Anti Pick 109

C1/SfB Yt4 March 2010
ANTI-PICK 109
High Modulus Hybrid Sealant
Description
ANTI PICK 109 is a one part, chemically curing solvent free sealant based on Everbuild Hybriflex technology, combining the best qualities of silicone and polyurethane. Anti Pick 109 has been specifically formulated to provide a degree of resistance to finger picking answering the need for a harder to pick by hand seal (in comparison to traditional sealants) where a small movement accommodation is required.
Available in Benefits
Excellent impact and wear resistance. Resistant to picking by fingers. Excellent primerless adhesion to most surfaces, including metals, most plastics, glass, polyester. High UV and aggressive atmosphere resistance. Excellent resistance to Chemicals & petrol (10% dilute acids, alkalis, most solvent) Overpaintable with certain paints (compatibility test should be made). Can be applied on damp surfaces. Non hazardous to health. High mechanical properties. Passed for use on different home office, national offender management services and ministry of justice projects. 300ml Cartridge, available in the following colours: White Soft Linen Grey
Storage
Store in cool, dry conditions between +5C and +25C. Storage outside these parameters will dramatically reduce shelf life.
Recommended For
Secure environments i.e. prisons & hospitals where the sealant is hard to reach or the person is under supervision.. Municipal and public areas. Perimeter sealing of doors, windows and sanitary ware. Joints in heavy cladding.
Shelf Life
12 months from date of manufacture when stored as directed.
Everbuild Building Products Ltd, Site 41, Knowsthorpe Way, Cross Green Industrial Estate, Leeds, LS9 0SW Tel: 0113 240 3456 // Fax: 0113 240 0024 // www.everbuild.co.uk
ANTI-PICK 109
High Modulus Hybrid Sealant
Health & Safety

Data sheet available for professional user on request.
Joint Dimensions
For maximum movement accommodation, it is recommended that: 1. The sealant joint depth should be no less than 5mm 2. Joint depth should be 5mm for joints up to 10mm wide 3. Joints above 10mm in width should be half the width in depth up to 20mm and minimum 10mm for wider joints Joint depth may be adjusted to the correct size using EVERBUILD JOINT BACKER ROD.
Surface Preparation
All surfaces must be clean and dust free. Preliminary adhesion tests are strongly recommended prior to full scale application. Surfaces may be damp, but have no standing water. For most substrates, priming is not required, however, if in doubt contact our technical department.
Specific Data
Consistency Paste
Density
1.50 0.05
Limitations
Adhesion (and overpaintability) trials are recommended prior to full scale application It is the users responsibility to determine suitability for use. If in doubt, please contact Technical Services Department for advice
Application Temperature
5 to 35C
Skin Formation @ 23C and 50% RH
30 10 Min
Sagging (ISO 7390) Nil
Movement Factors
+/- 20% Movement Accommodation
Curing at @ 23C and 50% RH Shore A Hardness (ISO 868 - 3 seconds) Modulus at 100% elongation (ISO 8339) Tensile Strength (ISO 8339)
> 3mm / 24Hr
Approx 60
> 1.5 MPa
Primer
> 2.6 N/mm
Joint Width Calculation

Joint widths are calculated as in BS6213: Width = M x 100 + M F Where M = movement and F = movement accommodation Factor
Shrinkage (ISO 10563)
>2%
Priming is not always necessary; but if in doubt use a suitable primer as directed prior to application; especially when joints are to be immersed or require a high movement capability.
Resistance to UV Radiation Compatibility With Paints
Excellent Water Based: Yes (test compatibility) Solvent Based: No (with Alkyd Paints) -40 to +150C
Service Temperature
Movement Accommodation
20% Approximately 11 linear meters per cartridge
Coverage
The technical data contained herein is based on our present knowledge and experience and we cannot be held liable for any errors, inaccuracies, omissions or editorial failings that result from technological changes or research between the date of issue of this document and the date the product is acquired. Before using the product, the user should carry out any necessary tests in order to ensure that the product is suitable for the intended application. Moreover, all users should contact the seller or the manufacturer of the product for additional technical information concerning its use if they think that the information in their possession needs to be clarified in any way, whether for normal use or a specific application of our product. Our guarantee applies within the context of the statutory regulations and provisions in force, current professional standards and in accordance with the stipulations set out in our general sales conditions. The information detailed in the present technical data sheet is given by way of indication and is not exhaustive. The same applies to any information provided verbally by telephone to any prospective or existing customer.
Everbuild Building Products Ltd, Site 41, Knowsthorpe Way, Cross Green Industrial Estate, Leeds, LS9 0SW Tel: 0113 240 3456 // Fax: 0113 240 0024 // www.everbuild.co.uk

Anti Pick 109

Uploaded by

Copyright:

Available Formats

Anti Pick 109

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Anti Pick 109

Uploaded by

Copyright:

Available Formats

C1/SfB Yt4 March 2010

Health & Safety

Skin Formation @ 23C and 50% RH

Sagging (ISO 7390) Nil

> 3mm / 24Hr

> 1.5 MPa

Joint Width Calculation

Shrinkage (ISO 10563)

Resistance to UV Radiation Compatibility With Paints

20% Approximately 11 linear meters per cartridge

You might also like