode. It will be set to [] when a recording is performed with the Touch Shutter function (P38). About [] (Face Detection) The camera automatically detects the persons face. The focus and exposure can then be adjusted to fit that face no matter what portion of the picture it is in. (max. 15 areas) When the camera detects a persons face, the AF area is displayed. Yellow: When the shutter button is pressed halfway, the frame turns green when the camera is focused. White: Displayed when more than one face is detected. Other faces that are the same distance away as faces within the yellow AF areas are also focused. Note Position and size of the AF area can be changed. (P84) When [] is selected and [METERING MODE] is set to multiple [C], the camera will adjust Under certain picture-taking conditions including the following cases, the facial recognition
the exposure to suit the persons face. (P122) function may fail to work, making it impossible to detect faces. The AF Mode is switched to [ ]. When the face is not facing the camera When the face is at an angle When the face is extremely bright or dark When there is little contrast on the faces When the facial features are hidden behind sunglasses, etc. When the face appears small on the screen When there is rapid movement When the subject is other than a human being When the camera is shaking The camera may detect the subjects other than a person as the face. In this case, switch the AF Mode to any modes other than [] and then take a picture.
82
VQT3A48
Recording
Setting up [
] (AF Tracking)
Focus and exposure can be adjusted to a specified subject. Focus and exposure will keep on following the subject even if it moves. (Dynamic tracking) When operating the touch panel You can lock the subject by touching it. The AF area turns yellow while the subject is locked. Lock is cancelled when [CANCEL] is touched.
When operating buttons Place the subject in the AF tracking frame, and press the shutter button halfway to lock the subject.
A AF tracking frame
AF area will turn green when the camera detects the subject. The AF area turns yellow when the shutter button is released. Lock is cancelled when [MENU/SET ] is pressed.
Note If it fails to lock, AF area will flash in red, and disappear. Try to lock again. AF Tracking will not operate when it has failed to AF track. AF Mode will be switched to [] in In the following cases, [ ] operates as [] When the Film Mode is [STANDARD] ( ), [DYNAMIC] ( ), [SMOOTH] ( When My Colour Mode is [MONOCHROME] When recording motion pictures Dynamic tracking function may not work in the following cases: When the subject is too small When the recording location is too dark or bright When the subject is moving too fast When the background has the same or similar colour to the subject When jitter is occurring When zoom is operated About [ ] (23-area-focusing)
that case. )
Up to 23 points for each AF area can be focused. This is effective when the subject is not in the centre of the screen. (AF area frame will be same as image aspect ratio setting) Note The 23 AF areas can be divided into 9 areas and the area to be focused can be set. (P84) AF area is not displayed until it is in focus. Also, when the Focus Mode is set to [AFC], the AF The camera is focusing on all the AF areas using [
area is not displayed even if it is in focus. ] when multiple AF areas (max. 23 areas) light at the same time. If you want to determine the focus position to take pictures, switch the AF Mode to [].
VQT3A48
83
Recording
About [] (1-area-focusing) The camera focuses on the subject in the AF area on the screen. Note Position and size of the AF area can be changed. (P84) When the subject is not in the centre of the composition in [], you can bring the subject into
the AF area, fix the focus and exposure by pressing the shutter button halfway, move the camera to the composition you want with the shutter button pressed halfway, and then take the picture. (Only when the focus mode lever is set to [AFS])
Setting up position of the AF area/changing size of the AF area When selecting [], [] Position and size of the AF area can be changed. 1 Touch the subject. AF area setting screen is displayed. It is also possible to move the AF area using the cursor
button after pressing and holding the [Q.MENU] button until the AF area setting screen is displayed. The AF area returns to the centre when [] is pressed.
Touch the slide bar to change the size of AF area frame. It can be changed to 4 different sizes. It is also possible to rotate the rear dial to the right to Touch [SET]. AF area with the same function as [] is displayed in
make it larger. Rotate it to the left to make it smaller.
the touched position, when the [] is selected. Setting of the AF area is cleared when [CANCEL] is touched.
When selecting [ ] The 23 AF areas can be divided into 9 areas and the area to be focused can be set. Touch the screen to display the AF area setting screen, and select the AF area frame as shown in the figure on the right. After releasing you finger from the touch panel for a while,
AF area frame will disappear, and only [i] display (centre point of selected AF area frame) will remain on the screen. Press and hold the [Q.MENU] button until the AF area setting screen is displayed. The AF area frame can then also be selected by pressing the cursor button or by rotating the rear dial. Setting of the AF area frame is cancelled when [CANCEL] is touched.
Move the AF area easily with button operations When the [DIRECT FOCUS AREA] in the [CUSTOM] menu is set to [ON] while [], [ or [] is selected, it is possible to move the AF area directly with the cursor button. Use the Quick Menu (P56) to set the functions assigned to the cursor button, such as
[SENSITIVITY] (P91), [WHITE BALANCE] (P88), etc.
Note The spot metering target can also be moved to match the AF area when using []. (P122) Change the size of the AF area when there is trouble focusing with a small AF area. [DIRECT FOCUS AREA] is fixed to [OFF] in My Colour Mode.
84
VQT3A48
Recording
[REC] Mode:
Set the focus mode lever to [MF]. Rotate the focus ring to focus on the subject.
When the [MF ASSIST] in the [CUSTOM] menu is set to [ON], MF guide B is displayed on the screen when the focus ring is
screen will be enlarged about 5 times as MF Assist. A rotated if the [MF GUIDE] in the [CUSTOM] menu is set to [ON]. You can check the direction of rotation of the focus ring is toward the near side or the far side.
MF ASSIST Displaying the MF Assist It is displayed by rotating the focus ring or touching the screen. It can also be displayed by pressing and holding the [Q.MENU] button to display the setup
screen for the enlarged area, deciding the area to enlarge using the cursor button, and then pressing [MENU/SET]. It will switch to the setting screen for the enlarged area by pressing the cursor button when the [DIRECT FOCUS AREA] in the [CUSTOM] menu is set to [ON].
Moving the enlarged area The enlarged area can be moved by dragging the screen (P16), or pressing the cursor The following will return the MF assistance to the original position. When the Focus Mode is set to other than [MF] Changing [ASPECT RATIO] or [PICTURE SIZE] Turning the camera off Changing the magnification It is enlarged to 10 times by touching [ ]. It will return to 5 times by touching [ ]. MF Assist is enlarged from 5 times to 10 times when the rear dial is rotated right. It will
return to 5 times by rotating the rear dial left. button.
Closing the MF Assist It will close when the shutter button is pressed halfway. It will also close by touching the [CANCEL] on the screen or pressing [MENU/SET]. When displayed by rotating the focus ring, it is closed approximately 10 seconds after the
operation is stopped.
Note The MF Assist does not appear when using the Digital Zoom or recording motion pictures. MF Assist or MF guide may not display depending on the lens used, but you can display MF
Assist by direct operation of the camera, using the touch panel or a button.
VQT3A48
85
Recording
Technique for Manual Focus 1 Rotate the focus ring to focus on the subject. 2 Rotate it a little more. 3 Finely focus on the subject by rotating the focus ring slowly in reverse. Note If you use the zoom function after focusing on the subject, focus on the subject again. After cancelling Sleep Mode, focus on the subject again. If you are taking close-up pictures We recommend using a tripod and the self-timer (P81). The effective focus range (depth of field) is significantly narrowed. Therefore, if the distance
between the camera and the subject is changed after focusing on the subject, it may become difficult to focus on it again. The resolution of the periphery of the picture may decrease slightly. This is not a malfunction.
About the focus distance reference mark The focus distance reference mark is a mark used Focus range to measure the focus distance. Use this when taking pictures with Manual Focus or taking close-up pictures.
A Focus distance reference mark B Focus distance reference line C 0.5 m (1.64 feet) (When the 14 140 mm/ F4.0 5.8 lens supplied in DMC-GH2H is used) D 0.3 m (0.99 feet) (When the 14 42 mm/ F3.5 5.6 lens supplied in DMC-GH2K is used)
86
VQT3A48
Recording
[REC] Mode:
Align the screen with the subject. Press and hold [AF/AE LOCK] to fix the focus or exposure.
A [AF/AE LOCK] button
While pressing [AF/AE LOCK], move the camera as you compose the picture and then press shutter button fully.
B AE lock indication
AF/AE Lock Locking of the focus and exposure can be set in [AF/AE LOCK] in the [CUSTOM] menu. [AE]: [AF]: Only the exposure is locked. [AEL], aperture value, the shutter speed light when the exposure is set. Only the focus is locked. [AFL], the focus indication, aperture value, the shutter speed light when the
subject is focused.
[AF/AE]:
Both focus and exposure are locked. [AFL], [AEL], the focus indication, aperture value and the shutter speed light
when the subject is focused and the exposure is set.
Note If you set [AF/AE LOCK HOLD] in the [CUSTOM] menu to [ON], you can fix the focus and the The brightness of the image displayed on the LCD monitor/viewfinder (Live View) will be also AF Lock only is effective when taking pictures in Manual Exposure Mode. AE Lock only is effective when taking pictures with Manual Focus. AE/AF lock cannot be performed again during motion picture recording. During motion picture The exposure is set, even if the brightness of the subject changes. The subject can be focused again by pressing the shutter button halfway even when AE is Programme Shift can be set even when AE is locked.
locked. recording only cancellation of AE/AF lock can be performed. locked when the AE lock is performed. exposure even if you release [AF/AE LOCK] after pressing it. (P131)
VQT3A48
87
Recording
[REC] Mode:
Press 1 (
).
[AWB] [V] [] [] [] [ [ [
1
Automatic adjustment When taking pictures outdoors under a clear sky When taking pictures outdoors under a cloudy sky When taking pictures outdoors in the shade When taking pictures under incandescent lights When taking pictures with the flash only
2
] ]/[ ] ]/[
3 2
]/[
When using the preset White Balance When using the preset colour temperature setting
Auto White Balance Depending on the conditions prevailing when pictures are taken, the pictures may take on a reddish or bluish tinge. Furthermore, when a multiple number of light sources are being used or there is nothing with a colour close to white, Auto White Balance may not function properly. In a case like this, set the White Balance to a mode other than [AWB]. 1 Auto White Balance will work within this range. 2 Blue sky 3 Cloudy sky (Rain) 4 Shade 5 Sunlight 6 White fluorescent light 7 Incandescent light bulb 8 Sunrise and sunset 9 Candlelight KlKelvin Colour Temperature
2) 3) 4) 1) 5) 6)
7) 8) 9)
88
VQT3A48
Recording
Note The optimal White Balance will differ depending on the type of fluorescent lighting being When the flash is used, if you take a picture beyond the available flash range, the White The White Balance is memorised even if the camera is turned off, but [WHITE BALANCE] for
the Advanced Scene Mode or the Scene Mode is set to [AWB] when the Advanced Scene Mode or the Scene Mode is changed. White Balance is fixed to [AWB] in following conditions. In Intelligent Auto Mode In [OUTDOOR PORTRAIT] and [INDOOR PORTRAIT] in [PORTRAIT] In [SCENERY] In [FOOD] in [CLOSE-UP] In [NIGHT PORTRAIT], [NIGHT SCENERY], [SUNSET] or [PARTY] in Scene Mode My Colour Mode When [DIRECT FOCUS AREA] (P84) is set to [ON], the operations on the cursor buttons translate to movements of the AF area. Set using the Quick Menu (P56). Balance may not be properly adjusted. recorded under so use [AWB], [
1
], [
], [
] or [
].
Setting the White Balance manually Set the White Balance value. Use to match the condition when taking photographs.
1 2 3
Select the white set icon (such as [ 1 ]), and then touch [SELECT WHITE SET]. The white set selecting screen can also be displayed by pressing the cursor button toward
3.
Select [ 1 ], [ 2 ], [ 3 ] or [ 4 ] and then touch [WHITE SET]. The White Balance setting screen can also be displayed by pressing the cursor button
toward 3.
Aim the camera at a sheet of white paper etc. so that the frame in the centre is filled by the white object only and then touch [SET].
Note White Balance may not be set when the subject is too bright or too dark. Set the White Balance
again after adjusting to appropriate brightness.
Setting the colour temperature You can set the colour temperature manually for taking natural pictures in different lighting conditions. The colour of light is measured as a number in degrees Kelvin. As the colour temperature increases, the picture becomes more bluish. As the colour temperature decreases, the picture becomes more reddish. 1 Select [ ] and then touch [WB K SET]. The colour temperature setting screen can also be
Touch the colour temperature setting bar. It is also possible to set the values by touching [3]/[4] or pressing 3/4 of the cursor button. You can set a colour temperature from [2500K] to Touch [SET].
VQT3A48
[10000K].
89
Recording
Finely adjusting the White Balance You can finely adjust the White Balance when you cannot acquire the desired hue by setting the White Balance.
1 2
Select the White Balance and then touch [ADJUST.]. The White Balance adjust screen can also be displayed by pressing the cursor button
toward 4.
Touch within the frame to finely adjust. You can finely adjust also by touching [G_]/[M`]/[A]/
[B], or pressing 3/4/2/1 of the cursor button.
2 1 3 4
: : : :
Touch [SET].
Note If you finely adjust the White Balance to A (amber), the White Balance icon on the screen will
change to orange. If you finely adjust the White Balance to B (blue), the White Balance icon on the screen will change to blue. If you finely adjust the White Balance to G_ (green) or M` (magenta), [_] (green) or [`] (magenta) appears beside the White Balance icon on the screen. Press [DISPLAY] to return to the centre point. Select the centre point if you are not finely adjusting the White Balance. The White Balance fine adjustment setting is reflected in the picture when using the flash. You can finely adjust the White Balance independently for each White Balance item. The White Balance fine adjustment setting is memorised even if the camera is turned off. The White Balance fine adjustment level returns to the standard setting (centre point) in the following cases. When you reset the White Balance in [ 1 ], [ 2 ], [ 3 ] or [ 4 ] When you reset the colour temperature manually in [ ]
White Balance Bracket Bracket setting is performed based on the adjustment values for the White Balance fine adjustment, and 3 pictures with different colours are automatically recorded when the shutter button is pressed once. 1 Finely adjust the White Balance in step 2 of the Finely adjusting the White Balance procedure, and touch [ ]/ [ ] to set the bracket. Bracket settings can also be made by rotating the rear dial.
[ [ ] or rear dial right: Horizontal (A to B) ] or rear dial left: Vertical (Gi to Mj)
Touch [SET].
Note [ ] is displayed in White Balance icon in the screen when the White Balance Bracket is set. The White Balance Bracket setting is released when the power has been turned off (including You will only hear the shutter sound once. [ ], [ ] or [ ] for [QUALITY] cannot be set. White Balance Bracket does not work when recording motion pictures.
Sleep Mode).
90
VQT3A48
Recording
[REC] Mode:
Press 3 (
).
Settings
The ISO sensitivity is automatically adjusted according to the brightness. The ISO sensitivity is adjusted according to the movement of the subject and the brightness.
(Intelligent)
160/200/250/320/400/500/640/ 800/1000/1250/1600/2000/2500/ The ISO sensitivity is fixed to various settings. 3200/4000/5000/6400/8000/ 10000/12800 When the [ISO LIMIT SET] of [REC] Mode menu (P124) is set to anything except [OFF], it is set automatically within the value set in [ISO LIMIT SET]. It is set as following when the [ISO LIMIT SET] is set to [OFF]. [When the 3D interchangeable lens (optional) is attached, it may become higher than the following settings.] When [AUTO] is selected, ISO sensitivity is adjusted automatically depending on brightness within a maximum setting of [ISO400]. When setting to [ ], ISO sensitivity will adjust automatically depending on brightness within the maximum setting of [ISO800]. ([ISO400] when the flash is used) The ISO sensitivity will be set to [AUTO] (for motion pictures) when recording motion pictures. Also, the [ISO LIMIT SET] will not operate. Setting items below will be selectable in Creative Motion Picture Mode. [AUTO]/[160] to [3200]
VQT3A48
91
Recording
About [ ] (Intelligent ISO sensitivity control) The camera automatically sets the optimum ISO sensitivity and shutter speed to suit the movement of the subject and brightness of the scene to minimise the jitter of the subject. The shutter speed is not fixed when the shutter button is pressed halfway. It is continuously
changing to match the movement of the subject until the shutter button is pressed fully. Confirm the actual shutter speed on the information display for the picture being played back.
Note The higher the value set for the ISO sensitivity, the more the jitter is reduced but the greater the Refer to P72 for the flash range. Depending on the brightness and how fast the subject is moving, jitter may not be avoided even Movements may not be detected when a moving subject is small, when a moving subject is at
the edge of the screen or when a subject has moved at the very moment when the shutter button was pressed fully. The setting is fixed to [ ] in the following cases. In [SPORTS], [BABY1]/[BABY2] and [PET] in Scene Mode In [INDOOR PORTRAIT] in Advanced Scene Mode Programme Shift cannot be activated when the ISO sensitivity is set to [ ]. You cannot select [ ] in Shutter-Priority AE Mode and Manual Exposure Mode. Also, you cannot select [AUTO] in Manual Exposure Mode. To avoid picture noise, we recommend reducing the ISO sensitivity, setting [NOISE REDUCTION] in [FILM MODE] towards [ _] or setting the items except [NOISE REDUCTION] towards [`] to take pictures. (P118) When [DIRECT FOCUS AREA] (P84) is set to [ON], the operations on the cursor buttons translate to movements of the AF area. Set using the Quick Menu (P56). if [ ] is selected. amount of picture noise.
92
VQT3A48
Recording
[REC] Mode:
Set the aperture value to a higher number when you want a sharp focus background. Set the aperture value to a lower number when you want a soft focus background.
].
] Shutter-priority AE
When you want to take a sharp picture of a fast moving subject, set with a faster shutter speed. When you want to create a trail effect, set to a slower shutter speed.
].
Note It will be a normal motion picture recording when recording a motion picture. How the Exposure Compensation is switched can be changed by [EXPO. SETTINGS] (P133) In the Quick Menu (P56) while in touch operation, setting of the aperture value or shutter speed
can be set by touching the aperture value or shutter speed, and then touching the exposure meter bar. The brightness of the LCD monitor/Viewfinder and the recorded pictures may differ. Check the pictures on the playback screen. Set the aperture value to a higher number when the subject is too bright in Aperture-Priority AE Mode. Set the aperture value to a lower number when the subject is too dim. When you use a lens with an aperture ring, the setting for the rear dial becomes effective if you rotate the aperture ring to the [A] position and the aperture ring setting takes priority if you rotate the aperture ring to a position other than [A] in Aperture-Priority AE Mode.
VQT3A48
93
Recording
The aperture value and the shutter speed displayed on the screen turn red and blink when the We recommend using a tripod when the shutter speed is slow. When the flash is activated, the shutter speed cannot be set to faster than 1/160th of a second If you press the shutter button fully when the shutter speed is slow, the shutter speed on the [ ] and [ ] cannot be set for Shutter-Priority AE Mode. The [SENSITIVITY] is automatically set to [AUTO] when you switch the Recording Mode to
Shutter-Priority AE Mode while the [SENSITIVITY] is set to [ ] (Intelligent). screen counts down in Shutter-Priority AE Mode. in Shutter-Priority AE Mode. (P73) exposure is not adequate.
[REC] Mode:
Set the mode dial to []. Rotate the rear dial to set the aperture and shutter speed.
It will switch between aperture setting operation and
shutter speed setting operation every time the rear dial is pressed. Rotate the rear dial to display the [EXPO.METER]. (P133) You can also set the focus manually by setting the focus mode lever to [MF]. (P85)
A Manual Exposure Assistance The exposure is adequate. Set to faster shutter speed or larger aperture value. Set to slower shutter speed or smaller aperture value. The manual exposure assistance is an approximation. We recommend checking the pictures
on the playback screen.
94
VQT3A48
Recording
About [B] (Bulb) If you set the shutter speed to [B], the shutter stays open while the shutter button is pressed fully (up to about 120 seconds). The shutter closes if you release the shutter button. Use this when you want to keep the shutter open for a long time to take pictures of fireworks, a night scene etc. We recommend using a tripod or the remote shutter (DMW-RSL1; optional) when you take
pictures with the shutter speed set to [B]. Refer to P172 for information about the remote shutter. If you set the shutter speed to [B], [B] is displayed on the screen. When you take pictures with the shutter speed set to [B], use a sufficiently charged battery. (P24) When you take pictures with the shutter speed set to [B], noise may become visible. To avoid picture noise, we recommend setting [LONG SHTR NR] in the [REC] Mode menu to [ON] before taking pictures. (P124) The manual exposure assistance does not appear. It can only be used with Manual Exposure Mode.
Constant preview In Manual Exposure Mode, when [CONSTANT PREVIEW] in the [CUSTOM] menu is [ON], you will be able to confirm the effects of aperture and shutter speed on the screen. (P96) Close the flash. It can only be used with Manual Exposure Mode. Note It will be a normal motion picture recording when recording a motion picture. It is possible to change the switching method of aperture and shutter speed settings with the In the Quick Menu (P56) while in touch operation, setting of the aperture value or shutter speed
can be set by touching the aperture value or shutter speed, and then touching the exposure meter bar. The brightness of the LCD monitor/Viewfinder and the recorded pictures may differ. Check the pictures on the playback screen. If the exposure is not adequate, the aperture value and the shutter speed turn red and blink when the shutter button is pressed halfway. [], [ ], [ ] and [ ] for flash cannot be set. The [SENSITIVITY] is automatically set to [ISO160] when you switch the Recording Mode to Manual exposure while the [SENSITIVITY] is set to [AUTO] or [ ] (Intelligent). If you press the shutter button fully when the shutter speed is slow, the shutter speed on the screen counts down. When you use a lens with an aperture ring, the aperture ring setting takes priority. [EXPO. SETTINGS] (P133) in the [CUSTOM] menu.
VQT3A48
95
Recording
[REC] Mode:
Press [
] A (preview button).
] is pressed.
1 Recording conditions 2 Example: When you want to take a picture with a blurred background etc. 3 Example: When you want to take a picture with everything in focus including the background etc.
Confirm the effects of shutter speed Movement can be confirmed by displaying the actual picture that will be taken with that shutter speed. When the shutter speed is set for high speed, display in the shutter speed preview will be displayed like a time-release film. It is used in cases such as stopping the movement of running water.
] can be changed with [PREVIEW HOLD] of [CUSTOM] menu (P133). It is possible to record while in Preview Mode. Range for shutter speed effect check is 8 seconds to 1/1000th of a second.
VQT3A48
96
Recording
[REC] Mode:
Set the mode dial. Press 2/1 to select the Advanced Scene Mode.
Description of the selected mode is displayed when [DISPLAY]
is pressed. (It will return to the previous screen when pressed again.)
Note To change the Advanced Scene Mode, press [MENU/SET], and return to above step 2 by
pressing 1, while selecting the Advanced Scene Mode menu [ Mode is changed and then used.
The Advanced Scene Mode flash setting is reset to the initial setting when the Advanced Scene When you take a picture with a Advanced Scene Mode that is not adequate for the purpose, The following items cannot be set in Advanced Scene Mode because the camera automatically
adjusts them to the optimal setting. [SENSITIVITY]/Items other than [STANDARD] and [STANDARD] ( ) in Film Mode/ [METERING MODE]/[FLASH SYNCHRO]/[I.RESOLUTION]/[I.DYNAMIC]/[ISO LIMIT SET]/ [DIGITAL ZOOM] the hue of the picture may differ from the actual scene.
] by pressing 3/4/2/1.
About the aperture value and the shutter speed when you select a creative setting You can change the aperture value and the shutter speed if you select
a creative setting in Advanced Scene Mode. If you cannot get an adequate exposure when you rotate the rear dial, the aperture value and the shutter speed or the selection cursor will turn red. You can also press 2/1 to set. It will switch between aperture setting or shutter speed setting operation and Exposure Compensation operation when the rear dial is pressed.
[PORTRAIT] [NORMAL PORTRAIT] [SOFT SKIN] [OUTDOOR PORTRAIT] [INDOOR PORTRAIT] [CREATIVE PORTRAIT]
Technique for Portrait Mode To make this mode more effective: 1 Rotate the zoom ring as far as possible to Tele. 2 Move close to the subject to make this mode more effective.
VQT3A48
97
Recording
PORTRAIT] and [INDOOR PORTRAIT] produce motion pictures using corresponding settings. [CREATIVE PORTRAIT] produces motion pictures using settings suitable for recording people. In [INDOOR PORTRAIT], the Intelligent ISO sensitivity control operates, and the maximum ISO sensitivity level becomes [ISO400]. The initial setting for the AF Mode is []. When [SOFT SKIN] is selected, if a part of the background etc. is a colour close to skin colour, this part is also smoothed. When [SOFT SKIN] is selected, this mode may not be effective when there is insufficient brightness.
Note During motion picture recording, the motion picture will reflect the settings for each
mode with [FLOWER], [FOOD] and [OBJECTS]. [CREATIVE CLOSE-UP] is suitable for near distance motion picture recording. We recommend using a tripod and the self-timer. We recommend setting the flash to [] (close the flash) when you take pictures at close range. Refer to About the focus distance reference mark on P86 for the focus range. When a subject is close to the camera, the effective focus range is significantly narrowed. Therefore, if the distance between the camera and the subject is changed after focusing on the subject, it may become difficult to focus on it again. Close-up Mode gives priority to a subject close to the camera, so it takes longer to focus on the further subjects. When you take pictures at close range, the resolution of the periphery of the picture may decrease slightly. This is not a malfunction. If the lens becomes dirty with fingerprints or dust, the lens may not be able to focus on the subject correctly. The initial setting for the AF Mode is [].
98
VQT3A48
Recording
[REC] Mode:
Taking Pictures that match the Scene being recorded ( : Scene Mode)
When you select a Scene Mode to match the subject and recording situation, the camera sets the optimal exposure and hue to obtain the desired picture.
].
[PERIPHERAL DEFOCUS]
This mode makes it easy to pick out the subject on which to focus and blurs the background to make the subject stand out. Setting the AF area 1 Touch the subject to move the AF area. AF area can also be moved by pressing the cursor button. 2 Touch [SET]. Note It will be a normal motion picture recording during the motion picture recording. Quick AF is performed automatically. Set the [WHITE BALANCE] (P88) using the Quick Menu (P56). AF area setting screen is displayed by pressing the cursor button. Press [] to return the AF The obtained effects will differ depending on factors such as the distance to the subject and
area to the centre of the screen. background, and the type of lens used. For best results, we recommend getting as close as possible to the subject when taking pictures. (P86) AF Mode will be fixed to a small point.
VQT3A48
99
Recording
. [NIGHT PORTRAIT]
This allows you to take pictures of a person and the background with near real-life brightness. Technique for Night Portrait Mode Open the flash. (You can set to [ ].) We recommend using a tripod and the Self-timer for taking pictures. When [NIGHT PORTRAIT] is selected, keep the subject still for about 1 second after taking the
picture.
] are used, which will provide better pictures in dimly lit rooms or at nightfall. The shutter may remain closed after taking the picture. This is due to signal processing and is not a malfunction. Noise may become visible when you take pictures in dark places. The initial setting for the AF Mode is [].
/ [NIGHT SCENERY]
This allows you to take vivid pictures of the nightscape. Technique for Night Scenery Mode We recommend using a tripod and the Self-timer for taking pictures. Note During motion picture recording, low light settings [
] are used, which will provide better pictures in dimly lit rooms or at nightfall. The flash setting is fixed to []. The shutter may remain closed after taking the picture. This is due to signal processing and is not a malfunction. Noise may become visible when you take pictures in dark places. The initial setting for the AF Mode is [ ].
[SUNSET]
Select this when you want to take pictures of a sunset view. This allows you to take vivid pictures of the red colour of the sun. Note The flash setting is fixed to []. The initial setting for the AF Mode is [
].
100
VQT3A48
Recording
2 [PARTY]
Select this when you want to take pictures at a wedding reception, an indoor party etc. This allows you to take pictures of people and the background with near real-life brightness. Technique for Party Mode Open the flash. (You can set to [ ] or [ ].) We recommend using a tripod and the self-timer for taking pictures. Note The initial setting for the AF Mode is [].
- [SPORTS]
Set here when you want to take pictures of sports scenes or other fast-moving events. Note Intelligent ISO sensitivity control is activated, and maximum ISO sensitivity level becomes The initial setting for the AF Mode is [].
[ISO800].
: [BABY1]/; [BABY2]
This takes pictures of a baby with a healthy complexion. When you use the flash, the light from it is weaker than usual. It is possible to set different birthdays and names for [BABY1] and [BABY2]. You can select to have these appear at the time of playback, or have them stamped on the recorded image using [TEXT STAMP] (P145). Birthday/Name setting 1 Press 3/4 to select [AGE] or [NAME] and then press 1. 2 Press 3/4 to select [SET] and then press [MENU/SET]. 3 Enter the birthday or name. Birthday: Name: 2/1: Select the items (year/month/day). 3/4: Setting. [MENU/SET]: Exit. For details on how to enter characters, refer to Entering Text on P117.
When the birthday or name is set, [AGE] or [NAME] is automatically set to [ON]. If [ON] is selected when the birthday or name has not been registered, the setting screen
appears automatically.
To cancel [AGE] and [NAME] Select the [OFF] setting in step 2 of the Birthday/Name setting procedure.
VQT3A48
101
Recording
Note During motion picture recording, settings for [NORMAL PORTRAIT] are used.
Also, still pictures recorded during motion picture recording ([ ] (Motion picture priorities)) (P108) will not record age or name. The age and name can be printed out using the PHOTOfunSTUDIO 6.0 BD Edition bundled software on the CD-ROM (supplied). If [AGE] or [NAME] is set to [OFF] even when the birthday or name has been set, the age or name will not be displayed. Before taking pictures, set [AGE] or [NAME] to [ON]. Intelligent ISO sensitivity control is activated, and maximum ISO sensitivity level becomes [ISO400]. If the camera is turned on with [BABY1]/[BABY2] set, the age and name are displayed at the lower left of the screen for about 5 seconds, along with the current date and time. The initial setting for the AF Mode is [].
[PET]
Select this when you want to take pictures of a pet such as a dog or a cat. You can set your pets birthday and name. For information about [AGE] or [NAME], refer to [BABY1]/[BABY2] on P101. Note It will be a normal motion picture recording during the motion picture recording. The initial setting for the AF Assist Lamp is [OFF]. Intelligent ISO sensitivity control is activated, and maximum ISO sensitivity level becomes The initial setting for the AF Mode is [ ]. Refer to [BABY1]/[BABY2] for other information about this mode.
[ISO800].
102
VQT3A48
Recording
[REC] Mode:
].
Effect This is a pop art style image effect that emphasises the colour. This is a soft image effect that gives the appearance of a tarnished photograph. This is an image effect that uses a cool, bright light to give a feeling of freshness. (The image will come out bright and slightly bluish.) This is an image effect that creates a tranquil atmosphere and projects a feeling of stateliness. (The image will come out slightly dark and amberish.) This is an image effect that captures the subject using tones characteristic of black and white photography, and with a whisper of colour. This is an impressive image effect that adjusts dark areas and bright areas to appropriate brightness, together with enhancements on colours. This is an image effect that enhances the subject in the shade as a black silhouette by using the background colours of the sky or sunset etc. The colour effects can be set according to your preferences.
[MONOCHROME]
[DYNAMIC ART]
[SILHOUETTE] [CUSTOM]
Touch [SET].
Readjust the My Colour settings
Return to above step 2 by pressing rear dial or cursor button.
VQT3A48
103
Recording
Note During Motion Picture Recording, settings for My Colour Mode are used. My Colour settings are memorised even if the camera is turned off. Auto Bracket cannot be used in My Colour Mode. ISO sensitivity will be fixed to [AUTO]. [I.DYNAMIC], [COLOR SPACE] can be set only when the My Colour Mode is set to [CUSTOM]. The following items cannot be set in My Colour Mode because the camera automatically
adjusts them to the optimal setting. [FILM MODE]/[FLASH]/[FLASH SYNCHRO]/[ISO LIMIT SET]
Adjusting the custom settings to achieve desired effects By selecting [CUSTOM], you can take pictures with colour, brightness and saturation adjusted to desired levels.
1 2
3 4
Return [CUSTOM] settings to default 1 Touch [ ] in above step 2. 2 Touch [YES]. Adjusted value for each item returns to standard (centre point). Note Adjustments made with [CUSTOM] are not in effect in other Recording Modes. Icons for the adjusted items are displayed in the screen when the [CUSTOM] are adjusted. AF tracking may not function if you adjust [SATURATION] to make the colour lighter.
Displayed icon is the one for direction of adjustment.
104
VQT3A48
Recording
[REC] Mode:
], [
] or [
].
Saving of the selected custom settings is displayed on the screen. A Registering Personal Menu Settings (Registering custom settings) It is possible to register up to 3 sets of current camera settings as custom sets. Set to the mode dial to the desired mode and select the desired menu settings in advance.
1 2
Select [CUST. SET MEM.] in the [CUSTOM] menu. (P55) Press 3/4 to select the custom set to register and then press [MENU/SET].
Custom set [ [ [ Recording location ] on the mode dial ] on the mode dial ] on the mode dial
Press 3 to select [YES] and then press [MENU/SET]. When [YES] is selected, the settings that were previously stored are overwritten. ] selected,
When changing the menu settings Even if the menu settings are changed temporarily with [ ], [ ] or [ what has been registered will remain unchanged. To change what has been registered, overwrite the registered data using [CUST. SET MEM.] on the [CUSTOM] menu.
Note You cannot save the following menu items because they affect other Recording Modes.
[REC] menu/Recording functions [BABY1]/[BABY2] or [PET] birthday and
[SETUP] menu [CLOCK SET] [WORLD TIME] [TRAVEL DATE] [LCD MODE] [FAVORITE FUNC.] [MENU GUIDE] [LANGUAGE]
VQT3A48
105
Recording
[REC] Mode:
Recording
].
[24P CINEMA]
Record motion pictures with afterimages like a cinema. Note Record motion pictures in AVCHD format. [REC QUALITY] can be set to either [
(P128) ] or [ ].
106
VQT3A48
Recording
Note Display of the motion picture recording time at the top right of the screen is different from
normal motion picture for [VARIABLE MOVIE MODE] playback. [ ]: Actual playback time [ ]: Actual recording time of the motion picture during recording Record motion pictures in AVCHD format. [REC QUALITY] can be set to either [ ] or [ ]. (P128) Audio is not recorded. [WIND CUT], [MIC LEVEL DISP.] and [MIC LEVEL ADJ.] in the [MOTION PICTURE] Mode menu cannot be used. We recommend using a tripod.
Changing the aperture/shutter speed manually and recording motion pictures Select the following settings from [EXPOSURE MODE] in the [MOTION PICTURE] Mode menu. Rotate the rear dial on the recording screen to change the aperture value and shutter speed. Items that can be set will switch every time the rear dial is pressed.
[EXPOSURE MODE] P (Programme AE Mode) A (Aperture-Priority AE Mode) S (Shutter-Priority AE Mode) Aperture F4.0 (Wide)/F5.8 (Tele) to F221 F3.5 (Wide)/F5.6 (Tele) to F222 Shutter speed (Sec.) 1/25 to 1/4000th Shutter speed (Sec.) M (Manual Exposure Mode) 1/25 to 1/4000th (when set to [AFS] or [AFC]) 1/2 to 1/4000th (when set to [MF]) Exposure Compensation Items that can be set Exposure Compensation
Exposure Compensation Aperture F4.0 (Wide)/F5.8 (Tele) to F221 F3.5 (Wide)/F5.6 (Tele) to F222
1 When the 14 140 mm/F4.0 5.8 lens supplied in DMC-GH2H is used 2 When the 14 42 mm/F3.5 5.6 lens supplied in DMC-GH2K is used Shutter speed changes depending on the selected Motion Picture Mode and [FRAME RATE] setting. You can change the settings and switch settable items even during motion picture recording. However please note that operating sounds may be recorded.
VQT3A48
107
Recording
Note Aperture value Set the aperture value to a higher number when you want a sharp focus background. Set the Shutter speed When you want to take a sharp picture of a fast moving subject, set with a faster shutter Manually setting a higher shutter speed may increase the noise on-screen due to the higher sensitivity. Colour or brightness of the image may change, or you may see horizontal bars on the sides
speed. When you want to create a trail effect, set to a slower shutter speed. aperture value to a lower number when you want a soft focus background.
of the image when the subject is recorded in an extremely bright place or under fluorescent light, mercury light, sodium light, etc. In this case, record in another recording mode or manually adjust the shutter speed to 1/60 or 1/100. Refer to Recording Motion Picture on P43 for other settings and operations for recording motion pictures.
[REC] Mode:
During motion picture recording, press the shutter button fully to record a still picture.
Simultaneous recording indicator A is displayed while You can also take pictures using the Touch Shutter function
(P38). recording still pictures.
Setting motion picture and still picture priorities 1 Select [PICTURE MODE] from the [MOTION PICTURE] Mode menu. (P55) 2 Press 3/4 to select the item and then press [MENU/SET].
Item
Settings Pictures will be recorded with a picture size of [S] (2 M). The
picture quality may be different to [S] (2 M) of standard pictures.
[ ], [ ] or [ ]. (When set to [ ], still pictures will be recorded in [QUALITY] of [A].) Up to 30 still pictures can be recorded during recording of the motion picture.
Pictures will be recorded with the set picture size and quality. The screen will go dark while recording pictures. A still picture (Still picture priorities) Up to 8 still pictures can be recorded during recording of the
motion picture. will be recorded in the motion picture during that period, and audio is not recorded.
Note The picture aspect ratio will be fixed to [W]. Simultaneous recording is not possible in the following cases: When [MOTION JPEG] is set to [ ] or [ ] When [EX. TELE CONV.] is used [only when [ ] (still picture priorities) is set]
108
VQT3A48
Recording
[REC] Mode:
In Recording Mode Display of corresponding name when camera detects a registered The camera will remember the face that has been photographed
face (if name has been set for the registered face)
many times and display the registration screen automatically (if [AUTO REGISTRATION] is set to [ON]) In Playback Mode Display of name and age (if information has been registered) Selective playback of pictures chosen from pictures registered with Face Recognition ([CATEGORY PLAY] (P143)) Names of up to 3 people are displayed. Precedence for the names displayed when taking pictures is determined according to the order of registration.
Note [FACE RECOG.] only works when the AF Mode is set to []. During the Burst Mode, [FACE RECOG.] picture information can be attached to only the first After pressing the shutter halfway down, a different persons picture information may be added [FACE RECOG.] cannot be used with the [FOOD] in [CLOSE-UP], [NIGHT SCENERY] and When the Focus Mode is set to [MF], automatic registration is not available. [FACE RECOG.] will find a face similar to the registered face, and does not guarantee secure Face Recognition may take more time to select and recognise distinctive facial features than Even when face recognition information has been registered, pictures taken with [NAME] set to Even when Face Recognition information is changed (P113), Face Recognition
[OFF] will not be categorized by face recognition in [CATEGORY PLAY]. information for the pictures already taken will not be changed. For instance, if the name is changed, pictures recorded before the change will not be categorized by face recognition in [CATEGORY PLAY]. To change the name information of the pictures taken, perform the [REPLACE] in [FACE REC EDIT] (P153). regular Face Detection. recognition of a person. [PERIPHERAL DEFOCUS] in Scene Mode and in recording motion pictures. when the camera is turned to a different subject to photograph. picture.
VQT3A48
109
Recording
Face Settings You can register information such as names and birthdays for face images of up to 6 people. Registration can be facilitated by taking multiple face images of each person. (up to 3 pictures/registration) Point of recording when registering the face images
outline of the face, the eyes, or the eyebrows are not covered with the hair when registering. Make sure there is no extreme shading on the face when registering. (Flash will not flash during registration.)
Face front with eyes open and mouth closed, making sure the
When it is not recognising during recording Register the face of same person indoors and outdoors, or with different expressions or Additionally register at the location of recording. Changing the [SENSITIVITY] setting. (P113) When a person who is registered is not recognised, correct by re-registering. Example of faces that are hard to recognise
Face Recognition may not be possible or may not recognise faces correctly even for registered faces in the following instances, depending on the facial expression and environment. Hair is covering the eyes or the eyebrows (A) The face is dark/the light is at an angle (B) The face is facing in angle or sideways The face is facing upward/downward The eyes are closed When the face is extremely bright or dark Hidden by sunglasses, glasses reflecting light, hair, hat, etc. When the face appears small on the screen The entire face is not in the screen When distinctive facial features have changed with age When parents and children or siblings closely resemble one another Facial expression is very different When there is little contrast on the faces When there is rapid movement When the camera is shaking When Digital Zoom is used angles. (P113)
110
VQT3A48
Recording
Select [FACE RECOG.] on the [REC] Mode menu and then press 1. (P55) Press 3/4 to select [MEMORY] and then press [MENU/SET]. Press 3/4/2/1 to select the face recognition frame that is not registered, and then press [MENU/SET]. Take the picture adjusting the face with the guide.
The faces of subjects other than people (pets, etc.) When recognition fails, a message will appear and
cannot be registered. the display will return to the recording screen. In this case, try taking the picture again.
VQT3A48
111
Recording
[NAME]
It is possible to register names. 1 Press 4 to select [SET] and then press [MENU/SET]. 2 Enter the name. For details on how to enter characters, refer to Entering Text
section on P117.
[AGE]
It is possible to register the birthday. 1 Press 4 to select [SET] and then press [MENU/SET]. 2 Press 2/1 to select the items (Year/Month/Day), and then press 3/4 to set and then press [MENU/SET]. To add additional face images. (Add Images) 1 Select the unregistered face recognition frame, and then press [MENU/SET]. 2 Perform steps 4 and 5 in Registering face image of new person. 3 Press []. To delete one of the face images. (Delete) 1 Press 2/1 to select the face image to delete, and then press [MENU/SET]. 2 Press 3 to select [YES] and then press [MENU/SET]. 3 Press []. If there is only one image registered, it cannot be deleted.
[ADD IMAGES]
explanation appears for taking face images. (Press again to return to the recording screen.)
112
VQT3A48
Recording
Change or delete the information for a registered person You can modify the pictures or information of an already registered person. You can also delete the information of the registered person.
1 2 3 4
Select [FACE RECOG.] from the [REC] Mode menu, and then press 1. (P55) Press 4 to select [MEMORY] and press [MENU/SET]. Press 3/4/2/1 to select the face image to edit or delete and then press [MENU/SET]. Press 3/4 to select the item and then press [MENU/SET].
Item [INFO EDIT] Description of settings
Changing the information of an already registered person. Perform step 6 in Registering face image of new person. The focus and exposure are preferentially adjusted for higher-priority faces. Press 3/4/2/1 to select the priority and then press [MENU/SET]. Deleting information of a registered person. Press 3 to select [YES] and then press [MENU/SET].
[PRIORITY]
[DELETE]
Press the shutter button halfway to close the menu. Setting Auto Registration/Sensitivity
Setting of Auto Registration and Sensitivity for Face Recognition can be done.
1 2 3
Select [FACE RECOG.] from the [REC] Mode menu, and then press 1. (P55) Press 4 to select [SET] and then press [MENU/SET]. Press 3/4 to select the item and then press 1.
Item [AUTO REGISTRATION] Description of settings
[OFF]/[ON] When the [AUTO REGISTRATION] is set to [ON], For details, see Auto Registration on P114.
[FACE RECOG.] will be set to [ON] automatically.
Select [LOW] when mistaken recognition happens frequently. To return to the original settings, select [NORMAL].
VQT3A48
113
Recording
Auto Registration When [AUTO REGISTRATION] is set to [ON], the registration screen will display automatically after taking a picture of a face that has a high number of appearances. Registration screen is displayed after approximately 3 pictures. It may be extremely hard to recognise only with [AUTO REGISTRATION], so register the face
images with [FACE RECOG.] in the [REC] Mode menu beforehand.
Registering from the automatic registration screen 1 Press 3 to select [YES] and then press [MENU/SET]. If there are no registered persons, proceed to step 3. Selection screen is displayed again when [NO] is selected, and when [YES] is selected with 3, [AUTO REGISTRATION] will be
Press 3/4 to select [NEW PERSON] or [ADDITIONAL IMAGE] and then press [MENU/SET].
Item [NEW PERSON] Description of settings
set to [OFF].
To additionally register a face image for a registered person. Press 3/4/2/1 to select the person to whom you wish add the picture, and then press [MENU/SET]. [ADDITIONAL IMAGE] If 3 images have already been registered, the picture
replacement screen will appear. In this case, select the picture you wish to replace.
After additionally registering or changing a face image, the screen returns automatically to
the recording screen.
Perform the operation in Step 6 and following in Registering face image of new person.
Note If the registration screen will not display, it may display easier by recording in the same If a face is not recognised even though it is registered, it will make the recognition easier by
registering the person again using the [FACE RECOG.] in the [REC] Mode menu in that environment. If the registration screen is displayed for a person that is already registered, it will make the recognition easier by additionally registering. It may make recognition harder when a picture recorded with flash is registered. conditions or with the same expressions.
114
VQT3A48
Recording
[REC] Mode:
1 2 3 4
Select [TRAVEL DATE] from the [SETUP] menu, and then press 1. Press 3 to select [TRAVEL SETUP] and then press 1. Press 4 to select [SET] and then press [MENU/SET]. Press 3/4/2/1 to set the departure date (year/month/day), and then press [MENU/SET].
Press 3/4/2/1 to set the return date (year/month/day), and then press [MENU/SET]. If you do not want to set the return date, press [MENU/SET] while
the date bar is displayed.
6 7 8 9
Press 4 to select [LOCATION] and then press 1. Press 4 to select [SET] and then press [MENU/SET]. Enter the location. For details on how to enter characters, refer to Entering Text on P117. Press [MENU/SET] twice to close the menu. The number of days that have passed since the departure date is displayed for about
5 seconds if this unit is turned on etc. after setting the travel date or when the travel date is set. When the travel date is set, [] appears on the lower right of the screen.
Cancelling the travel date The travel date is automatically cancelled if the current date is after the return date. If you want to cancel the travel date before the end of the vacation, select [OFF] on the screen shown in step 3 or 7 and then press [MENU/SET] twice. If the [TRAVEL SETUP] is set to [OFF] in step 3, [LOCATION] will be also set to [OFF]. Note The travel date is calculated using the date in the clock setting and the departure date you set.
If you set [WORLD TIME] (P116) to the travel destination, the travel date is calculated using the date in the clock setting and the travel destination setting.
VQT3A48
115
Recording
The travel date setting is memorised even if the camera is turned off. If [TRAVEL DATE] is set to [OFF], the number of days that have passed since the departure
date will not be recorded. Even if [TRAVEL DATE] is set to [SET] after taking the pictures, which day of the vacation you took them is not displayed. If you set a departure date and then take a picture on a date before this departure date, [-] (minus) is displayed in orange and the day of the vacation that you took the picture is not recorded. If the travel date is displayed as [-] (minus) in white, there is a time difference that involves date change between the [HOME] and [DESTINATION]. (It will be recorded) [TRAVEL DATE] cannot be recorded for motion pictures recorded with [AVCHD]. [LOCATION] cannot be recorded when taking motion pictures. [TRAVEL DATE] cannot be set in the Intelligent Auto Mode. Setting of other Recording Mode will be reflected.
Recording Dates/Times at Overseas Travel Destinations (World Time) For details on the [SETUP] menu settings, refer to P55. You can display the local times at the travel destinations and record them on the pictures you take. Select [CLOCK SET] to set the current date and time in advance. (P31)
1 2 3
Select [WORLD TIME] from the [SETUP] menu, and then press 1. When first using the camera after purchasing it, the [PLEASE SET THE HOME AREA] Press 4 to select [HOME], and then press [MENU/SET]. Press 2/1 to select the home area, and then press [MENU/SET].
message appears. Press [MENU/SET], and set the home area on the screen in step 3.
A Current time B Time difference from GMT (Greenwich Mean Time) If daylight saving time [ ] is used at the home area, press B 3. Press 3 again to return to the original time. The daylight saving time setting for the home area does not advance the current time. Advance the clock setting by one hour.
Press 2/1 to select the area the travel destination is in D and then press [MENU/SET] to set.
D Current time of the destination area E Time difference If daylight saving time [ ] is used at the travel destination, E press 3. (The time advances by one hour.) Press 3 again to return to the original time.
Note Return the setting to [HOME] when the vacation is finished by performing steps 1, 2 and 3. If [HOME] is already set, change only the travel destination, and use. If you cannot find the travel destination in the areas displayed on the screen, set by the time
difference from the home area.
VQT3A48
116
Recording
Entering Text
It is possible to enter babies and pets names and the names of travel destinations when recording. (Only alphabetical characters and symbols can be entered.)
Display the entry screen and press 4 to move to the character selection section.
You can display the entry screen via the following operations. [NAME] of [BABY1]/[BABY2] or [PET] (P101) in Scene Mode. [NAME] in [FACE RECOG.] (P112) [LOCATION] in [TRAVEL DATE] (P115) [TITLE EDIT] (P144)
Press 3/4/2/1 to move the cursor to [SET] and then press [MENU/SET] to end text input.
Display will return to the appropriate setting screen. Note Text can be scrolled if all of the entered text does not fit on the screen.
VQT3A48
117
Recording
[FILM MODE]
You can select up to 10 different colour tones and contrasts for the recorded pictures to match the recording conditions and aspects, as you would select different films for film cameras. Applicable modes: [You can only select [STANDARD] (COLOUR) and [STANDARD] ( [ ], [ ] and [ ] mode.] ) in [ ], [],
[STANDARD] (COLOUR)/[DYNAMIC] (COLOUR)/[SMOOTH] (COLOUR)/[NATURE] )/ (COLOUR)/[NOSTALGIC] (COLOUR)/[VIBRANT] (COLOUR)/[STANDARD] ( [DYNAMIC] ( )/[SMOOTH] ( )/[MY FILM 1]/[MY FILM 2]/[MULTI FILM]/[CINEMA] (COLOUR)
Note In Film Mode, the camera may do something equivalent to pull processing or push processing
to create a picture with particular characteristics. The shutter speed may become very slow at this time. Use the Quick Menu (P56) to set when in Intelligent Auto Mode.
Touch [2]/[1] to select an item. When you touch [ ] on the screen shown right, explanations Touch [SET].
about each Film Mode are displayed. (When you touch [CANCEL], the screen returns to the previous screen.)
1 2 3 4
Touch the item. Touch the slide bar. Registered settings are memorised even if the camera Touch [MEMORY]. Touch [MY FILM 1] or [MY FILM 2]. You can register 2 settings. ([MY FILM 1] and
is turned off.
[MY FILM 2]) (After registering, the Film Mode name that was registered previously is displayed.) [STANDARD] is registered in [MY FILM 1] and [MY FILM 2] at the time of purchase.
Touch [SET].
VQT3A48
118
Recording
Item [CONTRAST]
Effect Increases the difference between the brightness and the [r] darkness in the picture. [s] Decreases the difference between the brightness and the darkness in the picture.
S [SHARPNESS]
[r] The picture is sharply defined. [s] The picture is softly focused. [r] The colours in the picture become vivid. [s] The colours in the picture become natural. [r] [s] The noise reduction effect is enhanced. Picture resolution may deteriorate slightly. The noise reduction effect is reduced. You can obtain pictures with higher resolution.
[SATURATION]
[NOISE REDUCTION]
Note Noise may become visible when you take pictures in dark places. To avoid picture noise, we
recommend setting [NOISE REDUCTION] towards [_] or setting the items except [NOISE REDUCTION] towards [`] to take pictures. If you adjust a Film Mode, [_] is displayed beside the Film Mode icon on the screen. You cannot adjust [SATURATION] in the black and white settings in Film Mode. Film Mode cannot be adjusted in the Intelligent Auto Mode, Advanced Scene Mode and Scene Mode.
Multi Film Bracket It will take pictures changing the type of film in accordance with the setting every time the shutter button is pressed. (Up to 3 pictures)
1 2
Touch [2]/[1] to select [MULTI FILM]. Select [MULTI FILM 1], [MULTI FILM 2], or [MULTI FILM 3], and then touch [2]/[1] to select the film to be set for each. [OFF] can be selected only for [MULTI FILM 3]. Touch [SET]. Multi film indication ([ ]) displayed on the screen will
flash until all pictures of preset amount are taken.
Note Motion pictures are recorded with the settings for the [MULTI FILM 1] setting.
VQT3A48
119
Recording
? [ASPECT RATIO]
This allows you to select the aspect ratio of the pictures to suit printing or the playback method. Applicable modes: [X]: [ASPECT RATIO] of a 4:3 TV [Y]: [ASPECT RATIO] of a 35 mm film camera [W]: [ASPECT RATIO] of a high-definition TV, etc. [ ]: Square aspect ratio
[X] [Y] [W] [ ]
Note The ends of the recorded pictures may be cut at printing so check before printing. (P193)
@ [PICTURE SIZE]
Set the number of pixels. The higher the numbers of pixels, the finer the detail of the pictures will appear even when they are printed onto large sheets. Applicable modes: When the aspect ratio is [X].
(16M) (8M) (4M) 4608k3456 pixels 3264k2448 pixels 2336k1752 pixels
120
VQT3A48
Recording
].
] is displayed on the screen when the picture size is set to a size other than the maximum picture size for each aspect ratio.
higher the numbers of pixels, the finer the picture will be when it is printed on a large piece of paper or displayed on a PC monitor. A Many pixels (Fine) B Few pixels (Rough) These pictures are examples to show the effect. If you change the aspect ratio, set the picture size again. Refer to P30 for information about the number of recordable pictures.
A [QUALITY]
Set the compression rate at which the pictures are to be stored. Applicable modes: [A]: []: [ [ [ ]: Fine (when giving priority to the picture quality) Standard (when using the standard picture quality and increasing the number of pictures to be recorded without changing the number of pixels) ]: RAWiFine (In addition to the [RAW] settings, a fine-equivalent JPEG image is simultaneously created.)1 ]: RAWiStandard (In addition to the [RAW] settings, a standard-equivalent JPEG image is simultaneously created.)1 RAW file (When the image is to be edited with a PC in high quality)2
1 If you delete a RAW file from the camera, the corresponding JPEG image will also be deleted. 2 It is fixed to maximum recordable pixels ([L]) for each image aspect ratio.
Note Refer to P30 for information about the number of recordable pictures. You can enjoy more advanced picture editing if you use RAW files. You can save RAW files in a
file format (JPEG, TIFF etc.) that can be displayed on your PC etc., develop them and edit them using the software SILKYPIX Developer Studio by Ichikawa Soft Laboratory on the CD-ROM (supplied). [ ] images are recorded with a smaller data volume than [ ] or [ ]. [PRINT SET] and [FAVORITE] cannot be set to a picture taken by [ ].
VQT3A48
121
Recording
[FACE RECOG.]
[OFF]/[ON]/[MEMORY]/[SET] Note Refer to P109 for details.
C [METERING MODE]
Type of optical measurement to measure brightness can be changed. Applicable modes: [C]: Multiple This is the method in which the camera measures the most suitable exposure by judging the allocation of brightness on the whole screen automatically. Usually, we recommend using this method. [ ]: Centre weighted This is the method used to focus on the subject on the centre of the screen and measure the whole screen evenly. []: Spot This is the method to measure the subject in the spot metering target A.
Note When the AF Mode is set to [] while [C] is selected, exposure is adjusted to the face of a
person, and when it is set to [ ], exposure is adjusted to the locked subject.
[STABILIZER]
[OFF]/[MODE1]/[MODE2]/[MODE3] Note Refer to P75 for details.
[FLASH]
[]/[ ]/[]/[ ]/[ ]/[ ] Note Refer to P69 for details.
122
VQT3A48
Recording
[RED-EYE REMOVAL]
[OFF]/[ON] Note Refer to P70 for details.
[FLASH SYNCHRO]
2nd curtain synchro activates the flash just before the shutter closes when taking pictures of moving objects such as cars using a slow shutter speed. Applicable modes:
[1ST]:
1st curtain synchro The normal method when taking pictures with the flash.
[2ND]:
2nd curtain synchro The light source appears behind the subject and picture becomes dynamic.
Note Set it to [1ST] normally. [2nd] is displayed in the flash icon on the screen if you set [FLASH SYNCHRO] to [2ND]. The flash sync. settings are also effective when using an external flash. (P171) When a fast shutter speed is set, the effect of [FLASH SYNCHRO] may deteriorate. You cannot set [ ], [ ] or [ ] when [FLASH SYNCHRO] is set to [2ND]. It can only be set with [PERIPHERAL DEFOCUS] in Scene Mode.
[FLASH ADJUST.]
Note Refer to P74 for details.
[I.RESOLUTION]
Pictures with sharp profile and resolution can be taken by utilising the Intelligent Resolution Technology. Applicable modes: [OFF]/[LOW]/[STANDARD]/[HIGH]/[EXTENDED] Note [EXTENDED] allows you to take natural pictures with a higher resolution. The speed of burst and continuous recording becomes slower when [EXTENDED] is used. [EXTENDED] does not work during motion picture recording. Use the Quick Menu (P56) to set when in Creative Motion Picture Mode.
VQT3A48
123
Recording
124
VQT3A48
Recording
) [DIGITAL ZOOM]
[OFF]/[2t]/[4t] Note Refer to P67 for details.
[BURST RATE]
[SH]/[H]/[M]/[L] Note Refer to P77 for details.
[AUTO BRACKET]
[ / SETTINGS]/[STEP]/[SEQUENCE] Note Refer to P79 for details.
[ASPECT BRACKET]
Pressing the shutter button once automatically takes four pictures with aspect ratios of [X], [Y], [W] and [ ]. Applicable modes: [OFF]/[ON] Note When setting Aspect Bracket, [ ] appears on the screen. Picture size is automatically changed to [M] when it is set to [S]. When Aspect Bracket is set, the Auto Review function is activated regardless of the Auto [ ], [ ] or [ ] for [QUALITY] cannot be set. This does not operate during motion picture recording.
Review setting. You cannot set the Auto Review function in the [SETUP] menu.
[SELF-TIMER]
[ ]/[ ]/[ ] Note Refer to P81 for details.
VQT3A48
125
Recording
[COLOR SPACE]
Set this when you want to correct the colour reproduction of the recorded pictures on a PC, printer etc. Applicable modes: [sRGB]: Colour space is set to sRGB colour space. This is widely used in computer related equipment.
[AdobeRGB]: Colour space is set to AdobeRGB colour space. AdobeRGB is mainly used for business purposes such as professional printing because it has a greater range of reproducible colours than sRGB. Note Depending on the colour space setting, the file name of the recorded picture changes as
shown.
126
VQT3A48
Recording
[REC MODE]
This sets up the data format of motion pictures. Applicable modes: [ [AVCHD(1080i)]]/[ [AVCHD(720p)]] Select this format to record HD (high-definition) video for playback on your HDTV using an It can be played back as is by inserting the card into a device compatible with AVCHD. Refer to Use a card with SD Speed Class with Class 4 or higher. [AVCHD(1080i)] can record motion pictures with even higher definition and picture quality than
[AVCHD(720p)]. the instructions of the device used for details on compatibility. HDMI connection.
[ [MOTION JPEG]] Select this format to record standard definition video for playback on your PC. It can be
recorded using less storage when there is not much space left on the memory card or when you want to attach the motion picture to an e-mail. Use a card with SD Speed Class with Class 6 or higher.
[REC QUALITY]
This sets up the picture quality of motion pictures. Applicable modes: When [AVCHD(1080i)] is selected
Item ([FSH]) ([FH]) Quality (bit rate)1 1920k1080 pixels Approx. 17 Mbps2 1920k1080 pixels Approx. 13 Mbps2 fps 50i Aspect ratio
16:9
16:9
VQT3A48
127
Recording
When [24P CINEMA] or [VARIABLE MOVIE MODE] is selected in the Creative Motion Picture Mode
Item ([24H]) ([24L]) Quality (bit rate)1 1920k1080 pixels Approx. 24 Mbps2 1920k1080 pixels Approx. 17 Mbps2 fps Aspect ratio
24p
16:9
] on equipment other than this unit, a compatible Blu-ray disk recorder or PHOTOfunSTUDIO 6.0 BD Edition is required. (P162)
1 What is bit rate This is the volume of data for definite period of time, and the quality becomes higher when the number gets bigger. This unit is using the VBR recording method. VBR is an abbreviation of Variable Bit Rate, and the bit rate (volume of data for definite period of time) is changed automatically depending on the subject to record. Therefore, the recording time is shortened when a subject with fast movement is recorded. 2 What is Mbps This is an abbreviation of Megabit Per Second, and it represents the speed of transmission.
Picture size 1280k720 pixels 848k480 pixels 640k480 pixels 320k240 pixels
fps
([VGA]) ([QVGA])
30 4:3
3 This item cannot be set in the Intelligent Auto Mode. With the [AVCHD] or [ ] for [MOTION JPEG], high quality motion picture can be enjoyed on the TV by using the HDMI mini cable (optional). For details, see Playing back on the TV with HDMI socket on P158.
[EXPOSURE MODE]
[P]/[A]/[S]/[M] Note Refer to P107 for details.
! [PICTURE MODE]
[ ] (Motion picture priorities)/[ ] (Still picture priorities) Note Refer to P108 for details.
128
VQT3A48
Recording
[CONTINUOUS AF]
[OFF]/[ON] Note Refer to P43 for details.
[WIND CUT]
This reduces the wind noise in the audio recording. Applicable modes: [OFF]/[LOW]/[STANDARD]/[HIGH] Note Sound quality will be different than usual when [WIND CUT] is set.
[REC HIGHLIGHT]
White saturated areas appear blinking in black and white. Applicable modes: [OFF]/[ON] Note If there are any white saturated areas, we recommend compensating the exposure towards
negative (P76) referring to the histogram (P66) and then taking the picture. It may result in a better quality picture.
VQT3A48
129
Recording
]/[
]/[
[OFF]/[ON]
[OFF]/[
]/[
]/[
Refer to P65 for details. When the Auto Review function is activated or when playing back, white saturated areas appear blinking in black and white. [OFF]/[ON] If there are any white saturated areas, we
recommend compensating the exposure towards negative (P76) referring to the histogram (P66) and then taking the picture again. It may result in a better quality picture. There may be white saturated areas if the distance between the camera and the subject is too close when taking pictures with the flash. If [HIGHLIGHT] is set to [ON] in this case, the area directly illuminated by the photo flash will become white saturated and appear blinking in black and white. The LCD/LVF will display overexposed portions of the image as white blinking areas. These only exist on the cameras display, not on the actual photo. This does not work while in Multi Playback (P40), Calendar Playback (P41), or Playback Zoom (P42). [AF/AE LOCK]
[HIGHLIGHT]
[ON]
[OFF]
[AE]/[AF]/[AF/AE]
130
VQT3A48
Recording
This will set the operation of [AF/AE LOCK] button when taking a picture with fixed focus or exposure. [OFF]:
[AF/AE LOCK HOLD]
The focus and the exposure are fixed only while you are pressing [AF/AE LOCK]. (P87) If you release [AF/AE LOCK], AF/AE Lock is cancelled. The focus and the exposure remain fixed even if you release [AF/AE LOCK] after pressing it. If you press [AF/AE LOCK] again, AF/AE Lock is cancelled.
[ON]:
Depending on the setting, camera will adjust the focus automatically before pressing the shutter button halfway. [PRE AF] [OFF] [ [ ]: Quick AF ]: Continuous AF
About [ ] and [ ] [ ] will adjust the focus automatically when the jitter of the camera gets small. [ ] will adjust the focus at all times (continuous AF operation). The camera will adjust the focus automatically, and the focus adjustment when the shutter button is pressed becomes faster. It is effective when you do not want to miss the photo opportunity. Note The battery will be consumed faster than usual. Press the shutter button halfway again when it is difficult to focus on the subject. When [PRE AF] is set to [ ], it may take time to focus on the subject if you rotate the zoom [PRE AF] does not work during the Preview Mode. [PRE AF] will not work in low illumination. [PRE AF] does not work with lenses that do not allow Auto Focus and Four Thirds mount
specification lens not compatible to contrast AF. [ Focus Mode cannot be set to [AFC]. (P20) ring from Wide to Tele or suddenly change the subject from a distant one to a nearby one.
[OFF]/[ON]
Refer to P84, 85 for details. It will set so no picture can be taken when it is out of focus. [OFF]:
[FOCUS PRIORITY]
This gives priority to the best time to take a picture so you can take a picture when the shutter button is pressed fully. You cannot take a picture until the subject is brought into focus.
[ON]:
If you set [OFF], be careful as the picture may not be properly focused even if [AFS] or [AFC] in This does not operate during motion picture recording.
VQT3A48
131
Recording
[SHUTTER AF]
Set whether or not the focus is adjusted automatically when the shutter button is pressed halfway. [OFF]/[ON] Illuminating the subject makes it easier for the camera to focus when recording in low light conditions that make focusing difficult. [OFF]: The AF Assist Lamp does not turn on. When taking pictures in dark places, the AF Assist Lamp lights while the shutter button is pressed halfway. (Larger AF areas are displayed depending on the recording conditions.)
[ON]:
The effective range of the AF Assist Lamp is different depending on used lens. When the 14 140 mm/F4.0 5.8 lens supplied in DMC-GH2H is attached and at When the 14 42 mm/F3.5 5.6 lens supplied in DMC-GH2K is attached and at The AF Assist Lamp is valid only for the subject in the centre of the screen. Use it by Remove the lens hood. When you do not want to use the AF Assist Lamp (e.g. when taking pictures of animals in dark
places), set the [AF ASSIST LAMP] to [OFF]. In this case, it will become more difficult to focus on the subject. The AF Assist Lamp gets slightly blocked when the lens supplied in the DMC-GH2H/ DMC-GH2K is used, but it does not affect the performance. The AF Assist Lamp may be greatly blocked, and it may become harder to focus when a lens with large diameter is used. The setting for the [AF ASSIST LAMP] is fixed to [OFF] in [SCENERY] Mode and [NIGHT SCENERY], [SUNSET] in Scene Mode. positioning the subject in the centre of the screen. Wide: Approx. 1.0 m (3.28 feet) to 3.0 m (9.84 feet) Wide: Approx. 1.0 m (3.28 feet) to 3.0 m (9.84 feet)
[ON]:
It is possible to finely adjust the focus manually by rotating the focus ring while AF lock (Focus Mode is set to [AFS] and shutter button is half-way pressed, or AF lock with [AF/AE LOCK]).
[MF ASSIST]
[OFF]/[ON]
[OFF]/[ON]
132
VQT3A48
Recording
This will set the operation of the [ preview screen. [OFF]: [PREVIEW HOLD] [ON]:
Preview screen is displayed only when the [ ] is pressed. It will return to previous screen when [ ] is released. Preview screen is displayed even after the [ ] is released after pressing. (P96) It will return to previous screen when [ ] is pressed again.
[EXPO.METER]
Unsuitable areas of the range are displayed in red. When [EXPO.METER] is not displayed, switch the display information The [EXPO.METER] disappears after approximately
Change the method of Exposure Compensation setting switching when the mode dial is set to , , and .
[EXPO. SETTINGS] [SWITCH BY PRESSING THE REAR DIAL]: Press the rear dial to switch between Exposure Compensation, Programme Shift, aperture setting, and shutter speed setting. [SWITCH BY PRESSING THE LVF/LCD BUTTON]:
Press [LVF/LCD] to switch between Exposure Compensation, Programme Shift, aperture setting, and shutter speed setting. Setting items for each [REC] Mode or
You cannot switch between LCD monitor and viewfinder by pressing [LVF/LCD] when it is set to [EXPO. SETTINGS] is disabled when you set [AUTO SWITCH] in [LVF/LCD SWITCH] to [OFF].
VQT3A48
133
Recording
[LVF DISP.STYLE]
]/[
]/[
Refer to P64 for details. This will set the colour of the information display screen on the LCD monitor. (P64)
[LCD INFO.DISP.]
It will switch automatically to viewfinder display when an eye or object gets near the viewfinder using an eye sensor. It will return to LCD monitor display when it goes away.
[LVF/LCD SWITCH]
[AUTO SWITCH]: Enables/disables the eye sensor. [OFF]/[ON] [SENSITIVITY]: This will set the sensitivity of the eye sensor. [LOW]/[HIGH]
LCD monitor display and viewfinder display can be switched manually by pressing [LVF/LCD].
(P16)
BUTTON]
Enables/disables the motion picture button. [OFF]/[ON] This changes the angle of view during motion picture recording and still picture recording. [!] (Picture)/[ ] (Motion picture)
REC AREA]
The recording area indicated is a guide line. This will switch display between the number of recordable pictures and available recording time.
[REMAINING DISP.]
[REMAINING SHOTS]: This will display the number of recordable pictures for still pictures. [REMAINING TIME]: This will display the available recording time for motion pictures.
134
VQT3A48
Recording
[OFF]: [ON]:
Setting for not using the Touch Quick Menu. [ not displayed on the recording screen. The Touch Quick Menu can be used.
] is
[OFF]: [ON]:
Setting for not using the Touch Shutter function. [ is not displayed on the recording screen. The Touch Shutter function can be used.
[TOUCH GUIDE]
When playing back the pictures, this allows you to set either to display or not display the guide screen of the touch panel. [OFF]/[ON] This allows you to set the speed of continuously forwarding or rewinding pictures using touch operation. [H]: [L]: High speed Low speed
[TOUCH SCROLL]
[DIAL GUIDE]
Sets if the operation switch guide when the mode dial is switched to , , and is to be displayed or not. [OFF]/[ON]
perform Exposure Compensation, Programme Shift, aperture setting, or shutter speed setting when set to [ON]. A Dial operation guide
A The last operated menu position is saved even if the camera is turned off. [OFF]/[ON] It will perform optimization of imaging device and image processing.
[MENU RESUME]
[PIXEL REFRESH]
Imaging device and image processing is optimised when the camera is purchased. Use this Turn the camera off and on after the pixels are corrected.
function when bright spots not in subject get recorded, and it is bothering you.
VQT3A48
135
Recording
[SENSOR CLEANING]
Dust reduction to blow off the debris and dust that have affixed to the front of the imaging device is performed.
Dust reduction function will operate automatically when the camera is turned on, but you can
use this function when you see dust. (P178)
It is possible to setup so the shutter will not operate when there is no lens on the unit.
[SHOOT W/O LENS]
[OFF]:
You cannot press the shutter button when a lens is not attached to the camera body or is not attached correctly. Shutter will operate regardless of the lens on the unit.
[ON]:
When using a Leica lens mount adaptor (DMW-MA2M, DMW-MA3R; optional), set it to [ON].
136
VQT3A48
Playback/Editing
Playback/Editing
Continuous playback and multi playback in a group unit is possible. Deleting and editing in a group unit is possible. (For example, if you
delete a burst picture group with [], all the pictures in that group are deleted.) It is also possible to delete or edit single pictures within the group. Burst pictures recorded after the number of pictures has exceeded 50000 will not be grouped. Burst pictures recorded on other cameras may not be recognised as a burst picture group. Burst pictures will not be grouped if recorded without setting the clock.
Select a picture with a burst icon [], and then touch [ back.
Burst pictures are continuously played back. Pressing the cursor button 3 to allows you to playback burst pictures.
] to play
Display at the bottom right of the screen while playing back corresponds to 3/4/2/1 on the cursor button.
Touch [
It will resume normal playback once the continuous playback has finished. Operations during burst picture group playback Drag the screen horizontally and select an image.1
Forward: drag from right to left Rewind: drag from left to right Touch [ ] during playback to fast forward (touch [ ] to rewind). You can zoom while paused. Pause and rotate the rear dial left for multi playback of the pictures in the burst picture group. A Fast rewind, Previous picture2 B Play/Pause C Fast forward, Next picture2 D Stop 1 These operations can be performed only in the Pause Mode. 2 These operations can be performed only in the Pause Mode and the following icons are displayed. Previous picture: [ ] Next picture: [ ]
VQT3A48
137
Playback/Editing
To select an image during continuous playback of burst pictures (Burst Play menu)
1 2 3 4
Select an image during continuous playback, and pause by touching [ ]. Press [MENU/SET] to display the [PLAYBACK] Mode menu. Press 3/4 to select the item, and press 1. Press 3/4 to select [SINGLE] or [MULTI] and then press [MENU/SET]. You cannot select [SINGLE] or [MULTI] when [CROPPING] or Select the picture, and perform editing.
[ASPECT CONV.] is selected.
For details on the various ways of editing, refer to Using the [PLAYBACK] Mode Menu (P141). To select an image during normal playback
1 2
Select the item on the [PLAYBACK] mode menu and then press 1. (P55) Press 3/4 to select [SINGLE IN BURST GROUP] or [MULTI IN BURST GROUP] and then press [MENU/SET]. When [CROPPING] or [ASPECT CONV.] is selected, Only the burst picture groups with burst icon [] are displayed.
[MULTI IN BURST GROUP] will not appear.
3 4
Select the burst picture group and then press [MENU/SET]. Pictures within the group are displayed. Select the picture, and perform editing.
For details on the various ways of editing, refer to Using the [PLAYBACK] Mode Menu (P141).
138
VQT3A48
Playback/Editing
Editing in burst picture group units All pictures in the burst picture group are edited at once. For burst picture groups, the following editing menu can be used. [TITLE EDIT] (P144), [TEXT STAMP] (P145), [FAVORITE] (P150), [PRINT SET] (P151),
[PROTECT] (P152), [FACE REC EDIT] (P153)
1 2
Select the item on the [PLAYBACK] mode menu and then press 1. (P55) Press 3/4 to select [SINGLE] or [MULTI] and then press [MENU/SET]. Select an image with burst icon [] A, and perform editing. You can select multiple pictures from the burst picture group and
other images by selecting [MULTI] in step 2.
For details on the various ways of editing, refer to Using the [PLAYBACK] Mode Menu (P141).
About display of [FAVORITE], [PRINT SET] and [PROTECT] icons during playback of burst picture groups. If you set [FAVORITE] (P150), [PRINT SET] (P151) or [PROTECT] (P152) for any of the pictures in the burst picture group, the following icons will appear on the group top screen.
Initial screen for burst picture group [FAVORITE] [PRINT SET] [PROTECT]
A Total number of all pictures stored within the burst picture group. B Number of pictures in given burst picture group subject to a setting. C Total number of prints set over all burst picture groups. For example, if 3 pictures are to be printed from each of 2 burst pictures within the group, a "6" will appear here.
Note [CROPPING] and [ASPECT CONV.] is not possible at once on the burst picture group units. Pictures for which you have performed [TEXT STAMP], [CROPPING] or [ASPECT CONV.] will If you delete all pictures except one, that picture will be saved as a single picture instead of as
a burst picture group. be saved separately from burst pictures.
VQT3A48
139
Playback/Editing
Note It will be saved with [PICTURE SIZE] set to [S] (2 M), [ASPECT RATIO] set to [W], and Still pictures created from a motion picture may be coarser than with normal picture quality. Still pictures cannot be created from motion pictures recorded with [MOTION JPEG] set to [
or [ ]. You may not be able to save still pictures from a motion picture taken on other equipment. [ ] is displayed during playback of still pictures created from motion pictures. [QUALITY] set to []. ]
140
VQT3A48
Playback/Editing
[2D/3D SETTINGS]
Playback methods for the 3D pictures can be switched. This is a menu that is only displayed when 3D display is possible. Refer to P155 for details.
[SLIDE SHOW]
You can play back the pictures you have taken in synchronisation with music, and you can do this in sequence while leaving a fixed interval between each of the pictures. You can also put together a slide show composed of only still pictures, only motion pictures, only 3D pictures, only pictures of a particular category, or only favourites. We recommend this feature when you view your pictures by connecting the camera to a TV.
1 2
Select [SLIDE SHOW] on the [PLAYBACK] Mode menu. (P55) Press 3/4 to select the item and then press [MENU/SET]. [FAVORITE] can be selected only when [FAVORITE FUNC.] on
the [SETUP] menu (P62) is at [ON] and there are pictures already set as favourites. During [CATEGORY SELECTION], press 3/4/2/1 to select a category, and then press [MENU/SET] to proceed to step 3. For details on categories, refer to P143. Refer to P155 for the method to playback [3D] pictures in 3D.
3 4
Press 3 to select [START] and then press [MENU/SET]. Press 4 to finish the slide show. Normal Playback resumes after the slide show finishes.
Operations performed during slide show The cursor displayed during playback is the same as 3/4/2/1. The menu screen is restored when [] is pressed.
A B C D Play/Pause Stop Back to previous picture Ahead to next picture These operations can be performed only in the Pause Mode, during motion picture and burst picture group playback.
VQT3A48
141
Playback/Editing
Changing the slide show settings You can change the settings for slide show playback by selecting [EFFECT] or [SETUP] on the slide show menu screen. [EFFECT] This allows you to select the screen effects when switching from one picture to the next. [NATURAL], [SLOW], [SWING], [URBAN], [OFF], [AUTO] When [URBAN] has been selected, the picture may appear in black and white as a screen [AUTO] can be used only when [CATEGORY SELECTION] has been selected. The pictures [EFFECT] is fixed to [OFF] when in [VIDEO ONLY] or during the slide show for [
are played back with the recommended effects in each category. [CATEGORY SELECTION]. Even if [EFFECT] is set, it does not work during a slide show of burst picture group. Some [EFFECT] will not operate when playing back pictures displayed vertically. ] in effect.
[DURATION] can be set only when [OFF] has been selected as the [EFFECT] setting. Even if [DURATION] is set, it does not work during a slide show of motion pictures only or slide
show of burst picture group.
Note It is not possible to add new music. Audio is not played back even if set to [AUDIO] or [AUTO] during [VARIABLE MOVIE MODE]
playback.
142
VQT3A48
Playback/Editing
[PLAYBACK MODE]
Playback in [NORMAL PLAY], [PICTURE PLAY], [AVCHD PLAY], [MOTION JPEG PLAY], [3D PLAY], [CATEGORY PLAY] or [FAVORITE PLAY] can be selected.
1 2
Select [PLAYBACK MODE] on the [PLAYBACK] Mode menu. (P55) Press 3/4 to select the item and then press [MENU/SET]. [FAVORITE PLAY] can be selected only when [FAVORITE
FUNC.] on the [SETUP] menu (P62) is at [ON] and there are pictures already set as favourites. Refer to P155 for the method to playback [3D PLAY] pictures in 3D.
When [CATEGORY PLAY] is selected in step 2 Press 3/4/2/1 to select the category and then press [MENU/SET] to set. If a picture is found in a category, the category icon turns blue. It may take time to search the picture files if there are a lot on the If you press [] while searching, the searching will stop halfway. Pictures are sorted into the categories shown below.
[CATEGORY] Recording information e.g. Scene Modes [FACE RECOG.] [PORTRAIT], [i-PORTRAIT], [NIGHT PORTRAIT], [i-NIGHT PORTRAIT], [BABY1]/[BABY2], [i-BABY] [SCENERY], [i-SCENERY], [SUNSET], [i-SUNSET] [NIGHT PORTRAIT], [i-NIGHT PORTRAIT], [NIGHT SCENERY], [i-NIGHT SCENERY] [CATEGORY] Recording information e.g. Scene Modes [SPORTS], [PARTY] [BABY1]/[BABY2], [i-BABY] [PET] [FOOD] [TRAVEL DATE] Motion pictures card.
Press 3/4/2/1 to select the person to playback and then press [MENU/SET]. Face Recognition may not be possible or may not recognise faces correctly even for registered faces, depending on the facial expression and environment. Also, if there are multiple faces that are already registered in the picture, it will be categorized only once to the person found first in the registration.
VQT3A48
143
Playback/Editing
[TITLE EDIT]
You can add text (comments) to pictures. After text has been registered, it can be stamped in prints using [TEXT STAMP] (P145). (Only alphabetic characters and symbols can be entered.)
1 2
Select [TITLE EDIT] on the [PLAYBACK] Mode menu. (P55) Press 3/4 to select the item and then press [MENU/SET]. When [SINGLE IN BURST GROUP] or
[MULTI IN BURST GROUP] is selected, press 3/4/2/1 to select burst picture group, and press [MENU/SET] to proceed to step 3.
Select the picture, and then press [MENU/SET] to set. [] is displayed for pictures with titles
already registered.
[SINGLE]
[MULTI]
[MULTI] setting Press [DISPLAY] to set (repeat), and then press [MENU/SET] to set. The setting is cancelled when [DISPLAY] Press 2/1 to select Press 3/4/2/1 to is pressed again. the picture. select the pictures.
Enter the text. (P117) Press [] to return to the menu screen. (The menu screen is automatically restored when
[MULTI] is selected.)
Note To delete the title, erase all the text in the text input screen. Text can be scrolled if all of the registered text does not fit on the screen. You can print out texts (comments) using the PHOTOfunSTUDIO 6.0 BD Edition bundled You can set up to 100 pictures at one time with [MULTI]. You cannot use title edit for the following pictures. Motion pictures Pictures taken with [ ], [ ] or [ ] Pictures recorded with other equipment
software on the CD-ROM (supplied).
144
VQT3A48
Playback/Editing
[TEXT STAMP]
You can stamp the recording date/time, name, location, travel date or title onto the recorded pictures. It is suitable for regular size printing. (Pictures with a picture size larger than [S] will be resized when stamping the date etc. on them.)
1 2
Select [TEXT STAMP] on the [PLAYBACK] Mode menu. (P55) Press 3/4 to select the item and then press [MENU/SET]. When [SINGLE IN BURST GROUP] or
[MULTI IN BURST GROUP] is selected, press 3/4/2/1 to select burst picture group, and press [MENU/SET] to proceed to step 3.
Select the picture, and then press [MENU/SET] to set. [] appears on screen if the picture is
stamped with text.
[SINGLE]
[MULTI]
[MULTI] setting Press [DISPLAY] to set (repeat), and then press [MENU/SET] to set. The setting is cancelled when [DISPLAY] Press 2/1 to select Press 3/4/2/1 to is pressed again. the picture. select the pictures.
4 5
Press 3/4 to select text stamp items, and then press 1. Press 3/4 to select the settings, and then press [MENU/SET].
Item Setting item
Stamp the year, month and date. Stamp the year, month, day, hour and minutes.
Name registered in Face Recognition will be stamped. Stamps names on pictures that already have been registered name settings of [BABY1]/ [BABY2] or [PET] in Scene Mode. Stamps the travel destination name set under [LOCATION]. Stamps the travel date set under [TRAVEL DATE]. Title input in the [TITLE EDIT] will be stamped.
VQT3A48
[NAME]
[
[OFF]
[LOCATION]
[ON]: [OFF]
[TRAVEL DATE]
[TITLE]
145
Playback/Editing
6 7
], press 3 to select [YES] for stamping [AGE], and then press [MENU/SET] and proceed to step 7.
Press 3 to select [YES] and then press [MENU/SET]. Press [] to return to the menu screen. (The menu screen is automatically restored when
[MULTI] is selected.)
When you print pictures stamped with text, the date will be printed over the stamped text if you You can set up to 100 pictures at one time in [MULTI]. The picture quality may deteriorate when text stamping is carried out. Depending on the printer being used, some characters may be cut at printing. Check before Text and dates cannot be stamped on the pictures in the following cases. Motion pictures Pictures recorded without setting the clock and title Pictures that were previously stamped with [TEXT STAMP] Pictures taken with [ ], [ ] or [ ] Pictures recorded with other equipment
printing. specify printing of the date at the photo shop or on the printer.
Note
[VIDEO DIVIDE]
Recorded motion picture can be divided in two. It is recommended for when you want to divide a part you need with a part you do not need. It cannot be restored once divided.
1 2 3
Select [VIDEO DIVIDE] on the [PLAYBACK] Mode menu. (P55) Press 2/1 to select the motion picture to divide, and then press [MENU/SET]. Motion picture is played back. Press 3 at the location to divide. Motion picture is paused.
Motion picture is played back from the same location when 3 is pressed again. You can finely adjust the location for division by pressing 2/1 while the motion picture is paused.
4 5
Press 4. Press 2 to select [YES] and then press [MENU/SET]. Motion picture may be lost if the card or battery is removed while processing the dividing. Press [] to return to the menu screen.
Note Motion pictures cannot be divided at a location close to the start or end of the motion picture. [VIDEO DIVIDE] may not be performed on motion pictures recorded with other equipment. With [MOTION JPEG] motion pictures, the order of pictures will change if divided.
It is recommended to display these motion pictures by using Calendar Playback (P41) or [MOTION JPEG PLAY] in the [PLAYBACK MODE] (P143). With [AVCHD] motion pictures, the order of pictures will not change. Motion pictures cannot be divided in the following cases. Motion pictures with a short recording time
146
VQT3A48
Playback/Editing
1 2 3
Select [RESIZE] on the [PLAYBACK] Mode menu. (P55) Press 3/4 to select [SINGLE] or [MULTI] and then press [MENU/SET]. Select the picture and size. [SINGLE] setting 1 Press 2/1 to select the picture, and then press [MENU/SET]. 2 Press 2/1 to select the size, and then press [MENU/SET].
Only the sizes to which the pictures can be resized is displayed.
[SINGLE]
[MULTI] setting 1 Press 3/4 to select the size, and then press [MENU/SET]. 2 Press 3/4/2/1 to select the picture, and then press [DISPLAY]. Repeat this step for each picture,
and press [MENU/SET] to set.
[MULTI]
Press 3 to select [YES] and then press [MENU/SET]. Press [] to return to the menu screen. (The menu screen is automatically restored when
[MULTI] is selected.)
Note You can set up to 100 pictures at one time in [MULTI]. The picture quality of the resized picture will deteriorate. It may not be possible to resize pictures recorded with other equipment. Motion pictures, pictures stamped with [TEXT STAMP] and pictures taken with [
[ ] or [ ] cannot be resized.
],
VQT3A48
147
Playback/Editing
[CROPPING]
You can enlarge and then clip the important part of the recorded picture.
1 2
Select [CROPPING] on the [PLAYBACK] Mode menu. (P55) Press 3/4 to select [SINGLE] or [SINGLE IN BURST GROUP], and then press [MENU/SET]. When [SINGLE IN BURST GROUP] is selected, press 3/4/2/1 to select burst picture Press 2/1 to select the picture, and then press [MENU/SET]. Use the rear dial and press 3/4/2/1 to select the parts to be cropped. Rear dial (right): Enlargement Rear dial (left): Reduction
3/4/2/1: Move group, and press [MENU/SET] to proceed to step 3.
3 4
5 6
Press [MENU/SET]. Press 3 to select [YES] and then press [MENU/SET]. Press [] to return to the menu screen.
Note Depending on the cut size, the picture size of the cropped picture may become smaller than The picture quality of the cropped picture will deteriorate. It may not be possible to crop pictures recorded with other equipment. Motion pictures, pictures stamped with [TEXT STAMP] and pictures taken with [
that of the original picture.
], [ ] or [ ] cannot be cropped. Information regarding the Face Recognition in the original picture will not be copied to images having undergone [CROPPING].
? [ASPECT CONV.]
You can convert pictures taken with a [W] aspect ratio to a [Y], a [X] or a [ ratio. ] aspect
1 2 3 4 5 6
Select [ASPECT CONV.] on the [PLAYBACK] Mode menu. (P55) Press 3/4 to select [SINGLE] or [SINGLE IN BURST GROUP], and then press [MENU/SET]. Press 3/4 to select [Y], [X] or [ ] and then press [MENU/SET]. When [SINGLE IN BURST GROUP] is selected, press 3/4/2/1 to select burst picture Press 2/1 to select a picture taken with [W] aspect ratio, and then press [MENU/SET]. Press 2/1 to determine the horizontal position, and press [MENU/SET] to set. Use 3/4 to set the frame position for pictures rotated vertically. Press 3 to select [YES] and then press [MENU/SET]. Press [] to return to the menu screen.
group, and press [MENU/SET] to proceed to step 4.
148
VQT3A48
Playback/Editing
Note After converting the aspect ratio, the picture size may become larger than that of the original You may not be able to convert pictures taken on other equipment. The [ASPECT CONV.] cannot be performed on the motion pictures, pictures stamped with Information regarding the face recognition in the original picture will not be copied to images
having undergone [ASPECT CONV.]. [TEXT STAMP] and pictures taken with [ ], [ ] or [ ]. picture.
1 2 3
Select [ROTATE] on the [PLAYBACK] Mode menu. (P55) The [ROTATE] function is disabled when [ROTATE DISP.] is set to [OFF]. Press 2/1 to select the picture and then press [MENU/SET]. Press 3/4 to select the direction to rotate the picture and then press [MENU/SET]. : : The picture rotates clockwise in steps of 90o. The picture rotates counter-clockwise in steps of 90o.
Press [] to return to the menu screen. Rotate display (The picture is automatically rotated and displayed)
1 2
Select [ROTATE DISP.] on the [PLAYBACK] Mode menu. (P55) Press 4 to select [ON] and then press [MENU/SET]. The pictures are displayed without being rotated when you select [OFF].
Note [ROTATE DISP.] can only be used with the lens (P19) compatible with the Direction Detection When you play back pictures on a PC, they cannot be displayed in the rotated direction unless
the OS or software is compatible with Exif. Exif is a file format for still pictures which allows recording information etc. to be added. It was established by JEITA (Japan Electronics and Information Technology Industries Association). It may not be possible to rotate pictures that have been recorded with other equipment. The display is not rotated during Multi Playback (P40). Pictures recorded with the camera upside down will not be displayed rotated. Function (P36).
VQT3A48
149
Playback/Editing
[FAVORITE]
This can only be used when [FAVORITE FUNC.] (P62) in setup menu is set to [ON]. You can do the following if a mark has been added to pictures and they have been set as favourites. Play back the pictures set as favourites only as a slide show. Play back only the pictures set as favourites. ([FAVORITE PLAY]) Delete all the pictures not set as favourites. ([ALL DELETE EXCEPT]) For details about the icon display during Burst Picture Group playback, refer to P139.
1 2
Select [FAVORITE] on the [PLAYBACK] Mode menu. (P55) Press 3/4 to select the item and then press [MENU/SET]. When [SINGLE IN BURST GROUP] or
[MULTI IN BURST GROUP] is selected, press 3/4/2/1 to select burst picture group, and press [MENU/SET] to proceed to step 3. When [CANCEL] is selected, see Cancelling all the [FAVORITE] settings.
Select the picture, and then press [MENU/SET]. [] is displayed on pictures that are
already registered as favourites. When [MULTI] has been selected Repeat the above procedure. If [MENU/SET] is pressed again, the favourite setting is cancelled. Press [] to return to the menu screen.
[SINGLE]
[MULTI]
Press 2/1 to select Press 3/4/2/1 to the picture. select the pictures.
Cancelling all the [FAVORITE] settings 1 Select [CANCEL] on the screen shown in step 2 and then press [MENU/SET]. 2 Press 3 to select [YES] and then press [MENU/SET]. You cannot select [CANCEL] if not even one picture has been set as a favourite. [CANCEL] cannot be selected when in [PLAYBACK MODE]. Note You can set up to 999 pictures as favourites. When printing pictures at a photo printing store, [ALL DELETE EXCEPT] (P53) is useful so You may not be able to set pictures taken with other equipment as favourites. The pictures that were taken with the [QUALITY] set to [ ] cannot be set to [FAVORITE].
only the pictures you want to be printed remain on the card.
150
VQT3A48
Playback/Editing
[PRINT SET]
DPOF Digital Print Order Format is a system that allows the user to select which pictures to print, how many copies of each picture to print and whether or not to print the recording date on the pictures when using a DPOF compatible photo printer or photo printing store. For details, ask at your photo printing store. When you set [PRINT SET] for a burst picture group, the print setting for the number of prints will be applied to every picture in the group. For details about the icon display during Burst Picture Group playback, refer to P139.
1 2
Select [PRINT SET] on the [PLAYBACK] Mode menu. (P55) Press 3/4 to select the item and then press [MENU/SET]. When [SINGLE IN BURST GROUP] or
[MULTI IN BURST GROUP] is selected, press 3/4/2/1 to select burst picture group, and press [MENU/SET] to proceed to step 3. When [CANCEL] is selected, see Cancelling all the [PRINT SET] settings.
[SINGLE]
[MULTI]
Press 2/1 to select Press 3/4/2/1 to the picture. select the pictures.
Press 3/4 to set the number of prints, and then press [MENU/SET] to set. When [MULTI] has been selected repeat steps 3 and 4 for each picture. [999+] is displayed on the screen, if the total number of prints you set for a burst Press [] to return to the menu screen.
picture group is more than 1000 pictures.
Cancelling all the [PRINT SET] settings 1 Select [CANCEL] on the screen shown in step 2 and then press [MENU/SET]. 2 Press 3 to select [YES] and then press [MENU/SET]. You cannot select [CANCEL] if not even one picture has been set for printing. To print the date After setting the number of prints, set/cancel printing with the recording date by pressing [DISPLAY]. When you go to a photo printing store for digital printing, be sure to order the printing of the Depending on the photo printing store or the printer, the date may not be printed even if you set
to print the date. For further information, ask at your photo printing store or refer to the operating instructions for the printer. The date cannot be printed on pictures stamped with text. date additionally if required.
VQT3A48
151
Playback/Editing
Note The number of prints can be set from 0 to 999. With a printer supporting PictBridge, the date print settings of the printer may take precedence It may not be possible to use the print settings with other equipment. In this case, cancel all the If the file is not based on the DCF standard, the print setting cannot be set. [PRINT SET] cannot be set for motion pictures and pictures that were taken with the
[QUALITY] set to [ ]. settings, and reset the settings. so check if this is the case.
P [PROTECT]
You can set protection for pictures you do not want to be deleted by mistake. For details about the icon display during Burst Picture Group playback, refer to P139.
1 2
Select [PROTECT] on the [PLAYBACK] Mode menu. (P55) Press 3/4 to select the item and then press [MENU/SET]. When [SINGLE IN BURST GROUP] or
[MULTI IN BURST GROUP] is selected, press 3/4/2/1 to select burst picture group, and press [MENU/SET] to proceed to step 3. When [CANCEL] is selected, see Cancelling all the [PROTECT] settings.
Select the picture, and then press [MENU/SET]. Repeat these steps for each picture. The settings are cancelled when Press [] to return to the menu screen.
[MENU/SET] is pressed again. When [MULTI] has been selected
[SINGLE]
[MULTI]
Press 2/1 to select Press 3/4/2/1 to the picture. select the pictures. Cancelling all the [PROTECT] settings 1 Select [CANCEL] on the screen shown in step 2 and then press [MENU/SET]. 2 Press 3 to select [YES] and then press [MENU/SET]. If you press [MENU/SET] while cancelling protection, the cancelling will stop halfway. Note The protect setting may not be effective on other equipment. Even if you protect pictures on a card, they will be deleted if the card is formatted. Even if you do not protect pictures on a card, they cannot be deleted when the cards
Write-Protect switch is set to [LOCK].
152
VQT3A48
Playback/Editing
1 2 3 4
Select [FACE REC EDIT] on the [PLAYBACK] Mode menu. (P55) Press 3/4 to select [REPLACE] or [DELETE] and then press [MENU/SET]. Press 2/1 to select the picture and then press [MENU/SET]. You cannot select pictures for which Face Recognition information has not been
registered.
5 6
Press 2/1 to select the person and then press [MENU/SET]. [DELETE] > step 6. You cannot select a person who has not been registered. Press 3/4/2/1 to select the person to replace and then press [MENU/SET]. Press 3 to select [YES] and then press [MENU/SET]. Press [] to return to the menu screen.
Note Cleared information regarding the [FACE RECOG.] cannot be restored. When all Face Recognition information in a picture has been cancelled, the picture will not be
categorised using Face Recognition in [CATEGORY PLAY].
VQT3A48
153
Enjoying 3D pictures
Taking 3D pictures Attaching the 3D interchangeable lens (H-FT012; optional) to the camera allows you to take 3D pictures for extra impact. To view 3D pictures, a television that supports 3D is required. 3D picture
Attach the 3D interchangeable lens to the camera. (P21) Bring the subject into the frame and record by pressing the shutter button fully.
Focusing is not required when recording 3D pictures. Still pictures recorded with the 3D interchangeable lens attached are saved in MPO format (3D). To ensure that the 3D pictures can be safely viewed, pay attention to the following points when recording. Where possible, record with the unit in a horizontal state. Do not get too close to the subject [when the 3D interchangeable lens (H-FT012; optional) is Be careful not to shake the camera while in a vehicle or walking. Note You cannot record 3D pictures in vertical orientation. It is recommended to use a tripod or a flash to record steady pictures. When a distance to the subject is 0.6 m (1.97 feet) to approximately 1 m (3.28 feet), horizontal Up to approx. 460 3D pictures can be recorded on a 2 GB card. (When the aspect ratio is set to Read the operating instructions of the 3D interchangeable lens for details. Functions that cannot be used during 3D recording When recording with the 3D interchangeable lens (H-FT012; optional), the following feature will be disabled: (Recording functions) Auto Focus/Manual Focus operation Aperture setting Zoom operation Recording motion pictures1 [DYNAMIC ART] in My Colour Mode Monitor output (P159)
[X], and the quality is set to [ ].) disparity becomes too great, and you may not see the 3D effect at the edges of the image. used, record from a distance of at least 0.6 m (1.97 feet)].
1 The motion picture button, Creative Motion Picture Mode and the [MOTION PICTURE] Mode menu will be unavailable or unusable.
154
VQT3A48
Picture size
1920k1440 pixels 1920k1280 pixels 1920k1080 pixels 1792k1792 pixels
[ [
]: MPOiFine (Both MPO images and fine JPEG images are recorded simultaneously.) ]: MPOiStandard (Both MPO images and standard JPEG images are recorded simultaneously.)
REC AREA]/
Playing back 3D pictures Connecting the camera to a 3D compatible television and playing back pictures taken in 3D allows you to enjoy 3D pictures for extra impact. It is also possible to playback the recorded 3D pictures by inserting an SD card into the 3D compatible television with an SD card slot. For the latest information on 3D compatible televisions and recorders that are capable of playing back 3D pictures recorded using the unit, see the support site below. http://panasonic.jp/support/global/cs/dsc/ (This Site is English only.) Preparations: Set the [HDMI MODE] to [AUTO] or [1080i]. (P61) Set the [3D PLAYBACK] to [ ]. (P61)
Connect the unit to a 3D compatible television using the HDMI mini cable and display the playback screen. (P158)
When [VIERA Link] (P61) is set to [ON] and the camera is connected to a TV supporting VIERA
Link, input of the TV will be switched automatically and playback screen will be displayed. Refer to P159 for details. For the pictures recorded in 3D, [ ] will appear on the thumbnail display at playback.
Playback in 3D by selecting only the still pictures recorded in 3D Select [3D PLAY] in [PLAYBACK MODE] in the [PLAYBACK] Mode menu. (P143) Playback as a 3D slide show by selecting only the still pictures recorded in 3D Select [3D] in [SLIDE SHOW] in the [PLAYBACK] Mode menu. (P141)
VQT3A48
155
Switch the playback method for the still pictures recorded in 3D 1 Select the picture recorded in 3D. 2 Select [2D/3D SETTINGS] on the [PLAYBACK] Mode menu and then press 1. (P55) Playback method will switch to 3D if it is playing back in 2D (conventional image), or it will If you feel tired, uncomfortable or otherwise strange when playing back pictures recorded
in 3D, set to 2D. switch to 2D if it is playing back in 3D.
Functions that cannot be set/do not work with 3D pictures [HIGHLIGHT] in the [CUSTOM] menu Playback Zoom Deleting pictures Editing functions of [PLAYBACK] Mode menu ([TITLE EDIT]/[TEXT STAMP]/[VIDEO DIVIDE]/
[RESIZE]/[CROPPING]/[ASPECT CONV.]/[ROTATE]/[ROTATE DISP.]/[FAVORITE]/ [PRINT SET]/[PROTECT]/[FACE REC EDIT]) Can be used when displayed in 2D.
Note When a picture recorded in 3D is displayed on the LCD monitor/viewfinder of this unit, it is A black screen is displayed for a few seconds when switching back and forth playback of 3D When you select a 3D picture thumbnail, it may take a few seconds for playback to start. After When viewing 3D pictures, your eyes may become tired if you are too close to the television If your television does not switch to a 3D picture, make the necessary settings on the TV. (For
details, refer to the operating instructions of the TV.) screen. playback, the thumbnail display may take a few seconds to reappear. pictures and 2D pictures. played back in 2D (conventional image).
Saving 3D pictures You can save 3D pictures using a recorder or a computer. Dubbing with a recorder 3D pictures will be recorded in MPO format when copied with the 3D compatible recorder. When the copied pictures do not playback in 3D, perform the necessary setup on the television. Note that the equipment described may not be available in certain countries and
regions. (For details, refer to the operating instruction of the television.)
Copying of the still pictures recorded in 3D Check the latest information about the equipment that can copy on the following website. http://panasonic.jp/support/global/cs/dsc/ (This Site is English only.) Copying to a PC For details, refer to Copying to a PC using PHOTOfunSTUDIO 6.0 BD Edition on P163.
156
VQT3A48
1 Yellow: to the video input socket 2 White: to the audio input socket 3 Red: to the audio input socket
A Align the marks, and insert. B AV cable (supplied) Check the directions of the connectors, and plug them straight in or unplug them straight out. (Otherwise the connectors may be bent out of shape which may cause malfunction.)
Connect the AV cable B (supplied) to the video input and the audio input sockets on the TV. Connect the AV cable to the [AV OUT] socket on the camera. Turn the TV on and select external input. Turn the camera on and then press [(].
Note Depending on the [ASPECT RATIO], black bands may be displayed on the top and bottom or Do not use any other AV cables except the supplied one. Read the operating instructions for the TV. When you play back a picture vertically, it may be blurry. You can view pictures on TVs in other countries (regions) which use the NTSC or PAL system Audio will be played back as stereo (2ch). The viewfinder cannot be displayed when connected with a AV cable. Change the screen mode on your TV if the picture is displayed with the top or bottom cut off. AV output is disabled when recording.
when you set [VIDEO OUT] in the [SETUP] menu. the left and right of the pictures.
VQT3A48
157
Playing back pictures on a TV with an SD Memory Card slot The recorded still pictures can be played back on a TV with an SD Memory Card slot. Note Depending on the TV model, pictures may not be displayed on the full screen. Motion pictures recorded with [AVCHD] can be played back on Panasonic TVs (VIERA) with
the AVCHD logo mark. In all other cases, connect the camera to the TV using the AV cable (supplied) and play back the motion picture. SDHC Memory Cards cannot be played back unless it is a TV compatible with SDHC Memory Cards or SDXC Memory Cards. SDXC Memory Cards cannot be played back unless it is a TV compatible with SDXC Memory Cards.
Playing back on the TV with HDMI socket You can enjoy high quality pictures and motion pictures on the TV by connecting the camera with the HDMI compatible high-definition TV using HDMI mini cable (optional). Preparations: Check the [HDMI MODE]. (P61) Turn this unit and the TV off.
HDMI IN
1 HDMI socket 2 TV with HDMI socket 3 HDMI mini (C type) A Align the marks, and insert. B HDMI mini cable (optional) Check the direction of the terminals and plug in/out straight holding onto the plug. (It may result
in malfunction if it is plugged in obliquely or in the wrong direction.)
Connect the HDMI mini cable B (optional) to the HDMI input socket on the TV. Connect the HDMI mini cable to the [HDMI] socket on the camera. Turn the TV on and switch to HDMI input. Turn the camera on and then press [(].
When [VIERA Link] (P61) is set to [ON] and the camera is connected to a TV supporting
VIERA Link, input of the TV will be switched automatically and playback screen will be displayed (P159).
158
VQT3A48
Note Depending on the [ASPECT RATIO], bands may be displayed on the top and bottom or the left Always use a genuine Panasonic HDMI mini cable (RP-CDHM15, RP-CDHM30; optional). Output from the HDMI mini cable has priority when both AV cable and HDMI mini cable are The connection with the USB connection cable will take priority when you connect the USB When pictures are displayed, they may not be displayed properly depending on the type of TV. Read the operating instructions for the TV. Audio will be played back as stereo (2ch). During [24P CINEMA] and [VARIABLE MOVIE MODE] playback, please set [HDMI MODE] to
[AUTO]. For settings other than [AUTO], it cannot output at 24 frames/second. connection cable simultaneously with the HDMI mini cable. connected. Part numbers: RP-CDHM15 (1.5 m) (5 feet), RP-CDHM30 (3.0 m) (10 feet) and right of the pictures.
Monitoring camera images on the TV With HDMI output, you can monitor full high-definition quality (1920k1080 pixels) AVCHD motion pictures on the TV while recording. Note Some functions are unavailable during monitoring. Audio is not output from the TV. Up to 20 still pictures can be recorded during recording of the motion picture. Playback using VIERA Link (HDMI) (HDAVI Control) What is the VIERA Link? This function allows you to use your remote control for the Panasonic TV for easy
operations when this unit has been connected to a VIERA Link compatible device using a HDMI mini cable (optional) for automatic linked operations. (Not all operations are possible.) VIERA Link is a unique Panasonic function built on a HDMI control function using the standard HDMI CEC (Consumer Electronics Control) specification. Linked operations with HDMI CEC compatible devices made by other companies are not guaranteed. When using devices made by other companies that are compatible with VIERA Link, refer to the operating instructions for the respective devices. This unit is compatible with VIERA Link Ver.5. VIERA Link Ver.5 is the newest Panasonic version and is also compatible with existing Panasonic VIERA Link devices. (As of December 2009)
1 2 3
Connect this unit to a Panasonic TV compatible with VIERA Link with a HDMI mini cable (optional) (P158). Turn the camera on and then press [(]. Operate with the remote control for the TV.
VQT3A48
159
The shape of the remote control varies depending on the region. Operate following the TV guide displayed on screen.
Usable functions Operate with the remote control for the TV. This is displayed initially when using the VIERA Link. 3/4/2/1: Select the image. [OK]: Go to one screen display. Pictures in Burst Picture Group are played back with Multi Playback. (When Burst Picture Group is selected) Red button: Switch the types of data to play back. [OPTION]: Display the Playback Mode selection screen. The type of data for playback changes in the order of [ALL] > [ ]>[ ]>[ ]>[ ] > [ALL]. Either the [NORMAL PLAY], [SLIDE SHOW], [CATEGORY
PLAY], [FAVORITE PLAY] or the [CALENDAR] can be selected in the Playback Mode selection screen when [ALL] is selected.
Multi Playback
Select the image while in Multi Playback, and then press [OK]. 2/1: Go to previous/next image. 3: 2D/3D switch1 4: Return to Multi Playback. [OK]: Playback the motion picture (when motion picture is selected). Playback burst pictures (when burst picture is selected). Red button: Start the Slide Show. [OPTION]: Slide show settings2, display the recording information switch During Motion Picture Playback/Burst Picture Playback, 2/1
will fast rewind/fast forward, and 4 will end the playback.
160
VQT3A48
Slide show
Press Red button during one screen display. 2/1: Go to previous/next image (when Slide Show is paused/when motion picture is played back). 4: Finish the Slide Show and return to one screen display. [OK]: Pause. [OPTION]: Go to Slide Show setting screen.2 To playback the audio of the motion pictures, set the [SOUND] in
the Slide Show setting screen to [AUTO] or [AUDIO].
A Operation icon 1 This is displayed only when 3D playback is possible. 2 This is not displayed during 3D playback.
Note Operation icons are hidden by pressing [RETURN], or if no operation is performed for a while
when the operation icons are displayed. Operation icons are displayed when one of the following buttons is pressed while the operation icons are not displayed. 3/4/2/1, [OK], [OPTION], [RETURN], Red button, Green button, Yellow button It is recommended to connect this unit to an HDMI terminal other than the HDMI1 if there are 2 or more HDMI input terminals on the TV. When the [VIERA Link] (P61) of this unit is set to [ON], operation using the button on this unit will be limited. VIERA Link must be activated on the connected TV. (Read the operating instructions of the TV for how to set etc.) If you are not using VIERA Link, set [VIERA Link] (P61) to [OFF].
Other linked operations Turning the power off: If you use the remote control for the TV to turn off the power, the power on this unit also turns off. Automatic input switching: If you connect with a HDMI mini cable and then turn on the power on this unit, and then press
[(], the input channel on the TV automatically switches to this units screen. If the TVs power is in standby status, it will turn on automatically (if [Set] has been selected for the TVs [Power on link] setting). Depending on the HDMI terminal on the TV, the input channel may not switch automatically. In this case, use the remote control for the TV to switch the input channel. (For details on how to switch input, please read the operating instructions for the TV.) If VIERA Link does not work properly, refer to page 192.
Note If you are unsure whether or not the TV you are using are compatible with VIERA Link, read the Available linked operations between this unit and a Panasonic TV is different depending on the
operating instructions for the TV. types of Panasonic TVs even if they are compatible with VIERA Link. Refer to the operating instructions of the TV for the operations that support on the TV. Operation is not possible with a cable that is not based on the HDMI standard. Always use a genuine Panasonic HDMI mini cable (RP-CDHM15, RP-CDHM30; optional). Part numbers: RP-CDHM15 (1.5 m) (5 feet), RP-CDHM30 (3.0 m) (10 feet) VIERA Link will not work even if you connect the HDMI mini cable while the unit is connected to the PC or the printer. [HDMI MODE] (P61) for this unit is determined automatically when the VIERA Link is operating.
VQT3A48
161
Copy the playback image using an AV cable File formats that can be used: [AVCHD], [Motion JPEG] Copy images played back with this unit to Blu-ray disk, DVD disc, hard disk, or video using a Blu-ray Disk Recorder, DVD recorder, or video. This can be played back with equipment that is not compatible with high-definition (AVCHD), so it is convenient for distributing copies. Image will be standard quality instead of high-definition at this time. 1 2 3 A Yellow: to the video input socket White: to the audio input socket Red: to the audio input socket AV cable (supplied)
1 2 3
Connect this unit with the recording equipment with an AV cable (supplied). Start the playback of this unit. Start the recording on the recording equipment. When ending the recording (copying), stop the playback on this unit after stopping the
recording in recording equipment.
162
VQT3A48
Note When you play back motion pictures on 4:3 aspect ratio TV, you must set [TV ASPECT] (P60)
on this unit to [4:3] before starting a copy. The image will be vertically long if you play back motion pictures copied with [16:9] setting on a [4:3] aspect TV. Do not use any other AV cables except the supplied one. It is recommended to turn off the display of the screen by pressing the [DISPLAY] on the camera while copying. (P40) See the instruction manual for the recording equipment about the details of copying and playing back.
Copying to a PC using PHOTOfunSTUDIO 6.0 BD Edition File formats that can be used: [JPEG], [RAW], [MPO], [AVCHD], [Motion JPEG] It is possible to acquire still pictures and motion pictures recorded in [AVCHD] or [MOTION JPEG] formats, or create conventional standard quality DVD video from the motion picture that was recorded as [AVCHD], using PHOTOfunSTUDIO 6.0 BD Edition in the CD-ROM (supplied). Also, you can write images to DVD, combine multiple pictures to create a single panorama picture, or create a slide show by adding audio and/or music. These pictures can then be stored onto a DVD.
1 2 3
Install PHOTOfunSTUDIO 6.0 BD Edition to the PC. Read the separate operating instructions for the supplied software for more information Connect camera to PC. For details on connecting, refer to Connecting to a PC (P164). Copy the images to a PC using PHOTOfunSTUDIO 6.0 BD Edition. For details, refer to the operating instructions of PHOTOfunSTUDIO 6.0 BD Edition
(PDF). about the software in the CD-ROM (supplied) and how to install it.
Note You will not be able to playback the acquired [AVCHD] motion pictures when the files or folders
related to the motion pictures are deleted, modified, or moved using Windows Explorer or similar, so make sure to acquire the [AVCHD] motion pictures using PHOTOfunSTUDIO 6.0 BD Edition.
VQT3A48
163
Connecting to a PC
You can acquire recorded pictures to a PC by connecting the camera and the PC. Some PCs can read directly from the card removed from the camera. For details, refer to the If the computer being used does not support SDXC Memory Cards, a message
operating instructions of your PC. prompting you to format may appear. (Doing so will cause recorded images to be erased so do not choose to format.) If the card is not recognised, please refer to the below support site. http://panasonic.net/avc/sdcard/information/SDXC.html You can easily print out or mail the pictures you have imported. Use of the PHOTOfunSTUDIO 6.0 BD Edition bundled software on the CD-ROM (supplied) is a convenient way of doing this. Read the separate operating instructions for the supplied software for more information about the software in the CD-ROM (supplied) and how to install it.
Acquiring of still pictures and [MOTION JPEG] motion pictures (other than [AVCHD] motion pictures) Preparations: Turn the LCD monitor so the LCD will show out. Turn on the camera and the PC.
A USB connection cable (supplied) Check the directions of the connectors, and plug them straight in or unplug them straight out. (Otherwise the connectors may be bent out of shape which may cause malfunction.) B Align the marks, and insert. Use a battery with sufficient battery power or the AC adaptor (DMW-AC8E; optional) and DC coupler (DMW-DCC8; optional). If the remaining battery power becomes low while the camera and the PC are communicating, the status indicator blinks and the alarm beeps. Refer to Disconnecting the USB connection cable safely (P165) before disconnecting the USB connection cable. Otherwise, data may be destroyed.
164
VQT3A48
USB MODE
advance, the camera will be automatically connected to the PC SELECT SET without displaying the [USB MODE] selection screen. Since there is no need to set this each time you connect to the PC, it is convenient. When the camera has been connected to the PC with [USB MODE] set to [PictBridge(PTP)], a message may appear on the PCs screen. Select [Cancel] to close the screen, and disconnect the camera from the PC. Then set [USB MODE] to [PC] again.
MENU
Double-click [DCIM] folder. Using a drag-and-drop operation, move the pictures you want to acquire or the folder storing those pictures to any different folder on the PC.
Data from the PC can not be written to the camera using the USB connection cable. Disconnecting the USB connection cable safely Proceed with the hardware removal using Safely Remove Hardware on the task tray of the
PC. If the icon is not displayed, check that [ACCESS] is not displayed on the LCD monitor of the digital camera before removing the hardware.
Note Turn the camera off before connecting or disconnecting the AC adaptor (DMW-AC8E; Before inserting or removing a card, turn the camera off and disconnect the USB connection
cable. Otherwise, data may be destroyed. optional).
VQT3A48
165
Viewing the contents of the card using the PC (folder composition) Folders and images processed in the PC cannot be played back on the camera. It is recommended to use the PHOTOfunSTUDIO 6.0 BD Edition bundled software on the CD-ROM (supplied) when you write the image from PC to a card. Folder number Colour space P: sRGB _: AdobeRGB 3 File number 4 JPG: Pictures MOV: [MOTION JPEG] RW2: Pictures in RAW files MPO: 3D pictures MISC: DPOF print Favourite AVCHD: [AVCHD] Motion pictures 1 2
A new folder is created when pictures are taken in the following situations. After [NO.RESET] (P63) in the [SETUP] menu has been executed When a card containing a folder with the same folder number has been inserted (Such as when When there is a picture with file number 999 inside the folder Connection in the PTP Mode (WindowsR XP, Windows VistaR, WindowsR 7 and Mac OS X only) Set [USB MODE] to [PictBridge(PTP)]. Data can now be read only from the card into the PC. When there are 1000 or more pictures on a card, the pictures may not be imported in the PTP [AVCHD] motion picture cannot be played back in PTP Mode.
mode. pictures were taken using another make of camera)
166
VQT3A48
Preparations: Turn on the camera and the printer. Perform the print quality and other settings at the printer before printing the pictures.
A USB connection cable (supplied) Check the directions of the connectors, and plug them straight in or unplug them straight out. (Otherwise the connectors may be bent out of shape which may cause malfunction.) B Align the marks, and insert. Use a battery with sufficient battery power or the AC adaptor (DMW-AC8E; optional) and DC coupler (DMW-DCC8; optional). If the remaining battery power becomes low while the camera and the printer are connected, the status indicator blinks and the alarm beeps. If this happens during printing, stop printing at once. If not printing, disconnect the USB connection cable.
Connect the camera to a printer via the USB connection cable A (supplied).
When the camera is connected to the printer, the cable disconnect prohibit icon []
appears. Do not disconnect the USB cable while [] is displayed.
USB MODE
SELECT
SET
MENU
Note Do not use any other USB connection cables except the supplied one. Use of cables other than Turn the camera off before connecting or disconnecting the AC adaptor (DMW-AC8E; Before inserting or removing a card, turn the camera off, and disconnect the USB connection Motion pictures recorded cannot be printed out.
cable. optional). the supplied USB connection cable may cause malfunction.
VQT3A48
167
Press 2/1 to select the picture and then press [MENU/SET]. The message disappears in about 2 seconds.
PictBridge
100_0001
MENU
Press 3 to select [PRINT START] and then press [MENU/SET]. Refer to P169 for the items which can be set before starting to print Press [MENU/SET] to cancel printing halfway. Disconnect the USB connection cable after printing. Selecting multiple pictures and printing them
the pictures.
SINGLE SELECT PRINT START PRINT WITH DATE NUM. OF PRINTS PAPER SIZE PAGE LAYOUT
OFF 1
CANCEL
SELECT SET
MENU
1 2
Press 3. Press 3/4 to select an item and then press [MENU/SET]. If the print check screen has appeared, select [YES], and print the
pictures.
PictBridge MULTI SELECT SELECT ALL PRINT SET (DPOF) FAVORITE
CANCEL SELECT
SET
MENU
Item
Description of settings Multiple pictures are printed at one time. Press 3/4/2/1 to select the pictures, and then when [DISPLAY] is pressed, [] appears on the pictures to be printed. (When [DISPLAY] is pressed again, the setting is cancelled.) After the pictures have been selected, press [MENU/SET]. Prints all the stored pictures. Prints the pictures set in [PRINT SET] only. (P151) Prints the pictures set as favourites only. (P150)
[MULTI SELECT]
Only when [FAVORITE FUNC.] is at [ON] and when there are pictures set as favourites. (P150)
Press 3 to select [PRINT START] and then press [MENU/SET]. Refer to P169 for the items which can be set before starting to print Press [MENU/SET] to cancel printing. Disconnect the USB connection cable after printing.
the pictures.
MULTI SELECT PRINT START PRINT WITH DATE NUM. OF PRINTS PAPER SIZE PAGE LAYOUT
OFF 1
CANCEL
SELECT SET
MENU
168
VQT3A48
Print Settings Select and set the items both on the screen in step 2 of the Selecting a single picture and printing it and in step 3 of the Selecting multiple pictures and printing them procedures. When you want to print pictures on a paper size or a layout which is not supported by the
camera, set [PAPER SIZE] or [PAGE LAYOUT] to [{] and then set the paper size or the layout on the printer. (For details, refer to the operating instructions of the printer.) When [PRINT SET (DPOF)] has been selected, the [PRINT WITH DATE] and [NUM. OF PRINTS] items are not displayed.
If the printer does not support date printing, the date cannot be printed on the picture. Since the printers settings may take precedence over the print with date setting, check the When printing images with a text stamp, please remember to set print with date to [OFF] or the In some printers, the picture date for pictures taken with the aspect ratio set to [
printed vertically. date will print on top. ] will be printers print with date setting as well.
Note
When asking the photo shop to print the pictures By stamping the date using [TEXT STAMP] (P145) or setting date printing at the time of the [PRINT SET] (P151) setting before going to a photo shop, the dates can be printed at the photo shop.
[NUM. OF PRINTS] You can set the number of prints up to 999. You can also use the rear dial to set.
VQT3A48
169
[PAPER SIZE]
Item { [L/3.5qk5q] [2L/5qk7q] [POSTCARD] [16:9] [A4] [A3] [10k15cm] [4qk6q] [8qk10q] [LETTER] [CARD SIZE] 89 mmk127 mm 127 mmk178 mm 100 mmk148 mm 101.6 mmk180.6 mm 210 mmk297 mm 297 mmk420 mm 100 mmk150 mm 101.6 mmk152.4 mm 203.2 mmk254 mm 216 mmk279.4 mm 54 mmk85.6 mm Description of settings Settings on the printer are prioritised.
Paper sizes not supported by the printer will not be displayed. [PAGE LAYOUT] (Layouts for printing that can be set with this unit)
Item { Description of settings Settings on the printer are prioritised. 1 picture with no frame on 1 page 1 picture with a frame on 1 page 2 pictures on 1 page 4 pictures on 1 page
An item cannot be selected if the printer does not support the page layout. Layout printing When printing a picture several times on 1 sheet of paper For example, if you want to print the same picture 4 times on 1 sheet of paper, set [PAGE LAYOUT] to [] and then set [NUM. OF PRINTS] to 4 for the picture that you want to print. When printing different pictures on 1 sheet of paper For example, if you want to print 4 different pictures on 1 sheet of paper, set [PAGE LAYOUT] to [] and then set [NUM. OF PRINTS] to 1 for each of the 4 pictures. Note The camera is receiving an error message from the printer when the [] indication lights
orange during printing. After finishing printing, make sure there are no problems with the printer. If the number of prints is high, the pictures may be printed several times. In this case, the remaining number of prints indicated may differ from the number set. When the pictures in RAW files are to be printed, the JPEG pictures recorded simultaneously by the camera will be printed. If JPEG pictures do not exist, RAW file pictures cannot be printed.
VQT3A48
170
Others
Others
Optional accessories
External Flash (optional) After attaching the external flash (DMW-FL220, DMW-FL360, DMW-FL500; optional), the effective range will be increased when compared to the cameras built in flash. Preparations: Turn off the camera and close the built-in flash. Using the dedicated flash (DMW-FL220; optional)
Attach the dedicated flash to the hot shoe and then turn on the camera and the dedicated flash. Select [FLASH] on the [REC] Mode menu. (P55) Press 3/4 to select the mode and then press [MENU/SET].
While the external flash is connected, the following icons are displayed. : External flash Forced ON : External flash Slow Sync. When using other commercially available external flashes without communication functions with the camera (DMC-GH2) It is necessary to set the exposure on the external flash. If you want to use the external flash in
Auto Mode, use an external flash that allows you to set the aperture value and the ISO sensitivity to match the settings on the camera. Set to Aperture-Priority AE Mode or Manual Exposure Mode on the camera and then set the same aperture value and ISO sensitivity on the external flash. (The exposure cannot be compensated adequately due to the change on the aperture value in Shutter-Priority AE Mode and the external flash cannot control the light adequately in Programme AE Mode because the aperture value cannot be fixed.)
Note You can set the aperture value, the shutter speed and the ISO sensitivity on the camera even Some commercial external flashes have synchro terminals with high-voltage or reversed
when attaching the external flash. polarity. Using such extra flashes may cause a malfunction or the camera may not operate normally. If you use commercially available external flashes with communication functions other than the dedicated one, they may not operate normally or they may be damaged. Do not use them. Even if the external flash is turned off, the camera may enter the external flash mode when the external flash is attached. When you are not using the external flash, detach it. Do not open the built-in flash when an external flash is attached. The camera will become unstable when attaching the external flash, it is recommended to use a tripod when taking picture. Detach the external flash when carrying the camera. When attaching the external flash, do not hold only the external flash because it may detach from the camera.
VQT3A48
171
Others
If you use the external flash when the White Balance is set to [
] finely adjust the White Balance depending on the picture quality. (P90) If you take pictures close to the subject in Wide, the vignetting effect may appear on the bottom of the recorded picture. The external flash cannot be used while the stereo microphone (DMW-MS1; optional) is in use. Read the operating instructions of the external flash for details.
Protector/Filter (optional) The MC protector (optional) is a transparent filter which affects neither the colours nor the amount of light, so it can always be used to protect the cameras lens. The ND filter (optional) reduces the amount of light to approximately 1/8th (equal to adjusting the aperture value 3 increments) without affecting the colour balance. PL filter (optional) will suppress the reflected light from a metal or non spherical surfaces (flat non-metallic surfaces, water vapour or invisible particles in the air), making it possible to take a picture with enhanced contrast. Note MCuMulti-coated NDuNeutral Density Do not attach multiple filters at the same time. You can attach the lens cap or the lens hood when the filter is attached. Accessories other than filters, such as conversion lenses, cannot be mounted. It may cause
malfunction.
(DMW-LND62; optional), or the PL filter (DMW-LPL62; optional) with the lenses supplied in DMC-GH2H. It is recommended to use the MC protector (DMW-LMC52; optional), the ND filter (DMW-LND52; optional), or the PL filter (DMW-LPL52; optional) with the lens supplied in DMC-GH2K. Refer to the instructions for each filter for details.
Remote Shutter (optional) If you use the remote shutter (DMW-RSL1; optional), you can avoid jitter (camera shake) when using a tripod and you can keep the shutter pressed fully when taking pictures with [B] (Bulb) or Burst Mode. The remote shutter works similar to the shutter button on the camera. Note Always use a genuine Panasonic remote shutter (DMW-RSL1; optional). You cannot operate the camera with the remote shutter in the following cases. When the Sleep Mode is cancelled Record with Creative Motion Picture Mode (P106) when using for motion picture recording. The remote shutter cannot be used while the stereo microphone (DMW-MS1; optional) is in Read the operating instructions of the remote shutter for details.
use. Motion picture recording can be started/stopped with the remote shutter.
172
VQT3A48
Others
External Microphone (optional) If you use the stereo microphone (DMW-MS1; optional), you can switch to either stereo or monaural sound recording. It is also possible to reduce the wind noise efficiently by switching the [WIND CUT OFF/ ON] switch to [ON]. Battery Check Lamp [BATTERY] When the Off/On Mode Selector Switch is changed from [OFF] to [MONO] or [STEREO], the
Battery Check Lamp [BATTERY] will light temporarily if there is still plenty of power in the battery. If the Battery Check Lamp [BATTERY] does not light temporarily, replace the battery with a new one.
Note While the external microphone is connected, [ ] is displayed on the screen. When the external microphone is connected, [MIC LEVEL DISP.] (P129) is automatically set to When attaching the stereo microphone, do not hold only the stereo microphone because it may Set the wind noise reduction only on the stereo microphone side. Do not open the built-in flash when the stereo microphone is attached. The stereo microphone cannot be used while the external flash (optional) is in use. The stereo microphone cannot be used while the remote shutter (DMW-RSL1; optional) is in Read the operating instructions of the stereo microphone for details. AC adaptor (optional)/DC coupler (optional) By connecting the AC adaptor (DMW-AC8E; optional) and the DC coupler (DMW-DCC8; optional), and then plugging them into an electrical socket, you can connect this unit to a PC or printer and use without worrying about the capacity of the battery. Note Always use a genuine Panasonic AC adaptor (DMW-AC8E; optional). Always use a genuine Panasonic DC coupler (DMW-DCC8; optional). When using an AC adaptor, use the AC mains lead supplied with the AC adaptor. Also read the operating instructions for the AC adaptor and DC coupler.
use. detach from the camera. [ON], and the mic level is displayed on the screen.
VQT3A48
173
Others
] (Initial setting)
1 2
STD.
5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28
Flash Mode (P69) Film Mode (P118) Optical Image Stabilizer (P74)/ : Jitter alert (P75) : Single1 (P35) : Burst (P77) : Auto Bracket (P79) : Self-timer (P81) REC MODE (when recording motion pictures) (P127)/Recording quality (P127) Picture size (P120) Quality (P121) Intelligent Dynamic Range Control (P124) Intelligent Resolution (P123) Battery indication (P26) Card (P29) (displayed only during recording) Recording state (Flashes red.)/ Focus (P34) (Lights green.) Touch Quick Menu2 (P56) Touch Shutter2 (P38) Dial operation guide (P135)/ Elapsed recording time (P44) Number of recordable pictures3 (P30) White Balance (P88) ISO sensitivity (P91) Exposure compensation value (P76)/ Manual exposure assistance (P94) Shutter speed (P35) Aperture value (P35) Recording Mode (P32) Metering Mode (P122) AF Mode (P82) Focus Mode (P34) Exposure meter (P133) AF area (P34, 82) Picture priorities (P108)
3 4 5 6
7 8 9 10 11 12 13
28
27 26 25 24 23
AFS
14 15
P 3.5 30
AU TO AWB
18 17
9
16
22 21 20 19
174
VQT3A48
Others
In recording (after settings) 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 Flash output adjustment (P74) 2nd curtain synchro (P123) 29 30 31 32 33 34 35 Digital Zoom (P67) FRAME RATE (P107) A 2nd nd Extra Tele Conversion (when recording 80% 52 motion pictures) (P67) 51 Extra Tele Conversion (when taking still 50 pictures) (P67) 49 Histogram (P66) 48 Travel date (P115) 36 47 C1 AFL AEL BKT 46 AF tracking operation (P49, 83) AWB R12s P 37 7 Available recording time3 (P30): White Balance Fine Adjustment (P90) 45 44 43 42 41 40 39 38 White Balance Bracket (P90) LCD recording information My Colour Mode adjustment (P104) Current date and time/: Travel 22 21 24,45 20 1,29,30 16,37 10 destination setting2, 4 (P116) Custom settings (P105) 9 P F3.5 1/30 Programme Shift (P37) 18 AE lock (P87) WB ISO AF 0 17,38,39 AWB AUTO 1 1 Face Recognition (P109) 2 2 23 AF lock (P87) 3 3 Mic level display (P129) 0 4 5,6,34 4 Age2, 5 (P101) 3 5 5 Location2, 4 (P115) STD. Simultaneous recording indicator (P108) Name2, 5 (P101) 5,7,33 9 8 2 4 19,40 Number of days that have passed since the 2, 4 departure date (P115) Self-timer6 (P81) Spot metering target (P122) Aspect Bracket (P125) WIND CUT (P129)
49 50 51 52
3 It is possible to switch the display between the number of recordable pictures and available recording time with the [REMAINING DISP.] setting in the [CUSTOM] menu. 4 This is displayed for about 5 seconds when the camera is turned on, after setting the clock and after switching from Playback Mode to Recording Mode. 5 This is displayed for about 5 seconds when this unit is turned on in [BABY1]/[BABY2] or [PET] in Scene Mode. 6 This is displayed during countdown. 7 m is an abbreviation for minute and s for second.
VQT3A48
1 Only displayed in the LCD recording information window. 2 Only displayed in the LCD monitor.
175
Others
In playback 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Playback Mode (P39) Film Mode (P118) 1 2 3 4 5 6 7 8 9 Protected picture (P152) Number of prints (P151) 1 STD. Picture size (P120) 21 1/9 : REC MODE (when recording motion 20 9 PIC. 19 pictures) (P127)/Recording quality (P127) 18 Quality (P121) 17 Intelligent Dynamic Range Control (P124) 16 Intelligent Resolution (P123) 15 Battery indication (P26) 0 16 0 P F3.5 30 Picture number/Total pictures 1 Elapsed playback time (P46): 14 13 Number of pictures in burst (P139) Detailed information display Motion picture recording time 1 (P46): 14 Playback (Motion Picture, Burst Pictures) (P46, 137) 30 F3.5 Favourites settings (P150) 0 Recording information2 WB Age (P101) ISO 160 AFS Name3 (P101, 112)/Location3 (P115)/ Title3 (P144) P STANDARD Number of days that have passed since the 10:00 1.DEC.2010 s departure date (P115) RGB 100-0001 Currently retrieving information icon (P185) / : Motion picture playback (P46) 5 6 24 : Burst Playback (P137) Histogram display Stamped with text indication (P145) Favourites (P150) 25 Cable disconnection warning icon (P167) Recorded date and time/ World Time (P116) Folder/File number2 (P166) Colour space4 (P126) Histogram (P66)
14
10 11
12
22 23
1m is an abbreviation for minute and s for second. 2 This is not displayed for motion pictures recorded in [AVCHD]. 3 It is displayed in order of [TITLE], [LOCATION], [NAME] ([BABY1]/[BABY2], [PET]), [NAME] ([FACE RECOG.]). 4 This is not displayed for motion pictures recorded in [AVCHD]/[MOTION JPEG].
F3.5
0
30
ISO160
1/9
10
100-0001
23
176
VQT3A48
Others
If you record near radio transmitters or high-voltage lines, the recorded pictures and/or sound
may be adversely affected.
Always use the supplied cords and cables. If you use optional accessories, use the cords and the cables supplied with them. Do not extend the cords or the cables. Do not spray the camera with insecticides or volatile chemicals. If the camera is sprayed with such chemicals, the body of the camera may be damaged and the Do not keep rubber or plastic products in contact with the camera for a long period of time. Cleaning Before cleaning the camera, remove the battery or the DC coupler (DMW-DCC8; optional), or disconnect the power plug from the outlet. Then wipe the camera with a dry soft cloth. When the camera is soiled badly, it can be cleaned by wiping the dirt off with a wrung wet cloth, Wipe off any dirt or dust on the zoom ring and the focus ring with a dry, dustless cloth. Do not use solvents such as benzine, thinner, alcohol, kitchen detergents, etc., to clean the When using a chemical cloth, be sure to follow the accompanying instructions.
camera, since it may deteriorate the external case or the coating may peel off. and then with a dry cloth. surface finish may peel off.
VQT3A48
177
Others
About dirt on the image sensor This camera features an interchangeable lens system so dirt may get inside the camera body when changing lenses. Depending on the recording conditions, dirt on the image sensor may appear on the recorded picture. Do not change lenses where there is a lot of dust, and always attach the body cap when a lens is not attached to the camera, so that dirt or dust does not get inside the camera body. Remove any dirt on the body cap before attaching it. Dust reduction function This unit has a dust reduction function that will blow off the debris and dust that have affixed to the front of the imaging device. This function will function automatically when the camera is turned on, but if you see dust, perform the [SENSOR CLEANING] (P136) in the [CUSTOM] menu. Removing dirt on the image sensor The image sensor is very precise and delicate, so be sure to observe the following when you do have to clean it yourself. Blow off the dust on the surface of the image sensor with a commercially available blower Do not put the blower brush further inside than the lens mount. Do not let the blower brush touch the image sensor as the image sensor may get scratched. Do not use any objects except a blower brush to clean the image sensor. If you cannot remove the dirt or dust with the blower, consult the dealer or your nearest Service
Centre. brush. Be careful not to blow too strongly.
For care of the eye cup on the viewfinder As the eye cup cannot be removed, gently wipe it with a dry and soft cloth, and be careful not to If you wipe the eye cup too hard and it is removed, consult the dealer or your nearest Service
Centre. remove it.
About the LCD monitor/Viewfinder Do not press the LCD monitor with excessive force. Uneven colours may appear on the LCD If the camera is cold when you turn it on, the picture on the LCD monitor/Viewfinder will be
monitor and it may malfunction. slightly darker than usual at first. However, the picture will return to normal brightness when the internal temperature of the camera increases.
Extremely high precision technology is employed to produce the LCD monitor/ Viewfinder screen. However there may be some dark or bright spots (red, blue or green) on the screen. This is not a malfunction. The LCD monitor/Viewfinder screen has more than 99.99% effective pixels with a mere 0.01% of the pixels inactive or always lit. The spots will not be recorded on pictures on a card.
178
VQT3A48
Others
About the Lens Do not press the lens with excessive force. Do not leave the camera with the lens facing the sun as rays of light from the sun may cause it When there is dirt (water, oil, and fingerprints, etc.) on the surface of the lens, the picture may
be affected. Lightly wipe the surface of the lens with a soft, dry cloth before and after taking pictures. Do not place the lens mount facing downwards. Do not allow the lens mount contacts 1 to become dirty. to malfunction. Also, be careful when placing the camera outside or near a window.
Battery The battery is a rechargeable lithium ion battery. Its ability to generate power comes from the chemical reaction that takes place inside it. This reaction is susceptible to the surrounding temperature and humidity. If the temperature is too high or too low, the operating time of the battery will become shorter. Always remove the battery after use. Store the removed battery in the battery case (supplied). To remove the battery, push it out by putting your finger through the
hole in the bottom of the battery case.
If you drop the battery accidentally, check to see if the body of the battery and the terminals are damaged. Inserting a damaged battery in the camera will damage the camera. Bring charged spare batteries when going out. Be aware that the operating time of the battery becomes shorter in low temperature conditions When you travel, do not forget to bring the battery charger (supplied) so that you can charge
the battery in the country that you are travelling in. such as at a ski resort.
Dispose of unusable battery. The battery has a limited life. Do not throw the battery into fire because it may cause an explosion. Do not allow battery terminals to come into contact with metal objects (such as necklaces, hairpins etc.). This can cause short circuiting or heat generation and you may be badly burned if you touch a
battery.
Charger If you use the battery charger near a radio, the radio reception may be disturbed. Keep the charger 1 m (3.28 feet) or more away from radio. The charger may generate whirring sounds when it is being used. This is not a malfunction. After use, be sure to disconnect the power supply device from the electrical outlet. (A very Keep the terminals of the charger and battery clean.
small amount of current is consumed if it is left connected.)
VQT3A48
179
Others
About 3D About 3D recording With the 3D interchangeable lens attached, do not record a subject at less than the minimum focus distance. The 3D effects may be more pronounced, and therefore cause tiredness or discomfort. When the 3D interchangeable lens (H-FT012; optional) is used, the minimum focus distance is
0.6 m (1.97 feet).
When recording with the 3D interchangeable lens attached, be careful not to shake the unit. Tiredness or discomfort may result if the shake is pronounced, due to riding in a vehicle or We recommend using a tripod. About 3D viewing Anyone who is hyper sensitive to light, suffers from heart disease or is otherwise unwell should avoid viewing 3D pictures. Doing may have an adverse affect on such medical conditions. If you feel tired, uncomfortable or otherwise strange when viewing 3D pictures, stop viewing at once. Continuing to view may cause illness. Please rest appropriately after stopping the viewing. When viewing 3D pictures, we recommend taking a break every 30 to 60 minutes. Viewing for extended periods may cause eye-fatigue. Short-sighted or long-sighted persons, those with differences in the sight of their right and left eyes, and those with astigmatism are advised to correct their vision by wearing glasses etc. Stop viewing if you can clearly see a double image while viewing 3D pictures. There are differences in the way that different people experience 3D pictures. Please correct You can change the 3D setting of your television or 3D output setting of the unit to 2D. When viewing 3D pictures on a 3D compatible television, position yourself a distance away that is least 3 times the effective height of the television. (Recommended distance): For 106.7 cm (42z); approx. 1.6 m (5.25 feet),
your sight appropriately before viewing 3D pictures. walking etc.
for 116.8 cm (46z); approx. 1.7 m (5.58 feet), for 127 cm (50z); approx. 1.9 m (6.23 feet), for 137.2 cm (54z); approx. 2.0 m (6.56 feet). Viewing from a distance closer than the recommended distance may lead to eye-fatigue.
180
VQT3A48
Others
Card Do not leave the card where the temperature is high, where electromagnetic waves or static electricity are easily generated or exposed to direct sunlight. Do not bend or drop the card. The card may be damaged or the recorded content may be damaged or deleted. Put the card in the card case or the storage bag after use and when storing or carrying the Do not allow dirt, dust or water to get into the terminals on the back of the card and do not touch
the terminals with your fingers. card.
Notice for when transferring to another party, or disposing of the memory card Format or delete using the camera or a PC will only modify the file management information,
and it will not erase the data in the memory card completely. It is recommended to physically destroy the memory card or use the commercially available computer data deletion software to completely erase the data in the memory card before transferring to another party or disposing. Management of data in the memory card is the responsibility of the user.
About the personal information If a name or birthday is set for [BABY1]/[BABY2]/Face Recognition function, this personal information is kept in the camera and recorded in the image. Disclaimer Information including personal information may be altered or vanish due to erroneous
operation, effect of static electricity, accident, malfunction, repair, or other handlings. Please note in advance that Panasonic is not liable in any way for any direct or indirect damage from the alteration or vanishing of information or personal information.
When requesting a repair, transferring to another party or disposing Reset the settings to protect the personal information. (P63) Remove the memory card from the camera when requesting a repair. Settings may return to factory default when camera is repaired. Please contact the dealer where you purchased the camera or your nearest Service Centre if
above operations are not possible due to malfunction.
When transferring to another party, or disposing of the memory card, please refer to Notice for when transferring to another party, or disposing of the memory card on P181. When not using the camera for a long period of time Store the battery in a cool and dry place with a relatively stable temperature: [Recommended Always remove the battery and the card from the camera. If the battery is left inserted in the camera, it will discharge even if the camera is turned off. If
temperature:15 oC to 25 oC (59 oF to 77 oF), Recommended humidity: 40%RH to 60%RH]
the battery continues to be left in the camera, it will discharge excessively and may become unusable even if charged. When storing the battery for a long period of time, we recommend charging it once a year. Remove the battery from the camera and store it again after it has completely discharged. We recommend storing the camera with a desiccant (silica gel) when you keep it in a closet or a cabinet. Check all the parts before taking pictures when you have not used the camera for a long period of time.
VQT3A48
181
Others
About the picture data Recorded data may be damaged or lost if the camera breaks down due to inappropriate About tripods or unipods When you use a tripod, make sure the tripod is stable when this unit is attached to it. You may not be able to remove the card or the battery when using a tripod or unipod. Make sure that the screw on the tripod or unipod is not at an angle when attaching or detaching
the camera. You may damage the screw on the camera if you use excessive force when turning it. Also, the camera body and the rating label may be damaged or scratched if the camera is attached too tightly to the tripod or unipod. When using this unit with a large-diameter lens, the lens may come into contact with the pedestal depending on the tripod/unipod. Tightening the screw with the lens and pedestal in contact with each other may damage this unit or the lens. Therefore it is recommended to attach the tripod adaptor (DMW-TA1; optional) before mounting on the tripod/unipod. Read the operating instructions for the tripod or unipod carefully. handling. Panasonic will not be liable for any damage suffered due to loss of recorded data.
About the shoulder strap If you attach a heavy interchangeable lens (more than about 1 kg) to the camera body, do not
carry the camera by the shoulder strap. Hold the camera and the lens when carrying them.
182
VQT3A48
Others
Message Display
Confirmation messages or error messages will be displayed on the screen in some cases. The major messages are described below as examples. [THIS PICTURE IS PROTECTED]
> Delete the picture after cancelling the protect setting. (P152)
[THIS PICTURE CANNOT BE DELETED]/[SOME PICTURES CANNOT BE DELETED] Pictures not based on the DCF standard cannot be deleted.
> If you want to delete some pictures, format the card after saving necessary data on a PC etc. (P63)
[NO ADDITIONAL SELECTIONS CAN BE MADE] The number of pictures, which can be set at one time when [MULTI] has been selected for
[DELETE MULTI] (P52), [FAVORITE] (P150), [TITLE EDIT] (P144), [TEXT STAMP] (P145) or [RESIZE] (P147) has been exceeded. > Reduce the number of pictures set, and then repeat the operation. More than 999 favourites have been set.
[CANNOT BE SET ON THIS PICTURE] [TITLE EDIT], [TEXT STAMP] or [PRINT SET] cannot be set for pictures not based on the
DCF standard.
[MEMORY CARD ERROR FORMAT THIS CARD?] It is a format that cannot be used with this unit.
> Format the card again with the camera after saving necessary data on a PC etc. (P63)
[LENS NOT FOUND, OR SHOOT W/O LENS IS SET TO OFF.]/ [THE LENS IS NOT ATTACHED PROPERLY. DO NOT PUSH LENS RELEASE BUTTON WHILE LENS IS ATTACHED.]/ [PLEASE CHECK THAT THE LENS IS ATTACHED CORRECTLY] Do not press the lens release button while taking pictures. When using a Leica lens mount adaptor (DMW-MA2M or DMW-MA3R; optional), set Detach the lens once, and then attach it again without pressing the lens release button. (P21)
Turn on the power again, and if it is still displaying, contact the dealer. > Use a card compatible with this unit. (P29) [SHOOT W/O LENS] (P136) to [ON] in the custom menu.
[MEMORY CARD PARAMETER ERROR]/[THIS MEMORY CARD CANNOT BE USED] SD Memory Card (8 MB to 2 GB) SDHC Memory Card (4 GB to 32 GB) SDXC Memory Card (48 GB, 64 GB)
[INSERT SD CARD AGAIN]/[TRY ANOTHER CARD] An error has occurred accessing the card.
> Insert the card again. > Insert a different card.
VQT3A48
183
Others
[READ ERROR/WRITE ERROR PLEASE CHECK THE CARD] It has failed to read or write data. The card may be broken.
> Remove the card after turning the power [OFF]. Insert the card again, turn the power on, and try to read or write the data again. > Insert a different card.
[MOTION RECORDING WAS CANCELLED DUE TO THE LIMITATION OF THE WRITING SPEED OF THE CARD] Use a card with SD Speed Class with Class 4 or higher when recording motion pictures in
[AVCHD]. Also, use a card with SD Speed Class with Class 6 or higher when recording motion pictures in [MOTION JPEG]. In the event that it stops even after using a Class 4 card or higher, the data writing speed has deteriorated so it is recommended to make a backup and then format (P63). Depending on the type of the card, motion picture recording may stop in the middle.
[THIS CARD IS NOT FORMATTED WITH THIS CAMERA, AND NOT SUITABLE FOR MOVIE RECORDING.] The writing speed is lower if the card has been formatted using a PC or other equipment. As a
consequence, motion picture recording may stop in the middle. If this happens, make a backup of the data and format (P63) the card in this unit.
[A FOLDER CANNOT BE CREATED] A folder cannot be created because there are no remaining folder numbers that can be used.
(P166) > Format the card after saving necessary data on a PC etc. (P63) If you execute [NO.RESET] in the [SETUP] menu after formatting, the folder number is reset to 100. (P63)
[PICTURE IS DISPLAYED FOR 16:9 TV]/[PICTURE IS DISPLAYED FOR 4:3 TV] The AV cable is connected to the camera.
> Press [MENU/SET] if you want to delete this message at once. > Select [TV ASPECT] in the [SETUP] menu if you want to change the TV aspect. (P60) This message also appears when the USB connection cable is connected to the camera only. In this case, connect the other end of the USB connection cable to a PC or a printer. (P164, 167)
[THIS BATTERY CANNOT BE USED] The battery cannot be recognised by the camera.
> Use a genuine Panasonic battery. If this message is displayed even when a genuine Panasonic battery is used, contact the dealer or your nearest Service Centre. The battery cannot be recognised as its terminal is dirty. > Remove any dirt etc. from the terminal.
[PLEASE MAKE SURE TO TURN ON THE POWER OF EXTERNAL MICROPHONE.] When attaching the stereo microphone (DMW-MS1; optional), check the battery status and
make sure the power is on before use. (P173)
VQT3A48
184
Others
[EDITING OPERATION CANNOT PROCEED AS INFORMATION PROCESSING IS ONGOING.] When a card with pictures deleted or file names changed using a PC or other device is inserted into this unit, it will automatically retrieve new information and reconstruct the burst groups. The currently retrieving information icon [ ] may be displayed in the playback screen for long period of time when there are many image files, and deletion or [PLAYBACK] Mode menu cannot be used during this time. If you switch the power switch to [OFF] while information is being retrieved, the pictures for
which information was retrieved up to that point will be saved as a burst group. When you switch on again, the information retrieval will restart from the same point.
VQT3A48
185
Others
Troubleshooting
First, try out the following procedures (P186194). If the problem is not resolved, it may be improved by selecting [RESET] (P63) on the [SETUP] menu.
> Turn the camera off frequently by using the [ECONOMY] Mode etc. (P59)
This unit is turned off automatically. If you connect to a TV compatible with VIERA Link with a HDMI mini cable (optional) and turn
off the power on the TV with the remote control for the TV, the power on this unit also turns off. > If you are not using VIERA Link, set [VIERA Link] to [OFF]. (P61)
The [CHARGE] lamp flashes. Is the temperature of the battery excessively high or low? If it is, it will take longer than usual to Are the terminals of the charger or battery dirty?
> Wipe off the dirt using a dry cloth. charge the battery or charging may remain incomplete.
Recording
Taking pictures is not possible. The shutter will not operate immediately when the shutter button is pressed. Is the subject focused?
> [FOCUS PRIORITY] is set to [ON] at the time of purchase, and so you cannot take pictures until the subject is in focus. If you want to be able to take a picture when you press the shutter button fully even if the subject is not focused, set [FOCUS PRIORITY] in the [CUSTOM] menu to [OFF]. (P131) You may not be able to record for a short while after turning the power [ON] when using a large capacity card.
The recorded picture is whitish. Picture might look whitish when lens or image sensor gets dirty with finger print or similar.
> If the lens is dirty turn the camera off and then gently wipe the lens surface with a soft dry cloth. > Refer to P178 when the image sensor gets dirty.
186
VQT3A48
Others
The subject is not focused properly. The subject is beyond the focus range of the camera. (P34) There is camera shake (jitter) or the subject is moving slightly. (P75) Is [FOCUS PRIORITY] in the [CUSTOM] menu set to [OFF]? (P131)
In this case, the picture may not be properly focused even if [AFS] or [AFC] in Focus Mode is set. Is [SHUTTER AF] in the [CUSTOM] menu set to [OFF]? (P132) Is the AF Lock (P87) applied incorrectly?
The recorded picture is blurred. The Optical Image Stabilizer is not effective. The shutter speed will become slower and the Optical Image Stabilizer function may not work
properly when taking pictures especially in dark places. > We recommend holding the camera firmly with both hands when taking pictures. (P36) > We recommend using a tripod and the self-timer (P81) when taking pictures with a slow shutter speed.
Taking pictures using White Balance Bracket/[ASPECT BRACKET] is not possible. Is there any memory remaining on the card? The recorded picture looks rough. Noise appears on the picture. Is the ISO sensitivity high or the shutter speed slow?
(ISO sensitivity is set to [AUTO] when the camera is shipped. Therefore, when taking pictures indoors etc. noise will appear.) > Decrease the ISO sensitivity. (P91) > Increase the setting for [NOISE REDUCTION] in [FILM MODE] or lower the setting for each of the items other than [NOISE REDUCTION]. (P118) > Take pictures in bright places. > Set the [LONG SHTR NR] to [ON]. (P124) Is the [PICTURE SIZE] (P120) or the [QUALITY] (P121) set low? Is the [DIGITAL ZOOM] set? (P67)
Under fluorescent lighting, flicker or horizontal bars may be seen. This is characteristic of MOS sensors which serve as the cameras pickup
sensors. This is not a malfunction. If the flicker or horizontal bars stand out, record in the Creative Motion Picture Mode and set the shutter speed to 1/100 in areas where the supply frequency is 50 Hz, or 1/60 in areas of 60 Hz.
VQT3A48
187
Others
The brightness or the hue of the recorded picture is different from the actual scene. If recording under fluorescent light, the brightness or the hue may change slightly when the
shutter speed becomes fast. This occurs due to the characteristics of fluorescent light. It is not a malfunction. Colour or brightness of the screen may change or horizontal streaks may appear on the screen when the picture is taken under extremely bright light, or under fluorescent lamps, mercury lamps, or sodium lamps etc.
Reddish horizontal streaks appear on the LCD monitor during recording. This is characteristic of MOS sensors which serve as the cameras pickup sensors. It appears
when the subject has a bright part. Some unevenness may occur in the surrounding areas, but this is not a malfunction. It is recommended that you take pictures while taking care not to expose the screen to sunlight or any other source of strong light.
Bright spot not in subject is recorded. This could be an inactive pixel. Perform the [PIXEL REFRESH] (P135) in the [CUSTOM] menu. You cannot compensate the exposure. Are you in Exposure Compensation operation? Subject cannot be locked. (AF tracking not possible) Set the AF area to the distinctive colour of the subject if there is a part that is different from the
surrounding colour. (P83) > Press the rear dial to switch to Exposure Compensation operation. (P76)
Motion pictures
Motion picture recording stops in the middle. Use a card with SD Speed Class with Class 4 or higher when recording motion pictures in
[AVCHD]. Also, use a card with SD Speed Class with Class 6 or higher when recording motion pictures in [MOTION JPEG]. Depending on the type of the card, recording may stop in the middle. > If motion picture recording stops during use of a card of at least Class 4 or if you use a card on which recording and deleting have been repeated many times, or a card that has been formatted on a PC or other equipment, the data-writing speed is lower. In such cases, we recommend that you make a backup of the data and then format (P63) the card in this unit.
When recording a motion picture, the screen may go dark. When recording a motion picture, the screen may go dark after a certain period to reduce
battery consumption, but this will not affect the recorded motion picture.
188
VQT3A48
Others
The screen may be blacked out momentarily, or the unit may record noise.
The screen may be blacked out momentarily, or the unit may record noise due to static
electricity or electromagnetic waves etc. depending on the environment of the motion picture recording.
Object seems to be warped. Object seems to be warped slightly when the object moves across the image very fast, but this
is because the unit is using MOS for the image sensor. This is not a malfunction.
In motion pictures, abnormal clicking and buzzing sounds are recorded. With recording in a quiet environment, depending on the lenses used, the sound of aperture
and focus actions may be recorded in motion pictures. This is not a malfunction. Focus operation while recording motion pictures can be set to [OFF] with [CONTINUOUS AF] (P43). Be careful while recording motion pictures because the sounds of the zoom operations, buttons and dial operation etc. may be recorded.
Lens
Recorded image may be warped, or nonexistent colour is surrounding the subject. Depending on the lens used, picture may be warped slightly or you may see colours along the
edge depending on the zoom factor, due to the characteristics of the lens. Also, the peripherals of the image might look warped because the perspective is enhanced when the wide angle is used. This is not a malfunction.
When the lens is attached to another digital camera, stabilizer function cannot be turned off or stabilizer function does not work. The Optical Image Stabilizer function of the 14 42 mm/F3.5 5.6 lens supplied in DMC-GH2K
only works correctly with supported cameras. > When older Panasonic digital cameras (DMC-GF1, DMC-GH1, DMC-G1) are used, [STABILIZER] in the [REC] Mode menu (P75) cannot be set to [OFF]. It is recommended to update the firmware of the digital camera at the following website. http://panasonic.jp/support/global/cs/dsc/download/ > When using this lens with another make of digital cameras, the Optical Image Stabilizer function will not work. (As of October 2010) For details, contact the respective company.
Flash
The flash is not activated. Is the flash closed?
> Slide the [ OPEN] lever to open the flash. (P69)
The flash is activated 2 times. The flash is activated 2 times. The interval between the first and second flash is longer when
Red-eye Reduction (P70) is set so the subject should not move until the second flash is activated.
VQT3A48
189
Others
LCD monitor/Viewfinder
The LCD monitor turns off although the camera is turned on. The LCD monitor turns off when [AUTO LCD OFF] (P59) is selected for the [ECONOMY] Mode. It will switch to viewfinder display if there is hand or object near the eye sensor. (P16) The LCD monitor/Viewfinder is too bright or dark.
> Adjust the brightness of the LCD monitor/viewfinder to a proper level. (P58) Check [LCD MODE] setting. (P59) It may flicker for an instant or the brightness of the screen may change significantly for an instant. [This does not happen when using the AC adaptor (DMW-AC8E; optional).]
This occurs due to the aperture of the lens changing when the shutter button is pressed
half-way, or when the brightness of the subject changes. This is not a malfunction.
The picture is not displayed on the LCD monitor. Does the picture appear on the viewfinder? Is the LCD monitor switched off?
> Press [LVF/LCD] to switch to LCD monitor display. (P16) > Switch the display by pressing [DISPLAY]. (P64)
LCD monitor and viewfinder do not switch when [LVF/LCD] is pressed. Is the [EXPO. SETTINGS] set to [SWITCH BY PRESSING THE LVF/LCD BUTTON]? (P133) It is only displayed on the LCD monitor when the camera is connected to a PC or printer. Black, red, blue and green dots appear on the LCD monitor. This is not a malfunction.
These pixels do not affect the recorded pictures.
Noise appears on the LCD monitor. In dark places, noise may appear to maintain the brightness of the LCD monitor. You see red, green, or blue flashes when you move your eyes in the viewfinder, or when the camera is moved rapidly. This is a characteristic of the drive system of the viewfinder of this unit, and it is not a
malfunction. There will be no problem with the recorded image.
190
VQT3A48
Others
Playback
The picture being played back is not rotated, or is rotated in an unexpected direction, when displayed. You can display the pictures without being rotated when [ROTATE DISP.] (P149) is set to You can rotate pictures with the [ROTATE] function. (P149) You can only display the pictures rotated if you use a lens (P19) that supports the Direction
Detection Function (P36) and [ROTATE DISP.] is set to [ON]. [OFF].
The picture is not played back. There are no recorded pictures. Did you press [(]? Is the card inserted? Is there a picture on the card? Is this a picture whose file name has been changed in the PC? If it is, it cannot be played back Has [PLAYBACK MODE] been set for playback?
> Change to [NORMAL PLAY]. (P143) by this unit.
The folder number and the file number are displayed as [] and the screen turns black. Is this a non-standard picture, a picture which has been edited using a PC or a picture which Did you remove the battery immediately after picture-taking or did you take the picture using a
battery with a low remaining charge? > Format the data to delete the pictures mentioned above. (P63) was taken by another make of digital camera?
(Other pictures will be deleted as well and it will not be possible to restore them. Therefore, check well before formatting.)
Images with different date as recorded date are played back in the Calendar Playback. Is the clock in the camera set properly? (P31) Images edited on a PC or images recorded on other cameras might display a different date to
the recorded date during the Calendar Playback.
White round spots like soap bubbles appear on the recorded picture. If you take a picture with the flash in a dark place or indoors, white round
spots may appear on the picture caused by the flash reflecting of particles of dust in the air. This is not a malfunction. A characteristic of this is that the number of round spots and their position differ in every picture.
[THUMBNAIL IS DISPLAYED] appears on the screen. Is it a picture that has been recorded with other equipment? In such cases, these pictures may
be displayed with a deteriorated picture quality.
VQT3A48
191
Others
Red part of the recorded image has changed colour to black. When Digital Red-Eye Correction ([ ], [ ], [ ]) is in operation, if you take a picture of subject with red colour surrounded by a skin tone colour, that red part may be corrected to black by the Digital Red-Eye Correction function. > It is recommended to take pictures with the flash closed, Flash Mode set to [] or [], or [RED-EYE REMOVAL] set to [OFF]. (P123)
The display areas on the TV screen and the cameras LCD monitor are different. Depending on the TV model, the pictures may be extended horizontally or vertically or they
may be displayed with their edges cut off.
The motion pictures cannot be played back on a TV. Are you trying to play back the motion pictures by directly inserting the card in the card slot of
the TV? > Connect the camera to the TV with the AV cable (supplied), or with the HDMI mini cable (optional), and then play back the motion pictures on the camera. (P157, 158) > Motion pictures recorded in [AVCHD] can be played back on Panasonic televisions (VIERA) with the AVCHD logo.
VIERA Link does not work. Is it connected properly with the HDMI mini cable (optional)? (P158)
> Confirm that the HDMI mini-cable (optional) is firmly fitted. > Press [(] on this unit. Is the [VIERA Link] on this unit set to [ON]? (P61) > Depending on HDMI terminal of the TV, the input channel may not switch automatically. In this case, use the remote control for the TV to switch input. (For details on how to switch input, please read the operating instructions for the TV.) > Check the VIERA Link setting on the connected device. > Turn the power to the unit off and then back on again. > Set [VIERA Link] to [Off] on the TV and then turn it back to [On]. (Refer to the operating instructions of the TV for details.) > Check [VIDEO OUT] setting. (P60)
The picture cannot be transferred when the camera is connected to a PC. Is the camera connected to the PC correctly? Is the camera recognised by the PC correctly?
> Set to [PC] in [USB MODE]. (P60, 164)
VQT3A48
192
Others
The card is not recognised by the PC. (SDXC memory card is used)
> Check if your PC is compatible with SDXC memory cards. http://panasonic.net/avc/sdcard/information/SDXC.html > A message prompting to format the card may be displayed when connecting, but do not format. > If the [ACCESS] displayed on the LCD monitor does not disappear, disconnect the USB connection cable after turning off the power.
The picture cannot be printed when the camera is connected to a printer. Pictures cannot be printed using a printer which does not support PictBridge.
> Set to [PictBridge(PTP)] in [USB MODE]. (P60, 167)
Others
The camera makes a noise when turned [ON]. This is the noise of the Dust Reduction Function working (P178); it is not a malfunction. There is a sound from lens unit. It is a sound of lens movement or aperture operation when the power is turned [ON] or [OFF], You may hear a sound from the lens and image in the LCD monitor may suddenly change when
the brightness has changed by zoom operation or moving the camera, but there is no effect on recording. The sound is caused by the automatic adjustment of the aperture. This is not a malfunction. and it is not a malfunction.
Part of the picture is flashing in black and white. This is a highlight function showing the white saturated area. (P130) Is the [HIGHLIGHT] set to [ON]? A red lamp sometimes turns on when the shutter button is pressed halfway. In dark places, the AF Assist Lamp (P132) lights red to make it easier to focus on a subject.
VQT3A48
193
Others
The AF Assist Lamp does not turn on. Is [AF ASSIST LAMP] on the [CUSTOM] menu set to [ON]? (P132) The AF Assist Lamp does not turn on in bright places. The camera becomes warm. The surface of the camera and the reverse side of the LCD monitor may become warm during
use. This does not affect the performance or quality of the camera.
The clock is reset. If you do not use the camera for a long time, the clock may be reset.
> [PLEASE SET THE CLOCK] message will be displayed; please re-set the clock. When taking pictures, it will not be possible to record the correct date without setting the clock. (P31)
The file numbers are not recorded consecutively. When you perform an operation after taking a certain action, the pictures may be recorded in
folders with different numbers from the ones used prior to the operation. (P166)
The file numbers are recorded in ascending order. If the battery was inserted or removed without first turning the cameras power off, the folder
and file numbers for the pictures taken will not be stored in the memory. When the power is then turned back on and pictures are taken, they may be stored under file numbers which should have been assigned to previous pictures.
Age is not displayed correctly. Check the clock (P31) and birthday settings (P101). A different thing gets selected from what you touched.
> Perform the calibration (P62).
194
VQT3A48
Others
Others
Specifications
Digital Camera Body (DMC-GH2): Power Source: Power Consumption: Information for your safety DC 8.4 V 3.4 W (When recording with LCD Monitor) (When the 14 140 mm/F4.0 5.8 lens supplied in DMC-GH2H is used) 3.2 W (When recording with LCD Monitor) (When the 14 42 mm/F3.5 5.6 lens supplied in DMC-GH2K is used) 2.6 W (When playing back with LCD Monitor) (When the 14 140 mm/F4.0 5.8 lens supplied in DMC-GH2H is used) 2.5 W (When playing back with LCD Monitor) (When the 14 42 mm/F3.5 5.6 lens supplied in DMC-GH2K is used)
Camera effective pixels: 16,050,000 pixels Image sensor: 4/3q Live MOS sensor, total pixel number 18,310,000 pixels, Primary colour filter Digital Zoom: Max. 4k Extra Tele Conversion: ON/OFF simple enlargement (compatible with lenses from (Except for the maximum other manufacturers) picture size for each aspect ratio) Focus: Auto Focus/Manual Focus, Face Detection/AF Tracking/23-area-focusing/1-area-focusing (Touch focus area selection possible) Shutter system: Focal-plane shutter Burst recording Burst speed: 40 pictures/second (Super high speed), 5 pictures/second (High speed), 3 pictures/second (Middle speed), 2 pictures/second (Low speed) Number of recordable pictures: Max. 7 pictures (when there are RAW files) Depends on the capacity of the card (when there are no RAW files) ISO sensitivity (Standard Output Sensitivity): AUTO/ /160/200/250/320/400/500/640/800/1000/1250/1600/ 2000/2500/3200/4000/5000/6400/8000/10000/12800
VQT3A48
195
Others
Minimum Illumination:
Approx. 6 lx (when i-Low light is used, the shutter speed is 1/25th of a second), Approx. 1 lx (when Creative Motion Picture Mode is used, [ISO3200] is set, the shutter speed is 1/2th of a second) (When the 14 140 mm/F4.0 5.8 lens supplied in DMC-GH2H is used) Approx. 5 lx (when i-Low light is used, the shutter speed is 1/25th of a second), Approx. 1 lx (when Creative Motion Picture Mode is used, [ISO3200] is set, the shutter speed is 1/2th of a second) (When the 14 42 mm/F3.5 5.6 lens supplied in DMC-GH2K is used) B (Bulb) (Max. approx. 120 seconds), 60 seconds to 1/4000th of a second Taking still pictures during motion picture recording Motion picture priorities: 1/25th of a second to 1/16000th of a second Still picture priorities: B (Bulb) (Max. approx. 120 seconds), 60 seconds to 1/4000th of a second EV 0 to EV 18 Auto White Balance/Daylight/Cloudy/Shade/Incandescent lights/Flash/White set1/White set2/White set3/White set4/White Balance K set Programme AE (P)/Aperture-priority AE (A)/Shutter-priority AE (S)/Manual exposure (M)/AUTO Exposure Compensation (1/3 EV Step, j5 EV to i5 EV) Multiple/Centre weighted/Spot 3.0q TFT LCD (3:2) (Approx. 460,000 dots) (field of view ratio about 100%) Touch panel Colour LCD Viewfinder (Approx. 1,530,000 dots) (field of view ratio about 100%) (with diopter adjustment j4 to i4 diopter) Built-in pop up flash GN 13.9 equivalent (ISO160 m) Flash range: Approx. 1.0 m (3.28 feet) to 4.8 m (15.7 feet) (When the 14 140 mm/F4.0 5.8 lens supplied in DMC-GH2H is mounted, focal length is 22 mm, [ISO AUTO] is set, and the aspect ratio is set to [X]) Flash range: Approx. 45 cm (1.48 feet) to 6.2 m (20.3 feet) (When the 14 42 mm/F3.5 5.6 lens supplied in DMC-GH2K is mounted, WIDE, [ISO AUTO] is set) AUTO, AUTO/Red-Eye Reduction, Forced ON, Forced ON/ Red-eye reduction, Slow Sync., Slow Sync./Red-Eye Reduction, Forced OFF Equal to or smaller than 1/160th of a second
Shutter speed:
Exposure (AE):
Viewfinder:
Flash:
196
VQT3A48
Others
Stereo Monaural SD Memory Card/SDHC Memory Card/SDXC Memory Card When the aspect ratio setting is [X] 4608k3456 pixels, 3264k2448 pixels, 2336k1752 pixels When the aspect ratio setting is [Y] 4752k3168 pixels, 3360k2240 pixels, 2400k1600 pixels When the aspect ratio setting is [W] 4976k2800 pixels, 3520k1984 pixels, 1920k1080 pixels When the aspect ratio setting is [ ] 3456k3456 pixels, 2448k2448 pixels, 1744k1744 pixels [AVCHD] (With audio) When set to [24H]: 1920k1080 pixels (24p recording/Approx. 24 Mbps)/ When set to [24L]: 1920k1080 pixels (24p recording/Approx. 17 Mbps)/ When set to [FSH]: 1920k1080 pixels (50i recording/Approx. 17 Mbps)/ When set to [FH]: 1920k1080 pixels (50i recording/Approx. 13 Mbps)/ When set to [SH]: 1280k720 pixels (50p recording/Approx. 17 Mbps)/ When set to [H]: 1280k720 pixels (50p recording/Approx. 13 Mbps) [MOTION JPEG] (With audio) When set to [HD]: 1280k720 pixels (30 frames/sec.)/ When set to [WVGA]: 848k480 pixels (30 frames/sec.)/ When set to [VGA]: 640k480 pixels (30 frames/sec.)/ When set to [QVGA]: 320k240 pixels (30 frames/sec.) RAW/RAWiFine/RAWiStandard/Fine/Standard/MPOiFine/ MPOiStandard RAW/JPEG (based on Design rule for Camera File system, based on Exif 2.3 standard, DPOF corresponding)/MPO
Motion pictures with audio: AVCHD/QuickTime Motion JPEG Interface Digital: USB 2.0 (High Speed) Analogue video/ audio: NTSC/PAL Composite (Switched by menu) Audio line output (stereo) Terminal [MIC/REMOTE]: 2.5 mm jack [AV OUT/DIGITAL]: Dedicated jack (14 pin) [HDMI]: MiniHDMI TypeC
VQT3A48
197
Others
Approx. 124 mm (W)k89.6 mm (H)k75.8 mm (D) [4.88q (W)k3.53q(H)k2.98q (D)] (excluding the projecting parts) Mass: Approx. 904 g/1.99 lb (with the 14 140 mm/F4.0 5.8 lens supplied in DMC-GH2H, card and battery) Approx. 609 g/1.34 lb (with the 14 42 mm/F3.5 5.6 lens supplied in DMC-GH2K, card and battery) Approx. 392 g/0.86 lb (camera body) Operating temperature: 0 oC to 40 oC (32 oF to 104 oF) Operating humidity: 10%RH to 80%RH Battery Charger (Panasonic DE-A80A): Input: Output: Battery Pack (lithium-ion) (Panasonic DMW-BLC12E): Voltage/capacity: Information for your safety AC DC 110 V to 240 V, 50/60 Hz, 0.2 A 8.4 V, 0.65 A
Dimensions:
198
VQT3A48
Others
Interchangeable Lens (H-VS014140) LUMIX G VARIO HD 14 140 mm/F4.0 5.8 ASPH./MEGA O.I.S. Focal length: f=14 mm to 140 mm (35 mm film camera equivalent: 28 mm to 280 mm) Aperture type: 7 diaphragm blades/circular aperture diaphragm Aperture range: F4.0 (Wide) to F5.8 (Tele) Minimum aperture value: F22 Lens construction: 17 elements in 13 groups (4 aspherical lenses/2 ED lenses) In focus distance: 0.5 m (1.64 feet) to (from the focus distance reference line) Maximum image magnification: 0.2k (35 mm film camera equivalent: 0.4k) Optical Image Stabilizer: Available [O.I.S.] switch: Available (Switching ON/OFF) Mount: Micro Four Thirds Mount Angle of view: 75x (Wide) to 8.8x (Tele) Filter diameter: 62 mm (2.44 inch) Max. diameter: Approx. 70 mm (2.76 inch) Overall length: Approx. 84 mm (3.31 inch) (from the tip of the lens to the base side of the lens mount) Mass: Approx. 460 g/1.01 lb Interchangeable Lens (H-FS014042) LUMIX G VARIO 14 42 mm/F3.5 5.6 ASPH./MEGA O.I.S. Focal length: f=14 mm to 42 mm (35 mm film camera equivalent: 28 mm to 84 mm) Aperture type: 7 diaphragm blades/circular aperture diaphragm Aperture range: F3.5 (Wide) to F5.6 (Tele) Minimum aperture value: F22 Lens construction: 12 elements in 9 groups (1 aspherical lens) In focus distance: 0.3 m (0.99 feet) to (from the focus distance reference line) Maximum image magnification: 0.16k (35 mm film camera equivalent: 0.32k) Optical Image Stabilizer: Available [O.I.S.] switch: None (Setting of the [STABILIZER] is done in [REC] Mode menu.) Mount: Micro Four Thirds Mount Angle of view: 75x (Wide) to 29x (Tele) Filter diameter: 52 mm (2.05 inch) Max. diameter: Approx. 60.6 mm (2.39 inch) Overall length: Approx. 63.6 mm (2.50 inch) (from the tip of the lens to the base side of the lens mount) Mass: Approx. 165 g/0.22 lb
VQT3A48
199
camera system of LUMIX based on a Micro Four Thirds System standard. Micro Four Thirds and Micro Four Thirds Logo marks are trademarks or registered trademarks of Olympus Imaging Corporation, in Japan, the United States, the European Union and other countries. Four Thirds and Four Thirds Logo marks are trademarks or registered trademarks of Olympus Imaging Corporation, in Japan, the United States, the European Union and other countries. SDXC Logo is a trademark of SD-3C, LLC. The AVCHD and the AVCHD logo are trademarks of Panasonic Corporation and Sony Corporation. Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries. HDAVI Control is a trademark of Panasonic Corporation. QuickTime and the QuickTime logo are trademarks or registered trademarks of Apple Inc., used under license therefrom. Adobe is a trademark or registered trademark of Adobe Systems Incorporated in the United States and/or other countries. Microsoft product screen shot(s) reprinted with permission from Microsoft Corporation. Other names, company names, and product names printed in these instructions are trademarks or registered trademarks of the companies concerned. This product is licensed under the AVC patent portfolio license for the personal and non-commercial use of a consumer to (i) encode video in compliance with the AVC Standard (AVC Video) and/or (ii) decode AVC Video that was encoded by a consumer engaged in a personal and non-commercial activity and/or was obtained from a video provider licensed to provide AVC Video. No license is granted or shall be implied for any other use. Additional information may be obtained from MPEG LA, LLC. See http://www.mpegla.com.
EU
B
VQT3A48
F1010SM0
Pursuant to at the directive 2004/108/EC, article 9(2) Panasonic Testing Centre Panasonic Marketing Europe GmbH Winsbergring 15, 22525 Hamburg, Germany
Panasonic Corporation
Web Site: http://panasonic.net