Is 2950 (Part-I) Code of Practice For Design and Constructio
Is 2950 (Part-I) Code of Practice For Design and Constructio
IS:2950(PartI)-1981
Indian Standard
( Reaffirmed 1998 )
f Second Revision)
Second Reprint MAY 1994 UDC.
624.153.61:624.0:69.001.3
@ Copvrighl 1982
BUREAU
MkhAK
OF INDIAN
9 BqHADUR NEW DELHI 110002
STANDARDS
SHAH ZAFAR MARG
BHAVAN,
Gr6
September
1982
Indian Standard
CODE OF PRACTICE FOR DESIGN AND CONSTRUCTION OF RAFT FOUNDATIONS
PART I DESIGN
Second Revision I
Engineerhg Sectional Committee, BDC 43
Representing
Cen~oor~lding Research
Foundation
Chairman
PROF DINFX~ MOHAN
Institute ( CSIR 1,
Institute (
Members
DR R. K. BHANDARI Cen&Rdor~~lding Research
CSIR 1,
SHRI DEVENDRASHARMA ( Alternate ) CHIEF ENGINEER Calcutta Port Trust, Calcutta SHRI S. GUI~A ( Alternate ) SHRI M. G. DANDAVA~ The Concrete Association of India, Bombay SHRI N. C. DUGGAL ( Alternate ) SHRI R. K. DAS GUPTA Simplex Concrete Piles ( India ) Pvt Ltd, Calcutta SI-IRIH. GUHA BISWAS ( Afternate ) SHRI A. G. DASTIDAR In personal capacity ( 5, Hungerford Road 121, SHRI V. C. DESHPANDE DIRECTOR ( CSMRS ) DEPUTY DIRECTOR ( CSMRS SHRI A. H. DIVANJI The Pressure Piling Co ( I ) Pvt Ltd. Bombay Central Water Commission, New Delhi and Construction Co Pvt Ltd,
SHRI A. N. JANGLE ( Alternate ) SHRI A. GHOSHAL Stup Consultams Ltd, Bombay PROF GOPAL RANJAN University of Roorkee, Roorkee DR JAGDISHNARAIN Indian Geotecbnic Society, New Delhi PROP SWAMI SARAN ( Alternate )
SHRIV. M. MADGE Alternate ) ( Cemindia Co Ltd. Bomb&y SHRIM. R. PUNJA SHRIS. MUKHERJEE Alternate ) ( The Braithwaite Born & Jessop Construction Co SHRIN. B. V. RA~HVAN Ltd, Calcutta Vijayanagar Steel Plant ( SAI ), New Delhi SHRIA. A. RAJU Nagadi Consultants Pvt Ltd, New Delhi DR Vi V. S. RAO Cement Corporation of Indta, New Delhi SHRIARJUNRIJHSINGHANI SHRI0. S. SRIVASTAVA ( Alternate ) College of Engineering, Guindy DR A. SARGUNAN SHRIS. B~~MINATHANAlternate ) ( Public Works Department, Government of Andbra SHRI K. R. SAXENA Pradesh,.Hyderabad United Technical Consultants Pvt Ltd, New Delhi DR S. P. SHRIVASTAVA DR R. KAPUR( Alternate ) Gammon India Limited, Bombay SHRIT. N. SURBA RAO SHRIS. A. REDDI( Alternate ) Ministry of Shipping and Transport, New Delhi SHR~ SIVAGURU N. SHRID. V. SIKKA Alternate ) ( Central Public Works Department, New Delhi SUPERINTENDING G I N E E R E N ( DESIGNS ) EXECUTIVE ENGINEER DESIGNS V ( ) ( Alternate ) ( Continued on page 24)
Indian Standard
CODE OF PRACTICE FOR DESIGN AND CONSTRUCTION OF RAFT FOUNDATIONS
PART I DESIGN
Second Revision)
0. FOREWORD
0.1 This Indian Standard ( Part I ) was adopted by the Indian Standards Institution on 5 October 1981, after the draft finalized by the Foundation Engineering Sectional Committee had been approved by the Civil Engineering Division Council. 0.2 Raft foundation is a substructure supporting an arrangement of columns or walls in a row or rows and transmitting the loads to the soil by means of a continuous slab with or without depressions or openings. Such types of foundations are found useful where soil has low bearing capacity. This standard was first published in 1965 and revised in 1973. In this revision, besides making its contents up-to-date, guidelines have been given to choose particular type of methods in particular situations and giving reference to finite difference method which will be covered at a later stage. 0.3 For the purpose of deciding whether a particular requirement of this standard is complied with, the final value, observed or calculated, expressing the result of a test, shall be rounded off in accordance with IS : 2-1960*. The number of significant places retained ,in the rounded off value should be same as that of the specified value in this standard. 1. SCOPE 1.1 This standard ( Part I ) covers the design of raft foundation based on conventional method ( for rigid foundation ) and simplified methods (flexible foundation ) for residential and industrial buildings, store-houses, silos, storage tanks, etc, which have mainly vertical and evenly distributed loads. *Rules for rounding off numerical values ( revised ). 3
IS : 2950 ( Part I ) - 1981 2. TERMINOLOGY 2.1 For the purpose of this standard, IS : 2809-1972* shall apply.
the definitions
of terms given in
3. NECESSARY INFORMATION
3.1 For satisfactory design and construction following information is necessary:
of a raft foundation,
the
a)
Site Plan - Site plan showing the location of the proposed as well as neighbouring structure.
b)
Building plan and vertical cross-sections levels, ducts and openings, etc, layout columns, shear walls, etc. design combination
Environmental Factors - Information relating to geologic history of the area, seismicity of the region, hydrological information indicating ground water conditions and its seasonal variations, climatic factors like vulnerability of the site to sudden flooding by surface run-off, erosion, etc. Geotechnical Information - Giving subsurface profile with stratification details ( see IS : 1892-1979t ), engineering properties of the
e)
founding strata, namely, index properties, effective shear parameters determined under appropriate drainage conditions, compressibility characteristics, swelling properties, results of field tests like static and dynamic penetration tests, pressure meter tests, etc.
f)
Modulus of Elasticity and Modulus of Subgrade Reaction - Appendix A enumerates the methods of determination of modulus of elasticity ( E, ) and Poissons ratio ( k ). The modulus of subgrade reaction ( k ) may be determined in accordance with Appendix B.
h)
*Glossary of tempt and symbols relating to soil engineering(first revision ). tCode of practice for subsurfaceinvestigationsfor foundations (first revision ). ICode of practice for structural safety of buildings : Shallowfoundations ( second
revision ).
3 Information
necessary to assess the possible effects of the new structure on the existing structures in the neighbourhood. the less the for
4.1 Choice of Raft Type 4.1.1 For fairly small and uniform column spacing and when the supporting soil is not too compressible, a flat concrete slab having uniform thickness throughout ( a true mat ) is most suitable ( see Fig. 1A ). 4.1.2 The slab may be thickened under heavily loaded columns to provide adequate strength for shear and negative moment. Pedestals may also be provided in such cases ( see Fig. 1B ). 4.1.3 A slab and beam type of raft is likely to be more economical for large column spacing and unequal column loads, particularly when the supporting soil is very compressible ( see Fig. 1C ). 4.1.4 For very heavy structures, provision of cellular raft or rigid frames consisting of slabs and basement walls may be considered. 4.2 Allowable Bearing Pressure - The allowable bearing pressure shall be determined in accordance with IS : 6403-1981*. 4.2.1 In granular soils, the ultimate bearing capacity of rafts is generally very large. However, for rafts placed at considerable depth ( for example basement rafts ), the possibility of punching mode of failure should be investigated. The influence of soil compressibility and related scale effects should also be assessed. 4.2.2 For rafts on cohesive soils stability against deep seated failures shall be analysed. 4.2.3 In cohesive soils, the effect of long term settlement due to consideration shall be taken into consideration. 4.3 Depth of Foundation less than 1 m. The depth of foundation shall generally be not
*Code of practice for determination of bearing capacity of shallow foundation (first revision ).
5
IS :295O(PartI)-1981
to
0
0 0
0 0
0 0
0
cl
0 0
0 0
a
0
d
0
Cl
cl
SECTION
1A Fiat Plate
AA
SECTION
BB
SECUON CC
1C Two-Way Beam and Slab ID
SECTION
00
IS:29!5o(PartI)-1981 4.4 Sub-soil Water Pressure considered in the design. The uplift due to the sub-soil water shall be
4.4.1 All construction below the ground water level shall be checked for flotation. 4.5 General 4.5.1 Dimensional Parameters - The size and shape of the foundation adopted affect the magnitude of subgrade modulus and long term deformation of the supporting soil and this, in turn, influence the distribution of contact pressure. This aspect shall be taken into consideration in the analysis. 4.5.2 Eccentricity of the building and portion it coinciding resultant force. In pressure distribution
of Loading -
A raft generally occupies the entire area often it is not feasible and rather uneconomical to prothe centroid of the raft with the line of action of the such cases, the effect of the eccentricity on contact shall be taken into consideration.
4.5.3 Properties of the Supporting Soil - Distribution of contact pressure underneath a raft is affected by the physical characteristics of the soil supporting it. Considerations must be given to the increased contact pressure developed along the edges of the foundation on cohesive soils and the opposite effect on granular soils. Long term consolidation of deep soil layers shall be taken into account in the analysis. This may necessitate evaluation of contact pressure distribution both immediately after construction and after completion of the consolidation process. The design must be based on the worst conditions. 4.5.4 Rigidity of the Foundation - Rigidity of the foundation tends to iron out uneven deformations and thereby modifies the contact pressure High order of rigidity is characterized by large moments and distribution. relatively small, uniform settlements. A rigid foundation may also generate high secondary stresses in gtructural members. The effects of rigidity shall be taken into account in the analysis. 4.5.5 Rigidity of the Superstructure - Free response of the foundations to soil deformation is restricted by the rigidity of the superstructure. In the extreme case, a stiff structure may force a flexible foundation to behave as rigid. This aspect shall be considered to evaluate the validity of the contact pressure distribution. 4.6 Heavy Vibratory Loads - Foundations loads should preferably be isolated.
7
In case the structure supported by the raft consists of several parts with varying heights and loads, it is advisable to provide expansion joints between these parts. Joints may also be provided wherever there is a change in the direction of the raft.
5. METHODS OF ANALYSIS
5.0 The essential task in the analysis of a raft foundation is the determination of the distribution of contact pressure underneath the raft which is a complex function of the rigidity of the superstructure, raft itself and the supporting soil, and cannot except in very simple cases, be determined with exactitude. This necessitates a number of simplifying assumptions to make the problem amenable to analysis. Once the distribution of contact pressure is determined, design bending moments and shears can be computed based on statics. The following methods of analysis are suggested which are distinguished by the assumptions involved. Choice of a particular method should be governed by the validity of the assumptions in the particular case. 5.1 Rigid Foundation ( Conventional Method ) - This is based on the assumptions of linear distribution of contact pressure. The basic assumptions of this method are: a) The foundation is rigid relative to the supporting soil and the compressible soil layer is relatively shallow. b) The contact pressure variation is assumed as planar, such that the centroid of the contact pressure coincides with the line of action of the resultant force of all loads acting on the foundation. 5.1.S This method may be used when either of the following conditions is satisfied: a) The structure behaves as rigid ( due to the combined action of the superstructure and the foundation ) with a relative stiffness factor K > 0.5 ( for evaluation of K, see Appendix C ). b) The column spacing is less than 1*75/X( see Appendix C ). 5.1.2 The raft is analysed as a whole in each of the two perpendicular directions. The contact pressure distribution is determined by the procedure outlined in Appendix D. Further analysis is also based on statics. 5.1.3 In cases of uniform conditions when the variations in adjacent column loads and column spacings do not exceed 20 percent of the higher value. the raft may be divided into perpendicular strips of widths equal to the distance between midspans and each strip may be analysed as an independent beam with known column loads and known contact pressures.
8
IS : 2950 ( Part I ) - 1981 Such beams will not normally satisfy statics due to shear transfer between adjacent strips and the design may be based on suitable moment coefficients, or on moment distribution.
Nore - On soft soils, for example, normally consolidated clays, peat, muck, organic silts, etc. the assumptions involved in the conventional method are commonly justilied.
5.2 Flexible Foundation 53.1 Simplijed Method - In this method. it is assumed that the subgrade consists of an infinite array of individual elastic springs each of which is not affected by others. The spring constant is equal. to the modulus of subgrade reaction ( k ). The contact pressure at any point under the raft is, therefore, linearly proportional to the settlement at the point. This method may be used when the following conditions are satisfied (see Appendix E ): The structure ( combined action of superstructure and raft ) may be considered as flexible ( relative stiffness factor K > 03, see Appendix C ). Variation in adjacent column load does not exceed 20 percent of the higher value. 5.2.1.1 General method - For the general case of a flexible foundation not satisfying the requirements of 5.2.1, the method based on closed form solution of elastic plate theory may be used. This method is based on the theory of plates on winkler foundation which takes into account the restraint on deflection of a point provided by continuity of the foundation in The distribution of deflection and contact pressure orthogonal foundation. on the raft due to a column load is determined by the plate theory. Since the effect of a column load on an elastic foundation is damped out rapidly, it is possible to determine the total effect at a point of all column loads within the zone of influence by the method of super imposition. The computation of the effect at any point may be restricted to columns of two adjoining bays in all directions. The procedure is outlined in Appendix F.
Nom - One of the recent general methods based on the above mentioned theory is numerical analysis by either finite difference method or finite element method. This method is used for accurate analysis of the raft foundation. The details of this method could be covered at a later stage.
6. STRUCTURAL DESIGN
6.1 The general design for loads, shrinkage, creep and temperature effects and provision of reinforcement and detailing shall conform ot IS : 4561978*, the foundation being considered as an inverted beam or slab. *Code of practice for plain and reinforced concrete ( r&f rev&ion).
9
A
( Es )
DETERMINATION OF MODULUS OF ELASTICITY AND POISSONS RATIO ( p ) A-l. DETERMJNATION OF MODULUS OF ELASTICITY
(E, )
A-l.1 The modulus of elasticity is a function of the composition of the soil, its void ratio, stress history and loading rate. In granular soils it is a func-
tion of the depth of the strata, while in cohesive soils it is markedly influenced by the moisture content. Due to its great sensitivity to sampling disturbance accurate evaluation of the modulus in the laboratory is extremely dimcult. For general cases, therefore, determination of the modulus may be based on field tests ( A-2 ). Where a properly equipped laboratory and sampling facility are available, Es may be determined in the laboratory ( see A-3 ). A-2. FIELD DETERMINATION A-2.1 The value of Es shall be determined from plate loan test given in TS : 1888-1982.
where intensity of contact pressure, least lateral dimension of test plate, settlement, P== Poissons ratio, I, = Influence factor, and = 0.82 for a square plate. 4= B= S=
A-2,1.1 The average value of E, shall be based on a number of plate load tests carried out over the area, the number and location of the tests, depending upon the extent and importance of the structure.
A-2.1.2 Eflect of Size - In granular soils, the value of Es corresponding to the size of the raft shall be determined as follows:
10
IS : 2950 ( Part I) - 1981 where Bj,BP represent sizes of foundation modulus determined by the plate load test. and plate and E, is the
A-2.2 For stratified deposits or deposits with lenses of different materials, results of plate load test will be unreliable and static cone penetration tests may be carried out to determine I&. A-2.2.1 Static cone penetration tests shall be carried out in accordance with IS :4968(Part III )-1976. Several tests shall be carried out at regular depth intervals up to a depth equal to the width of the raft and the results plotted to obtain an average value of E,. A-2.2.2 The value of Es may be determined ship: from the following relation-
E, = 2 Cra
where Cud = cone resistance in kgf/cm2. A-3. LABORATORY DETERMINATION OF Es
A-3.1 The value of Esshall be determined by conducting triaxial test in the laboratory [ see IS : 2720 ( Part XI )-19717 and IS : 2720 ( Part XII )-1981x ] on samples collected with least disturbances. A-3.2 In the first phase of the triaxial test, the specimen shall be allowed to consolidate fully under an all-round confining pressure equal to the vertical effective overburden stress for the specimen in the field. In the second phase, after equilibrium has been reached, further drainage shall be prevented and the deviator stress shall be increased from zero value to the magnitude estimated for the field loading condition. The deviator stress shall then be reduced to zero and the cycle of loading shall be repeated. A-3.3 The value of & shall be taken as the tangent modulus at the stress level equal to one-half the maximum deviator stress applied during the second cycle of loading.
*Method for subsurface sounding for soils : Part III Static cone penetration test (firsi revision ). tMethods of test for soils : Part XI Determination of shear strength parameters of a specimen tested in unconsolidated undrained triaxial compression without the measurement of pore water pressme. 2Methods of test for soils : Part XII Determination of shear strength parameters .of soils from consolidated undrained triaxial compression test with measurement of pore water pressure (first revision ).
11
APPEND1
X B
[Clause 3.1(f)]
DETERMINATION OF MODULUS B-l. GENERAL B-l.1 The modulus of subgrade reaction ( k ) as applicable to the case of load through a plate of size 30 Y 30 cm or beams 30 cm wide on the soil is given in Table 1 for cohesionless soils and in Table 2 for cohesive soils. Unless more specific determination of k is done ( see B-2 and B-3 ), these values may be used for design of raft foundation in cases where the depth of the soil affected by the width of the footing may be considered isotropic and the extrapolation of plate load test results is valid.
TABLE 1 MODULUS OF SUBCRADE REACTION ( k ) FOR COHRSIONL.ESS SOILS
SOIL CHARACTERISTIC *MODULUS OF SULIGRADE REACTION ( k ) IN kg/cm3
OF SUBGRADE REACTION
Moist
TABLE 2 MODULUS
#--_---,--Consistency (1)
SOIL CHARACTERISTIC
(3) 2.7 2-7 to 5.4 5.4 to 108 are based on the ultimate bearing
Stifi 1 to 2 Very stiff 2 to 4 Hard 4 and over *The values apply to a square plate 30 x 30 cm. The above values assumption that the average loading intensity does not exceed half the capacity.
12
PartI)-
B-2.1 In cases where the depth of the soil affected by the width of the footing may be considered as isotropic, thevalue of k may be determined in accordance with IS : 9214-1979*. The test shall be carried out with a plate of size not less than 30 cm.
B-2.2 The average value of k shall be based on a number of plate load tests carried out over the area, the number and location of the tests depending upon the extent and importance of the structure. B-3. LABORATORY DETERMINATION
B-3.1 For stratified deposits or deposits with lenses of different materials, evaluation of k from plate load test will be unrealistic and its determination shall be based on laboratory tests [ see IS : 2720 ( Part XI )-1971t and IS : 2720 ( Part Xl1 )-1981$]. B-3.2 In carrying out the test, the continuing cell pressure may be so selected as to be representative of the depth of average stress influence zone (about 0.5 B to B ). B-3.3 The value of k shall be determined from the following relationship:
k =
0-65
I2
.+
-cc
. -1
B
where E, = Modulus of elasticity of soil ( see Appendix A ), fi= p I Youngs modulus of foundatipn material, = Poissons ratio of soil ( see Appendix A ), and = Moment of inertia of structure foundation. if determined or of the
.
B-3.4 Im the absence of laboratory test data, appropriate values of E, and p may be determined in accordance with Appendix A and used in B-3.2 for evaluation of k.
*Method of determination of subgrade reaction ( k value ) of soils in the field. tMethods of test for soils : Part XI Determination of shear strength parameters of specimen tested in unconsolidated undrained triaxial compression without the measurement of pore water pressure. tMethods of test for soils : Part XII Determination of shear strength parameters of soil from consolidated undrained triaxial cdrnpression test with measurement of pore water pressure (first revision ).
13
IS:29SO(PartI)-1981 B-4. CALCULATIONS B-4.1 When the structure is rigid ( see Appendix C ), the average moduhrs of subgrade reaction may also be determined as follows: k, =: Average contact pressure Average settlement of the raft
C-l.1 The flexural rigidity EI of the structure of any section may be estimated according to the relation given below ( see also Fig. 2): EI = where EL = modulus of elasticity material ) in kg/cma, Ii b H= = length or breadth bending, of the infilling material ( wall
Es = modulus of elasticity of frame material in kg/cmg, IO = moment of inertia of the beam in cm, Zt4 = I& = I* K h
h,
14
I
h,
length of the upper column in cm, If -_( I moment of inertia of the lower column in cm4, and moment of inertia of the foundation beam or raft in cm.
I,
II I/
NOTE The summation is to be done over all the storeys, including the foundation beam of raft. In the case of the foundation, Ifreplaces Ia and Ir becomes zero, whereas for the topmost beam; I becomes zero.
C-2. RELATIVE STIFFNESS FACTOR K C-2.1 Whether a structure behaves as rigid or flexible depends on the relative stiffness of the structure and the foundation soil. This relation is expressed IS
IS : 2950( Part I ) - 1981 by the relative stiffness factor K given below: a) For the whole structure K = EE&
0
&8
where EZ = flexural rigidity of the structure over the length ( a ) in Wm2, Es = modulus of compressibility of the foundation soil in kg/cm, b I length of the section in the bending axis in cm, a d R= = length perpendicular to the section under investigation in cm, = thickness of the raft or beam in cm, and radius of the raft in cm. 0.5, the foundation OF CRITICAL may be considered SPACING as rigid
C-3. DETERMINATION
COLUMN
C-3.1 Evaluation of the characteristics h is made as follows: h-4 -where k = modulus of subgrade reaction in kg/cm* for width B in cm ( see Appendix B ). B = width of raft in cm EC = modulus of elasticity of concrete in kgf/cms Z = moment of inertia of the raft in cm* footing of kB J- 4E,Z
16
4= +i
where
Qe;
IYrtI,X e
Qek
Y
ek, ei, ZL, Z; = eccentricities and moments of inertia about the principal axes through the centroid of the section, and x, y = co-ordinates of any given point on the raft- with respect to the x and y axes passing through the centroid of the area of the raft. Zi, $, ei, e; may be calculated from the following equations:
z; =I,z; = Iv ei = ee -
1:
T--,
Zv
7 i?
25
Z
Z I,
ev, and
e;=ev where
zy em zv
I,, Zv = moment of inertia of the area of the raft respectively about the x and y axes through the centroid, 17
IS : 2950 ( Part I ) - 1981 I,, = J xydA for the whole area about x and y axes through the centroid, and ee, o,, = eccentricities in the x and y, directions centroid. For a rectangular raft the equation simplifies to: of the load from the
where LIand b :.=-: dimensions of the raft in the x and y directions the respectively.
NOTE - If one or more of the values of ( q ) are negative, as calculated formula, it indicates that the whole area of foundation is not subject to only a part of the area is in contact with the soil, and the above formula good, provided appropriate values of L,. I,. I,., e z and ey are used with area in contact with the soil instead of the whole area. by the above pressure and will still hold respect to the
CONTACT PRESSURE DISTRIBUTION AND MOMENTS BELOW FLEXIBLE FOUNDATION E-l. CONTACT PRESSURE DISTRIBUTION
E-l.1 The distribution of contact pressure is assumed to be linear with maximum value attained under the columns and minimum at mid span. El.2 The contact pressure for the full width of the strip under an interior column load located at point i (pi ) can be determined as ( see Fig. 3B ):
pi = 7 , 48_Mi I?
where I = average length of adjacent span ( m ), Pi = column load at poiflt i ( t ), and Md = moment under an interior columns located at i. 18
IS : 2950 ( Part I ) - 1981 E-l.3 The minimum contact pressure for the full width of the strip at the middle of the adjacent spans p,,,~ and pmr can be determined as ( see Fig. 3A ):
PmZ =
ZPi~--ppt7;
It
2 where I,, 16as shown in Fig. 3A. El.4 If E-2.3( a) governs the moment under the exterior columns, contact pressures under the exterior columns and at end of the strip pd and pe can be determined as ( &see Fig. 3C ):
4P* + ps = po = -C-a- -
6M. -
pml1
&
3M. PC 2
Ps, pm, M,, II, C as shown in Fig. 3C. where E-l.5 If E-2.3 ( b ) governs the moment under the exterior columns, the contact pressures ps and pe are determined as ( see Fig. 3C ): pc = pc =
L!!&?$
1
E-2. BENDING MOMENT DIAGRAM E-2.1 The bending moment under an interior Fig. 3A ) can be determined as: M<=-g ( 0.24ti + 016 )
column
located
at i ( see
E-2.2 The bending moment at midspan is obtained as ( see Fig. 3B ): M, = Mo + MI where M,, = moment of simply supported beam
where
at interior Column
3B Pressure Distribution
at Exterior Column
IS : 2950 ( Part I ) - 1981 E-2.3 The bending moment M, under exterior columns can be determined as the least of ( see Fig. 3C ): a)
b)
GENERAL CONDITION
F-l. CLOSED FORM SOLUTION OF ELASTIC PLATE THEORY F-l.1 For a flexible raft foundation with nonuniform column spacing and load intensity, solution of the differential equation governing the behaviour of plates on elastic foundation ( Winkler Type ) gives radial moment ( M, ) tangential moment ( Mt ) and deflection ( w ) at any point by the following expressions:
PL= w=40za
( +
where P = column load; r = distance of the point under investigation load along radius; 21 from column
IS : 2950 ( Part I ) - 1981 L = radius of effective stiffness; 4 D k J k = modulus of subgrade reaction for footing of width B;
D = flexural rigidity of the foundation; Et2
12 ( 1 - Pa ) t = raft thickness;
E = modulus of elasticity of the foundation
material;
material; and
Z,, Z;, Z, = functions of shear, moment and deflection ( see Fig. 4 ). F-l.2 The radial and tangential moments can be converted to rectangular co-ordinates:
M, _= M, co.9 4 -I- Mt sina 4 Mv = M, sin8 4 + Mt cos2 4
where 4 = is the angle with x axis to the line joining origin to the point under consideration.
F-l.3 The shear Q per unit width of raft can be determined by:
Q=-
&z;(+)
where 2; = function for shear ( see Fig. 4 ). F-l.4 when edge of the raft is located within the radius of influence, the followmg corrections are to be applied. Calculate moments and shears perpendicular to the edge of the raft within the radius of influence, assuming the raft to be infinitely large. Then apply opposite and equal moments and shears on the edge of the mat. The method for beams on elastic foundation may be used.
:
F-1.5 Finally all moments and shears calculated for each individual column and walls are superimposed to obtain the total moment and shear values. 22
:
I I
3 r/L
FIG.
4 FUNCTIONS FORSHEARMOMENTAND
DEFLECTION
23
Representing
Subcommittee,
BDC 43
Members
DEPUTY DIRE~OR EXECWWE ENGINEER DESIGN) V ( SHRIT. N. MUKHERJEE
( B & S ), CB-II
Organization,
SHRI AMAR S~NGH ( Alfernate ) Engineering Research Laboratories, Hyderabad SHRI K. R. SAXENA Cement Corporation of India, New Delhi SHRI 0. S. SRIVASTAVA SHRIS. K. CHAPERJEE( Alternate )
SHRI B. G. RAO
Central Public Works Department, New Delhi Martin & Bums Co Ltd, Calcutta Central Building Research Institute, Roorkee
DR SWAMISARAN
24
BUREAU
Headquarters Telephones Regional Central
l
OF.
:
INDIAN
STANDARDS
: 331 01 31
Telegrams
: Manaksanstha
331 13 75 Offices :
NEW DELHI 110002 Eastern : l/I4 C.I.T. Scheme VII M. V.I.P. Road, Maniktola, CALCUTTA 700654 Northern : SC0 445-446, Sector 35-C, CHANDIGARH 160036 Southern : C.I.T. Campus, IV Cross Road, MADRAS 600113 Western : Manakalaya, E9 MIDC. Marol. Andheri (East), BOMBAY 400093 Branch Offices : 380001
Pushpak, Nurmohamed Shaikh Marg. Khanpur, AHMADABAD t Peenya Industrial Area, 1st Stage, Bangalore-Tumkur Road, BANGALORE 560058 GangotriCompfex. 5th Floor, Bhadbhada Road, T.T. Nagar. BHOPAL 462003
2 63 48 39 49 55 55 40 21 5 36 27 2 67 05 8-71 i9 96 3 31 77 231083 6 34 71 21 68 76 5 55 07 6 23 05 6 21 04
Plot No. 82/83, Lewis Road, BHUBANESHWAR 751002 Kalai KBthir Building, 6/48-A Avanasi Road, COIMBATORE 641037 Quality Marking Centre, N.H. IV, N.I.T., FARIDABAD 121001 Savitri Complex, 116 G. T. Road, GHAZIABAD 201001 53/5 Ward No. 29, R.G. Barua Road, 5th Bv-lane, GUWAHATI 781003 5-8-56C L. N. Gupta Mary, ( Nampallv Station Road ) HYDERABAD 500001 R14 Yudhister Marg, C Scheme. J,AIPUR 302005 * 117/418 B Sarvodaya Nagar. KANPUR 208005 Plot No. A-9, House No. 561/63. LUCKNOW 226005 Patliputra Industrial Estate, PATNA District Industries Centre Complex. SRINAGAR 190011 Sindhu Nagar, Kanpur Rosa. 800013 Bagh-e-Ali Maidan.
T. C. No. 14/1421, University P. 0.. Palayam. THIRUVANANTHAPURAM 695034 Inspection Offices (With Sale Point)
:
52 51 71 5 74 35
Pushpanjali. First Floor, 205-A West High Court Road Shankar Nagar Square, NAGPUR 440010 Institution of Enyineels (India) Building, 1332 Shivaji Nagar. PUNE 411005 Sales Office Calcutta is at 5 Chowringhee Approach, P. 0. Princep Street, CALCUTTA t Sales Office is. at Novelty Chambers, Grant Road, BOMBAY Square, $ Sales Office is at Unitv Building, Narasimharaja BANGALORE Reprography
27 68 00 89 65 28 22 39 71
Unit,
IS t
AMENDMENT
NO. 1
TO
DECEMIIER
lY88
CODE OF PRACTICE FOR 2950. ( Part 1) - 1981 DESIGN AND CONS11~UCIION 01: RAF1 FOUNDATIONS
PART 1 DESIGN
( Second
[ Puge 4, cfawe 3.1(g) ] 1978f. ( Page 4, foot.note
for the existing foot-note: And
tC0do ol prnclico
Revision
/
IS : 1904.
following
Substitute
IS : 1904-1987SJofor
the
marked
roqrtirornancn [ Past
5.2.1 (a),
fine
2 ] -
Substitute
.rr4 !J.l.l.fir
K
_ffc
.K
Substitute
the
following
for
rollowing
for the
value
of
~rPcw+mn+P~(~)l
2 I
[ Page
existing
, clause E2.3
(b) J -
Substitute
the
following
for
the
of w.
( Page 2% &use
places.
F-1.3
>-
Substitute
<,&r
2:
appcarirlg
at
two
( BDC
43 )
Kcprogmphy
Delhi,
lnd%